396396

Receiver Driers - TECHNICAL INFORMATION

Flare to Flare

Switch Plug

SightGlass

Male Insert O’Ring to

Female O’Ring

SightGlass

Indication of Inlet Side

AccessPort

Male Insert O’Ring to

Male Insert O’Ring

SwitchPlug(s)

SightGlass

Indication of Inlet Side

Female O’Ring to

Female O’Ring

SightGlass

Female O’Ring to Barb

MountingBracket Pad Type

LocatingHoles

MountHoles

Inlet & OutletPorts

Height

Diameter

Measurement Procedure

Abbreviations

FOR = Female O’RingFSL = Female Spring LockMF = Male FlareMIOR = Male Insert O’RingMO = Male O’RingMSL = Male Spring Lock

Desiccant Types and Refrigerant Suitability

XH5 - Suitable for R12 only

XH7 - Suitable for R12 and R134a

XH9 - Suitable for R12, R134a and blend refrigerants

All the receiver driers listed within this catalogue are XH7 or where possible XH9 desiccant.

Code of Practice

The code of practice as released by the Department of Environment, Water, Heritage and the Arts, released in 2008

under items 17 & 18 regarding Pressure Relief Valves and Fusible Plugs in Receiver Driers is quoted below.

17. Pressure Relief - It is not acceptable to use pressure relief devices as the only means of protection against over

pressurisation. Wherever practicable any vehicle requiring servicing that is only fitted with a pressure relief valve shall be

fitted with a high/low pressure cut-out switch.

18. Filter Drier - Whenever the refrigerant system is opened, the filter drier or accumulator, when fitted, shall be replaced

in accordance with the manufacturers instructions. Where the manufacturer has not issued instructions the units shall be

replaced whenever the system is opened. The filter drier shall not incorporate a fusible plug unless an alternative type

is not manufactured.

NOTE: In certain instances it is acceptable to use filter driers with pressure relief valves and fuse plugs. Vehicle manufacturers

may still specify these features as part of the original equipment, usually as a last line of defence against damage to expensive

air conditioning componentry. If these features are incorporated into the receiver drier, it can only be used in conjunction with

a high/low pressure cut out switch.

Contents Index 397397

Receiver Driers - TECHNICAL INFORMATION

Accumulators - Basic Types

Typical Accumulators

Accumulators are used in orifice tube systems. They are usually much larger than receiver driers, as they act as

a catchment reservoir to ensure that no liquid refrigerant reaches the compressor. Accumulators are installed

between the evaporator and the compressor.

Generally, accumulators are not full flow filters. Some simply have desiccant bags.

Correct installation is critical to ensure that liquid refrigerant does not enter the compressor.

Driers - Basic Types

Receiver driers are used in standard thermostatic expansion valve (TX valve) systems and are situated between

the condenser and the TX valve at the evaporator.

Note that all upright and some in-line type receiver driers have liquid pick up tubes. Some in-line driers do not

have pick-up tubes and are designed to be mounted vertically. Correct installation to ensure liquid refrigerant

flow to the TX valve is critical.

Correct flow direction and mounting position are essential on all driers - check before installation.

Typical In-line Type Receiver Driers

Filter & Desiccant

Inlet Inlet

Liquid Refrigerant

Reservoir

Liquid Pick-up Tube

with Filter Screen

Outlet

Typical Upright Type Receiver Driers

Inlet

Filter & Desiccant Filter Pads

Liquid Refrigerant

Reservoir

Liquid Flow

NOTE: Illustrations are a reference only

Outlet

Inlet

Service Ports

Liquid Refrigerant

Reservoir

Filter Pads

& Desiccant

Splash

Shield Splash Shield

Inlet

Liquid Refrigerant

Reservoir

Desiccant

Bags

Outlet

Service Ports

Driers & Accumulators

Liquid Pick-up Tube

Contents Index

398

Receiver Driers to suit ALFA ROMEO to AUDI

• Fitting: Inlet Pad

RDX281

• Fitting: Outlet Pad

• Height: 159mm

• Diameter: 60mm

To suit Alfa Romeo 156

2/1999 >

• Fitting: Inlet 3/8” No. 6 FOR

RDX340

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 270mm

• Diameter: 76mm

Top Bottom

• 1 x switch port

To suit Alfa Romeo 164

6/1987 - 9/1998

• Fitting: Inlet 3/8” No. 6 MIOR

RDX379

• Fitting: Outlet 3/8” No. 6 FIOR

• Height: 200mm

• Diameter: 63mm

• 1/8” screwed plug on right

of inlet

To suit Alfa Romeo 33

3/1984 - 11/1992

• Fitting: Inlet 3/8” No. 6 MIOR

RDX401

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 257mm

• Diameter: 70mm

• Switch port on top

• Sight glass on right of inlet

• H.P.R.V. left of inlet

To suit Allison Chalmers Tractors

• Fitting: Inlet 3/8” No. 6 MIOR

RDX402

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 257mm

• Diameter: 70mm

• 1 x switch port left of inlet

• H.P.R.V. right of inlet

To suit Allison Chalmers Tractors

• Fitting: Inlet 3/8” No. 6 MF

RDX512

• Fitting: Outlet 3/8” No. 6 MF

• Height: 156mm

• Diameter: 76mm

To suit American Mark IV Rooftop System

• Fitting: Inlet 3/8” No. 6 MIOR

RDX379

• Fitting: Outlet 3/8” No. 6 FIOR

• Height: 200mm

• Diameter: 63mm

• 1/8” screwed plug on right

of inlet

To suit Audi 100CD, 100LS

• Fitting: Inlet 3/4” No. 12 FIOR

RDX377

• Fitting: Outlet 3/4” No. 12 MIOR

• Height: 230mm

• Diameter: 93mm

• Imperial Fittings

To suit Audi 80 2.0 / 2.6 / 2.8L

1998 >

• Fitting: Inlet M28 x 1.5 FIOR

RDX375

• Fitting: Outlet M28 x 1.5 MIOR

• Height: 203mm

• Diameter: 94mm

• Metric Fittings

To suit Audi 80, 2.0, 2.6, 2.8L

11/1992 - 7/1996

• Fitting: Inlet Pad

RDX378

• Fitting: Outlet Pad

• Height: 160mm

• Diameter: 60mm

To suit Audi A3

5/1997 - 6/2004

BottomTop

Contents Index 399

Receiver Driers to suit AUDI to BMW

• Fitting: Inlet M28 x 1.5 FIOR

RDX375

• Fitting: Outlet M28 x 1.5 MIOR

• Height: 203mm

• Diameter: 94mm

• Metric Fittings

To suit Audi A4 1/1995 - 9/2001, A6 1/1997 - 3/1999

Cabriolet 5/1991 - 8/2000

• Fitting: Inlet Pad

RDX055

• Fitting: Outlet Pad

• Height: 161mm

• Diameter: 64mm

To suit BMW 3 Series E46

2/1998 >

• Fitting: Inlet Pad

RDX056

• Fitting: Outlet Pad

• Height: 97mm

• Diameter: 100mm

• Captive O’Ring

To suit BMW 3 Series E36

6/1997 - 8/2000

• Fitting: Inlet Pad

RDX045

• Fitting: Outlet Pad

• Height: 97mm

• Diameter: 100mm

To suit BMW 3 Series E36

9/1990 - 6/1997

• Fitting: Inlet 3/8” No. 6 MIOR

RDX047

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 180mm

• Diameter: 76mm

• 1 x access port

To suit BMW 3 Series 318i E30

9/1989 - 6/1994

• Fitting: Inlet 3/8” No. 6 MIOR

RDX043

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 179mm

• Diameter: 74mm

• 1 x access port

• 1 x sight glass

• 2 x switch ports

To suit BMW 3 Series 323i E30

9/1982 - 8/1989

• Fitting: Inlet 1/2” No. 8 MIOR

RDX041

• Fitting: Outlet 1/2” No. 8 MIOR

• Height: 174mm

• Diameter: 74mm

• 1 x access port

• 1 switch port

To suit BMW 3 & 7 Series

1977 - 1986

• Fitting: Inlet 5/16” No. 5 MIOR

RDX040

• Fitting: Outlet 5/16” No. 5 MIOR

• Height: 203mm

• Diameter: 60mm

• 2 x switch ports

To suit BMW 3 Series

Denso System

RDX054

• Length: 408mm

To suit BMW 5 Series E60

10/2003 >

• Fitting: Inlet Pad

RDX055

• Fitting: Outlet Pad

• Height: 161mm

• Diameter: 64mm

To suit BMW 5 Series E39

2/1998 >

Contents Index

400

Receiver Driers to suit BMW

• Fitting: Inlet Pad

RDX053

• Fitting: Outlet Pad

• Height: 198mm

• Diameter: 89mm

To suit BMW 5 Series E39

9/1997 >

• Fitting: Inlet Pad

RDX051

• Fitting: Outlet Pad

• Height: 191mm

• Diameter: 89mm body

• Captive O’Ring

To suit BMW 5 Series E39

10/1997 - 9/1998

• Fitting: Inlet Pad

RDX052

• Fitting: Outlet Pad

• Height: 191mm

• Diameter: 89mm body

To suit BMW 5 Series E39

11/1995 - 9/1997

• Fitting: Inlet Pad

RDX044

• Fitting: Outlet Pad

• Height: 175mm

• Diameter: 94mm

• 1 x access port

• H.P.R.V.

• 1 x switch port

To suit BMW 5 Series E34

2/1989 - 1/1997

• Fitting: Inlet 1/2” No. 8 MIOR

RDX042

• Fitting: Outlet 1/2” No. 8 MIOR

• Height: 202mm

• Diameter: 75mm

• 1 x access port

• 1 x switch port

To suit BMW 5 & 6 Series

1982 - 1987

• Fitting: Inlet Pad

RDX055

• Fitting: Outlet Pad

• Height: 161mm

• Diameter: 64mm

To suit BMW 7 Series E38

11/1998 - 11/2001

• Fitting: Inlet Pad

RDX046

• Fitting: Outlet Pad

• Height: 189mm

• Diameter: 89mm body

To suit BMW 7 Series E38

10/1994 - 9/1997

• Fitting: Inlet Pad

RDX044

• Fitting: Outlet Pad

• Height: 175mm

• Diameter: 94mm

• 1 x access port

• H.P.R.V.

