Bank of Baroda · 32. Alarm bell. 33. G.I. pipe 34. Steel conduits ... BEC / SUPREME / AKG BEC /...

1

2.

3.

4.

5.

6.

7.

1.

2.

3.

Bank of Baroda, West Bengal, Sikkim & A & N Island invites sealed tenders in two bid system for the

proposed interior & electrical work of Dakshin Barasat Branch, Vill-Beledanga, P.O -, Dakshin Barasat,

P.S. - Joynagar, Dist - 24 Pgs(S), West Bengal. Pin-743372. The work is to be completed within 2(Two)

weeks.

(Government of India Undertaking)

NOTICE INVITING TENDER

Interested agencies having experience in work of similar nature & magnitude and fulfilling the eligibility

criteria given below may download detailed tender document from Bank's Website

http:bankofbaroda.com

Part 'A' envelope (Technical Bid) shall contain : Earnest Money, the documents for satisfying eligibility

criteria & the technical & financial stipulation, if any, of the tenderer & Part 'B' shall contain : financial

bid along with a copy of the tender document, duly signed in all pages both shall be separately sealed

& submitted in another sealed envelope to the Deputy. General Manager, Bank of Baroda, West

Bengal, Sikkim & A & N Island, BARODA TOWER, Plot No. 38/2, Block GN, Sector-V, Salt Lake City, Kolkata : 700

091, by 3 P.M. on 12.06.2012 along with Earnest money amounting to Rs. 11,000/- by Bank Draft / Pay

order in favour of Bank of Baroda shall be submitted in Part 'A'.

Part 'A' will be opened at 3.30 p.m.. on 12.06.2012.

Part 'B' of the tenders will be opened for those only who fulfils the qualifying criteria given in the tender

document. The unopened part 'B' along with Earnest Money deposit for those not fulfilling qualifying

criteria will be returned.

Clarifications, if any, required on drawings, schedules, specifications, etc. can be obtained from our

Consultant M/s. Dearch Architects Pvt Ltd, 101, Madurdaha, Kolkata - 700107, Phone no - 9830018243 ,

9836544297.

The Bank reserves the right to summarily reject any or all application without assigning any reason there

for.

MINIMUM ELIGIBILITY CRITERIA (Shall be submitted with Part A of the Offer)

The tenderer should have completed in last three Financial years (i.e. current year & two previous

financial year) in Bank, Govt. or Govt. undertaking and Financial Institutions, Corporate Sectors, etc.

minimum 3 (three) similar composite work (Interior Furnishing & Electrical) costing not less than Rs. 22.00

lacs in single contract. (Work order & completion Report in support must be submitted & marked

annexure-I)

The total contract amount received by the Tenderer during the last 3 financial years should be minimum

as 40.00 lacs per year in contract work. In support of this the Tenderer should submit audited sheet duly

Certified by the Chartered Accountant & marked annexure-II.

The Tenderer should produce Solvency Certificate from any Nationalised / Scheduled Bank for an

amount of 200% of the advertised Tender value marked annexure-III.

Bank of Baroda

1

4.a) The Tenderer shall furnish copies of :

i) IT Registration Certificate with No.

ii) Sales Tax Registration Certificate with No.

iii) Service Tax Registration Certificate with No.

iv) Electrical Contractor's License with No.

v) Electrical Supervisor’s License with No.

5.

a)

b)

c)

d)

e)

- marked annexure - IV

- marked annexure - V

- marked annexure - VI

- marked annexure - VII

- marked annexure - VIII

The Tenderer should also submit the following documents along with the Tender.

List of technical persons available on hand, years of their association with the firm & proposed to be

engaged for the subject work, if selected (marked annexure-IX) ;

List of important plant & machinery available on hand (own) and proposed to be inducted (own & hired

to be given separately) for carpentry & electrical work (marked annexure-X)

List of works completed in the last (three) financial years under Bank / Govt., Semi - Govt. Govt.

undertaking / Corporate Sectors giving description of work, organisation for whom executed,

approximate value of contract at the time of award, date of award and date of scheduled completion

of work, date of actual completion and final value of contract should also be given (marked annexure-

XI)

List of works in hand indicating description of work, contract value, approximate value of balance work

yet to be done and date of award (marked annexure-XII)

Tenderer who will quote the rate must have a local office at Kolkata. This is absolutely essential for day

to day supervision & coordination of the work at site.

All informations are to be fully authenticated & documented failing which the documents submitted will not be

accepted.

2

1.

2.

3.

4.

5.

6.

7

8.

9.

10.

11.

Contractors will be required to arrange for their own storing. Dismantled materials are to be carted

away from site at own cost and disposed of in conformity with Municipal regulations.

The quoted rates, are to include cost of all materials, labour and or any other material, all statutory

taxes, transport, handling delivery at site and installation, complete in all respect, as per drawing,

directions or instructions of Employer/Consultant. The quoted rates are also to include dismantling of

partitions, counters, old electrical wirings etc. and stacking serviceable materials and disposal of debris,

etc.

Prior approval of the Employer/ Consultant shall be obtained for colour and thickness of laminates to be

used in the work.

GENERAL TERMS & CONDITIONS

The tenderer are to visit the site and acquaint themselves with site conditions before quoting rates.

The arrangement for “ Wire Management " is to have prior approval of the Client.

The quoted rates shall remain firm during the entire currency of contract. No price variation for any

causes whatsoever, shall be entertained.

The time of completion shall be two (2) weeks from the date of placement of order.

The offer shall remain valid for acceptance for a period of 30 days from the date of submission of

offer.

