ELECTRICAL AV A - JustAnswer › DoritoWhatz › ff5c7cd7-0... · • Do not use electrical test...

AV-1

ELECTRICAL

C

D

E

F

G

H

I

J

L

M

SECTION AV A

B

AV

N

O

P

CONTENTS

AUDIO, VISUAL, NAVIGATION & TELEPHONE SYS-TEM

AUDIO WITHOUT NAVIGATION

SERVICE INFORMATION ............................ 4

PRECAUTIONS ................................................... 4Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TEN-SIONER" ...................................................................4Precaution Necessary for Steering Wheel Rota-tion After Battery Disconnect .....................................4

PREPARATION ................................................... 6Commercial Service Tool ..........................................6

AUDIO ................................................................. 7Component Parts Location ........................................7System Description ...................................................8Schematic ...............................................................11Wiring Diagram - AUDIO - .......................................14Audio Unit (Base System) Harness Connector Terminal Layout ......................................................38Terminal and Reference Value for Audio Unit (Base System) .........................................................38Audio Unit (Mid System) Harness Connector Ter-minal Layout ............................................................39Terminal and Reference Value for Audio Unit (Mid System) ...................................................................39AV Control Unit (Premium System without Rock-ford Fosgate) Harness Connector Terminal Lay-out ...........................................................................42Terminal and Reference Value for AV Control Unit (Premium System without Rockford Fosgate) .........42AV Control Unit (Premium System with Rockford Fosgate) Harness Connector Terminal Layout .......45Terminal and Reference Value for AV Control Unit (Premium System with Rockford Fosgate) ..............46Audio Amplifier Harness Connector Terminal Lay-out ...........................................................................49Terminal and Reference Value for Audio Amplifier ....50

IPod Adapter Harness Connector Terminal Layout ....52

Terminal and Reference Value for IPod Adapter .....52Satellite Radio Tuner Harness Connector Termi-nal Layout ................................................................54Terminal and Reference Value for Satellite Radio Tuner .......................................................................55Trouble Diagnosis ....................................................55Noise Inspection ......................................................58Audio Unit (Base and Mid System) Power and Ground Supply Circuit Inspection ............................58AV Control Unit (Premium System) Power and Ground Supply Circuit Inspection ............................59Audio Amplifier Power and Ground Supply Circuit Inspection ................................................................60Satellite Radio Tuner Power and Ground Supply Circuit Inspection .....................................................61Satellite Radio Tuner Communication Circuit In-spection (Mid System) .............................................61Satellite Radio Tuner Communication Circuit In-spection (Premium System) ....................................63Satellite Radio Tuner Left Channel Audio Signal Circuit Inspection (Mid System) ...............................64Satellite Radio Tuner Left Channel Audio Signal Circuit Inspection (Premium System) ......................65Satellite Radio Tuner Right Channel Audio Signal Circuit Inspection (Mid System) ...............................66Satellite Radio Tuner Right Channel Audio Signal Circuit Inspection (Premium System) ......................67Steering Switch Check (With Bluetooth) ..................67Steering Switch Check (Without Bluetooth) .............69Sound Is Not Heard from Front Door Speaker or Front Tweeter (Base and Mid System) ....................70Sound Is Not Heard from Front Door Speaker or Front Tweeter (Premium System without Rockford Fosgate) ..................................................................72Sound Is Not Heard from Rear Speaker (Base and Mid System) .............................................................74Sound Is Not Heard from Rear Speaker (Premium System without Rockford Fosgate) ..........................76

Revision: October 2011 2010 Sentra

AV-2

Sound Is Not Heard from Front Door Speaker or Front Tweeter (Premium System with Rockford Fosgate) ................................................................. 77Sound Is Not Heard from Rear Speaker Assembly (Premium System with Rockford Fosgate) ............. 80Removal and Installation ........................................ 83

USB CONNECTOR AND AUX JACK ............... 88Removal and Installation ........................................ 88

AUDIO ANTENNA ............................................. 89Location of Antenna ................................................ 89Removal and Installation of Roof Antenna ............. 89

TELEPHONE ..................................................... 91Component Parts and Harness Connector Loca-tion .......................................................................... 91System Description ................................................. 91Wiring Diagram - H/PHON - .................................... 95Bluetooth Control Unit Harness Connector Termi-nal Layout ............................................................... 99Terminal and Reference Value for Bluetooth Con-trol Unit ................................................................... 99Bluetooth Control Unit Self-Diagnosis Function ....101How to Proceed with Trouble Diagnosis ................102Malfunction Code/Symptom Chart .........................102Power Supply and Ground Circuit Inspection for Bluetooth Control Unit ...........................................102Steering Wheel Audio Control Switch Does Not Operate ..................................................................103Voice Activated Control Function Does Not Oper-ate ..........................................................................104Removal and Installation .......................................107

REAR VIEW CAMERA .................................... 110Component Parts and Harness Connector Loca-tion .........................................................................110System Description ................................................111Wiring Diagram - R/VIEW - ....................................112Rear View Camera Power Supply and Ground Cir-cuit Inspection ........................................................112Removal and Installation .......................................114

iPod® CONNECTOR ....................................... 115Removal and Installation .......................................115

iPod® ADAPTER ............................................. 116Removal and Installation .......................................116

AUDIO WITH NAVIGATION

SERVICE INFORMATION ..........................117

PRECAUTIONS ............................................... 117Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TEN-SIONER" ................................................................117Precaution Necessary for Steering Wheel Rota-tion After Battery Disconnect .................................117

PREPARATION ............................................... 119Commercial Service Tool ......................................119

AUDIO ...............................................................120Component Parts Location ................................... 120System Description ............................................... 121Schematic ............................................................. 123Wiring Diagram - AUDIO - .................................... 125AV Control Unit (Without Rockford Fosgate) Har-ness Connector Terminal Layout .......................... 138Terminal and Reference Value for AV Control Unit (Without Rockford Fosgate) .................................. 138AV Control Unit (With Rockford Fosgate) Harness Connector Terminal Layout ................................... 141Terminal and Reference Value for AV Control Unit (With Rockford Fosgate) ....................................... 141Audio Amplifier Harness Connector Terminal Lay-out (With Rockford Fosgate) ................................. 144Terminal and Reference Value for Audio Amplifier (With Rockford Fosgate) ....................................... 144On-Board Diagnosis .............................................. 146Symptom Chart ..................................................... 149AV Control Unit Power and Ground Supply Circuit Inspection .............................................................. 151Audio Amplifier Power and Ground Supply Circuit Inspection .............................................................. 152Steering Switch Check .......................................... 153Sound Is Not Heard from Front Door Speaker or Front Tweeter (Without Rockford Fosgate) ........... 154Sound Is Not Heard from Rear Speaker (Without Rockford Fosgate) ................................................ 155Sound Is Not Heard from Front Door Speaker or Front Tweeter (With Rockford Fosgate) ................ 156Sound Is Not Heard from Rear Speaker Assembly (With Rockford Fosgate) ....................................... 159Removal and Installation ....................................... 162

NAVIGATION SYSTEM ....................................166How to Proceed with Trouble Diagnosis ............... 166

TELEPHONE ....................................................167Component Parts and Harness Connector Loca-tion ........................................................................ 167System Description ............................................... 167Wiring Diagram - H/PHON - .................................. 170Bluetooth Control Unit Harness Connector Termi-nal Layout ............................................................. 172Terminal and Reference Value for Bluetooth Con-trol Unit .................................................................. 172Bluetooth Control Unit Self-Diagnosis Function .... 173How to Proceed with Trouble Diagnosis ............... 174Malfunction Code/Symptom Chart ........................ 174Power Supply and Ground Circuit Inspection for Bluetooth Control Unit ........................................... 174Steering Wheel Audio Control Switch Does Not Operate ................................................................. 175Voice Activated Control Function Does Not Oper-ate ......................................................................... 175Removal and Installation ....................................... 177

REAR VIEW CAMERA .....................................180


AV-3

C

D

E

F

G

H

I

J

L

M

A

B

AV

N

O

P

Component Parts and Harness Connector Loca-tion ........................................................................ 180System Description ............................................... 180Wiring Diagram - R/VIEW - ................................... 182Rear View Camera Power Supply and Ground Cir-cuit Inspection ....................................................... 182Camera Image Signal Circuit ................................ 184Removal and Installation ....................................... 185

USB CONNECTOR AND AUX JACK ............. 186Removal and Installation .......................................186

AUDIO ANTENNA ........................................... 187Location of Antenna ...............................................187Removal and Installation of Roof Antenna ............187

GPS ANTENNA ............................................... 189Location of Antenna ...............................................189Removal and Installation .......................................189


AV-4

< SERVICE INFORMATION > [AUDIO WITHOUT NAVIGATION]PRECAUTIONS

SERVICE INFORMATIONPRECAUTIONSPrecaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" INFOID:0000000005485388

The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used alongwith a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certaintypes of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRSsystem uses the seat belt switches to determine the front air bag deployment, and may only deploy one frontair bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.Information necessary to service the system safely is included in the SRS and SB section of this Service Man-ual.WARNING:• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in

the event of a collision which would result in air bag inflation, all maintenance must be performed byan authorized NISSAN/INFINITI dealer.

• Improper maintenance, including incorrect removal and installation of the SRS can lead to personalinjury caused by unintentional activation of the system. For removal of Spiral Cable and Air BagModule, see the SRS section.

• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in thisService Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-ness connectors.

PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERSWARNING:• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-

tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with ahammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causingserious injury.

• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect thebattery, and wait at least 3 minutes before performing any service.

Precaution Necessary for Steering Wheel Rotation After Battery DisconnectINFOID:0000000005485387

NOTE:• This Procedure is applied only to models with Intelligent Key system and NATS (NISSAN ANTI-THEFT SYS-

TEM).• Remove and install all control units after disconnecting both battery cables with the ignition knob in the″LOCK″ position.

