KLP-410 series �U�s�e�r� �M�a�n�u�a�l[Multiplex House Lobby Phone User/Installation Manual]

■ Household call & conversation feature

■ Guard call & conversation feature

■ Routed guard call feature

■ Automatic door open feature using common PIN code

■ Automatic door open feature using household PIN code

■ Automatic door open feature using RF-Card (※KLP-C410R)

KLP-410 Series

�L�O�B�B�Y�P�H�O�N�E

KLP-410 series N0326

SINCE

1976KOREA COMMUNICATIONS CO.,LTD

http://www.kocom.comE-mail : export@kocom.co.krThis manual is based on the date as shown in the right and specifications are subject tochange without notice for quality improvement

Warranty

Warranty Card

1. Name of the product.2. Model number of the product.3. The area of problem.4. Phone number and address at which you can be contacted.

1) This product is produced under strict quality control and inspection procedures. 2) If this product breaks down during proper use as a result of product defect, KOCOM will repair it within one year from date of purchase free of charge. 3) The following cases will be subject to charge, even during warranty period: a. Breakdown during transport, or through careless treatment, by consumer. b. Breakdown cause by unauthorized repair, or system modification. c. Breakdown caused by natural disaster or power disorder.

PRODUCT

MODEL

DATE PURCHASED

WARRANTY PERIOD

AGENCY ADDRESS

KOCOM Warranties the original purchaser of this product as follows.

To receive after service, have the following ready before you contact our branches.

www.kocom.com

�C�a�u�t�i�o�n�s� �f�o�r� �s�a�f�e�t�y

�C�a�u�t�i�o�n

�W�a�r�n�i�n�g

For safe use, please stick to the following cautions.

·Please, save this manual after reading these instructions carefully. ·Read and understand all instructions to set up rightly.

·This Cautions for Safety may include items that are not contained in specifications of the product that consumer purchases.

·If you need assistance with the set-up or operation, please contact with A/S center.

To help our customers to understand this manual, to prevent any personal injury or property damage, some marks are used in the manual.

The marks and the drawing signs are below. Please, understand the marks before reading the manual.

Cautions for set-up

The important marks in the manual.

The meaning of the drawing signs.

Sign to show what not to do Mishandling the device with ignoring this sign may result in serious injury or death.

Mishandling the device with ignoring this sign may result physical injury or material damage.

Sign to tell you that you should follow the instructions. Sing to tell you that you need more attention including high voltages, electric shock, danger, warning)

Sign to tell you that you can't disassemble this unit. Sign to tell you that you must unplug the unit.

·The law limits distributing the power lines to an authorized person from government. The work from an unaurhtorized person cause fire or electric shock.

·Place this unit securely on a stable surface. Serious damafe and/or injury may result if the unit falls.

·Do not set up this unit near the leaking place because it may expose you to dangerous voltages or other risks.

·Even if your product is water proof, do not install it slanted place of water leakage, which can a short circuit.

·The work of distributing wires needs skills and experiences. So please, for assistance, contact your dealer or call service center.

·The communication lines should be built in being distant from the power source. This may result in the risk of fire, electric shock and communication disorder.

·Setting the communication lines in a high humid place such as outside without any protection from rain causes the communication disorder.

·Keep the hook at the wall-mounted device safe. The hook may cause the physical injury.

·Think about the thickness and quality of wall material. The unqualified material may make the device fall.

Warnings for Usage·Do not install this unit near the water and dust, for example, in a bathroom or near the washing machine. It caused fire and electric shock.

·Do not install this unit near the fire, for example, near kitchen sink, heater or the like.

·Do not install near the noxious gar such as Hydrogen Sulfide, metal power and the like.

·Do not install near the water and chemicals.

·Do not give any damage, break and modify the plug. Overloading, heating, pulling causes the damage.

·Do not place the plug near the heater. The damaged code causes fire and electric shock. Do not pull the power code when unplugging.

