INDEX FOR CODES AND STANDARDSStandard No. Dual No. ref. Year/Edition Title Remarks

BS 4-1 2005 Structural steel sections - Part 1: Specification for hot-rolled sectionsBS 60270 IEC 60270 2001 High-voltage test techniques - Partial discharge measurements Replaces BS 4828BS 60289 IEC 60289 1995 Reactors Replaces BS 4944BS 449-2 1969 The use of structural steel in building - Part 2: Metric unitsBS 466 1984 Specification for Power driven overhead travelling cranes, semi-goliath and goliath cranes for general useBS 648 1964 Weights of building materials

BS 848-1 ISO 5801 1997 Fans for general purposes - Part 1: Performance testing using standardized airways

BS 848-2.1 BS ISO 13347-1 2004 Industrial fans - determination of fan sound power levels under standardized laboratory conditions - Part 1: general overview Replaces BS 848-2

BS 848-2.2 BS ISO 13347-2 2004 Replaces BS 848-2

BS 848-2.4 BS ISO 13347-4 2004 Replaces BS 848-2

BS 848-2.5 BS EN ISO 5136 2003 Acoustics - Determination of sound power radiated into a duct by fans and other air-moving devices - In-duct methodBS 848-3 ISO 5802 2001 Fans for general purposes - Part 3: Performance testing in situBS 848-4 ISO 13351 1997 Fans for general purposes - Part 4: DimensionsBS 848-5 ISO 12499 1999 Fans for general purposes - Part 5: Specification for mechanical safety (guarding)BS 848-6 BS ISO 14695 2003 Fans for general purposes - Method of measurement of fan vibrationBS 848-7 BS ISO 14694 2003 Fans for general purposes - Part 7: Specifications for balancing and vibrationBS 848-8 ISO 13349 1999 Fans for general purposes - Part 8: Vocabulary and definition of categoriesBS 848-9 ISO 13348 2006 Fans for general purposes - Part 9: Tolerances, methods of conversion and technical data presentationBS 848-10 ISO 13350 1999 Fans for general purposes - Part 10: Performance testing of jet fansBS 1377-1 1990 Soils for civil engineering purposes - Part 1: General Reqmnts and sample preparation

BS 1924-1 1990

BS 1924-2 1990 Stabilized materials for civil engineering purposes - Part 2: Methods of test for cement-stabilized and lime-stabilized materialsBS 4449 2005 Steel for the reinforcement of concrete-weldable reinforcing steel -bar, coil and decoiled product - Spec.BS 4482 2005 Steel wire for the reinforcement of concrete products - Spec.BS 4483 2005 Steel fabric for the reinforcement of concrete - Spec.BS 5351 1986 Spec for Steel ball valves for the petroleum, petrochemical and allied industries Confirmed 1991

BS 5628-1 2005 CoP for the use of masonry - Part 1: Structural use of unreinforced masonryBS 5628-2 2005 CoP for the use of masonry - Part 2: Structural use of reinforced and prestressed masonryBS 5628-3 2005 CoP for the use of masonry - Part 3: Materials and components, design and workmanshipBS 5950-1 2000 Structural use of steelwork in building - Part 1: CoP for design - Rolled and welded sections

BS 5950-2 2001 Structural use of steelwork in building - Part 2: Spec for materials, fabrication and erectio - Rolled and welded sectionsBS 5950-3.1 1990 Structural use of steelwork in building - Part 3.1 CoP for design of simple and continuous composite beams Replaces CP 117-1BS 5950-4 1994 Structural use of steelwork in building - Part 4: CoP for design of composite slabs with profiled steel sheetingBS 5950-5 1998 Structural use of steelwork in building - Part 5: CoP for design of cold formed thin gauge sectionsBS 5950-6 1995 Structural use of steelwork in building - Part 6: CoP for design of light gauge profiled steel sheetingBS 5950-7 1992 Structural use of steelwork in building - Part 7: Spec for materials and workmanship: cold formed sectionsBS 5950-8 2003 Structural use of steelwork in building - Part 8: CoP for fire resistant designBS 5950-9 1994 Structural use of steelwork in building - Part 9: CoP for stressed skin design

Industrial fans - determination of fan sound power levels under standardized laboratory conditions - Part 2: Reverberant room method

Industrial fans - determination of fan sound power levels under standardized laboratory conditions - Part 4: Sound intensity method

Replaces BS EN 25136 & partially supersedes BS

848-2

Stabilized materials for civil engineering purposes - Part 1: Gen. reqmnts, sample prep. and tests on materials prior to stabilization

A B C D E12345678910

11

12

13

14

151617181920212223

24

25

2627282930313233

34

35363738394041

BS 6031 1981 CoP for EarthworksBS 6399-1 1996 Loading for buildings - Part 1: CoP for dead and imposed loadsBS 6399-2 1997 Loading for buildings - Part 2: CoP for wind loadsBS 8000-1 1989 Workmanship on building sites - Part 1: CoP for excavation and fillingBS 8004 1986 CoP for FoundationsBS 8007 1987 CoP for Design of concrete structures for retaining aqueous liquids

BS 8110-1 1997 Structural use of concrete - Part 1: CoP for design and constructionBS 8110-2 1985 Structural use of concrete - Part 2: CoP for special circumstances

BS 8110-3 1985

BS 8500-1 2002 Concrete - Complementary British Standard to BS EN 206-1 - Part 1: Method of specifying and guidance for the specifier

BS 8500-2 2002 Concrete - Complementary British Standard to BS EN 206-1 - Part 2 Specification for constituent materials and concreteBS 8666 2005 Scheduling, dimensioning, bending and cutting of steel reinforcement for concrete - Specification

BS 60060-2 1995 High-voltage test techniques - Part 2: Measuring systems

BS 60076-4 2002 Power transformers - Part 4: Guide to the lightning impulse and switching impulse testing - Power transformers and reactorsBS EN 197-1 2000 Cement - Part 1: Composition, specifications and conformity criteria for common cementsBS EN 206-1 2000 Concrete - Part 1: Specification, performance, production and conformityBS EN 298 2003 Automatice gas burner control systems for gas burners and gas burning appliances with or without fans

BS EN 10021 1993 General technical delivery requirements for steel and iron productsBS EN 10025-1 2004 Hot rolled products of structural steels - Part 1: General technical delivery conditionsBS EN 10025-2 2004 Hot rolled products of structural steels - Part 2: Technical delivery conditions for non-alloy structural steels

