Autocad Civil 3d 2009 Subscription Bonus Pack 2 Readme
-
Upload
jlopezlamonega8570 -
Category
Documents
-
view
104 -
download
2
Transcript of Autocad Civil 3d 2009 Subscription Bonus Pack 2 Readme
AutoCAD® Civil 3D® 2009 Subscription Bonus Pack 2 – PDF Enhancements
Thank you for downloading AutoCAD Civil 3D 2009 Subscription Bonus Pack 2 – PDF Enhancements.
This bonus pack is a version of the AutoCAD Subscription Bonus Pack 2 – PDF Enhancements subscription extension that has been specifically created to run on AutoCAD® Civil® 3D or AutoCAD® Civil® 2009. This document includes important information related to the installation and use of this extension. For more information, see the links below.
Contents
Installation Information
Enhanced PDF Output
Attach a PDF File as an Underlay
New and Updated Commands and System Variables
Installation Information
Applicable Products
There are two versions of AutoCAD Civil 3D 2009 Subscription Bonus Pack 2 – PDF Enhancements specific to the following products:
AutoCAD Civil 3D 2009 (Civil3D2009BonusPack2.exe)
AutoCAD Civil 2009 (Civil2009BonusPack2.exe)
These installation programs cannot be installed on AutoCAD or any other AutoCAD-based application.
English Display of New and Updated Functionality
In this bonus pack, new and updated functionality (commands, system variables, options, and warning messages) displays in English only. If you install this bonus pack on a non-English product, all new and updated functionality displays in English.
Install This Bonus Pack
This extension requires that AutoCAD Civil 3D 2009 (or AutoCAD Civil) Update 2.1 be applied to your installation of AutoCAD Civil 3D 2009 (or AutoCAD Civil). This update can be downloaded from the Updates and Service Packs website.
To install the AutoCAD Civil 3D 2009 Subscription Bonus Pack 2 – PDF Enhancements
1. Based on your operating system, download the following self-extracting executable file to any temporary location:
Civil3D2009BonusPack2.exe (for AutoCAD Civil 3D 2009)
Civil2009BonusPack2.exe (for AutoCAD Civil 2009)
2. Double-click and unzip the downloaded file to any specified folder; for example, C:\install\Autodesk\SubscriptionBonusPack2Install.
3. In the AutoCAD Civil 3D 2009 Subscription Bonus Pack 2 Installation wizard, click Next.
4. Follow the instructions on each page of the Installation wizard.
Deploy This Bonus Pack
To deploy AutoCAD Civil 3D 2009 Subscription Bonus Pack 2 – PDF Enhancements
Use a Visual Basic Script (VBScript) to Deploy This Bonus Pack
1. Unzip the self-extracting file Civil3D2009BonusPack2.exe or Civil2009BonusPack2.exe to a network share location; for example, Z:\install\Autodesk\SubscriptionBonusPack2Install.
2. When the zip file extractor appears, deselect when done unzipping open: CDROM1\setup.exe.
NOTE: Save the CDROM1 file in the location specified in the vb script; for example, strSourcePath = "Z:\install\Autodesk\SubscriptionBonusPack2Install\CDROM1".
3. Copy the following text to a file:
' <script_begin> ---------------------------------------- ' Scripted installation for Subscription Bonus Pack 2 option explicit
' define variables dim shell dim productType dim strInstallLevel dim strSourcePath
' Script initialization Set shell = CreateObject("WScript.Shell")
productType = "BonusPack" strInstallLevel=5 ' 5 installs everything, 3 installs typical ' ' Source to install from (e.g. Z:\install\Autodesk\SubscriptionBonusPack2Install\CDROM1)
strSourcePath = "Z:\install\Autodesk\SubscriptionBonusPack2Install\CDROM1" ' RunStandaloneInstall() Wscript.quit()
' Function RunStandaloneInstall shell.run DefaultCommand(),2,1 end function ' Function DefaultCommand dim retString ' /q for silent install ' /c [key] override parameters for the key retString = """" & strSourcePath & "\setup.exe " & """" & " /t /q /c " & productType & ": " retString = retString & "InstallLevel=" & strInstallLevel DefaultCommand = retString end function '
' </script_end>----------------------------------------------------------------
Save the file as a VBS file; for example, InstallExtension.vbs.
Execute the file to deploy this bonus pack.
Uninstall This Bonus Pack
To successfully uninstall both AutoCAD Civil 3D 2009 or AutoCAD Civil 2009 and this bonus pack, you must uninstall this bonus pack first.
Note: When you uninstall this bonus pack, the AutoCAD PDF driver, "DWG to PDF Bonus Pack", is also uninstalled, but the pc3 file is not.
To uninstall AutoCAD 2009 Civil 3D Subscription Bonus Pack 2 – PDF Enhancements
Windows XP
1. On the Windows Start menu, click Settings > Control Panel.
2. In the control panel, click Add or Remove Programs.
3. Find AutoCAD Civil 3D 2009 Subscription Bonus Pack 2 in the list of programs. Click Remove.
4. A "Are you sure you want to uninstall AutoCAD Civil 3D 2009 Subscription Bonus Pack 2 " message displays. Click Yes.
Windows Vista
1. On the Windows Start menu, click Control Panel.
2. Click Programs.
3. Click Programs and Features.
4. Find AutoCAD Civil 3D 2009 Subscription Bonus Pack 2 in the list of programs. Click uninstall.
5. A "Are you sure you want to uninstall AutoCAD Civil 3D 2009 Subscription Bonus Pack 2 " message displays. Click Yes.
Enhanced PDF Output
This bonus pack installs an improved AutoCAD PDF driver, "DWG to PDF Bonus Pack". This driver improves visual quality and decreases the size of PDF files.
