Caterpillar Electronic Technician 2012C v1.0 Product ... Electronic Technician 2012C v1.0 ......
-
Upload
vuongnguyet -
Category
Documents
-
view
239 -
download
9
Transcript of Caterpillar Electronic Technician 2012C v1.0 Product ... Electronic Technician 2012C v1.0 ......
Caterpillar Electronic Technician 2012C v1.0 Product Status Report
14-Jun-2014 9:56 AM
Product Status Report
Monitor
C9 330D (THX17560)
Logged Diagnostic Codes [Diagnostic Clock = 6973.3311 hours] - C9 330D (THX17560)
Parameter Value
Product ID NBD01439
Equipment ID NBD01439
Comments
Parameter Value
ECM Serial Number 088J2102AJ
Personality Module Part Number 3194357-00
Parameter Value
Equipment ID NBD01439
Engine Serial Number THX17560
ECM Part Number 2622879-01
ECM Serial Number 15886374JM
Personality Module Part Number 3107886-00
Personality Module Release Date JUN07
Personality Module Description 330D-HEX-C9-HI_LRC
Active Event Codes Present Unavailable
Code Description Occ. First Last
1785-10 Intake Manifold Pressure Sensor : Abnormal Rate of Change 51 6702 6972
274- 4 Atmospheric Pressure Sensor : Voltage Below Normal 2 6873 6963
Page 1 of 33
14-Jun-14file://C:\Users\bramurr\Desktop\June Auction\Cat 330DL- P03-2.XML
Logged Event Codes [Diagnostic Clock = 6973.3311 hours] - C9 330D (THX17560)
Active Diagnostic Codes - C9 330D (THX17560)
Active Event Codes - C9 330D (THX17560)
Current Totals - C9 330D (THX17560)
Configuration - C9 330D (THX17560)
Code Description Occ. First Last
E194 (2) High Exhaust Temperature 1 6958 6958
Code Description
No Active Codes
Code Description
No Active Events
Description Value Unit
Engine Lifetime Hours Unavailable hours
Total Operating Hours 6973 hours
Total Fuel 38054 gal
Engine Starts 7494
Lifetime Total Engine Revolutions 636046056 rev
Total Idle Time 1654:00 hours
Total Idle Fuel 1650 gal
Total Max Fuel 93248 gal
Average Load Factor 39 %
Overall Load Factor 40 %
Description Value Unit
Equipment ID NBD01439
Engine Serial Number THX17560
ECM Part Number 2622879-01
ECM Serial Number 15886374JM
Personality Module Part Number 3107886-00
Page 2 of 33
14-Jun-14file://C:\Users\bramurr\Desktop\June Auction\Cat 330DL- P03-2.XML
Injector Trim Calibration - C9 330D (THX17560)
Machine Control 330D/336D
Logged Diagnostic Codes [Diagnostic Clock = 6972 hours] - Machine Control 330D/336D
Personality Module Release Date JUN07
Personality Module Description 330D-HEX-C9-HI_LRC
Rated Power 286 hp at 1800 rpm
Rated Peak Torque 1000 lb-ft at 1400 rpm
Test Spec 0K6787 0K6788
Top Engine Speed Range 1980 - 1980 rpm
Ether Solenoid Configuration Not Installed
FLS -10
FTS 0
Security System Immobilizer Installation Status Disabled or Not Installed
Total Tattletale 2
Injector Serial Number File Version Tattletale
Injector1 000000003B12003821F4 0 0
Injector2 000000003B12003808E1 0 0
Injector3 000000003B1200379631 0 0
Injector4 000000003B12003835FD 0 0
Injector5 000000003B12003823FA 0 0
Injector6 000000003B11957361F9 0 1
Parameter Value
Product ID NBD01439
ECM Part Number 2218874-04
ECM Serial Number 01405465EM
Software Group Part Number 3277424-00
Software Group Release Date JUL2008
Software Group Description 330D HEX CONTROL
Active Diagnostic Codes Present No
Code Description Occ. First Last
167-12 Alternator Charging Voltage Sensor : Failure 3 6386 6387
Page 3 of 33
14-Jun-14file://C:\Users\bramurr\Desktop\June Auction\Cat 330DL- P03-2.XML
Logged Event Codes [Diagnostic Clock = 6972 hours] - Machine Control 330D/336D
Active Diagnostic Codes - Machine Control 330D/336D
Current Totals - Machine Control 330D/336D
2300- 9 Switch Panel : Abnormal Update Rate 13 123 4047
581- 5 Power Shift Solenoid : Current Below Normal 1 3320 3320
Code Description Occ. First Last
E015 (2) High Engine Coolant Temperature Derate 13 4083 6387
E017 (2) High Engine Coolant Temperature Warning 8 4092 6387
E043 (2) Low System Voltage Warning 2 3310 6357
E100 (3) Low Engine Oil Pressure Warning 55 2044 3679
Code Description
No Active Codes
Description Value Unit
Total Operating Hours 6972 hours
Engine Maintenance Hours 6970 hours
Engine Oil Hours 1731 hours
Engine Oil Filter Hours 1731 hours
Engine Coolant Hours 1731 hours
Fuel/ Water Separator Hours 1731 hours
Fuel Filter Hours 1731 hours
Hydraulic Pump Hours 6970 hours
Hydraulic Pilot Oil Filter Hours 1731 hours
Hydraulic Case Drain Oil Filter Hours 1731 hours
Return Hydraulic Oil Filter Hours 1731 hours
Attachment Hydraulic Oil Filter Hours 0 hours
Hydraulic Oil Hours 1731 hours
Final Drive Oil Hours 1731 hours
Swing Drive Oil Hours 1731 hours
Travel Motor Hours 2861 hours
Tool #1 Hours 0 hours
Tool #2 Hours 0 hours
Page 4 of 33
14-Jun-14file://C:\Users\bramurr\Desktop\June Auction\Cat 330DL- P03-2.XML
Configuration - Machine Control 330D/336D
Tool #3 Hours 0 hours
Tool #4 Hours 0 hours
Tool #5 Hours 0 hours
Tool #6 Hours 0 hours
Tool #7 Hours 0 hours
Tool #8 Hours 0 hours
Tool #9 Hours 0 hours
Tool #10 Hours 0 hours
Return Hydraulic Oil Filter Bypass Hours 249.6 hours
Return Hydraulic Oil Filter Bypass at Cold Temperature Hours 19.6 hours
Hours of Operation at High Hydraulic Pressure 212.7 hours
Hours of Operation at Relief Hydraulic Pressure 50.1 hours
Description Value Unit
Product ID NBD01439
Hydraulic Power Mode High
Fuel Economy Mode Enable Status Enabled
Economy Mode Off
Travel Alarm Installation Status Installed
Water Separator Level Switch ConfigurationNormally Closed (to Ground)
Fuel Filter Differential Pressure Switch Config Not Installed
Secondary Fuel Filter Differential Pressure Switch Config Not Installed
Attachment Hydraulic Oil Filter Switch Configuration Not Installed
Auto Lube Warning Indicator Enable Switch Configuration Not Installed
Machine Overload Pressure Sensor Installation Not Installed
Machine Overload Pressure Threshold Disabled or Not Installed psi
Heavy Lift System Installation Status Not Installed
Engine Cooling Fan Map High Ambient
Engine Fan Reversing Feature Installation Status Not Installed
Engine Fan Reverse Operation Time Disabled or Not Installed sec
Machine Application Configuration Bucket
Main Pump Flow Limitation Pressure Solenoid Installation Status
Not Installed
Attachment Valve #1 Configuration Not Installed
