Dicks Oilfield Satellite Auto Driller

THE

SATELLITEAUTOMATIC DRILLING

CONTROL SYSTEM

U S E D

W O R L D -W I D E

l

l

l

l

l

SAVES TIME and MONEY

REDUCED DRILLING COST PER FOOT

INCREASED RATE OF PENETRATION

LONGER BIT LIFE

STRAIGHTER HOLE

AUTOMATIC BIT WEIGHT

CONTROL SYSTEM

Automatic Bit Weight Control Systemwww.dicksoilfield.com

Oilfield InstrumentsSales & Service

CUT COSTS WITH THE SATELLITEAUTOMATIC DRILLING CONTOL SYSTEM

The realization that constant, precise weight control is a

critical factor in drilling efficiency, has led modern drilling tech-

niques toward automation. It is universally recognized that

manual operation - however skillful - is unable to keep this vital

weight control within the required limits throughout an entire

drilling program.

Every deviation from the optimum weight on the bit for a

given formation increases the cost of making hole. Uncontrolled

bit-weight variations adversely affect hole straightness, penetra-

tion rate and bit life.

Satellite Automatic Drilling Control - unique in conception

with its two-speed differential Gear Unit for regular and high

speed drilling and its Comparative Weight Indicator for sensitive

visual control-has proven itself accurate, reliable and safe during

thousands of hours of trouble-free performance on all kinds of

rigs and under all drilling conditions.

Simple to install and simple to maintain, the Satellite will, for

years, go on making hole better and faster than by any other

means, manual or otherwise, and the minutes it saves tour after

tour grow to hours and days and weeks. Thus, it not only rapidly

pays for itself, but keeps paying dividends in time saved, longer

bit life, reduced wear and tear on the rig and improved overall

efficiency.

AUTOMATIC DRILLING CONTROL SYSTEMODESSA, TEXAS - 432-381-6565

Control originates in the Satellite pneumatic deadline diaphragm (fig. 1) or in a hydraulic tie-down anchor (fig. 2) which senses the deadline tension and reacts to its variations.

These reactions are relayed to the bourdon tube of the Controller Unit where they are continuously and automatically compared with a pre-set point, corresponding to the desired weight on the bit.

When that weight, reflected in increased deadline tension, falls below the set point, the Controller opens a valve to allow air to be fed to the Air Motor.

Rotated by the Air Motor, through the two-speed differen-tial Gear Unit, the lift line reel reels in a wire line attached to the brake lever of the drawworks.

It raises this lever and permits the drum to rotate and to feed off drilling line.

This increases the weight on the bit and reduces the tension in the deadline.

The instant the drum starts moving, it rotates a rubber friction wheel against the inside of the drum spool. This rotation is transferred by flexible shaft, as a reverse force, to the differential Gear Unit. There, it overrides the action of the Air Motor and lowers the brake lever by gradually unreeling the lift line. When the weight on the bit and the tension in the deadline have resumed their initial relationship, the Controller Unit closes the valve to the Air Motor. The brake is fully applied. The cycle is completed.

SAVES TIME AND MONEY

(fig. 1) (fig. 2)

A

B

C

D

SATELLITE AUTOMATIC DRILLER..The principle of the Satellite Driller is based on the relationship between weight on bit and total hook load. Any variation in one causes an inverse variation in the other.

The purpose of the Satellite Driller is to maintain a constant predetermined bit weight in order to obtain optimum drilling efficiency.

l

l

l

l

l

l

Maintains a predetermined weight on bit to drill quickly, efficiently.

Compensates for worn, imperfect or wet brake linings for consistent, on target performance.

Two-speed gear unit covers widest range of penetration rates.

Smooth, gradual opening and throttling of the air valve provides sensitive, precise bit weight control.

No electrical components - safe operation in explosive atmosphere.

Rugged construction - years of trouble-free service.

1.Precise bit weight control originates direct from

the Martin-Decker weight indicator system which continuously monitors any change in weight. Weight signals are simultaneously displayed and relayed to the Satellite controller unit.

2.Activated by the air motor through a two-

speed differential gear unit, the lift-line raises the drawwork's brake lever, this allows the drum to rotate, feed off drill line and increase weight on bit.

FEATURES . . .

