CFS CAT57164 - ikont.co.jp · very compact; stud dia. of 1.4mm to 6 mm and outside dia. of outer...

CAT-57164June 2008 Overseas Dept.

CAT-57164June 2008 Overseas Dept.

Structure

Size Variations

New and Wide Variations of Miniature Type Cam Followers

Metric Series CF Miniature Series CFS

CF···BUU

CF···WBUUR CFS···W

CFS

CFS

CFS

CF

CF

CFS···V

CF 3

10 12 13

12108654.54

65432.521.4

CF 4

CFS 4 CFS 5 CFS 6CFS 3CFS 2.5CFS 2CFS 1.4

CF 5

This is a miniature version of metric series CF which is the basic type of Cam Follower. Various shapes and sizes are available.

21

Miniature Type Cam Follower series meets miniaturization demands of advanced equipment.

Outer Ring Needle Roller

Stud

Thrust Washers

Hexagon Nut

1.4mmMicro Cam Follower CF1.4WV of stud dia. of 1.4 mm and outside dia. of outer ring of only 4 mm The built-in thrust washers receive axial loads that may occur due to mounting errors.

Five major features

Seal Cage

Thrust Washer Thrust Washer

Cage Cage

Cage

Seal

Stud

Stud Stud

Stud

End Plate

Needle Roller

Outer Ring

End Plate

Needle RollerOuter RingOuter Ring End Plate

Needle Roller

End Plate

Needle Roller

Outer Ring

Stud

End Plate

Needle Roller

Outer Ring

This series has extremely fine needle rollers assembled in the outer ring so that the outside dia. of outer ring is not so great in comparison with the stud dia.. Cam Followers of this series are used for electronic parts/device, OA equipment, small indexing equipment and so on. Standard Type Cam Follower

Cam Follower with Thrust Washers Miniature Type Cam Follower with Thrust Washers

Miniature Type Cam Follower

Metric Series CF

Metric Series CF

Miniature Series CFS

Miniature Series CFS

1 2 3 4 5CFS1.4WV

Resistant to mounting errorsCam Follower with

Thrust Washers

Debut of smallest Cam Followers in the world with a stud dia. of only 1.4 mm

Stud dia. of only 1.4 mm

Outside dia. of outer ring of only 4 mm

With a hexagon socket hole for easy mounting

Full Complement type of great load capacity

With thrust washers resistant to mounting errors

Stud dia. of only 1.4 mm

Outside dia. of outer ring of only 4 mm

With a hexagon socket hole for easy mounting

Full Complement type of great load capacity

With thrust washers resistant to mounting errors

TypeCaged or

Full complementSeal

structureMaterial Model codeShape of outer ring

Stud diameter(mm)

Shape ofstud head

Miniature Type Cam Followers series are designed to be

very compact; stud dia. of 1.4mm to 6 mm and outside dia. of

outer ring of 4 mm to 13 mm. This series is suitable for light-

loaded high-accuracy cam mechanisms and linear motion

follower bearings. This series can be used in very wide fields

such as equipment for electronic parts, precision measuring

devices, and office appliance.

Cam Followers with Thrust Washer has particular plastic thrust

washers of high wear and heat resistances in the thrust

contact parts between the outer ring and the stud head (and

between the outer ring and the end plate). The washers

receive axial loads of the outer ring due to mounting errors

and prevent friction and abrasion of the sliding surface.

Stainless Steel Made Cam Followers excels at corrosion resis-

tance and is also available in oil-inhibited areas, water-mist

environment and clean room.

