AUDIO VIDEO SURROUND RECEIVER KRF-V6050D …manual.kenwood.com/files/B60-4947-00.pdf ·...
Transcript of AUDIO VIDEO SURROUND RECEIVER KRF-V6050D …manual.kenwood.com/files/B60-4947-00.pdf ·...
Oper
atio
nsPr
epar
atio
nsAd
ditio
nal I
nfor
mat
ion
Rem
ote
Cont
rol
AUDIO VIDEO SURROUND RECEIVER
KRF-V6050DKRF-V5050DINSTRUCTION MANUALKENWOOD CORPORATION
B60-4947-00 01 MA (E2, T) 0009PR
About the supplied remote controlCompared to standard remote controls, the remote control supplied with this receiver has several operationmodes. These modes enable the remote control to control other audio/video components. In order toeffectively use the remote control it is important to read the operating instructions and obtain a properunderstanding of the remote control and how to switch its operation modes (etc.).Using the remote control without completely understanding its design and how to switch the operation modesmay result in incorrect operations.
This instruction manual is used to describe multiple models listed above.
Model availability and features (functions) may differ depending on the country and
sales area.
*_4947/01-07/EN 3/15/01, 9:52 AM1
2
Preparations
WARNING :TO PREVENT FIRE OR ELECTRIC SHOCK, DO NOTEXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOTREMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS IN-SIDE, REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
THE LIGHTNING FLASH WITH ARROWHEAD SYMBOL,WITHIN AN EQUILATERAL TRIANGLE, IS INTENDED TOALERT THE USER TO THE PRESENCE OF UNINSULATED“DANGEROUS VOLTAGE” WITHIN THE PRODUCT’S EN-CLOSURE THAT MAY BE OF SUFFICIENT MAGNITUDE TOCONSTITUTE A RISK OF ELECTRIC SHOCK TO PERSONS.
CAUTIONRISK OF ELECTRIC SHOCK
DO NOT OPEN
Unpack the unit carefully and make sure that all accessories are put asideso they will not be lost.Examine the unit for any possibility of shipping damage. If your unit isdamaged or fails to operate, notify your dealer immediately. If your unitwas shipped to you directly, notify the shipping company without delay.Only the consignee (the person or company receiving the unit) can file aclaim against the carrier for shipping damage.We recommend that you retain the original carton and packing materialsfor use should you transport or ship the unit in the future.
Keep this manual handy for future reference.
Before applying the power Caution : Read this page carefully to ensure safeoperation.
Safety precautions
Unpacking
Accessories
FM indoor antenna (1) AM loop antenna (1)
THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRI-ANGLE IS INTENDED TO ALERT THE USER TO THE PRES-ENCE OF IMPORTANT OPERATING AND MAINTENANCE(SERVICING) INSTRUCTIONS IN THE LITERATURE ACCOM-PANYING THE APPLIANCE.
For KRF-V6050D
Batteries (R6/AA) (2)Remote control unit (1)RC-R0616
Units are designed for operation as follows.
U.S.A and Canada ............................................ AC 120 V onlyAustralia ........................................................... AC 240 V onlyEurope and U.K. ............................................... AC 230 V onlyChina and Russia ............................................ AC 220 V onlyOther countries ............................... AC 110-120 / 220 - 240 V
Remote control unit (1)RC-R0512
For KRF-V5050D
Batteries (R6/AA) (2)
Factory fitted moulded mains plug
1.The mains plug contains a fuse. For replacement, use only a 13-Amp ASTA-approved (BS1362) fuse.
2.The fuse cover must be refitted when replacing the fuse in themoulded plug.
3.Do not cut off the mains plug from this equipment. If the plugfitted is not suitable for the power points in your home or the cableis too short to reach a power point, then obtain an appropriatesafety approved extension lead or adaptor, or consult your dealer.If nonetheless the mains plug is cut off, remove the fuse and dis-pose of the plug immediately, to avoid a possible shock hazard byinadvertent connection to the mains supply.
IMPORTANT: The wires in the mains lead are coloured in accord-ance with the following code:
Blue : NeutralBrown : Live
Do not connect those leads to the earth terminal of a three-pin plug.
For the United Kingdom
Microcomputer malfunctionIf operation is not possible or an erroneous display appears, eventhough all connections have been made properly, reset the microcom-puter referring to “In case of difficulty”. °
Maintenance of the unitWhen the front panel or case becomes dirty, wipe with a soft, drycloth. Do not use thinner, benzine, alcohol, etc. for these agents maycause discoloration.
In regard to contact cleanerDo not use contact cleaners because it could cause a malfunction.Be specially careful not to use contact cleaners containing oil, forthey may deform the plastic component.
*_4947/01-07/EN 3/15/01, 9:52 AM2
3
Oper
atio
nsPr
epar
atio
nsOt
her
Rem
ote
Cont
rol
Before applying the power
Contents
Before applying the power ................... 2Safety precautions .............................................. 2Unpacking .......................................................... 2How to use this manual ...................................... 4Special features .................................................. 4
Names and functions of parts ................ 5Remote control unit (RC-R0616)(KRF-V6050D) ..................................................... 6Remote control unit (RC-R0512)(KRF-V5050D) ..................................................... 7
Setting up the system ......................... 8Connecting audio components ........................... 9Connecting video components ......................... 10Connecting a DVD player (6 channel input) ...... 11Digital connections ........................................... 12Connecting to the AV AUX jacks(KRF-V6050D only) ........................................... 13Connecting the antennas .................................. 13Connecting the system control ......................... 14Connecting the speakers .................................. 15Preparing the remote control ............................ 17
Preparing for surround sound ............... 18Speaker settings ............................................... 18
Caution : Read the pages marked carefully to ensure safe operation.
Preparations
Operations
Remote Control
Normal playback .............................. 19Preparing for playback ...................................... 19Listening to a source component ..................... 20Adjusting the sound .......................................... 20
Recording ...................................... 21Recording audio (analog sources) .................... 21Recording video ................................................ 22Recording audio (digital sources) ...................... 22
Listening to radio broadcasts ............... 23Tuning (non-RDS) radio stations ....................... 23Using RDS (Radio Data System) ....................... 23Using the RDS DISP. (Display) key ................... 24Presetting RDS stations(RDS AUTO MEMORY) ..................................... 24Presetting radio stations manually .................... 25Receiving preset stations .................................. 25Receiving preset stations in order (P.CALL) ...... 25Tuning by program type (PTY search) .............. 26
Ambience effects .............................. 27Surround modes ............................................... 27Surround play ................................................... 29DVD 6-channel playback .................................. 30Convenient functions ........................................ 30
Basic remote control operations for othercomponents .................................... 32
Registering setup codes for othercomponents ...................................................... 32Operating other components ............................ 32Setup code chart(For KRF-V6050D (RC-R0616)) ......................... 33DVD player operations (For KRF-V5050D) ........ 34Cassette deck, CD player & MD recorderoperations (For KRF-V5050D) ........................... 35Cassette deck, CD player & MD recorderoperations (For KRF-V6050D) ........................... 36Other components' operations(For KRF-V6050D) ............................................ 37
Addi
tiona
l Inf
orm
atio
nRe
mot
e Co
ntro
l
AdditionalInformation
In case of difficulty ........................... 38Specifications ................................. 40
*_4947/01-07/EN 3/15/01, 9:52 AM3
4
Preparations
Special featuresHow to use this manual
This manual is divided into four sections, Preparations, Operations,Remote Control, and Additional Information.
PreparationsShows you how to connect your audio and video components to thereceiver and prepare the surround processor.We will guide you to make setting up your system as easy as possible.However, since this receiver works with all of your audio and videocomponents, connecting the system can be fairly complex.
OperationsShows you how to operate the various functions available from thereceiver.
Remote Control (KRF-V6050D only)Shows you how to operate other components using the remote control,as well as a detailed explanation of all remote control operations. Onceyou have registered your components with the proper setup codes, you’llbe able to operate both this receiver and your other AV components (TV,VCR, DVD player, CD player, etc.) using the remote control supplied withthis receiver.
Additional InformationShows you additional information such as “In case of difficulty” (trouble-shooting) and “Specifications”.
Before applying the power
The manual covers the KRF-V6050D and KRF-V5050D. Items such asfunctions, number of jacks, and remote control details differ somewhatbetween these models. To confirm the functions available on the modelyou have purchased, refer to the table below.
Memory back up functionPlease note that the following items will be deleted from the unit'smemory if the power cord is disconnected from the AC outlet forapproximately 2 days.
• Power mode.• Input selector settings.• Device preset.• Picture output.• Speaker ON/OFF• Volume level.• BASS, TREBLE, INPUT level.• Subwoofer ON/OFF.• Dimmer level.• Monitor ON/OFF.• MD/TAPE settings.
• 6ch/2ch input setting.• Listen mode setting.• Speaker settings.• Input mode setting.• Midnight mode setting.• Broadcast band.• Frequency setting.• Preset stations.• Tuning mode.• CINEMA EQ.• Source Direct.
True home theater soundThis receiver incorporates a wide variety of surround modes to bring youmaximum enjoyment from your video software. Select a surround modeaccording to your equipment or the software you are going to play andenjoy! ¶
Dolby Pro Logic & Dolby 3 StereoThis surround system reproduces theater-like surround sound fromvideo software marked .The PRO LOGIC mode uses the built-in adaptive matrix circuit to steerthe Left, Center, Right and Surround channel audio signals.The 3 STEREO mode will redirect the Surround signal to the front left andright speakers when only the front and center speakers are used.
Dolby DigitalThe DOLBY DIGITAL mode lets you enjoy full digital surround fromsoftware processed in the Dolby Digital format. Dolby Digital provides upto 5.1 channels of independent digital audio for better sound quality andmore powerful presence than conventional Dolby Surround.
DTSDTS (Digital Theater System) is a 5.1 channel digital audio format thatprovides five full-spectrum channels and one low-frequency (subwoofer)channel for unprecedented clarity, optimum channel separation and a(wide) dynamic range.In the DTS mode, the 5.1 channel digital input from a DTS CD, LD or DVDdisc (carrying the “DTS” marking) can be played in Digital Surround.Important:When a DTS disc is played on a CD, LD or DVD player, noise may beoutput from the analog output. It is recommended that you connect thedigital output of the player to the digital input of this unit.
DSP surround modesThe DSP (Digital Signal Processor) used for this receiver incorporates avariety of high quality adjustable sound fields, like “ARENA”, “JAZZCLUB”, “THEATER”, “STADIUM” and “DISCO” . It is compatible withalmost any kind of program source.
DVD 6-channel inputIf you own a DVD player equipped with 6-channel output, this receiverallows you to obtain the full surround sound impact of DVD sourcematerial featuring multi-channel encoding. Since the source signals aredigital and each channel is input independently, the resulting ambienceis far superior to what can be achieved with conventional surround soundsystems.
Universal IR (InfraRed) remote control (KRF-V6050D only)In addition to the basic receiver, the remote control supplied with thisreceiver can also operate almost all of your remote controllable audio andvideo components. Just follow the simple setup procedure to register thecomponents you have connected.
RDS (Radio Data System) tunerThe receiver is equipped with an RDS tuner that provides several conve-nient tuning functions: RDS Auto Memory, to automatically preset up to 40RDS stations broadcasting different programs; station name display, toshow you the name of the current broadcast station; and PTY search to letyou tune stations by program type.
PTY (Program TYpe) searchTune the stations by specifying the type of program you want to hear.
Model name Remote Terminal Control Speaker out Front input
KRF-V6050D RC-R0616 2 systems Equipped(A, B)
KRF-V5050D RC-R0512 1 system Not equipped
*_4947/01-07/EN 3/15/01, 9:52 AM4
5
Prep
arat
ions
CLIPTI.VOL
TPRDS EON PTY
TA NEWS
FMAMMHzkHz
PRO LOGIC3 STEREODOWNMIX
DIGITALS.DIRECTMONITOR
MEMOST.
TUNED
AUTO SOUND AUTOSP
LFE SW
CA BMUTE
S SRSL
RL
A SPEAKERS B
STANDBY
POWER
LISTEN MODESOUND
MULTI CONTROL
SOURCE DIRECT
AUTO/CINEMA EQ.BAND MEMORY
INPUT SELECTOR
VOLUME CONTROL
UPDOWN
DSP MODEDTS
INPUT MODESET UP
S-VIDEO V L – AUDIO – RAV AUX
DIMMER MONITOR
PHONES
ON/STANDBY
ON OFF
DOLBY D I G I T A L
SPEAKER MUTE
DSP
CLIP
RDS PTY
Display
Speaker selection indicatorsInput channel indicatorsOutput channel indicators
Band indicatorsAUTO indicator
TUNED indicator
3 STEREO indicatorSTEREO indicator
Names and functions of partsFrequency display,Input display,Preset channel display,Surround mode displaySpeaker indicators
PRO LOGICindicator
S.DIRECT indicator
MONITOR indicatorDOWNMIX indicator
MUTE indicator
AUTO SOUND indicator DIGITAL indicator
For KRF-V6050D
Standby mode
When standby indicator is lit, this receiver is in standby mode and consumes a small amount of current for back-up. This system can be switched on usingremote control.
For KRF-V5050D
1 POWER key *Use to switch the main power ON/OFF.
2 ON/STANDBY ( ) key *Use to switch the power ON/STANDBY whenthe POWER is turned ON.STANDBY indicator
3 MULTI CONTROL keys *Use to control a variety of settings.
4 SET UP key *Use to select the speakers' settings etc.
5 Surround indicatorsDTS indicator ªLights when the receiver is in the DTS mode.DOLBY DIGITAL indicator ªLights when the receiver is in the Dolby Digitalmode.DSP MODE indicatorLights when the receiver is in the DSP mode.