Attachment Valve #2 Configuration Not Installed
Page 5 of 33
14-Jun-14file://C:\Users\bramurr\Desktop\June Auction\Cat 330DL- P03-2.XML
Attachment Valve #3 Configuration Not Installed
Attachment Valve #4 Configuration Not Installed
Attachment Valve #1 Control Type Configuration Disabled or Not Installed
Attachment Valve #2 Control Type Configuration Disabled or Not Installed
Attachment Valve #3 Control Type Configuration Disabled or Not Installed
Attachment Valve #4 Control Type Configuration Disabled or Not Installed
Attachment Valve #1 Combiner Configuration Not Installed
Auxiliary Circuit Flow Combining Solenoid Installation Status Disabled or Not Installed
Hammer Return to Tank Solenoid Installation Status Disabled or Not Installed
Variable Relief Valve Type Configuration Unavailable
Variable Relief Valve #1 Configuration Disabled or Not Installed
Variable Relief Valve #2 Configuration Disabled or Not Installed
F2 Type Valve Load Sense Pres Sensor Installation Disabled or Not Installed
Joystick Handle Configuration Disabled or Not Installed
Foot Switch Installation Status Disabled or Not Installed
Left Attachment Pedal Installation Status Disabled or Not Installed
Right Attachment Pedal Installation Status Disabled or Not Installed
Left Joystick Switch #1 Control Mode Disabled or Not Installed
Left Joystick Switch #2 Control Mode Disabled or Not Installed
Left Joystick Switch #4 Control Mode Disabled or Not Installed
Right Joystick Switch #1 Control Mode Disabled or Not Installed
Right Joystick Switch #2 Control Mode Disabled or Not Installed
Right Joystick Switch #4 Control Mode Disabled or Not Installed
Foot Switch Control Mode Disabled or Not Installed
Left Joystick Thumbwheel Control Mode Disabled or Not Installed
Right Joystick Thumbwheel Control Mode Disabled or Not Installed
Left Attachment Pedal Control Mode Disabled or Not Installed
Right Attachment Pedal Control Mode Disabled or Not Installed
Travel Speed Shift Low Delay 0.4 sec
Travel Speed Shift High Delay 0.4 sec
Travel Speed Shift Low Pres 2611 psi
Travel Speed Shift High Pressure 4641 psi
One Touch Engine Speed Setting 1020 rpm
AESC Setting 1300 rpm
AESC Delay Time 5.0 sec
Throttle Dial Position 1 Engine Speed 800 rpm
Throttle Dial Position 2 Engine Speed 1020 rpm
Throttle Dial Position 3 Engine Speed 1160 rpm
Page 6 of 33
14-Jun-14file://C:\Users\bramurr\Desktop\June Auction\Cat 330DL- P03-2.XML
Throttle Dial Position 4 Engine Speed 1300 rpm
Throttle Dial Position 5 Engine Speed 1470 rpm
Throttle Dial Position 6 Engine Speed 1590 rpm
Throttle Dial Position 7 Engine Speed 1700 rpm
Throttle Dial Position 8 Engine Speed 1800 rpm
Throttle Dial Position 9 Engine Speed 1900 rpm
Throttle Dial Position 10 Engine Speed 1980 rpm
Throttle Dial Position 1 Hydraulic System Torque Percentage
20.0 %
Throttle Dial Position 2 Hydraulic System Torque Percentage
35.0 %
Throttle Dial Position 3 Hydraulic System Torque Percentage
45.0 %
Throttle Dial Position 4 Hydraulic System Torque Percentage
69.0 %
Throttle Dial Position 5 Hydraulic System Torque Percentage
78.0 %
Throttle Dial Position 6 Hydraulic System Torque Percentage
84.0 %
Throttle Dial Position 7 Hydraulic System Torque Percentage
84.0 %
Throttle Dial Position 8 Hydraulic System Torque Percentage
84.0 %
Throttle Dial Position 9 Hydraulic System Torque Percentage
92.0 %
Throttle Dial Position 10 Hydraulic System Torque Percentage
100.0 %
Engine Oil Recommended Maintenance Interval 500 hours
Engine Oil Filter Recommended Maintenance Interval 500 hours
Engine Coolant Recommended Maintenance Interval 3000 hours
Fuel/ Water Separator Recommended Maint Interval 500 hours
Fuel Filter Recommended Maintenance Interval 500 hours
Hydraulic Pilot Oil Filter Recommended Maintenance Interval
1000 hours
Hydraulic Case Drain Oil Filter Recommended MI 1000 hours
Return Hyd Oil Filter Recommended Maint Interval 2000 hours
Attachment Hydraulic Oil Filter Recommended Maintenance Interval
0 hours
Final Drive Oil Recommended Maintenance Interval 2000 hours
Hydraulic Oil Recommended Maintenance Interval 2000 hours
Page 7 of 33
14-Jun-14file://C:\Users\bramurr\Desktop\June Auction\Cat 330DL- P03-2.XML
Calibration Status - Machine Control 330D/336D
Swing Drive Oil Recommended Maintenance Interval 1000 hours
Advanced Machine Security System Installation Status Not Installed
Sunday Security System Bypass Start Time Disabled or Not Installed
Sunday Security System Bypass Stop Time Disabled or Not Installed
Monday Security System Bypass Start Time Disabled or Not Installed
Monday Security System Bypass Stop Time Disabled or Not Installed
Tuesday Security System Bypass Start Time Disabled or Not Installed
Tuesday Security System Bypass Stop Time Disabled or Not Installed
Wednesday Security System Bypass Start Time Disabled or Not Installed
Wednesday Security System Bypass Stop Time Disabled or Not Installed
Thursday Security System Bypass Start Time Disabled or Not Installed
Thursday Security System Bypass Stop Time Disabled or Not Installed
Friday Security System Bypass Start Time Disabled or Not Installed
Friday Security System Bypass Stop Time Disabled or Not Installed
Saturday Security System Bypass Start Time Disabled or Not Installed
Saturday Security System Bypass Stop Time Disabled or Not Installed
Crane System Installation Status Not Installed
Undercarriage Length Configuration Disabled or Not Installed
Boom Angle Adjustment Unavailable Deg
Crane Actual Load Adjustment Unavailable pound
Crane Swing Speed Adjustment Unavailable %
AccuGrade System Installation Status Disabled or Not Installed
Hydraulic Cab Riser Installation Status Disabled or Not Installed
Hydraulic Cab Riser Raise Snubbing Angle Gain Disabled or Not Installed
Hydraulic Cab Riser Raise Snubbing Rate Gain Disabled or Not Installed
Hydraulic Cab Riser Lower Snubbing Angle Gain Disabled or Not Installed
Hydraulic Cab Riser Lower Snubbing Rate Gain Disabled or Not Installed
Calibration Status Last Successful Completion
Attachment Valve #1 ExtendNever Calibrated
Never Successfully Calibrated
Attachment Valve #1 RetractNever Calibrated
Never Successfully Calibrated
