CHAPTER 16 – CONTROL UNIT OPERATION Andrae Darby Brian McCaul Carlos Estrada Cristina Rodriguez...
-
Upload
gabrielle-check -
Category
Documents
-
view
222 -
download
2
Transcript of CHAPTER 16 – CONTROL UNIT OPERATION Andrae Darby Brian McCaul Carlos Estrada Cristina Rodriguez...
CHAPTER 16 – CONTROL UNIT
OPERATIONAndrae DarbyBrian McCaul
Carlos EstradaCristina Rodriguez
Yuniel Barbon
CONTROL UNIT
The Control Unit can be thought of as the brain of the CPU itself. It controls based on the instructions it decodes, how other parts of the CPU and in turn, rest of the computer systems should work in order that the instruction gets executed in a correct manner.
ADA
MICRO OPERATION(micro-ops or μops)
A computer executes a program
Instruction cycle: made up of smaller units: fetch, indirect, execute and interrupt with only the fetch & execute cycles always being used.
Each cycle has a number of steps see pipelining
Called micro-operations
Each step is very simple
Accomplishes very little
A
MICRO OPERATION(micro-ops or μops)
Micro operations are the functional, or atomic
operations of a processor.
A
MICRO OPERATION(micro-ops or μops)
A
Fetch cycle The fetch cycle occurs at the beginning of each instruction
cycle and causes an instruction to be fetched from memory. The four registers used are:
Memory Address Register (MAR) Connected to address lines of the system bus Specifies address in memory for read or write ops
Memory Buffer Register (MBR) Connected to data lines of the system bus Contains last value to be stored in
or read from memory
Program Counter (PC) Holds the address of next instruction to be fetched
Instruction Register (IR) Holds the last instruction fetched
A
Fetch Sequence
Address of next instruction is in PC
Address (MAR) is placed on address bus
Control unit issues READ command
Result (data from memory) appears on data bus
Data from data bus copied into MBR
PC incremented by 1 (in parallel with data fetch from memory)
Data (instruction) moved from MBR to IR
MBR is now free for further data fetches
A
Fetch Sequence
t1: MAR <- (PC)
t2: MBR <- (memory)
PC <- (PC) +I
t3: IR <- (MBR)
(tx = time unit/clock cycle) or
t1: MAR <- (PC)
t2: MBR <- (memory)
t3: PC <- (PC) +1
IR <- (MBR)
A
Rules for Grouping Micro Operations
Proper sequence must be followed MAR <- (PC) must precede MBR <- (memory)
Conflicts must be avoided Must not read & write from the same register in one time
unit.
For example: MBR <- (memory) & IR <- (MBR) must not be in same cycle
Also: PC <- (PC) +I involves addition. To avoid duplication of circuitry. Use ALU to perform this addition The use of the ALU may use additional micro-operations
A
Questions
What is the control unit?
Which instruction cycle is always used?
The Indirect Cycle
Happens after the fetch cycle, and fetches source operands
Step 1: MAR (IR(Address))
Address field of the instruction to Memory Address Register
• Step 2: MBR Memory
Fetches the address of the operand and places in MBR
• Step 3: IR(Address) (MBR(Address))
Direct address from MBR to Instruction Register
• The IR is now in the same state as if indirect addressing had not been used
BM
The Interrupt Cycle Happens when a test determines an enabled interrupt has occurred
after the execute cycle.
Step 1: MBR (PC)
Move Program Counter contents to Memory Buffer Register
Step 2: MAR Save_Address PC Routine_Address
Saved address of the stored PC to Memory Address Register and address of new interrupt routine to Program
Counter
• Step 3: Memory (MBR)
Move Memory Buffer Register contents to Memory
• This is the minimum and may require additional micro-operations
BM
The Execute Cycle (ADD)
There is a different sequence of micro operations for each op code.
Example: An Add Instruction
ADD R1, X (This adds contents of X to R1)
Might proceed like so:
• Step 1: MAR (IR(Address))
• Step 2: MBR Memory
• Step 3: R1 (R1) + (MBR)
BM
The Execute Cycle (ISZ)
ISZ X
Increments the location of X by 1 and if the result if zero then the next instruction is skipped.
