Experimentally Validated Computational Modeling of Creep ...
Equipment for Engineering Education & Research THERMAL ...solution.com.my/pdf/HE157(A4).pdf ·...
Transcript of Equipment for Engineering Education & Research THERMAL ...solution.com.my/pdf/HE157(A4).pdf ·...
THERMAL CONDUCTIVITYOF
INSULATING POWDERS
SOLTEQ®
MODEL: HE 157
This Thermal Conductivity of Insulating Powders Unit (Model: HE 157) has been specially designed to
allow students to experimentally determine the thermal conductivity of insulating powders such as
magnesium oxide, mica and kaolin. This complete benchtop unit comes with three stainless steel testmodules containing insulating powders to be determined their thermal conductivities.
DESCRIPTION
Each test module is supplied with a 200 W variable input
cartridge heater. Each test module is fitted with six
temperature sensors for measurements of T1 and T2.
A proper insulating material is fitted inside the test
modules to ensure heat transfer is in the radial direction
only. The unit has a control panel with digital indicators
for temperatures and heater power, a thermocouple
selector switch, and a heater power controller.
EXPERIMENTAL CAPABILITIES
The unit allows students to do the following experiments:
a) To determine the thermal conductivity of insulating
powders.
b) To compare the experimental results with known
values if available.
Equipment for Engineering Education & Research
Rev1.0 15/06/2011
SOLTEQ
SOLTEQ®
SPECIFICATIONS
The complete unit includes the followings:
a) Bench:
Made of high quality and sturdy formica laminated
panel on which main components are mounted.
b) Test Modules:
Three sets of test modules are supplied made of
two concentric stainless steel cylinders with the
following dimensions:
Outer Cylinder:
I.D. : 102.3 mm
Thickness : 6.02 mm
Length : approx. 185 mm
Inner Cylinder
I.D. : 9.9 mm
Thickness : 3.0 mm
Length : approx. 175 mm
Each test module is fitted with top cover made of
stainless steel and Teflon seals at the top and
bottom section.
Each test module is pre-filled with test powder to
be determines its thermal conductivity.
c) Heater:
Type : high temperature cartridge heater
Power : 200 W, with built-in temperature
sensor
Control : 0 to 200 W by means of a variable
transformer.
Safety : High temperature cut-out by
means of a temperature controller.
d) Instrumentations:
The unit is supplied with 6 temperature sensors
for each test modules. A selector switch is provided
to allow students to read temperatures at various
points.
e) Control Panel:
The control panel includes all necessary electrical
wiring with variable transformer, power transducer,
temperature controller/indicator, digital indicators for
temperatures and heater power, and thermocouple
selector switch.
REQUIREMENTS
Electrical : 220 to 240 VAC/1-phase/50 Hz
OVERALL DIMENSIONS
Height : 0.95 m
Width : 1.27 m
Depth : 0.66 m
MANUAL
The unit is supplied with Operating and Experimental
Manuals in English.
TRAINING
Training will be conducted to handing over of the unit.
Equipment for Engineering Education & Research
Rev1.0 15/06/2011
Our range of teaching equipment can be complemented with our
SOLDAS and SOLCAL software.
SOFTWARE & E - LEARNING
SOLDAS - Supervisory Control & Data Acquisition
- Data Logging
- Signal Analysis
- Process Control
- Real-Time Display
- Tabulated Results
- Graph of Experimental Results
SOLCAL - Computer Aided Learning
- Multimedia Features
- Interactive
- Graphic Simulation
- Experiment Result Samples
- Full Experiment Manuals
SOLTEQ®
Contact us for a catalog CD
SOLUTION ENGINEERING SDN. BHD.(Co. No. 174876-M)
Sales Office :
No.3, Jalan TPK 2/4, Taman Perindustrian Kinrara,47100 Puchong, Selangor Darul Ehsan, Malaysia.Tel. No. : +(603) 80758000
Fax. No.: +(603) 80755784
R&D Office :
G-2A, Incubator 3, Technology Park Malaysia,Bukit Jalil, 57000 Kuala Lumpur, Malaysia.Tel. No. : +(603) 8996 0023
Email : [email protected] site : http//www.solution.com.my/
AGENT:
Equipment for Engineering Education & Research
BUATAN MALAYSIA
MSC- StatusCompany
®
®
Rev1.0 15/06/2011