Attachment Valve #2 ExtendNever Calibrated
Never Successfully Calibrated
Never Never Successfully
Page 8 of 33
14-Jun-14file://C:\Users\bramurr\Desktop\June Auction\Cat 330DL- P03-2.XML
Tool Configuration - Machine Control 330D/336D
Attachment Valve #2 Retract Calibrated Calibrated
Attachment Valve #3 ExtendNever Calibrated
Never Successfully Calibrated
Attachment Valve #3 RetractNever Calibrated
Never Successfully Calibrated
Attachment Valve #4 ExtendNever Calibrated
Never Successfully Calibrated
Attachment Valve #4 RetractNever Calibrated
Never Successfully Calibrated
Engine Cooling Fan Calibration Success 0.4 hours
Engine Speed Calibration Success 0.2 hours
Left Joystick Thumbwheel CalibrationNever Calibrated
Never Successfully Calibrated
Right Joystick Thumbwheel CalibrationNever Calibrated
Never Successfully Calibrated
Left Attachment Pedal CalibrationNever Calibrated
Never Successfully Calibrated
Right Attachment Pedal CalibrationNever Calibrated
Never Successfully Calibrated
PRV - Pressure GaugeNever Calibrated
Never Successfully Calibrated
PRV - Flow Meter for Two Pump Flow CombinedNever Calibrated
Never Successfully Calibrated
PRV - Attachment Valve #1 Flow LimitNever Calibrated
Never Successfully Calibrated
PRV - Combined Attachment Valve Flow LimitNever Calibrated
Never Successfully Calibrated
PRV - Power Shift Pressure Calibration Success 0.2 hours
Boom Cylinder Extend Pilot Pressure Limit Solenoid Cal
Never Calibrated
Never Successfully Calibrated
Stick Cylinder Retract Pilot Pressure Limit Solenoid Cal
Never Calibrated
Never Successfully Calibrated
PRV - Variable Relief Pressure Calibration Solenoid 1
Never Calibrated
Never Successfully Calibrated
PRV - Variable Relief Pressure Calibration Solenoid 2
Never Calibrated
Never Successfully Calibrated
Description Value Unit
Tool Program Name 0 Active
Page 9 of 33
14-Jun-14file://C:\Users\bramurr\Desktop\June Auction\Cat 330DL- P03-2.XML
Maximum Throttle Dial 10
Minimum Throttle Dial Position 1
Underspeed Enable Enabled
Two Pump Flow Combine EnableDisabled or Not Installed
Initial Tool Program Medium Pressure Circuit Main Pump Torque Reduction
Disabled or Not Installed
%
Total Tool Program Medium Pressure Circuit Main Pump Torque Reduction
Disabled or Not Installed
%
One Way/ Two Way Valve ModeDisabled or Not Installed
Variable Relief Valve #1 PressureDisabled or Not Installed
psi
Variable Relief Valve #2 PressureDisabled or Not Installed
psi
F2 Type Valve Max Flow Derate PressureDisabled or Not Installed
psi
F2 Type Valve Flow Derate Start PressureDisabled or Not Installed
psi
F2 Type Valve Flow Derate End PressureDisabled or Not Installed
psi
Multiple Operation Maximum Extend Pilot Pressure for Attachment Valve #1
Disabled or Not Installed
psi
Multiple Operation Maximum Retract Pilot Pressure for Attachment Valve #1
Disabled or Not Installed
psi
Multiple Operation Maximum Extend Pilot Pres for Combined Attachment Valve
Disabled or Not Installed
psi
Multiple Operation Maximum Retract Pilot Pres for Combined Attachment Valve
Disabled or Not Installed
psi
Hydraulic Temperature High Warning Event Threshold 258.8 Deg F
Attachment Valve #1 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #1 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #1 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #1 Maximum Extend PressureDisabled or Not Installed
psi
Attachment Valve #1 Maximum Retract PressureDisabled or Not Installed
psi
Attachment Valve #1 Open TimeDisabled or Not Installed
sec
Page 10 of 33
14-Jun-14file://C:\Users\bramurr\Desktop\June Auction\Cat 330DL- P03-2.XML
Attachment Valve #1 Close TimeDisabled or Not Installed
sec
Attachment Valve #1 Tool Flow DirectionDisabled or Not Installed
Attachment Valve #2 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #2 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #2 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #2 Maximum Extend PressureDisabled or Not Installed
psi
Attachment Valve #2 Maximum Retract PressureDisabled or Not Installed
psi
Attachment Valve #2 Open TimeDisabled or Not Installed
sec
Attachment Valve #2 Close TimeDisabled or Not Installed
sec
Attachment Valve #2 Tool Flow DirectionDisabled or Not Installed
Attachment Valve #3 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #3 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #3 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #3 Maximum Extend PressureDisabled or Not Installed
psi
Attachment Valve #3 Maximum Retract PressureDisabled or Not Installed
psi
Attachment Valve #3 Open TimeDisabled or Not Installed
sec
Attachment Valve #3 Close TimeDisabled or Not Installed
sec
Attachment Valve #3 Tool Flow DirectionDisabled or Not Installed
Attachment Valve #4 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #4 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #4 Nominal PressureDisabled or Not Installed
psi
Page 11 of 33
14-Jun-14file://C:\Users\bramurr\Desktop\June Auction\Cat 330DL- P03-2.XML
Tool Configuration - Machine Control 330D/336D
Attachment Valve #4 Maximum Extend PressureDisabled or Not Installed
psi
Attachment Valve #4 Maximum Retract PressureDisabled or Not Installed
psi
Attachment Valve #4 Open TimeDisabled or Not Installed
sec
Attachment Valve #4 Close TimeDisabled or Not Installed
sec
Attachment Valve #4 Tool Flow DirectionDisabled or Not Installed
Description Value Unit
Tool Program Name 0
Maximum Throttle Dial 10
Minimum Throttle Dial Position 1
Underspeed Enable Enabled
Two Pump Flow Combine EnableDisabled or Not Installed
Initial Tool Program Medium Pressure Circuit Main Pump Torque Reduction
Disabled or Not Installed
%
Total Tool Program Medium Pressure Circuit Main Pump Torque Reduction
Disabled or Not Installed
%
One Way/ Two Way Valve ModeDisabled or Not Installed
Variable Relief Valve #1 PressureDisabled or Not Installed
psi
Variable Relief Valve #2 PressureDisabled or Not Installed
psi
F2 Type Valve Max Flow Derate PressureDisabled or Not Installed
psi
F2 Type Valve Flow Derate Start PressureDisabled or Not Installed
psi
F2 Type Valve Flow Derate End PressureDisabled or Not Installed
psi
Multiple Operation Maximum Extend Pilot Pressure for Attachment Valve #1