6 INPUT MODE key 8Use to switch between the digital and analoginputs.
7 DIMMER key ™⁄Use to adjust the brightness of the display.Use to select the REC MODE.
8 MONITOR key ¡Use to monitor the source that is connected tothe VIDEO2/MONITOR jack.
9 VOLUME CONTROL knob )0 PHONES jack ¡
Use for headphone listening.! SPEAKERS A/B keys )
(For KRF-V6050D)Use to turn the A/B speakers ON/OFF.
! SPEAKER key )(For KRF-V5050D)Use to turn the speakers ON/OFF.MUTE key ¡(For KRF-V5050D)Use to temporarily mute the sound.
@ SOUND key ºUse to adjust the sound quality and ambienceeffects.
# BAND key £Use to select the broadcast band.
$ AUTO/CINEMA EQ. key £Use to select the auto tuning mode.Use to switch the status of CINEMA EQ.
% LISTEN MODE key ªUse to select the listening mode.
^ MEMORY key ∞Use to store radio stations in the preset memory.
& SOURCE DIRECT key ¡Use to pass the source material direct to theamplifier.
* INPUT SELECTOR knob )Use to select the input sources.
( AV AUX (S VIDEO, V, AUDIO L/R) jack(For KRF-V6050D) #
DSP indicatorRDS indicators
CLIP indicatorMEMO. indicator
ST. indicator
*_4947/01-07/EN 3/15/01, 9:52 AM5
6
Preparations
Remote control unit (RC-R0616) (KRF-V6050D)
If the name of a function is different onthe receiver and on the remote control,the name of the remote control key inthis manual is indicated in parentheses.
Names and functions of parts
7 B. BOOST key )Use to select the maximum adjustment settingfor the low frequency range.RECEIVER keyUse to return to the operation of the receiver.
8 DISC SKIP keyIf CD is selected as the input source, this keyfunctions as the multi-CD player disc skip key.A/B keyIf TAPE is selected as the input source, this keyfunctions as the A and B play keys of a doublecassette deck.+100 keyUse to select the disc number with the multi-CD player.
9 TITLE keyUse to operate other components.
0 TV SEL. keyUse to operate other components.
! INPUT SELECTOR keys (DVD, PHONO,CD/DVD, TUNER, MD/TAPE, VIDEO1,VIDEO2, AV AUX) )Use to select the input sources.4 DVD ¢ keysWhen in DVD player operations, these keysfunction as skip keys.
@ MUTE key ¡Use to temporarily mute the sound.
# POWER ( )key &Use to turn the receiver on and off.
$ POWER key (TV, VCR, DVD)Use to turn the other components on and off.
% PTY key §Use for PTY search.RDS DISP. key ¢Use to receive RDS broadcasts.
^ ENTER keyUse to operate other components.2 keyIf tape is selected as the input source, this keyfunctions as the play key for side B of thecassette (the side facing away from the front ofthe deck).
& BAND key £Use to select the broadcast band.6 keyIf CD is selected as the input source, this keyfunctions as the play/pause key.If MD or TAPE is selected as the input source,this key functions as the play key.
* AUTO key £Use to select the auto tuning mode.7 keyIf CD, MD or TAPE is selected as the inputsource, this key functions as the stop key.
( 8 keyUse to operate other components.
) INPUT SEL. keyUse to operate other components.
¡ CHANNEL %/fi keysUse to select the channel.
™ CINE. EQ keyUse to switch the status of CINEMA EQ.DISC SEL. keyUse to operate other components.
£ VOLUME keys ¡Use to adjust the receiver volume.
1 Numeric keys fiProvide functions identical to those of the origi-nal remote control supplied with the compo-nent you are controlling.
2 LSTN M. key ªUse to select the listening mode.RETURN keyUse to operate other components.
3 SET UP key *Use to select speakers' settings etc.MENU keyUse to operate other components.
4 SOUND key ºUse to adjust the sound quality and ambienceeffects.OSD keyUse to operate other components.
5 MULTI CONTROL keys *Use to control a variety of settings.Use to operate other components.P.CALL 4/¢ keys ∞If tuner is selected as the input source, thesekeys function as P.CALL keys.4/¢ keysIf CD or MD is selected as the input source,these keys function as skip keys.
6 TUNING 1/¡ keysUse to operate the tuner or selected compo-nent.If CD, MD or TAPE is selected as the inputsource, these keys function as search keys.
1
B.BOOST DISC SKIP DVD
PHONO CD/DVD TUNER MD/TAPE
VIDEO1 VIDEO2 CINE.EQ AV AUX
2 3
POWER
RDS DISP.PTY
RETURN
OSDMENU
P.CALL
TUNING
MUTE VOLUME
A/B+100
TITLE TV SEL.RECEIVER
AUTO
INPUT SEL.
DISC SEL. CHANNEL
ENTER BAND
P.CALL
MULTI CONTROL
4 5 6
7 8 9
0 +10 LSTN M.
SET UP SOUND
™
POWER
TV
DVD
VCR
#
$
%
(
¡
£
&^
*
)
™
1
7
!
890
@
2
43
5
6
DVD
This remote control unit can be used not only for Kenwood products but also for other non-Kenwood products bysetting the appropriate maker setup codes. ‹
*_4947/01-07/EN 3/15/01, 9:52 AM6
7
Prep
arat
ions
Names and functions of parts
Remote control unit (RC-R0512) (KRF-V5050D)
A/B keyIf TAPE is selected as the input source, this keyfunctions as the A and B play keys of a doublecassette deck.+100 keyUse to select the disc number with the multi-CD player.
8 INPUT SELECTOR keys (DVD, PHONO, CD/DVD, TUNER, MD/TAPE, VIDEO1, VIDEO2)
)Use to select the input sources.
9 MUTE key ¡Use to temporarily mute the sound.
0 POWER ( ) key &Use to turn the receiver on and off.
! DVD POWER key ›Use to operate DVD player.For details, refer to the instruction manual ofyour DVD player. (Press the DVD POWER keyfor more than 2 seconds.)4 DVD ¢ keysWhen in DVD player operations, these keysfunction as skip keys.
@ RECEIVER keyUse to return to the operation of the receiver.
# TITLE keyUse to operate other components.PTY key §Use for PTY search.RDS DISP. key ¢Use to receive RDS broadcasts.
1 Numeric keys ∞If CD or MD is selected as the input source,these keys function as numeric keys. If tuner isselected as the input source, these keys areused to call up station presets.
2 SET UP key *Use to select speakers' settings etc.MENU keyUse to operate other components.
3 SOUND key ºUse to adjust the sound quality and ambienceeffects.OSD keyUse to operate other components.
4 MULTI CONTROL keys *Use to control a variety of settings.P.CALL 4/¢ keys ∞If tuner is selected as the input source, thesekeys function as P.CALL keys.4/¢ keysIf CD or MD is selected as the input source,these keys function as skip keys.
5 TUNING 1/¡ keysIf tuner is selected as the input source, thesekeys function as tuning keys.If CD, MD or TAPE is selected as the inputsource, these keys function as search keys.
6 BASS BOOST key )Use to select the maximum adjustment settingfor the low frequency range.
7 DISC SKIP keyIf CD is selected as the input source, this keyfunctions as the multi-CD player disc skip key.
1
DISC SKIP
DISC SEL.CINE.EQ
BASS BOOSTAUTO
PHONO CD/DVD TUNER MD/TAPE
VIDEO1 VIDEO2
2 3
POWER
DVD
POWER
RECEIVER
MENU
P.CALL
TUNING
MUTE VOLUME
A/B+100DVD
ENTER BAND
P.CALL
MULTI CONTROL
4 5 6
7 8 9
0 +10
SET UPOSD
SOUNDRETURN TITLE
LISTEN MODE
1
6
8
7
9
32
4
5
0
!
@
#
$RDS DISP.
PTY
DVD
)
&
^%
*
(
$ LISTEN MODE key ªUse to select the listening mode.RETURN keyUse to operate other components.
% ENTER keyUse to operate other components.2 keyIf tape is selected as the input source, this keyfunctions as the play key for side B of thecassette (the side facing away from the front ofthe deck).
^ BAND key £Use to select the broadcast band.6 keyIf CD is selected as the input source, this keyfunctions as the play/pause key.If MD or TAPE is selected as the input source,this key functions as the play key.
& 8 keyUse to operate other components.
* AUTO key £Use to select the auto tuning mode.7 keyIf CD, MD or TAPE is selected as the inputsource, this key functions as the stop key.
( CINE.EQ keyUse to switch the status of CINEMA EQ.DISC SEL. keyUse to operate other components
) VOLUME keys ¡Use to adjust the receiver volume.
*_4947/01-07/EN 3/15/01, 9:52 AM7
8
Preparations
Make connections as shown in the following pages.When connecting the related system components, be sure toalso refer to the instruction manuals supplied with thecomponents you are connecting.Do not connect the power cord to a wall outlet until allconnections are completed.
Setting up the system
Analog connectionsAudio connections are made using RCA pin cords. These cables transferstereo audio signal in an “analog” form. This means the audio signalcorresponds to the actual audio of two channels. These cables usually have2 plugs on each end, one red for the right channel and one white for the leftchannel. These cables are usually packed together with the source unit, orare available at your local electronics retailer.
Notes1. Be sure to insert all connection cords securely. If their connections are
imperfect, the sound may not be produced or noise may interfere.2. Be sure to remove the power cord from the AC outlet before plugging or
unplugging any connection cords. Plugging/unplugging connection cordswithout disconnecting the power cord can cause malfunctions and maydamage the unit.
3. Do not connect power cords from components whose power consump-tion is larger than what is indicated on the AC outlet at the rear of this unit.
VIDEO 2/MONITOR jacksThe receiver’s VIDEO 2/MONITOR jacks can be used in two differentways. Make the appropriate setting for the component connected to thejack when the receiver is turned on.
Use as a VIDEO 2 jackYou can connect a video deck or the like to these jacks and performvideo playback and recording. The initial factory setting is “VIDEO 2”.
Use as a MONITOR jackYou can connect a cassette deck or the like to these jacks and make useof the deck’s monitoring function during recording. Alternately, you canconnect a graphic equalizer to these jacks to apply compensation to themusic signal.To use the VIDEO 2/MONITOR jacks as MONITOR jacks, hold downthe MONITOR key of the main unit for more than two seconds so thatthe indication shown below appears.
• To switch the setting back to “VIDEO 2”, once again hold down theMONITOR key for two seconds or more.
TUNED
AUTOFM
MHzAM
kHz
PRO LOGIC3 DOWN MIX
DIGITALS.DIRECT
DSP
AUTO SOUND
LFE
C
S
TI.VOLBCLIP MUTERDS EON PTYTP TA NEWS
STEREO ST.MEMO
SW
RLSP A
MONITOR
MONITOR
DTS Digital Surround™ is a discrete 5.1 channel digital audio formatavailable on CD, LD, and DVD software which consequently cannot bedecoded and played back inside most CD, LD, or DVD players. For thisreason, when DTS-encoded software is played back through the analogoutputs of the CD, LD, or DVD player, excessive noise will be exhibited.To avoid possible damage to the audio system, proper precautionsshould taken by the consumer if the analog outputs are connecteddirectly to an amplification system. To enjoy DTS Digital Surround™playback, an external 5.1 channel DTS Digital Surround™ decodersystem must be connected to the digital output (S/P DIF, AES/EBU, orTosLink) of the CD, LD or DVD player.
DTS disclaimer clause
Input mode settingsCD/DVD, VIDEO2 and DVD/6ch inputs each include jacks for digitalaudio input and analog audio input.You must select beforehand which type of input is to be used for eachconnected component.The initial factory settings for audio signal playback (CD/DVD,DVD/6ch) and (VIDEO2) are digital and analog respectively.To use the analog audio input for playback instead (if, for example, youhave connected a VCR to the VIDEO2 input), you must set the inputmode for the corresponding input to the analog mode.After completing connections and turning on the receiver, follow thesteps below.
1 Use the INPUT SELECTOR knob to select CD/DVD, VIDEO2, orDVD/6ch.
2 Press the INPUT MODE key.
Each press switches the setting as follows:
In DTS play mode1 D-AUTO (digital input, auto sound)2 D-MANUAL (digital input, manual sound)
In DVD/6ch play mode1 D-AUTO (digital input, auto sound)2 D-MANUAL (digital input, manual sound)3 6ch INPT (DVD/6ch input)4 ANALOG (analog input, manual sound)
In modes other than DTS or DVD play mode1 D-AUTO (digital input, auto sound)2 D-MANUAL (digital input, manual sound)3 ANALOG (analog input, manual sound)
Digital input:Select this setting to play digital signals from a DVD, CD, or LD player.
Analog input:Select this setting to play analog signals from a cassette deck, VCR,or turntable.
Auto sound:In the auto sound mode (AUTO SOUND indicator lights), the receiverselects the listening mode automatically during playback to match thetype of input signal (Dolby Digital, PCM, DTS ) and the speaker setting.The initial factory setting is auto sound on.To keep the receiver set to the currently selected listening mode, usethe INPUT MODE key to select “D-MANUAL” (manual sound).However, even when this setting is selected, there may be cases inwhich the listening mode is selected automatically to match a DolbyDigital source signal depending on the combination of listening modeand source signal.If the INPUT MODE key is pressed quickly, sound may not beproduced.
INPUT MODE
INPUT SELECTOR
*_4947/08-17/EN 3/15/01, 9:53 AM8
9
Prep
arat
ions
L
RA
L CLR
LRB
R
PLAY IN
AUDIO
L
R
MD/TAPEPHONOGND
REC OUT REC OUT PLAY IN
CD/DVD VIDEO 2/MONITOR
Connecting audio components
To AC wall outlet
CD player
IN OUT
SYSTEM CONTROLjacks $
IN
OUT
When you connect the audio cord of the video component to the VIDEO2/ MONITOR jacks, connect the video cord (yellow RCA pin cords)of the connected component to the VIDEO2 IN jack.
Record player
Shape of AC outlets
U. K.
Europe
Setting up the system
Moving Coil (MC) cartridgerecord player cannot be useddirectly from the receiver unit.It can only be used whenanother equalizer amplifier isconnected.
