User ManualeXplorist TRX7

ReferencesIMPORTANT SAFETY WARNINGS

The Magellan eXplorist TRX is an Off-Road vehicle navigation aid designed to assist you in driving on your route and arriving to your selected destinations.

Please check with your state or local law enforcement for applicable regulations regarding mounting to the windshield.

The driver should enter data or program the Magellan device only when the vehicle is stopped. Only a vehicle passenger should enter data or program the device while the vehicle is moving.

It is your responsibility to comply with all traffic laws.

Every attempt is made to ensure that the database is accurate. However, roadways, points of interest (POIs), and business and service locations may change over time.

Keep the device safe from extreme temperature conditions. For example, do not leave it exposed to direct sunlight for an extended period of time. The minimum operating temperature is 14ºF (-10ºC), and the maximum operating temperature is 140°F (60°C).

Take care when mounting the device in your vehicle, whether using the windshield mount or other mount or accessories, so that the device does not obstruct the driver’s view of the road, interfere with the operation of the vehicle’s safety devices such as airbags, or present a hazard to occupants of the vehicle should the device become

dislodged while driving. Comply with all local, state, and federal laws before mounting the device in your vehicle.

You assume the risks associated with damage to your vehicle or vehicle occupants as the result of your choices in mounting the device.

The battery is rechargeable and should not be removed. In the event it should need to be replaced, please contact Magellan Technical Support or visit http://support.magellangps.com.

Charging the Magellan eXplorist TRX7

An AC adapter is included with your eXplorist TRX7. If you need to replace your AC adapter, use a 3.5V-5V 2A charger.

Only use the car charger approved for/supplied with your eXplorist TRX7. Use of another type of car charger will result in fire or electric shock.

For safety reasons, the battery in your eXplorist TRX7 will stop charging when the ambient temperature is less than 32°F (0°C) or more than 113°F (45°C).

It will take approximately 4 hours of charging the eXplorist TRX device through the vehicle power adapter or optional AC adapter to obtain a full battery charge. It is recommended that you charge the battery initially for at least 2 hours.

Use only the charger approved for your Magellan eXplorist TRX device.

Estimated usage of the eXplorist TRX

Section TitleSafety

ReferencesSafetyon battery power is approximately 4-6 hours.

FCC RF Radiation Exposure Statement

1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.

Wi-Fi 5G Band 1 is for indoor use only.

Canada, Industry Canada (IC) Notices

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Canada, avis d’Industry Canada (IC)

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.

© 2015 MiTAC International Corporation. The Magellan logo and Magellan are registered trademarks of MiTAC International Corporation, and OneTouch is a trademark of MiTAC International Corporation and are used under license by MiTAC Digital Corporation. All rights reserved. All other trademarks and registered trademarks are property of their respective owners.

All other products and brand names are trademarks of their respective holders.

No part of this user manual may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, for any purpose other than the purchaser’s personal use, without the prior written permission of MiTAC International Corporation.

The information provided in this document is correct at the time that it is created. MiTAC International Corporation assumes no responsibility or liability for any errors or inaccuracies that may appear in the contents of this User Manual.

Magellan Take-Back ProgramMagellan’s Take-Back Program provides a way for customers to recycle certain Magellan equipment. As part of this program, all Magellan GPS models will be accepted.Visit magellanGPS.com for more information.

ReferencesMagellan Explorist TRX7

Magellan eXplorist TRX7 connects you and your vehicle to superior outdoor adventure lifestyles experiences.

While off-road, users with Magellan’s Off-Road GPS Navigation System can record off-road adventures and log Dirt Miles, capture and share adventures by creating tracks and marking waypoints to share with the eXplorist TRX community, find new trails submitted by other eXplorist TRX users, share favorite trails with the community, and more.

It all starts with Magellan eXplorist TRX7.

With the TRX7, you can:

• Search for Trails, Trips, and Points of Interest (POIs) preloaded into your TRX7 and easily route to any location.

• Create a Wish List of Trails, Trips, and POIs for future navigation.

• Track and record Trails and off-road routes.

• Log detailed waypoints, such as water, obstacles, and scenic spots, along a Trail or route.

• Earn achievements as you log Dirt Miles through the United States and Canada.

• Create an Account Profile with customized vehicles and sync your profile with TRX Web at http://mytrxjournal.com.

• Connect your profile to Twitter and Instagram to share your adventures with the TRX community.

• Keep your own Trail log and access a database of Trails published by the TRX user community.

Introduction

ReferencesGetting Started at Home

Connect to Wi-Fi

1. From the Home screen, tap Apps --> Settings --> Wi-Fi.

2. Tap the On/Off button to turn Wi-Fi on.

3. Select the desired network under Wi-Fi networks.

4. Enter password (if applicable) and tap connect.

Your TRX7 is now connected to a Wi-Fi network.

Register Your Account

Refer to Create Your Profile for details about registering your TRX account.

Getting Started in Your Vehicle

Choose a location

Find a location with a clear view of the sky.

Clean the surface

Clean the area on the windshield where you want to mount the device. Allow the surface to dry.

Install the mounted device

1. Hold the suction cup firmly against the windshield surface

2. Push the level towards the base.

3. Screw the AMPS plate on the cradle.

4. Attach the device onto the mount.

Power On

Press the Power button, located on the right side of the device, to turn the device on.

Connect to Wi-Fi Hot Spot

1. From the Home screen, tap Apps --> Settings --> Wi-Fi.

2. Slide the button to the right to turn Wi-Fi on.

3. Select the desired network under Wi-Fi networks.

4. Enter password (if applicable) and tap Connect.

Your TRX7 is now connected to a Wi-Fi Hot Spot.

Note: Wi-Fi must be ON in order to synchronize your TRX7 with your TRX Web account.

Getting Started

ImportantVarious factors influence GPS signal reception. Here are tips to help improve the signal reception and time to calculate the current location.• Leave any enclosed structure (garage,

parking structures, etc.).• Make sure you have a ‘clear view of the

sky’. Buildings and trees can have an impact on GPS signal reception.

• Make sure that the device is mounted where it can have a clear line of sight to the windshield.

Note: The first time the device calculates its location can take up to 1 minute. Subsequent times will be 15 seconds on average.

