ASSA ABLOY Non-Hold Open and Hold Open Models · ISW91B/OS (01-16) Rixson® is a registered...
Transcript of ASSA ABLOY Non-Hold Open and Hold Open Models · ISW91B/OS (01-16) Rixson® is a registered...
B/OS ( )ISW91 01-16Rixson® is a registered trademark of Yale Security Inc., an ASSA ABLOY Group company. Copyright © 2016 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.
ASSA ABLOY
RIXSON®
1
*Butt or 3/4 Offset Pivot Hung, Multi Sized 1-3, 3-6Non-Hold Open and Hold Open Models
Model W91 Overhead Concealed ClosersWood Frame Installation Instructions
ASSA ABLOY
RIXSON®
TO DETERMINEHAND OF
YOUR DOOR:
IMPORTANT:
BEFOREINSTALLING:
• An improperly installed or incorrectly adjusted door closer may cause property damage or personal injury and will void product warranty.• To avoid personal injury, DO NOT DISASSEMBLE THIS DOOR CLOSER BODY. • Door closers must be securely fastened to a prepped door and frame with fasteners provided.• HOLD OPEN option not permitted to be installed in fire door assemblies.
• The Americans with Disabilities Act (ADA) requires that doors having door closers have an opening force not to exceed 5 lbf. • The door closer's power size adjustment feature may require adjustment to its lowest setting to comply with ADA opening force guidelines.• An auxiliary door stop, Rixson Checkmate surface applied overhead stops or others, is strongly recommended to avoid damage to the door closer and adjacent property.• Doors should be hung on ball bearing or anti-friction hinges/pivots.• ADA compliant closers may not latch doors, manufacturer does not guarantee latching on lower opening force settings.
LEFTHANDDOOR
RIGHTHANDDOOR
RHR LHR
*Other means except 4-1/2" x 4-1/2" or 3/4" offset pivot hung, consult factory.
B/OS ( )ISW91 01-16Rixson® is a registered trademark of Yale Security Inc., an ASSA ABLOY Group company. Copyright © 2016 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.
ASSA ABLOY
RIXSON®
2
Mo
del
W91
Ove
rhea
d C
on
ceal
ed C
lose
r B
utt
Hin
ge,
Wo
od
Fra
me
OC
60
92
412
/15
Rix
son®
is a
reg
iste
red
trad
emar
k of
Yal
e S
ecur
ity In
c., a
n A
SS
A A
BLO
Y G
roup
com
pany
. Cop
yrig
ht©
201
5, Y
ale
Sec
urity
Inc.
, an
AS
SA
AB
LOY
Gro
up c
ompa
ny.
All
right
s re
serv
ed. R
epro
duct
ion
in w
hole
or
in p
art w
ithou
t the
exp
ress
writ
ten
perm
issi
on o
f Yal
e S
ecur
ity In
c. is
pro
hibi
ted.
A r
em
ovable
fra
me s
top m
ust be u
sed in c
om
bin
ation
with
the c
loser
for
pro
per
insta
llation. M
ounting h
ole
sfo
r fr
am
e s
top m
ust span c
loser
length
. S
top m
ust be
rem
ovable
to insta
ll clo
ser
and m
ake p
roper
adju
stm
ents
.
Clo
ser
22-3
/4(5
78)
5/8
(16)
2-3
/4(7
0)
Max. D
eg
ree o
f O
pen
ing
91 N
on H
old
Open (
135°)
With T
rack S
top
91 N
on H
old
Open (
180°)
Without T
rack S
top
91H
Hold
Open (
105°)
23-5
/8(6
00)
Varies
with
Door
Thic
kness
7/8
(22)
1-1
/4(3
2)
1/4 (6)
22-1
/2 (
572)
Length
of T
rack
Top o
f D
oor
23-5
/8 (
600)
Cuto
ut fo
r A
rm
23-5
/8 (
600)
Length
of M
ort
ise
"A"
Dim
ensi
on
Sta
ndard
Applic
atio
n
Retr
ofit
Tra
ck O
ptio
n
1-1
/16"
(27)
1-3
/8"
(35)
3/4
(19)
Wo
od
Mo
un
tin
g
Clip
A
A
Clo
se
r M
ounting
Pla
te
Tra
ck
Optional S
pacer
No
tes:
1. F
or
18
0°
op
en
ing
, m
ax.
allo
wa
ble
bu
tt h
ing
e
size
is 5
" x
5".