Video component,3 head cassette deck, orGraphic equalizer ¡
Cassette deck orMD recorder
OUT
OUT
*_4947/08-17/EN 3/15/01, 9:53 AM9
10
Preparations
L
VIDEO 1
S VIDEO
RA
L CLR
LRB
PLAY INREC OUTPLAY IN
MONITOROUT VIDEO 1DVD
R
VIDEO 2/MONITOR VIDEO 1PLAY IN PLAY INREC OUT
MD / TAPEAUDIO
PLAY INREC OUT
S VIDEO
DVD VIDEO 1 VIDEO 1MONITOR
OUT
PLAY IN REC OUT PLAY IN
VIDEO 2 INVIDEO
MONITOROUT
VIDEO 1OUT
VIDEO 1 IN
CD/DVDDVD IN
REC OUTCD / DVD
Connecting video components
OUT
Video Inputs(Yellow RCA pin cord)
Video inputs and outputs(Yellow RCA pin cords)
Setting up the system
Video deck
Monitor TV
OUT
IN
Audio inputs andoutputs
A video component with digital audio outputs should be connected to the VIDEO2 jacks.
VIDEOIN
S Video jacks(KRF-V6050D only)
About the S VIDEOjacks
Use the S VIDEO jacks tomake connections tovideo components with SVIDEO IN/OUT jacks.
÷ If you use the S VIDEOjacks to connect your videoplayback components, besure to use the S VIDEOjacks when connectingyour monitor and videorecording components.
S VIDEO
DVD player or LD player
IN
OUT
OUT
IN
*_4947/08-17/EN 3/15/01, 9:54 AM10
11
Prep
arat
ions
L
VIDEO 1
S VIDEO
RA
L CLR
LRB
PLAY INREC OUTPLAY IN
MONITOROUT VIDEO 1DVD
R
DVD
PLAY IN
FRONT
L CENTER DVD
SURROUNDSUB
WOOFERDVD/6CH. INPUT
R
VIDEO 2 INVIDEO
MONITOROUT
VIDEO 1OUT
VIDEO 1 IN
CD/DVDDVD IN
VIDEO 2/MONITORCOAXIAL
Connecting a DVD player (6-channel input)
FRONTOUT L/R
S VIDEOOUT
COAXIALDIGITALOUT(AUDIO)
DVD player
S VIDEO cord
SURROUNDOUT L/R
VIDEO OUT(Yellow RCApin cord)
CENTER OUT
SUBWOOFER OUT
If you have connected a DVD player to the receiver with digital connection, be sure to read the “Input mode settings”section carefully. 8
Be sure to adhere followings. Or proper ventilation will be blocked causing damage or fire hazard.• Do not place any objects impairing heat radiation onto the top of unit.• Leave a space around the unit (from the largest outside dimension including projection) equal or greater than, shown below.
Top panel : 50 cm Side panel : 10 cm Back panel : 10 cm
CAUTION
To switch the speakers off , press the MUTE key.
Setting up the system
*_4947/08-17/EN 3/15/01, 9:54 AM11
12
Preparations
L
VIDEO 1
S VIDEO
RA
L CLR
LRB
PLAY INREC OUTPLAY IN
MONITOROUT DVD
R
OPTICAL
DVD
CD/DVDVIDEO 2/MONITORCOAXIAL
DIGITAL IN
Digital connections
COAXIAL DIGITAL OUT (AUDIO)
Optical fibercable
Connect the video signal and analogaudio signals to the VIDEO 2 jacks.(See “Connecting video components”.)
0
DOLBY DIGITALRF OUT (AUDIO)
LD player
RF digitaldemodulator(DEM-9991D)(sold separately)
PCM OUT
CD player
Component with a DTS,Dolby Digital, or PCMCOAXIAL DIGITAL OUT
OPTICAL DIGITAL OUT (AUDIO)
Setting up the system
The digital in jacks can accept DTS, Dolby Digital, or PCM signals. Connect components capable of outputting DTS,Dolby Digital, or standard PCM (CD) format digital signals.If you have connected any digital components to the receiver, be sure to read the “Input mode settings” sectioncarefully. 8
To connect an LD player with a DIGITAL RF OUT, connect the LD player to the KENWOOD RF digital demodulator (DEM-9991D).Next, connect the DIGITAL OUT jacks of the demodulator to the DIGITAL IN jacks of the receiver.Connect the video signal and analog audio signals to the VIDEO2/MONITOR jacks. (See “Connecting video components”.)
COAXIAL DIGITAL OUT (AUDIO)
*_4947/08-17/EN 3/15/01, 9:54 AM12
13
Prep
arat
ions
VIDEO 1
S VIDEO
RA
L CLR
LRB
PLAY INREC OUTPLAY IN
MONITOROUT VIDEO 1DVD
R
FM75Ω
GND
ANTENNA
AM
S VIDEO V L – AUDIO – RAV AUX
Setting up the system
The AV AUX jacks are convenient for connection of video componentssuch as a camcorder or a video game.
Connecting to the AV AUX jacks(KRF-V6050D only)
S VIDEO OUT
Camcorder, other VCR,video game, digital camera,or portable MD player
S VIDEO cord
VIDEO OUT
AUDIO OUT
Connecting the antennas
AM antenna terminal connections1 Push lever. 2 Insert cord.
AM loop antennaThe supplied loop antenna is for use indoors. Place it as far as possible fromthe receiver, TV set, speaker cords and power cord, and adjust the directionfor best reception.
3 Release lever.
AM loop antenna
FM indoor antenna
FM outdoor antenna
Use an antennaadaptor(Commerciallyavailable)
FM indoor antennaThe supplied indoor antenna is for temporary use only. For stable signalreception we recommend using an outdoor antenna. Disconnect the indoorantenna when you connect one outdoors.
FM outdoor antennaLead the 75Ω coaxial cable connected to the FM outdoor antenna into theroom and connect it to the FM 75Ω terminal.
• To select the source connected to the AV AUX jacks, select AVAUX by using the INPUT SELECTOR knob. )
• When you connect the audio source such as the MD player, youdo not need to connect the video cable.
• When you connect the unit and the component with the SVIDEO cord, you can get better picture quality.
Attach to the stand.
FM antenna terminal connectionsInsert cord.
*_4947/08-17/EN 3/15/01, 9:54 AM13
14
Preparations
Connecting the system control
Setting up the system
Do not connect a system control cord to a cassette deck con-nected to the VIDEO2/MONITOR jacks.
Connecting system control cords after connecting a KENWOODaudio component system lets you take advantage of convenientsystem control operations.
This unit is compatible only with the [SL-16] mode. The systemcontrol operation is not available if the unit is connected in the[XS8], [XS], or [XR] connection mode.
If your component has the mode select switch, set the connectedcomponents to the [SL16] mode.
[SL16]
[SL16] [XS] [XS8] [XR]
[SL16] [XS] [XS8]
[XS]
SYSTEMCONTROLcord
Receiver
Cassette deckor MD recorder
CD player
Record player
• In order to take advantage of the system control operations, thecomponents must be connected to the correct jacks. To use a CDplayer it must be connected to the CD jacks. To use a cassette deck(or MD recorder) it must be connected to the MD/TAPE jacks. Whenusing more than one CD player (etc.) only the one connected to thespecified jacks may be connected for system control.
• Some CD players and cassette decks are not compatible with the[SL16] system control mode. Do not make system connections withequipment that is not [SL16] compatible.
• Some MD players are not system control compatible. You cannotmake system control connections to this kind of equipment.
Notes1. [SL16] equipment cannot be combined with [XR], [XS], and [XS8]
equipment for system operations. If your equipment consists of thiskind of combination, please do not connect any system control cords.Even without system control cords, normal operations can be carriedout without effecting performance.
2. Do not connect system control cords to any components other thanthose specified by KENWOOD. It may cause a malfunction anddamage your equipment.
3. Be sure the system control plugs are inserted all the way in to thesystem control terminals.
EXAMPLE: [SL16] mode connectionsThe underlined portion represents the setting of the system controlmode.
SYSTEM CONTROLcord
SYSTEMCONTROL
• You may connect the system control cord to either the left or right jack.
SYSTEM CONTROL OPERATIONSRemote ControlLets you operate this unit with the system remote supplied with thereceiver.
Automatic OperationWhen you start playback from a source component, the input selectoron this unit switches to that component automatically.
Synchronized RecordingLets you synchronize recording with the start of playback when record-ing from CD, MD or analog discs.
Registering setup codes for KENWOOD audio components(KRF-V6050D only)
• If you own remote controllable KENWOOD audio components that arenot compatible with system control, registering the setup code en-ables you to control those components using the remote controlsupplied with this unit (without connecting system control cords). Toregister setup codes for your remote controllable KENWOOD audiocomponents, see “Registering setup codes for other components”.
‹
*_4947/08-17/EN 3/15/01, 9:54 AM14
15
Prep
arat
ions
Setting up the system
• Never short circuit the + and – speaker cords.• If the left and right speakers are connected inversely or the speaker
cords are connected with reversed polarity, the sound will be unnatu-ral with ambiguous acoustic imaging. Be sure to connect the speak-ers correctly.
Connecting the speakers
Speaker impedanceAfter confirming the speaker impedance indications printed on the rearpanel of the receiver, connect speakers with matching impedanceratings. Using speakers with a rated impedance other than that indi-cated on the rear panel of the receiver could result in malfunctions ordamage to the speakers or receiver.
1 Strip coating. 2 Loosen.
3 Insert. 4 Secure.
1 Strip coating. 2 Push the lever.
3 Insert the cord. 4 Return the lever.
*_4947/08-17/EN 3/15/01, 9:54 AM15
16
Preparations
L
VIDEO 1
S VIDEO
RA
L CLR
LRB
PLAY INREC OUTPLAY IN
MONITOROUT VIDEO 1DVD
R
FRONT SPEAKERS CENTER SPEAKER
SUB WOOFERPRE OUT
+ +
FRONT SPEAKERS
SURROUND SPEAKERS
(6 – 16Ω)
(6 – 16Ω)
RED BLUE GREEN
GRAYORANGE
SURROUND SPEAKERS(6 – 16Ω)
GRAYORANGE
+
-
FRONT SPEAKERS CENTER SPEAKERRED BLUE GREEN
Right
Front Speakers A
LeftRight
Use the FRONT SPEAKERS Bterminals if you want to connecta second front speaker system(for KRF-V6050D only).
Left
(Be sure to connect both surround speakers)
CenterSpeaker
Surround Speakers
Poweredsubwoofer
The KRF-V5050D is equipped with one-touch speaker terminals.They are arrangedin the same manner as the speakerterminals of the KRF-V6050D. Refer to theinstructions on making connections to theKRF-V6050D when making connections tothe KRF-V5050D.
KRF-V6050D
Setting up the system
Connecting the speakers
KRF-V5050D
KRF-V5050DKRF-V6050D
*_4947/08-17/EN 3/15/01, 9:54 AM16
17
Prep
arat
ions
Speaker placement
Subwoofer
Front speakers : Place to the front left and right of the listening position.Front speakers are required for all surround modes.Center speaker : Place front and center. This speaker stabilizes thesound image and helps recreate sound motion. Be sure to connect acenter speaker when using the Dolby 3 Stereo mode.Surround speakers : Place to the direct left and right, or slightlybehind, the listening position at even heights, approximately 1 meterabove the ears of the listeners. These speakers recreate sound motionand atmosphere. Required for surround playback.Subwoofer : Reproduces powerful deep bass sounds.
Frontspeaker
Center speaker
ListeningpositionSurround
speaker
• Although the ideal surround system consists of all the speakers listedabove, if you don't have a center speaker or a subwoofer, you candivide those signals between the available speakers in the speakersettings steps to obtain the best possible surround reproduction fromthe speakers you have available. *
Setting up the system
Loading the batteries
Preparing the remote control
• Insert two AA-size (R6) batteries as indicated by the polarity markings.
3 Close the cover.
2 Insert the batteries.1 Remove the cover.
Notes1. The supplied batteries may have shorter lives than ordinary batteries due
to use during operation checks.2. When the remote-controllable distance gets shorter than before, replace
both batteries with new ones.3. Placing the remote sensor in direct sunlight, or in direct light from a high
frequency fluorescent lamp may cause a malfunction.In such a case, change the location of the system installation to preventmalfunction.
Remote sensor
Infrared ray system
6 m
• When pressing more than one remote control key successively, pressthe keys securely by leaving an interval of 1 second or more betweenkeys.
Operation
When the STANDBY indicator is lit, the power turns ON when you pressthe POWER key on the remote control. When the power comes ON,press the key you want to operate.
Operating range(Approx.)
12
*_4947/08-17/EN 3/15/01, 9:54 AM17
18
Preparations
Speaker settings
Turn on the power to this receiver by pressing POWER orON/STANDBY key.
Select a speaker system.
1
2
1 Press the SET UP key such that the subwoofer settingindication (SUBW ON) appears.
2 Use the MULTI CONTROL keys to select the appropriatesubwoofer setting.
1 SUBW ON: Subwoofer setting mode to the receiver is ON.2 SUBW OFF: Subwoofer setting mode to the receiver is OFF.
• The initial setting is “SUBW ON”.• When “SUBW OFF” is selected, the front speakers are automatically
set to “FRNT LRG” and the procedure skips to step 5.• When subwoofer output sound is required, select “FRNT NML”.
3 Press the SET UP key again to accept the setting.• The front speakers setting indication (FRNT) appears.
4 Use the MULTI CONTROL keys to select the appropriate frontspeakers setting.
1 FRNT NML (normal): Average size front speakers areconnected to the receiver.
2 FRNT LRG (large): Large front speakers are con-nected to the receiver.
• For “FRNT LRG” selection, no sound will be heard from SUBWeven when it is set to ON. However, if you select CINEMA EQ.when subwoofer is selected, you will be able to hear sound fromthe subwoofer.When in STEREO mode, the sound goes directly to front speaker.
