Patent Pending

Keep it watertight with

Welded steel anchor Wood/Steel anchorConcrete anchor

Sealable scaffold attachment system for exterior plaster

Enhance Safety and EliminateWater Intrusion at Scaffold Ties

Toll Free (877) 490-8884

THE PROBLEM Water intrusion at conventional push pull wire ties.

THE SOLUTIONTHE SOLUTION Sealable scaffold attachments.Sealable scaffold attachments.

Bumperite Waterguards enhance Safety and eliminate Liabilitydue to leaks caused by conventional scaffold wire ties assemblies.

Patent Pending

• SAFETY OSHA compliantEngineered and tested structural attachment for scaffolding (4500) lbs. Report # L-06-3265 Ideal for tarped or enclosed scaffolds in high wind conditions.

• REDUCED LABOR COSTEliminate costly end laps and their cuts to building papers verses conventional scaffold wire ties.Removable bumper allows easy access to difficult work areas.* Promotes the continuous installation of building materials.

• RELIABILITY Water tested to ASTM E331-00 at Smith-Emery laboratories, Inc. Los Angeles, CA. Report

# L-06-3059

*See installation instructions.

Patent Pending

WARRANTY: Bumperite Waterguards, LLC. liability expressed or implied is limited to the selling price of any defected goods. User shall determine the suitability of this product for the intended use by doing field test before using, and assumes all risk and liabilities in connection and seals therewith.

Welded Steel Anchor INSTALLATION PROCEDURE

• Determine spacing requirement to insure safe scaffold erection.*

• Measure distance between slab edge bent plate and outer face of stud framing.

• Cut the anchor strut to length as to flush out with face of stud framing.

• Align the anchor strut with the bent plate and stud framing (true, square, and plumb) per detail.

• Weld anchor strut to building bent plate per welding detail shown.

• The use of a certified welder and E7018 rod or equal is recommended.

*Spacing requirements for application should be determined by a competent scaffold erector or structural engineer per building and safety codes prior to installation. The temporary disconnection and reconnection of this product at erected scaffold should only be performed one connection at a time and only after it is determined safe to do so. The final determination of safety is the sole responsibility of the end user and should be determined by a competent and qualified person. Follow all OSHA, Federal, State, and Local requirements to ensure scaffold safety.

To ensure safety, use only components manufactured by Bumperite Waterguards, LLC. at scaffold attachment.

1/8”

Patent Pending

Bumperite Attachment To Steel Bent Plate

Illustrations and load Capacity provided by FICCADENTI & WAGGONER, Consulting Structural Engineers, Inc

WOOD INSTALLATION PROCEDURE

• Determine spacing requirement to insure safe scaffold erection.*

• Review screw matrix provided to determine screw size and quantity required for safe installation.

• Install Bumperite anchor plate where suitable framing and or backing occurs to ensure sufficient strength required to carry intended scaffold load.

• Apply compatible sealant between Bumperite anchor plate & building papers to ensure seal at screws.

• Ensure complete screw embedment at pre-drilled holes in anchor plate.

*Spacing requirements for application should be determined by a competent scaffold erector or structural engineer per building and safety codes prior to installation. The temporary disconnection and reconnection of this product at erected scaffold should only be performed one connection at a time and only after it is determined safe to do so. The final determination of safety is the sole responsibility of the end user and should be determined by a competent and qualified person. Follow all OSHA, Federal, State, and Local requirements to ensure scaffold safety.

To ensure safety, use only components manufactured by Bumperite Waterguards, LLC. at scaffold attachment.

Patent Pending

See engineered detail.

Bumperite Attachment to Wood FramingBumperite Attachment to Wood Framing

Fastener Type(Screw Size x

Length) w/ 2 Fasteners w/ 4 Fasteners w/ 6 Fasteners w/ 8 Fasteners

#12 x 2" Screw 410 lbs. 820 lbs. 1080 lbs. 1232 lbs.

#12 x 11⁄2 " Screw 308 lbs. 616 lbs. 924 lbs. 1232 lbs.

#10 x 2" Screw 360 lbs. 720 lbs. 1080 lbs. 1232 lbs.

#10 x 11⁄2 " Screw 270 lbs. 540 lbs. 810 lbs. 810 lbs.

Allowable Screw withdraw Value (P):

Allowable Nail Withdraw Value (P):

Fastener Type w/ 2 Fasteners w/ 4 Fasteners w/ 6 Fasteners w/ 8 Fasteners

16d Nail 40 lbs. 80 lbs. 120 lbs. 160 lbs.

10d Nail 36 lbs. 72 lbs. 108 lbs. 144 lbs.

Illustrations and load Capacity provided by FICCADENTI & WAGGONER, Consulting Structural Engineers, Inc

STEEL FRAMED INSTALLATION PROCEDURE

• Determine spacing requirement to insure safe scaffold erection.*

• Review backing plate requirements.

• Install Bumperite anchor plate over 12 gage backing plate per diagram to ensure sufficient strength required to carry intended scaffold load.

• Apply compatible sealant between Bumperite anchor plate & building papers to ensure seal at screws.

• Ensure complete screw embedment at pre-drilled holes in anchor plate.

Patent Pending

*Spacing requirements for application should be determined by a competent scaffold erector or structural engineer per building and safety codes prior to installation. The temporary disconnection and reconnection of this product at erected scaffold should only be performed one connection at a time and only after it is determined safe to do so. The final determination of safety is the sole responsibility of the end user and should be determined by a competent and qualified person. Follow all OSHA, Federal, State, and Local requirements to ensure scaffold safety.

