Chapter 4 Container - VCI Online · recycling roads / organizations: ... 8 Chapter 4 Container...
Transcript of Chapter 4 Container - VCI Online · recycling roads / organizations: ... 8 Chapter 4 Container...
Status: June 2013 Packaging Handbook
1
Chapter 4 Container
Section 4.0 General information 4.0.0 Contents 4.0 General information 4.0.0 Contents 4.0.1 Introduction 4.0.2 Application 4.0.3 Quality requirements 4.0.4 Recovery systems
4.1 Plastic drum – non removable head (tight head) 4.1.1.1 220 L-Plastic drum – non-removable head (tight head) 4.1.2.1 60 L-Plastic drum – non-removable head (tight head) (jerrican) 4.1.2.2 30 L-Plastic drum – non-removable head (tight head) (jerrican) 4.1.2.3 25 L-Plastic drum – non-removable head (tight head) (jerrican)
4.2 Plastic drum – removable head (open head) 4.2.1.1 150 L-Plastic drum – removable head (open head) 4.2.2.1 120 L-Plastic drum – removable head (open head) 4.2.3.1 60 L-Plastic drum – removable head (open head) 4.2.4.1 30 L-Plastic drum – removable head (open head)
4.3 Cylindrical steel drum – non-removable head (tight head) 4.3.1.1 216.5 L-Steel drum – non-removable head (tight head) (standard) 4.3.2.1 60 L-Steel drum – non-removable head (tight head) 4.3.3.1 30 L-Steel drum – non-removable head (tight head) 4.3.4.1 200 L-Composite drum steel-plastic 4.3.4.2 60 L-Composite drum steel-plastic 4.3.4.3 30 L-Composite drum steel-plastic
Status: June 2013 Packaging Handbook
2
Chapter 4 Container
Section 4.0 General information 4.0.0 Contents
4.4 Cylindrical steel drum – removable head (open head) 4.4.1.1 210 L- Steel drum – removable head (open head) (for liquids) 4.4.1.2 210 L-Steel drum – removable head (open head) (for solids) 4.4.1.3 210 L-Steel drum – removable head (open head) (recessed) 4.4.2.1 60 L-Steel drum – removable head (open head) (for liquids) 4.4.2.2 60 L-Steel drum – removable head (open head) (for solids 4.4.3.1 30 L-Steel drum – removable head (open head) (for liquids) 4.4.3.2 30 L-Steel drum – removable head (open head) (for solids 4.5 Conical steel drum – removable head (open head) 4.5.1.1 120 L-Steel drum – removable head (open head) (for liquids) 4.5.1.2 120 L-Steel drum – removable head (open head) (for solids) 4.5.2.1 60 L-Steel drum – removable head (open head) (for liquids) 4.5.2.2 60 L-Steel drum – removable head (open head) (for solids) 4.5.3.1 30 L-Steel drum – removable head (open head) (for liquids) 4.5.3.2 30 L-Steel drum – removable head (open head) (for solids)
4.6 Fiberboard drum – removable head (open head) 4.6.1.1 200 L-Fiberboard drum – removable head (open head) 4.6.2.1 120 L-Fiberboard drum – removable head (open head) 4.6.3.1 60 L-Fiberboard drum – removable head (open head)
Status: June 2013 Packaging Handbook
3
Chapter 4 Container
Section 4.0 General information 4.0.1 Introduction In the packaging sector a multitude of different container has been used in the past. The chemical industry has agreed upon the following drum sizes in order to stem the multitude of types: ≥ 200 Liter 150 Liter 120 Liter 60 Liter 30 Liter 25 Liter (only plastic drum-non-removable head) For PE-drums (jerricans) are several volumes of the same basic dimensions available. This is possible by the use of different heights tool inserts in a manufacturing tool. 30 L jerricans are for products with reduced density and 25 L jerricans are for products with higher density. For material and manufacturing of packaging the EU- and national directives and regulations are applied (e.g. concentration of heavy metal and recyclability). It is recommended to largely use the container types listed in the following for the following reasons:
Standardization
By use of standard containers low-cost and environment-relevant packaging solutions can be achieved.
Possibility of multiple used Especially for standardized container the possibility to recondition and thus to reuse is
existing. Standardized drums can be used by all fillers in the chemical branch as well.
Frontier crossing traffic It is necessary to put the achieved and present standards into the deciding boards at
DIN/CEN in order to be able to simplify the international exchange of goods and to in-crease possibilities for reconditioning. Corresponding efforts have been given rise to.
Environmental issues Also legal interests have to be taken into consideration with the use of packaging (pack-
aging ordinance, dangerous goods transport). This has been considered when working out the following standard container.
Status: June 2013 Packaging Handbook
4
Chapter 4 Container
Section 4.0 General information
4.0.2 Application Depending on product viscosity drums – non-removable head (tight head) or drums – removable head (open head) are used. In any case the filler bears the responsibility for use of a packing for the individual goods and ways of conveyance. When using packaging for dangerous goods the presuppositions stated in the introduction of section 1.3 have to be observed.
Status: June 2013 Packaging Handbook
5
Chapter 4 Container
Section 4.0 General information
4.0.3 Quality requirements Information on quality assurance can be taken from chapter 9.
Status: June 2013 Packaging Handbook
6
Chapter 4 Container
Section 4.0 General information 4.0.4 Recovery systems
Depending on type and size of respective container there are different recycling roads / organizations:
VDF - Verband der Deutschen Fassverwertungsbetriebe e.V.