Contents
Increased PDF Vector Resolution
Reduced File Size
Embedded Text
Plot Color Merge Control Settings
Preview a Plotted PDF File
Include Layer Information in a PDF File
Increased PDF Vector Resolution
To ensure visual fidelity of PDF files, you must set your vector resolution to 600 dpi. A setting of 600 dpi delivers both precise lineweights and a file size that is not too large.
To change the PDF Vector Resolution default setting
1. At the Command prompt, enter PLOT.
2. In the Plot dialog box, under Printer/Plotter, in the Name drop-down list, select DWG to PDF Bonus Pack.pc3.
3. To the right of the Name drop-down list, click the Properties button.
4. In the Plotter Configuration Editor dialog box, on the Device and Document Settings tab, select the Custom Properties tree node.
5. Under Access Custom Dialog, click the Custom Properties button.
6. In the PDF Properties dialog box, under Resolution, select 600 dpi as the Vector Resolution. NOTE: Increasing the Vector Resolution setting creates a larger PDF file. Decreasing the Vector Resolution setting results in imprecise lineweights.
Reduced File Size
The enhanced DWG to PDF driver reduces the size of the resulting PDF file. Since the AutoCAD PDF driver now embeds fonts as TrueType fonts rather than graphics, the size of a PDF file is reduced. The default Vector Resolution dpi setting has also been modified to maximize visual quality and reduce file size.
Embedded Text
In a PDF file, TrueType fonts are exported as text rather than as graphics. This improves the visual quality of text and also enables highlighting, searching, and copying text within the PDF viewer. When you create a PDF, you can capture some fonts, all fonts, or none. Keep in mind that the more fonts you embed in a PDF file, the larger it becomes. The default behavior of the DWG to PDF driver is to capture fonts you specify (Capture Some), rather than none or all fonts (Capture None or Capture All).
To configure DWG to PDF font handling
1. At the Command prompt, enter PLOT.
2. In the Plot dialog box, under Printer/Plotter, in the Name drop-down list, select DWG to PDF Bonus Pack.pc3.
3. To the right of the Name drop-down list, click the Properties button.
4. In the Plotter Configuration Editor dialog box, on the Device and Document Settings tab, select the Custom Properties tree node.
5. Under Access Custom Dialog, click the Custom Properties button.
6. In the PDF Properties dialog box, under Font Handling, select one of the following options:
Capture None (All Viewer Supplied) Fonts in the source drawing are not included in the PDF file. In order for the fonts used in the source drawing for the PDF file to be visible in the PDF file, the fonts must be present on the PDF viewer’s system. If the fonts used to create the PDF file are not present on the viewer’s system, other fonts are substituted.
Capture Some (Recommended) You select fonts to include in the PDF file from the Available True Type Fonts dialog box. The selected fonts do not need to be available on the PDF viewer’s system in order for them to display in the PDF file. If you select the Capture Some option, click the Edit Font List button. The Available TrueType Fonts dialog box opens. Select fonts you want to include in the PDF file. By default, fonts installed with AutoCAD, Windows, and the PDF file viewer are not selected. If you select Restore Defaults, the list of fonts returns to the default setting. This action is completed and saved before you click OK and it cannot be
undone. The settings in the Available TrueType Fonts dialog box are saved in the registry, not in the current PC3 file. These settings remain in effect for all PDF files until they are changed.
Capture All All fonts in the source drawing are included in the PDF file. This may increase the size of the PDF file. If you select the Capture All option, if desired, click As Geometry. All fonts in the source drawing are included as geometry in the PDF file. To ensure good output quality, plot your drawing at a scale factor of 1:1 or higher.
Plot Color Merge Control Settings
On a raster plotter, you can control the appearance of overlapping lines. The following options are available:
Lines Overwrite: Uses the last plotted line to obscure lines underneath it. Only the uppermost line is visible at the intersection.
Lines Merge: Merges the colors of overlapping lines, creating a third color. For example, merging a magenta line with a yellow line produces red where the lines intersect. Whatever line is received last by the plotter covers intersected lines.
NOTE: Merge control options may display even if a printer does not support this feature. Check your printer's documentation to determine if merge control is supported.
To configure Color Merge control settings
1. At the Command prompt, enter PLOT.
2. In the Plot dialog box, under Printer/Plotter, in the Name drop-down list, select DWG to PDF Bonus Pack.pc3.
3. To the right of the Name drop-down list, click the Properties button.
4. In the Plotter Configuration Editor dialog box, on the Device and Document Settings tab, double-click the Graphics tree node.
5. Click the Merge Control tree node.
6. At the bottom or the Device and Document Settings tab, under Merge control, select Lines Overwrite or Lines Merge.
Preview a Plotted PDF File
A PDF file automatically displays in the PDF viewer after it is plotted. To turn this option on or off, open the PDF Plotter Configuration Editor and then open the Custom Properties dialog box. Select or clear the Open in PDF Viewer When Done check box.
