ESSER Fire Alarm System

Honeywell Proprietary 2 Document control number

History of Esser

1973 Establishment of Electronic Fire Alarm Systems in Hamburg 1975 Acquisition by Klaus Esser GmbH in Neuss 1985 Integration of Intruder Alarm 1993 Acquisition by Caradon plc, 2001 renamed in Novar 2005 Acquisition by Honeywell

Honeywell Proprietary 3 Document control number

Leading Technology

High Speed processor. ESSER IQ8QUAD. De-Centralized Intelligence. Built-in isolator. Powered Loop Devices 3.5Km Loop length 10,000 events log 3 level networking Dual Battery circuit in Panels 127 Devices per loop

essernet

Main Panel(MP)

Sub Panel(SP)

Sub Panel(SP)

Example switch off

Control (AE)Main detector (MFAB)Test operation

Switch-offessernet Panel

(ENP)

Operation

Honeywell Proprietary 4 Document control number

esserbus PLus

esserbus PLus (LOOP)

Monitor Control

Honeywell Proprietary 5 Document control number

Features

Short circuit Isolator integrated in every detector Automatic addresses Additional operation indicator LED Aesthetically pleasing CPU failure mode Temperature range of 20deg to 70deg C. EMI tested for 50 V/M

IQ8Quad Detector

Honeywell Proprietary 6 Document control number

Series IQ8Quad detectors Smoke Detector

Heat Detector black ring

LASER barcode label

LED green Indicating operation

Honeywell Proprietary 7 Document control number

Alarming Normal Operation

IQ8Quad Operation

Honeywell Proprietary 8 Document control number

The Small MCP

MCP (without 2nd micro switch) with isolator only Small and stylish design Approval acc. to EN 54 Part 11 Fix to existing flush-mounting box possible Additional green LED for normal operation of bus

detector Exchangeable label on housing Pictogram instead of wording Three key-functions

Reset Test Alarm Open housing

IP 43, IP55 with surface mounting box and protective cover

IQ8MCP

Honeywell Proprietary 9 Document control number

Esserbus Transponder

The Esserbus transponder works as a loop device on the multifunctional loop. It can monitor and control 3rd Party devices.

up to 31 Esserbus transponders 4 zones / 2 relays and/or 12 relay on one multifunctional primary loop

max. 100 transponders per fire alarm control panel

max. 127 detector zones per analog loop

Honeywell Proprietary 10 Document control number

Esserbus Transponder

The IQ8TAL is equipped with an integrated loop isolator, a contact input and a relay output. The relay can be optionally configured as a normally-closed contact or as a normally-open contact. The IQ8TAL does not need a separate voltage supply.

Honeywell Proprietary 11 Document control number

IQ8 Alarm Sounder

Completely bus supplied alarm device

Powered loop compatible

Up to 32 alarm devices for each powered loop

Each alarm device with built-in isolator

Acoustic pressure up to 99 dB(A) @ 1 m

Volume programmable in 8 steps via tools 8000 20 different signaling tones

Honeywell Proprietary 12 Document control number

Venturi Air Duct Detector

Easy maintenance Air stream visible OT Blue inside Inlet and drain of air in one tube

Honeywell Proprietary 16 Document control number

General view of the display and operating elements

Single zone indicator unit (GEA) Common display FIRE

Common display PRE-ALARM Common display TROUBLE

Common display disconnection Alphanumeric display Key switch Operating elements Function keys and keyboard

Opening for Programming connector

Honeywell Proprietary 17 Document control number

Configuration example IQ8Control M

Con

nect

or 1

Con

nect

or 2

Basic module IQ8Control

Extension module with 3 micro module slots

esse

rnet

m

odul

e

Analog loop module 1

Extension module with 3 micro module slots

Analog loop module 2

Analog loop module 3

Analog loop module 4

Analog loop module 5

Analog loop module 6

Honeywell Proprietary 18 Document control number

Operation

The common display >Fire< is activated if at least one fire alarm has been detected. The originating detector or detector zone will be shown on the alphanumeric display

Fire Condition

Acknowledgement of the control panel buzzer. This key remains active when the keyboard is locked. The buzzer is reactivated in the case of a further event.

All detected fire alarms, detector zones, displays and technical alarm signals are cancelled and returned to normal condition.

Honeywell Proprietary 19 Document control number

Operation..cont. Trouble Condition

The common display Trouble is activated if at least one malfunction has been detected. The reason will be shown on the alphanumeric display.

A component of the fire alarm control panel or a monitored relay output such as an external

alarm device has malfunctioned.

The power supply (battery or mains voltage) is connected. The fire alarm control panel is in an

operative condition.

The fire alarm control panel is only partially operative due to a malfunction of the control panel

functions. Display or operation of the control panel is no longer

possible

The power supply (battery or mains voltage) is out of order.

Honeywell Proprietary 20 Document control number

Operation..cont.

Disconnect a detector

Switch ON/ reset a detector

Honeywell Proprietary 21 Document control number

Transponder

Honeywell Proprietary 22 Document control number

Trouble codes

Honeywell Proprietary 23 Document control number

Trouble codes..Cont

Honeywell Proprietary 24 Document control number

Trouble codes..Cont

Honeywell Proprietary 25 Document control number

Esser by Honeywell

Thank you for your Time & Attention

Slide Number 1Slide Number 2Leading Technologyesserbus PLusSlide Number 5Series IQ8Quad detectorsSlide Number 7Slide Number 8Slide Number 9Slide Number 10Slide Number 11Venturi Air Duct DetectorGeneral view of the display and operating elements Configuration example IQ8Control MOperationOperation..cont.Operation..cont.TransponderTrouble codesTrouble codes..ContTrouble codes..ContEsser by Honeywell