DATA SHEET AAT116052ebad10ee97eea25d5e-d7d40819259e7d3022d9ad53e3694148.r84.cf3.rackcdn.co…Power...
Transcript of DATA SHEET AAT116052ebad10ee97eea25d5e-d7d40819259e7d3022d9ad53e3694148.r84.cf3.rackcdn.co…Power...
1
AAT116012V, 3A Step-Down DC/DC Converter
DATA SHEET
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 201996A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • May 28, 2012
General DescriptionThe AAT1160 is an 800kHz high efficiency step-down DC/DC converter. With a wide input voltage range of 4.0V to 13.2V, the AAT1160 is an ideal choice for dual-cell Lithium-ion battery-powered devices and mid-pow-er-range regulated 12V-powered industrial applications. The internal power switches are capable of delivering up to 3A to the load.
The AAT1160 is a highly integrated device, simplifying system-level design. Minimum external components are required for the converter.
The AAT1160 optimizes efficiency throughout the entire load range. It operates in a combination PWM/Light Load mode for improved light-load efficiency. It can also operate in a forced Pulse Width Modulation (PWM) mode for easy control of the switching noise as well as faster transient response. The high switching frequency allows the use of small external components. The low current shutdown feature disconnects the load from VIN and drops shutdown current to less than 1μA.
The AAT1160 is available in a Pb-free, space-saving, thermally-enhanced 16-pin TDFN34 package and is rated over an operating temperature range of -40°C to +85°C.
Features• Input Voltage Range: 4.0V to 13.2V• Up to 3A Load Current • Fixed or Adjustable Output:▪ Output Voltage: 0.6V to VIN
• Low 150μA No-Load Operating Current• Less than 1μA Shutdown Current• Up to 96% Efficiency• Integrated Power Switches• 800kHz Switching Frequency▪ Synchronizable to External Clock▪ Forced PWM or Light Load Mode
• Soft Start Function• Short-Circuit and Over-Temperature Protection• Minimum External Components• TDFN34-16 Package• Temperature Range: -40°C to +85°C
Applications• Distributed Power Systems• Industrial Applications • Laptop Computers• Portable DVD Players• Portable Media Players• Set-Top Boxes• TFT LCD Monitors and HDTVs
Typical Application
LXIN
AIN AAT1160
EN
PGND
FB
AGNDLDO
COMP
SYNC
C3, C42x22μF
R3432k
R659k
L
2.2 to 3.8μH
Output:0.94 x Input max
C622μF
C81μF
C91μF
C7150pF
C20.1μF
R410
R550k
Input:4.0V ~ 13.2V
DGND
2
AAT116012V, 3A Step-Down DC/DC Converter
DATA SHEET
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 201996A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • May 28, 2012
Pin Descriptions
Pin # Symbol Function
1, 2, EP2 LXPower switching node. LX is the drain of the internal P-channel switch and N-channel synchronous recti-fi er. Connect the output inductor to the two LX pins and to EP2. A large exposed copper pad under the package should be used for EP2.
3, 12 N/C Not connected.
4, 5 INPower source input. Connect IN to the input power source. Bypass IN to DGND with a 10μF or greater capacitor. Connect both IN pins together as close to the IC as possible. An additional 100nF ceramic ca-pacitor should also be connected between the two IN pins and DGND, pin 6
6, 13, EP1 DGNDExposed Pad 1 Digital Ground, DGND. The exposed thermal pad (EP1) should be connected to board ground plane and pins 6 and 13. The ground plane should include a large exposed copper pad under the package for thermal dissipation (see package outline).
7 AINInternal analog bias input. AIN supplies internal power to the AAT1160. Connect AIN to the input source voltage and bypass to AGND with a 0.1μF or greater capacitor. For additional noise rejection, connect to the input power source through a 10 or lower value resistor.
8 LDOInternal LDO bypass node. The output voltage of the internal LDO is bypassed at LDO. The internal cir-cuitry of the AAT1160 is powered from LDO. Do not draw external power from LDO. Bypass LDO to AGND with a 1μF or greater capacitor.
9 FBOutput voltage feedback input. FB senses the output voltage for regulation control. For fi xed output versions, connect FB to the output voltage. For adjustable versions, drive FB from the output voltage through a resistive voltage divider. The FB regulation threshold is 0.6V.
10 COMP Control compensation node. Connect a series RC network from COMP to AGND, R = 50k and C = 150pF.11 AGND Analog signal ground. Connect AGND to PGND at a single point as close to the IC as possible.
14 SYNC
Frequency select and synchronization input. Drive SYNC with a 500kHz to 1.6MHz signal to synchronize the AAT1160 switching frequency to that signal. The Sync pin is also a mode select input. Drive SYNC high or connect to the LDO pin for low-noise forced PWM mode. Drive SYNC low for high-effi ciency PWM/Light Load mode.
15 ENActive high enable input. Drive EN high to turn on the AAT1160; drive it low to turn it off. For automatic startup, connect EN to IN through a 4.7k resistor. EN must be biased high, biased low, or driven to a logic level by an external source. Do not let the EN pin fl oat when the device is powered.