• 1 x switch port

To suit BMW 7 Series E32

1/1989 - 9/1994

• Fitting: Inlet Pad

RDX055

• Fitting: Outlet Pad

• Height: 161mm

• Diameter: 64mm

To suit BMW X3 E83 Diesel & Petrol

1/2004 >

• Fitting: Inlet Pad

RDX056

• Fitting: Outlet Pad

• Height: 97mm

• Diameter: 100mm

• Captive O’Ring

To suit BMW Z3 2.2i & 3.0i

6/1997 >

Contents Index 401

Receiver Driers to suit BMW to CATERPILLAR

• Fitting: Inlet Pad

RDX055

• Fitting: Outlet Pad

• Height: 161mm

• Diameter: 64mm

To suit BMW Z4 E85

2/2003>

• Fitting: Inlet 3/8” No. 6 MIOR

RDX402

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 257mm

• Diameter: 70mm

• 1 x switch port left of inlet

• H.P.R.V. right of inlet

To suit Case Tractor

• Fitting: Inlet 3/8” No. 6 MF

RDX403

• Fitting: Outlet 3/8” No. 6 MF

• Height: 161mm

• Diameter: 101mm

To suit Case Tractor

• Fitting: Inlet 3/8” No. 6 MIOR

RDX404

• Fitting: Outlet 3/8” No. 6 FIOR

• Height: 198mm

• Diameter: 100mm

Top Bottom

To suit Case Tractor

• Fitting: Inlet 3/8” No. 6 MIOR

RDX401

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 257mm

• Diameter: 70mm

• 1 x switch port on top

• Sight glass on right of inlet

• H.P.R.V. left of inlet

To suit Case Tractors 70, 90, 94, 96

• Fitting: Inlet 3/8” No. 6 MIOR

RDX061

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 168mm

• Diameter: 76mm

• 1 x switch port left of inlet

• H.P.R.V. right of inlet

To suit Caterpillar

• Fitting: Inlet 3/8” No. 6 MF

RDX062

• Fitting: Outlet 3/8” No. 6 MF

• Height: 201mm

• Diameter: 101mm

To suit Caterpillar

• Fitting: Inlet 3/8” No. 6 MIOR

RDX063

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 196mm

• Diameter: 101mm

• 1 x male switch port

• Moisture indicator

• Comes with pressure switch

To suit Caterpillar

• Fitting: Inlet 3/8” No. 6 MF

RDX064

• Fitting: Outlet 3/8” No. 6 MF

• Height: 148mm

• Diameter: 76mm

• 2 x switch port

To suit Caterpillar

• Fitting: Inlet Quick Connect

RDX066

• Fitting: Outlet Quick Connect

• Height: 199mm

• Diameter: 101mm

• Includes pressure switch

• Moisture indicator

• Pressure Switch PSX001

To suit Caterpillar

Contents Index

402

Receiver Driers to suit CATERPILLAR to CHRYSLER

• Fitting: Inlet 3/4” No. 12 FIOR

RDX069

• Fitting: Outlet 3/4” No. 12 FIOR

• Height: 220mm

• Diameter: 88mm to 93mm

• 2 x 1/4” switch ports

To suit Caterpillar

• Fitting: Inlet Quick Connect

RDX070

• Fitting: Outlet Quick Connect

• Height: 350mm

• Diameter: 64mm

To suit Caterpillar

• Fitting: Inlet 3/8” No. 6 MIOR

RDX071

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 195mm

• Diameter: 101mm

• 1 x switch port left of inlet

• Pressure Switch

To suit Caterpillar

• Fitting: Inlet Quick Connect

RDX073

• Fitting: Outlet Quick Connect

• Height: 350mm

• Diameter: 64mm

To suit Caterpillar

• Fitting: Inlet 3/8” No. 6 MIOR

RDX060

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 148mm

• Diameter: 76mm

• 2 x switch port on top

• To convert to flare - use

2 x AFX2640

To suit Caterpillar

• Fitting: Inlet M27 x 1.5 FIOR

RDX067

• Fitting: Outlet M27 x 1.5 FIOR

• Height: 215mm

• Diameter: 90mm

To suit Caterpillar 12H Grader

• Fitting: Inlet Pad

RDX065

• Fitting: Outlet Pad

• Height: 229mm

• Diameter: 75mm

• Pressure Switch PSX043

(not included)

