Chart Garages Specifications & Prices · Chart Garages Specifications & Prices Manufacturer of ......

Chart Garages Specifications & Prices

Manufacturer of quality Garages, Carriage Houses and Workshops.

2 01233 229898 [email protected] www.chartgarages.co.ukPlease Note: Timber sizes quoted are sawn dimensions and are slightly smaller after planing.

We reserve the right to alter our specifications without notice.

ContentsGaragesSpecifications 4

Prices 6

Carriage HousesSpecifications 8

Prices 9

WorkshopsSpecifications 10

Prices 11

More photographs are available on our website www.chartgarages.co.uk 3For any Garage or Carriage House with an eaves height of 2.7m and over, (not including the height of the roof) full scaffolding will be required.

Contacts & Delivery

Avon £280

Bedfordshire £195

Berkshire £210

Buckinghamshire £185

Cambridgeshire £185

Channel Islands POA

Cheshire POA

Clywd POA

Cornwall £540/£840

Cumbria POA

Derbyshire £340

Devon POA

Dorset £275

Dyfed POA

Essex £75/£150

Glamorgan – Mid/South POA

Glamorgan – West POA

Gloucestershire £320

Gwent POA

Gwynedd POA

Hampshire £165

Herefordshire £300

Hertfordshire £160

Humberside POA

Kent FREE

Lancashire POA

Leicestershire £260

Lincolnshire POA

London £120

Middlesex £140

Norfolk POA

Northamptonshire £245

Northumberland POA

Nottinghamshire £300

Oxfordshire £190

Powys POA

Shropshire £360

Somerset £330

Staffordshire £325

Suffolk £225

Surrey FREE

Sussex – East FREE

Sussex – West £150

Warwickshire £250

Wiltshire £270

Worcestershire £300

Yorkshire – South £390

Yorkshire – North POA

Delivery Charges

UK & European Sales OfficeChart House, Dencora Way,

Ashford, Kent TN23 4FH

Chart Garages+44 (0)1233 229898

[email protected]

Chart Stables+44 (0)1233 611123

[email protected]

Fencing Sales Office+44 (0)1233 626188

[email protected]



Garage SpecificationsThe Clipper RangeWall ConstructionWalls are built with 75mm x 50mm (3” x 2”) timber framing, spaced at 600mm (2’) centres, diagonally braced at corner sections, where necessary.

Wall CladdingSelected high-quality Shiplap 16mm x 150mm (5⁄8” x 6”), pressure treated to ensure a long maintenance- free life. All boarding is fixed with rust-resisting nails. Weatherboard is available as an option.

Wall LiningAn eco-breather membrane to meet the requirements of BS 4016 Type 2, is placed between the studwork and exterior cladding of all wall panels and doors. Various internal wall linings and insulation are available on request.

Roof ConstructionPurlins are 100mm x 50mm (4” x 2”) held in place by joist holders on prefabricated trusses, covered with 11mm OS Board and black Onduline roof sheeting or 38kg green mineral felt. Further options include coloured Onduline, Onduvilla tiles or felt tiles.

Double DoorsDouble doors are framed, ledged and braced, faced with Shiplap. Doors are hung on 450mm adjustable hook and band hinges. Double doors are 2.1m wide x 2.082m high (7’ x 6’ 10”), as standard.

Personal DoorsAre not included as standard but can be fitted as an optional extra.

WindowsAre not included as standard. An extensive range of single or double glazed windows are available.

HeightTo eaves 2235mm (7’ 4”) when on a single course of brickwork. Apex height will vary depending upon the width of the building; please enquire.

GutteringIs not fitted as standard but can be included as an optional extra.

Barge BoardsAll in pressure treated, prepared timber, fixed with rust-resisting nails. No overhangs to gable ends.

Timber TreatmentAll timber is pressure treated (excluding roof purlins), adding to the longevity of your building.

The Chart RangeWall ConstructionWalls are built with 100mm x 50mm (4” x 2”) timber framing, spaced at 600mm (2’) centres and are diagonally braced at corner sections, where necessary.

Wall CladdingSelected high-quality Shiplap 16mm x 150mm (5⁄8” x 6”) pressure treated to ensure a long maintenance- free life. All boarding is fixed with rust-resisting nails. Weatherboard and Loglap are available as options.


