STRONG PARTNERS. TOUGH TRUCKS.

Counterbalanced stackerS1.0C, S1.2C, S1.5C

S1.0C, S1.2C, S1.5C

Equipment and weight:Weights (line 2.1) are based on the following specifications:S1.0C: Mast 2 972 mmS1.2C: Mast 2 972 mmS1.5C: Mast 2 972 mm

Specification Data is based on VDI 2198

S1.0C, S1.2C, S1.5C

Forks:S1.0C: 35 x 100 x 1 000 mm longS1.2C: 35 x 100 x 1 000 mm longS1.5C: 35 x 100 x 1 000 mm long

Fork spacing:Inside to inside: 240 mmOutside to outside: 672 mm

Mast and capacity informationValues shown are for standard equipment. When using non-standard equipment, these values may change. Please contact your Hyster dealer for information.

The rated capacities shown are for masts in a vertical position on trucks equipped with standard or sideshiftcarriage, and nominal length forks. Masts above the maximum fork heights shown in the mast table are classifiedas high lift, and depending on the tyre/tread configuration may require reduced capacity, restricted back tilt or widetread.

NOTE:

Specifications are affected by the condition

of the vehicle and how it is equipped, as well

as the nature and condition of the operating

area. If these specifications are critical, the

proposed application should be discussed

with your dealer.

¶ Bottom of forks

Mast tables:

With 150 mm free lift

Notice

Care must be exercised when handling

elevated loads. When the carriage

and/or load is elevated, truck stability

is reduced.Operators must be trained

and adhere to the instructions

contained in the Operating Manual.

Safety:

This truck conforms to the current EU requirements.

Hyster products are subject to change without notice.

Lift trucks illustrated may feature optional equipment.

Ast = Wa + x + l6 + a (see lines 4.33 & 4.34)

a = Minimum operating clearance

(V.D.I. standard = 200 mm BITA recommendation = 300 mm)

l6 = Load length

NOTE:

Specifications are affected by the condition

of the vehicle and how it is equipped, as well

as the nature and condition of the operating

area. If these specifications are critical, the

proposed application should be discussed

with your dealer.

¶ Bottom of forks

Mast tables:

With 150 mm free lift

Notice

Care must be exercised when handling

elevated loads. When the carriage

and/or load is elevated, truck stability

is reduced. Operators must be trained

and adhere to the instructions

contained in the Operating Manual.

Safety:

This truck conforms to the current EU requirements.

Hyster products are subject to change without notice.

Lift trucks illustrated may feature optional equipment.

Ast = Wa + x + l6 + a (see lines 4.33 & 4.34)

a = Minimum operating clearance

(V.D.I. standard = 200 mm BITA recommendation = 300 mm)

l6 = Load length

Dependability

� Tough counterbalance performance.

� Comprehensive selection of mast configurations.

� Specific options available to ensure trucks meet exact operation requirements, e.g. load back rest, FEM forksand carriages.

� CANbus electronics reduce wiring complexity, for increased reliability.

� Integral side shift as standard allows optimum fork positioning for all applications.

Productivity

� Operator-friendly tiller head controls for improved load handling.

� Power steering available for both pedestrian and stand-on operation.

� Compact chassis design improves handling in confined spaces.

� Automatic braking on release of the movement controls.

� Regenerative braking and anti-roll back as standard.

� Adjustable performance settings to suit specific operating conditions.

Ergonomics

� Tiller head ergonomically designed for maximum operator comfort.

� Controls positioned to allow operation with either hand.

� EPAS (Electronic Power Assistance Steering) system provides optimum directional control at any speed.

� Software speed reduction on cornering.

� On/off auxiliary functions for tilt and side shift.

� Vertically mounted lifting motor with dampers to reduce noise and vibration.

Serviceability

� Diagnostic indicators for early warning of maintenance requirements.

� Built in diagnostic system allows preventive maintenance communications, increasing uptime.

� Updated components permit extended service intervals.

� Driver Diagnostic Interface (DDI) informs operator in real-time about truck conditions.

� Hour meter and battery discharge indicator with lift interrupt fitted as standard.

Cost of ownership

� Powerful AC traction motor provides superior performance and increased load moves per hour.

� Increased load moves per hour reduces operating costs.

� Traction and hydraulics managed through MOSFET high frequency Combi controller.

� Intelligent management system optimises energy usage.

� Key-pad access allows greater management control.

Product Features

Hyster Europe, Flagship House, Reading Road North, Fleet, Hants GU51 4WD, England.

Tel: +44 (0) 1252 810261 Fax: +44 (0) 1252 770702

Email: info@hyster.co.uk http://www.hyster.co.uk

A division of NACCO Materials Handling Limited.

12/07/TLC Printed in EnglandForm No. 901278/0

Hyster®, ®, Vista® and Monotrol® are registered trademarks of Hyster Company in the United States and in certain other countries.TM, FortensTM, Pacesetter VSMTM, DuraMatchTM, DuraMatch PlusTM, TouchPointTM, TouchControlTM, EZXchange & HSMTM are trademarks

of Hyster Company in the United States and in certain other countries. TM

Strong Partners, Tough Trucks,

for Demanding Operations Everywhere.

Hyster supplies a complete product range,

including Warehouse trucks, IC and Electric

Counterbalanced trucks, Container Handlers

and Reach Stackers.

Hyster is committed to being much more than a

lift truck supplier. Our aim is to offer a complete

partnership capable of responding to the full

spectrum of materials handling issues:

Whether you need professional consultancy on

your fleet management, fully qualified service

support, or reliable parts supply, you can

depend on Hyster.

Our network of highly trained dealers provides

expert, responsive local support. They can offer

cost-effective finance packages and introduce

effectively managed maintenance programmes

to ensure that you get the best possible value.

Our business is dealing with your materials

handling needs so you can focus on the

success of your business today and in the

future.