·The damaged code causes fire and eclectic shock. Must pull with plug. Do not touch with wet hands. It causes the electric shock.

·Do not use any other voltage, except the marked regular voltage.

·Do not use the power terminal at the units to other electric device except the designed device.

·Do not install the units at the leaking place if it doesn’t have any waterproof mark. Do not install the unit when the power is on.

·Install the circuit breaker after checking the safety such as electric shock and leakage. Turn off the power before you install or A/S

·Check the suitability of the lines for installing when you use the exiting lines.

·Do the wiring work by using the designed material.

·Connect the electric wire with the designed ways and ground.

·Do not connect with any other devices except the designed devices to compose the system.

·Unplug electric wire and communication lines from the units before moving to another place.

·Unplug this device when you want to check the inside. If there is no plug, please, turn off the circuit breaker.

·Unplug this device when you try to move it to another place. If the electric line is connected inside of the unit, please contact your dealer or service center.

·Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning

Cautions for Repairs and Maintenance·Keep the inside of the device clean. Having the dust inside without any cleaning for a long time causes the fire. If necessary, contact your dealer or service center to get cleaning service.

·Set the device of the wall-mounted type not to fall. Falling from an earthquake causes personal injury.

�C�a�u�t�i�o�n

·Change the damaged electric code.

·Unplug this unit from plug socket and refer servicing to an authorized service center when the following conditions occur:

·If liquid has been spilled into the unit. 쪾·If the unit does not work normally by following the operating instructions.

·If the unit exhibits a distinct change in performance. 쪾·If the unit has been dropped or physically damaged.

·Do not disassemble this unit at will as this device is composed by precision parts. 쪾·Install the unit by following the set-up instructions of Kocom.

·Do not touch or insert any foreign substances, for example, sticker, magnetic, opener and the like

·Make U-type at the end of wires as the rain can effect on the system by following the wires during the rainy season.

Cautions for Use

Cautions for Abnormality

Safety Instructions, Warnings and Cautions of Each System

·This unit is not designed for security purpose. 쪾·Do not handle the unit with the wet hands.

·Do not place a pot with water or a small metal material on the Units.

·Do not cover the ventilating opening or put any metal material in the units. 쪾

·During thunderstorms, avoid using this unit. 쪾There may be a remote risk of an electric shock from lighting.

·Do not modify the unit. ·Open the main gate after checking ID if the image and sound system do not work. Call A/S

·Do not disassemble the back and cabinet cover.

·Separate the AC/DC lines with the hook of the wall-mounted type when installing. 쪾·Connect the lines after peeling the wires properly

·Do not distribute signal line with AC line. 쪾·Use the designed driver to connect the lines to terminal

·Do not clean the LCD with the damp cloth for cleaning. Use the only dry and soft cloth. 쪾·Do not install the main gate monitor at the leaking place.

Videophone

·This product is designed as a home videophone and cannot use continuously like monitor camera.

·If there is temperature difference between inner part of camera and surrounding, dew condensation occurs on camera lens and may disturb image.

If dew condensation is removed from camera lens, image quality recovers.

·White LED light examination range is narrower than camera shot range at night, so there is less amount of light at night than day.

So it is difficult to see the face in low illumination condition due to noise increase on screen, but it is not from defect.

·Monitor screen (liquid crystal panel) is not in defect when some pixels always light or black out.

·Please install monitor and camera over 5cm away. Also, avoid installing at a place with too much noise, because too much noise around camera causes phone call inferiority.

·Do not place an object within 20cm in front of monitor. It causes phone call inferiority, especially because microphone is installed at the top of monitor.

·If strong light such as sunlight flows into camera module, screen saturation (or strange mark) and image shaking might occur.

·This is not a defect, so please do not install camera where a direct ray of light do not flow if possible.