Roof ConstructionPurlins are 125mm x 50mm (5” x 2”) held in place by joist holders on prefabricated trusses, then covered with 11mm OS Board and black Onduline roof sheeting or 38kg green mineral felt. Options include coloured Onduline or felt tiles.

Double DoorsDouble doors are framed, ledged and braced, faced with Shiplap cladding. Doors are hung in a pressure treated door frame, on adjustable hook and band hinges. Double doors are 2.2m wide x 2.082m high (7’ 6” x 6’ 10”) and side hinged, as standard. Larger and taller double doors are available to suit the eaves height, as well as a range of canopied up & over doors and sliding doors.

Personal DoorAs standard your garage will include a single 838mm x 2082mm (2’ 9” x 6’ 10”) personal door, framed, morticed, ledged and braced and faced with shiplap and fitted with a five levered morticed door lock. This door is hung in a pressure treated door frame with cill. Inward or outward opening doors are available.


HeightTo eaves we offer 2235mm (7’ 4”) or 2464mm (8’ 1”) when on a single course of brickwork. Apex height will vary depending upon the width of the building; please enquire.

GutteringBlack 100mm (4”) half-round guttering and downpipes are fitted to both sides of the building.

Barge BoardsAll in pressure treated, prepared timber, fixed with rust-resisting nails. Your Garage will include a 100mm overhang, to each gable end. These will be underlined.


For any Garage or Carriage House with an eaves height of 2.7m and over, (not including the height of the roof) full scaffolding will be required. More photographs are available on our website www.chartgarages.co.uk 5

The Chester RangeWall ConstructionWalls are built with 100mm x 50mm (4” x 2”) timber framing, spaced at 600mm (2’) centres and are diagonally braced at corner sections, where necessary.

Wall CladdingSelected high-quality Shiplap 19mm x 125mm (3⁄4” x 5”), pressure treated to ensure a long maintenance- free life. All boarding is fixed with stainless steel nails. Weatherboard and Loglap are available as options.


Roof ConstructionRoofs are of a trussed rafter design and manufactured to BS5268 Part 2 2002, Part 3 2006, BS6399 Part 1 1996 and Part 2 1997. As standard the roof pitch is 22.5°, boarded with 18mm (3⁄4”) OS Boards and covered with Onduvilla tiles. Hip roofs are available. The pitch of the trusses can be increased up to 35° to accommodate slate or clay tiles.

Soffits and FasciaAre fitted as standard and the soffits and fascias are 150mm x 25mm (6” x 1”) and pressure treated.

Double DoorsDouble doors are framed, morticed, ledged and braced, rebated and infilled with 19mm x 125mm (3⁄4” x 5”) T.G.V. Doors are hung in a pressure treated, heavy-duty frame with 600mm (24”) adjustable hook and band hinges. Doors secured with rimlock and pull handle, lockable from inside and out. Doors are 2286mm wide x 2235mm high (7’ 6” x 7’ 4”) and side hinged, as standard. Larger double doors are available as well as a range of canopied up & over doors and sliding doors.

Personal DoorAs standard your garage will include a single 915mm x 1981mm (3' x 6’ 6”) personal door framed, morticed, ledged and braced, rebated and infilled with 19mm x 125mm (3⁄4” x 5”) T.G.V. and fitted with a five levered morticed door lock. This door is hung in a pressure treated door frame with cill. Inward or outward opening doors are available. A range of alternative sized doors are also available.


HeightMeasures (8’ 1”) to eaves when on a single course of brickwork. Apex height will vary depending upon the width of the building; please enquire.

GutteringBlack 100mm (4”) half-round guttering and downpipes are fitted as standard.

Timber TreatmentAll timber is pressure treated (excluding trusses), adding to the longevity of your building.

Should You Wish To Have Slate, Clay Or Cedar Tiles

To accommodate Clay, Slate or Cedar tiles we increase the pitch of the roof up to

a maximum of 35°. Please telephone one of our specialist advisors to discuss the

preferred option to suit your requirements and locality.