BS EN 10025-3 2004

BS EN 10025-4 2004

BS EN 10025-5 2004

BS EN 10025-6 2004BS EN 10168 2004 Steel products - Inspection documents - List of information and descriptionBS EN 10204 2004 Metallic products - Types of inspection documents

BS EN ISO 14688-2 2004 Geotechnical investigation and testing - Identification and classification of soil - Part 2: Priinciples for a classification Partially replaces BS 5930

BS EN ISO 17000 2004 Conformity assessment - Vocabulary and general priinciplesBS EN ISO 17050-1 2004 Conformity assessment - Supplier's declaration of conformity - Part 1: General requirements. Replaces BS EN 45014BS EN ISO 17050-2 2004 Conformity assessment - Supplier's declaration of conformity - Part 2: Supporting documentation Replaces BS EN 45014

BS IEC 61511-1 2003

BS IEC 61511-2 2003

BS IEC 61511-3 2003

BS ISO TR 12767 1998

Structural use of concrete - Part 3: Design charts for singly reinforced beams, doubly reinforced beams and rectangular columns

Hot rolled products of structural steels - Part 3: Technical Delivery conditions for normalized/normalized rolled weldable fine grain structural steels

Hot rolled products of structural steels - Part 4: Technical delivery conditions for thermomechanical rolled weldable fine grain structural steels

Hot rolled products of structural steels - Part 5: Technical delivery conditions for structural steels with improved atmospheric corrosion resisitance

Hot rolled products of structural steels - Part 6: Technical delivery conditions for flat products of high yield strength structural steels in the quenched and tempered condition

Partially supercedes BS EN 45020 and ISO/IEC Guide

2

Functional safety - safety instrumented systems for the process industry sector - Part 1: Framework, definitions, system, hardware and software requirements

Functional safety - safety instrumented systems for the process industry sector - Part 2: Guidelines for the application of BS IEC 61511-1

Functional safety - safety instrumented systems for the process industry sector - Part 3: Guidance for the determination of the required safety integrity levels

Measurement of fluid flow by means of pressure-differential devices - Guidelines to the effect of departure from the specifications and operating conditions given by ISO 5167-1

A B C D E4243444546474849

50

51

52

5354

55

565758596061

62

63

64

65

6667

68

69

7071

72

73

74

75

IEC 60909-0 2001 Short-circuit currents in three-phase a.c. systems - Part 0: Calculation of currents

IEC 60909-1 2002IEC 60909-2 1992 Electrical equipment - data for short-circuit current calculations in accordance with IEC 909 (1988)IEC 60909-4 2000 Short-circuit currents in three-phase a.c. systems - Part 4: Examples for the calculation of short-circuit currentsIEC 60575 1977 Thermal-mechanical performance test and mechanical performance test on string insulator unitsIEC 60949 1988 Calculation of thermally permissible short-circuit currents, taking into account non-adiabatic heating effects

IEC 60068-2-27 BS EN 60068-2-27 1993 Environmental testing - Part 2: Tests - Test Ea and guidance: Shock Supercedes BS 2011-2IEC 61000-6-2 BS EN 61000-6-2 2001 Electromagnetic compatibility (EMC) - Part 6-2: Generic standards - Immunity for industrial environments

ISO 9000 BS EN ISO 9000 2005 Quality management systems - Fundamentals and vocabulary

BS 476-3 2004 Fire tests on building materials and structures - Part 3: Classification and method of test for external fire exposure to roofsBS 476-4 1984 Fire tests on building materials and structures - Part4: Non-combustibility test for materialsBS 476-6 1989 Fire tests on building materials and structures - Part 6: Method of test for fire propogation for products

BS 476-7 1997BS 476-10 1983 Fire tests on building materials and structures - Part 10: Guide to the principles and application of fire testing

BS 476-11 1998 Fire tests on building materials and structures - Part 11: Method of assessing the heat emission from building materials

BS 476-12 1991 Fire tests on building materials and structures - Part 12: Methods of test for ignitability of products by direct flame impingement

BS 476-13 ISO 5657 1987BS 476-15 ISO 5660 1993 Fire tests on building materials and structures - Part 15: Method for measuring the rate of heat release of products

BS 476-20 1987

BS 476-21 1987

BS 476-22 1987

BS 476-23 1987

BS 476-24 ISO 6944 1987

BS 476-31.1 1983BS 476-32 1989 Fire tests on building materials and structures - Part 32: Guide to full scale fire tests within buildingsBS 476-33 ISO 9705 1993 Fire tests on building materials and structures - Part 33: Full scale room test for surface productBS 499-1 1991 Welding terms and symbols - Part 1: Glossary for welding, brazing and thermal cutting

BS 499-1 Suppl. IEV 50 (851) 1992

BS 743 1970 Spec for Materials for Damp-proof coursesBS 1369-1 1987 Steel lathing for internal plastering and external rendering - Part 1: Spec for expanded metal and ribbed lathingBS 2452 1954 Specification for High pedestal or portal jib cranesBS 2853 1957 The design and testing of steel overhead runway beams

BS 3643-1 1981 Spec for ISO metric screw threads - Part 1: Principles and basic data

Short-circuit currents in three-phase a.c. systems - Part 1: Factors for the calculation of short-circuit currents according to IEC 60909-0

Fire tests on building materials and structures - Part 7: Method of test to determine the classification of the surface spread of flame of products

Fire tests on building materials and structures - Part 13: Method of measuring the ignitability of products subjected to thermal irradiance - [ISO title: Fire tests - Reaction to fire - Ignitability of building products]

Fire tests on building materials and structures - Part 20: Method for determination of the fire resistance of elements of construction (general principles)

Fire tests on building materials and structures - Part 21: Methods for determination of the fire resistance of loadbearing elements of construction

Fire tests on building materials and structures - Part 22: Methods for determination of the fire resistance of non-loadbearing elements of construction

Fire tests on building materials and structures - Part 23: Methods for determination of the contribution of components to the fire resistance of a structure

Fire tests on building materials and structures - Part 24: Method for determination of the fire resistance of ventilation ducts [ISO title: Fire resistance tests - Ventilation ducts]

Fire tests on building materials and structures - Part 31.1: Methods for measuring smoke penetration through doorsets and shutter assemblies - Section 31.1 Method of measurement under ambient temperature conditions

Welding terms and symbols - Part 1: Glossary for welding, brazing and thermal cutting - Supplement: Definitions for electric welding equipment