ReferencesOverview

1. Microphone

2. Touchscreen

3. Lanyard attach point

4. POWER button

5. Volume buttons

6. MUTE button

7. RESET button (unused)

8. Camera button (unused)

9. BACK button

10. HOME button

11. MENU button

12. Cradle screws

13. Speakers

14. Pogo pins

15. Mount Plate

16. Mini-USB Power port

17. Headphone jack

18. USB port (unavailable)

19. Memory card slot

20. Cover latch

Note: Use caution when opening the USB power port and headphone jack covers to avoid damaging the covers.

Note: The Camera button is not yet implemented in this release.

ReferencesPowering On the TRX7

The Power On/Off button is located on the right side of the TRX7 receiver, above the Volume buttons.

Press the Power button until you hear a click, then release the button. The Boot screen displaying the Magellan logo will appear.

The Boot screen disappears, and the Lock screen appears, displaying the time, date, and the Lock icon.

Turning On the TRX7

Slide the Lock icon in any direction to unlock the device. You will view either the Home screen or the last screen displayed when you turned off the TRX7.

Turning Off the TRX7

To lock the device, simply press the Power button.

To power the device off completely:

1. Press and hold the Power button for 3 seconds.

2. Select Power off from the menu that appears.

From this menu, you can also:

• Turn the device to Airplane Mode to deactivate all data connections (Wi-Fi, Bluetooth, etc.).

• Restart the device.

• Turn the device on Silent mode to turn off all device sounds.

Note: you can still track your progress while the device is in Airplane Mode.

Viewing the Battery Level Indicator

The Battery Level is always displayed on the top right corner of the screen. The Battery Level is indicated by a battery-shaped icon that is colored blue based on the percentage of battery life remaining.

To view more Battery Level details:

1. Slide your finger downward from the top right corner of the screen.

2. Tap on the Battery icon, which displays the percentage of battery power left in the device.

3. A display screen will appear:

You can tap on any of these options to display details of each type of battery use.

The TRX7 can normally function for 4-6 hours on battery when the battery is charged to 100%.

Fundamentals

ReferencesChecking GPS Status

Both the top left and right corners of the screen give you access to your GPS Status.

To view detailed GPS Status:

1. Slide your finger downward from the top left corner of the screen.

2. Tap on Location set by GPS.

A display screen will appear with the following options:

• Access to my location: allows you to give permission to apps on the device to use your location information. Tap On or Off to use this function.

• Location Sources

• GPS satellites: lets apps use GPS on your eXplorist TRX7 to pinpoint your location. This option is automatically selected when you turn On access to your location.

You can also view detailed GPS Status from the top right corner of the screen:

1. Slide your finger downward from the top right corner of the screen.

2. Tap on Settings.

3. Scroll down the menu that appears to Location access. This will display the same options described above.

Volume

You can adjust the volume up and down using the two Volume buttons on the right side of the eXplorist TRX7 (under the Power button).

When you use these buttons, a volume indicator appears on the screen. You can also adjust the volume by tapping on the circle in the volume level and sliding it left (for volume down) and right (for volume up).

You can also tap to open a Notification volume level. Slide this indicator left and right to adjust notification volume.

Brightness

1. Slide your finger downward from the top right corner of the screen.

2. Tap Brightness.

3. Tap the circle in the Brightness control indicator and slide the indicator left (to decrease brightness) and right (to increase brightness).

Fundamentals

ReferencesHome Screen

The Home Screen displays the TRX7 Dashboard app, the current time and date, the weather at your GPS location, and other basic functions.

The Home Screen allows you to access:

• Magellan eXplorist TRX7 Dashboard

• Internet browser

• Apps, Widgets, and Settings

• Contacts List

Note: eXplorist TRX7 is built on Ulmo Pro N496(x) Series tablet device hardware. Please refer to the N497(x) Series User Manual for detailed information about the tablet’s technical specifications, hardware, memory, connectivity, troubleshooting, and more.

Note: eXplorist TRX7 uses the Android 4.2.2 “Jelly Bean” software platform. Please refer to Android Jelly Bean software documentation for detailed information about Jelly Bean apps, widgets, and other user functions.

Dashboard

The TRX7 Dashboard is the central hub of activity for the use of your TRX7. From the Dashboard, you can:

• Track Me: Track your progress in real-time using your device GPS location

• Journal: Manage your Trail Log and Wish List

• Search: Explore your surroundings using a Map or List view

• Settings: Access software updates, your Account Profile, Social Networks, Achievements, Data/Account Resets, and view TRX7 Product Information

• View your total number of Dirt Miles, Trails, and Achievements

You can access the Dashboard by tapping the ORV app icon on the Home screen.

Home Screen and Dashboard

ReferencesCreate an Account on TRX Web

Before using the TRX7 for viewing and tracking Trails, create an account on http://mytrxjournal.com to access your device information online.

1. Select Sign In.

2. Select Create Account.

3. Fill in the following fields:

4. Select Create Account to confirm the creation of your new TRX Web account. A confirmation email will be sent to your email address inbox.

Once you’ve confirmed your account through the email you received, return to your device and complete the following steps to sync your TRX7 with your new account:

1. Tap Settings on the Magellan Dashboard screen.

2. Tap Account Profile and enter the email address and password that you used to create your TRX Web account.

3. Tap Connect to log into your account.

Note: Alternatively, tap on Register New Account to create the account from the device. However, it is recommended that you create your account on the TRX Web online platform.

Refer to Using Your TRX Web Account Profile Online for more details about using the TRX Web homepage.

Create Your Profile

ReferencesCreating a Vehicle Profile

You can create a customized Vehicle Profile for use with your account so that the TRX user community knows your vehicle of choice (or so you can show it off).

To create a Vehicle Profile:

1. Tap Settings on the Dashboard.

2. Tap Account Profile in Settings.

3. Tap Vehicles on the Account Profile screen to enter the Vehicle Profile.

4. Tap the Pencil button and Select Add Vehicle.

5. Enter your vehicle information: Nickname, Year, Make, Model, and City and State.

6. Check Active Vehicle if this will be your primary vehicle.

7. Tap Edit (below the vehicle image) to add a picture of your vehicle from your device (optional).

8. Tap Save.

You have successfully added a vehicle to your Account Profile. You can add multiple vehicles by simply tapping the

Pencil button and selecting Add Vehicle from the Vehicles Profile page.

