CADD 2010 - MWAA

Des

ign

Man

ual

M E T R O P O L I T A N W A S H I N G T O N A I R P O R T S A U T H O R I T Y

2010CADD

CADD Standards, CADD January 2010

CADD -

(This Page Blank)


CADD - Preface

PREFACE

THE DESIGN MANUAL

As part of the ongoing design and construction programs at Ronald Reagan Washington National Airport and Washington Dulles International Airport, the Metropolitan Washington Airports Authority (the Authority), Office of Engineering, has developed and adopted a series of documents that describe the codes, standards, details, products, and practices to be followed by Architect/Engineers (A/Es). These documents apply to all design of construction at all facilities on property owned by the Authority. Facilities constructed or modified on the site occupied by the National Air and Space Museum located at Washington Dulles International Airport are exempt from the requirements of the Authority Design Manual.

The Design Manual has been developed to assist Architects/Engineers (A/Es) in understanding the practices and policies that must be incorporated into each project. The Design Manual contains a number of specific requirements that must be followed on all projects, as described above. These can be either Authority contracted projects, Authority direct-constructed projects, and tenant contracted projects.

APPLICABILITY OF THE DESIGN MANUAL

The requirements for design and construction incorporated into the Design Manual and Supporting Volumes are regulations approved by the Metropolitan Washington Airports Authority Board of Directors and shall be considered contract requirements for all A/Es who are performing services under contract to the Authority. Although A/Es who are under contract to tenants of the Authority may not be working under contract provisions that make compliance with these requirements mandatory, the Authority reserves the right, as Owner of all airport facilities, and land on which tenant buildings are constructed, to reject any design or work that does not comply with the requirements of the Design Manual and its supporting volumes. It is, therefore, required that all A/Es performing work that will be constructed on airport property shall perform services consistent with the Authority policies, standards, procedures, and construction requirements contained in the Design Manual and its supporting volumes. The Design Manual shall be considered equivalent to the building codes. The Design Manual in effect at the 30% Submittal will remain the Design Manual of record up to the 100% Final Submittal.

ORGANIZATION OF THE DESIGN MANUAL

The Design Manual is made up of seven volumes. Basic policies, procedures and standards for both Airports:

• Design Manual Requirements for Ronald Reagan Washington National Airport:

• DCA Vol. 1 - Airport Standards and Signing Guidelines • DCA Vol. 2 - Tenant Design Standards

Requirements for Washington Dulles International Airport: • IAD Vol. 1 - Airport Design Standards and Signing Guidelines • IAD Vol. 2 - Main Terminal/Concourse Z Tenant Design Standards • IAD Vol. 3 - Concourse B Tenant Design Standards


CADD - Preface

Requirements for All Projects:

• CADD - CADD Design Standards [THIS DOCUMENT] The seven volumes are intended to supplement each other and must be used together, as appropriate for each airport, to achieve the desired goals of the Authority.

An electronic version of the Design Manual and Supporting Volumes is available on CD-ROM, which may be obtained by contacting the Authority Office of Engineering. It is also available on the Authority website at www.mwaa.com under “Publications”.

OTHER DOCUMENTS

In addition to the Design Manual, the Authority also requires compliance for design and construction with additional policies, procedures, and standards that are published by other departments. These documents include:

• Construction Safety Manual

• Owner Controlled Wrap-Up Insurance Program Manual

• Building Codes Manual

• Contractors Safety and Security Information (Washington Dulles International Airport)

• Safety Policy, Procedures, and Practices by the Risk Management Department

• MASTERSPEC© Specifications Sections specifically edited for Authority projects (primarily Division 01, but including specific technical specification sections)

• Ronald Reagan Washington National Airport and Washington Dulles International Airport Survey Control Data

“To-Reach” Descriptions (two separate volumes) Note that the “To-Reach” documents for Washington Dulles International Airport are no longer provided on the CD-ROM version of the Design Manual. These documents are available through the Authority. The CD-ROM contains information directing the A/Es to the proper group within the Authority to obtain this document.

http://www.mwaa.com/�


CADD - Preface

ACCEPTABLE STANDARDS

The standards established by the above referenced documents, together with Federal Aviation Administration (FAA), National Fire Protection Agency (NFPA), Virginia Uniform Statewide Building Code (USBC), Construction Specifications Institute (CSI), and other referenced materials establish the minimum level of quality and detail required of all Authority projects. These standards in many instances may exceed those used in non-Authority design and construction projects and are often above those established as “Code Minimums”, “Standards of the Industry”, or “generally accepted practices.”

DESIGN MANUAL REVISIONS

This edition of the Design Manual incorporates the modifications and additions that were developed during the Authority annual review of the previous year’s Design Manual. This review includes an analysis of the existing standards and an evaluation of the suggested revisions.

If you feel that a standard or procedure stipulated in this edition of the Design Manual should be revised, we would like to know. To facilitate this, we have included a Design Manual review form that will place your idea in the appropriate hands. All suggestions received will be reviewed and researched and a written response will be provided.


CADD - Preface

DESIGN MANUAL REVISION FORM

SUGGESTED REVISION TO THE DESIGN MANUAL

Date: Log Number: 11

To: Ms. Diane R. Hirsch, PE Manager of Design Metropolitan Washington Airports Authority Ronald Reagan Washington National Airport Washington, DC 20001

From:

Design Manual Volume & Section:

Design Manual Paragraph:

Design Manual Page:

Background: [Insert background for suggested change(s) here.] 2010 Design Manual Text: [Copy and paste here the text from the 2010 Design Manual for which a revision will be suggested.] Proposed 2011 Design Manual Text: [Use RED text, normal font not bold, to indicate added language. Use “strikeout” to indicate deleted language. Do not use “track changes”.]


CADD - Table of Contents

TABLE OF CONTENTS

PREFACE ................................................................................................................................................................................. 3

TABLE OF CONTENTS............................................................................................................................................................ 7

INTRODUCTION..................................................................................................................................................................... 11

SECTION I: CADD Standards .............................................................................................................................................. 13

CHAPTER 1 Introduction...................................................................................................................................................... 13

1.1 CADD Software Requirements ......................................................................................................................... 13

1.2 Purpose of This Manual .................................................................................................................................... 13

1.3 Project Organization.......................................................................................................................................... 13

CHAPTER 2 General Standards........................................................................................................................................... 15

2.1 Limitations of Cadd Files.................................................................................................................................. 15

2.2 Interchangeable Terminology .......................................................................................................................... 15

2.3 Target Systems.................................................................................................................................................. 16

2.4 Basic Drawing File Standards .......................................................................................................................... 16

2.5 Drawing File Setup ............................................................................................................................................ 19

2.6 Graphic Concepts.............................................................................................................................................. 20

2.7 Level/Layer Assignments ................................................................................................................................. 27

2.8 Compiling CADD features in Model Files........................................................................................................ 29

2.9 Drawing Output.................................................................................................................................................. 29

2.10 Deliverables, Data Exchange and Media Format.......................................................................................... 30

2.11 Submittal Requirements ................................................................................................................................. 31

CHAPTER 3 Drawing File Information................................................................................................................................. 33

3.1 Naming Conventions......................................................................................................................................... 33

3.2 Standard Sheet Formats (Cover Sheet and Title Block Sheet) ..................................................................... 33

3.3 Drawing Preparation/Arrangement .................................................................................................................. 33

3.4 Quality Check (QC) CADD Checklist................................................................................................................ 33

3.5 Addenda Sketches............................................................................................................................................. 33



CHAPTER 4 Model File Level/Layer Assignment Tables................................................................................................... 49

4.1 General ............................................................................................................................................................... 49

4.2 Naming Conventions – Model Files and Level/Layer Tables......................................................................... 49

4.3 Level/Layer Assignment Tables – Model Files ............................................................................................... 52

4.4 Assignment Tables............................................................................................................................................ 54

4.5 Hazardous Materials.......................................................................................................................................... 57

4.6 Civil ..................................................................................................................................................................... 62

4.7 Fueling Systems .............................................................................................................................................. 130

4.8 Landscape........................................................................................................................................................ 134

4.9 Structural Buildings ........................................................................................................................................ 139

4.10 Structural Civil ............................................................................................................................................... 151

4.11 Architectural .................................................................................................................................................. 163

4.12 Interiors .......................................................................................................................................................... 173

4.13 Fire Protection ............................................................................................................................................... 182

4.14 Fire Alarm System ......................................................................................................................................... 189

4.15 Plumbing ........................................................................................................................................................ 193

4.16 Mechanical ..................................................................................................................................................... 198

4.17 Electrical......................................................................................................................................................... 217

4.18 Communications............................................................................................................................................ 233

4.19 Baggage Handling System ........................................................................................................................... 238

4.20 Security & Access Control System.............................................................................................................. 243

4.21 Public Information System ........................................................................................................................... 249

4.22 Aviation Information System........................................................................................................................ 253

4.23 Electronic Monitoring System...................................................................................................................... 256

CHAPTER 5 Sheet File Level/Layer Assignment Tables ................................................................................................. 259

5.1 General ............................................................................................................................................................. 260

5.2 Hazardous Materials........................................................................................................................................ 261

5.3 Survey/Mapping............................................................................................................................................... 262

5.4 Geotechnical .................................................................................................................................................... 263

5.5 Civil ................................................................................................................................................................... 264



5.6 Landscape........................................................................................................................................................ 265

5.7 Structural.......................................................................................................................................................... 266

5.8 Structural Civil ................................................................................................................................................. 267

5.9 Architectural..................................................................................................................................................... 268

5.10 Interiors .......................................................................................................................................................... 269

5.11 Fire Protection ............................................................................................................................................... 270

5.12 Fire Alarm System ......................................................................................................................................... 271

5.13 Plumbing ........................................................................................................................................................ 272

5.14 Mechanical ..................................................................................................................................................... 273

5.15 Electrical......................................................................................................................................................... 274

5.16 Communications............................................................................................................................................ 275

5.17 Baggage Handling System ........................................................................................................................... 276

5.18 Security & Access Control Systems............................................................................................................ 277

5.19 Public Information Systems ......................................................................................................................... 278

5.20 Aviation Information Systems...................................................................................................................... 279

5.21 Electronic Monitoring Systems.................................................................................................................... 280

CHAPTER 6 CADD Symbols............................................................................................................................................... 281

CHAPTER 7 References and Support Files ...................................................................................................................... 283

7.1 Abbreviations................................................................................................................................................... 283

7.2 Basic Electronic Layout Files......................................................................................................................... 283

7.3 References ....................................................................................................................................................... 284

CHAPTER 8 Geographic Information Systems (GIS)Standards and Submittal Requirements ................................... 285

8.1 Applicability: .................................................................................................................................................... 285

8.2 Creating GIS Features from CADD Model Files:........................................................................................... 285

8.3 Structure and Organization of GIS Submittals: ........................................................................................... 285

8.4 Requirements for Ensuring High Quality GIS Deliverables......................................................................... 287

SECTION II: Aerial Photography....................................................................................................................................... 291

CHAPTER 1 Introduction.................................................................................................................................................... 291



LIST OF EXHIBITS............................................................................................................................................................... 313

INDEX ................................................................................................................................................................................... 315


CADD - Introduction

INTRODUCTION

GUIDE TO THIS VOLUME OF THE DESIGN MANUAL

This volume consists of design standards, design criteria, procedures, and products for Ronald Reagan Washington National Airport and Washington Dulles International Airport, and relates to the General CADD Design Standards.

This volume consists of two sections:

Section I CADD Design Standards

Chapter 1: Introduction Chapter 2: General Standards Chapter 3: Drawing File Information Chapter 4: Model File Level/Layer Assignment Tables Chapter 5: Sheet File Level/Layer Assignment Tables Chapter 6: CADD Symbols Chapter 7 References and Support Files Chapter 8 Geographic Information Systems (GIS) Standard Section II Aerial Photography Chapter 1: Introduction


CADD - Introduction

(This Page Blank)


CADD Standards CADD - Section I

SECTION I: CADD Standards

CHAPTER 1 Introduction

This Manual is prepared for use by the Metropolitan Washington Airports Authority (the Authority). The Authority has elected to provide consultants with a resource made available electronically which contains the title sheet, cover sheet, project grid and other support files to assist in creating the design files and to comply with the Authority CADD Standards. These title and cover sheets have been standardized by the Authority and must match the distributed formats in all respects (font style, font weights, line weights, etc.).

The list of CADD support files provided by the Authority to the A/E is given in Paragraph 7.2. Additionally, a “read me” file is also included for instructions on how to properly utilize the support files. This information can be found on the Design Manual CD-ROM in a subdirectory located at… (CD-ROM drive letter):/CAD. You may also obtain this information by contacting the Project Contracting Officer.

Appendix 3, CADD Standards, is currently undergoing substantial revision by the Authority. Designers shall consult with the Authority Design Department before undertaking any design work incorporating CADD for the Authority.

1.1 CADD Software Requirements

1.1.1 General: The Authority permits submittals in either of two formats. For each format, the files must be “native” formats, fully functional, editable, and completely useable within the respective software of creation noted below. It is not acceptable to create drawings on any other software other than noted below and files may not be translated from any other software into these formats. Formats are:

1.1.2 Bentley Microstation: Version 8 or higher preferred; mandatory for civil sitework design.

1.1.3 Autodesk AutoCAD: Version 2004 or higher acceptable for Structural and Building design.

1.2 Purpose of This Manual

1.2.1 General: The purpose of this Manual is to establish uniform standard policies and procedures for the design and drafting work within a CADD environment. The basic engineering and drafting techniques are not discussed.

1.2.2 Policies: The policies established herein are for the information and guidance of Architects/Engineers who perform design services to support the Authority and Authority tenants. Any special condition which may require a variation from these requirements is subject to prior approval by the Authority.

1.2.3 Standards: It is important to note that these standards are not static and will continue to evolve as the Authority requirements and technology change. The basic philosophy of these standards is to:

1.2.3.1 Contract Documents: Create accurate CADD generated Contract Documents.

1.2.3.2 Standardized Drawing Formats: To provide standardized drawing format to assist the owner in maintaining facilities for an extended period of time.

1.2.3.3 Geographic Information System (GIS) Submittals: To define requirements for standardized GIS submittals to the Authority, including required content and format, at appropriate points in during design and construction phase activities.

1.3 Project Organization

1.3.1 Project Structure: This section defines the project directory structure to be used for CADD drawings and various other file types. The primary Project Directory name should contain the following sub-directories:



Project Directory

The Project Directory contains all design files and reference files.

Resource The Resource Directory contains all necessary resource and configuration files subdivided into separate directories as required (e.g., fonts, pen tables plot files).

Doc The Documentation Directory contains the electronic version of all required CADD Documentation (e.g., word documents, spreadsheets).

Spec The Specifications Directory contains the final version of the projects technical specification.

Other The Other Directory contains any miscellaneous files associated with the project (e.g., photos).



CHAPTER 2 General Standards

2.1 Limitations of CADD Files

2.1.1 General: CADD files can contain text, primitive elements (lines, areas, and shapes), or grouped elements (cells, graphic groups, or complex elements). AutoCAD drawing files shall not contain the following elements: Shape symbol fonts, Rtext, OLE frame, Ray, Xline, Proxy objects.

2.2 Interchangeable Terminology

2.2.1 General: Within the various commercially available CADD systems, many identical or related concepts are given different names. To aid users of this Manual, some instances of related or interchangeable terminology used in MicroStation and AutoCAD are listed in Table I-2-1.

TABLE I-2-1 Interchangeable Terminology

MicroStation AutoCAD Definition

Integer d/b 64-bit floating point d/b The method for storing drawing attribute data.

Disk-based Memory-based Where drawing data are stored until the active file is closed.

Auxiliary Coordinate System (ACS) User Coordinate System (UCS)

An XYZ coordinate system where the origin is selected by the user.

Active Current File or object in use.

Cell Block Single or multiple entities grouped together to create a single element.

Dimension attributes Dimensions styles Controls the appearance of dimension elements.

.dgn .dwg A DOS-based extension for drawing files.

Drop Explode Converts an element into multiple entities.

Dynamic update Dragmode/rubberbanding Display of element(s) being drawn or modified as pointer/cursor moves on the screen.

Element Entity A single object contained in a drawing.

Fit Zoom all Displays all graphics currently in the drawing file.

Global origin/design cube World Coordinate System/Origin

Defines the location(s) of all entities in a design/drawing using the Cartesian coordinate system.

Identify/accept Select/pick Entity or entities chosen for manipulation or modification.

Image Slide A screen capture of graphics in raster format.

Key entry field Command prompt Allows for keyboard input from users.

Key point snap Object snap (Osnap) Controls the selection location for entities.

Levels Layers Used as transparent overlays for display graphics.

Line style Linetype Defines the appearance of lines.

Linestring Polyline Connected line segments.

Locate tolerance Pickbox Identification/selection limits for the drawing cursor.

MDL/Visual BASIC ARX/AuoLISP System-specific command language.

Message field Status line Displays current drawing status and/or text output from the application.

Monument point Insertion point Benchmark point used to place objects in a drawing.



TABLE I-2-1 Interchangeable Terminology

MicroStation AutoCAD Definition

Move element Move Relocation of entities.

Patterning Hatching To fill an area within a drawing with a symbolic texture.

Precision key in Coordinate entry User-defined XYZ values.

Reference file External reference A design/drawing file attached to an active drawing.

Seed file Prototype drawing A drawing design template file.

Tentative/Data point Pointing/pick point A point within the drawing selected using a pointing device.

Update Redraw/Regenerate Refreshes screen display.

Model/Sheet Model/Paperspace Type or extent of a drawing file

2.3 Target Systems

2.3.1 General: To ensure successful translations among CADD applications, certain system-specific characteristics were considered and the standard adjusted accordingly. In preparing the standard, several baseline decisions were made:

2.3.1.1 CADD Packages: The standard must be applicable to the latest release of commercially available CADD packages. AutoCAD and MicroStation were chosen based on their prevalence in the industry.

2.3.1.2 CADD Applications: The standard is based on CADD applications that utilize layer/level names and reference files.

2.3.1.3 Electronic Files: The standard required every final plotted drawing sheet to have its own separate electronic drawing file.

2.3.1.4 Three-Dimensional Files: Since three-dimensional files are not compatible with two-dimensional files, it is recommended that all drawings be created as three-dimensional files.

2.4 Basic Drawing File Standards

2.4.1 Drawing/Working Units: The drawing/working units for all civil drawings shall be set in engineering units. All other disciplines shall be set in architectural units. The

required pre-v8 Bentley MicroStation working units for the civil design files are 12:8000 for the Washington National Airport and 10:1000 for the Dulles International Airport. If MicroStation is used for disciplines other than Civil/Site drawings, the working unit of 12:8000 shall be used for both airports.

2.4.2 Global Origin: The global origin of the airport grid file has been set according to Exhibit I-2-1 and Exhibit I-2-2 for each airport, respectively. The user is to key in X, Y locations such that they are equivalent to the true geometric location of the data based on the airport grid. All elements except contours and spot elevations shall be placed on the Z plane of zero. Contours and spot elevations shall be placed on the Z plane representing the elevation.

2.4.3 Grid System: All civil drawings must be created using the Decimal System and the Airport Coordinate System (ACS) which show all measures in decimal feet. All architectural plans using architectural measures shall reference key points to the ACS. Such designs shall reference a minimum of three (3) plan points to the ACS. This standard grid system is outlined in Exhibit I-2-1 and Exhibit I-2-2. The grid systems are detailed within the most recent version of the Ronald Reagan Washington National Airport Survey control network “To-Reach” Descriptions. The description for Ronald Reagan National Airport is included on the Design Manual CD-ROM. The Description for Washington Dulles International Airport can be obtained by contacting the Manager of the Washington Dulles International Airport Engineering Division at 703-572-2885.



IAD Project Grid Exhibit I-2-1



DCA project grid Exhibit I-2-2



2.5 Drawing File Setup

2.5.1 File Accuracy (Units): CADD systems allow the designer to work in “real world” units. The most common units are feet and inches, feet and tenths of feet, meters, and millimeters. MicroStation’s approach to file accuracy allows the user to set the working units (i.e., real world units) as the following:

2.5.1.1 Master Units (MU): Master units (MU) = the largest unit that may be referred to when working in the design file (e.g., feet, meters).

2.5.1.2 Subunits (SU): Subunits (SU) = Subdivisions of master units in the working unit definition (e.g., inches, millimeters).

2.5.1.3 International Feet versus Survey Feet (MicroStation V8)

International Feet: 1 foot = 0.3048000m US Survey Feet: 1 foot = 0.3048006m

A. Looking at this comparison, the difference between the two (0.0000006 m) may seem insignificant; however, ultimately this difference may cause coordinate values to be off by several feet, resulting in inaccurate design files.

B. By default, a “foot” in MicroStation actually refers to an International Foot. However, the coordinate system upon which all MWAA design work is based is measured in US Survey Feet. MicroStation version 8 continues to utilize working units, which have been expanded to define the unit of measure (Meters, US Survey Feet, or International Feet).

C. The Authority has chosen to utilize this feature in MicroStation to improve the accuracy in which all MWAA design work is created.

D. While this is an important operational improvement, it has significant consequences. Therefore, care must

be exercised to ensure and maintain the integrity of MicroStation DGN files with respect to the units of measure. In MicroStation v8, a workspace is accompanied by a custom units definition file (units. def), which defines the units of measure. To enable, scroll down the units.def file to the section English units (based on U.S. Survey Foot) and delete the # in front of #sf,ft, which will allow for the selection of Survey Feet from the Working Units box the next time MicroStation is started.

2.5.1.4 Cartesian Coordinates: In AutoCAD, the basic drawing unit for any file is the distance between two fixed Cartesian coordinates. For example, the distance between coordinates (1,1,1) and (1,1,2) is one drawing unit. A drawing unit can correspond to any measurement (e.g., inch, foot, meter, and mile). AutoCAD users may enter the “Units” display option to set the desired drawing units.

2.5.2 Origin: Positioned within every electronic drawing file is an origin (“global origin” in MicroStation and “origin” in AutoCAD). The origin of a drawing file is important because it serves as the point of reference from which all other elements are located. Origins are typically defined (located) in a drawing file by the Cartesian coordinate system of x, y, and z. The benefit of standardizing the location of the origin of a drawing is most notable in the use of reference files. Also, in certain disciplines, particularly mapping, the location of the origin determines the available drawing area (MicroStation only). A standardized origin is also helpful when translating files between CADD applications. The global origin for IAD CADD file shall be set to 0,0,0. The global origin for DCA shall be set at 875000, 475000, and 2239.62.

2.5.3 Model Files and Sheet Files: Two distinct types of CADD files are addressed in this standard, model files and sheet files. A model file contains the physical components of a building (e.g., columns, walls, windows, ductwork, piping, etc.). Model files are drawn at full scale and typically represent plans, elevations, section, etc. A sheet file is synonymous with a plotted CADD drawing file. A sheet file is a selected view or portion of the model file(s) within a



border sheet. Sheet files are usually plotted at a particular scale, since the border sheet is scaled up to fit around the full scale model files. In other words, a sheet file is a “ready-to-plot” CADD file. A sheet file is the combination of referenced model files with sheet-specific text/symbols to create a final “ready-to-plot” CADD file.

2.6 Graphic Concepts

2.6.1 Presentation Graphics: The first step in establishing an effective CADD standard is the development of a uniform approach to presentation graphics. Presentation graphics typically consist of drawing elements such as lines, arcs, shapes, text, and their attributes (line color, line width, and line style). This Manual

presents brief overviews of the characteristics of presentation graphics and the philosophy used to standardize them.

2.6.2 Line Widths: Although “monotone” line work is not contractually improper, varied line widths substantially improve readability. Most commercial CADD systems provide an extensive variety of line widths. However, for the majority of drawings, the five line widths defined in Table I-2-2, with the optional 1.00 mils, 1.40 mils, and 2.00 mils lines, are considered sufficient and shall not be expanded unless an appreciable improvement in drawing clarity or contrast can be realized. The following are typical usages for the line widths shown in Table I-2-2:

TABLE I-2-2 Line Widths

Line Thickness mm in. MicroStation LineWeight Line Weight Example

Fine 0.18 0.007 wt = 0

Thin 0.25 0.010 wt = 1

Medium 0.35 0.014 wt = 2

Wide 0.50 0.020 wt = 3

Extra Wide 0.70 0.028 wt = 5

XX Wide 1.00 0.040 wt = 7

XXX Wide 1.40 0.055 wt = 10

XXXX Wide 2.00 0.079 wt = 15

A. Fine (0.18 mils): Fine lines shall be used sparingly, mostly for poche/patterning (this line thickness typically does not reproduce well in blue-line format and/or in photocopies).

B. Thin (0.25 mils): Thin lines shall be used for depicting dimension lines, dimension leader/witness lines, note leader line, line terminators (arrowheads, dots, slashes), phantom lines, hidden lines, center lines, long break lines, schedule grid lines, and object lines seen at a distance.

C. Medium (0.35 mils): Medium lines shall be used for depicting minor object lines, dimension text, text for notes/callouts, and schedule text.

D. Wide (0.50 mils): Wide lines shall be used for major object lines, cut lines, section cutting plane lines, and titles.

E. Extra Wide (0.70 mils): Extra wide lines shall be used for minor title underlining schedule outlines, large titles, and object lines requiring special emphasis. For every large scale details drawn at 3 inches = 1 foot, 0 inches or larger, the extra wide width shall be used for the object lines. Extra wide widths are also appropriate



for use as an elevation grade line, building footprint, or top of grade lines on section/foundation details.

F. XX Wide (1.00 mm): This line weight shall be used for major title underlining and separating portions of drawings.

G. XXX Wide (1.40 mm): This line weight shall be used for border sheet outlines and cover sheet line work and as an option for the designer as required.

H. XXXX Wide (2.00 mm): This line weight shall be used for border sheet outlines and cover sheet line work as an option for the designer as required. The predominant line types/style used in this standard are listed in Table 1-2-3.

TABLE I-2-3 Standard Line Types Styles

ID Description MicroStaton Designator

AutoCAD Designator Example

0 Continuous 0 Continuous

1 Dotted 1 Dot

2 Dashed 2 Hidden

3 Dashed spaced 3 Dashed

6 Dashed double-dotted 6 Divide2

7 Chain 7 Center

2.6.3 Line Color: The primary reason to use color in CADD drawings is to improve the clarity of the drawing on a computer monitor. The variety of colors available in a CADD application depends on the capabilities of the computer monitor and its video card. Today, most systems are capable of displaying from 16 to 256 colors. Based on the limitations of monitor color display capabilities and differing CADD system plotting methods, this Manual recommends that all drawings be created using the basic colors presented in Table I-2-4 whenever possible.



TABLE I-2-4 Screen Color Comparison

Color Number Ratios of RGB, % Color

AutoCAD MicroStation Red Green Blue

Blue 5 1 0 0 255

Gray 8 9 128 128 128

Green 3 2 0 255 0

Red 1 3 255 0 0

Yellow 2 4 255 255 0

Magenta 6 5 255 0 255

Cyan 4 7 0 255 255

White 7 0 255 255 255

Note: Color numbers for AutoCAD and MicroStation were taken from default color tables.

Note: The recommended colors are best viewed on a monitor with a black background.

2.6.4 Screening:

Varying the intensity of gray scales allows users to distinguish different aspects of a drawing when it is plotted. For example, an area on a site designated for demolition can be assigned a color that has been assigned a screening percentage. Existing features shall be shown screened back. When plotted, the area will be shown at a lighter shade compared with other elements in the drawing. This will allow the contractor to immediately identify the demolition area on the drawing. Table I-2-5 lists colors

recommended to be used for screening along with a recommended screening percentage. Using Table I-2-5, MicroStation users can edit a plotter driver, using a text editor, to assign a screening percentage to the specific colors (refer to the MicroStation user’s manuals for information on working with plotter/printer drivers). AutoCAD users must specify requirements for screening according to the output device used. Due to the number of output devices AutoCAD supports, users shall consult the help documentation provided within AutoCAD for information on assigning recommended screening percentages.

TABLE 1-2-5 Screened Colors

AutoCAD MicroStation Ratios of RGB, %

Color Number Screen percent Color Number Screen percent Red Green Blue 250 60 8 60 102 102 102

251 50 200 50 128 128 128

252 40 168 40 153 153 153

253 30 120 30 179 179 179

254 20 56 20 204 204 204



2.6.5 Text Styles/Fonts:

Contrasting text styles (or fonts) are used within a drawing to delineate types of information. In most drawings, these five fonts should be sufficient.

1) Monotext Font: This font creates text characters that are evenly spaced. Monotext font shall be used where text fields need to be aligned such as in schedules or, in some cases, title blocks. Use Monospace 821 BT True Type font.

2) Proportional Font: This font creates text where the characters are proportionally spaced. It is appropriate for general notes, labels, or title blocks. Use Arial True Type font.

3) Slanted Font: A slanted font is used where text needs to be easily distinguished from other text. Use Arial True Type font with the Slant Angle set to 15 deg to achieve the American Standard slope of 2 in 5 (68.2 deg).

4) Filled Font: Filled fonts are used primarily for titles and on cover sheets. Use Ariblk (Arial Black) True Type font.

5) Outline Font: When a pen plotter is used for final output, the outline font is used as a substitute for filled fonts for major titles such as cover sheet information to save plotting time. Use Swissko (Swiss 721 Black Outline) True Type font.

6) NOTE: The fonts for the cover sheets and border sheets in the CADD support files provided by the Authority shall not be changed or modified.

2.6.6 Text Height: Minimum lettering height shall be ⅛" on all drawings.

2.6.6.1 Table I-2-6 is provided for general information regarding text size and its correlation to drawing scale. Text should be clear, organized and legible at half-size plot.

TABLE I-2-6 Inch-pound Text Sizes and Line Type Scales

Scale Text Sizes Line Type Scale

Drawing Scale = 1" = 2000' - 0" 250’ 24000

Drawing Scale = 1" = 1000' - 0" 125’ 12000

Drawing Scale = 1" = 500' - 0" 62.5’ 6000

Drawing Scale = 1" = 400' - 0" 50’ 4800

Drawing Scale = 1" = 200' - 0" 25’ 2400

Drawing Scale = 1" = 100' - 0" 12.5’ 1200

Drawing Scale = 1" = 60' - 0" 7.5’ 720

Drawing Scale = 1" = 50' - 0" 6.25’ 600

Drawing Scale = 1" = 40' - 0" 5’ 480

Drawing Scale = 1" = 30' - 0" 3.75’ 360

Drawing Scale = 1" = 20' - 0" 2.5’ 240

Drawing Scale = 1" = 10' - 0" 1.25’ 120

Drawing Scale = 1" = 5' - 0" 7.5” 60

Drawing Scale = 12” = 1’ – 0” or FULL SIZE 0.125” 1

Drawing Scale = 6" = 1' - 0" 0.25” 2



TABLE I-2-6 Inch-pound Text Sizes and Line Type Scales

Scale Text Sizes Line Type Scale

Drawing Scale = 3" = 1' - 0" 0.50” 4

Drawing Scale = 1-1/2" = 1' - 0" 1” 8

Drawing Scale = 1" = 1' - 0" 1.5” 12

Drawing Scale = 3/4" = 1' - 0" 2” 16

Drawing Scale = 1/2" = 1' - 0" 3” 24

Drawing Scale = 3/8" = 1' - 0" 4” 32

Drawing Scale = 1/4" = 1' - 0" 6” 48

Drawing Scale = 3/16" = 1' - 0" 8” 64

Drawing Scale = 1/8" = 1' - 0" 12” 96

Drawing Scale = 3/32" = 1' - 0" 16” 128

Drawing Scale = 1/16" = 1' - 0" 24” 192

Drawing Scale = 1/32" = 1' - 0" 48” 384

2.6.7 Drawing Orientation and North Arrow

2.6.7.1 The orientation of all plans should be positioned so that the sides of buildings or pavement edges are aligned with sheet edges, in most cases. The most common orientation is one where the north arrow points to the top or to the left of the drawing block.



2.6.7.2 The display of information in the drawing should be consistent in orientation throughout the drawing set. See figure below.



2.6.8 Text Orientation:

2.6.8.1 Line Spacing: Line spacing will be ½ of the text height.

2.6.8.2 Leader Lines: Leader lines shall be line strings with an arrow terminator. Leader lines that terminate to the left should start at the center of the first line of text. Leader lines that terminate to the right should start at the center of the last line of text.

2.6.8.3 Terminators: The approved line terminator for notes on all construction documents is the standard filled terminator in the dimension settings. The size of the filled terminators is a width of .5 and length of 1.5 x the height.



2.6.9 Dimension Terminators: The approved line terminator for dimensions on all construction documents is the standard filled terminator in the dimension settings. The size of the filled terminators is a width of .5 and length of 1.5 x the text height.

2.6.10 Abbreviations: Abbreviations used shall conform to the United States National CAD Standard CSI Uniform Drawing System Module 5, "Terms and Abbreviations." Unusual or uncommon abbreviations required on drawings, not specified by the National Standard, shall be clearly noted and defined on the G series of drawings.

2.7 Level/Layer Assignments

2.7.1 Levels/Layers: CADD levels or layers are analogous to overlays in manual drafting systems and serve to separate graphic elements (lines, shapes, and text) according to the design discipline they represent. The types of information represented by individual levels/layers can be grouped into two (2) primary types: model-specific information and sheet-specific information. Model-specific information represents the physical form of a site, a building, or objects composing a building. This information is often shared between drawings. Examples include walls, doors, light fixtures, and room numbers. Model-specific information may be either literal (e.g., walls) or symbolic (e.g., electrical outlets). Sheet-specific information may include notes, annotative symbols, and titles. This type of information is usually not shared between drawings. To use and manipulate model-specific and sheet-specific information effectively, every level/layer must be defined (standardized) by its name and its use.

2.7.2 Level/Layer Naming Convention: The reuse, not duplication, of graphic information reduces drawing time and improves project coordination. The level/layer is the basic tool used in CADD for managing graphic information. Level/layer names consist of a two-character Discipline Designator (e.g., “AR-” for Architectural, “ME-” for Mechanical), followed by a four-character Major Group (e.g., “DOOR” for Doors, “LITE” for Lighting Fixtures), and followed by a four-character Minor Group (e.g.,

AR-WALL-FULL-EXTR for exterior full height walls versus AR-WALL-FULL-INTR for interior full height walls).

2.7.3 Model Files: Model files represent full-size drawings of building elements, systems, or information (e.g., the mechanical HVAC system, the architectural floor plan, details, and sections) and sheet files represent final plotted sheets. Model files are used as components in creating plotted sheet files. The information contained within a model file for a discipline may be referenced by other disciplines to create the particular model files or sheet files for that discipline. A model file can be considered a “work in progress.” For instance, a mechanical engineer may reference the architect’s floor plan model file to begin development of the HVAC ductwork layout model file. Meanwhile, the architect can continue developing the floor plan to meet new requirements. Any changes to the floor plan would be immediately accessible to the mechanical engineer. The viewing of real-time updates eliminates a great deal of frustration for other disciplines because it allows for on-the-spot rather than after-the-fact modifications.

2.7.4 Level/Layer Assignment Tables - Model Files: The level/layer assignment tables in Section 4.1 present the following:

2.7.4.1 Level/Layer Names: The level/layer names assigned to each model file.

2.7.4.2 Description: A detailed description for each level/layer.

2.7.4.3 Presentation Graphics: The presentation graphics associated with each level/layer. This includes the line style, line width, and color.

2.7.4.4 Annotation Levels/Layers: Users should note that the first eight level/layers for every model file type (with the exception of detail model file types) are the same, the only difference being that the Discipline Designator changes depending on the discipline for that model file type. The unique function of these eight annotation



levels/layers is to contain model-specific information that might not be required by other disciplines. These levels/layers are as follows with ** representing a Discipline Designator (e.g., AR-, CV-):

**ANNO-DIMS Witness/extension lines, dimension terminators and dimension text. **ANNO-KEYN Reference keynotes with associated leaders. **ANNO-NOTE General notes and remarks. **ANNO-NPLT Non-plotting graphic information. **ANNO-PATT Miscellaneous patterning and hatching. **ANNO-SYMB Miscellaneous symbols. **ANNO-TEXT Miscellaneous text and callouts with associated leaders. **ANNO-REFR An AutoCAD user-specific layer for use in attachment of external references (i.e., reference files). 2.7.4.5 Demolition Levels/Layers: Users should note that several model files have three levels/layers reserved for demolition items. These levels/layers are as follows with ** representing a Discipline Designator (e.g., AR-, CV-):

**STAT-DEMO-PHS1 Demolition - phase 1. **STAT-DEMO-PHS2 Demolition - phase 2. **STAT-DEMO-PHS3

Demolition - phase 3. These levels/layers should only be used when an Existing/Demolition model file is being created. For instance, the architect or engineer will sometimes have existing as-built model files, such as Site Plans and Floor Plans from a previous project. A copy of the as-built file will be made for use in the current project. This copy is renamed to be the Existing/Demolition Plan model file for that discipline. In order to distinguish items to be demolished from existing items that will remain, those items should be moved to the Demolition levels/layers (if the demolition is not phased, all items should be moved to the **STAT-DEMO-PHS1 level/layer). When the Existing/Demolition Plan model file is referenced into a new file to create the New construction items, the Demolition levels/layers would be turned off.

2.7.5 Border Sheets: A model file contains information that can be referenced by other disciplines to create other model files or final sheet files. A border sheet model file contains border sheet linework, the title block, and project-specific symbols and text. Typically, each discipline will use the same border sheet and fill in sheet-specific information within the title block or revision block prior to printing the final sheet (e.g., sheet number, designer names).

2.7.6 Reference Files: The use of reference files is a key component in the successful use of the level/layer assignments. To create either a model file or a final sheet file, multiple referenced model files may be required.

2.7.7 Sheet Files: Sheet files are the final project sheets that are ready to be plotted. A sheet file is an assembly of referenced model files plus additional sheet-specific information (e.g., north arrows, scales, section cuts, title block information). Referenced model files are used in the construction of sheet files. The user opens the sheet file type that is appropriate to his/her discipline then references existing model files. The user then “turns on/off” levels/layers within each referenced model file to achieve the desired sheet file. The user then fills in the specific sheet/border information. Once the final sheet file is



achieved, the resulting file is saved (with all reference files attached). Note: All sheet file backfround color shall be set to "black".

2.7.8 Level/Layer Assignment Tables - Sheet Files: The level/layer assignment tables in Section 5.1 present the following:

2.7.8.1 Level/Layer Names: The level/layer names assigned to each sheet file.

2.7.8.2 Description: A detailed description for each level/layer.

2.7.8.3 Presentation Graphics: The presentation graphics associated with each level/layer. This includes the line style, line width, and color.

2.7.8.4 Users should note that the first ten level/layers of the sheet file type for every discipline are the same, with the exception that the Discipline Designator changes depending on the discipline for that sheet file type. The unique function of these ten Annotation levels/layers is to contain sheet-specific information. These levels/layers are as follows with ** representing a Discipline Designator (e.g., AR-, CV-):

**ANNO-DIMS Sheet-specific witness/extension lines, dimension terminators, and dimension text. **ANNO-KEYN Sheet-specific keynotes with associated leaders. **ANNO-LEGN Legends and schedules. **ANNO-NOTE Sheet-specific general notes and remarks. **ANNO-PATT Sheet-specific patterning and hatching (e.g., key plan patterning).

**ANNO-REDL Redlines, markups. **ANNO-REVS Revisions, amendments, addenda, and modifications.

**ANNO-SYMB Sheet-specific symbols (e.g., north arrow, scales). **ANNO-TEXT Sheet-specific text and callouts with associated leaders. **ANNO-REFR An AutoCAD user-specific layer for use in attachment of external references (i.e., reference files).

2.8 Compiling CADD features in Model Files

2.8.1 CADD Manual, Section I, paragraph 8.4 provides a set of required practices A/Es and contractors must follow when compiling features in CADD model files to facilitate GIS integration and to prepare GIS submittals, as described further in Chapter 8. A/Es are required to adhere to the guidance in Section 8.4, including guidance on use of complex versus simple geometry types, topological integrity, rules for compiling line and area/polygon features, use of custom and continuous linestyles, rules for block and cell insertion points and guidelines for snapping blocks and cells to lines and line endpoints.

2.9 Drawing Output

2.9.1 The final plot size for drawings shall be established according to the Design Manual; refer to the Authority Design Manual, Section II, Paragraph 2.7.4.

2.9.2 All plotted drawings shall bear the file name, date and time of the plot within cutline limits.

2.9.3 A drawing log shall be kept to track the file name of all design files created. This log shall contain a detailed description of each file structure; including reference file names, model/base file names, pen tables, and any additional support files which are required to produce a



finished plot of the drawing. This shall be an MS Excel file which is kept in the project directory and archived with the design files when the electronic data is delivered to the Authority.

2.10 Deliverables, Data Exchange and Media Format

2.10.1 Plots of all drawings shall be provided in accordance with the Design Manual Section II, Paragraph 2.7.

2.10.2 Interim drawing submittals shall be as outlined within the Design Manual Section II, Paragraph 2.5, and the Statement of Work.

2.10.3 Delivery Media: All CADD files shall be furnished via compact disc-read only memory (CD-ROM) or DVD, and not on multiple diskettes.

2.10.4 Format: All digital files shall be delivered in a format that is directly readable and compatible with the installation’s CADD software and platforms without conversion. Before a file is placed on the delivery digital media, the following procedures shall be performed:

2.10.4.1 Extraneous Graphics: Remove all extraneous graphics outside the border area, and set the active parameters to a standard setting or those in the seed/prototype file.

2.10.4.2 Directory Specifications: Ensure all reference (external reference) files are attached without device of directory specifications.

2.10.4.3 Compression: Compress and reduce all files using the appropriate utilities.

2.10.4.4 Files: Include all files, both graphic and nongraphic, required for the project (e.g., color tables, pen tables, font libraries, cell/block libraries, user command files, plot files, etc.).

2.10.4.5 Support Files: Ensure that all support files are in the same directory and that references to those files do not include device or directory specifications.

2.10.4.6 Standard Sheets: Include any standard sheets (i.e., abbreviation sheets, standard symbol sheets, etc.) necessary for a complete project.

2.10.5 Documentation: Complete documentation (e.g., data input procedures), pen settings, lock settings, reference files, cells, level assignments, and history (e.g., when developed/modified) information for each file shall be included on level/layer **-ANNO-NPLT (** represents the design discipline). Documentation of the plot for each drawing is needed to duplicate the plot at a later date and shall be provided with the deliverables.

2.10.6 Consultants must label all compact disks with the following information:

Project Title Consultant Name and Contract Number Airport and Project Name Submittal Date Submittal Level Sequence number (for multiple CD’s) A short description of the contents Contact Phone Number and Name Tenant Name (if Applicable)

2.10.6.1 In addition, the following information shall accompany the media:

A. Transmittal sheet

B. QC CADD Sheet

C. MS Excel Spreadsheet listing file names and file descriptions



2.11 Submittal Requirements

2.11.1 General: Consultants shall submit drawings in compliance with the Authority CADD Standard with each required submittal. At 100% submittal level, all CADD drawings shall be submitted to include model files, sheet files, reference files and any other files required by Paragraph 2.9.



(This Page Blank)



CHAPTER 3 Drawing File Information

3.1 Naming Conventions

3.1.1 Model File Naming: Model files shall be named in accordance with the naming convention outlined in the applicable chapter exhibits.

3.1.2 Sheet File Naming: Sheet files shall be named in accordance with the naming convention outlined in chapter exhibits. In assigning a sheet number, the sheet number shall coordinate with the same name assigned to the electronic sheet file.

