Amhara Water Works Enterprise Compliance
-
Upload
agegnehutamirat -
Category
Documents
-
view
287 -
download
0
Transcript of Amhara Water Works Enterprise Compliance
-
8/22/2019 Amhara Water Works Enterprise Compliance
1/24
I. GENERAL SPECIFICATION REQUIREMENT1. GENERAL REQUIREMENT Statement of Compliance with remarks
1.SERVICE REQUIREMENT
The vehicle to be supplied will be used for road
construction and maintenance projects in Ethiopia where:
Climate varies from humid tropics to arid desert Temperature vary from 00c to 500c. Altitude vary from sea level to 2,100 meters above the
sea level.
The vehicle shall be of extra heavy duty and tropical type
capable enough to render trouble free service under extremely
sever operation condition where grade of fuel is generally used;sand/dust will be thickly blown-up and uneven, bumpy and loose,
gravel road surfaces are predominant.
We offer 4(Four) units of Caterpillar model 770
off-highway trucks, which are extra heavy duty
tropical type, capable enough to render trouble
free services in Ethiopia under the following site
conditions;
Climate varies from humid tropics to ariddesert.
Temperatures vary from 00c to 500c.Altitudes vary from sea level to 3000 meters
above the sea level.
2. Manufacturing Requirement2.1GENERAL
All parts components, accessories &attachments, not specifically mentioned in
these specifications but essential for
dependable and efficient operation of the
vehicle, shall be furnished by the supplier asparts of his bid & shall be accordance with
current engineering and manufacturing
practices and according to prevailing trade
provisions in general and/or as promoters of
safe, effective and efficient function of the
unit.
The vehicle to be supplied shall betropicalized, reliable and dependable for
operation under the conditions specified in
the service requirement.
2.2MATERIALSThe materials of which all parts, attachments,
accessories and components of the unit bid upon
which are manufactured and assembled shall be of
-
8/22/2019 Amhara Water Works Enterprise Compliance
2/24
the current technology durable and reliable for
the intended service. The finish shall be high
quality and good workmanship with dependable
operation.
2.3PE-DELIVERY SERVICE The bidder/supplier shall undertake
inspection and servicing of the unit,
including washing, greasing, lubrication,
adjustment and calibration (if any), to the
buyers satisfaction before commissioning
and final acceptance of the unit at the
final destination.
The bidder/supplier shall bear all costs(parts, materials, labor, etc) of the pre-
delivery service.
3. BASIC INFORMATION The bidder/supplier shall complete a proper
response to each clause/section of the
specification items details with the
necessary relevant comment. This response
shall clarify any variation or non-compliance
with the specification in the event that the
unit bid upon does not fully comply,referring to do these specifications, failure
to do these might
The words comply, satisfy, or yes or similarwords alone may not be adequate response
to the requirement of the specifications
where if is expected to response in figures,
in words or in clear terms shall be provided
with the offer/bid
All documents manuals, charts, drawingsand manufacturers specification literature
included with the bid shall be in English
The foot of each page of this specificationsand nay attached brochures or any other
technical details shall b signed and stamped
by the bidder
-
8/22/2019 Amhara Water Works Enterprise Compliance
3/24
4. COMPLIANCE TO REQUREMENTSBidders/suppliers are expected to offer vehicle
from their product range that closely meets the
technical specification. However, bids which do
not comply with the fundamental requirementsdescribed in the technical specification may be
rejected as non-responsive.
5. ON SITE WARRANTY The bidder/supplier guarantees that all materials,
parts, components, accessories and attachments
that the unit bid upon have been manufactured
and assembled are of high quality and good
workmanship. The bidder/supplier also guarantees
to replace at this cost (DDU cost plustransportation and all labor charges up to the
worksite and or final destination) any part or
component that may break or fail by reason of
inferior or defective material and/or
workmanship within the warranty period.
The warranty period shall be 12 months or50,000km whichever comes first from the date
of formal acceptance.
