Caterpillar Electronic Technician 2012A v1.0 Product … Electronic Technician 2012A v1.0 Product...
-
Upload
nguyenkhanh -
Category
Documents
-
view
246 -
download
5
Transcript of Caterpillar Electronic Technician 2012A v1.0 Product … Electronic Technician 2012A v1.0 Product...
Caterpillar Electronic Technician 2012A v1.0 Product Status Report
9/23/2013 2:30 PM
Product Status Report
Monitor
C7 325D (C7C00546)
Logged Diagnostic Codes [Diagnostic Clock = 12537.7411 hours] - C7 325D (C7C00546)
Parameter Value
Product ID GPB00250
Equipment ID GPB00250
Comments
Parameter Value
ECM Serial Number 056J0119AJ
Personality Module Part Number 2705555-00
Parameter Value
Equipment ID GPB00250
Engine Serial Number C7C00546
ECM Part Number 2622879-00
ECM Serial Number 25156649JM
Personality Module Part Number 3327597-00
Personality Module Release Date JUN08
Personality Module Description 325D-HEX-HIHP
Active Event Codes Present Unavailable
Code Description Occ. First Last
1785-10
Intake Manifold Pressure Sensor : Abnormal Rate of Change 4 12532 12534
91- 8Throttle Position Sensor : Abnormal Frequency, Pulse Width, or Period
5 12495 12532
Page 1 of 29
9/23/2013file://C:\Documents and Settings\yard\Desktop\CAT Reports SEPT\Caterpillar 325DL (D0...
Logged Event Codes [Diagnostic Clock = 12537.7414 hours] - C7 325D (C7C00546)
Active Diagnostic Codes - C7 325D (C7C00546)
Active Event Codes - C7 325D (C7C00546)
Current Totals - C7 325D (C7C00546)
Configuration - C7 325D (C7C00546)
Code Description Occ. First Last
E198 (1) Low Fuel Pressure 16 12290 12529
E198 (2) Low Fuel Pressure 1 12447 12447
E390 (1) Fuel Filter Restriction 1 12535 12535
Code Description
1785-10 Intake Manifold Pressure Sensor : Abnormal Rate of Change
Code Description
E390 (1) Fuel Filter Restriction
Description Value Unit
Engine Lifetime Hours Unavailable hours
Total Operating Hours 12538 hours
Total Fuel 67923 gal
Engine Starts 9054
Lifetime Total Engine Revolutions 1209960776 rev
Total Idle Time 2943:57 hours
Total Idle Fuel 3175 gal
Total Max Fuel 132156 gal
Average Load Factor 50 %
Overall Load Factor 51 %
Description Value Unit
Equipment ID GPB00250
Page 2 of 29
9/23/2013file://C:\Documents and Settings\yard\Desktop\CAT Reports SEPT\Caterpillar 325DL (D0...
Injector Trim Calibration - C7 325D (C7C00546)
Machine Control 325D/328D/329D
Engine Serial Number C7C00546
ECM Part Number 2622879-00
ECM Serial Number 25156649JM
Personality Module Part Number 3327597-00
Personality Module Release Date JUN08
Personality Module Description 325D-HEX-HIHP
Rated Power 216 hp at 1800 rpm
Rated Peak Torque 756 lb-ft at 1400 rpm
Test Spec 0K5148 0K6725
Top Engine Speed Range 1980 - 1980 rpm
Ether Solenoid Configuration Not Installed
FLS 31
FTS -3
Security System Immobilizer Installation Status Disabled or Not Installed
Total Tattletale 12
Injector Serial Number File Version Tattletale
Injector1 00000000B310161478F3 0 1
Injector2 000000003B1193803689 0 1
Injector3 000000003B1205584014 0 1
Injector4 000000003B00238357B5 0 2
Injector5 000000003B00238368A7 0 2
Injector6 000000003B120560958D 0 1
Parameter Value
Product ID GPB00250
ECM Part Number 2218874-02
ECM Serial Number 00401190EM
Software Group Part Number 2705467-00
Software Group Release Date NOV2005
Software Group Description 325D HEX CONTROL
Active Diagnostic Codes Present Yes
Page 3 of 29
9/23/2013file://C:\Documents and Settings\yard\Desktop\CAT Reports SEPT\Caterpillar 325DL (D0...
Logged Diagnostic Codes [Diagnostic Clock = 12542 hours] - Machine Control 325D/328D/329D
Logged Event Codes [Diagnostic Clock = 12542 hours] - Machine Control 325D/328D/329D
Active Diagnostic Codes - Machine Control 325D/328D/329D
Current Totals - Machine Control 325D/328D/329D
Code Description Occ. First Last
544- 8Engine Cooling Fan Speed Sensor : Abnormal Frequency, Pulse Width, or Period
186 12306 12539
1657- 3
Left Joystick Thumbwheel : Voltage Above Normal 255 11984 12539
1657- 8
Left Joystick Thumbwheel : Abnormal Frequency, Pulse Width, or Period
255 11984 12539
590- 9 Engine Control Module : Abnormal Update Rate 32 11991 12536
190- 8Engine Speed Sensor : Abnormal Frequency, Pulse Width, or Period
2 12484 12535
2300- 9
Switch Panel : Abnormal Update Rate 4 11988 12199
Code Description Occ. First Last
E043 (2) Low System Voltage Warning 46 10589 12537
Code Description
544- 8 Engine Cooling Fan Speed Sensor : Abnormal Frequency, Pulse Width, or Period
1657- 3 Left Joystick Thumbwheel : Voltage Above Normal
1657- 8 Left Joystick Thumbwheel : Abnormal Frequency, Pulse Width, or Period
Description Value Unit
Total Operating Hours 12543 hours
Engine Maintenance Hours 12540 hours
Engine Oil Hours 3058 hours
Engine Oil Filter Hours 3058 hours
Engine Coolant Hours 3058 hours
Fuel/ Water Separator Hours 0 hours
Fuel Filter Hours 3058 hours
Secondary Fuel Filter Hours Unavailable hours
Page 4 of 29
9/23/2013file://C:\Documents and Settings\yard\Desktop\CAT Reports SEPT\Caterpillar 325DL (D0...