3.2 Standard Sheet Formats (Cover Sheet and Title Block Sheet)

3.2.1 General: The standard format of Cover Sheets and Title Block Sheets are shown in the applicable chapter exhibits. The Authority will provide files of the cover sheets and title block sheets in native electronic format for Bentley MicroStation and AutoDesk AutoCAD.

3.3 Drawing Preparation/Arrangement

3.3.1 General: The title block sheets and cover sheets shall be referenced into the CADD file. They shall not be placed as a separate cell or block. The use of reference files in the file set-up is required to ensure file integrity. The use of reference files eliminates the need for duplication of data reducing the problems encountered when updating drawings. Sheet drawings shall be arranged in sequence as defined in Table I-3-1.

3.3.2 Reference Files: In order to avoid conflicting attachments of reference files, there shall be no duplicate file names within the project directory structure or copies of the same file within the project directory structure.

3.4 Quality Check (QC) CADD Checklist

3.4.1 General: The QC CADD checklist is shown on page 45. This checklist is used as a means of validating the CADD files submitted have been quality inspected. An “X” in the appropriate YES or NO field, with a signature, indicates this item is in conformance with the items outlined in the Design Manual Appendix 3 CADD Standards. This QC CADD checklist shall be accompanied with each submittal and may be submitted as a hard copy or electronic file. The QC CADD Checklist is available on the CD-ROM located in the CAD directory.

3.5 Addenda Sketches

3.5.1 Sketch Format: The standard format of 8 ½" x 11" or 11" x 17" sketches are shown in chapter exhibits. The Authority will provide files of the sketch formats in native electronic format for Bentley MicroStation and AutoDesk AutoCAD. It is the obligation of each designer to ensure that all submittals match the hard-copy line work and graphics exactly as shown. Any deviation will be rejected.

3.5.2 File Naming Conventions for Addenda or Sketches: Model files and all drawing sheet files shall be named in accordance with the Name designation convention outlined in the applicable chapter exhibits. In assigning a sheet number, the sheet number shall coordinate with the same name assigned to the electronic sheet file.



Model File Naming Convention Exhibit I-3-1



Sheet File Naming Convention Exhibit I-3-2



Addendum File Naming Convention Exhibit I-3-3



Authority Standard Drawing Sheet Titleblock For IAD Exhibit I-3-4



Authority Standard Cover Sheet For IAD Exhibit I-3-5



Authority Enlarged Plan Sheet For IAD Exhibit I-3-6



Authority Standard Drawing Sheet Titleblock For DCA Exhibit I-3-7



Authority Standard Cover Sheet For DCA Exhibit I-3-8



Authority Standard Addenda or Sketches Sheet Exhibit I-3-9



PROJECT IDENTIFIER

PROJECT

DATE

ITEMS YES NO

1. Are the base/model files provided?

2. Is the base file correctly located within the Airport Coordinate System (ACS)?

3. Are sheet numbers and drawing numbers indicated, as well as correctly shown?

4. Are the files drawn to scale and measurements correct?

5. Is text displayed correctly?

6. Is the proper documentation and support files provided?

7. Are the CADD files saved as 3D files?

8. Are the title and standard title block sheet formats to Authority standards?

9. Are the appropriate leveling schemes being used as outlined in the CADD Standard?

10. Is the CADD file identical in appearance to the hard copy?

11. Is the CD-ROM labeled correctly?

12. Are the file naming conventions in accordance for the model and sheet files?

13. Are all CADD files and disciplines present as outlined in the Drawing Index, including reference files?

14. Is the information contained inside the drawing border the only information in the file?

15. Does one CADD file contain only one drawing?

Have 30%-60%-90%-100% (circle one) Submission CADD files been submitted in acceptable format per the Design Manual? Yes No



TABLE I-3-1

Discipline/Subject Numbering Breakdown and Drawing Set Organization (For Reference Only) *Note: No changes are permitted in the series numbering; however, additions (i.e., GN5, GN6 or CN11, CN12 etc.) may be proposed by A/Es for consideration by the Authority

General: GN00.series Cover Sheet GN01.series Drawing Index GN02.series Plot/Vicinity Locations, Haul Routes, Contractor Staging Area GN03.series Construction Phasing Plans, Maintenance of Traffic GN04.series Building Code Analysis and Egress Analysis Hazardous Materials: HM00.series General Notes, Abbreviations, and Symbols HM01.series Site Plan HM02 series Petroleum Contaminated Soil, Gravel & Water from Demolition Activities HM03.series Petroleum Contaminated Soil, Gravel & Water from Utility Construction Activities HM04.series Asbestos Containing Material (ACM) HM05.series PCB Hazardous Materials HM06.series Soil Stockpile Details/Details HM07.series Other Hazardous Materials Civil: CV00.series General Notes, Abbreviations, and Symbols, Survey Controls CV01.series Site Plans CV02.series Demolition Plans CV03.series Sitework/Grading Plans/Profiles/Storm Water Pollution Control Plans CV04.series Pavement Sections CV05.series Typical Details, Drainage Details CV06.series Utility Plans CV07.series Utility Profiles/Sections

CV08.series Utility Details CV09.series Boring Plans/Logs CV10.series Geotechnical Fueling Systems: FU00.series General Notes, Abbreviations, and

Symbols FU01.series Site Plans FU02.series Demolition Fuel Utility Plans FU03.series Fuel Utility Plans FU04.series Fuel Utility Profiles/Sections FU05.series Fueling System Details/Schedules FU06.series EFSO System Plans/Risers/Details Landscape: LA00.series General Notes, Abbreviations, and Symbols LA01.series Site Plan LA02.series Demolition Plans, Plant Removal Plans LA03.series Landscape/Planting Plans LA04.series Elevations LA05.series Landscape Sections LA06.series Irrigation Plans LA07.series Irrigation Details LA08.series Typical Details, Drainage Details LA09.series Plant Schedules LA10.series User Defined Structural Civil (Bridges & Tunnels): SC00.series General Notes, Abbreviations and Symbols SC01.series Site Plan SC02.series Demolition Plans, Temporary Work, Rock



Support Distribution or Support of Excavation SC03.series Key Drawings, Foundation, Retaininig Walls, Instrumentation and Monitoring Plans, and Details SC04.series Approach Slabs, Decks, Plan and Profiles SC05.series Elevations, Longitudinal Sections SC06.series Sections and Details SC07.series Columns and Bents SC08.series Misc. Details, Waterproofing Details SC09.series Schedules, Installation Procedures and Sequence Structural (Buildings): ST00.series General Notes, Abbreviations and Symbols ST01.series Site Plans ST02.series Demolition Plans, Temporary Work ST03.series Key Drawings, Foundation and Framing Plans ST04.series Typical Details ST05.series Foundation, Wall Details ST06.series Sections and Details ST07.series Lagteral Bracing, Special Items ST08.series Misc. Details ST09.series Schedules Architectural: AR00.series General Notes, Abbreviations and Symbols AR01.series Site Plan AR02.series Demolition Plans & Temporary Work AR03.series Key Drawings. Plans: Floor, Roof, Reflected Ceiling AR04.series Detailed Floor Plans AR05.series Elevations: Exterior, Interior AR06.series Sections: Building, Walls AR07.series Vertical Circulation, Stairs, Elevators, Escalators AR08.series Details: Exterior, Interior AR09.series Schedules: Finish, Doors

Interiors: IN00.series General Notes, Abbreviations and Symbols IN01.series Location Plan IN02.series Demolition IN03.series Key drawings, Plans: Floor, Furnishing Reflected Ceilings IN04.series Detailed Floor Plans IN05.series Elevations IN06.series Sections IN07.series User Defined IN08.series Details IN09.series Schedules Equipment: EQ00.series General Notes, Abbreviations and Symbols EQ01.series Site Plan, Work Outside of Building EQ02.series Demolition Plans, Temporary Work EQ03.series Key Drawings, Plans: Floor EQ04.series Detailed Floor Plans, Casework EQ05.series Elevations EQ06.series Sections EQ07.series Riser and Single-line Diagrams for Sub-Ups EQ08.series Details EQ09.series Schedules: Finish, Devices Fire Protection: FP00.series General Notes, Abbreviations and Symbols FP01.series Site Plan FP02.series Demolition Plans FP03.series Floor Plans FP04.series Riser Diagrams FP05.series Piping Flow Diagrams FP06.series Details FP07.series Fire Protection Coverage Zones FP08.series User Defined



Fire Alarm System: FA00.series General Notes, Abbreviations and Symbols FA01.series Site Plan, Work Outside of Building FA02.series Demolition Plans FA03.series Floor Plans FA04.series Riser and Single-Line Diagrams FA05.series Details FA06.series Device Schedules FA07.series Alarm Panel Schedules FA08.series Fire Alarm Zone Diagrams FA09.series User Defined Plumbing: PL00.series General Notes, Abbreviations and Symbols PL01.series Site Plan PL02.series Demolition Plans PL03.series Floor Plans PL04.series Details PL05.series Elevations PL06.series Sections PL07.series Riser Diagrams PL08.series Schedules PL09.series User Defined Mechanical: ME00.series General Notes, Abbreviations and Symbols ME01.series Site Plan ME02.series Demolition Plans ME03.series Floor Plans ME04.series Details ME05.series Elevations ME06.series Sections ME07.series Floor/Riser Diagrams ME08.series Control Diagrams ME09.series Equipment Schedules ME10.series Building Automation and Controls

ME11.series Instrument Loop Diagrams ME12.series Process Drawings ME13.series User Defined Electrical: EL00.series General Notes, Abbreviations and Symbols EL01.series Site Plan EL02.series Demolition Plans EL03.series Lighting Plan EL04.series Power Plans EL05.series Grounding Plans EL06.series Single-Line Diagrams EL07.series Details EL08.series Elevations EL09.series Fixture/Panel Schedules EL10.series Electrical System Controls EL11.series User Defined Communications: CO00.series General Notes, Abbreviations and Symbols CO01.series Site Plans CO02.series Demolition Plans CO03.series Systems Floor Plans CO04.series Riser and Single-line Diagrams CO05.series Details CO06.series Elevations CO07.series Device Schedules CO08.series Panel Schedules CO09.series Wiring Identification Schedules CO10.series User Defined Baggage Handling System: BG00.series General Notes, Abbreviations and Symbols BG01.series Site Plan, Work Outside of Building BG02.series Demolition Plans BG03.series Floor/Conveyor Plans BG04.series Detail Plans and Sections and



Details BG05.series Sections BG06.series Elevations BG07.series Device Subsystem Layouts BG08.series Device Schedules BG09.series Controls Details BG10.series Control Panel Schedules BG11.series User Defined Graphics and Signage System: GR00.series General Notes, Abbreviations and Symbols GR01.series Site Plan, Work Outside of Building GR02.series Demolition Plans GR03.series Floor Plans GR04.series Detailed Sign Face Message Layouts GR05.series Details GR06.series Elevations GR07.series Sign Message Schedules GR08.series Sign Type Details/Substrate Schedules GR09.series Sign Type/Substrate Schedules GR10.series Wiring/Lighting Diagrams and Schedules GR11.series User Defined Security and Access Control System: SS00.series General Notes, Abbreviations and Symbols SS01.series Site Plan, Work Outside of Building SS02.series Demolition Plans SS03.series Floor Plans SS04.series Details SS05.series Elevations SS06.series Riser and Single-line Diagrams SS07.series Device Schedules SS08.series Panel Schedules SS09.series Wiring Identification Schedules SS10.series User Defined Public Information System:

PS00.series General Notes, Abbreviations and Symbols PS01.series Site Plan, Work Outside of Building PS02.series Demolition Plans PS03.series Floor Plans PS04.series Details PS05.series Elevations PS06.series Riser and Single-line Diagrams PS07.series Device Schedules PS08.series Panel Schedules PS09.series Wiring Identification Schedules PS10.series User Defined Aviation Information System: AS00.series General Notes, Abbreviations. and Symbols AS01.series Site Plan, Work Outside of Building AS02.series Demolition Plans AS03.series Floor Plans AS04.series Riser and Single-line Diagrams AS05.series Details AS06.series Elevations AS07.series Device Schedules AS08.series Panel Schedules AS09.series Wiring Identification Schedules AS10.series User Defined Electronic Monitoring System: ES0.series General Notes, Abbrev. and Symbols ES1.series Site Plan, Work Outside of Building ES2.series Demolition Plans ES3.series Floor Plans ES4.series Riser and Single-line Diagrams ES5.series Details ES6.series Elevations ES7.series Device Schedules ES8.series Panel Schedules ES9.series Wiring Identification Schedules ES10.series User Defined Wireless & Radio System:



WS01.series Site Plan, Work Outside of Building WS02.series Demolition Plans WS03.series Floor Plans WS04.series riser and Single-line Diagrams WS05.series Details WS06.series Elevations WS07.series Devices Schedules WS08.series Panel Schedules WS09.series Wiring Indentification Schedules WS10.series User Defined



CHAPTER 4 Model File Level/Layer Assignment Tables

4.1 General

The following pages include naming conventions, level assignment sheets and cell library documentation that supports the development of sheet files and model files. 4.2 Naming Conventions – Model Files and Level/Layer Tables

Table I-4-1 Discipline Designators

Discipline Designator

General GN

Hazardous Materials HM

Civil CV

Fueling Systems FU

Landscape LA

Structural Civil (Bridges & Tunnels SC

Structural (Building) ST

Architectural AR

Interiors IN

Equipment EQ

Fire Protection FP

Fire Alarm System FA

Plumbing PL

Mechanical ME

Electrical EL

Communications CO

Baggage Handling System BG

Graphics & Signage System GR

Security & Access Control System SS

Public Information System PS

Aviation Information System AS

Electronic Monitoring System ES

Wireless & Radio System WS

Table I-4-2 Model File Types

Discipline Code Definition

General

BS* Border Sheet

KP* Keyplan

Hazardous Materials

DT Detail

EL Elevation

LG* Legend

PP* Pollution Prevention Plan

SC Section

XD* Existing/Demolition Plan

Civil

AF* Airfield Plan

AM* Airfield Pavement Marking Plan

CP* Channel Plan

DT Detail

EC* Erosion Control Plan

EL Elevation

FU* Liquid Fuel Utilities Plan

GP* Grading

IP* Installation Plan/Base Map

IW* Industrial Waste Water Plan

JP* Joint Layout Plan

KP* Staking Plan

LG* Legend

NG* Natural Gas Utilities Plan

PL* Project Location Map

PR* Profile





SC Section

SH Schedule

SP Site Plan

SS* Sanitary Sewer Plan

ST* Storm Sewer Plan

TS* Transportation Site Plan

WA* Domestic Water Plan


Fueling Systems

DG Diagram

DT Detail

EL Elevation

EP* Enlarged Plan

LG* Legend

PP* Piping Plan

SH Schedule


Landscape

DT Detail

EL Elevation

IP* Irrigation Plan

LG* Legend

LP* Landscape Plan

SC Section

SH Schedule


Structural

3D Isometric/3D

CP* Column Plan

DT Detail

EL Elevation

EP* Enlarged Plan

FP* Framing Plan

LG* Legend

NB* Non-Building Structures Plan



NP* Foundation Plan

SC Section

SH Schedule


Architectural

3D Isometric/3D

AC* Area Calculations/Occupancy Plan

CP* Reflected Ceiling Plan

DT Detail

EL Elevation

EP* Enlarged Plan

FP Floor Plan

LG* Legend

QP Equipment Plan

RP* Roof Plan

SC Section

SH Schedule


Interiors

3D Isometric/3D

DT Detail

EL Elevation

EP* Enlarged Plan

LG* Legend

QP Equipment Plan

RP* Furniture Plan

SC Section

SH Schedule

SP* Signage Placement Plan

WP* System/Prewired Workstation Plan


Fire Protection

DG Diagram

DT Detail

FA* Fire Alarm/Detection Plan





FP* Fire Suppression Plan

LG* Legend

LP* Life Safety Plan

SH Schedule


Plumbing

DG Diagram

DT Detail

EL Elevation

EP* Enlarged Plan

LG* Legend

PP* Piping Plan

SH Schedule


Mechanical

3D Isometric/3D

DG Diagram

DT Detail

EL Elevation

EP* Enlarged Plan

HP* HVAC Plan

HT* HTCW Utilities Plan

LG* Legend

MD* Machine Design Plan

MH* Material Handling Plan

PP* Piping Plan

QP Equipment Plan

SC Section

SH Schedule

SP* Specialty Piping Plan


Electrical

AL* Airfield Lighting Plan

AP* Auxiliary Power Plan

CP* Exterior Communication Systems Plan

DG Diagram

DT Detail

EU* Electrical Utilities Plan

GP* Grounding System Plan

LG* Legend

LP* Lighting Plan

PP* Power Plan

SH Schedule

SS* Special Systems Plan


Telecommunications

DG Diagram

DT Detail

LG* Legend

SH Schedule

TP* Telephone/Data Plan


* = Not in NCS 2.0



4.3 Level/Layer Assignment Tables – Model Files

This chapter provides the level/layer assignment tables: General:

Border Sheet Cover Sheet Keyplan

Hazardous Materials Demolition Plan Pollution Prevention Plan Sections Details

Civil Demolition Plan Site Plan Grading Plan Eco-Restoration Plan Shore Bankline Navigation Dredging Plan Flood Control Plan Transportation Site Plan Joint Layout Plan Airfield Plan Utilities Plan Profiles Elevations X-Sections Details

Fueling Systems Demolition Plan Piping Plan Details Riser Diagrams

Landscape Demolition Plan Landscape Plan Irrigation Plan Details

Structural Buildings Demolition Plan Foundation Plan Framing Plan Column Plan Elevations Sections Details

Structural Civil Substructure Decks Superstructure Elevations Sections Details

Architectural Demolition Plan Floor Plan Reflected Ceiling Plan Roof Plan Equipment Plan Area Calculations/Occupancy Plan Elevations Sections Details

Interiors Demolition Plan Furniture Plan System Furniture Workstation Plan Signage Placement Plan Floor Patterns Elevations Details



Fire Protection Demolition Plan Life Safety Plan Fire Suppression Plan Details

Fire Alarm System Demolition Plan Fire Alarm/Detection Plan Details Riser Diagrams

Plumbing Demolition Plan Piping Plan Details Riser Diagrams

Mechanical Demolition Plan HVAC Plan Specialty Piping and Equipment Plan HTCW Utilities Plan Material Handling Machine Design Elevations Sections Details Control Diagrams

Electrical Demolition Plan Lighting Plan Power Plan Special Systems Plan Grounding System Plan

Electrical Utilities Plan Exterior Communication Systems Plan Airfield Lighting Plan Details Riser/One-Line Diagrams

Communications Demolition Plan Telephone/Data Plan Riser Diagrams Details

Baggage Handling System Demolition Plan Baggage Handling Plan

Security & Access Control System Demolition Plan Security Plan Riser Diagrams Details

Public Information Systems Demolition Plan Public Information Systems Plan

Aviation Information Systems Demolition Plan Aviation Information Systems Plan

Electronic Monitoring Systems Demolition Plan Electronic Monitoring Systems Plan



4.4 Assignment Tables

TABLE I-4-3 Discipline: General

Model File Type: Border Sheet

Level/Layer Naming Level/Layer Description

Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information

GN-ANNO-MASK Text/shape mask for use with photo backgrounds 0 0.18 113 16

GN-ANNO-NPLT Non-plotting graphic information 0 0.18 5 1

GN-ANNO-RDME Read-me information 0 0.18 5 1

GN-ANNO-SYMB Miscellaneous symbols V 0.35 6 5

GN-ANNO-TEXT Miscellaneous text 0 V V V

GN-ANNO-TTLB Border and titleblock linework V V V V

GN-ANNO-TTLB-GRID Grid lines inside border 7 0.18 5 1

Coordinate Information

GN-PROJ-LALO-COOR Latitude/longitude coordinate grid ticks 0 0.25 2 4

GN-PROJ-LALO-IDEN Latitude/longitude coordinate text 0 0.25 2 4

GN-PROJ-STAT-COOR State plane coordinate grid ticks 3 0.25 2 4

GN-PROJ-STAT-IDEN State plane coordinate text 0 0.25 2 4




Model File Type: Cover Sheet


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information

GN-ANNO-MASK Text/shape mask for use with photo backgrounds 0 0.18 113 16





GN-ANNO-TTLB Border and titleblock linework V V V V




Model File Type: Key Plan


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information

GN-ANNO-KEYN Reference keynotes with associated leaders 0 V V V

GN-ANNO-MATC Match lines 0 0.35 6 5

GN-ANNO-NOTE General notes and general remarks 0 0.35 2 4


GN-ANNO-PATT Patterning, poche, shading, and hatching V 0.18 8 9


GN-ANNO-REFR Reference files (AutoCAD users only) NA NA NA NA



Grid Lines

GN-GRID-COOR X-Y coordinate grid lines 0 0.25 7 0

GN-GRID-COOR-IDEN X-Y coordinate grid lines annotation 0 0.25 7 0

GN-GRID-EXTR Column grid outside building 7 0.18 5 1

GN-GRID-IDEN Column grid tags 0 0.25 1 3

GN-PLAN-OTLN Floor outline/perimeter/building footprint 0 0.35 6 5

Floor Information

G-PLAN-OTLN Floor outline/perimeter/building footprint 0 0.35 6 5

Site Information

GN-SITE-OTLN Site plan - key map 0 0.35 6 5



4.5 Hazardous Materials

TABLE I-4-6 Discipline: Hazardous Materials

Model File Type: Demolition Plan


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information

HM-ANNO-DIMS Witness extension lines, dimensions arrowheads and text 0 V V V

HM-ANNO-KEYN Keynote with associated leaderlines and arrowheads 0 V V V

HM-ANNO-NPLT Construction lines, reference targets, area calculations V 0 5 1

HM-ANNO-PATT Miscellaneous patterning 0 0 8 9

HM-ANNO-NOTE General note and general remarks 0 2 2 4

HM-ANNO-SYMB Reference bubbles, matchlines, breaklines V 2 6 5

HM-ANNO-TEXT Detail title text, leaderlines, arrowheads, notes 0 V V V

HM-STAT-DEMO Demolition 2 2 6 5

HM-STAT-EXST Existing to remain 0 1 3 2

HM-STAT-MOVE Items to be moved 5 2 6 5

HM-STAT-NICN Not in contract 3 0 8 9

HM-STAT-PHS# Phase numbers (# = 1-9) 0 2 2 4

HM-STAT-RELO Relocated items 2 0 5 1

HM-STAT-TEMP Temporary work 4 3 4 7

HM-DEMO-HAZW Hazardous waste 0 2 6 5




Model File Type: Pollution Prevention Plan


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information

HM-ANNO-DIMS Witness/extension lines, dimension terminators, dimension 0 V V V

HM-ANNO-KEYN Reference keynotes with associated leaders 0 V V V

HM-ANNO-NOTE General notes and general remarks 0 0.35 2 4

HM-ANNO-NPLT Non-plotting graphic information 0 0.18 5 1

HM-ANNO-PATT Patterning, poche, shading, and hatching V 0.18 8 9

HM-ANNO-RDME Read-me information 0 0.18 5 1

HM-ANNO-REFR Reference files (AutoCAD users only) NA NA NA NA

HM-ANNO-SYMB Miscellaneous symbols V V 6 5

HM-ANNO-TEXT Miscellaneous text and callouts with associated leaders 0 V V V

Buildings

HM-BLDG-IDEN Annotation 0 0.35 2 4

HM-BLDG-OTLN Command posts, information centers 0 0.35 2 4

Decontamination

HM-DECN-EQPM Decontamination equipment 0 0.25 1 3

HM-DECN-IDEN Annotation 0 0.35 6 5

Disposal Areas

HM-DISP-HAZW Hazardous waste 0 0.18 5 1

HM-DISP-IDEN Annotation 0 0.35 6 5

HM-DISP-MUNT Munitions 0 0.18 5 1

HM-DISP-TANK Spill containment tanks 0 0.35 6 5

Emergency Fixtures

HM-FIXT-EYEW Emergency eyewashes 0 0.25 3 2

HM-FIXT-SHWR Emergency showers 0 0.25 3 2

Monitoring Stations

HM-MNST-AIRQ Air quality 0 0.25 3 2

HM-MNST-GWTR Ground water 0 0.25 3 2

HM-MNST-IDEN Annotation 0 0.25 3 2

HM-MNST-LAND Landfill gas 0 0.25 3 2

HM-MNST-SOIL Soil gas 0 0.25 3 2




Model File Type: Pollution Prevention Plan


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

HM-MNST-SWTR Surface water 0 0.25 3 2

Pollution Areas

HM-POLL-CONC Polluted area of concern 0 0.35 2 4

HM-POLL-IDEN Annotation 0 0.35 2 4

HM-POLL-ORIG Point of pollution origin 0 0.35 2 4

HM-POLL-POTN Potential spill, emission, or release source 0 0.35 2 4

Sample Points

HM-SAMP-AIRS Air samples 0 0.25 1 3

HM-SAMP-BIOL Biological samples 0 0.25 1 3

HM-SAMP-GWTR Ground water samples 0 0.25 1 3

HM-SAMP-IDEN Annotation 0 0.25 1 3

HM-SAMP-MAGN Magnetometer location points 0 0.25 1 3

HM-SAMP-SEDI Sediment samples 0 0.25 1 3

HM-SAMP-SOIL Soil samples 0 0.25 1 3

HM-SAMP-SOLI Solid material samples 0 0.25 1 3

HM-SAMP-SWTR Surface water samples 0 0.25 1 3

HM-SAMP-WAST Waste samples 0 0.25 1 3

Storage Facilities

HM-STOR-HAZM Hazardous materials 0 0.35 6 5

HM-STOR-HAZW Hazardous waste 0 0.35 6 5

HM-STOR-IDEN Annotation 0 0.35 6 5




Model File Type: Sections


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information

HM-ANNO-DIMS Witness/extension lines, dimension terminators, dimension text 0 V V V





HM-ANNO-RDME Read-me information 0 0.18 5 1




Sections

HM-SECT-IDEN Component identification numbers 0 0.35 2 4

HM-SECT-MBND Material beyond section cut 0 0.18 5 1

HM-SECT-MCUT Material cut by section 0 0.50 4 7

HM-SECT-PATT Textures and hatch patterns 0 0.18 8 9




Model File Type: Details

Level/Layer Description

Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information

HM-ANNO-DIMS Witness/extension lines, dimension terminators, dimension text 0 V V V





HM-ANNO-RDME Read-me information V 0.18 5 1




Detail Information

HM-DETL-GRPH Graphics, gridlines, non-text items V V V V

HM-DETL-INPD Inch-pound specific dimensions and notes 0 V V V

HM-DETL-METR Metric specific dimensions and notes 0 V V V



4.6 Civil

TABLE I-4-10 Discipline: Civil



Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information

CV-ANNO-DIMS Witness extension lines, dimensions arrowheads and text 0 V V V

CV-ANNO-KEYN Keynote with associated leaderlines and arrowheads 0 V V V

CV-ANNO-NPLT Construction lines, reference targets, area calculations V 0 5 1

CV-ANNO-PATT Miscellaneous patterning 0 0 8 9

CV-ANNO-NOTE General note and general remarks 0 2 2 4

CV-ANNO-SYMB Reference bubbles, matchlines, breaklines V 2 6 5

CV-ANNO-TEXT Detail title text, leaderlines, arrowheads, notes 0 V V V

CV-STAT-DEMO Demolition 2 2 6 5

CV-STAT-EXST Existing to remain 0 1 3 2

CV-STAT-MOVE Items to be moved 5 2 6 5

CV-STAT-NICN Not in contract 3 0 8 9

CV-STAT-PHS# Phase numbers (# = 1-9) 0 2 2 4

CV-STAT-RELO Relocated items 2 0 5 1

CV-STAT-TEMP Temporary work 4 3 4 7

CV-DEMO-HAZW Hazardous waste 0 2 6 5




Model File Type: Site Plan


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information

CV-ANNO-DIMS Witness/extension lines, dimension terminators, dimension text 0 V V V

CV-ANNO-KEYN Reference keynotes with associated leaders 0 V V V

CV-ANNO-MASK Text/shape mask for use with photo backgrounds 0 0.18 113 16

CV-ANNO-NOTE General notes and general remarks 0 0.35 2 4

CV-ANNO-NPLT Non-plotting graphic information 0 0.18 5 1

CV-ANNO-PATT Patterning, poche, shading, and hatching V 0.18 8 9

CV-ANNO-RDME Read-me information 0 0.18 5 1

CV-ANNO-REFR Reference files (AutoCAD users only) NA NA NA NA

CV-ANNO-SYMB Miscellaneous symbols V V 6 5

CV-ANNO-TEXT Miscellaneous text and callouts with associated leaders 0 V V V

Alignments

CV-ALGN-DATA Alignment coordinates and curve data 0 0.35 3 2

CV-ALGN-LINE Alignments 4 0.35 2 4

CV-ALGN-MAJR Alignment major stationing and tick marks 0 0.35 1 3

CV-ALGN-MARK Alignment tick marks 0 0.35 3 2

CV-ALGN-MINR Alignment minor stationing and tick marks 0 0.18 6 5

CV-ALGN-STAT Alignment stationing and tick marks, alignment PI stations 0 0.35 3 2

CV-ALGN-SYMB Alignment symbols (PIs) 0 0.35 6 5

CV-ALGN-TEXT Alignment text, annotation with associated leaders 0 0.35 2 4

Building and Primary Structures

CV-BLDG-DECK Outdoor decks (attached, no roof overhead) 0 0.50 4 7

CV-BLDG-DOCK Loading docks 0 0.50 4 7

CV-BLDG-IDEN Building and other structure annotation 0 0.35 2 4

CV-BLDG-OTLN Building and other structure outlines 0 0.70 7 0

CV-BLDG-OVHD Building overhangs 0 0.50 4 7

CV-BLDG-PRCH Porches (attached, roof overhead) 0 0.50 4 7

Borrow Areas

CV-BORW-IDEN Borrow/spoil area annotation 0 0.35 2 4

CV-BORW-LINE Borrow/spoil area 2 0.35 2 4






Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

Bridges

CV-BRDG-CNTR Bridge centerlines 7 0.25 1 3

CV-BRDG-CTLJ Control joints 0 0.25 4 7

CV-BRDG-DECK Bridge deck 0 0.50 4 7

CV-BRDG-IDEN Bridge annotation 0 0.35 2 4

CV-BRDG-OTLN Bridge outlines 0 0.50 4 7

CV-BRDG-RAIL Bridge railing 0 0.25 4 7

Channels

CV-CHAN-BANK-IDEN Channel/canal top of bank annotation 0 0.35 2 4

CV-CHAN-BANK-TOP Channel/canal top of bank 0 0.35 2 4

CV-CHAN-BNCH Channel/canal bench design feature lines (breaklines form DTMs) 0 0.35 2 4

CV-CHAN-BWTR Breakwaters 0 0.35 6 5

CV-CHAN-CNTR Channel centerline and survey report lines 7 0.18 5 1

CV-CHAN-CNTR-IDEN Channel centerline and survey report lines - annotation 0 0.35 5 1

CV-CHAN-DACL De-authorized channel limits, anchorages, etc. 0 0.35 3 2

CV-CHAN-DACL-IDEN De-authorized channel limits, anchorages, etc. - annotation 0 0.35 3 2

CV-CHAN-DOCK Docks, decks, floats, piers, and mooring facilities 0 0.35 6 5

CV-CHAN-LIMT Channel limits, anchorages, turning basins, disposal areas, etc. 0 0.35 6 5

CV-CHAN-LIMT-IDEN Channel limits, anchorages, turning basins, disposal areas, etc. - annotation 0 0.35 6 5

CV-CHAN-NAID Navigation aids and text 0 0.35 V V

CV-CHAN-SLOP-LINE Channel cut/fill slope (Indicates cut and fill lines) 0 0.35 4 7

CV-CHAN-SPOL Spoil limits 0 0.50 4 7

CV-CHAN-SYMB Channel/canal symbols 0 0.35 6 5

CV-CHAN-TEXT Channel/canal text, annotation with associated leaders 0 0.35 2 4

CV-CHAN-TOE Channel/canal toe 3 0.50 5 1

CV-CHAN-TOE-IDEN Channel/canal toe annotation 0 0.35 6 5

CV-CHAN-TURN Turning Points 0 0.35 2 4

CV-CHAN-WIDE Channel/canal widener 3 0.50 4 7

Domestic Water






Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

CV-DOMW-ABND-PIPE Abandoned Piping 2 0.35 6 5

CV-DOMW-HYDR Hydrants 0 0.35 1 3

CV-DOMW-IDEN Identifier tags, symbol modifier, and text 0 0.35 2 4

CV-DOMW-MAIN-PIPE Main domestic water piping WATERL 0.35 6 5

CV-DOMW-PITS-VLVE Valve pits/vaults 0 0.35 3 2

CV-DOMW-STNS-IDEN Identifier tags, symbol modifier, and text 0 0.35 2 4

CV-DOMW-STNS-PUMP Booster pump stations 0 0.35 6 5

CV-DOMW-STNS-REDC Pressure reducing stations 0 0.35 6 5

CV-DOMW-TANK Water storage tanks 0 0.35 1 3

CV-DOMW-WELL Water well houses 0 0.35 1 3

Dredging

CV-DRED-IDEN Dredging annotation 0 0.35 2 4

CV-DRED-LIMT Dredge limit lines 0 0.50 4 7

CV-DRED-OHWM Ordinary high water marks 0 0.35 2 4

Ditches or Washes

CV-DTCH-BOTD Bottom of ditch or wash 0, DITCH 0.25 3 2

CV-DTCH-CNTR Centerline of ditch or wash 7 0.18 5 1

CV-DTCH-EWAT Edge of water 0 0.25 4 7

CV-DTCH-IDEN Ditches and washes annotation 0 0.35 3 2

CV-DTCH-TOP~ Top of ditch or wash 0 0.25 3 2

Erosion and Sediment Control (Temporary/Construction)

CV-EROS-CIPR Culvert inlet protection V 0.25 3 2

CV-EROS-CNTE Construction entrance V 0.35 6 5

CV-EROS-DDIV Drainage divides 0 0.50 4 7

CV-EROS-DVDK Diversion dike 0 0.50 4 7

CV-EROS-IDEN Erosion and sediment control annotation 0 0.35 3 2

CV-EROS-INPR Inlet protection V 0.25 3 2

CV-EROS-SILT Silt fence SILT 0.35 2 4






Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

CV-EROS-SILT-CHCK Silt check 0 0.35 2 4

CV-EROS-SILT-TRAP Silt trap 0 0.35 2 4

CV-EROS-SSLT Super silt fence SSILT 0.35 2 4

Flood Hazard Area

CV-FLHA-025Y 25 year mark 6 0.35 6 5





CV-FLHA-IDEN Flood hazard area annotation 0 0.35 2 4

Floodwalls

CV-FLOD-BASE Floodwall base of wall 0 0.50 20 6

CV-FLOD-BASE-IDEN Floodwall base of wall annotation 0 0.35 20 6

CV-FLOD-CNTR Floodwall centerline 7 0.18 20 6

CV-FLOD-CNTR-IDEN Floodwall centerline annotation 0 0.35 20 6

CV-FLOD-DRAN Floodwall toe drain 0 0.35 6 5

CV-FLOD-DRAN-IDEN Floodwall toe drain annotation 0 0.35 6 5

CV-FLOD-PILE Floodwall sheet piling 0 0.50 22 22

CV-FLOD-PILE-IDEN Floodwall sheet piling annotation 0 0.35 22 22

CV-FLOD-TOE~ Floodwall toe outline 0 0.35 4 7

CV-FLOD-TOP~ Floodwall top of wall 0 0.50 2 4

CV-FLOD-TOP~-IDEN Floodwall top of wall annotation 0 0.35 20 6

Liquid Fuel

CV-FUEL-ABND-PIPE Abandoned piping 2 0.35 6 5

CV-FUEL-IDEN Identifier tags, symbol modifier, and text 0 0.35 2 4

CV-FUEL-MAIN-PIPE Main fuel piping LIQPET 0.35 6 5

CV-FUEL-PITS-HYDR Hydrant control pits 0 0.35 3 2

CV-FUEL-PITS-VLVE Valve pits 0 0.35 3 2

CV-FUEL-TANK Fuel tanks 0 0.35 3 2

Grade Linework






Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

CV-GRAD-DSGN Design grade (proposed) 0 0.35 3 2

CV-GRAD-EXST Existing grade, ground line 3 0.35 6 5

CV-GRAD-FNSH Finished grade 0 0.50 4 7

CV-GRAD-FNSH-PRP1 Proposed Surface #1 0 0.35 8 9




CV-GRAD-GTXL Geotextile placement grade 0 0.25 2 4

CV-GRAD-IDEN Grade annotation for cross sections and profiles 0 0.35 2 4

CV-GRAD-SCLN Stability control line 7 0.50 5 1

CV-GRAD-WATR Water surface in section view 0 0.35 2 4

Industrial Waste Water

CV-INDW-ABND-PIPE Abandoned piping 2 0.35 6 5

CV-INDW-IDEN Identifier tags, symbol modifier, and text 0 0.35 2 4

CV-INDW-MAIN-PIPE Main industrial waste water piping IWASTE 0.35 6 5

Irrigation

CV-IRRG-EQPM Irrigation equipment (e.g., controllers, valves, etc.) 0 0.35 2 4

CV-IRRG-IDEN Irrigation annotation 0 0.35 2 4

CV-IRRG-PIPE Irrigation piping 0 0.35 6 5

Levees

CV-LEVE-BANK-IDEN Levee top of bank annotation 0 0.25 20 6

CV-LEVE-BANK-TOP Levee top of bank 0 0.35 2 4

CV-LEVE-BERM Levee berm outline 0 0.35 6 5

CV-LEVE-BNCH Levee bench design feature lines (breaklines form DTMs) 0 0.35 20 6

CV-LEVE-BNCH-IDEN Levee bench annotation 0 0.25 2 4

CV-LEVE-BRRW Borrow limits 0 0.50 4 7

CV-LEVE-CNTR Levee centerline 7 0.18 20 6

CV-LEVE-CNTR-IDEN Levee centerline annotation 0 0.35 20 6

CV-LEVE-IDEN Levee annotation 0 0.35 2 4

CV-LEVE-OTLN Levee outline 0 0.50 4 7






Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

CV-LEVE-SLOP Levee slope indicator with annotation 0 0.35 2 4

CV-LEVE-STAT Levee stationing 0 0.35 2 4

CV-LEVE-TOE Levee toe 2 0.35 20 6

CV-LEVE-TOE-IDEN Levee toe annotation 0 0.25 20 6

Police Ranges

CV-POLC-BATP Battle positions 0 0.50 4 7

CV-POLC-CAMS Range cameras 0 0.35 6 5

CV-POLC-FOXH Fox holes and pits 0 0.35 6 5

CV-POLC-MATS Moving army targets 0 0.50 4 7

CV-POLC-MITS Moving infantry targets 0 0.50 4 7

CV-POLC-MITS-IDEN Moving infantry targets annotation 0 0.35 2 4

CV-POLC-PUTS Pop up targets 0 0.50 4 7

CV-POLC-PUTS-IDEN Pop up targets annotation 0 0.35 2 4

CV-POLC-SATS Stationary army targets 0 0.50 4 7

CV-POLC-SATS-IDEN Stationary army targets annotation 0 0.35 2 4

CV-POLC-SITS Stationary infantry targets 0 0.50 4 7

CV-POLC-SITS-IDEN Stationary infantry targets annotation 0 0.35 2 4

Natural Gas

CV-NGAS-ABND-PIPE Abandoned piping 2 0.35 6 5

CV-NGAS-IDEN Identifier tags, symbol modifier, and text 0 0.35 2 4

CV-NGAS-MAIN-PIPE Main natural gas piping NTGASN 0.35 6 5

CV-NGAS-PITS-VLVE Valve pits/boxes 0 0.35 3 2

CV-NGAS-TANK Tanks 0 0.25 3 2

Parking Lots

CV-PRKG-CARS Graphic illustration of cars 0 0.35 2 4

CV-PRKG-CNTR Parking lot centerlines 7 0.25 1 3

CV-PRKG-CNTR-IDEN Parking lot centerline annotation 0 0.25 1 3

CV-PRKG-CURB Curbs and gutters 0 0.35 3 2

CV-PRKG-DRAN Drainage slope indications 0 0.35 1 3

CV-PRKG-FIXT Parking lot fixtures (e.g., wheel stops, parking meters) 0 0.35 91 106






Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

CV-PRKG-FLNE Fire lanes 0 0.25 1 3

CV-PRKG-IDEN Parking lot annotation 0 0.35 6 5

CV-PRKG-MRKG Pavement markings 0 0.35 2 4

CV-PRKG-OTLN Parking lot outlines 0 0.50 4 7

CV-PRKG-SIGN Signs 0 0.35 2 4

Property

CV-PROP-CONS Construction limits/controls, staging area CONLMT 0.70 7 0

CV-PROP-ESMT Easements CONEMT 0.70 7 0

CV-PROP-IDEN Property annotation 0 0.35 6 5

CV-PROP-RWAY Right of ways 6 0.70 7 0

CV-PROP-RWAY-ACQU Right of way to be acquired in perpetuity 0 0.70 7 0

CV-PROP-SECT Section lines 7 0.50 6 5

CV-PROP-SECT-IDEN Section lines annotation 0 0.35 6 5

CV-PROP-TSHP Township/range lines 4 0.50 6 5

CV-PROP-TSHP-IDEN Township/range lines annotation 0 0.35 6 5

Pavement

CV-PVMT-ASPH Pavement pattern - asphalt 0 0.18 8 9

CV-PVMT-CONC Pavement pattern - concrete 0 0.18 8 9

CV-PVMT-GRVL Pavement pattern - gravel 0 0.18 8 9

CV-PVMT-IDEN Road, parking lot, railroad, airfield pavement annotation 0 0.25 2 4

CV-PVMT-MRKG Pavement markings 0 0.35 2 4

CV-PVMT-PATT Joint patterns, text and dimensions 0 0.35 2 4

Rivers

CV-RIVR-BANK-TOP Top of river bank 0 0.35 5 1

CV-RIVR-BOTM River bottom 0 0.35 5 1

CV-RIVR-CNTR Centerline of river 7 0.25 1 3

CV-RIVR-EDGE River edge 0 0.50 5 1

CV-RIVR-IDEN Identifier tags, symbol modifiers, and text 0 0.35 2 4

Roads, Streets, and Highways






Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

CV-ROAD-ASPH Road outlines - asphalt surface 0 0.25 8 9

CV-ROAD-CNTR Road centerlines 7 0.25 1 3

CV-ROAD-CNTR-IDEN Road centerline annotation 0 0.25 1 3

CV-ROAD-CONC Road outlines - concrete surface 0 0.25 7 0

CV-ROAD-CURB Curbs and gutters 0 0.35 6 5

CV-ROAD-GRAL Guard rails GUARD 0.35 6 5

CV-ROAD-GRVL Road outlines - gravel surface 0 0.25 20 6

CV-ROAD-IDEN Road, street, highway annotation 0 0.35 6 5

CV-ROAD-MRKG Pavement markings 0 0.35 2 4

CV-ROAD-PATT Joint patterns, text and dimensions 0 0.35 2 4

CV-ROAD-SHLD Roadway shoulder 0 0.35 6 5

CV-ROAD-SIGN Signs 0 0.25 1 3

CV-ROAD-UPVD Road outlines - unpaved surface 0 0.25 3 2

Riprap and Other Permanent Erosion Control Items

CV-RRAP-GABN Gabions V 0.25 1 3

CV-RRAP-MATS Articulated concrete mats V 0.25 3 2

CV-RRAP-RVMT Revetments V 0.25 1 3

CV-RRAP-WEIR Weirs V 0.25 3 2

Site Features

CV-SITE-BLIN Site breakline 2 0.35 3 2

CV-SITE-FENC Fences and handrails 0, FENCE 0.35 6 5

CV-SITE-FENC-IDEN Fence, handrail, ramp, and trail annotation 0 0.35 6 5

CV-SITE-IDEN Site feature annotation 0 0.35 6 5

CV-SITE-STRC Structures (bridges, sheds, foundation pads, footings, etc.) 0 0.35 22 22