Tenders addressed to Deputy General Manager, Bank of Baroda, West Bengal & Sikkim Region and

submitted at his office at BARODA TOWER, Plot No. 38/2, Block GN, Sector-V, Salt lake City, Kolkata : 700

091, by 3 P.M. on 12.06.2012, accompanied by Earnest Money amounting to Rs. 11,000/- by Bank draft

payable to Bank of Baroda and other documents as mentioned in NIT. Part 'A' of the tenders will be

opened at 3.30 P.M. on the same date.

Payments will be made once on completion by the Employer within 15 days after certification of bill by

the Consultant 10% of the total payable amount is to be retained as retention money and will become

due for release after expiry of six months from the date of completion of the installation & subject to

satisfactory maintenance of the executed work.

The Employer reserves the right to themselves to accept or reject any or all offers without assigning any

reason therefor.

3

SPECIFICATION OF MATERIALS FOR INTERIOR WORK

Sl.No. Description

1. Laminate

2. Ply & Block Board

3. Glass

4. False Ceiling & Accessories

5. Veneer

6. Textured Wall Paint

7. Glue

8. Locks

9. Aluminium Hardware Fittings Metako / Allen / Crown with ISI Mark

10. Brass Hardware

11. Floor Spring

12. Screws

13. Casters

14. Sliding Drawers / Channels

15. Furnishing Fabric

16. Leather Foam

17. PVC Flooring

18. Carpet

Brass Arts / Vijoy

Evrite Agencies Pvt. Ltd. / Nita Floor Spring

Nettle Fold

Glamour or Favourite (Balla Industries)

Make (s)

Woven type "Harmony" range from "Vimal" or

equivalent

Bhor Industries or equivalent

Armstrong / Krishna / Premier

Marino / Greenlam / Century / Archid

Green / Century / Archid / Austin

Modi / Indo Ashahi / Float Glass India Ltd.

Efficient Gadjets

India Gypsum Ltd.

Earl Behari / Efficient Gadjets

Durian / Century / Archid

ICI, Jenson & Nicholson / Asian paint / Berger

ICI, Spectrum, Heritage

Godrej / Secur / Yale

4

SPECIFICATIONS OF MATERIALS FOR ELECTRICAL WORK

Sl.No. Description

1. Switch fuse / fuse switch units (HRC) (32A TPN &

above)

2. Timer (TSQ 100)

3. Voltmeter & Ammeter

4. Voltmeter & Ammeter selector switches

5. Phase indicating lamp

6.

7. Capacitor

8. HRC fuses

9. Power Cable : XLPE

10.

11. HRC fuse base & carriers.

12. PVC terminals

13. 1.1 KV grade PVC insulated armoured

aluminium cable (ISI marked)

14. 1.1KV 660V grade PVC insulated & sheathed /

insulated copper wire & flexible cords (ISI

marked).

15. Moulded case circuit breaker

16. RCCB / ELCB

17. Switch fuse with rewirable fuses. (6A & 32A TPN)

18. Isolator

19. Changeover switch (on load type)

GE power / SIEMENS / L&T / Schneider

A. E. / IMP

Make (s)

L & T

NATIONAL/FINOLEX/ HAVELLS

KAYCEE / L & T

CROMPTON/SIEMENS

TATA LEVERT/NEUMERIC/ KIRLOSKAR

GLOSTER/INCAB/POLYCAB/CINOLEX

GE power / SIEMENS / L & T / SCHNEIDER

Vaishno / SIEMENS / ROSS controls

A E / KAPPA SEGC & CONTROLS / CONTROL

SWITCHGEAR

GE Power/SIEMENS/L&T/SCHNEIDEV

UNIVERSAL / GLOSTER / NATIONAL / NICCO /

FINOLEX/HAVELL'S

L & T / SCHNEIDER/LEGRAND

HAVELL’S / STANDARD

HAVELL’S / STANDARD

LEGRAND/ SIEMENS / L&T

ELMEX / ESSEN

KENBAR / HAVELLL’S / ELCON / HPL /

CONTROL & SWITCHGEAR.

5

Sl.No. Description

20. MCB distribution board

21. Distribution fuse board with rewireable fuses

22. Miniature circuit breaker / MCB type isolator

23. Contractors

24. Auxiliary contractor

25. 1/16 Amp Piano key type switch / flushed type

plug socket

26. 6/16 Amp modular switch / socket, module

plate & mounting M.S. / PVC box.

27. 300W, 2 module electronic regulator

28. Ceiling rose

29. Holder

30. Buzzer / call bell

31. Luminous indicating type buzzer with

cancellation push.

NATIONAL / HOMA / EQUIVALENT

32. Alarm bell.

33. G.I. pipe

34. Steel conduits (conforming to IS in all respects)

35. Black enamelled

36. Galvanised

BAJAJ / ANCHOR / NATIONAL / HOMA

KAY / EPP / ANCHOR / JJ

Good local make with minimum wall thickness of 3

mm. for 19 / 20 mm. and 25mm sizes & 2.5 mm. for

12mm. sizes

BEC / SUPREME / AKG

BEC / SUPREME / AKG

BST / BANSAL

KHERAJ / GETCO

HAVELL’S / BPC / BOSMA

KAY / EPP / ANCHOR / JJ

CPL (Genius) / ANCHOR (Roma) / CRABTREE /

MK

ANCHOR (Roma) / CRABTREE / MK

ANCHOR / PRECISION / SSK & RIDER

SIEMENS / L & T/BCH

SIEMENS / L & T

LEGRAND / SIEMENS

Make (s)

LEGRAND/ SIEMENS

6

Sl.No. Description

37. Non-metallic PVC conduit pipe

38. Compression type brass gland

39. Cable termination socket

40. Light fitting & lamps

41. Decorative/Ornamental /Chandelier / Light

Fittings

42. Ceiling Fan

43. Exhaust fan

44. Industrial type socket & top

45. Telephone wire

46. Telephone Socket

47. Network Cable

48. Contractors

49. STARTERS

Make (s)

NORTH WEST / CABTREE

CROMPTON / POLAR / KHAITAN

HAVELL’S / CROMPTON / LEGRAND

FINOLEX / RRK/NATIONAL

CRABTREE/MK

CROMPTON / POLAR / KHAITAN / EPC

PLAZA / KALINGA/ PRECISION/AKG or

equivalent

L & T / SIEMENS

CROMPTON / POLAR / KHAITAN

FINOLEX or equivalent

DOWELL'S

WIPRO or equivalent

DOWELLS / JOHNSON / COMET

7

BANK OF BARODA - DAKSHIN BARASAT DEARCH ARCHITECTS (PVT) LTD.

