Examen Del Modulo 1
-
Upload
hugo-saucedo-hernandez -
Category
Documents
-
view
125 -
download
0
Transcript of Examen Del Modulo 1
If a router cannot find a valid configuration file during the startup sequence, what will occur?The startup sequence will reset.
The router will prompt the user for a response to enter setup mode.
The startup sequence will halt until a valid configuration file is acquired.
The router will generate a default configuration file based on the last valid configuration.
The router will monitor local traffic to determine routing protocol configuration requirements.
2 Passwords can be used to restrict access to all or parts of the Cisco IOS. Select the modes and interfaces that can be protected with passwords. (Choose three.)
VTY interface
console interface
Ethernet interface
secret EXEC mode
privileged EXEC mode
router configuration mode
3 What header address information does a router change in the information it receives from an attached Ethernet interface before information is transmitted out another interface?
only the Layer 2 source address
only the Layer 2 destination address
only the Layer 3 source address
only the Layer 3 destination address
the Layer 2 source and destination address
the Layer 3 source and destination address
4 What three processes does a router execute when it receives a packet from one network that is destined for another network? (Choose three.)
decapsulates the Layer 3 packet by stripping off the Layer 2 frame header
uses the destination MAC Address in the IP Header to look up the next-hop address in the routing table
leaves the Layer 2 frame header intact when decapsulating the Layer 3 packet
uses the destination IP Address in the IP header to look up the next-hop address in the routing table
encapsulates the Layer 3 packet into the new Layer 2 frame and forwards it out the exit interface
encapsulates the Layer 3 packet into a special Layer 1 frame and forwards it to the exit interface
5
Refer to the exhibit. Host A pings host B. When R4 accepts the ping into the Ethernet interface, what two pieces
of header information are included? (Choose two.)source IP address: 192.168.10.129
source IP address: BBBB.3333.5677
source MAC address: 5555.AAAA.6666
destination IP address: 192.168.10.33
destination IP address: 192.168.10.134
destination MAC address: 9999.DADC.1234
6
Refer to the exhibit. What can be concluded from the routing table output in the exhibit? (Choose two.)This router only has two interfaces.
The router interfaces are not operational yet.
This router is configured to forward packets to remote networks.The FastEthernet0/0 and Serial0/0/0 interfaces of this router were configured with an IP address and the no shutdown command.An IP packet received by this router with a destination address of 198.18.9.1 will be forwarded out of the Serial0/0/0 interface.
7
Refer to the exhibit. The network administrator has configured the router with the interface IP addresses shown for the directly connected networks. Pings from the router to hosts on the connected networks or pings between router interfaces are not working. What is the most likely problem?
The destination networks do not exist.
The IP addresses on the router interfaces must be configured as network addresses and not host addresses.
The interfaces must be enabled with the no shutdown command.
Each interface must be configured with the clock rate command.
8 From what location can a router load the Cisco IOS during the boot process? (Choose two.)RAM
TFTP server
NVRAM
setup routine
Flash memory
terminal
9 What is the default sequence for loading the configuration file?NVRAM, FLASH, ROM
FLASH, TFTP,CONSOLE
NVRAM, TFTP, CONSOLE
FLASH, TFTP, ROM
10
Refer to the exhibit. The frame shown in the exhibit was received by the router. The router interfaces are operational. How will the router process this frame? (Choose two.)
The router will change the source and destination IP address in the packet before forwarding the frame.
The router will change the frame type to one supported by the WAN link before forwarding the frame.
The router will use the destination MAC address to determine which interface to forward the packet.The router will look up the MAC address of the S0/0/0 interface in the ARP table and add it to the frame before forwarding.The frame was received on the Fa0/0 interface of the router and will be switched to the S0/0/0 interface.
The frame was received on the S0/0/0 interface of the router and will be switched to the Fa0/0 interface.
11 Which of the following is the correct flow of routines for a router startup?load bootstrap, load IOS, apply configuration
load bootstrap, apply configuration, load IOS
load IOS, load bootstrap, apply configuration, check hardware
check hardware, apply configuration, load bootstrap, load IOS
12 The network administrator needs to connect two routers directly via their FastEthernet ports. What cable should the network administrator use?
straight-through
rollover
cross-over
serial
13 What information about the router and its startup process can be gathered from the output of the show version command? (Choose three.)
the last restart method
the command buffer contents
the amount of NVRAM and FLASH used
the configuration register settings
the location from where the IOS loaded
14
Which interfaces in the exhibit could be used for a leased line WAN connection? (Choose two.)1
2
3
4
5
6
15
Refer to the exhibit. What can be concluded from the output of the running-configuration of a router?The passwords are encrypted.