CV-SITE-STRS Stairs and ramps 0 0.35 6 5

CV-SITE-WALK Walks, trails and bicycle paths 0 0.35 2 4

Sanitary Sewer

CV-SSWR-ABND-PIPE Abandoned piping 2 0.35 6 5

CV-SSWR-DEVC Grease traps, grit chambers, flumes, neutralizers, oil/water separators, ejectors, and valves 0 0.35 6 5






Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

CV-SSWR-DEVCV-IDEN Identifier tags, symbol modifier, and text 0 0.25 6 5

CV-SSWR-FTTG Caps and cleanouts 0 0.35 6 5

CV-SSWR-IDEN Identifier tags, symbol modifier, and text 0 0.35 2 4

CV-SSWR-JBOX Junction boxes and manholes 0 0.35 1 3

CV-SSWR-MAIN-PIPE Sanitary sewer piping SSWAF 0.35 6 5

CV-SSWR-TANK Septic tanks 0 0.35 3 2

Storm Sewer

CV-STRM-ABND-PIPE Abandoned piping 2 0.35 6 5

CV-STRM-CULV Culverts CULVRT 0.35 3 2

CV-STRM-DEVC Downspouts, flumes, oil/water separators, and flap gates 0 0.35 6 5

CV-STRM-FTTG Caps and cleanouts 0 0.35 6 5

CV-STRM-HDWL Headwalls and endwalls 0 0.50 7 0

CV-STRM-IDEN Identifier tags, symbol modifier, and text 0 0.35 2 4

CV-STRM-MAIN-PIPE Storm sewer piping STRAF 0.35 6 5

CV-STRM-MHOL Manholes 0 0.35 1 3

CV-STRM-STNS-PUMP Pump stations 0 0.35 6 5

Survey

CV-SURV-DATA Survey data (benchmarks and horizontal control points or monuments) 0 0.35 6 5

CV-SURV-IDEN Survey, baseline, and control line annotation 0 0.35 6 5

CV-SURV-LINE Survey, baseline, and control lines 2 0.35 4 7

Topography

CV-TOPO-BDRY-EXTR Surface exterior boundary 0 0.18 3 2

CV-TOPO-BDRY-INTR Surface interior boundary 2 0.18 1 3

CV-TOPO-BKLN Breaklines 4 0.50 7 0

CV-TOPO-BKLN-COMM Subsurface utilities communications breakline COMUG

N 0.50 7 0

CV-TOPO-BKLN-DOMW Subsurface utilities water breakline WATERL 0.50 7 0

CV-TOPO-BKLN-ELEC Subsurface utilities electric breakline EPUGN 0.50 7 0






Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

CV-TOPO-BKLN-FUEL Subsurface utilities liquid fuel breakline LIQPET 0.50 7 0

CV-TOPO-BKLN-NGAS Subsurface utilities natural gas breakline NTGASN 0.50 7 0

CV-TOPO-BKLN-SSWR Subsurface utilities sanitary sewer breakline SSWAF 0.50 7 0

CV-TOPO-BKLN-STRM Subsurface utilities storm sewer breakline STRAF 0.50 7 0

CV-TOPO-BORE Boring locations and text 0 0.35 6 5

CV-TOPO-COOR Coordinate grid ticks and text 0 0.35 122 23

CV-TOPO-COOR-LALO Latitude and longitude grid ticks 0 0.25 3 2

CV-TOPO-COOR-STAT State Plane coordinate ticks 0 0.25 3 2

CV-TOPO-DTMO DTM obscure area boundary 0 0.35 6 5

CV-TOPO-DTMP DTM points 0 0.35 6 5

CV-TOPO-DTMT DTM triangles 0 0.35 22 22

CV-TOPO-MAJR Major contours 0 0.35 2 4

CV-TOPO-MAJR-IDEN Major contours - annotation 0 0.35 2 4

CV-TOPO-MINR Minor contours 0 0.25 3 2

CV-TOPO-MINR-IDEN Minor contours - annotation 0 0.25 3 2

CV-TOPO-SHAP Inroads generated shapes/lines 0 0.25 1 3

CV-TOPO-SHOR Shorelines, land features, and references 0 0.35 4 7

CV-TOPO-SLOP-FILL Cut/fill slopes 0 0.35 2 4

CV-TOPO-SLOP-IDEN Cut/fill slope, top/toe slope annotation 0 0.35 2 4

CV-TOPO-SLOP-TOPT Top/toe slopes 0 0.35 6 5

CV-TOPO-SOUN Soundings and overbanks 0 0.18 V V

CV-TOPO-SPOT Spot elevations 0 0.35 2 4

CV-TOPO-SURF-PERM Surface perimeter 0 0.18 3 2

CV-TOPO-SURF-PONT Surface feature points 0 0.25 7 0

CV-TOPO-SURF-VOID Surface void region 0 0.18 1 3

CV-TOPO-WATR Water level reference (LWRP, after-grading LWRP, SWL, etc) 3 0.50 V V

Elevations

CV-ELEV-FIXT Miscellaneous fixtures 0 0.35 2 4






Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

CV-ELEV-IDEN Component identification numbers 0 0.35 2 4

CV-ELEV-OTLN Building outlines 0 0.35 6 5

CV-ELEV-PATT Textures and hatch patterns 0 0.18 8 9

CV-ELEV-SIGN Signage 0 0.35 1 3




Model File Type: Grading Plan


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information











Alignments
















Borrow Areas








Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor












Topography























Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor









Model File Type: Eco-Restoration Plan


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information










Alignments










Habitats/Landforms

CV-ECCO-BURR Burrow 0 0.50 4 7

CV-ECCO-DENS Den 0 0.50 4 7

CV-ECCO-GATR Gator hole 2 0.35 6 5

CV-ECCO-HUMK Hummocks 0 0.35 6 5

CV-ECCO-IDEN Habitat annotation 0 0.35 2 4

CV-ECCO-NEST Nest, nesting tree 0 0.50 4 7

CV-ECCO-PRCH Perch/nesting hole 0 0.50 4 7

Grade Linework







Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor


Irrigation




Shore Bankline

CV-SHOR-BANK-TOP Shore top of bank 0 0.25 6 5

CV-SHOR-BKLN Shore breakline 2 0.35 5 1

CV-SHOR-BLIN Shore baseline and control line 0 0.50 4 7

CV-SHOR-BLIN-IDEN Shore baseline and control line annotation 0 0.25 4 7

CV-SHOR-BNCH Shore bench 6 0.35 22 22

CV-SHOR-CNTR Shore centerline 7 0.25 5 1

CV-SHOR-CNTR-IDEN Shore centerline annotation 0 0.25 6 5

CV-SHOR-ELIN Shore erosion control line 0 0.50 4 7

CV-SHOR-ELIN-IDEN Shore erosion control line annotation 0 0.25 6 5

CV-SHOR-LIMT Shore limit lines 0 0.50 4 7

CV-SHOR-OHWM Ordinary high water marks 0 0.35 2 4

CV-SHOR-OTLN Shore outline 0 0.25 2 4

CV-SHOR-SLOP-IDEN Shore slope indicator with annotation 0 0.25 7 0

CV-SHOR-SLOP-TOP Shore top of slope 2 0.35 22 22

CV-SHOR-SYMB Shore symbols 0 0.18 6 5

CV-SHOR-TOE Shore toe 3 0.50 5 1

CV-SHOR-TOE-IDEN Shore toe annotation 0 0.25 7 0

Topography












Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor











Wetlands

CV-WETL-BOGS Bogs 0 0.35 6 5

CV-WETL-FENS Fens 0 0.35 2 4

CV-WETL-IDEN Wetland annotation 0 0.35 2 4

CV-WETL-MRSH Fresh water marshes 0 0.35 162 33

CV-WETL-MRSH-SALT Tidal saltwater marshes 0 0.35 162 33

CV-WETL-MRSH-TIDL Tidal freshwater marsh 0 0.35 162 33

CV-WETL-PCSN Pocosins 0 0.35 6 5

CV-WETL-PHOL Vernal pools, playas, prairie potholes, wet meadows, and wet prairies 0 0.35 6 5

CV-WETL-RPRN Riparian forested wetlands 0 0.35 162 33

CV-WETL-SLGH Sloughs 0 0.35 162 33

CV-WETL-SWMP Swamps 0 0.35 162 33




Model File Type: Shore Bankline


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information










Alignments










Borrow Areas



Channels


Dredging









Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

Grade Linework








Shore Bankline

CV-SHOR-BANK-TOP Shore top of bank 0 0.25 6 5

CV-SHOR-BKLN Shore breakline 2 0.35 5 1

CV-SHOR-BLIN Shore baseline and control line 0 0.50 4 7

CV-SHOR-BLIN-IDEN Shore baseline and control line annotation 0 0.25 4 7

CV-SHOR-BNCH Shore bench 6 0.35 22 22

CV-SHOR-CNTR Shore centerline 7 0.25 5 1

CV-SHOR-CNTR-IDEN Shore centerline annotation 0 0.25 6 5

CV-SHOR-ELIN Shore erosion control line 0 0.50 4 7

CV-SHOR-ELIN-IDEN Shore erosion control line annotation 0 0.25 6 5

CV-SHOR-LIMT Shore limit lines 0 0.50 4 7

CV-SHOR-OHWM Ordinary high water marks 0 0.35 2 4

CV-SHOR-OTLN Shore outline 0 0.25 2 4

CV-SHOR-SLOP-IDEN Shore slope indicator with annotation 0 0.25 7 0

CV-SHOR-SLOP-TOP Shore top of slope 2 0.35 22 22

CV-SHOR-SYMB Shore symbols 0 0.18 6 5

CV-SHOR-TOE Shore toe 3 0.50 5 1

CV-SHOR-TOE-IDEN Shore toe annotation 0 0.25 7 0

Storm Sewer









Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor





Survey




Topography



N 0.50 7 0























Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor




Elevations









Model File Type: Navigation Dredging Plan


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information










Alignments















Borrow Areas



Bridges







Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor






Channels



















CV-CHAN-TURN

Turning points 0 0.35 2 4


Domestic Water

CV-DOMW-ABND-PIPE Abandoned piping 2 0.35 6 5






Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

CV-DOMW-DEVC Connectors, faucets, reducers, regulators, vents, intake points, taps, backflow preventers, and valves 0 0.35 6 5

CV-DOMW-FIRE Fire lines FIRE 0.25 1 3

CV-DOMW-FTTG Caps, cleanouts, crosses, and tees 0 0.35 6 5




CV-DOMW-METR Meters 0 0.35 3 2

CV-DOMW-NPOT-HYDR Non-potable hydrants/flushing hydrants 0 0.35 1 3

CV-DOMW-NPOT-PIPE Non-potable water piping NONPOT 0.35 6 5

CV-DOMW-PITS-IDEN Identifier tags, symbol modifier, and text 0 0.35 3 2

CV-DOMW-PITS-VENT Vent pits 0 0.35 3 2


CV-DOMW-SERV-PIPE Domestic water service piping 0 0.35 6 5

CV-DOMW-SIGN Surface markers/signs 0 0.35 1 3

Dredging




Liquid Fuel







Grade Linework








Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor














Levees















Natural Gas







Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor




Property










Pavement







Rivers

CV-RIVR-BANK-TOP Top of river bank 0 0.35 5 1













Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor



Sanitary Sewer





Storm Sewer








Survey




Topography





N 0.50 7 0










Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor



























Model File Type: Flood Control Plan


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information











Alignments










Borrow Areas



Bridges











Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor


Channels



















CV-CHAN-TURN

Turning points 0 0.35 2 4


Domestic Water










Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

















Dredging




Ditches or Washes

CV-DTCH-BOTD Bottom of ditch or wash 0, DITCH 0.25 3 2

CV-DTCH-CNTR Centerline of ditch or wash 7 0.18 5 1

CV-DTCH-EWAT Edge of water 0 0.25 4 7

CV-DTCH-IDEN Ditches and washes annotation 0 0.35 3 2

CV-DTCH-TOP Top of ditch or wash 0 0.25 3 2







Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor











Flood Hazard Area






CV-FLHA-IDEN Flood hazard area annotation 0 0.35 2 4

Floodwalls

CV-FLOD-BASE Floodwall base of wall 0 0.50 20 6

CV-FLOD-BASE-IDEN Floodwall base of wall annotation 0 0.35 20 6








CV-FLOD-TOE Floodwall toe outline 0 0.35 4 7

CV-FLOD-TOP Floodwall top of wall 0 0.50 2 4

CV-FLOD-TOP-IDEN Floodwall top of wall annotation 0 0.35 20 6






Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

Grade Linework















Levees




















Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

Parking Lots












Property










Pavement







Rivers






Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

CV-RIVR-BANK-TOP~ Top of river bank 0 0.35 5 1
























Site Features

CV-SITE-BLIN Site breakline 2 0.35 3 2

CV-SITE-FENC Fences and handrails 0, FENCE 0.35 6 5

CV-SITE-FENC-IDEN Fence, handrail, ramp, and trail annotation 0 0.35 6 5


CV-SITE-STRC Structures (bridges, sheds, foundation pads, footings, etc.) 0 0.35 22 22






Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

CV-SITE-STRS Stairs and ramps 0 0.35 6 5

CV-SITE-WALK Walks, trails and bicycle paths 0 0.35 2 4

Sanitary Sewer





Storm Sewer









Survey




Topography





N 0.50 7 0









Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

























Elevations









Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor






Model File Type: Transportation Site Plan


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information











Alignments









Bridges







Parking Lots








Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor










Pavement





Railroads

CV-RAIL-CNTR Railroad track centerlines 7 0.25 1 3

CV-RAIL-CNTR-IDEN Railroad track centerline annotation 0 0.35 1 3

CV-RAIL-EQPM Railroad equipment (e.g., gates, signals) 0 0.35 91 106

CV-RAIL-IDEN Railroad - annotation 0 0.35 6 5

CV-RAIL-TRAK Railroad tracks RAILRD 0.35 2 4
















Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor





Topography













Model File Type: Joint Layout Plan


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information











Joints

CV-JNTS-CNSL Construction joints - longitudinal 0 0.35 6 5

CV-JNTS-CNST Construction joints - transverse 0 0.35 6 5

CV-JNTS-CNTL Contraction joints - longitudinal 0 0.35 2 4

CV-JNTS-CNTT Contraction joints - transverse 0 0.35 2 4

CV-JNTS-EDGE Thickened edges 0 0.35 4 7

CV-JNTS-EXPN Expansion joints 0 0.35 12 27

CV-JNTS-IDEN Joint annotation 0 0.35 2 4

Pavement


Topography






Model File Type: Airfield Plan


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information











Alignments









Aprons

CV-APRN-CNTR Apron centerlines 7 0.35 1 3

CV-APRN-CNTR-IDEN Apron centerline annotation 0 0.35 2 4

CV-APRN-GRND Grounding points 0 0.35 2 4

CV-APRN-HOLD Holding position markings 0 0.25 1 3

CV-APRN-IDEN Airfield apron - annotation 0 0.35 2 4

CV-APRN-MOOR Mooring points 0 0.35 4 7

CV-APRN-MRKG Apron markings 0 0.50 4 7

CV-APRN-OTLN Airfield apron - outlines 0 0.50 4 7

CV-APRN-SECU Security zone markings 0 0.25 1 3






Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

CV-APRN-SHLD Shoulders with annotation 0 0.35 2 4

CV-APRN-SHLD-MRKG Shoulder stripes 0 0.35 2 4

Heliports

CV-HELI-BLST Blast pad and stopway markings 0 0.35 1 3

CV-HELI-CNTR Centerline markings 0 0.35 1 3

CV-HELI-DISP Displaced threshold markings 0 0.35 1 3

CV-HELI-DIST Fixed distance markings 0 0.35 1 3

CV-HELI-IDEN Heliport numbers and letters 0 0.35 2 4

CV-HELI-SHLD Shoulder markings 0 0.35 6 5

CV-HELI-SIDE Side stripes 0 0.50 4 7

CV-HELI-TDZM Touchdown zone markers 0 0.35 6 5

CV-HELI-THRS Threshold markers 0 0.35 6 5

Obstructions

CV-OBST-AIRS Airspace obstructions 0 0.35 3 2

CV-OBST-AIRS-IDEN Obstruction annotation 0 0.35 2 4

Overrun Areas

CV-OVRN-CNTR Centerlines 7 0.25 1 3

CV-OVRN-CNTR-IDEN Centerline annotation 0 0.35 2 4

CV-OVRN-IDEN Airfield overrun area - annotation 0 0.35 2 4

CV-OVRN-OTLN Airfield overrun area - outlines 0 0.35 4 7

CV-OVRN-SHLD-MRKG Shoulder markings 0 0.35 4 7

Pads (Arm/Disarm/Calibration, etc.)

CV-PADS-CNTR Centerlines 7 0.25 1 3

CV-PADS-CNTR-IDEN Centerline annotation 0 0.35 2 4

CV-PADS-IDEN Pads - annotation 0 0.35 2 4

CV-PADS-OTLN Pad - outlines 0 0.35 4 7

CV-PADS-SHLD Shoulders with annotation 0 0.25 2 4

Pavement







Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor




Runways

CV-RUNW-BLST Blast pad and stopway markings 0 0.35 1 3

CV-RUNW-CNTR Centerlines 7 0.25 1 3

CV-RUNW-CNTR-MRKG Centerline markings 0 0.35 1 3

CV-RUNW-DISP Displaced threshold markings 0 0.35 1 3

CV-RUNW-DIST Fixed distance markings 0 0.35 1 3

CV-RUNW-EDGE Airfield runway edges 0 0.35 6 5

CV-RUNW-IDEN Airfield runway annotation 0 0.35 2 4

CV-RUNW-SHLD Shoulder markings 0 0.35 4 7

CV-RUNW-SIDE Side stripes 0 0.35 4 7

CV-RUNW-TDZM Touchdown zone markers 0 0.35 6 5

CV-RUNW-THRS Threshold markers 0 0.35 6 5

Taxiways

CV-TAXI-CNTR Centerlines 7 0.25 1 3

CV-TAXI-CNTR-IDEN Centerline annotation 0 0.35 2 4

CV-TAXI-CNTR-MRKG Centerline markings 0 0.25 1 3

CV-TAXI-EDGE Edge markings 0 0.35 4 7

CV-TAXI-HOLD Holding lines 0 0.35 2 4

CV-TAXI-IDEN Taxiway - annotation 0 0.35 2 4

CV-TAXI-OTLN Taxiway - outlines 0 0.35 4 7

CV-TAXI-SHLD Shoulders with annotation 0 0.35 2 4

Topography











Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor





Airfield Traffic Areas

CV-TRAF-IDEN Airfield traffic area annotation 0 0.35 2 4

CV-TRAF-TYPA Type A traffic area 4 0.50 4 7

CV-TRAF-TYPB Type B traffic area 6 0.50 4 7

CV-TRAF-TYPC Type C traffic area 10 0.50 4 7




Model File Type: Utilities Plan


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information











Alignments









Domestic Water














Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor













Liquid Fuel


CV-FUEL-BERM Berms for retaining fuel in case of major tank/line rupture 0 0.35 6 5

CV-FUEL-DEFL-PIPE Defueling piping 0 0.35 6 5

CV-FUEL-DEVC Air eliminators, filter strainers, hydrant fill points, line vents, markers, oil/water

separators, reducers, regulators, and valves 0 0.35 6 5

CV-FUEL-FLOW Flow direction arrows 0 0.35 6 5

CV-FUEL-FTTG Caps, crosses, and tees 0 0.35 6 5


CV-FUEL-JBOX Junction boxes, manholes, handholes, test boxes 0 0.35 1 3


CV-FUEL-METR Meters 0 0.35 3 2


CV-FUEL-PITS-IDEN Identifier tags, symbol modifier, and text 0 0.35 3 2

CV-FUEL-PITS-VENT Vent pits 0 0.35 3 2






Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor


CV-FUEL-SERV-PIPE Service piping 0 0.35 6 5

CV-FUEL-STNS-IDEN Identifier tags, symbol modifier, and text 0 0.35 2 4

CV-FUEL-STNS-PUMP Booster pump stations 0 0.35 6 5


CV-FUEL-TRCH Fuel line trench 0 0.35 3 2



CV-INDW-DEVC Grit chambers, meters, flumes, neutralizers, oil/water separators, ejectors,

tanks, and valves 0 0.35 6 5

CV-INDW-FLOW Flow direction arrows 0 0.35 6 5

CV-INDW-FTTG Caps and cleanouts 0 0.35 6 5


CV-INDW-JBOX Junction boxes and manholes 0 0.35 1 3

CV-INDW-LAGN Lagoons 0 0.35 6 5

CV-INDW-LAGN-IDEN Identifier tags, symbol modifier, and text 0 0.35 6 5


CV-INDW-PLNT Treatment plants 0 0.35 6 5

CV-INDW-SERV-PIPE Industrial waste water service piping 0 0.35 1 3

CV-INDW-SIGN Surface markers/signs 0 0.35 1 3

CV-INDW-STNS-IDEN Identifier tags, symbol modifier, and text 0 0.35 2 4

CV-INDW-STNS-LIFT Lift stations 0 0.35 6 5

Irrigation




CV-IRRG-WELL Irrigation wells 0 0.25 3 2

Natural Gas







Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

CV-NGAS-DEVC Hydrant fill points, lights, vents, markers, rectifiers, reducers, regulators,

sources, drip pots, taps, and valves 0 0.35 6 5

CV-NGAS-DEVCV-IDEN Identifier tags, symbol modifier, and text 0 0.35 6 5

CV-NGAS-FLOW Flow direction arrows 0 0.35 6 5

CV-NGAS-FTTG Caps, crosses, and tees 0 0.35 6 5



CV-NGAS-METR Meters 0 0.35 3 2

CV-NGAS-PITS-IDEN Identifier tags, symbol modifier, and text 0 0.35 1 3

CV-NGAS-PITS-VENT Vent pits 0 0.35 3 2


CV-NGAS-SERV-PIPE Service piping 0 0.35 1 3

CV-NGAS-SIGN Surface markers/signs 0 0.35 1 3

CV-NGAS-STNS-IDEN Identifier tags, symbol modifier, and text 0 0.35 2 4

CV-NGAS-STNS-PUMP Compressor stations 0 0.35 6 5

CV-NGAS-STNS-REDC Reducing stations 0 0.35 6 5

CV-NGAS-TANK Tanks 0 0.25 3 2

Sanitary Sewer


CV-SSWR-DEVC Grease traps, grit chambers, flumes, neutralizers, oil/water separators,

ejectors, and valves 0 0.35 6 5


CV-SSWR-FILT Filtration beds 0 0.35 3 2

CV-SSWR-FILT-IDEN Identifier tags, symbol modifier, and text 0 0.35 3 2

CV-SSWR-FLOW Flow direction arrows 0 0.35 6 5








Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor


CV-SSWR-JBOX-IDEN Identifier tags, symbol modifier, and text 0 0.35 1 3

CV-SSWR-LAGN Lagoons 0 0.35 3 2

CV-SSWR-LEAC Leach field 0 0.35 3 2


CV-SSWR-NITF Nitrification drain fields 0 0.35 6 5

CV-SSWR-PLNT Treatment plants 0 0.35 6 5

CV-SSWR-SERV-PIPE Sanitary sewer service piping 0 0.35 1 3

CV-SSWR-SIGN Surface markers/signs 0 0.35 1 3

CV-SSWR-STNS-IDEN Identifier tags, symbol modifier, and text 0 0.35 2 4

CV-SSWR-STNS-PUMP Booster pump stations 0 0.35 6 5


Storm Sewer


CV-STRM-AFFF AFFF lagoon/detention pond 0 0.35 3 2

CV-STRM-CHUT Chutes and concrete erosion control structures 0 0.35 1 3



CV-STRM-FLOW Flow direction arrows 0 0.35 6 5

CV-STRM-FMON Flow monitoring station 0 0.35 6 5




CV-STRM-INLT Inlets (curb, surface, and catch basins) 0 0.35 3 2

CV-STRM-LAGN Lagoons, ponds, watersheds, and basins 0 0.35 3 2

CV-STRM-MAIN-PIPE Storm sewer piping STRAF STRAF 0.35 6 5


CV-STRM-ROOF Roof drain line 0 0.35 3 2

CV-STRM-SERV-PIPE Storm sewer service piping 0 0.35 1 3

CV-STRM-SIGN Surface markers/signs 0 0.35 1 3






Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

CV-STRM-STNS-IDEN Identifier tags, symbol modifier, and text 0 0.35 2 4


CV-STRM-SUBS-PIPE Subsurface drain piping 0 0.35 3 2

Topography





Model File Type: Profiles


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information











Alignments







Aprons






Bridges

CV-BRDG-CHRD-LOW~ Low chord 0 0.50 4 7



Channels






Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

CV-CHAN-BANK-TOP~ Channel/canal top of bank 0 0.35 2 4



CV-CHAN-TOE~ Channel/canal toe 3 0.50 5 1

Domestic Water






Floodwalls








Liquid Fuel







Grade Linework

CV-GRAD-BNCH Bench Cut 0 0.35 6 5


CV-GRAD-EXCV Excavation grade 0 0.50 4 7






Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor











Grid Lines

CV-GRID-FRAM Frame 0 0.50 4 7

CV-GRID-MAJR Major grid lines 1 0.35 8 9

CV-GRID-MINR Minor grid lines 1 0.18 8 9

CV-GRID-TEXT Border text, annotation 1 0.35 2 4

Heliports







Irrigation



Levees

CV-LEVE-BANK-TOP~ Levee top of bank 0 0.35 2 4









Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

CV-LEVE-TOE~ Levee toe 2 0.35 20 6

Natural Gas





Overrun Areas



Pads (Arm/Disarm. Calibration, etc.)



Parking Lots



Pavement


Railroads



Rivers














Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor







Runways



Site Features


Sanitary Sewer























Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor




Storm Sewer





















Taxiways






Model File Type: Elevations


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information











Irrigation



Rivers






Elevations









Model File Type: X-Sections


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information











Aprons






Bridges

CV-BRDG-CHRD-LOW~ Low chord 0 0.50 4 7



Channels

CV-CHAN-BANK-TOP~ Channel/canal top of bank 0 0.35 2 4



CV-CHAN-TOE~ Channel/canal toe 3 0.50 5 1

Domestic Water







Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor





Floodwalls










Liquid Fuel







Grade Linework

CV-GRAD-ALOW Allowable over depth 0 0.35 6 5

CV-GRAD-BNCH Bench cut 0 0.35 6 5


CV-GRAD-EXCV Excavation grade 0 0.50 4 7










Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor





CV-GRAD-REQD Required depth 0 0.35 6 5



Grid Lines

CV-GRID-FRAM Frame 0 0.50 4 7

CV-GRID-MAJR Major grid lines 1 0.35 8 9

CV-GRID-MINR Minor grid lines 1 0.18 8 9

CV-GRID-TEXT Border text, annotation 1 0.35 2 4

Heliports







Irrigation



Levees

CV-LEVE-BANK-TOP~ Levee top of bank 0 0.35 2 4












Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor





CV-LEVE-TOE~ Levee toe 2 0.35 20 6

CV-LEVE-TOE~-IDEN Levee toe annotation 0 0.25 20 6

Natural Gas





Overrun Areas



Pads (Arm/Disarm/Calibration, etc.)



Parking Lots



Property








Pavement






Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor


Railroads



Rivers
















Runways



Site Features


Sanitary Sewer



CV-SSWR-DEVC-IDEN Identifier tags, symbol modifier, and text 0 0.25 6 5






Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor


















Storm Sewer


















Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor









Taxiways



Sections

CV-SECT-IDEN Component identification numbers 0 0.35 2 4

CV-SECT-MBND Material beyond section cut 0 0.18 5 1

CV-SECT-MCUT Cuts through road surfaces, buildings, structures, fence lines, etc. V V V V

CV-SECT-PATT Textures and hatch patterns 0 0.18 8 9






Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information











Irrigation





Details

CV-DETL-GRPH Graphics, gridlines, non-text items V V V V

CV-DETL-INPD Inch-pound-specific dimensions and notes 0 0.35 1 3

CV-DETL-METR MetriCV-specific dimensions and notes 0 0.35 3 2



4.7 Fueling Systems

TABLE I-4-25 Discipline: Fueling Systems

Model File Type: Subsurface Investigation Plan


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information

FU-ANNO-DIMS Witness/extension lines, dimension terminators, dimension tex 0 V V V

FU-ANNO-KEYN Reference keynotes with associated leaders 0 V V V

FU-ANNO-NOTE General notes and general remarks 0 0.35 2 4

FU-ANNO-NPLT Non-plotting graphic information 0 0.18 5 1

FU-ANNO-PATT Patterning, poche, shading, and hatching V 0.18 8 9

FU-ANNO-RDME Read-me information 0 0.18 5 1

FU-ANNO-REFR Reference files (AutoCAD users only) NA NA NA NA

FU-ANNO-SYMB Miscellaneous symbols V V 6 5

FU-ANNO-TEXT Miscellaneous text and callouts with associated leaders 0 V V V

Existing Conditions

FU-EXST-BLDG Existing building 0 0.25 1 3

FU-EXST-COND Existing conditions 0 0.25 1 3

Geophysical Borings

FU-BORE-CONE Cone penetrometer test location 0 0.35 162 33

FU-BORE-HOLE Geophysical boring locations 0 0.35 162 33

FU-BORE-IDEN Geophysical location identification 0 0.35 2 4

FU-BORE-LINE Geophysical transect lines 0 0.50 4 7

FU-BORE-PUSH Direct push test location 0 0.35 162 33

FU-BORE-STRK Geophysical strike line 0 0.35 162 33

Consolidation Curve

FU-CONS-DATA Consolidation curve data 0 0.25 6 5

FU-CONS-DATA-TEXT Consolidation curve data text 0 0.25 6 5

FU-CONS-FRAM Consolidation curve frame 0 0.50 4 7

FU-CONS-GRID Consolidation curve grid 0 0.25 2 4

FU-CONS-GRID-TEXT Consolidation curve grid text 0 0.25 2 4

Water Content

FU-H2OC-ATTB-DATA Water content Atterberg limits 0 0.25 3 2






Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

FU-H2OC-ATTB-TEXT Water content Atterberg limits text 0 0.25 3 2

FU-H2OC-GRID-MAJR Water content major grid 0 0.25 1 3

FU-H2OC-GRID-MINR Water content minor grid 1 0.18 8 9

FU-H2OC-GRID-TEXT Water content grid text 0 0.25 2 4

FU-H2OC-MOIS-DATA Water content moisture content points and lines 0 0.25 6 5

FU-H2OC-MOIS-TEXT Water content moisture content text 0 0.25 6 5

Normal Stress

FU-NORM-DATA Normal stress data 0 0.25 6 5

FU-NORM-DATA-TEXT Normal stress data text 0 0.25 6 5

FU-NORM-GRID-MAJR Normal stress major grid 0 0.25 1 3

FU-NORM-GRID-MINR Normal stress minor grid 1 0.18 8 9

FU-NORM-GRID-TEXT Normal stress grid text 0 0.25 2 4

Plasticity Chart

FU-PLAS-DATA Plasticity chart data 0 0.25 6 5

FU-PLAS-DATA-TEXT Plasticity chart data text 0 0.25 4 7

FU-PLAS-FRAM Plasticity chart frame 0 0.50 5 7

FU-PLAS-GRID Plasticity chart grid 0 V V V

FU-PLAS-GRID-TEXT Plasticity chart grid text 0 V V V

Sample Locations

FU-SAMP-AUGR Auger sample location 0 0.35 17 67

FU-SAMP-CORE Core sample location 0 0.35 17 67

FU-SAMP-DRVE Drive sample (shelby split spoon) location 0 0.35 17 67

FU-SAMP-GRAB Grab sample location 0 0.35 17 67

FU-SAMP-IDEN Sample location identification 0 0.35 2 4

FU-SAMP-PERC Percolation test hole 0 0.50 83 42

FU-SAMP-PITS Test pit sample location 0 0.50 83 42

FU-SAMP-VERT Vertical core hole location 0 0.35 122 23

FU-SAMP-WASH Wash bored hole location 0 0.35 122 23

Shear Strength vs. Normal Stress

FU-SSNS-DATA Shear strength vs. normal stress data 0 0.25 6 5






Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

FU-SSNS-DATA-TEXT Shear strength vs. normal stress data text 0 0.25 6 5

FU-SSNS-FRAM Shear strength vs. normal stress frame 0 0.50 4 7

FU-SSNS-GRID Shear strength vs. normal stress grid 0 0.25 1 3

FU-SSNS-GRID-TEXT Shear strength vs. normal stress grid text 0 V 2 4

Shear Strength

FU-SSTR-1TST-DATA Shear strength 1 Point Q test data 0 0.25 4 7

FU-SSTR-1TST-TEXT Shear strength 1 Point Q test text 0 0.25 4 7

FU-SSTR-GRID-MAJR Shear strength major grid 0 0.25 1 3

FU-SSTR-GRID-MINR Shear strength minor grid

1 0.18 8 9

FU-SSTR-GRID-TEXT Shear strength grid text 0 0.25 2 4

FU-SSTR-QTST-DATA Shear strength Q test data 0 0.25 6 5

FU-SSTR-QTST-TEXT Shear strength Q test text 0 0.25 6 5

FU-SSTR-RTST-DATA Shear strength R test data 0 0.25 2 4

FU-SSTR-RTST-TEXT Shear strength R test text 0 0.25 2 4

FU-SSTR-STST-DATA Shear strength S test data 0 0.25 5 1

FU-SSTR-STST-TEXT Shear strength S test text 0 0.25 5 1

FU-SSTR-UTST-DATA Shear strength UCT test data 0 0.25 3 2

FU-SSTR-UTST-TEXT Shear strength UCT test text 0 0.25 3 2

FU-SSTR-VTST-DATA Shear strength Vane shear test data 0 0.25 7 0

FU-SSTR-VTST-TEXT Shear strength Vane shear test text 0 0.25 7 0

Tabular Test

FU-TABT-DATA Tabular test data 0 0.25 6 5

FU-TABT-DATA-TEXT Tabular test data text 0 0.25 6 5

FU-TABT-FRAM Tabular test data frame 0 0.50 4 7

FU-TABT-GRID Tabular test data grid 0 0.25 1 3

FU-TABT-GRID-TEXT Tabular test data grid text 0 V 2 4

Wells

FU-WELL-ASR ASR wells 0 0.35 82 18

FU-WELL-MONT Monitoring wells 0 0.35 82 18






Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

FU-WELL-PIZO Piezometers 0 0.35 82 18

Wet Density

FU-WETD-DATA Wet density data 0 0.25 6 5

FU-WETD-DATA-TEXT Wet density data text 0 0.25 6 5

FU-WETD-GRID-MAJR Wet density major grid 0 0.25 1 3

FU-WETD-GRID-MINR Wet density minor grid 1 0.18 8 9

FU-WETD-GRID-TEXT Wet density grid text 0 0.25 2 4



4.8 Landscape

TABLE I-4-26 Discipline: Landscape



Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information

LA-ANNO-DIMS Witness extension lines, dimensions arrowheads and text 0 V V V

LA-ANNO-KEYN Keynote with associated leaderlines and arrowheads 0 V V V

LA-ANNO-NPLT Construction lines, reference targets, area calculations V 0 5 1

LA-ANNO-PATT Miscellaneous patterning 0 0 8 9

LA-ANNO-NOTE General note and general remarks 0 2 2 4

LA-ANNO-SYMB Reference bubbles, matchlines, breaklines V 2 6 5

LA-ANNO-TEXT Detail title text, leaderlines, arrowheads, notes 0 V V V

LA-STAT-DEMO Demolition 2 2 6 5

LA-STAT-EXST Existing to remain 0 1 3 2

LA-STAT-MOVE Items to be moved 5 2 6 5

LA-STAT-NICN Not in contract 3 0 8 9

LA-STAT-PHS# Phase numbers (# = 1-9) 0 2 2 4

LA-STAT-RELO Relocated items 2 0 5 1

LA-STAT-TEMP Temporary work 4 3 4 7

LA-DEMO-HAZW Hazardous waste 0 2 6 5




Model File Type: Landscape Plan


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information

LA-ANNO-DIMS Witness/extension lines, dimension terminators, dimension text 0 V V V

LA-ANNO-KEYN Reference keynotes with associated leaders 0 V V V

LA-ANNO-NOTE General notes and general remarks 0 0.35 2 4

LA-ANNO-NPLT Non-plotting graphic information 0 0.18 5 1

LA-ANNO-PATT Patterning, poche, shading, and hatching V 0.18 8 9

LA-ANNO-RDME Read-me information 0 0.18 5 1

LA-ANNO-REFR Reference files (AutoCAD users only) NA NA NA NA

LA-ANNO-SYMB Miscellaneous symbols V V 6 5

LA-ANNO-TEXT Miscellaneous text and callouts with associated leaders 0 V V V

Plant and Landscape Material

LA-PLNT-BEDS Planting beds (perennial and annual beds) 0 0.35 6 5

LA-PLNT-BUSH Bushes and shrubs (e.g., evergreen, deciduous, etc.) 0 0.50 83 42

LA-PLNT-BUSH-LINE Bush and shrub line 0 0.50 83 42

LA-PLNT-CTNR Containers or planters 0 0.25 1 3

LA-PLNT-GRND Groundcover and vines 0 0.35 82 18

LA-PLNT-IDEN Annotation 0 0.35 6 5

LA-PLNT-MLCH Mulches - organic and inorganic 0 0.25 3 2

LA-PLNT-PLTS Planting plants (e.g., ornamental annuals and perennials 0 0.50 83 42

LA-PLNT-SHAD Shadow areas 0 0.18 5 1

LA-PLNT-SPRG Sprigs 0 0.25 3 2

LA-PLNT-TREE Trees (e.g., evergreen, deciduous, etc.)