Configuration - Machine Control 325D/328D/329D
Tertiary Fuel Filter Hours Unavailable hours
Fuel Tank Cap Hours Unavailable hours
Hydraulic Pump Hours 12540 hours
Hydraulic Pilot Oil Filter Hours 3058 hours
Hydraulic Case Drain Oil Filter Hours 3058 hours
Return Hydraulic Oil Filter Hours 3058 hours
Attachment Hydraulic Oil Filter Hours 0 hours
Hydraulic Oil Hours 3058 hours
Final Drive Oil Hours 3058 hours
Swing Drive Oil Hours 3058 hours
Travel Motor Hours 1675 hours
Tool #1 Hours 799 hours
Tool #2 Hours 122 hours
Tool #3 Hours 8 hours
Tool #4 Hours 12 hours
Tool #5 Hours 32 hours
Tool #6 Hours 4 hours
Tool #7 Hours 0 hours
Tool #8 Hours 0 hours
Tool #9 Hours 0 hours
Tool #10 Hours 0 hours
Return Hydraulic Oil Filter Bypass Hours 156.1 hours
Return Hydraulic Oil Filter Bypass at Cold Temperature Hours 81.1 hours
Hours of Operation at High Hydraulic Pressure 370.9 hours
Hours of Operation at Relief Hydraulic Pressure 187.7 hours
Description Value Unit
Product ID GPB00250
Hydraulic Power Mode High
Fuel Economy Mode Enable Status Disabled
Economy Mode Disabled or Not Installed
Travel Alarm Installation Status Not Installed
Water Separator Level Switch Configuration Normally Closed (to Ground)
Fuel Filter Differential Pressure Switch Config Not Installed
Secondary Fuel Filter Differential Pressure Switch Config
Not Installed
Page 5 of 29
9/23/2013file://C:\Documents and Settings\yard\Desktop\CAT Reports SEPT\Caterpillar 325DL (D0...
Attachment Hydraulic Oil Filter Switch Configuration Not Installed
Auto Lube Warning Indicator Enable Switch Configuration
Not Installed
Machine Overload Pressure Sensor Installation Installed
Machine Overload Pressure Threshold 2770 psi
Heavy Lift System Installation Status Installed
Engine Fan Type Configuration Viscous Clutch
Engine Cooling Fan MapHigh Ambient Temperature + Low Noise
Engine Fan Reversing Feature Installation Status Disabled or Not Installed
Engine Fan Reverse Operation Time Disabled or Not Installed sec
Machine Application Configuration EAME Multi-Proc
Main Pump Flow Limitation Pres Sol Installation Installed
Attachment Valve #1 Configuration F2 - One Way or Two Way
Attachment Valve #2 Configuration F2 - One Way or Two Way
Attachment Valve #3 ConfigurationAttachment Pump Valve - Two Way
Attachment Valve #4 Configuration Not Installed
Attachment Valve #1 Control Type Configuration Electrical
Attachment Valve #2 Control Type Configuration Electrical
Attachment Valve #3 Control Type Configuration Electrical
Attachment Valve #4 Control Type Configuration Disabled or Not Installed
Attachment Valve #1 Combiner ConfigurationValve #2 Combined with Valve #1
Auxiliary Circuit Flow Combining Solenoid Installation Status
Disabled or Not Installed
Hammer Return to Tank Solenoid Installation Status Installed
Variable Relief Valve Type Configuration Unavailable
Variable Relief Valve #1 ConfigurationInstalled on Valve #1 Extend port
Variable Relief Valve #2 Configuration Not Installed
F2 Type Valve Load Sense Pres Sensor Installation Not Installed
Joystick Handle Configuration Modulation Handle
Foot Switch Installation Status Not Installed
Left Attachment Pedal Installation Status Not Installed
Right Attachment Pedal Installation Status Not Installed
Left Joystick Switch #1 Control Mode No valve controlled
Left Joystick Switch #2 Control Mode No valve controlled
Left Joystick Switch #4 Control Mode Disabled or Not Installed
Page 6 of 29
9/23/2013file://C:\Documents and Settings\yard\Desktop\CAT Reports SEPT\Caterpillar 325DL (D0...
Right Joystick Switch #1 Control Mode Momentary - Valve #1 Extend
Right Joystick Switch #2 Control Mode No valve controlled
Right Joystick Switch #4 Control Mode Disabled or Not Installed
Foot Switch Control Mode Disabled or Not Installed
Left Joystick Thumbwheel Control Mode Attachment Valve #1
Right Joystick Thumbwheel Control Mode Attachment Valve #3
Left Attachment Pedal Control Mode Disabled or Not Installed
Right Attachment Pedal Control Mode Disabled or Not Installed
Travel Speed Shift Low Delay 0.4 sec
Travel Speed Shift High Delay 0.4 sec
Travel Speed Shift Low Pres 2611 psi
Travel Speed Shift High Pressure 4641 psi
One Touch Engine Speed Setting 1020 rpm
AESC Setting 1300 rpm
AESC Delay Time 5.0 sec
Throttle Dial Position 1 Engine Speed 950 rpm
Throttle Dial Position 2 Engine Speed 1020 rpm
Throttle Dial Position 3 Engine Speed 1160 rpm
Throttle Dial Position 4 Engine Speed 1300 rpm
Throttle Dial Position 5 Engine Speed 1470 rpm
Throttle Dial Position 6 Engine Speed 1590 rpm
Throttle Dial Position 7 Engine Speed 1700 rpm
Throttle Dial Position 8 Engine Speed 1800 rpm
Throttle Dial Position 9 Engine Speed 1900 rpm
Throttle Dial Position 10 Engine Speed 1980 rpm
Throttle Dial Position 1 Hydraulic System Torque Percentage
25.0 %
Throttle Dial Position 2 Hydraulic System Torque Percentage
40.0 %
Throttle Dial Position 3 Hydraulic System Torque Percentage
61.0 %
Throttle Dial Position 4 Hydraulic System Torque Percentage
69.0 %
Throttle Dial Position 5 Hydraulic System Torque Percentage
78.0 %
Throttle Dial Position 6 Hydraulic System Torque Percentage
85.0 %
Throttle Dial Position 7 Hydraulic System Torque Percentage
92.0 %
Throttle Dial Position 8 Hydraulic System Torque
Page 7 of 29
9/23/2013file://C:\Documents and Settings\yard\Desktop\CAT Reports SEPT\Caterpillar 325DL (D0...
