copertina lamiere 2 -4 -...
Transcript of copertina lamiere 2 -4 -...
ITP H 20 /1010 ITP H 20 /1212
[14 Greche/Ribs] - Passo greche / Ribs step 75 mm Modulo utile / Working width 900 mm
[16 Greche/Ribs] - Passo greche / Ribs step 75 mmModulo utile / Working width 1125 mm
Particolare del giunto / Joint view
DISEGNO TECNICO - TECHNICAL DRAWING
DISEGNO TECNICO - TECHNICAL DRAWING
Particolare del giunto / Joint view
75
20
11,2900
20
8
75
1125
9,9
17
55
19
55
19
54
19
54
19
4 ST 4.L - REV. 1 - 11/2014
[9 Greche/Ribs] - Passo greche / Ribs step 112 mm Modulo utile / Working width 896 mm
[11 Greche/Ribs ] - Passo greche / Ribs step 112 mmModulo utile / Working width 1120 mm
Particolare del giunto / Joint view
DISEGNO TECNICO - TECHNICAL DRAWING
DISEGNO TECNICO - TECHNICAL DRAWING
Particolare del giunto / Joint view
112
28
896
26
18,5 10
23
28
80
32
80
32 112
1120
ITP H 28 / 1012 ITP H 28 / 1233
ST 4.L - REV. 1 - 11/2014 5
ITP H38 / 732 / D
Particolare del giunto / Joint view
ITP H 38 /915 / D
ITP H 38 /915 / R
Particolare del giunto / Joint view
ITP H 38 / 732 - ITP H 38 /915
DISEGNO TECNICO - TECHNICAL DRAWING
DISEGNO TECNICO - TECHNICAL DRAWING
37
28
38
183
155
16,5732
12,8
37
28
38
183
155
16,5915
12,8
ITP H38 / 732 / R
38
28
37
183
155
16,5
732
12,8
38
28
37
183
155
16,5915
12,8
Passo grecheRibs step 183 mm Modulo utile Working width 732 mm
[5 Greche/Ribs]
Passo grecheRibs step 183 mm Modulo utile Working width 915 mm
[6 Greche/Ribs]
6 ST 4.L - REV. 1 - 11/2014
Particolare del giunto / Joint view
ITP H 40 / D
ITP H 40 PdA / D
ITP H 40 PdA / R
ITP H 40 / R
250
40
100020
54
250
40
1000
20
54
ITP H40 e H40 Pda/1000[5 greche/Ribs] Passo greche / Ribs step 250 mm Modulo utile / Working width 1000 mm
DISEGNO TECNICO - TECHNICAL DRAWING
Particolare del giunto / Joint view
250
40
100020
1854
DISEGNO TECNICO - TECHNICAL DRAWING
DISEGNO TECNICO - TECHNICAL DRAWING
250
40
100020
5418
ST 4.L - REV. 1 - 11/2014 7
[9 Greche/Ribs] - Passo greche / Ribs step 112 mm - Modulo utile / Working width 896 mm
Vantaggi rispetto ad una lamiera grecata - Advantages over bare single sheet
• Maggiore isolamento acustico - Better acoustic insulation• Riduzione del fenomeno della condensa - Reduction of condensation phenomenal• Maggiore resistenza alla grandine - Better resistance to hail• Creazione tetto caldo ventilato - Realization warm ventilated roof• Maggiore resistenza al calpestio - Better resistance to walking
Versioni speciali - Special version
Alluminio centesimale goffrato - Centesimal embossed aluminum• COLORE NEUTRO - NEUTRAL COLOR• COLORE BIANCO - WHITE COLOR
Particolare del giunto - Joint view
DISEGNO TECNICO - TECHNICAL DRAWING
112
28
896
10
ITP MONO 28/1012Pannello mono lamiera - Single sheet panel
LASTRA GRECATA PROFILO 28 RIVESTITA DA 1 CM DI POLIURETANO NUDO SINGLE SHEET PROFILE 28 COVERED BY 1 CM OF BARE PU
8 ST 4.L - REV. 1 - 11/2014
150
55
750
150
55
600
150
55
900
ITP H 55 / 600 - ITP H 55 / 750 - ITP H 55 / 900
[5 Greche/Ribs] - Passo greche / Ribs step 150 mm Modulo utile / Working width 600 mm
[6 Greche/Ribs] - Passo greche / Ribs step 150 mm Modulo utile / Working width 750 mm
Particolare del giunto / Joint view
DISEGNO TECNICO - TECHNICAL DRAWING
DISEGNO TECNICO - TECHNICAL DRAWING
56
56
1296
9621
12
26
[7 Greche/Ribs] - Passo greche / Ribs step 150 mm Modulo utile / Working width 900 mm
DISEGNO TECNICO - TECHNICAL DRAWING
56
96
3539
ST 4.L - REV. 1 - 11/2014 9
I
[
ITP H75 / 570 / D
[4 Greche / Ribs]Passo greche / Ribs step 190 mm Modulo utile / Working width 570 mm
[4 Greche / Ribs] Passo greche / Ribs step 273 mm Modulo utile / Working width 820 mm
Particolare del giunto / Joint view
ITP H 75 / 820 / D
ITP H 75 / 570 ITP H 75 / 820
DISEGNO TECNICO - TECHNICAL DRAWING
DISEGNO TECNICO - TECHNICAL DRAWINGParticolare del giunto / Joint view
0 / D
73,5 75
570
64
4037,5 190
ITP H75 / 570 / R
73,575
570
64
40 37,5190
73,5 75
820
64
4037,5 273
ITP H 75 / 820 / R
73,575
820
64
40 37,5273
10 ST 4.L - REV. 1 - 11/2014
ITP H106 / 798 / D
ITP H106 / 798 / R
[4 Greche / Ribs]Passo greche / Ribs step 250 mm Modulo utile / Working width 750 mm
Particolare del giunto / Joint view
[4 Greche / Ribs]Passo greche / Ribs step 333 mm Modulo utile / Working width 1000 mm
Particolare del giunto / Joint view
ITPH 106 / 798 ITPH 106 / 1040
DISEGNO TECNICO - TECHNICAL DRAWING
DISEGNO TECNICO - TECHNICAL DRAWING
106
750
120
25042
34
15
130
106
750
120
250 42
34
15
130
106
1000120
333
213
42
34
15
106
1000120
333
213
42
34
15
ITP H 106 / 1040 / D
ITP H 106 / 1040 / R
ST 4.L - REV. 1 - 11/2014 11
Tabelle portata ACCIAIO - STEEL load tables Tabelle portate ALLUMINIO - ALLUMINUM load tables
Sezione lorda ALLUMINIO - ALLUMINUM gross sectionSezione lorda ACCIAIO - STEEL gross sectionSpessore nominaleNominal thickness (mm)Peso nominale *Weight nominal (Kg./m2)
* peso calcolato rispetto alla larghezza totale - weight calculated relevant to total width
P
l
ITPH 201010 - 1212
JY (cm4/m)
(cm3/m)
(cm3/m)
(cm3/m)
We,inf
Wp
We,sup
0,50
3,62
3,53
3,53
4,18
0,60
4,36
4,25
4,25
5,08
0,70 0,80
4,99
4,87
4,87
5,87
5,66
5,52
5,52
6,73
1,00
6,84
6,67
6,67
8,29
1,20
4,8 5,8 6,8 7,7 9,7 11,6
7,89
7,70
7,70
9,76
0,60
4,49
4,38
4,38
5,25
0,70 0,80
5,12
5,00
5,00
6,03
5,79
5,65
5,65
6,89
1,00
7,02
6,85
6,85
8,52
1,20
8,07
7,87
7,87
9,99
Larghezza efficace appoggio: 50 mm
Working width support: 50 mm
1,75 2,00 2,25 2,50 2,75 3,00 3,25 3,50 3,75 4,000,75 1,00 1,25 1,50 1,75 2,00 2,25 2,50 2,75 3,00 3,25 3,50 3,75 4,000,75 1,00 1,25 1,50l = m
630
930
795
255
380
325
P =
Kg.
/m2
120
185
155
65
100
80
55
- 525 260 140 80
- 610 300 160 90 55
Spessorenominale
mm
0,5
0,7
0,8
1,0
1,2
0,6
1000 435 210 115 65
Nominalthickness
Valori in BLU: stati limite ultimoCarichi variabili uniformemente distribuitiVariable uniformly distributed loads BLU values: ultimate limit states
Valori in ROSSO: stati limite di esercizio (limitazione freccia 1/200 della luce)RED values: serviceability limit states (deflection 1/200 span)
2,0 2,3 2,7 3,3 4,0
440
650
855
540
260
350
430
300
4951000
125
165
210
145
65
90
240
75
110 60
130 70
245
340
425
290
90
130
165
110
55
70
490 190 85
Larghezza efficace appoggio: 50 mm
Working width support: 50 mm
1,75 2,00 2,25 2,50 2,75 3,00 3,25 3,50 3,75 4,000,75 1,00 1,25 1,50 1,75 2,00 2,25 2,50 2,75 3,00 3,25 3,50 3,75 4,000,75 1,00 1,25 1,50l = m
P =
Kg.
/m2
Spessorenominale
mm
0,5
0,7
0,8
1,0
1,2
0,6
Nominalthickness
Larghezza efficace appoggio: 50 mm
Working width support: 50 mm
1,75 2,00 2,25 2,50 2,75 3,00 3,25 3,50 3,75 4,000,75 1,00 1,25 1,50 1,75 2,00 2,25 2,50 2,75 3,00 3,25 3,50 3,75 4,000,75 1,00 1,25 1,50l = m
P =
Kg.
/m2
Spessorenominale
mm
0,5
0,7
0,8
1,0
1,2
0,6
Nominalthickness
490
665
820
575
195
270
335
230
90
125
160
105
65
80
945 385 185 95 50
55
590
945
1000
780
-
-
360
560
640
475
775
240
410
475
315
590
900 700
160
265
305
215
110
135
370
160
185
225
65
85
100
115
140
55
65
75
90
425 260 165 110
50
60
70
55
65
80 50
725
1000
960
445
705
805
590
-
- 975
250
370
420
315
510
135
205
235
175
80
100
285
120
140
170
60
75
85
105
- - 590 330 200 125
P P
l l
P P P
l l l
12 ST 4.L - REV. 1 - 11/2014
Tabelle portata ACCIAIO - STEEL load tables Tabelle portate ALLUMINIO - ALLUMINUM load tables
Sezione lorda ALLUMINIO - ALLUMINUM gross sectionSezione lorda ACCIAIO - STEEL gross sectionSpessore nominaleNominal thickness (mm)Peso nominale *Weight nominal (Kg./m2)
P
l
* peso calcolato rispetto alla larghezza totale - weight calculated relevant to total width
ITPH 281012 - 1233
JY (cm4/m)
(cm3/m)
(cm3/m)
(cm3/m)
We,inf
Wp
We,sup
0,50 0,60 0,70 0,80 1,00 1,20 0,60 0,70 0,80 1,00 1,20
Larghezza efficace appoggio: 50 mm
Working width support: 50 mm
1,75 2,00 2,25 2,50 2,75 3,00 3,25 3,50 3,75 4,000,75 1,00 1,25 1,50 1,75 2,00 2,25 2,50 2,75 3,00 3,25 3,50 3,75 4,000,75 1,00 1,25 1,50l = m
P =
Kg.
/m2
Spessorenominale
mm
0,5
0,7
0,8
1,0
1,2
0,6
Nominalthickness
Larghezza efficace appoggio: 50 mm
Working width support: 50 mm
1,75 2,00 2,25 2,50 2,75 3,00 3,25 3,50 3,75 4,000,75 1,00 1,25 1,50 1,75 2,00 2,25 2,50 2,75 3,00 3,25 3,50 3,75 4,000,75 1,00 1,25 1,50l = m
P =
Kg.
/m2
Spessorenominale
mm
0,5
0,7
0,8
1,0
1,2
0,6
Nominalthickness
Larghezza efficace appoggio: 50 mm
Working width support: 50 mm
1,75 2,00 2,25 2,50 2,75 3,00 3,25 3,50 3,75 4,000,75 1,00 1,25 1,50 1,75 2,00 2,25 2,50 2,75 3,00 3,25 3,50 3,75 4,000,75 1,00 1,25 1,50l = m
P =
Kg.
/m2
Spessorenominale
mm
0,5
0,7
0,8
1,0
1,2
0,6
Nominalthickness
P P
l l
P P P
l l l
7,05
5,04
5,04
5,82
8,54
6,10
6,10
7,10
9,85
7,03
7,03
8,23
11,25
8,03
8,03
9,47
13,78
9,84
9,84
11,76
16,15
11,53
11,53
13,97
4,8 5,8 6,7 7,7 9,6 11,5
825
1000
1000
460
715
840
600
-
-
-
235
355
420
295
545
130 75
195
235
165 95 60
305
115 70
140 85 55
185 115 75
- - 640 360 215 135 90 55
570
955
1000
1000
765
355
595
735
480
-
- -
245
410
505
330
690
175
295
365
235
130
180
495
220
270
365
825 585 505
100 75 60
140
175
215
290
105 80 55
135 95 65
165
210
115 80 55
145 105 75 55
365 250 175 125 90 65
690
1000
1000
1000
930
-
-
-
435
730
895
585
-
300
505
620
405
215
365
450
295
600
705
160 100 65
205
245
285
370
435
130 85 55
155 105 70
185
240
280
125 85 60
160 110 75 55
190 130 95 65
845
8,82
6,30
6,30
7,34
10,12
7,23
7,23
8,47
11,51
8,22
8,22
9,70
14,17
10,12
10,12
12,11
16,52
11,80
11,80
14,30
2,0 2,3 2,6 3,3 4,0
465
640
825
545
185
255
335
220
120 60
160 80
405 195 100 55
100 50
85
420
640
890
520
260
400
560
325
175
275
380
220
125 80
185
715 490
160 95 55
110 65
240 140 85 55
285 170 105 651000
1000
510 320 185 55
775
630
490
660
400
255
325
215
140 80
180 105 60
800 395 220 130 75
115
100
65
1000
-
Valori in BLU: stati limite ultimoCarichi variabili uniformemente distribuitiVariable uniformly distributed loads BLU values: ultimate limit states
Valori in ROSSO: stati limite di esercizio (limitazione freccia 1/200 della luce)RED values: serviceability limit states (deflection 1/200 span)
ST 4.L - REV. 1 - 11/2014 13
Tabelle portata ACCIAIO - STEEL load tables Tabelle portate ALLUMINIO - ALLUMINUM load tables
Sezione lorda ALLUMINIO - ALLUMINUM gross sectionSezione lorda ACCIAIO - STEEL gross sectionSpessore nominale *Nominal thickness (mm)Peso nominaleWeight nominal (Kg./m2)
P
l
* peso calcolato rispetto alla larghezza utile - weight calculated relevant to working width
ITPH 38-D732 - 915
JY (cm4/m)
(cm3/m)
(cm3/m)
(cm3/m)
We,inf
Wp
We,sup
0,50 0,60 0,70 0,80 1,00 1,20 0,60 0,70 0,80 1,00 1,20
Larghezza efficace appoggio: 50 mm
Working width support: 50 mm
1,75 2,00 2,25 2,50 2,75 3,00 3,25 3,50 3,75 4,000,75 1,00 1,25 1,50 1,75 2,00 2,25 2,50 2,75 3,00 3,25 3,50 3,75 4,000,75 1,00 1,25 1,50l = m
P =
Kg.