Step 1: MAR (IR(Address))
Step 2: MBR Memory
Step 3: MBR (MBR) + 1
Step 4: Memory (MBR)
If ((MBR) = 0 ) then (PC (PC) + I )
BM
The Execute Cycle (BSA)
BSA X
Branch and Save address instruction
Address of instruction following BSA instruction is saved in X and execution continues at location X+1. X will later be used for return
Step 1: MAR (IR(Address)) MBR (PC)
Step 2: PC (IR(Address)) Memory (MBR)
Step 3: PC (PC) + I
BM
The Instruction Cycle
Each Phase of the Instruction Cycle can be decomposed into a sequence of elementary micro-operations
Ex: one sequence each for fetch, indirect, interrupt, and in the execute cycle, one sequence per op code.
We need to tie sequences of micro-operations together, and we so this by assuming a new 2-bit register, the Instruction Cycle Code (ICC). It designates the state of the processor by the cycle it is in as follows: 00:Fetch 01:Indirect 10:Execute 11:Interrupt
BM
The Instruction Cycle (Cont.) The following flowchart shows the sequence of micro-
operations
BM
Questions
How many bits is the ICC register?
Does the sequence of micro-operations on the execute cycle depend on the opcode?
Control Of The Processor
Characterization of the control unit
Define the basic elements of the processor.
Describe the micro-operations that the processor performs.
Determines the function that the control unit must perform to cause the micro-operations to be performed.
CE
Basic elements of processor:ALU (functional essence of the computer)
Registers (Store data internal to the processor. Contain info needed to manage instruction sequencing. Contain data that go or come from the ALU, memory, and I/O modules)
Internal data paths (move data between registers and between ALU)
Internal data paths (Link registers to memory and I/O modules by means of a bus)
Control unit (Causes operations to happen within the processor)
CE
Sequence of micro-operations
Transfer data from one register to another
Transfer data from a register to an external interface
Transfer data from an external interface to a register
Perform an arithmetic or logic operation, using registers for input and output
CE
Control Unit Functions
Sequencing: control unit causes the processor to step through a series of micro-operations in sequence, based on the program being executed
Execution: control unit causes each micro-operation to be performed
CE
Control Signals
Control Unit Block Diagram
CE
Control Unit Inputs
Clock: control unit causes one micro-operation (or set of simultaneous micro-operations)
Instruction register: opcode of the current instruction is used to determine which micro-operations to perform during the execute cycle
Flags: needed by the control unit to determine the status of the processor and the outcome of previous ALU operations
Control signals from control bus: Provides signals to the control unit (interrupt, acknowledgement)
CE
Control Unit Outputs
Control signal within the processor: (type 1): cause data to be moved from one register to another. (type 2): activate ALU function.
Control signals to control bus: (type 1): control signals to memory. (type 2): control signals to the I/O modules.
CE
Control Unit and the Fetch Cycle
MAR <- (PC)
control unit activates the control signal that opens the gates between the bits of the PC and the bits of the MAR.
MBR <- (memory)
control signal opens gates, allowing MAR contents onto bus
memory read signal to bus
contents of data bus stored in MBR
signal to logic that increment PC and store the result back to PC
CE
Data Paths and Control Signals
CE
Questions
The control unit performs which 2 basic tasks?
What is sequencing and execution?
Internal Processor Organization
Usually a single internal bus
Gates control movement of data onto and off the bus
Control signals control data transfer to and from external systems bus
Temporary registers needed for proper operation of ALU
CR
CPU withInternalBus
NOTE: A single internal bus connects the ALU and all the processor registers
CR
Internal Processor Organization
Movement of data onto and off the bus from each is register possible through gates and control signals
New registers: Y and Z Aid in operation of ALU Source for additional operands; temporary storage
(Y input storage; Z output storage)
ALU: combinational circuit (output is a pure function of the present input only)
Control signals activate ALU function input is transformed to output (register Z is the temporary output; ALU output is NOT connected directly to BUS)
CR
Intel 8085
Other components in this processor: Incrementer/decrementer address latch avoids
use of ALU for incrementing SP or PC Interrupt control handles interrupt signalsSerial I/O control interfaces to devices
CR
Intel 8085 CPU Block Diagram
CR
Intel 8085 Pin
Configuration
External signals into and out of the 8085 are linked to the external system bus. These signals interface the processor and the rest of the system.