Partially replaced by BS 8215

A B C D E76

77

787980818283848586

87

8889

90

91

92

93

94

95

96

97

98

99

100

101

102103104

105

106

107108109110

BS 3643-2 1981 Spec for ISO metric screw threads - Part 2: Spec for selected limits of size BS 3692 2001 ISO metric precision hexagon bolts, screws and nuts - Specification

BS 4027 1996 Spec for Sulfate-resisting Portland cementBS 4190 2001 ISO metric black hexagon bolts, screws and nuts - SpecificationBS 4320 Confirmed 1998 1968 Spec for Metal washers for general engineering purposes metric series

BS 4395-1 1969

BS 4395-2 Confirmed 1998 1969BS 4550-0 1978 Methods of testing concrete - Part 0: General introduction

BS 4550-3.1 1978 Methods of testing concrete - Part 3: Physical tests - Section 3.1 IntroductionBS 4550-3.8 1978 Methods of testing concrete - Part 3: Physical tests - Section 3.8 Test for heat of hydrationBS 4550-6 1978 Methods of testing concrete - Part 6: Standard sand for mortar cubesBS 4551 2005 Mortar - Methods of test for mortar analysis - Chemical analysis and physical testing

BS 4592-1 1995 Industrial type metal walkways and stair treads - Part 1: Spec for open bar gratingsBS 4604-1 1970 Spec for The use of high strength friction grip bolts in structural steelwork metric series - Part 1: General grade

BS 4604-2 1970 Spec for The use of high strength friction grip bolts in structural steelwork metric series - Part 2: Higher grade (parallel shank)BS 4872-1 1982 Spec for Approval testing of welders when welding procedure approval is not required - Part 1: Fusion welding of steel

BS 4872-2 1976BS 4933 1973 Spec for ISO metric black cup and countersunk head bolts and screws with hexagon nutsBS 4994 1987 Specification for Design and construction of vessels and tanks in reinforced plasticsBS 5154 1991 Specification for Copper alloy globe, globe stop and check, check and gate valves

BS 5308-1 1986 Instrumentation cables - Part 1:Specification for polyethylene insulated cablesBS 5480 1990 Specification for Glass reinforced plastics (GRP) pipes, joints and fittings for use for water supply or sewerageBS 5531 1988 CoP for Safety in erecting stuctural steel framesBS 5606 Confirmed 1998 1990 Guide to Accuracy in building

BS 6073-2 1981 Precast concrete masonry units - Part 2: Method for specifying precast concrete masonry unitsBS 6231 1998 Specification for PVC-insulated cables for switchgear and controlgear wiring

BS 6290-2 1999BS 6290-3 1999 Lead-acid stationary cells and batteries - Part 3: Spec for the flat positive plate typeBS 6290-4 1997 Lead-acid stationary cells and batteries - Part 4: Spec for classifying valve regulated typesBS 6398 1983 Spec for Bitumen damp-proof courses for masonry

BS 6477 1992 Spec for Water repellents for masonry surfacesBS 6515 1984 Spec for Polyethylene damp-proof courses for masonryBS 6651 1999 CoP for protection of structures against lightning

BS 7121-1 2006 CoP for safe use of cranes - Part 1: GeneralBS 7121-2 2003 CoP for safe use of cranes - Part 2: Inspection, testing and examinationBS 7159 1989 CoP for Design and construction of glass reinforced plastics (GRP) piping systems for individual plants or sitesBS 7354 1990 CoP for Design of high-voltage open-terminal stations Supersedes BS 162

BS 7361-1 1991 Cathodic Protection - Part 1: CoP for land and marine applications formerly CP 1021BS 7430 1998 CoP for EarthingBS 7608 1993 CoP for Fatigue design and assessment of steel structuresBS 7668 2004 Weldable structural steels - Hot finished structural hollow sections in weather resistant steels - SpecificationBS 8007 1987 CoP for Design of concrete structures for retaining aqueous liquids

Specifies reqmnts in terms of test proc's in BS EN 196

Spec for High strength friction grip bolts and associated nuts and washers for structural engineering metric series - Part 1: General Grade

Spec for High strength friction grip bolts and associated nuts and washers for structural engineering metric series - Part 2: Higher grade bolts and nuts and general grade washers

Spec for Approval testing of welders when welding procedure approval is not required - Part 2: TIG or MIG welding of aluminium and its alloys

Lead-acid stationary cells and batteries - Part 2: Spec for the high-performance Plante positive type

Withdrawn from use but still available

A B C D E111112

113

114115

116

117

118119120121122123124

125

126

127

128129130131132133134135136137138139140

141

142143144145146147148149150151152

BS 8102 1990 CoP for Protection of structures against water from the groundBS 8215 1991 CoP for Design and installation of damp-proof courses in masonry constructionBS 8666 2005 Scheduling, dimensioning, bending and cutting of steel reinforcement for concrete - Specification

BS EN 196-1 2005 Methods of testing cement - Part 1: Determination of strengthBS EN 196-2 2005 Methods of testing cement - Part 2: Chemical analysis of cementBS EN 196-3 2005 Methods of testing cement - Part 3: determination of setting times and soundnessBS EN 196-5 2005 Methods of testing cement - Part 5: Pozzolanicity test for pozzolanic cementBS EN 196-6 1992 Methods of testing cement - Part 6: Determination of finenessBS EN 196-7 1992 Methods of testing cement - Part 7: Methods of taking and preparation samples of cementBS EN 196-8 2003 Methods of testing cement - Part 8: Heat of hydration - Solution methodBS EN 196-9 2003 Methods of testing cement - Part 9: Heat of hydration - Semi-adiabatic methodBS EN 197-4 2004 Cement - Part 4: Composition, specifications and conformity criteria for low early strength blastfurnace cementsBS EN 287-1 2004 Qualification test of welders - Fusion welding - Part 1: Steels

BS EN 288-9 1999BS EN 459-1 2001 Building lime - Part 1; Definitions, specifications and conformity criteria

BS EN 480-1 1998 Admixtures for concrete, mortar and grout - Test methods - Part 1: Reference concrete and reference mortar for testingBS EN 480-2 1997 Admixtures for concrete, mortar and grout - Test methods - Part 2: Determination of setting timeBS EN 480-4 2005 Admixtures for concrete, mortar and grout - Test methods - Part 4: Determination of bleeding of concreteBS EN 480-5 2005 Admixtures for concrete, mortar and grout - Test methods - Part 5: Determination of capillary absorptionBS EN 480-6 2005 Admixtures for concrete, mortar and grout - Test methods - Part 6: Infrared analysis