Disabled or Not Installed
psi
Multiple Operation Maximum Retract Pilot Pressure for Attachment Valve #1
Disabled or Not Installed
psi
Multiple Operation Maximum Extend Pilot Pres for Combined Disabled or Not
Page 12 of 33
14-Jun-14file://C:\Users\bramurr\Desktop\June Auction\Cat 330DL- P03-2.XML
Attachment Valve Installed psi
Multiple Operation Maximum Retract Pilot Pres for Combined Attachment Valve
Disabled or Not Installed
psi
Hydraulic Temperature High Warning Event Threshold 258.8 Deg F
Attachment Valve #1 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #1 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #1 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #1 Maximum Extend PressureDisabled or Not Installed
psi
Attachment Valve #1 Maximum Retract PressureDisabled or Not Installed
psi
Attachment Valve #1 Open TimeDisabled or Not Installed
sec
Attachment Valve #1 Close TimeDisabled or Not Installed
sec
Attachment Valve #1 Tool Flow DirectionDisabled or Not Installed
Attachment Valve #2 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #2 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #2 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #2 Maximum Extend PressureDisabled or Not Installed
psi
Attachment Valve #2 Maximum Retract PressureDisabled or Not Installed
psi
Attachment Valve #2 Open TimeDisabled or Not Installed
sec
Attachment Valve #2 Close TimeDisabled or Not Installed
sec
Attachment Valve #2 Tool Flow DirectionDisabled or Not Installed
Attachment Valve #3 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #3 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #3 Nominal PressureDisabled or Not Installed
psi
Page 13 of 33
14-Jun-14file://C:\Users\bramurr\Desktop\June Auction\Cat 330DL- P03-2.XML
Tool Configuration - Machine Control 330D/336D
Attachment Valve #3 Maximum Extend PressureDisabled or Not Installed
psi
Attachment Valve #3 Maximum Retract PressureDisabled or Not Installed
psi
Attachment Valve #3 Open TimeDisabled or Not Installed
sec
Attachment Valve #3 Close TimeDisabled or Not Installed
sec
Attachment Valve #3 Tool Flow DirectionDisabled or Not Installed
Attachment Valve #4 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #4 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #4 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #4 Maximum Extend PressureDisabled or Not Installed
psi
Attachment Valve #4 Maximum Retract PressureDisabled or Not Installed
psi
Attachment Valve #4 Open TimeDisabled or Not Installed
sec
Attachment Valve #4 Close TimeDisabled or Not Installed
sec
Attachment Valve #4 Tool Flow DirectionDisabled or Not Installed
Description Value Unit
Tool Program Name 0
Maximum Throttle Dial 10
Minimum Throttle Dial Position 1
Underspeed Enable Enabled
Two Pump Flow Combine EnableDisabled or Not Installed
Initial Tool Program Medium Pressure Circuit Main Pump Torque Reduction
Disabled or Not Installed
%
Total Tool Program Medium Pressure Circuit Main Pump Torque Reduction
Disabled or Not Installed
%
Disabled or Not
Page 14 of 33
14-Jun-14file://C:\Users\bramurr\Desktop\June Auction\Cat 330DL- P03-2.XML
One Way/ Two Way Valve Mode Installed
Variable Relief Valve #1 PressureDisabled or Not Installed
psi
Variable Relief Valve #2 PressureDisabled or Not Installed
psi
F2 Type Valve Max Flow Derate PressureDisabled or Not Installed
psi
F2 Type Valve Flow Derate Start PressureDisabled or Not Installed
psi
F2 Type Valve Flow Derate End PressureDisabled or Not Installed
psi
Multiple Operation Maximum Extend Pilot Pressure for Attachment Valve #1
Disabled or Not Installed
psi
Multiple Operation Maximum Retract Pilot Pressure for Attachment Valve #1
Disabled or Not Installed
psi
Multiple Operation Maximum Extend Pilot Pres for Combined Attachment Valve
Disabled or Not Installed
psi
Multiple Operation Maximum Retract Pilot Pres for Combined Attachment Valve
Disabled or Not Installed
psi
Hydraulic Temperature High Warning Event Threshold 258.8 Deg F
Attachment Valve #1 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #1 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #1 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #1 Maximum Extend PressureDisabled or Not Installed
psi
Attachment Valve #1 Maximum Retract PressureDisabled or Not Installed
psi
Attachment Valve #1 Open TimeDisabled or Not Installed
sec
Attachment Valve #1 Close TimeDisabled or Not Installed
sec
Attachment Valve #1 Tool Flow DirectionDisabled or Not Installed
Attachment Valve #2 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #2 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #2 Nominal PressureDisabled or Not Installed
psi
Page 15 of 33
14-Jun-14file://C:\Users\bramurr\Desktop\June Auction\Cat 330DL- P03-2.XML
Attachment Valve #2 Maximum Extend PressureDisabled or Not Installed
psi
Attachment Valve #2 Maximum Retract PressureDisabled or Not Installed
psi
Attachment Valve #2 Open TimeDisabled or Not Installed
sec
Attachment Valve #2 Close TimeDisabled or Not Installed
sec
Attachment Valve #2 Tool Flow DirectionDisabled or Not Installed
Attachment Valve #3 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #3 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #3 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #3 Maximum Extend PressureDisabled or Not Installed
psi
Attachment Valve #3 Maximum Retract PressureDisabled or Not Installed
psi
Attachment Valve #3 Open TimeDisabled or Not Installed
sec
Attachment Valve #3 Close TimeDisabled or Not Installed
sec
Attachment Valve #3 Tool Flow DirectionDisabled or Not Installed
Attachment Valve #4 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #4 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #4 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #4 Maximum Extend PressureDisabled or Not Installed
psi
Attachment Valve #4 Maximum Retract PressureDisabled or Not Installed
psi
Attachment Valve #4 Open TimeDisabled or Not Installed
sec
Attachment Valve #4 Close TimeDisabled or Not Installed
sec
Attachment Valve #4 Tool Flow DirectionDisabled or Not Installed
Page 16 of 33
14-Jun-14file://C:\Users\bramurr\Desktop\June Auction\Cat 330DL- P03-2.XML