5 Press the SET UP key again to accept the setting.• The center speaker setting indication (CNTR) appears.
To enable you to obtain optimum enjoyment from the receiver’s listeningmodes, make sure to complete the speaker settings (subwoofer, front,center, and surround speakers) as described below.
If you have selected “NML” as the front speakers setting,1 CNTR ON: Center speaker setting mode to the receiver
is ON.2 CNTR OFF: Center speaker setting mode to the receiver
is OFF.
7 Press the SET UP key again to accept the setting.• The surround speaker setting indication (SURR) appears.
8 Use the MULTI CONTROL keys to select the appropriatesurround speaker setting.
If you have selected “LRG” as the center speaker setting,1 SURR LRG (large): Large surround speakers are con-
nected to the receiver.2 SURR NML (normal): Average size surround speakers are
connected to the receiver.3 SURR OFF: Surround speaker setting mode to the
receiver is OFF.
FMAMMHzkHz
PRO LOGIC3 DOWN MIX
DIGITALS.DIRECTMONITOR
DSP
MEMOST.
TUNED
AUTO SOUND AUTO
LFE
C
S RSLS
TI.VOLBCLIP MUTERDS EON PTYTP TA NEWS
SW
RLSP A
STEREO
6 Use the MULTI CONTROL keys to select the appropriate centerspeaker setting.
If you have selected “LRG” as the front speakers setting,1 CNTR LRG (large): A large center speaker is connected to
the receiver.2 CNTR NML (normal): An average size center speaker is con-
nected to the receiver.3 CNTR OFF: Center speaker setting mode to the
receiver is OFF.
Preparing for surround sound
If you have selected other than “LRG” as the center speakersetting,
1 SURR ON: Surround speaker setting mode to thereceiver is ON.
2 SURR OFF: Surround speaker setting mode to thereceiver is OFF.
9 Press the SET UP key again to accept the setting.• The receiver enters the speaker volume level adjustment mode.• In steps 3 and 4, indications appear only for the selected channels
of the speakers that require adjusting.
FMAMMHzkHz
PRO LOGIC3 DOWN MIX
DIGITALS.DIRECTMONITOR
DSP
MEMOST.
TUNED
AUTO SOUND AUTO
LFE
C
S RSLS
TI.VOLBCLIP MUTERDS EON PTYTP TA NEWS
SW
RLSP A
STEREO
MULTI CONTROL
SET UP
RC-R0616
SET UP
RC-R0512
MULTI CONTROL
POWER ON/STANDBY
The channel indication blinks while the test tone is being output.
STEREO
RFMAMMHzkHz
PRO LOGIC3 DOWN MIX
DIGITALS.DIRECTMONITOR
DSP
MEMOST.
TUNED
AUTO SOUND AUTO
LFE
C
S RSLS
TI.VOLBCLIP MUTERDS EON PTYTP TA NEWS
LSP A
3 Adjust the speaker volume.From your usual listening position, adjust the volume levels. Thevolume levels from each speaker should be the same.
1 Use the MULTI CONTROL keys to adjust the volume of thetest tone output from the speaker channel to be adjusted.
The test tone is heard from the speakers for 2 seconds ata time in the following sequence for 2 seconds each:
L = C = R = SR = SL = SW
• If you change the volume level settings for the speakers whilelistening to music, the settings referred to on this page are alsochanged. º
• If the speaker setting selects are changed, the speaker levelsettings are reset.
2 Press the SET UP key.• The test tone is turned off. The receiver enters the mode for
inputting the distance to the speakers.
*_4947/18-20/EN 3/15/01, 9:55 AM18
19
Oper
atio
ns
Preparing for surround sound
Input level adjustment (analog sources only)
If the input level of an analog source signal is too high, adjust the inputlevel. The CLIP indicator will blink to indicate the source signal.
1 Use the INPUT SELECTOR knob to select the input level of thesource you want to adjust.
• You can store a separate input level for each input source. If theMONITOR function is on, you can store an input level for whenMONITOR is on independently of the input levels for the inputsources.
2 Press the SOUND key repeatedly until the “INPUT” indicationappears.
3 Use the MULTI CONTROL keys to adjust the input level.
• The adjustment mode is displayed for approximately eight seconds.• The input level may be adjusted to any one of three settings: 0dB,
-3dB, and -6dB. (The initial setting is 0dB.)
4 Press the SOUND key again to return to the input indication.
Preparing for playback
Normal playback
Some preparatory steps are needed before starting playback.
Turning on the receiver
1 Turn on the power to the related components.
2 Turn on the power to this receiver by pressing POWER (and ON/STANDBY) keys.
Selecting MD/TAPESelect the source name corresponding to the component connected tothe MD/TAPE jacks. The initial factory setting is “TAPE”. To change thesource name to “MD,” follow the steps below:
1 Use the INPUT SELECTOR knob to select “TAPE”.
2 Hold down the AUTO/CINEMA EQ. key for more than 2 seconds.
• The source indication changes to “MD”.• To return to the original indication, repeat procedure 2.
A ON : Sound from the speakers connected to the SPEAKERS Aterminals on the rear panel.
B ON : Sound from the speakers connected to the SPEAKERS Bterminals on the rear panel.
A+B ON : Sound from both the speakers connected to theSPEAKERS A and B terminals on the rear panel.
A+B OFF : No sound from the speakers. Use this setting when listeningwith headphones for stereo sound in all playback modes.
Selecting the input mode
If you have selected a component connected to the CD/DVD, DVD/6ch,or VIDEO2/MONITOR jacks, make sure that the input mode setting iscorrect for the type of audio signal to be used. 8
5 Setup is complete when the input indication reappears.
Display when all speakers have been selected.
• The speakers you have selected should appear on the display.Confirm that all the speakers have been correctly selected.
4
The speaker indicator to be adjusted blinks.
Indication in feet Indication in meters
1 Measure the distance from the listening position to each of thespeakers.
Jot down the distance to each of the speakers.Distance to front speakers: ____ feet (meters)Distance to center speaker: ____ feet (meters)Distance to surround speakers: ____ feet (meters)
2 Use the MULTI CONTROL keys to select the distance to thefront speakers.
• The allowable setting range is 1 to 30 feet (0.3 to 9.0 m), adjustablein 1 foot (0.3 m) increments.
3 Press the SET UP key to accept the settings.
4 Repeat steps 2 and 3 to input the distance for each of thespeakers.
Input the distance to the speakers.
LFE
C
S RSLS
TI.VOLBCLIP MUTERDS EON PTYTP TA NEWS
LSP A RSW
SW STEREO
FMAMMHzkHz
PRO LOGIC3 DOWN MIX
DIGITALS.DIRECTMONITOR
DSP
MEMOST.
TUNED
AUTO SOUND AUTO
LFE
C
S RSLS
TI.VOLBCLIP MUTERDS EON PTYTP TA NEWS
LSP A R
STEREO
STEREO
FMAMMHzkHz
PRO LOGIC3 DOWN MIX
DIGITALS.DIRECTMONITOR
DSP
MEMOST.
TUNED
AUTO SOUND AUTO
LFE
C
S RSLS
TI.VOLBCLIP MUTERDS EON PTYTP TA NEWS
LSP A RSTEREOSW
AUTO/CINEMA EQ.INPUT MODE
POWER
ON/STANDBY
INPUT SELECTOR
LFE
C
S RSLS
TI.VOLCLIP MUTERDS EON PTYTP TA NEWS
LSP A RSW
B
Selecting the speaker system (KRF-V6050D only)
Press the SPEAKERS A or B key to select the speaker system tobe used.
LFE
C
S RSLS
TI.VOLCLIP MUTERDS EON PTYTP TA NEWS
LSP A RSW
B
The speaker indicator lights.
KRF-V5050DKRF-V6050D
The indicator for the speakersyou want to use should be lit.
• Selecting “6ch INPT” by pressing the INPUT MODE key, whereby“DVD/6ch” is the input source, will cause SPEAKER A to be selectedautomatically.
On the KRF-V5050D, press the SPEAKER key to switch the speak-ers on and off.
Speakers A/B (SPEAKER/MUTE)
RDSTP
CLIP
*_4947/18-20/EN 3/15/01, 9:55 AM19
20
Operations
1 “PHONO”2 “TUNER”3 “CD/DVD”4 “TAPE” or “MD”5 “VIDEO1”
if VIDEO2/MONITOR is VIDEO26 “VIDEO2”7 “DVD/6ch”
else if VIDEO2/MONITOR is MONITOR6 “DVD/6ch”
KRF-V5050D
Normal playback
1
Listening to a source component Adjusting the sound
Adjusting the tone
You can adjust the sound quality when the receiver is in the PCM stereoand analog stereo mode.
• The bass and treble levels are adjustable from -10dB to +10dB in 2step increments.
• The adjustment item is displayed for approximately 8 seconds.
Use the INPUT SELECTOR to select the source you want tolisten to.
2 Use the MULTI CONTROL keys to adjust the sound quality.
BASS: Select this to adjust the low frequency range.(Press the SOUND key once.)
TREB: Select this to adjust the high frequency range.(Press the SOUND key twice.)
Once-touch low frequency emphasis (bass boost)(remote control only)
You can adjust the sound quality when the receiver is in the PCM stereoand analog stereo mode.
Press the B. BOOST (BASS BOOST) key.
• Press the key once to select the maximum (+10dB) low frequencyemphasis setting.
• This key does not function when the receiver is in the sound quality orambience effects adjustment mode.
Switching back to the previous settingPress the B. BOOST (BASS BOOST) key again.
FMAMMHzkHz
PRO LOGIC3 DOWN MIX
DIGITALS.DIRECTMONITOR
DSP
MEMOST.
TUNED
AUTO SOUND AUTO
LFE
C
S RSLS
TI.VOLBCLIP MUTERDS EON PTYTP TA NEWS
SW
LSP A R
STEREO
The input sources change as shown below:Selecting a source using the INPUT SELECTOR knob.
2
3
Start playback from the selected source.
Use the VOLUME CONTROL knob (VOLUME keys) to adjustthe volume.
Selecting VIDEO 2/MONITOR
Depending on the component connected to the VIDEO 2/MONITORjacks, select either the “VIDEO 2” setting or the “MONITOR” setting, asappropriate. 8
INPUT SELECTOR
INPUT SELECTORVOLUME CONTROL
VOLUME
RC-R0616 RC-R0512
1 Press the SOUND key to select the tone mode to be adjusted.
RC-R0616 RC-R0512
SOUND
VOLUME CONTROL
SOURCE DIRECT
PHONESSPEAKERS A/B
VOLUME
SOUND
MUTE
B.BOOST/BASS BOOST
MULTI CONTROL
MULTI CONTROL
1 “PHONO”2 “TUNER”3 “CD/DVD”4 “TAPE” or “MD”5 “VIDEO1”
if VIDEO2/MONITOR is VIDEO26 “VIDEO2”7 “DVD/6ch”8 “AV AUX”
else if VIDEO2/MONITOR is MONITOR6 “DVD/6ch”7 “AV AUX”
KRF-V6050D
*_4947/18-20/EN 3/15/01, 9:55 AM20
21
Oper
atio
ns
Muting the soundThe MUTE key lets you mute the sound of the speakers.
Press the MUTE key.
To cancelPress the MUTE key again so that the “MUTE” indicator goes off.
• MUTE ON can also be deactivated by turning the volume controlknob.
Blinks
SOURCE DIRECT playback (for analog input sources only)
Use this function to pass the source material direct to the amplifier,bypassing any audio processing.
To cancel
Press the SOURCE DIRECT key.
• When you press the LISTEN MODE, SOUND, or SET UP keys, orswitch to another input source, SOURCE DIRECT playback will becanceled.
• If CINEMA EQ. is switched ON, SOURCE DIRECT key will not beefffective.
Listening with headphones
1 (KRF-V6050D)Press the SPEAKERS A or B key so that the speaker indicatorgoes off.
(KRF-V5050D)Press the SPEAKER key so that the speaker indicator goes off.
Make sure the SPEAKERSindicators are turned off.
• If you turn off all of the speakers when in the surround mode, thesurround mode will be canceled as well, resulting in stereo play-back.
2 Connect the headphones to the PHONES jack.
3 Use the VOLUME CONTROL knob (VOLUME keys) to adjust thevolume.
1 Use the INPUT SELECTOR knob to select the source (other than“MD/TAPE”) you want to record.
2 Set the cassette deck or MD recorder to record.
3 Start playback, then start recording.
Recording audio (analog sources)
Recording
Recording a music source
1 Press the MONITOR key.
2 Use the INPUT SELECTOR knob to select a source other than“MD/TAPE”
3 Start playback on the cassette deck connected to the MONITORjacks and start recording on the cassette deck or MD recorderconnected to the MD/TAPE jacks.
Recording tapes or MD (with MONITOR function)
1 Use the INPUT SELECTOR knob to select “MD/TAPE”.
2 Start playback on the cassette deck connected to the MD/TAPEjacks and start recording on the cassette deck or MD recorderconnected to the VIDEO2/MONITOR jacks.
MONITOR = MD/TAPE recording
MD/TAPE = MONITOR recording
• To copy tapes using a double cassette deck, refer to the instructionmanual of the double cassette deck.
MONITOR function (analog sources only)You can connect a cassette deck or graphic equalizer to the VIDEO2/MONITOR jacks of the receiver. If a graphic equalizer is connected, theMONITOR key should be left in the on position. Alternately, if a cassettedeck equipped with a 3-head system is connected to the VIDEO2/MONITOR jacks, you will be able to monitor the just-recorded signalwhile making recordings on the cassette deck. By switching the MONI-TOR key on and off, you can compare the sound of the source signaland the just-recorded signal. For more information, refer to the instruc-tion manual of the connected component.
Press the SOURCE DIRECT key again.
• If SOURCE DIRECT playback was activated while in a surroundmode, canceling SOURCE DIRECT playback will reactivate the pre-vious surround mode.