0 0.50 83 42

LA-PLNT-TREE-LINE Tree line TREEL 0.50 83 42

LA-PLNT-TURF Lawn areas (turfing limits) 0 0.50 23 46

Site Improvements

LA-SITE-BRDG Bridges (pedestrian) 0 0.35 22 22

LA-SITE-DECK Decks 0 0.35 232 107

LA-SITE-FENC Fencing FENCE 0.35 2 4

LA-SITE-FURN Furnishings 0 0.50 4 7




Model File Type: Landscape Plan


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

LA-SITE-IDEN Annotation 0 0.35 6 5

LA-SITE-PLAY Play structures 0 0.35 2 4

LA-SITE-POOL Pools and spas 0 0.35 162 33

LA-SITE-ROCK Boulders and cobble 0 0.25 1 3

LA-SITE-RTWL Retaining walls 0 0.50 4 7

LA-SITE-SPRT Sports fields 0 0.35 2 4

LA-SITE-WALK Walks and steps 0 V V V




Model File Type: Irrigation Plan


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information

LA-ANNO-DIMS Witness/extension lines, dimension terminators, dimension text 0 V V V









Irrigation System

LA-IRRG-COVR Irrigation coverage, spray distribution patterns 0 0.18 5 1

LA-IRRG-EQPM Equipment (e.g., controllers, valves, RPBPs, etc.) 0 0.35 6 5

LA-IRRG-HEAD Irrigation heads, bubblers, and drip irrigation emitters 0 0.25 1 3

LA-IRRG-IDEN Annotation 0 0.35 2 4

LA-IRRG-PIPE Piping LAWNSP 0.35 6 5

LA-IRRG-SPKL Sprinklers 0 0.35 6 5






Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information

LA-ANNO-DIMS Witness/extension lines, dimension terminators, dimension tex 0 V V V









Detail Information

LA-DETLA-GRPH Graphics, gridlines, non-text items V V V V

LA-DETLA-INPD Inch-pound specific dimensions and notes V V V V

LA-DETLA-METR Metric specific dimensions and notes V V V V



4.9 Structural Buildings

TABLE I-4-30 Discipline: Structural Buildings



Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information

ST-ANNO-DIMS Witness extension lines, dimensions arrowheads and text 0 V V V

ST-ANNO-KEYN Keynote with associated leaderlines and arrowheads 0 V V V

ST-ANNO-NPLT Construction lines, reference targets, area calculations V 0 5 1

ST-ANNO-PATT Miscellaneous patterning 0 0 8 9

ST-ANNO-NOTE General note and general remarks 0 2 2 4

ST-ANNO-SYMB Reference bubbles, matchlines, breaklines V 2 6 5

ST-ANNO-TEXT Detail title text, leaderlines, arrowheads, notes 0 V V V

ST-STAT-DEMO Demolition 2 2 6 5

ST-STAT-EXST Existing to remain 0 1 3 2

ST-STAT-MOVE Items to be moved 5 2 6 5

ST-STAT-NICN Not in contract 3 0 8 9

ST-STAT-PHS# Phase numbers (# = 1-9) 0 2 2 4

ST-STAT-RELO Relocated items 2 0 5 1

ST-STAT-TEMP Temporary work 4 3 4 7

ST-DEMO-HAZW Hazardous waste 0 2 6 5




Model File Type: Foundation Plan


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information

ST-ANNO-DIMS Witness/extension lines, dimension terminators, dimension text 0 V V V

ST-ANNO-KEYN Reference keynotes with associated leaders 0 V V V

ST-ANNO-NOTE General notes and general remarks 0 0.35 2 4

ST-ANNO-NPLT Non-plotting graphic information 0 0.18 5 1

ST-ANNO-PATT Patterning, poche, shading, and hatching 0 0.18 8 9

ST-ANNO-RDME Read-me information 0 0.18 5 1

ST-ANNO-REFR Reference files (AutoCAD users only) NA NA NA NA

ST-ANNO-SYMB Miscellaneous symbols V V 6 5

ST-ANNO-TEXT Miscellaneous text and callouts with associated leaders 0 V V v

Access

ST-ACCS-GLRY Galleries, crossovers, trenches, etc 0 0.35 30 86

ST-ACCS-HTCH Hatches 0 0.25 32 102

ST-ACCS-LADD Ladders and ladder safety devices 0 0.35 162 33

ST-ACCS-STRS Stairs 0 0.35 133 111

ST-ACCS-TUNL Tunnels 0 0.35 42 182

Equipment Pads and Foundations

ST-PADS-EQPM Equipment pads 0 0.35 21 30

Erosion Control

ST-EROS-BARR Vapor/capillary water barriers 0 0.25 233 115

Fasteners & Connections

ST-FSTN-ABLT Anchor bolts 0 0.25 30 86

Foundations

ST-FNDN-ANCH Anchor piles, blocks, strands, deadmen, soil/rock anchors 0 0.35 42 182

ST-FNDN-CNTR Foundation centerlines 7 0.18 44 198

ST-FNDN-DRAN Foundation drainage features and objects 0 0.25 43 206

ST-FNDN-FTNG Footings 0 0.35 42 182

ST-FNDN-FTNG-RBAR Footing rebar 0 0.70 5 1

ST-FNDN-GRBM Grade beams 0 0.50 52 36

ST-FNDN-PEDS Foundation pedestals/pads 0 0.35 41 190






Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

ST-FNDN-PIER Piers, drilled shafts, caissons 0 0.50 72 196

ST-FNDN-PILE Piles 0 0.35 40 166

ST-FNDN-RIBS Ribbed mat foundation 0 0.35 52 36

ST-FNDN-TRMT Foundation treatment (grouting) 0 0.35 51 28

ST-FNDN-TUNL Service tunnel/duct banks 0 0.35 42 182

Grade Lines

ST-GRLN-SURF-E Existing ground 3 0.25 31 110

ST-GRLN-SURF-N Finished grade 0 0.35 32 102

ST-WATR-SURF Water surface 0 0.25 161 25

Joints

ST-JNTST-CNTJ Construction/lift joints 0 0.25 122 23

ST-JNTST-CTLJ Control/contraction joints (saw cut) 0 0.25 122 23

ST-JNTST-EXPJ Expansion joints, joint materials (e.g., felt) 0 0.25 124 39

ST-JNTST-WTRS Waterstops 0 0.25 221 189

Fabrications (metal or other specialty)

ST-FABR-EMBD Embedded metals (framing around openings) 0 0.35 183 201

ST-FABR-PLAT Plates 0 0.35 142 183

Reinforcement

ST-REIN-RBAR Steel reinforcing, welded wire fabric 0 0.70 5 1

Reference Outlines

ST-OTLN-BLDG Building outline 6 0.25 5 1

ST-OTLN-FLOR Floor outline 6 0.25 5 1

ST-OTLN-OPNG Openings 6 0.25 5 1

ST-OTLN-ROOF Roof 6 0.25 5 1

ST-OTLN-STRC Misc. structures 6 0.25 5 1

Slabs

ST-SLAB-EDGE Edge of slab 0 0.35 41 190

ST-SLAB-RBAR Slab rebar 0 0.70 5 1

ST-SLAB-SECD Second pour, slab cap 0 0.35 41 190

ST-SLAB-SILL Sill 0 0.35 41 190






Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

Walls

ST-WALL-LOAD Load bearing walls 0 0.35 3 2

ST-WALL-NONL Non-load bearing walls 0 0.35 72 196

ST-WALL-PCST Pre-cast concrete walls 0 0.35 126 55

ST-WALL-SHEA Shear walls 0 0.35 101 186

ST-WALL-STUD Stud walls 0 0.35 421 182




Model File Type: Framing Plan


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information










Access

ST-ACCS-EVTR Elevators 0 0.35 132 103

ST-ACCS-LADD Ladders and ladder safety devices 0 0.35 162 33

ST-ACCS-STRS-FRMG Stair framing 0 0.35 135 127

Beams

ST-BEAM-CNTR Beam centerlines 7 0.18 214 117

ST-BEAM-PRIM Continuous beam or primary beam of two-way beam system 0 0.50 211 109

ST-BEAM-RBAR Beam rebar 0 0.70 5 1

ST-BEAM-SECD Girders or secondary beams of two-way beam system 0 0.35 212 101

Bracing

ST-BRAC-DIAG Diagonal bracing 0 0.35 161 25

ST-BRAC-HORZ Horizontal bracing 0 0.35 161 25

ST-BRAC-VERT Vertical bracing 0 0.35 144 199

Decking

ST-DECK-FLOR Floor deck 0 0.25 101 186

ST-DECK-ROOF Roof deck 0 0.25 62 116


ST-FSTN-ABLT Anchor bolts 0 0.25 30 86

ST-FSTN-MISC Fasteners and connections (non-specific) 0 0.25 13 35





Gates

ST-GATE-AXIS Gate axis and centerlines 7 0.18 214 117

Joints

ST-JNTST-CNTJ Construction/lift joints 0 0.25 122 23

ST-JNTST-CTLJ Control/contraction joints (saw cut) 0 0.25 122 23

ST-JNTST-EXPJ Expansion joints, joint materials (e.g., felt) 0 0.25 124 39

ST-JNTST-STUC Stucco joints 0 0.25 111 246

Joists

ST-JOIST-BRDG Bridging 0 0.35 82 18

ST-JOIST-GIRD Joist girders 0 0.50 122 23

ST-JOIST-PERI Perimeter channel or rim joist 0 0.35 142 183

ST-JOIST-PRIM Primary joists 0 0.35 132 103

ST-JOIST-SECD Secondary joists 0 0.35 134 119

ST-JOIST-TRIM Partial length or trimmer floor joist 0 0.35 134 119


ST-FABR-EMBD Embedded metals (framing around openings) 0 0.35 183 201

ST-FABR-PLAT Plates 0 0.35 142 183

Platforms

ST-PLAT-GRTG Platform grating (add a second minor group to indicate platform # or elev.) 0 0.25 121 15

Reinforcement


Reference Outlines





Signs

ST-SIGN-EXTN Extrusions 0 0.35 212 101

ST-SIGN-FRMG Framing & connections 0 0.35 3 2

ST-SIGN-PANL Sign panels 0 0.35 232 107

ST-SIGN-SPRT Supports 0 0.35 5 1

ST-SIGN-TEXT Signage text 0 0.35 222 181

Stiffeners

ST-STIF-LONG Stiffeners - longitudinal 0 0.35 3 2





ST-STIF-TRAN Stiffeners - transverse 0 0.35 3 2

Trusses

ST-TRUST-PRIM Primary trusses 0 0.50 4 7

ST-TRUST-SECD Secondary trusses 0 0.35 6 5

Walls

ST-WALL-FULL Wall going to the top of the structure 0 0.35 3 2

ST-WALL-LOAD Load bearing walls 0 0.35 3 2

ST-WALL-NONL Non-load bearing walls 0 0.35 72 196

ST-WALL-PCST Pre-cast concrete walls 0 0.35 126 55

ST-WALL-PRHT Wall that does not reach to the top of the structure 0 0.35 72 196

ST-WALL-SHEA Shear walls 0 0.35 101 186

ST-WALL-STUD Stud walls 0 0.35 421 182




Model File Type: Column Plan


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information










Columns

ST-COLS-CNTR Column centerlines/working lines 7 0.18 40 166

ST-COLS-POST Short columns 0 0.35 87 74

ST-COLS-PRIM Primary columns 0 0.35 3 2

ST-COLS-RBAR Column rebar 0 0.70 5 1

ST-COLS-SECD Secondary columns 0 0.35 84 34

Grids

ST-GRID-HORZ Grid lines (horizontal) 7 0.18 6 5

ST-GRID-HORZ-IDEN Column I.D. tags (horizontal) 0 0.25 6 5

ST-GRID-VERT Grid lines (vertical) 7 0.18 6 5

ST-GRID-VERT-IDEN Column I.D. tags (vertical) 0 0.25 6 5

Reinforcement


Reference Outlines










Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information



ST-ANNO-NPLT Non-plotting graphic information V 0.18 5 1

ST-ANNO-PATT Miscellaneous patterning and hatching 0 0.18 8 9


ST-ANNO-SYMB Miscellaneous symbols V 0.35 6 5

ST-ANNO-TEXT Miscellaneous text and callouts with associated leaders 0 V V V

ST-ANNO-REFR Reference files (AutoCAD users only, refer to Chapter 4) NA NA NA NA

Beams

ST-BEAM-CNTR Beam centerlines 7 0.18 5 1

ST-BEAM-PRIM Primary beams/girders outlines 0,2 0.50 4 7

ST-BEAM-SECD Secondary beams/girders outlines 0,2 0.35 6 5

Joints

ST-JOIN-CNST Construction joints 0 0.25 3 2

ST-JOIN-CTRL Control/expansion joints 0 0.25 1 3

Miscellaneous Supports

ST-SPPT-MISC Miscellaneous fasteners, anchor bolts, supports 0,2 0.25 3 2

ST-SPPT-SHPS Miscellaneous shapes, plates 0,2 0.25 3 2

Walls

ST-WALL-OTLN Wall outline 0,2 0.35 2 4

ST-WALL-VBAR Vertical/primary reinforcement 0,2 0.50 4 7

ST-WALL-HBAR Horizontal/secondary reinforcement 0,2 0.50 4 7

ST-WALL-OPEN Openings and penetrations 0,2 0.25 1 3

Demolition (used only in creating Existing/Demolition model files)

ST-STAT-DEMO-PHS1

Demolition-phase 1 0 0.50 203 45

ST-STAT-DEMO-PHS2


ST-STAT-DEMO-PHS3






Note: V=Varies, NA=Not Applicable






Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information



ST-ANNO-NPLT Non-plotting graphic information V 0.18 B/5 B/1

ST-ANNO-PATT Miscellaneous patterning and hatching 0 0.18 Gr/8 Gr/9

ST-ANNO-NOTE General notes and general remarks 0 0.35 Y/2 Y/4

ST-ANNO-SYMB Miscellaneous symbols V 0.35 M/6 M/5



Section Information

ST-SECT-GENF General features (miscellaneous items) 0,2 0.35 M/6 M/5

ST-SECT-CMUW CMU outline (no patterning) 0,2 0.35 Y/2 Y/4

ST-SECT-CNTR Centerlines 7 0.18 B/5 B/1

ST-SECT-PRIM Primary beams. girders outlines 0,2 0.50 C/4 C/7

ST-SECT-CONC Concrete outline (no patterning) 0,2 0.35 M/6 M/5

ST-SECT-WOOD Wood outline (no patterning) 0,2 0.35 Y/2 Y/4

ST-SECT-JOIN Joint materials (e.g. felt), vapor barrier, other 0,2 0.25 R/1 R/3

ST-SECT-STLS Wide flange shapes, plates, open web joints, decking 0,2 0.25 G/3 G/2

ST-SECT-MISC Miscellaneous fasteners, anchor bolts, supports 0,2 0.25 G/3 G/2

ST-SECT-SHPS Miscellaneous shapes, plates 0,2 0.25 G/3 G/2

ST-SECT-RBAR Rebar, welded wire mesh 0,2,WWFBRC

0.70 W/7 W/0

ST-SECT-FNGR Finished grade O 0.35 Y/2 Y/4







Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information

ST-ANNO-DIMS Witness/extension lines, dimension terminators, dimension text, welding symbols

0 V V V


ST-ANNO-NPLT Non-plotting graphic information V 0.18 B/5 B/1

ST-ANNO-PATT Miscellaneous patterning and hatching 0 0.18 Gr/8 Gr/9

ST-ANNO-NOTE General notes and general remarks 0 0.35 Y/2 Y/4

ST-ANNO-SYMB Miscellaneous symbols V 0.35 M/6 M/5



Detail Information

ST-DETL-GRPH Graphics, gridlines, non-text items V V V V

ST-DETL-METR Metric-specific dimensions and notes 0 0.35 Y/2 Y/4

ST-DETL-INPD Inch-pound-specific dimensions and notes 0 0.35 Y/2 Y/4

Demolition

ST-STAT-DEMO-PHS1


ST-STAT-DEMO-PHS2


ST-STAT-DEMO-PHS3





4.10 Structural Civil

TABLE I-4-37 Discipline: Structural Civil

Model File Type: Substructure


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information

SC-ANNO-DIMS Witness/extension lines, dimension terminators, dimension text 0 V V V

SC-ANNO-KEYN Reference keynotes with associated leaders 0 V V V

SC-ANNO-NOTE General notes and general remarks 0 0.35 2 4

SC-ANNO-NPLT Non-plotting graphic information 0 0.18 5 1

SC-ANNO-PATT Patterning, poche, shading, and hatching 0 0.18 8 9

SC-ANNO-RDME Read-me information 0 0.18 5 1

SC-ANNO-REFR Reference files (AutoCAD users only) NA NA NA NA

SC-ANNO-SYMB Miscellaneous symbols V V 6 5

SC-ANNO-TEXT Miscellaneous text and callouts with associated leaders 0 V V v

Access

SC-ACCS-LADD Ladders and ladder safety devices 0 0.35 162 33

SC-ACCS-MHOL Manholes 0 0.35 83 42

SC-ACCS-MISC Miscellaneous access 0 0.35 83 42

SC-ACCS-STRS Stairs 0 0.35 133 111

SC-ACCS-STRS-FRMG Stair framing 0 0.35 135 127

SC-ACCS-TUNL Tunnels 0 0.35 42 182

Bridges

SC-BRDG-ABUT Abutments 0 0.50 83 42

SC-BRDG-ABUT-RBAR Abutment rebar 0 0.70 5 1

SC-BRDG-BEAR Bridge bearing 0 0.35 152 88

SC-BRDG-BEAR-CNTR Bridge bearing centerlines 7 0.18 214 117

SC-BRDG-BENT Bent cap 0 0.35 3 2

SC-BRDG-BENT-CNTR Centerline of bents 7 0.18 214 117

SC-BRDG-BENT-RBAR Bent cap rebar 0 0.70 5 1

SC-BRDG-PIER Piers 0 0.50 83 42






Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

Columns

SC-COLS-CNTR Column centerlines/working lines 7 0.18 40 166

SC-COLS-PRIM Primary columns 0 0.35 3 2

SC-COLS-RBAR Column rebar 0 0.70 5 1

SC-COLS-SECD Secondary columns 0 0.35 84 34


SC-FSTN-ABLT Anchor bolts 0 0.25 30 86

SC-FSTN-MISC Fasteners and connections (non-specific) 0 0.25 13 35

Foundations

SC-FNDN-ANCH Anchor piles, blocks, strands, deadmen, soil/rock anchors 0 0.35 42 182

SC-FNDN-CNTR Foundation centerlines 7 0.18 44 198

SC-FNDN-DRAN Foundation drainage features and objects 0 0.25 43 206

SC-FNDN-FTNG Footings 0 0.35 42 182

SC-FNDN-FTNG-RBAR Footing rebar 0 0.70 5 1

SC-FNDN-PEDS Foundation pedestals/pads 0 0.35 41 190

SC-FNDN-PILE Piles 0 0.35 40 166

SC-FNDN-TRMT Foundation treatment (grouting) 0 0.35 51 28

Grade Lines

SC-GRLN-SURF-E Existing ground 3 0.25 31 110

SC-GRLN-SURF-N Finished grade 0 0.35 32 102

SC-WATR-SURF Water surface 0 0.25 161 25


SC-FABR-EMBD Embedded metals (framing around openings) 0 0.35 183 201

SC-FABR-PLAT Plates 0 0.35 142 183

Platforms

SC-PLAT-FRMG Platform frame/stringers 0 0.35 212 101

SC-PLAT-GRTG Platform grating (add a second minor group to indicate platform # or elev.) 0 0.25 121 15

SC-PLAT-WALK Platform walkway 0 0.35 33 126

Reinforcement






Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

SC-REIN-RBAR Steel reinforcing, welded wire fabric 0 0.70 5 1

Reference Outlines

SC-OTLN-STRC Misc. structures 6 0.25 5 1

Walls

SC-WALL-ABUT Abutments 0 0.35 83 42

SC-WALL-COFF Cutoff wall 0 0.35 30 86

SC-WALL-CURT Curtain/breast wall 0 0.35 72 196

SC-WALL-MSEW Mechanically stabilized earth (MSE) wall 0 0.35 72 196

SC-WALL-RTWL Retaining wall (flood walls, wingwalls, etc.) 0 0.35 72 196

Waterway Specialties

SC-WWAY-DLPH Dolphins (associated with but not part of bridges, locks and guidewalls) 0 0.35 122 23

SC-WWAY-FEND Fenders 0 0.35 75 220

SC-WWAY-MOOR Mooring cells 0 0.35 142 183




Model File Type: Decks


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information










Access

SC-ACCS-HTCH Hatches 0 0.25 32 102


SC-ACCS-MHOL Manholes 0 0.35 83 42

SC-ACCS-MISC Miscellaneous access 0 0.35 83 42

Bridges

SC-BRDG-DRAN Drains 0 0.25 22 22

Decking

SC-DECK-BRDG Bridge deck 0 0.35 22 22

SC-DECK-BRDG-RBAR Bridge deck rebar 0 0.70 5 1




Grids

SC-GRID-HORZ Grid lines (horizontal) 7 0.18 6 5

SC-GRID-HORZ-IDEN Column I.D. tags (horizontal) 0 0.25 6 5

SC-GRID-VERT Grid lines (vertical) 7 0.18 6 5

SC-GRID-VERT-IDEN Column I.D. tags (vertical) 0 0.25 6 5

Joints




Model File Type: Decks


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

SC-JNTST-CNTJ Construction/lift joints 0 0.25 122 23

SC-JNTST-CTLJ Control/contraction joints (saw cut) 0 0.25 122 23

SC-JNTST-EXPJ Expansion joints, joint materials (e.g., felt) 0 0.25 124 39

SC-JNTST-WTRS Waterstops 0 0.25 221 189




Platforms


SC-PLAT-GRTG Platform grating (add a second minor group to indicate platform # or elev.) 0 0.25 121 15


Reinforcement


SC-REIN-TEND-HORZ Horizontal Tendons 0 0.50 181 185

SC-REIN-TEND-VERT Vertical Tendons 0 0.50 181 185

Reference Outlines


Safety Features

SC-SAFE-FENC Fencing rails, fabric, supports, and gates 0 0.25 3 2

SC-SAFE-GRAL Guardrails 0 0.35 62 116

SC-SAFE-HRAL Handrails, railings 0 0.25 3 2

SC-SAFE-PARA Parapet/jersey barrier 0 0.50 3 2

SC-SAFE-PARA-RBAR Parapet/jersey barrier rebar 0 0.70 5 1

SC-SAFE-WATR Waterway safety barriers 0 0.35 3 2

Slabs

SC-SLAB-EDGE Edge of slab 0 0.35 41 190

SC-SLAB-RBAR Slab rebar 0 0.70 5 1

SC-SLAB-SECD Second pour, slab cap 0 0.35 41 190

SC-SLAB-SILL Sill 0 0.35 41 190




Model File Type: Superstructure


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information










Access


SC-ACCS-STRS Stairs 0 0.35 133 111

SC-ACCS-STRS-FRMG Stair framing 0 0.35 135 127

Beams

SC-BEAM-CNTR Beam centerlines 7 0.18 214 117

SC-BEAM-PRIM Continuous beam or primary beam of two-way beam system 0 0.50 211 109

SC-BEAM-RBAR Beam rebar 0 0.70 5 1

SC-BEAM-SECD Girders or secondary beams of two-way beam system 0 0.35 212 101

Bracing

SC-BRAC-DIAG Diagonal bracing 0 0.35 161 25

SC-BRAC-HORZ Horizontal bracing 0 0.35 161 25

SC-BRAC-VERT Vertical bracing 0 0.35 144 199

Bridges

SC-BRDG-BEAR Bridge bearing 0 0.35 152 88

SC-BRDG-BEAR-CNTR Bridge bearing centerlines 7 0.18 214 117

SC-BRDG-CURB Curbs/sidewalks on structure 0 0.35 2 4

SC-BRDG-DIAP Diaphragms 0 0.35 5 1

SC-BRDG-DIAP-RBAR Diaphragm rebar 0 0.70 5 1






Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

SC-BRDG-DRAN Drains 0 0.25 22 22

SC-BRDG-FENC Fencing rails, fabric, supports, and gates 0 0.25 3 2

SC-BRDG-FEND Fenders 0 0.35 75 220

SC-BRDG-GIRD Girders 0 0.35 70 180

SC-BRDG-GIRD-CNTR Girder centerline 7 0.18 214 117

SC-BRDG-HEAD Headers 0 0.35 112 247

SC-BRDG-STRG Stringers 0 0.35 212 101




Gates

SC-GATE-AXIS Gate axis and centerlines 7 0.18 214 117

Grids

SC-GRID-HORZ Grid lines (horizontal) 7 0.18 6 5

SC-GRID-HORZ-IDEN Column I.D. tags (horizontal) 0 0.25 6 5

SC-GRID-VERT Grid lines (vertical) 7 0.18 6 5

SC-GRID-VERT-IDEN Column I.D. tags (vertical) 0 0.25 6 5

Joints

SC-JNTST-CNTJ Construction/lift joints 0 0.25 122 23

SC-JNTST-EXPJ Expansion joints, joint materials (e.g., felt) 0 0.25 124 39



SC-FABR-HOIS Hoist structures 0 0.25 142 183


Platforms



Reinforcement







Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

SC-REIN-TEND-HORZ Horizontal Tendons 0 0.50 181 185

SC-REIN-TEND-VERT Vertical Tendons 0 0.50 181 185

Reference Outlines


Safety Features

SC-SAFE-GRAL Guardrails 0 0.35 62 116

SC-SAFE-HRAL Handrails, railings 0 0.25 3 2

SC-SAFE-PARA Parapet/jersey barrier 0 0.50 3 2

SC-SAFE-PARA-RBAR Parapet/jersey barrier rebar 0 0.70 5 1

Signs

SC-SIGN-PANL Sign panels 0 0.35 232 107

Slabs

SC-SLAB-APPR Approach slab 0 0.35 41 190

SC-SLAB-APPR-RBAR Approach slab rebar 0 0.70 5 1

SC-SLAB-EDGE Edge of slab 0 0.35 41 190

SC-SLAB-RBAR Slab rebar 0 0.70 5 1

SC-SLAB-SECD Second pour, slab cap 0 0.35 41 190

SC-SLAB-SILL Sill 0 0.35 41 190

Stiffeners

SC-STIF-LONG Stiffeners - longitudinal 0 0.35 3 2

SC-STIF-TRAN Stiffeners - transverse 0 0.35 3 2

Trusses

SC-TRUST-PRIM Primary trusses 0 0.50 4 7

SC-TRUST-SECD Secondary trusses 0 0.35 6 5






Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information



SC-ANNO-NPLT Non-plotting graphic information V 0.18 5 1

SC-ANNO-PATT Miscellaneous patterning and hatching 0 0.18 8 9


SC-ANNO-SYMB Miscellaneous symbols V 0.35 6 5

SC-ANNO-TEXT Miscellaneous text and callouts with associated leaders 0 V V V

SC-ANNO-REFR Reference files (AutoCAD users only, refer to Chapter 4) NA NA NA NA

Beams

SC-BEAM-CNTR Beam centerlines 7 0.18 5 1

SC-BEAM-PRIM Primary beams/girders outlines 0,2 0.50 4 7

SC-BEAM-SECD Secondary beams/girders outlines 0,2 0.35 6 5

Joints

SC-JOIN-CNST Construction joints 0 0.25 3 2

SC-JOIN-CTRL Control/expansion joints 0 0.25 1 3

Miscellaneous Supports

SC-SPPT-MISC Miscellaneous fasteners, anchor bolts, supports 0,2 0.25 3 2

SC-SPPT-SHPS Miscellaneous shapes, plates 0,2 0.25 3 2

Walls

SC-WALL-OTLN Wall outline 0,2 0.35 2 4

SC-WALL-VBAR Vertical/primary reinforcement 0,2 0.50 4 7

SC-WALL-HBAR Horizontal/secondary reinforcement 0,2 0.50 4 7

SC-WALL-OPEN Openings and pentrations 0,2 0.25 1 3

Demolition (used only in creating Existing/Demolition model files)

SC-STAT-DEMO-PHS1


SC-STAT-DEMO-PHS2


SC-STAT-DEMO-PHS3







Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor







Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information









Section Information

SC-SECT-GENF General features (miscellaneous items) 0,2 0.35 6 5

SC-SECT-CMUW CMU outline (no patterning) 0,2 0.35 2 4

SC-SECT-CNTR Centerlines 7 0.18 5 1

SC-SECT-PRIM Primary beams. girders outlines 0,2 0.50 4 7

SC-SECT-CONC Concrete outline (no patterning) 0,2 0.35 6 5

SC-SECT-WOOD Wood outline (no patterning) 0,2 0.35 2 4

SC-SECT-JOIN Joint materials (e.g. felt), vapor barrier, other 0,2 0.25 1 3

SC-SECT-STLS Wide flange shapes, plates, open web joints, decking 0,2 0.25 3 2

SC-SECT-MISC Miscellaneous fasteners, anchor bolts, supports 0,2 0.25 3 2

SC-SECT-SHPS Miscellaneous shapes, plates 0,2 0.25 3 2

SC-SECT-RBAR Rebar, welded wire mesh 0,2,WWFBRC

0.70 7 0

SC-SECT-FNGR Finished grade O 0.35 2 4







Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information

SC-ANNO-DIMS Witness/extension lines, dimension terminators, dimension text, welding symbols

0 V V V








Detail Information

SC-DETL-GRPH Graphics, gridlines, non-text items V V V V

SC-DETL-METR Metric-specific dimensions and notes 0 0.35 2 4

SC-DETL-INPD Inch-pound-specific dimensions and notes 0 0.35 2 4

Demolition

SC-STAT-DEMO-PHS1


SC-STAT-DEMO-PHS2


SC-STAT-DEMO-PHS3





4.11 Architectural

TABLE I-4-43 Discipline: Architectural



Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information

AR-ANNO-DIMS Witness extension lines, dimensions arrowheads and text 0 V V V

AR-ANNO-KEYN Keynote with associated leaderlines and arrowheads 0 V V V

AR-ANNO-NPLT Construction lines, reference targets, area calculations V 0 5 1

AR-ANNO-PATT Miscellaneous patterning 0 0 8 9

AR-ANNO-NOTE General note and general remarks 0 2 2 4

AR-ANNO-SYMB Reference bubbles, matchlines, breaklines V 2 6 5

AR-ANNO-TEXT Detail title text, leaderlines, arrowheads, notes 0 V V V

AR-STAT-DEMO Demolition 2 2 6 5

AR-STAT-EXST Existing to remain 0 1 3 2

AR-STAT-MOVE Items to be moved 5 2 6 5

AR-STAT-NICN Not in contract 3 0 8 9

AR-STAT-PHS# Phase numbers (# = 1-9) 0 2 2 4

AR-STAT-RELO Relocated items 2 0 5 1

AR-STAT-TEMP Temporary work 4 3 4 7

AR-DEMO-HAZW Hazardous waste 0 2 6 5




Model File Type: Floor Plan


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information

AR-ANNO-DIMS Witness/extension lines, dimension terminators, dimension text 0 V V V

AR-ANNO-KEYN Reference keynotes with associated leaders 0 V V V

AR-ANNO-MASK Text/shape mask for use with photo backgrounds 0 0.18 113 16

AR-ANNO-NOTE General notes and general remarks 0 0.35 2 4

AR-ANNO-NPLT Non-plotting graphic information 0 0.18 5 1

AR-ANNO-PATT Patterning, poche, shading, and hatching V 0.18 8 9

AR-ANNO-RDME Read-me information 0 0.18 5 1

AR-ANNO-REFR Reference files (AutoCAD users only) NA NA NA NA

AR-ANNO-SYMB Miscellaneous symbols V V 6 5

AR-ANNO-TEXT Miscellaneous text and callouts with associated leaders 0 V V V

Columns

AR-COLS-ENCL Column enclosures/fire protection 0 0.50 4 7

Doors

AR-DOOR-FULL Full height (to ceiling) door: swing and leaf 0 0.25 3 2

AR-DOOR-IDEN Door number and symbol, hardware group, etc. 0 0.25 3 2

AR-DOOR-PRHT Partial height door: swing and leaf 0 0.35 6 5

AR-DOOR-SYMB Miscellaneous door symbols (e.g., overhead, bifold, pocket, etc) 0 0.25 1 3

Floor Information

AR-FLOR-CASE Casework (manufactured cabinets) 0 0.25 3 2

AR-FLOR-EVTR Elevator cars and equipment 0 0.35 2 4

AR-FLOR-FIXT Plumbing fixtures 0 0.25 201 29

AR-FLOR-HRAL Stair and balcony handrails, guard rails 0 0.25 1 3

AR-FLOR-IDEN Room name, space identification text 0 0.35 3 2

AR-FLOR-LEVL Level changes, shafts, ramps, pits, breaks in construction, and depressions 0 0.35 6 5

AR-FLOR-NUMB Room/space identification number and symbol 0 0.35 3 2

AR-FLOR-OTLN Floor outline/perimeter/building footprint 0 0.50 4 7

AR-FLOR-OTLN-RPRM Room perimeter shape (interior walls) 0 0.35 2 4

AR-FLOR-OVHD Overhead items (skylights, overhangs, etc.) 2 0.18 8 9




Model File Type: Floor Plan


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

AR-FLOR-PATT Paving, tile, carpet patterns 0 0.18 8 9

AR-FLOR-RAIS Access (raised) flooring 0 0.25 3 2

AR-FLOR-SIGN Signage 0 0.25 1 3

AR-FLOR-SPCL Architectural specialties (e.g., toilet room accessories, display cases) 0 0.25 3 2

AR-FLOR-STRS Stair risers/treads, escalators, ladders 0 0.25 1 3

AR-FLOR-TPTN Toilet partitions 0 0.25 1 3

AR-FLOR-WDWK Architectural woodwork (field built cabinets and counters) 0 0.25 3 2

Windows

AR-GLAZ-FULL Full height glazed walls and partitions (see AR-WALL-CWMG for curtain walls) 0 0.25 1 3

AR-GLAZ-IDEN Window number and symbol 0 0.35 3 2

AR-GLAZ-PRHT Windows and partial height glazed partitions 0 0.25 1 3

AR-GLAZ-SILL Window sills 0 0.18 5 1

Walls

AR-WALL-CAVI Cavity wall lines 0 0.18 8 9

AR-WALL-CNTR Wall centerlines 7 0.18 5 1

AR-WALL-CWMG Curtain wall mullions and glass 0 0.25 1 3

AR-WALL-FIRE Fire wall designators (patterning) 0 0.35 2 4

AR-WALL-FULL-EXTR Exterior full height walls 0 0.35 2 4

AR-WALL-FULL-INTR Interior full height walls 0 0.25 3 2

AR-WALL-HEAD Door and window headers 0 0.25 1 3

AR-WALL-IDEN Wall identification/type text or tags 0 0.35 3 2

AR-WALL-JAMB Door and window jambs 0 0.25 1 3

AR-WALL-MOVE Moveable walls/partitions 0 0.18 5 1

AR-WALL-OPEN-LVRS Louvers 0 0.25 1 3

AR-WALL-PATT Wall insulation, hatching, and fill INBATT 0.18 8 9

AR-WALL-PRHT Partial height walls (do not appear on Reflected Ceiling Plan) 0 0.25 1 3

AR-WALL-SPCL Wall-hung/attached specialties (e.g., fixtures, grab bars (incl. handicap), telephone booths) 0 0.25 1 3




Model File Type: Reflected Ceiling Plan


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information











Ceiling Information

AR-CLNG-ACCS Access panels 0 0.35 6 5

AR-CLNG-CTLJ Ceiling control joints 0 0.35 2 4

AR-CLNG-GRID Ceiling grid 0 0.25 1 3

AR-CLNG-LITE Specialty ceiling lights not shown on the Electrical Lighting Plan 0 0.50 4 7

AR-CLNG-OPNG Openings, ceiling/roof penetrations (see also AR-FLOR-OVHD in Floor Plan model file 0 0.18 8 9

AR-CLNG-PATT Ceiling patterns 0 0.18 8 9

AR-CLNG-SFFT Soffits 0 0.25 2 4

AR-CLNG-SUSP Suspended elements, ceiling mounted specialties (e.g., clocks, fans, etc. 0 0.18 5 1

AR-CLNG-TEES Main tees 0 0.18 5 1



TABLE 46 Discipline: Architectural

Model File Type: Roof Plan


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information











Roof Information

AR-ROOF-CRTS Crickets flow arrows flow info 0 0.25 1 3

AR-ROOF-EXPJ Expansion joints 0 0.18 5 1

AR-ROOF-GUTR Roof internal gutters 0 0.18 8 9

AR-ROOF-HRAL Stair handrails, nosings, guard rails 0 0.18 5 1

AR-ROOF-LEVL Level changes 0 0.18 5 1

AR-ROOF-OTLN Roof perimeter/edge, roof geometry 0 0.35 6 5

AR-ROOF-PATT Roof surface patterns, hatching 0 0.18 8 9

AR-ROOF-RFDR Roof drains 0 0.25 1 3

AR-ROOF-SPCL Roof specialties, accessories, access hatches, dormers 0 0.25 3 2

AR-ROOF-STRS Stair risers/treads, ladders 0 0.18 5 1

AR-ROOF-WALK Roof walkways 0 0.25 3 2

AR-ROOF-WALL Parapet walls and wall caps 0 0.35 2 4




Model File Type: Equipment Plan


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information











Equipment

AR-EQPM-ACCS Equipment access 0 0.35 6 5

AR-EQPM-FIXD Fixed equipment 0 0.50 4 7

AR-EQPM-IDEN Equipment identification numbers 0 0.35 6 5

AR-EQPM-MOVE Moveable equipment 0 0.35 6 5

AR-EQPM-OVHD Overhead, ceiling mounted, or suspended equipment 0 0.35 6 5




Model File Type: Area Calculations/Occupancy Plan


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information











Area Information

AR-AREA-IDEN Room numbers, tenant identifications, area calculations 0 0.35 2 4

AR-AREA-LINE Architectural area calculation boundary lines 0 0.50 4 7

AR-AREA-OCCP Occupant or employee names 0 0.35 2 4

AR-AREA-PATT Area cross hatching 0 0.18 8 9






Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information











Elevations

AR-ELEV-CASE Wall-mounted casework 0 0.25 3 2

AR-ELEV-FIXT Plumbing fixtures 0 0.35 2 4

AR-ELEV-FNSH Finishes, woodwork, trim 0 0.25 3 2

AR-ELEV-IDEN Component identification numbers 0 0.35 2 4

AR-ELEV-OTLN Building outlines 0 0.50 4 7

AR-ELEV-PATT Textures and hatch patterns 0 0.18 8 9

AR-ELEV-SIGN Signage 0 0.25 1 3






Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information











Sections

AR-SECT-IDEN Component identification numbers 0 0.35 2 4

AR-SECT-MBND Material beyond section cut 0 0.18 5 1

AR-SECT-MCUT Material cut by section V V V V

AR-SECT-PATT Textures and hatch patterns 0 0.18 8 9






Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information











Detail Information

AR-DETL-GRPH Graphics, gridlines, non-text items V V V V

AR-DETL-INPD Inch-pound specific dimensions and notes 0 V V V

AR-DETL-METR Metric specific dimensions and notes 0 V V V



4.12 Interiors

TABLE I-4-51 Discipline: Interiors



Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information

IN-ANNO-DIMS Witness extension lines, dimensions arrowheads and text 0 V V V

IN-ANNO-KEYN Keynote with associated leaderlines and arrowheads 0 V V V

IN-ANNO-NPLT Construction lines, reference targets, area calculations V 0 5 1

IN-ANNO-PATT Miscellaneous patterning 0 0 8 9

IN-ANNO-NOTE General note and general remarks 0 2 2 4

IN-ANNO-SYMB Reference bubbles, matchlines, breaklines V 2 6 5

IN-ANNO-TEXT Detail title text, leaderlines, arrowheads, notes 0 V V V

IN-STAT-DEMO Demolition 2 2 6 5

IN-STAT-EXST Existing to remain 0 1 3 2

IN-STAT-MOVE Items to be moved 5 2 6 5

IN-STAT-NICN Not in contract 3 0 8 9

IN-STAT-PHS# Phase numbers (# = 1-9) 0 2 2 4

IN-STAT-RELO Relocated items 2 0 5 1

IN-STAT-TEMP Temporary work 4 3 4 7

IN-DEMO-HAZW Hazardous waste 0 2 6 5




Model File Type: Furniture Plan


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information

IN-ANNO-DIMS Witness/extension lines, dimension terminators, dimension text 0 V V V

IN-ANNO-KEYN Reference keynotes with associated leaders 0 V V V

IN-ANNO-NOTE General notes and general remarks 0 0.35 2 4

IN-ANNO-NPLT Non-plotting graphic information 0 0.18 5 1

IN-ANNO-PATT Patterning, poche, shading, and hatching V 0.18 8 9

IN-ANNO-RDME Read-me information 0 0.18 5 1

IN-ANNO-REFR Reference files (AutoCAD users only) NA NA NA NA

IN-ANNO-SYMB Miscellaneous symbols V V 6 5

IN-ANNO-TEXT Miscellaneous text and callouts with associated leaders 0 V V V

Equipment

IN-EQPM-ACCS Equipment access 2 0.18 8 9

IN-EQPM-CHLD Child development (play toys, teaching rugs, play forms) 0 0.35 2 4

IN-EQPM-COPY Copiers, fax machines, office equipment 0 0.35 2 4

IN-EQPM-FIXD Fixed equipment 0 0.18 5 1

IN-EQPM-IDEN Equipment identification numbers 0 0.25 1 3

IN-EQPM-MEDI Medical (exam beds, dental chairs, etc.) 0 0.35 2 4

IN-EQPM-MOVE Moveable equipment 2 0.18 5 1

IN-EQPM-OVHD Overhead, ceiling mounted, and suspended equipment 0 0.25 3 2

IN-EQPM-STOR Storage equipment 0 0.35 2 4

Furnishings

IN-FURN-ACCS Accessories (vestibule matts, partitions, draperies, clocks, trash cans, lecturns, lamps, etc. 0 0.25 1 3

IN-FURN-ADPC Automated Data Processing Components 0 0.35 2 4

-FURN-ARTW Artwork 0 0.35 2 4

IN-FURN-FLOR Flooring (carpet, rugs, etc.) 0 0.35 2 4

IN-FURN-FREE Free-standing furnishings (desks, beds, tables, dressers, credenzas, casegoods) 0 0.35 6 5

IN-FURN-GRID Planning grid/modular outline 0 0.50 4 7

IN-FURN-IDEN Furniture code identification 0 0.25 3 2

IN-FURN-PLNT Plants 0 0.25 3 2




Model File Type: Furniture Plan


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

IN-FURN-SEAT Seating (chairs, sofas, etc.) 0 0.35 2 4

IN-FURN-STOR File cabinets, high density storage, shelving, storage cabinets 0 0.35 2 4




Model File Type: System Furniture Workstation Plan


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information










System Furniture

IN-SYST-FURN Furniture 0 0.35 2 4

IN-SYST-IDEN Code identification components 0 0.25 1 3

IN-SYST-IDPL Code identification panels 0 0.25 1 3

IN-SYST-LITE Lighting components 0 0.50 4 7

IN-SYST-PATT Patterns 0 0.18 8 9

IN-SYST-PNLS Panels 0 0.35 2 4

IN-SYST-POWR Power, communication components 0 0.50 4 7

IN-SYST-STOR Storage components 0 0.35 2 4

IN-SYST-WALL System furniture partition walls 0 0.35 2 4

IN-SYST-WKSF Work surface components 0 0.35 2 4




Model File Type: Signage Placement Plan


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information










Signage

IN-FLOR-SIGN Signage 0 0.35 6 5




Model File Type: Floor Patterns


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information










Carpet/Carpet Tile

IN-CRPT-ROLL-ACNT Carpet (roll goods) - accent color 0 V 1 3

IN-CRPT-ROLL-FILD Carpet (roll goods) - field color 0 V 60 100

IN-CRPT-TILE-ACN1 Carpet tile - accent color 0 V 208 69

IN-CRPT-TILE-ACN2 Carpet tile - accent color 0 V 236 139

IN-CRPT-TILE-FILD Carpet tile - field color 0 V 204 37

Flooring Items and Materials

IN-FLRG-MATS Entrance mat components and frames 0 V 4 7

IN-FLRG-STON Stone flooring 0 V 153 104

IN-FLRG-TRAN All floor thresholds and transition moldings 0 V 5 1

IN-FLRG-WOOD Wood parquet tile or planks 0 V 22 22

Monolithic (Poured of Broadcast) Flooring

IN-MONO-SRFL-ACNT Seamless resinous flooring - accent color 0 V 203 45

IN-MONO-SRFL-FILD Seamless resinous flooring - field color 0 V 9 14

IN-MONO-TERR-ACN1 Terrazzo - accent color 0 V 144 199

IN-MONO-TERR-ACN2 Terrazzo - accent color 0 V 67 156

IN-MONO-TERR-FILD Terrazzo - field color 0 V 239 163

Resilient Flooring

IN-SHTP-ACNT Sheet product (vinyl/rubber/linoleum) - accent color 0 V 190 245

IN-SHTP-FILD Sheet product (vinyl/rubber/linoleum) - field color 0 V 241 179




Model File Type: Floor Patterns


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

Tile

IN-TILE-CERM-ACNT Ceramic mosaic tile - accent color 0 V 153 104

IN-TILE-CERM-FILD Ceramic mosaic tile - field color 0 V 124 39

IN-TILE-LINO-ACNT Linoleum tile - accent color 0 V 236 139

IN-TILE-LINO-FILD Linoleum tile - field color 0 V 60 100

IN-TILE-PORC-ACN1 Porcelain tile - accent color 0 V 78 244

IN-TILE-PORC-ACN2 Porcelain tile - accent color 0 V 9 14

IN-TILE-PORC-FILD Porcelain tile - field color 0 V 128 71

IN-TILE-QUAR-ACNT Quarry tile - accent color 0 V 2 4

IN-TILE-QUAR-FILD Quarry tile - field color 0 V 30 86

IN-TILE-RUBB-ACNT Rubber tile - accent color 0 V 209 93

IN-TILE-RUBB-FILD Rubber tile - field color 0 V 20 6

IN-TILE-TERR-ACN1 Terrazzo tile - accent color 0 V 144 199



IN-TILE-TERR-FILD Terrazzo tile - field color 0 V 239 163

IN-TILE-VNYL-ACN1 Vinyl or Vinyl composition tile - accent color 0 V 203 45

IN-TILE-VNYL-ACN2 Vinyl or Vinyl composition tile - accent color 0 V 115 48

IN-TILE-VNYL-FILD Vinyl or Vinyl composition tile - field color 0 V 89 90






Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information










Elevations

IN-ELEV-CASE Wall mounted casework 0 0.35 2 4

IN-ELEV-FIXT Plumbing fixtures 0 0.25 3 2

IN-ELEV-FNSH Finishes, woodwork and trim 0 0.35 2 4

IN-ELEV-IDEN Component identification numbers 0 0.25 1 3

IN-ELEV-PATT Textures and hatch patterns 0 0.18 5 1

IN-ELEV-SIGN Signage 0 0.25 1 3






Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information










Detail Information

IN-DETL-GRPH Graphics, gridlines, non-text items V V V V

IN-DETL-INPD Inch-pound specific dimensions and notes 0 V V V

IN-DETL-METR Metric specific dimensions and notes 0 V V V



4.13 Fire Protection

TABLE I-4-58 Discipline: Fire Protection



Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information

FP-ANNO-DIMS Witness/extension lines, dimensions, arrowheads and text 0 0 7 0

FP-ANNO-KEYN Keynotes with associated leader lines and arrowheads 0 0 7 0

FP-ANNO-NPLT Construction lines, reference targets, area calculators 0 1 5 1

FP-ANNO-PATT Miscellaneous patterning 0 0 8 9

FP-ANNO-NOTE General notes and general remarks 0 2 2 4

FP-ANNO-SYMB Reference bubbles V 2 6 5

FP-ANNO-TEXT Detail title text, text, leader lines, arrowheads, notes 0 1 7 0

FP-ANNO-MATCH Match lines 0 5 1 3

FP-ANNO-BRK Break lines 0 0 2 4

FP-STAT-DEMO Demolition 2 2 6 5

FP-STAT-EXST Existing to remain 0 1 3 2

FP-STAT-MOVE Items to be removed 5 2 6 5

FP-STAT-NICN Not in contract 3 0 8 9

FP-STAT-PHS# Phase numbers (# =1-9) 0 2 2 4

FP-STAT-RELO Relocated items 2 0 5 1

FP-STAT-TEMP Temporary work 4 3 4 7

FP-DEMO-HAZW Hazardous waste 0 2 6 5




Model File Type: Life Safety Plan


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information

FP-ANNO-DIMS Witness/extension lines, dimension terminators, dimension text 0 V V V