KBS - Kreislaufsystem Blechverpackungen Stahl GmbH
RIGK - Gesellschaft zur Rückführung industrieller und gewerblicher Kunststoffverpackungen mbH
Vfw - Vereinigung für Wertstoffrecycling GmbH
RRD - Rücknahmesystem Rekonditionierverpackung Deutschland GmbH
VIV - Verwertungsgemeinschaft Industrieverpackungen GbR
VMS - Verpackungsrücknahme mit System e.V.
More information can be taken from chapter 10 (recovering systems).
Status: June 2013 Packaging Handbook
7
Chapter 4 Container
Section 4.1 Plastic drum – non-removable head (tight head)
4.1.1.1 220 L- Plastic drum– non removable head (tight head) (based on DIN EN 12707)
Measurements and tolerances in mm Total outer height: 935 (±5) Outer diameter: 581 (±5) Minimum wall thickness: 2.2 (VPA 15) Mass in g: 8 000 min. Nominal capacity: 220 L Brimful capacity (min.): 222 L Color: blue (RAL 5010) Material: PE, UV-stabilized Closures: S 70 x 6 mm + S 56 x 4 mm (according to DIN EN ISO 20848-3), if necessary with ventilation Seals: to be chosen according to product requirements Technical requirements: minimum upset resistance (according to VPA 3) axial: 25 000 N characteristic value: 600 N/mm Minimum requirements: approved for packaging group II minimum inner pressure 200 kPa Approval marking: 1H1 ... according to provisions of VPA 6 and respective legal
regulations in force concerning transportation of dangerous goods
Minimum approval: approved for all standard liquids, specific weight min. 1.2 kg/dm³ Material marking: according to VerpackV §14 Residual emptying: according to VPA 4 Standard recommendation without obligation. Issued by Verband der Chemischen Industrie e.V.
Status: June 2013 Packaging Handbook
8
Chapter 4 Container
Section 4.1 Plastic drum – non-removable head (tight head)
4.1.2.1 60 L - Plastic drum – non-removable head (tight head) (jerricans) (based on DIN EN 12712) Measurements in mm Total outer height: ca. 630 Outer length: ca. 380 Outer width: ca. 340 Wall thickness distribution: VPA 15 Nominal capacity: 60 L Brimful capacity (min.): 62 L Colour: blue (RAL 5010) Material: PE, UV-stabilized Handles: alternatively 2 drop handles sideways (VPA 14) and/or 1 car-
rying handle on top Closures: S 60 x 6 mm (according to DIN 12713), if necessary with ventilation Seals: PE-foam or other material to be chosen according to product requirements
Technical requirements: minimum upset resistance (according to VPA 3) axial: 9 000 N characteristic value: 300 N/mm Minimum requirements: approved for packaging group II minimum inner pressure 200 kPa
Approval marking: 3H1 ... according to provisions of VPA 6 and respective legal
regulations in force concerning transportation of dangerous goods
Minimum approval: approved for all standard liquids, specific weight min. 1.2 kg/dm³ Material marking: according VerpackV §14 Residual emptying: according to VPA 4 Standard recommendation without obligation. Issued by Verband der Chemischen Industrie e.V.
Status: June 2013 Packaging Handbook
9
Chapter 4 Container
Section 4.1 Plastic drum – non-removable head (tight head)
4.1.2.2 30 L -Plastic drum – non-removable head (tight head) (jerricans) (based on DIN EN 12712) Measurements in mm Total outer height: ca. 400 to ca. 490 Outer length: ca. 330 Outer width: ca. 290 Wall thickness distribution: VPA 15 Nominal capacity: 30 L Brimful capacity (min.): 32 L Color: blue (RAL 5010) Material: PE, UV-stabilized Handles: handle on top, recessed grip, in bottom Closures: S 60 x 6 mm (according to DIN EN 12713) Seals : PE-foam or other material to be chosen according to product requirements
Technical requirements: minimum upset resistance (according to VPA 3) axial: 5 000 N characteristic value: 250 N/mm Minimum requirements: approved for packaging group II minimum inner pressure 200 kPa Approval marking: 3H1 .... according to provisions of VPA 6 and respective legal
regulations in force concerning transportation of dangerous goods
Minimum approval: approved for all standard liquids; specific weight min. 1.2 kg/dm³ Material marking: according to VerpackV §14 Residual emptying: according to VPA 4 Standard recommendation without obligation. Issued by Verband der Chemischen Industrie e.V.
Status: June 2013 Packaging Handbook
10
Chapter 4 Container
Section 4.1 Plastic drum – non-removable head (tight head)
4.1.2.3 25 L -Plastic drum – non-removable head (tight head) (jerricans) (based on DIN EN 12712) Measurements in mm Total outer height: ca. 460 Outer length: ca. 295 Outer width: ca. 245 Wall thickness distribution: VPA 15 Nominal capacity: 25 L Brimful capacity (min.): 27 L Color: blue (RAL 5010) Material: PE, UV-stabilized Handles: handle on top, recessed grip in bottom Closures: S 60 x 6 mm (according to DIN EN 12713), if necessary with ventilation Seals: PE-foam or other material, to be chosen according to product requirements
Technical requirements: minimum upset resistance (according to VPA 3) axial: 4 000 N characteristic value: 100 N/mm stackable e.g. with stackable dog, handle / interlock in bottom Minimum requirements: approved for packaging group I or II minimum inner pressure 250 kPa (I) and 200 kPa (II) Approval marking: 3H1 .... according to provisions of VPA 6 and respective legal
regulations in force concerning transportation of dangerous goods
Minimum approval: approved for all standard liquids specific weight min. 1.2 kg/dm³ Material marking: according to VerpackV §14 Residual emptying: according to VPA 4 Standard recommendation without obligation. Issued by Verband der Chemischen Industrie e.V.