The current configuration was saved to NVRAM.
The configuration that is shown will be the one used on the next reboot.
The commands that are displayed determine the current operation of the router.16 Which two statements describe characteristics of load balancing? (Choose two.)
Load balancing occurs when a router sends the same packet to different destination networks.
Load balancing occurs when the same number of packets are sent over static and dynamic routes.
Load balancing allows a router to forward packets over multiple paths to the same destination network.
Unequal cost load balancing is supported by EIGRP.
If multiple paths with different metrics to a destinations exist, the router cannot support load balancing.
17 What is the outcome of entering these commands?R1(config)# line vty 0 4R1(config-line)# password check123R1(config-line)# login
ensures that a password is entered before entering user EXEC mode
sets the password to be used for connecting to this router via Telnet
requires check123 to be entered before the configuration can be saved
creates a local user account for logging in to a router or switch
18 Which are functions of a router? (Choose three.)packet switching
extension of network segments
segmentation of broadcast domains
selection of best path based on logical addressing
selection of best path based on physical addressing
19
Refer to the exhibit. After host 2 is connected to the switch on the LAN, host 2 is unable to communicate with host 1. What is the cause of this problem?
The subnet mask of host 2 is incorrect.
Host 1 and host 2 are on different networks.
The switch needs an IP address that is not configured.
The router LAN interface and host 1 are on different networks.
The IP address of host 1 is on a different network than is the LAN interface of the router.
20
Refer to the exhibit. All routers have a route in its routing table to each network that is shown in the exhibit. Default routes have not been issued on these routers. What can be concluded about how packets are forwarded in this network? (Choose two.)
If RouterC receives a packet that is destined for 10.5.1.1, it will be forwarded out interface Fa0/0.
If RouterA receives a packet that is destined for 192.168.3.146, it will be forwarded out interface S0/0/1.
If RouterB receives a packet that is destined for 10.5.27.15, it will be forwarded out interface S0/0/1.
If RouterB receives a packet that is destined for 172.20.255.1, it will be forwarded out interface S0/0/0.
If RouterC receives a packet that is destined for 192.16.5.101, it will be forwarded out interface S0/0/1.
21
The serial connection shown in the graphic needs to be configured. Which configuration commands must be made on the Sydney router to establish connectivity with the Melbourne site? (Choose three.)
Sydney(config-if)# ip address 201.100.53.2 255.255.255.0
Sydney(config-if)# no shutdown
Sydney(config-if)# ip address 201.100.53.1 255.255.255.224
Sydney(config-if)# clock rate 56000
Sydney(config-if)# ip host Melbourne 201.100.53.2
22 Which two statements correctly describe the components of a router? (Choose two.)RAM permanently stores the configuration file used during the boot sequence.
ROM contains diagnostics executed on hardware modules.
NVRAM stores a backup copy of the IOS used during the boot sequence.
Flash memory does not lose its contents during a reboot.
ROM contains the most current and most complete version of the IOS.
Flash contains boot system commands to identify the location of the IOS.
23 A network administrator has just entered new configurations into Router1. Which command should be executed to save configuration changes to NVRAM?
Router1# copy running-config flash
Router1(config)# copy running-config flash
Router1# copy running-config startup-config
Router1(config)# copy running-config startup-config
Router1# copy startup-config running-config
Router1(config)# copy startup-config running-config
Si un router no puede encontrar un archivo de configuración válido durante la secuencia de inicio, ¿qué ocurrirá?
La secuencia de inicio se restablecerá.
El router le pedirá al usuario una respuesta para acceder al modo de configuración.
La secuencia de inicio se detiene hasta que un archivo de configuración válida se adquiere.
El router genera un archivo de configuración basado en la configuración válida anterior.
El router controlar el tráfico local para determinar los requisitos de configuración de enrutamiento de protocolo.
2
Las contraseñas pueden ser usados para restringir el acceso a la totalidad o parte del Cisco IOS. Seleccione los
modos e interfaces que pueden ser protegidos con contraseñas. (Elija tres.)
VTY interfaz
interfaz de consola
Interfaz Ethernet
secreto modo EXEC
el modo EXEC privilegiado
el modo de configuración del router
3
¿Qué información de encabezado de dirección hace un cambio de router en la información que recibe de una
interfaz Ethernet conectada antes de transmitir información a otra interfaz?
sólo el nivel 2 la dirección de origen
sólo el nivel 2 la dirección de destino
sólo la capa 3 la dirección de origen
sólo la capa 3 la dirección de destino
la capa de 2 direcciones de origen y destino
la capa 3 direcciones de origen y destino
4
¿Qué tres procesos se ejecutan cuando un router recibe un paquete de una red que está destinado a otra red?