The first vehicle you add will automatically be designated as your Active Vehicle.

To select a different Active Vehicle from your list of vehicles:

1. Tap on the vehicle you wish to assign as your Active Vehicle.

2. Tap on the Active Vehicle check box.

3. You will see a prompt that says Change active vehicle? Select OK to confirm the change, or Cancel to stop the change.

Create Your Profile

ReferencesLinking Your Social Media Accounts

You can link your Twitter and Instagram accounts to your Account Profile to share Tweets about your Dirt Miles and pictures of your experiences on the Trail. This lets you alert your friends that you’ve found a new Trail, share your adventures with the TRX7 user community, and more.

Linking Your Twitter Account

To link your Twitter account to share instant updates from the Trail to your Twitter feed:

1. Tap Settings.

2. Select Social Networks.

3. Tap on + next to the Twitter option.

4. Tap Connect.

5. Enter your User Name and Email Address and Password and tap Connect.

6. Tap Done to finish linking your Twitter account.

Create Your Profile

ReferencesCreate Your ProfileLinking Your Instagram Account

To link your Instagram account to share pictures from the Trail:

1. Tap on + next to the Instagram option.

2. Tap Connect.

3. Enter your User Name or Email Address and Password and tap Connect.

4. Tap Done to finish linking your Instagram account.

ReferencesTrack Logging

To begin logging your progress on a Trip, Trail, or other route:

1. Tap Track Me from the Dashboard. The Map Screen will open and tracking will start automatically.

2. Tap to pause tracking.

3. Tap to resume tracking.

While tracking your progress, you can:

Toggle between North Up and Track Up views.

Toggle between a 2D and 3D view.

Note: The Toggle icon turns blue whenever you pan around the map. Tap on the blue icon to snap the map view back to your current location.

Pausing your progress will display more options.

Mark Waypoint: Record an Audio Waypoint, select a specific Waypoint at your Current Location, mark a Point on Map, and Enter Coordinates. This is also available while tracking is in progress.

Social Post: Share your progress on Twitter with an automatic Tweet.

Backtrack: Follow your route back to where you began.

Finish: Save your Trail with details about the Trail terrain, pitch, tilt, a custom rating, and more.

Mark Waypoints

Add details to your Trail by marking Waypoints. Whether you want a steep, muddy, challenging Trail or a flat, dry, leisurely ride, Waypoints allow you to make that call before you head to the Trail. The more Waypoints you add to a Trail, the easier it will be for you and other users to judge which Trails are best for each off-roading adventure.

You can save both a custom Waypoint and a Quick Waypoint.

Using Your eXplorist TRX7

ReferencesUsing Your eXplorist TRX7To save a custom Waypoint:

1. Pause your tracking progress.

2. Tap Mark Waypoint .

3. Select one of the following options:

Audio Waypoint: Record a custom audio message describing the Waypoint.

Current Location: Select a Waypoint to add detail to Waypoint information:

Point on Map: Tap anywhere on the map to save a Waypoint in that specific location. You can also view a list of nearby Waypoints when you save a Waypoint on the map.

Coordinates: Enter specific coordinates to save a Waypoint.

4. Tap Save when you’ve finished creating the Waypoint.

To save a Quick Waypoint while tracking your progress:

1. Tap Mark Waypoint .

2. Tap on the Waypoint you want to mark:

3. Choose a detailed Waypoint option under the Waypoint you selected.

4. Tap Save to the save the Waypoint on your Trail, or tap Cancel to stop creating a Waypoint.

Each Waypoint will appear on your Trail log when you save the Trail to your TRX Web account.

Social Post

Tweeting your progress from a Trail lets your friends and other riders know where you’re riding and how many Dirt Miles you’ve driven.

To post a Tweet to your linked Twitter account:

1. Pause your Tracking progress.

2. Tap on Social Post .

3. Tap OK when you see the notification This will post upon connection. You will see this notification if you’re not connected to Wi-Fi.

ReferencesUsing Your eXplorist TRX7

4. Tap OK.

A preformatted Tweet will be shared with your followers, letting them know you’re out on the Trail having a good time.

Backtrack

To follow the Trail you’ve created in reverse:

1. Tap Backtrack to get back to your starting point. You will see this notification:

2. Tap either OK to begin backtracking, or Cancel to return to the Pause screen.

Finish (Save)

Once you’ve finished logging your Trip or Trail, you can save your route from your device. To save your route:

1. Tap Pause when you’ve finished tracking your progress.

2. Tap Finish . You will see a new

screen with customizable trail attributes.

3. Tap on the text box that says Name to enter a custom Trail name with the device keyboard.

4. Select a 4WD (four-wheel drive) option: NO, Some, or Must.

5. Select a 4LO (low-gear) option: NO, Some, or Must.

6. Select Terrain type: Solid, Loose, or Rutted.

7. Select detailed Terrain information:

8. Select a Pitch, Tilt, and Rating from 1-5 stars.

ReferencesUsing Your eXplorist TRX7

9. Tap the Comment text box to enter a customized message about the Trail.

10. Tap Save to sync the Trail information to your account, or Discard to stop saving the Trail.

Your trail will also be assigned one of four Difficulty levels:

Easy

Intermediate

Advanced

Expert only

Once you have saved and uploaded a Trail to your account, you and other users in the TRX community can view the Trail’s route, Waypoints, and attributes.

Note: Entering Trail details is optional at the time of saving, but is mandatory before publishing the Trail on Magellan Public Trail Database.

Journal

All of your saved Trails, Waypoints, and

Points of Interest (POIs) will be available in your from the Dashboard screen.

Log: Shows your completed Trips, Trails, and Waypoints in chronological order with the most recent at the top.

Wish List: Shows Trips, Trails, and Waypoints that have been saved from Search.

To create a new Trip with previously saved Trips and Trails:

1. Tap and tap .

2. Type the name you want for the trip.

3. Tap Done on the keyboard.

4. Tap the check box next to each trip that you wish to add.

5. Tap Save.

ReferencesUsing Your eXplorist TRX7You can also delete previously saved Trips in your Journal:

1. Tap .

2. Tap on the Trail(s) you wish to delete so that the box on the right side of the Trail information is checked.

3. Tap .

4. Select OK to delete the selected entries, or Cancel to return to your Log.

To go to a place that you’ve previously saved to your Wish List:

1. Tap on an item on your Wish List.

2. Tap on Go.

Search

To search for Trails, Waypoints, POIs, or other preloaded or custom landmarks, tap on the Dashboard.