2. M
in. st
op
th
ickn
ess
1/2
".3
. 1
/8"
do
or
to s
offit
cle
ara
nce
re
qu
ire
d.
4. R
ein
forc
ing
pe
r A
NS
I/S
DI-
10
0
reco
mm
en
de
d fo
r h
ollo
w m
eta
l do
ors
an
d
fra
me
s.5
. A
uxi
liary
sto
p r
eco
mm
en
de
d.
6. D
o n
ot sc
ale
dra
win
g.
7. D
ime
nsi
on
s g
ive
n in
inch
es
(mm
).
Le
ft H
an
d D
oo
r a
nd
Clo
ser
Sh
ow
nR
igh
t H
an
d O
pp
osi
te
Rem
ova
ble
Sto
p
1-1
5/1
6(4
9)
Reveal
1/8
(4)
Fro
m E
dge o
fF
ram
e In A
ll C
ases
4-9
/16
(116)
3-3
/4(9
5)
Clo
ser
Wid
th
1/8 (4)
5/8
(16)
22-3
/8(5
68)
4-1
5/1
6(1
25)
5-3
/8(1
36)
22-3
/4(5
78)
7/1
6(1
1)
1-3
/4(4
4)
Cuto
ut fo
r arm
incl
udes
heel o
fdoor
as
show
n.
5/1
6(8
)
DO
OR
2-1
/16
(52)
1-1
/16
(27)
2-1
/16
(52)
7-7
/16
(189)
17-3
/16
(436)
22-9
/16
(573)
ww
w.r
ixso
n.co
m
ASSA
AB
LOY
RIX
SON
®
DAT
ET
EM
PLA
TE
NU
MB
ER
B/OS ( )ISW91 01-16Rixson® is a registered trademark of Yale Security Inc., an ASSA ABLOY Group company. Copyright © 2016 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.
ASSA ABLOY
RIXSON®
3
Mo
del W
91 O
verh
ead
Co
nceale
d C
loser
3/4
" O
ffset
Piv
ot
Tem
pla
te
A r
em
ova
ble
fra
me s
top m
ust
be u
sed in
com
bin
atio
nw
ith th
e c
lose
r fo
r pro
per
inst
alla
tion. M
ountin
g h
ole
sfo
r st
op m
ust
span c
lose
r le
ngth
. S
top m
ust
be r
em
ova
ble
to in
stall
close
r and m
ake
pro
per
adju
stm
ents
.
4-1
/2(1
14.3
)M
in.
9/6
4 (
4)
Fro
m E
dge o
fF
ram
e In A
ll C
ase
s
3-2
3/3
2"
(94.5
)C
lose
r C
uto
ut
Clo
ser
Base
Pla
te
Retr
ofit
Tra
ck S
pace
r(O
ptio
nal)
Clo
ser
Rem
ova
ble
Sto
p
Tra
ck
Min
Fra
me
2-1
/4(5
7.2
)
1-3
/4(4
4.5
)M
in. C
lose
rC
uto
ut
1-1
5/1
6(4
9)
Reve
al
1/8
(3.2
)
Wood M
ountin
gC
lip H
ole
s(4
Pla
ces)
5"
(127)
22-3
/4(5
77.9
)
2-3
/4(6
9.9
)
Clo
ser
Attach
ing S
crew
s#14 x
1-1
/2 F
HP
WS
(4 P
lace
s)20-5
/8(5
23.9
)
22-1
/2 (
571.5
)Length
of M
ort
ise for
Tra
ck
1-1
/2(3
8.1
)
Tra
ck S
crew
s#14 x
1 F
HP
WS
(4 P
lace
s)
1"
(25.4
)5-3
/8(1
36.5
)
15-1
/8(3
84)
20-1
/2(5
21)
7/8
(22.2
)1-1
/4(3
1.8
)
1/4
(6.4
) R
egard
less
of D
oor
Thic
kness
Varies
With
D
oor
Thic
kness
19"
482.6
)C
uto
ut fo
r A
rmC
uto
ut A
t To
p O
f D
oor
On S
top S
ide O
NLY
Do N
ot C
ut B
oth
Sid
es
of D
oor
Max.
Degre
e o
f O
penin
g -
115°
91 N
on H
old
Open (
Up to 1
15°)
91 H
old
Open (
85°)
Doors
must
be b
eve
led 1
/8"
in 2
".