16 PGND Power ground. Connect AGND to PGND at a single point as close to the IC as possible.
Pin Configuration
TDFN34-16(Top View)
N/C
IN
IN
LX
LX
3
DGND
AIN
LDO
SYNC
DGND
N/C
PGND
EN
AGND
COMP
FB
4
5
1
2
6
7
8
14
13
12
16
15
11
10
9
EP2
EP1
3
AAT116012V, 3A Step-Down DC/DC Converter
DATA SHEET
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 201996A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • May 28, 2012
Absolute Maximum Ratings1
Symbol Description Value UnitsVIN, VAIN Input Voltage -0.3 to 14 V
VLX LX to GND Voltage -0.3 to VIN + 0.3 VVFB FB to GND Voltage -0.3 to VIN + 0.3 VVEN EN to GND Voltage -0.3 to VIN + 0.3 V
VSYNC SYNC to GND Voltage -0.3 to 6.5 VTJ Operating Junction Temperature Range -40 to 150 °C
Thermal Information2
Symbol Description Value UnitsPD Maximum Power Dissipation3 2.7 WJA Thermal Resistance 37 °C/W
1. Stresses above those listed in Absolute Maximum Ratings may cause permanent damage to the device. Functional operation at conditions other than the operating conditions specified is not implied. Only one Absolute Maximum Rating should be applied at any one time.
2. Mounted on an FR4 board.3. Derate 2.7mW/°C above 25°C.
4
AAT116012V, 3A Step-Down DC/DC Converter
DATA SHEET
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 201996A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • May 28, 2012
Electrical Characteristics1
4.0V < VIN < 13.2V. CIN = COUT = 22μF; L = 2.2μH or 3.8μH, TA = -40°C to +85°C, unless otherwise noted. Typical values are at TA = 25°C.
Symbol Description Conditions Min Typ Max UnitsVIN Input Voltage Range 4.0 13.2 V
VUVLO Input Under-Voltage LockoutRising 4.3
VHysteresis 0.3
IQ Supply Current No Load 150 300 μAISHDN Shutdown Current VEN = GND 1 μA
VOUT Output Voltage Range 0.6 0.94 VIN
V
VOUT Output Voltage Accuracy IOUT = 0A to 3A -2.5 2.5 %VLINEREG/
VINLine Regulation VIN = 4.5V to 13.2V 0.023 0.100 %/V
VLOADREG Load Regulation VIN = 12V, VOUT = 5V, IOUT = 0A to 3A 0.4 %
VFBFeedback Reference Voltage (adjustable version) No Load, TA = 25°C 0.59 0.60 0.61 V
IFBLEAK FB Leakage Current VOUT = 1.2V Adjustable Version 0.2
μAFixed Version 2
FOSC PWM Oscillator Frequency 0.6 0.8 1 MHzFSYNC External Clock Frequency Range CMOS Logic Clock Signal on SYNC Pin 0.5 1.6 MHzTS Start-Up Time IOUT = 3A, VOUT = 5V 2 ms
Foldback Frequency 200 kHzDC Maximum Duty Cycle 94 %TON Minimum Turn-On Time 100 nsTSS Soft-Start Time 2 ms
RDS(ON)H P-Channel On ResistanceVIN = 12V 0.12
VIN = 6V 0.15
RDS(ON)L N-Channel On ResistanceVIN = 12V 0.06
VIN = 6V 0.08
Effi ciency VIN = 12V, VOUT = 5V, IOUT = 3A 90 %ILIM PMOS Current Limit 4.0 6.0 A
ILXLEAK LX Leakage Current VIN = 13.2V, VLX = 0 to VIN 1 μATSD Over-Temperature Shutdown Threshold 140 °CTHYS Over-Temperature Shutdown Hysteresis 25 °CVILEN EN Logic Low Input Threshold 0.4 VVIHEN EN Logic High Input Threshold 1.4 VVILSYNC SYNC Logic Low Input Threshold 0.4 VVIHSYNC SYNC Logic High Input Threshold 1.62 V
IEN EN Input Current VEN = 0V, VEN = 13.2V -1.0 1.0 μA
1. The AAT1160 is guaranteed to meet performance specifications over the -40°C to +85°C operating temperature range and is assured by design, characterization, and correla-tion with statistical process controls.