Things You Need to Know

·In some cases there is occurrence of product destruction, malfunction, noise mixing and picture quality deterioration due to mixing of other tool’s induced voltage or thunder with communication wiring of monitor/camera, monitor/extended monitor. Do not wire with power line such as outdoor wiring or AC power, or phones and other tools. ·You cannot use it if you incorrectly wire the AC voltage between monitor/camera, monitor/extended monitor. Call the store or agency where you purchased this product and consult to solve the problem. Beware that unfixable damage might be caused due to authorizing AC voltage on communication wiring of monitor/camera, monitor/extended monitor. ·Do not ever disjoint this product. It may cause electrocution accident when touching high-voltage circuit inside this product. ·Outside power authorizing this product must be confirmed of product description and use rated voltage. Beware that if higher voltage is authorized, unfixable damage might be caused due to product destruction. ·Power must be connected to domestic voltage (product rated voltage) consent or interior wiring. If connected to other motive power or inverter-type power, product destruction, noise mixing, and picture distortion may occur. ·Do not drop this product. Glass is used for monitor and might break, or cause other circuit inferiority. In such case, immediately turn down the power switch, and call to consult agency or store in which this product was purchased. ·If installed near transmission antenna such as broadcasting station, electric wave may mix and cause picture distortion or voice mixing. ·Avoid installing near tools with strong electromagnetic waves such as microwaves and cell phones, or it may cause picture distortion. ·Do not install monitor in following places. ① Above or around water heater, rice-cooker, heater ② Place exposed to direct rays of the sun ③ Place with temperature below 0'C such as cold store ④ Place with high humidity such as bathroom, washroom, heated room ⑤ Place with a lot of gas, dust, smoke ⑥ Dangerous place with sprays of water or chemicals·Do not wipe with insecticide, drugs or chemicals such as thinner and alcohol, or it may damage the surface of this product. ·Beware of occurrence of image quality deterioration or malfunction from cause of humidity due to penetration of chemicals or water into camera’s urea resins. ·As in the picture, it prevents temperature difference of camera (outside) and monitor (inside), and removes dew condensation caused by humidity of camera window. ·Camera must be installed when wall cement is completely dry. ·When product is installed in winter below -5'C, wait for approximately 2 hours to connect. Dew formation in monitor and camera due to temperature difference inside and outside may cause product defect. ·Avoid installing monitor and camera in place directly exposed to heat or where gas noxiousness is highly occurring.

Cautions

Stop up P.V.C pipe usingadiabatic substances, toprevent air circulation

Tubing Box Monitor

Pipe

Camera(Outdoor, Door)

32

Based on 15V

/2A (A

daptor specification)

Distance betw

een lobby phones is within

10M w

hen connecting 2 lobby phones

Based on 15V

/2A (A

daptor specification)

Distance betw

een lobby phones is within

10M w

hen connecting 2 lobby phones

Door cam

era

Door cam

era

Door cam

era

Door cam

era

15V/ 2A

Adapter specification (Based on 1 set)

Additional A

dapter Installation

1. Able to connect 2 lobby phones(w

hen distance of each lobby phone from

adaptor is with in 10M

)2. N

eed to add Adaptor w

hen install lobby phone 1 set +

more than 20 sets of interphone.

Additional adaptor is required to install for

every additional 20 interphones.

CNT14

①①

①①CNT12

CNT14

①①

①①CNT12

Multiple A

partment System

Line(C

omm

on wire)

Terminal Box

Multiple A

partment System

Line(C

omm

on wire)

Terminal Box

Guard

master

5 wires for interphone w

iring (Pow

ered by lobby phone)