GA

RA

GE

S



All prices exclude VAT. Prices include installation - Refer to page 3 for delivery charges

Clipper Chart Chester Chester

3m (10’) Wide 5.4m x 3.0m (18’ x 10’) £2,145 £2,850 £4,345 £3,445

7.2m x 3.0m (24’ x 10’) £2,525 £3,295 £5,275 £4,225

9.1m x 3.0m (30’ x 10’) £3,185 £4,075 £6,275 £4,945

10.9m x 3.0m (36’ x 10’) £3,565 £4,495 £7,195 £5,715

12.8m x 3.0m (42’ x 10’) £4,115 £5,275 £8,145 £6,495

14.6m x 3.0m (48’ x 10’) £4,545 £5,595 £9,125 £7,250

3.6m (12’) Wide 5.4m x 3.6m (18’ x 12’) £2,245 £2,995 £4,675 £3,745

7.2m x 3.6m (24’ x 12’) £2,645 £3,395 £5,825 £4,675

9.1m x 3.6m (30’ x 12’) £3,295 £4,115 £6,925 £5,495

10.9m x 3.6m (36’ x 12’) £3,675 £4,665 £8,025 £6,425

12.8m x 3.6m (42’ x 12’) £4,225 £5,225 £9,125 £7,295

14.6m x 3.6m (48’ x 12’) £4,645 £5,650 £10,225 £8,185

4.2m (14’) Wide 5.4m x 4.3m (18’ x 14’) £2,575 £3,395 £4,995 £3,995

7.2m x 4.3m (24’ x 14’) £2,965 £3,845 £6,155 £4,925

9.1m x 4.3m (30’ x 14’) £3,675 £4,445 £7,295 £5,875

10.9m x 4.3m (36’ x 14’) £4,115 £5,125 £8,495 £6,815

12.8m x 4.3m (42’ x 14’) £4,725 £5,825 £9,675 £7,695

14.6m x 4.3m (48’ x 14’) £5,215 £6,315 £10,825 £8,695

4.8m (16’) Wide 5.4m x 4.8m (18’ x 16’) £2,725 £3,675 £5,650 £4,560

7.2m x 4.8m (24’ x 16’) £3,185 £4,225 £6,975 £5,495

9.1m x 4.8m (30’ x 16’) £3,845 £4,685 £8,295 £6,595

10.9m x 4.8m (36’ x 16’) £4,345 £5,395 £9,675 £7,695

12.8m x 4.8m (42’ x 16’) £4,945 £6,045 £10,595 £8,515

14.6m x 4.8m (48’ x 16’) £5,445 £6,595 £11,925 £9,545

35° Pitch for tiled roof

Garage Prices

For any Garage or Carriage House with an eaves height of 2.7m and over, (not including the height of the roof) full scaffolding will be required. More photographs are available on our website www.chartgarages.co.uk 7All prices exclude VAT. Prices include installation - Refer to page 3 for delivery charges


Clipper Chart Chester Chester

5.4m (18’) Wide 5.4m x 5.4m (18’ x 18’) £3,515 £4,535 £6,595 £5,275

7.2m x 5.4m (24’ x 18’) £3,895 £4,945 £7,965 £6,375

9.1m x 5.4m (30’ x 18’) £4,945 £6,095 £9,450 £7,565

10.9m x 5.4m (36’ x 18’) £5,495 £6,595 £10,935 £8,745

12.8m x 5.4m (42’ x 18’) £6,595 £7,695 £12,425 £9,895

14.6m x 5.4m (48’ x 18’) £7,195 £8,295 £13,855 £10,995

6.1m (20’) Wide 7.2m x 6.1m (24’ x 20’) £5,845 £8,545 £6,745

9.1m x 6.1m (30’ x 20’) £7,195 £10,345 £8,275

10.9m x 6.1m (36’ x 20’) £7,875 £11,975 £9,550

12.8m x 6.1m (42’ x 20’) £9,125 £13,675 £10,975

14.6m x 6.1m (48’ x 20’) £9,795 £15,350 £12,345

7.3m (24’) Wide 7.2m x 7.3m (24’ x 24’) £6,295 £9,545 £7,645

9.1m x 7.3m (30’ x 24’) £7,825 £11,445 £9,175

10.9m x 7.3m (36’ x 24’) £8,945 £13,350 £10,695

12.8m x 7.3m (42’ x 24’) £10,450 £15,275 £12,250

14.6m x 7.3m (48’ x 24’) £11,135 £17,250 £13,775

GA

RA

GE

S

For Hipped Ends on Chester Range Garages and Carriage Houses with roof pitches up to 35° please add...

