Building Structures: Column & Beam analysis
-
Upload
euxuan-ong -
Category
Education
-
view
44 -
download
6
Transcript of Building Structures: Column & Beam analysis
Building StructuresProject Two:
Structural Analysis of a Bungalow
Bachelor of Science (Hons) in ArchitectureSchool of Architecture, Building & Design
Taylor’s University
Tutor: Mr. Adib
Liew Jin 03Ong Euxuan 0319050Ricco Soh Zheng Wei 0319
Table of Content
1.0 Introduction
2.0 Architectural Plans 2.1 Ground Floor Plan
2.2 First Floor Plan2.3 Roof Plan
3.0 Structural Plan3.1 Ground Floor Plan3.2 First Floor Plan3.3 Roof Plan
4.0 Load Distribution Plan4.1 Ground Floor Plan4.2 First Floor Plan4.3 Roof Plan
5.0 3D Structural Model
6.0 Individual Beam Analysis6.1 Liew Jin6.2 Ong Euxuan6.3 Ricco Soh
7.0 Individual Column Analysis7.1 Liew Jin7.2 Ong Euxuan7.3 Ricco Soh
8.0 Conclusion
9.0 References
1.0 Introduction
For this project, we are to design a two-storey bungalow unit based on the given outlines. The layout of the bungalow should be a combination of two chosen outlines.
We are to frame and design the structural skeleton of the bungalow, then identify the beams and columns in the bungalow design. Then we are to examine and analyze the structure, as well as its load distribution, then calculate the amount of load each beam/column is subjected to. Each member is given six beams and three columns.
Bungalow Introduction
The designed bungalow is two-storey high, and it consists of the following components: one master bedroom with attached bathroom, a minimum of three bedrooms, two bathrooms, kitchen, living hall, dining area and a storeroom.
The chosen outlines:
Formulas
Slab System
Ly/Lx > 2 = One way slab systemLy/Lx < 2 = Two way slab system
Columns
Beam self-weight = Beam size x Density of reinforced concrete x Length
Slab dead load = Thickness x density of RC (UBBL) x Tributary area
Slab live load = Live load (Room live load factor - UBBL) x Tributary area
Brick wall dead load = Wall height x Wall thickness x Density of bricks (UBBL) x Length
Column self-weight = Width x Length x Height x Density of RC (UBBL)
Beams
Beam self-weight = Beam size x Density of reinforced concrete
Slab dead load = Thickness x density of RC (UBBL) x Lx/2 (for trapezoids) = Thickness x density of RC (UBBL) x Lx/2 x 2/3 (for triangles)
Slab live load = Live load (Room live load factor - UBBL) x Lx/2 (for Trapezoids) = Live load (Room live load factor - UBBL) x Lx/2 x 2/3 (for Triangles)
Brick wall dead load = Wall height x Wall thickness x Density of bricks (UBBL)
UBBL Specifications
Live Load
Bedroom = 1.5 kN/m2 Living Room = 4.0 kN/m2
Dining Room = 2.0 kN/m2
Kitchen = 3.0 kN/m2
Corridor = 4.0 kN/m2
Bathroom = 2.0 kN/m2
Study Room = 1.5 kN/m2
Family Area = 2.0 kN/m2
Store Room = 2.5 kN/m2
Dead Load (Structural Materials)
Reinforced Concrete Density = 24kN/m3
Brick Density = 19kN/m3
.
2.0Architectural Plans
2.1 Architectural Plan: Ground Floor(not to scale)
2.2 Architectural Plan: First Floor(not to scale)
2.1 Architectural Plan: Roof(not to scale)
3.0Structural Plans
3.1 Structural Plan: Ground Floor(not to scale)
3.1 Structural Plan: First Floor(not to scale)
3.1 Structural Plan: Roof (not to scale)
4.0Load Distribution
Plans
4.1 Load Distribution Plan: Ground Floor(not to scale)
4.1 Load Distribution Plan: First Floor(not to scale)
5.0 Structural Model
6.0Beam Analysis
Liew Jin
Ong Euxuan
Ricco Soh Zheng Wei
7.0Column Analysis
Liew Jin
Ong Euxuan
Ricco Soh Zheng Wei
8.0 Conclusion
By the end of this project, we have came to understand the concept of these structural systems. We are able to identify these structural components based on evidence. We have gained understanding and knowledge on the load distribution paths and structural framings of a building structure.
We learned to identify critical structural members, as well as analyze them. We also learned to quantify the amount of load acting on beams and columns.
9.0 References
A