To configure the automatic PDF display option
1. At the Command prompt, enter PLOT.
2. In the Plot dialog box, under Printer/Plotter, in the Name drop-down list, select DWG to PDF Bonus Pack.pc3.
3. To the right of the Name drop-down list, click the Properties button.
4. In the Plotter Configuration Editor dialog box, on the Device and Document Settings tab, select the Custom Properties tree node.
5. Under Access Custom Dialog, click the Custom Properties button.
6. In the Additional Output Settings area, select the Open in PDF Viewer When Done check box.
Include Layer Information in a PDF File
When you plot a PDF file, you can display layer information. When you include layer information in the PDF, layers that are turned on and thawed in the DWG are available in the PDF file. If you do not include layer information, only the geometry in the DWG's visible layers appear in the PDF and you cannot manipulate the layers.
To include layer information in a PDF file
1. At the Command prompt, enter PLOT.
2. In the Plot dialog box, under Printer/Plotter, in the Name drop-down list, select DWG to PDF Bonus Pack.pc3.
3. To the right of the Name drop-down list, click the Properties button.
4. In the Plotter Configuration Editor dialog box, on the Device and Document Settings tab, select the Custom Properties tree node.
5. Under Access Custom Dialog, click the Custom Properties button.
6. In the Additional Output Settings area, select the Include Layer Information check box.
Attach a PDF File as an Underlay
Contents
Overview of Attaching a File as a PDF Underlay
Work with a PDF Underlay
Manage and Publish a Drawing Containing a PDF Underlay
Overview of Attaching a File as a PDF Underlay
Contents
Attach a PDF Underlay
Detach a PDF Underlay
Unload or Reload a PDF Underlay
Snap to a geometric point on a PDF underlay
Attach a PDF Underlay
You can attach a PDF file as an underlay to a drawing file. An underlay file is referenced and placed in a drawing file the same way that raster image files are; it is not actually part of the drawing file. Like a raster file, an underlay is linked to the drawing file through a path name. The path to the file can be changed or removed at any time. By attaching an underlay this way, you can use a file in your drawing without greatly increasing the file size of the drawing.
NOTES:
Although an underlay file is a reproduction of its source drawing, it is not as precise as a drawing file. An underlay may show slight discrepancies in precision.
You can only view a PDF Underlay in the 2D Wireframe visual style.
If you open a DWG with a PDF underlay in a version of AutoCAD earlier than this bonus pack, the file will open, but the PDF underlay will not display.
TIP: When you create a PDF file, to ensure visual fidelity, embed fonts.
Attaching an Underlay Multiple Times
You can reattach an underlay multiple times, treating it as a block. Each underlay has its own clip boundary and settings for contrast, fade, and monochrome. However, you cannot bind an underlay to a drawing and you cannot edit or modify the underlay’s drawing content.
Layers in Underlay Files
If an underlay file contains more than one layer, you can control how the layers display after attaching the file. If a file does not contain layer information, the PDF Layers dialog box does not display layer information.
Underlay Files in XRefs
If you work with a drawing that has DWG file references (xrefs), be aware that one of the DWG references may include an underlay. In this situation, objects in the underlay are visible in the parent DWG file.
For example, drawing A includes a PDF underlay showing some mechanical details. You need the content of drawing A attached to your current drawing, drawing B. If you attach drawing A as an external reference to drawing B, the PDF underlay that was already attached to drawing A is also present.
All of the property settings made to the underlay in the DWG file reference, such as clipping boundaries, display as they do in the parent drawing.
Password Protected Underlay Files
If a file you want to attach as an underlay is password protected, you are prompted to enter the password. You cannot attach the file until you have correctly entered the password.
After an underlay is attached to a DWG file, you are prompted for the PDF file’s password each time you open the DWG file. If the DWG file is also password protected, or has several other protected drawing references attached, you may be prompted for multiple passwords.
If you choose to redirect the path of an underlay to a file that requires a password, you are prompted for a password.
TIP: PDF file passwords are case sensitive, but DWG file passwords are not. To make synchronization between PDF and DWG file passwords easier, make sure the PDF file password matches the DWG file password and is entirely uppercase.
To attach a PDF underlay
1. At the Command prompt, enter PDFATTACH.
2. In the Select PDF File dialog box, select the file you want to attach.
3. In the Attach PDF Underlay dialog box, use one of the following methods to specify the insertion point, scale, or rotation of the underlay file:
Select Specify On-Screen to use the pointing device to attach the PDF underlay at the location, scale, or angle you want.
Clear Specify On-Screen and enter values under Insertion Point, Scale, or Rotation.
4. Click OK.
Command entry: PDFATTACH
Detach a PDF Underlay
You can detach PDF underlays that are no longer needed in a drawing. When you detach an underlay, all instances of the underlay are removed from the drawing, the underlay definition is purged, and the linking path to the file is removed.
To hide the display of an underlay temporarily, you can unload it rather than detach it. This action preserves the PDF underlay and its location for reloading later.
NOTE: Erasing an individual instance of an underlay is not the same as detaching it. An underlay must be detached to remove the link from your drawing to the file.