FP-ANNO-KEYN Reference keynotes with associated leaders 0 V V V

FP-ANNO-NOTE General notes and general remarks 0 0.35 2 4

FP-ANNO-NPLT Non-plotting graphic information 0 0.18 5 1

FP-ANNO-PATT Patterning, poche, shading, and hatching 0 0.18 8 9

FP-ANNO-RDME Read-me information 0 0.18 5 1

FP-ANNO-REFR Reference files (AutoCAD users only) NA NA NA NA

FP-ANNO-SYMB Miscellaneous symbols V V 6 5

FP-ANNO-TEXT Miscellaneous text and callouts with associated leaders 0 V V V

Control Panels

FP-CTRL-PANL Control panels 0 0.50 23 46

Floor Information

FP-FLOR-IDEN Room name, space identification text (copied from Architectural - Floor Plan model 0 0.25 3 2

FP-FLOR-NUMB Room/space identification number and symbol (copied from Architectural – Floor Plan model file) 0 0.25 3 2

Means of Egress Lighting

FP-LITE-EMER Emergency fixtures 0 0.50 23 46

FP-LITE-EXIT Exit fixtures 0 0.50 203 45

Egress Requirements

FP-LSFT-EGRE Egress requirements designator 0 0.35 6 5

FP-LSFT-OCCP Occupant load for egress capacity 0 0.35 6 5

FP-LSFT-TRVL Maximum travel distances 0 0.35 6 5

Fire Protection/Suppression/Alarm/Detection Equipment

FP-PROT-ALRM-MANL Manual fire alarm pull stations 0 0.50 23 46

FP-PROT-EXTN Fire extinguishers 0 0.35 2 4

FP-PROT-EXTN-CABN Fire extinguisher cabinets 0 0.35 2 4

FP-PROT-HOSE Fire hoses 0 0.35 2 4

FP-PROT-HOSE-CABN Fire hose cabinets 0 0.35 2 4




Model File Type: Life Safety Plan


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

Fire Ratings

FP-RATE-DOOR Door fire ratings 0 0.50 4 7

FP-RATE-WALL Wall fire ratings 0 0.50 4 7

Smoke/Pressurization Control

FP-SMOK-DMPR Dampers 0 0.35 22 22




Model File Type: Fire Suppression Plan


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information










Aqueous Film Forming Foam System

FP-AFFFP-EQPM Equipment 0 0.35 82 18

FP-AFFFP-PIPE Piping 0 0.35 82 18

CO2 Sprinkler System

FP-CO2S-EQPM Equipment 0 0.35 6 5

FP-CO2S-PIPE CO2 piping or CO2 discharge nozzle piping 0 0.35 6 5

Floor Information

FP-FLOR-IDEN Room name, space identification text (copied from Architectural - Floor Plan model 0 0.25 3 2

FP-FLOR-NUMB Room/space identification number and symbol (copied from Architectural – Floor Plan model file) 0 0.25 3 2

Halon System

FP-HALN-EQPM Equipment 0 0.35 22 22

FP-HALN-PIPE Piping 0 0.35 22 22

Inert Gas

FP-IGAS-EQPM Equipment 0 0.35 162 33

FP-IGAS-PIPE Piping 0 0.35 162 33

Sprinkler System FP-SPRN-CLHD Sprinkler - ceiling heads 0 0.35 122 23

FP-SPRN-OTHD Sprinkler - other heads 0 0.35 122 23




Model File Type: Fire Suppression Plan


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

FP-SPRN-PIPE Sprinkler piping SPRINK 0.50 4 7

FP-SPRN-STAN Standpipe system 0 0.35 122 23

Water Supply and Distribution

FP-WATR-CONN Fire department connections 0 0.35 122 23

FP-WATR-HYDR Hydrants 0 0.35 122 23

FP-WATR-PIPE Piping FIRE 0.50 4 7

FP-WATR-PUMP Fire pumps 0 0.35 122 23






Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information










Detail Information

FP-DETL-GRPH Graphics, gridlines, non-text items V V V V

FP-DETL-INPD Inch-pound specific dimensions and notes 0 V V V

FP-DETL-METR Metric specific dimensions and notes 0 V V V




Model File Type: Riser Diagrams


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information

FP-ANNO-DIMS Witness/extension lines, dimensions, arrowheads and text 0 0 7 0

FP-ANNO-KEYN Keynotes with associated leader lines and arrowheads 0 0 7 0

FP-ANNO-NPLT Construction lines, reference targets, area calculators 0 1 5 1

FP-ANNO-PATT Miscellaneous patterning 0 0 8 9

FP-ANNO-NOTE General notes and general remarks 0 2 2 4

FP-ANNO-SYMB Reference bubbles V 2 6 5

FP-ANNO-TEXT Detail title text, text, leader lines, arrowheads, notes 0 1 7 0

FP-ANNO-MATCH Match lines 0 5 1 3

FP-ANNO-BRK Break lines 0 0 2 4

FP-ALRM-DUCT Smoke detectors, heat sensors 0 1 3 2

FP-LINFA-LW18 Extra fine line work V 0 5 1

FP-LINFA-LW25 Fine line work V 1 1 3

FP-LINFA-LW35 Medium line work V 2 2 4

FP-LINFA-LW50 Wide line work V 3 4 7

FP-LINFA-LW70 Extra wide line work V 4 7 0

FP-STAT-DEMO Demolition 2 2 6 5

FP-STAT-EXST Existing to remain 0 1 3 2

FP-STAT-FUTR Future work 7 2 2 4

FP-STAT-MOVE Items to be removed 5 2 6 5

FP-STAT-NICN Not in contract 3 0 8 9

FP-STAT-PHS# Phase numbers (# =1-9) 0 2 2 4

FP-STAT-RELO Relocated items 2 0 5 1

FP-STAT-TEMP Temporary work 4 3 4 7

FP-DEMO-HAZW Hazardous waste 0 2 6 5



4.14 Fire Alarm System

TABLE I-4-63 Discipline: Fire Alarm System

Model File Type: Demolition


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information

FA-ANNO-DIMS Witness/extension lines, dimensions, arrowheads and text 0 0 7 0

FA-ANNO-KEYN Keynotes with associated leader lines and arrowheads 0 0 7 0

FA-ANNO-NPLT Construction lines, reference targets, area calculators 0 1 5 1

FA-ANNO-PATT Miscellaneous patterning 0 0 8 9

FA-ANNO-NOTE General notes and general remarks 0 2 2 4

FA-ANNO-SYMB Reference bubbles V 2 6 5

FA-ANNO-TEXT Detail title text, text, leader lines, arrowheads, notes 0 1 7 0

FA-ANNO-MATCH Match lines 0 5 1 3

FA-ANNO-BRK Break lines 0 0 2 4

FA-STAT-DEMO Demolition 2 2 6 5

FA-STAT-EXST Existing to remain 0 1 3 2

FA-STAT-MOVE Items to be removed 5 2 6 5

FA-STAT-NICN Not in contract 3 0 8 9

FA-STAT-PHS# Phase numbers (# =1-9) 0 2 2 4

FA-STAT-RELO Relocated items 2 0 5 1

FA-STAT-TEMP Temporary work 4 3 4 7

FA-DEMO-HAZW Hazardous waste 0 2 6 5



TABLE I-4-64 Discipline: Fire Alarm

Model File Type: Fire Alarm/Detection Plan


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information

FA-ANNO-DIMS Witness/extension lines, dimension terminators, dimension text 0 V V V

FA-ANNO-KEYN Reference keynotes with associated leaders 0 V V V

FA-ANNO-NOTE General notes and general remarks 0 0.35 2 4

FA-ANNO-NPLT Non-plotting graphic information 0 0.18 5 1

FA-ANNO-PATT Patterning, poche, shading, and hatching V 0.18 8 9

FA-ANNO-RDME Read-me information 0 0.18 5 1

FA-ANNO-REFR Reference files (AutoCAD users only) NA NA NA NA

FA-ANNO-SYMB Miscellaneous symbols V V 6 5

FA-ANNO-TEXT Miscellaneous text and callouts with associated leaders 0 V V V

Control Panels

FA-CTRL-PANL Control panels 0 0.50 23 46

Floor Information

FA-FLOR-IDEN Room name, space identification text (copied from Architectural - Floor Plan model 0 0.25 3 2

FA-FLOR-NUMB Room/space identification number and symbol (copied from Architectural - Floor

Plan model file) 0 0.25 3 2

Fire Protection/Suppression/Alarm/Detection Equipment

FA-PROT-ALRM-INDC Indicating appliances 0 0.50 83 42

FA-PROT-ALRM-MANL Manual fire alarm pull stations 0 0.50 23 46

F-PROT-SMOK Smoke detectors and heat sensors 0 0.50 23 46






Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information


FA-ANNO-NPLT Construction lines, reference targets, area calculators V 0 5 1






FA-DETL-GENF General features (miscellaneous items) 0 V V V

FA-DETL-ARCH Architectural features 0 2 2 4

FA-DETL-BUSS Bus bars and rods 0 1 3 2

FA-DETL-CABS Cabinets and enclosures 0 2 6 5

FA-DETL-INSL Insulation and coverings 0 1 3 2

FA-DETL-LTFX Light fixtures 0 2 2 4

FA-DETL-MOTR Motors 0 1 1 3

FA-DETL-PIPE Piping and conduit 0 2 2 4

FA-DETL-STRC Structural support features 0 1 1 3

FA-DETL-TRAY Cable trays 0 2 6 5

FA-DETL-WIRE Wire and cables 0 2 2 4

FA-DETL-XFRM Transformer 0 2 2 4






Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information


FA-ANNO-KEYN Keynotes with associated leader lines and arrowheads 0 0 7 0

FA-ANNO-NPLT Construction lines, reference targets, area calculators 0 1 5 1


FA-ANNO-NOTE General notes and general remarks 0 2 2 4





FA-ALRM-DUCT Smoke detectors, heat sensors 0 1 3 2

FA-LINFA-LW18 Extra fine line work V 0 5 1

FA-LINFA-LW25 Fine line work V 1 1 3

FA-LINFA-LW35 Medium line work V 2 2 4

FA-LINFA-LW50 Wide line work V 3 4 7

FA-LINFA-LW70 Extra wide line work V 4 7 0

FA-STAT-DEMO Demolition 2 2 6 5

FA-STAT-EXST Existing to remain 0 1 3 2

FA-STAT-FUTR Future work 7 2 2 4

FA-STAT-MOVE Items to be removed 5 2 6 5

FA-STAT-NICN Not in contract 3 0 8 9

FA-STAT-PHS# Phase numbers (# =1-9) 0 2 2 4

FA-STAT-RELO Relocated items 2 0 5 1

FA-STAT-TEMP Temporary work 4 3 4 7

FA-DEMO-HAZW Hazardous waste 0 2 6 5



4.15 Plumbing

TABLE I-4-67 Discipline: Plumbing



Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information

PL-ANNO-DIMS Witness extension lines, dimensions arrowheads and text 0 V V V

PL-ANNO-KEYN Keynote with associated leaderlines and arrowheads 0 V V V

PL-ANNO-NPLT Construction lines, reference targets, area calculations V 0 5 1

PL-ANNO-PATT Miscellaneous patterning 0 0 8 9

PL-ANNO-NOTE General note and general remarks 0 2 2 4

PL-ANNO-SYMB Reference bubbles, matchlines, breaklines V 2 6 5

PL-ANNO-TEXT Detail title text, leaderlines, arrowheads, notes 0 V V V

PL-STAT-DEMO Demolition 2 2 6 5

PL-STAT-EXST Existing to remain 0 1 3 2

PL-STAT-MOVE Items to be moved 5 2 6 5

PL-STAT-NICN Not in contract 3 0 8 9

PL-STAT-PHS# Phase numbers (# = 1-9) 0 2 2 4

PL-STAT-RELO Relocated items 2 0 5 1

PL-STAT-TEMP Temporary work 4 3 4 7

PL-DEMO-HAZW Hazardous waste 0 2 6 5




Model File Type: Piping Plan


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information

PL-ANNO-DIMS Witness/extension lines, dimension terminators, dimension text 0 V V V

PL-ANNO-KEYN Reference keynotes with associated leaders 0 V V V

PL-ANNO-NOTE General notes and general remarks 0 0.35 4 4

PL-ANNO-NPLT Non-plotting graphic information 0 0.18 5 1

PL-ANNO-PATT Patterning, poche, shading, and hatching V 0.18 8 9

PL-ANNO-RDME Read-me information 0 0.18 5 1

PL-ANNO-REFR Reference files (AutoCAD users only) NA NA NA NA

PL-ANNO-SYMB Miscellaneous symbols V V 6 5

PL-ANNO-TEXT Miscellaneous text and callouts with associated leaders 0 V V V

Domestic Water System

PL-DOMW-CPIP Cold water piping CLDWTR 0.50 123 31

PL-DOMW-EQPM Hot and cold water equipment 0 0.70 7 0

PL-DOMW-EQPM-ACCS Equipment access doors 0 0.35 82 18

PL-DOMW-FPIP Domestic filtered water piping 0 0.50 83 42

PL-DOMW-HPIP Hot water piping HWTR,

HWTRR 0.50 113 16

PL-DOMW-RISR Hot and cold water risers 2 0.25 3 2

Floor Information

PL-FLOR-IDEN Room name, space identification text (copied from Architectural - Floor Plan model) 0 0.25 3 2

PL-FLOR-NUMB Room/

space identification number and symbol (copied from Architectural – Floor Plan model file)

0 0.25 3 2

Laboratory Gas Piping

PL-LGAS-EQPM Equipment 0 0.70 24 38

PL-LGAS-PIPE Piping

OXYGEN

NITROG

HELIUM

HYDRGN

ACIDWS

0.50 23 46




Model File Type: Piping Plan


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

Medical/Dental Gas Piping

PL-MDGS-EQPM Equipment 0 0.70 24 38

PL-MDGS-NITG Nitrogen piping NITROG 0.50 23 46

PL-MDGS-NOXG Nitrous oxide piping NITOXI 0.50 23 46

PL-MDGS-OXYG Pure O2 piping OXYGEN 0.50 23 46

PL-MDGS-SAIR Scavenge air 0 0.50 23 46

PL-MDGS-VACU Medical vacuum piping VACAIR 0.50 23 46

Penetrations

PL-PENE-FLOR Floor penetrations 2 0.25 3 2

PL-PENE-ROOF Roof penetrations 2 0.25 1 3

PL-PENE-WALL Wall penetrations 2 0.25 2 4

Sanitary Drainage System

PL-SANR-COND Condensate piping 0 0.50 83 42

PL-SANR-EQPM Equipment (e.g., sand/oil/water separators) 0 0.70 201 37

PL-SANR-FLDR Floor drains, sinks, and cleanouts 0 0.35 6 5

PL-SANR-PIPE Piping SSWAF 0.50 203 45

PL-SANR-RISR Sanitary risers 2 0.50 203 45

PL-SANR-VENT Vent piping VENT 0.50 203 45

Storm Drainage System

PL-STRM-PIPE Storm drain piping STRAF 0.50 163 41

PL-STRM-RFDR Roof drains 0,

ROOFDN0.50 163 41

PL-STRM-RISR Storm drain risers 2 0.50 163 41






Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information










Detail Information

PL-DETL-GRPH Graphics, gridlines, non-text items V V V V

PL-DETL-INPD Inch-pound specific dimensions and notes 0 V V V

PL-DETL-METR Metric specific dimensions and notes 0 V V V






Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information










Diagram Information

PL-DIAG-GRPH Graphics, gridlines, non-text items V V V V

PL-DIAG-INPD Inch-pound specific dimensions and notes 0 V V V

PL-DIAG-METR Metric specific dimensions and notes 0 V V V



4.16 Mechanical

TABLE I-4-71 Discipline: Mechanical



Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information

ME-ANNO-DIMS Witness extension lines, dimensions arrowheads and text 0 V V V

ME-ANNO-KEYN Keynote with associated leaderlines and arrowheads 0 V V V

ME-ANNO-NPLT Construction lines, reference targets, area calculations V 0 5 1

ME-ANNO-PATT Miscellaneous patterning 0 0 8 9

ME-ANNO-NOTE General note and general remarks 0 2 2 4

ME-ANNO-SYMB Reference bubbles, matchlines, breaklines V 2 6 5

ME-ANNO-TEXT Detail title text, leaderlines, arrowheads, notes 0 V V V

ME-STAT-DEMO Demolition 2 2 6 5

ME-STAT-EXST Existing to remain 0 1 3 2

ME-STAT-MOVE Items to be moved 5 2 6 5

ME-STAT-NICN Not in contract 3 0 8 9

ME-STAT-PHS# Phase numbers (# = 1-9) 0 2 2 4

ME-STAT-RELO Relocated items 2 0 5 1

ME-STAT-TEMP Temporary work 4 3 4 7

ME-DEMO-HAZW Hazardous waste 0 2 6 5




Model File Type: HVAC Plan


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information

ME-ANNO-DIMS Witness/extension lines, dimension terminators, dimension text, weld symbols 0 V V V

ME-ANNO-KEYN Reference keynotes with associated leaders 0 V V V

ME-ANNO-MASK Text/shape mask for use with photo backgrounds 0 0.18 113 16

ME-ANNO-NOTE General notes and general remarks 0 0.35 2 4

ME-ANNO-NPLT Non-plotting graphic information (e.g., clearances and working space information) 0 0.18 5 1

ME-ANNO-PATT Patterning, poche, shading, and hatching V 0.18 8 9

ME-ANNO-RDME Read-me information 0 0.18 5 1

ME-ANNO-REFR Reference files (AutoCAD users only) NA NA NA NA

ME-ANNO-SYMB Miscellaneous symbols V V 6 5

ME-ANNO-TEXT Miscellaneous text and callouts with associated leaders 0 V V V

Chemical Treatment System

ME-CHEM-EQPM Chemical treatment system equipment 0 0.35 123 31

ME-CHEM-RETN-PIPE Chemical treatment system return piping 0 0.50 123 31

ME-CHEM-SUPP-PIPE Chemical treatment system supply piping 0 0.50 123 31

Condenser Water System

ME-CNDW-EQPM Condenser water system equipment 0 0.35 83 42

ME-CNDW-RETN-PIPE Condenser water system return piping CONDWR 0.50 83 42

ME-CNDW-SUPP-PIPE Condenser water system supply piping CONDWS 0.50 83 42

Controls

ME-CONT-THER Thermostats 0 0.25 1 3

ME-CONT-WIRE Low voltage wiring 1,2 0.25 1 3

Chilled Water System

ME-CWTR-CNDS-PIPE Condensate piping CDRNAF 0.50 83 42

ME-CWTR-EQPM Chilled water equipment 0 0.35 163 41

ME-CWTR-RETN-PIPE Chilled water return piping CWR 0.50 163 41

ME-CWTR-SUPP-PIPE Chilled water supply piping CWS 0.50 163 41






Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

Dual Temperature System

ME-DUAL-EQPM Dual temperature system equipment 0 0.35 23 46

ME-DUAL-RETN-PIPE Dual temperature system return piping DTR 0.50 23 46

ME-DUAL-SUPP-PIPE Dual temperature system supply piping DTS 0.50 23 46

Dust and Fume Collection System

ME-DUST-DUCT Dust and fume ductwork 0 0.50 203 45

ME-DUST-DUCT-CNTR Dust and fume ductwork centerlines 7 0.18 5 1

ME-DUST-EQPM Dust and fume equipment 0 0.35 203 45

ME-DUST-GRIL Dust and fume grilles 0 0.35 203 45

Exhaust Air System

ME-EXHS-DUCT Exhaust ductwork V 0.50 83 42 X X V 0.50 83 42

ME-EXHS-DUCT-CNTR Exhaust ductwork centerlines 7 0.18 5 1 X X 7 0.18 5 1

ME-EXHS-EQPM Exhaust equipment 0 0.35 83 42 X X 0 0.35 83 42

ME-EXHS-GRIL Grilles 0 0.35 83 42 0 0.35 83 42

Floor Information

ME-FLOR-IDEN Room name, space identification text (copied from Architectural - Floor Plan model) 0 0.25 3 2

ME-FLOR-NUMB Room/space identification number and symbol (copied from Architectural - Floor Plan model file) 0 0.25 3 2

Glycol System

ME-GLYC-EQPM Glycol system equipment 0 0.35 82 18

ME-GLYC-RETN-PIPE Glycol system return piping GHR 0.50 82 18

ME-GLYC-SUPP-PIPE Glycol system supply piping GHS 0.50 82 18

Geothermal Heat Pump System

ME-GTHP-EQPM Geothermal heat pump system equipment 0 0.35 203 45

ME-GTHP-RETN-PIPE Geothermal heat pump system return piping 0 0.50 203 45

ME-GTHP-SUPP-PIPE Geothermal heat pump system supply piping 0 0.50 203 45

High Temperature/Chilled Water System

ME-HTCW-ABND-PIPE Abandoned piping 2 0.25 1 3






Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

ME-HTCW-CWTR-MAIN Main chilled water piping 0 0.35 163 41

ME-HTCW-CWTR-PLNT Chilled water plant 0 0.35 163 41

ME-HTCW-CWTR-SERV Chilled water service piping 0 0.25 163 41

ME-HTCW-DEVC Rigid anchors, anchor guides, rectifiers, reducers, markers, meters, pumps,regulators, tanks, and valves 0 0.35 6 5

ME-HTCW-FLOW Flow direction arrows 0 0.25 3 2

ME-HTCW-FTTG Caps and flanges 0 0.35 6 5

ME-HTCW-HWTR-MAIN Main high temperature piping 0 0.35 113 16

ME-HTCW-HWTR-PLNT High temperature water plant 0 0.35 113 16

ME-HTCW-HWTR-SERV High temperature service piping 0 0.25 113 16

ME-HTCW-IDEN Identifier tags, symbol modifiers, and text 0 0.35 2 4

ME-HTCW-JBOX Junction boxes, manholes, handholes, test boxes 0 0.25 1 3

ME-HTCW-LWTR-MAIN Main low temperature piping 0 0.35 1 3

ME-HTCW-LWTR-SERV Low temperature service piping 0 0.25 1 3

ME-HTCW-PITS Valve pits/vaults, steam pits 0 0.25 3 2

ME-HTCW-PLNT-IDEN Water plant identifier tags, symbol modifiers, and text 0 0.35 2 4

ME-HTCW-RETN-PIPE Return for all HTCW lines 0 0.18 5 1

ME-HTCW-STEM-MAIN Main steam piping 0 0.35 113 16

ME-HTCW-STEM-SERV Steam service piping 0 0.25 113 16

ME-HTCW-STNS-IDEN Pump station identifier tags, symbol modifiers, and text 0 0.35 6 5

ME-HTCW-STNS-PUMP Pump stations 0 0.35 6 5

HVAC System

ME-HVAC-ACCS Equipment access doors 0,1,2 0.25 3 2

ME-HVAC-CDFF Ceiling diffusers, registers, and grilles 0 0.35 20 6

ME-HVAC-DMPR Fire, smoke, volume dampers 0 0.25 1 3






Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

ME-HVAC-EQPM Equipment (non-powered) 0 0.35 2 4

ME-HVAC-EQPM-EFAN Equipment with electric fans or motors 0 0.35 2 4

ME-HVAC-EQPM-EPIP Equipment with piping and electricity 0 0.35 2 4

ME-HVAC-EQPM-FLOR Equipment - floor mounted 0 0.35 2 4

ME-HVAC-EQPM-SUSP Equipment - suspended 0 0.35 2 4

ME-HVAC-FDFF Floor diffusers, registers, and grilles 0 0.35 162 33

ME-HVAC-IDEN Duct sizes and pressure classes 0 0.35 6 5

ME-HVAC-RDFF Return air diffusers 0 0.35 23 46

ME-HVAC-RETN Return ductwork V 0.50 23 46

ME-HVAC-RETN-CNTR Return ductwork centerlines 7 0.18 5 1

ME-HVAC-ROOF Roof mounted HVAC equipment 0 0.35 2 4

ME-HVAC-SUPP Supply ductwork V 0.50 4 7

ME-HVAC-SUPP-CNTR Supply ductwork centerlines 7 0.18 5 1

ME-HVAC-SUPP-HDUC Supply ductwork - high pressure V 0.50 4 7

ME-HVAC-SUPP-LDUC Supply ductwork - low pressure V 0.50 4 7

ME-HVAC-TAGS Diffuser/register/grille tags and air flow arrows 0 0.35 6 5

ME-HVAC-WDFF Wall diffusers, registers, and grilles 0 0.35 2 4

Hot Water Heating System

ME-HWTR-EQPM Hot water heating system equipment 0 0.35 113 16

ME-HWTR-RETN-PIPE Hot water heating system return piping HWR 0.50 113 16

ME-HWTR-SUPP-PIPE Hot water heating system supply piping HWS 0.50 113 16

Mixed Air System

ME-MAIR-DUCT Mixed air ductwork 0 0.50 7 0

ME-MAIR-DUCT-CNTR Mixed air ductwork centerlines 7 0.18 5 1

ME-MAIR-EQPM Mixed air equipment 0 0.35 7 0

Makeup Air System






Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

ME-MKUP-DUCT Makeup air ductwork 0 0.50 2 4

ME-MKUP-DUCT-CNTR Makeup air ductwork centerlines 7 0.18 5 1

ME-MKUP-EQPM Makeup air equipment 0 0.35 2 4

ME-MKUP-GRIL Makeup air grilles 0 0.35 2 4

Penetrations

ME-PENE-FLOR Floor penetrations 2 0.25 3 2

ME-PENE-ROOF Roof penetrations 2 0.25 1 3

ME-PENE-WALL Wall penetrations 2 0.25 2 4

Relief Air System

ME-RAIR-DUCT Relief air ductwork 0 0.50 1 3

ME-RAIR-DUCT-CNTR Relief air ductwork centerlines 7 0.18 5 1

ME-RAIR-EQPM Relief air equipment 0 0.35 1 3

ME-RAIR-GRIL Relief air grilles 0 0.35 1 3

Energy Recovery System

ME-RCOV-EQPM Energy recovery system equipment 0 0.35 203 45

ME-RCOV-RETN-PIPE Energy recovery system return piping 0 0.50 203 45

ME-RCOV-SUPP-PIPE Energy recovery system supply piping 0 0.50 203 45

Refrigeration System

ME-REFG-DISC-PIPE Refrigeration system REFRD 0.50 163 41

ME-REFG-EQPM Refrigeration system equipment 0 0.35 163 41

ME-REFG-RETN-PIPE Refrigeration system return piping REFRS 0.50 163 41

ME-REFG-SUPP-PIPE Refrigeration system supply piping REFRL 0.50 163 41

Steam System

ME-STEME-BLBD-PIPE Boiler blow down piping BOILBD 0.50 113 16

ME-STEME-CNDS-PIPE Condensate piping CDRNAF 0.50 83 42

ME-STEME-EQPM Steam system equipment 0 0.35 113 16

ME-STEME-HPIP-PIPE High pressure steam piping STEAMH 0.50 113 16

ME-STEME-LPIP-PIPE Low pressure steam piping STEAML 0.50 1 3






Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

ME-STEME-MPIP-PIPE Medium pressure steam piping STEAMM 0.50 2 4

Transfer Air System

ME-TAIR-DUCT Transfer air ductwork 0 0.50 200 13

ME-TAIR-DUCT-CNTR Transfer air ductwork centerlines 7 0.18 5 1

ME-TAIR-EQPM Transfer air equipment 0 0.35 200 13




Model File Type: Specialty Piping and Equipment Plan


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information











Industrial Waste Piping

ME-ACID-EQPM Acid, alkaline, and oil waste equipment 0 0.35 80 11

ME-ACID-PIPE Acid, alkaline, and oil waste piping ACIDWS,

IWASTE0.50 80 11

ME-ACID-VENT Acid, alkaline, and oil waste vent piping 2 0.50 80 11

Anti-Freeze

ME-AFRZ-EQPM Anti-freeze equipment 0 0.35 82 18

ME-AFRZ-SUPP-PIPE Anti-freeze supply piping 0 0.50 82 18

ME-AFRZ-WAST-PIPE Anti-freeze waste piping 0 0.50 82 18

Brine System

ME-BRIN-EQPM Brine system equipment 0 0.35 123 31

ME-BRIN-RETN-PIPE Brine system return piping BRINER BRINER 0.50 123 31

ME-BRIN-SUPP-PIPE Brine system supply piping BRINES BRINES 0.50 123 31

Compressed Air

ME-CMPA-EQPM Equipment 0 0.70 84 34

ME-CMPA-PIPE Piping CMPAIR 0.50 83 42

Floor Information






Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

ME-FLOR-IDEN Room name, space identification text (copied from Architectural - Floor Plan model) 0 0.25 3 2

ME-FLOR-NUMB Room/space identification number and symbol (copied from Architectural - Floor Plan model file) 0 0.25 3 2

Fuel System

ME-FUEL-EQPM Equipment 0 0.70 24 38

ME-FUEL-GGEP-LQPG Liquid petroleum gas LIQPET 0.50 23 46

ME-FUEL-OGEP-RETN Return oil piping FUELOR 0.50 23 46

ME-FUEL-OGEP-SUPP Supply oil piping FUELOS 0.50 23 46

ME-FUEL-OGEP-VENT Oil piping vent FUELOV 0.50 23 46

Glycol System

ME-GLYC-EQPM Glycol system equipment 0 0.35 82 18

ME-GLYC-RETN-PIPE Glycol system return piping GHR 0.50 82 18

ME-GLYC-SUPP-PIPE Glycol system supply piping GHS 0.50 82 18

Hydraulic Control Systems (Hydraulic Fluid)

ME-HCSF-EQPM Hydraulic system equipment 0 0.35 200 13

ME-HCSF-RETN-PIPE Hydraulic system return piping 0 0.50 120 12 X 0 0.35 120 12

ME-HCSF-SUPP-PIPE Hydraulic system supply piping 0 0.50 200 13 X 0 0.50 200 13

Insulating (Transformer) Oil System

ME-INSL-EQPM Insulating oil equipment 0 0.35 200 13

ME-INSL-RETN-PIPE Insulating oil return piping 0 0.50 200 13

ME-INSL-SUPP-PIPE Insulating oil supply piping 0 0.50 200 13

Lubrication Oil

ME-LUBE-EQPM ME-LUBEEQME- Lubrication oil equipment 0 0.35 200 13 X X 0 0.35 200 13

ME-LUBE-RETN-PIPE ME-LUBERPME- Lubrication oil return piping 0 0.50 200 13 X X 0 0.50 200 13

ME-LUBE-SUPP-PIPE ME-LUBESPME- Lubrication oil supply piping 0 0.50 200 13 0 0.50 200 13

Natural Gas System

ME-NGAS-EQPM Natural gas equipment 0 0.35 6 5

ME-NGAS-PIPE Natural gas piping NTGASN 0.35 6 5

Penetrations






Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

ME-PENE-FLOR Floor penetrations 2 0.25 3 2

ME-PENE-ROOF Roof penetrations 2 0.25 1 3

ME-PENE-WALL Wall penetrations 2 0.25 2 4

Process Piping

ME-PROC-EQPM Process equipment 0 0.35 120 12

ME-PROC-RETN-PIPE Process return piping 0 0.50 120 12

ME-PROC-SUPP-PIPE Process supply piping 0 0.50 120 12

Raw Water Piping

ME-RWTR-EQPM Raw water equipment 0 0.35 123 31

ME-RWTR-RETN-PIPE Raw water return piping 0 0.50 123 31

ME-RWTR-SUPP-PIPE Raw water supply piping 0 0.50 123 31




Model File Type: HTCW Utilities Plan


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information











Geothermal Heat Pump System

ME-GTHP-EQPM Geothermal heat pump system equipment 0 0.35 203 45

ME-GTHP-RETN-PIPE Geothermal heat pump system return piping 0 0.50 203 45

ME-GTHP-SUPP-PIPE Geothermal heat pump system supply piping 0 0.50 203 45

High Temperature/Chilled Water System

ME-HTCW-ABND-PIPE Abandoned piping 2 0.25 1 3

ME-HTCW-CWTR-MAIN Main chilled water piping 0 0.35 163 41

ME-HTCW-CWTR-PLNT Chilled water plant 0 0.35 163 41

ME-HTCW-CWTR-SERV Chilled water service piping 0 0.25 163 41

ME-HTCW-DEVC Rigid anchors, anchor guides, rectifiers, reducers, markers, meters, pumps,regulators, tanks, and valves 0 0.35 6 5

ME-HTCW-FLOW Flow direction arrows 0 0.25 3 2

ME-HTCW-FTTG Caps and flanges 0 0.35 6 5

ME-HTCW-HWTR-MAIN Main high temperature piping 0 0.35 113 16

ME-HTCW-HWTR-PLNT High temperature water plant 0 0.35 113 16

ME-HTCW-HWTR-SERV High temperature service piping 0 0.25 113 16




Model File Type: HTCW Utilities Plan


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

ME-HTCW-IDEN Identifier tags, symbol modifiers, and text 0 0.35 2 4

ME-HTCW-JBOX Junction boxes, manholes, handholes, test boxes 0 0.25 1 3

ME-HTCW-LWTR-MAIN Main low temperature piping 0 0.35 1 3

ME-HTCW-LWTR-SERV Low temperature service piping 0 0.25 1 3

ME-HTCW-PITS Valve pits/vaults, steam pits 0 0.25 3 2

ME-HTCW-PLNT-IDEN Water plant identifier tags, symbol modifiers, and text 0 0.35 2 4

ME-HTCW-RETN-PIPE Return for all HTCW lines 0 0.18 5 1

ME-HTCW-STEM-MAIN Main steam piping 0 0.35 113 16

ME-HTCW-STEM-SERV Steam service piping 0 0.25 113 16

ME-HTCW-STNS-IDEN Pump station identifier tags, symbol modifiers, and text 0 0.35 6 5

ME-HTCW-STNS-PUMP Pump stations 0 0.35 6 5




Model File Type: Material Handling


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information











Material Handling Equipment

ME-MATL-CRAN Cranes 0 0.35 2 4

ME-MATL-CRAN-BOOM Crane, boom 0 0.35 2 4

ME-MATL-HOIS Hoists 0 0.35 2 4

ME-MATL-HOOK Hooks, eyes, and other end attachments 0 0.35 2 4

ME-MATL-LIFT Miscellaneous lifting equipment 0 0.35 6 5

ME-MATL-WIRE Wire rope, chains, and other hoisting medium 0 0.35 6 5




Model File Type: Machine Design


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information











Machine Design

ME-MACH-AXLE Shafts and axles 0 0.35 2 4

ME-MACH-BASE Machinery bases 0 0.35 2 4

ME-MACH-BEAR Bearings and couplings 0 0.35 2 4

ME-MACH-BELT Wire rope, chains, and belts 0 0.35 22 22

ME-MACH-BSHG Bushings, wear plates, shims, and spacers 0 0.35 2 4

ME-MACH-CLEV Clevises 0 0.35 22 22

ME-MACH-COMP Miscellaneous machinery parts and components 0 0.35 2 4

ME-MACH-COVR Machinery covers, cover plates, and guarding 0 0.35 4 7

ME-MACH-FSTN Fasteners, nuts, and bolts 0 0.35 2 4

ME-MACH-GEAR Gears 0 0.35 6 5

ME-MACH-KEYS Keys and keeper plates 0 0.35 22 22

ME-MACH-LROT Large rotating machinery (turbine and pump outlines) 0 0.35 6 5

ME-MACH-MOTR Machinery motors 0 0.35 6 5

ME-MACH-PINS Pins 0 0.35 22 22

ME-MACH-PULL Pulleys, drums, and sheaves 0 0.35 22 22

ME-MACH-RAIL Rails (e.g., crane rails, rail hoots, splice plates, etc.) 0 0.35 22 22

ME-MACH-ROLL Rollers and wheels 0 0.35 22 22




Model File Type: Machine Design


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

ME-MACH-ROLL-TRAK Roller tracks 0 0.35 22 22

ME-MACH-SEAL Seals 0 0.35 22 22

ME-MACH-SHOE Sliding shoes, skids, etc. 0 0.35 22 22

ME-MACH-SPPT Support brackets 0 0.35 2 4

ME-MACH-SPRG Springs 0 0.35 22 22






Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information











Elevations

ME-ELEV-FIXT Miscellaneous fixtures 0 0.35 6 5

ME-ELEV-IDEN Component identification numbers 0 0.35 2 4

ME-ELEV-OTLN Building outlines 0 0.35 6 5

ME-ELEV-PATT Textures and hatch patterns 0 0.18 8 9






Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information











Sections

ME-SECT-IDEN Component identification numbers 0 0.35 2 4

ME-SECT-MBND Material beyond section cut 0 0.18 5 1

ME-SECT-MCUT Material cut by section 0 0.50 4 7

ME-SECT-PATT Textures and hatch patterns 0 0.18 8 9






Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information











Detail information

ME-DETL-GRPH Graphics, gridlines, non-text items V V V V

ME-DETL-INPD Inch-pound specific dimensions and notes 0 V V V

ME-DETL-METR Metric specific dimensions and notes 0 V V V




Model File Type: Control Diagrams


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information











Diagram Information

ME-DIAG-GRPH Graphics, gridlines, non-text items V V V V

ME-DIAG-INPD Inch-pound specific dimensions and notes 0 0.25 1 3

ME-DIAG-METR Metric specific dimensions and notes 0 0.25 3 2



4.17 Electrical

TABLE I-4-81 Discipline: Electrical



Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information

EL-ANNO-DIMS Witness extension lines, dimensions arrowheads and text 0 V V V

EL-ANNO-KEYN Keynote with associated leaderlines and arrowheads 0 V V V

EL-ANNO-NPLT Construction lines, reference targets, area calculations V 0 5 1

EL-ANNO-PATT Miscellaneous patterning 0 0 8 9

EL-ANNO-NOTE General note and general remarks 0 2 2 4

EL-ANNO-SYMB Reference bubbles, matchlines, breaklines V 2 6 5

EL-ANNO-TEXT Detail title text, leaderlines, arrowheads, notes 0 V V V

EL-STAT-DEMO Demolition 2 2 6 5

EL-STAT-EXST Existing to remain 0 1 3 2

EL-STAT-MOVE Items to be moved 5 2 6 5

EL-STAT-NICN Not in contract 3 0 8 9

EL-STAT-PHS# Phase numbers (# = 1-9) 0 2 2 4

EL-STAT-RELO Relocated items 2 0 5 1

EL-STAT-TEMP Temporary work 4 3 4 7

EL-DEMO-HAZW Hazardous waste 0 2 6 5




Model File Type: Lighting Plan


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information

EL-ANNO-DIMS Witness/extension lines, dimension terminators, dimension text 0 V V V

EL-ANNO-KEYN Reference keynotes with associated leaders 0 V V V

EL-ANNO-MASK Text/shape mask for use with photo backgrounds 0 0.18 113 16

EL-ANNO-NOTE General notes and general remarks 0 0.35 2 4

EL-ANNO-NPLT Non-plotting graphic information 0 0.18 5 1

EL-ANNO-PATT Patterning, poche, shading, and hatching V 0.18 8 9

EL-ANNO-RDME Read-me information 0 0.18 5 1

EL-ANNO-REFR Reference files (AutoCAD users only) NA NA NA NA

EL-ANNO-SYMB Miscellaneous symbols V V 6 5

EL-ANNO-TEXT Miscellaneous text and callouts with associated leaders 0 V V V

Floor Information

EL-FLOR-IDEN Room name, space identification text (copied from Architectural - Floor Plan model 0 0.25 3 2

EL-FLOR-NUMB Room/space identification number and symbol (copied from Architectural – Floor Plan model file) 0 0.25 3 2

Lighting

EL-LITEL-CIRC Lighting circuits (including crosslines and homeruns) 0 0.50 83 42

EL-LITEL-CIRC-NUMB Lighting circuit numbers (e.g., panel/circuit number, wire/conduit size) 0 0.35 2 4

EL-LITEL-CLNG Ceiling mounted (surface/pendant) fixtures 0 0.50 203 45

EL-LITEL-EMER Emergency fixtures (outline of light (if ceiling mounted) should go on EL-LITEL-CLNG 0 0.50 23 46

EL-LITEL-EXIT Exit fixtures (outline of light (if ceiling mounted) should go on EL-LITEL-CLNG) 0 0.50 203 45

EL-LITEL-FLOR Floor mounted fixtures (e.g., stage) 0 0.50 203 45

EL-LITEL-IDEN Light fixture identifier tags 0 0.35 2 4

EL-LITEL-JBOX Junction boxes 0 0.50 83 42

EL-LITEL-PANL Main distribution panels, switchboards, lighting panels 0 0.50 4 7

EL-LITEL-ROOF Roof lighting 0 0.50 203 45

EL-LITEL-SPCL Special fixtures 0 0.50 203 45

EL-LITEL-SWCH Lighting contactors, photoelectric controls, low-voltage lighting controls, etc. 0 0.50 163 41




Model File Type: Lighting Plan


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

EL-LITEL-WALL Wall mounted fixtures 0 0.50 203 45

Other Discipline Information

EL-DISC-INFO Clearances and working space information (NEC code, etc.) 0 0.25 3 2




Model File Type: Power Plan


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information











Cable System

EL-CABL-TRAY EL-CABLTRM- Cable trays and wireways 0,

WIREWY0.50 203 45

Floor Information



Power

EL-POWR-BUSW Busways 0,

BUSWAY0.50 203 45

EL-POWR-CIRC Power circuits (including crosslines and homeruns) V 0.50 83 42

EL-POWR-CIRC-NUMB

Power circuit numbers (e.g., panel/circuit number, wire/conduit size) 0 0.35 2 4

EL-POWR-CLNG Ceiling outlets (receptacles and switches) 0 0.50 83 42

EL-POWR-FEED Feeders 0 0.50 203 45

EL-POWR-GENR Generators and auxiliary equipment 0 0.50 4 7

EL-POWR-JBOX Junction boxes, pull boxes, manholes, handholes, pedestals, splices 0 0.50 83 42

EL-POWR-MOTR Motors and utilization equipment 0 0.50 4 7




Model File Type: Power Plan


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

EL-POWR-PANL Panelboards, switchboards, MCC, unit substations, backing boards, patch panel 0 0.50 4 7

EL-POWR-SWCH Fuse cutouts, motor starters, contactors, pole mounted switches, circuit breakers,

gang operated disconnects, reclosers, cubicle switches 0 0.50 163 41

EL-POWR-URAC Underfloor raceways 3 0.50 203 45

EL-POWR-WALL Wall/floor outlets (receptacles and switches) 0 0.50 83 42






Model File Type: Special Systems Plan


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information











Alarm System

EL-ALRM-EQPM Alarm system equipment 0 0.50 203 45

EL-ALRM-IDEN Identifier tags, symbol modifiers, and text 0 0.35 2 4

Bell System

EL-BELL-EQPM Bell system equipment 0 0.50 203 45

EL-BELL-IDEN Identifier tags, symbol modifiers, and text 0 0.35 2 4

Cable System

EL-CABL-COAX Coax cable 2 0.50 83 42

EL-CABL-FIBR Fiber optics cable FIBOPT 0.50 83 42

EL-CABL-IDEN Identifier tags, symbol modifiers, and text 0 0.35 2 4

EL-CABL-MULT Multi-conductor cable V 0.50 83 42

EL-CABL-TRAY EL-CABLTRM- Cable trays and wireways 0,

WIREWY0.50 203 45

Cable TV System

EL-CATV-EQPM Cable TV system equipment 0,

CABLTV0.50 203 45

EL-CATV-IDEN Identifier tags, symbol modifiers, and text 0 0.35 2 4

Closed-Circuit Television System

EL-CCTV-EQPM Closed-circuit television system equipment 0 0.50 203 45






Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

EL-CCTV-IDEN Identifier tags, symbol modifiers, and text 0 0.35 2 4

Clock System

EL-CLOK-EQPM Clock system equipment 0 0.50 203 45

EL-CLOK-IDEN Identifier tags, symbol modifiers, and text 0 0.35 2 4

Central Dictation System

EL-DICT-EQPM Central dictation system equipment 0 0.50 203 45

EL-DICT-IDEN Identifier tags, symbol modifiers, and text 0 0.35 2 4

Energy Monitoring Control Systems

EL-EMCS-EQPM Energy monitoring control system equipment 0 0.50 203 45

EL-EMCS-IDEN Identifier tags, symbol modifiers, and text 0 0.35 2 4

Floor Information



Intercom System

E-INTC-EQPM Intercom system equipment 0 0.50 203 45

E-INTC-IDEN Identifier tags, symbol modifiers, and text 0 0.35 2 4

Nurse Call/ Paging System

EL-NURS-EQPM Nurse call/paging system equipment 0 0.50 203 45

EL-NURS-IDEN Identifier tags, symbol modifiers, and text 0 0.35 2 4

Power


EL-POWR-PANL Panelboards, switchboards, MCC, unit substations, backing boards, patch panel 0 0.50 4 7