Percentage 92.0 %
Throttle Dial Position 9 Hydraulic System Torque Percentage
92.0 %
Throttle Dial Position 10 Hydraulic System Torque Percentage
100.0 %
Engine Oil Recommended Maintenance Interval 500 hours
Engine Oil Filter Recommended Maintenance Interval 500 hours
Engine Coolant Recommended Maintenance Interval 3000 hours
Fuel/ Water Separator Recommended Maint Interval 0 hours
Fuel Filter Recommended Maint Interval 500 hours
Secondary Fuel Filter Recommended Maint Interval Unavailable hours
Tertiary Fuel Filter Recommended Maintenance Interval
Unavailable hours
Fuel Tank Cap Recommended Maintenance Interval Unavailable hours
Hydraulic Pilot Oil Filter Recommended Maintenance Interval
1000 hours
Hydraulic Case Drain Oil Filter Recommended MI 1000 hours
Return Hyd Oil Filter Recommended Maint Interval 2000 hours
Attachment Hydraulic Oil Filter Recommended Maintenance Interval
0 hours
Final Drive Oil Recommended Maintenance Interval 2000 hours
Hydraulic Oil Recommended Maintenance Interval 2000 hours
Swing Drive Oil Recommended Maintenance Interval 1000 hours
Advanced Machine Security System Installation Status
Not Installed
Sunday Security System Bypass Start Time Disabled or Not Installed
Sunday Security System Bypass Stop Time Disabled or Not Installed
Monday Security System Bypass Start Time Disabled or Not Installed
Monday Security System Bypass Stop Time Disabled or Not Installed
Tuesday Security System Bypass Start Time Disabled or Not Installed
Tuesday Security System Bypass Stop Time Disabled or Not Installed
Wednesday Security System Bypass Start Time Disabled or Not Installed
Wednesday Security System Bypass Stop Time Disabled or Not Installed
Thursday Security System Bypass Start Time Disabled or Not Installed
Thursday Security System Bypass Stop Time Disabled or Not Installed
Friday Security System Bypass Start Time Disabled or Not Installed
Friday Security System Bypass Stop Time Disabled or Not Installed
Saturday Security System Bypass Start Time Disabled or Not Installed
Saturday Security System Bypass Stop Time Disabled or Not Installed
Page 8 of 29
9/23/2013file://C:\Documents and Settings\yard\Desktop\CAT Reports SEPT\Caterpillar 325DL (D0...
Calibration Status - Machine Control 325D/328D/329D
Tool Configuration - Machine Control 325D/328D/329D
AccuGrade System Installation Status Unavailable
Hydraulic Cab Riser Installation Status Unavailable
Hydraulic Cab Riser Raise Snubbing Angle Gain Unavailable
Hydraulic Cab Riser Raise Snubbing Rate Gain Unavailable
Hydraulic Cab Riser Lower Snubbing Angle Gain Unavailable
Hydraulic Cab Riser Lower Snubbing Rate Gain Unavailable
Calibration Status Last Successful Completion
Attachment Valve #1 Extend Success 1.2 hours
Attachment Valve #1 Retract Success 1.2 hours
Attachment Valve #2 Extend Success 1.2 hours
Attachment Valve #2 Retract Success 1.2 hours
Attachment Valve #3 Extend Failed 0.0 hours
Attachment Valve #3 Retract Failed 0.0 hours
Attachment Valve #4 Extend Failed 0.0 hours
Attachment Valve #4 Retract Failed 0.0 hours
Engine Speed Calibration Success 11986.3 hours
Left Joystick Thumbwheel Calibration Success 0.3 hours
Right Joystick Thumbwheel Calibration Success 7140.2 hours
Left Attachment Pedal Calibration Failed 0.0 hours
Right Attachment Pedal Calibration Failed 0.0 hours
PRV - Pressure Gauge Failed 0.0 hours
PRV - Flow Meter for Two Pump Flow Combined Success 1.3 hours
PRV - Attachment Valve #1 Flow Limit Success 1.3 hours
PRV - Combined Attachment Valve Flow Limit Failed 0.0 hours
PRV - Power Shift Pressure Calibration Success 0.8 hours
Boom Cylinder Extend Pilot Pressure Limit Solenoid Cal
Success Never Successfully Calibrated
Stick Cylinder Retract Pilot Pressure Limit Solenoid Cal
Success Never Successfully Calibrated
PRV - Variable Relief Pressure Calibration Solenoid 1 Failed 0.0 hours
PRV - Variable Relief Pressure Calibration Solenoid 2 Failed 0.0 hours
Page 9 of 29
9/23/2013file://C:\Documents and Settings\yard\Desktop\CAT Reports SEPT\Caterpillar 325DL (D0...
Description Value Unit
Tool Program Name TILTSKUFFE
Maximum Throttle Dial 10
Minimum Throttle Dial Position 1
Underspeed Enable Enabled
Two Pump Flow Combine Enable Disabled
Initial Tool Program Medium Pressure Circuit Main Pump Torque Reduction
5 %
Total Tool Program Medium Pressure Circuit Main Pump Torque Reduction
50 %
One Way/ Two Way Valve Mode Two Way
Variable Relief Valve #1 Pressure 3046 psi
Variable Relief Valve #2 PressureDisabled or Not Installed
psi
F2 Type Valve Max Flow Derate PressureDisabled or Not Installed
psi
F2 Type Valve Flow Derate Start PressureDisabled or Not Installed
psi
F2 Type Valve Flow Derate End PressureDisabled or Not Installed
psi
Multiple Operation Maximum Extend Pilot Pressure for Attachment Valve #1
580 psi
Multiple Operation Maximum Retract Pilot Pressure for Attachment Valve #1
580 psi
Multiple Operation Maximum Extend Pilot Pres for Combined Attachment Valve
580 psi
Multiple Operation Maximum Retract Pilot Pres for Combined Attachment Valve
580 psi
Hydraulic Temperature High Warning Event Threshold 212.0 Deg F
Attachment Valve #1 Flow Setting 16 gal/min
Attachment Valve #1 Multi-Oper. Additional Flow 0 gal/min
Valve #1 Nominal Pressure 2321 psi
Attachment Valve #1 Maximum Extend Pressure 580 psi
Attachment Valve #1 Maximum Retract Pressure 0 psi
Attachment Valve #1 Open Time 0.20 sec
Attachment Valve #1 Close Time 0.20 sec
Attachment Valve #1 Tool Flow Direction Reverse
Attachment Valve #2 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #2 Multi-Oper. Additional FlowDisabled or Not
gal/min
Page 10 of 29
9/23/2013file://C:\Documents and Settings\yard\Desktop\CAT Reports SEPT\Caterpillar 325DL (D0...