• Always use CONSULT-III to perform self-diagnosis as a part of each function inspection after finishing work.If DTC is detected, perform trouble diagnosis according to self-diagnostic results.

For models equipped with the Intelligent Key system and NATS, an electrically controlled steering lock mech-anism is adopted on the key cylinder.For this reason, if the battery is disconnected or if the battery is discharged, the steering wheel will lock andsteering wheel rotation will become impossible.If steering wheel rotation is required when battery power is interrupted, follow the procedure below beforestarting the repair operation.

OPERATION PROCEDURE1. Connect both battery cables.

NOTE:Supply power using jumper cables if battery is discharged.

2. Use the Intelligent Key or mechanical key to turn the ignition switch to the ″ACC″ position. At this time, thesteering lock will be released.

3. Disconnect both battery cables. The steering lock will remain released and the steering wheel can berotated.

4. Perform the necessary repair operation.


PRECAUTIONS

AV-5

< SERVICE INFORMATION > [AUDIO WITHOUT NAVIGATION]

C

D

E

F

G

H

I

J

L

M

A

B

AV

N

O

P

5. When the repair work is completed, return the ignition switch to the ″LOCK″ position before connectingthe battery cables. (At this time, the steering lock mechanism will engage.)

6. Perform a self-diagnosis check of all control units using CONSULT-III.


AV-6

< SERVICE INFORMATION > [AUDIO WITHOUT NAVIGATION]PREPARATION

PREPARATIONCommercial Service Tool INFOID:0000000005283567

Tool name Description

Power tool Loosening bolts and nuts

PBIC0191E


AUDIO

AV-7


C

D

E

F

G

H

I

J

L

M

A

B

AV

N

O

P

AUDIOComponent Parts Location INFOID:0000000005283568

AWNIA1993ZZ


AV-8

< SERVICE INFORMATION > [AUDIO WITHOUT NAVIGATION]AUDIO

iPod® is a trademark of Apple inc., registered in the U.S. and other countries.

System Description INFOID:0000000005283569

BASE AND MID SYSTEMRefer to Owner's Manual for audio system operating instructions.Power is supplied at all times• through 20A fuse (No. 31, located in the fuse and fusible link box)• to audio unit terminal 19.With the ignition switch in the ACC or ON position, power is supplied• through 10A fuse [No. 6, located in the fuse block (J/B)]• to audio unit terminal 7.Ground is supplied to• audio unit terminal 28 (with mid system) and 20• through grounds M57 and M61.Then audio signals are supplied

1. Front tweeter LH M46 (mid and pre-mium system)

2. Audio unit M43, M45, M53, M90(base and mid system)

3. Front tweeter RH M47 (mid and pre-mium system)

4. AV control unit M92, M93, M94, M96, M97 (premium system)

5. Steering wheel audio control switch-es (if equipped)

6. Front door speakerLH D10RH D108

7. Rear speaker LH B27 (base, mid and premium without Rockford Fosgatesystem)Rear speaker assembly LH B40(premium system with Rockford Fos-gate)

8. Rear speaker RH B39 (base, midand premium without Rockford Fos-gate system)Rear speaker assembly RH B38(premium system with Rockford Fos-gate

9. Satellite radio tuner B56, B60 (withsatellite radio tuner)

10. Bluetooth control unit B15 (withBluetooth)

11. Audio amplifier B43, B44 (premiumsystem with Rockford Fosgate)

12. iPod® adapter M91 (mid system,view with console side finisher - RHremoved)

13. iPod® connector M226 (mid system)USB interface M228 (premium sys-tem)

14. Rear view camera T21(with rearview camera)

AWNIA1994ZZ


AUDIO

AV-9


C

D

E

F

G

H

I

J

L

M

A

B

AV

N

O

P

• through audio unit terminals 2, 3, 4, 5, 11, 12, 13 and 14• to terminals + and - of front door speaker LH and RH• to terminals + and - of front tweeter LH and RH (with mid system) and• to terminals + and - of rear speaker LH and RH.

PREMIUM SYSTEM (WITHOUT ROCKFORD FOSGATE)Refer to Owner's Manual for audio system operating instructions.Power is supplied at all times• through 20A fuse (No. 31, located in the fuse and fusible link box)• to AV control unit terminal 19.With the ignition switch in the ACC or ON position, power is supplied• through 10A fuse [No. 6, located in the fuse block (J/B)]• to AV control unit terminal 7.Ground is supplied to• to AV control unit terminals 20, 27 and 47• through grounds M57 and M61.Then audio signals are supplied• through AV control unit terminals 2, 3, 4, 5, 11, 12, 13 and 14• to terminals + and - of front door speaker LH and RH• to terminals + and - of front tweeter LH and RH and• to terminals + and - of rear speaker LH and RH.

PREMIUM SYSTEM (WITH ROCKFORD FOSGATE)Refer to Owner's Manual for audio system operating instructions.Power is supplied at all times• through 20A fuse [No. 17, located in the fuse block (J/B)]• to audio amplifier terminal 17,• through 20A fuse (No. 31, located in the fuse and fusible link box)• to audio amplifier terminal 1 and• to AV control unit terminal 19.With the ignition switch in the ACC or ON position, power is supplied• through 10A fuse [No. 6, located in the fuse block (J/B)]• to AV control unit terminal 7.Ground is supplied to• to AV control unit terminals 20, 27 and 47• through grounds M57 and M61.Ground is also supplied• to audio amplifier terminals 4 and 20• through grounds B7 and B19.Then audio signals are supplied• through AV control unit terminals 53, 54, 57, 58, 59, 60, 63, and 64• to audio amplifier terminals 5, 6, 7, 8, 21, 22, 23 and 24.Audio signals are amplified by the audio amplifier.The amplified audio signals are supplied• through audio amplifier terminals 2, 3, 11, 12, 13, 14, 15, 16, 18, 19, 27, 28, 29, 30, 31 and 32• to terminals + and - of front door speaker LH and RH and• to terminals + and - of front tweeter LH and RH• to terminals 1, 2, 3 and 4 of rear speaker assembly LH and RH.

STEERING WHEEL AUDIO CONTROL SWITCHES (IF EQUIPPED)When one of steering wheel audio control switches is pushed, the resistance in steering switch circuit changesdepending on which button is pushed.

SATELLITE RADIO TUNER (IF EQUIPPED)Power is supplied at all times• through 20A fuse (No. 31, located in the fuse and fusible link box)• to satellite radio tuner terminal 32.With the ignition switch in the ACC or ON position, power is supplied• through 10A fuse [No. 6, located in the fuse block (J/B)]• to satellite radio tuner terminal 36.Ground is supplied through the case of the satellite radio tuner.Then audio signals are supplied


AV-10


• through satellite radio tuner terminals 21, 22, 23 and 24• to audio unit terminals 45, 46, 47 and 48 (with mid system) or• to AV control unit terminals 65, 66, 67 and 68 (with premium system).

SPEED SENSITIVE VOLUME SYSTEM (MID AND PREMIUM SYSTEM)Volume level of this system goes up and down automatically in proportion to the vehicle speed. The controllevel can be selected by the customer. Refer to Owner's Manual for operating instructions.


AUDIO

AV-11


C

D

E

F

G

H

I

J

L

M

A

B

AV

N

O

P

Schematic INFOID:0000000005283570

MID SYSTEM

AANWA0181GB


AV-12


PREMIUM SYSTEM (WITHOUT ROCKFORD FOSGATE)

AANWA0182GB


AUDIO

AV-13


C

D

E

F

G

H

I

J

L

M

A

B

AV

N

O

P

PREMIUM SYSTEM (WITH ROCKFORD FOSGATE)

AANWA0183GB


AV-14


Wiring Diagram - AUDIO - INFOID:0000000005283571

BASE SYSTEM

AANWA0184GB


AUDIO

AV-15


C

D

E

F

G

H

I

J

L

M

A

B

AV

N

O

P

MID SYSTEM

AANWA0185GB


AV-16


AANWA0186GB


AUDIO

AV-17


C

D

E

F

G

H

I

J

L

M

A

B

AV

N

O

P

Without Bluetooth

AANWA0187GB


AV-18


With Bluetooth

AANWA0188GB


AUDIO

AV-19


C

D

E

F

G

H

I

J

L

M

A

B

AV

N

O

P

AANWA0189GB


AV-20


AANWA0190GB


AUDIO

AV-21


C

D

E

F

G

H

I

J

L

M

A

B

AV

N

O

P

AANWA0191GB


AV-22


PREMIUM SYSTEM - WITHOUT ROCKFORD FOSGATE

AANWA0192GB


AUDIO

AV-23


C

D

E

F

G

H

I

J

L

M

A

B

AV

N

O

P

AANWA0193GB


AV-24


AANWA0195GB


AUDIO

AV-25


C

D

E

F

G

H

I

J

L

M

A

B

AV

N

O

P

AANWA0196GB


AV-26


AANWA0197GB


AUDIO

AV-27


C

D

E

F

G

H

I

J

L

M

A

B

AV

N

O

P

AANWA0198GB


AV-28


PREMIUM SYSTEM - WITH ROCKFORD FOSGATE

AANWA0199GB


AUDIO

AV-29


C

D

E

F

G

H

I

J

L

M

A

B

AV

N

O

P

AANWA0200GB


AV-30


AANWA0201GB


AUDIO

AV-31


C

D

E

F

G

H

I

J

L

M

A

B

AV

N

O

P

AANWA0202GB


AV-32


AANWA0203GB


AUDIO

AV-33


C

D

E

F

G

H

I

J

L

M

A

B

AV

N

O

P

AANWA0204GB


AV-34


AANWA0205GB


AUDIO

AV-35


C

D

E

F

G

H

I

J

L

M

A

B

AV

N

O

P

AANWA0206GB


AV-36


AV COMMUNICATION - WITH MID SYSTEM

AANWA0219GB


AUDIO

AV-37


C

D

E

F

G

H

I

J

L

M

A

B

AV

N

O

P

AV COMMUNICATION - WITH PREMIUM SYSTEM

AANWA0220GB


AV-38


Audio Unit (Base System) Harness Connector Terminal Layout INFOID:0000000005283572