BS EN 480-8 1997 Admixtures for concrete, mortar and grout - Test methods - Part 8: Determination of the conventional dry material contentBS EN 480-10 1997 Admixtures for concrete, mortar and grout - Test methods - Part 10 Determination of water soluble chloride content

BS EN 480-11 2005BS EN 480-12 2005 Admixtures for concrete, mortar and grout - Test methods - Part 12: Determination of the alkali content of admixtures

BS EN 593 2004 Industrial valves - Metallic buttefly valvesBS EN 771-3 2003 Specification for masonry units - Part 3: Aggregate concrete masonry units (dense and light-weight aggregates)BS EN 845-1 2003 Specification for ancillary components for masonry - Part 1: Ties, tension straps, hangers and brackets

BS EN 934-2 2001

BS EN 934-3 2003BS EN 934-6 2001 Admixtures for concrete, mortar and grout - Part 6: Sampling, conformity control and evaluation of conformityBS EN 998-1 2003 Specification for mortar masonry - Part 1: Rendering and plastering mortarBS EN 998-2 2003 Specification for mortar masonry - Part 2: Masonry mortar

BS EN 1008 2002BS EN 3766 2003 Construction drawings - Simplified representation of concrete reinforcementBS EN 10029 1991 Spec for Tolerances on dimensions, shape and mass for hot rolled steel plates 3mm thick or above

BS EN 10056-1 1999 Structural steel equal and unequal leg angles - Part 1: DimensionsBS EN 10056-2 1993 Spec for Structural steel equal and unequal leg angles - Part 2: Tolerances on shape and dimensionsBS EN 10143 1993 Continuously hot-dip metal coated steel sheet and strip - Tolerances on dimensions and shape

BS EN 10296-1 2003

BS EN 10296-2 2005

Specification and approval of welding procedures for metallic materials - Part 9: Welding procedure test for pipeline welding on land and offshore site butt welding of transmission pipelines

Admixtures for concrete, mortar and grout - Test methods - Part 11: Determination of air void characteristics in hardened concrete

Admixtures for concrete, mortar and grout - Part 2: Concrete admixtures - Definitions, requirements, conformity, marking and labelling

Admixtures for concrete, mortar and grout - Part 3: Admixtures for masonry mortar - Definitions, requirements, conformity, marking and labelling

Mixing water for concrete - Specification for sampling, testing and assessing the suitability of water, including water recovered from processes in the concrete industry, as mixing water for concrete

Welded circular steel tubes for mechanical and general engineering purposes - Technical delivery conditions - Part 1: Non-alloy and alloy steel tubes

Welded circular steel tubes for mechanical and general engineering purposes - Technical delivery conditions - Part 2: Stainless steel

A B C D E153154155156157158159160161162163164165

166

167

168

169170171172

173

174

175

176177178179

180

181

182183184

185

186187188189190

191

192

BS EN 10297-1 2003

BS EN 10297-2 2005BS EN 10305-1 2002 Steel tubes for precision applications - Technical delivery conditions - Part 1: Seamless cold drawn tubesBS EN 10305-2 2002 Steel tubes for precision applications - Technical delivery conditions - Part 2: Welded cold drawn tubesBS EN 10305-3 2002 Steel tubes for precision applications - Technical delivery conditions - Part 3: Welded cold sized tubes

BS EN 10305-4 2003

BS EN 10305-5 2003

BS EN 10305-6 2005

BS EN 12266-1 2003

BS EN 12266-2 2002 Industrial valves - Testing of valves - Part 2: Tests, test procedures and acceptance criteria - Supplementary requirements

BS EN 12288 2003 Industrial valves - Copper alloy gate valvesBS EN 12329 2000 Corrosion protection of metals - Electrodeposited coatings of zinc with supplementary treatment on iron or steelBS EN 12330 2000 Corrosion protection of metals - Electrodeposited coatings of cadmium on iron or steel

BS EN 12350-1 2000 Testing fresh concrete - Part 1: SamplingBS EN 12350-2 2000 Testing fresh concrete - Part 2: Slump testBS EN 12350-3 2000 Testing fresh concrete - Part 3: Vebe testBS EN 12350-4 2000 Testing fresh concrete - Part 4: Degree of compactibilityBS EN 12350-5 2000 Testing fresh concrete - Part 5: Flow table testBS EN 12350-6 2000 Testing fresh concrete - Part 6: DensityBS EN 12350-7 2000 Testing fresh concrete - Part 7: Air content - Pressure methodsBS EN 12390-1 2000 Testing hardened concrete - Part 1: Shape, dimensions and other requirements for specimens and mouldsBS EN 12620 2002 Aggregates for concrete

BS EN 13001-1 2004 Crane safety - General design - Part 1: general principles and requirementsBS EN 13001-2 2004 Crane safety - General design - Part 2: Load effectsBS EN 13135-1 2003 Cranes - Safety - Design - Requirements for equipment - Part 1: Electrotechnical equipmentBS EN 13135-2 2004 Cranes - Equipment - Part 2: Non-electrotechnical equipment

BS EN 13139 2002 Aggregates for mortarBS EN 13414-1 2003 Steel wire rope slings - Safety - Part 1: Slings for general lifting service

BS EN 13414-2 2003 Steel wire rope slings - Safety - Part 2: Spec for information for use and maintenance to be provided by the manufacturerBS EN 13414-3 2003 Steel wire rope slings - Safety - Part 3: Grommets and cable-laid slings

BS EN 13622 2002 Gas welding equipment - Terminology - Terms used for gas welding equipment

BS EN 13636 2004 Cathodic protection of buried metallic tanks and related piping

BS EN 13923 2005 Filament-wound FRP pressure vessels - Materials, design, manufacturing and testingBS EN 14399-1 2005 High-strength structural bolting assemblies for preloading - Part 1: General requirementsBS EN 22553 ISO 2553 1995 Welded, brazed and soldered joints - Symbolic representation on drawings Supersedes BS 499-2BS EN 22858 ISO 2858 1993 End-suction centrifugal pumps (rating 16 bar) - Designation, nominal duty point and dimensions

Seamless circular steel tubes for mechanical and general engineering purposes - Technical delivery conditions - Part 1: Non-alloy and alloy steel tubes

Seamless circular steel tubes for mechanical and general engineering purposes - Technical delivery conditions - Part 2: Stainless steel

Steel tubes for precision applications - Technical delivery conditions - Part 4: Seamless cold drawn tubes for hydraulic and pneumatic power systems

Steel tubes for precision applications - Technical delivery conditions - Part 5: Welded and cold sized square and rectangular tubes