To suit Caterpillar 325

• Fitting: Inlet 3/8” No. 6 MIOR

RDX140

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 445mm

• Diameter: 50mm

• To convert to flare use

2 x AFX6240

To suit Caterpillar Early

• Fitting: Inlet Pad

RDX906

• Fitting: Outlet Pad

• Height: 172mm

• Diameter: 60mm

To suit Chrysler Neon PL

9/1999 - 9/2002

• Fitting: Inlet 3/8” No. 6 MIOR

RDX903

• Fitting: Outlet 3/8” No. 6 FIOR

• Height: 150mm

• Diameter: 63mm

• R134a charge port

To suit Chrysler Neon 2.0L

8/1996 - 9/2002

Top Bottom

Contents Index 403

Receiver Driers to suit CHRYSLER to DAEWOO

• Fitting: Inlet 3/8” No. 6 MIOR

RDX899

• Fitting: Outlet 3/8” No. 6 FOR

• Height: 170mm

• Diameter: 65mm

• R134a charge port

To suit Chrysler Neon

5/1994 - 8/1999

• Fitting: Inlet Pad

RDX935

• Fitting: Outlet Pad

• Height: 200mm

• Diameter: 90mm

• Switch Port

To suit Chrysler PT Cruiser 2.0 & 2.4L

7/2000 - 3/2009

• Fitting: Inlet Pad

RDX906

• Fitting: Outlet Pad

• Height: 172mm

• Diameter: 60mm

To suit Chrysler Voyager GS 3.3L V6 2/1997 - 6/2001

Grand Voyager 1997 - 2006

• Fitting: Inlet 3/8” No. 6 MIOR

RDX402

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 257mm

• Diameter: 70mm

• H.P.R.V. right of inlet

• 1 x switch port left of inlet

To suit Chrysler Valiant CL, CM

• Fitting: Inlet 3/8” No. 6 MIOR

RDX245

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 128mm

• Diameter: 63mm

To suit Citroen Berlingo

7/1996 >

• Height: 342mm

RDX247

• Diameter: 40mm

To suit Citroen C4, C5, C8

3/2001 >

• Fitting: Inlet 3/8” No. 6 MIOR

RDX929

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 162mm

• Diameter: 76mm

• 1 x charge port

To suit Citroen Xantia 2.0L

3/1996 >

• Fitting: Inlet 3/8” No. 6 MIOR

RDX928

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 162mm

• Diameter: 76mm

• 1 x charge port

To suit Citroen Xantia 2.0L

9/1994 - 3/1998

• Fitting: Inlet M27 x 1.5 FIOR

RDX455

• Fitting: Outlet M27 x 1.5 MIOR

• Height: 205mm

• Diameter: 90mm

• R134a charge port

To suit Daewoo 1.5i

9/1994 - 9/1995

• Fitting: Inlet M27 x 1.5 FIOR

RDX453

• Fitting: Outlet M27 x 1.5 MIOR

• Height: 205mm

• Diameter: 90mm

• R134a charge port

To suit Daewoo Cielo 1.5L 9/1995 - 6/1998

Espero 2.0L 3/1995 - 8/1997

Contents Index

404

Receiver Driers to suit DAEWOO to DAIHATSU

• Fitting: Inlet 3/4” No. 12 FIOR

RDX454

• Fitting: Outlet 3/4” No. 12 MIOR

• Height: 224mm

• Diameter: 93mm

• 1 x access port

• R12 System

To suit Daewoo Cielo 1.5L

Up to 1994

• Fitting: Inlet Pad

RDX451

• Fitting: Outlet Pad

• Height: 149mm

• Diameter: 60mm

To suit Daewoo Lanos

8/1997 - 4/2003

• Fitting: Inlet Pad

RDX7302

• Fitting: Outlet Pad

• Height: 150mm

• Diameter: 60mm

To suit Daewoo Leganza

4/1999 - 1/2005

• Fitting: Inlet Pad

RDX450

• Fitting: Outlet Pad

• Height: 149mm

• Diameter: 60mm

To suit Daewoo Leganza

8/1997 - 4/1999

• Fitting: Inlet Pad

RDX162

• Fitting: Outlet Pad

• Height: 120mm

• Diameter: 60mm

• 1 x switch ports

To suit Daewoo Matiz 0.8L 3 cyl

10/1999 - 1/2005

• Fitting: Inlet Pad

RDX7302

• Fitting: Outlet Pad

• Height: 150mm

• Diameter: 60mm

To suit Daewoo Nubira 1.6 & 2.0L

7/1997 - 12/2003

• Fitting: Inlet Pad

RDX452

• Fitting: Outlet Pad

• Height: 150mm

• Diameter: 60mm

To suit Daewoo Nubira

7/1997 - 10/1999, Leganza

• Fitting: Inlet Pad

RDX7302

• Fitting: Outlet Pad

• Height: 150mm

• Diameter: 60mm

To suit Daewoo Tacuma

10/2000 - 1/2005

• Length: 230mm

RDX0040To suit Daihatsu Applause

9/1997 - 5/2000

• Fitting: Inlet Pad

RDX284

• Fitting: Outlet Pad

• Height: 185mm

• Diameter: 60mm

To suit Daihatsu Applause

9/1993 - 9/1997

Contents Index 405

Receiver Driers to suit DAIHATSU

• Fitting: Inlet Pad

RDX282

• Fitting: Outlet Pad

• Height: 184mm

• Diameter: 60mm

To suit Daihatsu Applause

10/1989 - 2/1994

• Fitting: Inlet Pad

RDX281

• Fitting: Outlet Pad

• Height: 159mm

• Diameter: 60mm

To suit Daihatsu Charade G200, G202, G203

2/1992 >

• Fitting: Inlet Pad

RDX161

• Fitting: Outlet Pad

• Height: 150mm

• Diameter: 60mm

To suit Daihatsu Charade G100

10/1988 - 2/1991

• Fitting: Inlet Pad

RDX282

• Fitting: Outlet Pad

• Height: 184mm

• Diameter: 60mm

To suit Daihatsu Charade G100, G102

6/1987 - 1/1993

• Fitting: Inlet 5/16” No. 5 MIOR

RDX086

• Fitting: Outlet 5/16” No. 5 MIOR

• Height: 189mm

• Diameter: 67mm

• 1 x switch port

To suit Daihatsu Charade G10/G11 4/1980 - 6/1987

Handivan LV60 1/1982 - 3/1986, Rocky LV60 1/1982 - 8/1993

• Length: 230mm

RDX0040

• Length: 230mm

6/1999 - 4/2001

To suit Daihatsu Cuore L700S 1.0L 3 cyl

7/2000 - 10/2002

• Fitting: Inlet Pad

RDX284

• Fitting: Outlet Pad

• Height: 185mm

• Diameter: 60mm

To suit Daihatsu Delta

1/1994 - 11/1999

• Fitting: Inlet Pad

RDX284

• Fitting: Outlet Pad

• Height: 185mm

• Diameter: 60mm

To suit Daihatsu Feroza F300

7/1993 - 5/1998

• Fitting: Inlet Pad

RDX282

• Fitting: Outlet Pad

• Height: 184mm

• Diameter: 60mm

To suit Daihatsu Feroza

10/1988 - 11/1993

RDX0040To suit Daihatsu Handivan L701

Contents Index

406

Receiver Driers to suit DAIHATSU to DEUTZ

• Fitting: Inlet 5/16” No. 5 MIOR

RDX160

• Fitting: Outlet 5/16” No. 5 MIOR

• Height: 193mm

• Diameter: 67mm

• 2 x switch ports

• Sight glass

To suit Daihatsu Hi-Jet S75

3/1984 - 12/1986

• Fitting: Inlet Pad

RDX282

• Fitting: Outlet Pad

• Height: 184mm

• Diameter: 60mm

To suit Daihatsu Mira L200

4/1992 - 4/1995

• Fitting: Inlet Pad

RDX604

• Fitting: Outlet Pad

• Height: 165mm

• Diameter: 60mm

To suit Daihatsu Mira L500 2/1997 >

Move L601 2/1997 >

• Fitting: Inlet Pad

RDX281

• Fitting: Outlet Pad

• Height: 159mm

• Diameter: 60mm

To suit Daihatsu Pyzar G303

2/1997 - 8/2000

• Fitting: Inlet Pad

RDX284

• Fitting: Outlet Pad

• Height: 185mm

• Diameter: 60mm

To suit Daihatsu Rocky F78

8/1993 - 7/1998

RDX0040To suit Daihatsu Sirion

RDX0040To suit Daihatsu Terios

• Fitting: Inlet Pad

RDX281

• Fitting: Outlet Pad

• Height: 159mm

• Diameter: 60mm

To suit Daihatsu Terios

6/1997 - 11/2000

• Fitting: Inlet 3/8” No. 6 MIOR

RDX936

• Fitting: Outlet 3/8” No. 6 FOR

• Height: 175mm

• Diameter: 63mm

• 1 x Access port

• 1 x Sight glass

To suit Deutz Agroplus Tractor

2002 >

• Fitting: Inlet 3/8” No. 6 MIOR

RDX927

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 174mm

• Diameter: 74mm

To suit Deutz Tractor

• Length: 230mm

6/1998 - 2/2005

• Length: 230mm

5/1999 >

Top Bottom

Contents Index 407

Receiver Driers to suit EUNOS to FORD

• Fitting: Inlet Pad

RDX182

• Fitting: Outlet Pad

• Height: 160mm

• Diameter: 60mm

• 1 x switch port

• 1 x switch port

To suit Eunos 30X

2/1994 - 12/1997

• Fitting: Inlet Pad

RDX600

• Fitting: Outlet Pad

• Height: 161mm

• Diameter: 60mm

• 2 x switch ports

• R12 System

To suit Eunos 30X

10/1992 - 1/1994

• Fitting: Inlet Pad

RDX601

• Fitting: Outlet Pad

• Height: 163mm

• Diameter: 60mm

• 1 x switch port

To suit Eunos 500

9/1996 - 11/1999

• Fitting: Inlet 3/8” No. 6 MF

RDX006

• Fitting: Outlet 3/8” No. 6 MF

• Height: 184mm

• Diameter: 64mm

• 1 x switch port left of inlet

To suit Fieldstar Rooftop System

• Fitting: Inlet 5/8” No. 10 MIOR

RDX752

• Fitting: Outlet 5/8” No. 10 MIOR

• Height: 200mm

• Diameter: 90mm

• R134a service port

• Pressure switch PSX033

To suit Ford Aeromax

Ford L Series

• Fitting: Inlet Pad

RDX282

• Fitting: Outlet Pad

• Height: 184mm

• Diameter: 60mm

To suit Ford Capri SA - SC

10/1989 - 7/1993

• Fitting: Inlet 3/8” No. 6 MIOR

RDX029

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 186mm

• Diameter: 63mm

• 1 x switch port

• Pressure relief valve right

of inlet

To suit Ford Corsair UA

11/1989 - 12/1992

• Fitting: Inlet Pad

RDX191

• Fitting: Outlet Pad

• Height: 151mm

• Diameter: 60mm

• Includes pressure switch

(PSX081)

