Art 12 x 10 Measure art, i.e. 12 x 10 Measure Face (width) of molding i.e. 1 ½ wide Add width of...
-
Upload
alban-sims -
Category
Documents
-
view
214 -
download
2
Transcript of Art 12 x 10 Measure art, i.e. 12 x 10 Measure Face (width) of molding i.e. 1 ½ wide Add width of...
![Page 1: Art 12 x 10 Measure art, i.e. 12 x 10 Measure Face (width) of molding i.e. 1 ½ wide Add width of Art (12) + 2 x width of Frame (3) = 15 inches + 1/8 inch.](https://reader036.fdocuments.us/reader036/viewer/2022082818/56649f165503460f94c2cd3d/html5/thumbnails/1.jpg)
Art
12 x 10
• Measure art, i.e. 12 x 10• Measure Face (width) of molding i.e. 1 ½ wide• Add width of Art (12) + 2 x width of Frame (3) = 15 inches + 1/8 inch for glass• Cut ‘Top and bottom’ stock 2 @ 15 1/8 OSM• Cut sides (10) + (3) + (1/8) 2 @ 13 1/8 OSM
Frame stock 1 ½ wide
![Page 2: Art 12 x 10 Measure art, i.e. 12 x 10 Measure Face (width) of molding i.e. 1 ½ wide Add width of Art (12) + 2 x width of Frame (3) = 15 inches + 1/8 inch.](https://reader036.fdocuments.us/reader036/viewer/2022082818/56649f165503460f94c2cd3d/html5/thumbnails/2.jpg)
Rabbet
Bottom
BackFace
¼’’
¼’’
Side View of molding
![Page 3: Art 12 x 10 Measure art, i.e. 12 x 10 Measure Face (width) of molding i.e. 1 ½ wide Add width of Art (12) + 2 x width of Frame (3) = 15 inches + 1/8 inch.](https://reader036.fdocuments.us/reader036/viewer/2022082818/56649f165503460f94c2cd3d/html5/thumbnails/3.jpg)
•Mill all required stock
•Finish entire run of stock
![Page 4: Art 12 x 10 Measure art, i.e. 12 x 10 Measure Face (width) of molding i.e. 1 ½ wide Add width of Art (12) + 2 x width of Frame (3) = 15 inches + 1/8 inch.](https://reader036.fdocuments.us/reader036/viewer/2022082818/56649f165503460f94c2cd3d/html5/thumbnails/4.jpg)
T & B
Sides
• T & B 2@ 15 1/8 OSM
• Sides 2@ 13 1/8 OSM
• Cut ‘Longer’ sides first, in case of error they can be used for short sides
• After cutting verify both ISM (12 1/8) & OSM dimensions (15 1/8)
![Page 5: Art 12 x 10 Measure art, i.e. 12 x 10 Measure Face (width) of molding i.e. 1 ½ wide Add width of Art (12) + 2 x width of Frame (3) = 15 inches + 1/8 inch.](https://reader036.fdocuments.us/reader036/viewer/2022082818/56649f165503460f94c2cd3d/html5/thumbnails/5.jpg)
1. Use ‘V’ vise to hold pieces
2. Small amount of glue on each
3. Drill with nail into ‘Top’ and ‘Bottom’
![Page 6: Art 12 x 10 Measure art, i.e. 12 x 10 Measure Face (width) of molding i.e. 1 ½ wide Add width of Art (12) + 2 x width of Frame (3) = 15 inches + 1/8 inch.](https://reader036.fdocuments.us/reader036/viewer/2022082818/56649f165503460f94c2cd3d/html5/thumbnails/6.jpg)
Side View of molding
1. Glass
2. Matting
3. Picture
4. Foamcore
5. Staple
6. Paper
![Page 7: Art 12 x 10 Measure art, i.e. 12 x 10 Measure Face (width) of molding i.e. 1 ½ wide Add width of Art (12) + 2 x width of Frame (3) = 15 inches + 1/8 inch.](https://reader036.fdocuments.us/reader036/viewer/2022082818/56649f165503460f94c2cd3d/html5/thumbnails/7.jpg)
Mount wire apx. 25% down from Top