5
AAT116012V, 3A Step-Down DC/DC Converter
DATA SHEET
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 201996A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • May 28, 2012
Typical Characteristics
Efficiency vs. Load Current(VOUT = 5V)
Output Current (A)
Eff
icie
nc
y (
%)
0
10
20
30
40
50
60
70
80
90
100
0.0001 0.001 0.01 0.1 1 10
12V6V
8.4V 10V
13.2V
Load Regulation(VOUT = 5V)
Output Current (A)
Ou
tpu
t V
olt
ag
e D
iffe
ren
ce (
%)
-0.5
-0.4
-0.3
-0.2
-0.1
0
0.1
0.2
0.3
0.4
0.5
0.0001 0.001 0.01 0.1 1 10
13.2V
10V
8.4V
6V
12V
Efficiency vs. Load Current(VOUT = 5V; PWM Mode)
Output Current (A)
Eff
icie
nc
y (
%)
0
10
20
30
40
50
60
70
80
90
100
0.0001 0.001 0.01 0.1 1 10
6V
8.4V
10V 13.2V
12V
Load Regulation(VOUT = 5V; PWM Mode)
Output Current (A)
Ou
tpu
t V
olt
ag
e D
iffe
ren
ce (
%)
-0.5
-0.4
-0.3
-0.2
-0.1
0
0.1
0.2
0.3
0.4
0.5
0.0001 0.001 0.01 0.1 1 10
6V
8.4V
10V
13.2V
12V
Efficiency vs. Load Current(VOUT = 3.3V)
Output Current (A)
Eff
icie
nc
y (
%)
0
10
20
30
40
50
60
70
80
90
100
0.0001 0.001 0.01 0.1 1 10
5V
10V
8.4V
12V 13.2V
Load Regulation(VOUT = 3.3V)
Output Current (mA)
Ou
tpu
t V
olt
ag
e D
iffe
ren
ce (
%)
-0.6
-0.4
-0.2
0.0
0.2
0.4
0.6
1 10 100 1000 10000
10V
12V
13.2V5V
8.4V
6
AAT116012V, 3A Step-Down DC/DC Converter
DATA SHEET
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 201996A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • May 28, 2012
Typical Characteristics
Efficiency vs. Load Current(VOUT = 3.3V; PWM Mode)
Output Current (A)
Eff
icie
nc
y (
%)
0
10
20
30
40
50
60
70
80
90
100
1 10 100 1000 10000
13.2V12V
8.4V
10V
5V
Load Regulation(VOUT = 3.3V; PWM Mode)
Output Current (mA)
Ou
tpu
t V
olt
ag
e D
iffe
ren
ce (
%)
-0.6
-0.4
-0.2
0.0
0.2
0.4
0.6
1 10 100 1000 10000
5V
12V
13.2V
10V 8.4V
Line Regulation(VOUT = 5V)
Input Voltage (V)
Ou
tpu
t V
olt
ag
e D
iffe
ren
ce (
%)
-0.5
-0.3
-0.1
0.1
0.3
0.5
6 7 8 9 10 11 12
3A
1.5A100mA
1mA
10mA
Line Regulation(VOUT = 3.3V)
Input Voltage (V)
Ou
tpu
t V
olt
ag
e D
iffe
ren
ce (
%)
-0.04
-0.03
-0.02
-0.01
0
0.01
0.02
0.03
0.04
0.05
5 6 7 8 9 10 11 12
1.5A
10mA3A
1mA
100mA
Switching Current vs. Input Voltage(VOUT = 5V)
Input Voltage (V)
Cu
rre
nt
(µA
)
110
120
130
140
150
160
170
6 7 8 9 10 11 12
-40°C
25°C
85°C
Switching Current vs. Temperature
Temperature (°C)
Cu
rre
nt
(µA
)
110
120
130
140
150
160
170
-40 -15 10 35 60 85
85°C
-40°C
7
AAT116012V, 3A Step-Down DC/DC Converter
DATA SHEET
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 201996A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • May 28, 2012
Typical Characteristics
N-Channel RDS(ON) vs. Temperature
Temperature (°C)
Re
sis
tan
ce
(m
ΩΩ)
0
20
40
60
80
100
120
-40 -15 10 35 60 85
12V
6V
P-Channel RDS(ON) vs. Temperature(VIN = 6V)
Temperature (°C)
Re
sis
tan
ce
(m
ΩΩ)
0
20
40
60
80
100
120
140
160
180
200
-40 -15 10 35 60 85
12V
6V
Switching Frequency vs. Temperature
Temperature (°C)
Sw
itch
ing
Fre
qu
en
cy (
Hz)
770
775
780
785
790
795
800
805
810
-40 -15 10 35 60 85
12V
6V
Line Transient(VOUT = 5.0V; CFF = 100pF; VIN = 7.6V to 11V;
IOUT = 3A; CIN = 10µF; COUT = 22µF; L = 3.8µH)
Time (100µs/div)
Inp
ut
Vo
lta
ge
(to
p)
(V)
Ou
tpu
t Cu
rren
t (bo
ttom
) (A)4
5
6
7
8
9
10
11
12
4.90
4.95
5.00
5.05
5.10
5.15
5.20
5.25
5.30
Start-Up Time(VOUT = 5.0V; CFF = 100pF; RLOAD = 1.67ΩΩ;
CIN = 10µF; COUT = 22µF; L = 3.8µH)
Time (500µs/div)
En
ab
le V
olt
ag
e (
top
) (V
)
Inp
ut C
urre
nt (b
otto
m) (A
)0
1
2
3
4
5
6
0
1
2
3
4
5
6
VEN
VOUT
ILOAD
Load Transient(VOUT = 5.0V; CFF = 100pF; IOUT = 1A to 3A;
CIN = 10µF; COUT = 22µF; L = 3.8µH)
Time (100µs/div)
Ou
tpu
t V
olt
ag
e (
top
) (V
)
Lo
ad
an
d In
du
cto
r Cu
rren
t
(bo
ttom
) (A)
3
3.5
4
4.5
5
5.5
1
2
3
4
5
6
7
8
9
ILX
ILOAD
8
AAT116012V, 3A Step-Down DC/DC Converter
DATA SHEET
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 201996A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • May 28, 2012
Typical Characteristics
Load Transient(VOUT = 5.0V; CFF = 100pF; IOUT = 10mA to 3A;
CIN = 10µF; COUT = 22µF; L = 3.8µH)
Time (100µs/div)
Ou
tpu
t V
olt
ag
e (
top
) (V
)
Lo
ad
an
d In
du
cto
r Cu
rren
t
(bo