You have several options in the Search menu:

View all Trails and Waypoints on a dynamic 2D/3D map around your current GPS location.

Pan around the map and tap on a Waypoint on the Map screen to view the attributes of and distance to the Waypoint from your location.

You can also save a Waypoint to your Wish List by tapping on Save on the bottom right corner of the Waypoint Info screen.

View a list of all Trails and Waypoints around your current GPS location.

Customize a search for a nearby Trail or Waypoint.

ReferencesUsing Your eXplorist TRX7To filter a search for a nearby Trail, Waypoint, or POI with the Map Filter:

1. Tap on the Map button.

2. Select a Type of location:

Note: The Places option allows you to search for nearby pre-loaded locations, including stores, restaurants, gas stations, recreational areas/facilities, and more.

3. Select Difficulty (Easy to Expert):

4. Select a Rating (1-5 Stars):

5. Tap on Filter to populate the Map with results using your filters.

6. Tap on a Trip, Trail, or POI that appears on the Map to view its attributes and, if desired, save it to your Wish List.

To filter a search using the List Filter:

1. Tap on the List button.

2. Select a Type, Difficulty, and Rating.

3. Tap Sort By to organize your search results:

4. Tap Filter to view a list of your filtered search results.

Tap on any of these results to view the attributes of the Trip, Trail, or POI. Tap Save to add the item to your Wish List.

Achievements

As you drive on Trips and Trails throughout the United States and Canada, you will earn achievements that will be displayed on your Account Profile.

When you earn an achievement after driving a Trip or Trail, you will see screen like this:

ReferencesUsing Your eXplorist TRX7All of your achievements will be displayed on your TRX Web profile page. You can also view your achievement on your device:

1. Tap Settings on the Dashboard screen.

2. Tap Achievements in Settings to see all the awards and badges you’ve earned.

3. Tap All Achievements to see a list of all of the achievements that you can earn.

Resets

If necessary, you can reset your Dirt Miles, delete all data associated with your account, or delete your account completely.

To perform any of these resets:

4. Tap Settings on the Dashboard.

5. Tap Resets in Settings to open a list of reset options.

6. Tap your desired Reset option.

7. Tap OK to confirm the reset, or Cancel to stop the reset.

Note: You will need to enter your account password before you delete your account. Enter your password and your account will be permanently deleted.

ReferencesUsing TRX Web

You can access many of the functions of the eXplorist TRX7 on http://mytrxjournal.com. All of the data you save on your TRX7 device will automatically sync with your TRX Web account and can be reviewed, edited, and saved on your online TRX Web homepage.

To sign in to your TRX Web account online:

1. Go to http://mytrxjournal.com.

2. Select Sign In at the top right corner of the screen.

3. Enter your Email Address and Password.

4. Select Sign In.

Once you’ve logged in, your can view your Wish List and Log. You can also zoom in and out of the Map using the + and - buttons on the right side of the screen.

From this page, you can also select Profile on the top right corner of the screen to:

• View your most recent achievements you’ve earned

• Connect your Account Profile to your Twitter and Instagram accounts

• Edit your Account Profile

• Logout of TRX Web

Log and Wish List

You can access your account’s Wish List and Log on the right side of the page.

Select any Trails, POIs, or other items on your Wish List to view the item and its details on the Map.

Using TRX Web

ReferencesUsing TRX Web

To delete items from your Wish List:

1. Select the Trash icon next to the Wish List item.

2. Select Delete to remove the item from your Wish List, or Close to cancel the deletion.

On your Log, you can select any of your saved Trips to view Trip details, including Start and End Elevation and Terrain Specs. You can modify any of the Terrain Specs you included when you saved a Trip from your device.

To publish your Tracks, POIs, or Trips to the TRX user community:

1. Select the item you wish to publish.

2. Review the item details, such as Terrain Specs, to make sure that the Trip is as accurately described as possible for other users.

3. Add Notes in the text box to describe the Trip in as much detail as you’d like.

4. Edit the Review rating (from 1-5 Stars) if necessary.

5. Select Publish. A new window will appear asking you to confirm that you’d like to publish the Trip.

6. Select Publish to save the Trip to the user database, or Close to cancel the action.

ReferencesUsing TRX WebOnce your item is published, the item and the details you added will be visible to you and other TRX users in the community.

Note: Once an item has been saved to the public community, it cannot be removed. Please verify that all attributes of your Trip are accurate and describe any safety concerns before publishing a Trip.

Searching for a Trail, Trip, or POI

To search for a Trail, Trip, or POI on the homepage:

1. Select Trails, Trips, or one or more POIs from the Search function at the top of the page.

Note: You cannot search for POIs while searching for Trails or Trips. You can search Trails and Trips at the same time, or searching for more than one type of POI at the same time.

2. Type a custom search term in the Find text box, if desired.

3. Type a location in the Near text box (e.g. San Dimas, Santa Clara, Baldy, etc.).

4. Tap to search.

The Map will populate with results that match your search. If you selected Trips or Trails, they will appear on the map highlighted in red.

Tap on the Trail, Trip, or POI that you’re interested in to view detailed information:

Note: Some Trips and Trails will list a warning that states: “This is a publicly shared trail that has not been verified for safety. Drive at your own risk!”. Please heed this warning and review the details of the Trip or Trail to decide whether or not it’s safe for you or your vehicle.

Report Issues with a Trip or Trail

If necessary, you can report issues with a Trip or Trail. To do this, simply:

1. Select Report a Problem on the Trip or Trail details to open a new window.

ReferencesUsing TRX Web2. Select the appropriate options:

• The trail rating/trail specifications are wrong

• This published trail contains offensive or abusive language

• The trail path is incomplete or incorrect

3. Enter detailed notes about Trip or Trail issues in the text box, if necessary.

4. Select Submit to finish reporting a problem, or Close to cancel the action.

Save an Item to Your Wish List

To save a Trip, Trail, or POI from your search results to your Wish List:

1. Select to the right of the Trip/Trail/POI pop-up on the Map. A new window will appear:

2. Select Save to add the item to your Wish List, or Close to cancel the action.

The Trip, Trail, or POI will be instantly added to your Wish List.