Normal playback
LFE
C
S RSLS
TI.VOLBCLIPRDS EON PTYTP TA NEWS
SW
LSP A RMUTE
INPUT SELECTOR
MONITOR
S.DIRECTFMAMMHzkHz
PRO LOGIC3 DOWN MIX
DIGITAL
DSP
MEMOST.
TUNED
AUTO SOUND AUTO
STEREO MONITOR
Make sure the SP indicatorsare turned off.
KRF-V5050DKRF-V6050D
When recording a music source, switch the VIDEO2/MONITORsetting to “MONITOR”. 8
When recording a music source, switch the VIDEO2/MONITORsetting to “MONITOR”. 8
STEREO
FMAMMHzkHz
PRO LOGIC3 DOWN MIX
DIGITAL
MONITORDSP
MEMOST.
TUNED
AUTO SOUND AUTOS.DIRECT
SW
RLLFE
C
S RSLS
TI.VOLBCLIP MUTERDS EON PTYTP TA NEWS
SP A
SW
RLLFE
C
S RSLS
TI.VOLBCLIP MUTERDS EON PTYTP TA NEWS
ASP
PHONES
*_4947/21-26/EN 3/15/01, 9:56 AM21
22
Operations
1 Use the INPUT SELECTOR to select the source (CD, DVD, orVIDEO2) you want to record.
2 Set the cassette deck or MD to record.
3 Press and hold the DIMMER key for more than 2 seconds toselect the A-REC or M-REC mode.
1 Rec mode off : The digital input record mode isswitched off.
2 A-REC : The digital input signals (DTS, DolbyDigital, or PCM) are identified auto-matically and converted into stereosignals that are ready for recording.
3 M-REC : The input signal type at the momentthis mode is selected is held through-out this mode.
Recording audio (digital sources)Switch on the REC mode to record a digital input source.Usually use the A-REC (Auto-Record) mode to record audio inputsources. When the digital mode changes during recording in the A- RECmode, the audio input source may be interrupted momentarily.
4 Start playback, then start recording.
Recording
Recording video1 Use the INPUT SELECTOR to select the video source (other than
“VIDEO1”) you want to record.
2 Set the video deck connected to VIDEO 1 to record.• Select the REC MODE to record a digital input source.
3 Start playback, then start recording.• Recording may not be normal for some video software. This is due to
the copy guard condition. °
Recording music in A-REC or M-REC mode
INPUT SELECTOR
DIMMER
• If the audio reproduction stops in the middle due to change in theinput signals, etc., press the DIMMER key.
• The mode changes every 2 seconds as shown below.
For A-REC mode:
DIGITALAUTO SOUNDFMAMMHzkHz
3 DOWN MIX
S.DIRECTMONITOR
DSP
MEMOST.
TUNED
AUTOPRO LOGIC
DIGITALAUTO SOUNDFMAMMHzkHz
3 DOWN MIX
S.DIRECTMONITOR
DSP
MEMOST.
TUNED
AUTOPRO LOGIC
STEREO
STEREO
DIGITALAUTO SOUND
DIGITALAUTO SOUND
GITAL AUDIGITAL
GITAL AUTDIGITAL
For M-REC mode:FMAMMHzkHz
3 DOWN MIX
S.DIRECTMONITOR
DSP
MEMOST.
TUNED
AUTOPRO LOGIC
FMAMMHzkHz
3 DOWN MIX
S.DIRECTMONITOR
DSP
MEMOST.
TUNED
AUTOPRO LOGIC
STEREO
STEREO
DIGITALAUTO SOUNDAUTO SOUND
DIGITALAUTO SOUNDAUTO SOUND
*_4947/21-26/EN 3/15/01, 9:56 AM22
23
Oper
atio
ns
Listening to radio broadcasts
1
2
3
Each press switches the tuning method as follows:
4
Auto tuning : The next station is tuned automatically.Manual tuning : Turn the knob (or press the key) to select the
desired station.
Each press switches the bandas follows:
1 AUTO lit (auto tuning)2 AUTO not lit (manual tuning)
Frequencydisplay
“TUNED” is displayedwhen a station is received.
• Normally, set to “AUTO” (auto tuning). If the radio waves are weakand there is a lot of interference, switch to manual tuning. (Withmanual tuning, stereo broadcasts will be received in monaural.)
“AM” or “FM” appears in thedisplay.
Use the INPUT SELECTOR knob (TUNER key) to select thetuner.
Use the BAND key to select the desired broadcast band.
Use the AUTO/CINEMA EQ. key to select the desiredtuning method.
Use the MULTI CONTROL keys to select the station.
1 FM2 AM
“ST.” lights up when abroadcast is being received instereo.
AM
kHz
PRO LOGIC3 DOWN MIX
DIGITALS.DIRECTMONITOR
DSP
MEMOST.
TUNED
AUTO SOUNDFM
MHz STEREO
AUTO
AM
kHz
PRO LOGIC3 DOWN MIX
DIGITALS.DIRECTMONITOR
DSP
MEMOST.
TUNED
AUTO SOUNDFM
MHz STEREO
AUTO
AM
kHz
PRO LOGIC3 DOWN MIX
DIGITALS.DIRECTMONITOR
DSP
AUTO SOUNDMEMO
FM
MHz STEREO
AUTO
TUNEDST.
RDS is a system that transmits useful information (in the form of digitaldata) for FM broadcasts along with the broadcast signal. Tuners andreceivers designed for RDS reception can extract the information from thebroadcast signal for use with various functions, such as automatic displayof the station name.
RDS functions:PTY (Program Type Identification) Search §Automatically tunes to a station that is currently broadcasting thespecified program type (genre).
PS (Program Service Name) DisplayAutomatically displays the station name transmitted by the RDS station.
RDS AUTO MEMORY function ¢Automatically selects and stores up to 40 RDS stations in the presetmemory.If fewer than 40 RDS stations have been stored in the preset memory,regular FM stations will be stored in the remaining places.
Radio Text functionDisplays the radio text data transmitted by some RDS stations when youpress the RDS DISP. (Display) key. There is “NO RT” display if no textdata is transmitted.
Using RDS (Radio Data System)
The “RDS” indicator lights up when an RDS broadcast (signal) isreceived.
Before using a function utilizing the RDS, be sure to perform the RDSAuto Memory operation by referring to the description in “PresettingRDS stations (RDS AUTO MEMORY)”. ¢
NoteSome functions and function names may differ for certain countriesand areas.
MEMOAM
kHz
PRO LOGIC3 DOWN MIX
DIGITALS.DIRECTMONITOR
DSP
AUTO SOUND
LFE
C
S
TI.VOLBCLIP MUTE
EON PTYTP TA NEWS
FM
MHz STEREO
AUTO
TUNEDST.SW
RLSP A
RDS
Tuning (non-RDS) radio stations
Radio stations can be classified into RDS (Radio Data System) stationsand other stations. To listen to or store RDS stations in the preset memory,see the section entitled, “Using RDS”.
“AUTO” indicator lights up inthe display.
RC-R0616
MULTI CONTROL
INPUT SELECTOR
BAND AUTO/CINEMA EQ.
MULTI CONTROL
TUNER
AUTOBAND
RC-R0512
*_4947/21-26/EN 3/15/01, 9:56 AM23
24
Operations
Each press switches the display mode as follows:
1 PS (Program Service name) display2 RT (Radio Text) display3 Frequency display
Using the RDS DISP. (Display) key
1 PS (Program Service name) display:The station name is displayed automatically when an RDS broadcastis received,If no PS data was sent, “NO PS” is displayed.
Pressing the RDS DISP. key changes the contents of thedisplay.
2 RT (Radio Text) display:Text data accompanying the RDS broadcast scrolls across the dis-play. “NO RT” or “RT----” is displayed if the current RDS station doesnot provide RT data.
1
2
3
This function automatically stores up to 40 RDS stations in the presetmemory. In order to use the PTY function, the RDS stations must be storedin the preset memory using the RDS AUTO MEMORY function.
Use the INPUT SELECTOR knob to select the tuner.
Use the BAND key to set the broadcast band to “FM”.
Press and hold the MEMORY key for more than 2 seconds.
Presetting RDS stations (RDS AUTO MEMORY)
• After a few minutes, up to 40 RDS stations are preset in order fromchannel “01”.
• Stations already stored in the preset memory may be replaced byRDS stations. (i.e., If the RDS AUTO MEMORY function detects 15RDS stations, the stations currently preset at numbers 01~15 will bereplaced by the RDS stations.)
3 Frequency display:Displays the frequency of the current station.
Listening to radio broadcasts
MHzMEMOAM
kHz
PRO LOGIC3 DOWN MIX
DIGITALS.DIRECTMONITOR
DSP
AUTO SOUND
LFE
C
S
TI.VOLBCLIP MUTE
EON PTYTP TA NEWS
FM
STEREO
AUTO
TUNEDST.SW
RLSP A
RDS
MHzMEMOAM
kHz
PRO LOGIC3 DOWN MIX
DIGITALS.DIRECTMONITOR
DSP
AUTO SOUND
LFE
C
S
TI.VOLBCLIP MUTE
EON PTYTP TA NEWS
FM
STEREO
AUTO
TUNEDST.SW
RLSP A
RDS
MEMOAM
kHz
PRO LOGIC3 DOWN MIX
DIGITALS.DIRECTMONITOR
DSP
AUTO SOUND
LFE
C
S
TI.VOLBCLIP MUTE
EON PTYTP TA NEWS
FM
STEREO
AUTO
TUNEDST.SW
RLSP A
RDSMHz
INPUT SELECTOR
MEMORYAUTO/CINEMA EQ.
BAND
TUNEDST.
AUTO
AUTO
ST.TUNED
MHz
FM
FM
MHzRDS
RDS
MEMOAM
kHz
PRO LOGIC3 DOWN MIX
DIGITALS.DIRECTMONITOR
DSP
AUTO SOUND
LFE
C
S
TI.VOLBCLIP MUTE
EON PTYTP TA NEWS
STEREOSW
RLSP A
MEMOAM
kHz
PRO LOGIC3 DOWN MIX
DIGITALS.DIRECTMONITOR
DSP
AUTO SOUND
LFE
C
S
TI.VOLBCLIP MUTE
EON PTYTP TA NEWS
STEREOSW
RLSP A
RDS DISP.
RC-R0616 RC-R0512
*_4947/21-26/EN 3/15/01, 9:56 AM24
25
Oper
atio
ns
Presetting radio stations manually
• Repeat steps 1, 2, 3, and 4 to store as many stations as necessary.• If you store a station at a previously used preset, the old station will
be replaced by the new one.
Press the MEMORY key while receiving the station.
Proceed to step 3 within 5 seconds.(If more than 5 seconds elapse, press the MEMORY key again.)
Blinks for 5 seconds Lights for 5 seconds
1
2
Tune to the station you want to store.
3
4
Receiving preset stations
Enter the number of the preset you want to receive(up to “40”.)
1
2
Press the numeric keys in the following order:
For “15”, press .......... 0,5For “20”, press .......... 0,0,)
• If you make a mistake entering a two digit number, press the +10 keyseveral times to return to the original display and start again.
Use the MULTI CONTROL keys to select one of the stationpresets (1 – 40).
Press the MEMORY key to accept the setting.
Press TUNER key to select the tuner as the source.
AM
kHz
PRO LOGIC3 DOWN MIX
DIGITALS.DIRECTMONITOR
DSP
AUTO SOUND
LFE
C
S RSLS
TI.VOLBCLIP MUTERDS EON PTYTP TA NEWS
FM
MHz STEREO
AUTO
TUNEDST.
MEMOSW
RLSP A
AM
kHz
PRO LOGIC3 DOWN MIX
DIGITALS.DIRECTMONITOR
DSP
AUTO SOUND
LFE
C
S RSLS
TI.VOLBCLIP MUTERDS EON PTYTP TA NEWS
FM
MHz STEREO
AUTO
TUNEDST.SW
RLSP A
Listening to radio broadcasts
The RDS auto memory function assigns preset numbers to RDS stationsstarting from preset number "1". Therefore, be sure to execute the RDSauto memory function before using the following operations to manuallystore AM stations and other FM stations, and RDS stations.“Presetting RDS stations (RDS AUTO MEMORY)”. ¢
Receiving preset stations in order (P.CALL)
• Each time you press the key, another preset station is received inorder.
Pressing the P.CALL ¢ key does the following:=01=02=03= ... = ... 38=39=40
Pressing the P.CALL 4 key does the following: 01+02+03+ ... + ... 38+39+40+
Holding down the ¢ or 4 keys, lets you skip through thepresets, receiving each at preset station 0.5 second intervals.
1
2
Press TUNER key to select the tuner as the source.
Use the P.CALL 4/¢ keys to select the desiredstation.
TUNER
Numeric keys
RC-R0616 RC-R0512
RC-R0512RC-R0616
TUNER
P.CALL 4/¢
MULTI CONTROL
MEMORY
*_4947/21-26/EN 3/15/01, 9:56 AM25
26
Operations
Listening to radio broadcasts
1
2
When an RDS broadcast is received, the program type is shown on thedisplay. If no PTY data is available, or if the station is not an RDS station,“NONE” is displayed.
Program type table
Tuning by program type (PTY search)
This function lets you set the tuner to automatically search for stationswhich are currently broadcasting the type of program (genre) you want tolisten to.
Preparations• Execute the RDS auto memory procedure.• Set the broadcast band to FM.• Tune to an RDS station.
Program Type Name DisplayNews NEWSCurrent Affairs AFFAIRSInformation INFOSport SPORTEducation EDUCATEDrama DRAMACulture CULTUREScience SCIENCEVaried Speech VARIEDPop Music POP MRock Music ROCK MEasy Music EASY MLight Classical Music LIGHT MSerious Classical Music CLASSICSOther Music OTHER M
“NO PROG” is displayed if this operation is attempted beforeperforming the RDS Auto Memory operation.