Status: June 2013 Packaging Handbook
11
Chapter 4 Container
Section 4.2 Plastic drum – removable head (open head)
4.2.1.1 150 L- Plastic drum – removable head (open head)
(based on DIN EN 12714) Measurements and tolerances in mm Total outer height: 960 (±5) Outer diameter: 500 (±4) Fill opening: 380 (±3) Wall thickness distribution: VPA 15 Nominal capacity: 150 L Brimful capacity (min.): 155 L Color body / lid: blue (RAL 5010) / black Material: PE, UV-stabilized
Closures: clamp ring with lever closure Seals: foam rubber (e.g. NBR) or PUR to be chosen according to product requirements (VPA 2) Technical requirements: minimum upset resistance (according to VPA 3) axial: 18 000 N characteristic value: 360 N/mm Minimum requirements: approved for solids packaging group I resp. for liquids of the
packaging group II with inner compression test, minimum inner pressure 100 kPa Approval marking: 1H2 ... according to provisions of VPA 6 and respective legal
regulations in force concerning transportation of dangerous goods
Gross mass: 200 kg min. Material marking: according to VerpackV §14 Residual emptying: according to VPA 4 Standard recommendation without obligation. Issued by. Issued by Verband der Chemischen Industrie e.V.
Status: June 2013 Packaging Handbook
12
Chapter 4 Container
Section 4.2 Plastic drum – removable head (open head)
4.2.2.1 120 L- Plastic drum – removable head (open head) (based on DIN EN 12714) Measurements and tolerances in mm Total outer height: 800 (±5) Outer diameter: 495 (±4) Fill opening: 380 (±3) Wall thickness distribution: VPA 15 Nominal capacity: 120 L Brimful capacity (min.): 124 L Color body / lid: blue (RAL 5010) / black Material: PE, UV-stabilized Closures: clamp ring with lever closure Seals: foam rubber (e.g. NBR) or PUR to be chosen according to
product requirements (VPA 2) Technical requirements: minimum upset resistance (according to VPA 3) axial: 18 000 N characteristic value: 360 N/mm Minimum requirements: approved for packaging group I resp. for liquids of the packaging group II with inner compression test, minimum inner pressure 100 kPa Approval marking: 1H2 ...according to provisions of VPA 6 and respective legal
regulations in force concerning transportation of dangerous goods
Gross mass: 200 kg min. Material marking: according to VerpackV §14 Residual emptying: according to VPA 4
Standard recommendation without obligation. Issued by Verband der Chemischen Industrie e.V.
Status: June 2013 Packaging Handbook
13
Chapter 4 Container
Section 4.2Plastic drum – removable head (open head)
4.2.3.1 60 L - Plastic drum – removable head (open head) (based on DIN EN 12714) Measurements and tolerances in mm Total outer height: 625 (±5) Outer diameter: 395 (±4) Fill opening: 310 (±3) Wall thickness distribution: VPA 15 Nominal capacity: 60 L Brimful capacity (min.): 63 L Color body / lid: blue (RAL 5010) / black Material: PE, UV-stabilized Handles: 2 drop handles sideways (VPA 14), grip pockets in bottom Closures: clamp ring with lever closure Seals: foam rubber (e.g. NBR) or PUR to be chosen according to
product requirements (VPA 2) Technical requirements: minimum upset resistance (according to VPA 3) axial: 9 000 N characteristic value: 300 N/mm Minimum requirements: approved for packaging group I Approval marking: 1H2 .... ... according to provisions of VPA 6 and respective
legal regulations in force concerning transportation of dangerous goods Gross mass: 88 kg min. Material marking: according to VerpackV §14 Residual emptying: according to VPA 4 Standard recommendation without obligation. Issued by Verband der Chemischen Industrie e.V.
Status: June 2013 Packaging Handbook
14
Chapter 4 Container
Section 4.2 Plastic drum – removable head (open head)
4.2.4.1 30 L - Plastic drum – removable head (open head) (based on DIN EN 12714) Measurements and tolerances in mm Total outer height: 520 (±4) Outer diameter: 315 (±3) Fill opening: 250 (±3) Wall thickness distribution: VPA 15 Nominal capacity: 30 L Brimful capacity (min.): 31 L Color body / lid: blue (RAL 5010) / black Material: PE, UV-stabilized Handles: 2 drop handles sideways (VPA 14), grip pockets in bottom Closures: clamp ring with lever closure Seals: foam rubber (e.g. NBR) or PUR to be chosen according to
product requirements (VPA 2) Technical requirements: minimum upset resistance (according to VPA 3) axial: 7 000 N characteristic value: 280 N/mm Minimum requirements: approved for solids packaging group I resp. for liquids of the
packaging group II with inner compression test, minimum inner pressure 100 kPa Approval marking: 1H2 .... ... according to provisions of VPA 6 and respective legal regulations in force concerning transportation of dangerous goods Gross mass: 45 kg min. Material marking: according to VerpackV §14 Residual emptying: according to VPA 4 Standard recommendation without obligation. Issued by Verband der Chemischen Industrie e.V.