To detach a PDF underlay
1. At the Command prompt, enter EXTERNALREFERENCES..
2. In the External References palette, in the File References pane, select the PDF underlay you want to detach.
3. Right-click on the PDF underlay and click Detach.
The PDF underlay is no longer linked to the drawing file. All instances of the underlay are removed from the drawing.
Unload or Reload a PDF Underlay
You can improve performance by unloading PDF underlays when you do not need them in the current drawing session. Unloaded underlays are not displayed or plotted. Unloading an underlay does not alter its link. If you do not have sufficient memory to open multiple attached underlays in a drawing, underlays are automatically unloaded.
In the External References palette, you can use Reload to reload an unloaded underlay or to update a loaded underlay by reloading the underlay from the specified directory path. If a drawing is closed after an underlay is unloaded, the underlay file is not loaded when the drawing is next opened; you must reload it.
To unload or reload a PDF underlay
1. Open the External References palette.
2. In the File References pane, select a PDF underlay.
3. Right-click, and click Unload or Reload. When unloaded, the PDF underlay is still linked to the drawing file, but it is not displayed in the drawing.
To Snap to a Geometric Point on a PDF Underlay
To snap to a geometric point on a PDF underlay
1. At the prompt for a point, hold down SHIFT and right-click in the drawing area. Select the object snap you want to use.
2. Move your cursor over the desired object snap location. If AutoSnap is on, your cursor automatically locks onto the snap location you selected, and a marker and tooltip indicate the object snap point.
3. Select an object. The cursor snaps to the eligible location closest to your selection.
Work with a PDF Underlay
Contents
Control the Display of Layers in a PDF Underlay
Modify the Position, Scale, or Rotation of a PDF Underlay
Adjust the Contrast, Fade, Monochrome, and Background Color of a PDF Underlay
Clip a PDF Underlay
Hide and Show a PDF Underlay Frame
Control the Display of Layers in a PDF Underlay
By default, all visible layers of a PDF file are turned on when you attach the file as an underlay. It is usually convenient to turn off any unneeded layers to reduce the visual complexity of your work. Use the PDFLAYERS command.
NOTE: If a PDF underlay does not contain layers, an empty PDF Layers dialog box is displayed.
You can use the Properties palette to determine whether the layer state of a PDF underlay has been modified.
If no layers are turned off, the Layer Display Override property is set to None.
If at least one layer is turned off, the Layer Display Override property is set to Applied.
To turn layers on and off in a PDF underlay
1. Select an underlay by clicking its bounding frame.
2. At the Command prompt, enter PDFLAYERS.
3. In the PDF Layers dialog box, click the lightbulb icon for the layer name that you want to turn on or off. You can use CTRL or SHIFT when you click to select several layers.
4. Click Apply to save your changes, or click OK to save and close.
Command entry: PDFLAYERS
Modify the Position, Scale, or Rotation of a PDF Underlay
While you can specify the insertion point, scale factor, and rotation angle at the time you attach a PDF file, you may want to alter those settings as your drawing progresses. By default, the insertion point of a file is 0,0,0, its scale factor is 1, and its rotation angle is 0.
Since PDF underlay behavior is similar to attached raster image behavior, you can use general modify commands such as move, scale, rotate, mirror, and array. After you select a PDF underlay, you can alter it by choosing commands from the Properties palette.
TIP: Double-clicking an underlay opens the Properties palette for that underlay.
Use Object Snaps
Use object snaps if you need to draw or edit objects relative to the objects displayed by one or more attached underlays. Object snapping to underlay geometry is the same as
object snapping to geometry in DWG files. Object snapping for underlays is turned on and off with the PDFOSNAP system variable.
Use Grips with Underlays
While PDF underlay behavior generally follows the pattern set by raster images, one exception is the way grips work. In this case, the behavior more closely parallels block behavior. Normally, a PDF underlay displays only a base grip. You can use a base grip to reposition a PDF underlay in a drawing. If you create a clipping boundary, additional grips display for each corner of the boundary.
The grip for the base point is the lower-left corner of the PDF underlay.
To use the Properties palette to edit the position, scale, or rotation of a PDF underlay
1. In the drawing viewport, double-click the underlay that you want to edit.
2. In the Properties palette, display the Geometry area and do one of the following:
To change the underlay position, change the settings for Position X, Y, or Z.
To change the underlay scale, width, or height, change the settings for Scale, Width, and Height.
To change the underlay rotation, change the setting for Rotation.
To use a base grip to edit the position of a PDF underlay
1. Click the frame of an attached PDF underlay.
2. To reposition the PDF underlay, click the base grip.
3. Drag the cursor to the new location and then click again to place the PDF underlay.
Adjust Underlay Contrast, Fade, Monochrome, and Background Color of a PDF Underlay
Aside from using the Properties palette to edit the position, scale, and rotation of a PDF underlay, you can also modify the contrast, fade and monochrome values, and colors for the background of a PDF underlay. Adjusting these settings does not alter the original file and does not affect other instances of the PDF underlay in the drawing.
You can make changes to contrast, fade and monochrome values, and colors for the background of a PDF underlay from the Properties palette, under the PDF Adjust section. You can also use the PDFADJUST command to make these changes.
