Exploring networks-on-chip for FPGAs - The Computer Laboratory
Environmental control for a chip scale laboratory
description
Transcript of Environmental control for a chip scale laboratory
ENVIRONMENTAL CONTROL FOR A CHIP SCALE
LABORATORY
Team:Robert Bouda - LeaderAshok Rajan – Communication Liaison Sean Belieu – WebmasterSahan FernandoTianyu WangZhaokui Wang
Faculty Advisor & Client: Dr. Liang Dong
System DescriptionProblem Need Statement:A greenhouse is costly, space intensive, and we are looking to solve it.
Functional Requirements
• Solenoid Control System1. A system using Verilog or VHDL capable of
receiving and decoding a serial digital signal• Sensor Array
1. A control element that sends data in a serial digital format to a different system designed to regulate
• Channel and Chamber fabrication1. A flow channels capable of delivering liquid to
individual chambers at volumes of 1µm3.
2. 7 air flow channels designed to depress and restrict flow through liquid channels using air pressure.
Risks
• Channel thickness
Solenoid Valves
Solenoid ValvesThe connections with the chip are done using thin tubing and syringes:
Solenoid Valves
Clippard(12-ET-2M-6)• Extremely basic solenoids• 25-pin interface• Multisim – Verilog
Existing technology:• FluidigmGenetic Analysis
Work plan – Subgroup 1• This semester:
Design the control logic of solenoid valves to: a) Control the liquid flow into the growth chambers b) Select a specific growth chamber out of 128 growth chambers
that are fabricated on an interface.
• Next semester:• Intergrate sensor unit and fabricated channels with Solenoid
control
Sensor Unit
The sensor detects temperature/ humidity and outputs the data via serial DATA to a micro-controller.
This data will be outputted via the micro-controller in binary form to the solenoid control system.
Work plan – Subgroup 2This semester:
• A sensor unit that will successfully read environmental Temperature/Humidity and output data to the control system
Current:• Actual circuit design• Coding the Micro-controller
Next Semester:• Intergrate sensor unit with Solenoid control
• There are 128 micro-greenhouses totally .• And there are 128 channel connect to each of them.• 7 bits are used to make them work individually.(2^7=128)• (As shown above)
Microfluidics Channels
Fabrication process
Firstly, we fabricate our molds on glass slide by using IBA. Then Once the slides are ready, we used as molds for PDMS, when the control and flow layers is prepared separately we bond them together crossing to each other.
Two layers device• The designed chip has
two layers:• flow level(Top), where the
cells will ultimately grow.• control layer(Under),
used to close and open certain valves by putting under pressure the thin membrane between the control and the flow layers.
Work plan – Subgroup 3This semester:
• Learning how to fabricate.• Learn fabrication with the IBA(isobornyl acrylate) process• Learn PDMS(Polydimethylsiloxane) fabrication process• Make a two layers devices and perform tests on it to ensure
quality of devices.
Next Semester:• Ensure interface that was created serves as a good mediator
between the other two sub projects.
Projected CostsMaterial Product (Not Final) Cost ( Estimation)
Solenoid Valves (Qty-12) Clippard12 ET – 2M – 6
$340.00
Electronic Manifold (Qty-1) ClippardEMC – 12 – 06 – 20
$260.00
Temeprature & Humidity sensor (Qty-1)
SensironSHT11
$40.00
Tubing Adaptors (Qty-12) - $30.00
Tubing Cole PalmerEW-06418-02
Donated by Client
IBA Fabrication Glass - Donated by Client
MCU for Sensor and Solenoids - Currently Available Lab Equipment
Total $670
Final DeliverablesThe expected end product will consist of three sub-systems that
will be combined to form the complete chip-scale greenhouse system
End Product• Temperature and Humidity Sensing Unit • Solenoid Control System• Liquid flow channels
Questions?