Outside dia.of outer ring

D (mm)

Outside dia.of outer ring

D (mm)

Stud dia.d1 (mm)

Standard Type Cam Follower

Cam Follower with Thrust Washers

3 – 5

3 – 5

3 – 5

3 – 5

3 – 5

3 – 5

3 – 5

3 – 5

3 – 5

3 – 5

3 – 5

3 – 5

CF···BR

CF···BUUR

CF···B

CF···BUU

CF···FBR

CF···FBUUR

CF···FB

CF···FBUU

CF···WBR

CF···WBUUR

CF···FWBR

CF···FWBUUR

Shield type

Sealed type

Shield type

Sealed type

Shield type

Sealed type

Shield type

Sealed type

Shield type

Sealed type

Shield type

Sealed type

Crowned outer ring

Cylindrical outer ring

Crowned outer ring


Crowned outer ring

Crowned outer ring

Hex socket

Hex socket

High carbon steel

Stainless steel

High carbon steel

Stainless steel

Caged

Caged

Miniature Type Cam Follower

Miniature Type Cam Follower with Thrust Washers

2 – 6

2 – 6

2 – 6

2 – 6

2 – 6

2 – 6

1.4

CFS

CFS···F

CFS···V

CFS···FV

CFS···W

CFS···FW

CFS···WV

Shield type

Shield type

Shield type

Shield type

Shield type

Shield type

Shield type








Hex socket

Hex socket

High carbon steel

Stainless steel

High carbon steel

Stainless steel

High carbon steel

Stainless steel

High carbon steel

Caged

Full complement

Caged

Full complement

∆DmpSingle plane mean outside dia. deviation

Examples of identification number

Example of Thrust Disk Type Cam Followers

Example of Miniature Type Cam Followers

CF 5

3 F

W

V

B UU R

P6CFS

Identification Number

3

The identification number examples of Miniature TypeCam Followers are shown below.

4

Accuracy

Tolerances of Miniature Type Cam Followers series areshown in table 1, Table 2.1 and Table 2.2.

Fit

The recommended tolerance of mounting hole for the stud isH7 for Metric Series CF and H6 for Miniature Series CFS.The mounting hole diameter should be prepared without playbetween the stud and the hole especially when heavy shockloads may be applied.

Maximum Allowable Load

The applicable load on Cam Followers is, in some cases,limited by the bending strength and shear strength of the studand the strength of the outer ring instead of the load rating ofthe needle roller bearing. Therefore, the maximum allowablestatic load is specified by the limitations of those strengths.

Type

Dimensionsand symbols

Metric series CF

Crownedouter ring

0

－50

h7

0

－120

0

－120

h6

See Table2.1

See Table 2.2

Cylindricalouter ring

Miniature seriesCFS

Table 1 Tolerances unit: μm

Out side dia. of outerring

Stud dia. d1

Width of outer ring C

∆DmpSingle planemean outsidedia. deviation

High Low

0 －8

VDp

Outside dia.variation in asingle radial

plane

10 6 15

VDmp

Mean outsidedia. variation

Kea

Radial runoutof assembledbearing outer

ring

Table 2.1 Accuracy of outer ring(for cylindrical outer ring of Metric series CF)

unit: μm

class 0 class 6 class 5 class 4 class 0 class 6 class 5 class 4

High Low High Low High Low High Low

0 －8 0 －7 0 －5 0 －4 15 8 5 4

KeaRadial runout of

assembled bearingouter ring

Table 2.2 Accuracy of outer ring(for Miniature series CFS) unit: μm

Model code(1)

Metric series CF

CF3～CF5

―

Miniature series CFS

CFS1.4～CFS5

CFS6

Radial internalclearance

Min.

3

5

Max.

17

20

Table 3 Radial internal clearance unit: μm

Note(1) Only representative types are shown in the table, but applicableto all metric series.

Nominal outside dia.of stud

mm

H6 H7

over incl High Low High Low

―

3

3

6

＋6

＋8

0

0

＋10

＋12

0

0

Table 4 Tolerances of mounting hole unit: μm

Clearances

Internal clearances of Miniature Type Cam Followers series are

shown in Table 3.