Status: June 2013 Packaging Handbook
15
Chapter 4 Container
Section 4.3 Cylindrical steel drum – non-removable head
(tight head)
4.3.1.1 216.5 L - Steel drum-non removable head (tight head) (standard) (based on DIN EN ISO 15750-2) Measurements and tolerances in mm Total outer height: 884 (±3) Outer diameter: 585 (+0/-2) Inner diameter: 571 (+1/-0.5) Minimuml wall thickness: according to licensing requirements Nominal capacity: 216.5 L Brimful capacity (min.): 217 L Color: blue (RAL 5010) Material: steel (EN 10130) Closures: one G 2, one G 3/4 (DIN EN ISO 15750-3), placed opposite each
other on top, 2“-bung hole distance from rim 72 mm Seals: to be chosen according to product requirements Technical requirements: triple fold, adequate for container, 2W-beads (negativ beads) Surface, inside: to be chosen according to product requirements (e.g. raw, coated) Minimum requirements: approved for packaging group I Approval marking: 1A1 .... ... according to provisions of VPA 6 and respective legal regulations in force concerning transportation of dangerous goods Residual emptying: according to VPA 4 Standard recommendation without obligation. Issued by Verband der Chemischen Industrie e.V.
Status: June 2013 Packaging Handbook
16
Chapter 4 Container
Section 4.3 Cylindrical steel drum – non-removable head
(tight head)
4.3.2.1 60 L- Steel drum – non-removable head (tight head)
(based on DIN EN 13007) Measurements and tolerances in mm Total outer height: 680 (+4/-2) Outer diameter: 372 (+4/-2) Inner diameter: 355 (+1/-0.5) Minimum wall thickness: according to licensing requirements Nominal capacity: 60 L Brimful capacity (min.): 61 L Color: blue (RAL 5010)
Material: steel (EN 10130) Handles: 2 drop handles sideways (VPA 14) DIN 6646, lockable Closures: alternatively G 2 once or G 2 + G 3/4 on top (DIN EN ISO 15750-3)
Seals: to bee chosen according to product requirements Technical requirements: triple fold Surface, inside: to be chosen according to product requirements (e.g. raw, coated) Minimum requirements: approved for packaging group I
Approval marking: 1A1 .... ... according to provisions of VPA 6 and respective legal regulations in force concerning transportation of dangerous goods Residual emptying: according to VPA 4
Standard recommendation without obligation. Issued by Verband der Chemischen Industrie e.V.
Status: June 2013 Packaging Handbook
17
Chapter 4 Container
Section 4.3 Cylindrical steel drum – non-removable head
(tight head)
4.3.3.1 30 L - Steel drum – non-removable head (tight head)
(based on DIN EN 13007) Measurements and tolerances in mm Total outer height: 532 (±3) Outer diameter: 290 (±2) Inner diameter: 280 (+1/-0.5) Minimum wall thickness: according to licensing requirements Nominal capacity: 30 L Brimful capacity (min.): 31 L Color: blue (RAL 5010)
Material: steel (EN 10130) Handles: alternatively 2 drop handles sideways (DIN 6646, lockable), 1 carrying handle on top (VPA 14) Closures: alternatively G 2 once or G 2 and G 3/4 on top (DIN EN ISO15750) Seals: to bee chosen according to product requirements
Technical requirements: triple fold Surface, inside: to be chosen according to product requirements (e.g. raw, coated) Minimum requirements: approved for packaging group I
Approval marking: 1A1 ... according to provisions of VPA 6 and respective legal
regulations in force concerning transportation of dangerous goods
Residual emptying: according to VPA 4 Standard recommendation without obligation. Issued by Verband der Chemischen Industrie e.V.
Status: June 2013 Packaging Handbook
18
Chapter 4 Container
Section 4.3 Cylindrical steel drum – non-removable head
(tight head)
4.3.4.1 200 L - Composite drum steel-plastic Measurements and tolerances in mm Total outer height: 884 (±3) Outer diameter: 585 (+0/-2) Inner diameter: 571 (+1/-0.5) Minimum wall thickness: according to licensing requirements Minimum wall thickness inner drum: 1.0 Mass inner drum in g: 3 000 (±120) Nominal capacity: 200 L Brimful capacity (min.): 206 L Material outer drum: steel (EN 10130) Material inner drum: PE Closures inner drum: according to DIN EN ISO 20848-3, S 56 x 4 opposite Closures outer drum: alternatively G 2 once or G 2 and G 3/4 on top (DIN EN ISO15750) Seals outer drum: G ¾ EPDM Seals inner drum: PE or EPDM Technical requirements: triple fold, adequate for container, 2W-beads (negativ beads) Surface, inside: raw, lid coated / galvanized Surface, outside: blu coatet (RAL 5010) according to VPA 7, lid coated / galvanized Minimum requirements: approved for packaging group I Approval marking: 6HA1 .... ... according to provisions of VPA 6 and respective legal regulations in force concerning transportation of dangerous goods Residual emptying: according to VPA 4 Standard recommendation without obligation. Issued by Verband der Chemischen Industrie e.V.