Tool Configuration - Machine Control 330D/336D
Description Value Unit
Tool Program Name 0
Maximum Throttle Dial 10
Minimum Throttle Dial Position 1
Underspeed Enable Enabled
Two Pump Flow Combine EnableDisabled or Not Installed
Initial Tool Program Medium Pressure Circuit Main Pump Torque Reduction
Disabled or Not Installed
%
Total Tool Program Medium Pressure Circuit Main Pump Torque Reduction
Disabled or Not Installed
%
One Way/ Two Way Valve ModeDisabled or Not Installed
Variable Relief Valve #1 PressureDisabled or Not Installed
psi
Variable Relief Valve #2 PressureDisabled or Not Installed
psi
F2 Type Valve Max Flow Derate PressureDisabled or Not Installed
psi
F2 Type Valve Flow Derate Start PressureDisabled or Not Installed
psi
F2 Type Valve Flow Derate End PressureDisabled or Not Installed
psi
Multiple Operation Maximum Extend Pilot Pressure for Attachment Valve #1
Disabled or Not Installed
psi
Multiple Operation Maximum Retract Pilot Pressure for Attachment Valve #1
Disabled or Not Installed
psi
Multiple Operation Maximum Extend Pilot Pres for Combined Attachment Valve
Disabled or Not Installed
psi
Multiple Operation Maximum Retract Pilot Pres for Combined Attachment Valve
Disabled or Not Installed
psi
Hydraulic Temperature High Warning Event Threshold 258.8 Deg F
Attachment Valve #1 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #1 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #1 Nominal PressureDisabled or Not Installed
psi
Page 17 of 33
14-Jun-14file://C:\Users\bramurr\Desktop\June Auction\Cat 330DL- P03-2.XML
Attachment Valve #1 Maximum Extend PressureDisabled or Not Installed
psi
Attachment Valve #1 Maximum Retract PressureDisabled or Not Installed
psi
Attachment Valve #1 Open TimeDisabled or Not Installed
sec
Attachment Valve #1 Close TimeDisabled or Not Installed
sec
Attachment Valve #1 Tool Flow DirectionDisabled or Not Installed
Attachment Valve #2 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #2 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #2 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #2 Maximum Extend PressureDisabled or Not Installed
psi
Attachment Valve #2 Maximum Retract PressureDisabled or Not Installed
psi
Attachment Valve #2 Open TimeDisabled or Not Installed
sec
Attachment Valve #2 Close TimeDisabled or Not Installed
sec
Attachment Valve #2 Tool Flow DirectionDisabled or Not Installed
Attachment Valve #3 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #3 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #3 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #3 Maximum Extend PressureDisabled or Not Installed
psi
Attachment Valve #3 Maximum Retract PressureDisabled or Not Installed
psi
Attachment Valve #3 Open TimeDisabled or Not Installed
sec
Attachment Valve #3 Close TimeDisabled or Not Installed
sec
Attachment Valve #3 Tool Flow DirectionDisabled or Not Installed
Page 18 of 33
14-Jun-14file://C:\Users\bramurr\Desktop\June Auction\Cat 330DL- P03-2.XML
Tool Configuration - Machine Control 330D/336D
Attachment Valve #4 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #4 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #4 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #4 Maximum Extend PressureDisabled or Not Installed
psi
Attachment Valve #4 Maximum Retract PressureDisabled or Not Installed
psi
Attachment Valve #4 Open TimeDisabled or Not Installed
sec
Attachment Valve #4 Close TimeDisabled or Not Installed
sec
Attachment Valve #4 Tool Flow DirectionDisabled or Not Installed
Description Value Unit
Tool Program Name 0
Maximum Throttle Dial 10
Minimum Throttle Dial Position 1
Underspeed Enable Enabled
Two Pump Flow Combine EnableDisabled or Not Installed
Initial Tool Program Medium Pressure Circuit Main Pump Torque Reduction
Disabled or Not Installed
%
Total Tool Program Medium Pressure Circuit Main Pump Torque Reduction
Disabled or Not Installed
%
One Way/ Two Way Valve ModeDisabled or Not Installed
Variable Relief Valve #1 PressureDisabled or Not Installed
psi
Variable Relief Valve #2 PressureDisabled or Not Installed
psi
F2 Type Valve Max Flow Derate PressureDisabled or Not Installed
psi
F2 Type Valve Flow Derate Start PressureDisabled or Not Installed
psi
Disabled or Not
Page 19 of 33
14-Jun-14file://C:\Users\bramurr\Desktop\June Auction\Cat 330DL- P03-2.XML
F2 Type Valve Flow Derate End Pressure Installed psi
Multiple Operation Maximum Extend Pilot Pressure for Attachment Valve #1
Disabled or Not Installed
psi
Multiple Operation Maximum Retract Pilot Pressure for Attachment Valve #1
Disabled or Not Installed
psi
Multiple Operation Maximum Extend Pilot Pres for Combined Attachment Valve
Disabled or Not Installed
psi
Multiple Operation Maximum Retract Pilot Pres for Combined Attachment Valve
Disabled or Not Installed
psi
Hydraulic Temperature High Warning Event Threshold 258.8 Deg F
Attachment Valve #1 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #1 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #1 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #1 Maximum Extend PressureDisabled or Not Installed
psi
Attachment Valve #1 Maximum Retract PressureDisabled or Not Installed
psi
Attachment Valve #1 Open TimeDisabled or Not Installed
sec
Attachment Valve #1 Close TimeDisabled or Not Installed
sec
Attachment Valve #1 Tool Flow DirectionDisabled or Not Installed
Attachment Valve #2 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #2 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #2 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #2 Maximum Extend PressureDisabled or Not Installed
psi
Attachment Valve #2 Maximum Retract PressureDisabled or Not Installed
psi
Attachment Valve #2 Open TimeDisabled or Not Installed
sec
Attachment Valve #2 Close TimeDisabled or Not Installed
sec
Attachment Valve #2 Tool Flow DirectionDisabled or Not Installed
Page 20 of 33
14-Jun-14file://C:\Users\bramurr\Desktop\June Auction\Cat 330DL- P03-2.XML
Tool Configuration - Machine Control 330D/336D
Attachment Valve #3 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #3 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #3 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #3 Maximum Extend PressureDisabled or Not Installed