ttom
) (A)
0
1
2
3
4
5
6
0
1
2
3
4
5
6
ILOAD
ILX
SYNC Mode(VOUT = 5.0V; CFF = 100pF; SYNC = 1.4MHz;
IOUT = 3A; CIN = 10µF; COUT = 22µF; L = 3.8µH)
Time (200ns/div)
SY
NC
(to
p)
(V) L
X (b
otto
m) (V
)
0
2
4
6
8
0
10
20
30
40
SYNC Mode(VOUT = 5.0V; CFF = 100pF; SYNC = 500kHz;
IOUT = 3A; CIN = 10µF; COUT = 2x22µF; L = 3.8µH)
Time (500ns/div)
SY
NC
(to
p)
(V) L
X (b
otto
m) (V
)
0
2
4
6
8
0
10
20
30
40
VOUT vs. Temperature(VOUT = 3.3V; ILOAD = 1.5A)
Temperature (°C)
Ou
tpu
t V
olt
ag
e D
iffe
ren
ce (
%)
-0.8
-0.6
-0.4
-0.2
0
0.2
0.4
0.6
0.8
1
-40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90
9
AAT116012V, 3A Step-Down DC/DC Converter
DATA SHEET
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 201996A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • May 28, 2012
Functional DescriptionThe AAT1160 is a current-mode step-down DC/DC con-verter that operates over a wide 4V to 13.2V input volt-age range and is capable of supplying up to 3A to the load with the output voltage regulated as low as 0.6V. Both the P-channel power switch and N-channel syn-chronous rectifier are internal, reducing the number of external components required. The output voltage is adjusted by an external resistor divider; fixed output voltage versions are available upon request. The regula-tion system is externally compensated, allowing the circuit to be optimized for each application. The AAT1160 includes cycle-by-cycle current limiting, frequency fold-back for improved short-circuit performance, and ther-mal overload protection to prevent damage in the event of an external fault condition.
Control LoopThe AAT1160 regulates the output voltage using con-stant frequency current mode control. The AAT1160 monitors current through the high-side P-channel MOSFET and uses that signal to regulate the output volt-age. This provides improved transient response and eases compensation. Internal slope compensation is included to ensure the current “inside loop” stability.
High efficiency is maintained under light load conditions by automatically switching to variable frequency Light Load control. In this condition, transition losses are reduced by operating at a lower frequency at light loads.
Functional Block Diagram
ControlLogic
+
-
LDO
+
-
Reference
Note 1FB
EN
SYNC
AGND
DGND
PGND
LX
INAINLDO
COMP
Note 1: For fixed output voltage versions, FB is connected to the error amplifier through the resistive voltage divider shown.
.
Internal Power
+
-
Current Sense Amp
ErrorAmp Current
Mode Comparator
10
AAT116012V, 3A Step-Down DC/DC Converter
DATA SHEET
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 201996A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • May 28, 2012
Short-Circuit ProtectionThe AAT1160 uses a cycle-by-cycle current limit to pro-tect itself and the load from an external fault condition. When the inductor current reaches the internally set 6.0A current limit, the P-channel MOSFET switch turns off and the N-channel synchronous rectifier is turned on, limiting the inductor and the load current.
During an overload condition, when the output voltage drops below 25% of the regulation voltage (0.15V at FB), the AAT1160 switching frequency drops by a factor of 4. This gives the inductor current ample time to reset during the off time to prevent the inductor current from rising uncontrolled in a short-circuit condition.
Thermal ProtectionThe AAT1160 includes thermal protection that disables the regulator when the die temperature reaches 140ºC. It automatically restarts when the temperature decreas-es by 25ºC or more.
Frequency SynchronizationThe AAT1160 operates at a fixed 800kHz switching fre-quency, or it can be synchronized to an external signal. Synchronize switching to an external signal between 500kHz and 1.6MHz by driving SYNC with that signal. In this mode, the rising edge of the signal at SYNC turns on the P-channel switch. When changing switching frequen-cy, the external components CIN, COUT and L must be changed according to the component equations. The external clock duty cycle is limited to a 30% to 90% range.