Status: June 2013 Packaging Handbook
19
Chapter 4 Container
Section 4.3 Cylindrical steel drum – non-removable head
(tight head)
4.3.4.2 60 L - Composite drum steel-plastic Measurements and tolerances in mm Total outer height: 682 (+5/-4) Outer diameter: 370 (+6/-4) Inner diameter: 355 (+1/-0.5) Minimum wall thickness outer drum: according to licensing requirements inner drum: 0.8 Mass inner drum in g: 1 100 (±50) Nominal capacity: 60 L Brimful capacity (min.): 60.7 L Material outer drum: steel (EN 10130 Material inner drum: PE Closures inner drum: according to DIN EN ISO 20848-3, S 56 x 4 Closures outer drum: alternatively G 2 once or G 2 and G 3/4 on top (DIN EN ISO15750) Seals: PE or EPDM Handles: triple seam or 2 drop handles sideways (VPA 14) Technical requirements: triple fold, 2 rolling beads Surface, inside: raw Surface, outside: blu coatet (RAL 5010) according to VPA 7 Minimum requirements: approved for packaging group I Approval marking: 6HA1 .... ... according to provisions of VPA 6 and respective legal regulations in force concerning transportation of dangerous goods Residual emptying: according to VPA 4 Standard recommendation without obligation. Issued by Verband der Chemischen Industrie e.V.
Status: June 2013 Packaging Handbook
20
Chapter 4 Container
Section 4.3 Cylindrical steel drum – non-removable head
(tight head)
4.3.4.3 30 L - Composite drum steel-plastic Measurements and tolerances in mm Total outer height: 560 (±3) Outer diameter: 290 (±2) Inner diameter: 280 (+1/-0.5) Minimum wall thickness outer drum: according to licensing requirements inner drum: 0.8 Mass inner drum in g: 700 (±40) Nominal capacity: 30 L Brimful capacity (min.): 30.1 L Material outer drum: steel (EN 10130) Material inner drum: PE Closures: according to DIN EN ISO 20848-3, S 56 x 4 Seals: PE or EPDM Handles: 1 handle on top or 2 drop handles sideways (VPA 14) Technical requirements: triple fold, 2 rolling beads Surface, inside: raw Surface, outside: blu coatet (RAL 5010) according to VPA 7 Minimum requirements: approved for packaging group I Approval marking: 6HA1 .... ... according to provisions of VPA 6 and respective legal regulations in force concerning transportation of dangerous goods Residual emptying: according to VPA 4 Standard recommendation without obligation. Issued by Verband der Chemischen Industrie e.V.
Status: June 2013 Packaging Handbook
21
Chapter 4 Container
Section 4.4 Cylindrical steel drum – removable head
(open head)
4.4.1.1 210 L - Steel drum – removable head (open head) /for liquids (based on DIN EN ISO 15750-1) Measurements and tolerances in mm Total outer height: 880 (±3) Outer diameter: 595 (±3) Diameter over clamp ring: 610 max. Inner diameter: 571 (+1/-0.5) Minimum wall thickness: according to licensing requirements Nominal capacity: 210 L Brimful capacity (min.): 210 L Color: blue (RAL 5010) Material: steel (EN 10130) Closures: clamp ring with lever closure, G 2 once or G 2 and G 3/4 in lid alternatively (DIN EN ISO 15750-3) Seals: to bee chosen according to product requirements (VPA 2) Technical requirements: triple fold Surface, inside: is to be selected accordance with the product-requirements (e.g. raw, coated, PE-Inliner) Minimum requirements: approved for packaging group II minimum inner pressure 100 kPa Approval marking: 1A2 .... ... according to provisions of VPA 6 and respective legal
regulations in force concerning transportation of dangerous goods Residual emptying: according to VPA 4 Standard recommendation without obligation. Issued by Verband der Chemischen Industrie e.V.
Status: June 2013 Packaging Handbook
22
Chapter 4 Container
Section 4.4 Cylindrical steel drum – removable head
(open head)
4.4.1.2 210 L - Steel drum – removable head (open head) (for solids) (based on DIN EN ISO 15750-1) Measurements and tolerances in mm Total outer height: 880 (±3) Outer diameter: 595 (±3) Diameter over clamp ring: 610 max. Inner diameter: 571 (+1/-0.5) Minimum wall thickness: according to licensing requirements Nominal capacity: 210 L Brimful capacity (min.): 210 L Color: blue (RAL 5010)
Material: steel (EN 10130) Closures: clamp ring with lever closure, G 2 once or G 2 and G 3/4 in lid alternatively (DIN EN ISO 15750-3) Seals: to bee chosen according to product requirements (VPA 2) Technical requirements: triple fold Surface, inside: is to be selected accordance with the product requirements (e.g. raw, coated, PE-Inliner) Minimum requirements: approved for packaging group I Approval marking: 1A2 .... ... according to provisions of VPA 6 and respective legal
regulations in force concerning transportation of dangerous goods Residual emptying: according to VPA 4 Standard recommendation without obligation. Issued by Verband der Chemischen Industrie e.V.
Status: June 2013 Packaging Handbook
23
Chapter 4 Container
Section 4.4 Cylindrical steel drum – removable head (open
head)
4.4.1.3 210 L - Steel drum – non-removable head / recessed (adequate for container) Measurements and tolerances in mm Total outer height: 866 (±3) Outer diameter over clamp ring: 585 (±3) Inner diameter: 571 (+1/-0.5) Fill opening: 550 (+1/-0.5) Minimum wall thickness: according to licensing requirements Nominal capacity: 210 L Brimful capacity (min.): 210 L Color: blue (RAL 5010) Material: steel (EN 10130) Closures: clamp ring with lever closure, G 2 once or G 2 and G 3/4 in lid alternatively (DIN EN ISO 15750-3) Seals: to bee chosen according to product requirements (VPA 2) Technical requirements: triple fold Surface, inside: to be chosen according to product requirements (e.g. raw, coated, PE-Inliner) Minimum requirements: approved for packaging group I Approval marking: 1A2 .... ... according to provisions of VPA 6 and respective legal
regulations in force concerning transportation of dangerous goods Residual emptying: according to VPA 4 Standard recommendation without obligation. Issued by Verband der Chemischen Industrie e.V.