1) DC+15V

~18V

3) GND

4) VO

ICE 1

5) VO

ICE 2

7) DATA

8) Autom

atic Door +

12V9) A

utomatic D

oor GND

8) Autom

atic Door +

12V9) A

utomatic D

oor GND

8) Autom

atic Door +

12V9) A

utomatic D

oor GND

8) Autom

atic Door +

12V9) A

utomatic D

oor GND

GND/V

oice 1/Voice 2/D

ATA

(4 wires)

polarized IV 0.8m

m and above can be used

Power (+

18V/G

ND) (2 w

ire) polarized IV 1.2m

m and

above can be usedVideo signal/G

ND use coax cable: U

se 5C-2V

GND/V

oice 1/Voice 2/D

ATA

(4 wires) polarized IV

0.8mm

and above can be used

Power (+

15V/G

ND) (2 w

ire) polarized IV 1.2m

m

and above can be used

Guard

master

4 5

Wiring Diagram Wiring Diagram

OUTPU

T

INPU

T

INPU

TIN

PUT

OUTPU

T

Coax cable

UTP

Coax cableOUT

PUT

OUT

PUT

INPU

TMaxim

um 3 sets of lobby phone can be added.

44

44

DVR

15V/ 2A

Door cam

era

Door cam

era

Door cam

era

Door cam

era

①①①

①①①

6 7

Name of each part

Installation

Product Spec

Mic : Voice input

Guard Call Button : Used to call guard

Cancel Button : Used to cancel calling

KLP-C410Power Source

Power for internal operationLobby Phone Data Type

Call Type Hands-free Type (2-Way)PROTOCOL DATA TX/RX Type

Call & Video Waiting Time 30 second waiting time after call, 3 minutes for call to household.Housing Material Aluminum (A/L), PC, ABS

Dimension (W)174 X (H)263 X (D)15 (mm)Guaranteed Operation

Temperature-10℃~50℃

LED On Feature 10-Key LED turned on for callingVideo Angle Feature to adjust up, down, left, right (90°) None

Link with RF Card Not linked 13.56MHz

DC 12V

DC 15V~18V(Standby:4W, Operation:10W)

Product Name KLP-C410RDC 15V~18V(Standby:4W, Operation:10W)

Not linked

KLP-D410DC 15V~18V(Standby:3W, Operation:7W)

Components of product

1,500

1,220

1,780

Back case

Main Body

Box

Lobby Phone Sun visor(Option)Box(Option)

Mood Lamp : Turns on to find it in night time

RF Card Reader : Door opens by contacting of RF Card

(Available only with RF Card Model)

FND Display : Displays household

number and during setup

10 Key Dial Button : Displays household

number and during setup

Camera Lens : Send video image during call

Call Button : Used to call household

90°

Wiring Diagram

●For link with sensor : - Setup J P 1 : No relation SW2 :

- Wiring Pin 7 of CNT7 : Fire sensor (+) Pin 9 of CNT7 : Fire sensor (-)

Pin 8 of CNT7 : PIR sensor (+)Pin 9 of CNT7 : PIR sensor (-) Sensor_GND

●External power connection with Dead bolt Pin 5 of CNT7 - Dead bolt_GND Pin 6 of CNT7 – Connect to Dead bolt +

■Lobby Phone Terminals

■Lobby Phone Terminal Connection

●For link with dead bolt : Dead bolt consumes a lot of current, so it is essential to connect external power. - Setup J P 1 : Connect pin 1-2 SW2 :

- Wiring Pin 8 of CNT12 – Dead bolt +12V Pin 9 of CNT12 – Dead bolt_GND

11

3

1

321

9

JP1

CNT12 CNT7

CNT14

CNT4

SW2

1

10

8

●For link with Automatic Door : - Setup J P 1 : Connect pin 2-3 SW2 :

- Wiring Pin 6 of CNT7-Connect Automatic door contact + and Pin 8 of CNT12-Automatic door contact-(No polarity)

●For link with Striker : - Setup J P 1 : Connect pin 1-2 SW2 :

- Wiring Pin 8 of CNT12 – Striker +12V Pin 9 of CNT12 – Connect Striker_GND

●Open/Close Contact N/O COM N/C

A B

CD

1

1

3

1

31

9

JP1

SW2

1

10

8

CNT14 (Video Output)

8) GND7) DVR VIDEO Output6) GND5) GND4) Additional Lobby Video Input 23) Additional Lobby Video Input 12) VIDEO2 Output1) VIDEO1 Output