Steel tubes for precision applications - Technical delivery conditions - Part 6: Welded cold drawn tubes for hydraulic and pneumatic power systems

Industrial valves - Testing of valves - Part 1: Pressure tests, test procedures and acceptance criteria - Mandatory requirements

Supersedes BS 6755-1 & BS 5146 -1 & -2

Supersedes BS 6755-1 & BS 5146 -1 & -2

Supersedes gate valve elements of BS 5154

Superesedes BS 1199 & BS 1200

Partially supersedes BS 499-1

Partially supersedes BS 7361-1

Partially supersedes BS 4994

A B C D E

193

194

195196197

198

199

200

201

202

203

204205206207208209210211212213214215216217218

219

220

221

222

223

224

225

226227228

BS EN 60034-5 IEC 60034-5 2001 Supersedes BS 4999-105

BS EN 60034-6 IEC 60034-6 1994 Rotating electrical machines - Part 6: Methods of cooling (IC code) Superesedes BS 4999-106

BS EN 60034-7 IEC 60034-7 1993 Supersedes BS 4999-107BS EN 60034-9 IEC 60034-9 1998 Rotating electrical machines - Part 9: Noise limits

BS EN 60034-15 IEC 60034-15 1996 Rotating electrical machines - Part 15: Impulse voltage withstand levels of rotating a.c. machines with form-wound stator coils Supersedes BS 4999-115BS EN 60034-16-1 IEC 60034-16-1 1996 Rotating electrical machines - Part 16: Excitation systems for synchronous machines - Chapter 1: DefinitionsBS EN 60034-18-1 IEC 60034-18-1 1994 Rotating electrical machines - Part 18: Functional evaluation of insulation systems - Section 1: General guidelines

BS EN 60034-18-21 IEC 60034-18-21 1994

BS EN 60034-18-22 IEC 60034-18-22 2001

BS EN 60034-18-31 IEC 60034-18-31 1994BS EN 60044-1 IEC 60044-1 1999 Instrument transformers - Part 1: Current transformers Supersedes BS 7626BS EN 60044-2 IEC 60044-2 1999 Instrument transformers - Part 2: Inductive voltage transformers Supersedes BS 7625BS EN 60044-3 IEC 60044-3 2003 Instrument transformers - Part 3: Combined transformers Supersedes BS 7628BS EN 60044-5 IEC 60044-5 2004 Instrument transformers - Part 5: Capacitor voltage transformers Supersedes BS 3941BS EN 60044-6 IEC 60044-6 1999 Instrument transformers - Part 6: Requirements for protective current transformers for transient performanceBS EN 60044-7 IEC 60044-7 2000 Instrument transformers - Part 7: Electronic voltage transformersBS EN 60044-8 IEC 60044-8 2002 Instrument transformers - Part 8: Electronic current transformers

BS 923-1 IEC 60060-1 1990 Guide on High-voltage testing techniques - Part 1: General

BS EN 60060-2 1995 High-voltage test techniques - Part 2: Measuring systemsBS EN 60060-3 IEC 60060-3 2006 High-voltage test techniques - Part 3: Definitions and requirements for on-site testsBS EN 60071-1 IEC 60071-1 2006 Insulation coordination- Part 1: Definitions, principles and rulesBS EN 60071-2 IEC 71-2 1997 Insulation coordination- Part 2: Application guide Supersedes BS 5622-2BS EN 60076-1 IEC 60076-1 1997 Power transformers - Part 1: GeneralBS EN 60076-2 IEC 60076-2 1997 Power transformers - Part 2: Temperature rise Supersedes BS 171-2BS EN 60076-3 IEC 60076-3 2001 Power transformers - Part 3: Insulation levels, dielectric tests and external clearances in airBS EN 60076-5 IEC 60076-5 2001 Power transformers - Part 5: Ability to withstand short circuit Supersedes BS 171-5BS EN 60076-10 IEC 60076-10 2001 Power transformers - Part 10: Determination of sound levels Supersedes BS EN 60551BS EN 60076-11 IEC 60076-11 2004 Power transformers - Part 11: Dry-type transformers Supersedes BS EN 60726BS EN 60086-1 IEC 60086-1 2001 Primary batteries - Part 1: GeneralBS EN 60086-2 IEC 60086-2 2001 Primary batteries - Part 2: Physical and electrical specificationsBS EN 60086-4 IEC 60086-4 2000 Primary batteries - Part 4: Safety standard for lithium batteriesBS EN 60086-5 IEC 60086-5 2005 Primary batteries - Part 5: Safety of batteries with aqueous electrolyteBS EN 60298 IEC 60298 1996 A.C. metal-enclosed switchgear and controlgear for rated voltages above 1 kV and up to and including 52 kV Replaces BS 5227BS EN 60529 IEC 60529 1992 Degrees of protection provided by enclosures (IP code) Replaces BS 5490

BS EN 60664-1 IEC 60664-1 2003 Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests Replaces BS 7822BS EN 60871-1 IEC 60871-1 2005 Shunt capacitors for a.c. power systems having a rated voltage above 1000V - Part 1: GeneralBS EN 60896-11 IEC 60896-11 2003 Stationary lead-acid batteries - Part 11: Vented types - General requirements and methods of tests

BS EN 60931-2 IEC 931-2 1996

Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification

Rotating electrical machines - Part 7: Classification of types of construction, mounting arrangements and terminal box position (IM code)

Rotating electrical machines - Part 18: Functional evaluation of insulation systems - Section 21: Test procedures for wire-wound windings - Thermal evaluation and classification

Rotating electrical machines - Part 18-22: Functional evaluation of insulation systems - Test procedures for wire-wound windings - Classification of changes and insulation component substitutions

Rotating electrical machines - Part 18: Functional evaluation of insulation systems - Section 31: Test procedures for form-wound windings - Thermal evaluation and classification of insulation systems used in machines up to and including 50MVA

and 15 kV

Supersedes BS 923-3 & BS 923-4

Shunt power capacitors of the non-self-healing type for a.c. systems having a rated voltage up to and including 1 kV - Part 2: Ageing test and destruction test

A B C D E

229

230

231

232

233

234235

236

237

238

239240241242243244245246

247

248249250251252253254255256257258259260261262263264265

266

BS EN 60931-3 IEC 60931-3 1997BS EN 60947-1 IEC 60947-1 2004 Low-voltage switchgear and controlgear - Part 1: General rulesBS EN 60947-2 IEC 60947-2 2003 Low-voltage switchgear and controlgear - Part 2: Circuit breakersBS EN 61330 IEC 1330 1996 High-voltage/low-voltage prefabricated substations