For Barn Hips on Chester Range Garages and Carriage Houses with roof pitches up to 35° please add...

3.0m £895 per end

3.6m £950 per end

4.2m £1,025 per end

4.8m £1,295 per end

5.4m £1,495 per end

6.1m £1,595 per end

7.3m £1,995 per end

3.0m £155 each

3.6m £170 each

4.2m £185 each

4.8m £200 each

5.4m £215 each

6.1m £225 each

7.3m £1245 each



The Chart RangeWall ConstructionWalls are built with 100mm x 50mm (4” x 2”) timber framing, spaced at 600mm (2’) centres, diagonally braced at corner sections, where necessary.

Wall CladdingSelected high-quality Shiplap 16mm x 150mm (5⁄8” x 6”), pressure treated to ensure a long maintenance- free life. Weatherboard and Loglap are available as options. All boarding is fixed with rust resisting nails.

Wall LiningA traditional eco-breather membrane to meet the requirements of BS 4016 Type 2 is placed between the studwork and exterior cladding in all wall panels. Various internal wall linings and insulation are available on request.

Roof ConstructionPurlins are 125mm x 50mm (5” x 2”) held in place by joist holders on prefabricated trusses, covered with 11mm OS Board and black Onduline roof sheeting or 38kg green mineral felt. Options include coloured Onduvilla or felt tiles.

EntrancesEntrance ways to Carriage Houses have 150mm x 150mm (6” x 6”) pressure treated support posts, framing and 457mm (18”) curved bracing. Doors can be fitted as optional extras.

DoorsAre not included as standard. A wide range of double doors and personal doors are available on request.

WindowsAre not included as standard. An extensive range of single or double glazed windows is available.

HeightTo eaves, 2464mm (8’ 1”) when on a single course of brickwork. Carriage Houses are also available with an eaves height of 2743mm (9’) as an option. Apex heights will vary depending upon the width of the building, please enquire.

GutteringBlack 100mm (4”) half-round guttering and downpipes are fitted to the front and rear.

Barge BoardsAll in pressure treated, prepared timber, fixed with rust-resisting nails. Your Carriage House will include a 100mm overhang, underlined, to each gable end.


The Chester RangeWall ConstructionWalls are built with 100mm x 50mm (4” x 2”) timber framing, spaced at 600mm (2’) centres.

Wall CladdingSelected high-quality Shiplap 19mm x 125mm (3⁄4”x 5”), pressure treated to ensure a long maintenance- free life. Weatherboard and Loglap are available as options. All boarding is fixed with stainless steel nails.

Wall LiningA traditional eco-breather membrane to meet the requirements of BS 4016 Type 2 is placed between the studwork and exterior cladding in all wall panels. Various internal wall linings and insulation are available on request.

Roof ConstructionRoofs are of a trussed rafter design and manufactured to BS5268 Part 2 2002, Part 3 2006, BS6399 Part 1 1996 and Part 2 1997. As standard, the roof pitch is 22.5°, then boarded with 18mm OS Board and covered with Onduvilla tiles. Gable end roofs or hipped roofs are available. Options include Onduline or felt tiles or the pitch of the trusses can be increased up to 35° to accommodate slate or clay tiles.

Soffits and FasciasAre fitted as standard and soffits and fascias are 150mm x 25mm (6" x 1") and pressure treated.

EntrancesEntrance ways to Carriage Houses are constructed using 150mm x 150mm (6” x 6”) Oak with 610mm (24”) curved bracing. Centre support posts are placed on a 150mm (6") staddle stone.

DoorsAre not included as standard. A wide range of double doors and personal doors are available on request.

WindowsAre not included as standard. An extensive range of single or double glazed windows is available.

HeightMeasures 2505mm (8’ 2”) to eaves when on a single course of brickwork. Carriage Houses are available with an eaves height of 2473mm (9’) as an option. Apex heights will vary depending upon the width of the building, please enquire.