The bidder/supplier shall undertake to rectifyfaults under warranty upon notification by ARWE
within a maximum of 45 calendar days from dateof notification of such occurrences by the
concerned body of ARWE. Failure to do so will
result in remedial action being undertaken by
ARWE. At the risk and expense of the
bidder/supplier.
ARWE reserves the right to further claim fordown time costs if faults are not rectified within
a specified time above.
Specify extra (additional) warranty period forthe engine and other drives.
6.Proven PerformanceARWE shall consider the previous performance
of the offered make within Ethiopia.
7.After Sales Service Facility
-
8/22/2019 Amhara Water Works Enterprise Compliance
4/24
ARWE shall consider supplier having a well
established dealership and after sales service
facility such as its own well organized
workshop and spare part warehouse in Ethiopia.
8.Recommended Spare Parts List The bidder shall furnish itemized and individually
priced suggested list of recommended spare part
for 80,000km driving mileage.
The suggested list of recommended parts shall becomprehensive enough both in the number of line
items of spare parts and quantity per line item
needed by the vehicle system for the indicatedduration. However, the total list price shall not
exceed 15% of the value of the complete match
machine to be supplied.
9. TrainingTechnical training shall be provided locally at the
expense of the supplier as follows:
In operation of the unit bid to the purchasersemployee at least one operator per unit.
In repair and maintenance of unit bid to thebuyers staff at least five, technical persons.
10. Supply Requirements10.1Manuals
a) 2 operators instruction manualb) 2 diagnostics and workshop repair manualc) 2 spare parts catalogued)
2 maintenance manual
10.2Tools10.1.1 Standard Tools
A set of essential tools which include
appropriate lubrication gun shall be provided
in a lockable toolbox with each unit.
-
8/22/2019 Amhara Water Works Enterprise Compliance
5/24
10.1.2 Special Tools
List of special tools shall be provided with
separate price.
10.3 Fire ExtinguisherOne each multi purpose, proper size fire
extinguisher shall be furnished which each
machine.
10.4 ColorThe vehicle in the supply shall be painted to the
buyers option/choice.
10.5 OptionalItems considered vital by the bidder/supplier for
safe, effective and efficient function of the
vehicle shall be quoted optional as part of the bid.
11. Performance Indicators11.1 Maintenance cost per year (with detail
labor, spare parts, etc)
11.2 Specify certified average fuel consumptionfor the offered vehicle
12. OthersBidder/supplier must provide guaranteed information
as requested hereunder. Failure to do so may be
treated as incomplete and may result in rejection of
their bid as non-responsive.
12.1. Manufacturers recommendation of the change
intervals of lubricant (grease and oils, engine,
hydraulic, transmission final drives gear oils, etc)
considering a 1% sulfur content in the diesel fuel,
working under dusty, sandy and rough terrains
-
8/22/2019 Amhara Water Works Enterprise Compliance
6/24
operating conditions based on 80,000km of driving
mileage.
Lubricant
type
Refill
capacity
(liters)
Change
intervals
in hrs.
or km
Top up
between
change
intervals,
if any
remark
12.2 Manufacturers recommendation of the change
intervals of all filters (air cleaner, engine oil filters,
hydraulic oil transmission oil filters, etc) taking into
account a 1% of sulfur contents in the diesel fuel
working under dusty, sandy and rough terrains
operating conditions based on 80,000km of driving
mileage.
Type of
filter
Unit
price
Quantity
per
machine
Change
intervals
in hr or
km
Remarks
12.3 The spare part held at the agents premises for
the vehicle of offer and the approximate value
with the total number of line items in the stock
for the specific model at the date of bid
submission.
12.4 Maximum parts availability time for the factoryto the local agents premises and/or to the
purchaser by air and sea/ocean freight.
12.5 Details about workshop facilities for after sales
services by faculties including office, parts shop,
repair shops indoor parking places, service in
-
8/22/2019 Amhara Water Works Enterprise Compliance
7/24
operator training, etc.