Model code

Metric SeriesCF

MiniatureSeries CFS

Standard Type CamFollowers

Thrust Disk Type CamFollowers

Miniature Type CamFollowers

Thrust Disk Type MiniatureCam Followers

CF

CF…W

CFS

CFS…W

Size

Stud dia. (Unit: mm)

Material code

No symbol

F

Carbon steel

Stainless steel

Roller guiding method

No symbol

V

Caged type

Full complement type

Shape of stud head

B

No symbol

With Hexagon Hole (CF series)

With Hexagon Hole (CFS series)

Seal structure

No symbol

UU

Shield type

Sealed type

Shape of outer ring

R

No symbol

Crowned outer ring


Accuracy class

No symbol

P6

P5

P4

Accuracy class / class 0




Applicable toMiniatureSeries CFS

1N=0.102kgf=0.2248lbs.1mm=0.03937inch

65

Allowable RotationalSpeed

Track Capacity Lubrication Hole

Mounting

Metric series CF having a stud dia. 5mm has an oil hole in the

stud-head. Cam Follower with a hexagon hole in the stud-head is

applied through the lubrication plug inside of the hexagon hole in

the stud-head. (See Fig. 1)

For replenishing of grease, mount an appropriate supply nozzle

(shown in Table 9) on the straight type grease gun of JIS B9808

(1991), push the nozzle against the grease nipple and the

lubrication plug, and gently apply the grease. Structurally, other

Metric series CF and Miniature series CFS cannot be re-lubricated.

Accessories

In Miniature Type Cam Followers series, nuts are attached.Track capacity is defined as a load which can be continuously

applied on a Cam Follower placed on a steel track surface without

causing deformation or indentation on the track surface when the

outer ring of the Cam Follower makes contact with the mating track

surface (plane). The track capacities shown in Table 5 are

applicable when the hardness of the mating track surface is 40HRC

(Tensile strength 1250N/mm2). When the hardness of the mating

track surface differs from 40HRC, the track capacity is obtained by

multiplying the value by the track capacity factor shown in Table 6.

If lubrication between the outer ring and the mating track surface is

insufficient, seizure and/or wear may occur depending on the

application. Therefore, attention must be paid to the lubrication and

the surface roughness of the mating track especially for high-speed

operation such as cam mechanisms.

Type(1)

Metric seriesCF

Miniatureseries CFS

Model codeCrownedouter ring

CF 3 R

CF 4 R

CF 5 R

―

―

―

―

―

―

―

542

712

794

―

―

―

―

―

―

―

CF 3

CF 4

CF 5

CFS 1.4

CFS 2

CFS 2.5

CFS 3

CFS 4

CFS 5

CFS 6

1 360

1 790

2 210

128

220

298

485

799

1 210

1 680

Trackcapacity

Model codeCylindricalouter ring

Trackcapacity

Table 5 Track capacity unit: N

Note(1) Only representative types are shown in the table, but applicableto all metric series.

HardnessTensile strength

N／mm2

Track capacity factor

Crowned outer ring Cylindrical outer ring

20

25

30

35

38

40

42

44

46

48

50

52

54

56

58

760

840

950

1 080

1 180

1 250

1 340

1 435

1 530

1 635

1 760

1 880

2 015

2 150

2 290

0.22

0.31

0.45

0.65

0.85

1.00

1.23

1.52

1.85

2.27

2.80

3.46

4.21

5.13

6.26

0.37

0.46

0.58

0.75

0.89

1.00

1.15

1.32

1.51

1.73

1.99

2.29

2.61

2.97

3.39

Table 6 Track capacity factor

The allowable rotational speed of Miniature Type Cam Followers

series are affected by mounting and operating conditions. For

reference, Table 7 shows d1n values when only pure radial loads

are applied. Considering that axial loads also act under actual

operating conditions, the recommended d1n value is 1/10 of the

value shown in the table.

Pre-Packed Grease andOperating Temperature

Grease pre-packed Miniature Type Cam Followers series is

ALVANIA GREASE S2 (SHELL), which can be used within the

temperature range shown in Table 8.