GutteringBlack 100mm (4”) half-round guttering and downpipes are fitted as standard.

Timber TreatmentAll timber is pressure treated (excluding roof trusses), adding to the longevity of your building.

Should You Wish To Have Slate, Clay Or Cedar TilesTo accommodate Clay, Slate or Cedar tiles we increase the pitch of the roof up to a maximum of 35°. Please telephone one of our specialist advisors to discuss the preferred option to suit your requirements and locality.

Carriage House Specifications

More photographs are available on our website www.chartgarages.co.uk 9For any Garage or Carriage House with an eaves height of 2.7m and over, (not including the height of the roof) full scaffolding will be required.

CA

RR

IAG

E H

OU

SES

Carriage House Prices5.4m (18') Wide Chart Chester Chester

3m (10’) Bays 3.0m x 5.4m (10’ x 18’) 1 Bay £2,350 £3,995 £3,245

6.1m x 5.4m (20’ x 18’) 2 Bays £3,845 £6,265 £4,995

9.1m x 5.4m (30’ x 18’) 3 Bays £5,425 £8,465 £6,750

12.2m x 5.4m (40’ x 18’) 4 Bays £7,025 £10,715 £8,575

3.6m (12’) Bays 3.6m x 5.4m (12’ x 18’) 1 Bays £2,475 £4,335 £3,450

7.3m x 5.4m (24’ x 18’) 2 Bays £4,295 £7,295 £5,875

10.9m x 5.4m (36’ x 18’) 3 Bays £5,825 £10,395 £8,295

14.6m x 5.4m (48’ x 18’) 4 Bays £7,415 £13,350 £10,725

6.1m (20’) Wide

3m (10’) Bays 3.0m x 6.1m (10’ x 20’) 1 Bay £2,695 £4,495 £3,595

6.1m x 6.1m (20’ x 20’) 2 Bays £4,295 £7,375 £5,895

9.1m x 6.1m (30’ x 20’) 3 Bays £6,075 £10,295 £8,150

12.2m x 6.1m (40’ x 20’) 4 Bays £7,695 £13,215 £10,565

3.6m (12’) Bays 3.6m x 6.1m (12’ x 20’) 1 Bay £2,875 £4,895 £3,935

7.3m x 6.1m (24’ x 20’) 2 Bays £4,675 £8,195 £6,575

10.9m x 6.1m (36’ x 20’) 3 Bays £6,525 £11,585 £9,275

14.6m x 6.1m (48’ x 20’) 4 Bays £8,275 £14,895 £11,925

7.2m (24’) Wide

3m (10’) Bays 3.0m x 7.3m (10’ x 24’) 1 Bay £2,975 £4,995 £4,045

6.1m x 7.3m (20’ x 24’) 2 Bays £4,715 £8,445 £6,745

9.1m x 7.3m (30’ x 24’) 3 Bays £6,645 £11,895 £9,495

12.2m x 7.3m (40’ x 24’) 4 Bays £8,445 £15,245 £12,215

3.6m (12’) Bays 3.6m x 7.3m (12’ x 24’) 1 Bay £3,145 £5,345 £4,275

7.3m x 7.3m (24’ x 24’) 2 Bays £4,995 £8,995 £7,195

10.9m x 7.3m (36’ x 24’) 3 Bays £7,145 £12,650 £10,115

14.6m x 7.3m (48’ x 24’) 4 Bays £8,995 £13,375 £13,135

Attach a Workshop Chart Chester Chester

3.0m x 5.4m (10’ x 18’) £2,525 £3,625 £2,895

3.0m x 6.1m (10’ x 20’) £2,795 £3,995 £3,185

3.0m x 7.3m (10 x 24’) £3,075 £4,495 £3,625

3.6m x 5.4m (12’ x 18’) £2,645 £4,125 £3,295

3.6m x 6.1m (12’ x 20’) £2,995 £4,345 £3,515

3.6m x 7.3m (12’ x 24’) £3,295 £4,725 £3,795

Attach a Garage 3.0m x 5.4m (10’ x 18’) £2,645 £3,745 £2,995

3.0m x 6.1m (10’ x 20’) £2,895 £4,095 £3,295

3.0m x 7.3m (10 x 24’) £3,185 £4,615 £3,695

3.6m x 5.4m (12’ x 18’) £2,745 £4,245 £3,395

3.6m x 6.1m (12’ x 20’) £3,125 £4,455 £3,565

3.6m x 7.3m (12’ x 24’) £3,395 £4,845 £3,895

The above prices include a 1195mm x 1045mm (47' x 41') opening double glazed casement window and a 838mm wide personal door.

