DT test report

Drive Test ReportOf CMPAK GSM 900 Network 3535near 11 number chungi Multan SITE NAME: 3535near 11 number chungi Multan PHASE: 5 (Expansion) REGION: C3AREA: MultanDRIVE TEST DATE: 23/10/20131. Executive Summary

SITE INFO:Sr.AreaSite NameAction TakenTimelineStatusResponsibility

1 Multan3535 near 11 number chungi MultanDrive Test11:00 to 16:30Test ModeAasim shahzad

Site information:Site IDCell NameLongitudeLatitudeTower HeightAntenna HeightAzimuthM-TiltE-TiltAntenna ManufacturerAntenna Model

353525351 71.492

30.184

25m15m6025 TDJTDJ182018DE65F

3535 25352 25m15m23025 TDJTDJ182018DE65F

353525353 25m15m32025 TDJTDJ182018DE65F

Frequency:CELL IDTRX ConfigurationBCCHBSICHSNMAMAIOCGI

Hard warePlanBSC

2535122210123145987, 988, 989,.,1003 041004301325351

2535222210212445987, 988, 989,.,1003241004301325352

2535322210142245987, 988, 989,.,1003441004301325353

This site covers the urban area. The KPI of this site are good. The coverage is normal.1.1) Main KPIOperatorCoverage RateRx QualHOSRCSSRCDRMean Delay time of Call establishment

CMPAK99.16%95.14%100.00%100.00%0.00%0.00s

1.2) Detailed dataRXLEV SUB (dedicated)

Values (dBm)0 to -60-60to-70-70to-80-80to-90-90to-100-100to-110

Samples7022408740718451360

Per %43.450281525.289276725.19027295.228636840.841532080

RXLEV Full Idle

Values (dBm)0 to -60-60to-70-70to-80-80to-90-90to-100-100to-110

Samples14750139120000

Per %91.26910468.607140650.12375472000

RXQUAL

Values01234567

Samples12522441366437379471371380

Per (%)81.49 2.87 2.38 2.84 2.47 3.07 2.41 2.47

CSSR AND CDR

OperatorCall attempt timesCall successful timesBlocked timesDrop times

CMPAK 7700

HOSR

OperatorHO successful timesHO attempt timesHO failure times

CMPAK660

2. INTRODUCTION

2.1. TESTING PLAN

2.1.1. TESTING NETWORKS

Operators to be tested: CMPAK2.1.2. TESTING TIME

Drive test time: 11:00 to 16:302.1.3. CITY and ROUTE

Approved routes to be attached and tested covering all cells and cell boundaries within cluster. All first tier neighbors must well test as per planned route.

2.1.4. TESTING PERSONALS

LCC team:Aasim Shahzad2.1.5. TESTING EQUIPMENT

Drive test was performed with two mobiles.One mobile was on call mode.One mobile was on idle mode.2.2. TESTING METHOD

2.2.1 TEST MODECall Duration: longCall Interval: 5sec

Retry in case of call failure or congestion will be 20s

Note: Calls were made from MS to MS and to the same operator calling and called numbers.2.3. KPI TO BE MONITIRED

2.3.1. CSSR

Definition: CSSR=Call successful times/Call attempt times*100%

Note:

Call attempt times: Only if message channel request and CM service request appeared simultaneously, then can be judge as a call attempt.Call successful times: After call attempt start, either message connect or message connect acknowledge appeared, then can be judged as a call successful.CSSR must calculated by calling MS.

2.3.2. CDR

Definition:CDR=Call drop times/Call successful times*100%

Note:

1)Call drop times: During a call, if message Disconnect or Channel Release appeared, then can be considered as a normal call; otherwise, neither of them appeared, and the state of MS also change from dedicate to idle, then can be judged as a drop.2) CDR must calculate by calling MS and called MS.

3) CDR= (calling drop+called drop)/ (calling successful +called successful)*100%2.3.3 Coverage rate

Definition:

Coverage Rate = >=-90dBm Sample numbers/Total Sample numbers100

Note:

1) Coverage Rate must calculate by calling MS and called MS.

2) Sample number=100s dedicate mode + 20s idle mode2.3.4 RXQUAL

Definition:

RXQUAL= [RxQual0 LevelRxQual1 LevelRxQual2 LevelRxQual3 Level]1[RxQual4 LevelRxQual5 Level+RxQual6 Level]0.7

Note:

1) Sample number=calling MS + called MS2.3.5 HOSR

Definition: HOSR=Ho successful times/Ho attempt times*100%2.3.6 Mean Delay time of Call establishment

Definition:

The time difference between the latest channel request message and alerting message. (Calculate it by frame number)Note:

1) Calculate by calling MS.2) The value is the average value of all calls.

3. Test results and analysis

3.1 AREA DEFINITION

3.2 COVERAGE3.2.1 COVERAGE MAP(RX Level Sub)

3.2.2 COVERAGE MAP ( RX Level FULL IDLE)

3.3RXQUALMAP

3.4 SQI MAP

Comments: when MS in idle mode, the SQI default as 0 or no display.3.5 TA MAP

3.6 C/I Worst MAP

Comments: when MS in idle mode, the C/I worst default as 0 or no display.3.7 CELL ID MAP

3.8 BCCH MAP

3.9 BCCH MAP (IDLE)

3.9 CQT TESTCell IDTRXRx LevelVoiceTRx State

BCCH 49OKNormal

25351MAIO-0 48OKNormal

25352BCCH-42OKNormal

MAIO-2-49OKNormal

25353BCCH-54OKNormal

MAIO-4-45OKNormal

3.10 Remarks All possible routes are covered during DT.

All DT KPIs were achieved.

Site is performing normal as per implemented parameters.PAGE 3