To suit Ford Courier PG

11/2002 - 8/2004

• Fitting: Inlet Pad

RDX608

• Fitting: Outlet Pad

• Height: 186mm

• Diameter: 60mm

• Switch Port 3/8” x 24UNF

To suit Ford Courier PE

2/1999 - 11/2002

• Fitting: Inlet 5/16” No. 5 MIOR

RDX022

• Fitting: Outlet 5/16” No. 5 MIOR

• Height: 200mm

• Diameter: 60mm

• 2 x switch ports

To suit Ford Courier PD

1996 - 1999

Contents Index

408

Receiver Driers to suit FORD

• Fitting: Inlet 5/16” No. 5 MIOR

RDX026

• Fitting: Outlet 5/16” No. 5 MIOR

• Height: 201mm

• Diameter: 63mm

• 2 x switch ports

To suit Ford Courier PC

1989 - 1996

• Fitting: Inlet 5/18” No. 10 MIOR

RDX183

• Fitting: Outlet MSL

• Height: 210mm

• Diameter: 89mm

• 1 x access port

To suit Ford Escape 2.3 & 3.0L

3/2001 - 4/2008

• Fitting: Inlet 5/8” No. 10 MIOR • Length: 230mm

2/2008 >

RDX755

• Fitting: Outlet FSL

• Height: 205mm

• Diameter: 85mm

• R134a charge port

• M12 Switch Port

To suit Ford Explorer UN - UT 4.0L V6

11/1996 - 2/2003

RDX0360To suit Ford Falcon FG 6 and 8 cyl

• Fitting: Inlet FSL

RDX759

• Fitting: Outlet Female Pad

• Height: 205mm

• Diameter: 89mm

To suit Ford Falcon BA 6 cyl & V8 9/2002 - 10/2005

Falcon BF Series I & II 6 cyl & V8 9/2005 - 4/2008

• Fitting: Inlet FSL

RDX093

• Fitting: Outlet Female Pad

• Height: 210mm

• Diameter: 90mm

To suit Ford Falcon AU 6 cyl & V8

9/1998 - 10/2002

• Fitting: Inlet 3/8” No. 6 MIOR

RDX084

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 256mm

• Diameter: 70mm

• 3/16” service port

• Includes mounting studs

To suit Ford Falcon EA, EB & EB II

2/1988 - 8/1993

• Fitting: Inlet 3/8” No. 6 MIOR

RDX085

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 201mm

• Diameter: 64mm

• Includes mounting studs

To suit Ford Falcon ED, EF & EL

8/1993 - 9/1998

• Fitting: Inlet 3/8” No. 6 FOR

RDX083

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 310mm

• Diameter: 64mm

To suit Ford Falcon XF & XG

10/1984 - 1/1996

• Fitting: Inlet 3/8” No. 6 MIOR

1/1983 - 10/1984

RDX082

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 258mm

• Diameter: 70mm

• 1 x access port

• 1 x switch port

To suit Ford Falcon XE

Contents Index 409

Receiver Driers to suit FORD

• Fitting: Inlet 3/8” No. 6 MIOR

RDX081

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 255mm

• Diameter: 70mm

To suit Ford Falcon XD & XE

4/1981 - 10/1983

• Fitting: Inlet 3/8” No. 6 MIOR

RDX080

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 260mm

• Diameter: 70mm

To suit Ford Falcon XD

3/1979 - 3/1982

• Fitting: Inlet 3/8” No. 6 MIOR

RDX090

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 255mm

• Diameter: 70mm

• 1 x male switch port

To suit Ford Falcon XC

8/1976 - 10/1979

• Fitting: Inlet Pad

RDX283

• Fitting: Outlet Pad

• Height: 158mm

• Diameter: 60mm

To suit Ford Festiva WF

1/1998 - 12/2000

• Fitting: Inlet Pad

RDX601

• Fitting: Outlet Pad

• Height: 163mm

• Diameter: 60mm

• 1 x switch port

To suit Ford Festiva WF

1/1998 - 12/2000

• Fitting: Inlet Pad

RDX601

• Fitting: Outlet Pad

• Height: 163mm

• Diameter: 60mm

• 1 x switch port

To suit Ford Festiva WB Series I & II

3/1994 - 12/1997

• Fitting: Inlet Pad

RDX094

• Fitting: Outlet Pad

• Height: 165mm

• Diameter: 60mm

• Switch Port: M11 x 1.0

• Pressure switch

to suit PSX038

To suit Ford Festiva WB, WD, WF

4/1994 - 12/1996

RDX022To suit Ford Festiva WB, WD, WF

• Fitting: Inlet 5/16” No. 5 MIOR

• Fitting: Outlet 5/16” No. 5 MIOR

• Height: 200mm

• Diameter: 60mm

• 2 x switch ports

Air International system

2/1995 - 12/1996

• Fitting: Inlet Pad

RDX600

• Fitting: Outlet Pad

• Height: 161mm

• Diameter: 60mm

• 2 x switch ports

To suit Ford Festiva WA

10/1991 - 3/1994

• Fitting: Inlet 3/4” No. 12 FSL

RDX188

• Fitting: Outlet 3/4” No. 12 MSL

• Height: 250mm

• Diameter: 90mm

• 1 x pressure switch

• 1 x access port

To suit Ford Fiesta

2/2004 - 1/2006

Contents Index

410

Receiver Driers to suit FORD

• Fitting: Inlet Pad

RDX185

• Fitting: Outlet FSL

• Height: 200mm

• Diameter: 89mm

• 1 x Service port

To suit Ford Focus LR

9/2002 - 6/2005

• Fitting: Inlet Pad

RDX612

• Fitting: Outlet Pad

• Height: 147mm

• Diameter: 60mm

• 1 x switch port

To suit Ford Laser KJ Series II & III 12/1996 - 2/1999

Laser KL 12/1996 >

• Fitting: Inlet Pad

RDX087

• Fitting: Outlet Pad

• Height: 162mm

• Diameter: 60mm

• 2 x switch ports

To suit Ford Laser KJ Series I & II

10/1994 - 2/1999

• Fitting: Inlet Pad

RDX182

• Fitting: Outlet Pad

• Height: 160mm

• Diameter: 60mm

• 1 x switch port

• 1 x switch port

To suit Ford Laser KJ 10/1994 - 12/1996

Laser KN 2/1999 - 4/2001

• Fitting: Inlet Pad

RDX181

• Fitting: Outlet Pad

• Height: 165mm

• Diameter: 61mm

• 2 x switch ports

To suit Ford Laser KH 11/1993 - 10/1994

Telstar AV 1/1990 - 1/1992

• Fitting: Inlet Pad

RDX180

• Fitting: Outlet Pad

• Height: 164mm

• Diameter: 61mm

• 2 x switch ports

To suit Ford Laser KF - KH

1/1990 - 7/1993

• Fitting: Inlet 5/16” No. 5 MIOR

RDX086

• Fitting: Outlet 5/16” No. 5 MIOR

• Height: 189mm

• Diameter: 67mm

• 2 x switch ports

To suit Ford Laser KA - KB 3/1981 - 10/1985

Meteor GA - GC 4/1982 - 9/1987, Telstar AR - AS 5/1983 - 10/1987

• Fitting: Inlet 3/8” No. 6 MIOR

RDX402

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 257mm

• Diameter: 70mm

• H.P.R.V. right of inlet

• 1 x switch port left of inlet

To suit Ford Louisville

• Fitting: Inlet M20 x 1.5 MIOR

RDX221

• Fitting: Outlet M16 x 1.5 MIOR

• Height: 278mm

• Diameter: 60mm

• 2 x switch ports

• With Diesel Kiki compressor

To suit Ford Maverick

2/1988 - 2/1994

• Fitting: Inlet 3/8” No. 6 MIOR

RDX027

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 200mm

• Diameter: 63mm

• 2 x switch ports

To suit Ford Maverick DA

2/1988 - 2/1994

Contents Index 411

Receiver Driers to suit FORD

• Fitting: Inlet 5/16” No. 5 MIOR

RDX022

• Fitting: Outlet 5/16” No. 5 MIOR

• Height: 200mm

• Diameter: 60mm

• 2 x switch ports

To suit Ford Meteor KA - KE

3/1981 - 10/1994

• Fitting: Inlet 5/8” No. 10 FSL

RDX756

• Fitting: Outlet 5/8” No. 10 FSL

• Height: 311mm

• Diameter: 89mm

• M12 x 1.5 switch port

To suit Ford Mondeo HB - HD 2.0L

7/1995 - 2/2000

• Fitting: Inlet 5/8” No. 10 FSL

RDX091

• Fitting: Outlet 5/8” No. 10 FSL

• Height: 312mm

• Diameter: 89mm

• M12 x 1.5 access port

To suit Ford Mondeo HB

7/1995 - 8/1996

• Fitting: Inlet MSL

RDX760

• Fitting: Outlet FSL

• Height: 202mm

• Diameter: 89mm

To suit Ford Mondeo 1.8TD, 2.5 V6

9/1993 - 4/2001

• Fitting: Inlet 3/8” No. 6 MIOR

RDX516

• Fitting: Outlet 3/8” No. 6 FIOR

• Height: 155mm

• Diameter: 64mm

To suit Ford New Holland Tractor

• Fitting: Inlet 5/8” No. 10 MIOR

RDX752

• Fitting: Outlet 5/8” No. 10 MIOR

• Height: 200mm

• Diameter: 90mm

• R134a service port

• Pressure switch PSX033

To suit Ford Sterling

• Fitting: Inlet 5/8” No. 10 FSL

RDX753

• Fitting: Outlet 3/4” No. 10 MSL

• Height: 200mm

• Diameter: 85mm

• M12 x 1.5 switch port

To suit Ford Taurus DN 3.0L V6

3/1996 - 12/1998

• Fitting: Inlet Pad

RDX182

• Fitting: Outlet Pad

• Height: 160mm

• Diameter: 60mm

• 1 x switch port

To suit Ford Telstar AX

5/1993 - 8/1994

• Fitting: Inlet Pad

RDX087

• Fitting: Outlet Pad

• Height: 162mm

• Diameter: 60mm

• 2 x switch ports

To suit Ford Telstar AX 12/1992 - 7/1996

Telstar TX5 V6 1/1992 - 8/1994

• Fitting: Inlet M16 x 1.5 MIOR

RDX089

• Fitting: Outlet M16 x 1.5 MIOR

• Height: 204mm

• Diameter: 60mm

• 2 x switch ports

• Metric

To suit Ford Telstar AT - AV

10/1987 - 7/1996

Contents Index

412

Receiver Driers to suit FORD

• Fitting: Inlet FSL

RDX759

• Fitting: Outlet Female Pad

• Height: 205mm

• Diameter: 89mm

To suit Ford Territory SX, SY Series I & II

4/2004 >

• Fitting: Inlet 3/8” No. 6 MIOR

RDX405

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 156mm

• Diameter: 76mm

• 1 x access port left of inlet

To suit Ford Tractor

• Fitting: Inlet 3/8” No. 6 MF

RDX512

• Fitting: Outlet 3/8” No. 6 MF

• Height: 156mm

• Diameter: 76mm

To suit Ford Tractor

• Fitting: Inlet 3/8” No. 6 MIOR

RDX523

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 166mm

• Diameter: 101mm

To suit Ford Tractor

• Fitting: Inlet 3/8” No. 6 FSL

RDX099

• Fitting: Outlet 3/8” No. 6 FSL

• Height: 360mm

• Diameter: 75mm

To suit Ford Tractor

• Fitting: Inlet 3/8” No. 6 MIOR

RDX080

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 260mm

• Diameter: 70mm

To suit Ford Tractor & Truck

• Fitting: Inlet 3/8” No. 6 MF

RDX031

• Fitting: Outlet 3/8” No. 6 MF

• Height: 167mm

• Diameter: 76mm

• 1 x switch port left of inlet

To suit Ford Tractor 7710

• Fitting: Inlet 3/8” No. 6 MIOR

RDX754

• Fitting: Outlet 3/8” No. 6 FIOR

• Height: 233mm

• Diameter: 76mm

To suit Ford Tractor TS100

• Fitting: Inlet 7/8” QD

RDX095

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 185mm

• Diameter: 101mm

To suit Ford Tractor TW20 - 25

• Fitting: Inlet Pad

RDX751

• Fitting: Outlet Pad

• Height: 260mm

• Diameter: 90mm

• Pressure switch - PSX051

To suit Ford Transit VI

7/1999 - 12/2000

Contents Index 413

Receiver Driers to suit FORD to HITACHI

• Fitting: Inlet FSL

RDX750

• Fitting: Outlet FSL

• Height: 225mm

• Diameter: 90mm

• Pressure Switch: PSX033

To suit Ford Transit VF 2.0 Petrol, 2.5TD 4/1996 - 1/1997

Transit VG 2.0L Petrol, 2.3 & 2.5L TD 1/1997 - 12/2000

• Fitting: Inlet 3/8” No. 6 MIOR

RDX533

• Fitting: Outlet 3/8” No. 6 FIOR

• Height: 255mm

• Diameter: 76mm

• 2 x M10 x 1.25 service ports

To suit Freightliner FLD112, FLD120

1994 - 1999

• Fitting: Inlet 3/8” No. 6 MIOR

RDX517

• Fitting: Outlet 3/8” No. 6 FIOR

• Height: 238mm

• Diameter: 76mm

• Moisture indicator

• 2 x access ports

To suit Freightliner FL112

• Fitting: Inlet 3/8” No. 6 MIOR

RDX530

• Fitting: Outlet 3/8” No. 6 FIOR

• Height: 255mm

• Diameter: 80mm

• 2 x M10 x 1.25 service ports

To suit Freightliner FL80

• Fitting: Inlet Quick Connect

1994 - 1999

RDX536

• Fitting: Outlet Quick Connect

• Height: 250mm

• Diameter: 76mm

• 2 x M10 x 1.25 service ports

To suit Freightliner FLD112, FLD120

• Fitting: Inlet 3/8” No. 6 MF

RDX031

• Fitting: Outlet 3/8” No. 6 MF

• Height: 167mm

• Diameter: 76mm

• 1 x switch port left of inlet

To suit Gason Tractor Cabs

• Fitting: Inlet 5/16” No. 5 MIOR

RDX289

• Fitting: Outlet 5/16” No. 5 MIOR

• Height: 275mm

• Diameter: 67mm

• 2 x switch ports

• Sight glass

To suit Hino Truck

• Fitting: Inlet 3/8” No. 6 MIOR

RDX290

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 275mm

• Diameter: 67mm

• 2 x switch ports

• Sight glass

To suit Hino Truck

• Fitting: Inlet Pad

RDX529

• Fitting: Outlet Pad

• Height: 255mm

• Diameter: 60mm

To suit Hino Truck

• Fitting: Inlet Pad

RDX065

• Fitting: Outlet Pad

• Height: 229mm

• Diameter: 75mm

• Pressure Switch PSX043

(not included)

To suit Hitachi Excavators EX1800, EX2500,

EX2800 & EX3600

Contents Index

414

Receiver Driers to suit HITACHI to HOLDEN

• Fitting: Inlet Pad

RDX072

• Fitting: Outlet Pad

• Height: 215mm

• Diameter: 61mm

• Pilot Hole: 9.0mm

• Sight glass

• 2 x switch ports

To suit Hitachi EX120, EX150, EX200, EX300

• Fitting: Inlet 3/8” No. 6 FIOR

RDX522

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 228mm

• Diameter: 102mm

• Sight glass

• Moisture indicator

To suit Hitachi

1991 - 1993

• Fitting: Inlet Pad

RDX529

• Fitting: Outlet Pad

• Height: 255mm

• Diameter: 60mm

To suit Hitachi

• Fitting: Inlet Pad

RDX281

• Fitting: Outlet Pad

• Height: 159mm

• Diameter: 60mm

To suit Holden Apollo JM, JP

4/1993 - 5/1997

• Fitting: Inlet Pad

RDX284

• Fitting: Outlet Pad

• Height: 185mm

• Diameter: 60mm

• R134a system

To suit Holden Apollo 8/1991 - 2/1993

Nova LF 9/1991 - 10/1994

• Fitting: Inlet Pad

RDX161

• Fitting: Outlet Pad

• Height: 150mm

• Diameter: 60mm

To suit Holden Apollo JK, JL

8/1989 - 2/1993

• Fitting: Inlet Pad

RDX283

• Fitting: Outlet Pad

• Height: 158mm

• Diameter: 60mm

• R12 System

To suit Holden Apollo 8/1989 - 2/1993

Barina MF, MH 2/1989 - 5/1994, Nova 8/1989 - 10/1994 10/2001 - 12/2006

RDX119To suit Holden Astra TS Series II

• Length: 380mm

Desiccant Cartridge

• Fitting: Inlet Pad

RDX114

• Fitting: Outlet Pad

• Height: 111mm

• Diameter: 60mm

• Switch port

• Pressure Switch PSX046

(not included)