PWM or Light Load ModeThe device can be set to operate in forced Pulse Width Modulation (PWM) mode to filter or set the switching noise to a desired frequency by connecting the SYNC to a high logic level. Alternately, a combination PWM/LL (Light Load) mode for improved light load efficiency can be set by connecting the SYNC pin to GND or a low logic level. When connecting SYNC to an external clock sig-nal, the device is always in forced PWM mode.
Applications Information
Setting the Output VoltageFigure 1 shows the basic application circuit for the AAT1160 and output setting resistors. Resistors R3 and R6 program the output to regulate at a voltage higher than 0.6V. To limit the bias current required for the external feedback resistor string while maintaining good noise immunity, the minimum suggested value for R6 is 5.9kΩ. Although a larger value will further reduce quies-cent current, it will also increase the impedance of the feedback node, making it more sensitive to external noise and interference. Table 1 summarizes the resistor values for various output voltages with R6 set to either 5.9kΩ for good noise immunity or 59kΩ for reduced no load input current.
PGND
AGND
LX
LX
IN
IN
EN
DGND
FBAAT1160C6
22μF
VIN 4.5V-13.2V L1
3.8μH
C1100pF
C3, C42x22μFR3
43.2kΩ
R65.9kΩ
VOUT5V, 2A
5
4
6
9
2
1
11
10AIN7
DGND
LDO
SYNC
COMP
LX
DGND
R550kΩ
C7150pFC9
1μF
C20.1μF
R410Ω
148
13
15
16
EP1
EP2
C81μF
Figure 1: Typical Application Circuit.
The adjustable feedback resistors, combined with an external feed forward capacitor (C1 in Figure 1), deliver enhanced transient response for extreme pulsed load applications. The addition of the feed forward capacitor typically requires a larger output capacitor C3/C4 for stability. Larger C3/C4 values reduce overshoot and undershoot during startup and load changes. However, do not exceed 470pF to maintain stable operation.
The external resistors set the output voltage according to the following equation:
⎛ ⎞ VOUT = 0.6V 1 + ⎝ ⎠
R3
R6
or⎛ ⎞⎝ ⎠R3 = -1 · R6VOUT
VREF
11
AAT116012V, 3A Step-Down DC/DC Converter
DATA SHEET
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 201996A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • May 28, 2012
Table 1 shows the resistor selection for different output voltage settings.
VOUT (V)R6 = 5.9kΩ
R3 (kΩ)R6 = 59kΩ
R3 (kΩ)0.8 1.96 19.60.9 2.94 29.41.0 3.92 39.21.1 4.99 49.91.2 5.90 59.01.3 6.81 68.11.4 7.87 78.71.5 8.87 88.71.8 11.8 1181.85 12.4 1242.0 13.7 1372.5 18.7 1873.3 26.7 2675.0 43.2 432
Table 1: Resistor Selection for Different Output Voltage Settings. Standard 1% Resistors are
Substituted for Calculated Values.
Inductor SelectionFor most designs, the AAT1160 operates with inductors of 2μH to 4.7μH. Low inductance values are physically smaller, but require faster switching, which results in some efficiency loss. The inductor value can be derived from the following equation:
VOUT · (VIN - VOUT)
VIN · ΔIL · FOSC
L1 =
Where ∆IL is inductor ripple current. Large value induc-tors lower ripple current and small value inductors result in high ripple currents. Choose inductor ripple current approximately 32% of the maximum load current 3A, or ∆IL = 959mA. For output voltages above 3.3V, the mini-
mum recommended inductor is 3.8μH. For 3.3V and below, use a 2 to 2.2μH inductor. For optimum voltage-positioning load transients, choose an inductor with DC series resistance in the 15mΩ to 20mΩ range. For higher efficiency at heavy loads (above 1A), or minimal load regulation (but some transient overshoot), the resistance should be kept below 18mΩ. The DC current rating of the inductor should be at least equal to the maximum load current plus half the ripple current to prevent core saturation (3A + 526mA). Table 2 lists some typical surface mount inductors that meet target applications for the AAT1160.
Manufacturer’s specifications list both the inductor DC current rating, which is a thermal limitation, and the peak current rating, which is determined by the satura-tion characteristics. The inductor should not show any appreciable saturation under normal load conditions. Some inductors may meet the peak and average current ratings yet result in excessive losses due to a high DCR. Always consider the losses associated with the DCR and its effect on the total converter efficiency when selecting an inductor. For example, the 3.7μH CDR7D43 series inductor selected from Sumida has an 18.9mΩ DCR and a 4.3ADC current rating. At full load, the inductor DC loss is 170mW which gives only a 1.13% loss in effi-ciency for a 3A, 5V output.