Lubricant

Type

Caged type

Full complement type

84 000

42 000

Grease

Table 7 d1n values of Miniature Type Cam Followersseries

Note d1n value ＝d1×n

where, d1：Stud diameter mmn：Rotational speed rpm

Type

Size of stud dia.d1 mm

Caged type Fullcomplement

typeShieldtype

Sealedtype

Metric seriesCF

Carbon steel

Stainlesssteel

3, 4－ 20°C～

110°C(1)－ 20°C～

80°C

－ 20°C～80°C

―－ 20°C～

120°C

―

―

－ 20°C～120°C

―

―

―

－ 20°C～120°C

－ 20°C～120°C

－ 20°C～110°C(1)

－ 20°C～120°C

5

－ 20°C～80°C

―－ 20°C～

110°C(1)3～5

1.4

2

2.5～6

Miniature series CFS

Table 8 Operating temperature range

Note(1) The maximum allowable temperature is +100˚C when they arecontinuously operated.

qSet the center axis of the mounting hole perpendicularly to the

moving direction of the Cam Follower and match the side shoulder

accurately with the seating surface indicated by dimension “ f ” in

the dimension tables. (See Fig.2) Then, fix the Cam Followers

directly with a hammer, etc. This may lead to a bearing failure such

as irregular rotation or cracking.

Fig.2 Seating surface

ƒ

Lubrication plug

Fig.1 Oil hole position

wThe mark on the stud-head indicates the position of oil

hole on the raceway. Avoid locating the oil hole within the loading

zone. This may lead to short a bearing life. (Refer to Fig.3)

eWhen tightening the nut, the tightening torque should not exceed

the values shown in the dimension tables. If the tightening torque

is too large, it is possible that the threaded portion of the stud can

be broken. When there is a possibility of loosening, a special nut

such as a lock nut, spring washer or self-locking nut should be

used.

Oil hole

Load

Fig.3 Oil hole position and loading direction

Type Shape and dimensionApplicable

grease nipple orlubrication plug

Lubricationplug(1)

A-5126T

φ1.

5

PT1/8

29

φ5

126

17°

Width across flats 12

Width acrossflats 12

Note(1) HSP-3 (by Yamada Corp.) is also available to lubricate.Remark Supply nozzles shown in the table can be mounted on the main

body of a common grease gun available on the market (shownbelow). If these supply nozzles are required, consult byspecifying the supply nozzle type.

Table 9 Applicable supply nozzles

Main body of grease gun

Supply nozzle

1N=0.102kgf=0.2248lbs.1mm=0.03937inch

1N=0.102kgf=0.2248lbs.1mm=0.03937inch

8

9

10

17

20

23

9

11

13

0.5

0.5

0.5

2

2.5

3

0.2

0.3

0.3

6.8

8.3

9.3

0.34

0.78

1.6

1 500

1 200

2 070

1 650

2 520

1 930

1 020

813

1 590

1 270

2 140

1 730

384

384

834

834

1 260

1 260

Mountingdimension

f

Min.

mm

Maximumtightening torque

N・m

Basic dynamicload rating

C

N

Basic staticload rating

C0

N

Maximumallowable load

NB B1 B2 C1 H rsmin(3)

Stud dia.

mm

3

4

5

Identification number Mass(Ref.)

g

Boundary dimensions mm

Shield type

Crownedouter ring

CF 3 BR

CF 3 FBR

CF 4 BR

CF 4 FBR

CF 5 BR

CF 5 FBR

CF 3 B

CF 3 FB

CF 4 B

CF 4 FB

CF 5 B

CF 5 FB

CF 3 BUUR

CF 3 FBUUR

CF 4 BUUR

CF 4 FBUUR

CF 5 BUUR

CF 5 FBUUR

CF 3 BUU

CF 3 FBUU

CF 4 BUU

CF 4 FBUU

CF 5 BUU

CF 5 FBUU

4.3

7.4

10.3

10

12

13

7

8

9

3

4

5

M3×0.5

M4×0.7

M5×0.8

5

6

7.5


Crownedouter ring


D C d1 G G1Sealed type

Note(1) Oil hole is not prepared.(2) The stud-head has an oil hole (lubrication plug).(3) Minimum allowable value of chamfer “r ”.

Remark Grease is pre-packed.