SL.

NO.ITEM OR DESCRIPTION UNIT QUANTITY RATE AMOUNT

1 PARTITIONS:-

NOTE:

A. The rate for wooden partition or cladding will include for making out outlets

of appropriate sizefor electrical, telephone and computer terminals wherever

required. The surface of the electrical boxes if any shall be hidden/ flushed

with veneer work according to design.B. All wooden framework for partition or any allied work shall be free from large

knots, cracks, saps and other defects and to be treated with two coats of

solignum paint. Timbers shall be of specified quality and approval of competent

authority shall be obtained before fixing the framework.C. All plywood shall be of BWP grade and blockboard shall be BWP.

D. All door frames and members of the partition walls to be fixed securedly

with RCC, ceiling and floor.E. All framework shall be of sesoned malaysian sal wood unless otherwise

mentioned.

a Full Height Solid Partition :-

Supplying and erecting full height partly glazed partition (8'-6" height) as per

drawing and conforming to the following specification Basic Framework:- Full height Solid partition with Malaysian Sal wood frame of

C.S size 2" x 2" at required spacing but not exceeding than 2'-0" x 2'-0". The

framework shall be treated with two coats of wood preservative and fire

retardant material

Skin Membrane:- The skin shall comprise of a covering of 6mm thick BWR

grade plywood

Finishing:- 1mm thick laminate of prescribed shade on both sides. The groove

between two laminate joint shall not exceed 1.0 mm as or otherwise specified by

the architect. Skirting:-

The skirting shall be 6" high and 2 " thick finished with prescribed shade of

laminate as per design. Rate shall

also include providing cutouts and provisions to run electrical conduits, switches

SFT 270.00

b Low Height Partially Glazed Partition :-

Supplying and erecting full height partly glazed partition (4'-0" & 5'-0" height)

as per drawing and conforming to the following specification. Basic Framework :- Malaysian Sal wood frame of C.S size 2" x 2" at required

spacing but not exceeding than 2'-0" x 2'-0". All the framework shall be coated

with two coats of wood preservative and Fire Retardant material.

Skin Membrane :- The opaque portion of the partition (3'-0" from the finished

floor level) as per design shall be covered with BWR grade 6 mm thick ply on

both sides of the partition.

BUDGETARY ESTIMATE OF FURNISHING WORK FOR BOB - DAKSHIN BARASAT BRANCH


Finishing :-The opaque portion shall be covered with 1mm thick laminate of the

prescribed shade .The groove between two laminates shall be not more than

1mm. Skirting:-

The skirting shall be 6 " high and 2 " thick covered with BWR grade 6 mm thick

ply and finished with the prescribed shade of laminate.

Glazing:- The transparent parts of the partition shall comprise of 12 mm thick

clear glass (etched as per design) tightened in place with teakwood glazing bead

of approved shape and polishing the same with wood polish of mahogany colour

as per the instruction of the architect. In case of Cash counters the glass shall

have hole for transaction of money and papers.

Edge Moulds:- All free top/ end surfaces shall have teakwood moulds of

approved shape (80 x 25 mm C.S) finished with wood polish of mahogany colour. Rate shall include providing cutouts and provisions to run electrical conduits, switches etc. It shall also include the etching, polishing and making holes in the glass if any.The thickess of the partition may vary as per design and the rates shall include the changes in the thickness as well

SFT 150.00

c Low Height Partially Glazed Partition (for cash counters) :-

Supplying and erecting full height partly glazed partition (6'-0" height) as per

drawing and conforming to the following specification. Basic Framework :- Malaysian Sal wood frame of C.S size 2" x 2" at required

spacing but not exceeding than 2'-0" x 2'-0". All the framework shall be coated

with two coats of wood preservative and Fire Retardant material.

Skin Membrane :- The opaque portion of the partition (3'-0" from the finished

floor level) as per design shall be covered with BWR grade 6 mm thick ply on

both sides of the partition.

Finishing :-The opaque portion shall be covered with 1mm thick laminate of the

prescribed shade .The groove between two laminates shall be not more than

1mm. Skirting:-

The skirting shall be 6 " high and 2 " thick covered with BWR grade 6 mm thick

ply and finished with the prescribed shade of laminate.

Glazing:- The transparent parts of the partition shall comprise of 12 mm thick clear glass (etched as per design) tightened in place with teakwood glazing bead of approved shape and polishing the same with wood polish of mahogany colour as per the instruction of the architect. In case of Cash counters the glass shall have hole for transaction of money and papers.

SFT 200.00

2 PANELLING FOR WALLS AND FREE STANDING PILLARS:-

a

bColumn Encasing (upto false ceiling level) works as per drawing and conforming

to the following specification: SFT 100.00


Basic Framework:- Well seasoned Malaysian Sal wood Sections treated with

two coats of wood preservative and Fire retardant material of cross section

size 2" x 1" at horizontal and vertical spacing of not more than 2'-0" x 2'-0"

c/c. Skin

Membrane:- Providing and fixing 6 mm thick plywood of BWR grade as per

drawing/ instruction.