Input Capacitor SelectionThe input capacitor reduces the surge current drawn from the input and switching noise from the device. The input capacitor impedance at the switching frequency shall be less than the input source impedance to prevent high frequency switching current passing to the input. A low ESR input capacitor sized for maximum RMS current must be used. Ceramic capacitors with X5R or X7R dielectrics are highly recommended because of their low ESR and small temperature coefficients. A 22μF ceramic capacitor is sufficient for most applications.
Manufacturer Part Number L (μH)Max DCR
(mΩ)Rated DC
Current (A)Size WxLxH
(mm)Sumida CDRH103RNP-2R2N 2.2 16.9 5.10 10.3x10.5x3.1Sumida CDR7D43MNNP-3R7NC 3.7 18.9 4.3 7.6x7.6x4.5Coilcraft MSS1038-382NL 3.8 13 4.25 10.2x7.7x3.8
Table 2: Typical Surface Mount Inductors.
12
AAT116012V, 3A Step-Down DC/DC Converter
DATA SHEET
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 201996A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • May 28, 2012
To estimate the required input capacitor size, determine the acceptable input ripple level (VPP) and solve for C. The calculated value varies with input voltage and is a maximum when VIN is double the output voltage.
⎛ ⎞ · 1 - ⎝ ⎠
VO
VIN
CIN =
VO
VIN
⎛ ⎞ - ESR · FOSC⎝ ⎠
VPP
IO
⎛ ⎞ · 1 - = for VIN = 2 · VO⎝ ⎠
VO
VIN
VO
VIN
1
4
CIN(MIN) =
1
⎛ ⎞ - ESR · 4 · FOSC⎝ ⎠
VPP
IO
Always examine the ceramic capacitor DC voltage coef-ficient characteristics when selecting the proper value. For example, the capacitance of a 10μF, 16V, X5R ceram-ic capacitor with 12V DC applied is actually about 8.5μF.
The maximum input capacitor RMS current is:
⎛ ⎞IRMS = IO · · 1 - ⎝ ⎠
VO
VIN
VO
VIN
The input capacitor RMS ripple current varies with the input and output voltage and will always be less than or equal to half of the total DC load current:
⎛ ⎞· 1 - = D · (1 - D) = 0.52 =
⎝ ⎠VO
VIN
VO
VIN
1
2
for VIN = 2 · VO
IO
RMS(MAX)I
2=
The term ⎛ ⎞
· 1 - ⎝ ⎠VO
VIN
VO
VIN appears in both the input voltage ripple and input capacitor RMS current equations and is at maximum when VO is twice VIN. This is why the input voltage ripple and the input capacitor RMS current ripple are a maximum at 50% duty cycle. The input capacitor provides a low impedance loop for the edges of pulsed current drawn by the AAT1160. Low ESR/ESL X7R and X5R ceramic capacitors are ideal for this function. To minimize stray inductance, the capacitor should be placed as closely as possible to the IC. This keeps the
high frequency content of the input current localized, minimizing EMI and input voltage ripple. The proper placement of the input capacitor (C6) can be seen in the evaluation board layout in Figure 3. Additional noise fil-tering for proper operation is accomplished by adding a small 0.1μF capacitor on the IN pins (C2).
A laboratory test set-up typically consists of two long wires running from the bench power supply to the evalu-ation board input voltage pins. The inductance of these wires, along with the low-ESR ceramic input capacitor, can create a high Q network that may affect converter performance. This problem often becomes apparent in the form of excessive ringing in the output voltage dur-ing load transients. Errors in the loop phase and gain measurements can also result. Since the inductance of a short PCB trace feeding the input voltage is significantly lower than the power leads from the bench power sup-ply, most applications do not exhibit this problem. In applications where the input power source lead induc-tance cannot be reduced to a level that does not affect the converter performance, a high ESR tantalum or alu-minum electrolytic should be placed in parallel with the low ESR, ESL bypass ceramic. This dampens the high Q network and stabilizes the system.
Output Capacitor SelectionThe output capacitor is required to keep the output volt-age ripple small and to ensure regulation loop stability. The output capacitor must have low impedance at the switching frequency. Ceramic capacitors with X5R or X7R dielectrics are recommended due to their low ESR and high ripple current. The output ripple VOUT is determined by:
⎛ ⎞ · ESR +ΔVOUT ≤ ⎝ ⎠
VOUT · (VIN - VOUT)
VIN · FOSC · L
1
8 · FOSC · COUT
The output capacitor limits the output ripple and pro-vides holdup during large load transitions. A 10μF to 47μF X5R or X7R ceramic capacitor typically provides sufficient bulk capacitance to stabilize the output during large load transitions and has the ESR and ESL charac-teristics necessary for low output ripple. The output volt-age droop due to a load transient is dominated by the capacitance of the ceramic output capacitor. During a step increase in load current, the ceramic output capac-itor alone supplies the load current until the loop responds. Within two or three switching cycles, the loop responds and the inductor current increases to match
13
AAT116012V, 3A Step-Down DC/DC Converter
DATA SHEET
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 201996A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • May 28, 2012
the load current demand. The relationship of the output voltage droop during the three switching cycles to the output capacitance can be estimated by:
COUT = 3 · ΔILOAD
VDROOP · FOSC
Once the average inductor current increases to the DC load level, the output voltage recovers. The above equa-tion establishes a limit on the minimum value for the output capacitor with respect to load transients. The internal voltage loop compensation also limits the mini-mum output capacitor value to 22μF. This is due to its effect on the loop crossover frequency (bandwidth), phase margin, and gain margin. Increased output capac-itance will reduce the crossover frequency with greater phase margin.