A CNT12 (for household connection)

9) Switch_GND8) Switch Output (+)7) DATA6) VIDEO 1 Output5) Voice24) Voice13) GND2) NC1) DC+15V

C CNT7 (Sensor & Switch)

10) Fire & PIR sensor Power (+)9) Fire & PIR sensor contact & GND8) PIR sensor contact (+)7) Fire sensor contact (+) 6) DOOR_SW_+/DEAD_BOLT_POWER+5) DEAD_BOLT/ STRIKER_GND4) Not Used3) N/C Contact2) COM Contact1) N/O Contact

D

CNT4 Connection

3) GND2) NC1) +15V

BJP1(DOOR TYPE)

2) N/O for 2, 3 connection1) N/C for 1, 2 connection

Body Sensor

On the basis ofthe center oflobbyphone’slens

(Unit : mm)

Standard installation height of lobbyphone is 1,400~1,450mm

from floor to the bottom of flush mounting box.

In case that the installation height of lobbyphone is out of the

range (min.1,250mm~1,550mm), it’s hard to get proper

image, so be careful about the installation height of lobbyphone.

■Standard height for installation of Lobbyphone

Sub videophone 8P*300mm

Power 2P*300mm

Household 9P*300mm

DC 15V~18V / 2.0A AdapterSensor & Switch 10P*300mm

4×30mm Screw (4ea)

4×10mm Screw (2ea) 4×8mm Bolt (2ea)

3×12mm Screw (1ea)

“L”wench

• Please change the master Pin code after installation.

① - System PIN Number Setup Menu

② - Common PIN Number Setup Menu

③ - Lobby Door Open On-Time Setup Menu

④ - Guardroom Routed Call/Interphone Setup Menu

⑤ - RF-Card Registration Menu

⑥ - RF-Card Deletion by Household Menu

⑦ - All RF-Card Deletion Menu

⑧ - Lobby Phone ID Setup Menu

⑨ - Use of DVR Link Setup Menu

⑩ - System Link Version Setup Menu

⑪ - English/Korean Comment Setup Menu

▷Entering Menu Setup

▷Function to open lobby door using household PIN number

▷LED Operation Mode Functions

• Pressing [*] and [#] at the same time in waiting status will blink [MEnu] for 2 seconds at FND, and display [- - - -] for PIN number input.

• It enters to PIN number setup menu after pressing system PIN number followed by [#]. (Default pin code : 9999)

▷System PIN Number Setup

• FND displays [- - - -]after blinking currently registered system PIN number twice when pressing [Cancel]button from System PIN Number Setup menu.

• Now, pressing new 4 digit PIN number and pressing [#] button. It will blink entered PIN number twice and setup is completed,

and it will display next setup menu of “Common PIN Number Setup”.

▷Common PIN Number Setup

• Pressing [Cancel]button from Common PIN Number Setup menu will blink currently registered common PIN number twice and FND displays [- - - -].

• Now, input new 4 digit PIN number and press [#] button. It will blink new PIN number twice and setup is completed, and it will display next setup

menu of “Lobby Door Open On-Time Setup”.

hhhh 0100[Enter Menu]

[Menu] blinks for2 seconds

Enter PINnumber

Completionbutton

[Program Version]blinks for 2 seconds

[System PINNumber Set]

▷Menu display and switching between menu

• Menu is switched to next menu every time pressing [Guard] button.

• Frequently used menus of 1~10 can be directly accessed by pressing 1,2,3,4,5,6,7,8,9,0 numeric key.(Pressing 0 will move to Menu 10.)

• Menu 11, “English/Korean Menu” can be accessed by pressing [Guard] button.

