Amphenol BCD 87010
1
815.399.0001 outside the U.S.A. • [email protected] INTERNATIONAL, INC. 33 Omnidirectional Antenna Mechanical specifications Length BCD-80010, BCD-80610 & 82510 Overall 3445 mm 136 in Radome 2945 mm 116 in BCD-87010 Overall 3393 mm 134 in Radome 2893 mm 114 in Diameter 65 mm 2.6 in Weight 12 kg 26.5 lbs Wind area 0.22 m 2 2.43 ft 2 Wind load at 50m/s 351 N 79 lbs Support pipe Aluminum alloy diameter 70 mm (2.76 in) length 500 mm (19.7 in). Antenna consisting of aluminum alloy. Dipoles covered by a polyurethane painted fiberglass radome. Inverted models available. Electrical specifications Frequency range BCD-80010 806-900 MHz BCD-80610 806-941 MHz BCD-82510 825-960 MHz BCD-87010 870-960 MHz Impedance 50 3) Connector N,NE,DIN, E DIN or EIA 1) VSWR , 2 1.43:1 Polarization Vertical 1) Gain 10 dBd 2) Power rating 500 W 1) Half power angle H-plane 360° E-plane 7° 1) Lobe tilt 1.25° 1) Null fill 5% Lightning protection Direct ground See pages 37 & 38 for lobe tilt and null fill combinations. BCD-80010/80610/82510/87010 BCD-80010/80610/82510/87010 Horizontal Vertical Radiation-pattern (at mid-band) 270 280 290 250 300 240 230 220 210 200 310 320 330 340 190 180 350 0 170 160 10 20 150 140 130 120 110 70 100 80 90 60 50 40 30 -5 -10 -15 -20 -25 260 -30 -35 -30 -25 -20 -15 -5 -10 -35 270 280 290 250 300 240 230 220 210 200 310 320 330 340 190 180 350 0 170 160 10 20 150 140 130 120 110 70 100 80 90 60 50 40 30 -5 -10 -15 -20 -25 -30 -25 -20 -15 -5 -10 260 -35 -30 -35 Antel’s unmatched antenna design includes: • A four-channel extruded aluminum frame running the entire length of the antenna. • Brass feedlines - No high-loss coaxial cable. • Feedlines connected by threaded holes, nuts & bolts - No solder joints. • Air as insulation. • A unique radome with interlocking fiber glass applied both horizontally and vertically for maximum strength. Every Antel antenna is under a five-year limited warranty for repair or replacement. Standard and Inverted Models Available. 1) Typical values. 2) Power Rating limited by connector only. 3) NE indicates an elongated N Connector. E DIN indicates an elongated DIN connector EIA indicates a 7/8" EIA Flange. Improvements to mechanical and/or electrical performance of the antenna may be made without notice. Radiation patterns for all Antel antennas are measured with the antenna mount- ed on a fiberglass pole. Tabulated Data is available in the following formats: ASCII, Granet, LCC/Anet, Lucent, Motorola, Planet, and WIZARD.
description
Amphenol BCD 87010 Antenna Datasheet
Transcript of Amphenol BCD 87010
-
815.399.0001 outside the U.S.A. [email protected], INC.
33
Omnidirectional Antenna
Mechanical specificationsLength
BCD-80010, BCD-80610 & 82510Overall 3445 mm 136 inRadome 2945 mm 116 in
BCD-87010Overall 3393 mm 134 inRadome 2893 mm 114 in
Diameter 65 mm 2.6 in
Weight 12 kg 26.5 lbs
Wind area 0.22 m2 2.43 ft2
Wind loadat 50m/s 351 N 79 lbs
Support pipe
Aluminum alloy diameter 70 mm(2.76 in) length 500 mm (19.7 in).
Antenna consisting of aluminum alloy.Dipoles covered by a polyurethanepainted fiberglass radome. Invertedmodels available.
Electrical specificationsFrequency range
BCD-80010 806-900 MHzBCD-80610 806-941 MHzBCD-82510 825-960 MHzBCD-87010 870-960 MHz
Impedance 503) Connector N,NE,DIN,
E DIN or EIA1) VSWR ,21.43:1
Polarization Vertical1) Gain 10 dBd2) Power rating 500 W1) Half power angle
H-plane 360E-plane 7
1) Lobe tilt 1.251) Null fill 5%
Lightning protection Direct groundSee pages 37 & 38 for lobe tilt and nullfill combinations.
BC
D-8
0010/80610/8
2510/8
7010
BCD-80010/80610/82510/87010
Horizontal
Vertical
Radiation-pattern(at mid-band)
270 280290250
300240
230
220
210
200
310
320
330
340
190
180
350
0
170
160
10
20
150
140
130
120110 70
100 8090
60
50
40
30
-5 -10 -15 -20 -25
260
-30 -35 -30 -25 -20 -15 -5-10-35
270 280290250
300240
230
220
210
200
310
320
330
340
190
180
350
0
170
160
10
20
150
140
130
120110 70
100 8090
60
50
40
30
-5 -10 -15 -20 -25 -30 -25 -20 -15 -5-10
260
-35-30 -35
Antels unmatched antenna design includes:
A four-channel extruded aluminum frame running the entire length of the antenna.
Brass feedlines - No high-loss coaxial cable.
Feedlines connected by threaded holes, nuts & bolts - No solder joints.
Air as insulation. A unique radome with interlocking fiber
glass applied both horizontally and vertically for maximum strength.
Every Antel antenna is under a five-yearlimited warranty for repair or replacement.
Standard and Inverted ModelsAvailable.
1) Typical values.
2) Power Rating limited by connector only.
3) NE indicates an elongated N Connector.E DIN indicates an elongated DIN connectorEIA indicates a 7/8" EIA Flange.
Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Radiation patterns for all Antel antennasare measured with the antenna mount-ed on a fiberglass pole.
Tabulated Data is available in the following formats: ASCII, Granet, LCC/Anet, Lucent, Motorola, Planet, and WIZARD.
*ANTL-1000 BCD/BCR 26-49 2/3/00 10:29 AM Page 9