Finishing:- 1 mm thick laminate of same or combination shades as per drawing or

instruction and groove not more than 1 mm.

Skirting :- Providing and fixing of Malaysian Sal of size 6" x 1" C.S and

membraning the same with 4 mm thick plywood of BWR grade and finishing it

with 1 mm thick laminate of same or combination shade as per instruction/

drawing. Rate

shall also include providing cutouts and provisions to run electrical conduits,

c

Encasement area for entrance doors and columns with Aluminium Composite

panel. Company : Alstone. Till 2'-6" Height Colour Code VL-07/VL-04. Colour

Above 2'-6" Height till the false ceiling level Colour Code VL-03 (For the

Columns). For the Door Encasement Colour Code VL-03. All the Aluminium

Composite panelling needs to be done with required Aluminium Framework.

SFT 100.00

3 DOORS:-

a

Solid Flush Door:- Supplying and fixing in position overall 37 mm thick solid

core hot pressed phenol formaldehyde bonded approved flush door shutter

finished with 1 mm thick laminate sheet of approved shade and colours with a

groove of not more than I mm in case of two different laminates colours. The

rates shall include the cost of door frame, hardware, bolt, locks, hinges, handles

etc.

i)Blocked door in entry toToilet area, Pantry & Store Room with vision panel (3'-

0"x7'-0")NO 3.00

`

ii)Entry door to cash and Teller counter door without etching ( 3'-0" & 2'-3" x 6'-

0")NO 3.00

iii) Entry door to UPS & Managar room without etching ( 3'-0" x 5'-0") NO 2.00

b

Glazed Main Door:- Providing and fixing in position of single leaf door shutter

made out of 12 mm thick float glass etched as per design. The other side of the

door shall have fixed glass as per design. The door shall rotate on floor springs

of ISI make on which the shutters shall be pivoted at top and bottom. Door

handles shall of H-type of satin finish stainless steel handlesThe rates shall

include cost of door frame, hardware, bolt, locks, hinges, handles etc. Door size:

4'-0" x 7'-0". The rates shall include etching the Bank's logo and emblem on the

glass in the size and design as prescribed by the architect.

Nos. 1.00


4 FURNITURES:-

a

Providing and fixing of officer/ CSR desk made out of 19 mm thick BWP grade

ply. The top shall be 25 mm thick finished with prescribed shade of laminate. All

drawers and shelves shall be of 12 mm thick ply. All exposed surface shall be of

the prescribed shade of laminates 1 mm thick and the internal portions of

drawers and cabinets shall be done with 0.8 mm thick white laminates. Each

table shall have one drawer of 4" height and 1'-6 " wide and a tea tray above

that as well as a shelved and shutter cabinet below that . The table shall have

space for CPU tray (INNOFITT systems or similar) and keyboard tray

(INNOFITT systems or similar) as per design. The table size is of 5'-0" x 2'-6".

The height shall be 2'-6" standard. Placement of drawers and shelves shall be as

per design. All the ply edges shall be lipped and finished with prescribed shade

of polish . The rate shall also include the cost for hardwares like hinges,

towerbolts, handles, magnets, wire manager etc.

Nos. 1.00

b

Providing and fixing of Branch Manager's table made out of 19 mm thick BWP

grade ply. The top shall be 25 mm thick with prescribed shade of laminate All




table shall have one drawer of 4" height and 1'-6" wide with a tea tray above

and a shelved and shutter cabinet below that . The table shall have CPU tray

(INNOFITT system or equivalent) and keyboard tray (INNOFITT System or

similar). The table size is of 5'-6" x3'-0". The height shall be 2'-6" standard.

Placement of drawers and shelves shall be as per design. The side unit shall be

3'-0" in length and 1'-6" wide with the standard height of 2'-6". The side unit

shall have shelves beneath with sliding shutters.All the ply edges shall be lipped

and finished with prescribed shade of polish . The rate shall also include the

Nos. 1.00

c

Providing and fixing of clerical desk made out of 19 mm thick BWP grade ply.

The top shall be 25 mm thick finished with prescribed shade of laminate. All




table shall have one drawer of 4" height and 1'-6 " wide and a tea tray above

that as well as a shelved and shutter cabinet below that . The table shall have

space for CPU tray (INNOFITT systems or similar) and keyboard tray

(INNOFITT systems or similar) as per design. The table size is of 4'-0" x 2'-

0"". The height shall be 2'-6" standard. Placement of drawers and shelves shall

be as per design. All the ply edges shall be lipped and finished with prescribed

shade of polish . The rate shall also include the cost for hardwares like hinges,

towerbolts, handles, magnets, wire manager etc.

Nos. 2.00


d

Providing and fixing of Cash Counters made out of 19 mm thick BWP grade ply.

Working counter side : The Height of this side shall be 2'-6" All drawers and

shelves shall be of 12 mm thick ply. All exposed surface shall be of the

prescribed shade of laminates 1 mm thick and the internal portions of drawers

and cabinets shall be done with 0.8 mm thick white laminates. Each table shall

have set of 3 drawers1'-6" width on slide channels on one side . The table shall

have CPU tray on the other side and a keyboard tray (INNOFITT system or

similar). The table size is of 4'-0" x2'-0". The portion projecting on the

customer side shall be 10 " deep and have intermediate shelf 12 mm thick shall

have 2 sets of sliding shutter and a locking arrangement for keeping currency

note. customer

transaction side: The top shall be at a finished of (ht. 3'-8") , 1'-6" wide and

projecting 6" on the customer side. This top shall be finished with 18 mm thick Granite(Red) moulded as per instruction above a 25 mm ply and the total height includes this granite top. The space between the working counter side and customer transaction side is utilized from the working side for keeping currency notes. The panel thus framed shall be finished with 1 mm thick laminate from outside and completed as per the instruction of the architect.