The maximum output capacitor RMS ripple current is given by:
1
2 3
VOUT · (VIN(MAX) - VOUT)RMS(MAX)I
L · FOSC · VIN(MAX)
= ··
Dissipation due to the RMS current in the ceramic output capacitor ESR is typically minimal, resulting in less than a few degrees rise in hot-spot temperature.
CompensationThe AAT1160 step-down converter uses peak current mode control with slope compensation scheme to main-tain stability with lower value inductors for duty cycles greater than 50%. The regulation feedback loop in the IC is stabilized by the components connected to the COMP pin, as shown in Figure 1.
To optimize the compensation components, the following equations can be used. The compensation resistor RCOMP (R5) is calculated using the following equation:
2πVOUT · COUT · FOSC
10GEA · GCOMP · VFB
RCOMP (R5)=
Where VFB = 0.6V, GCOMP = 40.1734 and GEA = 9.091 · 10-5.
FOSC is the switching frequency and COUT is based on the output capacitor calculation. The CCOMP value can be determined from the following equation:
CCOMP (C7) =
4
⎛ ⎞ 2πRCOMP (R5) · ⎝ ⎠
FOSC
10
Layout GuidanceFigure 2 is the schematic for the evaluation board. When laying out the PC board, the following layout guideline should be followed to ensure proper operation of the AAT1160:
1. Exposed pad EP1 must be reliably soldered to PGND/DGND/AGND. The exposed thermal pad should be connected to board ground plane and pins 6, 11, 13, and 16. The ground plane should include a large exposed copper pad under the package for thermal dissipation.
2. The power traces, including GND traces, the LX traces and the VIN trace should be kept short, direct and wide to allow large current flow. The L1 connec-tion to the LX pins should be as short as possible. Use several via pads when routing between layers.
3. Exposed pad pin EP2 must be reliably soldered to the LX pins 1 and 2. The exposed thermal pad should be connected to the board LX connection and the inductor L1 and also pins 1 and 2. The LX plane should include a large exposed copper pad under the package for thermal dissipation.
4. The input capacitors (C2 and C6) should be con-nected as close as possible to IN (Pins 4 and 5) and DGND (Pin 6) to get good power filtering.
5. Keep the switching node LX away from the sensitive FB node.
6. The feedback trace for the FB pin should be separate from any power trace and connected as closely as possible to the load point. Sensing along a high-current load trace will degrade DC load regulation. The feedback resistors should be placed as close as possible to the FB pin (Pin 9) to minimize the length of the high impedance feedback trace.
7. The output capacitors C3, 4, and 5 and L1 should be connected as close as possible and there should not be any signal lines under the inductor.
8. The resistance of the trace from the load return to the PGND (Pin 16) should be kept to a minimum. This will help to minimize any error in DC regulation due to differences in the potential of the internal signal ground and the power ground.
14
AAT116012V, 3A Step-Down DC/DC Converter
DATA SHEET
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 201996A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • May 28, 2012
VINVOUT
IN5
AIN7
PGND16 LDO 8
LX 2
N/C3
N/C 12
IN4
DGND13
FB 9
EN15
SYNC 14
AGND 11
LX 1
COMP 10
DGND6
U1 AAT1160
DGND
*Note: Connect GND, DGND, and AGND at ICInductor -Sumida CDRH103RNP-3R3NC-B
R1
4.75K
R2
4.75K
R410
C81μF
C20.1μF
C91μF
R550K
C7150pF
C1100pF
R3432K
R659K
C322μF
C422μF
C5NPC6
10μF
JP1Enable
JP2SYNC
TP3Enable
TP2LX
TP4VOUT
TP6VOUT
TP8GND
TP12GND
TP10
SYNCTP11GND
TB2VOUTTB1
VIN
L1
3.8μH
*
TP14GND
TP1GND
TP5VIN
TP7VIN
TP9GND
TP13GND
DGND
DGNDEP1
EP2
LX
Figure 2: AAT1160 Evaluation Board Schematic.
Figure 3: AAT1160 Evaluation Board Figure 4: AAT1160 Evaluation Board Component Side Layout. Solder Side Layout.
15
AAT116012V, 3A Step-Down DC/DC Converter
DATA SHEET
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 201996A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • May 28, 2012
Design Example
SpecificationsVOUT 5V @ 3A, Pulsed Load ILOAD = 3AVIN 12V nominalFOSC 800kHzTAMB 85°C in TDFN34-16 Package
Output Inductor
VOUT · (VIN - VOUT)
VIN · ΔIL · FOSC
L1 = = 3.8µH; see Table 2.