/m2
Spessorenominale
mm
0,5
0,7
0,8
1,0
1,2
0,6
Nominalthickness
Larghezza efficace appoggio: 50 mm
Working width support: 50 mm
1,75 2,00 2,25 2,50 2,75 3,00 3,25 3,50 3,75 4,000,75 1,00 1,25 1,50 1,75 2,00 2,25 2,50 2,75 3,00 3,25 3,50 3,75 4,000,75 1,00 1,25 1,50l = m
P =
Kg.
/m2
Spessorenominale
mm
0,5
0,7
0,8
1,0
1,2
0,6
Nominalthickness
Larghezza efficace appoggio: 50 mm
Working width support: 50 mm
1,75 2,00 2,25 2,50 2,75 3,00 3,25 3,50 3,75 4,000,75 1,00 1,25 1,50 1,75 2,00 2,25 2,50 2,75 3,00 3,25 3,50 3,75 4,000,75 1,00 1,25 1,50l = m
P =
Kg.
/m2
Spessorenominale
mm
0,5
0,7
0,8
1,0
1,2
0,6
Nominalthickness
P P
l l
P P P
l l l
9,75
3,30
5,04
5,4
11,79
4,00
13,89
6,15
6,4
13,57
4,60
15,96
7,13
15,47
5,25
18,17
8,19
18,88
6,41
22,10
10,17
22,04
7,49
25,71
12,07
7,5 8,6 10,7 12,9
685 380 240 165 120 90 60
965 540 340 235 170 110 75 50
1000 855 545 315 195 125 85 60
-
-
1000
- -
- -
625 360 220 145 100 70 50
765 435 270 175 120 85 60
895 510 315 205 140 100 70 50
490 325 235 175 140 110 90 75 65 55
660 440 315 240 185 150 125 105 85 75 55
815
995
540 390 295 230 185 155 130 110 85 65 50
660 475 360 280 225 185 155 135 100 75 60
1000
1000
885 635 480 380 305 250 210 160 120 95 70 55
805 610 475 385 315 255 190 140 110 85 65 50
590 390 285 215 170 135 110 85 65
790 530 380 290 230 185 150 105 75 60
660980 470 360 285 230 170 120 90 65 50
1000 800 575 440 345 285 195 140 105 75 60
1000 775 590 465 345 240 170 125 95 70 55-
745980 585 405 280 200 145 110 80 60 50- -
4,13
14,34
12,18
6,35
13,94
16,39
4,73
7,33
15,84
18,59
5,37
8,39
19,42
22,72
6,60
10,47
22,55
26,29
7,66
12,37
2,2 3,0 3,72,6 4,4
520 290 155 85 50
645
840
360 180 60
415 205 115
100
70
1000 255510 140 85 50
- 295590 165 95 60
370 245 180 135 105 85 60
450 300 215 165 130 70
550 365 260 200 155 115
100
80 55
495750 355 270 210 145 95 65
625950 450 340 255 165 110 75 55
440 295
540 365
440660
600900
1000 760
215 165
265 200
320 225
435 280
545 325
70
120
105
80 50
140 90 60
170 110 75
200 125 85 55
50
11,50
Valori in BLU: stati limite ultimoCarichi variabili uniformemente distribuitiVariable uniformly distributed loads BLU values: ultimate limit states
Valori in ROSSO: stati limite di esercizio (limitazione freccia 1/200 della luce)RED values: serviceability limit states (deflection 1/200 span)
14 ST 4.L - REV. 1 - 11/2014
Tabelle portata ACCIAIO - STEEL load tables Tabelle portate ALLUMINIO - ALLUMINUM load tables
Sezione lorda ALLUMINIO - ALLUMINUM gross sectionSezione lorda ACCIAIO - STEEL gross sectionSpessore nominaleNominal thickness (mm)Peso nominale *Weight nominal (Kg./m2)
P
l
* peso calcolato rispetto alla larghezza utile - weight calculated relevant to working width
ITPH 38-R732 - 915
JY (cm4/m)
(cm3/m)
(cm3/m)
(cm3/m)
We,inf
Wp
We,sup
Larghezza efficace appoggio: 50 mm
Working width support: 50 mm
1,75 2,00 2,25 2,50 2,75 3,00 3,25 3,50 3,75 4,000,75 1,00 1,25 1,50 1,75 2,00 2,25 2,50 2,75 3,00 3,25 3,50 3,75 4,000,75 1,00 1,25 1,50l = m
P =
Kg.
/m2
Spessorenominale
mm
0,5
0,7
0,8
1,0
1,2
0,6
Nominalthickness
Larghezza efficace appoggio: 50 mm
Working width support: 50 mm
1,75 2,00 2,25 2,50 2,75 3,00 3,25 3,50 3,75 4,000,75 1,00 1,25 1,50 1,75 2,00 2,25 2,50 2,75 3,00 3,25 3,50 3,75 4,000,75 1,00 1,25 1,50l = m
P =
Kg.
/m2
Spessorenominale
mm
0,5
0,7
0,8
1,0
1,2
0,6
Nominalthickness
Larghezza efficace appoggio: 50 mm
Working width support: 50 mm
1,75 2,00 2,25 2,50 2,75 3,00 3,25 3,50 3,75 4,000,75 1,00 1,25 1,50 1,75 2,00 2,25 2,50 2,75 3,00 3,25 3,50 3,75 4,000,75 1,00 1,25 1,50l = m
P =
Kg.
/m2
Spessorenominale
mm
0,5
0,7
0,8
1,0
1,2
0,6
Nominalthickness
P P
l l
P P P
l l l
930 525 335 220 135 90 60
675 430 270 165 110 75 501000
1000
- 805
945
515 315 195 125 85 60
- 605 360 220 145 100 70 50
- 765 435 270 175 120 85 60
- - 895 510 315 205 140 100 70 50
485 310 210 150 110 85 70 55
625 495 340 235 170 130 100 80 65 55
755
900
620 435 320 245 190 155 125 105 85 65 50
745
985
515 380 290 225 180 150 125 100 75 60
1000
1000-
675 490 375 290 235 190 155 120 95 70 55
835 605 455 355 275 220 180 140 110 85 65 50
580 375 255
750 590 415
745910 525
1000
1000
900 625
825-
1000- -
185 140 110 85 70 55
295 215 165 125 100 75 55
385 295 235 170 120 90 65 50
460 355 280 195 140 100 75 55
600 460 345 240 170 125 95 70 55
740 560 405 280 200 145 110 80 60 50
735
880
1000
-
-
320 160 90 50
365 180 100 60
415 205 115 70
255510 140 85 50
295590 165 95 60
355 225 150 110 80 60 50
435 305 190 135 100 80 60
520 410 285 205 145 110 80 55
570690 395 290 220 145 95 65
715 490 360 255 165 110 75 551000
425 270 185 135 100 70
520 365 240 170 120 80 50
490625 345 225 140 90 60
685835 480 280 170 110 75 50
570860 325 200 125 85 551000
0,50 0,60 0,70 0,80 1,00 1,20 0,60 0,70 0,80 1,00 1,20
9,75
3,30
11,50
4,97
11,79
4,00
13,89
6,04
13,57
4,60
15,96
6,98
15,47
5,25
18,17
8,00
18,88
6,41
22,10
9,85
22,04
7,49
25,71
11,62
5,4 7,5 8,66,4 10,7 12,9 2,2 2,6 3,0 3,7 4,4
4,13
14,34
12,18
6,24
13,94
16,39
4,73
7,17
15,84
18,59
5,37
8,19
19,42
22,72
6,60
10,14
22,55
26,29
7,66
11,89
Valori in BLU: stati limite ultimoCarichi variabili uniformemente distribuitiVariable uniformly distributed loads BLU values: ultimate limit states
Valori in ROSSO: stati limite di esercizio (limitazione freccia 1/200 della luce)RED values: serviceability limit states (deflection 1/200 span)
ST 4.L - REV. 1 - 11/2014 15
Tabelle portata ACCIAIO - STEEL load tables Tabelle portate ALLUMINIO - ALLUMINUM load tables
Sezione lorda ALLUMINIO - ALLUMINUM gross sectionSezione lorda ACCIAIO - STEEL gross sectionSpessore nominaleNominal thickness (mm)Peso nominale *Weight nominal (Kg./m2)
P
l
* peso calcolato rispetto alla larghezza utile - weight calculated relevant to working width
Valori in ROSSO: stati limite di esercizio (limitazione freccia 1/200 della luce)RED values: serviceability limit states (deflection 1/200 span)
ITPH40/40PdA-D1000
JY (cm4/m)
(cm3/m)
(cm3/m)
(cm3/m)
We,inf
Wp
We,sup
0,50 0,60 0,70 0,80 1,00 1,20 0,60 0,70 0,80 1,00 1,20
Larghezza efficace appoggio: 50 mm
Working width support: 50 mm
1,75 2,00 2,25 2,50 2,75 3,00 3,25 3,50 3,75 4,000,75 1,00 1,25 1,50 1,75 2,00 2,25 2,50 2,75 3,00 3,25 3,50 3,75 4,000,75 1,00 1,25 1,50l = m
P =
Kg.
/m2
Spessorenominale
mm
0,5
0,7
0,8
1,0
1,2
0,6
Nominalthickness
Larghezza efficace appoggio: 50 mm
Working width support: 50 mm
1,75 2,00 2,25 2,50 2,75 3,00 3,25 3,50 3,75 4,000,75 1,00 1,25 1,50 1,75 2,00 2,25 2,50 2,75 3,00 3,25 3,50 3,75 4,000,75 1,00 1,25 1,50l = m
P =
Kg.
/m2
Spessorenominale
mm
0,5
0,7
0,8
1,0
1,2
0,6
Nominalthickness
Larghezza efficace appoggio: 50 mm
Working width support: 50 mm
1,75 2,00 2,25 2,50 2,75 3,00 3,25 3,50 3,75 4,000,75 1,00 1,25 1,50 1,75 2,00 2,25 2,50 2,75 3,00 3,25 3,50 3,75 4,000,75 1,00 1,25 1,50l = m
P =
Kg.
/m2
Spessorenominale
mm
0,5
0,7
0,8
1,0
1,2
0,6
Nominalthickness
P P
l l
P P P
l l l
3,91
15,37
12,47
6,00
14,23
17,51
4,46
6,92
16,12
19,80
5,06
7,93
19,64
24,03
6,17
9,89
22,65
27,61
7,12
11,69
2,0 2,7 3,42,4 4,1
495 280 145 75
610
835
335 170 90 50
410 200 105 60
1000 245505 135 75
- 285585 155 90 50
240 160 115 85 65 50
300 195 140 105 80 60 50
365 240 170 130 100 75 60
335505 235 175 135 110 85 60
420640 300 225 175 135 105 70
290 195
360 240
295440
405610
515775
140 105 80
170 130 100
210 160 125
290 220
370 280
55
70
80 50
165 100 65
190 120 75 50
10,00
12,36
3,14
4,76
12,07
14,88
3,78
5,80
13,84
17,04
4,34
6,73
15,74
19,34
4,94
7,74
19,09
23,37
6,00
9,60
22,13
26,99
6,96
11,40
4,9 5,9 6,9 7,9 9,8 11,8
665 365
835
670
230
530
425
155 110 80 50
310
270 160 100 65
190 120 75 50
-
-
-
760 435 265 170 110 75 50
- - 890 505 305 195 130 90 60
1000
1000
965 610 355 215 135 90 60
335
550
445
225
365
445670
295
605905
160
265
320
215
435
765 550
120
200
240
160
95
125
325
155
190
255
75 60
100
125
150
205
80 65 55
100 80 70 55 50
125
165
415 325 260 210
100 85 70 60 50
140 115 95 80 65
170 140 120 100 75 551000
155 130 95 65 50
210 165 115 85 60
265 190 135 100 75 55
405
535
665
810
270
445
540
360
735
935
195
320
390
260
530
150
245
295
195
115 90 75 60 50
155
405
190
235
315
125 100 85 70 50
155 125 105 80 60
190
255
- 675 510 400 325
1000
Valori in BLU: stati limite ultimoCarichi variabili uniformemente distribuitiVariable uniformly distributed loads BLU values: ultimate limit states
16 ST 4.L - REV. 1 - 11/2014
Tabelle portata ACCIAIO - STEEL load tables Tabelle portate ALLUMINIO - ALLUMINUM load tables
Sezione lorda ALLUMINIO - ALLUMINUM gross sectionSezione lorda ACCIAIO - STEEL gross sectionSpessore nominaleNominal thickness (mm)Peso nominale *Weight nominal (Kg./m2)
P
l
ITPH40/40PdA-R1000
JY (cm4/m)
(cm3/m)
(cm3/m)
(cm3/m)
We,inf
Wp
We,sup
0,50 0,60 0,70 0,80 1,00 1,20 0,60 0,70 0,80 1,00 1,20
Larghezza efficace appoggio: 50 mm
Working width support: 50 mm
1,75 2,00 2,25 2,50 2,75 3,00 3,25 3,50 3,75 4,000,75 1,00 1,25 1,50 1,75 2,00 2,25 2,50 2,75 3,00 3,25 3,50 3,75 4,000,75 1,00 1,25 1,50l = m
P =
Kg.