Terminal and Reference Value for Audio Unit (Base System) INFOID:0000000005283573

WKIA5439E

Terminal(Wire color)

ItemSignal input/output

ConditionReference value

(Approx.)+ – Ignition

switch Operation

2 (L) 3 (W) Audio signal front LH Output ON Receive audio signal

4 (G) 5 (V) Audio signal rear LH Output ON Receive audio signal

7 (GR) Ground ACC power supply Input ACC — Battery voltage

11 (P) 12 (R) Audio signal front RH Output ON Receive audio signal

13 (L) 14 (Y) Audio signal rear RH Output ON Receive audio signal

19 (Y) Ground Battery power supply Input OFF — Battery voltage

20 (B) Ground Ground — ON — —

SKIB3609E

SKIB3609E

SKIB3609E

SKIB3609E


AUDIO

AV-39


C

D

E

F

G

H

I

J

L

M

A

B

AV

N

O

P

Audio Unit (Mid System) Harness Connector Terminal Layout INFOID:0000000005283574

Terminal and Reference Value for Audio Unit (Mid System) INFOID:0000000005283575

AWNIA1989GB

Terminal (Wire color)



(Approx.)Example of symp-

tom+ – Ignition

switch Operation

2 (L) 3 (W)Audio sound signal front LH

Output ON Receive audio signal

No sound from front door speaker LH or tweeter LH.

4 (G) 5 (V)Audio sound signal rear LH


No sound from rear speaker LH.

6 (P) Ground Remote control A Input ON

Press Phone/End switch 0V

Steering wheel au-dio controls do not function

Press SEEK UP switch 1.7V

Press VOL UP switch 3.3V

Except for above 5.0V

7 (GR) Ground ACC signal Input ON Ignition switch ACC or ON Battery voltage System does not

work properly.

11 (P) 12 (R)Audio sound signal front RH


No sound from front door speaker RH or tweeter RH.

SKIA0177E

SKIA0177E

SKIA0177E


AV-40


13 (L) 14 (Y)Audio sound signal rear RH


No sound from rear speaker RH.

15 (LG) —Remote control ground

Input — — —Steering wheel au-dio controls do not function

16 (L) Ground Remote control B Input ON

Press Phone/Send switch 0V


Press SEEK DOWN switch 1.7V

Press VOL DOWN switch 3.3V


18 (O) GroundVehicle speed signal (8-pulse)

Input ON

When vehicle speed is approx. 40 km/h (25 MPH)

Ground

19 (Y) Ground Battery pow-er Input — — Battery voltage System does not

work properly.

20 (B) Ground Ground — — — — —

25 (L) —AV commu-nication sig-nal 1 (H)

Input/Output — — — —



27 (P) —AV commu-nication sig-nal 1 (L)


28 (B) Ground Ground — — — — —

32 (R) Ground TEL ON sig-nal Output ON — — —







tom+ – Ignition

switch Operation

SKIA0177E

SKIA6649J


AUDIO

AV-41


C

D

E

F

G

H

I

J

L

M

A

B

AV

N

O

P

34 (BR) 35 (Y) TEL voice audio signal Input ON

Start confirma-tion/adjustment mode, and then Voice Micro-phone Test by selecting “Voice Microphone Test” on Hands-free Microphone screen.

—

36 (GR) — Shield — — — — —

37 (G) 41 (W)iPod® au-dio signal LH

Input ON With iPod® op-erating —

39 (L) 43 (R)iPod® au-dio signal RH

Input ON With iPod® op-erating —

44 (GR) — Shield — — — — —

46 (R) 45 (G)

Audio left channel sound signal from satel-lite radio tuner

Input ON Receive audio signal

No sound from sat-ellite radio tuner left channel.

48 (B) 47 (W)

Audio right channel sound signal from satel-lite radio tuner


No sound from sat-ellite radio tuner right channel.

49 (GR) —Shield ground (au-dio signal)

— — — 0V —

50 (GR) —Shield ground (da-ta)

— — — 0V —

52 (L) Ground

Satellite ra-dio tuner re-quest to audio unit

Input ON Turn audio unit ON 5V

Satellite radio tun-er does not oper-ate properly.





tom+ – Ignition

switch Operation

SKIB3609E

SKIB3609E

SKIB3609E

SKIA0177E

SKIA0177E


AV-42


AV Control Unit (Premium System without Rockford Fosgate) Harness Connector Ter-minal Layout INFOID:0000000005548864

Terminal and Reference Value for AV Control Unit (Premium System without Rockford Fosgate) INFOID:0000000005548863

53 (LG) Ground Audio RX Input ON Receive data

Satellite radio tun-er audio informa-tion does not display properly.

54 (V) Ground Audio TX Output ON Transmit data






tom+ – Ignition

switch Operation

SKIA4403E

SKIA4402E

AWNIA1996ZZ





tom+ – Ignition

switch Operation

2 (L) 3 (W)Audio sound signal front LH



4 (G) 5 (V)Audio sound signal rear LH


No sound from rear speaker LH.

SKIA0177E

SKIA0177E


AUDIO

AV-43


C

D

E

F

G

H

I

J

L

M

A

B

AV

N

O

P








work properly.

11 (P) 12 (R)Audio sound signal front RH



13 (L) 14 (Y)Audio sound signal rear RH


No sound from rear speaker RH.










Input ON


Ground


work properly.

20 (B) Ground Ground — ON — — —





tom+ – Ignition

switch Operation

SKIA0177E

SKIA0177E

SKIA6649J


AV-44




TEL voice audio signal

26 (GR) — Shield — — — — —





30 (GR) — Shield — — — — —





33 (B) Ground

Rear view camera ground sig-nal

— — — — Ground

34 (R) GroundRear view camera ON signal

Output ON Shift selector is in R position 6V Ground

35 (L) GroundRear view camera vid-eo in (+)

Input ON With rear view camera ON Ground

36 (P) GroundRear view camera vid-eo in (-)




50 (G) Ground Reverse sig-nal Input ON R position Battery voltage Ground

Other than R position 0V





tom+ – Ignition

switch Operation

SKIB3609E

SKIB2251J

SKIB2251J


AUDIO

AV-45


C

D

E

F

G

H

I

J

L

M

A

B

AV

N

O

P

AV Control Unit (Premium System with Rockford Fosgate) Harness Connector Termi-

66 (R) 65 (G)




68 (B) 67 (W)





— — — 0V —


— — — 0V —

72 (L) Ground








77 (B) — USB ground — — — — —

78 (W) — USB D- — — — — —

79 (R) — USB V BUS signal — — — — —

80 (G) — USB D+ — — — — —

81 (GR) — SHIELD — — — — —





tom+ – Ignition

switch Operation

SKIA0177E

SKIA0177E

SKIA4403E

SKIA4402E


AV-46


nal Layout INFOID:0000000005283576

Terminal and Reference Value for AV Control Unit (Premium System with Rockford Fosgate) INFOID:0000000005283577

AWNIA1995ZZ





tom+ – Ignition

switch Operation

1 (G) Ground Amp. ON/OFF signal Output ON — More than 6.5V

Audio amplifier does not work properly.








work properly.










Input ON


Ground


work properly.


SKIA6649J


AUDIO

AV-47


C

D

E

F

G

H

I

J

L

M

A

B

AV

N

O

P



TEL voice audio signal

26 (GR) — Shield — — — — —





30 (GR) — Shield — — — — —





33 (B) Ground

Rear view camera ground sig-nal

— — — — Ground

34 (R) GroundRear view camera ON signal

Output ON Shift selector is in R position 6V Ground

35 (L) GroundRear view camera vid-eo in (+)


36 (P) GroundRear view camera vid-eo in (-)




50 (G) Ground Reverse sig-nal Input ON R position Battery voltage Ground

Other than R position 0V





tom+ – Ignition

switch Operation

SKIB3609E

SKIB2251J

SKIB2251J


AV-48


59 (W) 53 (B)Audio sound signal front LH



60 (LG) 54 (V)Audio sound signal rear LH


No sound from rear speaker as-sembly LH.

61 (GR) — Shield ground — — — — —

63 (R) 57 (L)Audio sound signal front RH



64 (BR) 58 (Y)Audio sound signal rear RH


No sound from rear speaker as-sembly RH.

66 (R) 65 (G)




68 (B) 67 (W)





— — — 0V —





tom+ – Ignition

switch Operation

SKIA0177E

SKIA0177E

SKIA0177E

SKIA0177E

SKIA0177E

SKIA0177E


AUDIO

AV-49


C

D

E

F

G

H

I

J

L

M

A

B

AV

N

O

P

Audio Amplifier Harness Connector Terminal Layout INFOID:0000000005283578


— — — 0V —

72 (L) Ground








77 (B) — USB ground — — — — —

78 (W) — USB D- — — — — —

79 (R) — USB V BUS signal — — — — —

80 (G) — USB D+ — — — — —

81 (GR) — SHIELD — — — — —





tom+ – Ignition

switch Operation

SKIA4403E

SKIA4402E

WKIA5763E


AV-50


Terminal and Reference Value for Audio Amplifier INFOID:0000000005283579

Terminal(wire color)



(Approx.)Example ofsymptom

+ – Ignition switch Operation

1 (R) Ground Battery Input — — Battery voltage System does not work properly.