If you change contrast and fade and monochrome values, plotted output is affected.
Contrast
Contrast controls the appearance of the dimmest linework that is present in a PDF underlay and works in conjunction with the Fade setting. When Contrast is set to 100, all the linework matches the intensity of the Fade value. When Contrast is set to 20, the dimmest lines are attenuated by 20 percent of the Fade value.
Fade
Fade controls how light or dark the linework is displayed. Higher values produce lighter linework; conversely, lower fade values produce darker linework.
Monochrome
Monochrome controls the color saturation of all linework while maintaining the luminance. When turned on, the linework appears in varying shades of gray starting at black if the background color luminance is 50 percent or more. If the background color luminance is less than 50 percent, then the colors are inverted, with the darkest linework displaying in white, and the lightest linework displaying in black. This inversion is used to show the underlay on the screen, but is reverted again for plotting.
Adjust Colors for Background
Adjust Colors for Background controls whether the underlay colors are visible against the drawing background color. The default setting of Yes indicates that the background colors of the PDF underlay and the drawing environment are analyzed to see if they are both light or both dark, or is one dark and the other light. When one background is light and the other dark, the colors of the underlay are inverted so the underlay is displayed. If the setting is changed to No, the original colors of the underlay are used. Depending on the background colors, the underlay might not be visible.
NOTE: For the best color fidelity, change the background color of your drawing to white. Since most PDF files have a transparent background, the color fidelity of a PDF object may be altered by a non-white background.
To use the Properties palette to adjust the contrast, fade, monochrome, and background color of a PDF underlay
1. Select the PDF underlay to adjust.
2. Click Modify menu > Properties.
3. In the Properties palette, display the Geometry area and do one of the following:
Adjust the contrast by entering a new value. The default value for contrast is 100 on a scale from 0 (low) to 100 (high).
Adjust the fade by entering a new value. The default value for fade is 0 on a scale from 0 (darker) to 80 (lighter).
Turn Monochrome On or Off. The default setting for monochrome is Off.
Set Adjust Colors for Background to Yes or No. The default setting for Adjust Colors for Background is Yes.
The appearance of the underlay is updated in real-time as you make adjustments in the Properties palette.
To use the PDFADJUST command to adjust the fade, contrast, and monochrome settings of a PDF underlay
1. At the Command prompt, enter PDFADJUST.
2. Select a PDF underlay.
3. At the prompt, enter f (Fade), c (Contrast), or m (Monochrome).
4. Enter a value for the setting you selected in Step 3.
5. Press ENTER. The appearance of the PDF underlay is updated after you enter the new value and the command is completed.
Clip a PDF Underlay
You can define part of an underlay that you want to display and plot by setting up a clipping boundary. An added advantage of setting a clipping boundary is an increase in redrawing speed. The clipping boundary can be a rectangle or a two-dimensional (2D) polygon with vertices within the overall extents of the underlay. Each instance of an underlay can only have one clipped boundary. Multiple instances of the same underlay can have different boundaries. You can change the boundary of a clipped underlay at any time.
You can display a clipped underlay using the clipping boundary, or you can hide the clipping boundary to display the underlay with its original boundaries.
When the clipping boundary is no longer needed, you can delete the clipped boundary from the underlay. When you delete a clipping boundary, the underlay is displayed with its original boundary.
To clip a PDF underlay
1. Select an underlay by clicking it bounding box.
2. At the Command prompt, enter PDFCLIP.
3. At the Command prompt, enter n (New Boundary).
4. Enter p (Polygonal) or r (Rectangular), and then draw the boundary on the PDF underlay. If you are drawing a polygonal boundary, you are prompted to specify consecutive vertices. To finish drawing a polygon, press ENTER.
Ribbon: Subscription tab > PDF Reference panel > PDF Clip
Command entry: PDFCLIP
To specify a new boundary on a clipped PDF underlay
1. Select a clipped PDF underlay.
2. At the Command prompt, enter PDFCLIP.
3. At the Command prompt, enter n (New Boundary).
4. Enter y (Yes) to delete the old boundary.
5. Enter p (Polygonal) or r (Rectangular), and then draw the new boundary on the underlay. If you are drawing a polygonal boundary, you are prompted to specify consecutive vertices. To finish drawing a polygon, press ENTER. You can modify clipped boundaries with grips.
Ribbon: Subscription tab > PDF Reference panel > PDF Clip
Command entry: PDFCLIP
To edit the existing boundary on a clipped PDF underlay
1. Select a clipped PDF underlay.
2. Click one of the grips and drag it to a new location.
Command entry: PDFCLIP
To show or hide the clipped portion of a PDF underlay
1. Right-click a PDF underlay and select Properties.
2. In the Misc group of the Properties palette, set Show clipped to No.
Command entry: PROPERTIES
To delete the boundary of a clipped PDF underlay
1. Select the clipped PDF underlay.
2. At the Command prompt, enter PDFCLIP.
3. Enter d (Delete) and press ENTER. The boundary of the clipped PDF underlay is deleted, and the original boundary of the PDF underlay is restored.