/m2
Spessorenominale
mm
0,5
0,7
0,8
1,0
1,2
0,6
Nominalthickness
Larghezza efficace appoggio: 50 mm
Working width support: 50 mm
1,75 2,00 2,25 2,50 2,75 3,00 3,25 3,50 3,75 4,000,75 1,00 1,25 1,50 1,75 2,00 2,25 2,50 2,75 3,00 3,25 3,50 3,75 4,000,75 1,00 1,25 1,50l = m
P =
Kg.
/m2
Spessorenominale
mm
0,5
0,7
0,8
1,0
1,2
0,6
Nominalthickness
Larghezza efficace appoggio: 50 mm
Working width support: 50 mm
1,75 2,00 2,25 2,50 2,75 3,00 3,25 3,50 3,75 4,000,75 1,00 1,25 1,50 1,75 2,00 2,25 2,50 2,75 3,00 3,25 3,50 3,75 4,000,75 1,00 1,25 1,50l = m
P =
Kg.
/m2
Spessorenominale
mm
0,5
0,7
0,8
1,0
1,2
0,6
Nominalthickness
P P
l l
P P P
l l l
13,37
3,68
11,54
5,55
13,20
4,21
15,26
6,39
14,98
4,78
17,28
7,31
18,33
5,86
21,05
9,09
21,23
6,79
24,28
10,71
2,0 2,7 3,42,4 4,1
595 290 140 75
700
820
335 160 85
380 185 100 55
1000 230470 125 70
- 265545 145 80
310 195 130 90 65 50
380 245 160 115 85 60
465
620
760
295 195 140 100 75 60
510 350 250 190 125 80 50
655 445 320 230 145 95 60
370 240
460 295
360560
615750
795925
160 115 85
200 145 105
245 175 120
425 255
525 295
55
65
75
150 95 60
175 110 70
9,24
2,94
10,74
4,41
11,17
3,56
12,95
5,37
12,84
4,09
14,85
6,22
14,63
4,67
16,88
7,14
17,81
5,69
20,47
8,83
20,74
6,63
23,73
10,45
4,9 5,9 6,9 7,9 9,8 11,8
770 430
645
545965
275
410
345
185 120 75
235
280
150 95 60
175 110 70
-
-
620 400 245 155 105 70
-
-
755 470 285 185 120 80 55
1000
1000
775
970
480 330 200 125 80 55
405
675
560
260
515
680805
360
905
175
350
465
240
615
760
125
250
340
170
90
125
445
190
255
335
70 55
95
145
200
260
75 55
115 90 70 55
155
200
545 410 310 240
125 100 80 60
160 130 105 5575
190 155 125 90 70 50
1000
1000
175 120 85 60
215 150 105 75 55
250 175 125 90 65 50
490
675
820
980
315
625
825
435
215
430
570
295
750
155
310
415
210
115 90 70 55
160
545
235
315
410
120 95 75 60
180 145 105 75 55
245
315
- - 930 670 505 370
1000 1000
* peso calcolato rispetto alla larghezza utile - weight calculated relevant to working width
Valori in BLU: stati limite ultimoCarichi variabili uniformemente distribuitiVariable uniformly distributed loads BLU values: ultimate limit states
Valori in ROSSO: stati limite di esercizio (limitazione freccia 1/200 della luce)RED values: serviceability limit states (deflection 1/200 span)
ST 4.L - REV. 1 - 11/2014 17
Tabelle portata ACCIAIO - STEEL load tables Tabelle portate ALLUMINIO - ALLUMINUM load tables
Sezione lorda ALLUMINIO - ALLUMINUM gross sectionSezione lorda ACCIAIO - STEEL gross sectionSpessore nominaleNominal thickness (mm)Peso nominale *Weight nominal (Kg./m2)
P
l
* peso calcolato rispetto alla larghezza totale - weight calculated relevant to total width
ITPMono 281012
JY (cm4/m)
(cm3/m)
(cm3/m)
(cm3/m)
We,inf
Wp
We,sup
0,50 0,60 0,70 0,80 1,00 1,20 0,60 0,70 0,80 1,00 1,20
Larghezza efficace appoggio: 50 mm
Working width support: 50 mm
1,75 2,00 2,25 2,50 2,75 3,00 3,25 3,50 3,75 4,000,75 1,00 1,25 1,50 1,75 2,00 2,25 2,50 2,75 3,00 3,25 3,50 3,75 4,000,75 1,00 1,25 1,50l = m
P =
Kg.
/m2
Spessorenominale
mm
0,5
0,7
0,8
1,0
1,2
0,6
Nominalthickness
Larghezza efficace appoggio: 50 mm
Working width support: 50 mm
1,75 2,00 2,25 2,50 2,75 3,00 3,25 3,50 3,75 4,000,75 1,00 1,25 1,50 1,75 2,00 2,25 2,50 2,75 3,00 3,25 3,50 3,75 4,000,75 1,00 1,25 1,50l = m
P =
Kg.
/m2
Spessorenominale
mm
0,5
0,7
0,8
1,0
1,2
0,6
Nominalthickness
Larghezza efficace appoggio: 50 mm
Working width support: 50 mm
1,75 2,00 2,25 2,50 2,75 3,00 3,25 3,50 3,75 4,000,75 1,00 1,25 1,50 1,75 2,00 2,25 2,50 2,75 3,00 3,25 3,50 3,75 4,000,75 1,00 1,25 1,50l = m
P =
Kg.
/m2
Spessorenominale
mm
0,5
0,7
0,8
1,0
1,2
0,6
Nominalthickness
P P
l l
P P P
l l l
7,05
5,04
5,04
5,82
8,54
6,10
6,10
7,10
9,85
7,03
7,03
8,23
11,25
8,03
8,03
9,47
13,78
9,84
9,84
11,76
16,15
11,53
11,53
13,97
5,2 6,2 7,2 8,1 10,0 12,0
825
1000
1000
460
715
840
600
-
-
-
235
355
420
295
545
130 75
195
235
165 95 60
305
115 70
140 85 55
185 115 75
- - 640 360 215 135 90 55
570
955
1000
1000
765
355
595
735
480
-
- -
245
410
505
330
690
175
295
365
235
130
180
495
220
270
365
825 585 505
100 75 60
140
175
215
290
105 80 55
135 95 65
165
210
115 80 55
145 105 75 55
365 250 175 125 90 65
690
1000
1000
1000
930
-
-
-
435
730
895
585
-
300
505
620
405
215
365
450
295
600
705
160 100 65
205
245
285
370
435
130 85 55
155 105 70
185
240
280
125 85 60
160 110 75 55
190 130 95 65
845
8,82
6,30
6,30
7,34
10,12
7,23
7,23
8,47
11,51
8,22
8,22
9,70
14,17
10,12
10,12
12,11
16,52
11,80
11,80
14,30
2,4 2,8 3,1 3,8 4,4
465
640
825
545
185
255
335
220
120 60
160 80
405 195 100 55
100 50
85
420
640
890
520
260
400
560
325
175
275
380
220
125 80
185
715 490
160 95 55
110 65
240 140 85 55
285 170 105 651000
1000
510 320 185 55
775
630
490
660
400
255
325
215
140 80
180 105 60
800 395 220 130 75
115
100
65
1000
-
Valori in BLU: stati limite ultimoCarichi variabili uniformemente distribuitiVariable uniformly distributed loads BLU values: ultimate limit states
Valori in ROSSO: stati limite di esercizio (limitazione freccia 1/200 della luce)RED values: serviceability limit states (deflection 1/200 span)
18 ST 4.L - REV. 1 - 11/2014
Tabelle portata ACCIAIO - STEEL load tables Tabelle portate ALLUMINIO - ALLUMINUM load tables
Sezione lorda ALLUMINIO - ALLUMINUM gross sectionSezione lorda ACCIAIO - STEEL gross sectionSpessore nominaleNominal thickness (mm)Peso nominale *Weight nominal (Kg./m2)
P
l
JY (cm4/m)
(cm3/m)
(cm3/m)
(cm3/m)
We,inf
Wp
We,sup
0,50 0,60 0,70 0,80 1,00 1,20 0,60 0,70 0,80 1,00 1,20
Larghezza efficace appoggio: 50 mm
Working width support: 50 mm
2,50 2,75 3,00 3,25 3,50 3,75 4,00 4,25 4,50 4,75 5,001,00 1,50 2,00 2,25 2,50 2,75 3,00 3,25 3,50 3,75 4,00 4,25 4,50 4,75 5,001,00 1,50 2,00 2,25
2,50 2,75 3,00 3,25 3,50 3,75 4,00 4,25 4,50 4,75 5,001,00 1,50 2,00 2,25
2,50 2,75 3,00 3,25 3,50 3,75 4,00 4,25 4,50 4,75 5,001,00 1,50 2,00 2,25
2,50 2,75 3,00 3,25 3,50 3,75 4,00 4,25 4,50 4,75 5,001,00 1,50 2,00 2,25
2,50 2,75 3,00 3,25 3,50 3,75 4,00 4,25 4,50 4,75 5,001,00 1,50 2,00 2,25
l = m
P =
Kg.
/m2
Spessorenominale
mm
0,5
0,7
0,8
1,0
1,2
0,6
Nominalthickness
Larghezza efficace appoggio: 50 mm
Working width support: 50 mm
l = m
P =
Kg.
/m2
Spessorenominale
mm
0,5
0,7
0,8
1,0
1,2
0,6
Nominalthickness
Larghezza efficace appoggio: 50 mm
Working width support: 50 mm
l = m
P =
Kg.
/m2
Spessorenominale
mm
0,5
0,7
0,8
1,0
1,2
0,6
Nominalthickness
P P
l l
P P P
l l l
35,33
12,85
12,85
14,58
43,13
15,68
15,68
17,86
50,05
18,20
18,20
20,79
57,61
20,95
20,95
24,01
71,62
26,04
26,04
30,05
85,17
30,97
30,97
35,97
6,5 7,9 9,2 10,5 13,1 15,7
850
1000
1000
370 200
540
685
845
295
155 120
-
-
-
-
90 65
230 165 115 85 60
375 275 195 140 105 75 55
465 330 230 170 125 90 70 50
620 425 305 220 165 120 90 70 50
- 770 530 380 275 205 155 120 90 70 50
505
865
1000
1000
690
-
-
270
465
575
370
810
165
225
285
360
505
665 545 455 385 340 290 250 215 190 165 145
125 105 85 70 60 50
185
235
295 245 205 175 150 130 115 100 85 75
55 50
415 345 290 250 220 190 165 140 125 105
115 95
65 55
95 75
150 125 105 90 80 65 55 50
195 165 140 120 100 90 75 65
605
1000
1000
825
-
-
-
320
560
700
985
445
195
350
440
620
815
280
160 130 105 75 6590 55
290 240 205 175 150 130
360
510
670
425 360 310 265 205
560 475 420 325 255
300 255 215 190 155
230 190 160 135 115 100 85 65
105 80 5065
50
125 95 6075
160 130 6580100 50
200 160 85105130 65
44,57
16,21
16,21
18,47
51,47
18,72
18,72
21,39
59,02
21,46
21,46
24,61
73,75
26,82
26,82
30,96
87,24
31,73
31,73
36,86
2,7 3,2 3,6 4,5 5,4
370 140 90 60
475 185 120 80 55
585 230 150 100 70
265 100 65
360 185 110 85 70
435 225 135 110 90
55
245 145 115 95 80 65 55
305 185 150 125 105 85 75
640
315 120 75 50835
570
815
460
290
55
435 270
570 355
220 180 150 130 100 75 55
90 70 50240 200 165 1201000
1000
70
550 295 180 145 120 85 60
50
680 370 230 190 140 100 70 50
975 530 330 265 185 130 95 70 50
690 435 320 225 160 115 85 601000
-
-
* peso calcolato rispetto alla larghezza utile - weight calculated relevant to working width
Valori in BLU: stati limite ultimoCarichi variabili uniformemente distribuitiVariable uniformly distributed loads BLU values: ultimate limit states
Valori in ROSSO: stati limite di esercizio (limitazione freccia 1/200 della luce)RED values: serviceability limit states (deflection 1/200 span)
ITPH 55600 - 750 - 900
ST 4.L - REV. 1 - 11/2014 19
Tabelle portata ACCIAIO - STEEL load tables Tabelle portate ALLUMINIO - ALLUMINUM load tables
Sezione lorda ALLUMINIO - ALLUMINUM gross sectionSezione lorda ACCIAIO - STEEL gross sectionSpessore nominaleNominal thickness (mm)Peso nominale *Weight nominal (Kg./m2)
P
l
ITPH 75 - D570 (passo greche 190 mm)
JY (cm4/m)
(cm3/m)
(cm3/m)
(cm3/m)
We,inf
Wp
We,sup
0,50 0,60 0,70 0,80 1,00 1,20 0,60 0,70 0,80 1,00 1,20
Larghezza efficace appoggio: 50 mm
Working width support: 50 mm
3,50 3,75 4,00 4,25 4,50 4,75 5,00 5,25 5,50 5,75 6,002,00 2,50 3,00 3,25 3,50 3,75 4,00 4,25 4,50 4,75 5,00 5,25 5,50 5,75 6,002,00 2,50 3,00 3,25
3,50 3,75 4,00 4,25 4,50 4,75 5,00 5,25 5,50 5,75 6,002,00 2,50 3,00 3,25
3,50 3,75 4,00 4,25 4,50 4,75 5,00 5,25 5,50 5,75 6,002,00 2,50 3,00 3,25
3,50 3,75 4,00 4,25 4,50 4,75 5,00 5,25 5,50 5,75 6,002,00 2,50 3,00 3,25
3,50 3,75 4,00 4,25 4,50 4,75 5,00 5,25 5,50 5,75 6,002,00 2,50 3,00 3,25
l = m
P =
Kg.