2 (W) 18 (B) Subwoofer LH Output ON Receive audio signal

No sound from subwoofer LH.

3 (Y) 19 (L) Subwoofer RH Output ON Receive audio signal

No sound from subwoofer RH.


9 (G/R) Ground Amp. ON sig-nal Input ON — More than 6.5V System does not

work properly.

11 (V) 27 (B/Y) Rear speaker LH Output ON Receive audio

signalNo sound from rear speaker LH.

12 (R/Y) 28 (R/L) Rear speaker RH Output ON Receive audio

signalNo sound from rear speaker RH.

13 (W/R) 29 (L/B) Front tweeter RH Output ON Receive audio

signalNo sound from front tweeter RH.

SKIA0177E

SKIA0177E

SKIA0177E

SKIA0177E

SKIA0177E


AUDIO

AV-51


C

D

E

F

G

H

I

J

L

M

A

B

AV

N

O

P

14 (R/G) 30 (B/R) Front tweeter LH Output ON Receive audio

signalNo sound from front tweeter LH.

15 (L/W) 31 (L/R) Front door speaker LH Output ON Receive audio

signal

No sound from front door speaker LH.

16 (W/B) 32 (G/W) Front door speaker RH Output ON Receive audio

signal

No sound from front door speaker RH.

17 (G) Ground Battery Input — — Battery voltage System does not work properly.


21 (R) 5 (W) Audio sound signal front RH Input ON Receive audio

signal

No sound from front door speaker RH or front tweeter RH.

22 (W) 6 (B) Audio sound signal front LH Input ON Receive audio

signal

No sound from front door speaker LH or front tweeter LH.






SKIA0177E

SKIA0177E

SKIA0177E

SKIA0177E

SKIA0177E


AV-52


IPod Adapter Harness Connector Terminal Layout INFOID:0000000005548856

Terminal and Reference Value for IPod Adapter INFOID:0000000005548857

23 (L) 7 (B/W) Audio sound signal rear RH Input ON Receive audio

signal

No sound from rear speaker assembly RH.

24 (L/R) 8 (L/G) Audio sound signal rear LH Input ON Receive audio

signal

No sound from rear speaker assembly LH.






SKIA0177E

SKIA0177E

AWNIA2015ZZ

Terminal(Wire color) Description

Condition Reference value(Approx.)

+ – Signal name Input/Output

1(G)

13(W) iPod® sound signal LH Output

Ignition switch

ON

When iPod® mode is se-lected.

2(L)

14(R) iPod® sound signal RH Output

Ignition switch

ON


SKIB3609E

SKIB3609E


AUDIO

AV-53


C

D

E

F

G

H

I

J

L

M

A

B

AV

N

O

P

3(GR) Ground ACC power supply Input

Ignition switch ACC

— Battery voltage

4(G) — AV communication signal

(L)Input/Output — — —

5(Y) Ground Battery power supply Input

Ignition switch OFF

— Battery voltage

6(G)

7(SB) iPod® USD signal —

Ignition switch

ON— —

8(O) Ground iPod® battery charge Output

Ignition switch

ONConnected to iPod®. Battery voltage

9(LG) Ground Communication signal

(iPod® adapter→iPod®) OutputIgnition switch

ON

The wave pattern is dis-played just after iPod® con-nection.

NOTE:After the wave pattern display, the value continues Approx 3.3V

10(V) Ground Communication signal

(iPod®→iPod® adapter) InputIgnition switch

ONConnected to iPod®.

11(W) Ground ACCESSORY-IDENTIFY —

Ignition switch

ONConnected to iPod®. 0V

12(R)

Ground iPod® sound signal RH InputIgnition switch

ON


15(GR) — Shield — — — —

16(R) — AV communication signal

(H)Input/Output — — —

17(P) Ground Ground —

Ignition switch

ON— 0V

19(GR) — Shield — — — —




JPNIA0462GB

JPNIA0462GB

SKIB3609E


AV-54


Satellite Radio Tuner Harness Connector Terminal Layout INFOID:0000000005283580

20(O) Ground iPod® battery charge Output

Ignition switch

ONConnected to iPod®. 5.0V

21(V) Ground iPod® connection recogni-

tion signal InputIgnition switch

ON

Not connected to iPod®. 4.0V

Connected to iPod®. 0V

22(Y) Ground ACCESSORY-DETECT —

Ignition switch

ONConnected to iPod®. 0V

23(GR) — Shield — — — —

24(G) Ground iPod® sound signal LH Input

Ignition switch

ON





SKIB3609E

LKIA0735E


AUDIO

AV-55


C

D

E

F

G

H

I

J

L

M

A

B

AV

N

O

P

Terminal and Reference Value for Satellite Radio Tuner INFOID:0000000005283581

Trouble Diagnosis INFOID:0000000005283584

The majority of the audio troubles are the result of outside causes (bad CD, electromagnetic interference,etc.). Check the inspection items below to diagnose the malfunction.

MALFUNCTION WITH RADIO AND CD (BASE AND MID SYSTEM)

Terminal(Wire color)


ConditionVoltage

(Approx.)+ – Ignition

switch Operation

22 (R) 21 (G) Audio signal LH Output ON Receive audio signal.

24 (B) 23 (W) Audio signal RH Output ON Receive audio signal.

28 (L) Ground REQ1(SAT-AUDIO) Output ON Set to the satellite radio

mode

29 (W/R) Ground Communication signal (SAT-AUDIO) Output ON Set to the satellite radio

mode

30 (B/R) Ground Communication signal (AUDIO-SAT) Input ON Set to the satellite radio

mode

32 (Y)Ground

Battery power supply

Input

OFF— Battery voltage

36 (V) ACC power supply ACC

37 — Antenna signal — — —

SKIB3609E

SKIB3609E

SKIB3825E

SKIB3824E

SKIB3826E


AV-56


MALFUNCTION WITH RADIO AND CD (PREMIUM SYSTEM)

FOR RADIO ONLY (PREMIUM SYSTEM)

Symptom Possible cause

Inoperative

• Audio unit power supply circuit check. Refer to AV-58, "Audio Unit (Base and Mid System) Power and Ground Supply Circuit Inspection".

If above check is OK, replace audio unit. Refer to AV-83, "Removal and Instal-lation".

Steering switch does not operate (mid system)

• Steering switch check. Refer to AV-67, "Steering Switch Check (With Blue-tooth)" or AV-69, "Steering Switch Check (Without Bluetooth)".

If above check is OK, replace audio unit. Refer to AV-83, "Removal and Instal-lation".

All speakers do not sound • Audio unit

One or several speakers do not sound

• Front door speaker check. Refer to AV-70, "Sound Is Not Heard from Front Door Speaker or Front Tweeter (Base and Mid System)".

• Rear speaker check. Refer to AV-74, "Sound Is Not Heard from Rear Speak-er (Base and Mid System)".

Poor sound • Audio unit• Speaker

Noisy • Audio unit• Electrical equipment (generator, bonding wire, etc.)

Buzz/rattle sound from speaker

The majority of buzz/rattle sounds are not indicative of an issue with the speak-er, usually something nearby the speaker is causing the buzz/rattle. Refer to "SQUEAK AND RATTLE TROUBLE DIAGNOSIS" in appropriate interior trim section.


Inoperative

• AV control unit power supply circuit check. Refer to AV-58, "Audio Unit (Base and Mid System) Power and Ground Supply Circuit Inspection".

If above check is OK, replace AV control unit. Refer to AV-83, "Removal and Installation".

Steering switch does not operate

• Steering switch check. Refer to AV-67, "Steering Switch Check (With Blue-tooth)".

If above check is OK, replace AV control unit. Refer to AV-83, "Removal and Installation".

All speakers do not sound

• AV control unit• Audio amplifier power supply and ground circuit check. Refer to AV-60, "Au-

dio Amplifier Power and Ground Supply Circuit Inspection".• Audio amplifier ON signal • Audio amplifier

One or several speakers do not sound

• Front door speaker check. Refer to AV-77, "Sound Is Not Heard from Front Door Speaker or Front Tweeter (Premium System with Rockford Fosgate)".

• Rear speaker check. Refer to AV-80, "Sound Is Not Heard from Rear Speak-er Assembly (Premium System with Rockford Fosgate)" or AV-76, "Sound Is Not Heard from Rear Speaker (Premium System without Rockford Fosgate)" .

Poor sound• AV control unit• Audio amplifier• Speaker

Noisy• AV control unit• Audio amplifier • Electrical equipment (generator, bonding wire, etc.)




AUDIO

AV-57


C

D

E

F

G

H

I

J

L

M

A

B

AV

N

O

P

NOTE:The following noise results from variations in field strength, such as fading noise and multi-path noise, orexternal noise from trains and other sources. It is not a malfunction.• Fading noise: This noise occurs because of variations in the field strength in a narrow range due to moun-

tains or buildings blocking the signal.• Multi-path noise: This noise results from the waves sent directly from the broadcast station arriving at the

antenna at a different time from the waves which reflect off mountains or buildings.

FOR CD ONLY

FOR SATELLITE RADIO TUNER ONLY


No sound • AV control unit• Antenna feeder, wiring or connections

Noisy

• AV control unit• AV control unit ground• Antenna feeder, wiring or connections• Noise prevention parts• Electrical equipment• Wire harness of each piece of electrical equipment


The majority of buzz/rattle sounds are not indicative of an issue with the speaker, usually something nearby the speaker is causing the buzz/rattle. Refer to "SQUEAK AND RATTLE TROUBLE DIAGNO-SIS" in appropriate interior trim section.

All radio stations stored in memory are deleted

• AV control unit power supply circuit. Refer to AV-59, "AV Control Unit (Premium System) Power and Ground Supply Circuit Inspec-tion".

• Audio unit


CD cannot be inserted.

• CD• Audio unit

CD cannot be ejected.