9EPS

LBPS 8282Enter new

PIN number

1234Current PIN

number blinking [System PIN

Number Setup] Change

completion[Enter Menu]

9EPS 8282Enter new

PIN number

1234Current PIN

number blinkSetup menu

displayChange

completion[Enter Menu]

- - - -Waiting

for input

- - - -Waiting for

input

hhhh[Enter Menu]

[Menu] blinksfor 2 seconds 4,5,6,8,0 Input

Completionbutton

[LED OperationMode 0]

[System WaitingStatus]

[Menu] blinksfor 2 seconds

Completionbutton

[LED OperationMode 1]

[System WaitingStatus]

hhhh[Enter Menu] 1,2,3,8,0 Input

hhhhHousehold PINnumber input

0101Household

number inputDoor openedCompletion

button

[- - - -] appears at FND when pressing [#] button after pressing household number. Pressing 4 digit PIN of corresponding household and [#] will

open lobby door that is connected with lobby phone. [OPEn] is displayed at FND with tone sound.

• Lobby door is opened only for set time.

• One PIN number is allowed for each household.

• Pressing [*] and [#] at the same time in waiting status will blink [Menu] for 2 seconds at FND, and display [- - - -] for PIN number input.

LED Operation Mode 0 Setup : FND displays [Led.0.] when pressing 4,5,6,8,0 and [#] in sequence from [- - - -] state, and it sets LED Operation Mode 0.

LED Operation Mode 1 Setup : FND displays [Led.1.] when pressing 1,2,3,8,0 and [#] in sequence from [- - - -] state, and it sets LED Operation Mode 1.

It is returned to waiting state with LED turned off after 2 seconds (LED is on when touching touch panel).

Touch panel (Key) front LED is always on.

LED in normally off, and is turned on when

user touches touch-panel (Key).

Caution

8 9

Setup Setup

▷ Guardroom Routed Call Setup

• Pressing [Cancel] button from Guardroom Routed Call menu will blink currently setup value [no] to FND, and the light is on.

• Now, set whether user would Guardroom Routed Call function. Selecting 1 means to use the function, and selecting 0 means not to use the function.

• Select whether to use the function or not, and press [#] button. It will blink the selected status that indicates setup completion, and display the next

setup menu of “RF-Card Registration”.

▷RF-Card Registration

• Pressing [Cancel] button from RF-Card Registration menu will blink household input waiting status [Sd.id.] to FND, and [____] appears to input the

household number.

• Input the household number to register the RF-Card, and press [#] button. It will display [Card].

• Contact the RF-Card to the reader when [Card.] appears, then the RF-Card is registered.

“[[]]”appears when registration is successful, and [Card.]appears again in a few second to register other RF-Card so user can register multiple cards.

• It will automatically return to RF-Card Registration menu after specified period (15 seconds).

• RF-Card can be registered up to maximum 1000 cards without regard to the number of households.

▷ RF-Card Deletion by Household Menu

• Pressing [Cancel] button from RF-Card Deletion by Househole menu will blink household input waiting status [Sd.id.] to FND, and [____] appears

to input the household number.

• Input the household number to delete the RF-Card, and press [#] button. It will display [C.dEL.]. After a few seconds, RF-Card Data is deleted for

corresponding household and blink“[[]]”to indicate deletion is completed, and [____] appears again to input household number for other RF-Card

to delete

• Input the household number and press [#] button. It will delete corresponding household’s RF-Card Data.

Current status blink

Enter new number (0, 1)to set whet to use the function

Setup MenuDisplay

Changecompletion

ChangeButton

YES

HouseholdNumber ID

Setup MenuDisplay

Inputcompletion

ChangeButton

Input HouseholdNumber

1004Registrationcompletion

[ [ ] ]Wait for

RF-Card inputWait for

RF-Card input

____Wait for input

HouseholdNumber ID

Setup MenuDisplay

Inputcompletion

Change Button Input HouseholdNumber

1004Deletion

completion

[ [ ] ]____Wait for input

____Wait for RF-Card

input

▷ All RF-Card Deletion Menu

• Pressing [Cancel] button from All RF-Card Deletion menu will display [dEL.?] in FND that asks whether the user really wants to delete all RF-Card.