/m2
Spessorenominale
mm
0,5
0,7
0,8
1,0
1,2
0,6
Nominalthickness
Larghezza efficace appoggio: 50 mm
Working width support: 50 mm
l = m
P =
Kg.
/m2
Spessorenominale
mm
0,5
0,7
0,8
1,0
1,2
0,6
Nominalthickness
Larghezza efficace appoggio: 50 mm
Working width support: 50 mm
l = m
P =
Kg.
/m2
Spessorenominale
mm
0,5
0,7
0,8
1,0
1,2
0,6
Nominalthickness
P P
l l
P P P
l l l
6,9 8,3 9,6 11,0 13,8 16,5
61,48
12,93
22,38
18,92
74,80
15,74
27,23
23,13
86,51
18,20
31,48
26,89
99,24
20,88
36,11
31,00
122,51
25,78
44,58
38,67
144,63
30,44
52,62
46,14
230 145
330 210
275430
555
780 495
725
350
1000
100
140 120 100
185 155
240 200 160
340 265 210
415 320 255
85 70 60 50
85
130 105
130 105 85
165 135 110
200 165 135
70 55
85 70 55
70 55
90
110
75 60 50
90 75 60 50
195 135 100
260 185 135
320
385
225 165
270 200
360520 260
330450650
90 80 70
120 105
145 125 110
170 150 135
225 200 175
290 255 225
60 55 50
90
100 90 80
120 105 95
155 140 125
200 180 160
80 75
70 65
85 75
115 105
145 130
65 60 55 50
60 55 50
70 65 60 55
95 85 80 70
120 105 95 90
235 165 125
310 220 165
270385 200
325465 240
320435625
405550790
110 95 85
145 125 115
175 155 135
210 185 165
280 245 220
355 310 275
75 70 60
100 90 80
120 110 100
145 130 120
195 175 155
245 220 200
55 50
75 65 60
90 80 70
105 95 85
145 130 110
180 155 135
50
60 50
75 60 55
95 80 70
115 95 85
16,27
28,14
77,32
23,92
88,98
32,38
18,72
27,66
101,70
37,01
21,40
31,78
126,19
45,92
26,56
39,85
148,20
2,8 3,3 3,8 4,7 5,7
53,92
31,19
47,30
170 100 55
225
280
115
140
100370 185
125225460
65
75 55
75 55
90 70 55
135 95
175 120 90
210 150 115
205290 150
255370 185
70 60 55
85 75 60
100 90
130 110 100
160 140 125
50
55
75 65 60
85 75
110 95
55
70 55
85 70 55
165 115 85 75 65
205 150 110
180255 135 115
245350
445
180 160
225310 195 150
55
95 80 65 50
95 75 60 50
125 100 80 65 50
120 95 75 60 50
* peso calcolato rispetto alla larghezza utile - weight calculated relevant to working width
Valori in BLU: stati limite ultimoCarichi variabili uniformemente distribuitiVariable uniformly distributed loads BLU values: ultimate limit states
Valori in ROSSO: stati limite di esercizio (limitazione freccia 1/200 della luce)RED values: serviceability limit states (deflection 1/200 span)
20 ST 4.L - REV. 1 - 11/2014
Tabelle portata ACCIAIO - STEEL load tables Tabelle portate ALLUMINIO - ALLUMINUM load tables
Sezione lorda ALLUMINIO - ALLUMINUM gross sectionSezione lorda ACCIAIO - STEEL gross sectionSpessore nominaleNominal thickness (mm)Peso nominale *Weight nominal (Kg./m2)
P
l
Valori in BLU: stati limite ultimoCarichi variabili uniformemente distribuitiVariable uniformly distributed loads BLU values: ultimate limit states
Valori in ROSSO: stati limite di esercizio (limitazione freccia 1/200 della luce)RED values: serviceability limit states (deflection 1/200 span)
JY (cm4/m)
(cm3/m)
(cm3/m)
(cm3/m)
We,inf
Wp
We,sup
0,50 0,60 0,70 0,80 1,00 1,20 0,60 0,70 0,80 1,00 1,20
Larghezza efficace appoggio: 50 mm
Working width support: 50 mm
3,50 3,75 4,00 4,25 4,50 4,75 5,00 5,25 5,50 5,75 6,002,00 2,50 3,00 3,25 3,50 3,75 4,00 4,25 4,50 4,75 5,00 5,25 5,50 5,75 6,002,00 2,50 3,00 3,25
3,50 3,75 4,00 4,25 4,50 4,75 5,00 5,25 5,50 5,75 6,002,00 2,50 3,00 3,25
3,50 3,75 4,00 4,25 4,50 4,75 5,00 5,25 5,50 5,75 6,002,00 2,50 3,00 3,25
3,50 3,75 4,00 4,25 4,50 4,75 5,00 5,25 5,50 5,75 6,002,00 2,50 3,00 3,25
3,50 3,75 4,00 4,25 4,50 4,75 5,00 5,25 5,50 5,75 6,002,00 2,50 3,00 3,25
l = m
P =
Kg.
/m2
Spessorenominale
mm
0,5
0,7
0,8
1,0
1,2
0,6
Nominalthickness
Larghezza efficace appoggio: 50 mm
Working width support: 50 mm
l = m
P =
Kg.
/m2
Spessorenominale
mm
0,5
0,7
0,8
1,0
1,2
0,6
Nominalthickness
Larghezza efficace appoggio: 50 mm
Working width support: 50 mm
l = m
P =
Kg.
/m2
Spessorenominale
mm
0,5
0,7
0,8
1,0
1,2
0,6
Nominalthickness
P P
l l
P P P
l l l
6,9 8,3 9,6 11,0 13,8 16,5 2,8 3,3 3,8 4,7 5,7
61,48
12,93
22,38
18,92
74,80
15,74
27,23
23,13
86,51
18,20
31,48
26,89
99,24
20,88
36,11
31,00
122,51
25,78
44,58
38,67
144,63
30,44
52,62
46,14
340 215
430 275
320500
580
745 475
580915
370
150 125
185 160
215 185
255 215
325 270
400 320
105 85
130 105
150 120
175 140
215 170
250 200
70 55
85 70 55
95 80 65
110 90 75
140 110 90
165 135 110
55
60 50
75 60 50
90 75 60 50
170 115 80 70
240 165 120 100
315
400
215 155 135
275 200 175
385555 280 245
375515745 325
60 55
90 80 70 60
115 100 90 80
150 135 115 105
215 190 165 150
285 250 225 200
55 50
70 65
95 85 75 70
135 120 110 100
180 160 145 130
55 50
60 55 50
90 80 75
120 110 100
205 140 100 90
290 200 145 125
260380 190 165
335480 245 215
340465670 300
400460625895
75 65
110 95 85 75
145 125 115 100
185 165 145 130
260 230 205 185
350 310 275 245
60 50
70 60
90 80 75 65
115 105 95 85
165 150 135 115
220 185 155 135
55 50
60 55 50
75 65 55
95 80 70
115 95 85
16,27
28,14
77,32
23,92
88,98
32,38
18,72
27,66
101,70
37,01
21,40
31,78
126,19
45,92
26,56
39,85
148,20
53,92
31,19
47,30
245 120 65 50
285
325
140 75 60
160 90 65 50
110405 200 80 65 50
130235475 95 75 55
120 80 55 50
155 105 75 65 55 50
200 135 95 85 70 65 55
205300 145 125 110 95 85
270390 195 170 150 130 115
50
75 65 60 50
100 85 70 55
145 100 70 60 55
190 130 95 80 70 60
165240 120 105 90 80
250360
465
180 155 135 105
240325 200 155 125
55
65 55
85 65 55
100 80 65 50
* peso calcolato rispetto alla larghezza utile - weight calculated relevant to working width
ITPH 75 - R570 (passo greche 190 mm)
ST 4.L - REV. 1 - 11/2014 21
Tabelle portata ACCIAIO - STEEL load tables Tabelle portate ALLUMINIO - ALLUMINUM load tables
Sezione lorda ALLUMINIO - ALLUMINUM gross sectionSezione lorda ACCIAIO - STEEL gross sectionSpessore nominaleNominal thickness (mm)Peso nominale *Weight nominal (Kg./m2)
P
l
Valori in BLU: stati limite ultimoCarichi variabili uniformemente distribuitiVariable uniformly distributed loads BLU values: ultimate limit states
Valori in ROSSO: stati limite di esercizio (limitazione freccia 1/200 della luce)RED values: serviceability limit states (deflection 1/200 span)
ITPH 75 - D820 (passo greche 273 mm)
JY (cm4/m)
(cm3/m)
(cm3/m)
(cm3/m)
We,inf
Wp
We,sup
0,50 0,60 0,70 0,80 1,00 1,20 0,60 0,70 0,80 1,00 1,20
Larghezza efficace appoggio: 50 mm
Working width support: 50 mm
3,25 3,50 3,75 4,00 4,25 4,50 4,75 5,00 5,25 5,50 6,002,00 2,50 2,75 3,00 3,50 3,75 4,00 4,25 4,50 4,75 5,00 5,25 5,25 5,50 6,002,00 2,50 3,00 3,25
3,50 3,75 4,00 4,25 4,50 4,75 5,00 5,25 5,50 5,75 6,002,00 2,50 3,00 3,25
3,50 3,75 4,00 4,25 4,50 4,75 5,00 5,25 5,00 5,50 6,002,00 2,50 3,00 3,25
3,50 3,75 4,00 4,25 4,50 4,75 5,00 5,25 5,50 5,75 6,002,00 2,50 3,00 3,25
3,50 3,75 4,00 4,25 4,50 4,75 5,00 5,25 5,50 5,75 6,002,00 2,50 3,00 3,25
l = m
P =
Kg.
/m2
Spessorenominale
mm
0,5
0,7
0,8
1,0
1,2
0,6
Nominalthickness
Larghezza efficace appoggio: 50 mm
Working width support: 50 mm
l = m
P =
Kg.
/m2
Spessorenominale
mm
0,5
0,7
0,8
1,0
1,2
0,6
Nominalthickness
Larghezza efficace appoggio: 50 mm
Working width support: 50 mm
l = m
P =
Kg.
/m2
Spessorenominale
mm
0,5
0,7
0,8
1,0
1,2
0,6
Nominalthickness
P P
l l
P P P
l l l
6,0 7,2 8,4 9,6 12,0 14,4 2,5 2,9 3,3 4,1 4,9
51,00
9,59
23,40
14,13
62,16
11,69
28,50
17,30
72,00
13,54
33,01
20,12
82,73
15,56
37,92
23,23
102,48
19,28
46,94
29,05
121,41
22,84
55,57
34,76
160 100
235 145 100 85
190305
390
575 365
610
245
130 110
170 140
250 210
345 270
70 55 50
140 100 75 65 55 50
70 60 50
185 135 100 85 75 70 60 55 50
165 120 90 80 70 60 55 50
230 165 125 110 95 85 75 70 60 55 50
95 80 70
120 105
175 140 110
210 170 135 110
55
85 65 55
90 75 60 50
285 200 150 130 115 105 90 85 6575 60 55 50
220 160 120 105 95 85 75 70 60 55 50
275 200 150 130 115 105 95 85 7075 65 55 50
385 275 205 180 160 140 125 110 90100 85 75 70 65 60
495 350 260 230 200 180 160 145 115130 105 95 90 80 75
340 245 185 160 145 125 115 105 8595 75 70 60 50
465 330 250 220 195 170 155 140 115125 105 90 80 65 55
600 425 325 280 245 220 195 180 145160 130 115 95 85 70
90 75 60 50
12,08
29,46
64,25
17,89
74,06
33,95
13,92
20,71
105,56
48,34
19,86
29,94
84,78
38,85
15,94
23,82
124,41
56,94
23,41
35,65
120 75
155
200
95 50
60110
80300 150 60
100190380 75 60
100 70 55
125 90 65 55 50
150 110 80 70
150210 110 100
195270 145 125 110
60 55 50
85 75 65 60 55
95 85 75 70 55
120 85 65
150 105 80
130180 100
185255
335
135
175235
55 50
70 60 50
85
125 105
155 125 105
75 60
85 65 55
85 65 55
1000
* peso calcolato rispetto alla larghezza utile - weight calculated relevant to working width
S i l d ACCIAIO STEEL
22 ST 4.L - REV. 1 - 11/2014
Tabelle portata ACCIAIO - STEEL load tables Tabelle portate ALLUMINIO - ALLUMINUM load tables
Sezione lorda ALLUMINIO - ALLUMINUM gross sectionSezione lorda ACCIAIO - STEEL gross sectionSpessore nominaleNominal thickness (mm)Peso nominale *Weight nominal (Kg./m2)
P
l
ITPH 75 - R820 (passo greche 273 mm)
JY (cm4/m)
(cm3/m)
(cm3/m)
(cm3/m)
We,inf
Wp
We,sup
0,50 0,60 0,70 0,80 1,00 1,20 0,60 0,70 0,80 1,00 1,20
Larghezza efficace appoggio: 50 mm
Working width support: 50 mm
3,50 3,75 4,00 4,25 4,50 4,75 5,00 5,25 5,50 5,75 6,002,00 2,50 3,00 3,25
3,50 3,75 4,00 4,25 4,50 4,75 5,00 5,25 5,50 5,75 6,002,00 2,50 3,00 3,25
3,50 3,75 4,00 4,25 4,50 4,75 5,00 5,25 5,50 5,75 6,002,00 2,50 3,00 3,25 3,50 3,75 4,00 4,25 4,50 4,75 5,00 5,25 5,50 5,75 6,002,00 2,50 3,00 3,25
3,50 3,75 4,00 4,25 4,50 4,75 5,00 5,25 5,50 5,75 6,002,00 2,50 3,00 3,25
3,50 3,75 4,00 4,25 4,50 4,75 5,00 5,25 5,50 5,75 6,002,00 2,50 3,00 3,25l = m
P =
Kg.