Status: June 2013 Packaging Handbook
24
Chapter 4 Container
Section 4.4 Cylindrical steel drum – removable head
(open head)
4.4.2.1 60 L - Steel drum – removable head (open head) / for liquids (based on DIN EN 13008) Measurements and tolerances in mm Total outer height: 680 (+4-2) Outer diameter over clamp ring: 382 (+3/-2) Inner diameter: 355 (+1/-0.5) Minimum wall thickness: according to licensing requirements Nominal capacity: 60 L Brimful capacity (min.): 61 L Color: blue (RAL 5010) Material: steel (EN 10130) Handles: 2 drop handles sideways (DIN 6646, lockable, VPA 14) Closures: clamp ring with lever closure, G 2 once or G 2 and G 3/4 in lid alternatively (DIN EN ISO 15750-3) Seals: to bee chosen according to product requirements (VPA 2) Technical requirements: triple fold, stackable Surface, inside: to be chosen according to product requirements (e.g. raw, coated, PE-Inliner) Minimum requirements: approved for packaging group II minimum inner pressure 100 kPa Approval marking: 1A2 .... ... according to provisions of VPA 6 and respective legal regulations in force concerning transportation of dangerous goods Residual emptying: according to VPA 4 Standard recommendation without obligation. Issued by Verband der Chemischen Industrie e.V.
Status: June 2013 Packaging Handbook
25
Chapter 4 Container
Section 4.4 Cylindrical steel drum – removable head
(open head)
4.4.2.2 60 L - Steel drum – removable head (open head) / for solids (based on DIN EN 13008) Measurements and tolerances in mm Total outer height: 680 (+4/-2)
Outer diameter over clamp ring: 382 (+3/-2)
Inner diameter: 355 (+1/-0.5)
Minimum wall thickness: according to licensing requirements
Nominal capacity: 60 L
Brimful capacity (min.): 61 L
Color: blue (RAL 5010) Material: steel (EN 10130) Handles: 2 drop handles sideways (DIN 6646, lockable, VPA 14) Closures: clamp ring with lever closure, G 2 once or G 2 and G 3/4 in lid alternatively (DIN EN ISO 15750-3) Seals: to bee chosen according to product requirements (VPA 2) Technical requirements: triple fold, stackable Surface, inside: to be chosen according to product requirements (e.g. raw, coated, PE-Inliner) Minimum requirements: approved for packaging group I Approval marking: 1A2 .... ... according to provisions of VPA 6 and respective legal regulations in force concerning transportation of dangerous goods Residual emptying: according to VPA 4 Standard recommendation without obligation. Issued by Verband der Chemischen Industrie e.V.
Status: June 2013 Packaging Handbook
26
Chapter 4 Container
Section 4.4 Cylindrical steel drum – removable head
(open head)
4.4.3.1 30 L - Steel drum – removable head (open head) / for liquids (based on DIN EN 13008) Measurements and tolerances in mm Total outer height: 580 max. Outer diameter over clamp ring: 305 (±2) Inner diameter: 280 (+1/-0.5) Minimum wall thickness: according to licensing requirements Nominal capacity: 30 L Brimful capacity (min.): 30 L Color: blue (RAL 5010) Material: steel (EN 10130) Handles: 2 drop handles sideways (DIN 6646, lockable, VPA 14) Closures: clamp ring with lever closure, G 2 once or G 2 and G 3/4 in lid alternatively (DIN EN ISO 15750-3) Seals: to bee chosen according to product requirements (VPA 2) Technical requirements: triple fold, stackable Surface, inside: to be chosen according to product requirements (e.g. raw, coated, PE-Inliner) Minimum requirements: approved for packaging group II minimum inner pressure 100 kPa Approval marking: 1A2 .... ... according to provisions of VPA 6 and respective le-
gal regulations in force concerning transportation of dangerous goods
Residual emptying: according to VPA 4 Standard recommendation without obligation. Issued by Verband der Chemischen Industrie e.V.
Status: June 2013 Packaging Handbook
27
Chapter 4 Container
Section 4.4 Cylindrical steel drum – removable head
(open head)
4.4.3.2 30 L - Steel drum – removable head (open head) / for solids (based on DIN EN 13008) Measurements and tolerances in mm Total outer height: 580 max. Outer diameter over clamp ring: 305 (±2)
Inner diameter: 280 (+1/-0.5) Minimum wall thickness: according to licensing requirements Nominal capacity: 30 L Brimful capacity (min.): 30 L Color: blue (RAL 5010) Material: steel (EN 10130) Handles: 2 drop handles, sideways (DIN 6646, lockable, VPA 14) Closures: clamp ring with lever closure, G 2 once or G 2 and G 3/4 in lid alternatively (DIN EN ISO 15750-3) Seals: to be chosen according to product requirements (VPA 2) Technical requirements: triple fold Surface, inside: to bee chosen according to product requirements (e.g. raw, coated, PE-Inliner) Minimum requirements: approved for packaging group I Gross mass: 50 kg min. Approval marking: 1A2 .... ... according to provisions of VPA 6 and respective legal regulations in force concerning transportation of dangerous goods Residual emptying: according to VPA 4 Standard recommendation without obligation. Issued by Verband der Chemischen Industrie e.V.