Unlimited Brake Lever stroke

Two-speed Gear Unit

Gradualness in opening and throttling of the Air Valve

Absence of electrical components

Rugged construction

compensates for worn, imperfect, or wet linings as well as worn brake linkages. No piston or linkage type system can adjust to these deficiencies.

covers widest range of penetration rates.

gives smooth, sensitive response.

provides safe operation in explosive atmospheres.

assures years of trouble free operation.

SCHEMATIC DIAGRAM

CONTROLLER

HYDRAULIC LINE

RIG AIR IN

AIR LINE

. . . The Driller's Edge.

DRUM SPOOL

LIFT LINE

FLEX SHAFT

ROTATIONSEDNSOR SPRING

TENSION

DIFFERENTIAL GEAR

AIR MOTOR

BRAKE LEVER

3.The bourdon tube in the controller unit reacts

to weight changes and, in turn, continuously compares actual bit weight with the preset desired bit weight.

When the desired bit weight falls below the set point, the controller opens a valve which regu-lates air flow to the air motor.Satellite Driller differential gear unit with lift line reel.Break lever with lift line attached.Driller's console with Satellite Driller installed.

4.By means of a friction wheel riding against the

drum spool, the drum rotation is transferred as a reverse force back to the differential gear unit. This force overrides the air motor action, gradu-ally releases the lift-line and allows the drawwork's brake to be applied.

When the actual bit weight reaches the desired weight set point, the controller closes the air motor valve and the brake is fully applied.

PANEL MOUNT CONTROLLER BULK MOUNT CONTROLLER

DRUM SENSOR 2-SPEED MOTOR



INSTRUMENTATION CATALOG

HOW TO ORDER

MODEL 40 (AT101)

MODEL 30 (AT108)

• SPECIFY PANEL OR BOX MOUNT

• SPECIFY SINGLE LINE LOAD

• SPECIFY ANCHOR USED

• SPECIFY WIRELINE SIZE

• SPECIFY GAUGE SIZE (12" OR 16")

• 40,000 LB SINGLE LINE LOAD

• 12" OR 16" INDICATOR

• DIAL CONFIGURATION 4/6 8/10

• USES CC104 COMPRESSION L/C


• 8.5" OR 12" INDICATOR

• DIAL CONFIGURATION 4/6/8


ANCHOR TYPE

MODEL 150 (AT 111)

MODEL 125 (AT110)

MODEL 100 (AT104)

MODEL 75 (AT103)

MODEL 50 (AT102)

WAGNER INSTRUMENTATION 2000's anchor type weight indicators are designed for accurate indication of hook load and weight on bit. Our weight indicators are designed to work with all major deadline anchors using either tension or compression loadcells. Panel mount and box mount systems are available in English and Metric divisions. Each system is comprised of a tough diaphragm type loadcell, high pressure hose assy with disconnects, 12" or 16" indicator with complete dial set, and damper assy to dampen extreme shock and excessive pointer movement during tough drilling situations.












• USES CC106 COMPRESSION L/C OR

• TC100 TENSION L/C











WEIGHT INDICATORS

DRILLING RIG INSTRUMENTATIONANCHOR TYPE WEIGHT INDICATORSFOR THE LARGEST RIGS

Type E/Series AWE with deadline loads of 75,000 Ib.for 6, 8, 10 and 12 lines strung.

Type EB/Series AWE with deadline loads of 100,000 Ib.for 8, 10, 12 and 14 lines strung.*

Type 125/Series AWE with deadline loads of 125,000 Ib.for 8,10,12 and 14 lines strung.*

Type 150/Series AWE with deadline loads of 150,000 Ib.for 10, 12, 14, and 16 lines strung.**

Type 200/Series AWE with deadline loads of 200,000 Ib.for 10,12, 14, and 16 lines strung.

*Optional 16 lines on request **Optional 8 lines on request

New Stainless Steel Driller's Panel 1 A10600A, with space for six gauges or meters plus weight indicator.

Type E (typical) AWE Series Weight Indicator

• Helps driller maintain consistent weight on bit to drill faster, more efficiently and more economically.

• Available as separate unit or, for greater convenience, mounted in driller's console with a choice of the following instruments: mud pump pressure gauge, mud pump stroke meter (SPM), rotary table meter (RPM), electric torque meter, tong-torque gauge, automatic driller.

• Cuts down on time consuming fishing jobs; detects stuck pipe, tight holes.