Connect Social Media Accounts

You can also connect your Twitter and Instagram accounts to your TRX Web account profile if you haven’t already done so on your TRX7 device.

To connect your Twitter and Instagram accounts:

1. Select Profile at the top right corner of the screen.

2. Select either the grayed-out Twitter or Instagram icon. You will be redirected to the Twitter or Instagram login page.

3. Enter your Twitter or Instagram login information, or create a new account for use with your TRX journal.

Once you’ve successfully linked any of these social media accounts to your TRX account, the icon of that social network will appear in light blue instead of gray.

ReferencesUsing TRX WebUpload GPX Files

You can upload properly formatted GPS exchange format XML (GPX) files to your TRX Web account.

A GPX file can contain one or multiple routes, tracks, or Waypoints with attributes such as name, description, etc. TRX Web imports the GPX filename as the Trip name, but you can change the name.

To upload a GPX file:

1. Select .

2. Select the GPX file you wish to upload from your computer.

3. Select Open (on a PC) or Choose (on a Mac) to upload the file to your TRX Web account.

4. Rate and add attributes to the Trail with the same selections as if you’re adding your own Trail.

5. Select Review to publish the Trail for use by the TRX community.

Add a New Trip

You can add a new Trip to your account profile right from your TRX Web homepage simply by selecting:

A new Trip will be added to your Log. You can right click anywhere on the Map to add a Waypoint or a Trail in the order that you intend to ride them.

Section TitleWarrantyMagellan Limited Warranty

All Magellan global positioning system (GPS) receivers are navigation aids, and are not intended to replace other methods of navigation. The purchaser is advised to perform careful position charting and use good judgment. READ THE USER GUIDE CAREFULLY BEFORE USING THE PRODUCT.

1. MAGELLAN WARRANTY

(a) MiTAC Digital Corp. (“Magellan”) warrants its GPS receivers and hardware accessories to be free from defects in material and workmanship and will conform to its published specifications for the product for a period of one year from the date of original purchase. THIS WARRANTY APPLIES ONLY TO THE ORIGINAL CONSUMER PURCHASER OF THIS PRODUCT.

(b) In the event of a defect, Magellan will, at its discretion, repair or replace the hardware product with a product of like kind or quality, which may be new or reconditioned, with no charge to the purchaser for parts or labor. Magellan’s limit of liability under the limited warranty shall be the actual cash value of the product at the time the purchaser returns the product to Magellan for repair less a reasonable amount for usage, as determined by Magellan in its sole discretion. The repaired or replaced product will be warranted for 90 days from the date of return shipment, or for the balance of the original warranty, whichever is longer.

(c) Magellan warrants that software products or software included in hardware products will be free from defects in the media for a period of 30 days from the date of shipment and will substantially conform to the then current user documentation provided with the software (including updates thereto). Magellan’s sole obligation shall be the correction or replacement of the media or the software so that it will substantially conform to the then- current user documentation. Magellan does not warrant the software will meet purchaser’s requirements or that its operation will be uninterrupted, error-free or virus-free. The purchaser assumes the entire risk of using the software.

2. PURCHASER’S REMEDY

PURCHASER’S EXCLUSIVE REMEDY UNDER THIS WRITTEN WARRANTY OR ANY IMPLIED WARRANTY SHALL BE LIMITED TO THE REPAIR OR REPLACEMENT, AT MAGELLAN’S OPTION, OF ANY DEFECTIVE PART OF THE RECEIVER OR ACCESSORIES WHICH ARE COVERED BY THIS WARRANTY. REPAIRS UNDER THIS WARRANTY SHALL ONLY BE MADE AT AN AUTHORIZED MAGELLAN SERVICE CENTER. ANY REPAIRS BY A SERVICE CENTER NOT AUTHORIZED BY MAGELLAN WILL VOID THIS WARRANTY.

3. PURCHASER’S DUTIES

For repair or replacement on a Magellan product the purchaser must obtain a

Section TitleWarrantyReturn Materials Authorization (RMA) number from Magellan Technical Sup-port or by submitting a repair request through our website at www.magel-lanGPS.com, prior to shipping. The pur-chaser must return the product postpaid with a copy of the original sales receipt, purchaser’s return address and the RMA number clearly printed on the outside of the package to the Authorized Magel-lan Service Center address provided by Magellan with the RMA number. Magel-lan reserves the right to refuse to pro-vide service free-of-charge if the sales receipt is not provided or if the informa-tion contained in it is incomplete or il-legible or if the serial number has been altered or removed. Magellan will not be responsible for any losses or damage to the product incurred while the product is in transit or is being shipped for repair. Insurance is recommended. Magellan recommends the use of a trackable ship-ping method such as UPS or FedEx when returning a product for service.

4. LIMITATION OF IMPLIED WARRANTIES

Except as set forth in item 1 above, all other expressed or implied warran-ties, including those of fitness for any particular purpose or merchantability, are hereby disclaimed AND IF APPLI-CABLE, IMPLIED WARRANTIES UNDER ARTICLE 35 OF THE UNITED NATIONS CONVENTION ON CONTRACTS FOR THE INTERNATIONAL SALE OF GOODS. Some national, state, or local laws do not allow limitations on implied warranty on how

long an implied warranty lasts, so the above limitation may not apply to you.

5. EXCLUSIONS

The following are excluded from the war-ranty coverage:

(a) periodic maintenance and repair or replacement of parts due to normal wear and tear;

(b) batteries;

(c) finishes;

(d) installations or defects resulting from installation;

(e) any damage caused by (i) shipping, misuse, abuse, negligence, tampering, moisture, liquids, proximity or exposure to heat, or improper use; (ii) disasters such as fire, flood, wind, and lightning; (iii) unauthorized attachments or modifi-cation;

(f) service performed or attempted by anyone other than an authorized Magel-lan Service Center;

(g) any product, components or parts not manufactured by Magellan,

(h) that the receiver will be free from any claim for infringement of any patent, trademark, copyright or other proprietary right, including trade secrets

(i) any damage due to accident, resulting from inaccurate satellite transmissions. Inaccurate transmissions can occur due to changes in the position, health or ge-ometry of a satellite or modifications to the receiver that may be required due to

Section TitleWarrantyany change in the GPS.