/m2
Spessorenominale
mm
0,5
0,7
0,8
1,0
1,2
0,6
Nominalthickness
Larghezza efficace appoggio: 50 mm
Working width support: 50 mm
l = m
P =
Kg.
/m2
Spessorenominale
mm
0,5
0,7
0,8
1,0
1,2
0,6
Nominalthickness
Larghezza efficace appoggio: 50 mm
Working width support: 50 mm
l = m
P =
Kg.
/m2
Spessorenominale
mm
0,5
0,7
0,8
1,0
1,2
0,6
Nominalthickness
P P
l l
P P P
l l l
6,0 7,2 8,4 9,6 12,0 14,4 2,5 2,9 3,3 4,1 4,9
51,00
9,59
23,40
14,12
62,16
11,69
28,50
17,27
72,00
13,54
33,01
20,09
82,73
15,56
37,92
23,18
102,48
19,28
46,94
28,95
121,41
22,84
55,57
34,16
265 180
365 230
435
510
655
805
275
325
415
510
125 105 85
160 135 105
190 160 125
220 180 145
285 225 180
345 270 210
70 55
85 70 55
100 80 65 55
115 90 75 60 50
140 115 95 75 60 50
170 135 110 90 75 60 50
115 80 55 50
165 115 80 70 60 55
220
280
150 110 95 80 70
195 140 120 105 90
275400 200 175 155 135
270370535 235 205 180
60 55 50
80 70 65 55 50
120 105 95 85 75 70 65 55
160 145 130 115 105 95 85 80
50
70
140 95 70 60
205 140 100 85
180265 130 115
235340 170 150
245335480 215
290330450645
50
75 65 60 50
100 90 75 70
130 115 100 90
190 165 150 130
255 225 200 180
60 55 50
80 70 65
120 105 95
160 145 130
60 55 50
90 80 70 60
110 95 80 70
12,08
29,46
64,25
17,86
74,06
33,95
13,92
20,67
84,78
38,85
15,94
23,76
105,56
48,34
19,86
29,83
124,41
56,94
23,41
35,01
55
70 50
80 60
180 100 55
230
270
115 65
70135
90340 165
105195400
80 55
105 70 50
140 95 65
140210 100
190280 140
55 50
85 75 65 55
120 105 90 80
50
70 60 55
100 65 50
130 90 65 55
115165 80 70
175250
335
125 110
170235 150
60 55
95 80
130 105
70 55
80 65 50
* peso calcolato rispetto alla larghezza utile - weight calculated relevant to working width
Valori in BLU: stati limite ultimoCarichi variabili uniformemente distribuitiVariable uniformly distributed loads BLU values: ultimate limit states
Valori in ROSSO: stati limite di esercizio (limitazione freccia 1/200 della luce)RED values: serviceability limit states (deflection 1/200 span)
ST 4.L - REV. 1 - 11/2014 23
ITPH 106 - D798 (passo greche 250 mm)
Tabelle portata ACCIAIO - STEEL load tables Tabelle portate ALLUMINIO - ALLUMINUM load tables
Sezione lorda ALLUMINIO - ALLUMINUM gross sectionSezione lorda ACCIAIO - STEEL gross sectionSpessore nominaleNominal thickness (mm)Peso nominale *Weight nominal (Kg./m2)
P
l
* peso calcolato rispetto alla larghezza utile - weight calculated relevant to working width
Valori in BLU: stati limite ultimoCarichi variabili uniformemente distribuitiVariable uniformly distributed loads BLU values: ultimate limit states
Valori in ROSSO: stati limite di esercizio (limitazione freccia 1/200 della luce)RED values: serviceability limit states (deflection 1/200 span)
JY (cm4/m)
(cm3/m)
(cm3/m)
(cm3/m)
We,inf
Wp
We,sup
0,50 0,60 0,70 0,80 1,00 1,20 0,60 0,70 0,80 1,00 1,20
Larghezza efficace appoggio: 50 mm
Working width support: 50 mm
3,50 3,75 4,00 4,25 4,50 4,75 5,00 5,25 5,50 5,75 6,002,00 2,50 3,00 3,25
3,50 3,75 4,00 4,25 4,50 4,75 5,00 5,25 5,50 5,75 6,002,00 2,50 3,00 3,25
3,50 3,75 4,00 4,25 4,50 4,75 5,00 5,25 5,50 5,75 6,002,00 2,50 3,00 3,25 3,50 3,75 4,00 4,25 4,50 4,75 5,00 5,25 5,50 5,75 6,002,00 2,50 3,00 3,25
3,50 3,75 4,00 4,25 4,50 4,75 5,00 5,25 5,50 5,75 6,002,00 2,50 3,00 3,25
3,50 3,75 4,00 4,25 4,50 4,75 5,00 5,25 5,50 5,75 6,002,00 2,50 3,00 3,25l = m
P =
Kg.
/m2
Spessorenominale
mm
0,5
0,7
0,8
1,0
1,2
0,6
Nominalthickness
Larghezza efficace appoggio: 50 mm
Working width support: 50 mm
l = m
P =
Kg.
/m2
Spessorenominale
mm
0,5
0,7
0,8
1,0
1,2
0,6
Nominalthickness
Larghezza efficace appoggio: 50 mm
Working width support: 50 mm
l = m
P =
Kg.
/m2
Spessorenominale
mm
0,5
0,7
0,8
1,0
1,2
0,6
Nominalthickness
P P
l l
P P P
l l l
6,5 7,9 9,2 10,5 13,1 15,7
110,88
27,55
16,86
25,51
135,19
33,59
20,56
31,23
156,67
38,92
23,83
36,34
180,12
44,74
27,40
41,95
223,31
55,46
33,97
52,45
264,80
65,75
40,29
62,72
465 290
595 370
450710
860
730
910
540
-
-
-
1000
1000
1000
195 165 140
250 210 180
305 255 220
370 310 265
500 420 360
625 530 450
120 100 85
155 130 115
185 160 140
230 195 160
310 250 205
370 300 245
75 60 50
95 75 60 50
110 90 75 60 50
130 105 90
165 135 115
200 165 135
70 60 50
95 75 65 50
115 95 80 65
380 235 160
510 320 215
630
765
395 270
480 325
635 435
520765
130 110 95
180 150 130
225 190 165
275 235 200
365 310 270
440 375 325
80 70 60
110 8595
140 120 105
175 150 130
230 205 180
280 245 215
50
70 65
8095
115 100
155 140
190 170
55 50
70 65 55 50
8090 70 65
90125 110 100
150 135 120 110
485 300 205
645 405 275
500795 340
610965 415
550805
960 660
170 145 120
230 195 165
285 245 210
350 300 255
465 395 340
555 475 410
105 90 80
145 125 110
180 160 140
220 195 170
295 260 230
355 315 275
70 60 50
8595 75
120 105
150 135 120
205 180 160
245 220 195
65 60 50
8595 75 65
105 8595
145 130 115
175 160 140
34,72
21,26
139,77
32,29
161,18
24,52
40,04
37,39
184,62
28,08
45,86
43,01
230,11
35,01
57,14
54,06
271,44
2,7 3,2 3,6 4,5 5,4
41,30
67,39
64,32
360 215 115
420
490
250 135
155290
200645 365
235435795
85 60
100 75 55
115 90 65 50
150 115 85 65
180 135 105 80 60
50
275 170 110
345 210 140
420 260 175
365580 245
460735 310
90 75 60
115 95 80
145 120 100
205 170 145
260 220 190
50
70 60 50
85 75 65
125 110 95
160 140 120
55
80 70 60 55
105 95 80 70 60
350 215 145 120 100
435 270 180 150 125
330530 225 185 155
460735
925
310 260 220
395580 335 285
85 70 60 50
105 90 80 65 50
135 115 95 75 60
190 150 120 95 80 65 50
230 180 145 120 95 75 60 50
24 ST 4.L - REV. 1 - 11/2014
Tabelle portata ACCIAIO - STEEL load tables Tabelle portate ALLUMINIO - ALLUMINUM load tables
Sezione lorda ALLUMINIO - ALLUMINUM gross sectionSezione lorda ACCIAIO - STEEL gross sectionSpessore nominaleNominal thickness (mm)Peso nominale *Weight nominal (Kg./m2)
P
l
Valori in BLU: stati limite ultimoCarichi variabili uniformemente distribuitiVariable uniformly distributed loads BLU values: ultimate limit states
Valori in ROSSO: stati limite di esercizio (limitazione freccia 1/200 della luce)RED values: serviceability limit states (deflection 1/200 span)
* peso calcolato rispetto alla larghezza utile - weight calculated relevant to working width
JY (cm4/m)
(cm3/m)
(cm3/m)
(cm3/m)
We,inf
Wp
We,sup
0,50 0,60 0,70 0,80 1,00 1,20 0,60 0,70 0,80 1,00 1,20
Larghezza efficace appoggio: 50 mm
Working width support: 50 mm
3,50 3,75 4,00 4,25 4,50 4,75 5,00 5,25 5,50 5,75 6,002,00 2,50 3,00 3,25
3,50 3,75 4,00 4,25 4,50 4,75 5,00 5,25 5,50 5,75 6,002,00 2,50 3,00 3,25
3,50 3,75 4,00 4,25 4,50 4,75 5,00 5,25 5,50 5,75 6,002,00 2,50 3,00 3,25 3,50 3,75 4,00 4,25 4,50 4,75 5,00 5,25 5,50 5,75 6,002,00 2,50 3,00 3,25
3,50 3,75 4,00 4,25 4,50 4,75 5,00 5,25 5,50 5,75 6,002,00 2,50 3,00 3,25
3,50 3,75 4,00 4,25 4,50 4,75 5,00 5,25 5,50 5,75 6,002,00 2,50 3,00 3,25l = m
P =
Kg.
/m2
Spessorenominale
mm
0,5
0,7
0,8
1,0
1,2
0,6
Nominalthickness
Larghezza efficace appoggio: 50 mm
Working width support: 50 mm
l = m
P =
Kg.
/m2
Spessorenominale
mm
0,5
0,7
0,8
1,0
1,2
0,6
Nominalthickness
Larghezza efficace appoggio: 50 mm
Working width support: 50 mm
l = m
P =
Kg.
/m2
Spessorenominale
mm
0,5
0,7
0,8
1,0
1,2
0,6
Nominalthickness
P P
l l
P P P
l l l
6,5 7,9 9,2 10,5 13,1 15,7
110,73
16,83
27,55
25,50
135,00
20,51
33,59
31,22
156,44
23,77
38,93
36,32
179,83
27,32
44,76
41,94
222,93
33,87
55,49
52,43
264,30
40,15
65,79
62,71
395 245
530 330
410655
790
655
500
-
-
-
1000
1000
1000
1000
1000
165 135 115
220 185 155
280 235 200
340 285 240
445 375 320
755 585 470
95 85 70
135 115 100
170 145 125
210 180 155
275 240 200
375 300 245
60 50
85 70 55
105 85 70 55
125 100 85
165 135 110
205 165 140
70 55
95 75 65 50
120 95 80 65
400 260 180
515 335 235
620
765
405 285
505 355
650 460
575815
150 130 110
200 170 150
240 210 180
300 255 220
390 335 295
490 425 370
95 85 75
130 115 100
160 140 120
190 165 145
255 225 200
325 285 255
65 55 50
90 80
110 95
130 115
180 160
225 205
70 60 55 50
85 75 70 60
105 95 85 75
145 130 115 105
185 165 150 135
505 330 230
650 425 300
515780
965
360
635 450
580820
725
195 165 145
255 220 190
310 265 230
380 325 280
495 430 375
620 535 470
125 110 95
165 145 130
205 180 160
245 215 190
330 290 260
415 365 325
85 75 70
115 105 90
140 125 115
170 150 135
230 205 185
290 260 235
60
80 75 65
100 90 80
120 110 95
170 145 125
55 50
210 180 155
21,21
34,73
139,57
32,28
160,94
40,05
24,45
37,38
184,33
45,87
28,01
42,99
229,70
57,17
34,90
54,04
270,91
2,7 3,2 3,6 4,5 5,4
67,44
41,15
64,30
285 175 100
355
440
220 120
140265
190605 345
230425760
70 55
90 65 50
105 80 60
140 105 80 60
175 135 100 80 60
290 185 125
350 225 155
415 270 185
360550 250
445685 310
105 90 75
130 110 95
155 135 115
210 180 155
265 225 195
65 55 50
80 70 60 50
100 85 75
135 120 105
170 150 130
65 55 50
90 80 70 55
115 105 85 70 55
370 240 165 140 120
445 285 200 170 145
340525 240 200 175
455695
860
320 270 230
395565 340 280
95 75 60
115 90 70 55
140 110 85 70 55
185 145 115 95 75 60
225 180 145 115 95 75 60 50
ITPH 106 - R798 (passo greche 250 mm)
ST 4.L - REV. 1 - 11/2014 25
Tabelle portata ACCIAIO - STEEL load tables Tabelle portate ALLUMINIO - ALLUMINUM load tables
Sezione lorda ALLUMINIO - ALLUMINUM gross sectionSezione lorda ACCIAIO - STEEL gross sectionSpessore nominaleNominal thickness (mm)Peso nominale *Weight nominal (Kg./m2)
P
l
* peso calcolato rispetto alla larghezza utile - weight calculated relevant to working width
Valori in BLU: stati limite ultimoCarichi variabili uniformemente distribuitiVariable uniformly distributed loads BLU values: ultimate limit states
Valori in ROSSO: stati limite di esercizio (limitazione freccia 1/200 della luce)RED values: serviceability limit states (deflection 1/200 span)
ITPH 106 - D1040 (passo greche 333 mm)
JY (cm4/m)
(cm3/m)
(cm3/m)
(cm3/m)
We,inf
Wp
We,sup
0,50 0,60 0,70 0,80 1,00 1,20 0,60 0,70 0,80 1,00 1,20
Larghezza efficace appoggio: 50 mm
Working width support: 50 mm
3,50 3,75 4,00 4,25 4,50 4,75 5,00 5,25 5,50 5,75 6,002,00 2,50 3,00 3,25
3,50 3,75 4,00 4,25 4,50 4,75 5,00 5,25 5,50 5,75 6,002,00 2,50 3,00 3,25
3,50 3,75 4,00 4,25 4,50 4,75 5,00 5,25 5,50 5,75 6,002,00 2,50 3,00 3,25 3,50 3,75 4,00 4,25 4,50 4,75 5,00 5,25 5,50 5,75 6,002,00 2,50 3,00 3,25
3,50 3,75 4,00 4,25 4,50 4,75 5,00 5,25 5,50 5,75 6,002,00 2,50 3,00 3,25
3,50 3,75 4,00 4,25 4,50 4,75 5,00 5,25 5,50 5,75 6,002,00 2,50 3,00 3,25l = m
P =
Kg.