All the ply edges shall be lipped and finished with prescribed shade of polish and

the glass edge shall be polished and bevelled. The rate shall also include the cost

for hardwares like hinges, towerbolts, handles, magnets, wire manager etc. Note

that the portion above the 3'-8" partition shall have glass with a hole for money

and paper transaction.

RFt. 10.00

e

Providing and fixing writing ledge consisting of 25 m thick BWP grade ply at

base finished on all faces with 1 mm thick laminate, 5 mm thick glass partitions

at approx 150 mm c/c fixed on base with D brackets for keeping withdrawal/

deposit forms and 8 mm thickened toughened glass on top with help of studs all

complete as per drawings (approx width 300 mm). A cheque drop box of size 2'

x 2' x 6" with 1" wide slit for inseting cheques made of 19 mm thick BWP grade

ply finished with 1 mm thick laminate of prescribed shade. The inside of the box

shall be painted with prescribed shade.

Nos. 1.00

f

Providing and fixing of low height storages (height till 2'-6") made out of 19

mm thick BWR grade ply finished with 1 mm thick laminate outside and 0.8 mm

thick laminate from inside. All the intermediate shelves shall be 12 mm thick

BWR grade plywood. The shutter shall be of BWR grade blockboards of sliding

types fixed with sliding channels. The vertical divisions of the storages shall be

as per instruction/ drawings. Free edges shall be lipped and polished with

prescribed colour shade of polish. The rates shall include sliding handles, sliding

channels and locks etc.

SFT 40.00

gGeneral chairs with handle for front office, back office, cash area and clients

of Methodex or equivalent make . The upholstery shall be of black rexin.Nos. 9.00

hExecutive High back upholstered chairs for Branch Manager (Methodex Make

or equivalent)Nos. 1.00

i Multi seater for customer waiting area of approved make (3 seater) Nos. 3.00

5 FALSE CEILING :-


Providing , fabricating and erecting lay in type tegular or drop type

ARMSTRONG false ceiling of 600 mm x 600 mm grid with approved brand of

armstrong. The rate shall include the additional cost of Tee and L supports and

other accessories near the ends/ odd size edges/corners. Provide additional

length support from the ceiling to the false ceiling grid wherever necessary,

making necessary openings for electrical light fittings, alarm detectors and any

other fixtures. No extra payment for making openings in the panel/grids for the

purpose of light fittings. Item rate shall include all the taxes, transportation,

erection, loading and unloading and any other incidental expenditure for

completing the work.

SFT 810.00

6 MISCELLANEOUS:-

a

Providing and laying Kota stone platform of 19 mm thick and 2'-0" wide and at

2'-8" high above finished floor level with machine polished edge in the pantry.

The rate shall include the profile cutting and fixing of below counter sink and

polishing the exposed edges of the stone. A 2" kota stone shall be provided

below the moulded edge.

RFt. 4.00

b

Providing of stainless steel sink, faucet and trap fixing in the pantry and

wooden overhead cabinet made out of 19 mm thick BWR grade ply and finished

with 1mm thick laminate of prescribed shade and all open edges finished with

lipping and polished with prescribed polish colour

Ls. 1.00

c

Providing and fixing of vertical blinds (PVC coated polyester Fabric) of

approved shade and colour as per the instruction of the architect tailored to

the size of the window

SFT 100.00

d

Providing and fixing in position frameless double acrylic sheet 2'-6" x 1'-6"

mounted with mirror screws on the walls along with all accessories complete for

display of bank's schemes, posters and notices.

No. 2.00

e

Providing and fixing of pin up notice board made of soft cork board finished

with fabric as approved matching with the colour scheme with a wood moulding

of prescribed shape all around the edges.

Sq.Ft. 25.00

7 12 mm GLASS PARTITION:-

Providing and fixing in position 12mm thk machine polished glass at top of Cash

counter front.Necessary 1 1/2" x1/2" white beech/white ceader moulding with natural

polish to be provided. The work to be completed in all respect as per design ,

direction and approval of Architect.

SFT 25.00

8 SYNTHETIC DOOR MAT :-

Providing and fixing synthetic door mats of approved shade from Birla 3M( 6mm

thk).The work to be completed as per approval of the Architect. NOS 2.00

9 SUGGESTION BOX:-

Providing and fixing suggestion box made out of 19mm block board and finished

with 1.0mm thk laminate & inside to be synthetic enamel painted.A 1" high slit &

small door with key and locking arrangement to be done for dropping & taking out

the slips.The work to be completed as per design,direction & approval of the

architect.

NO 1.00


10 CHEQUE DEPOSIT BOX:-

Providing and fixing cheque deposit box made out of 19mm thk block board &

finished with 1.0mm thk. Laminate & inside to be synthetic enamel painted.a 1" high

slit & small door with key and locking arrangement to be done for dropping & taking

out the slips.The work to be completed as per the design,direction & approval of the

architect.

NO 1.00

11 FIRST AID BOX:-

Providing & fixing in position first aid box made out of 19mm thk. BWR block board

finished with 1.0mm thk. Laminate.Inside to be enamel painted.all exposed edges to

be covered with white beach/white cedar lipping with natural polish.Necessary

hardware like multipurpose lock,brass hinges and handle to be provided.The work to

be completed as per the direction & approval of the architect.

NO 1.00

12 MAIN PANEL ENCASEMENT :-

Providing & Fixing main panel encasement in position fabricated out of 19mm BWP

BB with 1.0mm thk. Laminate for top,both sides&front.Encasement will be having

powder coated alluminium louver & 6mm thk. Glass for seeing the indicator in both

pallahs.The exposed surface of 19mm BWP BB will be finished with white

beach/white ceader lipping & inside to be enamel painted . The item to be completed

in all respect as per design , direction and approval of the Architects.