psi
Attachment Valve #3 Maximum Retract PressureDisabled or Not Installed
psi
Attachment Valve #3 Open TimeDisabled or Not Installed
sec
Attachment Valve #3 Close TimeDisabled or Not Installed
sec
Attachment Valve #3 Tool Flow DirectionDisabled or Not Installed
Attachment Valve #4 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #4 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #4 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #4 Maximum Extend PressureDisabled or Not Installed
psi
Attachment Valve #4 Maximum Retract PressureDisabled or Not Installed
psi
Attachment Valve #4 Open TimeDisabled or Not Installed
sec
Attachment Valve #4 Close TimeDisabled or Not Installed
sec
Attachment Valve #4 Tool Flow DirectionDisabled or Not Installed
Description Value Unit
Tool Program Name 0
Maximum Throttle Dial 10
Minimum Throttle Dial Position 1
Underspeed Enable Enabled
Disabled or Not
Page 21 of 33
14-Jun-14file://C:\Users\bramurr\Desktop\June Auction\Cat 330DL- P03-2.XML
Two Pump Flow Combine Enable Installed
Initial Tool Program Medium Pressure Circuit Main Pump Torque Reduction
Disabled or Not Installed
%
Total Tool Program Medium Pressure Circuit Main Pump Torque Reduction
Disabled or Not Installed
%
One Way/ Two Way Valve ModeDisabled or Not Installed
Variable Relief Valve #1 PressureDisabled or Not Installed
psi
Variable Relief Valve #2 PressureDisabled or Not Installed
psi
F2 Type Valve Max Flow Derate PressureDisabled or Not Installed
psi
F2 Type Valve Flow Derate Start PressureDisabled or Not Installed
psi
F2 Type Valve Flow Derate End PressureDisabled or Not Installed
psi
Multiple Operation Maximum Extend Pilot Pressure for Attachment Valve #1
Disabled or Not Installed
psi
Multiple Operation Maximum Retract Pilot Pressure for Attachment Valve #1
Disabled or Not Installed
psi
Multiple Operation Maximum Extend Pilot Pres for Combined Attachment Valve
Disabled or Not Installed
psi
Multiple Operation Maximum Retract Pilot Pres for Combined Attachment Valve
Disabled or Not Installed
psi
Hydraulic Temperature High Warning Event Threshold 258.8 Deg F
Attachment Valve #1 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #1 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #1 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #1 Maximum Extend PressureDisabled or Not Installed
psi
Attachment Valve #1 Maximum Retract PressureDisabled or Not Installed
psi
Attachment Valve #1 Open TimeDisabled or Not Installed
sec
Attachment Valve #1 Close TimeDisabled or Not Installed
sec
Attachment Valve #1 Tool Flow DirectionDisabled or Not Installed
Page 22 of 33
14-Jun-14file://C:\Users\bramurr\Desktop\June Auction\Cat 330DL- P03-2.XML
Attachment Valve #2 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #2 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #2 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #2 Maximum Extend PressureDisabled or Not Installed
psi
Attachment Valve #2 Maximum Retract PressureDisabled or Not Installed
psi
Attachment Valve #2 Open TimeDisabled or Not Installed
sec
Attachment Valve #2 Close TimeDisabled or Not Installed
sec
Attachment Valve #2 Tool Flow DirectionDisabled or Not Installed
Attachment Valve #3 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #3 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #3 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #3 Maximum Extend PressureDisabled or Not Installed
psi
Attachment Valve #3 Maximum Retract PressureDisabled or Not Installed
psi
Attachment Valve #3 Open TimeDisabled or Not Installed
sec
Attachment Valve #3 Close TimeDisabled or Not Installed
sec
Attachment Valve #3 Tool Flow DirectionDisabled or Not Installed
Attachment Valve #4 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #4 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #4 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #4 Maximum Extend PressureDisabled or Not Installed
psi
Attachment Valve #4 Maximum Retract PressureDisabled or Not Installed
psi
Page 23 of 33
14-Jun-14file://C:\Users\bramurr\Desktop\June Auction\Cat 330DL- P03-2.XML
Tool Configuration - Machine Control 330D/336D
Attachment Valve #4 Open TimeDisabled or Not Installed
sec
Attachment Valve #4 Close TimeDisabled or Not Installed
sec
Attachment Valve #4 Tool Flow DirectionDisabled or Not Installed
Description Value Unit
Tool Program Name 0
Maximum Throttle Dial 10
Minimum Throttle Dial Position 1
Underspeed Enable Enabled
Two Pump Flow Combine EnableDisabled or Not Installed
Initial Tool Program Medium Pressure Circuit Main Pump Torque Reduction
Disabled or Not Installed
%
Total Tool Program Medium Pressure Circuit Main Pump Torque Reduction
Disabled or Not Installed
%
One Way/ Two Way Valve ModeDisabled or Not Installed
Variable Relief Valve #1 PressureDisabled or Not Installed
psi
Variable Relief Valve #2 PressureDisabled or Not Installed
psi
F2 Type Valve Max Flow Derate PressureDisabled or Not Installed
psi
F2 Type Valve Flow Derate Start PressureDisabled or Not Installed
psi
F2 Type Valve Flow Derate End PressureDisabled or Not Installed
psi
Multiple Operation Maximum Extend Pilot Pressure for Attachment Valve #1
Disabled or Not Installed
psi
Multiple Operation Maximum Retract Pilot Pressure for Attachment Valve #1
Disabled or Not Installed
psi
Multiple Operation Maximum Extend Pilot Pres for Combined Attachment Valve
Disabled or Not Installed
psi
Multiple Operation Maximum Retract Pilot Pres for Combined Attachment Valve
Disabled or Not Installed
psi
Hydraulic Temperature High Warning Event Threshold 258.8 Deg F
Page 24 of 33
14-Jun-14file://C:\Users\bramurr\Desktop\June Auction\Cat 330DL- P03-2.XML
Attachment Valve #1 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #1 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #1 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #1 Maximum Extend PressureDisabled or Not Installed
psi
Attachment Valve #1 Maximum Retract PressureDisabled or Not Installed
psi
Attachment Valve #1 Open TimeDisabled or Not Installed
sec