Security System

EL-SERT-ACCS Access control system 0 0.50 23 46

EL-SERT-CLNG Ceiling mounted sensors 0 0.50 23 46

EL-SERT-FLOR Floor mounted sensors 0 0.50 23 46

EL-SERT-IDEN Identifier tags, symbol modifiers, and text 0 0.35 2 4






Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

EL-SERT-UNDR Buried sensors 0 0.50 23 46

EL-SERT-WALL Wall mounted sensors 0 0.50 23 46

Sound/PA System

EL-SOUN-EQPM Sound/PA system equipment 0 0.50 203 45

EL-SOUN-IDEN Identifier tags, symbol modifiers, and text 0 0.35 2 4

TV Antenna System

EL-TVAN-EQPM Television antenna system equipment 0 0.50 203 45

EL-TVAN-IDEN Identifier tags, symbol modifiers, and text 0 0.35 2 4






Model File Type: Grounding System Plan


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information











Ground System

EL-GRND-CIRC Circuits 0 0.50 4 7

EL-GRND-DIAG Ground system diagram 0 0.50 163 41

EL-GRND-EQUI Equipotential ground system 0 0.50 83 42

EL-GRND-REFR Reference ground system 0 0.50 23 46

Lighting Protection System

EL-LTNG-COND Lightning protection conductors 0 0.50 203 45 0 0.50 203 45

EL-LTNG-TERM Lightning protection terminals 0 0.35 2 4




Model File Type: Electrical Utilities Plan


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information











Cathodic Protection System

EL-CATH-ANOD Sacrificial anode system 0 0.05 83 42

EL-CATH-CURR Impress current system 0 0.50 83 42

EL-CATH-IDEN Identifier tags, symbol modifier, and text 0 0.35 83 42

EL-CATH-TEST Test stations 0 0.50 83 42

Underground Ductbanks (to be used when multiple systems are in one ductbank system)

EL-DUCT-MULT Ductbank EUDUCN 0.50 83 42

EL-DUCT-MULT-IDEN Identifier tags, symbol modifier and text 0 0.35 83 42

Lighting

EL-LITE-EXTR Exterior lights 0 0.50 203 45

EL-LITE-EXTR-IDEN Exterior light identifier tags, symbol modifiers, and text 0 0.35 203 45

Power

EL-POWR-DEVC Capacitors, voltage regulators, motors, buses, generators, meters, grounds 0 0.50 23 46


EL-POWR-POLE Power poles 0 0.50 203 45

EL-POWR-POLE-GUYS Guying equipment 0 0.50 203 45

EL-POWR-POLE-IDEN Identifier tags, symbol modifiers, and text 0 0.35 203 45




Model File Type: Electrical Utilities Plan


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

EL-POWR-SUBS Other substation equipment 0 0.50 23 46

EL-POWR-SWCH Fuse cutouts, motor starters, contactors, pole mounted switches, circuit breakers, gang operated disconnects, reclosers, cubicle switches

0 0.50 163 41

EL-POWR-XFMR-PADM Pad mounted transformers 0 0.50 23 46

EL-POWR-XFMR-POLM Pole mounted transformers 0 0.50 23 46

Primary Electrical Cables

EL-PRIM-OVHD Overhead electrical utility lines EPARN 0.50 4 7

EV-PRIM-OVHD-IDEN Identifier tags, symbol modifiers, and text 0 0.35 4 7

EV-PRIM-UNDR Underground electrical utility lines EPUGN 0.50 4 7

EL-PRIM-UNDR-IDEN Identifier tags, symbol modifiers, and text 0 0.35 4 7

Secondary Electrical Cables

EL-SECD-OVHD Overhead electrical utility lines ESARN 0.50 163 41

EL-SECD-OVHD-IDEN Identifier tags, symbol modifiers, and text 0 0.35 163 41

EL-SECD-UNDR Underground electrical utility lines ESUGN 0.50 163 41

EL-SECD-UNDR-IDEN Identifier tags, symbol modifiers, and text 0 0.35 163 41

Special Systems

EL-SPCL-SYST Special systems (UMCS, EMCS, CATV, etc.) 0 0.50 203 45

EL-SPCL-SYST-IDEN Special systems (UMCS, EMCS, CATV, etc.) identifier tags, symbol modifier, and text 0 0.35 203 45

EL-SPCL-TRAF Traffic signal system 0 0.50 203 45

EL-SPCL-TRAF-IDEN Traffic signal identifier tags, symbol modifier, and text 0 0.35 203 45






Model File Type: Exterior Communication Systems Plan


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information











Communications

EL-COMM-EQPM Other communications distribution equipment 0 0.50 23 46

EL-COMM-JBOX Communication junction boxes, pull boxes, manholes, handholes, pedestals, and s 0 0.50 23 46

EL-COMM-OVHD Overhead communications/telephone lines COMARN 0.50 4 7

EL-COMM-OVHD-IDEN Identifier tags, symbol modifier and text 0 0.35 4 7

EL-COMM-POLE Poles 0 0.50 203 45

EL-COMM-POLE-GUYS Guying equipment 0 0.50 203 45

EL-COMM-POLE-IDEN Identifier tags, symbol modifiers, and text 0 0.35 203 45

EL-COMM-UNDR Underground communications/telephone lines COMUGN 0.50 4 7

EL-COMM-UNDR-IDEN Identifier tags, symbol modifier and text 0 0.35 4 7

Underground Ductbanks (to be used when multiple systems are in one ductbank system)

EL-DUCT-MULT Ductbank EUDUCN 0.50 83 42

EL-DUCT-MULT-IDEN Identifier tags, symbol modifier and text 0 0.35 83 42






Model File Type: Airfield Lighting Plan


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information











Airfields

EL-AFLD-BCNS-IDEN Identifier tags, symbol modifiers, and text 0 0.35 203 45

EL-AFLD-BCNS-MISC Miscellaneous navaids - windcones and beacons 0 0.50 203 45

EL-AFLD-BCNS-STRB Strobe beacons 0 0.50 203 45

EL-AFLD-CIRC-CTRL Control and monitoring circuits 0 0.50 163 41

EL-AFLD-CIRC-IDEN Circuit identifier tags, symbol modifier, and text 0 0.35 2 4

EL-AFLD-CIRC-MULT Multiple circuits 0 0.50 23 46

EL-AFLD-CIRC-SERS Series circuits 0 0.50 203 45

EL-AFLD-DEVC Capacitors, voltage regulators, motors, buses, generators, meters, grounds 0 0.50 23 46

EL-AFLD-DUCT Ductbanks EUDUCN 0 0.50 83 42

EL-AFLD-JBOX Junction boxes, pull boxes, manholes, handholes, pedestals, splices 0 0.50 23 46

EL-AFLD-LITE-APPR Approach lights 0 0.50 203 45

EL-AFLD-LITE-DIST Distance and arresting gear markers 0 0.50 203 45

EL-AFLD-LITE-LANE Hoverlane, taxilane, and helipad lights 0 0.50 203 45

EL-AFLD-LITE-OBST Obstruction lights 0 0.50 203 45

EL-AFLD-LITE-RUNW Runway lights 0 0.50 203 45

EL-AFLD-LITE-SIGN Taxiway guidance signs 0 0.50 203 45

EL-AFLD-LITE-TAXI Taxiway lights 0 0.50 203 45




Model File Type: Airfield Lighting Plan


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

EL-AFLD-LITE-THRS Threshold lights 0 0.50 203 45

EL-AFLD-VALT Airfield lighting vaults 0 0.50 203 45








Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information













Detail Information

EL-DETL-GRPH Graphics, gridlines, non-text items V V V V

EL-DETL-INPD Inch-pound specific dimensions and notes 0 0.35 2 4

EL-DETL-METR Metric specific dimensions and notes 0 0.35 2 4




Model File Type: Riser/One-Line Diagrams


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information













Diagram Information

EL-DIAG-GRPH Graphics, gridlines, non-text items V V V V

EL-DIAG-IDEN Metric specific dimensions and notes 0 0.35 2 4

EL-DIAG-INPD Inch-pound specific dimensions and notes 0 0.35 2 4

EL-DIAG-METR Metric specific dimensions and notes 0 0.35 2 4



4.18 Communications

TABLE I-4-91 Discipline: Communications



Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information

CO-ANNO-DIMS Witness extension lines, dimensions arrowheads and text 0 V V V

CO-ANNO-KEYN Keynote with associated leaderlines and arrowheads 0 V V V

CO-ANNO-NPLT Construction lines, reference targets, area calculations V 0 5 1

CO-ANNO-PATT Miscellaneous patterning 0 0 8 9

CO-ANNO-NOTE General note and general remarks 0 2 2 4

CO-ANNO-SYMB Reference bubbles, matchlines, breaklines V 2 6 5

CO-ANNO-TEXT Detail title text, leaderlines, arrowheads, notes 0 V V V

CO-STAT-DEMO Demolition 2 2 6 5

CO-STAT-EXST Existing to remain 0 1 3 2

CO-STAT-MOVE Items to be moved 5 2 6 5

CO-STAT-NICN Not in contract 3 0 8 9

CO-STAT-PHS# Phase numbers (# = 1-9) 0 2 2 4

CO-STAT-RELO Relocated items 2 0 5 1

CO-STAT-TEMP Temporary work 4 3 4 7

CO-DEMO-HAZW Hazardous waste 0 2 6 5




Model File Type: Telephone/Data Plan


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information

CO-ANNO-DIMS Witness/extension lines, dimension terminators, dimension text 0 V V V

CO-ANNO-KEYN Reference keynotes with associated leaders 0 V V V

CO-ANNO-NOTE General notes and general remarks 0 0.35 2 4

CO-ANNO-NPLT Non-plotting graphic information 0 0.18 5 1

CO-ANNO-PATT Patterning, poche, shading, and hatching V 0.18 8 9

CO-ANNO-RDME Read-me information 0 0.18 5 1

CO-ANNO-REFR Reference files (AutoCAD users only) NA NA NA NA

CO-ANNO-SYMB Miscellaneous symbols V V 6 5

CO-ANNO-TEXT Miscellaneous text and callouts with associated leaders 0 V V V

Cable System

CO-CABL-COAX Coax cable 2 0.50 83 42

CO-CABL-FIBR Fiber optics cable FIBOPT 0.50 83 42

CO-CABL-IDEN Cable identifiers 0 0.35 2 4

CO-CABL-MULT Multi-conductor cable 0 0.50 83 42

CO-CABL-TRAY Cable trays and wireways 0 0.50 203 45

Equipment

CO-EQPM-COMB Distribution equipment for both copper and fiber optics 0 0.50 4 7

CO-EQPM-COPP Distribution equipment for copper 0 0.50 4 7

CO-EQPM-FIBR Distribution equipment for fiber optic 0 0.50 4 7

CO-EQPM-OTHR Other telecommunications equipment 0 0.50 4 7

CO-EQPM-RELA Relays, resistors, capacitors, and inducers 0 0.50 4 7

Floor Information

CO-FLOR-IDEN Room name, space identification text (copied from Architectural - Floor Plan model file 0 0.25 3 2

CO-FLOR-NUMB Room/space identification number and symbol (copied from Architectural – Floor Plan model file) 0 0.25 3 2

Jacks

CO-JACK-COMB Combination telephone and data/LAN jacks 0 0.50 203 45

CO-JACK-DATA Data/LAN jacks 0 0.50 203 45

CO-JACK-IDEN Identifier tags, symbol modifiers, and text 0 0.35 2 4




Model File Type: Telephone/Data Plan


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

CO-JACK-PHON Telephone jacks 0 0.50 203 45

Junction Boxes

CO-COMM-JBOX Junction boxes 0 0.50 83 42


CO-DISC-INFO Information and notes for other disciplines V V V V






Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information











CO-DISC-INFO Information and notes for other disciplines V V V V

Diagram Information

CO-DIAG-GRPH Graphics, gridlines, non-text items V V V V

CO-DIAG-IDEN Identifier tags, symbol modifiers, and text 0 0.35 2 4

CO-DIAG-INPD Inch-pound specific dimensions and notes 0 0.35 2 4

CO-DIAG-METR Metric specific dimensions and notes 0 0.35 2 4






Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information










Detail Information

CO-DETL-GRPH Graphics, gridlines, non-text items V V V V

CO-DETL-INPD Inch-pound specific dimensions and notes V V V V

CO-DETL-METR Metric specific dimensions and notes V V V V



4.19 Baggage Handling System

TABLE I-4-95 Discipline: Baggage Handling System



Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information

BG-ANNO-DIMS Witness extension lines, dimensions arrowheads and text 0 V V V

BG-ANNO-KEYN Keynote with associated leaderlines and arrowheads 0 V V V

BG-ANNO-NPLT Construction lines, reference targets, area calculations V 0 5 1

BG-ANNO-PATT Miscellaneous patterning 0 0 8 9

BG-ANNO-NOTE General note and general remarks 0 2 2 4

BG-ANNO-SYMB Reference bubbles, matchlines, breaklines V 2 6 5

BG-ANNO-TEXT Detail title text, leaderlines, arrowheads, notes 0 V V V

BG-STAT-DEMO Demolition 2 2 6 5

BG-STAT-EXST Existing to remain 0 1 3 2

BG-STAT-MOVE Items to be moved 5 2 6 5

BG-STAT-NICN Not in contract 3 0 8 9

BG-STAT-PHS# Phase numbers (# = 1-9) 0 2 2 4

BG-STAT-RELO Relocated items 2 0 5 1

BG-STAT-TEMP Temporary work 4 3 4 7

BG-DEMO-HAZW Hazardous waste 0 2 6 5



TABLE I-4-96 Discipline: Baggage Handling

Model File Type: Baggage Handling Plan


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information

BG-ANNO-DIMS Witness/extension lines, dimension terminators, dimension text 0 V 1 3

BG-ANNO-KEYN Reference keynotes with associated leaders 0 V 4 7

BG-ANNO-NPLT Non-plotting information 0 0.18 V V

BG-ANNO-PATT Miscellaneous patterning and hatching 0 0.18 10 10

BG-ANNO-NOTE General note and general remarks 0 0.35 4 7

BG-ANNO-SYMB Miscellaneous symbols 0 0.35 4 7

BG-ANNO-LEAD Leaders 0 0.25 4 7

BG-ANNO-TEXT Miscellaneous text and callouts with associated leaders 0 V 4 7

BG-ANNO-REFR Reference files N/A N/A N/A N/A

Conveyor

BG-CLMU-XXX-EXST Existing claim devices to remain 0 V V V

BG-CLMU-XXX-PHS# New claim devices installed in phase # 0 V V V

BG-CONV-XXX-EXST1 Existing conveyor subsystem XXX to remain on baggage claim level 0 V V V

BG-CONV-XXX-EXST2 Existing conveyor subsystem XXX to remain on concourse level 0 V V V

BG-CONV-XXX-EXST3 Existing conveyor subsystem XXX to remain on ticketing/ check-in level 0 V V V

BG-CONV-XXX-PHS# New conveyor subsystem XXX installed in phase # 0 V V V

BG-MKUP-XXX-EXST Existing make-up devices to remain 0 V V V

BG-MKUP-XXX-PHS# New make-up devices installed in phase # 0 V V V

BG-CONV-EQUIP-ATR-PHS# Automatic Tag readers 1 V V V

BG-CONV-EQUIP-BMA-PHS# Baggage Measurement Arrays 2 V V V

BG-CONV-EQUIP-VDT-PHS# Vertical diverter 2 V V V

BG-CONV-FLOW Baggage Flow arrows 3 V V V

BG-CONV-BAG CLEAR Three foot clear above conveyor belt 4 V V V

BG-CONV-INFO-XXX Clearances, working spaces and top of belts*(TOB) 5 V V V

Controls and Motor Control Panels






Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

BG-CTRL-XXX-EXST1 Existing controls on subsystem XXX to remain on the baggage claim level 0 0.25 2 4

BG-CTRL-XXX-EXST2 Existing controls on subsystem XXX to remain on the concourse level 0 0.25 2 4

BG-CTRL-XXX-EXST3 Existing controls on subsystem XXX to remain on the ticketing/check-in level 0 0.25 2 4

BG-CTRL-XXX-PHS# New controls installed on subsystem XXX in phase # 0 0.25 1 3

BG-MCPL-XXX-EXST Existing Motor Control Panels on subsystem XXX to remain 0 V V V

BG-MCPL-XXX-PHS# New Motor Control Panels on subsystem XXX installed in phase # 0 V V V

TSA Entities

BG-TEDS-XXX-EXST Existing TSA Explosive Detection Device (EDS) along subsystem XXX to remain 0 V V V

BG-TEDS-XXX-PHS# New TSA Explosive Detection Device (EDS) along subsystem XXX installed in phase # 0 V V V

BG-TETD-XXX-EXST Existing Explosive Trace Device (ETD) along subsystem XXX to remain 0 V V V

BG-TETD-XXX-PHS# New Explosive Trace Device (ETD) along subsystem XXX installed in phase # 0 V V V

BG-TOSR-EXST Existing On Screen Resolution (OSR) to remain 0 V V V

BG-TOSR-PHS# New On Screen Resolution (OSR) installed in phase # 0 V V V

Fire System

BG-SFDR-XXX-EXST Existing security/fire door (SFD) along subsystem XXX to remain 0 V 2 4

BG-SFDR-XXX-PHS# New security/fire door (SFD) along subsystem XXX installed in phase # 0 V 1 3

Relocation

BG-CLMU-XXX-MOVE Claim device XX relocation 0 V V V

BG-CONV-XXX-MOVE Conveyor from existing subsystem relocated within facility 0 V V V

BG-TEDS-XXX-MOVE EDS from existing subsystem XXX relocated within facility 0 V V V

BG-TETD-XXX-MOVE ETD from existing subsystem XXX relocated within facility 0 V V V

BG-MCPL-XXX-MOVE MCP from existing subsystem XXX relocated within facility 0 V V V

BG-MKUP-XXX-MOVE Existing MKUP XX relocated within facility 0 V V V

BG-TOSR-MOVE Existing OSR equipment relocated within facility 0 V V V






Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

BG-SFDR-XXX-MOVE Existing security/fire door relocated within facility 0 V V V

Demolition

BG-CTWK-DEMO-PHS# Demolition of existing catwalk - phase # V V 5 1

BG-CLMU-XXX-DEMO-PHS# Demolition of existing claim device XX - phase # V V V V

BG-CONV-XXX-DEMO-PHS# Demolition of existing conveyor XXX - phase # V V V V

BG-TEDS-XXX-DEMO-PHS# Demolition of existing EDS along subsystem XXX - phase # V V V V

BG-TETD-XXX-DEMO-PHS# Demolition of existing ETD along subsystem XXX - phase # V V V V

BG-MCPL-XXX-DEMO-PHS# Demolition of existing MCP for subsystem XXX - phase # V V V V

BG-MKUP-XXX-DEMO-PHS# Demolition of existing make up device XX - phase # V V V V

BG-SFDR-XXX-DEMO-PHS#

Demolition of existing security/fire door along subsystem XXX - phase # V V 5 1

Temporary Work

BG-CTWK-TEMP-PHS# Temporary catwalk to be installed in phase # V V 5 1

BG-CONV-XXX-TEMP-PHS# Temporary conveyor XXX to be installed in phase # V V V V

BG-TEDS-XXX-TEMP-PHS#

Temporary EDS along subsystem XXX to be installed in phase # V V V V

BG-TETD-XXX-TEMP-PHS# Temporary ETD along subsystem XXX to be installed in phase # V V 5 1

BG-MKUP-XXX-TEMP-PHS# Temporary make-up XX to be installed in phase # V V V V

Staging

BG-CART-EXIST Existing cart staging arrangement 0 0.25 2 4

BG-CART-PHS# New cart staging arrangement in phase # 0 0.25 1 3

Access

BG-CTWK-EXST Existing catwalk to remain 0 0.35 2 4

BG-CTWK-PHS# New catwalk installed in phase # 0 0.35 1 3






Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

BG-CTWK-DEMO Catwalk demolition 0 V V V


BG-DISC-INFO Clearances, working spaces and top of bed heights (TOB) 0 0.35 4 7



4.20 Security & Access Control System

TABLE I-4-97 Discipline: Security & Access Control System

Model File Type: Demolition


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information

SS-ANNO-DIMS Witness/extension lines, dimensions, arrowheads and text 0 0 7 0

SS-ANNO-KEYN Keynotes with associated leader lines and arrowheads 0 0 7 0

SS-ANNO-NPLT Construction lines, reference targets, area calculators 0 1 5 1

SS-ANNO-PATT Miscellaneous patterning 0 0 8 9

SS-ANNO-NOTE General notes and general remarks 0 2 2 4

SS-ANNO-SYMB Reference bubbles V 2 6 5

SS-ANNO-TEXT Detail title text, text, leader lines, arrowheads, notes 0 1 7 0

SS-ANNO-MATCH Match lines 0 5 1 3

SS-ANNO-BRK Break lines 0 0 2 4

SS-STAT-DEMO Demolition 2 2 6 5

SS-STAT-EXST Existing to remain 0 1 3 2

SS-STAT-MOVE Items to be removed 5 2 6 5

SS-STAT-NICN Not in contract 3 0 8 9

SS-STAT-PHS# Phase numbers (# =1-9) 0 2 2 4

SS-STAT-RELO Relocated items 2 0 5 1

SS-STAT-TEMP Temporary work 4 3 4 7

SS-DEMO-HAZW Hazardous waste 0 2 6 5




Model File Type: Security Plan


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information










SS-ACCS-EXTR Exterior mounted access control devices 0 1 3 2

SS-ACCS-PANL Access control unit / panel 0 1 3 2

SS-ACCS-WALL Wall mounted (interior) access control device 0 1 3 2

SS-ANCN-PANL Annunciation equipment control unit / panel 0 1 3 2

SS-ANCN-RESN Annunciation remote station 0 1 3 2

SS-BARR-FENC Fences / gates 0 2 6 5

SS-BARR-SENS Sensors 0 1 3 2

SS-BARR-WALL Walls 0 2 6 5

SS-COMM-CLNG Ceiling mounted communication equipment 0 1 3 2

SS-COMM-INTC Intercom / speakers 0 1 3 2

SS-COMM-PANL Communication panel 0 1 3 2

SS-COMM-WALL Wall mounted communication equipment 0 1 3 2

SS-SWCH-FLSH Flush mounted switches / contacts 0 1 3 2

SS-SWCH-SURF Surface mounted switches / contacts 0 1 3 2

SS-SENS-BURD Buried sensor 2 1 3 2

SS-SENS-CLNG Ceiling mounted sensor 0 1 3 2

SS-SENS-FLOR Floor mounted sensor 0 1 3 2

SS-SENS-GLAS Glass / foil mounted sensor 0 1 3 2

SS-SENS-PANL Sensor control unit 0 1 3 2

SS-SENS-WALL Wall mounted sensor 0 1 3 2

SS-CCTV-CLNG Ceiling mounted CCTV 0 1 3 2




Model File Type: Security Plan


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

SS-CCTV-WALL Wall mounted CCTV 0 1 3 2

SS-LITSC-CLNG Ceiling mounted security lighting 0 1 3 2

SS-LITSC-POLE Pole mounted security lighting 0 1 3 2

SS-LITSC-WALL Wall mounted security lighting 0 1 3 2

SS-LOCK-ELEC Electric device 0 1 3 2

SS-LOCK-MANL Manual device 0 1 3 2

SS-WIRSC-SYST Security wiring / circuits 0 0 5 1



SS-STAT-FUTR Future work 7 2 2 4











Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information










SS-CNTL-ANTA Antenna V 1 3 2

SS-CNTL-AVLV Arrestor valves V 1 3 2

SS-CNTL-BATR Batteries V 1 3 2

SS-CNTL-CAPT Capacitor V 1 3 2

SS-CNTL-CKTB Circuit boards V 1 3 2

SS-CNTL-CONT Contacts V 1 3 2

SS-CNTL-FUSE Fuses V 1 3 2

SS-CNTL-GENR Generators V 1 3 2

SS-CNTL-GRND Grounds V 1 3 2

SS-CNTL-METR Metering devices V 1 3 2

SS-CNTL-MOTR Motors V 1 3 2

SS-CNTL-OVLD Overloads V 1 3 2

SS-CNTL-RACT Reactors V 1 3 2

SS-CNTL-RELA Relays V 1 3 2

SS-CNTL-RSTR Resistors V 1 3 2

SS-CNTL-SWCH Switches V 1 3 2

SS-CNTL-XFMR Transformers V 1 3 2

SS-ALRM-DUCT Smoke detectors, heat sensors 0 1 3 2

SS-LINSC-LW18 Extra fine line work V 0 5 1

SS-LINSC-LW25 Fine line work V 1 1 3

SS-LINSC-LW35 Medium line work V 2 2 4






Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

SS-LINSC-LW50 Wide line work V 3 4 7

SS-LINSC-LW70 Extra wide line work V 4 7 0



SS-STAT-FUTR Future work 7 2 2 4






SS-DEMO-HAZW Hazardous waste 0 2 6 5






Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information


SS-ANNO-NPLT Construction lines, reference targets, area calculators V 0 5 1






SS-DETL-GENF General features (miscellaneous items) 0 V V V

SS-DETL-ARCH Architectural features 0 2 2 4

SS-DETL-BUSS Bus bars and rods 0 1 3 2

SS-DETL-CABS Cabinets and enclosures 0 2 6 5

SS-DETL-INSL Insulation and coverings 0 1 3 2

SS-DETL-LTFX Light fixtures 0 2 2 4

SS-DETL-MOTR Motors 0 1 1 3

SS-DETL-PIPE Piping and conduit 0 2 2 4

SS-DETL-STRC Structural support features 0 1 1 3

SS-DETL-TRAY Cable trays 0 2 6 5

SS-DETL-WIRE Wire and cables 0 2 2 4

SS-DETL-XFRM Transformer 0 2 2 4



4.21 Public Information System

TABLE I-4-101 Discipline: Public Information System



Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information

PS-ANNO-DIMS Witness extension lines, dimensions arrowheads and text 0 V V V

PS-ANNO-KEYN Keynote with associated leaderlines and arrowheads 0 V V V

PS-ANNO-NPLT Construction lines, reference targets, area calculations V 0 5 1

PS-ANNO-PATT Miscellaneous patterning 0 0 8 9

PS-ANNO-NOTE General note and general remarks 0 2 2 4

PS-ANNO-SYMB Reference bubbles, matchlines, breaklines V 2 6 5

PS-ANNO-TEXT Detail title text, leaderlines, arrowheads, notes 0 V V V

PS-STAT-DEMO Demolition 2 2 6 5

PS-STAT-EXST Existing to remain 0 1 3 2

PS-STAT-MOVE Items to be moved 5 2 6 5

PS-STAT-NICN Not in contract 3 0 8 9

PS-STAT-PHS# Phase numbers (# = 1-9) 0 2 2 4

PS-STAT-RELO Relocated items 2 0 5 1

PS-STAT-TEMP Temporary work 4 3 4 7

PS-DEMO-HAZW Hazardous waste 0 2 6 5




Model File Type: Public Information Systems Plan


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information

PS-ANNO-DIMS Witness extension lines, dimensions arrowheads and text 0 V V V

PS-ANNO-KEYN Keynote with associated leaderlines and arrowheads 0 V V V

PS-ANNO-NPLT Construction lines, reference targets, area calculations V 0 5 1

PS-ANNO-PATT Miscellaneous patterning 0 0 8 9

PS-ANNO-NOTE General note and general remarks 0 2 2 4

PS-ANNO-SYMB Reference bubbles, matchlines, breaklines V 2 6 5

PS-ANNO-TEXT Detail title text, leaderlines, arrowheads, notes 0 V V V

Audio Paging

PS-AUDI-DIMS Witness extension lines, dimensions arrowheads and text 0 V V V

PS-AUDI-KEYN Keynote with associated leaderlines and arrowheads 0 V V V

PS-AUDI-NPLT Construction lines, reference targets, area calculations V 0 5 1

PS-AUDI-PATT Miscellaneous patterning 0 0 8 9

PS-AUDI-NOTE General note and general remarks 0 2 2 4

PS-AUDI-SYMB Reference bubbles, matchlines, breaklines V 2 6 5

PS-AUDI-TEXT Detail title text, leaderlines, arrowheads, notes 0 V V V

Visual Paging

PS-VISU-DIMS Witness extension lines, dimensions arrowheads and text 0 V V V

PS-VISU-KEYN Keynote with associated leaderlines and arrowheads 0 V V V

PS-VISU-NPLT Construction lines, reference targets, area calculations V 0 5 1

PS-VISU-PATT Miscellaneous patterning 0 0 8 9

PS-VISU-NOTE General note and general remarks 0 2 2 4

PS-VISU-SYMB Reference bubbles, matchlines, breaklines V 2 6 5

PS-VISU-TEXT Detail title text, leaderlines, arrowheads, notes 0 V V V

Multi-User Flight Information Systems (MUFIDS)

PS-MUFIDS-DIMS Witness extension lines, dimensions arrowheads and text 0 V V V

PS-MUFIDS-KEYN Keynote with associated leaderlines and arrowheads 0 V V V

PS-MUFIDS-NPLT Construction lines, reference targets, area calculations V 0 5 1

PS-MUFIDS-PATT Miscellaneous patterning 0 0 8 9

PS-MUFIDS-NOTE General note and general remarks 0 2 2 4






Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

PS-MUFIDS-SYMB Reference bubbles, matchlines, breaklines V 2 6 5

PS-MUFIDS-TEXT Detail title text, leaderlines, arrowheads, notes 0 V V V

Baggage Information Systems (BIDS)

PS-BIDS-DIMS Witness extension lines, dimensions arrowheads and text 0 V V V

PS-BIDS-KEYN Keynote with associated leaderlines and arrowheads 0 V V V

PS-BIDS-NPLT Construction lines, reference targets, area calculations V 0 5 1

PS-BIDS-PATT Miscellaneous patterning 0 0 8 9

PS-BIDS-NOTE General note and general remarks 0 2 2 4

PS-BIDS-SYMB Reference bubbles, matchlines, breaklines V 2 6 5

PS-BIDS-TEXT Detail title text, leaderlines, arrowheads, notes 0 V V V

Flight Information Systems (FIDS)

PS-FIDS-DIMS Witness extension lines, dimensions arrowheads and text 0 V V V

PS-FIDS-KEYN Keynote with associated leaderlines and arrowheads 0 V V V

PS-FIDS-NPLT Construction lines, reference targets, area calculations V 0 5 1

PS-FIDS-PATT Miscellaneous patterning 0 0 8 9

PS-FIDS-NOTE General note and general remarks 0 2 2 4

PS-FIDS-SYMB Reference bubbles, matchlines, breaklines V 2 6 5

PS-FIDS-TEXT Detail title text, leaderlines, arrowheads, notes 0 V V V

Master Clock (MC)

PS-MC-DIMS Witness extension lines, dimensions arrowheads and text 0 V V V

PS-MC-KEYN Keynote with associated leaderlines and arrowheads 0 V V V

PS-MC-NPLT Construction lines, reference targets, area calculations V 0 5 1

PS-MC-PATT Miscellaneous patterning 0 0 8 9

PS-MC-NOTE General note and general remarks 0 2 2 4

PS-MC-SYMB Reference bubbles, matchlines, breaklines V 2 6 5

PS-MC-TEXT Detail title text, leaderlines, arrowheads, notes 0 V V V

Cable TV (CATV)

PS-CATV-DIMS Witness extension lines, dimensions arrowheads and text 0 V V V

PS-CATV-KEYN Keynote with associated leaderlines and arrowheads 0 V V V

PS-CATV-NPLT Construction lines, reference targets, area calculations V 0 5 1






Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

PS-CATV-PATT Miscellaneous patterning 0 0 8 9

PS-CATV-NOTE General note and general remarks 0 2 2 4

PS-CATV-SYMB Reference bubbles, matchlines, breaklines V 2 6 5

PS-CATV-TEXT Detail title text, leaderlines, arrowheads, notes 0 V V V

PS-STAT-DEMO Demolition 2 2 6 5

PS-STAT-EXST Existing to remain 0 1 3 2

PS-STAT-MOVE Items to be moved 5 2 6 5

PS-STAT-NICN Not in contract 3 0 8 9

PS-STAT-PHS# Phase numbers (# = 1-9) 0 2 2 4

PS-STAT-RELO Relocated items 2 0 5 1

PS-STAT-TEMP Temporary work 4 3 4 7

PS-STAT-HAZW Hazardous waste 0 2 6 5



4.22 Aviation Information System

TABLE I-4-103 Discipline: Aviation Information System



Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information

AS-ANNO-DIMS Witness extension lines, dimensions arrowheads and text 0 V V V

AS-ANNO-KEYN Keynote with associated leaderlines and arrowheads 0 V V V

AS-ANNO-NPLT Construction lines, reference targets, area calculations V 0 5 1

AS-ANNO-PATT Miscellaneous patterning 0 0 8 9

AS-ANNO-NOTE General note and general remarks 0 2 2 4

AS-ANNO-SYMB Reference bubbles, matchlines, breaklines V 2 6 5

AS-ANNO-TEXT Detail title text, leaderlines, arrowheads, notes 0 V V V

AS-STAT-DEMO Demolition 2 2 6 5

AS-STAT-EXST Existing to remain 0 1 3 2

AS-STAT-MOVE Items to be moved 5 2 6 5

AS-STAT-NICN Not in contract 3 0 8 9

AS-STAT-PHS# Phase numbers (# = 1-9) 0 2 2 4

AS-STAT-RELO Relocated items 2 0 5 1

AS-STAT-TEMP Temporary work 4 3 4 7

AS-DEMO-HAZW Hazardous waste 0 2 6 5




Model File Type: Aviation Information Systems Plan


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information

AS-ANNO-DIMS Witness extension lines, dimensions arrowheads and text 0 V V V

AS-ANNO-KEYN Keynote with associated leaderlines and arrowheads 0 V V V

AS-ANNO-NPLT Construction lines, reference targets, area calculations V 0 5 1

AS-ANNO-PATT Miscellaneous patterning 0 0 8 9

AS-ANNO-NOTE General note and general remarks 0 2 2 4

AS-ANNO-SYMB Reference bubbles, matchlines, breaklines V 2 6 5

AS-ANNO-TEXT Detail title text, leaderlines, arrowheads, notes 0 V V V

iMUSE

AS-MUSE-DIMS Witness extension lines, dimensions arrowheads and text 0 V V V

AS-MUSE-KEYN Keynote with associated leaders 0 V V V

AS-MUSE-NPLT Construction lines, reference targets, area calculations V 0 5 1

AS-MUSE-PATT Miscellaneous Patterning 0 0 8 9

AS-MUSE-NOTE General note and remarks 0 2 2 4

AS-MUSE-SYMB Reference bubbles, matchlines, breaklines V 2 6 5

AS-MUSE-TEXT Detail Title text, leaderlines, arrowheads, notes 0 V V V

Common Use Self Service (CUSS) Kiosks

AS-CUSS-DIMS Witness extension lines, dimensions arrowheads and text 0 V V V

AS-CUSS-KEYN Keynote with associated leaders 0 V V V

AS-CUSS-NPLT Construction lines, reference targets, area calculations V 0 5 1

AS-CUSS-PATT Miscellaneous Patterning 0 0 8 9

AS-CUSS-NOTE General note and remarks 0 2 2 4

AS-CUSS-SYMB Reference bubbles, matchlines, breaklines V 2 6 5

AS-CUSS-TEXT Detail Title text, leaderlines, arrowheads, notes 0 V V V

AS-STAT-DEMO Demolition 2 2 6 5

AS-STAT-EXST Existing to remain 0 1 3 2

AS-STAT-MOVE Items to be moved 5 2 6 5

AS-STAT-NICN Not in contract 3 0 8 9

AS-STAT-PHS# Phase numbers (# = 1-9) 0 2 2 4

AS-STAT-RELO Relocated items 2 0 5 1




Model File Type: Aviation Information Systems Plan


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

AS-STAT-TEMP Temporary work 4 3 4 7

AS-DEMO-HAZW Hazardous waste 0 2 6 5



4.23 Electronic Monitoring System

TABLE I-4-105 Discipline: Electronic Monitoring System



Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information

ES-ANNO-DIMS Witness extension lines, dimensions arrowheads and text 0 V V V

ES-ANNO-KEYN Keynote with associated leaderlines and arrowheads 0 V V V

ES-ANNO-NPLT Construction lines, reference targets, area calculations V 0 5 1

ES-ANNO-PATT Miscellaneous patterning 0 0 8 9

ES-ANNO-NOTE General note and general remarks 0 2 2 4

ES-ANNO-SYMB Reference bubbles, matchlines, breaklines V 2 6 5

ES-ANNO-TEXT Detail title text, leaderlines, arrowheads, notes 0 V V V

ES-STAT-DEMO Demolition 2 2 6 5

ES-STAT-EXST Existing to remain 0 1 3 2

ES-STAT-MOVE Items to be moved 5 2 6 5

ES-STAT-NICN Not in contract 3 0 8 9

ES-STAT-PHS# Phase numbers (# = 1-9) 0 2 2 4

ES-STAT-RELO Relocated items 2 0 5 1

ES-STAT-TEMP Temporary work 4 3 4 7

ES-DEMO-HAZW Hazardous waste 0 2 6 5




Model File Type: Electronic Monitoring Systems Plan


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information

ES-ANNO-DIMS Witness extension lines, dimensions arrowheads and text 0 V V V

ES-ANNO-KEYN Keynote with associated leaderlines and arrowheads 0 V V V

ES-ANNO-NPLT Construction lines, reference targets, area calculations V 0 5 1

ES-ANNO-PATT Miscellaneous patterning 0 0 8 9

ES-ANNO-NOTE General note and general remarks 0 2 2 4

ES-ANNO-SYMB Reference bubbles, matchlines, breaklines V 2 6 5

ES-ANNO-TEXT Detail title text, leaderlines, arrowheads, notes 0 V V V

Automated External Defibrillator (AED)

ES-AED –DIMS Witness/extension lines, dimensions arrowheads and text 0 V V V

ES-AED-KEYN Keynotes with associated leaders 0 V V V

ES-AED-NPLT Construction lines, reference targets, area calculations V 0 5 1

ES-AED-PATT Miscellaneous Patterning 0 0 8 9

ES-AED-NOTE General notes and remarks 0 2 2 4

ES-AED-SYMB Reference bubbles, matchlines, breaklines, equipment/devices V 2 6 5

ES-AED-TEXT Detail Title text, leaderlines, arrowheads, notes 0 V V V

Supervisory Control & Data Acquisition (SCADA)

ES-SCADA-DIMS Witness/extension lines, dimensions arrowheads and text 0 V V V

ES-SCADA-KEYN Keynotes with associated leaders 0 V V V

ES-SCADA-NPLT Construction lines, reference targets, area calculations V 0 5 1

ES-SCADA-PATT Miscellaneous Patterning 0 0 8 9

ES-SCADA-NOTE General notes and remarks 0 2 2 4

ES-SCADA-SYMB Reference bubbles, matchlines, breaklines, equipment/devices V 2 6 5

ES-SCADA-TEXT Detail Title text, leaderlines, arrowheads, notes 0 V V V

Conveyance (elevators, escalators, and moving walks)

ES-CONV Witness/extension lines, dimensions arrowheads and text 0 V V V

ES-CONV-KEYN Keynotes with associated leaders 0 V V V

ES-CONV-NPLT Construction lines, reference targets, area calculations V 0 5 1

ES-CONV-PATT Miscellaneous Patterning 0 0 8 9

ES-CONV-NOTE General notes and remarks 0 2 2 4




Model File Type: Electronic Monitoring Systems Plan


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

ES-CONV-SYMB Reference bubbles, matchlines, breaklines, equipment/devices V 2 6 5

ES-CONV-TEXT Detail Title text, leaderlines, arrowheads, notes 0 V V V

ES-STAT-DEMO Demolition 2 2 6 5

ES-STAT-EXST Existing to remain 0 1 3 2

ES-STAT-MOVE Items to be moved 5 2 6 5

ES-STAT-NICN Not in contract 3 0 8 9

ES-STAT-PHS# Phase numbers (# = 1-9) 0 2 2 4

ES-STAT-RELO Relocated items 2 0 5 1

ES-STAT-TEMP Temporary work 4 3 4 7

ES-DEMO-HAZW Hazardous waste 0 2 6 5



CHAPTER 5 Sheet File Level/Layer Assignment Tables

This chapter provides the sheet file level/layer assignment tables:

General

Hazardous Materials

Survey/Mapping

Geotechnical

Civil

Landscape

Structural Buildings

Structural Civil

Architectural

Interiors

Fire Protection

Fire Alarm System

Plumbing

Mechanical

Electrical

Communications

Baggage Handling System

Security & Access Control Systems

Security & Access Control System

Public Information Systems

Aviation Information Systems

Electronic Monitoring Systems



5.1 General



Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information

GN-ANNO-KEYN Sheet-specific reference keynotes with associated leaders 0 V V V

GN-ANNO-NPLT Legends and schedules 0 V V V

GN-ANNO-PATT Sheet-specific patterning and hatching (e.g., keyplan patterning) 0 0.18 8 9

GN-ANNO-NOTE Sheet-specific notes and general remarks 0 0.35 2 4

GN-ANNO-SYMB Sheet-specific symbols (e.g., scales, north arrow, section cuts, detail bubbles, etc.)

V 0.35 6 5

GN-ANNO-TEXT Sheet-specific text and callouts with associated leaders (e.g., title block text, legend and schedule text)

0 V V V

GN-ANNO-REDL Redlines 0 0.25 1 3

GN-ANNO-REVS Revisions 0 0.50 4 7

GN-ANNO-REFR Reference files (AutoCAD users only, refer to Chapter 4) NA NA NA NA



5.2 Hazardous Materials

TABLE I-5-2 Discipline: Hazardous Material


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information

HM-ANNO-DIMS Sheet-specific dimensions (includes withness/extension lines, dimension terminators, dimension text)

0 V V V

HM-ANNO-KEYN Sheet-specific reference keynotes with associated leaders 0 V V V

HM-ANNO-NPLT Legends and schedules 0 V V V

HM-ANNO-PATT Sheet-specific patterning and hatching (e.g., keyplan patterning) 0 0.18 8 9

HM-ANNO-NOTE Sheet-specific notes and general remarks 0 0.35 2 4

HM-ANNO-SYMB Sheet-specific symbols (e.g., scales, north arrow, section cuts, detail bubbles, etc.)