Command entry: PDFCLIP
Hide and Show a PDF Underlay Frame
A frame is a visual border that shows the extents of the PDF underlay, or the clipped boundary of the PDF underlay. Hiding the PDF underlay frame prevents it from being plotted or displayed. You can, however, select the PDF underlay with the pointing
device when the frame is not visible. You can select a PDF underlay if it is not on a locked layer; for example, if the PDF underlay is part of a named selection set made with the All option when selecting objects. When a PDF underlay frame is hidden, a clipped PDF underlay is still displayed to its specified boundary limits; only the boundary is affected. Showing and hiding a PDF underlay frame affects all PDF underlays attached to a drawing.
To hide and show a PDF underlay frame
1. At the Command prompt, enter PDFFRAME.
2. At the Command prompt, do one of the following:
To hide PDF underlay frames, enter 0.
To show and plot PDF underlay frames, enter 1.
To show PDF underlay frames but not plot them, enter 2.
Command entry: PDFFRAME
Manage and Publish Drawings Containing a PDF Underlay
Contents
Display Information for a PDF Underlay
Change the File Path of a PDF Underlay
Publish, Save, and eTransmit a Drawing Containing a PDF Underlay
Reference Manager and PDF Underlays
Display Information for a PDF Underlay
In the External References palette, you can view PDF underlay information either as a list or as a tree. To control how the information is displayed in the External References palette, click the List View or Tree View button in the upper-right corner. The list view displays the name of each PDF underlay in the drawing, its loading status, file size, date last modified, and search path. The tree view lists PDF underlays in a hierarchy that shows their nesting level within xrefs and blocks. The status, size, and other information do not display in the tree view.
In both views, you can do the following:
Display information about an underlay
Attach or detach an underlay
Unload or reload an underlay
Browse for and save a new search path
Use the List View
The list view displays all PDF underlays attached to the current drawing, but it does not specify the number of instances. It is the default view. To sort PDF underlays by category, click the column heading. To change the width of a column, drag its border to the right or left.
The following information is displayed in the list view:
Name of PDF file
Status (loaded, unloaded, or not found)
File size
File type
Date and time file was last saved
Name of the saved path
If the program cannot find a PDF underlay, its status is listed as Not Found. If a PDF underlay is not loaded, its status is Unloaded. A PDF Underlay with a status of Unloaded or Not Found does not display in a drawing.
Use the Tree View
The top level of the tree view lists PDF underlay files in alphabetical order. In most cases a PDF underlay file is linked directly to the drawing and listed at the top level. However, if an xref or a block contains an attached PDF underlay, additional levels display.
You can preview a selected underlay and view PDF file details, including
Reference name
Status
File size
File type
File creation date
Saved path
Found At path (where the PDF is found) NOTE: The Found At path is disabled if a nested reference is selected.
To display a list of PDF underlays attached to a drawing
1. At the Command prompt, enter EXTERNALREFERENCES.
2. In the External References palette, click the List View button.
Command entry: EXTERNALREFERENCES
To display PDF underlay names and their nesting levels within xrefs and blocks
1. At the Command prompt, enter EXTERNALREFERENCES.
2. In the External References palette, click the Tree View button.
Command entry: EXTERNALREFERENCES
To display the status of a PDF underlay layer override
1. Select a PDF underlay for which you want to view the layer override status.
2. Right-click the underlay and select Properties.
3. In the Properties palette, scroll to Misc and view the status of the layer displayed in the Layer Display Override option.
Command entry: PROPERTIES
Change File Paths of a PDF Underlay
When you open a drawing with an attached PDF file, the path of the selected PDF underlay displays in the External References palette under Found At in the Detail list. The displayed path is the actual path where the source file was found. The path where the source file was originally attached displays under Saved Path.
To locate a PDF file, the program searches the following paths and folders in the following order:
Path specified when the underlay was attached
Folder containing the current drawing file
Project search paths specified on the Files tab of the Options dialog box
Support search paths specified on the Files tab of the Options dialog box
Start In folder specified in the program shortcut
If you open a drawing that contains a PDF underlay that is not in the saved path location or in any of the defined search paths, the External References palette displays Not Found in the Status column of the File References list, and the Found At entry is blank in the Details list.
You can remove the path from the file name or specify a relative path by manually editing the path in the Found At box or by clicking [...] at the right side of the Found At box. This opens a Select File dialog box.
To change a PDF underlay path
1. At the Command prompt, enter EXTERNALREFERENCES.
2. In the External References palette, select a PDF underlay whose path you want to change. Click the [...] at the right side of the Found At box.
3. In the Select PDF File dialog box, select a new path. Click Open. The new path is displayed in the Saved Path column.
Command entry: EXTERNALREFERENCES
Publish, Save, and eTransmit a Drawing Containing a PDF Underlay
When you eTransmit a file, PDF underlays are tracked and managed. Furthermore, PDF underlays are not lost when you save to previous drawing formats.
Plot and Publish
When a drawing file containing an underlay is plotted or published to a new file, any visible geometry is included in the newly plotted or published file. However, none of the layer data from the original PDF attachment gets published with the new file.
Save to a Previous DWG Format
If you save the drawing to a previous DWG format, the underlay does not display when the drawing is opened in an older version of the program, nor does it display as a proxy object or a proxy frame. The underlay displays again when you reopen the drawing in the current version of the program.
eTransmit
PDF attachments are tracked and managed when you use eTransmit in the same way raster image attachments are tracked and managed.