13. Specification WaiverThe buyer reserves the right to partially or fully
waive compliance to any of these specifications and
make award on the basis that interest of the buyer
is best served.
-
8/22/2019 Amhara Water Works Enterprise Compliance
8/24
II. TECHNICAL REQUIREMENTSSpecification Requirement Statement of Compliance
1.Scope It is the intent of these specifications whether or
not specifically mentioned herein to describe a
heavy duty diesel engine driven, quarry steel body
dump truck.
The truck should be suitable for continuousoperation in tropical conditions specified under
service requirement of Part I general specification
herewith and very rough terrain as well as dusty,
rock and sandy areas.
Maximum gross vehicle weight shall be 75,500kgs Dump body capacity not less than 20m3 when
handling up to 1600kg/m3 material density. The
payload capacity of the track shall be minimum 40
tons.
All items to be fully assembled with the entirenecessary fittings and attachments and tested
ready for immediate use.
Due consideration will be given for bids whichprovided interchanging of parts between models.
2.Engine2.1General
The diesel engine shall perform smoothly and
efficiently under all conditions of operation above
and shall develop the rated horsepower when
operating on commercial diesel fuel with sulfur
content of 1% and cetane number of 50.
2.1.1Engine PerformanceThe engine shall be capable of sustained
operation at about 65km/hr with truck
loaded to its maximum payload capacity
without over loading the engine under
conditions specified in requirement.
2.2TypeThe engine shall be four cycle, water cooled,
diesel, direct injection and turbocharged,
-
8/22/2019 Amhara Water Works Enterprise Compliance
9/24
preferably with after enter cooler, with not less
than six cylinder and shall be equipped with
replaceable cylinder sleeves preferably wet type
liner.
2.3Flywheel Horse PowerThe engine shall deliver minimum 480 BHP min.
SAE J 1349 net at flywheel at rated RPM,
equipped with fuel pump, cooling fan, heavy duty
radiator, lubricating oil pump, air cleaner,
alternator and any other required engine
accessories.
2.4Required Engine DataThe manufacturer shall submit certified engine
data according to SAE standard with his bid
showing net power, torque and specific fuel
consumption curves at governed RPM at sea level
and 2500 elevation.
The supplier shall also furnish certified average
fuel consumption per Km. when the truck is
working under heavy workload.
2.5Lubrication SystemEngine lubrication system shall be of the full
force feed type, by a gear driven oil pump or
equivalent, through oil clarification, by two
replaceable filters (filters through full flow and
by pass cartridge filters or filters of better
filtration system) shall be provided. The engine
oil filler cap permanently attached to filler neck
(oil collar shall incorporate in the lubrication
system.
2.6Starting SystemThe engine shall be equipped with heavy duty 24V
direct electric starting system. An electric motor
-
8/22/2019 Amhara Water Works Enterprise Compliance
10/24
shall start the engine satisfactorily at
temperatures as low as 00C without recourse to
any auxiliary heating or starting device, glow
plugs, or fluid priming system preferably be
reduction type starter motor having about 7kw
rated capacity is required.
2.7Air CleanerHeavy duty of two stage dry type air cleaner
fitted with preferably a cyclone type per cleaner
(automatic dust evacuator and dust indicator)
with restriction gauge/indicator of ample
capacity shall be furnished. The restriction
gauge/indicator shall be well protected from
external damage and strong enough to withstand
shocks and impacts.
3.Fuel System3.1Fuel TankThe fuel tank or tanks shall be properly ventilated,
made from repairable steel, protected both internally
and externally from corrosion and must incorporate a
baffled sump, to collect water formed by a
condensation, properly supported with an underside
sheet metal for protection. Fuel tank(s) made from
plastic will not be accepted. Fuel tank cap shall be
self-closing type permanently fixed on the filler neck
(fuel tank cap should be secured to filler neck by
chain). Tank filler shall contain strainer.
Fuel tank(s) capacity shall be minimum 400 liters.
3.2Injection PumpInjection pump shall be mechanically driven with all
necessary regulatory and controlling attachment.