Under certain receiving conditions, it may take more than 1minute to complete the search.
3 Press the PTY key to start searching.
EXAMPLE: Searching for a Rock Music broadcast.
Goes out
Station name display
Blinks
Program type name display
To select another program type
Display while searching.
Display when a station is received.
• No sound is heard while “PTY” is blinking.• If the desired program type cannot be found, “NO PROG” is dis-
played, then after several seconds the display returns to the originaldisplay.
Repeat steps 1, 2 and 3.
Press the PTY key to activate the PTY search mode.
While the “PTY” indicator is lit, use the MULTI CONTROLkeys or TUNING 1/ ¡ keys to select the program typeof your choice.
Program Type Name DisplayWeather WEATHERFinance FINANCEChildren’s Program CHILDRENSocial Affairs SOCIALReligion RELIGIONPhone In PHONE INTravel TRAVELLeisure LEISUREJazz Music JAZZCountry Music COUNTRYNational Music NATION MOldies Music OLDIESFolk Music FOLK MDocumentary DOCUMENT
AUTOMEMO
ST.TUNED
FM
MHz
NEWS
AM
kHz
PRO LOGIC3 DOWN MIX
DIGITALS.DIRECTMONITOR
DSP
AUTO SOUND
LFE
C
S RSLS
TI.VOLBCLIP MUTE
EONTP TA
STEREOSW
RLSP A
PTYRDS
AUTOMEMO
ST.TUNED
MHz
NEWS
AM
kHz
PRO LOGIC3 DOWN MIX
DIGITALS.DIRECTMONITOR
DSP
AUTO SOUND
LFE
C
S RSLS
TI.VOLBCLIP MUTE
EONTP TA
STEREOSW
RLSP A
PTYRDS
FM
PTY
AUTOMEMO
ST.TUNED
MHz
NEWS
AM
kHz
PRO LOGIC3 DOWN MIX
DIGITALS.DIRECTMONITOR
DSP
AUTO SOUND
LFE
C
S RSLS
TI.VOLBCLIP MUTE
EONTP TA
STEREOSW
RLSP A
RDS
FM
PTY
MULTICONTROL
RC-R0616 RC-R0512
TUNING1 / ¡
*_4947/21-26/EN 3/15/01, 9:56 AM26
27
Oper
atio
ns
Ambience effects
Manufactured under license from Dolby Laboratories. Dolby, Pro Logic andthe double-D symbol are trademarks of Dolby Laboratories. ConfidentialUnpublished Works. ©1992-1997 Dolby Laboratories. All rights reserved.
This receiver is equipped with listening modes that allowyou to enjoy an enhanced sonic ambience with a variety ofvideo sources.In order to obtain the optimum effect from the surroundmodes, make sure to input the proper speaker settingsbeforehand. *
Surround modes
Dolby DigitalThe Dolby Digital surround format lets you enjoy up to 5.1 channels ofdigital surround sound from Dolby Digital program sources (such as
Laserdisc or DVD software marked ). Compared with previousDolby surround, Dolby Digital provides even better sound quality,greater spatial accuracy, and improved dynamic range.
NoteAlthough a full set of speakers (front left, right, and center, surround leftand right, and a subwoofer) is required for true 5.1 channel Dolby Digitalsurround sound, this receiver lets you enjoy Dolby Digital (and DolbySurround) program sources, even if you connect only the front speakers.
* LFE = Low Frequency Effects. This channel delivers separate non-directional bass signals to the subwoofer for more dynamic deep basssound effects.Although only Dolby Digital soundtracks incorporate a separate lowfrequency channel, connecting a subwoofer will also improve deep bassperformance in the other surround modes.The indication “LFE” appears in the display when a signal is being inputfor this channel.
Front speaker (L, R)
Subwoofer (SW)*
Center speaker
Surround speakers (L, R)
DTSThe DTS multi-channel audio format is available on CD, LD and DVDsoftware. DTS is a strictly digital format and can not be decoded insidemost CD, LD or DVD players. For this reason, if you attempt to listen toDTS encoded software through the analog output of your new CD, LDor DVD player, you will experience digital noise in most cases. This noisecan be quite loud if the analog output is connected directly to a highpower amplification system. Proper measures for playing the digitaloutput as described below should be taken to avoid this situation. Toenjoy DTS Digital Surround playback, an external 5.1 channel DTSDigital Surround decoder system or an amplifier with a built-in DTSDigital Surround decoder must be connected to the digital output (S/PDIF, AES/EBU or TosLink) of a CD, LD or DVD player.All models are incorporated with the DTS decoder.
* Optional in this mode.
* LFE = Low Frequency Effects. This channel delivers separate non-directional bass signals to the subwoofer for more dynamic deepbass sound effects.DTS has a .1 or LFE channel.The indication “LFE” appears in the display when a signal is beinginput for this channel.
Front speaker (L, R)Subwoofer (SW)*
Center speaker
Surround speakers (L, R)
Dolby Pro Logic is a specially encoded 2 channel surround formatdesigned to provide theater-like surround sound from Dolby Surroundencoded sources (such as video and Laserdisc software marked
). This receiver is equipped with a Dolby Pro Logicsurround decoder to let you enjoy the wide variety of currently availableDolby Surround home video software. Surround signal is monaural.
Dolby Pro Logic
Manufactured under license from Digital TheaterSystems, Inc. US Pal. No. 5,451,942 and otherworldwide patents issues and pending.“DTS” and “DTS Digital Surround” are trademarks ofDigital Theater Systems, Inc.© 1996 Digital Theater Systems, Inc. All rights re-served.
Front speaker (L, R)
Subwoofer (SW)
Center speaker
Surround speakers (L, R)
*_4947/27-40/EN 3/15/01, 9:57 AM27
28
Operations
Ambience effects
Center speaker
Dolby 3 StereoDolby 3 Stereo is available for systems that do not have surroundspeakers. When in the Dolby 3 Stereo mode, the surround informationis redirected to the front left and right speakers. This mode is designedfor use with Dolby Surround program sources, but can also improvesound field unity for programs that are not Dolby Surround encoded.Dialog positioning and sound image definition, however, may not be asaccurate when used with programs that are not Dolby Surroundencoded.
DVD 6-channel modeUsing a DVD player or the like equipped with six (5.1) output channelsand the receiver, you can enjoy multi-channel encoded DVD sourcematerial in all its splendor. Since the source signals are digital and eachchannel is input independently, the resulting sound quality, sense ofspaciousness, and dynamic range are superb.
Center speaker
DSP modeThe DSP mode lets you add the atmosphere of a live concert or hall toalmost any type of program source. These modes are particularlyeffective when used with stereo program sources, like CD, television,and FM radio. You might enjoy trying the ARENA, JAZZ CLUB, THEATER,STADIUM or DISCO mode the next time you watch a concert or sportingevent!
What's DSP?DSP stands for Digital Signal Processor.The way a sound is heard in an actual environment depends on a varietyof different factors. One of the most important is reverberation (the actof decaying elements of sound echoing in various places).The DSP modes produce the feeling of presence by using the DSP tocreate reverberation, without spoiling the sound quality of the originalsignal.
Center speaker
* LFE = Low Frequency Effects. This channel delivers separate non-directional bass signals to the subwoofer for more dynamic deepbass sound effects.
Front speaker (L, R)
Subwoofer (SW)
Surround speakers (L, R)Front speaker (L, R)
Subwoofer (SW)
Front speaker (L, R)
Subwoofer (SW)
Surround speaker (L, R)
*_4947/27-40/EN 3/15/01, 9:57 AM28
29
Oper
atio
ns
Ambience effects
When the DTS signal is input:(The DTS indicator lights up.)
1 DTS: DTS surround2 STEREO: Normal stereo playback
When the analog or digital signal (except for the DOLBYDIGITAL or DTS signal) is input:
1 PRO LOGIC: PRO LOGIC surround (The PRO LOGICindicator lights up).
2 3 STEREO: 3-STEREO surround (The 3 STEREO indi-cator lights up.)
3 ARENA: DSP surround.4 JAZZ CLUB: DSP surround.5 THEATER: DSP surround.6 STADIUM: DSP surround.7 DISCO: DSP surround.8 STEREO: Normal stereo playback. Sound is produced
from the two front channels only.
Adjust the volume.
3
• If a Dolby Digital signal having more channels than the maximumnumber of playback channels available using the receiver’s currentsettings is input, the DOWNMIX indicator on the front panel lightsup and downmixing is performed to match the number of availablechannels.
Notes• Depending on the type of the signal or speaker setting, some listening
modes cannot be selected.• When playback is started, the sound may be cut or interrupted before
the input source is confirmed as Dolby Digital.• To enjoy Dolby Digital surround (as well as all the other listening
modes) from a single component, be sure to use a Dolby Digitalcompatible source component. Connect the Dolby Digital compatiblesource component's Dolby Digital format digital audio signal to one ofthe DIGITAL INPUT jacks on the back of the receiver. Connect thenormal audio signal correctly to the respective component's AUDIOjacks. 90!@
Surround Play
The DTS compatible models can reproduce a CD, DVD, or LD carrying
the DTS mark.
DOLBY DIGITAL can be used when playing DVD or LD software bearing the
mark and DOLBY DIGITAL format digital broadcasts (etc.).
DOLBY PRO LOGIC and DOLBY 3 STEREO can be used when playing
video, DVD, or LD software bearing the mark.
• Turn ON related components.• Complete “Preparing for surround sound” (speaker settings).*• Use the INPUT SELECTOR to select the component you wish to
play back with surround sound.• Use the INPUT MODE key to select the input mode (analog or digital)
for the source you wish to play back. 8• Noise will be produced when a DTS source is played by selecting the
analog input.
Preparations
Start playing the video software.
Press the LISTEN MODE (LSTN M.) key to select thelistening mode.The listening mode settings are stored separately for each input. If theinput mode is set to digital auto (“AUTO SOUND” lights), the receiverselects the optimal listening mode automatically based on the type ofinput signal and the speaker settings.
Each press of the LISTEN MODE (LSTN M.) key switches thesetting as listed below.The listening mode settings are different depending on thetype of input signal.
When the DOLBY DIGITAL signal is input:1 DOLBY DIGITAL: DOLBY DIGITAL surround (The
DOLBY DIGITAL indicator lights up.)2 PRO LOGIC: PRO LOGIC surround (The PRO LOGIC
indicator lights up.)3 3 STEREO: 3-STEREO surround (The 3 STEREO
indicator lights up.)4 STEREO: Normal stereo playback
When you select DOLBY DIGITAL
1
2
STEREO
FMAMMHzkHz
PRO LOGIC3 DOWN MIX
S.DIRECTMONITOR
DSP
MEMOST.
TUNED
AUTO
S
TI.VOLBCLIP MUTERDS EON PTYTP TA NEWS
SP A RCL
SRSL
AUTO SOUND DIGITAL
LFE
INPUTSELECTOR
INPUT SELECTORINPUT MODE
LISTEN MODE
LSTN M.LISTEN MODE
RC-R0616 RC-R0512
*_4947/27-40/EN 3/15/01, 9:57 AM29
30
Operations
Ambience effects
Convenient functions
Adjusting the soundYou can make further adjustments to the sound while listening to playbackin the surround mode.
1 Press the SOUND key repeatedly until the desired item appearsin the display.
Each time you press the button, the menu changes as follows:Note that some items are not displayed in certain modes.
1 BASS (low frequency range sound quality adjustment) )2 TREB (high frequency range sound quality adjustment) )3 C (center speaker level adjustment)4 SR (right surround speaker level adjustment)5 SL (left surround speaker level adjustment)6 SW (subwoofer level adjustment)7 INPUT (input level adjustment) (8 NIGHT (midnight mode on/off-Dolby Digital mode only)
2 Use the MULTI CONTROL keys to adjust the setting as desired. • The adjustment item is displayed for approximately 8 seconds.
Midnight mode (Dolby Digital mode only)When watching movies at night , you might not be able to raise the volumeas loud as normal. Midnight mode compresses the dynamic range ofpreviously specified parts of the Dolby Digital sound track (like sceneswith sudden increases in volume) to minimize the difference in volumebetween the specified and non-specified parts. This makes it easy to hearall of the sound track, even when listening at low volumes.
1 Press the SOUND key repeatedly until “NIGHT” appears on thedisplay.• This can be selected only if DVD or VIDEO2 is selected as the source
and the listen mode is set to “DOLBY DIGITAL.”
1
DVD 6-channel playbackUsing a DVD player or the like equipped with six (5.1) output channels andthe receiver, you can enjoy surround sound playback.When you try to play a disc other than Dolby Digital such as DTS CD, nosound is produced or, noise may be heard. To avoid this situation, makesure that you connect the component to the receiver’s DVD/6ch. INPUTjacks through a surround processor which can decode the surroundsignal you wont to listen to.Connecting a DVD player which can decode the surround signal itself isalso acceptable.
Preparations
Select “DVD/6ch” as the input source.• If speaker system B is on when “DVD/6ch” is selected as the input
source, it switches off and speaker system A turns on automatically.
Start playback of the DVD software.
Adjust the volume.
• It is not possible to adjust the volume level or sound quality (SET UP,SOUND) of the channels separatedly when the receiver is in the DVD/6ch mode. Adjust the volume with the controls of the DVD player.For the powered subwoofer, you can adjust the volume of thesubwoofer using the subwoofer’s own volume control.
• Connect your DVD player to the DVD/6ch jacks of the receiver.• Turn on all other components that will be used.• Complete “Preparing for surround sound”. *
3
4
Select "6ch INPT" by pressing the INPUT MODE key.2
RC-R0512RC-R0616
MULTI CONTROL
DIMMER
SOUND
SOUND
MULTI CONTROL
RC-R0512
INPUT SELECTOR
DVD
INPUT MODE
RC-R0616
*_4947/27-40/EN 3/15/01, 9:57 AM30
31
Oper
atio
ns
• The adjustment item is displayed for approximately 8 seconds.• Some Dolby Digital software may not be compatible with the Midnight
mode.