To ensure safety, use only components manufactured by Bumperite Waterguards, LLC. at scaffold attachment.

See engineered detail.

Bumperite Attachment to Light Gauge FramingBumperite Attachment to Light Gauge Framing

Minimum Design Requirements ::

ALLOWABLE FORCE (P) = 1,000 LBS.

• For scaffold application this product complies w/ OSHA requirements • 12 ga. Deck Edge Clip• 18 ga. Wall Studs• 8”x12 ga.x11/2” Fl. Track• Track Blocking must be located within 6” of the Deck Edge Clip

Illustrations and load Capacity provided by FICCADENTI & WAGGONER, Consulting Structural Engineers, Inc

Bumperite Attachment to Light Gauge FramingBumperite Attachment to Light Gauge Framing

Minimum Design Requirements ::

ALLOWABLE FORCE (P) = 500 LBS.

• For scaffold application this product complies w/ OSHA requirements • 12 ga. Deck Edge Clip• 18 ga. Wall Studs• 6”x16 ga.x1-1/2” Fl. Track• Track Blocking must be located within 6” of the Deck Edge Clip

Illustrations and load Capacity provided by FICCADENTI & WAGGONER, Consulting Structural Engineers, Inc

6” x 16GA x 1-1/2” FLANGETRACK W / CUPPED

FLANGES @ ENDS EXTEND WEB TAB ATTACHMENT TO

(E) STUD AS SHOWN(4) # 8 S.M.S. EA. END

ALT. #1

CONCRETE INSTALLATION PROCEDURE

• Determine Bumperite spacing requirement and concrete psi values suitable for safe scaffold erection.*

• Install Bumperite anchor plate at concrete slab edge with a minimum of two concrete anchors bolts, see engineered detail.

• Install concrete anchors per manufactures installation guidelines.

• Ensure complete anchor boltembedment for maximum strength.

Patent Pending

*Spacing requirements for application should be determined by a competent scaffold erector or structural engineer per building and safety codes prior to installation. The temporary disconnection and reconnection of this product at erected scaffold should only be performed one connection at a time and only after it is determined safe to do so. The final determination of safety is the sole responsibility of the end user and should be determined by a competent and qualified person. Follow all OSHA, Federal, State, and Local requirements to ensure scaffold safety.

To ensure safety, use only components manufactured by Bumperite Waterguards, LLC. at scaffold attachment.

See engineered detail.

Bumperite Attachment to Concrete DeckBumperite Attachment to Concrete Deck

Illustrations and load Capacity provided by FICCADENTI & WAGGONER, Consulting Structural Engineers, Inc

BUMPERITE QUICK-TAB Optional feature

• The specially designed Quick-tab is a scaffold erectors dream.

• Fast and easy installation with no hassle.

• A temporary attachment to building slab edge during scaffold erection prior to exterior wall framing and final welded attachment of Bumperite Waterguard.

• Available upon request.

• See engineered detail

• WARNING: The Quick- tab attachment is not to be used at tarped or enclosed scaffolds.

Patent Pending

*Spacing requirements for application should be determined by a competent scaffold erector or structural engineer per building and safety codes prior to installation. The temporary disconnection and reconnection of this product at erected scaffold should only be performed one connection at a time and only after it is determined safe to do so. The final determination of safety is the sole responsibility of the end user and should be determined by a competent and qualified person. Follow all OSHA, Federal, State, and Local requirements to ensure scaffold safety.

To ensure safety, use only components manufactured by Bumperite Waterguards, LLC. at scaffold attachment.

Bumperite QuickBumperite Quick--Tab AttachmentTab Attachment

Illustrations and load Capacity provided by FICCADENTI & WAGGONER, Consulting Structural Engineers, Inc

Manufacturer recommends the use of Densglass Gold exterior sheathing, butyl sealant, Tyvek Straight Flash, minimum UU-B-790a grade D, building paper, and

three coat cement plaster per testing report L-06-3059 from Smith-Emery Laboratories, Inc. using test method ASTM E331-00

WARRANTY: Bumperite Waterguards, LLC. liability expressed or implied is limited to the selling price of any defected goods. User shall determine the suitability of this product for the intended use by doing field test before using, and assumes all risk and liabilities in connection therewith.

RECOMMENDED METHOD OF SEAL AT CONNECTION

Patent Pending

Patent PendingStep by Step

Water tested to ASTM E 1105-00 & ASTM E 331-00 by Architectural Testing, Inc.Report No: 90353.01-701-43

WARRANTY: Bumperite Waterguards, LLC. liability expressed or implied is limited to the selling price of any defected goods. User shall determine the suitability of this product for the intended use by doing field test before using, and assumes all risk and liabilities in connection therewith.

RECOMMENDED METHOD OF SEAL AT WOOD / STEEL FRAMEDANCHOR PLATE TO EXTERIOR WATER MANAGEMENT SYSTEM

Patent Pending

Patent PendingStep by Step at wood / steel framed plates

BUMPERITE - VS - WIRE TIES

Testing at Smith-Emery Laboratories suggest that the Bumperite Waterguard peak tension load is MANY TIMES STRONGER than conventional double strand #12

black annealed wire tie assemblies.

OSHA 1926.451(c)(1) states, Capacity- - Scaffolds and scaffold components must support

at least 4 times the maximum intended load.

Sealable & strength Difficult to seal & weaker

Patent Pending

For More Information Please Contact Us AtINFO@BUMPERITE.COM

Bumperite Waterguards, LLC.

Toll free (877) 490-8884

See Our Web Site AtBumperite.com