The above prices include a set of 2.4m (8') double doors





Workshop SpecificationsThe Clipper RangeWall ConstructionWalls are built with 75mm x 50mm (3” x 2”) timber framing, spaced at 600mm (2’) centres, diagonally braced at corner sections, where necessary.

Wall CladdingSelected high-quality Shiplap 16mm x 150mm (5⁄8” x 6”), pressure treated to ensure a long maintenance- free life. All boarding is fixed with rust resisting nails. Weatherboard is available as an option.

Wall LiningA traditional wall eco-breather membrane made to meet the requirements of BS 4016 Type 2 is placed between the studwork and exterior cladding in all panels and doors. Various wall linings and insulation are available on request.

Roof ConstructionPurlins are 100mm x 50mm (4” x 2”) held in place by joist holders on prefabricated trusses, boarded with 11mm OS Board and black Onduline roof sheeting. Coloured Onduline, 38kg green mineral felt, Onduvilla tiles or felt tiles are available as an alternative.

DoorsA single 838mm (2’ 9”) wide x 2082mm (6’ 10”) high framed, ledged and braced door faced with shiplap, secured with 450mm (18") T hinges and a pad bolt. Larger single or double doors are available.

WindowsOne 980mm x 662mm (39” x 26”) single glazed window (1 x opening, 1 x fixed pane) or 1 x clear roof sheet is included in buildings up to and including 3.6m (12’) in length. Two windows are fitted as standard in longer Workshops. Alternative single glazed or double glazed windows are available.

HeightTo eaves 2235mm (7’ 4”) when on a single course of brickwork. Apex heights will vary depending upon the width of the building, please enquire.


Barge BoardsAll in pressure treated, prepared timber, fixed with rust-resisting nails. No overhangs to gable ends.

FlooringFloors are constructed using 75mm x 50mm (3” x 2”) framing, spaced at 300mm (12”) centres and covered with 18mm OS Board.


The Chart RangeWall ConstructionWalls are built with 100mm x 50mm (4” x 2”) timber framing, spaced at 600mm (2’) centres, diagonally braced at corner sections, where necessary.

Wall CladdingSelected high-quality Shiplap 16mm x 150mm (5⁄8” x 6”), pressure treated to ensure a long maintenance- free life. All boarding is fixed with rust resisting nails. Weatherboard is available as an option.

Wall LiningA traditional wall eco-breather membrane made to meet the requirements of BS 4016 Type 2 is placed between the studwork and exterior cladding of all wall panels and joinery grade doors. Various wall linings and insulation are available on request.

Roof ConstructionPurlins are 125mm x 50mm (5” x 2”) held in place by joist holders on prefabricated trusses, boarded with 18mm OS Board and covered with Onduvilla tiles, (available in brown, red or black/ grey). Options include Onduline, 38kg Green mineral felt or felt tiles.

DoorsAs standard your Workshop will include a single 838mm x 2082mm (2’ 9” x 6’ 10”) personal door, morticed, ledged and braced frame, faced with shiplap and fitted with a five levered morticed door lock. This door is hung in a pressure treated door frame with sill. Inward or outward opening doors are available.

WindowsOne 980mm x 662mm (39” x 26”) single glazed window (1 x opening, 1 x fixed pane) or 1 x clear roof sheet is included in buildings up to and including 3.6m (12’) in length. Two windows are fitted as standard in longer workshops. Alternative single glazed or double glazed windows are available.

HeightTo eaves 2235mm (7’ 4”) when on a single course of brickwork. Apex heights will vary depending upon the width of the building, please enquire.


Barge BoardsAre pressure treated, prepared timber, fixed with rust-resisting nails. 100mm overhangs to each gable end, underlined.

FloorsFloors are constructed using 75mm x 50mm (3” x 2”) framing, spaced at 300mm (12”) centres and covered with 18mm Ply.