Tool Configuration - Machine Control 325D/328D/329D
Installed
Valve #2 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #2 Maximum Extend Pressure 580 psi
Attachment Valve #2 Maximum Retract Pressure 0 psi
Attachment Valve #2 Open Time 0.20 sec
Attachment Valve #2 Close Time 0.20 sec
Attachment Valve #2 Tool Flow Direction Normal
Attachment Valve #3 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #3 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #3 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #3 Maximum Extend Pressure 203 psi
Attachment Valve #3 Maximum Retract Pressure 203 psi
Attachment Valve #3 Open Time 0.20 sec
Attachment Valve #3 Close Time 0.20 sec
Attachment Valve #3 Tool Flow Direction Reverse
Attachment Valve #4 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #4 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #4 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #4 Maximum Extend PressureDisabled or Not Installed
psi
Attachment Valve #4 Maximum Retract PressureDisabled or Not Installed
psi
Attachment Valve #4 Open TimeDisabled or Not Installed
sec
Attachment Valve #4 Close TimeDisabled or Not Installed
sec
Attachment Valve #4 Tool Flow DirectionDisabled or Not Installed
Description Value Unit
Tool Program Name MONTABERT
Page 11 of 29
9/23/2013file://C:\Documents and Settings\yard\Desktop\CAT Reports SEPT\Caterpillar 325DL (D0...
Maximum Throttle Dial 10
Minimum Throttle Dial Position 1
Underspeed Enable Enabled
Two Pump Flow Combine Enable Enabled
Initial Tool Program Medium Pressure Circuit Main Pump Torque Reduction
5 %
Total Tool Program Medium Pressure Circuit Main Pump Torque Reduction
50 %
One Way/ Two Way Valve Mode One Way
Variable Relief Valve #1 Pressure 2756 psi
Variable Relief Valve #2 PressureDisabled or Not Installed
psi
F2 Type Valve Max Flow Derate PressureDisabled or Not Installed
psi
F2 Type Valve Flow Derate Start PressureDisabled or Not Installed
psi
F2 Type Valve Flow Derate End PressureDisabled or Not Installed
psi
Multiple Operation Maximum Extend Pilot Pressure for Attachment Valve #1
580 psi
Multiple Operation Maximum Retract Pilot Pressure for Attachment Valve #1
580 psi
Multiple Operation Maximum Extend Pilot Pres for Combined Attachment Valve
580 psi
Multiple Operation Maximum Retract Pilot Pres for Combined Attachment Valve
580 psi
Hydraulic Temperature High Warning Event Threshold 212.0 Deg F
Attachment Valve #1 Flow Setting 79 gal/min
Attachment Valve #1 Multi-Oper. Additional Flow 0 gal/min
Valve #1 Nominal Pressure 2393 psi
Attachment Valve #1 Maximum Extend Pressure 580 psi
Attachment Valve #1 Maximum Retract PressureDisabled or Not Installed
psi
Attachment Valve #1 Open Time 0.20 sec
Attachment Valve #1 Close Time 0.20 sec
Attachment Valve #1 Tool Flow DirectionDisabled or Not Installed
Attachment Valve #2 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #2 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Page 12 of 29
9/23/2013file://C:\Documents and Settings\yard\Desktop\CAT Reports SEPT\Caterpillar 325DL (D0...
Tool Configuration - Machine Control 325D/328D/329D
Valve #2 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #2 Maximum Extend Pressure 580 psi
Attachment Valve #2 Maximum Retract PressureDisabled or Not Installed
psi
Attachment Valve #2 Open Time 0.20 sec
Attachment Valve #2 Close Time 0.20 sec
Attachment Valve #2 Tool Flow DirectionDisabled or Not Installed
Attachment Valve #3 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #3 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #3 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #3 Maximum Extend Pressure 203 psi
Attachment Valve #3 Maximum Retract Pressure 203 psi
Attachment Valve #3 Open Time 0.20 sec
Attachment Valve #3 Close Time 0.20 sec
Attachment Valve #3 Tool Flow Direction Normal
Attachment Valve #4 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #4 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #4 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #4 Maximum Extend PressureDisabled or Not Installed
psi
Attachment Valve #4 Maximum Retract PressureDisabled or Not Installed
psi
Attachment Valve #4 Open TimeDisabled or Not Installed
sec
Attachment Valve #4 Close TimeDisabled or Not Installed
sec
Attachment Valve #4 Tool Flow DirectionDisabled or Not Installed
Description Value Unit
Page 13 of 29
9/23/2013file://C:\Documents and Settings\yard\Desktop\CAT Reports SEPT\Caterpillar 325DL (D0...
Tool Program Name DNA
Maximum Throttle Dial 10
Minimum Throttle Dial Position 1
Underspeed Enable Enabled
Two Pump Flow Combine Enable Enabled
Initial Tool Program Medium Pressure Circuit Main Pump Torque Reduction
5 %
Total Tool Program Medium Pressure Circuit Main Pump Torque Reduction
50 %
One Way/ Two Way Valve Mode One Way
Variable Relief Valve #1 Pressure 3046 psi
Variable Relief Valve #2 PressureDisabled or Not Installed
psi
F2 Type Valve Max Flow Derate PressureDisabled or Not Installed
psi
F2 Type Valve Flow Derate Start PressureDisabled or Not Installed
psi
F2 Type Valve Flow Derate End PressureDisabled or Not Installed
psi
Multiple Operation Maximum Extend Pilot Pressure for Attachment Valve #1
580 psi
Multiple Operation Maximum Retract Pilot Pressure for Attachment Valve #1
580 psi
Multiple Operation Maximum Extend Pilot Pres for Combined Attachment Valve
580 psi
Multiple Operation Maximum Retract Pilot Pres for Combined Attachment Valve
580 psi
Hydraulic Temperature High Warning Event Threshold 212.0 Deg F
Attachment Valve #1 Flow Setting 55 gal/min
Attachment Valve #1 Multi-Oper. Additional Flow 0 gal/min
Valve #1 Nominal Pressure 2321 psi
Attachment Valve #1 Maximum Extend Pressure 580 psi
Attachment Valve #1 Maximum Retract PressureDisabled or Not Installed
psi
Attachment Valve #1 Open Time 0.20 sec
Attachment Valve #1 Close Time 0.20 sec
Attachment Valve #1 Tool Flow DirectionDisabled or Not Installed
Attachment Valve #2 Flow SettingDisabled or Not Installed
gal/min
Disabled or Not
Page 14 of 29
9/23/2013file://C:\Documents and Settings\yard\Desktop\CAT Reports SEPT\Caterpillar 325DL (D0...