V 0.35 6 5

HM-ANNO-TEXT Sheet-specific text and callouts with associated leaders (e.g., title block text, legend and schedule text)

0 V V V

HM-ANNO-REDL Redlines 0 0.25 1 3

HM-ANNO-REVS Revisions 0 0.50 4 7

HM-ANNO-REFR Reference files (AutoCAD users only, refer to Chapter 4) NA NA NA NA



5.3 Survey/Mapping

TABLE I-5-3 Discipline: Surveying/Mapping


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information

SV-ANNO-DIMS Sheet-specific dimensions (includes withness/extension lines, dimension terminators, dimension text)

0 V V V

SV-ANNO-KEYN Sheet-specific reference keynotes with associated leaders 0 V V V

SV-ANNO-NPLT Legends and schedules 0 V V V

SV-ANNO-PATT Sheet-specific patterning and hatching (e.g., keyplan patterning) 0 0.18 8 9

SV-ANNO-NOTE Sheet-specific notes and general remarks 0 0.35 2 4

SV-ANNO-SYMB Sheet-specific symbols (e.g., scales, north arrow, section cuts, detail bubbles, etc.)

V 0.35 6 5

SV-ANNO-TEXT Sheet-specific text and callouts with associated leaders (e.g., title block text, legend and schedule text)

0 V V V

SV-ANNO-REDL Redlines 0 0.25 1 3

SV-ANNO-REVS Revisions 0 0.50 4 7

SV-ANNO-REFR Reference files (AutoCAD users only, refer to Chapter 4) NA NA NA NA



5.4 Geotechnical

TABLE I-5-4 Discipline: Geotechnical


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information

GT-ANNO-DIMS Sheet-specific dimensions (includes withness/extension lines, dimension terminators, dimension text)

0 V V V

GT-ANNO-KEYN Sheet-specific reference keynotes with associated leaders 0 V V V

GT-ANNO-NPLT Legends and schedules 0 V V V

GT-ANNO-PATT Sheet-specific patterning and hatching (e.g., keyplan patterning) 0 0.18 8 9

GT-ANNO-NOTE Sheet-specific notes and general remarks 0 0.35 2 4

GT-ANNO-SYMB Sheet-specific symbols (e.g., scales, north arrow, section cuts, detail bubbles, etc.)

V 0.35 6 5

GT-ANNO-TEXT Sheet-specific text and callouts with associated leaders (e.g., title block text, legend and schedule text)

0 V V V

GT-ANNO-REDL Redlines 0 0.25 1 3

GT-ANNO-REVS Revisions 0 0.50 4 7

GT-ANNO-REFR Reference files (AutoCAD users only, refer to Chapter 4) NA NA NA NA



5.5 Civil



Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information

CV-ANNO-DIMS Sheet-specific dimensions (includes withness/extension lines, dimension terminators, dimension text)

0 V V V

CV-ANNO-KEYN Sheet-specific reference keynotes with associated leaders 0 V V V

CV-ANNO-NPLT Legends and schedules 0 V V V

CV-ANNO-PATT Sheet-specific patterning and hatching (e.g., keyplan patterning) 0 0.18 8 9

CV-ANNO-NOTE Sheet-specific notes and general remarks 0 0.35 2 4

CV-ANNO-SYMB Sheet-specific symbols (e.g., scales, north arrow, section cuts, detail bubbles, etc.)

V 0.35 6 5

CV-ANNO-TEXT Sheet-specific text and callouts with associated leaders (e.g., title block text, legend and schedule text)

0 V V V

CV-ANNO-REDL Redlines 0 0.25 1 3

CV-ANNO-REVS Revisions 0 0.50 4 7

CV-ANNO-REFR Reference files (AutoCAD users only, refer to Chapter 4) NA NA NA NA



5.6 Landscape



Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information

LA-ANNO-DIMS Sheet-specific dimensions (includes withness/extension lines, dimension terminators, dimension text)

0 V V V

LA-ANNO-KEYN Sheet-specific reference keynotes with associated leaders 0 V V V

LA-ANNO-NPLT Legends and schedules 0 V V V

LA-ANNO-PATT Sheet-specific patterning and hatching (e.g., keyplan patterning) 0 0.18 8 9

LA-ANNO-NOTE Sheet-specific notes and general remarks 0 0.35 2 4

LA-ANNO-SYMB Sheet-specific symbols (e.g., scales, north arrow, section cuts, detail bubbles, etc.)

V 0.35 6 5

LA-ANNO-TEXT Sheet-specific text and callouts with associated leaders (e.g., title block text, legend and schedule text)

0 V V V

LA-ANNO-REDL Redlines 0 0.25 1 3

LA-ANNO-REVS Revisions 0 0.50 4 7

LA-ANNO-REFR Reference files (AutoCAD users only, refer to Chapter 4) NA NA NA NA



5.7 Structural



Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information

ST-ANNO-DIMS Sheet-specific dimensions (includes withness/extension lines, dimension terminators, dimension text)

0 V V V

ST-ANNO-KEYN Sheet-specific reference keynotes with associated leaders 0 V V V

ST-ANNO-NPLT Legends and schedules 0 V V V

ST-ANNO-PATT Sheet-specific patterning and hatching (e.g., keyplan patterning) 0 0.18 8 9

ST-ANNO-NOTE Sheet-specific notes and general remarks 0 0.35 2 4

ST-ANNO-SYMB Sheet-specific symbols (e.g., scales, north arrow, section cuts, detail bubbles, etc.)

V 0.35 6 5

ST-ANNO-TEXT Sheet-specific text and callouts with associated leaders (e.g., title block text, legend and schedule text)

0 V V V

ST-ANNO-REDL Redlines 0 0.25 1 3

ST-ANNO-REVS Revisions 0 0.50 4 7




5.8 Structural Civil



Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information

SC-ANNO-DIMS Sheet-specific dimensions (includes withness/extension lines, dimension terminators, dimension text)

0 V V V

SC-ANNO-KEYN Sheet-specific reference keynotes with associated leaders 0 V V V

SC-ANNO-NPLT Legends and schedules 0 V V V

SC-ANNO-PATT Sheet-specific patterning and hatching (e.g., keyplan patterning) 0 0.18 G8 9

SC-ANNO-NOTE Sheet-specific notes and general remarks 0 0.35 2 4

SC-ANNO-SYMB Sheet-specific symbols (e.g., scales, north arrow, section cuts, detail bubbles, etc.)

V 0.35 6 5

SC-ANNO-TEXT Sheet-specific text and callouts with associated leaders (e.g., title block text, legend and schedule text)

0 V V V

SC-ANNO-REDL Redlines 0 0.25 1 3

SC-ANNO-REVS Revisions 0 0.50 4 7




5.9 Architectural



Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information

AR-ANNO-DIMS Sheet-specific dimensions (includes withness/extension lines, dimension terminators, dimension text)

0 V V V

AR-ANNO-KEYN Sheet-specific reference keynotes with associated leaders 0 V V V

AR-ANNO-NPLT Legends and schedules 0 V V V

AR-ANNO-PATT Sheet-specific patterning and hatching (e.g., keyplan patterning) 0 0.18 8 9

AR-ANNO-NOTE Sheet-specific notes and general remarks 0 0.35 2 4

AR-ANNO-SYMB Sheet-specific symbols (e.g., scales, north arrow, section cuts, detail bubbles, etc.)

V 0.35 6 5

AR-ANNO-TEXT Sheet-specific text and callouts with associated leaders (e.g., title block text, legend and schedule text)

0 V V V

AR-ANNO-REDL Redlines 0 0.25 1 3

AR-ANNO-REVS Revisions 0 0.50 4 7

AR-ANNO-REFR Reference files (AutoCAD users only, refer to Chapter 4) NA NA NA NA



5.10 Interiors



Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information

IN-ANNO-DIMS Sheet-specific dimensions (includes withness/extension lines, dimension terminators, dimension text)

0 V V V

IN-ANNO-KEYN Sheet-specific reference keynotes with associated leaders 0 V V V

IN-ANNO-NPLT Legends and schedules 0 V V V

IN-ANNO-PATT Sheet-specific patterning and hatching (e.g., keyplan patterning) 0 0.18 8 9

IN-ANNO-NOTE Sheet-specific notes and general remarks 0 0.35 2 4

IN-ANNO-SYMB Sheet-specific symbols (e.g., scales, north arrow, section cuts, detail bubbles, etc.)

V 0.35 6 5

IN-ANNO-TEXT Sheet-specific text and callouts with associated leaders (e.g., title block text, legend and schedule text)

0 V V V

IN-ANNO-REDL Redlines 0 0.25 1 3

IN-ANNO-REVS Revisions 0 0.50 4 7

IN-ANNO-REFR Reference files (AutoCAD users only, refer to Chapter 4) NA NA NA NA



5.11 Fire Protection



Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information

FP-ANNO-DIMS Sheet-specific dimensions (includes withness/extension lines, dimension terminators, dimension text)

0 V V V

FP-ANNO-KEYN Sheet-specific reference keynotes with associated leaders 0 V V V

FP-ANNO-NPLT Legends and schedules 0 V V V

FP-ANNO-PATT Sheet-specific patterning and hatching (e.g., keyplan patterning) 0 0.18 8 9

FP-ANNO-NOTE Sheet-specific notes and general remarks 0 0.35 2 4

FP-ANNO-SYMB Sheet-specific symbols (e.g., scales, north arrow, section cuts, detail bubbles, etc.)

V 0.35 6 5

FP-ANNO-TEXT Sheet-specific text and callouts with associated leaders (e.g., title block text, legend and schedule text)

0 V V V

FP-ANNO-REDL Redlines 0 0.25 1 3

FP-ANNO-REVS Revisions 0 0.50 4 7

FP-ANNO-REFR Reference files (AutoCAD users only, refer to Chapter 4) NA NA NA NA



5.12 Fire Alarm System



Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information

FA-ANNO-DIMS Sheet-specific dimensions (includes withness/extension lines, dimension terminators, dimension text)

0 V V V

FA-ANNO-KEYN Sheet-specific reference keynotes with associated leaders 0 V V V

FA-ANNO-NPLT Legends and schedules 0 V V V

FA-ANNO-PATT Sheet-specific patterning and hatching (e.g., keyplan patterning) 0 0.18 8 9

FA-ANNO-NOTE Sheet-specific notes and general remarks 0 0.35 2 4

FA-ANNO-SYMB Sheet-specific symbols (e.g., scales, north arrow, section cuts, detail bubbles, etc.)

V 0.35 6 5

FA-ANNO-TEXT Sheet-specific text and callouts with associated leaders (e.g., title block text, legend and schedule text)

0 V V V

FA-ANNO-REDL Redlines 0 0.25 1 3

FA-ANNO-REVS Revisions 0 0.50 4 7

FA-ANNO-REFR Reference files (AutoCAD users only, refer to Chapter 4) NA NA NA NA



5.13 Plumbing



Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information

PL-ANNO-DIMS Sheet-specific dimensions (includes withness/extension lines, dimension terminators, dimension text)

0 V V V

PL-ANNO-KEYN Sheet-specific reference keynotes with associated leaders 0 V V V

PL-ANNO-NPLT Legends and schedules 0 V V V

PL-ANNO-PATT Sheet-specific patterning and hatching (e.g., keyplan patterning) 0 0.18 8 9

PL-ANNO-NOTE Sheet-specific notes and general remarks 0 0.35 2 4

PL-ANNO-SYMB Sheet-specific symbols (e.g., scales, north arrow, section cuts, detail bubbles, etc.)

V 0.35 6 5

PL-ANNO-TEXT Sheet-specific text and callouts with associated leaders (e.g., title block text, legend and schedule text)

0 V V V

PL-ANNO-REDL Redlines 0 0.25 1 3

PL-ANNO-REVS Revisions 0 0.50 4 7

PL-ANNO-REFR Reference files (AutoCAD users only, refer to Chapter 4) NA NA NA NA



5.14 Mechanical



Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information

ME-ANNO-DIMS Sheet-specific dimensions (includes withness/extension lines, dimension terminators, dimension text)

0 V V V

ME-ANNO-KEYN Sheet-specific reference keynotes with associated leaders 0 V V V

ME-ANNO-NPLT Legends and schedules 0 V V V

ME-ANNO-PATT Sheet-specific patterning and hatching (e.g., keyplan patterning) 0 0.18 8 9

ME-ANNO-NOTE Sheet-specific notes and general remarks 0 0.35 2 4

ME-ANNO-SYMB Sheet-specific symbols (e.g., scales, north arrow, section cuts, detail bubbles, etc.)

V 0.35 6 5

ME-ANNO-TEXT Sheet-specific text and callouts with associated leaders (e.g., title block text, legend and schedule text)

0 V V V

ME-ANNO-REDL Redlines 0 0.25 1 3

ME-ANNO-REVS Revisions 0 0.50 4 7

ME-ANNO-REFR Reference files (AutoCAD users only, refer to Chapter 4) NA NA NA NA



5.15 Electrical



Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information

EL-ANNO-DIMS Sheet-specific dimensions (includes withness/extension lines, dimension terminators, dimension text)

0 V V V

EL-ANNO-KEYN Sheet-specific reference keynotes with associated leaders 0 V V V

EL-ANNO-NPLT Legends and schedules 0 V V V

EL-ANNO-PATT Sheet-specific patterning and hatching (e.g., keyplan patterning) 0 0.18 8 9

EL-ANNO-NOTE Sheet-specific notes and general remarks 0 0.35 2 4

EL-ANNO-SYMB Sheet-specific symbols (e.g., scales, north arrow, section cuts, detail bubbles, etc.)

V 0.35 6 5

EL-ANNO-TEXT Sheet-specific text and callouts with associated leaders (e.g., title block text, legend and schedule text)

0 V V V

EL-ANNO-REDL Redlines 0 0.25 1 3

EL-ANNO-REVS Revisions 0 0.50 4 7

EL-ANNO-REFR Reference files (AutoCAD users only, refer to Chapter 4) NA NA NA NA



5.16 Communications



Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information

CO-ANNO-DIMS Sheet-specific dimensions (includes withness/extension lines, dimension terminators, dimension text)

0 V V V

CO-ANNO-KEYN Sheet-specific reference keynotes with associated leaders 0 V V V

CO-ANNO-NPLT Legends and schedules 0 V V V

CO-ANNO-PATT Sheet-specific patterning and hatching (e.g., keyplan patterning) 0 0.18 8 9

CO-ANNO-NOTE Sheet-specific notes and general remarks 0 0.35 2 4

CO-ANNO-SYMB Sheet-specific symbols (e.g., scales, north arrow, section cuts, detail bubbles, etc.)

V 0.35 6 5

CO-ANNO-TEXT Sheet-specific text and callouts with associated leaders (e.g., title block text, legend and schedule text)

0 V V V

CO-ANNO-REDL Redlines 0 0.25 1 3

CO-ANNO-REVS Revisions 0 0.50 4 7

CO-ANNO-REFR Reference files (AutoCAD users only, refer to Chapter 4) NA NA NA NA



5.17 Baggage Handling System

TABLE I-5-17 Discipline: Baggage Handling System


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information

BG-ANNO-DIMS Sheet-specific dimensions (includes withness/extension lines, dimension terminators, dimension text)

0 V V V

BG-ANNO-KEYN Sheet-specific reference keynotes with associated leaders 0 V V V

BG-ANNO-NPLT Legends and schedules 0 V V V

BG-ANNO-PATT Sheet-specific patterning and hatching (e.g., keyplan patterning) 0 0.18 8 9

BG-ANNO-NOTE Sheet-specific notes and general remarks 0 0.35 2 4

BG-ANNO-SYMB Sheet-specific symbols (e.g., scales, north arrow, section cuts, detail bubbles, etc.)

V 0.35 6 5

BG-ANNO-TEXT Sheet-specific text and callouts with associated leaders (e.g., title block text, legend and schedule text)

0 V V V

BG-ANNO-REDL Redlines 0 0.25 1 3

BG-ANNO-REVS Revisions 0 0.50 4 7

BG-ANNO-REFR Reference files (AutoCAD users only, refer to Chapter 4) NA NA NA NA



5.18 Security & Access Control Systems

TABLE I-5-18 Discipline: Security & Access Control Systems


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information

SS-ANNO-DIMS Sheet-specific dimensions (includes withness/extension lines, dimension terminators, dimension text)

0 V V V

SS-ANNO-KEYN Sheet-specific reference keynotes with associated leaders 0 V V V

SS-ANNO-NPLT Legends and schedules 0 V V V

SS-ANNO-PATT Sheet-specific patterning and hatching (e.g., keyplan patterning) 0 0.18 8 9

SS-ANNO-NOTE Sheet-specific notes and general remarks 0 0.35 2 4

SS-ANNO-SYMB Sheet-specific symbols (e.g., scales, north arrow, section cuts, detail bubbles, etc.)

V 0.35 6 5

SS-ANNO-TEXT Sheet-specific text and callouts with associated leaders (e.g., title block text, legend and schedule text)

0 V V V

SS-ANNO-REDL Redlines 0 0.25 1 3

SS-ANNO-REVS Revisions 0 0.50 4 7

SS-ANNO-REFR Reference files (AutoCAD users only, refer to Chapter 4) NA NA NA NA



5.19 Public Information Systems

TABLE I-5-19 Discipline: Public Information Systems


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information

PS-ANNO-DIMS Sheet-specific dimensions (includes withness/extension lines, dimension terminators, dimension text)

0 V V V

PS-ANNO-KEYN Sheet-specific reference keynotes with associated leaders 0 V V V

PS-ANNO-NPLT Legends and schedules 0 V V V

PS-ANNO-PATT Sheet-specific patterning and hatching (e.g., keyplan patterning) 0 0.18 8 9

PS-ANNO-NOTE Sheet-specific notes and general remarks 0 0.35 2 4

PS-ANNO-SYMB Sheet-specific symbols (e.g., scales, north arrow, section cuts, detail bubbles, etc.)

V 0.35 6 5

PS-ANNO-TEXT Sheet-specific text and callouts with associated leaders (e.g., title block text, legend and schedule text)

0 V V V

PS-ANNO-REDL Redlines 0 0.25 1 3

PS-ANNO-REVS Revisions 0 0.50 4 7

PS-ANNO-REFR Reference files (AutoCAD users only, refer to Chapter 4) NA NA NA NA



5.20 Aviation Information Systems

TABLE I-5-20 Discipline: Aviation Information Systems


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information

AS-ANNO-DIMS Sheet-specific dimensions (includes withness/extension lines, dimension terminators, dimension text)

0 V V V

AS-ANNO-KEYN Sheet-specific reference keynotes with associated leaders 0 V V V

AS-ANNO-NPLT Legends and schedules 0 V V V

AS-ANNO-PATT Sheet-specific patterning and hatching (e.g., keyplan patterning) 0 0.18 8 9

AS-ANNO-NOTE Sheet-specific notes and general remarks 0 0.35 2 4

AS-ANNO-SYMB Sheet-specific symbols (e.g., scales, north arrow, section cuts, detail bubbles, etc.)

V 0.35 6 5

AS-ANNO-TEXT Sheet-specific text and callouts with associated leaders (e.g., title block text, legend and schedule text)

0 V V V

AS-ANNO-REDL Redlines 0 0.25 1 3

AS-ANNO-REVS Revisions 0 0.50 4 7

AS-ANNO-REFR Reference files (AutoCAD users only, refer to Chapter 4) NA NA NA NA



5.21 Electronic Monitoring Systems

TABLE I-5-21 Discipline: Electronic Monitoring Systems


Line

Sty

le

Line

Wid

th

Aut

oCA

D C

olor

Mic

roSt

atio

n C

olor

General Information

ES-ANNO-DIMS Sheet-specific dimensions (includes withness/extension lines, dimension terminators, dimension text)

0 V V V

ES-ANNO-KEYN Sheet-specific reference keynotes with associated leaders 0 V V V

ES-ANNO-NPLT Legends and schedules 0 V V V

ES-ANNO-PATT Sheet-specific patterning and hatching (e.g., keyplan patterning) 0 0.18 8 9

ES-ANNO-NOTE Sheet-specific notes and general remarks 0 0.35 2 4

ES-ANNO-SYMB Sheet-specific symbols (e.g., scales, north arrow, section cuts, detail bubbles, etc.)

V 0.35 6 5

ES-ANNO-TEXT Sheet-specific text and callouts with associated leaders (e.g., title block text, legend and schedule text)

0 V V V

ES-ANNO-REDL Redlines 0 0.25 1 3

ES-ANNO-REVS Revisions 0 0.50 4 7

ES-ANNO-REFR Reference files (AutoCAD users only, refer to Chapter 4) NA NA NA NA



CHAPTER 6 CADD Symbols

CADD Symbols are a graphic representation of an object or of a material that represents something else. The objective of this chapter is to recommend a standardized resource to ensure consistent graphic representation in construction documents. All drawings shall be in accordance with Construction Specifications Institute (CSI), Uniform Drawing System – Module 6 Symbols. These symbols are listed by Master Format Division Number outlines below. Division 01 – General Requirements Division 02 – Existing Conditions Division 03 – Concrete Division 04 – Masonry Division 05 – Metals Division 06 – Wood, Plastics, and Composites Division 07 – Thermal and Moisture Protection Division 08 – Openings Division 09 – Finishes Division 10 – Specialties Division 11 – Equipment Division 12 – Furnishings Division 13 – Special Construction Division 21 – Fire Suppression (for Fire Protection, Fire

Alarm refer to NFPA Codes and Standards) Division 22 – Plumbing Division 23 – Heating, Ventilating, and Air Conditioning Division 25 – Integrated Automation Division 26 – Electrical Division 27 – Communications Division 28 – Electronic Safety and Security Division 31 – Earthwork Division 32 – Exterior Improvements Division 33 – Utilities Division 40 – Progress Integration Division 44 – Pollution Control Equipment



(This Page Blank)



CHAPTER 7 References and Support Files

7.1 Abbreviations

7.1.1 General: Abbreviations used shall conform to the United States National CAD Standard CSI Uniform Drawing System Module 5, “Terms and Abbreviations.” Unusual or uncommon abbreviations required on drawings, not specified by the National Standard, shall be clearly noted and defined on the G series of drawings.

7.2 Basic Electronic Layout Files

7.2.1 Bentley Microstation

FILE NAME DESCRIPTION d2234bdr.dgn Titlesheet (Ronald Reagan

Washington National Airport) 22" x 34" DCA Border Sheet

d3042bdr.dgn Titlesheet (Ronald Reagan Washington National Airport) 30" x 42" DCA Border Sheet

i2234bdr.dgn Titlesheet (Washington Dulles International Airport) 22" x 34" IAD Border Sheet

i3042bdr.dgn Titlesheet (Washington Dulles International Airport) 30" x 42" IAD Border Sheet

d2234cvr.dgn Coversheet (Ronald Reagan Washington National Airport) 22" x 34" DCA Coversheet

d3042cvr.dgn Coversheet (Ronald Reagan Washington National Airport 30" x 42" DCA Coversheet)

i2234cvr.dgn Coversheet (Washington Dulles International Airport) 22" x 34" IAD Coversheet

i3042cvr.dgn Coversheet (Washington Dulles International Airport) 30" x 42" IAD Coversheet

iprjgrid.dgn Project grid (Washington Dulles International Airport)

dprjgrid.dgn Project grid (Ronald Reagan Washington National Airport)

i2234dtl.dgn 22" x 34" Area Map Sheet (Washington Dulles International Airport)

i3042dtl.dgn 30" x 42" Area Map Sheet (Washington Dulles International Airport)

FILE NAME DESCRIPTION 8.5x11add.dgn Addenda Sheet

8.5x11Ladd.dgn Addenda Sheet (Landscape)

11x17add.dgn Addenda Sheet

11x17Ladd.dgn Addenda Sheet (Landscape)

7.2.2 Autodesk AutoCAD

FILE NAME DESCRIPTION d2234bdr.dwg Titlesheet (Ronald Reagan

Washington National Airport) 22" x 34" DCA Border Sheet

d3042bdr.dwg Titlesheet (Ronald Reagan Washington National Airport) 30" x 42" DCA Border Sheet

i2234bdr.dwg Titlesheet (Washington Dulles International Airport) 22" x 34" IAD Border Sheet

i3042bdr.dwg Titlesheet (Washington Dulles International Airport) 30" x 42" IAD Border Sheet

d22346cvr.dwg Coversheet (Ronald Reagan Washington National Airport) 22" x 34" DCA Coversheet

d3042cvr.dwg Coversheet (Ronald Reagan Washington National Airport) 30" x 42" DCA Coversheet

i2234cvr.dwg Coversheet (Washington Dulles International Airport) 22" x 34" IAD Coversheet

i3042cvr.dwg Coversheet (Washington Dulles International Airport) 30" x 42" IAD Coversheet

i2234dtl.dwg 22" x 34" Area Map Sheet (Washington Dulles International Airport)

i3042dtl.dwg 30" x 42" Area Map Sheet (Washington Dulles Internationa Airport)

iprjgrid.dwg Project grid (Washington Dulles Internationa Airport)

dprjgrid.dwg Project grid (Ronald Reagan Washington National Airport)

8.5x11add.dwg Addenda Sheet

8.5x11Ladd.dwg Addenda Sheet (Landscape)

11x17add.dwg Addenda Sheet

11x17Ladd.dwg Addenda Sheet (Landscape)



7.3 References

Tri-Service CADD/GIS Technology Center, 1999. A/E/C Standard, release 1.8, U.S. Army Engineer Research and Development Center.

American National Standards Institute (ANSI) Publications. Available from American National Standards Institute, 1430 Broadway, New York, NY 10018.

ANSI A2.4-86 Standard Symbols for Welding, Brazing and Nondestructive Examination ANSI D1.1-88 Structural Welding Code Steel ANSI Y1.1-72 Abbreviations for Use of Drawings and in Text ANSI Y14.1-80 Drawing Sheet Size and Format ANSI Y14.15-66 Electrical and Electronics Diagrams Y14.15a-71 Addenda Y14.15b-73 Interconnection Diagrams Selection 15-11, Information Sheet ANSI Y14.2M-79 Line Conventions and Lettering; Errata-1981 ANSI Y32.2.4-49 Graphical Symbols for Heating, Ventilation, and Air Conditioning ANSI Y32.2.6-50 Graphic Symbols for Heat- Power Apparatus ANSI Y32.9-72 Graphic Symbols for Electrical Wiring and Layout for Electrical Wiring and Layout Diagrams Used in Architecture and

Building Construction

American Society of Civil Engineers. 1983. “Standards and Symbols, Chapter 5,” Map Uses, Scales, and Accuracies for Engineering and Associated Purposes. Available from American Society of Civil Engineers, 345 East 47th Street, New York, NY 10017.

Compton, R. R. 1967. Manual of Field Geology, John Wiley and Sons, Ltd., New York, NY. Available from Wiley and Sons, Ltd., 605 3rd Avenue, New York, NY 10016.

Ramsey, Charles George. 1988. Architectural Graphic Standards, 6th Ed., John Wiley and Sons, Ltd., New York, NY. Available from Wiley and Sons, Ltd., 605 3rd Avenue, New York, NY 10016.

U.S. Army Corps of Engineers. 1966. “Inspection Manual for Subsurface Investigations,” North Pacific Division. Available from National Technical Information Service, 5285 Port Royal Road, Springfield, VA 22161.

U.S. Geological Survey. Undated. “Small Scale Mapping Standards and Symbols,” Reston, VA. Available form U.S. Geological Survey, National Center, 12201 Sunrise Valley, Reston, VA 22092.

U.S. Geological Survey. Undated. “Technical Standards Manual-National Mapping Division Publication No. 9.03.1,” Reston, VA. Available from U.S. Geological Survey, National Center, 12201 Sunrise Valley, Reston, VA 22092.

U.S. Army Corps of Engineers. 1990. “Engineering and Design Standards Manual for U.S. Army Corps of Engineers Computer-Aided Design and Drafting (CADD) Systems, Louisville District. Available from Information Technology Laboratory, 3909 Halls Ferry Road, Vicksburg, Mississippi 39180-6199.



CHAPTER 8 Geographic Information Systems (GIS)Standards and Submittal Requirements The Authority has established an enterprise GIS program, referred to herein as the “Authority GIS”. The Authority GIS is intended to support numerous different business processes, ranging from (and not limited to) lease and tenant management, computerized maintenance management (CMMS), landside and airside operations, public safety, master planning and environmental management.

To support these and other Authority business processes, the Authority GIS must include an accurate and complete representation of facilities and assets across both airport campuses. A key strategy for ensuring accuracy and completeness of the map (spatial) data within the Authority GIS database is to integrate data from design and construction activities, upon submittal to the Authority Program Manager by the A/E and/or contractor.

The A/E shall coordinate with the Authority to ensure that all GIS work and submittals are completed in compliance with the following:

8.1 Applicability: The A/E is required to provide a GIS submittal matching the CADD design drawings at the final design submittal milestone and, if applicable, when conformed sets are submitted following the final design submittal milestone. The contractor is required to provide a GIS submittal matching the CADD record (or, if applicable, as-built) drawings. This requirement applies to the following design and construction activities:

A. Capital Construction (CCP) design projects.

B. Capital Operations and Maintenance Improvement Program (COMIP) design projects.

C. Large tenant design projects resulting in new facilities, buildings or other structures.

D. Airline and concession tenant projects in the interior of terminals, concourses and other buildings.

8.2 Creating GIS Features from CADD Model Files: When providing a GIS submittal the A/E or contractor shall provide spatial data matching the features as rendered in the CADD drawing model files (containing the physical facility or asset components; buildings, aprons, runways, roads, fences, etc.), in real-world coordinates as further described in Section 8.3.1.

The A/E and contractor shall not create GIS submittals separately from their CADD submittals. GIS submittals shall be created by making a copy of features in the CADD model files and converting those features to GIS format, to ensure a match between the CADD and GIS submittals.

Sheet files for plotting (including borders, title blocks, etc.) shall not be included in the GIS submittal.

8.3 Structure and Organization of GIS Submittals: GIS submittals shall adhere to the following additional structural requirements and standards. Project specific requirements based on the underling standards, if any, will be provided in the contract scope of work:

8.3.1 File Format: All GIS data shall be submitted to the Authority in Environmental Systems Research Institute (ESRI) shapefile (SHP) format. One shapefile will be provided for each required GIS layer/feature class (see Section 8.3.3 below).

8.3.2 Coordinate system: All GIS data shall be submitted in Virginia State Plane feet coordinate system using North American Datum (NAD) 83 and Geographic Reference System (GRS) 80 ellipsoid. All vertical measurements in the GIS submittals should be recorded based on the North American Vertical Datum (NAVD) 88 at Dulles International Airport and the National Geodetic Vertical Datum (NGVD) 29 at Reagan National Airport.

The accompanying CADD drawings shall continue to be submitted using decimal coordinates and the Airport Coordinate System (ACS) as described in Section 2.4.3.



8.3.3 Required GIS Submittal Content: At the beginning of each design or construction project the Authority Project Manager will provide the A/E or contractor with an indication of the geographic “footprint” (or limits) for the GIS deliverable and will also indicate which layers in the Authority GIS or FAA Airports GIS Database Dictionaries (see Section 8.3.4) will be required for submittal.

8.3.4 Layer/Feature Class Assignments: GIS layers, or feature classes, are analogous to overlays in manual drafting systems and to layer/levels within a CADD drawing. Each GIS layer/feature class contains a logical grouping of features within a common feature type (e.g., buildings, roads, aprons, etc.). GIS submittals will be organized using one of two layering schemes, depending on the nature of the project and delivery milestone:

8.3.4.1 Authority GIS Database Dictionary: In all cases, the GIS submittal for final design plans shall be organized using the layers/feature classes as defined in the Authority GIS Database Dictionary (defining the layers/feature classes in the Authority GIS and the definitions indicating what features are included in each feature class).

8.3.4.2 Federal Aviation Administration (FAA) Airports GIS Database Dictionary: The Federal Aviation Administration (FAA) Advisory Circular (AC) 150/5300-18C (signed May 2009) requires submittal of spatial data for design projects paid for in part or in full by FAA Airport Improvement Program (AIP) or Passenger Facility Charge (PFC) grant funds. AC 150/5300-18 includes information on the FAA Airports GIS database dictionary.

A. For projects funded in part or in full by FAA AIP or PFC grant funds, the GIS submittal accompanying record drawings at the end of the construction phase shall be organized using the layers/feature classes as defined in the most current version of the FAA Airports GIS Database Dictionary in FAA AC 150/5300-18.

B. For projects funded in part or in full by FAA AIP or PFC grant funds, the GIS submittal shall be accompanied by a Survey Plan and Spatial Data

Collection Quality Control (QC) Plan as required by and defined within the most current version of the FAA AC 150/5300-18.

C. For projects not funded in part or in full by FAA AIP or PFC grant funds, the GIS submittal accompanying record drawings at the end of the construction phase shall be organized using the Authority GIS Database Dictionary, in a fashion similar to the GIS submittal at the final design milestone.

8.3.5 Attribution: Each feature in each layer/level of the GIS submittal will contain a number of associated attributes (stored in the ESRI shapefile). The following attributes are required as part of each GIS submittal:

A. GIS Submittals organized using the Authority GIS Database Dictionary: For all GIS submittals at the final design milestone and for GIS submittals accompanying record drawings at the end of the construction phase where no FAA submittal is required, each layer/feature class will include required attributes as per the Authority GIS Database Dictionary. The Authority GIS Database Dictionary indicates required attributes, optional attributes and in some cases valid attribute values.

B. GIS Submittals organized using the FAA Airport GIS Database Dictionary: For GIS submittals accompanying record drawings at the end of the construction phase, where FAA submittal is required, each layer/feature class will include required attributes as per the FAA Airports GIS Database Dictionary (included in the most current version of the FAA AC 150/5300-18) and a set of additional attributes from the Authority GIS Database Dictionary. The construction contract scope of work will indicate which attributes from the Authority GIS Database Dictionary shall be included in addition to FAA-required attributes.



Like the Authority GIS Database Dictionary, the FAA Airports GIS Database Dictionary indicates required and optional attributes as well as valid attribute values were appropriate.

8.3.6 Metadata: Each GIS submittal will include layer-level and feature-level metadata. The following metadata are required as part of each GIS submittal:

A. GIS Submittals organized using the Authority GIS Database Dictionary: For all GIS submittals at the final design milestone and for GIS submittals accompanying record drawings at the end of the construction phase where no FAA submittal is required, each GIS submittal layer/feature class shall include metadata as defined in the Authority GIS Metadata Specification.

B. GIS Submittals organized using the FAA Airport GIS Database Dictionary: For GIS submittals accompanying record drawings at the end of the construction phase, where FAA submittal is required, those GIS submittals will include metadata as defined in the FAA Airports GIS Database Dictionary (included in the most current version of the FAA AC 150/5300-18) and metadata as defined in the Authority GIS Metadata Specification.

8.3.7 Additional notes on Authority GIS Database Dictionary and Metadata Specification:

A. The Authority GIS Database Dictionary and Metadata Specification will be provided to the A/E and/or contractor upon contract award, and can be provided in advance of award upon request.

B. The Authority GIS Database Dictionary includes a “mapping” (association) of layer/levels in the Authority CADD Design Standard to the layer/feature classes in the Authority GIS Database Dictionary. This will assist A/Es and contractors in creating GIS submittals from CADD design drawings and record drawings.

8.4 Requirements for Ensuring High Quality GIS Deliverables This section provides a set of required practices A/Es and contractors must follow when building and preparing CADD files to facilitate GIS integration. These practices are adopted from industry best practice recommendations for ensuring proper CADD and GIS coordination and integration.

The Authority and its Program Manager reserve the right to perform quality control checks to ensure CADD content is compiled in accordance with these practices to ensure high-quality GIS deliverables.

By adhering to a set of required practices for building CADD files:

A. A/Es and contractors will find the effort to create the associated GIS deliverables will be less than that when not applying a set of required practices. Additionally, the process to convert CADD data to GIS format for delivery to the Authority will be repeatable and understandable by all stakeholders.

B. A/Es and contractors are more likely to have the Authority accept first-time CADD and GIS submittals.

C. The Authority is better assured that the GIS deliverables derived from CADD drawings contain spatial data that are properly structured and of better and more consistent quality.

8.4.1 Complex vs. Simple Geometry Types: when drafting line and polygon features in the CADD environment, those features shall be built using simple geometry types (feature shapes are determined by a set number of vertices along a line or polygon edge). An appropriate number of vertices should be placed to ensure an appropriate accuracy for the features. Exhibit I-8-1 illustrates the use of vertices to create accurate features using simple geometry types. Complex geometry types such as arcs, circles, donuts, ellipses will not be supported.



Simple Geometry Types – Using Vertices to

Accurately Portray Line or Polygon Shape Exhibit I-8-1

8.4.2 Topological Integrity: when drafting features that are connected or adjacent in the real world (such as adjacent walls, two pipes meeting at a junction, etc.) or drafting closed features (such as pavement sections, building roof-lines, or property boundaries), the features shall be drawn such that the feature endpoints or edges meet geometrically at “shared” vertices. The specific rules shall apply when drafting line features in CADD drawings:

8.4.2.1 Lines: The following practices should be observed when compiling linework in CADD model files for GIS integration:

A. Two or more line features of the same feature type (e.g., road centerline) should be “broken” to begin and end at the intersection location (i.e., two lines of the same type should not overlap), as illustrated in Exhibit I-8-2.

B. End-vertices of connecting or intersecting line segments should collated (i.e., be snapped to the same location with identical X, Y coordinates), also illustrated in Exhibit I-8-2.

Snapping End Vertices for Adjacent Line Features

Exhibit I-8-2

C. Line features should contain an appropriate number of intermediate vertices placed at intervals such that the line feature does not stray from the actual feature by more than ½ the positional accuracy limit, as shown in Exhibit I-8-1.

D. Lines should be “broken” where the characteristics of a feature changes. For example, two adjacent lines representing stormwater drainage pipes should be broken where the pipe diameter or material changes.

8.4.2.2 Polygons: The following practices should be observed when compiling polygons (areas) in CADD model files for GIS integration:

A. Polygons (or individual lines that enclose to define an area) should be closed by snapping the line endpoint vertices to an identical X, Y coordinate as shown in Exhibit I-8-3.

Polygon Closure via Collocated End Vertices

Exhibit I-8-3



B. Adjacent polygons sharing an edge must have the same collocated vertices along that edge as shown in Exhibit I-8-4. This rule applies to adjacent features of the same type (e.g., pavement sections) and adjacent features of different feature types (e.g., taxiway vs. apron).

Shared Vertices along Shared Polygon Edges

Exhibit I-8-4

C. No polygons will overlap, intersect or fall fully within another polygon of the same type (e.g., two buildings cannot overlap and a building polygon should not sit within another building polygon) unless exceptions are otherwise noted in the Authority CADD Design Standards, Authority GIS Database Dictionary or contractual documents. See Exhibit I-8-5 for example of overlapping and intersecting polygons.

Overlapping and Intersecting Polygons

Exhibit I-8-5

8.4.3 Directionality for Linework: when building a network of linear features where direction is significant (e.g., surface drainage hydrography, storm drainage network, sanitary sewer network), draw linear objects in the direction of flow.

8.4.4 Use of Custom and Continuous Linestyles: Custom and continuous line styles may both be used to depict linear features in a CADD environment. In either case, when those line features are converted to GIS format, the coordinates that define that linear feature are recognized by the GIS, not any custom line display style (such as that shown in Exhibit I-8-6 below). Therefore the linear feature will be properly represented in a GIS environment regardless of custom display styles enabled in AutoCAD or MicroStation.

8.4.5 Block and Cell Insertion Points: When converted to GIS features, AutoCAD blocks and MicroStation cells are “collapsed” to single X, Y point features at the block or cell insertion point. Therefore the insertion point of the blocks and cells must be defined in such way that is intuitive for CADD operators, but that also facilitates conversion to GIS and establishment of GIS topology. For example, an AutoCAD cell representing a manhole may be constructed as a simple open circle; in this case the cell insertion point should be in the center of the circle. In this fashion it should be intuitive to CADD technicians when placing the manhole symbol in the CADD drawing and snapping associated linework to the cell insertion point. And when the manhole feature in CADD is converted to a GIS feature, the manhole will be represented as a single X, Y coordinate at the cell insertion point. Therefore in GIS the associated lines will be properly “snapped” to the manhole point.

Exhibit I-8-6 illustrates this concept. The figure depicts two examples of a sewer pipe with a manhole at the end of the line. In both cases the insertion point of the manhole is the center of the circle. In the example on the left (Case 1 in Exhibit I-8-6) the cell insertion point is not at the end of the line, while the one on the right (case 2) shows the cell inserted at the end of the line. Since CADD block and cells are simply points in the GIS world, the insertion point of the



block will become the X, Y coordinate of the point. If the block insertion points are not “snapped” to their respective alignments, establishment of topological relationships will be difficult and significant level of effort required to process CADD data elements to associated blocks and cells with lines such that GIS topology can be established.

Snapping Line Endpoints to Cell/Block Insertion Points

Exhibit I-8-6

8.4.6 Snapping Blocks and Cells to Line Endpoints: When using AutoCAD blocks or MicroStation cells to represent real world features such as manholes, valves, or doors, associated line features should be drawn/extended to the insertion point for each cell, thereby ensuring that line endpoint vertices are collocated (identical to) the block or cell insertion point as shown in Exhibit I-8-6 above.


Aerial Photography CADD - Section II

SECTION II: Aerial Photography

CHAPTER 1 Introduction

The following standards shall be utilized when generating base map files for the Authority or an Airport Layout Plan (ALP).