(Elija tres.)
desencapsula el paquete de capa 3 por el desprendimiento de la capa 2 cabecera de la trama
utiliza la dirección MAC de destino en el encabezado IP para buscar la dirección del siguiente salto en la tabla de
enrutamiento
sale de la Capa 2 cabecera de la trama intacta cuando desencapsula el paquete de capa 3
utiliza la dirección IP de destino en el encabezado IP para buscar la dirección del siguiente salto en la tabla de
enrutamiento
encapsula el paquete de Capa 3 en la nueva capa 2 frame y lo envía a la interfaz de salida
encapsula la capa 3 paquetes en una capa especial de un cuadro y lo reenvía a la interfaz de salida
5
Consulte la presentación. Una gran cantidad de host ping B. Cuando R4 acepta el ping en la interfaz de Ethernet,
lo que dos piezas de información de encabezado están incluidas? (Elija dos.)
dirección IP de origen: 192.168.10.129
dirección IP de origen: BBBB.3333.5677
dirección MAC de origen: 5555.AAAA.6666
dirección IP de destino: 192.168.10.33
dirección IP de destino: 192.168.10.134
dirección MAC de destino: 9999.DADC.1234
6
Consulte la presentación. ¿Qué puede concluirse de la salida de la tabla de enrutamiento en la exposición? (Elija
dos.)
Este router sólo tiene dos interfaces.
Las interfaces del router no están funcionando todavía.
Este router está configurado para reenviar paquetes a redes remotas.
El FastEthernet0 / 0 y Serial0/0/0 de este router se han configurado con una dirección IP y el comando no
shutdown.
Un paquete IP recibido por el router con una dirección de destino de 198.18.9.1 será enviado fuera de la interfaz
Serial0/0/0.
7
Consulte la presentación. El administrador de red ha configurado el router con la IP de la interfaz direcciones
indicadas para las redes conectadas directamente. Hace un ping desde el router a los hosts de las redes
conectadas o pings entre las interfaces del router no están funcionando. ¿Cuál es el problema más probable?
Las redes de destino no existe.
Las direcciones IP de las interfaces del router se debe configurar como direcciones de red y no las direcciones de
host.
Las interfaces deben estar habilitadas con el comando no shutdown.
Cada interfaz se debe configurar con el comando clock rate.
8
Desde qué lugar puede un router cargue el IOS de Cisco durante el proceso de arranque? (Elija dos.)
RAM
Servidor TFTP
NVRAM
configuración de la rutina
De memoria flash
terminal
9
¿Cuál es la secuencia por defecto para cargar el fichero de configuración?
NVRAM, FLASH, ROM
FLASH, TFTP, CONSOLA
NVRAM, TFTP, CONSOLA
FLASH, TFTP, ROM
10
Consulte la presentación. El marco que se muestra en la exposición fue recibido por el router. Las interfaces del
router están en funcionamiento. ¿De qué manera el router proceso de este marco? (Elija dos.)
El router va a cambiar la fuente y la dirección IP de destino del paquete antes de reenviar la trama.
El router va a cambiar el tipo de trama a uno apoyado por el enlace WAN antes de enviar la trama.
El router utiliza la dirección MAC de destino para determinar qué interfaz para enviar el paquete.
El router buscará la dirección MAC de la interfaz S0/0/0 en la tabla ARP y agregarlo a la estructura antes de
enviarlo.
El marco fue recibido en la interfaz Fa0 / 0 del router y se conmuta a la interfaz S0/0/0.
El marco fue recibido en la interfaz S0/0/0 del router y se conmuta a la interfaz Fa0 / 0.
11
¿Cuál de los siguientes es el flujo correcto de rutinas para un inicio del router?
de arranque de carga, la carga del IOS, aplicar la configuración
de arranque de carga, aplicar la configuración, cargar el IOS
carga de IOS, de arranque de carga, aplicar la configuración, verificar el hardware
verificar el hardware, aplicar la configuración, arranque de carga, la carga del IOS
12
El administrador de red necesita conectar dos routers directamente a través de sus puertos FastEthernet. ¿Qué
cable debe utilizar el administrador de la red?
straight-through
rollover
cross-over
de serie
13
¿Qué información sobre el router y su proceso de inicio se puede deducir de la salida del comando show version?
(Elija tres.)
el método de último reinicio
el contenido del búfer de comandos
la cantidad de NVRAM y FLASH utilizada
la configuración del registro de configuración
el lugar desde donde el IOS cargada
14
¿Qué interfaces en la exposición podrían ser utilizados para una línea dedicada de conexión WAN? (Elija dos.)