To suit Holden Astra TS

• Fitting: Inlet M18 x 1.5 MIOR

RDX107

• Fitting: Outlet Pad

• Height: 183mm

• Diameter: 76mm

To suit Holden Astra TR

8/1996 - 9/19983/1998 - 12/2001

Top

Bottom

Contents Index 415

Receiver Driers to suit HOLDEN

• Fitting: Inlet 3/8” No. 6 MIOR

RDX025

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 203mm

• Diameter: 60mm

• 2 x switch ports

To suit Holden Astra LD

7/1987 - 7/1989

• Fitting: Inlet 3/8” No. 6 MIOR

RDX029

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 186mm

• Diameter: 63mm

• H.P.R.V. right of inlet

• 1 x switch port

To suit Holden Astra LB, LC

8/1984 - 6/1987

• Fitting: Inlet 3/8” No. 6 MIOR

RDX030

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 182mm

• Diameter: 63mm

• 1 x switch port

• 1 x access port right of inlet

To suit Holden Astra

8/1984 - 12/1989

• Fitting: Inlet 3/8” No. 6 MIOR

RDX033

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 182mm

• Diameter: 63mm

• H.P.R.V. left of inlet

• 1 x switch port

To suit Holden Astra

7/1987 >

• Fitting: Inlet Pad

RDX134

• Fitting: Outlet Pad

• Height: 168mm

• Diameter: 55mm

To suit Holden Barina XC

1/2004 >

• Fitting: Inlet Pad

RDX110

• Fitting: Outlet Pad

• Height: 170mm

• Diameter: 55mm

To suit Holden Barina XC Combo

2001 - 2003

• Fitting: Inlet Pad

RDX108

• Fitting: Outlet Pad

• Height: 202mm

• Diameter: 63mm

To suit Holden Barina SB imported 4/1994 - 12/2000

Calibra YE 10/1997 - 11/1997

• Fitting: Inlet 5/16” No. 5 MIOR

RDX086

• Fitting: Outlet 5/16” No. 5 MIOR

• Height: 189mm

• Diameter: 67mm

To suit Holden Barina SB 4/1994 - 12/2000

Nova LE 8/1989 - 8/1991

• Fitting: Inlet Pad

RDX116

• Fitting: Outlet Pad

• Height: 168mm

• Diameter: 60mm

• 2 x switch ports

• Sight glass

To suit Holden Barina SB

4/1994 - 12/2000

• Fitting: Inlet Pad

RDX223

• Fitting: Outlet Pad

• Height: 165mm

• Diameter: 60mm

To suit Holden Barina MF - MH

1/1989 - 4/1994

Contents Index

416

Receiver Driers to suit HOLDEN

• Fitting: Inlet 5/16” No. 5 MIOR

RDX160

• Fitting: Outlet 5/16” No. 5 MIOR

• Height: 193mm

• Diameter: 67mm

• 2 x male switch ports

• Sight glass

To suit Holden Barina

1/1989 - 9/1991

• Fitting: Inlet 5/16” No. 5 MIOR

RDX040

• Fitting: Outlet 5/16” No. 5 MIOR

• Height: 203mm

• Diameter: 60mm

• 2 x male switch ports

To suit Holden Barina ML

9/1986 - 2/1989

• Fitting: Inlet 3/8” No. 6 MIOR

RDX030

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 182mm

• Diameter: 63mm

• 1 x switch port

• 1 x access port right of inlet

To suit Holden Camira JB - JE

8/1982 - 7/1989

• Fitting: Inlet Pad

RDX118

• Fitting: Outlet Pad

• Height: 163mm

• Diameter: 60mm

• 2 x switch ports

To suit Holden Colorado

2008 >

RDX113To suit Holden Commodore VE

7/2006 >

Desiccant Cartridge • Fitting: Inlet 5/16” No. 5 with No. 6 pilot

• Length: 325mm

RDX117

• Fitting: Outlet 5/16” No. 5 with No. 6 pilot

• Height: 195mm

• Diameter: 60mm

To suit Holden Commodore VY

9/2002 - 8/2004

• Fitting: Inlet 5/16” No. 5 with No. 6 pilot

RDX106

• Fitting: Outlet 5/16” No. 5 with No. 6 pilot

• Height: 204mm

• Diameter: 60mm

To suit Holden Commodore VT - VZ

10/1997 - 1/2006

RDX923To suit Holden Commodore VT Series III, VX & VY

Condenser/Drier Bracket

• Fitting: Inlet 5/16” No. 5 MIOR

RDX101

• Fitting: Outlet 5/16” No. 5 MIOR

• Height: 203mm

• Diameter: 60mm

• 1 x switch port

To suit Holden Commodore VR, VS

7/1993 - 8/1997

• Fitting: Inlet 3/4” No. 12 FIOR

RDX104

• Fitting: Outlet 3/4” No. 12 MIOR

• Height: 228mm

• Diameter: 89mm

• 2 x access ports

To suit Holden Commodore VN, VP

8/1988 - 9/1991

Contents Index 417

Receiver Driers to suit HOLDEN

• Fitting: Inlet 3/8” No. 6 MIOR

RDX100

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 203mm

• Diameter: 60mm

• 1 x switch port

To suit Holden Commodore VL 6 cyl

3/1986 - 8/1988

• Fitting: Inlet 3/8” No. 6 MIOR

RDX030

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 182mm

• Diameter: 63mm

• 1 x switch port

• 1 x access port right of inlet

To suit Holden Commodore VC - VH 6 cyl 6/1980 - 3/1982

Commodore VK - VL 8 cyl 9/1984 - 3/1986

• Fitting: Inlet 3/8” No. 6 MIOR

RDX033

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 182mm

• Diameter: 63mm

• H.P.R.V. left of inlet

• 1 x switch port

To suit Holden Commodore VB - VL 6 & 8 cyl

11/1978 >

• Fitting: Inlet 3/8” No. 6 MIOR

RDX025

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 203mm

• Diameter: 60mm

• 2 x switch ports

To suit Holden Commodore VB - VK

11/1978 - 3/1986

• Fitting: Inlet Pad

RDX115

• Fitting: Outlet Pad

• Height: 215mm

• Diameter: 32mm

To suit Holden Cruze 1.5L 4 cyl

7/2002 - 6/2006

• Fitting: Inlet Pad

RDX610

• Fitting: Outlet Pad

• Height: 151mm

• Diameter: 60mm

To suit Holden Frontera

1999 >

• Fitting: Inlet 3/8” No. 6 BARB

RDX105

• Fitting: Outlet 3/8” No. 6 FIOR

• Height: 176mm

• Diameter: 70mm

To suit Holden Kingswood HJ - HZ 6 & 8 cyl 10/1974 - 5/1980

Statesman HQ - HZ 7/1971 - 5/1980

• Fitting: Inlet Pad

RDX608

• Fitting: Outlet Pad

• Height: 186mm

• Diameter: 60mm

• Switch Port 3/8” x 24UNF

To suit Holden Jackaroo

9/1999 - 4/2004

• Fitting: Inlet Pad

RDX604

• Fitting: Outlet Pad

• Height: 165mm

• Diameter: 60mm

To suit Holden Jackaroo 3.1L

11/1997 - 1999

• Fitting: Inlet 5/16” No. 5 with No. 6 pilot

RDX117

• Fitting: Outlet 5/16” No. 5 with No. 6 pilot

• Height: 195mm

• Diameter: 60mm

To suit Holden Monaro 6 & 8 cyl

2003 >

Contents Index

418

Receiver Driers to suit HOLDEN

• Fitting: Inlet 5/16” No. 5 with No. 6 pilot

RDX106

• Fitting: Outlet 5/16” No. 5 with No. 6 pilot

• Height: 204mm

• Diameter: 60mm

To suit Holden Monaro 6 & 8 cyl

2001 - 2003

• Fitting: Inlet Pad

RDX604

• Fitting: Outlet Pad

• Height: 165mm

• Diameter: 60mm

To suit Holden Nova LG

10/1994 - 9/1996

• Fitting: Inlet Pad

1992 - 1994

RDX284

• Fitting: Outlet Pad

• Height: 185mm

• Diameter: 60mm

• R134a system

To suit Holden Nova LE - LF

• Fitting: Inlet Pad

8/1989 - 8/1991

RDX282

• Fitting: Outlet Pad

• Height: 184mm

• Diameter: 68mm

To suit Holden Nova LE

• R12

• Fitting: Inlet Pad

RDX118

• Fitting: Outlet Pad

• Height: 163mm

• Diameter: 60mm

• 2 x switch ports

To suit Holden Rodeo RA03

3/2003 >

RDX022To suit Holden Rodeo R7 & R9

• Fitting: Inlet 5/16” No. 5 MIOR

• Fitting: Outlet 5/16” No. 5 MIOR

• Height: 200mm

• Diameter: 60mm

• 2 x switch ports

2/1999 - 2/2003

Air International system

• Fitting: Inlet 5/16” No. 5 with No. 6 pilot

RDX106

• Fitting: Outlet 5/16” No. 5 with No. 6 pilot

• Height: 204mm

• Diameter: 60mm

To suit Holden Statesman WH 3.8L V6 & 5.7L V8

6/1999 - 4/2003

• Fitting: Inlet Pad

RDX163

• Fitting: Outlet Pad

• Height: 155mm

• Diameter: 60mm

To suit Holden Vectra ZC

3/2003 >

• Fitting: Inlet Pad

RDX109

• Fitting: Outlet Pad

• Height: 175mm

• Diameter: 70mm

To suit Holden Vectra JR, JS

6/1997 - 11/2000

• Fitting: Inlet Pad

RDX114

• Fitting: Outlet Pad

• Height: 111mm

• Diameter: 60mm

• Pressure Switch PSX046

(not included)