BS EN 61386-1 IEC 61386-1 2004 Conduit systems for cable management - Part 1: General requirements Supersedes BS EN 50086-1

BS EN 61386-21 IEC 61386-21 2004 Conduit systems for cable management - Part 21: Particular requirements - Rigid conduit systemsBS EN 61663-1 IEC 61663-1 2000 Lightning protection - Telecommunication lines - Part 1: Fibre-optic installationsBS EN 61663-2 IEC 61663-2 2001 Lightning protection - Telecommunication lines - Part 2: Lines using metallic conductors

BS EN 62271-200 IEC 62271-200 2004 Supersedes BS EN 60298BS EN ISO 1461 1999 Hot dip galvanized coatings on fabricated iron and steel articles - Specifications and test methods Supersedes BS 729

BS EN ISO 2560 2005 Welding consumables - Covered electrodes for manual metal arc welding of non-alloy and fine grain steels - Classification Supersedes BS 499BS EN ISO 3506-1 1998 Mechanical properties of corrosion-resistant stainless steels fasteners - Part 1: Bolts, screws and studs Supersedes BS 6105BS EN ISO 3506-2 1998 Mechanical properties of corrosion-resistant stainless steels fasteners - Part 2: Nuts Suprsedes BS 6105

BS EN ISO 3506-3 1998BS EN ISO 3506-4 2003 Mechanical properties of corrosion-resistant stainless steels fasteners - Part 4: Tapping screws

BS EN ISO 3834-1 2005 Supersedes BS EN 729-1BS EN ISO 3834-2 2005 Quality requirements for fusion welding of metallic materials - Part 2: Comprehensive quality requirements Supersedes BS EN 729-2BS EN ISO 3834-3 2005 Quality requirements for fusion welding of metallic materials - Part 3: Standard quality requirements Supersedes BS EN 729-3BS EN ISO 3834-4 2005 Quality requirements for fusion welding of metallic materials - Part 4: Elementary quality requirements Supersedes BS EN 729-4

BS EN ISO 3834-5 2005BS EN ISO 9606-2 2004 Quality test of welders - Fusion welding - Part 2: Aluminium and aluminium alloys Supersedes BS EN 287-2

BS EN ISO 14122-1 2001

BS EN ISO 14122-2 2001 Safety of machinery - Permanent means of access to machinery - Part 2: Working platforms and walkways

BS EN ISO 14122-3 2001 Safety of machinery - Permanent means of access to machinery - Part 3: Stairways, stepladders and guard-rails

BS EN ISO 14122-4 2004 Safety of machinery - Permanent means of access to machinery - Part 4: Fixed laddersBS EN ISO 15607 2003 Specification and qualification of welding procedures for metallic materials - General rules Supersedes BS EN 288-1

BS EN ISO 15609-1 2004 Supersedes BS EN 288-2

BS EN ISO 15609-2 2001

BS EN ISO 15610 2003 Supersedes BS EN 288-5

BS EN ISO 15611 2003 Supersedes BS EN 288-6

BS EN ISO 15612 2004 Supersedes BS EN 288-7

Shunt power capacitors of the non-self-healing type for a.c. systems having a rated voltage up to and including 1 kV - Part 3: Internal fuses

Supersedes BS EN 50086-2-1

High-voltage switchgear and controlgear - Part 200: AC metal-enclosed switchgear and controlgear for rated voltages above 1 kV and up to and including 52 kV

Mechanical properties of corrosion-resistant stainless steels fasteners - Part 3: Set screws and similar fasteners not under tensile stress

Quality requirements for fusion welding of metallic materials - Part 1: Criteria for the selection of the appropriate level of quality requirements

Quality requirements for fusion welding of metallic materials - Part 5: Documents with which it is necessary to conform to claim conformity to the quality requirements of ISO 3834-2, ISO 3834-3 or ISO 3834-4

Safety of machinery - Permanent means of access to machinery - Part 1: Choice of a fixed means of access between two levels

Partially supersedes BS 5395-3 & BS 4592-1 to -5

Partially supersedes BS 5395-3 & BS 4592-1 to -5

Partially supersedes BS 5395-3 & BS 4592-1 to -5

Partially supersedes BS 5395-3 & BS 4592-1 to -5

Specification and qualification of welding procedures for metallic materials - Welding procedure specification - Part 1: Arc welding

Specification and qualification of welding procedures for metallic materials - Welding procedure specification - Part 2: Gas welding

Specification and qualification of welding procedures for metallic materials - Qualification based on tested welding consumables

Specification and qualification of welding procedures for metallic materials - Qualification based on previous welding experience

Specification and qualification of welding procedures for metallic materials - Qualification by adoption of a standard welding procedure

A B C D E

267

268269270

271

272

273274

275

276

277

278279

280

281

282

283284285

286

287

288

289

290

291

292

293

294

295

296

297

BS EN ISO 15613 2004 Specification and qualification of welding procedures for metallic materials - Qualification based on pre-production welding test Supersedes BS EN 288-8

BS EN ISO 15614-1 2004 Supersedes BS EN 288-3

BS EN ISO 15614-2 2005 Supersedes BS EN 288-4BS IEC 60076-8 IEC 60076-8 1997 Power transformers - Part 8:Application guide

PD IEC TR 60071-4 2004 Insulation coordination - Part 4: Computational guide to insulation co-ordination and modelling of electrical networksBS 1377-1 1990 Methods of test for Soils for civil engineering purposes - Part 1: General requirements and sample preparation

BS 1449-1.1 1991 Steel plate, sheet and strip - Part 1: Carbon and carbon-manganese plate, sheet and strip - Section 1.1 General specification

BS 1449-1.8 1991

BS 1449.14 1991

BS 1924-1 1990

BS 1924-2 1990 Stabilized materials for civil engineering purposes - Part 2: Methods of test for cement-stabilized and lime stabilized materialsBS 4168-7 1982 Hexagon socket screws and wrench keys: metric series - Part 7: Specification for hexagon socket shoulder screwsBS 5930 1999 CoP for site investigations Supersedes BS 5931

BS 6121-1 2005 Mechanical cable glands - Part 1: Armour glands - Requirements and test methodsBS 6121-5 2005 Mechanical cable glands - Part 5: CoP for selection, installation and inspection of cable glands and armour glandsISO 10474 1992 Steel and steel products - Inspection documents

BS EN 10020 2000 Definition and classification of grades of steel

ISO 14692-1 BS EN 14692 2002ISO 14692-2 2002 Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 2: Qualification and manufacture ISO 14692-3 2002 Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 3: System design