• Pressing [#] button will count up from [d.001]~[d.470], and display “[[]]” when it is completed, and display All RF-Card Deletion menu [A.dEL.].

HouseholdNumber ID

Setup MenuDisplay

Inputcompletion

ChangeButton

Last numberof deletion

start of deletion

[ [ ] ]Deletion

completionDisplay Setup

Menu

▷Lobby Door Open On-Time Setup

• Pressing [Cancel] button from Lobby Door Open On-Time Setup menu will blink currently setup value [t-02] to FND, and the light is on.

• Now, press 1~8 to change the value and press [#] button. It will blink registered Door Open On-Time time and setup is completed, and it will

display next setup menu of “Guardroom Routed Call Setup Menu” (The unit of time is second).

Current Door OpenOn-Time blink

Enter new DoorOpen On Time

Setup MenuDisplay

Changecompletion

ChangeButton

▷Register household PIN number

[----] appears at FND when pressing [#][#][0][0][#] in sequence during call with household device.

Now, enter PIN number and press [#] button, and household PIN number is registered with [P.YES.] display.

0 0 p.yes.PIN registered

HHHHEnter PIN Change

Completion

During call with household - - - -

Input Hold

10 11

Setup Setup

PIN Number Input Completion blinking

Move to next setup menu

PIN Number Input Completion blinking

Move to next setup menu

Move to next setup menu

Move to next setup menu

Move to next setup menu

Move to next setup menu

Register otherRF-Card

Registrationcompletion

RegisterRF-Card

Input HouseholdNumber

Input HouseholdNumber

Return to “RF-Card Registration Menu” by pressing * button or after certain time.

②Common PIN Number Setup

Enter new PIN number

Current PIN number blinking

Enter new PIN number

Current PIN number blinking

①System PIN Number Setup

③Lobby Door Open On-Time Setup Current setuptime blinking

Current setuptime blinking

Entered setup time Blink

Entered state

⑤RF-Card Registration

④Guardroom Routed Call Interphone Setup

Blink

DeletionCompletion

Wait for HouseholdNumber

⑥RF-Card Deletion by Household

⑦All RF-Card Deletion Are you sure todelete all?

Deletion startnumber

Deletion endnumber

DeletionCompletion

[Program Version Display]

+ Wrong PINNumber(3 Times)

Correct PIN Number

SystemPIN Number

→ #

Blink Enter PIN Number

[Lobby Phone in Waiting Status]

[Press at the same time]

Enter System PIN Number

1~8 Input

‘7’Enter number

#1

‘1’Enter number

1 is set to use the function, 0 is set to not use the function

1 digit number input #1

1. Pressing menu number buttons ①②③④⑤⑥⑦⑧⑨⑩ move directly to corresponding

menu. However, menu ⑪ is selected by pressing [Guard] button.

2. Pressing [*] button from each setup menu display state will cancel the menu setup,

and it is returned to Lobby Phone Waiting [ -] state.

3. Pressing [*] button from each setup input state will return back to menu setup state.

4. The system password is 9999 when the factory ships the products.

hhhh____

Return to “RF-Card Registration Menu” by pressing * button or after certain time.

Return to “All RF-Card Deletion Menu” after deletion completion

⑧Lobby Phone ID Setup Current LobbyPhone ID

Waiting forID Input

Input new LobbyPhone ID

ID Input Completion(Blink)

⑨Use of DVR Link Setup Current setup status Input status Input Completion(Blink)

Input Completion(Blink)

Input Completion(Blink)

#2

‘1’Enter number

1 is set to use the function, 0 is set to not use the function

1 digit number input #2

1 is set to use Version 1 (New), 0 is set to Version 0 (Old)

1 digit number input #3

⑩System Link Version Setup Current setup status Input status#3

‘1’Enter number

⑪English/Korean Comment Setup

Move to first “① System PIN Number Setup”

Current setup status Input status#2

‘1’Enter number

▷ Use of DVR Link Setup Menu

■ General scenario by setup menu and each button

• Pressing [Cancel] button from Use of DVR Link Setup menu will blink currently setup status [no] to FND, and the light is on.