To suit Holden Zafira TT

6/2001 - 12/2003

Top

Bottom

Contents Index 419

Receiver Driers to suit HOLDEN to HONDA

RDX0050

• Length: 225mm

To suit Honda Accord

8/2003 - 6/2006

• Fitting: Inlet Pad

RDX282

• Fitting: Outlet Pad

• Height: 184mm

• Diameter: 60mm

To suit Honda Accord

10/1990 - 10/1993

• Fitting: Inlet Pad

RDX281

• Fitting: Outlet Pad

• Height: 159mm

• Diameter: 60mm

To suit Honda Accord

11/1993 - 12/1997

IN

• Fitting: Inlet M16 x 1.5 MIOR

RDX126

• Fitting: Outlet M16 x 1.5 MIOR

• Height: 185mm

• Diameter: 61mm

To suit Honda Accord 2.0, 2.6, 2.8L

• Fitting: Inlet Pad

RDX653

• Fitting: Outlet Pad

• Height: 161mm

• Diameter: 60mm

• 1 x male switch port

To suit Honda City 1.5L

2/2009 >

• Fitting: Inlet Pad

RDX653

• Fitting: Outlet Pad

• Height: 161mm

• Diameter: 60mm

• 1 x male switch port

To suit Honda Civic 1.6L

3/1999 - 10/2000

• Fitting: Inlet Pad

RDX602

• Fitting: Outlet Pad

• Height: 164mm

• Diameter: 60mm

• R134a system

To suit Honda Civic 10/1993 - 10/1995

CRX 8/1994 - 6/1998

• Fitting: Inlet Pad

RDX123

• Fitting: Outlet Pad

• Height: 163mm

• Diameter: 61mm

• R12 System

To suit Honda Civic

10/1991 - 10/1993

• Fitting: Inlet 3/8” No. 6 MIOR

RDX414

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 200mm

• Diameter: 70mm

• 2 x switch ports

To suit Honda Civic 5/1988 - 10/1993, Prelude 1979 - 1982,

Prelude 5/1979 - 1/1983, 4WS 1988 >

• Fitting: Inlet Pad

RDX654

• Fitting: Outlet Pad

• Height: 168mm

• Diameter: 61mm

To suit Honda Civic 5/1988 - 10/1993

Concerto 1.6L 11/1988 - 1/1993

Contents Index

420

Receiver Driers to suit HONDA

• Fitting: Inlet 3/8” No. 6 MIOR

RDX025

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 203mm

• Diameter: 60mm

• 2 x switch ports

To suit Honda Civic 2/1985 - 3/1989

Concerto some 11/1988 - 1/1993

RDX0040

• Length: 230mm

To suit Honda CRV

2002 - 2004

• Fitting: Inlet Pad

RDX653

• Fitting: Outlet Pad

• Height: 161mm

• Diameter: 60mm

• 1 x male switch port

To suit Honda CRV RD1 2.0L

10/1997 - 12/2001

• Fitting: Inlet Pad

RDX653

• Fitting: Outlet Pad

• Height: 161mm

• Diameter: 60mm

• 1 x male switch port

To suit Honda Integra

11/2001 >

• Fitting: Inlet Pad

RDX602

• Fitting: Outlet Pad

• Height: 164mm

• Diameter: 60mm

To suit Honda Integra

7/1993 - 10/1999

• Fitting: Inlet Pad

RDX123

• Fitting: Outlet Pad

• Height: 163mm

• Diameter: 61mm

• R12 System

To suit Honda Integra

6/1989 - 7/1993

RDX0050

•Length: 225mm

To suit Honda Jazz

2004 >

• Fitting: Inlet Pad

RDX283

• Fitting: Outlet Pad

• Height: 158mm

• Diameter: 60mm

To suit Honda Legend V6

11/1987 - 3/1991

• Fitting: Inlet 5/16” No. 5 MIOR

RDX040

• Fitting: Outlet 5/16” No. 5 MIOR

• Height: 203mm

• Diameter: 63mm

• 2 x switch ports

To suit Honda Legend V6

RDX0050

• Length: 225mm

To suit Honda Odyssey

6/2004 - 4/2009

Contents Index 421

Receiver Driers to suit HONDA to HYUNDAI

• Fitting: Inlet Pad

RDX284

• Fitting: Outlet Pad

• Height: 185mm

• Diameter: 60mm

• R134a system

To suit Honda Odyssey

6/1995 - 3/2000

• Fitting: Inlet Pad

RDX287

• Fitting: Outlet Pad

• Height: 245mm

• Diameter: 60mm

To suit Honda Odyssey 4 cyl

11/1999 >

IN

• Fitting: Inlet M16 x 1.5 MIOR

RDX126

• Fitting: Outlet M16 x 1.5 MIOR

• Height: 185mm

• Diameter: 61mm

To suit Honda Odyssey 2.0, 2.6, 2.8L

• Fitting: Inlet 5/16” No. 5 MIOR

RDX022

• Fitting: Outlet 5/16” No. 5 MIOR

• Height: 200mm

• Diameter: 60mm

• 2 x switch ports

To suit Honda Prelude

1993 >

• Fitting: Inlet 3/8” No. 6 MIOR

RDX414

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 200mm

• Diameter: 70mm

• 2 x switch ports

To suit Honda Prelude

5/1979 - 1/1983, 4WS 1988 >

• Fitting: Inlet 3/8” No. 6 MIOR

RDX406

• Fitting: Outlet 3/8” No. 6 FIOR

• Height: 160mm

• Diameter: 101mm

To suit Hupp-Aire VT524 Rooftop Unit

• Fitting: Inlet Pad

RDX491

• Fitting: Outlet Pad

• Height: 250mm

• Diameter: 40mm

To suit Hyundai Accent LC

5/2000 >

RDX0050

• Length: 225mm

To suit Hyundai Accent

9/1999 >

RDX0050

• Length: 225mm

To suit Hyundai Elantra

10/2000 >

• Fitting: Inlet Pad

RDX476

• Fitting: Outlet Pad

• Height: 146mm

• Diameter: 60mm

• Sight glass

• 2 x switch ports

To suit Hyundai Excel X3 1.5L 1/1994 - 12/2000

Lantra J2 & J3 1.8 & 2.0L 9/1995 - 10/2000

Contents Index

422

Receiver Driers to suit HYUNDAI

• Fitting: Inlet Pad

RDX477

• Fitting: Outlet Pad

• Height: 148mm

• Diameter: 60mm

• 1 x switch port

To suit Hyundai Excel X3 1.5L

1/1994 - 12/2000

• Fitting: Inlet Pad

RDX482

• Fitting: Outlet M22 x 1.5 MIOR

• Height: 210mm

• Diameter: 89mm

• 1 x Access port

• M12 switch ports

To suit Hyundai Excel X2

1989 - 1994

• Fitting: Inlet 3/8” No. 6 MIOR

RDX414

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 200mm

• Diameter: 70mm

• 2 x switch ports

To suit Hyundai Excel

5/1987 - 12/1989

RDX0040

• Length: 230mm

To suit Hyundai Getz TB

2002 >

• Fitting: Inlet M20 x 1.5 MIOR

RDX492

• Fitting: Outlet M16 x 1.5 MIOR

• Height: 195mm

• Diameter: 60mm

To suit Hyundai Grandeur XG

9/1999 - 4/2003

RDX0050

• Length: 225mm

To suit Hyundai Lantra XD

10/2000 - 9/2003

• Fitting: Inlet 3/8” No. 6 COR

RDX7510

• Fitting: Outlet 3/8” No. 6 COR

• Height: 203mm

• Diameter: 63mm

To suit Hyundai Lantra 1.8L 4 cyl

10/1992 - 8/1995

• Fitting: Inlet 5/16” No. 5 MIOR

RDX022

• Fitting: Outlet 5/16” No. 5 MIOR

• Height: 200mm

• Diameter: 60mm

• 2 x switch ports

To suit Hyundai Lantra

1991 - 1994

• Fitting: Inlet Pad

RDX491

• Fitting: Outlet Pad

• Height: 250mm

• Diameter: 40mm

To suit Hyundai Lavita

10/2001 >

• Fitting: Inlet Pad

RDX491

• Fitting: Outlet Pad

• Height: 250mm

• Diameter: 40mm

To suit Hyundai Santa Fe

11/2000 - 7/2008

Top Bottom

Contents Index 423

Receiver Driers to suit HYUNDAI to INTERNATIONAL

• Fitting: Inlet M20 x 1.5 MIOR

RDX492

• Fitting: Outlet M16 x 1.5 MIOR

• Height: 195mm

• Diameter: 60mm

To suit Hyundai Sonata EF

8/1998 - 9/2001

• Fitting: Inlet Pad

RDX475

• Fitting: Outlet Pad

• Height: 275mm

• Diameter: 89mm

• M12 x 1.5 access port

• Pressure switch To suit: PSX033

• R134a system

To suit Hyundai Sonata 2.0L DOHC

11/1993 - 8/1998

• Fitting: Inlet Pad

RDX491

• Fitting: Outlet Pad

• Height: 250mm

• Diameter: 40mm

To suit Hyundai Trajet 2.7L

7/2000 - 6/2008

• Fitting: Inlet Pad

RDX491

• Fitting: Outlet Pad

• Height: 250mm

• Diameter: 40mm

To suit Hyundai Tucson SA 2.7L

2005 >

• Fitting: Inlet 3/8” No. 6 MIOR

RDX132

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 236mm

• Diameter: 76mm

• Switch port right of inlet

• Sight glass right of inlet

• Moisture indicator left of inlet

To suit International S/T Line

• Fitting: Inlet 7/16” No. 7 FIOR

RDX130

• Fitting: Outlet 3/8” No. 6 FIOR

• Height: 255mm

• Diameter: 76mm

• 1 x switch port left of inlet

To suit International Trucks

• Fitting: Inlet 7/16” No. 7 FIOR

RDX131

• Fitting: Outlet 3/8” No. 6 FIOR

• Height: 257mm

• Diameter: 76mm

• Charge port

To suit International Trucks

• Fitting: Inlet 3/8” No. 6 MIOR

RDX404

• Fitting: Outlet 3/8” No. 6 FIOR

• Height: 198mm

• Diameter: 100mm

To suit International Trucks

• Fitting: Inlet 3/8” No. 6 MF

RDX403

• Fitting: Outlet 3/8” No. 6 MF

• Height: 161mm

• Diameter: 101mm

To suit International Trucks, Harvester

• Fitting: Inlet 3/8” No. 6 MIOR

RDX406

• Fitting: Outlet 3/8” No. 6 FIOR

• Height: 160mm

• Diameter: 101mm

To suit International Trucks, Harvester

Top Bottom

Contents Index

424

Receiver Driers to suit ISUZU to JAGUAR

• Fitting: Inlet Pad

RDX5810

• Fitting: Outlet Pad

• Height: 160mm

• Diameter: 60mm

• Switch Port: M11 x 1.0

To suit Isuzu Truck

• Fitting: Inlet M16 x 1.5 MIOR

RDX135

• Fitting: Outlet M16 x 1.5 MIOR

• Height: 235mm

• Diameter: 76mm

To suit Iveco Truck

• Fitting: Inlet M16 x 1.5 MIOR

RDX143

• Fitting: Outlet M16 x 1.5 MIOR

• Height: 525mm

• Diameter: 45mm

To suit Jaguar Daimler, Sovereign 1993 - 1997

Jaguar XJS 1993 - 1997

• Fitting: Inlet 3/8” No. 6 MF

RDX031

• Fitting: Outlet 3/8” No. 6 MF

• Height: 167mm

• Diameter: 76mm

• 1 x switch port left of inlet

To suit Jaguar Early

• Fitting: Inlet Pad

RDX144

• Fitting: Outlet Pad

• Height: 165mm

• Diameter: 65mm

• Access port

To suit Jaguar S type

• Fitting: Inlet Pad

RDX148

• Fitting: Outlet Pad

• Height: 170mm

• Diameter: 64mm

To suit Jaguar XJ V8

2001 >

• Fitting: Inlet 3/8” No. 6 MIOR

RDX142

• Fitting: Outlet 3/8” No. 6 FIOR

• Height: 173mm

• Diameter: 74mm

• 1 x switch port

To suit Jaguar XJ40

3/1987 - 11/1994

• Fitting: Inlet 3/8” No. 6 MIOR

RDX141

• Fitting: Outlet 3/8” No. 6 FIOR

• Height: 172mm

• Diameter: 74mm

• 1 x switch port outer end

To suit Jaguar XJ6 6 cyl bottle type

• Fitting: Inlet 3/8” No. 6 MIOR

RDX140

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 445mm

• Diameter: 50mm

• 1 x switch port

• To convert to flare use

2 x AFX2640

To suit Jaguar XJ6 6 cyl, XJ12 V12

• Fitting: Inlet Pad

RDX147

• Fitting: Outlet Pad

• Height: 110mm

• Diameter: 75mm

To suit Jaguar XK8

1999 >

Top Bottom

Top Bottom

Contents Index 425

Receiver Driers to suit JEEP to KENWORTH

• Fitting: Inlet MSL

RDX588

• Fitting: Outlet Pad

• Height: 260mm

• Diameter: 84mm

• M12 x 1.25 switch port

To suit Jeep Cherokee Sports

2000 >

• Fitting: Inlet Pad

RDX587

• Fitting: Outlet Pad

• Height: 265mm

• Diameter: 86mm

• M12 x 1.25 switch port

To suit Jeep Grand Cherokee WG - WJ

6 cyl & V8 6/1999 - 6/2005

• Fitting: Inlet MSL

RDX586

• Fitting: Outlet 5/8” No. 10 MIOR

• Height: 200mm

• Diameter: 85mm

To suit Jeep Grand Cherokee

3/1996 - 7/1999

• Fitting: Inlet 3/8” No. 6 MIOR

RDX585

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 141mm

• Diameter: 76mm

• 1 access port

To suit Jeep Cherokee

1994 - 1996

• Fitting: Inlet 3/8” No. 6 FIOR

RDX467

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 140mm

• Diameter: 101mm

To suit John Deere 5820

2005 >

• Fitting: Inlet 3/8” No. 6 FIOR

RDX526

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 295mm

• Diameter: 76mm

To suit John Deere 20 & 30

2000 >

• Fitting: Inlet 3/8” No. 6 FIOR

RDX522

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 228mm

• Diameter: 102mm

• Sight glass

• Moisture indicator

To suit John Deere

1991 - 1993

• Fitting: Inlet 3/8” No. 6 FIOR

RDX510

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 204mm

• Diameter: 101mm

• 2 way sight glass

To suit John Deere 9650STS, 9750 STS, CTS 11

• Fitting: Inlet 3/8” No. 6 MIOR

RDX401

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 257mm

• Diameter: 70mm

• H.P.R.V. left of inlet

• 1 x switch port on top

• Sight glass on right of inlet

To suit Kenworth Truck

• Fitting: Inlet 3/8” No. 6 MIOR

RDX402

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 257mm

• Diameter: 70mm

• H.P.R.V. right of inlet

• 1 x switch port left of inlet

To suit Kenworth Truck

Contents Index

426

Receiver Driers to suit KENWORTH to KIA

• Fitting: Inlet 3/8” No. 6 MIOR

RDX514

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 277mm

• Diameter: 70mm

• 1 x access valve on top

• H.P.R.V. left of inlet

• Pressure Switch PSX027

(not included)

To suit Kenworth Truck

• Fitting: Inlet 3/8” No. 6 FIOR

RDX524

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 256mm

• Diameter: 76mm

• Moisture indicator

To suit Kenworth Truck

• Fitting: Inlet 3/8” No. 6 MIOR

RDX527

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 245mm

• Diameter: 76mm

• Pressure Switch PSX027

(not included)