(Note: Magellan GPS receivers use GPS or GPS+GLONASS to obtain position, velocity and time information. GPS is operated by the U.S. Government and GLONASS is the Global Navigation Satellite System of the Russian Federation, which are solely responsible for the accuracy and maintenance of their systems. Certain conditions can cause inaccuracies which could require modifications to the receiver. Examples of such conditions include but are not limited to changes in the GPS or GLONASS transmission.).

The opening, dismantling or repairing of this product by anyone other than an authorized Magellan Service Center will void this warranty.

6. EXCLUSION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES

(a) MAGELLAN SHALL NOT BE LIABLE TO PURCHASER

(b) OR ANY OTHER PERSON FOR ANY INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES WHATSOEVER, INCLUDING BUT NOT LIMITED TO LOST PROFITS, DAMAGES ARISING FROM A DELAY OR LOSS OF USE, OR OUT OF THE BREACH OF THIS WARRANTY OR ANY IMPLIED WARRANTY EVEN IF CAUSED BY THE NEGLIGENCE OR ANOTHER FAULT OF MAGELLAN OR OUT OF THE NEGLIGENT USAGE OF THE PRODUCT. IN NO EVENT WILL MAGELLAN BE HELD RESPONSIBLE FOR SUCH DAMAGES, EVEN IF

MAGELLAN HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

(c) Some national, state, or local laws do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.

7. COMPLETE AGREEMENT

(a) This written warranty is the complete, final and exclusive agreement between Magellan and the purchaser with respect to the quality of performance of the goods and any and all warranties and representations. THIS WARRANTY SETS FORTH ALL OF MAGELLAN’S RESPONSIBILITIES REGARDING THIS PRODUCT. THIS WARRANTY GIVES YOU SPECIFIC RIGHTS. YOU MAY HAVE OTHER RIGHTS WHICH VARY FROM LOCALITY TO LOCALITY AND CERTAIN LIMITATIONS CONTAINED IN THIS WARRANTY MAY NOT APPLY TO YOU.

(b) If any part of this limited warranty is held to be invalid or unenforceable, the remainder of the limited warranty shall nonetheless remain in full force and effect.

This limited warranty is governed by the laws of the State of California, without reference to its conflict of law provisions or the U.N. Convention on Contracts for the International Sale of Goods, and shall benefit Magellan, its successors and assigns. This warranty does not affect the consumer’s statutory rights under applicable laws in force in their locality, nor the customer’s rights against the

Section TitleWarrantydealer arising from their sales/purchase contract.

For further information concerning this limited warranty, please visit Magellan’s website www.magellangps.com or con-tact:

MiTAC Digital Corp. 471 El Camino Real, Santa Clara, CA 95050, USA

USA & Canada: 800-707-9971

Mexico: 866-310-7223

Section TitleTechnical SupportNeed Technical Support?

If you need technical support for your Magellan device, you should first go to www.magellangps.com/support for answers to most questions.

If you can’t find a solution there, you can contact Magellan Technical Support directly by email at support.us@cs.magellangps.com or call 800-707-9971.

Connect with us @MagellanGPS

N496(x) SeriesUser Manual

1

Table of contents

Your device at a glance ...............................................................................2

Charging the battery ...................................................................................3

Turning the device ON and OFF ................................................................4Sleep mode ..................................................................................................4Airplane mode ............................................................................................. 5

Installing a memory card ...........................................................................5

Connecting to a computer .........................................................................6

Connecting a USB device ............................................................................6

Mounting the device ...................................................................................6

Navigating on the screen ............................................................................ 7

Home screen ................................................................................................8

Customizing your device ............................................................................9WLAN connection ......................................................................................9Bluetooth connection ................................................................................9

Caring for your device ...............................................................................10Troubleshooting ........................................................................................ 10Caring for your device ...............................................................................11

Regulatory information ............................................................................ 12FCC .............................................................................................................. 12IC .................................................................................................................. 13Safety precautions .................................................................................... 14

2

Your device at a glance

Note: Depending upon the specific model purchased, the color and look of your device and accessories may not exactly match the graphics shown in this document.

❶ Microphone

❷ Light sensor*

❸ Touch screen

❹ Speaker*

❺ Power button

❻ Volume buttons

❼ Mute button

❽ Camera button*

❾ P1/Back button

❿ P2/Home button

⓫ P3/Menu button

⓬ Cradle screws*

⓭ Speaker*

⓮ Dock connector*

⓯ Mini-USB connector

⓰ NFC sensor*

⓱ Headphone jack

⓲ USB port

⓳ Memory card slot

⓴ Cover latch

*For selected models only

3

Charging the batteryNote: Use only the charger supplied with your device. Use of another type of charger will result in malfunction and/or danger.

When charging the battery for the very first time, you should charge it for at least 8 hours (using the AC charger) with your device turned off.1. Push the tap outwards, plug the converter to the AC charger and then push the tap

inwards to lock the converter in place (❶).2. Open the connector cover on your device and connect the charger cable to the mini-

USB connector (❷).3. Plug the AC charger into a wall outlet (❸).

CAUTION: For optimal performance of the lithium battery: y Do not charge the battery where the temperature is high (e.g. in direct sunlight). y Recharge the battery when it is nearly discharged. When recharging, make sure that the battery is fully

charged. Doing so can extend the battery life. y If you will not use the product for a long period of time (over one month) or find the discharge/

recharge time has been shortened, be sure to fully discharge the battery first before recharging it. You are also advised to fully discharge and recharge the battery once every 1~2 months.

y Failure to follow the battery usage instructions could cause damage to your device, battery and even bodily injury or property damage and will void the warranty.

4

Turning the device ON and OFF1. Press the Power button on the right side of the device to turn on your device. Wait for

the boot screen to display.2. The Home screen will display and the device is in Lock mode by default. Drag the Lock

icon ( ) to the right. The device is ready for use.

3. To turn off the devide, press and hold the Power button until the option window displays. Then tap Power off OK.Note: You can also choose to restart the device by selecting Restart from the option window.

Sleep modeYour device will automatically switch off the screen after 1 minute (by default) of inactivity. You can manually switch off the screen by pressing the Power button briefly.To resume the screen, press the Power button briefly and then unlock the device by dragging the Lock icon ( ) to the right.