Attachment Valve #1 Close TimeDisabled or Not Installed
sec
Attachment Valve #1 Tool Flow DirectionDisabled or Not Installed
Attachment Valve #2 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #2 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #2 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #2 Maximum Extend PressureDisabled or Not Installed
psi
Attachment Valve #2 Maximum Retract PressureDisabled or Not Installed
psi
Attachment Valve #2 Open TimeDisabled or Not Installed
sec
Attachment Valve #2 Close TimeDisabled or Not Installed
sec
Attachment Valve #2 Tool Flow DirectionDisabled or Not Installed
Attachment Valve #3 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #3 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #3 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #3 Maximum Extend PressureDisabled or Not Installed
psi
Attachment Valve #3 Maximum Retract PressureDisabled or Not Installed
psi
Page 25 of 33
14-Jun-14file://C:\Users\bramurr\Desktop\June Auction\Cat 330DL- P03-2.XML
Tool Configuration - Machine Control 330D/336D
Attachment Valve #3 Open TimeDisabled or Not Installed
sec
Attachment Valve #3 Close TimeDisabled or Not Installed
sec
Attachment Valve #3 Tool Flow DirectionDisabled or Not Installed
Attachment Valve #4 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #4 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #4 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #4 Maximum Extend PressureDisabled or Not Installed
psi
Attachment Valve #4 Maximum Retract PressureDisabled or Not Installed
psi
Attachment Valve #4 Open TimeDisabled or Not Installed
sec
Attachment Valve #4 Close TimeDisabled or Not Installed
sec
Attachment Valve #4 Tool Flow DirectionDisabled or Not Installed
Description Value Unit
Tool Program Name 0
Maximum Throttle Dial 10
Minimum Throttle Dial Position 1
Underspeed Enable Enabled
Two Pump Flow Combine EnableDisabled or Not Installed
Initial Tool Program Medium Pressure Circuit Main Pump Torque Reduction
Disabled or Not Installed
%
Total Tool Program Medium Pressure Circuit Main Pump Torque Reduction
Disabled or Not Installed
%
One Way/ Two Way Valve ModeDisabled or Not Installed
Variable Relief Valve #1 PressureDisabled or Not Installed
psi
Disabled or Not
Page 26 of 33
14-Jun-14file://C:\Users\bramurr\Desktop\June Auction\Cat 330DL- P03-2.XML
Variable Relief Valve #2 Pressure Installed psi
F2 Type Valve Max Flow Derate PressureDisabled or Not Installed
psi
F2 Type Valve Flow Derate Start PressureDisabled or Not Installed
psi
F2 Type Valve Flow Derate End PressureDisabled or Not Installed
psi
Multiple Operation Maximum Extend Pilot Pressure for Attachment Valve #1
Disabled or Not Installed
psi
Multiple Operation Maximum Retract Pilot Pressure for Attachment Valve #1
Disabled or Not Installed
psi
Multiple Operation Maximum Extend Pilot Pres for Combined Attachment Valve
Disabled or Not Installed
psi
Multiple Operation Maximum Retract Pilot Pres for Combined Attachment Valve
Disabled or Not Installed
psi
Hydraulic Temperature High Warning Event Threshold 258.8 Deg F
Attachment Valve #1 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #1 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #1 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #1 Maximum Extend PressureDisabled or Not Installed
psi
Attachment Valve #1 Maximum Retract PressureDisabled or Not Installed
psi
Attachment Valve #1 Open TimeDisabled or Not Installed
sec
Attachment Valve #1 Close TimeDisabled or Not Installed
sec
Attachment Valve #1 Tool Flow DirectionDisabled or Not Installed
Attachment Valve #2 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #2 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #2 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #2 Maximum Extend PressureDisabled or Not Installed
psi
Attachment Valve #2 Maximum Retract PressureDisabled or Not Installed
psi
Page 27 of 33
14-Jun-14file://C:\Users\bramurr\Desktop\June Auction\Cat 330DL- P03-2.XML
Tool Configuration - Machine Control 330D/336D
Attachment Valve #2 Open TimeDisabled or Not Installed
sec
Attachment Valve #2 Close TimeDisabled or Not Installed
sec
Attachment Valve #2 Tool Flow DirectionDisabled or Not Installed
Attachment Valve #3 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #3 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #3 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #3 Maximum Extend PressureDisabled or Not Installed
psi
Attachment Valve #3 Maximum Retract PressureDisabled or Not Installed
psi
Attachment Valve #3 Open TimeDisabled or Not Installed
sec
Attachment Valve #3 Close TimeDisabled or Not Installed
sec
Attachment Valve #3 Tool Flow DirectionDisabled or Not Installed
Attachment Valve #4 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #4 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #4 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #4 Maximum Extend PressureDisabled or Not Installed
psi
Attachment Valve #4 Maximum Retract PressureDisabled or Not Installed
psi
Attachment Valve #4 Open TimeDisabled or Not Installed
sec
Attachment Valve #4 Close TimeDisabled or Not Installed
sec
Attachment Valve #4 Tool Flow DirectionDisabled or Not Installed
Page 28 of 33
14-Jun-14file://C:\Users\bramurr\Desktop\June Auction\Cat 330DL- P03-2.XML
Description Value Unit
Tool Program Name 0
Maximum Throttle Dial 10
Minimum Throttle Dial Position 1
Underspeed Enable Enabled
Two Pump Flow Combine EnableDisabled or Not Installed
Initial Tool Program Medium Pressure Circuit Main Pump Torque Reduction
Disabled or Not Installed
%
Total Tool Program Medium Pressure Circuit Main Pump Torque Reduction
Disabled or Not Installed
%
One Way/ Two Way Valve ModeDisabled or Not Installed
Variable Relief Valve #1 PressureDisabled or Not Installed
psi
Variable Relief Valve #2 PressureDisabled or Not Installed
psi
F2 Type Valve Max Flow Derate PressureDisabled or Not Installed
psi
F2 Type Valve Flow Derate Start PressureDisabled or Not Installed
psi
F2 Type Valve Flow Derate End PressureDisabled or Not Installed
psi
Multiple Operation Maximum Extend Pilot Pressure for Attachment Valve #1
Disabled or Not Installed
psi