Status: June 2013 Packaging Handbook
28
Chapter 4 Container
Section 4.5 Conical steel drum – removable head
(open head)
4.5.1.1 120 L - Steel drum – removable head (open head) / for liquids Measurements and tolerances in mm Total outer height: 815 (+4/-2) Outer diameter: 500 max. Inner diameter top: 470 (+1/-0.5) bottom: 435 (±1) Minimum wall thickness: according to licensing requirements Nominal capacity: 120 L Brimful capacity (min.): 121 L Color: blue (RAL 5010) Material: steel (EN 10130) Closures: clamp ring with lever closure, G 2 once or G 2 and G 3/4 in lid alternatively (DIN EN ISO 15750-3) Seals: to bee chosen according to product requirements (VPA 2) Technical requirements: triple fold, stackable, with bead Surface, inside: to be chosen according to product requirements (e.g. raw, coated, PE-Inliner) Minimum requirements: approved for packaging group II minimum inner pressure 100 kPa Approval marking: 1A2 .... ... according to provisions of VPA 6 and respective legal regulations in force concerning transportation of dangerous goods Residual emptying: according to VPA 4 Standard recommendation without obligation. Issued by Verband der Chemischen Industrie e.V.
Status: June 2013 Packaging Handbook
29
Chapter 4 Container
Section 4.5 Conical steel drum – removable head
(open head)
4.5.1.2 120 L - Steel drum – removable head (open head) / for solids Measurements and tolerances in mm Total outer height: 815 (+4/-2) Outer diameter: 500 max. Inner diameter top: 470 (+1/-0.5) bottom: 435 (±1) Minimum wall thickness: according to licensing requirements Nominal capacity: 120 L Brimful capacity (min.): 121 L Color: blue (RAL 5010) Material: steel (EN 10130) Closures: clamp ring with lever closure, G 2 once or G 2 and G 3/4 in lid alternatively (DIN EN ISO 15750-3) Seals: to bee chosen according to product requirements (VPA 2) Technical requirements: triple fold, stackable, with bead Surface, inside: to be chosen according to product requirements (e.g. raw, coated, PE-Inliner) Minimum requirements: approved for packaging group II Approval marking: 1A2 .... ... according to provisions of VPA 6 and respective legal regulations in force concerning transportation of dangerous goods Residual emptying: according to VPA 4
Standard recommendation without obligation. Issued by Verband der Chemischen Industrie e.V.
Status: June 2013 Packaging Handbook
30
Chapter 4 Container
Section 4.5 Conical steel drum – removable head
(open head)
4.5.2.1 60 L - Steel drum – removable head (open head) / for liquids (based on DIN EN 13008) Measurements and tolerances in mm Total outer height: 615 (+4/-2) Outer diameter: 405 max.
Inner diameter top: 370 (+1/-0.5) bottom: 355 (±1) Minimum wall thickness: according to licensing requirements Nominal capacity: 60 L Brimful capacity (min.): 61 L Color: blue (RAL 5010) Material: steel (EN 10130) Handles: 2 drop handles sideways (DIN 6646, lockable, VPA 14) Closures: clamp ring with lever closure, G 2 once or G 2 and G 3/4 in lid alternatively (DIN EN ISO 15750-3) Seals: to bee chosen according to product requirements (VPA 2) Technical requirements: triple fold, stackable, with bead Surface, inside: to be chosen according to product requirements (e.g. raw, coated, PE-Inliner) Minimum requirements: approved for packaging group II minimum inner pressure 100 kPa Approval marking: 1A2 ... according to provisions of VPA 6 and respective legal
regulations in force concerning transportation of dangerous goods
Residual emptying: according to VPA 4 Standard recommendation without obligation. Issued by Verband der Chemischen Industrie e.V.
Status: June 2013 Packaging Handbook
31
Chapter 4 Container
Section 4.5 Conical steel drum – removable head
(open head)
4.5.2.2 60 L - Steel drum – removable head (open head) / for solids (based on DIN EN 13008) Measurements and tolerances in mm Total outer height: 615 (+4/-2) Outer diameter: 405 max.
Inner diameter top: 377 (+1/-0.5) bottom: 355 (±1) Minimum wall thickness: according to licensing requirements Nominal capacity: 60 L Brimful capacity (min.): 61 L Color: blue (RAL 5010) Material: steel (EN 10130) Handles: 2 drop handles sideways (DIN 6646, lockable, VPA 14) Closures: clamp ring with lever closure, G 2 once or G 2 and G 3/4 in lid alternatively (DIN EN ISO 15750-3) Seals: to bee chosen according to product requirements (VPA 2) Technical requirements: triple fold, stackable, with bead Surface, inside: to be chosen according to product requirements (e.g. raw, coated, PE-Inliner) Minimum requirements: approved for packaging group II Approval marking: 1A2 .... ... according to provisions of VPA 6 and respective legal regulations in force concerning transportation of dangerous goods Residual emptying: according to VPA 4
Standard recommendation without obligation. Issued by Verband der Chemischen Industrie e.V.
Status: June 2013 Packaging Handbook
32
Chapter 4 Container
Section 4.5 Conical steel drum – removable head
(open head)
4.5.3.1 30 L - Steel drum – removable head (open head) / for liquids (based on DIN EN 13008) Measurements and tolerances in mm Total outer height: 407 (+4/-2) Outer diameter: 355 max.