To change the settings, tap on the desktop Settings Display Sleep.

5

Airplane modeWhen you are in an airplane or in the area where data transferring is not allowed, enable Airplane mode. You will be able to use many of your device’s applications (such as playing games or listening music), but all wireless radios, including wireless network (WLAN) and Bluetooth, on the device are turned off – it cannot send or receive data.To enable Airplane mode: press and hold the Power button until the option window displays. Then tap Airplane mode. The icon in the status bar indicates that Airplane mode is on.

To disable Airplane mode: tap on the desktop Settings More, and then cancel the selection in Airplane mode.

Installing a memory cardCAUTION: Do not apply pressure to the center of the memory card.

Slide the cover latch to open the cover on the left side of the device to locate the memory card slot. Noting the card orientation, hold the card (MicroSD) by the edges and gently insert it into the slot.To remove a card, first unmount it from the device by tapping on the desktop Settings Storage Unmount SD Card OK. Then gently push the top edge of the card inwards to release it, and pull it out of the slot.Note: Inserting the card in the reverse direction may cause damage.

Note: The manufacturer does not guarantee the product’s compatibilities with the storage cards from all manufacturers.

Note: If you encounter access problems with your memory card, please visit the website http://www.sdcard.org/consumers/formatter_3/ and use the "SD Formatter 3.0 for SD/SDHC/SDXC" tool to format your memory card.

6

Connecting to a computerConnect the mini-USB end of the USB cable to your device and the other end to a USB port of your computer.Note: When connected to the computer, your device will not be charged. When data synchronization is in progress, your device will consume instead of charging battery power.

Connecting a USB deviceYou can connect an external USB storage (such as a USB flash drive) as an additional storage for the system.Slide the cover latch to open the cover on the left side of the device to locate USB port.

Mounting the deviceDepending on your model, a cradle and mount may be provided for your device. Follow the illustrations to mount and detach your device.

1

7

2 3

Navigating on the screenTo operate your device, touch the screen with your finger.You can perform the following actions:

y Tap: Touch the screen once with your finger to open items or select onscreen buttons or options.

y Tap and hold: Tap and hold on the desired item to open the pop-up menu that contains the available options for the item (for example, the Copy/Move/Rename options for a file in File Manager).

y Drag: Tap and hold on the item and then move it to the target position without releasing your finger.

y Slide: Drag your finger vertically or horizontally across the screen. y Drag to the left/right to switch to the next/previous item on the list. y Drag to the top/bottom to scroll up/down the screen.

Note: Not all slide gestures are applicable to all applications.

y Multi-touch gestures: Move your fingers apart or together on the screen to zoom in or out while viewing a picture or a web page.

8

Note: Not all multi-touch gestures are applicable to all applications.

y Rotating the screen: For most applications, you can automatically change the screen orientation, from portrait to landscape and vise versa, by turning the device sideways.Note: Rotating the screen is not applicable to all applications.

Home screenThe Home screen is your starting place for tasks, providing quick access to frequently used applications and settings.To display the Home screen, press the P2/Home button on the device or tap at any time.

Status Bar

Quick Launcher

Shortcuts/widgets

DesktopAll Apps button

Soft keys

Back

Home

Recent Apps

The soft keys may be in hidden mode at times. Simply tap where the keys are located to bring out the keys again.

9

Customizing your deviceYou can customise the device through the Settings menu, including personalizing the Home screen, changing the display and sound settings, configuring the connection settings, and more.To access the Settings menu, tap on the desktop Settings.

WLAN connection1. Tap on the desktop Settings.2. In WIFI, tap the OFF/ON switch to turn WLAN on. The device will automatically scan

for available wireless networks.3. Tap WIFI to display the network names and security settings of the detected WLAN

networks.4. Tap a WLAN network to connect.5. If you select an open network, you will be automatically connected to the network.

If you select a network that is secured with WEP, enter the key and then tap Connect.6. When your device is connected to a wireless network, the WLAN icon ( ) will appear

in the status bar indicating the signal strength (number of bands that light up).

Bluetooth connectionTo pair a Bluetooth device for sharing data:

1. Tap on the desktop Settings.

2. In Bluetooth, tap the OFF/ON switch to turn Bluetooth on. The device will automatically scan for available Bluetooth devices. Note: By default, your device is not in visible mode when Bluetooth is turned on. If you need to enter visible mode: tap Bluetooth and then tap your device name. The default visibility timeout is 2 minutes.

3. Tap Bluetooth to display the list of in-range Bluetooth devices.Note: You can tap SEARCH FOR DEVICES to do a new scanning.

10

4. Tap a device from the list to initiate pairing.5. On your device, the passkey is displayed. On the other device, enter the same passkey

and then tap Pair. Then tap Pair on your device to confirm pairing if necessary.

Caring for your deviceTroubleshootingNote: If you encounter a problem you cannot solve, contact an authorised service centre for assistance.

Power does not switch on when using battery power.

y The remaining battery power may be too low to run your device. Charge the battery.

Screen responds slowly.

y Make sure that your device is not running out of battery power. If the problem still persists, restart your device.

Screen freezes.

y Restart your device.

Screen is hard to read.

y Make sure that the backlight of the display is set to a high-enough brightness.

Cannot establish a connection with a computer.

y Make sure that your device and your computer are both switched on before trying to establish a connection.

y Make sure that the cable is securely plugged into the USB port on your computer and on your device. Connect the USB cable directly to your computer—do not run the cable through a USB hub.

y Restart your device before connecting the cable. Always disconnect your device before you restart your computer.

11

Caring for your deviceTaking good care of your device will ensure trouble-free operation and reduce the risk of damage to your device.

y Keep your device away from excessive moisture and extreme temperatures. y Avoid exposing your device to direct sunlight or strong ultraviolet light for extended

periods of time. y Do not place anything on top of your device or drop objects on your device. y Do not drop your device or subject it to severe shock. y Do not subject your device to sudden and severe temperature changes. This could

cause moisture condensation inside the unit, which could damage your device. In the event of moisture condensation, allow the device to dry out completely before use.

y The screen surface can easily be scratched. Avoid touching it with sharp objects. Non-adhesive generic screen protectors designed specifically for use on portable devices with LCD panels may be used to help protect the screen from minor scratches.

y Never clean your device with it powered on. Use a soft, lint-free cloth to wipe the screen and the exterior of your device.

y Do not use paper towels to clean the screen. y Never attempt to disassemble, repair or make any modifications to your device.