SFT 35.00

13 STORAGE:- Providing and fixing storage made out of 19mm BWR block board for top,sides&

6mm BWR ply for back finished with 1.0mm laminate . The shutters to be made out

of 19mm block board with 1.0mm laminate. The necessary godrej multipurpose

locks ,6" brass matt finished handles, brass hinges etc to be provided . Inside of the

unit to be synthetic enamel painted in matching tone . All the exposed edeges of the

boards/plywoods to be coverd with white beach/teak wooden lippings/1

1/2"x1"mouldings duly natural polished all complete.For full ht. storage file divider

made out of 6mm thk ply to be provided.The work to be completed as per approval

and specificaion of the Architect.

a) Full ht storage 7'0''(deep 1'-6") SFT 110.00

14 ANTI - STATIC PVC FLOORING:-

Providing and laying 2mm thk. anti - static PVC flooring in UPS/Server and strong

room of approved colour on the existing floor with adhessive. The floor should be

clean,smooth,level,dry and free from oil, The item to be completed in all respects as

per design, direction and approval of the Architect.

SFT 80.00

TOTAL - A

SL. PARTICULAR Qty Unit Rate Amount

A PANEL & DISTRIBUTION BOARDS.

1

Supplying, Fabricating, assembling, inter-connecting, testing and

connecting with incoming and outgoing power cables and lines as

required to comlete the job of CUBICAL TYPE ELECTRICAL

PANEL made from 14 SWG CRC M.S sheet with proper earthing

terminal(Nut-bolt and washer)-02 nos. outside panel, same nut-

bolt to tighten with internal earth bus-bar of panelsituated

inside loose wire box (on top portion of the panel). On top side of

the panel, cable entry arrangement is to be done for incoming

and outgoing of lines. One 6" x 4" enamel type 440 Volts danger

board to be fixed on the main panel busbar cover. All switches

Nos 1

a 100 AMPs MCCB, 35 Kva as main - 1 set

b 100 AMPs 4 Pole Cu. Busbar - 1 set

c 63 AMPs 4pole change over switch - 1 no

d 63 AMPs 4 Pole MCB as DG main - 2 nos

e 40 A D.P MCB (For 5 Kva Ups) - 2 nos

f6-WAY TPN MCB DB with 63 TP & N MCB as main (Power DB)25

A SPMCB-10 Nos.,20 AMPs SP MCB-06 Nos.,16 A SPMCB-02

g 4-WAY TP& N MCB DB with 40 TP& N MCB as main (Lighting

DB)16 AMPs SP MCB-03 Nos., 10 AMPs SP MCB-09 Nos., Neutral

h 32 AMPs DP MCB as glow sign board main - 1 no

iAMPs meter 0-100 AMPs with 3 Nos. CT & selector switch 96 x

96 mm-01 set (A.E make) (CT ratio 100/5) A.E. make - 1 set

jVoltmeter-0-500 Volt A.C. 50 Hertz 96 x96 mm with selector

switch (A.E make)-01 setk 22 mm dia LED indicator Lamp - 6nos

l 02 AMPs sliding fuse - 6 set

m150 x 100 mm enamel danger board 440 Volt(to set on bus bar

cover) - 1 no

2

Supply and fixing of 100 AMPs TPN HRC type SFU at WSEB for

main incoming on MS angle frame and 02 nos. cable end box

including connection complete with wire, lug, pvc tape

Nos 1

3

Supplying, installation and Termination of UPS out-going power

distribution system with 12 way SPN DB comprising of 10A x 10

AMPs SP MCB and 32 AMPs DP RCBO 300 MA as main (MDS

make) IP-42 protection with double door. Power is to be taken

Nos 2

4 Supply, installation and termination of 40 Amp DP MCB in ATM Nos 1

TOTAL FOR PANEL AND DISTRIBUTION BOARD

ELECTRICAL WORKS FOR PRPOPSED BOB - DAKSHIN BARASAT BRANCH

B CABLES AND CABLE END TERMINATION

1Supply & Fixing 3.5 C X 35 Sqmm Al. Ar. Cable From Meter room

to PanelMtr 40

2 Supply & Fixing 3.5 C X 35 Sqmm Al. Ar. Cable From DG to Panel Mtr 30

3Supply & Fixing 3.5 C X 25 Sqmm Al. Ar. Cable From panel to

power DB Mtr 15

4Supply & Fixing 4.0 C X 10Sqmm Al. Ar. Cable From Panal to

Lighting DBMtr 20

5Supply & Fixing 3.0 C X 6 Sqmm Cu. PVC Insulated wire in PVC

Conduit (from panel to UPS) Mtr 40

6Supply & Fixing3.0 C X 6 Sqmm Cu. PVC Insulated wire in PVC

Conduit (from UPS to UPS DB) Mtr 40

7 Supply & Fixing Cable End Termination.

a 3.5 C X 35 Sqmm Al. Ar. Nos 8

b 3.5 C X 25 Sqmm Al. Ar. Nos 4

c 4.0 C X 10 Sqmm Al Ar. Nos 4

d 3.0 C X 6 Sqmm Cu. Nos 8

TOTAL OF CABLE AND CABLE END TERMINATION

C

1

Wiring for Light Point with 20 mm PVC pipe with 2x1.5 Sqmm

wire and 1x1.5 Sqmm green earth wire for light Points as

reqd. complete with modular switch with front plate

a One light controlled by 6A switch Nos 22

b Two light controlled by 6A switch Nos 7

cExhaust fan point with 6 A sw complete with modular switch

plate & M.S conceal box & 3 pin ceiling roseNos 4

dFan point complete with modular switch plate & M.S conceal box

& 3 pin ceiling rose with electric regulator, modular type.Nos 9

eCall bell point with push type switch, modular plate & M.S.