Tool Configuration - Machine Control 325D/328D/329D
Attachment Valve #2 Multi-Oper. Additional Flow Installed gal/min
Valve #2 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #2 Maximum Extend Pressure 580 psi
Attachment Valve #2 Maximum Retract PressureDisabled or Not Installed
psi
Attachment Valve #2 Open Time 0.20 sec
Attachment Valve #2 Close Time 0.20 sec
Attachment Valve #2 Tool Flow DirectionDisabled or Not Installed
Attachment Valve #3 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #3 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #3 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #3 Maximum Extend Pressure 203 psi
Attachment Valve #3 Maximum Retract Pressure 203 psi
Attachment Valve #3 Open Time 0.20 sec
Attachment Valve #3 Close Time 0.20 sec
Attachment Valve #3 Tool Flow Direction Normal
Attachment Valve #4 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #4 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #4 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #4 Maximum Extend PressureDisabled or Not Installed
psi
Attachment Valve #4 Maximum Retract PressureDisabled or Not Installed
psi
Attachment Valve #4 Open TimeDisabled or Not Installed
sec
Attachment Valve #4 Close TimeDisabled or Not Installed
sec
Attachment Valve #4 Tool Flow DirectionDisabled or Not Installed
Page 15 of 29
9/23/2013file://C:\Documents and Settings\yard\Desktop\CAT Reports SEPT\Caterpillar 325DL (D0...
Description Value Unit
Tool Program Name KLO G315
Maximum Throttle Dial 10
Minimum Throttle Dial Position 1
Underspeed Enable Enabled
Two Pump Flow Combine Enable Enabled
Initial Tool Program Medium Pressure Circuit Main Pump Torque Reduction
5 %
Total Tool Program Medium Pressure Circuit Main Pump Torque Reduction
50 %
One Way/ Two Way Valve Mode Two Way
Variable Relief Valve #1 Pressure 5076 psi
Variable Relief Valve #2 PressureDisabled or Not Installed
psi
F2 Type Valve Max Flow Derate PressureDisabled or Not Installed
psi
F2 Type Valve Flow Derate Start PressureDisabled or Not Installed
psi
F2 Type Valve Flow Derate End PressureDisabled or Not Installed
psi
Multiple Operation Maximum Extend Pilot Pressure for Attachment Valve #1
580 psi
Multiple Operation Maximum Retract Pilot Pressure for Attachment Valve #1
580 psi
Multiple Operation Maximum Extend Pilot Pres for Combined Attachment Valve
580 psi
Multiple Operation Maximum Retract Pilot Pres for Combined Attachment Valve
580 psi
Hydraulic Temperature High Warning Event Threshold 212.0 Deg F
Attachment Valve #1 Flow Setting 24 gal/min
Attachment Valve #1 Multi-Oper. Additional Flow 0 gal/min
Valve #1 Nominal Pressure 1160 psi
Attachment Valve #1 Maximum Extend Pressure 580 psi
Attachment Valve #1 Maximum Retract Pressure 580 psi
Attachment Valve #1 Open Time 0.20 sec
Attachment Valve #1 Close Time 0.20 sec
Attachment Valve #1 Tool Flow Direction Normal
Attachment Valve #2 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #2 Multi-Oper. Additional FlowDisabled or Not
gal/min
Page 16 of 29
9/23/2013file://C:\Documents and Settings\yard\Desktop\CAT Reports SEPT\Caterpillar 325DL (D0...
Tool Configuration - Machine Control 325D/328D/329D
Installed
Valve #2 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #2 Maximum Extend Pressure 580 psi
Attachment Valve #2 Maximum Retract Pressure 580 psi
Attachment Valve #2 Open Time 0.20 sec
Attachment Valve #2 Close Time 0.20 sec
Attachment Valve #2 Tool Flow Direction Normal
Attachment Valve #3 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #3 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #3 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #3 Maximum Extend Pressure 203 psi
Attachment Valve #3 Maximum Retract Pressure 203 psi
Attachment Valve #3 Open Time 0.20 sec
Attachment Valve #3 Close Time 0.20 sec
Attachment Valve #3 Tool Flow Direction Normal
Attachment Valve #4 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #4 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #4 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #4 Maximum Extend PressureDisabled or Not Installed
psi
Attachment Valve #4 Maximum Retract PressureDisabled or Not Installed
psi
Attachment Valve #4 Open TimeDisabled or Not Installed
sec
Attachment Valve #4 Close TimeDisabled or Not Installed
sec
Attachment Valve #4 Tool Flow DirectionDisabled or Not Installed
Description Value Unit
Tool Program Name CAT MP20
Page 17 of 29
9/23/2013file://C:\Documents and Settings\yard\Desktop\CAT Reports SEPT\Caterpillar 325DL (D0...