/m2
Spessorenominale
mm
0,5
0,7
0,8
1,0
1,2
0,6
Nominalthickness
Larghezza efficace appoggio: 50 mm
Working width support: 50 mm
l = m
P =
Kg.
/m2
Spessorenominale
mm
0,5
0,7
0,8
1,0
1,2
0,6
Nominalthickness
Larghezza efficace appoggio: 50 mm
Working width support: 50 mm
l = m
P =
Kg.
/m2
Spessorenominale
mm
0,5
0,7
0,8
1,0
1,2
0,6
Nominalthickness
P P
l l
P P P
l l l
5,9 7,1 8,2 9,4 11,8 14,1
98,43
29,28
13,60
21,57
120,16
35,74
16,60
26,42
139,40
41,46
19,26
30,76
160,45
47,71
22,17
35,53
199,40
59,27
27,56
44,47
237,03
70,43
32,76
53,24
360 225
475 300
365585
705
925 585
725
445
-
1000
1000
150 125 105
200 170 140
250 210 175
300 255 215
400 335 285
495 420 355
90 75 65
120 105 90
150 130 115
185 160 140
245 215 180
305 265 220
55 50
80 65 55
100 80 65 50
115 95 75
150 120 100
180 150 120
65 50
85 70 55
100 85 70 60
300 185 120
400 250 165
500
610
310 210
380 260
510810
975
345
420615
100 85 70
140 115 100
175 150 125
215 185 155
290 250 215
350 300 260
60 50
85 75 65
110 95 80
135 115 100
185 160 140
225 195 170
55
70 60
90 80
125 110
150 135
55
70 60 55 50
95 85 75 70
120 105 95 85
380 235 160
505 315 215
395630 265
485765 330
440645
775 530
130 110 95
180 150 130
225 190 165
275 235 200
370 315 275
445 380 330
80 70 60
110 95 85
140 120 105
175 150 135
235 205 180
285 250 220
50
75 65 55
95 80 75
115 105 90
160 145 125
195 175 155
50
65 55 50
80 75 65
115 100 90
140 125 110
36,95
17,16
124,23
27,32
143,42
19,82
42,65
31,65
164,47
22,73
48,90
36,42
205,48
28,40
61,07
45,84
242,97
2,4 2,8 3,2 4,1 4,9
33,59
72,19
54,60
305 190 100
365
430
220 120
140255
175560 325
210385680
75 55
90 65 50
105 80 60
135 100 75 60
160 120 95 70 55
215 130 85
270 165 105
330 205 135
285460 190
365585 245
70 55
90 75 60
110 95 80
160 135 115
205 175 145
50
65 55
95 85 70
125 110 95
60 55
80 70 60 55
275 165 110 90 75
340 210 140 115 95
260420 175 145 120
365580
740
245 205 175
315465 265 225
65 55
80 70 60 50
105 90 75 65 50
150 125 110 85 70 55
190 160 130 105 85 70 55
26 ST 4.L - REV. 1 - 11/2014
Tabelle portata ACCIAIO - STEEL load tables Tabelle portate ALLUMINIO - ALLUMINUM load tables
Sezione lorda ALLUMINIO - ALLUMINUM gross sectionSezione lorda ACCIAIO - STEEL gross sectionSpessore nominaleNominal thickness (mm)Peso nominale *Weight nominal (Kg./m2)
P
l
* peso calcolato rispetto alla larghezza utile - weight calculated relevant to working width
Valori in BLU: stati limite ultimoCarichi variabili uniformemente distribuitiVariable uniformly distributed loads BLU values: ultimate limit states
Valori in ROSSO: stati limite di esercizio (limitazione freccia 1/200 della luce)RED values: serviceability limit states (deflection 1/200 span)
JY (cm4/m)
(cm3/m)
(cm3/m)
(cm3/m)
We,inf
Wp
We,sup
0,50 0,60 0,70 0,80 1,00 1,20 0,60 0,70 0,80 1,00 1,20
Larghezza efficace appoggio: 50 mm
Working width support: 50 mm
3,50 3,75 4,00 4,25 4,50 4,75 5,00 5,25 5,50 5,75 6,002,00 2,50 3,00 3,25
3,50 3,75 4,00 4,25 4,50 4,75 5,00 5,25 5,50 5,75 6,002,00 2,50 3,00 3,25
3,50 3,75 4,00 4,25 4,50 4,75 5,00 5,25 5,50 5,75 6,002,00 2,50 3,00 3,25 3,50 3,75 4,00 4,25 4,50 4,75 5,00 5,25 5,50 5,75 6,002,00 2,50 3,00 3,25
3,50 3,75 4,00 4,25 4,50 4,75 5,00 5,25 5,50 5,75 6,002,00 2,50 3,00 3,25
3,50 3,75 4,00 4,25 4,50 4,75 5,00 5,25 5,50 5,75 6,002,00 2,50 3,00 3,25l = m
P =
Kg.
/m2
Spessorenominale
mm
0,5
0,7
0,8
1,0
1,2
0,6
Nominalthickness
Larghezza efficace appoggio: 50 mm
Working width support: 50 mm
l = m
P =
Kg.
/m2
Spessorenominale
mm
0,5
0,7
0,8
1,0
1,2
0,6
Nominalthickness
Larghezza efficace appoggio: 50 mm
Working width support: 50 mm
l = m
P =
Kg.
/m2
Spessorenominale
mm
0,5
0,7
0,8
1,0
1,2
0,6
Nominalthickness
P P
l l
P P P
l l l
5,9 7,1 8,2 9,4 11,8 14,1
98,28
13,57
29,28
21,54
119,96
16,56
35,73
26,38
139,15
19,21
41,45
30,70
160,14
22,11
47,70
35,46
198,98
27,47
59,27
44,37
236,46
32,65
70,43
53,11
305 190
415 260
325515
635
530840
400
1000 1000
1000
125 105 85
175 145 120
220 180 155
270 225 190
360 305 260
675 525 415
75 60 55
105 90 75
130 115 100
165 140 125
220 190 165
330 265 220
65 55 50
85 75 60 50
105 90 75
145 120 100
180 145 120
60 50
80 70 55
100 85 70 55
275 180 125
370 240 170
455
555
300 210
370 260
495740
920
350
440615
105 90 75
145 125 105
180 155 135
225 195 170
300 260 225
380 325 285
65 55
90 80 70
120 105 90
145 130 115
195 175 155
250 220 195
60 55 50
50
80 70
100 90
135 120
175 155
65 55 50
80 70 65 55
110 100 90 80
140 125 115 105
350 230 160
465 310 215
380575 270
465700
930
330
445625
775 555
135 115 100
185 160 140
230 200 175
285 245 215
380 330 290
480 415 365
85 75 65
120 105 95
155 135 120
190 165 150
255 225 200
320 285 250
60 50
85 75 65
105 95 85
130 120 105
175 160 145
225 205 185
60 50
75 70 60
95 85 75
130 115 105
165 150 135
17,12
36,94
124,02
27,28
143,16
42,64
19,77
31,59
164,15
48,89
22,66
36,35
205,03
61,07
28,31
45,73
242,38
2,4 2,8 3,2 4,1 4,9
72,19
33,47
54,46
220 135 85
275
345
170 105
125210
165485 300
205380615
60
75 55
95 70 50
125 95 70 55
155 120 90 70 50
235 150 105
280 180 125
330 215 150
285435 200
350530 250
85 75 65 55
105 90 75
125 110 95
170 145 125
210 180 155
65 55 50
80 70 60 55
110 95 85
135 120 105
75 65 55 50
95 80 75 60
295 195 135 115 95
355 230 160 135 120
275415 195 165 140
360545
670
255 220 190
315445 270 235
85 65 50
100 80 65 50
120 95 75 60
160 130 105 80 65 50
200 160 125 100 80 65 55
ITPH 106 - R1040 (passo greche 333 mm)
ST 4.L - REV. 1 - 11/2014 27
Passo greche - Ribs step 600 mm - 5 Greche - RibsPasso greche - Ribs step 750 mm - 6 Greche - RibsPasso greche - Ribs step 900 mm - 7 Greche - Ribs
Materiali per solai collaboranti / Materials for collaborating floor
Sequenze montaggio - Assembly sequenceLamiera di acciaioSteel sheet
CalcestruttoConcrete
Posa lamiere e fissaggio con viti alle travi di sostegno(opzionale rivettatura delle greche di sormonto a passo 1 metro) / Assembling trapezoidal sheets and fixing with screws to supporting beams(as options use rivets on the overlapping ribs at one meter step).
Le lamiere vanno accostatetesta - testa / Trapezoidalsheets will be assembledhead to head.
appoggio in acciaio o calcestruzzo /steel or concrete support
l bs � ≥ 50 mml bc � ≥ 75 mm
l bs � ≥ 70 mml bc � ≥ 100 mm
appoggio in altro materiale /other material support
CalcestruzzoConcrete
H Non puntellate/Un-supported Puntellate/SupportedA **
cm 0,2 % ARete elettrosaldataAnti-crack mesh
Rete elettrosaldataAnti-crack mesh
0,4 % Acm2/m
10 0,9 Ø5 (200 X 200) 1,8
2,2
2,6
450
550
650
Tipo - Type S280GD UNI EN 10346
Spessore - Thickness*
Spessore - Thickness
Classe - Class
Par. 4.3.6.5.1 NTC/2008
Sezione minima rete elettrosaldata di ripartizione (a 20 mm dall’estradosso della soletta)Minimun section detailed rebars and anti-crack mesh (at 20 mm from top slab)
* Lo spessore delle lamiere grecate non deve essere inferiore a 0,80 mm;lo spessore potrà essere ridotto a 0,70 mm quando, in fase costruttiva,vengano studiati idonei provvedimenti atti a consentire il transito insicurezza di mezzi e persone / The thickness of trapezoidal sheets usedfor composite floor cannot be less than 0,80 mm; the thickness could bereduced to 0,70mm in case, during installation, suitable actions will betaken in order to allow the safe passage of means and people.
Se necessario puntellare la lamiere per aumentare il numero di appoggi In order to increase the number of supports, if necessary, put additionalsupports under the trapezoidal sheets.
Getto di calcestruzzo in corrispondenza degli appoggi e successivadistribuzione su tutta la superficie / Concrete casting in correspondenceof supports and consequent distribution on the whole surface.
Posa della rete elettrosaldata a 20 mm dall’estradosso(la rete va sormontata con idonee sovrapposizioni) / Assembling of theanti-crack mesh at 20 mm from top slab. (the anti-crack mesh is assembled with suitable overlapping )
** Sezione trasversale della soletta di calcestruzzo sopra le nervatureCross-wise section of the composite floor above ribs.
C25/30 D.M. 14/01/2008
hc � ≥ 40 mm
bm/ 3 = 24,3 mm
0,4 * hcDiametro inerteDiameter concrete
�
11
12
1,1
1,3
Ø6 (150 X 150)
Ø6 (100 X 100)
Ø6 (100 X 100)
Ø6 (200 X 200)
Ø6 (200 X 200)
l bs
l bc
l bs
l bs
ITP H55 - BETON600/750/900
bm=73
RETE ELETTROSALDATA - ANTI CRACK MESH
Hhc
55
150
39
20
≥
a) b)
Lamiere grecate collaboranti profilo ITPH55 marcate CE in accordo alla EN 1090 -1 Classe EXC3 da utilizzare in solai collaboranti acciaio - calcestruzzo
Collaborating trapezoidal steel sheetsITP H55 Beton profile CE marked according to EN 1090-1 EXC3 class to be used for composite floor steel - concrete.
28 ST 4.L - REV. 1 - 11/2014
Materiali per solai collaboranti / Materials for collaborating floor
Sequenze montaggio - Assembly sequenceLamiera di acciaioSteel sheet
CalcestruttoConcrete
Posa lamiere e fissaggio con viti alle travi di sostegno(opzionale rivettatura delle greche di sormonto a passo 1 metro) / Assembling trapezoidal sheets and fixing with screws to supporting beams(as options use rivets on the overlapping ribs at one meter step).
Le lamiere vanno accostatetesta - testa / Trapezoidalsheets will be assembledhead to head.
appoggio in acciaio o calcestruzzo /steel or concrete support
l bs � ≥ 50 mml bc � ≥ 75 mm
l bs � ≥ 70 mml bc � ≥ 100 mm
appoggio in altro materiale /other material support
CalcestruzzoConcrete
H Non puntellate/Un-supported Puntellate/SupportedA **
cm 0,2 % ARete elettrosaldataAnti-crack mesh
Rete elettrosaldataAnti-crack mesh
0,4 % Acm2/m
12 0,9 Ø 5 (200 X 200) 1,8
2,2
2,6
450
550
650
Tipo - Type S280GD UNI EN 10346
Spessore - Thickness*
Spessore - Thickness
Classe - Class
Par. 4.3.6.5.1 NTC/2008
Sezione minima rete elettrosaldata di ripartizione (a 20 mm dall’estradosso della soletta)Minimun section detailed rebars and anti-crack mesh (at 20 mm from top slab)
* Lo spessore delle lamiere grecate non deve essere inferiore a 0,80 mm;lo spessore potrà essere ridotto a 0,70 mm quando, in fase costruttiva,vengano studiati idonei provvedimenti atti a consentire il transito insicurezza di mezzi e persone / The thickness of trapezoidal sheets usedfor composite floor cannot be less than 0,80 mm; the thickness could bereduced to 0,70mm in case, during installation, suitable actions will betaken in order to allow the safe passage of means and people.
