DEDICATED MICROMETERS AND CALIPERS
Transcript of DEDICATED MICROMETERS AND CALIPERS
PRE1429
DEDICATED MICROMETERS AND CALIPERS
SMAL
L TO
OL
INST
RUM
ENTS
AN
D DA
TA M
ANAG
EMEN
T
NO MATTER WHAT YOU ARE LOOKING FOR...
2
...YOU WILL ALWAYS FIND YOURSOLUTION AT MITUTOYO.
3
In addition to standard types of small tools,
Mitutoyo also provide their customers with a wide
variety of solutions for special applications.
4
Workpiece Type Picture Application
Tube MicrometerFor measurement of wall thickness.
Tube MicrometerFor measurement of wall thickness.
Tube MicrometerFor measurement of wall thickness.
Tube CaliperFor measurement of wall thickness.
Tube MicrometerFor measuring the inner ring of ball bearings.
Point MicrometerFor measuring the web thickness of drills, small
grooves and keyways.
Point Jaw CaliperInside and outside measurements in hard to
reach places.
Special Micrometer and Caliper
5
Workpiece Type Picture Application
Spline MicrometerFor measuring splined shafts, slots and
keyways.
Sheet Metal MicrometerMeasures thickness of sheet metal.
Sheet Metal MicrometerMeasures thickness of sheet metal.
Blade MicrometerFor measuring the groove diameter of shafts
e.g. for locking rings.
Blade CaliperFor measuring the groove diameter of shafts.
Gear MicrometerMeasures "root tangent length" of spur gears
and helical gears.
Disc MicrometerWith non-rotating spindle for measurement
of soft materials like paper and plastic/rubber parts.
6
Workpiece Type Picture Application
Disc MicrometerWith non-rotating spindle for measurement
of soft materials like paper and plastic/rubber parts.
Crimp Height MicrometerFor measuring the crimp height of a wire-
connector combination.
Gear Tooth MicrometerMeasures the over-pin diameter of gears.
V-Anvil MicrometerMeasures the over-pin diameter of cutting tools
which have three or five flutes.
Screw Thread MicrometerFor measuring the screw pitch diameter.
Wire MicrometerFor measuring of wire thickness.
Constant Force CaliperFor measurment of soft materials.
Special Micrometer and Caliper
7
Workpiece Type Picture Application
Offset CaliperThe beam-mounted jaw can be adjusted to facilitate measurment of stepped sections.
Offset Centerline CaliperFor measuring of hole
center-to-center distances.
Back Jaw Centerline CaliperFor measuring of hole
center-to-center distances.
Point CaliperNarrow tip jaws fit into very small grooves and
tracks.
Knife Edge CaliperFor inside measurements in hard to reach
places.
Find additional product literature and our product catalogue
www.mitutoyo.eu Mitutoyo Europe GmbH
Borsigstraße 8-10 41469 Neuss
Tel. +49 (0) 2137-102-0 Fax +49 (0) 2137-102-351
[email protected] www.mitutoyo.eu
© M
ITUTO
YO/D
11/
14 P
RE14
29
Whatever your challenges are, Mitutoyo supports you from start to finish.
Mitutoyo is not only a manufacturer of top quality measuring products but one that also offers qualified support for the lifetime of the equipment, backed up by comprehensive services that ensure your staff can make the very best use of the investment.
Apart from the basics of calibration and repair, Mitutoyo offers product and metrology training, as well as IT support for the sophisticated software used in modern measuring technology. We can also design, build, test and deliver bespoke measuring solutions and even, if deemed cost-effective, take your critical measurement challenges in-house on a sub-contract basis.
Note: Product illustrations are without obligation. Product descriptions, in particular any and all technical specifications, are only binding when explicitly agreed upon.MITUTOYO and MiCAT are either registered trademarks or trademarks of Mitutoyo Corp. in Japan and/or other countries/regions. Other product, company and brand names mentioned herein are for identification purposes only and may be the trademarks of their respective holders.
Coordinate Measuring Machines
Sensor Systems
Vision Measuring Systems
Test Equipment and Seismometers
Form Measurement
Digital Scale and DRO Systems
Optical Measuring
Small Tool Instruments and Data Management