• Gauge consists of: outer dial for direct reading of weight on bit, inner dial for total hook load.

• Equipped with vernier bit weight indicator for 4:1 sensitivity, greater accuracy.

• Anchor secures deadline, with load cell mounted in anchor to produce precise weight signals. These signals are transmitted instantly to the gauge mounted in front of the driller.

• Compatible with either National or Hercules deadline anchors.

ANCHOR TYPE WEIGHT INDICATORSFOR LARGE RIGS

ANCHORS FOR E, EB, 125 & 150 WEIGHTINDICATOR SYSTEMS

The National Type EB, for Type E or Type EB Weight Indicators, with E80 Tension Load Sensor. Mounts on floor or substructure. Type E System designed for 1-1/4", 1-3/8", and 1-1/2" wireline sizes. Type EB Systems designed for 1-1/2" and 1-5/8" wireline sizes. Drum diameter 28". Net weight 1560 Ib.***

The Hercules Model HA 131T, for Type E or Type EB Weight Indicators, with E80 Tension Load Sensor. Mounts on floor or substructure. Type E System designed for 1-1/4", 1-3/8", and 1-1/2" wirelines. Type EB Systems designed for 1-1/2" and 1-5/8" wirelines. Drum diameter 28". Net weight 1460 Ib.**

The Hercules Model HA 120T, for Type E or EB Weight Indicators, with E551 Compression Load Sensor. Designed for 1-1/4", 1-3/8", 1-1/2" and 1-5/8" wirelines. Drum diameter 28". Net weight 1475 Ib.***

The Hercules Model HA 130T, for Type 125 Weight Indicator, with E551 Compression Load Sensor. Designed for 1-1/2", 1-5/8" and 1-3/4" wirelines. Drum diameter 31". Net weight 2200 Ib.***

The Hercules Model HA 150T, for Type 150 Weight Indicator with E551 Compression Load Sensor. Designed for 1-5/8", 1-3/4", 1-7/8" and 2" wireline sizes. Drum diameter 36". Net weight 3050 Ib.******Wireline size must be specified when ordering.

• Systems available in pound, kilogram and decaNewton models.

• System consists of weight indicator and wireline anchor with load sensor.

To order: Specify size of rig, derrick capacity in pounds, size of drilling wireline, number of lines strung.

ANCHORS FOR D WEIGHTINDICATOR SYSTEMS

The National Type D, for Type D Weight Indicator, with E80 Tension Load Sensor. Mounts on floor or substructure. Designed for 1", 1-1/8" and 1-1/4" wireline sizes. Drum diameter 24". Net weight 1080 Ib.**

The Hercules Model HA 129T, for Type D Weight Indicator, with E80 Tension Load Sensor. Mounts on floor or substructure. Designed for 1", 1-1/8" and 1-1/4" wirelines. Drum diameter 24". Net weight 810 Ib.***

The Hercules Model HA 119T, for Type D Weight Indicator, with E543 Compression Load Sensor. Mounts on floor or substructure. Designed for 1", 1-1/8" and 1-1/4" wireline sizes. Drum diameter 24". Net weight 820 Ib.******Wireline size must be specified when ordering.

TypeEB

ModelHA 131T

ModelHA 120T

ModelHA 130T

ModelHA 150T

Type D

ModelHA 129T

ModelHA 119T

Type D/Series AW with deadline loads of 50,000 Ib. for 6, 8, 10 and 12 lines strung.

Type DAW SeriesWeight Indicator

DEFLECTION TYPE (DT101)

HOW TO ORDER

• WAGNER INSTRUMENTATION 2000's Deflection type weight indicator is ideal for use with small to medium drilling and workover rigs.

• Unit is portable, rugged, and dependable. Ready to be placed on the drill line right out of the box.

• Deflection type load cell may be used on wire line sizes 7/8" - 1 1/4".

• The system comes with self-contained steel box. Weight indicator head is complete with 10 dial set for use with different wire line sizes and lines strung, 25 ft hose assy, and deflection type loadcell with c-clamp.

• Available in English and Metric divisions.

• SPECIFY SINGLE LINE LOAD CAPACITY

• SPECIFY SIZE AND NUMBER OF LINES

• SPECIFY SCALE NEEDED (LBS, KGS, dANS)

MINI WEIGHT INDICATOR (WBD100 )

HOW TO ORDER:

• For use with small drilling and production rigs up to 30,000 Ib single line load.