Se necessario puntellare la lamiere per aumentare il numero di appoggi /In order to increase the number of supports, if necessary, put additionalsupports under the trapezoidal sheets.
Getto di calcestruzzo in corrispondenza degli appoggi e successivadistribuzione su tutta la superficie / Concrete casting in correspondenceof supports and consequent distribution on the whole surface.
Posa della rete elettrosaldata a 20 mm dall’estradosso(la rete va sormontata con idonee sovrapposizioni) / Assembling of theanti-crack mesh at 20 mm from top slab. (the anti-crack mesh is assembled with suitable overlapping )
** Sezione trasversale della soletta di calcestruzzo sopra le nervature /Cross-wise section of the composite floor above ribs.
C25/30 D.M. 14/01/2008
hc � ≥ 40 mm
bm/ 3 = 17,16 mm
0,4 * hcDiametro inerteDiameter concrete
�
13
14
1,1
1,3
Ø 6 (150 X 150)
Ø 6 (100 X 100)
Ø 6 (100 X 100)
Ø 6 (200 X 200)
Ø 6 (200 X 200)
3,075015 1,5 Ø 8 (150 X 150)Ø 6 (200 X 200)
l bs
l bc
l bs
l bs
ITP H75 - BETON570 (passo greche / ribs step 190 mm)
RETE ELETTROSALDATA - ANTI CRACK MESH
H
hc
75
20
bm=51,5570
190
≥
a) b)
Lamiere grecate collaboranti profilo ITPH75 marcate CE in accordo alla EN 1090-1 Classe EXC3 da utilizzare in solai collaboranti acciaio - calcestruzzo
Collaborating trapezoidal steel sheets ITP H75 Beton profile CE marked according to EN 1090-1 EXC3 class to be used for composite floor steel - concrete.
ST 4.L - REV. 1 - 11/2014 29
q
�
�
�
�
ITP H 55 - BETON600 - 750 - 900
Tabelle portata ACCIAIO - STEEL load tables
Sezione lorda ACCIAIO - STEEL gross sectionSpessore nominaleNominal thickness (mm)Peso nominale *Weight nominal (Kg./m2)
P
l
P
l
P
l
Acciaio zincato / Galvanized steelS280 GD - UNI EN 10346
Limite di freccia 20 mm o L = 1 /180 della luceServiceability limit states 20 mm or L = 1/180 span
Marcatura CE in accordo EN 1090-1 classe EXC3CE mark according to EN 1090-1 EXC3 class
JY (cm4/m)
(cm3/m)
(cm3/m)
(cm3/m)
We,inf
Wp
We,sup
0,70 0,80 1,00 1,20 1,50
Larghezza efficace appoggio: 50 mm
Working width support: 50 mm
2,50 2,75 3,00 3,25 3,50 3,75 4,00 4,25 4,50 4,75 5,001,751,50 2,00 2,25l = m
P =
Kg.
/m2
Spessorenominale
mm
0,70
1,00
1,20
1,50
0,80
Nominalthickness
47,01
17,09
17,09
19,70
53,57
19,48
19,48
22,56
66,96
24,35
24,35
28,46
79,74
28,99
28,99
34,22
98,57
35,91
35,91
43,02
9,2 10,5 13,1 15,7 19,6
782 572 432 337
693943 528 393 329
1295 734 562 440 352960
1298 1248 670 517 414 342917
1301 1301 1161 640 508 410 347843
Larghezza efficace appoggio: 50 mm
Working width support: 50 mm
2,50 2,75 3,00 3,25 3,50 3,75 4,00 4,25 4,50 4,75 5,001,751,50 2,00 2,25l = m
P =
Kg.
/m2
Spessorenominale
mm
0,70
1,00
1,20
1,50
0,80
Nominalthickness
512 402 322
493628 398 328
565700895 465 390 330
1183 618748928 518 438 393 338
1301 1301 1051 726866 621 556 481 419 360
595 514 448 391
Larghezza efficace appoggio: 50 mm
Working width support: 50 mm
2,50 2,75 3,00 3,25 3,50 3,75 4,00 4,25 4,50 4,75 5,001,751,50 2,00 2,25l = m
P =
Kg.
/m2
Spessorenominale
mm
0,70
1,00
1,20
1,50
0,80
Nominalthickness
542 427 347
523668 423 348
605745 495 415 355 305950
1258 658798 553 473 418 360988
1301 1301 1121 661926 776
* peso calcolato rispetto alla larghezza utile - weight calculated relevant to working width
Valori in BLU: stati limite ultimoCarichi variabili uniformemente distribuitiVariable uniformly distributed loads BLU values: ultimate limit states
Valori in ROSSO: Limite di freccia 20 mm o L = 1 /180 della luceRED values: serviceability limit states 20 mm or L = 1/180 span
30 ST 4.L - REV. 1 - 11/2014
q
q = carico di esercizio variabile / service variable loadl
TABELLE PORTATE - LOAD TABLE
I valori delle tabelle sono stati determinati considerando coefficienti di combinazioni delle azioni variabili come previsto dalle NTC 08 per edifici di categoria D(ambiente ad uso commerciale). Il contenuto delle tabelle è da considerarsi con semplice valore indicativo. E’ competenza del progettista calcolare per ognisingolo caso i relativi valori. The table values have been calculated considering combination coefficient of variable actions as expected by NTC 08 for Dcategory building (commercial use building). The table content is to be considered as indicative: it’s competence of designer to calculate, for every single case,the relative values.
Carico permanente / permanent load p = 0,00 KN/m2
(il carico permanente comprende il peso di pavimentazione, sottofondo e impianti fissi) (the permanent load includes floor weight, subgrade and fixed equipmentes)
• rottura cilindrica / cylinder break fck = 25 N/mm2
• soletta con calcestruzzo normale / composite floor with normal concrete
Resistenza al taglio longitudinale: metodo di “interazione parziale” / Longitudinal shear resistance: method of partial interaction
Per lo S.L.S. elemento appoggiato limitazione 1/300 della freccia - For S.L.S. supported element deflection 1/300 span
Acciaio zincato / Galvanized steelS280 GD - UNI EN 10346
ITPH 55 BETON600/750 / 900
0,7 2,25 2,00 2,00
2,50 2,25 2,25
2,75 2,75 3,00
3,00 3,25 3,25
3,25 3,75 3,75
185,1
186,1
188,3
190,4
193,8
0,8
1,0
1,2
1,5
HSpessoresoletta
/Thicknesscomposite
floor
SSpessorelamiera
/Steel
thickness
Luce massima infase di getto /
Max span during concrete casting
m
Pesosoletta
/Weight
compositefloor
2 app 3 app 4 appmm
100mm
�0,091N/mm2
�τu, Rd = determinato con Rapporto di Prova N ° 306239: prova di carico su solaio in calcestruzzo secondo il D.M. 14/01/2008 e la norma UNI EN 1994-1-1:2005 e relazionetecnica N° 309245 - Valutazione della resistenza al taglio longitudinale di progetto di solette composte con lamiere grecate / Calculated with test report N° 306239:load test on concrete floor according to D.M. 14/01/2008 and norm UNI EN 1994-1-1:2005 and technical report N° 309245 - valuation of design longitudinal shear ofconcrete composite floor with trapezoidal steel sheet.
Kg./m2
Larghezza efficace appoggio: 50 mm
Working width support: 50 mm
l=m
q =
Kg.
/m2
q =
Kg.
/m2
1,50 1,75 2,00 2,25 2,50 2,75 3,00 3,25 3,50 3,75 4,00 4,25 4,50 4,75 5,00 5,25 5,50 5,75 6,00
2170 1835 1585 1385 1230 1105 930 780 650 565 485 420 360
2200 1860 1605 1405 1145 940 780 655 555 475 405 350 300
2215 1875 1570 1240 1000 820 680 570 480 410 350 300 260
2235 1720 1320 1045 845 690 575 480 405 345 295 250 215
2105 1560 1200 950 765 630 520 435 370 310 265 225 190
0,7
0,8
1,0
1,2
1,5
2 app 3 app 4 appmm
110mm
0,091N/mm2
Kg./m2 l=m 1,50 1,75 2,00 2,25 2,50 2,75 3,00 3,25 3,50 3,75 4,00 4,25 4,50 4,75 5,00 5,25 5,50 5,75 6,00
0,7
0,8
1,0
1,2
1,5
2 app 3 app 4 appmm
120mm
�0,091N/mm2
Kg./m2 l=m 1,50 1,75 2,00 2,25 2,50 2,75 3,00 3,25 3,50 3,75 4,00 4,25 4,50 4,75 5,00 5,25 5,50 5,75 6,00
0,7
0,8
1,0
1,2
1,5
2 app 3 app 4 appmm
130mm
�0,091N/mm2
Kg./m2 l=m 1,50 1,75 2,00 2,25 2,50 2,75 3,00 3,25 3,50 3,75 4,00 4,25 4,50 4,75 5,00 5,25 5,50 5,75 6,00
2,25 2,00 2,00
2,25 2,25 2,25
2,75 2,75 2,75
2,75 3,25 3,25
3,00 3,75 3,75
209,6
210,6
212,8
214,9
218,3 2470 2090 1805 1580 1405 1190 990 835 705 605 520 450 390 335 300
2505 2120 1830 1515 1225 1005 835 705 595 510 440 375 325 280 245
2525 2135 1680 1325 1075 880 735 620 525 445 380 330 285 245 210
2495 1850 1425 1130 915 750 625 525 445 380 325 275 235 205 175
2265 1685 1300 1030 835 685 570 480 405 345 295 250 215 180 155
2,00 1,75 1,75
2,25 2,00 2,25
2,50 2,50 2,75
2,75 3,00 3,00
3,00 3,50 3,75
234,1
235,1
237,3
239,4
242,8
q =
Kg.
/m2
2775 2345 2025 1780 1520 1260 1055 890 755 645 555 480 420 365 320
2810 2375 2035 1610 1300 1070 895 755 640 545 475 410 350 305 265 230 195
275 235
2830 2320 1785 1415 1145 950 790 665 565 480 415 355 305 265 235
2670 1980 1530 1215 990 810 675 575 485 410 355 300 265 225 190 160 140
195 165
2430 1810 1400 1115 905 745 625 530 445 375 320 275 235 200 170 145 120
2,00 1,75 1,75
2,25 2,00 2,00
2,50 2,50 2,50
2,75 3,00 3,00
3,00 3,50 3,50
258,6
259,6
261,8
263,9
267,3
q =
Kg.
/m2
3000 2600 2245 1960 1600 1330 1110 935 795 685 590 510 440 385 335
3000 2635 2130 1705 1380 1135 950 800 680 585 500 435 375 325 280 245 210 180
220290 255
3000 2460 1900 1505 1220 1010 840 710 605 515 445 380 330 285 245
2835 2110 1635 1300 1055 870 730 615 520 445 380 325 280 240 205 170 150 125
210 180 155
2600 1940 1505 1200 975 805 670 565 480 410 350 300 255 220 185 160 135 110
τu, Rd
τu, Rd
τu, Rd
τu, Rd
ST 4.L - REV. 1 - 11/2014 31
ITP H 75 - BETON570
Tabelle portata ACCIAIO - STEEL load tables
Sezione lorda ACCIAIO - STEEL gross sectionSpessore nominaleNominal thickness (mm)Peso nominale *Weight nominal (Kg./m2)
P
l
P
l
P
l
Acciaio zincato / Galvanized steelS280 GD - UNI EN 10346
Limite di freccia 20 mm o L = 1 /180 della luceServiceability limit states 20 mm or L = 1/180 span
Marcatura CE in accordo EN 1090-1 classe EXC3CE mark according to EN 1090-1 EXC3 class
JY (cm4/m)
(cm3/m)
(cm3/m)
(cm3/m)
We,inf
Wp
We,sup
0,70 0,80 1,00 1,20 1,50
Larghezza efficace appoggio: 50 mm
Working width support: 50 mm
2,50 2,75 3,00 3,25 3,50 3,75 4,00 4,25 4,50 4,75 5,001,751,50 2,00 2,25l = m
P =
Kg.
/m2
Spessorenominale
mm
0,70
1,00
1,20
1,50
0,80
Nominalthickness
20,7
81,65
17,35
29,22
25,50
92,96
19,76
33,27
29,18
116,00
24,65
41,50
36,80
137,90
29,31
49,33
44,22
173,18
36,82
61,94
56,49
9,6 11,0 13,8 16,5
998 768 583 458 368 303
1209 884 674 529 429 349 294
1282 1152 882 692 557 462 377 302
1284 1284 1089 859 694 564 479 406 349
1288 1288 1288 1153 933 768 641 545 457 378
Larghezza efficace appoggio: 50 mm
Working width support: 50 mm
2,50 2,75 3,00 3,25 3,50 3,75 4,00 4,25 4,50 4,75 5,001,751,50 2,00 2,25l = m
P =
Kg.
/m2
Spessorenominale
mm
0,70
1,00
1,20
1,50
0,80
Nominalthickness
528 413 338
529664 434 354 299
627752947 517 437 372
1249 679824989 569 484 419 364 319
1288 1288 1288 1156 978 833 723 633 558 493 418 393 356 323
Larghezza efficace appoggio: 50 mm
Working width support: 50 mm
2,50 2,75 3,00 3,25 3,50 3,75 4,00 4,25 4,50 4,75 5,001,751,50 2,00 2,25l = m
P =
Kg.