Maximum Throttle Dial 10
Minimum Throttle Dial Position 1
Underspeed Enable Enabled
Two Pump Flow Combine Enable Enabled
Initial Tool Program Medium Pressure Circuit Main Pump Torque Reduction
5 %
Total Tool Program Medium Pressure Circuit Main Pump Torque Reduction
50 %
One Way/ Two Way Valve Mode Two Way
Variable Relief Valve #1 Pressure 5076 psi
Variable Relief Valve #2 PressureDisabled or Not Installed
psi
F2 Type Valve Max Flow Derate PressureDisabled or Not Installed
psi
F2 Type Valve Flow Derate Start PressureDisabled or Not Installed
psi
F2 Type Valve Flow Derate End PressureDisabled or Not Installed
psi
Multiple Operation Maximum Extend Pilot Pressure for Attachment Valve #1
580 psi
Multiple Operation Maximum Retract Pilot Pressure for Attachment Valve #1
580 psi
Multiple Operation Maximum Extend Pilot Pres for Combined Attachment Valve
580 psi
Multiple Operation Maximum Retract Pilot Pres for Combined Attachment Valve
580 psi
Hydraulic Temperature High Warning Event Threshold 212.0 Deg F
Attachment Valve #1 Flow Setting 53 gal/min
Attachment Valve #1 Multi-Oper. Additional Flow 26 gal/min
Valve #1 Nominal Pressure 1450 psi
Attachment Valve #1 Maximum Extend Pressure 580 psi
Attachment Valve #1 Maximum Retract Pressure 580 psi
Attachment Valve #1 Open Time 0.20 sec
Attachment Valve #1 Close Time 0.20 sec
Attachment Valve #1 Tool Flow Direction Normal
Attachment Valve #2 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #2 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #2 Nominal PressureDisabled or Not Installed
psi
Page 18 of 29
9/23/2013file://C:\Documents and Settings\yard\Desktop\CAT Reports SEPT\Caterpillar 325DL (D0...
Tool Configuration - Machine Control 325D/328D/329D
Attachment Valve #2 Maximum Extend Pressure 580 psi
Attachment Valve #2 Maximum Retract Pressure 580 psi
Attachment Valve #2 Open Time 0.20 sec
Attachment Valve #2 Close Time 0.20 sec
Attachment Valve #2 Tool Flow Direction Normal
Attachment Valve #3 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #3 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #3 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #3 Maximum Extend Pressure 203 psi
Attachment Valve #3 Maximum Retract Pressure 203 psi
Attachment Valve #3 Open Time 0.20 sec
Attachment Valve #3 Close Time 0.20 sec
Attachment Valve #3 Tool Flow Direction Normal
Attachment Valve #4 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #4 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #4 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #4 Maximum Extend PressureDisabled or Not Installed
psi
Attachment Valve #4 Maximum Retract PressureDisabled or Not Installed
psi
Attachment Valve #4 Open TimeDisabled or Not Installed
sec
Attachment Valve #4 Close TimeDisabled or Not Installed
sec
Attachment Valve #4 Tool Flow DirectionDisabled or Not Installed
Description Value Unit
Tool Program Name D&A 360V
Maximum Throttle Dial 10
Minimum Throttle Dial Position 1
Underspeed Enable Enabled
Page 19 of 29
9/23/2013file://C:\Documents and Settings\yard\Desktop\CAT Reports SEPT\Caterpillar 325DL (D0...
Two Pump Flow Combine Enable Enabled
Initial Tool Program Medium Pressure Circuit Main Pump Torque Reduction
5 %
Total Tool Program Medium Pressure Circuit Main Pump Torque Reduction
50 %
One Way/ Two Way Valve Mode One Way
Variable Relief Valve #1 Pressure 3191 psi
Variable Relief Valve #2 PressureDisabled or Not Installed
psi
F2 Type Valve Max Flow Derate PressureDisabled or Not Installed
psi
F2 Type Valve Flow Derate Start PressureDisabled or Not Installed
psi
F2 Type Valve Flow Derate End PressureDisabled or Not Installed
psi
Multiple Operation Maximum Extend Pilot Pressure for Attachment Valve #1
580 psi
Multiple Operation Maximum Retract Pilot Pressure for Attachment Valve #1
580 psi
Multiple Operation Maximum Extend Pilot Pres for Combined Attachment Valve
580 psi
Multiple Operation Maximum Retract Pilot Pres for Combined Attachment Valve
580 psi
Hydraulic Temperature High Warning Event Threshold 248.0 Deg F
Attachment Valve #1 Flow Setting 92 gal/min
Attachment Valve #1 Multi-Oper. Additional Flow 0 gal/min
Valve #1 Nominal Pressure 2756 psi
Attachment Valve #1 Maximum Extend Pressure 580 psi
Attachment Valve #1 Maximum Retract PressureDisabled or Not Installed
psi
Attachment Valve #1 Open Time 0.20 sec
Attachment Valve #1 Close Time 0.20 sec
Attachment Valve #1 Tool Flow DirectionDisabled or Not Installed
Attachment Valve #2 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #2 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #2 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #2 Maximum Extend Pressure 580 psi
Page 20 of 29
9/23/2013file://C:\Documents and Settings\yard\Desktop\CAT Reports SEPT\Caterpillar 325DL (D0...
Tool Configuration - Machine Control 325D/328D/329D
Attachment Valve #2 Maximum Retract PressureDisabled or Not Installed
psi
Attachment Valve #2 Open Time 0.20 sec
Attachment Valve #2 Close Time 0.20 sec
Attachment Valve #2 Tool Flow DirectionDisabled or Not Installed
Attachment Valve #3 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #3 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #3 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #3 Maximum Extend Pressure 203 psi
Attachment Valve #3 Maximum Retract Pressure 203 psi
Attachment Valve #3 Open Time 0.20 sec
Attachment Valve #3 Close Time 0.20 sec
Attachment Valve #3 Tool Flow Direction Normal
Attachment Valve #4 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #4 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #4 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #4 Maximum Extend PressureDisabled or Not Installed
psi
Attachment Valve #4 Maximum Retract PressureDisabled or Not Installed
psi
Attachment Valve #4 Open TimeDisabled or Not Installed
sec
Attachment Valve #4 Close TimeDisabled or Not Installed
sec
Attachment Valve #4 Tool Flow DirectionDisabled or Not Installed
Description Value Unit
Tool Program Name NO TOOL 7
Maximum Throttle Dial 10
Minimum Throttle Dial Position 1
Page 21 of 29
9/23/2013file://C:\Documents and Settings\yard\Desktop\CAT Reports SEPT\Caterpillar 325DL (D0...
