AutoSupport QuickStartGuide
-
Upload
marco-espinoza-cordero -
Category
Documents
-
view
213 -
download
0
Transcript of AutoSupport QuickStartGuide
![Page 1: AutoSupport QuickStartGuide](https://reader035.fdocuments.us/reader035/viewer/2022081900/577cce051a28ab9e788d1a15/html5/thumbnails/1.jpg)
AutoSupport Message Transport Guidelines
AutoSupport supports three transport protocols when sending messages to NetApp: HTTPS, HTTP, SMTP.
HTTPS is the default transport protocol used by AutoSupport; you should use it whenever possible.
When you send AutoSupport messages via HTTPS, the X.509 certificate of the NetApp AutoSupport server is validated and the message content is encrypted. When using the HTTP transport protocol, you can disable the validation feature.
Because SMTP can introduce limitations on message and line length, you should use HTTP or preferably, HTTPS for your AutoSupport transport protocol. HTTP uses TCP port 80; HTTPS uses TCP port 443. To use HTTP or HTTPS to send AutoSupport messages, you may need to configure an HTTP or HTTPS proxy. If the network connection does not allow HTTPS or HTTP, you need to configure AutoSupport for SMTP. SMTP uses TCP port 25. Note: if you or your support partner want to receive AutoSupport messages or notifications, SMTP will be the transport protocol used. The transport protocol choice only applies to messages sent to NetApp Global Support. The AutoSupport feature requires an external email server if you use SMTP. The storage systems does not function as an email server – it requires an external email server at your site to send email.
Configuring AutoSupport on the Storage Controller
Step 1: Configure information about your DNS servers.
This is required to resolve Netapp’s AutoSupport HTTP/S destination URLs and if you use host names instead of IP addresses.
Step 2: Configure an email server name or IP address that is able to route email-based messages from the storage controller.
This is required for you or support partners to receive AutoSupport messages, or if you use SMTP as the transport protocol to NetApp.
Step 3: Configure AutoSupport options.
For Cluster-Mode: ::>system node autosupport modify -node node0 –state enable -mail-hosts mailhost.example.com -to [email protected]; -noteto
[email protected] -to partner-address
For 7-Mode: Set AutoSupport options as follows:
>options autosupport.<option>[arguments]
Example: >options autosupport.enable on >options autosupport.mailhost mailhost.example.com >options autosupport.to [email protected]; >options autosupport.noteto [email protected] >options autosupport.partner.to [email protected]
Testing the AutoSupport Configuration
Testing AutoSupport helps ensure that it is properly configured.
For Cluster-Mode:
Data ONTAP 8.1: ::>system mode autosupport invoke -node node0 -type test -message "Test ASUP"
Data ONTAP 8.0:
::>system node autosupport invoke -node node0 -message "Test ASUP"
For 7-Mode:
>options autosupport.doit “Test ASUP”
If the AutoSupport message is sent to NetApp, an email will be sent back to the system owner of record to verify that the message was received.
If you don’t receive the confirmation email from NetApp, perform the troubleshooting task for Blocked Network Ports in the NetApp AutoSupport Family Playbook relative to the transport protocol (HTTP, HTTPS, and SMTP) in use to resolve the problem. Refer to the Data ONTAP System Administration Guide for the version installed.
RESOURCES
http://support.netapp.com
Additional materials, FAQs and presentations are available at: https://fieldportal.netapp.com/viewcontent.asp?html=580 and http://now.netapp.com/NOW/asuphome/
SUBMIT A CASE
NetApp Support > Technical Assistance > Open A Case
CALL A TECHNICAL SUPPORT CENTER
Americas 1.888.4.NETAPP
EMEA 00.800.44.NETAPP
Asia Pacific +800.800.80.800
AutoSupport Configuration Quick Start Guide