ISO 14692-4 2002 Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 4: Fabrication, installation and operationBS PD CR ISO 17663 2001 Welding - Guidelines for quality requirements for heat treatment in connection with welding and allied processes

BS 5839-1 2002

BS 5839-3 1988BS 5839-5 1988 Fire detection and fire alarm systems for buildings - Part 5: Specification for optical beam smoke detectors

BS 5839-6 2004

BS 5839-8 1988

BS 5839-9 2003

BS EN 10216-1 2002

BS EN 10216-2 2002

Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 1: Arc and gas welding of steels and arc welding of nickel and nickel alloys

Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 2: Arc welding of aluminium and its alloys

Steel plate, sheet and strip - Part 1: Carbon and carbon-manganese plate, sheet and strip - Section 1.8 Specification for hot rolled narrow strip based on formability

Steel plate, sheet and strip - Part 1: Carbon and carbon-manganese plate, sheet and strip - Section 1.14 Specification for hot rolled narrow strip supplied in a range of conditions for heat treatment and general engineering purposes

Stabilized materials for civil engineering purposes - Part 1: General requirements, sampling, sample preparation and tests on materials before stabilization

Read in conjunction with BS EN 50262

Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 1: Vocabulary, symbols, applications and materials

Fire detection and fire alarm systems for buildings - Part 1: CoP for system design, installation, commissioning and maintenance

Fire detection and fire alarm systems for buildings - Part 3: Specification for automatice release mechanisms for certain fire protection equipment

Fire detection and fire alarm systems for buildings - Part 6: CoP for the design, installation and maintenance of fire detection and fire alarm systems in dwellings

Fire detection and fire alarm systems for buildings - Part 8: CoP for the design, installation, commissioning and maintenance of voice alarm systems

Fire detection and fire alarm systems for buildings - Part 9: CoP for the design, installation, commissioning and maintenance of emergency voice communication systems

Seamless steel tubes for pressure purposes - Technical delivery conditions - Part 1: Non-alloy steel tubes with specified room temperature properties

Replaces BS 3601 & BS 3059-1

Seamless steel tubes for pressure purposes - Technical delivery conditions - Part 2: Non-alloy and alloy steel tubes with specified elevated temperature properties

Replaces BS 3059-2, BS 3602-1, BS 3604-1, BS

3606

A B C D E

298

299

300

301302303

304

305

306

307

308

309310

311

312313314

315

316317

318

319

320

321

322

323

324

325

326

327

BS EN 10216-3 2002 Seamless steel tubes for pressure purposes - Technical delivery conditions - Part 3: Alloy fine grain steel tubes

BS EN 10216-4 2002 Supersedes BS 3603

BS EN 10217-1 2002

BS EN 10217-2 2002BS EN 10217-3 2002 Welded steel tubes for pressure purposes - Technical delivery conditions - Part 3: Alloy fine grain steel tubes Supersedes BS 3602-2

BS EN 10217-4 2002 Supersedes BS 3603

BS EN 10217-5 2002 Supersedes BS 3602-2

BS EN 10217-6 2002BS EN ISO/IEC 17020 2004 General criteria for the operation of various types of bodies performing inspection Replaces BS EN 45004

PD 5500 2003 Specification for Unfired pressure vessels Superseded by 2006 rev.BS 7541 1992 Spec for Temporary protectivess for the protection of metal surfaces against corrosion during transport and storage Proposed for withdrawal

BS EN 3-3 1996 Portable fire extinguishers - Part 3: Construction, resistance to pressure, mechanical tests Supersedes BS 5423

BS EN 3-6 1996 Supersedes BS 5423

BS EN 3-7 2004 Portable fire extinguishers - Part 7: Characteristics, performance requirements and test methodsBS EN 54-1 1996 Fire detection and fire alarm systems - Part 1: Introduction Supersedes BS 5445 -1BS EN 54-2 1998 Fire detection and fire alarm systems - Part 2: Control and indicating equipment Supersedes BS 5839-4BS EN 54-3 2001 Fire detection and fire alarm systems - Part 3: Fire alarm devices - SoundersBS EN 54-4 1998 Fire detection and fire alarm systems - Part 4: Power supply equipment Supersedes BS 5839-4BS EN 54-11 2001 Fire detection and fire alarm systems - Part 11: Manual call points Supersedes BS 5839-2

BS EN 932-1 1997 Tests for general aggregates - Part 1: Methods for sampling Will supersede BS 812-102

BS EN 933-3 1997 Tests for geometrical properties of aggregates - Part 3: Determination of particle shape - Flakiness index Will supersede BS 812-105BS EN 1677-5 2001 Components for slings - Safety - Part 5: Froged steel lifting hooks with latch - Grade 4 Supersedes BS 2903BS EN 12077-2 1999 Cranes safety - Requirements for health and safety - Part 2: Limiting and indicating devicesBS EN 50262 1999 Cable glands for electrical installations

BS EN 60146-1.1 IEC 60146-1-1 1993 Supersedes BS 4417

BS EN 60146-1-3 IEC 60146-1-3 1993 Semiconductor convertors - General requirements and line commutated convertors - Part 1-3: Transformers and reactors Supersedes BS 4417BS EN 60146-2 IEC 60146-2 2000 Semiconductor convertors - Part 2: Self-commutated semiconductor convertors including direct d.c. convertors

BS EN ISO 4026 2003 Hexagon socket set screws with flat point Supersedes BS 4168-2BS EN ISO 4027 2003 Hexagon socket set screws with cone point Supersedes BS 4168-3BS EN ISO 4028 2003 Hexagon socket set screws with dog point Supersedes BS 4168-4BS EN ISO 4029 2003 Hexagon socket set screws with cup point Supersedes BS 4168-5BS EN ISO 4762 2004 Hexagon socket head cap screwsBS EN ISO 7380 2004 Hexagon socket button head screws

BS EN ISO 10440-1 2001

Seamless steel tubes for pressure purposes - Technical delivery conditions - Part 4: Non-alloy and alloy steel tubes with specified low temperature properties

Welded steel tubes for pressure purposes - Technical delivery conditions - Part 1: Non-alloy steel tubes with specified room temperature properties

Supersedes BS 3601 & BS 3059

Welded steel tubes for pressure purposes - Technical delivery conditions - Part 2: electric welded non-alloy and alloy steel tubes with specified elevated temperature properties