Inner diameter top: 328 (+1/-0.5) bottom: 312 (±1) Nominal wall thickness: according to licensing requirements Nominal capacity: 30 L Brimful capacity (min.): 30 L Color: blue (RAL 5010) Material: steel (EN 10130) Handles: 2 drop handles sideways (DIN 6646, lockable, VPA 14) Closures: clamp ring with lever closure, G 2 once or G 2 and G 3/4 in lid alternatively (DIN EN ISO 15750-3) Seals: to bee chosen according to product requirements (VPA 2) Technical requirements: triple fold, stackable, with bead Surface, inside: to be chosen according to product requirements (e.g. raw, coated, PE-Inliner) Minimum requirements: approved for packaging group II minimum inner pressure: 100 kPa Approval marking: 1A2 .... ... according to provisions of VPA 6 and respective legal regulations in force concerning transportation of dangerous goods Residual emptying: according to VPA 4 Standard recommendation without obligation. Issued by Verband der Chemischen Industrie e.V.
Status: June 2013 Packaging Handbook
33
Chapter 4 Container
Section 4.5 Conical steel drum – removable head
(open head)
4.5.3.2 30 L - Steel drum – removable head (open head) / for solids (based on DIN EN 13008) Measurements and tolerances in mm Total outer height: 407 (+4/-2) Outer diameter: 355 max.
Inner diameter top: 328 (+1/-0.5) bottom: 312 (±1) Minimum wall thickness: according to licensing requirements Nominal capacity: 30 L Brimful capacity (min.): 30 L Color: blue (RAL 5010) Material: steel (EN 10130) Handles: 2 drop handles sideways (DIN 6646, lockable, VPA 14) Closures: clamp ring with lever closure, G 2 once or G 2 and G 3/4 in lid alternatively (DIN EN ISO 15750-3) Seals: to bee chosen according to product requirements (VPA 2) Technical requirements: triple fold, stackable, with bead Surface, inside: to be chosen according to product requirements (e.g. raw, coated, PE-Inliner) Minimum requirements: approved for packaging group II Approval marking: 1A2 .... ... according to provisions of VPA 6 and respective legal regulations in force concerning transportation of dangerous goods Residual emptying: according to VPA 4 Standard recommendation without obligation. Issued by Verband der Chemischen Industrie e.V.
Status: June 2013 Packaging Handbook
34
Chapter 4 Container
Section 4.6 Fiberboard drum – removable head
(open head)
4.6.1.1 200 L - Fiberboard drum – removable head (open head) (based on DIN EN 12710) Measurements and tolerances in mm Total outer height: 874 (±5) Outer diameter: 577 (±3) Inner diameter: 560 (±2) Fill opening: 540 (±2) Mass in g: 7 500 (±400) Nominal capacity: 200 L Brimful capacity (min.): 200 L Color: natural-coloured Material mantle: kraftliner 300 g/m² (±15 g) Material bottom/lid: sheet steel 0.5 mm, galvanized on both sides (EN 10131, restricted tolerances) Closures: clamp ring with lever closure Seals: to be chosen according to product requirements (VPA 2) Technical requirements: water-soluble glue Weather-proof implementation: water-insoluble glue Minimum requirements: approved for packaging group I Gross mass: 208 kg min. Approval marking: 1G .... ... according to provisions of VPA 6 and respective legal
regulations in force concerning transportation of dangerous goods
Residual emptying: according to VPA 4 Standard recommendation without obligation. Issued by Verband der Chemischen Industrie e.V.
Status: June 2013 Packaging Handbook
35
Chapter 4 Container
Section 4.6 Fiberboard drum – removable head
(open head)
4.6.2.1 120 L - Fiberboard drum – removable head (open head) (based on DIN EN 12710)
Measurements and tolerances in mm Total outer height: 689 (±5) Outer diameter: 517 (±3) Inner diameter: 500 (±2) Fill opening: 480 (±2) Mass in g: 5 400 (±270) Nominal capacity: 120 L Brimful capacity (min.): 120 L Color: natural-coloured Material mantle: kraftliner 300 g/m² (±15 g) Material bottom/lid: sheet steel 0.5 mm, galvanized on both sides (EN 10131, restricted tolerances) Closures: clamp ring with lever closure Seals: to be chosen according to product requirements (VPA 2) Technical requirements: water-soluble glue Weather-proof implementation: water-insoluble glue Minimum requirements: approved for packaging group I Gross mass: 125 kg min.
Approval marking: 1G ... according to provisions of VPA 6 and respective legal reg-ulations in force concerning transportation of dangerous goods
Residual emptying: according to VPA 4 Standard recommendation without obligation. Issued by: Verband der Chemischen Industrie e.V.
Status: June 2013 Packaging Handbook
36
Chapter 4 Container
Section 4.6 Fiberboard drum – removable head
(open head)
4.6.3.1 60 L - Fiberboard drum (based on DIN EN 12710) Measurements and tolerances in mm Total outer height: 623 (±5) Outer diameter: 382 (±3) Inner diameter: 375 (±2) Fill opening: 355 (±2) Mass in g: 3 300 (±175) Nominal capacity: 60 L Brimful capacity (min.): 60 L Color: natural-coloured Material mantle: kraftliner 300 g/m² (±15 g) Material bottom/lid: sheet steel 0.5 mm, galvanized on both sides (EN 10131, restricted tolerances) Closures: clamp ring with lever closure Seals: to be chosen according to product requirements (VPA 2) Technical requirements: water-soluble glue Weather-proof implementation: water-insoluble glue Minimum requirements: approved for packaging group I Gross mass: 75 kg min. Approval marking: 1G .... ... according to provisions of VPA 6 and respective legal
regulations in force concerning transportation of dangerous goods
Residual emptying: according to VPA 4
Standard recommendation without obligation. Issued by Verband der Chemischen Industrie e.V.