Underspeed Enable Enabled
Two Pump Flow Combine Enable Disabled
Initial Tool Program Medium Pressure Circuit Main Pump Torque Reduction
5 %
Total Tool Program Medium Pressure Circuit Main Pump Torque Reduction
50 %
One Way/ Two Way Valve Mode Two Way
Variable Relief Valve #1 Pressure 5802 psi
Variable Relief Valve #2 PressureDisabled or Not Installed
psi
F2 Type Valve Max Flow Derate PressureDisabled or Not Installed
psi
F2 Type Valve Flow Derate Start PressureDisabled or Not Installed
psi
F2 Type Valve Flow Derate End PressureDisabled or Not Installed
psi
Multiple Operation Maximum Extend Pilot Pressure for Attachment Valve #1
580 psi
Multiple Operation Maximum Retract Pilot Pressure for Attachment Valve #1
580 psi
Multiple Operation Maximum Extend Pilot Pres for Combined Attachment Valve
580 psi
Multiple Operation Maximum Retract Pilot Pres for Combined Attachment Valve
580 psi
Hydraulic Temperature High Warning Event Threshold 212.0 Deg F
Attachment Valve #1 Flow Setting 32 gal/min
Attachment Valve #1 Multi-Oper. Additional Flow 0 gal/min
Valve #1 Nominal Pressure 1160 psi
Attachment Valve #1 Maximum Extend Pressure 580 psi
Attachment Valve #1 Maximum Retract Pressure 580 psi
Attachment Valve #1 Open Time 0.20 sec
Attachment Valve #1 Close Time 0.20 sec
Attachment Valve #1 Tool Flow Direction Normal
Attachment Valve #2 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #2 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #2 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #2 Maximum Extend Pressure 580 psi
Attachment Valve #2 Maximum Retract Pressure 580 psi
Page 22 of 29
9/23/2013file://C:\Documents and Settings\yard\Desktop\CAT Reports SEPT\Caterpillar 325DL (D0...
Tool Configuration - Machine Control 325D/328D/329D
Attachment Valve #2 Open Time 0.20 sec
Attachment Valve #2 Close Time 0.20 sec
Attachment Valve #2 Tool Flow Direction Normal
Attachment Valve #3 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #3 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #3 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #3 Maximum Extend Pressure 203 psi
Attachment Valve #3 Maximum Retract Pressure 203 psi
Attachment Valve #3 Open Time 0.20 sec
Attachment Valve #3 Close Time 0.20 sec
Attachment Valve #3 Tool Flow Direction Normal
Attachment Valve #4 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #4 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #4 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #4 Maximum Extend PressureDisabled or Not Installed
psi
Attachment Valve #4 Maximum Retract PressureDisabled or Not Installed
psi
Attachment Valve #4 Open TimeDisabled or Not Installed
sec
Attachment Valve #4 Close TimeDisabled or Not Installed
sec
Attachment Valve #4 Tool Flow DirectionDisabled or Not Installed
Description Value Unit
Tool Program Name NO TOOL 8
Maximum Throttle Dial 10
Minimum Throttle Dial Position 1
Underspeed Enable Enabled
Two Pump Flow Combine Enable Disabled
Initial Tool Program Medium Pressure Circuit Main Pump 5 %
Page 23 of 29
9/23/2013file://C:\Documents and Settings\yard\Desktop\CAT Reports SEPT\Caterpillar 325DL (D0...
Torque Reduction
Total Tool Program Medium Pressure Circuit Main Pump Torque Reduction
50 %
One Way/ Two Way Valve Mode Two Way
Variable Relief Valve #1 Pressure 5802 psi
Variable Relief Valve #2 PressureDisabled or Not Installed
psi
F2 Type Valve Max Flow Derate PressureDisabled or Not Installed
psi
F2 Type Valve Flow Derate Start PressureDisabled or Not Installed
psi
F2 Type Valve Flow Derate End PressureDisabled or Not Installed
psi
Multiple Operation Maximum Extend Pilot Pressure for Attachment Valve #1
580 psi
Multiple Operation Maximum Retract Pilot Pressure for Attachment Valve #1
580 psi
Multiple Operation Maximum Extend Pilot Pres for Combined Attachment Valve
580 psi
Multiple Operation Maximum Retract Pilot Pres for Combined Attachment Valve
580 psi
Hydraulic Temperature High Warning Event Threshold 212.0 Deg F
Attachment Valve #1 Flow Setting 13 gal/min
Attachment Valve #1 Multi-Oper. Additional Flow 0 gal/min
Valve #1 Nominal Pressure 1160 psi
Attachment Valve #1 Maximum Extend Pressure 580 psi
Attachment Valve #1 Maximum Retract Pressure 580 psi
Attachment Valve #1 Open Time 0.20 sec
Attachment Valve #1 Close Time 0.20 sec
Attachment Valve #1 Tool Flow Direction Normal
Attachment Valve #2 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #2 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #2 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #2 Maximum Extend Pressure 580 psi
Attachment Valve #2 Maximum Retract Pressure 580 psi
Attachment Valve #2 Open Time 0.20 sec
Attachment Valve #2 Close Time 0.20 sec
Page 24 of 29
9/23/2013file://C:\Documents and Settings\yard\Desktop\CAT Reports SEPT\Caterpillar 325DL (D0...
Tool Configuration - Machine Control 325D/328D/329D
Attachment Valve #2 Tool Flow Direction Normal
Attachment Valve #3 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #3 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #3 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #3 Maximum Extend Pressure 203 psi
Attachment Valve #3 Maximum Retract Pressure 203 psi
Attachment Valve #3 Open Time 0.20 sec
Attachment Valve #3 Close Time 0.20 sec
Attachment Valve #3 Tool Flow Direction Normal
Attachment Valve #4 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #4 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #4 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #4 Maximum Extend PressureDisabled or Not Installed
psi
Attachment Valve #4 Maximum Retract PressureDisabled or Not Installed
psi
Attachment Valve #4 Open TimeDisabled or Not Installed
sec
Attachment Valve #4 Close TimeDisabled or Not Installed
sec
Attachment Valve #4 Tool Flow DirectionDisabled or Not Installed
Description Value Unit
Tool Program Name NO TOOL 9
Maximum Throttle Dial 10
Minimum Throttle Dial Position 1
Underspeed Enable Enabled
Two Pump Flow Combine Enable Disabled
Initial Tool Program Medium Pressure Circuit Main Pump Torque Reduction
5 %
Total Tool Program Medium Pressure Circuit Main Pump Torque 50 %
Page 25 of 29
9/23/2013file://C:\Documents and Settings\yard\Desktop\CAT Reports SEPT\Caterpillar 325DL (D0...