ΔIL = 0.32 · ILOAD
For Coilcraft inductor MSS1038 3.8μH DCR = 13m max.
VOUT VO1 5V 5V ΔI1 = ⋅ 1 - = ⋅ 1 - = 959mAL1 ⋅ FOSC VIN 3.8µH ⋅ 800kHz 12V
IPK1 = ILOAD + ΔI1
= 3A + 0.479A = 3.48A2
PL1 = ILOAD
2 ⋅ DCR = 3A
2 ⋅ 13mΩ = 117mW
⎛⎝
⎞⎠
⎛⎝
⎞⎠
Output Capacitor VDROOP = 0.2V
1
2 3
1 5V · (12V - 5V)
3.8µH · 800kHz · 12V 2 3RMS(MAX)I
L · FOSC · VIN(MAX)
= · ·
3 · ΔILOAD
VDROOP · FOSC
3 · 3A
0.2V · 800kHzCOUT = = = 56µF; use two 22µF
· = 277mArms·
(VOUT) · (VIN(MAX) - VOUT)=
Pesr = esr · IRMS2 = 5mΩ · (277mA)2 = 384µW
Input CapacitorInput Ripple VPP = 50mV
CIN = = = 26µF; use 22µF
1
⎛ ⎞- ESR · 4 · FOSC⎝ ⎠
VPP
ILOAD
1
⎛ ⎞ - 5mΩ · 4 · 800kHz
⎝ ⎠50mV
3A
ILOAD
RMS(MAX)I
P = esr · IRMS
2 = 5mΩ · (1.5A)
2 = 11.25mW
2= = 1.5Arms
16
AAT116012V, 3A Step-Down DC/DC Converter
DATA SHEET
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 201996A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • May 28, 2012
AAT1160 LossesTotal losses can be estimated by calculating the dropout (VIN = VO) losses where the power MOSFET RDS(ON) will be at the maximum value. All values assume an 85°C ambient temperature and a 140°C junction temperature with the TDFN 37°C/W package.
PLOSS = ILOAD
2 · RDS(ON)H = 3A
2 · 0.12Ω = 1.08W
TJ(MAX) = TAMB + ΘJA · PLOSS = 85°C + (37°C/W) · 1.08W = 125°C
The total losses are also investigated at the nominal input voltage (12V). The simplified version of the RDS(ON) losses assumes that the N-channel and P-channel RDS(ON) are equal.
PTOTAL = ILOAD
2 · RDS(ON) + [(tsw · FOSC · ILOAD + IQ) · VIN]
= 3A2 · 100mΩ + [(5ns · 800kHz · 3A + 150µA) · 12V] = 1.0458W
TJ(MAX) = TAMB + ΘJA · PLOSS = 85°C + (37°C/W) · 1.0458W = 124°C
17
AAT116012V, 3A Step-Down DC/DC Converter
DATA SHEET
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 201996A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • May 28, 2012
Copyright © 2012 Skyworks Solutions, Inc. All Rights Reserved.
Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the information contained herein. Sky-works may change its documentation, products, services, specifi cations or product descriptions at any time, without notice. Skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoever for confl icts, incompatibilities, or other diffi culties arising from any future changes.
No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or information provided here-under, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions of Sale.
THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, IN-CLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury, death, physical or en-vironmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale.
Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifi cations as a result of design defects, errors, or operation of products outside of pub-lished parameters or design specifi cations. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifi cations or parameters.
Skyworks, the Skyworks symbol, and “Breakthrough Simplicity” are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands and names are for identifi cation purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com, are incorporated by reference.
Ordering Information
Package Marking1 Part Number (Tape and Reel)2
TDFN34-16 XAXYY AAT1160IRN-0.6-T13
Skyworks Green™ products are compliant with all applicable legislation and are halogen-free.For additional information, refer to Skyworks Definition of Green™, document number SQ04-0074.
Package InformationTDFN34-164
Top View Bottom View
Side View
3.000 ± 0.050
4.00
0 ±
0.05
0Index Area
R0.15 (REF)Pin 1 ID
1.600 ± 0.050
1.600 ± 0.050
0.430 ± 0.0500.25 REF
0.35
RE
F
2.35
0 ±
0.05
00.
700
± 0.
050
0 + 0.100-0.000 0.230 ± 0.050
0.75
0 ±
0.05
0
0.23
0 ±
0.05
0
0.45
0 ±
0.05
0
All dimensions in millimeters.
1. XYY = assembly and date code.2. Sample stock is generally held on part numbers listed in BOLD. 3. Available exclusively outside of the United States and its territories.4. The leadless package family, which includes QFN, TQFN, DFN, TDFN and STDFN, has exposed copper (unplated) at the end of the lead terminals due to the manufacturing
process. A solder fillet at the exposed copper edge cannot be guaranteed and is not required to ensure a proper bottom solder connection.