CR
External Signals Address and Data Signals
High Address (A15-A8) Address/Data (AD7-AD0) Serial Input Data (SID) Serial Output Data (SOD)
Timing and Control Signals CLK (OUT) X1, X2 Address Latch Enable
(ALE) Status (S0, S1) IO/M Read Control (RD) Write Control (WR)
Memory and I/O Initiated Symbols Hold Held Acknowledge
(HOLDA) READY
Interrupt-Related Signals TRAP Interrupt Request (INTR) Interrupt Acknowledge
CPU Initialization RESET IN REST OUT
Voltage and Ground
CR
Intel 8085 OUT Instruction Timing Diagram
CR
8085 Timing
The timing of processor operations is synchronized by the clock and controlled by the control unit with control signals.
Timing diagram shows the value of external control signals. Three machine cycles (3-5 states per machine cycle) are shown.
The Address Latch Enable (ALE) signals the start of each machine cycle from the control unit.
Must give enough time for signal level to stabilize.
CR
Questions
What are the temporary registers which aid in ALU operation?
What controls data transfer to and from external bus?
First Programmable Computer
Z1 began development in 1936 by Germany’s Konrad Zuse
Considered the first electrical binary programmable computer
64-word memory (each word contained 22 bits), a total of 176 bytes memory and a clock speed of 1 Hz
Program through punch tape/output through punch tape
YB
The Z1
Beginning of Binary Operations
George Boole wanting a rapid development in electrical technology discovered logic functions
At that time all operations were done by opening and closing a switch
He realized that a combination of switches can bring out a new world of logical operations which he called binary logic
Boole also arrived to Boolean Algebra to solve this operations
YB
AND Switch Circuit
OR Switch Circuit
NOT Switch Circuit
Hardwired Implementation (1)
Control Unit Key Inputs are: instruction register, the clock, flags, and control bus signal
Flags and control bus are directly useful to the CU Each bit means something
Instruction register Provides Op-code’s that the CU uses for instructions for
actions CU logic simplified by decoder which takes an encode
signal and produces a single output
YB
Hardwired Implementation (2)
ClockRepetitive sequence of pulsesUseful for measuring duration of micro-opsMust be long enough to allow signal propagationDifferent control signals at different times within instruction
cycleNeed a counter with different control signals for t1, t2 etc.
YB
Control Unit with Decoded Inputs
Control Unit LogicProcessor’s use Boolean equations to define the control
unit
Control Unit controls the state of instruction cycle
Controls the timing generator to reset at the end of each subcycle
Subcycle Fetch Indirect Execute Interrupt
YB
Example of Boolean Equations
Consider the following interpretation PQ = 00 Fetch Cycle PQ = 01 Indirect Cycle PQ = 10 Execute Cycle PQ = 11 Interrupt Cycle
Then if this expression defines C5: C5 = P*Q*T2 + P*q*T2 This means that the control signal C5 will be asserted
during the second time unit of both the fetch and indirect cycles
YB
Problems With Hard Wired Designs
Complex sequencing & micro-operation logic
Difficult to design and test
Inflexible design
Difficult to add new instructions
YB
Questions
What are the 4 subcycles of a control unit?
What are the 4 key inputs of a control unit?
Additional Information
Intel 8080:
http://en.wikipedia.org/wiki/Intel_8080
Processor Organization:
http://www.cs.trinity.edu/About/The_Courses/cs301/02.computer.organization/02.comp.org.html
http://dsrg.mff.cuni.cz/~ceres/sch/osy/text/ch01s03s02.php