/m2
Spessorenominale
mm
0,70
1,00
1,20
1,50
0,80
Nominalthickness
516 453 401 353
558 443 363 298
559704 459 379 319
1002 667797 552 462 397 342 297
1284 1049 724874 609 619 449 389
1288 1288 1288 1288 1038 593888 768 668
* peso calcolato rispetto alla larghezza utile - weight calculated relevant to working width
Valori in BLU: stati limite ultimoCarichi variabili uniformemente distribuitiVariable uniformly distributed loads BLU values: ultimate limit states
Valori in ROSSO: Limite di freccia 20 mm o L = 1 /180 della luceRED values: serviceability limit states 20 mm or L = 1/180 span
32 ST 4.L - REV. 1 - 11/2014
q
q = carico di esercizio variabile / service variable loadl
TABELLE PORTATE - LOAD TABLE
I valori delle tabelle sono stati determinati considerando coefficienti di combinazioni delle azioni variabili come previsto dalle NTC 08 per edifici di categoria D(ambiente ad uso commerciale). Il contenuto delle tabelle è da considerarsi con semplice valore indicativo. E’ competenza del progettista calcolare per ognisingolo caso i relativi valori. / The table values have been calculated considering combination coefficient of variable actions as expected by NTC 08 for Dcategory building (commercial use building). The table content is to be considered as indicative: it’s competence of designer to calculate, for every single case,the relative values.
Resistenza al taglio longitudinale: metodo di “interazione parziale” / Longitudinal shear resistance: method of partial interaction
Acciaio zincato / Galvanized steelS280 GD - UNI EN 10346
ITPH 75 BETON570 (Passo Greche / Ribs step190 mm)
Carico permanente / permanent load p = 0,00 KN/m2
(il carico permanente comprende il peso di pavimentazione, sottofondo e impianti fissi) (the permanent load includes floor weight, subgrade and fixed equipmentes)
• rottura cilindrica / cylinder break fck = 25 N/mm2
• soletta con calcestruzzo normale / composite floor with normal concrete
Per lo S.L.S. elemento appoggiato limitazione 1/300 della freccia - For S.L.S. supported element deflection 1/300 span
0,7 2,75 2,00 2,25
3,00 2,50 2,50
3,25 3,00 3,25
3,50 3,50 3,75
3,75 4,75 4,50
171,6
172,8
175,2
177,6
181,6
0,8
1,0
1,2
1,5
HSpessoresoletta
/Thicknesscomposite
floor
SSpessorelamiera
/Steel
thickness
Luce massima infase di getto /
Max span during concrete casting
m
Pesosoletta
/Weight
compositefloor
2 app 3 app 4 appmm
120mm
�0,089N/mm2
��τu, Rd = determinato con Rapporto di Prova N° 312267: prova di carico su solaio in calcestruzzo secondo il D.M. 14/01/2008 e la norma UNI EN 1994-1-1:2005 e relazionetecnica N° 312267 - Valutazione della resistenza al taglio longitudinale di progetto di solette composte con lamiere grecate / Calculated with test report N° 312267:load test on concrete floor according to D.M. 14/01/2008 and norm UNI EN 1994-1-1:2005 and technical report N° 312267 - valuation of design longitudinal shear ofconcrete composite floor with trapezoidal steel sheet.
Kg./m2
Larghezza efficace appoggio: 50 mm
Working width support: 50 mm
l=m
q =
Kg.
/m2
q =
Kg.
/m2
1,50 1,75 2,00 2,25 2,50 2,75 3,00 3,25 3,50 3,75 4,00 4,25 4,50 4,75 5,00 5,25 5,50 5,75 6,00
955 795 675 580 505 445 395 350 315 280 255 230 205 185 170
975 815 690 595 520 460 405 365 325 295 265 240 220 200 180
990 825 705 605 530 470 415 370 335 300 270 245 225 205 185
1005 840 715 620 540 475 425 380 340 305 280 255 230 195 165
1010 845 720 620 545 480 430 385 345 310 280 240 205 175 145
0,7
0,8
1,0
1,2
1,5
2 app 3 app 4 appmm
130mm
��0,089N/mm2
Kg./m2 l=m 1,50 1,75 2,00 2,25 2,50 2,75 3,00 3,25 3,50 3,75 4,00 4,25 4,50 4,75 5,00 5,25 5,50 5,75 6,00
0,7
0,8
1,0
1,2
1,5
2 app 3 app 4 appmm
140mm
�0,089N/mm2
Kg./m2 l=m 1,50 1,75 2,00 2,25 2,50 2,75 3,00 3,25 3,50 3,75 4,00 4,25 4,50 4,75 5,00 5,25 5,50 5,75 6,00
0,7
0,8
1,0
1,2
1,5
2 app 3 app 4 appmm
150mm
��0,089N/mm2
Kg./m2 l=m 1,50 1,75 2,00 2,25 2,50 2,75 3,00 3,25 3,50 3,75 4,00 4,25 4,50 4,75 5,00 5,25 5,50 5,75 6,00
2,75 2,00 2,25
3,00 2,50 2,50
3,25 3,00 3,25
3,50 3,50 3,75
3,75 4,75 4,50
171,6
172,8
175,2
177,6
181,6 1085 905 765 680 575 505 450 400 355 320 290 260 235 215 195
1110 925 785 680 595 520 465 415 370 335 300 275 250 225 205
1125 940 800 690 605 530 470 420 380 340 310 280 255 230 210
1145 955 810 700 615 540 480 430 385 350 315 285 250 215 185
1150 960 820 705 620 545 485 435 390 355 310 265 225 195 165
2,75 2,00 2,25
3,00 2,50 2,55
3,25 3,00 3,25
3,50 3,50 3,75
3,75 4,75 4,50
171,6
172,8
175,2
177,6
181,6
q =
Kg.
/m2
1220 1015 860 740 645 570 505 450 400 360 325 295 265 240 220
1245 1040 885 760 665 585 520 465 415 375 340 305 280 250 230 210 190
200 180
1265 1055 895 775 675 595 530 475 425 385 345 315 285 260 235
1280 1070 910 785 685 605 540 480 435 390 355 320 275 235 200 170
210 180
1290 1075 915 790 695 610 545 485 435 395 340 290 245 210 180 155
2,75 2,00 2,25
3,00 2,50 2,55
3,25 3,00 3,25
3,50 3,50 3,75
3,75 4,75 4,50
171,6
172,8
175,2
177,6
181,6
q =
Kg.
/m2
1350 1125 955 820 715 630 560 500 445 400 360 325 300 270 250
1380 1150 980 845 735 650 575 515 460 415 375 340 310 280 255 230 210
220 200
1400 1165 990 855 750 660 585 525 470 425 385 345 315 285 260
1420 1185 1005 870 760 670 595 535 480 435 390 345 295 255 220 185 160
225 195
1425 1190 1015 875 765 675 600 540 485 430 365 315 270 230 195 165
τu, Rd
τu, Rd
τu, Rd
τu, Rd
ST 4.L - REV. 1 - 11/2014 33
Caratteristiche dei materiali Materials characteristics
Condizioni generali di vendita AIPPEG 2013 delle lamiere grecate, dei pannelli metallici coibentati e degli accessori:
Allegato A: Norme sulla movimentazione, manipolazione e stoccaggioAllegato B: Standard qualitativiAllegato C: Raccomandazioni per il montaggioAllegato D: Istruzioni per l’ispezione e la manutenzione
A richiesta possono essere fornite protezioni superficiali con particolari caratteristiche di resistenza e/o idonee al contatto con gli alimenti in accordo al D.M. del 21/03/73 ed alle direttive 82/711/CEE, 85/572/CEE, 90/128/CEE, 92/39/CEE.
Acciaio naturale tipo Aluzinc:Lega Protettiva: Al 55 % - Zn 43,4 % - Si 1,6 %
Acciaio naturale tipo Magnelis:Lega Protettiva: Zn 93,5 % - Al 3,5 % - Mg 3,0 %
Alluminio in lega:Conforme alle norme EN 485-2 e EN 1396 naturale o preverniciato secondo i sistemi precedentemente descritti.
Comportamento al fuoco:Classe di Reazione al Fuoco Standard: A1 in accordo alla norma UNI EN 13501-1
Supporti:Acciaio zincato: sistema SENDZIMIR, conforme alle norme UNI EN 10346 e UNI EN 10143.A richiesta possono essere forniti supporti in acciaio con differenti grammature di zinco.
Il prodotto zincato, non preverniciato, è soggetto all'insorgere a fenomeni precoci di ossidazione.
Acciaio preverniciato:• Sistema Base - Poliestere Standard• Sistema Super - Poliestere Siliconato• Sistema PVDF - Polivinildenfluoruro• Sistema HDX - Poliuretanica + Poliammide• Sistema Plastisol 200 µ - PVC• Sistema Farm - Ambienti Interni Aggressivi• Plastificato Alimentare - Solo Uso Interno
2013 AIPPEG general selling conditions for corrugated sheets, insulated panels and accessories:
Enclosures A: Rules concerning moving, handling, and stockingEnclosures B: Quality standardsEnclosures C: Advices concerning the assembling Enclosures D: Instructions for inspections and maintenance
On request surface protections can be supplied with particular characteristics of resistance and/or suitable for contact with food products in accordance with the Law of 21/03/73 and EU directives 82/711/EEC, 85/572/EEC, 90/128/EEC and 92/39EEC.
Natural steel type Aluzinc:Protective alloy: Al 55 % - Zn 43,4 % - Si 1,6 %
Natural steel type Magnelis:Protective alloy: Zn 93,5 % - Al 3,5 % - Mg 3,0 %
Aluminum alloy :According to EN 485-2 and EN 1396 Standards, smooth or embossed, natural or prepainted according to the previously described system.
Fire reaction :Standard fire reaction class: A1 according to the norm UNI EN 13501-1
Supports:Galvanized steel: SENDZIMIR system, in accordance with UNI EN 10346 and UNI EN 10143. Upon demand we can supply you supports having different zinc coatings.
The galvanized product, not prepainted, is subject to early phenomena of oxidation.
Prepainted steel:• Base System - Standard Polyester• Super System - Polyester base Silicon• PVDF System - Polyvinyldenedifluoride • HDX System - Polyurethane paint + Polyamide • Plastisol 200 µ - PVC• Farm System - Internal aggressive environment• Pvc Coated for alimentary use - Only Internal Use
Allgemeine Verkaufsbedingungen AIPPEG 2013 für Trapezbleche, Isolierpaneele und Zubehör:
Anhang A: Regeln für Handhabung, Bewegung und LagerungAnhang B: QualitätsstandardsAnhang C: MontageempfehlungenAnhand D: Anleitungen für Inspektion und Instandhaltung
Auf Wunsch können Schutzanstriche mit besonderen Eigenschaften in Bezug auf Festigkeit und/oder lebensmittelgeeignet gemäß Min. VO vom 21.03.73 und den weiteren EU-Richtlinien 82/711/CEE, 85/572/CEE, 90/128/CEE, 92/39/CEE geliefert werden.
Natural Stahl wie Aluzinc:Schutzlegierung: Al 55 % - Zn 43,4 % - Si 1,6 %
Natural Stahl wie Magnelis:Schutzlegierung: Zn 93,5 % - Al 3,5 % - Mg: 3,0 %
Aluminiumlegierung:Gemäß EN 485-2 und EN 1396, glatt oder gaufriert, Natur oder vorlackiert nach den vorstehend beschriebenen Systemen.
Verhalten dem Feuer gegenüber:Standard Brandklasse-Reaktionsklasse: A1 in Übereinstimmung mit der Norm UNI EN 13501-1.
Trägermaterial:Verzinktes Blech: System SENDZIMIR, gemäß Normen UNI EN 10346 und UNI EN 10143.Auf Anfrage können Sandwichpaneele mit Stahlträger mit unterschiedlichen Zink Verkleidungen geliefert werden.
Das nicht vorlackierte verzinkte Produkt, untersteht dem Aufträten von vorzeitigen Oxydation Phänomene.
Vorlackiertes Stahl:• Basis-System - Standard Polyester• Super System - Silikon Polyester• PVDF System - Polivinildenfluoruro • HDX System - Polyurethan + Polyamid• Plastisol 200 µ - PVC• Farm System - Aggressive Innenräume• Nahrungsmittel kunstoffbeschichtet - Nur für Innenraum-Anwendungen
Conditions Générales de Vente AIPPEG 2013 des tôles nervurées, des panneaux sandwich isolantes et des accessoires:
Annexe A: Normes pour la mouvementassions, la manipulation et le stockageAnnexe B : Standards qualitativesAnnexe C: Prescriptions techniques pour l’assemblageAnnexe D: Prescriptions pour l’inspections et la maintenance
Sur demande nous pouvons fournir des protections superficiels avec des caractéristiques particulières de résistance et/ou adaptées au contact avec les aliments conformément au D.M. du 21/03/73 et aux directives 82/711/CEE, 85/572/CEE, 90/128/CEE, 92/39/CEE.
Acier Naturel type Aluzinc:Alliage Protective: Al 55 % - Zn 43,4 % - Si 1,6 %
Acier Naturel type Magnelis:Alliage Protective: Zn 93,5 % - Al 3,5 % - Mg 3,0 %
Alliage d’aluminium:Conforme aux normes EN 485-2 et EN 1396, lisse ou gaufré, naturel ou prélaqué avec les systèmes décrits plus haut.
Comportement au feu:Classe de Réaction au Feu Standard: A1 selon la norme UNI EN 13501-1.
Supports:Acier galvanisé: système SENDZIMIR, conforme aux normes UNI EN 10346 et UNI EN 10143. Sur demande on peut produire panneaux sandwich en acier avec différent poids de zinc.
Le produit galvanisé, pas prelaqué, est sujet à tôt phénomène d'oxydation.
Acier Prelaqué:
• Système Base: Standard Polyester • Système Super: Polyester Siliconât• Système PVDF: Polivinildenfluorure• Système HDX: Polyuréthane et Polyamide • Plastisol 200 µm - PVC• Système Farm - Pour les environnements intérieures agressives• Plastifié pour l'industrie alimentaire - seulement à usage interne
38 ST 4.L - REV. 1 - 11/2014