To suit Kenworth Truck

• Fitting: Inlet Pad

RDX476

• Fitting: Outlet Pad

• Height: 146mm

• Diameter: 60mm

• Sight glass

• 2 x switch ports

To suit Kia Carnival

• Fitting: Inlet M20 x 1.5 MIOR

RDX492

• Fitting: Outlet M16 x 1.5 MIOR

• Height: 195mm

• Diameter: 60mm

To suit Kia Optima

5/2001 - 2/2003

• Fitting: Inlet M18 x 1.5 MIOR

RDX311

• Fitting: Outlet M18 x 1.5 MIOR

• Height: 195mm

• Diameter: 60mm

• Pilot Hole: 9.5mm

• Metric

To suit Kia Pregio

7/2002 >

RDX0040

• Length: 230mm

To suit Kia Rio

2005 >

• Fitting: Inlet Pad

RDX491

• Fitting: Outlet Pad

• Height: 250mm

• Diameter: 40mm

To suit Kia Rio

9/2002 >

• Fitting: Inlet Pad

RDX476

• Fitting: Outlet Pad

• Height: 146mm

• Diameter: 60mm

• Sight glass

• 2 x switch ports

To suit Kia Shuma

4/2000 - 5/2001

• Fitting: Inlet M18 x 1.5 MIOR

RDX461

• Fitting: Outlet M18 x 1.5 MIOR

• Height: 202mm

• Diameter: 60mm

• 8.7mm Pilot

To suit Kia Sportage

1/1996 - 4/2000

Top Bottom

Contents Index 427

Receiver Driers to suit KOMATSU to LAND ROVER

• Fitting: Inlet Pad

RDX529

• Fitting: Outlet Pad

• Height: 255mm

• Diameter: 60mm

To suit Komatsu PC300-6, PC1250, PC1800,

PC2000 Excavator, D375 Bulldozer

• Fitting: Inlet Pad

RDX529

• Fitting: Outlet Pad

• Height: 255mm

• Diameter: 60mm

To suit Komatsu HD465, HD785 Dump Truck

WA500, WA900 Wheel Loader

• Fitting: Inlet 3/8” No. 6 MIOR

RDX400

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 154mm

• Diameter: 76mm

To suit Kysor KA300 Roof Top System

• Fitting: Inlet 3/8” No. 6 MIOR

RDX027

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 200mm

• Diameter: 63mm

To suit Kysor Rooftop Unit

• Fitting: Inlet 3/8” No. 6 MIOR

RDX061

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 168mm

• Diameter: 76mm

• H.P.R.V. right of inlet

• 1 x switch port left of inlet

To suit Kysor Rooftop Unit

RDX6711To suit Land Rover Freelander

11/2000 >

• Diameter: 40mm

• Height: 295mm

• Fitting: Inlet Pad

RDX6710

• Fitting: Outlet Pad

• Height: 190mm

• Diameter: 60mm

To suit Land Rover Freelander

2/1998 - 11/2000

• Fitting: Inlet 3/8” No. 6 MIOR

RDX261

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 225mm

• Diameter: 64mm

• 1 x access port

To suit Land Rover Discovery

1997 >

• Fitting: Inlet Pad

RDX284

• Fitting: Outlet Pad

• Height: 185mm

• Diameter: 60mm

• R134a system

To suit Land Rover Discovery

4/1994 - 2/1999

• Fitting: Inlet Pad

RDX223

• Fitting: Outlet Pad

• Height: 165mm

• Diameter: 60mm

To suit Land Rover Discovery

3/1993 - 4/1994

Contents Index

428

Receiver Driers to suit LAND ROVER to MASSEY FERGUSON

• Fitting: Inlet 3/8” No. 6 MIOR

RDX260

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 212mm

• Diameter: 64mm

• 2 x access ports

To suit Land Rover Discovery

3/1991 - 12/1993

RDX0070

• Length: 230mm

To suit Lexus GS300 10/1997 - 11/2000

IS250 11/2005 - 10/2008

RDX0050

• Length: 225mm

To suit Lexus IS300 8/2001 - 11/2005

Lexus IS200 3/1999 - 11/2005

RDX0070

• Length: 230mm

To suit Lexus LS430 11/2000 - 9/2003

Lexus RX330 4/2003 - 2/2006

• Fitting: Inlet 3/8” No. 6 FIOR

RDX532

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 220mm

• Diameter: 76mm

To suit Mack Quantum

• Fitting: Inlet 3/8” No. 6 MIOR

RDX401

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 257mm

• Diameter: 70mm

• H.P.R.V. left of inlet

• 1 x switch port on top

• Sight glass on right of inlet

To suit Mack Truck

• Fitting: Inlet 3/8” No. 6 MIOR

RDX534

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 257mm

• Diameter: 76mm

• H.P.R.V.

• Moisture Indicator

To suit Mack Truck

• Fitting: Inlet 3/8” No. 6 MIOR

RDX531

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 225mm

• Diameter: 76mm

• Service port

• Moisture indicator

• High pressure relief valve

To suit Mack Ultraliner

• Fitting: Inlet 3/8” No. 6 MF

RDX006

• Fitting: Outlet 3/8” No. 6 MF

• Height: 184mm

• Diameter: 64mm

• 1 x switch port left of inlet

To suit Massey Ferguson Tractor

• Fitting: Inlet 3/8” No. 6 MF

RDX031

• Fitting: Outlet 3/8” No. 6 MF

• Height: 167mm

• Diameter: 76mm

• 1 x switch port left of inlet

To suit Massey Ferguson Tractor

Contents Index 429

Receiver Driers to suit MASSEY FERGUSON to MAZDA

• Fitting: Inlet 3/8” No. 6 MIOR

RDX402

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 257mm

• Diameter: 70mm

• 1 x switch port right of inlet

To suit Massey Ferguson Tractor

• Fitting: Inlet 3/8” No. 6 MIOR

RDX521

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 215mm

• Diameter: 76mm

• 1 x access port

To suit Massey Ferguson Tractor

• Fitting: Inlet 3/8” No. 6 MIOR

RDX525

• Fitting: Outlet 3/8” No. 6 FIOR

• Height: 215mm

• Diameter: 66mm

To suit Massey Ferguson Tractor

• Fitting: Inlet 3/8” No. 6 MIOR

RDX528

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 235mm

• Diameter: 75mm

• R12 Service port

• Moisture indicator

To suit Massey Ferguson Tractor

• Fitting: Inlet 3/8” No. 6 MIOR

RDX023

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 203mm

• Diameter: 60mm

• Includes binary switch PSX001

• L.P.C.O. 2.0kg/cm² 28.4 psig

• H.P.C.O. 32.0kg/cm² 455.0 psig

on right of inlet

To suit Mazda 121 Series 2 10/1996 - 5/2001

Cooltemp System

• Fitting: Inlet Pad

RDX182

• Fitting: Outlet Pad

• Height: 160mm

• Diameter: 60mm

• 2 x switch port

To suit Mazda 121, 323 7/1994 - 3/1996

Mazda 929 1994 - 1995

• Fitting: Inlet Pad

RDX601

• Fitting: Outlet Pad

• Height: 163mm

• Diameter: 60mm

• 1 x switch port

• Pressure switch to suit: PSX039

To suit Mazda 121

1992 - 1994

• Fitting: Inlet 5/16” No. 5 MIOR

RDX086

• Fitting: Outlet 5/16” No. 5 MIOR

• Height: 189mm

• Diameter: 67mm

• 1 x switch port

To suit Mazda 121 3/1987 - 11/1990, Mazda 323 10/1980 - 8/1989

626 & MX6 2/1983 - 10/1987, Mazda RX7 Ser 3 & 4 3/1984 - 2/1992

• Fitting: Inlet Pad

RDX600

• Fitting: Outlet Pad

• Height: 161mm

• Diameter: 60mm

• 2 x switch ports

To suit Mazda 121

11/1990 - 10/1994

• Fitting: Inlet Pad

RDX280

• Fitting: Outlet Pad

• Height: 175mm

• Diameter: 48mm

To suit Mazda 3 2.0 & 2.3L 4 cyl

1/2004 - 7/2006

Contents Index

430

Receiver Driers to suit MAZDA

• Fitting: Inlet Pad

RDX223

• Fitting: Outlet Pad

• Height: 165mm

• Diameter: 60mm

• 1 x switch port

To suit Mazda 323

1993 - 5/1994

• Fitting: Inlet Pad

RDX182

• Fitting: Outlet Pad

• Height: 160mm

• Diameter: 60mm

• 2 x switch port

To suit Mazda 323 Astina

8/1998 - 3/2004

• Fitting: Inlet Pad

RDX477

• Fitting: Outlet Pad

• Height: 148mm

• Diameter: 60mm

• 1 x switch ports

To suit Mazda 323 Astina

1/1997 >

• Fitting: Inlet Pad

RDX612

• Fitting: Outlet Pad

• Height: 148mm

• Diameter: 60mm

• 1 x switch ports

To suit Mazda 323 Astina

10/1989 - 11/1996

• Fitting: Inlet Pad

RDX180

• Fitting: Outlet Pad

• Height: 164mm

• Diameter: 61mm

• 2 x switch ports

To suit Mazda 323 Astina 8/1989 - 1/1994

626 1990 - 1993

• Fitting: Inlet Pad

RDX182

• Fitting: Outlet Pad

• Height: 160mm

• Diameter: 60mm

• 2 x switch port

To suit Mazda 323 Protege BJ 1.6L

9/1998 - 3/2004

• Fitting: Inlet 5/16” No. 5 MIOR

RDX022

• Fitting: Outlet 5/16” No. 5 MIOR

• Height: 200mm

• Diameter: 63.5mm

• 2 x switch ports

To suit Mazda 323, 626 Early

RX7 1979 - 1988

RDX0050

• Length: 225mm

To suit Mazda 6

8/2002 >

• Fitting: Inlet 5/16” No. 5 MIOR

RDX190

• Fitting: Outlet 5/16” No. 5 MIOR

• Height: 120mm

• Diameter: 64mm

To suit Mazda 626

8/1997 - 4/2002

• Fitting: Inlet Pad

RDX182

• Fitting: Outlet Pad

• Height: 160mm

• Diameter: 60mm

• 2 x switch port

To suit Mazda 626

9/1994 - 6/1997

Contents Index 431

Receiver Driers to suit MAZDA

• Fitting: Inlet Pad

RDX087

• Fitting: Outlet Pad

• Height: 162mm

• Diameter: 60mm

• 2 x switch ports

To suit Mazda 626 & MX6 GE V6 9/1991 - 8/1994

929 4/1991 - 8/1993, Mazda MX5 1991 - 1994

• Fitting: Inlet Pad

RDX181

• Fitting: Outlet Pad

• Height: 165mm

• Diameter: 61mm

• 2 x switch ports

To suit Mazda 626 GD 6/1990 - 12/1991

929 V6 5/1990 - 1991

• Fitting: Inlet M16 x 1.5 MIOR

RDX089

• Fitting: Outlet M16 x 1.5 MIOR

• Height: 204mm

• Diameter: 60mm

• 2 x switch ports

• Metric

• With Diesel Kiki compressor

To suit Mazda 626 GD, GV Wagon 10/1987 - 5/1995

929 HC V6 5/1987 - 5/1991

• Fitting: Inlet 3/8” No. 6 MIOR

RDX025

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 203mm

• Diameter: 60mm

• 2 x switch ports

To suit Mazda 626 GC, MX-6 6/1985 - 10/1987

929 HB 6/1985 - 10/1987

• Fitting: Inlet Pad

RDX182

• Fitting: Outlet Pad

• Height: 160mm

• Diameter: 60mm

• 2 x switch port

To suit Mazda 929

1994 - 1995

• Fitting: Inlet Pad

RDX087

• Fitting: Outlet Pad

• Height: 162mm

• Diameter: 60mm

• 2 x switch ports

To suit Mazda 929

4/1991 - 8/1993

• Fitting: Inlet Pad

RDX191

• Fitting: Outlet Pad

• Height: 151mm

• Diameter: 60mm

• Includes pressure switch

(PSX081)

To suit Mazda B Series

11/2002 >

• Fitting: Inlet Pad

RDX281

• Fitting: Outlet Pad

• Height: 159mm

• Diameter: 60mm

To suit Mazda B Series B2600

12/1994 - 11/2002

• Fitting: Inlet 5/16” No. 5 MIOR

RDX086

• Fitting: Outlet 5/16” No. 5 MIOR

• Height: 189mm

• Diameter: 67mm

• 1 x switch port

To suit Mazda B Series

6/1985 - 10/1991

• Fitting: Inlet Pad

RDX192

• Fitting: Outlet Pad

• Height: 165mm

• Diameter: 60mm

• Includes pressure switch

(PSX081)