Disassembly, modification or any attempt at repair could cause damage to your device and even bodily injury or property damage and will void any warranty.

y Do not store or carry flammable liquids, gases or explosive materials in the same compartment as your device, its parts or accessories.

y To discourage theft, do not leave the device and accessories in plain view in an unattended vehicle.

y Do not expose the device to extreme heat or direct sunlight for prolonged periods. Overheating may damage the device.

12

Regulatory information y For regulatory identification purposes, the product series is assigned a model number

of N496(x) (the optional "x" representing a potential model in the product series). y Wi-Fi 5G Band 1 is for indoor use only.

FCC

Federal Communication Commission Interference StatementThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

y Reorient or relocate the receiving antenna. y Increase the separation between the equipment and receiver. y Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. y Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: y Any changes or modifications not expressly approved by the party responsible for compliance could void the user's

authority to operate this equipment. y This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Radiation Exposure Statement:This device meets the government’s requirements for exposure to radio waves.This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government.The exposure standard for wireless device employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6W/kg. *Tests for SAR are conducted using standard operating positions accepted by the FCC with the device transmitting at its highest certified power level in all tested frequency bands.The country code selection is for non-US model only and is not available to all US model. Per FCC regulation, all WiFi product marketed in US must fixed to US operation channels only.

13

IC y This device complies with Industry Canada

license-exempt RSS standard(s). Operation is subject to the following two conditions:

y Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes:

y This device may not cause interference. y L'appareil ne doit pas produire de brouillage. y This device must accept any interference,

including interference that may cause undesired operation of the device.

y L'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

y This Class B digital apparatus complies with Canadian ICES-003.

y Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

y This device complies with RSS-310 of Industry Canada. Operation is subject to the condition that this device does not cause harmful interference.

y Cet appareil est conforme à la norme RSS-310 d'Industrie Canada. L'opération est soumise à la condition que cet appareil ne provoque aucune interférence nuisible.

y This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter, except tested built-in radios.

y Cet appareil et son antenne ne doivent pas être situés ou fonctionner en conjonction avec une autre antenne ou un autre émetteur, exception faites des radios intégrées qui ont été testées.

y The County Code Selection feature is disabled for products marketed in the US/ Canada.

y La fonction de sélection de l'indicatif du pays est désactivée pour les produits commercialisés aux États-Unis et au Canada.

Radiation Exposure Statement:The product comply with the Canada portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available.

Déclaration d'exposition aux radiations:Le produit est conforme aux limites d'exposition pour les appareils portables RF pour les Etats-Unis et le Canada établies pour un environnement non contrôlé. Le produit est sûr pour un fonctionnement tel que décrit dans ce manuel. La réduction aux expositions RF peut être augmentée si l'appareil peut être conservé aussi loin que possible du corps de l'utilisateur ou que le dispositif est réglé sur la puissance de sortie la plus faible si une telle fonction est disponible.

Caution: y The device for operation in the band 5150-5250

MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems.

Avertissement: y Les dispositifs fonctionnant dans la bande 5150-5250 MHz

sont réservés uniquement pour une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux.

y The maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall comply with the e.i.r.p. limit.

y Le gain maximal d’antenne permis pour les dispositifs utilisant les bandes 5250-5350 MHz et 5470-5725 MHz doit se conformer à la limite de p.i.r.e.

y The maximum antenna gain permitted for devices in the band 5725-5825 MHz shall comply with the e.i.r.p. limits specified for point-to-point and non point-to-point operation as appropriate.

y Le gain maximal d’antenne permis (pour les dispositifs utilisant la bande 5725-5825 MHz) doit se conformer à la limite de p.i.r.e. spécifiée pour l’exploitation point à point et non point à point, selon le cas.

14

y The worst-case tilt angle(s) necessary to remain compliant with the e.i.r.p. elevation mask requirement set forth in Section 6.2.2(3) shall be clearly indicated.

y Les pires angles d’inclinaison nécessaires pour rester conforme à l’exigence de la p.i.r.e. applicable au masque d’élévation, et énoncée à la section 6.2.2 3), doivent être clairement indiqués.

y Users should also be advised that high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices.

y De plus, les utilisateurs devraient aussi être avisés que les utilisateurs de radars de haute puissance sont désignés utilisateurs principaux (c.-à-d., qu’ils ont la priorité) pour les bandes 5250-5350 MHz et 5650-5850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL.

Safety precautions

About charging

y Use only the charger supplied with your device. Use of another type of charger will result in malfunction and/or danger.

y This product is intended to be supplied by a LISTED Power Unit marked with “LPS”, “Limited Power Source” and output rated + 5 V dc / 2.0 A.

y Use a specified battery in the equipment.

About the charger

y Do not use the charger in a high moisture environment. Never touch the charger when your hands or feet are wet.

y Allow adequate ventilation around the charger when using it to operate the device or charge the battery. Do not cover the charger with paper or other objects that will reduce cooling. Do not use the charger while it is inside a carrying case.

y Connect the charger to a proper power source. The voltage requirements are found on the product case and/or packaging.

y Do not use the charger if the cord becomes damaged. y Do not attempt to service the unit. There are no serviceable parts inside. Replace the

unit if it is damaged or exposed to excess moisture.

15

About the battery

y Use a specified battery in the equipment. y This unit contains a non-replaceable internal Lithium Ion battery. The battery can burst

or explode, releasing hazardous chemicals. To reduce the risk of fire or burns, do not disassemble, crush, puncture, or dispose of in fire or water.

y Important instructions (for service personnel only) y Risk of explosion if battery is replaced by an incorrect type. Dispose of used

batteries according to the instructions. y Replace only with the same or equivalent type recommended by the manufacturer. y The battery must be recycled or disposed of properly. y Use the battery only in the specified equipment.

16

Revision: R00 (September, 2015)Trademarks All brand and product names are trademarks or registered trademarks of their respective companies.Disclaimer Specifications and documents are subject to change without notice.Notes Not all models are available in all regions. Depending upon the specific model purchased, the color and look of your device and accessories may not exactly match the graphics shown in this document. The screenshots and other presentations shown in this document are for reference only.