Reduction
One Way/ Two Way Valve Mode Two Way
Variable Relief Valve #1 Pressure 5802 psi
Variable Relief Valve #2 PressureDisabled or Not Installed
psi
F2 Type Valve Max Flow Derate PressureDisabled or Not Installed
psi
F2 Type Valve Flow Derate Start PressureDisabled or Not Installed
psi
F2 Type Valve Flow Derate End PressureDisabled or Not Installed
psi
Multiple Operation Maximum Extend Pilot Pressure for Attachment Valve #1
580 psi
Multiple Operation Maximum Retract Pilot Pressure for Attachment Valve #1
580 psi
Multiple Operation Maximum Extend Pilot Pres for Combined Attachment Valve
580 psi
Multiple Operation Maximum Retract Pilot Pres for Combined Attachment Valve
580 psi
Hydraulic Temperature High Warning Event Threshold 258.8 Deg F
Attachment Valve #1 Flow Setting 0 gal/min
Attachment Valve #1 Multi-Oper. Additional Flow 0 gal/min
Valve #1 Nominal Pressure 5802 psi
Attachment Valve #1 Maximum Extend Pressure 580 psi
Attachment Valve #1 Maximum Retract Pressure 580 psi
Attachment Valve #1 Open Time 0.20 sec
Attachment Valve #1 Close Time 0.20 sec
Attachment Valve #1 Tool Flow Direction Normal
Attachment Valve #2 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #2 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #2 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #2 Maximum Extend Pressure 580 psi
Attachment Valve #2 Maximum Retract Pressure 580 psi
Attachment Valve #2 Open Time 0.20 sec
Attachment Valve #2 Close Time 0.20 sec
Attachment Valve #2 Tool Flow Direction Normal
Attachment Valve #3 Flow SettingDisabled or Not
gal/min
Page 26 of 29
9/23/2013file://C:\Documents and Settings\yard\Desktop\CAT Reports SEPT\Caterpillar 325DL (D0...
Tool Configuration - Machine Control 325D/328D/329D
Installed
Attachment Valve #3 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #3 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #3 Maximum Extend Pressure 203 psi
Attachment Valve #3 Maximum Retract Pressure 203 psi
Attachment Valve #3 Open Time 0.20 sec
Attachment Valve #3 Close Time 0.20 sec
Attachment Valve #3 Tool Flow Direction Normal
Attachment Valve #4 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #4 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #4 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #4 Maximum Extend PressureDisabled or Not Installed
psi
Attachment Valve #4 Maximum Retract PressureDisabled or Not Installed
psi
Attachment Valve #4 Open TimeDisabled or Not Installed
sec
Attachment Valve #4 Close TimeDisabled or Not Installed
sec
Attachment Valve #4 Tool Flow DirectionDisabled or Not Installed
Description Value Unit
Tool Program Name NO TOOL 10
Maximum Throttle Dial 10
Minimum Throttle Dial Position 1
Underspeed Enable Enabled
Two Pump Flow Combine Enable Disabled
Initial Tool Program Medium Pressure Circuit Main Pump Torque Reduction
5 %
Total Tool Program Medium Pressure Circuit Main Pump Torque Reduction
50 %
One Way/ Two Way Valve Mode Two Way
Page 27 of 29
9/23/2013file://C:\Documents and Settings\yard\Desktop\CAT Reports SEPT\Caterpillar 325DL (D0...
Variable Relief Valve #1 Pressure 5802 psi
Variable Relief Valve #2 PressureDisabled or Not Installed
psi
F2 Type Valve Max Flow Derate PressureDisabled or Not Installed
psi
F2 Type Valve Flow Derate Start PressureDisabled or Not Installed
psi
F2 Type Valve Flow Derate End PressureDisabled or Not Installed
psi
Multiple Operation Maximum Extend Pilot Pressure for Attachment Valve #1
580 psi
Multiple Operation Maximum Retract Pilot Pressure for Attachment Valve #1
580 psi
Multiple Operation Maximum Extend Pilot Pres for Combined Attachment Valve
580 psi
Multiple Operation Maximum Retract Pilot Pres for Combined Attachment Valve
580 psi
Hydraulic Temperature High Warning Event Threshold 258.8 Deg F
Attachment Valve #1 Flow Setting 0 gal/min
Attachment Valve #1 Multi-Oper. Additional Flow 0 gal/min
Valve #1 Nominal Pressure 5802 psi
Attachment Valve #1 Maximum Extend Pressure 580 psi
Attachment Valve #1 Maximum Retract Pressure 580 psi
Attachment Valve #1 Open Time 0.20 sec
Attachment Valve #1 Close Time 0.20 sec
Attachment Valve #1 Tool Flow Direction Normal
Attachment Valve #2 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #2 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #2 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #2 Maximum Extend Pressure 580 psi
Attachment Valve #2 Maximum Retract Pressure 580 psi
Attachment Valve #2 Open Time 0.20 sec
Attachment Valve #2 Close Time 0.20 sec
Attachment Valve #2 Tool Flow Direction Normal
Attachment Valve #3 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #3 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Page 28 of 29
9/23/2013file://C:\Documents and Settings\yard\Desktop\CAT Reports SEPT\Caterpillar 325DL (D0...
Valve #3 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #3 Maximum Extend Pressure 203 psi
Attachment Valve #3 Maximum Retract Pressure 203 psi
Attachment Valve #3 Open Time 0.20 sec
Attachment Valve #3 Close Time 0.20 sec
Attachment Valve #3 Tool Flow Direction Normal
Attachment Valve #4 Flow SettingDisabled or Not Installed
gal/min
Attachment Valve #4 Multi-Oper. Additional FlowDisabled or Not Installed
gal/min
Valve #4 Nominal PressureDisabled or Not Installed
psi
Attachment Valve #4 Maximum Extend PressureDisabled or Not Installed
psi
Attachment Valve #4 Maximum Retract PressureDisabled or Not Installed
psi
Attachment Valve #4 Open TimeDisabled or Not Installed
sec
Attachment Valve #4 Close TimeDisabled or Not Installed
sec
Attachment Valve #4 Tool Flow DirectionDisabled or Not Installed
Page 29 of 29
9/23/2013file://C:\Documents and Settings\yard\Desktop\CAT Reports SEPT\Caterpillar 325DL (D0...