2 Use the MULTI CONTROL keys to select the ON or OFF setting.
Ambience effects
STEREO
FMAMMHzkHz
PRO LOGIC3 DOWN MIX
S.DIRECTMONITOR
DSP
MEMOST.
TUNED
AUTO
S
TI.VOLBCLIP MUTERDS EON PTYTP TA NEWS
SP A RCL
RSLS
DIGITALAUTO SOUND
LFE
Display dimmer adjustmentThe dimmer function lets you select the brightness of the receiver'sdisplay. You might find this useful if you darken your room to watch moviesor listen to music.
Each time you press the DIMMER key, the display brightnesschanges among the three available settings. Select the bright-ness level you find most pleasing.
96kHz LPCM playback
The receiver is compatible with the 96kHz LPCM playback. To play a96kHz DVD, set the listen mode to “STEREO”.
• When “96kHz” appears in the display, press the LISTEN MODE key(the listen mode changes to the STEREO mode).
LFE
DIGITALAUTO SOUND
STEREO
FMAMMHzkHz
3 DOWN MIX
S.DIRECTMONITOR
DSP
MEMOST.
TUNED
AUTOTI.VOLBCLIP MUTERDS EON PTYTP TA NEWS
SW
SP A RCL PRO LOGIC
S
LFE
DIGITALAUTO SOUND
STEREO
FMAMMHzkHz
3 DOWN MIX
S.DIRECTMONITOR
DSP
MEMOST.
TUNED
AUTOTI.VOLBCLIP MUTERDS EON PTYTP TA NEWS
SW
SP A RCL PRO LOGIC
S
LFE
DIGITALAUTO SOUND
STEREO
FMAMMHzkHz
3 DOWN MIX
S.DIRECTMONITOR
DSP
MEMOST.
TUNED
AUTOTI.VOLBCLIP MUTERDS EON PTYTP TA NEWS
SW
SP A RCL
SL
PRO LOGIC
S
*_4947/27-40/EN 3/15/01, 9:57 AM31
32
Remote Control
Input Component Maker Code Key
(DVD) DVD player KENWOOD 805,808 DVD
The remote control supplied with this receiver (for KRF-V6050D only) isalso capable of controlling components from a variety of manufacturersonce you register the appropriate setup codes into the remote controlunit.
1
Registering setup codes for other components
Find the setup code of the component to be registered.
Basic remote control operations for other components
• Refer to the setup code lists to find the setup code for the componentto be registered. ‹Example: To register a DVD made by KENWOOD, you would enter“805”.
2 Hold down the POWER key and press the numeric keys toenter the setup code.
Low battery warningReplace all four batteries with new ones when you notice a shorteningof the distance from which the remote control will operate. The remotecontrol is designed to retain setup codes in memory while you changebatteries.
Press the source POWER (TV, VCR, DVD) key for morethan 2 seconds, and check to see that the component youwant to control turns on.
• Example: Press “805” to register a DVD player made by KENWOOD.• If you push an invalid key, the remote will exit the setup mode.
If the component does not react, and there is more than onesetup code, enter another setup code and try again.
• 6, TUNING 1/¡, or MULTI CONTROL key(s) can also beused instead of the POWER key.
• If the component is already on, pressing the source POWER keyswill turn it off.
3
Repeat steps 2 to 3 to register additional componentsuntil all components have been registered.
4
NoteAlthough each setup code is designed to work with a number of differentmodels, certain codes may not work with some models. (Also, certaincodes may only operate some of the functions available on a givenmodel.)
This operation lets you operate the registered components.KENWOOD audio components with system control turn on and offautomatically with the receiver via the system control connections.
Operating other components
Use the input selector keys to select the component youdesire.
NoteBe sure to point the remote control at the remote sensor on the receiverwhen you want to operate KENWOOD components connected bysystem control cords. Otherwise, point the remote control at the compo-nent you want to operate.
The remote control mode returns to the receiver operation modewhen you do not operate for more than 15 seconds.
1
2
3 Press the operation keys you desire. fl
• Pressing the input selector keys also changes the input selector onthe receiver.
• When you operate your registered TV, VCR, or DVD player, goto step 2.
• When you operate the CD player, Cassette deck, MD player, orTuner with system control connection, go to step 3.
• To return to the receiver operation mode, press the RECEIVER key.
Press the source POWER key.
POWER
Source POWERkey
Numeric keysPOWER
RECEIVER
Source POWERkeys
(For KRF-V6050D)
*_4947/27-40/EN 3/15/01, 9:57 AM32
33
Rem
ote
Cont
rol
Maker Setup codes
BLAUPANKT 401GRUNDIG 402MIVER 401NOKIA 403NORDMENDE 404, 405PHILIPS 406SABA 404, 407SCHNEIDER 408TELEFUNKEN 407, 409, 410THOMSON 411AKAI 408FENNER 412FISHER 413HITACHI 414, 415INNO-HIT 416IRRADIO 408JVC 417MAGNAVOX 406OKANO 416ORION 418PANASONIC 419, 420SAMSUNG 421SANYO 413SHARP 422SONY 423, 424, 425,
426, 427TOSHIBA 428LOEWE 429, 430
TV Setup codes
Maker Setup codes
BLAUPANKT 501GRUNDIG 502LOEWE 503, 504NOKIA 505NORDMENDE 506, 507, 508PHILIPS 509SABA 510SIEMENS 502TELEFUNKEN 511, 512AIWA 513BELL+HOWELL 514CGM 514, 515DIGTAL 515FISHER 514G.E. 516HITACHI 517, 518JVC 519MAGNAVOX 501, 515MITSUBISHI 520, 521, 522,
523PANASONIC 524PHONOLA 515SAMSUNG 525, 526SANYO 514SHARP 527, 528SONY 529, 530, 531TOSHIBA 532
VCR Setup codes
Maker Setup codes
JVC 801SONY 802PIONEER 803PANASONIC 804KENWOOD 805, 808TOSHIBA 806PHILIPS 807
DVD Setup codes
Basic remote control operations for other components
Setup code chart (For KRF-V6050D (RC-R0616))
*_4947/27-40/EN 3/15/01, 9:58 AM33
34
Remote Control
Basic remote control operations for other components
The remote control of this unit can control two groups of KENWOOD DVD players directly without using theremote control supplied with the DVD player.
Group-1: DV-4900, DV-4070B, DV-2070, DV-203, DVF-9010, DVF-K7010, DVF-5010, DVF-R9030, DVF-R7030, DVF-3530 and DV-402
Group-2: DV-4050, DV-303, DVF-R6030, DVF-K5020, DVF-5020, DVF-3020 and DVF-3030
Depending on your KENWOOD DVD model, you need to set up your receiver remote control as follows:To set for Group-1 DVD players:
Press the numeric "1" key while pressing the "POWER" key (not the DVD Power key) on your remotecontrol.
To set for Group-2 DVD players:Press the numeric "2" key while pressing the "POWER" key (not the DVD Power key) on your remotecontrol.
• If your DVD player is not listed in the list above, perform the set up for either Group-1 or Group-2.When the set up is successful, then your DVD player falls into that particular group.
How to operate the DVD player with the remote control1. Pressing the DVD Power key for more than 2 seconds turns the DVD player on or off.2. To carry out the functions of the DVD player, first press the DVD Power key, then press each key
for each operation as explained in the DVD operation pages in the operating instructions. In this case,the DVD operation mode is retained for 15 seconds after pressing any of those DVD operationbuttons.(To turn the receiver operation mode within 15 seconds, press the RECEIVER key.)
DVD player operation keysYou can perform these basic operations using the keys described below when connected to KENWOOD DVDplayer.
DVD player operations (For KRF-V5050D)
1
DISC SKIP
DISC SEL.CINE.EQ
BASS BOOSTAUTO
PHONO CD/DVD TUNER MD/TAPE
VIDEO1 VIDEO2
2 3
POWER
DVD
POWER
RECEIVER
MENU
P.CALL
TUNING
MUTE VOLUME
A/B+100DVD
ENTER BAND
P.CALL
MULTI CONTROL
4 5 6
7 8 9
0 +10
SET UPOSD
SOUNDRETURN TITLE
LISTEN MODE
RDS DISP.
PTY
DVD
6 (3 Play)7 (Stop)
¢ (Skip up)
8 (Pause)
4 (Skip down)
1 (Search)¡ (Search)
Numeric keys(Select tracks)
ENTER (Enter)
RETURN (Return)TITLE (Title)
RECEIVER(Receiver mode)
DVD POWER
% (Cursor »)fi (Cursor «)
@ (Cursor |)# (Cursor \)
MENU (Menu)OSD (OSD menu)
RC-R0512
*_4947/27-40/EN 3/15/01, 9:58 AM34
35
Rem
ote
Cont
rol
Basic remote control operations for other components
1
DISC SKIP
DISC SEL.CINE.EQ
BASS BOOSTAUTO
PHONO CD/DVD TUNER MD/TAPE
VIDEO1 VIDEO2
2 3
POWER
DVD
POWER
RECEIVER
MENU
P.CALL
TUNING
MUTE
VOLUME
A/B+100DVD
ENTER BAND
P.CALL
MULTI CONTROL
4 5 6
7 8 9
0 +10
SET UPOSD
SOUNDRETURN TITLE
LISTEN MODE
RDS DISP.
PTY
DVD
1
DISC SKIP
DISC SEL.CINE.EQ
BASS BOOSTAUTO
PHONO CD/DVD TUNER MD/TAPE
VIDEO1 VIDEO2
2 3
POWER
DVD
POWER
RECEIVER
MENU
P.CALL
TUNING
MUTE VOLUME
A/B+100DVD
ENTER BAND
P.CALL
MULTI CONTROL
4 5 6
7 8 9
0 +10
SET UPOSD
SOUNDRETURN TITLE
LISTEN MODE
RDS DISP.
PTY
DVD
1
DISC SKIP
DISC SEL.CINE.EQ
BASS BOOSTAUTO
PHONO CD/DVD TUNER MD/TAPE
VIDEO1 VIDEO2
2 3
POWER
DVD
POWER
RECEIVER
MENU
P.CALL
TUNING
MUTE VOLUME
A/B+100DVD
ENTER BAND
P.CALL
MULTI CONTROL
4 5 6
7 8 9
0 +10
SET UPOSD
SOUNDRETURN TITLE
LISTEN MODE
RDS DISP.
PTY
DVD
MD recorder operations
RC-R0512RC-R0512
RC-R0512
CD player operations
CASSETTE deck, CD player & MD recorder operations (For KRF-V5050D)
Notes1. Certain codes may only operate some of the function available on a given model.2. The charts above show the typical functions available for each component. Some manufacturers use different key combinations to perform similar
functions. For that reason, we have programmed extra functions on some of the unused number keys to help you control your equipment.
Cassette deck operations
6 (3 Play)
7 (Stop)
¢ (Skip up)4 (Skip down)
¡ (Search)
Numeric keys(Select tracks)
+100 (Select tracks)
6 (3 Play)7 (Stop)
1 (Rewind)¡ (Fast forward)
2 (Play)
1 (Search)
6 (Play/Pause)7 (Stop)
¢ (Skip up)4 (Skip down)
¡ (Search)
Numeric keys(Select tracks)
1 (Search)
DISC SKIP(Disc skip)
You can perform these basic operations using the keys described below when connected to KENWOOD cassettedeck, MD recorder or CD player equipped with system control operations. %
*_4947/27-40/EN 3/15/01, 9:58 AM35
36
Remote Control
Basic remote control operations for other components
Cassette deck operations
RC-R0616
You can perform these basic operations using the keys described below when connected to KENWOOD cassettedeck, MD recorder or CD player equipped with system control operations. %
CASSETTE deck, CD player & MD recorder operations (For KRF-V6050D)
1
B.BOOST DISC SKIP DVD
PHONO CD/DVD TUNER MD/TAPE
VIDEO1 VIDEO2 CINE.EQ AV AUX
2 3
POWER
RDS DISP.PTY
RETURN
OSDMENU
P.CALL
TUNING
MUTE VOLUME
A/B+100
TITLE TV SEL.RECEIVER
AUTO
INPUT SEL.
DISC SEL. CHANNEL
ENTER BAND
P.CALL
MULTI CONTROL
4 5 6
7 8 9
0 +10 LSTN M.
SET UP SOUND
POWER
TV
DVD
VCR
DVD
1 (Rewind)¡ (Fast forward) 6 (3 Play)
7 (Stop)
CD player operations
RC-R0616
1
B.BOOST DISC SKIP DVD
PHONO CD/DVD TUNER MD/TAPE
VIDEO1 VIDEO2 CINE.EQ AV AUX
2 3
POWER
RDS DISP.PTY
RETURN
OSDMENU
P.CALL
TUNING
MUTE VOLUME
A/B+100
TITLE TV SEL.RECEIVER
AUTO
INPUT SEL.
DISC SEL. CHANNEL
ENTER BAND
P.CALL
MULTI CONTROL
4 5 6
7 8 9
0 +10 LSTN M.
SET UP SOUND
POWER
TV
DVD
VCR
DVD
4 (Skip down)
Numeric keys(Select tracks)
6 (Play/Pause)7 (Stop)
¢ (Skip up)
1 (Search)¡ (Search)
DISC SKIP(Disc skip)
MD recorder operations
RC-R0616
1
B.BOOST DISC SKIP DVD
PHONO CD/DVD TUNER MD/TAPE
VIDEO1 VIDEO2 AV AUX
2 3
POWER
RDS DISP.PTY
RETURN
OSDMENU
P.CALL
TUNING
MUTE VOLUME
A/B+100
TITLE TV SEL.RECEIVER
AUTO
INPUT SEL.
DISC SEL. CHANNEL
ENTER BAND
P.CALL
MULTI CONTROL
4 5 6
7 8 9
0 +10 LSTN M.