87

Standard Type Cam Followers with Hex Head

CF… B (With Cage)CF…FB (With Cage / Stainless steel)

CF… BRCF…FBR

CF… BCF…FB

Stud dia.3.4mm(1)

CF… BUURCF…FBUUR

CF… BUUCF…FBUU

CF 5 BRCF 5 FBR

CF 5 BCF 5 FB

CF 5 BUURCF 5 FBUUR

CF 5 BUUCF 5 FBUU

Stud dia. 5mm(2)

1N=0.102kgf=0.2248lbs.1mm=0.03937inch

8

9

10

17

20

23

9

11

13

0.5

0.5

0.5

2

2.5

3

6.8

8.3

9.3

0.34

0.78

1.6

1 500

1 200

2 070

1 650

2 520

1 930

1 020

813

1 590

1 270

2 140

1 730

384

384

834

834

1 260

1 260

Mountingdimension

f

Min.

mm


N・m


C

N


C0

N


NB B1 B2 C1 H

Stud dia.

mm

3

4

5


g


Shield type

CF 3 WBR

CF 3 FWBR

CF 4 WBR

CF 4 FWBR

CF 5 WBR

CF 5 FWBR

CF 3 WBUUR

CF 3 FWBUUR

CF 4 WBUUR

CF 4 FWBUUR

CF 5 WBUUR

CF 5 FWBUUR

4.3

7.4

10.3

10

12

13

7

8

9

3

4

5

M3×0.5

M4×0.7

M5×0.8

5

6

7.5

D C d1 G G1Sealed type

Note(1) Oil hole is not prepared.(2) The stud-head has an oil hole (lubrication plug).

Remark Grease is pre-packed.

109

Stud dia.3.4mm(1) Stud dia. 5mm(2)

Cam Followers with Thrust Washer / with Hex Head

CF… WB (With Cage)CF…FWB (With Cage / Stainless steel)

CF… WBRCF…FWBR

CF… WBUURCF…FWBUUR

CF 5 WBRCF 5 FWBR

CF 5 WBUURCF 5 FWBUUR

1N=0.102kgf=0.2248lbs.1mm=0.03937inch

Stud dia.

mm

2.5

3

4

5

6


g


With cage Full complement

CFS 2.5―

―CFS 2.5 V

CFS 2 F―

―CFS 2 FV

―CFS 3 V

―CFS 4 V

―CFS 5 V

―CFS 6 V

―CFS 2.5 FV

―CFS 3 FV

―CFS 4 FV

―CFS 5 FV

―CFS 6 FV

CFS 2.5 F―

CFS 2―

―CFS 2 V

CFS 3―

CFS 3 F―

CFS 4―

CFS 4 F―

CFS 5―

CFS 5 F―

CFS 6―

CFS 6 F―

1

2

4

7

13

5

6

8

10

12

3

4

5

6

7

2.5

3

4

5

6

M2.5×0.45

M3 ×0.5

M4 ×0.7

M5 ×0.8

M6 ×1

2.5

3

4

5

6

4.5

5.5

7

8

9.5

D C d1 G G1 B

2 0.6 4.5 2.5 2 M2 ×0.4 2 4

1211

Miniature Type Cam Followers

CFS (With Cage) CFS… V (Full complement)CFS…F (With Cage / Stainless steel) CFS…FV (Full complement / Stainless steel)

B1

B2

C1

G1

d1

GD

C

H

B

Remark Oil hole is not prepared.

Grease is pre-packed.

CFSCFS…F

9.5

11.5

15

18

21.5

5

6

8

10

12

0.7

0.7

1.0

1.0

1.2

0.9

1.3

1.5

2

2.5

4.8

5.8

7.7

9.6

11.6

18.7

33.5

77.7

158

268

288

768

629

1 420

504

1 140

1 120

2 370

897

1 900

1 570

3 180

1 250

2 540

2 090

4 610

1 670

3 690

202

734

611

1 790

488

1 430

1 120

3 000

894

2 400

1 850

4 700

1 480

3 760

2 200

6 250

1 760

5 000

202

229

428

1 000

342

800

351

1 080

281

862

351

360

230

614

161

587

161

229

281

360

484

484

484

484

919

919

894

919

1 570

1 570

1 480

1 570

2 150

2 150

1 760

2 150

Mountingdimension

f

Min.