• Now, input whether to use DVR Link. Selecting 1 means to use the function, and selecting 0 means not to use the function.

• Select whether to use the function or not, and press [#] button. It will blink the selected status that indicates setup completion, and display the next

setup menu of “System Link Version Setup Menu”.

Currentstatus blink

Enter new number (0, 1) to set whet to use the function

Setup MenuDisplay

Changecompletion

ChangeButton

YES

Current statusblink

Select System (0, 1) Setup MenuDisplay

Change completionChangeButton

▷ System Link Version Setup Menu

• Pressing [Cancel] button from System Link Version Setup Menu will blink currently setup status [Pr-0] to FND, and the light is on.

• Now, select the version to link with the system and enter it.

• Selecting 0 means to use the Communication Protocol-0 (Old Version) for this system.

• Selecting 1 means to use the Communication Protocol-1 (New Version) for this system.

• Select System Link Version and press [#] button. It will blink the selected status that indicates setup completion, and display the next setup menu

of “English/Korean Comment Setup Menu”.

▷ English/Korean Comment Setup Menu

• Pressing [Cancel] button from English/Korean Comment Setup Menu will blink currently setup value [no] to FND, and the light is on after 2 second.

• Select and enter English/Korean Comment. Selecting 1 means to use English Comment, and selecting 0 means not to use English Comment.

• Not selecting English Comment means to use Korean Comment.

• Select which comment to use and press [#] button. It will blink the selected status that indicates setup completion, and display the next setup menu

of “System PIN Number Setup”.

▷ Changing the English/Korean Comment selection using fixed PIN number

• Pressing [*] and [#] at the same time in waiting status will blink [Menu] for 2 seconds at FND, and display [- - - -] for PIN number input.

• (1) Korean Comment – Enter fixed PIN number (137950) for English/Korean Comment Change and press [#]. It will display [ENGL]->[ no] and

change to Korean Comment is completed. System will be in waiting mode.

Setup MenuDisplay

ChangeButton

Current statusblink

Select Comment (0, 1)

Changecompletion

YES

01.00

Setup MenuDisplay

Changecompletion

ChangeButton

Enter LobbyPhone Numbe

Waiting for inputCurrent LobbyPhone ID blink

▷ Lobby Phone ID Setup

• Pressing [Cancel] button from Lobby Phone ID Setup menu will blink current Lobby Phone ID number [Lb.01.], and displays [Lb.--] that can input

Lobby Phone ID number.

• Now, input Lobby Phone ID number and press [#] button. It will complete Lobby Phone ID change, and it will display next setup menu of

“Use of DVR Link Setup Menu”.

hhhh[Enter Menu] [Menu] blinks fo

2 secondsEnter fixed PIN

number Completion

button Display Comment

Menu(for 1 second) Set to Korean Comment(displayed for 1 second)

SystemWaiting Mode

• (2) English Comment - Enter fixed PIN number (137958) for English/Korean Comment Change and press [#]. It will display [ENGL]->[ YES] and

change to English Comment is completed. (All sound is expressed in Tone voice when English Comment is selected.)

LBPS

9EPS

8282 82821234 ____

8282 82821234 ____

YES YES

1004 [ [ ] ]

1004 [ [ ] ] ____

[ [ ] ]

YES YES

YES YEShhhh[Enter Menu] [Menu] blinks fo

2 secondsEnter fixed PIN

number Completion

button Display Comment

Menu(for 1 second) Set to English Comment(displayed for 1 second)

SystemWaiting Mode

HouseholdNumber

HouseholdNumber

YES

130326_KLP-410_영문메뉴얼 1130326_KLP-410_영문메뉴얼 2130326_KLP-410_영문메뉴얼 3130326_KLP-410_영문메뉴얼 4130326_KLP-410_영문메뉴얼 5130326_KLP-410_영문메뉴얼 6