SET UP SOUND
CINE.EQ
POWER
TV
DVD
VCR
DVD
6 (3 Play)7 (Stop)
¢ (Skip up)4 (Skip down)
1 (Search)¡ (Search)
Numeric keys(Select tracks)
+100 (Select tracks)
2 (Play)
*_4947/27-40/EN 3/15/01, 9:58 AM36
37
Rem
ote
Cont
rol
Basic remote control operations for other components
TV operations
RC-R0616
Other components' operations (For KRF-V6050D)
These keys can be used to perform the basic operations of KENWOOD and other makers'components which the setup code for each component had been entered beforehand.
‹
Refer to the following for the type of remote control operations available for each component.
• When pressing keys in succession, press each key firmly and be sure towait at least 1 second before pressing the next key.
• Numeric keys function the same as the numeric keys on the originalremote.
1
B.BOOST DISC SKIP DVD
PHONO CD/DVD TUNER MD/TAPE
VIDEO1 VIDEO2 CINE.EQ AV AUX
2 3
POWER
RDS DISP.PTY
RETURN
OSDMENU
P.CALL
TUNING
MUTE VOLUME
A/B+100
TITLE TV SEL.RECEIVER
AUTO
INPUT SEL.
DISC SEL. CHANNEL
ENTER BAND
P.CALL
MULTI CONTROL
4 5 6
7 8 9
0 +10 LSTN M.
SET UP SOUND
POWER
TV
DVD
VCR
DVD
Numeric keys
MUTE (Mute) VOLUME %/fi(Volume +/-)
ENTER (Enter)
TV SEL.(TV Selector)
CHANNEL %/fi(Channel +/-)
INPUT SEL.(Input selector)
VCR operations
RC-R0616
1
B.BOOST DISC SKIP DVD
PHONO CD/DVD TUNER MD/TAPE
VIDEO1 VIDEO2 CINE.EQ AV AUX
2 3
POWER
RDS DISP.PTY
RETURN
OSDMENU
P.CALL
TUNING
MUTE VOLUME
A/B+100
TITLE TV SEL.RECEIVER
AUTO
INPUT SEL.
DISC SEL. CHANNEL
ENTER BAND
P.CALL
MULTI CONTROL
4 5 6
7 8 9
0 +10 LSTN M.
SET UP SOUND
POWER
TV
DVD
VCR
DVD
1 (Rewind)6 (3 Play)7 (Stop)8 (Pause)
DVD player operations
RC-R0616
1
B.BOOST DISC SKIP DVD
PHONO CD/DVD TUNER MD/TAPE
VIDEO1 VIDEO2 CINE.EQ AV AUX
2 3
POWER
RDS DISP.PTY
RETURN
OSDMENU
P.CALL
TUNING
MUTE VOLUME
A/B+100
TITLE TV SEL.RECEIVER
AUTO
INPUT SEL.
DISC SEL. CHANNEL
ENTER BAND
P.CALL
MULTI CONTROL
4 5 6
7 8 9
0 +10 LSTN M.
SET UP SOUND
POWER
TV
DVD
VCR
DVD
6 (3 Play)7 (Stop)
¢ (Skip up)
8 (Pause)
4 (Skip down)
1 (Search)¡ (Search)
Numeric keys(Select tracks)
RETURN (Return)
TITLE (Title)
% (Cursor »)fi (Cursor «)
@ (Cursor |)# (Cursor \)
MENU (Menu)OSD (OSD menu)
1 Select the input source.
2 Press the keys corresponding to the operations you desire.Refer to the following sections for details.
¡ (Fast forward)
*_4947/27-40/EN 3/15/01, 9:58 AM37
38
Additional Information
Resetting the MicrocomputerThe microcomputer may malfunction (unit cannot be operated,or shows an erroneous display) if the power cord isunplugged while the power is ON, or due to some otherexternal factors. If this happens, execute the followingprocedure to reset the microcomputer and return the unit toits normal operating condition.
In case of difficulty
Amplifier
Cause
• The speaker cords are disconnected.
• VOLUME is set to the minimum position.• MUTE is ON.• The SPEAKERS switches are set to OFF.
• Speaker cords are short-circuited.
• The speaker cord is disconnected.
• The surround speaker cords and/or the centerspeaker cord is disconnected.
• A surround mode has not been engaged.• The surround and/or center volume controls are
set to the minimum level.
• The audio cord from the turntable is not con-nected to the PHONO jacks.
• The turntable is not grounded.
• There are many possible causes for this prob-lem, depending on the type of DVD player used.
• The input mode is set to digital manual.
• The software is copy-guarded.
Remedy
• Connect them properly referring to “Connectingthe speakers” %
• Adjust the volume to a proper level.• Turn OFF the MUTE. ¡• Set the SPEAKERS switch(es) to ON. (
• Turn the power off, eliminate the short-circuit-ing, then turn on the power again.
• Connect it properly referring to “Connecting thespeakers”. %
• Connect it properly referring to “Connecting thespeakers”. %
• Select a surround mode.• Adjust the speaker levels using the test tone.
*
• Insert the audio cord plugs securely into thePHONO jacks.
• Connect the grounding wire to the GND termi-nal on the rear panel.
• Set the input mode to digital manual beforestarting playback of the Dolby Digital source.
8
• Press the INPUT MODE key to select to digitalauto mode. 8
• Copy-guarded video software cannot be re-corded.
TunerCause
• No antenna is connected.• The broadcast band is not set properly.• The frequency of the desired station is not
tuned.
• Noise due to ignition noise from an automobile.• Noise due to interference from an electric appli-
ance.• Noise due to a nearby TV set.
• The preset station belongs to a frequency thatcannot be received.
• The preset memory was cleared because thepower cord had been unplugged for a longperiod of time.
Remedy
• Connect an antenna. #• Set the broadcast band properly.• Tune the frequency of the desired station.
£
• Install the outdoor antenna away from the road.• Turn off the power to the appliance.
• Install the receiver farther away from the TV.
• Preset a station with a receivable frequency.
• Preset the station again.
Symptom
Radio stations cannot be received.
Interference.
A station which was preset cannot be re-ceived by pressing the corresponding nu-meric key.
Symptom
No sound from the speakers.
The standby indicator blinks and sound isnot output.
Sound is not output from one of the speakers.
Sound is not output from the surroundspeakers and / or the center speaker, or theirsound is very small.
A humming noise is generated when thePHONO input selector is selected.
When playing a Dolby Digital source signalusing a DVD player, the sound is cut off soonafter it starts.
No sound is produced during playback froma DVD player.
A video source cannot be recordednormally.
With the power cord plugged in, turn the POWER keyOFF. Then, while holding down the ON/STANDBY key,press POWER key.
• Please note that resetting the microcomputer will clear the contents ofthe memory and returns the unit to the state it was in when it left thefactory.
*_4947/27-40/EN 3/15/01, 9:58 AM38
39
Addi
tiona
l Inf
orm
atio
n
Remote control unit
Cause
• No setup codes registered at for the respectiveinput(s).
• The remote control is set to a different operationmode.
• Batteries are exhausted.• The remote control unit is too far away from the
main system, controlling angle is too large, orthere is an obstacle between the receiver andthe remote.
• The audio cords and system control cords arenot connected properly.
• No software is loaded in the source component.
• An attempt is made to play a tape which is beingrecorded in the cassette deck.
• The remote control has not been set to theoperation mode for the component you wish tocontrol.
• The microprocessor of the remote control mal-functions.
Remedy
• Register a setup code at the respective input(s).‹
• Press the source select keys or source POWERkeys to select the appropriate operation mode.
• Replace with new batteries.• Operate the remote control unit within the con-
trollable range.
• Connect properly referring to “Setting up thesystem”.
• Place software in the source component youwant to play.
• Wait until recording has completed.
• Press the source select keys or source POWERkeys to activate the operation mode for thecomponent you want to control before opera-tion. ¤
• Reset the microprocessor.
Symptom
Certain inputs cannot be selected using theremote control.
Remote control operation is not possible.
In case of difficulty
*_4947/27-40/EN 3/15/01, 9:58 AM39
Specifications Caution : Read this page carefully to ensure safeoperation.
AUDIO section (KRF-V6050D)Rated power output during STEREO operation
DIN/IEC (DIN 1kHz, 0.7% T.H.D.,at 6 Ω) ............ 110 W + 110 WEffective power output during SURROUND operation
FRONT (1kHz, 0.7% T.H.D. at 6 Ω, one channel driven).............................................................................. 100 W + 100 W
CENTER (1kHz, 0.7% T.H.D. at 6 Ω, one channel driven)............................................................................................. 100 W
SURROUND (1kHz, 0.7% T.H.D. at 6 Ω, one channel driven).............................................................................. 100 W + 100 W
Total harmonic distortion ......................... 0.050% (1 kHz, 50W, 6 Ω)Frequency response (IHF '66)
CD ............................................. 10 Hz ~ 60 kHz, +0 dB, –3.0 dBSignal to noise ratio (IHF’66)
PHONO (MM) ........................................................................ 74 dBCD ......................................................................................... 90 dB
Input sensitivity / impedancePHONO (MM) ......................................................... 2.5 mV / 27 kΩCD ......................................................................... 200 mV / 47 kΩVIDEO2/MONITOR ............................................... 200 mV / 47 kΩDVD/6ch INPUT ................................................... 200 mV / 10 kΩ
Output level / impedanceTAPE REC .............................................................. 200 mV / 1 kΩVIDEO2/MONITOR ................................................. 200 mV / 1 kΩPRE OUT (SUBWOOFER) ...................................... 1.5 V / 2.2 kΩ
Tone controlBASS ................................................................ ±10 dB (at 70 Hz)TREBLE .......................................................... ±10 dB (at 10 kHz)
AUDIO section (KRF-V5050D)Rated power output during STEREO operation
DIN/IEC (DIN 1 kHz, 0.7% T.H.D., 6 Ω) ............... 110 W + 110 WEffective power output during SURROUND operation
FRONT (1kHz, 0.7% T.H.D. at 6 Ω, one channel driven).............................................................................. 100 W + 100 W
CENTER (1kHz, 0.7% T.H.D. at 6 Ω, one channel driven)............................................................................................. 100 W
SURROUND (1kHz, 0.7% T.H.D. at 6 Ω, one channel driven).............................................................................. 100 W + 100 W
Total harmonic distortion ......................... 0.050% (1 kHz, 50W, 6 Ω)Frequency response (IHF '66)
CD ............................................. 40 Hz ~ 60 kHz, +0 dB, –3.0 dBSignal to noise ratio (IHF’66)
PHONO (MM) ........................................................................ 74 dBCD ......................................................................................... 90 dB
Input sensitivity / impedancePHONO (MM) ......................................................... 2.5 mV / 27 kΩCD ......................................................................... 200 mV / 47 kΩMONITOR IN (VIDEO2/MONITOR) ..................... 200 mV / 47 kΩDVD/6ch INPUT ................................................... 200 mV / 47 kΩ
Output level / impedanceTAPE REC .............................................................. 200 mV / 1 kΩMONITOR OUT (VIDEO2/MONITOR) ................... 200 mV / 1 kΩPRE OUT (SUBWOOFER) ...................................... 1.5 V / 2.2 kΩ
Tone controlBASS ................................................................ ±10 dB (at 70 Hz)TREBLE .......................................................... ±10 dB (at 10 kHz)
DIGITAL AUDIO sectionSampling frequency ...................... 32 kHz, 44.1 kHz, 48 kHz, 96kHzInput level / impedance / wave length
Optical ........................... (–15 dBm ~ –21 dBm), 660 nm ±30nmCoaxial ................................................................. 0.5 Vp-p / 75 Ω
VIDEO sectionVIDEO inputs / outputs
VIDEO (composite) ................................................. 1 Vp-p / 75 ΩS-VIDEO inputs / outputs (KRF-V6050D)
S-VIDEO (luminance signal) .................................. 1 Vp-p / 75 Ω(chrominance signal) ...................... 0.286 Vp-p / 75 Ω
FM tuner sectionTuning frequency range ................................... 87.5 MHz ~ 108 MHzUsable sensitivity (DIN at 75 Ω)
MONO ......................... 1.3 µV/13.2 dBf (40 kHz dev. S/N 26 dB)STEREO ...................... 45 µV/42.1 dBf (46 kHz dev. S/N 46 dB)
Total harmonic distortion (1 kHz)MONO ........................................................ 0.2% (71.2 dBf input)STEREO .................................................... 0.8% (71.2 dBf input)
Signal to noise ratio (DIN weighted)MONO .................................. 65 dB (40 kHz dev. 71.2 dBf input)STEREO .............................. 60 dB (46 kHz dev. 71.2 dBf input)
Stereo separation (DIN 1 kHz) ................................................... 36 dBSelectivity (DIN ± 300 kHz) ........................................................ 64 dBFrequency response ................. (30 Hz ~ 15kHz), +0.5 dB, –3.0 dB
AM tuner sectionTuning frequency range ................................... 531 kHz ~ 1,602 kHzUsable sensitivity ................................................. 16 µV / (600 µV/m)Signal to noise ratio (30% mod. 1 mV input) ........................... 50 dB
GENERALPower consumption .................................................................. 250 WAC outlet
SWITCHED ...................................................... (total 90 W max.)Dimensions ...................................................................... W : 440 mm
H : 143 mmD : 400 mm
WeightKRF-V6050D ............................................................................... 8.6 kgKRF-V5050D ............................................................................... 8.5 kg
Notes1. KENWOOD follows a policy of continuous advancements in development. For this reason specifications may be changed without notice.2. The full performance may not be exhibited in an extremely cold location (under a water-freezing temperature).
For your recordsRecord the serial number, found on the back of the unit, in the spacesdesignated on the warranty card, and in the space provided below. Referto the model and serial numbers whenever you call upon your dealer forinformation or service on this product.
Model __________________ Serial Number ________________________
*_4947/27-40/EN 3/15/01, 9:58 AM40