1
2
3
4
5
6
15
Consulte la presentación. ¿Qué se puede concluir de los resultados de la gestión de configuración de un router?
Las contraseñas están cifradas.
La configuración actual se ha guardado en la NVRAM.
La configuración que se muestra será la utilizada en el siguiente reinicio.
Los comandos que se muestran determinar el funcionamiento actual del router.
16
¿Qué dos afirmaciones describen las características de balanceo de carga? (Elija dos.)
El equilibrio de carga se produce cuando un router envía el mismo paquete a las redes de destino diferente.
El equilibrio de carga se produce cuando el mismo número de paquetes enviados a través de rutas estáticas y
dinámicas.
El equilibrio de carga permite que un router para enviar paquetes en varias rutas a la misma red de destino.
Equilibrar la carga de costos desiguales con el apoyo de EIGRP.
Si existen varias rutas con diferentes métricas a un destino existe, el router no puede soportar el balanceo de
carga.
17
¿Cuál es el resultado de introducir esos comandos?
R1 (config) # line vty 0 4
R1 (config-line) # password check123
R1 (config-line) # login
se asegura de que se introduzca una contraseña antes de entrar en el modo EXEC usuario
establece la contraseña que se utiliza para conectarse a este router a través de Telnet
requiere check123 a ser introducidos antes de la configuración se puede guardar
crea una cuenta de usuario local para poder conectarse a un router o switch
18
¿Cuáles son las funciones de un router? (Elija tres.)
de conmutación de paquetes
extensión de los segmentos de red
segmentación de los dominios de difusión
selección de los mejores trayectoria basada en hacer frente a lógicas
selección de los mejores trayectoria basada en direccionamiento físico
19
Consulte la presentación. Después de host 2 está conectado al switch de la LAN, el host 2 no puede comunicarse
con el host 1. ¿Cuál es la causa de este problema?
La máscara de subred del host 2 es incorrecta.
Host 1 y el host 2 se encuentran en redes diferentes.
El switch necesita una dirección IP que no está configurado.
La interfaz LAN del router y el host 1 se encuentran en redes diferentes.
La dirección IP del host 1 se encuentra en una red diferente a la que la interfaz LAN del router.
20
Consulte la presentación. Todos los routers tienen una ruta en su tabla de enrutamiento para cada red que se
muestra en la exposición. Rutas por defecto no se han publicado en estos routers. ¿Qué puede concluir acerca de
cómo los paquetes se reenvían en esta red? (Elija dos.)
Si RouterC recibe un paquete que está destinado a 10.5.1.1, que será remitido a la interfaz Fa0 / 0.
Si Router recibe un paquete que está destinado a 192.168.3.146, que será remitido a la interfaz S0/0/1.
Si RouterB recibe un paquete que está destinado a 10.5.27.15, será remitida a la interfaz S0/0/1.
Si RouterB recibe un paquete que está destinado a 172.20.255.1, que será remitido a la interfaz S0/0/0.
Si RouterC recibe un paquete que está destinado a 192.16.5.101, será remitida a la interfaz S0/0/1.
21
La conexión en serie se muestra en el gráfico necesita ser configurado. Comandos de configuración que se debe
hacer en el router Sydney para establecer la conectividad con el sitio de Melbourne? (Elija tres.)
Sydney (config-if) # dirección IP 201.100.53.2 255.255.255.0
Sydney (config-if) # no shutdown
Sydney (config-if) # dirección IP 255.255.255.224 201.100.53.1
Sydney (config-if) # velocidad de reloj 56000
Sydney (config-if) # ip de host Melbourne 201.100.53.2
22
¿Qué dos afirmaciones describen correctamente los componentes de un router? (Elija dos.)
RAM almacena los archivos de configuración utilizados durante la secuencia de arranque.
ROM contiene los diagnósticos ejecutados en los módulos de hardware.
NVRAM almacena una copia de seguridad del IOS usado durante la secuencia de arranque.
La memoria flash no pierde su contenido durante un reinicio.
ROM contiene la versión más actualizada y más completa de la IOS.
Flash contiene comandos de arranque del sistema para identificar la ubicación de la IOS.
23
Un administrador de red acaba de entrar en nuevas configuraciones en Router1. ¿Qué comando debería ser
ejecutado para guardar los cambios de configuración en la NVRAM?
Router1 # copy running-config Flash
Router1 (config) # copy running-config Flash
Router1 # copy running-config startup-config
Router1 (config) # copy running-config startup-config
Router1 # copia startup-config running-config
Router1 (config) # copia startup-config running-config