• System comes with 6" or 8.5" gauge mounted in rugged metal box, 25 ft hose assy with disconnects, and either piston or diaphragm type load cell.

• Available in English and Metric divisions.

• Dual dial faces available. Common reeving pat-terns of 2/4, 4/6, 6/8.

• Load cell attaches to rig floor with a universal clevis or shackles which eliminates the use of an anchor.

• SPECIFY RIG SIZE AND NUMBER OF LINES STRUNG

• SPECIFY SCALE NEEDED

• SPECIFY HOSE LENGTH (25 FT STANDARD)

• SPECIFY TYPE OF LOAD CELL REQUIRED

WEIGHT INDICATORS

ROTARY TORQUE SYSTEMS

TONG TORQUE SYSTEMS

ROTARY TORQUE SYSTEM-CHAIN (RT100)

HOW TO ORDER

• WAGNER INSTRUMENTATION 2000's Rotary torque system is designed to help the driller during coring, milling, and reaming operations. The system also helps avoid twist-offs and increases bit life by showing the driller when the drill string is torquing to unsafe levels.

• System is comprised of 6" fluid filled gauge with bracket, 2 ft and 14 ft hose assys with disconnects, and idler assy with wheel

• Systems available in box and panel mount versions

• Gauge capacities measured in points and are a relative indication of torque

• SPECIFY CHAIN SIZE OR WHEEL

• SPECIFY 500 POINT OR 1000 POINT GAUGE


• LENGTH OF HOSES (IF OTHER THAN STANDARD LENGTHS)

UNIVERSAL TONG LINE PULL (TT100)

HOW TO ORDER

• Systems are designed to give accurate readings for makeup and breakout torque.

• System comprised of 6" fluid filled gauge with bracket, 25 ft hose assy, and tension cylinder with shackles

• Systems available in box mount and panel mount versions

• Capacities up to 25,000 Ibs

• Available in Ibs, kgs, and in dual scale configurations

• SPECIFY CAPACITY AND SCALE NEEDED (ENGLISH OR METRIC)

• PANEL OR BOX MOUNT

POWER TONG SYSTEMS (TT101)

• Systems are designed to indicate accurate torque on each joint of pipe

• System comprised of 6" fluid filled gauge with bracket, 5 ft hose assy cylinder type or compression load cell, and shackles if required

• Systems available in box mount and panel mount versions

• Available in ft/lbs, kg/m, and dual scale configurations

HOW TO ORDER

• SPECIFY CAPACITY AND HANDLE LENGTH

• SPECIFY TYPE AND SIZE OF LOAD CELL NEEDED


• LENGTH OF HOSE (STANDARD HOSE LENGTH IS 5 FT)

SINGLE POINTER (MG100)

HOW TO ORDER

• WAGNER INSTRUMENTATION 2000'S single pointer mud pressure system is designed to read pressure up to 15,000 psi. The system uses 1502 and 2202 hammer unions with diaphragm protec-tors, piston isolators, or deboosters to separate mud, cement, and the like from system internal parts.

• Gauge fluid filled and calibrated 360°

• Standard capacities 3,000 psi, 5,000 psi, 6,000 psi, 10,000 psi, and 15,000 psi along with their metric equivalents

• Available in box and panel mount versions

• Hose lengths up to 50 ft

• SPECIFY CAPACITY & LENGTH OF HOSE

• SPECIFY BOX OR PANEL MOUNT

• SPECIFY TYPE OF SENSOR

4:1 COMPOUND (MG101)

HOW TO ORDER

• The dual pointer mud pressure system is designed to read pressure up to 16,000 psi. The dual movement allows for monitoring large and small pressure changes. The unit is primarily used on service trucks used in high pressure cementing and fracturing.

It uses rugged diaphragm protectors, 1:1 piston isolators, and 4:1 deboosters to separate drilling mud, chemicals, and cement from the internal parts of the system.