For any Garage or Carriage House with an eaves height of 2.7m and over, (not including the height of the roof) full scaffolding will be required.

Workshop PricesThe Chester RangeWall ConstructionWalls are built with 100mm x 50mm (4” x 2”) timber framing, spaced at 600mm (2’) centres, diagonally braced at the corner sections, where necessary.

Wall CladdingSelected high quality Shiplap Ex 19mm x 125mm (3/4” x 5”), pressure treated to ensure a long maintenance- free life. All boarding is fixed with rust resisting nails. Weatherboard is available as an option.

Wall LiningA traditional wall eco-breather membrane made to meet the requirements of BS 4016 Type 2 is placed between the studwork and exterior cladding of all wall panels and joinery grade doors. Various wall linings and insulation are available on request.

Roof ConstructionRafters set at 600mm centres, felt battened and tiled by us with slate. As standard the pitch of the roof would be 22.5° but this may vary slightly depending on the width of your building. Clay tiles are available as an alternative but the pitch required to take clay tiles will be much steeper.

DoorsThe Chester range of Workshop will include a single 915mm x 1981mm joinery grade personal door VAC VAC treated, framed, ledged and braced, with top two thirds of door incorporating a 20mm double glazed casement window, bottom on third will be rebated and infilled with T.G.V. Door secured with a five levered mortice lock and hung on butt hinges.

WindowsOne 980mm x 1050mm joinery grade 14mm double glazed window, pressure treated; to include one fixed and one opening pane. A range of alternative sized windows are available as an option.

HeightTo eaves 2248mm (7’ 5”) including depth of timber floor. Apex height will vary depending on the width of the building.

FloorsThe floor is constructed using 75mm x 50mm (3” x 2”) pressure treated frame, spaced at 300mm (12”) centres and covered with 18mm Ply.

Timber TreatmentAll timber is pressure treated including the windows and the door is VAC VAC treated, but excluding the rafters. We now manufacture our own pressure treated joinery grade doors and windows in our on-site joinery Workshop. These new specifications are outlined above.

Clipper Chart Chester

2.4m x 2.4m (8’ x 8’) £1,625 £1,875 N/A

3.0m x 2.4m (10’ x 8’) £1,795 £2,145 £4,395

3.6m x 2.4m (12’ x 8’) £1,975 £2,225 £4,615

4.2m x 2.4m (14’ x 8’) £2,525 £2,895 £5,275

4.8m x 2.4m (16’ x 8’) £2,675 £3,095 £6,275

5.4m x 2.4m (18’ x 8’) £2,895 £3,395 £6,825

3.0m x 3.0m (10’ x 10’) £1,895 £2,295 £4,995

3.6m x 3.0m (12’ x 10’) £2,095 £2,575 £5,495

4.2m x 3.0m (14’ x 10’) £2,645 £3,125 £6,375

4.8m x 3.0m (16’ x 10’) £2,825 £3,345 £6,925

5.4m x 3.0m (18’ x 10’) £3,055 £3,625 £7,585

3.0m x 3.6m (10’ x 12’) £2,065 £2,595 £5,495

3.6m x 3.6m (12’ x 12’) £2,175 £2,725 £6,155

4.2m x 3.6m (14’ x 12’) £2,695 £3,295 £6,925

4.8m x 3.6m (16’ x 12’) £2,945 £3,625 £7,595

5.4m x 3.6m (18’ x 12’) £3,165 £3,945 £8,295

WO

Rk

SHO

pS

More photographs are available on our website www.chartgarages.co.uk 11

Chart Garages & Stables, UK & European Sales Office . Chart Fencing Office

Chart House, Dencora Way, Ashford, Kent TN23 4FH

www.chartgarages.co.uk

[email protected]

+44 (0)1233 229898

www.chartstables.co.uk

[email protected]

+44 (0)1233 611123

www.chartfencing.co.uk

[email protected]

+44 (0)1233 626188

All published prices are subject to change without prior notice. E&OE. 08-2017

Chart Garages Specifications & Prices · Chart Garages Specifications & Prices Manufacturer of ......

Documents

Transcript of Chart Garages Specifications & Prices · Chart Garages Specifications & Prices Manufacturer of ......