The CD cannot be played.

The sound skips, stops suddenly, or is distorted.


Inoperative

• Satellite radio tuner power and ground circuit inspection. Refer to AV-61, "Satellite Radio Tuner Power and Ground Supply Circuit Inspection".

• Satellite radio tuner communication circuit inspection. Refer to AV-61, "Sat-ellite Radio Tuner Communication Circuit Inspection (Mid System)" or AV-63, "Satellite Radio Tuner Communication Circuit Inspection (Premium Sys-tem)".

If above check is OK, replace satellite radio tuner. Refer to AV-83, "Removal and Installation".

Right or left channel does not sound

• Satellite radio tuner right channel audio signal circuit inspection. Refer to AV-66, "Satellite Radio Tuner Right Channel Audio Signal Circuit Inspection (Mid System)" or AV-67, "Satellite Radio Tuner Right Channel Audio Signal Circuit Inspection (Premium System)".

• Satellite radio tuner left channel audio signal circuit inspection. Refer to AV-64, "Satellite Radio Tuner Left Channel Audio Signal Circuit Inspection (Mid System)" or AV-65, "Satellite Radio Tuner Left Channel Audio Signal Circuit Inspection (Premium System)".

If above check is OK, replace satellite radio tuner. Refer to AV-83, "Removal and Installation".

Poor reception• Location of vehicle. Make certain vehicle is in an open area.• Satellite radio antenna or antenna feeder. Refer to AV-89, "Location of An-

tenna".


AV-58


Noise Inspection INFOID:0000000005283585

The vehicle itself can be a source of noise if noise prevention parts or electrical equipment is malfunctioning.Check if noise is caused and/or changed by engine speed, ignition switch turned to each position, and opera-tion of each piece of electrical equipment, and determine the cause.NOTE:The source of the noise can be found easily by listening to the noise while removing the fuses of electricalcomponents, one by one.

TYPE OF NOISE AND POSSIBLE CAUSE

Audio Unit (Base and Mid System) Power and Ground Supply Circuit InspectionINFOID:0000000005283586

1.CHECK FUSE

Check that the following fuses of the audio amplifier (premium system) and audio unit are not blown.

OK or NGOK >> GO TO 2.NG >> If fuse is blown, be sure to eliminate cause of malfunction before installing new fuse. Refer to PG-

16, "Fuse".2.AUDIO UNIT POWER SUPPLY CIRCUIT CHECK

1. Disconnect audio unit connector. 2. Check voltage between the audio unit connector and ground.

Noisy

• Satellite radio tuner ground.• Satellite radio tuner harness shield wires.• Electrical equipment (generator, bonding wire, etc.). Refer to AV-58, "Noise

Inspection".




Occurrence condition Possible cause

Occurs only when engine is ON.

A continuous growling noise occurs. The speed of the noise varies with changes in the engine speed. Ignition components

A whistling noise occurs while the engine speed is high. A booming noise occurs while the engine is running and the lighting switch is ON.

Generator

Noise only occurs when various electrical components are oper-ating.

A cracking or snapping sound occurs with the op-eration of various switches. Relay malfunction, radio malfunction

The noise occurs when various motors are operat-ing.

• Motor case ground• Motor

The noise occurs constantly, not just under certain conditions. • Rear defogger coil malfunction• Open circuit in printed heater

A cracking or snapping sound occurs while the vehicle is being driven, especially when it is vibrating excessively.

• Ground wire of body parts.• Ground due to improper part installation• Wiring connections or a short circuit

Unit Terminals Signal name Fuse No.

Audio unit19 Battery power 31

7 Ignition switch ACC or ON 6


AUDIO

AV-59


C

D

E

F

G

H

I

J

L

M

A

B

AV

N

O

P

OK or NGOK >> GO TO 3.NG >> • Check connector housings for disconnected or loose

terminals.• Repair harness or connector.

3.GROUND CIRCUIT CHECK

Check continuity between audio unit harness connector M43 termi-nals 28 (mid system), 20 and ground.

OK or NGOK >> Inspection End.NG >> • Check connector housings for disconnected or loose


AV Control Unit (Premium System) Power and Ground Supply Circuit InspectionINFOID:0000000005549051

1.CHECK FUSE

Check that the following fuses of the AV control unit are not blown.


3.2.AV CONTROL UNIT POWER SUPPLY CIRCUIT CHECK

1. Disconnect AV control unit connector. 2. Check voltage between the AV control unit connector and ground.

OK or NGOK >> GO TO 3.

Unit

Terminal No.

OFF ACC ON(+)(-)

Connector Terminal

Audio unit M4319 Ground Battery

voltageBattery voltage

Battery voltage

7 Ground 0V Battery voltage

Battery voltage

WKIA5769E

Continuity should exist.

AWNIA1998ZZ


AV control unit19 Battery power 31


Unit

Terminal No.

OFF ACC ON(+)(-)

Connector Terminal

AV control unit M92

19 Ground Battery voltage

Battery voltage

Battery voltage


Battery voltage

WKIA5769E


AV-60


NG >> • Check connector housings for disconnected or loose terminals.• Repair harness or connector.


Check continuity between AV control unit harness connectors M92,M93 terminals 20, 27, 47 and ground.



Audio Amplifier Power and Ground Supply Circuit Inspection INFOID:0000000005549052

1.CHECK FUSE

Check that the following fuses of the audio amplifier are not blown.


3.2.AUDIO AMPLIFIER POWER SUPPLY CIRCUIT CHECK

1. Disconnect audio amplifier connector. 2. Check voltage between audio amplifier connector and ground.




Check continuity between audio amplifier harness connector B44terminals 4, 20 and ground.




AWNIA1999ZZ


Audio amplifier17 Battery power 17

1 Battery power 31

Unit

Terminal No.

OFF ACC ON(+)(-)

Connector Terminal

Audio am-plifier B44

1Ground 0V Battery

voltageBattery voltage17

WKIA3722E


WKIA3723E


AUDIO

AV-61


C

D

E

F

G

H

I

J

L

M

A

B

AV

N

O

P

Satellite Radio Tuner Power and Ground Supply Circuit Inspection INFOID:0000000005283587

1.CHECK FUSES

Check that the following fuses are not blown.


3.2.POWER SUPPLY CIRCUIT CHECK

1. Turn ignition switch OFF.2. Disconnect satellite radio tuner connector B56. 3. Check voltage between the satellite radio tuner and ground.




Inspect satellite radio tuner case ground.OK or NGOK >> Inspection End.NG >> Repair satellite radio tuner case ground.

Satellite Radio Tuner Communication Circuit Inspection (Mid System) INFOID:0000000005283588

1.CHECK HARNESS - 1

1. Turn ignition switch OFF.2. Disconnect satellite radio tuner connector B56 and audio unit connector M45.3. Check continuity between satellite radio tuner harness connec-

tor B56 (A) terminal 28 and audio unit harness connector M45(B) terminal 52.

4. Check continuity between satellite radio tuner harness connec-tor B56 (A) terminal 28 and ground.

OK or NGOK >> GO TO 2.NG >> Repair harness or connector.


Satellite radio tuner32 Battery power 31


Unit

Terminal No.

OFF ACC ON(+)(-)

Connector Terminal

Satellite radio tuner B56

32 Ground Battery voltage

Battery voltage

Battery voltage


Battery voltage

WKIA4539E


Continuity should not exist.

AWNIA2000ZZ


AV-62


2.CHECK HARNESS - 2

1. Check continuity between satellite radio tuner harness connec-tor B56 (A) terminal 29 and audio unit harness connector M45(B) terminal 53.



3.CHECK HARNESS - 3

1. Check continuity between satellite radio tuner harness connec-tor B56 (A) terminal 30 and audio unit harness connector M45(B) terminal 54.



4.CHECK REQ1 SIGNAL

1. Connect satellite radio tuner connector and audio unit connector.2. Turn ignition switch to ACC.3. Check signal between satellite radio tuner harness connector

B56 terminal 28 and ground with CONSULT-III or oscilloscope.

OK or NGOK >> GO TO 5.NG >> Replace audio unit. Refer to AV-83, "Removal and

Installation".

5.CHECK TXD SIGNAL

Check signal between satellite radio tuner harness connector B56terminal 29 and ground with CONSULT-III or oscilloscope.

OK or NGOK >> GO TO 6.NG >> Replace audio unit. Refer to AV-83, "Removal and

Installation".



AWNIA2001ZZ



AWNIA2002ZZ

28 - Ground : Refer to AV-55, "Terminal and Reference Value for Satel-lite Radio Tuner".

WKIA4544E


WKIA4545E


AUDIO

AV-63


C

D

E

F

G

H

I

J

L

M

A

B

AV

N

O

P

6.CHECK RXD SIGNAL


OK or NGOK >> Replace satellite radio tuner. Refer to AV-83, "Removal

and Installation".NG >> Replace audio unit. Refer to AV-83, "Removal and

Installation".

Satellite Radio Tuner Communication Circuit Inspection (Premium System)INFOID:0000000005549769

1.CHECK HARNESS - 1

1. Turn ignition switch OFF.2. Disconnect satellite radio tuner connector B56 and AV control unit connector M96.3. Check continuity between satellite radio tuner harness connec-

tor B56 (A) terminal 28 and AV control unit harness connectorM96 (B) terminal 72.



2.CHECK HARNESS - 2

1. Check continuity between satellite radio tuner harness connec-tor B56 (A) terminal 29 and AV control unit harness connectorM96 (B) terminal 73.



3.CHECK HARNESS - 3


WKIA4546E



AWNIA2005ZZ



AWNIA2006ZZ


AV-64


1. Check continuity between satellite radio tuner harness connec-tor B56 (A) terminal 30 and AV control unit harness connectorM96 (B) terminal 74.