mm


N・m


C

N


C0

N


NB1 B2 C1 H

CFS…VCFS…FV

8 4 0.7 0.9 4.3 9.1

B1

B2

C1

G1

d1

GD

C

H

B

ƒ

1N=0.102kgf=0.2248lbs.1mm=0.03937inch

481

288

230

428

342

629

504

1120

897

1570

1250

2090

1670

385

202

161

351

281

611

488

1120

894

1850

1480

2200

1760

105

194

161

313

281

399

399

785

785

1370

1370

1920

1760

Mountingdimension

f

Min.

mm


N・cm


C

N


C0

N


NB2 C1 H

3.3

4

5

6

8

10

12

0.7

0.7

0.7

0.7

1

1

1.2

0.9

0.9

0.9

1.3

1.5

2

2.5

3.8

4.3

4.8

5.8

7.7

9.6

11.6

3.0

9.1

18.7

33.5

77.7

158

268

Stud dia.

mm

2.5

3

4

5

6


g


With cage Full complement

―

CFS 2 W

CFS 2 FW

CFS 2.5 W

CFS 2.5 FW

CFS 3 W

CFS 3 FW

CFS 4 W

CFS 4 FW

CFS 5 W

CFS 5 FW

CFS 6 W

CFS 6 FW

CFS 1.4 WV

―

―

―

―

―

―

―

―

―

―

―

―

0.35

0.6

1

2

4

7

13

4

4.5

5

6

8

10

12

1.7

2.5

3

4

5

6

7

1.4

2

2.5

3

4

5

6

M1.4×0.3

M2 ×0.4

M2.5×0.45

M3 ×0.5

M4 ×0.7

M5 ×0.8

M6 ×1

1.4

2

2.5

3

4

5

6

3.7

4.5

5

6.5

8

9

10.5

7

8.5

10

12.5

16

19

22.5

D C d1 G G1 B B1

2

1.4

Remark Oil hole is not prepared.

Grease is pre-packed.

1413

Miniature Cam Followers with Thrust Washer

CFS… W (With Cage) CFS…WV (Full complement)CFS…FW (With Cage / Stainless steel)

CFS… WCFS…FW

B1

B2

C1

G1

d1

GD

C

H

B

ƒ

CFS1.4 WV

Suppresses machine designing and device costs

Minimizes the amount of lubricant andcontributes to the earth environment

Maintenance work can be reduced greatly

Suppresses machine designing and device costs

Minimizes the amount of lubricant andcontributes to the earth environment

Maintenance work can be reduced greatly

Requires no periodical lubrication and

increases the productivity.

Contributes to the earth environment

and reduces the running cost.

Working spaces

can be utilized.

Requires no periodical lubrication and

increases the productivity.

Contributes to the earth environment

and reduces the running cost.

Working spaces

can be utilized.

C-Lube BearingCAT-57165Maintenance Free

“C-Lube bearings” are ’s unique maintenance free bearing products with thermosetting solid lubricant (Capilube) pre-packed in the bearing space.As the bearing rotates, the lubricating oil oozes out onto needle rollers and raceways in proper quantity keeping the lubrication performance for a long period of time.

1

2

3

4

■For shaft support ■For cam mechanisms and follower bearings

C-Lube Machined Type Needle Roller Bearing C-Lube Cam Followers

Outer Ring

Needle Roller

Cage

Stud with Hexagon Socket Hole

With Seals

Thrust Washer

Outer Ring

Cage

C-Lube Unit

Capilube

Capilube

What is your trouble?

Find solutions with

Hard access to lubricating?

Machines and work places are dirty with lubricant?

Lubricating tools and instruments occupy the working places?

Having problems keeping up with lubrication maintenance schedule?