4-9
/16
(116)
Model 1
80
Rix
son P
ivot
1-1
/16
(27)
OC
60936
ww
w.r
ixso
n.co
m
ASSA
AB
LOY
RIX
SON
®
DAT
ET
EM
PLA
TE
NU
MB
ER
Rix
son®
is a
reg
iste
red
trad
emar
k of
Yal
e S
ecur
ity In
c., a
n A
SS
A A
BLO
Y G
roup
com
pany
. Cop
yrig
ht©
201
5, Y
ale
Sec
urity
Inc.
, an
AS
SA
AB
LOY
Gro
up c
ompa
ny.
All
right
s re
serv
ed. R
epro
duct
ion
in w
hole
or
in p
art w
ithou
t the
exp
ress
writ
ten
perm
issi
on o
f Yal
e S
ecur
ity In
c. is
pro
hibi
ted.
08/1
5
5/8
(15.9
)
4-9
/16
(115.9
)23-5
/8(6
00)
Typ
7/1
6(1
1)
Typ
Top o
f D
oor
A
"A"
Dim
ensi
on
Sta
ndard
Applic
atio
n
Retr
ofit
Tra
ck O
ptio
n
1-1
/16"
(27)
1-3
/8"
(35)
3/4
(19)
3/4
(19)
4
B/OS ( )ISW91 01-16Rixson® is a registered trademark of Yale Security Inc., an ASSA ABLOY Group company. Copyright © 2016 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.
ASSA ABLOY
RIXSON®
Components: Figure 1
• It is recommended that the door, in which the door closer will be installed, be hung on ball bearing hinges or pivots. Door must swing freely. For other hanging means a special layout may be required, consult factory.
®• A separate Rixson Surface Checkmate or other door stop, supplied by others, is recommended to prevent damage to the door closer, closer arm; or to the door, frame or adjacent walls.
• Door and Frame must be reinforced for attaching screws.• All dimensions are given in inches with corresponding metric dimensions (millimeters) in parentheses.
(Optional) Hold OpenTrack Assembly
90254
Arm
CloserRH Arm - 90237***LH Arm - 90236***
Track90239
Retrofit Track Spacerand Screws (Optional) 90260(Not for new installation. Forreplacement only. Consult factory.)
Non-Hold OpenStop Block Assembly
90255
Slider90253
WoodMounting
Clips90257
CloserScrew Pack
90241-***
ArmScrew Pack
90259-***
TrackScrew Pack
90242
Left hand shown
5
B/OS ( )ISW91 01-16Rixson® is a registered trademark of Yale Security Inc., an ASSA ABLOY Group company. Copyright © 2016 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.
ASSA ABLOY
RIXSON®
• Attach wood clips to closer body with 1/4-20 x 5/8 FHPMS.
• Install closer with attached wood clips into frame with (4) #14 x 1-1/2 FHPWS mounting screws provided. Mounting plate should be flush with frame soffit.
Closer Installation2• Left hand door illustrated.
#14 x 1-1/2 FHPWS(4 each)
!
• Note if the gaps between door and frame are consistent. Gap should be 1/16" at jamb and header.
• Using attached templates, check all dimensions of cut-outs.
Verify Door Installation For Correctness1• Make sure the frame is plumb and square by using a carpenters' square.
Check Arm Position3
Arm Position Prior To Door Attachment
APPROX15°
The arm should be at approximately 15 degrees away from the door side of the closer mounting plate prior to door attachment. Arm always rotates in direction of door.
Door Side
1/16"(1.6)
B/OS ( )ISW91 01-16Rixson® is a registered trademark of Yale Security Inc., an ASSA ABLOY Group company. Copyright © 2016 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.
ASSA ABLOY
RIXSON®
6
Track Installation5• Be sure to check that the
slider and any track assembly components are installed prior to track installation.
• Install track and/or (optional) spacer (replacement application only, consult factory) using provided hardware in prepped door.
!Long end of slider must be oriented
toward the hinge/pivot end of door.
Assembly of Track Components4• Slide track assembly components in
track.
• Stop block assembly or (optional) hold open assembly should be mounted towards the hinge side of the track as shown. The longer end of the slider should be pointed towards the hinge end of the track.
(Optional) Hold Open Track Assembly Install Components
Non Hold Open Track Assembly Install Components
14-1-5/8 FHPWS (4 each)
Slider
Slider
B/OS ( )ISW91 01-16Rixson® is a registered trademark of Yale Security Inc., an ASSA ABLOY Group company. Copyright © 2016 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.