4.CHECK REQ1 SIGNAL

1. Connect satellite radio tuner connector and AV control unit connector.2. Turn ignition switch to ACC.3. Check signal between satellite radio tuner harness connector

B56 terminal 28 and ground with CONSULT-III or oscilloscope.

OK or NGOK >> GO TO 5.NG >> Replace AV control unit. Refer to AV-83, "Removal and

Installation".

5.CHECK TXD SIGNAL


OK or NGOK >> GO TO 6.NG >> Replace AV control unit. Refer to AV-83, "Removal and

Installation".

6.CHECK RXD SIGNAL


OK or NGOK >> Replace satellite radio tuner. Refer to AV-83, "Removal

and Installation".NG >> Replace AV control unit. Refer to AV-83, "Removal and

Installation".

Satellite Radio Tuner Left Channel Audio Signal Circuit Inspection (Mid System)INFOID:0000000005283589

1.CHECK HARNESS



AWNIA2007ZZ


WKIA4544E


WKIA4545E


WKIA4546E


AUDIO

AV-65


C

D

E

F

G

H

I

J

L

M

A

B

AV

N

O

P

1. Turn ignition switch OFF.2. Disconnect satellite radio tuner connector B56 (A) and audio unit connector M45 (B).3. Check continuity between satellite radio tuner and audio unit.

4. Check continuity between satellite radio tuner and ground.


2.CHECK LEFT CHANNEL AUDIO SIGNAL

1. Connect satellite radio tuner and audio unit.2. Turn ignition switch ON.3. Check signal between satellite radio tuner connector B56 termi-

nals 21 and 22 with CONSULT-III or oscilloscope.

OK or NGOK >> Replace audio unit. Refer to AV-83, "Removal and

Installation".NG >> Replace satellite radio tuner. Refer to AV-83, "Removal

and Installation".

Satellite Radio Tuner Left Channel Audio Signal Circuit Inspection (Premium System)INFOID:0000000005549770

1.CHECK HARNESS

1. Turn ignition switch OFF.2. Disconnect satellite radio tuner connector B56 (A) and AV control unit connector M96 (B).3. Check continuity between satellite radio tuner and AV control unit.


Terminals

ContinuitySatellite radio tuner Audio unit

Connector Terminal Connector Terminal

A: B5621

B: M4545

Yes22 46

Terminals

ContinuitySatellite radio tuner—

Connector Terminal

A: B5621

Ground No22

AWNIA2003ZZ

21 - 22 : Refer to AV-55, "Terminal and Reference Value for Sat-ellite Radio Tuner".

WKIA4548E

Terminals

ContinuitySatellite radio tuner AV control unit


A: B5621

B: M9665

Yes22 66

AWNIA2008ZZ


AV-66



2.CHECK LEFT CHANNEL AUDIO SIGNAL

1. Connect satellite radio tuner and AV control unit.2. Turn ignition switch ON.3. Check signal between satellite radio tuner connector B56 termi-


OK or NGOK >> Replace AV control unit. Refer to AV-83, "Removal and


and Installation".

Satellite Radio Tuner Right Channel Audio Signal Circuit Inspection (Mid System)INFOID:0000000005283590

1.CHECK HARNESS

1. Turn ignition switch OFF.2. Disconnect satellite radio tuner connector B56 (A) and audio unit connector M45 (B).3. Check continuity between satellite radio tuner and audio unit.



2.CHECK RIGHT CHANNEL AUDIO SIGNAL

1. Connect satellite radio tuner and audio unit.2. Turn ignition switch ON.

Terminals


Connector Terminal

A: B5621

Ground No22


WKIA4548E

Terminals

ContinuitySatellite radio tuner Audio unit


A: B5623

B: M4547

Yes24 48

Terminals


Connector Terminal

A: B5623

Ground No24

AWNIA2004ZZ


AUDIO

AV-67


C

D

E

F

G

H

I

J

L

M

A

B

AV

N

O

P

3. Check signal between satellite radio tuner connector B56 termi-nals 23 and 24 with CONSULT-III or oscilloscope.

OK or NGOK >> Replace audio unit. Refer to AV-83, "Removal and


and Installation".

Satellite Radio Tuner Right Channel Audio Signal Circuit Inspection (Premium System)INFOID:0000000005549771

1.CHECK HARNESS

1. Turn ignition switch OFF.2. Disconnect satellite radio tuner connector B56 (A) and AV control unit connector M96 (B).3. Check continuity between satellite radio tuner and AV control unit.



2.CHECK RIGHT CHANNEL AUDIO SIGNAL

1. Connect satellite radio tuner and AV control unit.2. Turn ignition switch ON.3. Check signal between satellite radio tuner connector B56 termi-


OK or NGOK >> Replace AV control unit. Refer to AV-83, "Removal and


and Installation".

Steering Switch Check (With Bluetooth) INFOID:0000000005283591

1.CHECK HARNESS


WKIA4550E

Terminals

ContinuitySatellite radio tuner AV control unit


A: B5623

B: M9667

Yes24 68

Terminals


Connector Terminal

A: B5623

Ground No24

AWNIA2009ZZ


WKIA4550E


AV-68


1. Turn ignition switch OFF.2. Disconnect Bluetooth control unit connector B15 and spiral cable connector M30.3. Check continuity between Bluetooth control unit connector B15 (A) terminals 12, 13, and 14 and spiral

cable connector M30 (B) terminals 25, 31, and 33.

4. Check continuity between Bluetooth control unit and ground.

OK or NGOK >> GO TO 2.NG >> Repair harness.

2.CHECK HARNESS

1. Disconnect audio unit connector M43 (mid system) or AV control unit M92 (premium system).2. Check continuity between audio unit connector M43 (mid system) or AV control unit M92 (premium sys-

tem) (A) terminals 6, 15, and 16 and Bluetooth control unit connector B15 (B) terminals 17, 19, and 18.


3.SPIRAL CABLE CHECK

1. Disconnect spiral cable connector M78.2. Check continuity between spiral cable terminals.

OK or NGOK >> GO TO 4.NG >> Replace spiral cable. Refer to SRS-33, "Removal and

Installation".

Terminals

ContinuityA B


B15

12

M30

33

Yes13 31

14 25

Terminals

Continuity(+)(–)

Connector Terminal

B1512

Ground No13

14

WKIA5775E

Terminals

Continuity (A) (B)


M43 (mid system)

M92 (pre-mium sys-

tem)

6

B15

17

Yes15 19

16 18

WKIA5776E

15 - 33 : Continuity should exist.17 - 31 : Continuity should exist.19 - 25 : Continuity should exist.

WKIA5777E


AUDIO

AV-69


C

D

E

F

G

H

I

J

L

M

A

B

AV

N

O

P

4.CHECK STEERING SWITCH RESISTANCE

Check resistance between spiral cable connector M78 terminals.

OK or NGOK >> Inspection End.NG >> Replace steering switch. Refer to AV-83, "Removal and Installation".

Steering Switch Check (Without Bluetooth) INFOID:0000000005283592

1.CHECK HARNESS

1. Turn ignition switch OFF.2. Disconnect audio unit connector M43 and spiral cable connector M30.3. Check continuity between audio unit connector terminal and spi-

ral cable connector terminal.

4. Check continuity between audio unit and ground.


2.SPIRAL CABLE CHECK

1. Disconnect spiral cable connector M78.

Terminal Signal name ConditionResistance

(Ω)(Approx.)

17 19

Seek (down) Depress Seek down switch. 165

Phone/Send Depress Phone/Send switch. 0

Volume (down) Depress volume down switch. 487

15 19

Seek (up) Depress Seek up switch. 165

Phone/End Depress Phone/End switch. 0

Volume (up) Depress volume up switch. 487WKIA5778E

Terminals

ContinuityA B


M43

6

M30

33

Yes15 25

16 31

Terminals

ContinuityA(–)

Connector Terminal

M43

6

Ground No15

16

WKIA5807E


AV-70


2. Check continuity between spiral cable terminals.

OK or NGOK >> GO TO 3.NG >> Replace spiral cable. Refer to SRS-33, "Removal and

Installation".

3.CHECK STEERING SWITCH RESISTANCE

Check resistance between spiral cable connector M78 terminals.

OK or NGOK >> Inspection End.NG >> Replace steering switch. Refer to AV-83, "Removal and Installation".

Sound Is Not Heard from Front Door Speaker or Front Tweeter (Base and Mid System)INFOID:0000000005283593

1.CONNECTOR CHECK

Check the audio unit and speaker connectors for the following:• Proper connection• Damage• Disconnected or loose terminalsIs the inspection result normal?YES >> GO TO 2.NO >> Repair the terminal and connector.

2.HARNESS CHECK

1. Disconnect audio unit connector and front door speaker and front tweeter (mid system) connector (LH orRH).

15 - 33 : Continuity should exist.17 - 31 : Continuity should exist.19 - 25 : Continuity should exist.

WKIA5777E

Terminal Signal name ConditionResistance

(Ω)(Approx.)

17 19

Seek (down) Depress (station) down switch. 165

Power Depress power switch. 0

Volume (down) Depress volume down switch. 487

15 19

Seek (up) Depress (station) up switch. 165

Mode Depress mode switch. 0

Volume (up) Depress volume up switch. 487WKIA5778E


AUDIO

AV-71


C

D

E

F

G

H

I

J

L

M

A

B

AV

N

O

P

2. Check continuity between audio unit harness connector terminaland front door speaker and front tweeter (mid system) harnessconnector terminal.

*: With mid system3. Check continuity between audio unit harness connector terminal

and ground.


3.FRONT SPEAKER SIGNAL CHECK

1. Connect audio unit connector, front door speaker connector and front tweeter (mid system) connector.2. Turn ignition switch to ACC.3. Push “POWER” switch.