Reference Manager and PDF Underlays
With the Reference Manager, you can view underlays that are attached to a DWG file and edit the paths of the attachments. The properties reported by the Reference Manager include
File type
Status
File name
Reference name
Saved path
Found path
Host drawing
Host version
You can view the list of references by drawing or by reference type.
To check a PDF underlay with the Reference Manager
1. Click Start menu (Windows) > All Programs (Programs) > Autodesk > AutoCAD Civil 3D 2009 > Reference Manager.
2. In the Reference Manager, click the Add Drawings button.
3. In the Add Drawings dialog box, select a drawing and then click Open.
New and Updated Commands and System Variables
The following commands and system variable have been added or updated for AutoCAD Civil 3D 2009 Subscription Bonus Pack 2:
Commands
PDFADJUST
-PDFADJUST
PDFATTACH
-PDFATTACH
PDFCLIP
PDFLAYERS
System Variables
PDFFRAME
PDFOSNAP
PDFADJUST Command
Adjusts the display of a PDF underlay or plotted drawing from the Command prompt.
Access Methods
Command entry: PDFADJUST
Select PDF underlay: Select one or more PDF underlays
Enter PDF underlay option [Fade/Contrast/Monochrome]:
Summary
Adjusts the Fade, Contrast and Monochrome settings for a selected underlay. If you selected a single PDF underlay, the default values for Fade, Contrast, and Monochrome are the current property settings of the selected underlay. If you select multiple underlays, the default values for Fade, Contrast, and Monochrome remain as they were set the last time the command was used.
Fade
Controls the fade effect of the underlay. Values range from 0 through 100. The greater the value, the lighter the linework in the underlay appears. Works indirectly with the contrast effect; a higher contrast value blends the underlay into the background when fade is set to a higher value. Default=0.
Enter fade value (0-80): Enter a value
Contrast
Controls the contrast, and indirectly, the fading effect of the underlay. Values range from 0 through 100. The greater the value, the more each pixel is forced to its primary or secondary color. Default=100.
Enter contrast value (0-100): Enter a value
Monochrome
Controls the color saturation of all linework while maintaining the luminance. When turned on, the linework displays in varying shades of gray starting at black if the background color luminance is 50 percent or more. If the background color luminance is less than 50 percent, then the colors are inverted, with the darkest linework displaying in white, and the lightest linework displaying in black.
Monochrome? [Yes/No]: Select yes or no and then press ENTER
-PDFADJUST Command
Adjusts the Fade, Contrast, and Monochrome settings for a selected underlay from the command line.
Access Methods
Command entry: -PDFADJUST
Summary
If you enter -PDFADJUST at the Command prompt, the following PDFADJUST command prompts are displayed.
Select PDF Underlay: Select an underlay
Enter PDF underlay option [Fade/Contrast/Monochrome]: Select Fade, Contrast, or Monochrome
Enter fade value [0-100] <0>: Enter a fade value
Enter contrast value [0-100] <75>: Enter a contrast value
Enter monochrome value [Yes/No] <No>: Enter yes or no
PDFATTACH Command
Access Methods
Ribbon: Subscription tab > PDF Reference panel > Attach PDF
Command entry: PDFATTACH
Summary
When you attach a PDF file as an underlay, you link that referenced file to the current drawing. Any changes to the referenced file are displayed in the current drawing when it is opened or reloaded.
The Select PDF File dialog box (a standard file selection dialog box) is displayed. Once you select a PDF file, the Attach PDF Underlay dialog box is displayed.
NOTE: If you plan to access PDF files from the Vault client server, the Vault file open dialog box supersedes the Select PDF File dialog box.
Attach PDF Underlay Dialog Box
Names, locates, and defines the insertion point, scale, and rotation of attached PDF underlays.
Access Methods
Ribbon: Subscription tab > PDF Reference panel > Attach PDF
Command entry: PDFATTACH
Name
Identifies the PDF file you have selected to attach, either from the Select PDF File dialog box (an unattached PDF file) or from the list of previously attached PDF underlays. To add another instance of a PDF underlay that is already attached, select the PDF name from the list.
NOTE: The Name field is disabled when you attach a PDF file that is stored on the Vault client server. This information is automatically entered by the Vault.
Browse Open the Select PDF File dialog box (a standard file selection dialog box). NOTE: The Browse button is hidden when you are attaching a PDF file that is stored on the Vault client server.
Found In Displays the path where the PDF file is located.
Saved Path Displays the path that is saved with the drawing when the PDF file is attached. The path is dependent upon the Path Type setting.
Select a Page
Displays all of the pages that are found in a PDF file. By default, the first page is selected.
Path Type
Specifies one of three types of folder path information to save with an attached PDF underlay: a full path, a relative path, and no path.
NOTE: The Path Type group is disabled when you’re attaching a PDF file that is stored on the Vault client server. This information is automatically entered by the Vault.
Full Path Specifies the full (absolute) path to the PDF file.
Relative Path Specifies a relative path to the PDF file.
No Path Specifies only the PDF file name. The PDF file should be located in the folder with the current drawing file.
Insertion Point
Specifies the insertion point for the selected PDF file. Specify On-Screen is the default. The default insertion point is 0,0,0.