ASSA ABLOY
RIXSON®
7
6
1. With a 1/8" hex wrench, completely tighten the latch and sweep adjustments by turning the screws clockwise. This will allow for an easier closer/door connection.
2. Open door to about 45 degrees then rotate arm over to door. The arm should maintain position since the latch and sweep adjustments have been closed.
3. Align slider square with arm square and connect the two using the provided screw. If you choose to open the door beyond 45 degrees, note that the backcheck adjustment screw may have to be adjusted counterclockwise to easily rotate arm to door position.
SweepLatch
Closer/Door Attachment
Backcheck
1/8"HexKey
1/4-20 x 3/4 Flat Head Hex Machine Screw w/Loctite
Provided
B/OS ( )ISW91 01-16Rixson® is a registered trademark of Yale Security Inc., an ASSA ABLOY Group company. Copyright © 2016 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.
ASSA ABLOY
RIXSON®
8
Closer Adjustments
!Do not take
adjustment screws out or closer will leak oil.
S-SweepL-LatchB-Backcheck
Opening ForceAdjustment
!
!
7
USE HEX KEYS TO MAKE ANY CLOSER ADJUSTMENTS.
DO NOT USE POWER DRIVERS.
Do not use backcheck to
achieve dead stop.
Spring Adjustment
Closer
Size
Approx. # of
Turns
Closer
Size
Approx. # of
Turns
ADA 0 3 0
1 15 4 17
2 30 5 25
3 55 6 32
Model PH91 Sizes 1-3 Model 91 Sizes 3-6
Closer shipped at lowest spring setting.
"L"Latch
0°
5°
1/8"HexKey
wo el rS
Fa rste
+
-
1/8"HexKey
"B"Backcheck
75°Weaker
Stronger
• Opening Force AdjustmentLocate opening force adjustment hex.Using 3/8" hex key, adjust opening force prior to sweep and latch adjustments.Size 1-3, 3-6 adjustment, see chart at right.
All 91 series closers are factory set to minimum opening force. Adjust closer as necessary for more closing force taking into consideration door size, weight, positive room pressure, etc. A lower opening force means a lower closing force. To achieve stronger closing forces, turn 3/8" hex clockwise. Keep in mind that the opening force will be increased as well.
After the opening/closing force has been set to satisfactory forces to close the door, adjust the sweep, latch and backcheck valves to control the speed of the door. Holes are shown in the mounting plate above to provide access to the adjustment valves using a 1/8" hex wrench.
"S"Sweep
5°
1/8"HexKey
wo el rS
Fa rste
B/OS ( )ISW91 01-16Rixson® is a registered trademark of Yale Security Inc., an ASSA ABLOY Group company. Copyright © 2016 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.
ASSA ABLOY
RIXSON®
9
Removable Stop Installation9• After closer is installed and
all adjustments are complete, install removable stop.
!No holes should be drilled in the closer
mounting plate.
(Optional) Hold Open Adjustment8
• Engage locking tab of hold open assembly in track slider. Hold open assembly should be on hinge side of track slider. Open door to desired hold open position. Tighten hold open mounting set screws to lock down hold open assembly. Pull door in the closing direction to disengage hold open assembly and track slider. To increase the amount of force necessary to pull door out of hold open, tighten the holding force adjustment screw clockwise. To decrease the amount of force necessary to pull door out of hold open, loosen the holding force adjustment screw counterclockwise.
NOTE: THIS FEATURE CANNOT BE USED ON FIRE-RATED DOORS
SetScrews
HoldingForce
AdjustmentScrew
Locking Tab
Track Slider
+
-Decrease
Increase
B/OS ( )ISW91 01-16Rixson® is a registered trademark of Yale Security Inc., an ASSA ABLOY Group company. Copyright © 2016 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.
ASSA ABLOY
RIXSON®
10
3000 Highway 74 East • Monroe, NC 28112Tel: (866)- 9766474-
www.r ixson.com
ASSA ABLOY
RIXSON®
Troubleshooting
Symptom Cause Remedy
Use spring adjuster to increase tension. See Step 7.
Adjust latch speed valve. See Step 7.
Send template for the hanging means to the factory. A new installation sheet is required. Closer will need to be relocated.
See Step 6.
Use spring adjuster to decrease tension. See Step 7.
Spring tension not strong enough.
Latch speed control not fast enough.
Door hung on products other than 4-1/2 x 4-1/2 butts or 3/4 offset pivots.
Arm is not preloaded.
Door won't latch.
Spring tension is set too strong.Door is too difficult to open.