Terminals

ContinuityAudio unit Speaker or tweeter


A: M43

2B: M46*

+

Yes

3 -

11B: M47*

+

12 -

2B: D10

+

3 -

11B: D108

+

12 -

Terminals

ContinuityAudio unit —

Connector Terminal

A: M43

2

Ground No3

11

12

WKIA5444E


AV-72


4. Check the signal between audio unit connector terminals withCONSULT-III or oscilloscope.

OK or NGOK >> Replace front speaker. Refer to AV-83, "Removal and

Installation".NG >> Replace audio unit. Refer to AV-83, "Removal and

Installation".

Sound Is Not Heard from Front Door Speaker or Front Tweeter (Premium System with-out Rockford Fosgate) INFOID:0000000005549044

1.CONNECTOR CHECK

Check the AV control unit and speaker connectors for the following:• Proper connection• Damage• Disconnected or loose terminalsIs the inspection result normal?YES >> GO TO 2.NO >> Repair the terminal and connector.

2.HARNESS CHECK

1. Disconnect AV control unit connector and front door speaker and front tweeter connector (LH or RH).

Terminals

Condi-tion

Referencesignal

(+) (-)

Con-nector

Termi-nal

Con-nector

Termi-nal

M43

2

M43

3

Receive audio signal11 12

WKIA5853E

SKIA0177E


AUDIO

AV-73


C

D

E

F

G

H

I

J

L

M

A

B

AV

N

O

P

2. Check continuity between AV control unit harness connector ter-minal and front door speaker and front tweeter harness connec-tor terminal.

3. Check continuity between AV control unit harness connector ter-minal and ground.



1. Connect AV control unit connector, front door speaker connector and front tweeter connector.2. Turn ignition switch to ACC.3. Push “POWER” switch.

Terminals

ContinuityAV control unit Speaker or tweeter


A: M92

2B: M46

+

Yes

3 -

11B: M47

+

12 -

2B: D10

+

3 -

11B: D108

+

12 -

Terminals

ContinuityAV control unit —

Connector Terminal

A: M92

2

Ground No3

11

12

WKIA5444E


AV-74


4. Check the signal between AV control unit connector terminalswith CONSULT-III or oscilloscope.

OK or NGOK >> Replace front speaker. Refer to AV-83, "Removal and

Installation".NG >> Replace AV control unit. Refer to AV-83, "Removal and

Installation".

Sound Is Not Heard from Rear Speaker (Base and Mid System) INFOID:0000000005283594

1.CONNECTOR CHECK

Check the audio unit and speaker connectors for the following:• Proper connection• Damage• Disconnected or loose terminalsIs the inspection result normal?YES >> GO TO 2.NO >> Repair the terminal and connector.

2.HARNESS CHECK

1. Disconnect audio unit connector and rear speaker connector.

Terminals

Condi-tion

Referencesignal

(+) (-)

Con-nector

Termi-nal

Con-nector

Termi-nal

M92

2

M92

3


WKIA5853E

SKIA0177E


AUDIO

AV-75


C

D

E

F

G

H

I

J

L

M

A

B

AV

N

O

P

2. Check continuity between audio unit harness connector terminaland rear speaker harness connector terminal.

3. Check continuity between audio unit harness connector terminaland ground.


3.REAR SPEAKER SIGNAL CHECK

1. Connect audio unit connector and rear speaker connector.2. Turn ignition switch to ACC.3. Push “POWER” switch.4. Check the signal between audio unit harness connector termi-

nals with CONSULT-III or oscilloscope.

OK or NGOK >> Replace speaker. Refer to AV-83, "Removal and Instal-

lation".NG >> Replace audio unit. Refer to AV-83, "Removal and

Installation".

Terminals

ContinuityAudio unit Speaker


A: M43

4B: B27

+

Yes5 -

13B: B39

+

14 -

Terminals

ContinuityAudio unit —

Connector Terminal

A: M43

4

Ground No5

13

14

WKIA5353E

Terminals

Condi-tion

Referencesignal

(+) (-)

Con-nec-tor

Termi-nal

Con-nec-tor

Termi-nal

M43

4

M43

5

Re-ceive audio signal

13 14

WKIA5808E

SKIA0177E


AV-76


Sound Is Not Heard from Rear Speaker (Premium System without Rockford Fosgate)INFOID:0000000005549045

1.CONNECTOR CHECK


2.HARNESS CHECK

1. Disconnect AV control unit connector and rear speaker connector.2. Check continuity between AV control unit harness connector ter-

minal and rear speaker harness connector terminal.




1. Connect AV control unit connector and rear speaker connector.2. Turn ignition switch to ACC.3. Push “POWER” switch.

Terminals

ContinuityAV control unit Speaker


A: M92

4B: B27

+

Yes5 -

13B: B39

+

14 -

Terminals


Connector Terminal

A: M92

4

Ground No5

13

14

WKIA5353E


AUDIO

AV-77


C

D

E

F

G

H

I

J

L

M

A

B

AV

N

O

P

4. Check the signal between AV control unit harness connector ter-minals with CONSULT-III or oscilloscope.

OK or NGOK >> Replace speaker. Refer to AV-83, "Removal and Instal-

lation".NG >> Replace AV control unit. Refer to AV-83, "Removal and

Installation".

Sound Is Not Heard from Front Door Speaker or Front Tweeter (Premium System with Rockford Fosgate) INFOID:0000000005283595

1.CONNECTOR CHECK


2.HARNESS CHECK

1. Turn ignition switch OFF.2. Disconnect audio amplifier connector B43 and suspect speaker connector.

Terminals

Condi-tion

Referencesignal

(+) (-)

Con-nec-tor

Termi-nal

Con-nec-tor

Termi-nal

M92

4

M92

5


13 14

WKIA5808E

SKIA0177E


AV-78


3. Check continuity between audio amplifier harness connector ter-minal and suspect speaker harness connector terminal.

4. Check continuity between audio amplifier harness connector ter-minal and ground.



1. Connect audio amplifier connector B43 and suspect speaker connector.2. Turn ignition switch to ACC.3. Push “POWER” switch.4. Check the signal between audio amplifier harness connector ter-

minals with CONSULT-III or oscilloscope.

Terminals

ContinuityAudio amplifier Speaker or tweeter


B43

15D10

+

Yes

31 -

16D108

+

32 -

14M46

-

30 +

13M47

-

29 +

Terminals

ContinuityAudio amplifier —

Connector Terminal

B43

13

Ground No

14

15

16

29

30

31

32

WKIA3372E

Terminals

Condi-tion

Referencesignal

(+) (-)

Con-nector

Termi-nal

Con-nector

Termi-nal

B43

13

B43

29


14 30

15 31

16 32

LKIA0602E

SKIA0177E


AUDIO

AV-79


C

D

E

F

G

H

I

J

L

M

A

B

AV

N

O

P

OK or NGOK >> Replace suspect speaker. Refer to AV-83, "Removal and Installation".NG >> GO TO 4.

4.HARNESS CHECK

1. Turn ignition switch OFF.2. Disconnect AV control unit connector M94 and audio amplifier connector B43.3. Check continuity between AV control unit harness connector ter-

minals and audio amplifier harness connector terminals.

4. Check continuity between AV control unit harness connector ter-minals and ground.

OK or NGOK >> GO TO 5.NG >> • Check connector housings for disconnected or loose terminals.

• Repair harness or connector.5.FRONT SPEAKER SIGNAL CHECK

1. Connect AV control unit connector and audio amplifier connector.2. Turn ignition switch to ACC.3. Push “POWER” switch.

Terminals

ContinuityAV control unit Audio amplifier


A: M94

53

B: B43

6

Yes59 22

57 5

63 21

Terminals


Connector Terminal

A: M94

53

Ground No57

59

63

AWNIA2016ZZ


AV-80


4. Check the signal between AV control unit harness connector ter-minals with CONSULT-III or oscilloscope.

OK or NGOK >> Replace audio amplifier. Refer to AV-83, "Removal and


Installation".

Sound Is Not Heard from Rear Speaker Assembly (Premium System with Rockford Fosgate) INFOID:0000000005283596

1.CONNECTOR CHECK


2.HARNESS CHECK

1. Turn ignition switch OFF.2. Disconnect audio amplifier connectors B43, B44 and suspect speaker connector.

Terminals

Condi-tion

Referencesignal

(+) (-)

Con-nector

Termi-nal

Con-nector

Termi-nal

M94

59

M94

53


AWNIA2017ZZ

SKIA0177E


AUDIO

AV-81


C

D

E

F

G

H

I

J

L

M

A

B

AV

N

O

P

3. Check continuity between audio amplifier harness connector ter-minal and suspect speaker harness connector terminal.

4. Check continuity between audio amplifier harness connector ter-minals and ground.



1. Connect audio amplifier connectors B43, B44 and suspect speaker connector.2. Turn ignition switch to ACC.3. Push “POWER” switch.

Terminals

ContinuityAudio amplifier Speaker


A: B43

11C: B40

4

Yes

27 3

12C: B38

4

28 3

B: B44

2C: B40

2

18 1

3C: B38

2

19 1

Terminals

ContinuityAudio amplifier —

Connector Terminal

A: B43

11

Ground No

27

12

28

B: B44

2

18

3

19

WKIA5816E


AV-82


4. Check the signal between audio amplifier harness connector ter-minals with CONSULT-III or oscilloscope.

OK or NGOK >> Replace suspect speaker. Refer to AV-83, "Removal

and Installation".NG >> GO TO 4.

4.HARNESS CHECK

1. Turn ignition switch OFF.2. Disconnect AV control unit connector M94 and audio amplifier connector B43.3. Check continuity between AV control unit harness connector ter-

minals and audio amplifier harness connector terminals.


OK or NGOK >> GO TO 5.NG >> • Check connector housings for disconnected or loose terminals.