conceal box with buzzer or ding dong type bellNos 2

2

a

Supply, laying of circuit line 2x2.5 sq.mm +1 x 1.5 Sq.mm PVC

insulated copper wire from MCB type lighting DB to 6 amp plug

points (3 nos. 6 Amps plugs to be connected from one circuit line)

Mts 135

bModular type 6 A switch with 6A 5 pin socket . Mounted on

suitable front plateNos 9

WIRING

RAW POINT WIRING-The wiring shall pass through PVC pipe of

20 mm dia with ISI mark to conceal on wall below false ceiling

mending good all the damage

c

Wiring for Power Point 6/16 A Switch & Socket with 25mm PVC

pipe with 2x2.5 Sqmm wire and 1x1.5 Sqmm green earth wire for

Power Points as reqd. This line has to be drawn from the power

DB. (02 nos. plugs to be connected with one circuit)

Mtr 90

dModular type 6/16 A switch. with 16A 5 pin socket . Mounted on

suitable front plate Nos 6

TOTAL OF WIRING

3

a

Wiring for Power Point 6/16 A Switch & Socket with 25mm PVC

pipe with 2x2.5 Sqmm wire and 1x1.5 Sqmm green earth wire

through PVC casing 20 mm dia 16 SWG with ISI mark to lay

from UPS MCB DB to plug point board

Mtr 145

b

Supply and fixing of 2 x 6 Amps 5 pin socket + 1 x 16 amps 6 pin

socket in single board (under table) + 1 x 16 A switch (Modular

switch + socket) in another board above table as per direction

Set 8

c

Do- but 3 x 6/16 , 6 pin socket with three control switch to

provide near HUB Rack and line printer to be connected from

UPS power.

Set 2

d

Supplying, installation of UPS incoming 32 Amps industrial socket

with 32 Amps SPMCB (2 nos. for out going and 2 nos. for

incoming) for 2 Nos UPS

Set 2

TOTAL OF UPS WIRING

D

1

Supplying, laying and connection of telephone points with 2 pair

.51 sq.mm tinned Cu conductor through PVC casing ISI mark

from telephone point to Krone DB complete with RJ 11 telephone

socket modular type in PVC concealed box.

Nos. 6

2Do- 10 pair 0.51 sq.mm copper conductor telephone cable in 20

mm dia PVC pipeMtr. 50

3

Supply, fixing and connection of 10 pair KRONE connector DB

complete with PVC moulded Telephone DB box with locking

system

set 1

TOTAL OF DATA/TELEPHONE-LOW VOLTAGE SYSTEM

F

1Supply and Fixing 580x580 Size 4x 14 Watts TLD Mirror Optic

Light Fittings.( Havells make. )LHCTP8424340Nos. 21

2Supply and Fixing of 1x36/40 Watts 4' length Slim Tube Light

for Coffer Lights (Havells Make)LHIF71104011Nos. 6

DATA/ TELEPHONE-LOW VOLTAGE SYSTEM

UPS WIRING

FIXTURES INCLUDING LAMPS.

3Supply and Fixing of Modular Downlighter of 170mm size with

2x18 watts PL-C/ Model-LHOC33218399 including electronic Nos. 3

49" heavy duty exhaust fan with louvre in toilet / pantry inclusive

of hole cutting in the wall and finished with plastering completeNos. 4

5Wall Hung fan complete with all fitting and mending good all

damagesNos. 7

6Ceiling Hung fan complete with all fitting and mending good all

damagesNos. 2

TOTAL OF FIXTURES

G Providing Change over switch for generator running Job 1

H

1Suppy & fixing of starter with 3 pin plug in recessed MS box

suitable for 1.5TR AC/2 TR ACNos. 4

2Supply and Fixing in 25mm PVC Pipe with 3x 6 Sqmm Cu. Cable

For Single phase A/C Point Complete & reqd.Mtr 120

TOTAL OF A/C SYSTEM

I

aSupplying, laying of main line with 2 x 2.5 sq. mm + 1 x 1.5 sq. mm

through pvc conduit from main panel to glow sign boardMtr 45

bSupplying , fixing of 16 Amps DP MCB at main entrance with Glow

sign board timer (24 hours in original housing)set 1

TOTAL OF GLOW SIGN BOARD

J

1Supply & Fixing 25 mm PVC Pipe with 8 SWG 2no, Copper wire

for Earthing.Mtr. 30

2 Supply & Fixing 25x 3 mm GI Earth Strip 2no,Earthpit to Panal Mtr. 30

3Supply & Fixing 20mm PVC Pipe with 4C x 1.5 Sqmm Cu. Flexible.

Cable for PIR Control ( From Control panal to Each PIR Control LS 1

4Providing and making earthing station complete with 300x300x3

MM Cu Plate Complete with salt coal and watering pipe Complete Nos. 2

TOTAL OF EARTHING

SUMMARY SHEET

TOTAL FOR PANEL AND DISTRIBUTION BOARD

TOTAL OF CABLE AND CABLE END TERMINATION

TOTAL OF WIRING

TOTAL OF UPS WIRING

TOTAL OF DATA/TELEPHONE-LOW VOLTAGE SYSTEM

TOTAL OF FIXTURES

A/C SYSTEM

GLOW SIGN BOARD

EARTHING

Providing Change over switch for generator running

TOTAL OF A/C SYSTEM

TOTAL OF GLOW SIGN BOARD

TOTAL OF EARTHING

TOTAL - B

UCO BANK - HARIDEVPUR BRANCH DEARCH ARCHITECTS (P) LTD.