To suit Mazda BT50 M/T

11/2006 >

Contents Index

432

Receiver Driers to suit MAZDA

RDX0070

• Length: 230mm

To suit Mazda CX-9

12/2007 >

• Fitting: Inlet Pad

RDX5810

• Fitting: Outlet Pad

• Height: 160mm

• Diameter: 60mm

• Switch Port: M11 x 1.0

To suit Mazda E2500

1/2001 >

RDX0050

• Length: 225mm

To suit Mazda MPV

8/1999 - 11/2003

• Fitting: Inlet Pad

RDX281

• Fitting: Outlet Pad

• Height: 159mm

• Diameter: 60mm

To suit Mazda MPV

1993 - 1996

• Fitting: Inlet Pad

RDX604

• Fitting: Outlet Pad

• Height: 165mm

• Diameter: 60mm

To suit Mazda MX5

11/1993 - 4/1998

• Fitting: Inlet Pad

RDX283

• Fitting: Outlet Pad

• Height: 158mm

• Diameter: 60mm

To suit Mazda MX5 1/1992 - 6/1993

RX7 1/1992 - 6/1994

• Fitting: Inlet Pad

RDX087

• Fitting: Outlet Pad

• Height: 162mm

• Diameter: 60mm

• 2 x switch ports

To suit Mazda MX5

1991 - 1994

• Fitting: Inlet Pad

RDX161

• Fitting: Outlet Pad

• Height: 150mm

• Diameter: 60mm

To suit Mazda MX5

8/1989 - 1991

• Fitting: Inlet Pad

RDX182

• Fitting: Outlet Pad

• Height: 160mm

• Diameter: 60mm

• 2 x switch ports

To suit Mazda Premacy 1.8 & 2.0L

2/2001 - 6/2003

RDX0070

• Length: 230mm

To suit Mazda RX8

7/2003 >

Contents Index 433

Receiver Driers to suit MAZDA to MERCEDES

• Fitting: Inlet 5/18” No. 10 MIOR

RDX183

• Fitting: Outlet MSL

• Height: 210mm

• Diameter: 89mm

• 1 x access port

To suit Mazda Tribute 2.0, 2.3, 3.0L

2/2001 - 12/2007

• Fitting: Inlet 1/2” No. 8 MIOR

RDX212

• Fitting: Outlet 1/2” No. 8 MIOR

• Height: 295mm

• Diameter: 51mm

To suit Mercedes Benz Truck

• Fitting: Inlet Pad

RDX671

• Fitting: Outlet Pad

• Height: 207mm

• Diameter: 65mm

To suit Mercedes Benz Sprinter W901

• Fitting: Inlet Pad

RDX671

• Fitting: Outlet Pad

• Height: 207mm

• Diameter: 65mm

To suit Mercedes Benz Vito 112 2/2001 - 4/2004

RDX207

• Length: 350mm

To suit Mercedes Benz Vito W639 2003 >

Desiccant Filter Kit to suit CNX799

• Fitting: Inlet 3/8” No. 6 MIOR

RDX205

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 171mm

• Diameter: 75mm

• 3 x switch ports

To suit Mercedes Benz W107 Series, 380SL, 450SLC

W126 V8 some

• Fitting: Inlet 3/8” No. 6 MF

RDX209

• Fitting: Outlet 1/2” No. 8 MF

• Height: 173mm

• Diameter: 75mm

• 1 x switch port

To suit Mercedes Benz W107

380, 450SL, 560SL

• Fitting: Inlet 3/8” No. 6 MF

RDX219

• Fitting: Outlet 1/2” No. 8 MF

• Height: 168mm

• Diameter: 70mm

To suit Mercedes Benz W107

380SL, 450SL, 560SL

• Fitting: Inlet 3/8” No. 6 MF

RDX201

• Fitting: Outlet 3/8” No. 6 MF

• Height: 167mm

• Diameter: 75mm

• 1 x switch port

• 1 x temp. switch port

To suit Mercedes Benz W116 Series

• Fitting: Inlet 3/8” No. 6 MIOR

RDX202

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 172mm

• Diameter: 75mm

• 2 x switch ports

• 1 x temp. switch port

To suit Mercedes Benz W123 Series

W116, 250, 280

Contents Index

434

Receiver Driers to suit MERCEDES

• Fitting: Inlet 3/8” No. 6 MIOR

RDX203

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 171mm

• Diameter: 74mm

• 3 x switch ports

To suit Mercedes Benz W124 Series

300E, 300D

• Fitting: Inlet 3/8” No. 6 MIOR

RDX204

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 173mm

• Diameter: 75mm

• 2 x switch ports

• 1 x temp Switch Port

To suit Mercedes Benz W126 Series

Not V8

• Fitting: Inlet 3/8” No. 6 FIOR

RDX214

• Fitting: Outlet 3/8” No. 6 FIOR

• Height: 188mm

• Diameter: 75mm

• H.P.R.V.

• Male pressure switch port

To suit Mercedes Benz W140 S320

1997 >

• Fitting: Inlet 3/8” No. 6 FIOR

RDX675

• Fitting: Outlet 3/8” No. 6 FIOR

• Height: 195mm

• Diameter: 95mm

To suit Mercedes Benz W140 S320

9/1993 - 4/1999

• Fitting: Inlet 3/8” No. 6 FIOR

RDX213

• Fitting: Outlet 3/8” No. 6 FIOR

• Height: 195mm

• Diameter: 75mm

• H.P.R.V.

• Male pressure switch port

To suit Mercedes Benz W140 400SE/SEL, 500SEL,

S320 3/1992 - 4/1999

• Fitting: Inlet Pad

RDX246

• Fitting: Outlet Pad

• Height: 130mm

• Diameter: 60mm

To suit Mercedes Benz W168 A Class

2/2000 - 7/2001

• Fitting: Inlet 3/8” No. 6 MIOR

RDX218

• Fitting: Outlet Pad

• Height: 85mm

• Diameter: 62mm

• Pressure switch port

To suit Mercedes Benz W168 A Class

7/1997 - 5/2000

• Fitting: Inlet 3/8” No. 6 MIOR

RDX206

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 172mm

• Diameter: 75mm

• 2 x switch ports

To suit Mercedes Benz W201 Series 190

10/1982 - 8/1993

• Fitting: Inlet 3/8” No. 6 FIOR

RDX215

• Fitting: Outlet 3/8” No. 6 FIOR

• Height: 166mm

• Diameter: 75mm

• H.P.R.V.

• 2 x switch ports

To suit Mercedes Benz W202 C Class C180/220

3/1997 - 11/2000

• Fitting: Inlet 3/8” No. 6 FIOR

RDX217

• Fitting: Outlet 3/8” No. 6 FIOR

• Height: 171mm

• Diameter: 75mm

• Pressure relief valve

To suit Mercedes Benz W202, C180, C220

2/1994 - 11/1996

Contents Index 435

Receiver Driers to suit MERCEDES to MITSUBISHI

• Fitting: Inlet 3/8” No. 6 MIOR

RDX930

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 179mm

• Diameter: 75mm

• Sight glass

• Pressure relief valve

To suit Mercedes Benz W210 E230, E240 10/1996 - 8/2002

S210 E230, E240 10/1996 - 3/2003

• Fitting: Inlet Pad

RDX932

• Fitting: Outlet Pad

• Height: 405mm

• Diameter: 45mm

To suit Mercedes Benz W211 E270

3/2002 >

• Fitting: Inlet Pad

RDX671

• Fitting: Outlet Pad

• Height: 207mm

• Diameter: 65mm

To suit Mercedes Benz W220 S Class

10/1998 >

• Fitting: Inlet Pad

RDX907

• Fitting: Outlet Pad

• Height: 160mm

• Diameter: 64mm

• 1 x switch port

To suit MG MGF 1.8L Convertible

2/1997 - 9/2002

RDX6711To suit Mini Cooper R50, R56

3/2002 >

• Fitting: Inlet 3/8” No. 6 MF

RDX001

• Fitting: Outlet 3/8” No. 6 MF

• Height: 203mm

• Diameter: 60mm

• 2 x switch ports

To suit Mitsubishi Colt RA - RE

1/1981 - 5/1990

• Fitting: Inlet 3/8” No. 6 MIOR

RDX027

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 200mm

• Diameter: 63mm

• 2 x switch ports

To suit Mitsubishi Cordia,

Galant, Nimbus

• Fitting: Inlet Pad

RDX606

• Fitting: Outlet Pad

• Height: 250mm

• Diameter: 67mm

To suit Mitsubishi Delica

1/1995 >

• Fitting: Inlet Pad

RDX608

• Fitting: Outlet Pad

• Height: 186mm

• Diameter: 60mm

• Switch Port 3/8” x 24UNF

To suit Mitsubishi Express Van SH 1/1994 - 1/2003

Starwagon SH - WA 9/1991 - 11/1996

• Height: 295mm

• Diameter: 40mm

RDX0070To suit Mitsubishi 380

• Length: 230mm

9/2005 - 9/2008

Contents Index

436

Receiver Driers to suit MITSUBISHI

• Fitting: Inlet Pad

RDX628

• Fitting: Outlet Pad

• Height: 232mm

• Diameter: 67mm

• 1 x switch port

To suit Mitsubishi Fighter FK617 & FK618

11/1997 - 1/2005

• Fitting: Inlet 3/8” No. 6 MIOR

RDX021

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 203mm

• Diameter: 60mm

• Includes binary switch

PSX058 left of inlet

• L.P.C.O. 2.0kg/cm² 28.4 psig

• H.P.C.O. 24.0kg/cm² 342.0 psig

To suit Mitsubishi Galant HG - HH

11/1988 - 11/1992

• Fitting: Inlet Pad

RDX621

• Fitting: Outlet Pad

• Height: 188mm

• Diameter: 60mm

• With pressure switch: PSX030

To suit Mitsubishi Galant ST

RDX0070

• Length: 230mm

3/2005 >

To suit Mitsubishi Grandis 2.4L

• Fitting: Inlet Pad

RDX220

• Fitting: Outlet Pad

• Height: 164mm

• Diameter: 61mm

• 2 x switch ports

To suit Mitsubishi L300 Express

4/1995 >

RDX606

• Fitting: Inlet Pad

• Fitting: Outlet Pad

• Height: 250mm

• Diameter: 67mm

12/1994 - 11/2003, Starwagon WA 9/1994 - 5/2004

To suit Mitsubishi L300 SJ Dual System

• Fitting: Inlet 5/16” No. 5 MIOR

RDX022

• Fitting: Outlet 5/16” No. 5 MIOR

• Height: 200mm

• Diameter: 60mm

• 2 x switch ports

To suit Mitsubishi L300

4/1980 - 10/1986

• Fitting: Inlet Pad

RDX412

• Fitting: Outlet Pad

• Height: 191mm

• Diameter: 61mm

• M11 x 1.0 switch port

To suit Mitsubishi L400 WA

12/1994 - 3/2006

• Fitting: Inlet Pad

RDX5310

• Fitting: Outlet Pad

• Height: 230mm

• Diameter: 40mm

To suit Mitsubishi Lancer CJ

10/2007 >

• Fitting: Inlet 3/8” No. 6 MIOR

RDX030

• Fitting: Outlet 3/8” No. 6 MIOR

• Height: 182mm

• Diameter: 63mm

• 1 x switch port

• 1 x access port right of inlet

To suit Mitsubishi Express Van SF - SJ

10/1986 - 7/2008

Contents Index 437

Receiver Driers to suit MITSUBISHI

• Fitting: Inlet Pad

RDX623

• Fitting: Outlet Pad

• Height: 192mm

• Diameter: 60mm

• Switch Port 3/8” x 24UNF

To suit Mitsubishi Lancer CE

10/1999 - 11/2004

• Fitting: Inlet Pad

RDX621

• Fitting: Outlet Pad

• Height: 188mm

• Diameter: 60mm

• With pressure switch: PSX030

To suit Mitsubishi Lancer CE

7/1996 - 3/2003

• Fitting: Inlet Pad

RDX608

• Fitting: Outlet Pad

• Height: 186mm

• Diameter: 60mm

• 1 x switch port

To suit Mitsubishi Lancer CC 12/1994 - 12/1995

Lancer CE 10/1998 - 7/2004

• Fitting: Inlet Pad

RDX603

• Fitting: Outlet Pad

• Height: 166mm

• Diameter: 60mm

• 2 x switch ports

To suit Mitsubishi Lancer CC Sedan/Wagon

9/1992 - 7/1996

• Fitting: Inlet 5/16” No. 5 MIOR

RDX022

• Fitting: Outlet 5/16” No. 5 MIOR

• Height: 200mm

• Diameter: 60mm

• 2 x switch ports

To suit Mitsubishi Lancer CC

9/1992 - 7/1996

• Fitting: Inlet 5/16” No. 5 MIOR

RDX086

• Fitting: Outlet 5/16” No. 5 MIOR

• Height: 189mm

• Diameter: 67mm

To suit Mitsubishi Lancer CC 9/1992 - 12/1995

Magna TM - TP 4/1985 - 7/1991

• Fitting: Inlet 5/16” No. 5 MIOR

RDX408

• Fitting: Outlet 5/16”