Supersedes BS 3602-1, BS 3604-1, BS 3606, BS 3059-

2

Welded steel tubes for pressure purposes - Technical delivery conditions - Part 4: Electric welded non-alloy steel tubes with specified low temperature properties

Welded steel tubes for pressure purposes - Technical delivery conditions - Part 5: Submerged arc welded non-alloy and alloy steel tubes with specified elevated temperature properties

Welded steel tubes for pressure purposes - Technical delivery conditions - Part 6: Submerged arc welded non-alloy steel tubes with specified low temperature properties

Portable fire extinguishers - Part 6: Provisions for the attestation of conformity of portable fire extinguishers in accordance with EN 3 Part 1 to Part 5

Supersedes EN 3-1, 3-2, 3-4, 3-5

Semiconductor convertors - General requirements and line commutated convertors - Part 1-1: Specifications of basic requirements

Petroleum and natural gas industries - Rotary-type positive displacement compressors - Part 1: Process compressors (oil-free)

A B C D E328

329

330

331

332

333

334

335

336337338339

340

341

342343344345346

347

348

349350351

352

353

354355356357358359360

361

BS EN ISO 10440-2 2001BS EN ISO 10642 2004 Hexagon socket countersunk head screws

Petroleum and natural gas industries - Rotary-type positive displacement compressors - Part 2: Packaged air compressors (oil-free)

A B C D E

362

363

INDEX FOR CODES AND STANDARDS(this sets has not been entered on the standard index)Standard No. Dual No. ref. Year/Edition Title Remarks

ASME B16.34a 1998 Valves-Flanged, Threaded and Welding EndAPI Standard 650 1998 Welded Steel tanks for oil storageAPI Standard 610 2003 Centrifugal pumps for Petroleum, Petrochemical and Natural Gas IndustriesASME B36.10M 2000 Welded and seamless wrought steel pipe

API Standard 2000 1998 Venting atmospheric and low-pressure storage tanks-Nonrefrigerated and Refrigerated

D 2992-01 2001BS 812-124 1989 Testing Aggregates-Part 124: Method for determination of frost-heaveBS 812-123 1999 Testing Aggregates-Part 123: Method for determination of alkali-silica-reactivity-concrete prism methodBS 812-121 1989 Testing Aggregates-Part 121: Method for determination of soundnessBS 812-119 1985 Testing Aggregates-Part 119: Method for determination of acid-soluble material in fine aggregateBS 812-117 1988 Testing Aggregates-Part 117: Method for determination of water-soluble chloride saltsBS 812-114 1989 Testing Aggregatesk-Part 114: Method for determination of the polished-stone valueBS 812-113 1990 Testing Aggregates-Part 113: Method for determination of Aggregate Abrasion Value (AAV)BS 812-112 1990 Testing Aggregates-Part 112: Method for determination of Aggregate Impact Value (AIV)BS 812-111 1990 Testing Aggregates-Part 111: Methods for determination of Ten per cent Fines Value (TFV)BS 812-110 1990 Testing Aggregates-Part 110: Methods for determination of Aggregate Crushing Value (ACV)BS 812-109 1990 Testing Aggregates-Part 109: Methods for determination of moisture contentBS 812-106 1985 Testing Aggregates-Part 106: Method for determination of shell content in coarse aggregateBS 812-104 1994 Testing Aggregates-Part 104: Method for qualitative and quantitative petrographic examination of aggregatesBS 812-100 1990 Testing Aggregates-Part 100: General requirements for apparatus and calibrationBS 812-102 1989 Testing Aggregates-Part 102: Methods for samplingBS 812-2 1995 Testing Aggregates-Part 2: Methods of determination of density

BS 812-105.1 1989 Testing Aggregates-Part 105: Methods for determination of particle shape-Section 105.1: Flakiness index

BS 812-105.2 1990 Testing Aggregates-Part 105: Methods for determination of particle shape-Section 105.2: Elongation of coarse aggregateBS 812-103.1 1985 Testing Aggregates-Part 103: Methods for determination of particle size distribution-Section 103.1: Sieve TestsBS 812-103.2 1989 Testing Aggregates-Part 103: Methods for determination of particle size distribution-Section 103.2: Sedimentaion Test

Standard practice for-obtaining hydrostatic or pressure design basis for "Fiberglass" (Glass-Fiber-Reinforced Thermosetting Resin) PIPE and FITTINGS1,2

A B C D E12345678

9

1011121314151617181920212223242526

27

2829

INDEX FOR CODES AND STANDARDSStandard No. Dual No. ref. Year/Edition Title Remarks

BS 6954-1 ISO 3443/1 1988 Tolerances for building - Part 1 Recommendations for basic principles for evaluation and specBS EN 10020 2000 Definition and classification of grades of steel

API 608-3 2002 Metal Ball valves - Flanged, Threaded, and Welding ends

ANSI/AWWA C950-01 2002 Fiber glass pressure PipeANSI/AWWA C540-02 2003 Power - Actuating devices for valves and Slide GatesANSI/AWWA C510-97 1998 Double Check valve Backflow Prevention assemblyANSI/AWWA C512-04 2004 Air-Release , Air Vaccum and combination Air Vlvs for waterworks service

ASME B30.17 2003 Overhead and Gantry Cranes ( Top Running Bridge ,Single Girder, underhung Hoist)ASME B30.16 2003 Overhead Hoists (Underhung)ASME C30.10 2005 Hooks - Safety std for Cableways, Cranes, Derricks, hoists, hooks, jacks and SlingsASME B73.2 2003 Specification for vertical in-line Centrifugal Pumps for Chemical Process

ISO 10474 1992 Steel and Steel Products - inspection Docs

ASTM D 2992-01 Standard Practice for Obtaining Hydrostatic or Pressure design basis for FibreglassASTM D 3517-04 Standard Specification for Fiberglass

NFPA 10 2007 Standard for Portable Fire ExtinguishersNFPA 11 2005 Standard for Low, Medium and High Expansion FoamNFPA 12 2005 Standard on Carbon Dioxide Extinguishing SystemsNFPA 13 2007 Standard for the installation of Sprinkler SystemsNFPA 15 2007 Standard for Water Spray Fixed Systems for Fire ProtectionNFPA 20 2007 Standard for the installation of stationery pumps for Fire ProtectionNFPA 22 2003 Standard for Water Tanks for private fire protection NFPA 24 2007 Standard for the Installation of Private Fire Service Mains and their AppurtenancesNFPA 70 2005 National Electrical CodeNFPA 72 2007 National Fire Alarm Code

A B C D E12345678910111213141516171819202122232425262728293031323334