Multiple Operation Maximum Retract Pilot Pressure for Attachment Valve #1
Disabled or Not Installed
psi
Multiple Operation Maximum Extend Pilot Pres for Combined Attachment Valve
Disabled or Not Installed
psi
Multiple Operation Maximum Retract Pilot Pres for Combined Attachment Valve
Disabled or Not Installed
psi
Hydraulic Temperature High Warning Event Threshold 258.8 Deg F
Attachment Valve #1 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #1 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #1 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #1 Maximum Extend PressureDisabled or Not Installed
psi
Attachment Valve #1 Maximum Retract PressureDisabled or Not
psi
Page 29 of 33
14-Jun-14file://C:\Users\bramurr\Desktop\June Auction\Cat 330DL- P03-2.XML
Installed
Attachment Valve #1 Open TimeDisabled or Not Installed
sec
Attachment Valve #1 Close TimeDisabled or Not Installed
sec
Attachment Valve #1 Tool Flow DirectionDisabled or Not Installed
Attachment Valve #2 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #2 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #2 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #2 Maximum Extend PressureDisabled or Not Installed
psi
Attachment Valve #2 Maximum Retract PressureDisabled or Not Installed
psi
Attachment Valve #2 Open TimeDisabled or Not Installed
sec
Attachment Valve #2 Close TimeDisabled or Not Installed
sec
Attachment Valve #2 Tool Flow DirectionDisabled or Not Installed
Attachment Valve #3 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #3 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #3 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #3 Maximum Extend PressureDisabled or Not Installed
psi
Attachment Valve #3 Maximum Retract PressureDisabled or Not Installed
psi
Attachment Valve #3 Open TimeDisabled or Not Installed
sec
Attachment Valve #3 Close TimeDisabled or Not Installed
sec
Attachment Valve #3 Tool Flow DirectionDisabled or Not Installed
Attachment Valve #4 Flow SettingDisabled or Not Installed
gal/min
Disabled or Not
Page 30 of 33
14-Jun-14file://C:\Users\bramurr\Desktop\June Auction\Cat 330DL- P03-2.XML
Tool Configuration - Machine Control 330D/336D
Attachment Valve #4 Multi-Oper. Additional Flow Installed gal/min
Valve #4 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #4 Maximum Extend PressureDisabled or Not Installed
psi
Attachment Valve #4 Maximum Retract PressureDisabled or Not Installed
psi
Attachment Valve #4 Open TimeDisabled or Not Installed
sec
Attachment Valve #4 Close TimeDisabled or Not Installed
sec
Attachment Valve #4 Tool Flow DirectionDisabled or Not Installed
Description Value Unit
Tool Program Name 0
Maximum Throttle Dial 10
Minimum Throttle Dial Position 1
Underspeed Enable Enabled
Two Pump Flow Combine EnableDisabled or Not Installed
Initial Tool Program Medium Pressure Circuit Main Pump Torque Reduction
Disabled or Not Installed
%
Total Tool Program Medium Pressure Circuit Main Pump Torque Reduction
Disabled or Not Installed
%
One Way/ Two Way Valve ModeDisabled or Not Installed
Variable Relief Valve #1 PressureDisabled or Not Installed
psi
Variable Relief Valve #2 PressureDisabled or Not Installed
psi
F2 Type Valve Max Flow Derate PressureDisabled or Not Installed
psi
F2 Type Valve Flow Derate Start PressureDisabled or Not Installed
psi
F2 Type Valve Flow Derate End PressureDisabled or Not Installed
psi
Multiple Operation Maximum Extend Pilot Pressure for Attachment Valve #1
Disabled or Not Installed
psi
Page 31 of 33
14-Jun-14file://C:\Users\bramurr\Desktop\June Auction\Cat 330DL- P03-2.XML
Multiple Operation Maximum Retract Pilot Pressure for Attachment Valve #1
Disabled or Not Installed
psi
Multiple Operation Maximum Extend Pilot Pres for Combined Attachment Valve
Disabled or Not Installed
psi
Multiple Operation Maximum Retract Pilot Pres for Combined Attachment Valve
Disabled or Not Installed
psi
Hydraulic Temperature High Warning Event Threshold 258.8 Deg F
Attachment Valve #1 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #1 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #1 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #1 Maximum Extend PressureDisabled or Not Installed
psi
Attachment Valve #1 Maximum Retract PressureDisabled or Not Installed
psi
Attachment Valve #1 Open TimeDisabled or Not Installed
sec
Attachment Valve #1 Close TimeDisabled or Not Installed
sec
Attachment Valve #1 Tool Flow DirectionDisabled or Not Installed
Attachment Valve #2 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #2 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #2 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #2 Maximum Extend PressureDisabled or Not Installed
psi
Attachment Valve #2 Maximum Retract PressureDisabled or Not Installed
psi
Attachment Valve #2 Open TimeDisabled or Not Installed
sec
Attachment Valve #2 Close TimeDisabled or Not Installed
sec
Attachment Valve #2 Tool Flow DirectionDisabled or Not Installed
Attachment Valve #3 Flow SettingDisabled or Not Installed
gal/min
Disabled or Not
Page 32 of 33
14-Jun-14file://C:\Users\bramurr\Desktop\June Auction\Cat 330DL- P03-2.XML
Attachment Valve #3 Multi-Oper. Additional Flow Installed gal/min
Valve #3 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #3 Maximum Extend PressureDisabled or Not Installed
psi
Attachment Valve #3 Maximum Retract PressureDisabled or Not Installed
psi
Attachment Valve #3 Open TimeDisabled or Not Installed
sec
Attachment Valve #3 Close TimeDisabled or Not Installed
sec
Attachment Valve #3 Tool Flow DirectionDisabled or Not Installed
Attachment Valve #4 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #4 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #4 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #4 Maximum Extend PressureDisabled or Not Installed
psi
Attachment Valve #4 Maximum Retract PressureDisabled or Not Installed
psi
Attachment Valve #4 Open TimeDisabled or Not Installed
sec
Attachment Valve #4 Close TimeDisabled or Not Installed
sec
Attachment Valve #4 Tool Flow DirectionDisabled or Not Installed
Page 33 of 33
14-Jun-14file://C:\Users\bramurr\Desktop\June Auction\Cat 330DL- P03-2.XML