• Gauge fluid filled and calibrated 360° with second-ary 4:1 pointer showing smaller pressure changes

• Standard capacities 4,000 psi, 8,000 psi, 12,000 psi, 16,000 psi and their metric equivalents

• Available in box and panel mount versions

• Hose lengths up to 50 ft

• SPECIFY CAPACITY OF SYSTEM AND HOSE LENGTH

• SPECIFY TYPE OF SENSOR


•

MUD PRESSURE SYSTEMS

DRILLING RECORDER (WDR)

HOW TO ORDER

• WAGNER INSTRUMENTATION 2000's Drilling Recorder is a tough, reliable drill floor recorder which is designed to monitor 6 to 7 different functions.

• The recorder is completely mechanical, no electrical power is needed.

• Chart drive is run by a durable 12 hour or 24 hour clock assy.

• Impulses are recorded clearly by self-contained ball point pens while a high grade carbon paper records a duplicate copy.

• The unit is easily operated and maintained with on-site personnel.

• The recorder is easily hooked up to existing instrumentation through the use of high-quality disconnects.

• SPECIFY THE NUMBER OF FUNCTIONS TO BE RECORDED AND WHAT THE FUNCTIONS ARE

• SPECIFY TYPE OF WEIGHT INDICATOR USED AND WHETHER THE WTIND IS ANCHOR OR DIAPHRAGM TYPE

• SPECIFY PUMP PRESSURE CAPACITY

• SPECIFY ROTARY TABLE TYPE-CHAIN DRIVEN OR TOP DRIVE

PRESSURE RECORDERS (R100)

HOW TO ORDER

Rugged & dependable 1,2, & 3 pen recorders to record weight, torque, and pressures up to 16,000 psi.

• 6" fluid filled gauges are used in the recorders which makes operation and maintenance a breeze.

• Recorder tubes use a standard 6" tube assy for ease of maintenance and calibration

• Standard 12" chart paper is used along with disposable felt tip pens

• Metric equivalents are available

• Manual wind and multi-speed electric clocks available

• SPECIFY PRESSURE RANGE OR CAPACITY TO BE RECORDED

• SPECIFY TYPE OF CLOCK & SPEED

• SPECIFY WALL MOUNT OR PORTABLE

RECORDERS

FAST, EASY LOAD CONTROL FOR SERVICE UNITS.

THREE CONFIGURATIONS THAT MEASURE UP.

The easiest/ most versatile way for a well servicing operation to control hook load while running a double-fast-line or swab-bing with a sand line, is with a Hydro-Mast Weight Indicator.

This reliable hydraulic system will read weights of up to 360,000 Ib., whether the deadline is fastened to an anchor, traveling block or crown. It's ideal for any well servicing rig.

The system consists of an indicator, one or two-pad compression-type load cells (depending on the type of mast), intercon-necting hydraulic hoses with quick-disconnect fittings at the gauge end, plus hydraulic fluid for the instrument and a hand pump. It is completely calibrated, sealed at the factory and comes ready to install and use.

When installed, the Hydro-Mast Weight Indicator will detect the slightest weight change. Such activity will cause the com-pression load cell to generate a hydraulic pressure signal which travels through the connecting hose to the Bourdon tube of the gauge. Tube movement drives the single and/or dual pointer indicator.

Type HM-6-1 is a single pad load cell system with a zero-adjust six-inch gauge and adjustable damper. The target pointer can be set for the maximum weight desired. The single load cell senses the total weight of the mast and hook load, and it relays the hydraulic signal to the weight gauge. This system is available in ranges of 0-25,000, 0-50,000, 0-100,000 and 0-150,000 Ib.

Type HM-6-2 is a two-pad load cell system. The indicator has one six-inch gauge with a hook load pointer and adjustable target pointer.

Two smaller gauges provide the weight of each pad to help the operator equally distribute the load. Thus, an integrator provides the signal to the large gauge. Choose from capaci-ties in ranges of: 0-50,000, 0-100,000, 0-150,000 and 0-240,000 Ib.'

Type HM-8-2, also a two-pad system, features a larger 8% inch main gauge which utilizes a zero-adjust dial with two pointers. One pointer indicates hook load while the 4:1 ratio vernier provides a magnified indication of the slightest hook load changes. Capacities are available in ranges of: 0-120,000, 0-150,000, 0-160,000, 0-240,000, 0-300,000 and 0-360,000 Ib.

The Hydro-Mast Weight Indicator provides accurate readings over its long service life. All systems are housed in a heavy-duty steel box with removable front and back doors to protect the gauges during shipment, installation and removal. A two-inch diameter coupling is welded to the bottom of the cabinet for mounting on a pipe stand for increased visibility.