Specify On-Screen Directs input at the Command prompt or the pointing device. If Specify On-Screen is clear, enter the insertion point in X, Y, and Z.
X Sets the X coordinate value.
Y Sets the Y coordinate value.
Z Sets the Z coordinate value.
Scale
Specifies the scale factor of the selected PDF underlay.
Specify On-Screen directs input at the Command prompt or the pointing device. If Specify On-Screen is clear, enter a value for the scale factor. The default scale factor is 1.
If INSUNITS is set to unitless or if the underlay does not contain resolution information, the scale factor becomes the underlay width in AutoCAD units. If INSUNITS has a value such as millimeters, centimeters, inches, or feet, and the underlay has resolution information, the scale factor is applied after the true width of the underlay in AutoCAD units is determined.
Rotation
Specifies the insertion point for the selected PDF file. Specify On-Screen is the default. The default insertion point is 0,0,0.
Specifies the rotation angle of the selected PDF underlay.
If Specify On-Screen is selected, you may wait until you exit the dialog box to rotate the object with your pointing device or enter a rotation angle value at the Command prompt. If Specify On-Screen is clear, enter the rotation angle value in the dialog box. The default rotation angle is 0.
-PDFATTACH Command
Summary
If you enter -PDFATTACH at the Command prompt, the following PDFATTACH command prompts are displayed.
Path to PDF file to attach: Enter the path and file name of the PDF file to be attached
Enter page number or [?] <1>: Specify a number or ?
If you enter ?, the following prompts display:
Enter pages to list <*>: Enter a page number or press ENTER to list all pages
After the sheets are listed, the previous prompt returns.
PDFCLIP Command
Access Methods
Ribbon: Subscription tab > PDF Reference panel > PDF Clip
Command entry: PDFCLIP
Summary
Clips the display of a selected PDF underlay to a specified polygonal or rectangular boundary. The clipping boundary determines the portion of the PDF outside the boundary that is hidden. The visibility of the clipping boundary is controlled by the PDFCLIP command. To turn the clipping boundary frame on or off, use the PDFFRAME system variable.
Enter PDF clipping option [ON/OFF/Delete/New Boundary] <New Boundary>: Select an option and press ENTER
On
Turns on clipping and displays the PDF underlay clipped to the previously defined boundary.
Off
Turns off clipping and displays the entire PDF underlay.
If you reclip the PDF underlay while clipping is turned off, clipping is automatically turned back on. You are prompted to delete the old boundary even when clipping is turned off and the clipping boundary is not visible.
Delete
Removes a predefined clipping boundary and redisplays the full original underlay.
New Boundary
Specifies a new clipping boundary. The boundary can be rectangular or polygonal, and consists only of straight line segments. When defining a clipping boundary, specify vertices within the PDF underlay boundary. Rectangular is the default option. If you use the pointing device to specify a point at the Enter Clipping Type prompt, the point is interpreted as the first corner of a rectangle.
Enter PDF clipping option [ON/OFF/Delete/New Boundary] <New Boundary>: Select an option and press ENTER
The visibility of the clipping boundary is controlled by the PDFCLIP command.
Enter clipping type [Polygonal/Rectangular] <Rectangular>:
Polygonal
Uses specified points to define a polygonal boundary.
Specify first point: Specify a point
Specify next point or [Undo]: Specify a point or enter u
Specify next point or [Undo]: Specify a point or enter u
Specify next point or [Close/Undo]: Specify a point, or enter c or u
You must specify at least three points to define a polygon.
If the PDF underlay already has a clipping boundary defined, the following prompt is displayed:
Delete old boundary? [No/Yes]
<Yes>: Enter n or press ENTER
If you enter Yes, the entire PDF underlay is redrawn and the command continues; if you enter No, the command ends.
Rectangular Specifies a rectangular boundary by its opposite corners. The rectangle is always drawn parallel to the edges of the PDF underlay.
Specify first corner point: Specify a point
Specify opposite corner point: Specify a point
PDFLAYERS Command
Controls the display of layers in PDF underlay.
Access Methods
Command entry: PDFLAYERS
Summary
Launches the PDF Layers dialog box where you can turn layers on and off.
PDFFRAME System Variable
Type: Integer Saved in: Registry Initial value: 1
Determines whether the PDF underlay frame is visible.
0 The PDF underlay frame is not visible and it is not plotted
1 Displays the PDF underlay frame and allows it to be plotted
2 Displays the PDF underlay frame, but keeps it from being plotted
PDFOSNAP System Variable
Type: Integer Saved in: Registry Initial value: 1
Determines whether object snapping is active for geometry in PDF underlays that are attached to the drawing.
If you cannot snap to your drawing, it may contain a PDF underlay that is a raster image. Object snaps only work with vector-based geometry, not scanned images.
In some PDF underlays, depending on how they were created, some snap modes may not function correctly. For example, you may not be able to snap to the center of arcs or circles in a PDF underlay. To ensure that object snaps function correctly in PDF underlays, use the DWG to PDF Bonus Pack.pc3 plotter driver to create PDF files.
0 Object snapping is disabled for geometry in all PDF underlay attachments in the drawing
1 Object snapping is enabled for geometry in all PDF underlay attachments in the drawing