• Repair harness or connector.5.REAR SPEAKER SIGNAL CHECK

1. Connect AV control unit connector M94 and audio amplifier connector B43.

Terminals

Condi-tion

Referencesignal

(+) (-)

Con-nec-tor

TerminalCon-nec-tor

Terminal

A: B43

11 A: B43

27


12 28

B: B44

2

B: B44

18

3 19

WKIA5817E

SKIA0177E

Terminals

ContinuityAV control unit Audio amplifier


A: M94

54

B: B43

8

Yes60 24

58 7

64 23

Terminals


Connector Terminal

A: M94

54

Ground No58

60

64

AWNIA2018ZZ


AUDIO

AV-83


C

D

E

F

G

H

I

J

L

M

A

B

AV

N

O

P

2. Turn ignition switch to ACC.3. Push “POWER” switch.4. Check the signal between audio unit harness connector termi-

nals with CONSULT-III or oscilloscope.

OK or NGOK >> Replace audio amplifier. Refer to AV-83, "Removal and


Installation".

Removal and Installation INFOID:0000000005283597

AUDIO UNIT

Terminals

Condi-tion

Referencesignal

(+) (-)

Con-nector Terminal Con-

nector Terminal

M94

60

M94

54


64 58

AWNIA2019ZZ

SKIA0177E

LKIA0867E


AV-84


Removal1. Disconnect the battery negative terminal.2. Remove the cluster lid C. Refer to IP-11.3. Remove the display unit to audio unit harness.4. Remove the cluster lid C bracket screws.5. Remove the audio unit and display unit (if equipped).InstallationInstallation is in the reverse order of removal.

FRONT TWEETERRemoval1. Remove the front pillar garnish. Refer to EI-34.2. Remove the front tweeter grille.3. Remove the front tweeter screws (A), disconnect the front

tweeter connector and remove the front tweeter (1).

InstallationInstallation is in the reverse order of removal.

FRONT DOOR SPEAKERRemoval1. Remove the front door finisher. Refer to EI-31.2. Remove the front door speaker screws (A), disconnect the front

door speaker connector and remove the front door speaker (1).


REAR SPEAKERRemoval1. Remove the rear parcel shelf finisher. Refer to EI-38, "Removal and Installation".

1. Display unit 2. Display unit connector 3. Audio unit connector4. Audio unit A. Cluster lid C bracket screws

LKIA0855E

LKIA0856E


AUDIO

AV-85


C

D

E

F

G

H

I

J

L

M

A

B

AV

N

O

P

2. Remove the rear speaker screws (A), disconnect the rearspeaker connector and remove the rear speaker (1).


AUDIO AMPLIFIER

Removal1. Disconnect the battery negative terminal.2. Slide the RH front seat toward the front to remove the audio amplifier rear bolts. 3. Slide the RH front seat toward the rear to remove the audio amplifier front bolts. 4. Disconnect the audio amplifier connectors and remove the audio amplifier.InstallationInstallation is in the reverse order of removal.

SATELLITE RADIO TUNER

LKIA0857E

1. Audio amplifier 2. Audio amplifier connectors A. Bolts⇒ Front

LKIA0865E


AV-86


Removal1. Remove the luggage side finisher (LH). Refer to EI-44, "Removal and Installation".2. Remove the satellite radio tuner bolts.3. Disconnect the satellite radio tuner connector and remove the satellite radio tuner. 4. If necessary, remove the satellite radio tuner bracket bolts (A)

and remove the satellite radio tuner brackets (1).


STEERING WHEEL AUDIO CONTROL SWITCHESRemoval1. Remove the driver air bag module. Refer to SRS-31, "Removal and Installation".

1. Satellite radio tuner connector 2. Satellite radio tuner B. Bolts⇒ Front

LKIA0858E

LKIA0859E


AUDIO

AV-87


C

D

E

F

G

H

I

J

L

M

A

B

AV

N

O

P

2. Remove the steering wheel audio control switch screws (A) andremove the steering wheel audio control switches (1).


LKIA0860E


AV-88

< SERVICE INFORMATION > [AUDIO WITHOUT NAVIGATION]USB CONNECTOR AND AUX JACK

USB CONNECTOR AND AUX JACKRemoval and Installation INFOID:0000000005485390

REMOVAL1. Remove the center console assembly. Refer to IP-12, "Removal and Installation".2. Push the pawl from the back of the center console to remove the

USB connector and aux jack (1).

INSTALLATIONInstallation is in the reverse order of removal.

ALNIA1209ZZ


AUDIO ANTENNA

AV-89


C

D

E

F

G

H

I

J

L

M

A

B

AV

N

O

P

AUDIO ANTENNALocation of Antenna INFOID:0000000005283598

Removal and Installation of Roof Antenna INFOID:0000000005283599

REMOVAL1. Partially remove the rear body side welts. Refer to EI-41, "Removal and Installation".2. Remove rear pillar finishers. Refer to EI-41, "Removal and Installation".3. Remove rear assist grip (LH). Refer to EI-41, "Removal and Installation".4. Remove three headliner rear clips. Pull down the rear part of the headliner to reposition out of the way.

CAUTION:Use care when repositioning headliner to avoid causing damage.

1. Roof antenna 2. Roof antenna base connectors 3. Antenna feeder4. Antenna feeder connector 5. Audio unit (base and mid system)

AV control unit (premium system)6. Roof antenna base

7. Satellite radio tuner antenna feeder connector

8. Satellite radio tuner antenna feeder 9. Satellite radio tuner antenna feeder connector

10. Satellite radio tuner A. Antenna feeder clips B. Satellite radio tuner antenna feeder clips

LKIA0862E


AV-90

< SERVICE INFORMATION > [AUDIO WITHOUT NAVIGATION]AUDIO ANTENNA

5. Disconnect the roof antenna harness connectors (B).6. Remove the roof antenna nut (A) and remove the roof antenna

(1).

INSTALLATIONInstallation is in the reverse order of removal.

LKIA0863E


TELEPHONE

AV-91


C

D

E

F

G

H

I

J

L

M

A

B

AV

N

O

P

TELEPHONEComponent Parts and Harness Connector Location INFOID:0000000005283600

System Description INFOID:0000000005283601

BLUETOOTH® HANDS-FREE PHONE SYSTEMRefer to the Owner's Manual for Bluetooth telephone system operating instructions.NOTE:Cellular telephones must have their wireless connection set up (paired) before using the Bluetooth telephonesystem.

Bluetooth telephone system allows users who have a Bluetooth cellular telephone to make a wireless connec-tion between their cellular telephone and the Bluetooth control unit. Hands-free cellular telephone calls can be

AWNIA1983GB

1. Bluetooth control unit B15, B62 2. Steering wheel audio control switches

3. Microphone R4

4. Combination meter M24 5. Audio unit M43, M53 (with mid system)

6. AV control unit M92, M93 (with premium system)


AV-92

< SERVICE INFORMATION > [AUDIO WITHOUT NAVIGATION]TELEPHONE

sent and received. Some Bluetooth cellular telephones may not be recognized by the Bluetooth control unit.When a cellular telephone or the Bluetooth control unit is replaced, the telephone must be paired with theBluetooth control unit. Different cellular telephones may have different pairing procedures. Refer to the cellulartelephone operating manual.Bluetooth Telephone System Diagram

Bluetooth Control UnitWhen the ignition switch is turned to ACC or ON, the Bluetooth con-trol unit will power up. During power up, the Bluetooth control unit isinitialized and performs various self checks. Initialization may takeup to 20 seconds. If a phone is present in the vehicle and paired withthe Bluetooth control unit, Nissan Voice Recognition will thenbecome active. Bluetooth telephone functions can be turned offusing the Nissan Voice Recognition system.

Steering Wheel Audio Control SwitchesWhen buttons on the steering wheel audio control switch arepushed, the resistance in steering wheel audio control switch circuitchanges depending on which button is pushed. The Bluetooth con-trol module uses this signal to perform various functions while navi-gating through the voice recognition system.The following functions can be performed using the steering wheelaudio control switch:• Initiate Self Diagnosis of the Bluetooth telephone system• Start a voice recognition session• Answer and end telephone calls• Adjust the volume of calls

Volume Switch (with mid system)

AWNIA1984GB

WKIA5781E

WKIA5783E


TELEPHONE

AV-93


C

D

E

F

G

H

I

J

L

M

A

B

AV

N

O

P

Call volume can be adjusted using the audio unit volume switch.

Volume Switch (with premium system)Call volume can be adjusted using the AV control unit volume switch.

Bluetooth MicrophoneThe Bluetooth microphone is located in the roof console assembly.The Bluetooth microphone sends a signal to the Bluetooth controlunit. The Bluetooth microphone can be actively tested during self-diagnosis.

Audio Unit (with mid system)The audio unit receives signals from the Bluetooth control unit andsends audio signals to the speakers.

AV Control Unit (with premium system)

AWNIA1985GB

AWNIA1986GB

AWNIA1987GB

AWNIA1985GB


AV-94


The AV control unit receives signals from the Bluetooth control unitand sends audio signals to the speakers.

AWNIA1986GB


TELEPHONE

AV-95


C

D

E

F

G

H

I

J

L

M

A

B

AV

N

O

P

Wiring Diagram - H/PHON - INFOID:0000000005283602

MID SYSTEM

AANWA0207GB


AV-96


AANWA0208GB


TELEPHONE

AV-97


C

D

E

F

G

H

I

J

L

M

A

B

AV

N

O

P

PREMIUM SYSTEM

AANWA0209GB


AV-98


AANWA0210GB


ELECTRICAL AV A - JustAnswer › DoritoWhatz › ff5c7cd7-0... · • Do not use electrical test...

Documents

Transcript of ELECTRICAL AV A - JustAnswer › DoritoWhatz › ff5c7cd7-0... · • Do not use electrical test...