Additionally, these DICKS gauges are fluid-filled to lubricate, prevent rust, soften vibration and avoid fogging.

Contact a Representative for proper application information.

DESIGNED FOR PRECISION, BUILT TO LAST.

DICKS

Hydro-Mast Weight Indicators are available for operations up to 360,000 Ib.

HYDRO-MAST WEIGHT INDICATORS

COMPOUND PRESSUREINDICATOR SYSTEM

GM4 and GM4P Series

Takes the guesswork out of Fracturing, Acidizing, Cementing or Mud Pressure Indication

• Used primarily for monitoring pump pressures on service trucks engaged in cementing, high pressure hydraulic fracturing operations or acidizing operations involving downhole stimulation of oil pay formations.

• Dual dial is ideal for these operations since pressures in these processes range from high to low depending upon the kind of pay formation being treated.

• Compound gauge has two pointers.• Dial has 4:1 vernier reading for indicating small pressure changes, such as

formation breakdown or plugging of perforations, fractures, etc.• Vernier pointer makes four complete revolutions for full capacity of gauge,

giving four times more resolution for same pressure change.• Standard pointer is full 360° sweep of capacity of dial.• System consists of pressure gauge with dual dial, high pressure hose and

diaphragm protector assembly.• Gauge mounts in any convenient location for easy visibility. Usually mounted

near truck mount recorders on service truck.• Fluid-filled gauge dampens most truck vibrations and adjustable damper

controls pump oscillations.• Pulsation damper, located at top of gauge, can be used to reduce pointer

movement to steady, even action.• Pressure gauge receives its signals through high pressure hose from

diaphragm-type protector assembly,• Diaphragm, mounted on any 2" connection, is equipped with rubber cup which

separates pump fluid from hydraulic fluid which actuates the gauge.• May be substituted for standard mud pump pressure gauge (GM6A).• Has all of the advantages of standard pump pressure gauges.• Can be easily recorded on either hydraulic circular recorders or electronic

remote strip recorders.

Pressure Indicating Manifold System with two indicators and gauge protector sensors.

PRESSURE INDICATING MANIFOLD• Provides two indications: annulus pressures and tubing and drill pipe

pressures. Ideal for drill stem testing, cementing or acidizing operations.• Pressure signals relayed to gauge indicators for convenient remote readouts.

Gauges and hoses housed in light carrying case.• Compound vernier-type gauges with long pointer movement provide optimum

resolution of small pressure changes. Capacity is up to 16,000 psi.To order—Specify capacity and application.For additional information request pressure indicating manifold information.

Example: The compound gauge shown here has a 16,000 psi capacity. The inner dial has a yellow pointer which indicates psi; each increment shown represents 1,000 psi. One complete revolution of the inner dial yellow pointer indicates 16,000 psi. The outer dial has a red pointer which indicates psi; each increment shown represents 100 psi. One complete revolution of the outer dial red pointer indicates 4,000 psi.

How the Compound Pressure Indicator works

1,400 PSIInner pointer on 1,red outer pointer on400 = 1,400 psi reading.




FirstThousand

PSI

SecondThousand

PSI

ThirdThousand

PSI

FourthThousand

PSI



3110 FM 1936P.O. Box 69092Odessa, Texas 79769

24 Hour (432) 381-6565Toll Free (877) 381-6565

Fax (432) 381-9428

SALES & RENTAL OF

DRILLING & WELL SERVICE

INSTRUMENTATION

NEW & REBUILT

SATELLITE AUTOMATIC DRILLERS

WEIGHT INDICATORS (All Brands)

FOOTAGE RECORDERS

MARTIN DECKER/EASTMAN

DEVIATION INSTRUMENTS

GAUGES: Pump, SPM,RPM, Torque

PUMP PRESSURE RECORDERS

ROTARY TORQUE SYSTEMS

TONG TORQUE SYSTEMS

SUPPLIES FOR ALL EQUIPMENT

MISCELLANEOUS SUPPLIES

H S APPROVED2FULLY INSURED

Dick GarletsOwner

Bryan HitchcockSales Manager

Dicks Oilfield Satellite Auto Driller

Documents

Transcript of Dicks Oilfield Satellite Auto Driller