DRAWING FILE NAMING CONVENTIONS

AIRPORT CODE (when four (4) digits are in Airport code - use first three) MAINTAINED/PLANNED/TEMPORARY (work in progress) USE BREAKDOWN XXXM-./DGN LA Layout CJ Contour Major CN Contour Minor VJ Vegetation Major VN Vegetation Minor AJ Access Major AN Access Minor SJ Structure Major SN Structure Minor UJ Utilities Major UN Utilities Minor WJ Water Major WN Water Minor ALP SET (Second digit to be used for additional sheets) Final Signed/Approved ALP Drawings should be locked! A1 Airport Layout Plan B1 Airport Airspace Drawing - Plan View C1 Airport Airspace Drawing - Profile View D1 Runway End Area Drawing (RPZ) E1 Terminal Area Drawing (Building Area Plan) F1 Land Use (second digit to be; E= EXISTING, F= FUTURE) G1 Airport Property Map H1 Cover Sheet EXTRA SHEETS (Second digit to be used for addition sheets) I1 Apron Utilization Plan J1 NAVAID/Data Sheet K Utilities (Second digit to be: 1 - Electrical; 2 - Water System; 3 - Sewerage; 4 - Fuel) L1 Noise Contours M1 Flight Tracks N1 Biotic Communities O1 Environmental/Wetlands P1 Taxiway Flow Diagram



Q1 Taxiway Designation Plan R1 Taxiway Designation Plan S1 Concept Alternatives T1 Staging Plan U1 - V1 - W1 - X1 - Y1 Line of Sight Drawing Z1 Shadow Diagram



LAYER/LEVEL COLORS, PEN WEIGHTS AND SCREENS

COLOR ACAD MSTATION MILS MIL LEROY SCREEN

Red 1 3 .25 10 000 None

Yellow 2 4 .50 20 1 None

Green 3 2 .30 13 00 None

Cyan 4 7 .35 15 0 None

Blue 5 1 .18 8 0000 None

Magenta 6 5 .60 25 2 None

White (Black) 7 0 .70 28 2.5 None

Gray 8 9 .80 31 3 None

Dark Red 9 10 (Lt) .25 10 000 None

Dark Yellow 10 11 (Lt) .50 20 1 65%

Dark Green 11 12 (Lt) .30 13 00 65%

Dark Cyan 12 14 (Lt) .35 15 0 65%

Dark Blue 13 6 (Orange) .18 8 0000 65%

Dark Magenta 14 13 (Lt Purple) .60 25 2 65%

Dark Gray 15 8 Black 2.00 80 7 65%

LINE TYPES

AUTOCAD USTATION

C = Continuous Line LC = 0

D1 = Dashed Line LC = 3

D2 = Dash-Dot Line LC = 4

CL = Centerline LC = 7

PH = Phantom LC = 6

HI = Hidden LC - 5



DATA SEGREGATION - BASE DATA

(ALL ELEVATIONS EXPRESSED AS ABOVE MEAN SEA LEVEL - AMSL) (ALL COLORS WILL BE DEFINED BY ENTITY)

e.g. Layer/Level Name = (M OR P)LA(NUMBER) ___LA___ LAYOUT

LAYER LEVEL ITEM(S) SYMBOL COLOR L TYPE

1 Reserved – Working -

2 Runway Endpoint Nodes, Runway Centerline, ARP Ci066/ARP White C

3 OC Listed Obstructions (Refer to List) White C

4 DOT Listed Obstructions (Refer to List) Green C

5 Control Points, Ties, Traverse & Base Lines Ci066 White C

6 Reserved

7 Reserved

8 Reserved

9 Bench Markers Ci003 Red C

10 Reserved

11 Reserved

12 Grid – Geodetic - Dk Blue C

13 Grid – State Plane - Dk Blue C

14 Grid – Airport - Dk Blue C

15 Grid – Airport Emergency Net - Dk Blue C

16 Public Land Survey/Section Corner Ci007 Red C

17 Reserved

18 Reserved

19 Boundary – Airport - White PH

20 Boundary – Government - Magenta PH

21 Boundary – Navigation Easement - White C

22 Boundary – Right-of-Way - Blue PH

23 Boundary – Leasehold - Blue PH

24 Reserved

25 Reserved

26 Runway End Area (RPZ) Outline - Yellow D2

27 Runway End Area Details - Red D1

28 Runway Visibility Zone - Red D2

29 Reserved

30 Reserved




31 Safety Area – Runway - Red PH

32 Safety Area – Taxiway - Red PH

33 Reserved

34 Reserved

36 Critical Area – ILS - Yellow HI

37 Critical Area – MLS - Yellow HI

38 Critical Area – ASR - Yellow HI

39 Critical Area – VOR/Vortac - Yellow HI

40 Clearing Limits – Light Lanes - Dk Red D2

41 Reserved

42 Reserved

43 Restriction Line – Building - Green D2

44 Restriction Line – Obstacle - Green D2

45 Restriction Line – Tail Limit (DC10, 747, Etc.) - Red D2

46 Aircraft Containment Line (Parking Limit) - Yellow D2

47 Reserved

48 Reserved

49 Reserved

50 Reserved

51 Reserved

52 Reserved

53 Reserved

54 Reserved

55 Reserved

56 Reserved

57 Reserved

58 Data Blocks, Schedules, Tables, Sheet Border, Tics, Title Block Data White C

59 Hatch, Poche Dk Red -

60 Decommissioned, Abandoned, To Be Removed Dk Blue C

61 Dimensions Blue C

62 Misc. Text Green C

63 Unidentified Features White C



(ALL ELEVATIONS EXPRESSED AS ABOVE MEAN SEA LEVEL-AMSL)

e.g. Layer/Level Name = (M or P) CJ(Number)

__CJ__ CONTOUR MAJOR


1 Reserved – Working

2 Major Index Contour & Text (Intervals = 5 feet, 10 feet, or 2 meter) - Dk Cyan C

3 Major Depression Contour and Text - Dk Green C

4 Spot Elevations Ci066 Dk Green C

5 Ridge Lines - Dk Blue C

6 Valley Drainage Flow Ci054 Dk Red C

7 Isolated Spot Elevations Ci066 Dk Green C

8 Isolated Ridge Lines - Dk Blue C

9 Isolated Valley Drainage Ci054 Dk Red C

10 Reserved

58 Data Blocks, Schedules, Tables - Green C

59 Hatch, Poche - White -

60 Decommissioned, Abandoned To Be Removed - Dk Blue C

61 Dimensions - Blue C

62 Misc. Text - Green C

63 Unidentified Features - White C




e.g. LAYER/LEVEL NAME = (M OR P) CN(NUMBER)

__CN__ CONTOUR MINOR


1-10 Previously Used


12 Intermediate Index Contour - Dk Red C

13 Intermediate Depression Contour - Dk Blue C

14 Tidal, Flat, Sand Bar Tideflat Dk Blue C

15 Rock Outcrop, Dry Wash - Dk Blue C

58 Data Blocks, Schedules, Tables, Sheet Border, Tics, Title Block Data - White C

59 Hatch, Poche - Dk Red -

60 Decommissioned, Abandoned, To Be Removed - Dk Blue C







e.g. Layer/Level Name = (M or P) WJ(Number)

__WJ__ WATER MAJOR




17 Shoreline – Ocean, Lake Pond (>100 feet width) - Green C

18 Shoreline – Canal, River, Stream (>6 feet width) - Green C

19 Reserved

20 Reserved

21 Reserved

22 Reserved

23 Reserved

58 Data Blocks, Schedules, Tales - Green C









e.g. Layer/Level Name = (M or P) WN(Number)

__WN__ WATER MINOR




25 Centerline – Canal – Stream, Ditch (<6 feet width) Ci054 Green C

26 Centerline – Intermittent/Dry Creek, Swale Ci054 Blue CL

27 Edge-Wetland, Marsh, Swamp Swamp/ Wetland Dk Green C

28 Pond or Pool (,100 feet width) - Dk Blue C

29 Isolated Centerline – Canal Stream, Ditch (<6 feet width) Ci054 Green C

30 Isolated Centerline – Intermit/Dry Creek Swale Ci054 Blue CL

31 Isolated Edge-Wetland, Marsh Swamp Swamp/ Wetland Dk Green C

32 Isolated Pond or Pool (<100 feet width) - Dk Blue C










e.g. Layer/Level Name = (M or P) VJ(Number)

__VJ__ VEGETATION MAJOR

NOTE: Bushes or Trees>10 feet (+Ten Feet) above ground are considered trees for these standards.




34 Individual Tree>100 feet Above Ground Level ShTree/ PalmTree Green C

35 Top Elevation - Red C

36 Individual Tree<100 feet Above Ground Level ShTree/ PalmTree Green C

37 Top Elevation - Red C

38 Tree Group Outline - Dk Red C

39 Outline Elev. And Spot Elev. Of Major Trees* - Dk Red C

*Place spot elevations for the 5 to 10 highest trees of the group and set elevation of outline at average elevation of group.

40 Isolated Individual Tree>100 feet Above Ground Level ShTree/ PalmTree Green C

41 Isolated Individual Tree<100 feet Above Ground Level ShTree/ PalmTree Green C

42 Isolated Tree Group Outline - Dk Red C

43 Isolated Outline Elevation and Spot Elevation of Major Trees* - Dk Red C


59 Hatch, Poche - White C



62 Misc. Text - White C

63 Unidentified Features -




e.g. Layer/Level Name = (M or P) VN(Number)

__VN__ VEGETATION MINOR

NOTE: Bushes or Trees>10 feet(+Ten Feet) above ground are considered trees for these standards.




45 Individual Bush>4 feet Above Ground Level ShTree Green C

46 Individual Bush>2 feet To <4 feet Above Ground Level ShTree (.5X) Red C

47 Bush Ground/Hedge Outline* - Dk Red C

48 Orchard Outline* - Dk Red C

49 Crop Outline Pasture, Unmowed Field Outline* - Dk Blue C

50 Landscape Area Outline* - Dk Blue C

*NOTE: PLACE ELEVATION OF OUTLINES AT TOP ELEVATION OF GROUP

51 Isolated Individual Bush>4 feet Above Ground Level ShTree (.5X) Green C

52 Isolated Individual Bush>2 to <4 feet Above Ground Level ShTree (.5X) Red C

53 Isolated Bush Group/Hedge Outline* - Dk Red C

54-57 Reserved


59 Hatch, Poche - White C




63 Unidentified Features -




e.g. Layer/Level Name = (M or P) AJ(Number)

_AJ__ ACCESS MAJOR



2 Pavement, Airfield Sod/Dirt or Water - Dk Yellow C

3 Concrete Runway - White C

4 Taxi or Apron Asphalt Runway - White C

5 Taxi or Apron Bridge-Aircraft - Green C

6 Isolated Sod/Dirt or Water TWY and Tiedown - Dk Yellow C

7 Isolated Concrete Runway, Taxiway or Apron - White C

8 Isolated Asphalt Runway, Taxiway or Apron - White C

9 Reserved

10 Pavement Roadway – Interstate, Express Way, Toll Way, US/State Hwy., and Other Arterial - Cyan C

11 Local Streets & Major Parking Areas - Cyan C

12 Bridge – Vehicle/Pedestrian - Green C

13 Restricted Access (Defined Through ALP Process) - Green C

14 Isolated Bridge Subway - Green C

15 Reserved Roadway Text - White C

16 Reserved Isolated Cur - Blue C

17 Railroad - Red D2

18 Above Ground Transport, People Mover - Green C

19 Subway - Red D2

20 Ferry Route Bus Route - Red C

21 Fence/Gate-Airfield Security (Defined in ALP Process) Fence Red C

22 Airfield Security Gate ID’s Red C

23 Reserved

24 Reserved

25-35 Reserved


59 Airfield Text - White C







e.g. Layer/Level Name = (M or P) AN(Number)

__AN__ ACCESS MINOR




37 Airfield Shoulders, Overruns, Blast Pads - Dk Green C

38 Runway Markers - Dk Red C

39 Taxiway, Apron Markings - Dk Red C

40 Isolated Airfield, Vehicle Pad - Dk Green C

41 Airfield - C

42 Vehicle Lane - Dk Red C

43 Dirt, Gravel Roads, Trails - Dk Blue C

44 Parking Lot Details - Dk Blue C

45 Sidewalks, Malls, Recreational Pavement Dk Blue

46 Guardrails – Vehicle/Pedestrian Guardrails Dk Blue C

47 Streetside, Pavement Mark - Dk Blue C

48 Isolated Parking Lot Details - Dk Blue C

49 Gate Pad Numbers - Dk Blue C

50 Gate Pad Marking - Dk Red C

51 Isolated Gate Pad Markings

52-27 Reserved

58 Data Blocks, Schedules, Tables, Sheet Border, Tics, Title Block Sata - White C









e.g. Layer/Level Name = (M or P) SJ(Number)

__SJ__ STRUCTURE MAJOR



2 Airfield: Lighting – Runway End Identified (Reil) Light Red C

3 Lighting – Approach Light Red C

4 Navigational Aids: Anemometer, Localizer, RVR, Elevation Array, Azimuth Array, Glide Slope, PAPI, VASI, ASOS, Transmission Meter

(Refer to List) Red C

5 Passenger Loading Bridge - Red C

6 Terminal AIDS-VOR, Vortac (Refer to List) Red C

7 Reserved

8 Buildings: Foundation, Footprint/Building Under Construction - Blue C

9 External Walls - Green C

10 Roofing, Ridge, Valley, Hip Line - Magenta C

11 Roof Spot Elevations - Dk Red C

12 Rooftop Features: Antenna, Satellite Dish - Red C

13 Sign, External, Features, Chimney, Coping, Façade, Parapet - Green C

14 Clock or Bell Tower, Steeple, Pole-Post, Flag, Lighting Protection - Red C

15 Dome, Dormer, Penthouse, Skylight (Outline, Peak and Ridge Line) - Yellow C

16 HVAC Equipment: (Air Handler, Cooling Tower, Etc.) - Cyan C

17 Reserved

18 Dam, Flood Control, Headwall, Culvert - Green C

19 Dock: Vehicle Loading - Red C

20 Dock: Ship, Boat and Related Equipment - Green C

21 Fence, Gate Fence Red Hi

22 Lighthouse, Silo, Smoke Stack, Bell/Clock Tower Green C Bus Shelter

23 Tank/Tower: Water, Fuel, Chemical - Green C

24 Tower: Antenna/Power Transmission - Green C

25 Tunnel, Retaining Wall - Red DI

26 Windmill, Water Though, Blast Fence - Red C

27 Isolated Dam, Flood Control, Headwall, Culvert - Green C

28 Isolated Dock: Ship, Boat and Related Equipment - Green C








62 All Text - White C





e.g. Layer/Level Name = (M or P) SN(Number)

__SN__ STRUCTURE MINOR




30 Airfield: Aircraft Outline - Cyan C

31 Airfield Signs - Blue C

32 Lighting: Runway, Taxiway, Apron Edge Light Dk Blue C

33 Lighting: Apron Security Light Red C

34 Terminal/Ground Support Equipment - Dk Blue C

35 Reserved

36 Buildings: Rooftop Features: External Stairs, Ladder, Fire Escape - Blue C

37 Fence, Guardrail Fence Red C

38 HVAC Equipment (Vent Pipe, Ventilation) - Dk Red C

39 Lightning Protection, Flag, Pool/Patio Area - Dk Blue C

40 Canopy, Carport, Porch, Shelter, Storage/Utility Shed - Red C

41 Columns, Pillars, Plaster, Flying Buttress - Blue C

42 Generator, Compressor, Chiller - Red C

43 Steps, Stairs, Fire Escape, Pedestrian Ramp - Dk Blue C

44 Terrace Outline/String - Blue C

45 Recreation and Park Area Outline - Blue C

46 Golf Course and Sports Complex/Area Outline - Blue C

47 Area Outline, Snow Dump - Blue C

48 Pole/Post, Banner, Billboards, Signs, Flag, Conveyor, Crane, External Pipe/Ductwork - Dk Blue C

49 Street, Security and Utility Lighting - Red C

50 Pool-Swimming, Fountain - Blue C

51 Traffic Control Light, Signal Equipment Shelter Light Dk Red C

52 Vehicle and Service Equipment Hoist, Gas Pump, Trash Bin, Compactor, Vacuum/Air Station - Blue C

53 Isolated Canopy, Carport, Etc. (Refer to List) Dk Blue C

54 Isolated Pole/Post, Etc. from Layer/Level 48 Buildings, Runway (Refer to List) Dk Blue C

55-57 Reserved





59 Misc. Text - Dk Red -

60 Decommissioned Abandoned, To Be Removed - Dk Blue C


62 Text - Green C





e.g. Layer/Level Name = (M or P) UJ(Number)

__UJ__ UTILITIES MAJOR ABOVE GROUND



2 Utilities Access System - Blue C

3 Electrical: Airfield Lighting Vault, Emergency Generator - Green C

4 FAA Cabling System - Red C

5 High Voltage Power Line HV Pole Red C

6 Electrical Manhole Cover Red C

7 Electrical Junction Box Cover Red C

8 HVAC: Heating, Ventilation, Air Condition - Red C

9 Isolated Heating Ventilation, Air Condition - Red C

10 Communications: FAA Cables - Red D2

11 Telephone - Red D2

12 TV, Optical Cable - Red D1

13 Communications Manhole Cover Red C

14 Water Supply: Well, Well Field, Reservoir Pumping Equipment - Blue C

15 Treatment Facility - Blue C

16 Fire Hydrant and Fire - Blue C

17 Fighting Water: Water Manhole Cover and Water Valve Box Cover Blue C

18 Sewerage: Storm Water System/Catch Basins - Red C

19 Wastewater Treatment Facility - Red C

20 Sewer Manhole Cover Red C

21 Sewer Valve Box Cover Red C

22 Fuel: Liquid Fuel Facilities: Pressure - Yellow C

23 Liquid Fuel Facilities: Gravity - Yellow C

24 Hydrant Fueling System - Yellow C

25 Gaseous Fuel Facilities (Propane, Natural) - Yellow C

26 Fueling Manhole Cover Yellow C

27 Fuel Pit Cover Yellow C







e.g. Layer/Level Name = (M or P) UN(Number)

__UN__ UTILITIES MINOR BELOW GROUND




31 Utilities Access System - Blue C

32 Electrical: Airfield Lighting Vault, Emergency Generator - Green C

33 FAA Cabling System - Red C

34 Low Voltage Power Line LV Pole Blue C

35 High Voltage Power Line HV Pole Red C

36 HVAC: Heating, Ventilation, Air Condition - Red C

37 Isolated Heating Ventilation, Air Condition - Red C

38 Communications: FAA Cables - Red D2

39 Telephone - Red D2

40 TV, Optical Cable - Red D1

41 Reserved

42 Reserved

42 Water Supply: Reservoir Pumping Equipment - Red C

44 Fire Hydrant and Fire Fighting Water - Red C

45 Reserved

46 Sewerage: Storm Water System/Catch Basins - Red C

47 Wastewater System - Red C

48 Reserved

49 Reserved

50 Fuel: Liquid Fuel Facilities: Pressure - Red C

51 Liquid Fuel Facilities: Gravity - Red C

52 Hydrant Fueling System - Red C

53 Gaseous Fuel Facilities (Propane, Natural) - Red C

54 Reserved





CADD - List of Exhibits

LIST OF EXHIBITS

SECTION I: CADD Standards .............................................................................................................................................. 13

CHAPTER 2 General Standards........................................................................................................................................... 15

Exhibit I-2-1 IAD Project Grid ............................................................................................................................. 17 Exhibit I-2-2 DCA project grid ............................................................................................................................. 18

CHAPTER 3 Drawing File Information................................................................................................................................. 33

Exhibit I-3-1 Model File Naming Convention ...................................................................................................... 34 Exhibit I-3-2 Sheet File Naming Convention....................................................................................................... 35 Exhibit I-3-3 Addendum File Naming Convention.............................................................................................. 36 Exhibit I-3-4 Authority Standard Drawing Sheet Titleblock For IAD ................................................................... 37 Exhibit I-3-5 Authority Standard Cover Sheet For IAD ....................................................................................... 38 Exhibit I-3-6 Authority Enlarged Plan Sheet For IAD.......................................................................................... 39 Exhibit I-3-7 Authority Standard Drawing Sheet Titleblock For DCA.................................................................. 40 Exhibit I-3-8 Authority Standard Cover Sheet For DCA...................................................................................... 41 Exhibit I-3-9 Authority Standard Addenda or Sketches Sheet............................................................................ 42

CHAPTER 8 Geographic Information Systems (GIS)Standards and Submittal Requirements ................................... 285

Exhibit I-8-1 Simple Geometry Types – Using Vertices to Accurately Portray Line or Polygon Shape............ 288 Exhibit I-8-2 Snapping End Vertices for Adjacent Line Features...................................................................... 288 Exhibit I-8-3 Polygon Closure via Collocated End Vertices .............................................................................. 288 Exhibit I-8-4 Shared Vertices along Shared Polygon Edges ............................................................................ 289 Exhibit I-8-5 Overlapping and Intersecting Polygons........................................................................................ 289 Exhibit I-8-6 Snapping Line Endpoints to Cell/Block Insertion Points............................................................... 290


CADD - List of Exhibits

(This Page Blank)


CADD - Index

INDEX

Note: Page numbers followed by e or t indicate Exhibits and Tables, respectively.

A abbreviations for references and support files, 283 access. See also security and access control systems

baggage handling system, 241–242t structural buildings, 140t, 143t structural civil, 151t, 154t, 156t

ACS (Airport Coordinate System), 16 Addenda Sheet, 42e addenda sketches, 33 addendum files, naming conventions, 36e AED (automated external defibrillator), 257t aerial photography

colors, pen weights and screens, 293t data segregation-base data

Access Major, 302–303t Access Minor, 304t Contour Major, 296t Contour Minor, 297t Layout, 294–295t Structure Major, 305–306t Structure Minor, 307–308t utilities major above ground, 309–310t utilities minor below ground, 311–312t Vegetation Major, 300t Vegetation Minor, 301t Water Major, 298t Water Minor, 299t

drawing file naming conventions, 291–292 line types, 293t

airfield lighting plan, 51t, 53, 229–230t airfield plan, 105–108t airfield traffic areas

airfield plan, 108t Airport Coordinate System (ACS), 16 airport grid file, global origin on, 16 Airport Layout Plan (ALP), 291 alignments

airfield plan, 105t block and cell insertion points, 290 eco-restoration plan, 77t flood control plan, 91t grading plan, 74t navigation dredging plan, 84t profiles

civil drawings, 115t shore bankline, 80t site plan, 63t transportation site plan, 101t utilities plan, 109t

ALP (Airport Layout Plan), 291 annotation levels/layers, 27, 29

anti-freeze, 205t aprons, 285, 286, 289

airfield plan, 105–106t profiles

civil drawings, 115t X-sections

civil drawings, 122t aqueous film forming foam system, 185t architectural drawings

area calculations/occupancy plan, 169t demolition plan, 163t details, 172t elevations, 170t equipment plan, 168t floor plan, 164–165t numbering and organization of, 45t reflected ceiling plan, 166t roof plan, 167t sections, 230t sheet level/layer assignments, 268t

area calculations, 169t arrow, north, orientation of, 24 assignment tables. See level/layer assignments (model

files); level/layer assignments (sheet files) audio paging, 250t AutoCAD (Autodesk)

colors, 21, 21t electronic layout files, 283 origin, 19 requirements for, 13 screened colors, 22t terminology interchangeable with MicroStation, 15–16t

automated external defibrillator (AED), 257t aviation information systems, 279t

B baggage handling system, 233t, 259, 276t Baggage Information Displays (BIDS), 251t beams

structural buildings, 143t, 147t structural civil, 156t, 159t

bell system, 222t Bentley MicroStation. See MicroStation (Bentley) BIDS (Baggage Information Displays), 251t border sheets, 28, borings

geophysical, 130t borrow areas, 63t, 74t, 80t, 84t, 91t bracing

structural buildings, 143t structural civil, 156t

bridges. See also structural civil, 44t, 49t, 64t, 70t, 84t, 91t, 101t, 115t, 122t, 151t, 154t, 156t

brine system, 205t


CADD - Index

buildings and primary structures. See also structural buildings

eco-restoration plan, 77t flood control plan, 154t grading plan, 74t hazardous materials drawings, 56t navigation dredging plan, 84t profiles

civil drawings, 115t shore bankline, 80t site plan, 63t X-sections

civil drawings, 122t

C cable system, 220t, 222t, 234t cable television (CATV) systems, 250–251t, cabling. See primary electrical cables; secondary electrical

cables CADD files, limitations of, 15 CADD Standards, 13 CADD Symbols, 281 carpet/carpet tile, 178t Cartesian coordinates, 19 cathodic protection system, 226t CATV (cable television) system, 250–251t, CCTV (closed-circuit television) systems, 222–223t ceilings, reflected ceiling plan, 166t central dictation system, 223t channels

flood control plan, 92t navigation dredging plan, 85t profiles

civil drawings, 115t shore bankline, 80t site plan, 64t X-sections

civil drawings, 122t chemical treatment system, 199t chilled water system, 199t. See also high

temperature/chilled water system civil drawings

airfield plan, 105–108t demolition plan, 62t details, 129t drawing/working units for, 16 eco-restoration plan, 77–79t elevations, 121t flood control plan, 91–100t grading plan, 74–76t joint layout plan, 104t naming conventions, 49t navigation dredging plan, 84–90t profiles, 115–120t sheet level/layer assignments, 324t shore bankline, 80–83t site plan, 63–73t

transportation site plan, 101–103t utilities plan, 109–114t X-sections, 122–128t

clock system, 223t closed-circuit television (CCTV) systems, 222–223t CO2 sprinkler system, 185t colors

of lines in graphics, 21 screened, 22, 22t

column plan, 146t columns

floor plan, 164t structural civil, 152t

common use self service (CUSS) kiosks, 254–255t communication systems plan

exterior, 228t intercom/public address system, 223t

communications demolition plan, 233t details, 237t riser diagrams, 236t sheet level/layer assignments, 309t telephone/data plan 234–235t

compact disks, labeling of, 30 compressed air, 205t condenser water system, 199t control diagrams, 216t control panels

fire alarm, 190t fire protection, 183t

controls baggage handling plan, 240t HVAC plan, 199t

conveyance (elevators, escalators, and moving walks), 257–258t

conveyor (baggage handling), 239t Cover Sheet Format

assignment table, 55t DCA, 41e drawing files, 33 IAD, 38e

CUSS (common use self service) kiosks, 254–255t

D data exchange, 29–31 DCA. See Ronald Reagan Washington National Airport decking


decontamination, 58t defibrillators, automated external (AED), 257t deliverables, 29–31 demolition levels/layers, 28 demolition plan

architectural, 163t aviation information systems, 253t baggage handling system, 238t, 241t


CADD - Index

civil drawings, 62t communications, 233t electrical, 217t electronic monitoring system, 256t fire alarm, 189t fire protection, 182t hazardous materials, 57t interiors, 173t landscape drawings, 134t mechanical, 198t plumbing, 193t public information system, 249t security and access control system, 243t structural buildings, 147t, 150t structural civil, 159t

Design Manual applicability of, 3 organization of, 3–4 revisions to, 5–6

details architectural, 172t civil, 129t communications, 237t electrical, 231t fire alarm, 191t fire protection, 187t hazardous materials, 61t interiors, 181t landscape, 138t mechanical, 215t plumbing, 196t security and access control system drawings, 248t structural buildings, 150t structural civil, 162t

dimension terminators, 27 discipline designators, 27, 29, 49t disposal areas, 58t ditches or washes

flood control plan, 93t site plan, 65t

documentation on drawing files, 30–31 documents, compliance with, 4 domestic water

flood control plan, 92–93t navigation dredging plan, 85–86t piping plan, 194t profiles

civil drawings, 115t site plan, 64–65t utilities plan, 109–110t X-sections

civil drawings, 122–123t doors, in floor plan, 164t drawing files

naming conventions, 33, 291–292 organization of, 44–48t setup of, 19–20

standards for, 19–20 drawing output, 29 drawings, text height, 23–24t drawing/working units, 16 dredging plan

civil site plan, 65t flood control plan, 93t navigation, 84–90t shore bankline, 80t

dual temperature system, 200t ductbanks. See underground ductbanks dust and fume collection systems, 200t

E eco-restoration plan, 77–79t electrical cables. See primary electrical cables; secondary

electrical cables electrical drawings

airfield lighting plan, 229–230t demolition plan, 217t details, 231t electrical utilities plan, 226–227t exterior communications systems plan, 228t grounding system plan, 225t lighting plan, 218–219t mechanical drawings, 46t naming conventions, 51t power plan, 220–221t riser/one-line diagrams, 232t sheet level/layer assignments, 274t special systems plan, 222–224t

electrical utilities plan, 226–227t electronic layout files, 283 electronic monitoring systems

demolition plan, 256t drawings, numbering and organization of, 47t sheet level/layer assignments, 280t

elevations architectural, 170t civil drawings, 73t, 121t flood control plan, 100t interiors, 180t mechanical, 213t shore bankline, 83t structural buildings, 147–148t

elevators, 257–258t emergency fixtures, 58t energy monitoring control systems, 223t energy recovery system, 203t equipment

architectural, 168t fire alarm system, 190t furniture plan, 174t life safety plan, 183t material handling, 210t specialty mechanical, 205–207t telephone/data plan, 234t


CADD - Index

erosion and sediment control. See also riprap and other permanent erosion control items

civil site plan, 65–66t flood control plan, 94t grading plan, 75t structural buildings, 140t

escalators, 257–258t exhaust air system, 200t exterior communications systems plan, 228t

F fabrications

structural buildings, 141t, 144t structural civil, 152t, 154t, 157t

fasteners and connections structural buildings, 140t, 143t structural civil, 152t, 154t, 157t

FIDS (Flight Information Displays), 251t file accuracy, 19 files. See also drawing files

reference abbreviations, 283 electronic layout files, 283 list of, 284 use of, 28, 33

three-dimensional, 16 filled font, 23 fire alarm systems

demolition plan, 189t details, 191t numbering and organization of, 45–46t plan, 190t riser diagrams, 192t sheet level/layer assignments, 271t

fire protection. See also fire alarm systems baggage handling, 240t demolition plan, 182t details, 187t fire suppression plan, 185–186t life safety plan, 183–184t naming conventions, 51t numbering and organization of, 45t riser diagrams, 188t sheet level/layer assignments, 270t

fire ratings, 184t fire suppression plan, 185–186t Flight Information Displays (FIDS), 251t flood control plan, 91–100t flood hazard areas

flood control plan, 94t site plan, 66t

floodwalls flood control plan, 94–95t profiles

civil drawings, 116t site plan, 66t X-sections

civil drawings, 123t floor information

architectural, 164–165t electrical power plan, 220t fire alarm system, 190t fire suppression plan, 185t general drawings, 56t HVAC plan, 200t life safety plan, 183t piping plan, 194t special systems plan, 223t specialty piping and equipment, 205–206t telephone/data plan, 234t

floor patterns, 178–179t floor plans, 164–165t fonts, 23 foundation plan, 140–142t foundations, structural civil, 152t framing plan, 143–145t fuel system, 206t furniture plan, 174–175t

G gates


general drawings model file level/layer assignment tables, 54–56t numbering and organization of, 44t sheet file level/layer assignment tables, 260t

geotechnical drawings naming conventions, 50t sheet level/layer assignments, 263t

geothermal heat pump system, 200t, 208t global origin, 16, 17–18e glycol system, 200t, 206t grade linework

civil drawings, 67t eco-restoration plan, 77–78t flood control plan, 95t navigation dredging plan, 86–87t profiles

civil drawings, 116–117t shore bankline, 81t structural buildings, 141t structural civil, 152t X-sections

civil drawings, 123–124t grading plan, 74–76t graphic concepts

dimension terminators, 27 drawing orientation and north arrow, 24–25 line color, 21, 21t line widths, 20–21, 21t presentation graphics, 20 screening, 22, 22t text height, 23–24t


CADD - Index

text orientation, 26 text styles/fonts, 23

graphics system drawings, numbering and organization of, 47t

grid lines key plan, 56t profiles

civil drawings, 117t structural buildings, 146t structural civil, 154t, 157t X-sections

civil drawings, 124t grid system, 16, 17–18e grounding system plan, 284t

H habitats/landforms

eco-restoration plan, 77t halon system, 185t hazardous materials

demolition plan, 57t details, 61t naming conventions, 49t numbering and organization of, 44t pollution prevention plan, 58–59t sections, 60t sheet level/layer assignments, 261t

heat pump system, geothermal, 200t, 208t heliports, 106t, 117t, 124t high temperature/chilled water system

HTCW utilities plan, 208–209t HVAC plan, 200–201t

highways. See roads, streets, and highways hot water systems, heating, 202t HTCW utilities plan, 208–209t HVAC (heating, ventilating, and air conditioning) plan, 199–

204t hydraulic control systems, 206t

I IAD. See Washington Dulles International Airport iMUSE (intelligent Multiple User System Equipment)

system, 254t inch-pound text sizes and line type scales, 23–24t industrial waste piping, mechanical, 205t industrial waste water


civil drawings, 117t site plan, 67t utilities plan, 111t X-sections

civil drawings, 124t inert gas, 185t insulating (transformer) oil system, 206t

intelligent Multiple User System Equipment (iMUSE) system, 254t

intercom/public address system, 223t interiors

demolition plan, 173t details, 181t elevations, 180t floor patterns, 178–1798t furniture plan, 174–175t naming conventions, 50t sheet level/layer assignments, 269t signage placement plan, 177t system furniture workstation plan, 176t

irrigation civil drawings, 121t eco-restoration plan, 78t landscape plan, 137t profiles

civil drawings, 117t site plan, 67t utilities plan, 112t X-sections


J jacks, 234–234t joint layout plan, 104t joints

structural buildings, 141t, 144t, 147t structural civil, 154t, 157t, 159t

joists, 144t junction boxes, telephone/data plan, 235t

K key plan, 56t kiosks, common use self service, 254–255t

L labeling compact disks, 30 laboratory gas piping, 194–195t landscape

demolition plan, 134t details, 138t irrigation plan, 137t landscape plan, 135–136t naming conventions, 50t numbering and organization of, 44t sheet level/layer assignments, 265t

leader lines, 26 levees

flood control plan, 95–96t navigation dredging plan, 87t profiles, civil drawings, 117–118t site plan, 67–68t X-sections

civil drawings, 124–125t level/layer assignments (model files)


CADD - Index

annotation, 27–28 architectural, 163–172t aviation information systems, 253–2554t baggage handling system, 238–242t civil

airfield plan, 105–108t demolition plan, 62t details, 129t eco-restoration plan, 77–79t elevations, 121t flood control plan, 91–100t grading plan, 74–76t joint layout plan, 104t navigation dredging plan, 84–90t profiles, 115–120t shore bankline, 80–83t site plan, 63–73t transportation site plan, 101–103t utilities plan, 109–114t X-sections, 122–128t

communications, 233–237t demolition, 28 electrical

airfield lighting plan, 229–230t demolition plan, 217t details, 231t electrical utilities plan, 226–227t exterior communications systems plan, 228t grounding system plan, 225t lighting plan, 218–219t power plan, 220–221t riser/one-line diagrams, 232t special systems plan, 222–224t

electronic monitoring systems, 256–258t fire alarm, 189–192t fire protection, 182–188t general, 54–56t hazardous materials, 57–61t interiors, 173–181t landscape, 134t–138t mechanical

control diagrams, 216t demolition plan, 198t details, 215t elevations, 213t HTCW utilities plan, 208–209t HVAC plan, 199–204t machine design, 211–212t material handling, 210t sections, 214t specialty piping and equipment, 205–207t

model files, 27 naming conventions, 27 overview of, 27, 99–100 plumbing, 193–197t public information systems, 249–252t security and access control systems, 243–248t

sheet files, 28 structural buildings, 139–150t structural civil, 151–162t

level/layer assignments (sheet files) annotation, 29 architectural, 268t aviation information systems, 279t baggage handling system, 279t civil, 264t communications, 275t electrical, 274t electronic monitoring systems, 280t fire alarm system, 271t fire protection, 270t general, 260t geotechnical, 263t hazardous materials, 261t interiors, 269t landscape, 265t mechanical, 273t plumbing, 272t public information systems, 278t security and access control systems, 277t structural, 266t structural civil, 267t

life safety plan, 183–184t lighting

airfield, 229–230t electrical utilities plan, 218–219t, 226t life safety plan, 183t

lightning protection, 225t lines

color of, in graphics, 21, 21t leader, 26 screened color, 22, 22t spacing of, in graphics, 26 styles of, in graphics, 21, 21t width of, in graphics, 20–21, 20t

liquid fuel navigation dredging plan, 86t profiles

civil drawings, 116t site plan, 66t utilities plan, 110–111t X-sections

civil drawings, 123t lubrication oil, 206t

M machine design, 211–212t makeup air system, 203t Master Clock system, 251t master units, 19 material handling, 210t mechanical drawings

control diagrams, 216t demolition plan, 198t


CADD - Index

details, 215t elevations, 213t HTCW utilities plan, 208–209t HVAC plan, 199–204t machine design, 211–212t material handling, 210t naming conventions, 51t numbering and organization of, 46t sections, 214t sheet level/layer assignments, 273t specialty piping and equipment, 205–207t

media format, 29–30 medical/dental piping, 195t MicroStation (Bentley)

colors, 21, 21t electronic layout files, 283 file accuracy and, 19 global origin, 19 requirements for, 13 screened colors, 22t terminology interchangeable with AutoCAD, 15–16t

mixed air system, 202–203t model files. See also level/layer assignments (model files)

description of, 19–20, 27 level/layer assignment tables, 52–53 naming conventions, 33, 24e, 49–51t

monitoring stations, 58–59t monitoring systems, energy monitoring control systems,

223t. See also electronic monitoring systems monolithic flooring, 178t monotext font, 23 motor control panels, 240t moving walks, 257–258t Multi-User Flight Information Display System (MUFIDS),

250–251t

N naming conventions

addendum files, 36e drawing files, 33, 291–292 level/layer assignment, 27 model files, 33, 34e model files and level/layer tables, 49–51t sheet files, 33, 35e sketches, 33

natural gas mechanical, 206t navigation dredging plan, 88t profiles

civil drawings, 88t site plan, 68t utilities plan, 111–112t X-sections

civil drawings, 125t navigation dredging plan, 84–90t north arrow, orientation of, 24–25 nurse call/paging system, 223t

O obstructions

airfield plan, 106t occupancy plan, 169t oil, lubrication, 206t one-line diagrams. See riser diagrams orientation of drawing, 24–25 origin of drawing file, 17–18e, 19 outline font, 23 overrun areas

airfield plan, 106t profiles



P PA system, 224t pads


civil drawings, 118t structural buildings, 140t X-sections

civil drawings, 125t paging system, 223t, 250t parking lots

flood control plan, 96t profiles

civil drawings, 118t site plan, 68–69t transportation site plan, 101–102t X-sections

civil drawings, 125t pavement

airfield plan, 106–107t flood control plan, 96–97t joint layout plan, 104t navigation dredging plan, 88t profiles

civil drawings, 118t site plan, 69t transportation site plan, 102t X-sections

civil drawings, 126t penetrations

HVAC plan, 203t plumbing piping plan, 195t specialty piping and equipment plan, 207t

pipe/piping plumbing, 194–195t specialty mechanical, 205–207t

Plan Sheets for IAD, 39e plants, for landscape, 135t platforms

structural buildings, 144t structural civil, 152t, 154t, 157t


CADD - Index

plot size for drawings, 29 plumbing

demolition plan, 193t details, 196t naming conventions, 51t numbering and organization of, 46t piping plan, 194–195t riser diagrams, 196t sheet level/layer assignments, 272t

police ranges site plan, 68t

pollution areas, 59t pollution prevention plan, 58–59t power

electrical plan, 220–221t electrical special systems plan, 223t electrical utilities plan, 226–227t

presentation graphics, 20 primary electrical cables

electrical utilities plan, 227t process piping, 207t profiles

civil drawings, 115–120t project grid

DCA, 18e IAD, 17e

Project Identifier, 43t project organization, 13–14 property

flood control plan, 96t navigation dredging plan, 88t site plan, 69t X-sections

civil drawings, 125–126t proportional font, 23 public address system, 224t public information systems

demolition plan, 249t drawings, numbering and organization of, 48t plan, 250–252t sheet level/layer assignments, 278t

Q Quality Check (QC) CADD checklist, 33

R railroads

profiles civil drawings, 118t

transportation site plan, 102t X-sections

civil drawings, 126t raw water piping, 207t reference files

abbreviations, 283 electronic layout files, 283 list of, 284

use of, 28, 33 reference outlines

structural buildings, 141t, 144t, 146t structural civil, 153t, 154t, 158t

reflected ceiling plan, 166t refrigeration system, 203t reinforcement

structural buildings, 141t, 144t, 146t structural civil, 152–153t, 154t, 157–158t

relief air system, 203t relocation, 240–241t resilient flooring, 178–1798t revisions to Design Manual, 5–6 riprap and other permanent erosion control items. See also

erosion and sediment control flood control plan, 97t navigation dredging plan, 88–89t shore bankline, 81t site plan, 70t

riser diagrams communications, 236t electrical, 232t fire alarm, 192t fire protection, 188t plumbing, 197t security and access control systems, 246–247t

rivers civil drawings, 121t flood control plan, 97t navigation dredging plan, 88t profiles


civil drawings, 126t roads, streets, and highways

flood control plan, 97t site plan, 70t transportation site plan, 102–103t X-sections

civil drawings, 126t Ronald Reagan Washington National Airport

cover sheet for, 41e project grid, 18e Sheet Title Block, format for, 40e

roof plan, 167t runways. See also taxiways




S safety features, structural civil, 154t, 158t sample points

hazardous materials drawings, 59t


CADD - Index

sanitary drainage piping, 195t sanitary sewer


civil drawings, 119–120t site plan, 70–71t utilities plan, 112–113t X-sections

civil drawings, 126–190t SCADA (Supervisory Control & Date Acquisition), 257t screening of graphics, 22, 22t secondary electrical cables

electrical utilities plan, 227t sections

architectural, 171t hazardous materials, 60t mechanical, 214t structural buildings, 149t structural civil, 160–161t X-sections

civil drawings, 128t security and access control systems

demolition plan, 243t details, 248t drawings, numbering and organization of, 48t electrical special systems plan, 223–224t riser diagrams, 246–247t security plan, 244–245t sheet level/layer assignments, 277t

sewer. See sanitary sewer; storm sewer sheet files. See also level/layer assignments (sheet files)

description of, 19–20, 28 naming conventions, 33, 35e

Sheet Title Block, format for DCA, 40e IAD, 37e

shore bankline eco-restoration plan, 78t level/layer naming and descriptions, 80–83t

signage system drawings, numbering and organization of, 47t

signs/signage placement plan, interiors, 177t structural buildings, 144t structural civil, 158t

site features flood control plan, 97–98t profiles


civil drawings, 126t site improvement, landscape plan, 135–136t site information, general drawings, 56t site plan, civil, 63–73t sketches, addenda, 33

slabs structural buildings, 141–142t structural civil, 154–155t, 158t

slanted font, 23 smoke/pressurization control, 184t software, requirements for, 13 sound system, 224t special systems

electrical, 222–224t, 227t sprinkler system, 185–186t staging, 241t standards

acceptable, 4–5 CADD, 13 drawing file, 19–20 references, 284

steam system, 203–204t stiffeners

structural buildings, 144–145t structural civil, 158t

storage facilities, 59t storm drainage piping, 195t storm sewer


civil drawings, 120t shore bankline, 81–82t site plan, 71t utilities plan, 113–114t X-sections

civil drawings, 127–128t streets. See roads, streets, and highways structural buildings

column plan, 146t demolition plan, 139t details, 150t elevations, 147–148t foundation plan, 140–142t framing plan, 143–145t naming conventions, 50t numbering and organization of, 45t sections, 149t sheet level/layer assignments, 266t

structural civil decks, 154–155t details, 162t elevations, 159–160t sections, 160–161t sheet level/layer assignments, 267t substructure, 151–153t superstructure, 156–158t

styles of lines in graphics, 21, 21t submittal requirements for drawings, 30 subunits, 19 Supervisory Control & Date Acquisition (SCADA), 257t supports


CADD - Index


symbols, CADD, 281 system furniture workstation plan, 176t

T target systems, 16 taxiways. See also runways



civil drawings, 128t telecommunications drawings, naming conventions for, 51t telephone/data plan, 234–235t temporary work, 241t terminators, 26 terminology, interchangeable, between AutoCAD and

MicroStation, 15–16t text height, on drawings, 23–24t three-dimensional files, 16 tile flooring, 179t Title Block, format for

DCA, 40e IAD, 37e

topography airfield plan, 107–108t eco-restoration plan, 78–79t flood control plan, 98–99t grading plan, 75–76t joint layout plan, 104t navigation dredging plan, 89–90t shore bankline, 82–83t site plan, 71–73t transportation site plan, 103t utilities plan, 114t

transfer air system, 204t transportation site plan, 101–103t trusses


TSA entities, 240t TV antenna system, 224t

U underground ductbanks

communication system plan, 228t electrical utilities plan, 226t

utilities plan civil drawings, 109–114t domestic water, 109–110t electrical, 226–227t HTCW, 208–209t industrial waste water, 111t irrigation, 111t liquid fuel, 110–111t natural gas, 111–112t sanitary sewer, 112–113t storm sewer, 113–114t

V visual paging, 250t

W walls

floor plan, 165t structural buildings, 142t, 145t, 147t structural civil, 153t, 159t

Washington Dulles International Airport cover sheet for, 38e plan sheet for, 39e project grid, 17e Sheet Title Block, format for, 37e

water supply and distribution, fire suppression plan, 186t water systems. See domestic water; high

temperature/chilled water system; industrial waste water

waterway specialties, 153t wetlands

eco-restoration plan, 79t width of lines in graphics, 20–21, 20t windows, in floor plan, 165t wireless & radio system

drawings, numbering and organization of, 47t working units, 16 workstation plan, 176t

X X-sections for civil drawings, 54, 62-65t


CADD - Index

(This Page Blank)


CADD - Index

END OF DOCUMENT

CADD 2010 - MWAA

Documents

Transcript of CADD 2010 - MWAA