15 16

World Network of

1817

Unit G, 23rd Floor, Zhao Feng World Trade BuildingNo.369, Jiang Su RoadChangning District, Shanghai 200050People's Republic of ChinaPhone: +86 (0)21-5237-9100Fax: +86 (0)21-5237-9095E-mail: [email protected]

East coast

Midwest

West coast

91 Walsh DriveParsippany, NJ 07054U.S.A.Phone: +1 973-402-0254Toll Free: 1-800-922-0337Fax: +1 973-402-0441E-mail : [email protected]

500 East Thorndale AvenueWood Dale, IL 60191U.S.A.Phone: +1 630-766-6464Toll Free: 1-800-323-6694Fax: +1 630-766-6869E-mail : [email protected]

20170 South Western AvenueTorrance, CA 90501U.S.A.Phone: +1 310-609-3988Toll Free: 1-800-252-3665Fax: +1 310-609-3916E-mail : [email protected]

Southeast

Southwest

2150 Boggs Road, Suite 100Duluth, GA 30096U.S.A.Phone: +1 770-418-1904Toll Free: 1-800-874-6445Fax: +1 770-418-9403E-mail : [email protected]

8105 N. Beltline RoadSuite 130, Irving, TX 75063U.S.A.Phone: +1 972-929-1515Toll Free: 1-800-295-7886Fax: +1 972-915-0060E-mail : [email protected]

Head office : 19-19 Takanawa 2-chome Minato-ku Tokyo 108-8586, JapanPhone : +81 (0)3-3448-5850Fax : +81 (0)3-3447-7637E-mail : [email protected] : http://www.ikont.co.jp/eg/Plant : Gifu, Kamakura

ASEAN REPRESENTATIVE OFFICELevel 8, #1 Silom Road, SilomBangrak, BangkokThailand 10500Phone: +66 (0)-2-231-8278Fax: +66 (0)-2-231-8121E-mail: [email protected]

The Netherlands

Germany

Sheffieldstraat 35-393047 AN RotterdamThe NetherlandsPhone: +31 (0)10-4626868Fax: +31 (0)10-4626099E-mail : [email protected]

Mündelheimer Weg 5640472 DüsseldorfGermanyPhone: +49 (0)211-414061Fax: +49 (0)211-427693E-mail : [email protected]

Im Gewerbepark D 3093059 RegensburgGermanyPhone: +49 (0)941-206070Fax: +49 (0)941-2060719E-mail : [email protected]

Gruben Str.95c66540 NeunkirchenGermanyPhone: +49 (0)6821-999-860Fax: +49 (0)6821-999-8626E-mail : [email protected]

UK

Spain

France

2 Vincent Avenue, CrownhillMilton Keynes Bucks MK8 0ABUnited KingdomPhone: +44 (0)1908-566144Fax: +44 (0)1908-565458E-mail : [email protected]

Autovia Madrid-Barcelona, Km. 43,700Polig. Ind. AIDA, A-8, Ofic. 2, 119200-Azuqueca de HenaresGuadalajara, SpainPhone: +34 949-263390Fax: +34 949-263113E-mail : [email protected]

Roissypole Le Dôme2 rue de La HayeBP 15950 Tremblay en France95733 Roissy C. D. G. CedexFrancePhone: +33 (0)1-48165739Fax: +33 (0)1-48165746E-mail : [email protected]

IKO INTERNATIONAL, INC.NIPPON THOMPSON CO., LTD.

IKO-THOMPSON (SHANGHAI) LTD.

NIPPON THOMPSON EUROPE B.V.

ISO 9001 & 14001 Quality system registration certificate

Recognizing that conservation of the global environment is the top-priority challenge for the world’ s population, will conduct its activities with consideration of the environment as a corporate social responsibility, reduce its negative impact on the environment, and help foster a rich global environment.

http://www.ikont.com/ http://www.ikont.eu/

CFS CAT57164 - ikont.co.jp · very compact; stud dia. of 1.4mm to 6 mm and outside dia. of outer...

Documents

Transcript of CFS CAT57164 - ikont.co.jp · very compact; stud dia. of 1.4mm to 6 mm and outside dia. of outer...