Datos de grua 5 ton.pdf
Transcript of Datos de grua 5 ton.pdf
SISTEMAS HORMIGA, S.A. de C.V. México, D.F., a 20 de Abril de 2010.
Página No. 5 de 9 Nuestra Referencia: S H G - 4 5 7 3 / 1 0 - A
Proyecto: Hawker Beechcraft
DemagLa marca mundial, líder en movimiento de materiales
www.demagruas-hormiga.com.mx
Item 1) Overhead traveling cranes 2 x 5,0 ton capacity x 29,72m spanD e m a g / H o r m i g a T e c h n i c a l C r a n e D a t a S u m m a r y
Quantity: : 2
Type of crane : Single Girder Overhead Traveling Crane.
Crane model : EKKE
Hoist principal : Demag, model EKDR-Com 5-5,0 - 4/1-10,0 - Z
Capacity of hoist : 5000 Kg
Capacity of the bridge : 5000 Kg
Span : 29,72m
Lifting height : 5,50m
- Lifting speed of hoist principal : two speeds : 5,4 / 0,96 m / minute
Motor model of hoist principal : Demag, model ZBR100 D 12/2
Lifting Motor principal / Power : 6,40 / 0,96 Kw
Classification : Class 1Am according to FEM / similar to CMAA class “D”
The hook has an overload device to protect the whole crane. In case that an overload is detected, the lifting movement is blocked, the operator is only in the position to descend the weight.
Trolley speed : 1.8 - 24 m / minute via inverter
Diameter of trolley wheels : Demag wheels with a diameter of 125 mm.
Wheel material : GGG 70 / nodular cast iron / includes graphite for permanent lubrication of the rail.
Trolley Motor / model : 1 x Demag motor, model ZBA 71B4
Trolley Motor / power : 0.90 KW.
SISTEMAS HORMIGA, S.A. de C.V. México, D.F., a 20 de Abril de 2010.
Página No. 6 de 9 Nuestra Referencia: S H G - 4 5 7 3 / 1 0 - A
Proyecto: Hawker Beechcraft
DemagLa marca mundial, líder en movimiento de materiales
www.demagruas-hormiga.com.mx
Girder Speed : 0.5 - 40 m / minute via inverter
Diameter of wheels / girder : 4 Demag wheels with a diameter of 200 mm
Wheel material : GGG 70 / nodular cast iron / includes graphite for permanent lubrication of the rail.
Gearbox girder : 2 x Demag gearboxes, model AME 30DD
Girder Motor / model : 2 x Demag motors, model ZBA 90 B4
Motor / power : 2 x 1.44 Kw.
Control: The cranes will be operated via a Demag push button station movable along of the
girders. Electrification along of the girder : Flat cable along of 1 of the girders (festoon type).
Voltage of operation : 440 V / 60 Hz / 3 phases
Voltage of control : 110 V
The crane will include an audible and rotating alarm system that will be activated when the crane and/or the trolley movement are activated.
The crane will include limit switches at the ends of the crane girders and of the runway. In this way we guarantee that the crane and / or trolley get into the slowest speed before they
get in contact with the buffers.
Dead weight of the crane : 8,912 Kg aprox. Maximum wheel load on the runway : 4,836 Kg aprox.
2 x set of electrification along the bay for a length of 168m and for 440 V / 60 Hz / 3Fases. We are considering that the customer will submit for this electrical feeding 1 power supply line at the altitude of the runway and located at the middle of the runway.
The electrical feeding system includes all accessories to guaranty the correct operation of the crane.