SL

NO.PARTICULARS AMOUNT

A FURNISHEING WORKS

B ELECTRICAL WORKS

C

GRAND TOTAL

PROPOSED BANK OF BARODA - DAKSHIN BARASAT BRANCH

SUMMARY SHEET

y o u d r e a m i tw e m a k e i t

REVISED FURNITURE LAYOUT OF BOB -DAKSHIN BARASAT BRANCH(Grd. fl.)

NOTES :

1. This drawing is the property of Dearch architects (P) Ltd. & can not be used without their written permission.2. Drawing shall not be scaled written dimensions are to be followed.3. This drawing to be read along with other relevant drawings.4. Any variation between the drawing & the specification should be brought to the notice of the architects in writing prior to the construction.5. For R.C.C. details refer structural engineers drawings.

DRAWING TITLE :

REV. NO. CHK. BY

REVISED FURNITURE LAYOUT OF BOB -DAKSHIN BARASAT BRANCH(Grd. fl.)

DELHI KOLKATA MUMBAI KOCHI BANGALORE CHENNAI HYDERABAD

Any queries in the drawing should be clarified prior to execution.

SCALE : nts REF.: DE ARC / KOL/ BOB/DAKSHIN BARASAT.

after execution. This must not be used by anyone without permission.This is the property of DEARCH ARCHITECTS(P) LTD and should be returned

DRAWN BY : RITABRATA.

REVISED FURNITURE LAYOUT OF BOB - DAKSHIN BARASAT BRANCH

APPD. BY : C.C DATE : 22/03/2012 NO : 1


DEARCH ARCHITECTS PRIVATE LIMITEDC-507 Basement, chittaranjan park,New Delhi-110019Fixed line: +91-11-262 72363,262 72364Tele Fax: +91-11-262 72347E-mail :[email protected]

E W

S

N

CARPET AREA = 990.00 SFT.(excluding toilets)

* Window Sill = 2'-6"(proposed)* Window Height = 4'-6"(proposed)

* True Ceiling Height = 9'-8"

* Beam Drop = 8"

OFFICER

HIS

STOREROOM

UPSROOM

HER

MainEntry

MAIN ROAD

land-lordarea

spaceforATM

land-lordEntry

up

BRANCHMANAGER

SAFEROOM7'

6'-2"4'4'-9"

PANTRY6'-6"

4'4'

3'

CLERK CLERK

7'-6"

10'-4

"

10'-1

0"

6'-9"

7'

5'-7

"

3'-9"

15'

4'-5

"

4'-9"

SW

SW

OPTION - 2

5'

= FULL HEIGHT

= HALF HEIGHT (5'-0")

= CASH (6'-0")


PRO

DU

CED

BY

AN

AU

TOD

ESK

ED

UC

ATI

ON

AL

PRO

DU

CT

PRODUCED BY AN AUTODESK EDUCATIONAL PRODUCTPR

OD

UC

ED B

Y AN

AU

TOD

ESK ED

UC

ATIO

NA

L PRO

DU

CT

PRODUCED BY AN AUTODESK EDUCATIONAL PRODUCT


PROPOSED LIGHTING LAYOUT OF BOB -DAKSHIN BARASAT BRANCH(Grd. fl.)

NOTES :

1. This drawing is the property of Dearch architects (P) Ltd. & can not be used without their written permission.2. Drawing shall not be scaled written dimensions are to be followed.3. This drawing to be read along with other relevant drawings.4. Any variation between the drawing & the specification should be brought to the notice of the architects in writing prior to the construction.5. For R.C.C. details refer structural engineers drawings.

DRAWING TITLE :

REV. NO. CHK. BY

PROPOSED LIGHTING LAYOUT OF BOB -DAKSHIN BARASAT BRANCH(Grd. fl.)

DELHI KOLKATA MUMBAI KOCHI BANGALORE CHENNAI HYDERABAD

Any queries in the drawing should be clarified prior to execution.

SCALE : nts REF.: DE ARC / KOL/ BOB/DAKSHIN BARASAT.

after execution. This must not be used by anyone without permission.This is the property of DEARCH ARCHITECTS(P) LTD and should be returned

DRAWN BY : RITABRATA.

PROPOSED LIGHTING LAYOUT OF BOB - DAKSHIN BARASAT BRANCH

APPD. BY : C.C DATE : 25/05/2012 NO : 1


DEARCH ARCHITECTS PRIVATE LIMITEDC-507 Basement, chittaranjan park,New Delhi-110019Fixed line: +91-11-262 72363,262 72364Tele Fax: +91-11-262 72347E-mail :[email protected]

E W

S

N

CARPET AREA = 00.00 SFT.(excluding toilets)

* Window Sill = 2'-6"(proposed)* Window Height = 4'-6"(proposed)

* True Ceiling Height = 9'-8"

* Beam Drop = 8"

MainEntry

MAIN ROAD

land-lordarea

spaceforATM

land-lordEntry

up

= FULL HEIGHT


= CASH (6'-0")


SB

SB

SB

PRODUCED BY AN AUTODESK EDUCATIONAL PRODUCTPR

OD

UC

ED B

Y A

N A

UTO

DES

K E

DU

CA

TIO

NA

L PR

OD

UC

TPRODUCED BY AN AUTODESK EDUCATIONAL PRODUCT

PRO

DU

CED

BY A

N A

UTO

DESK

EDU

CA

TION

AL PR

OD

UC

T

Bank of Baroda · 32. Alarm bell. 33. G.I. pipe 34. Steel conduits ... BEC / SUPREME / AKG BEC /...

Documents

Transcript of Bank of Baroda · 32. Alarm bell. 33. G.I. pipe 34. Steel conduits ... BEC / SUPREME / AKG BEC /...