Creative Design & Innovation FOR ADMIN ONLYtawammodel.com/wp-content/uploads/2018/03/sample.pdf ·...
Transcript of Creative Design & Innovation FOR ADMIN ONLYtawammodel.com/wp-content/uploads/2018/03/sample.pdf ·...
STUDENT SECTION
Name Class
Student MOE number (SIS)
School MOE Number
STUDENT SIGNATURE
School name
FOR ADMIN ONLY MARKING RECORD
Section Section TOTALS
Section 1
Section 2
Section 3
MARKER SIGNATURE
TOTAL MARKS
MODERATOR SIGNATURE
Creative Design & Innovation
11 Advanced
Sample - Term 2
Date: February 2018
Time: TBC
Duration: 35 minutes
STUDENT INSTRUCTIONS – Students must attempt all questions. For this examination, you must have:
1. An ink pen – blue. 2. A pencil. 3. A ruler.
TEACHER NOTES & INSTRUCTIONS
Please tick the correct answers in RED INK and then write the mark awarded in the marking columns. With multiple mark answers highlight where the mark is awarded by underlining or by using an extra tick.
PLEASE NOTE – This SAMPLE paper is to guide students on question types ONLY.
It may not reflect the content for the final examination. Please refer to the coverage documents.
Page 1 of 5
SECTION 1 – Multiple choice
Choose and circle the correct answer – A, B, C or D. (1 mark each)
Example: A 9V battery supplies -
A. AC
B. SC
C. DC
D. a 12 V device
1. What type of signal is emitted by a loudspeaker?
A. microwave
B. digital
C. analogue
D. radio
2. _____________ indicates the minimum & maximum range in a resistor.
A. Resistance
B. Distance
C. Variance
D. Tolerance
3. A(n) _____________ can be used to measure different electrical values.
A. voltmeter
B. ammeter
C. multimeter
D. thermometer
4. A _________ is an output module in an electrical circuit.
A. wire
B. buzzer
C. current
D. breadboard
5. A(n) _____________ is not an output.
A. sensor
B. LED
C. LCD
D. speaker
/ 5
Page 2 of 5
SECTION 2 – Sequencing
In this question, you need to complete the order for the stages in a MICROCONTROLLER.
Fill boxes 1 - 5 with the word statements listed in the table shown below.
ONE possible answer will NOT be used in the sequence below.
1a – Identify the terminals of the electromagnetic relay shown below. (3 marks)
1b – List two parts of an electromagnetic relay.
Part 1 ________________________________________________________________
Part 2 _______________________________________________________ (2 marks)
Collects signals Control Unit Sends signals
Input Unit Analogue signals Output Unit
/ 5
SECTION 3 – Core content
A
B
C
/ 5
Microcontroller
Processes signals
1.
4. 5.
2. 3.
Page 3 of 5
2 - Study the diagram of a signal below. Answer the questions about the signal.
2a – What type of signal is shown in the diagram below? (1 mark)
2b - Label the 2 boxes to show which side of the signal is positive and which is
negative (-). (2 marks)
2c - Circle TWO of the devices below that use this kind of signal. (2 marks)
FILM CAMERA SMARTPHONE RADIO GAME
CONTROLLER
/ 5
Page 4 of 5
3 – A diagram of a faulty circuit is shown below -
3a – Identify TWO reasons why the LED’s are not lighting in the circuit shown. (2 marks)
a) _______________________________________
_______________________________________
b) _______________________________________
_______________________________________
3b – In the box below, draw a schematic diagram for a working circuit solution.
/ 5
Schematic Diagram
(3 Marks)
Page 5 of 5
4 – Match the words with their definition or image. (5 marks)
Write the matching letter in the correct box. The first one has been done for you.
COMPONENT Symbol
letter
SYMBOL
Voltmeter F A constant voltage or current. A
Switch
B
Potentiometer
C
DC
D
Microcontroller A three-terminal variable resistor E
Digital signal
F
You have now finished the examination.
/ 5
TOTAL
/ 30
Page 1 of 1
Creative Design & Innovation
Grade 11 Advanced Sample - Term 2 - Answer Key
Section 1 –
Multiple Choice
Question Answer
1 C
2 D
3 C
4 B
5 A
Section 2 –
Sequencing
Question Answer
1 Input Unit
2 Control Unit
3 Output Unit
4 Collects signals
5 Sends signals
Section 3 – Core content
Question Answer
1a– Diagram (3 marks)
1 marks each
A = NO
B = COM
C = NC
1b - Diagram (2 marks) (Any 2) - Electromagnet / Spring / armature / switch contacts = (1 mark each)
2a - SAQ (1 mark) Analogue Signal
2b - SAQ (2 marks) Top = positive (+) / Bottom = negative (-) = (1 mark each)
2c - SAQ (2 marks) Film camera & Radio = (1 mark each)
3a – SAQ (2 marks) Positive of battery needs to be connected to the positive power rails (rows) Legs of the LED (positive and negative terminals) are on the same connected column (any other relevant answer)
3b – SAQ (3 marks) 1 mark for each of the following connected
properly in correct order:
battery, resistor, LED
4 – Matching
(5 marks) Switch = D / Potentiometer = E / DC = A / Microcontroller = B / Digital Signal = C
Where student responses may vary
please use your professional
judgment. Be reasonable and
award marks ONLY when deserved
for answers given.
Marks will be awarded as indicated
on the examination paper. Specific
mark breakdowns for questions will
be written when necessary.