3.3InjectorsInjectors shall be accessible, interchangeable and
-
8/22/2019 Amhara Water Works Enterprise Compliance
11/24
readily removable.
3.4Fuel FiltersThe fuel filters shall be minimum two in series and
shall be accessible, replaceable and readily removablefor quick maintenance.
3.5Water SeparatorWater separator shall be incorporate in the fuel
filtration system.
4.Cooling SystemThe cooling system shall be of tropicalized closed,
pressurized, pump forced type water medium with
ample capacity to permit continuous full load
operation of the engine without boiling of the coolant
under the conditions specified in the service
requirement herein. The cooling system shall
incorporate an efficient tropicalized thermostat.
4.1RadiatorThe radiator shall be tropicalized of the heavy duty
construction (upper and lower channels/tanks as well
as core shall be made from brass and/or copper of
repairable type) properly mounted to withstand
shocks and strains likely to be encountered in
operation. The radiator shall have adequate capacity
and flow area, plus a compensation for the altitudes
and temperatures in Ethiopia. The radiator shall be
easily removable and cap with strong chain
permanently attached to the radiator shall be
furnished.
The corrosion circuit or equivalent shall be provided
for the purpose of preventing collection of rust and
dust, which gives unfavorable effect on the cooling
line and scale to be collected.
-
8/22/2019 Amhara Water Works Enterprise Compliance
12/24
Plastics will not be acceptable in manfacture of any
part of the radiator except the expansion tank.
It is preferred if possible to install water filter
within the cooling system for trapping foreign
materials.
4.2Cooling FanThe cooling system shall be fitted with and adequate
size direct drive cooling fan made from steel and
driven by belt.
5.Electrical SystemThe electric system shall be composed of but not limited
to a complete 24V electric starting, charging and
lighting systems, electric switches and two keys. All
wiring shall be enclosed in non metallic loom and the
system shall be protected by fuse.
5.1AlternatorThe alternator shall be heavy duty, fan ventilated
with electronic voltage regulator, and shall be of
adequate capacity to provide service under normal
operating conditions. Approximate rated capacity of
alternator shall be 24V/50AMP.
5.2Lighting SystemThe lighting system shall consist of but not limited to:
Two adjustable headlights with high and lowbeam
Two parking lights Two combination stop, tail and direction lights Cabin interior light Backup lights with automatically activated
warning device
Instrument panel light Two reflectors and clearance lights Plate number light
-
8/22/2019 Amhara Water Works Enterprise Compliance
13/24
Fog light and any other light required by I.C.Cmotor vehicle safety regulation
Gravel protection wire mesh grill shall beprovided for all lights installed outside the
cabin.
5.3Directional SignalsThe truck shall be equipped with double faced,
directional signals, prominently mounted at each side
of the vehicle on the front. So that front lamps emit
a flashing signal to both front and rear direction. The
front and rear lens shall be amber colored. The
directional signals shall be of the self canceling type
integrally mounted with steering column. Operation of
the directional lamps shall be indicated to the driver
by indicator light and audible signal on the instrument
panel.
Signal lamps must be activated at once by means of
emergency four way flasher switch, which shall be
installed in the system.
5.4Over Load ProtectionFuses, circuit breakers or equal protection against
damage of short circuits shall adequately protect all
electrical circuit. The circuit protection device shall
be located at a point in the circuit between the power
source and the device being protected.
5.5Windshield WipersThe vehicle, two or three electrically operated wipers
shall be required automatic electric windshield
washers shall be installed.
5.6HornsThe vehicle shall be equipped with two types of horns.
The first type will be electrical with activation by
standard steering wheel button mounted type. The
-
8/22/2019 Amhara Water Works Enterprise Compliance
14/24
second type will be air operated with the horn
mounted at convenient locations.
5.7BatteriesThe batteries shall be heavy duty, of ample power tostart the engine when cold at sufficient speed down
to ambient temperature of 00C. Batteries shall one
12V, 70 AH (minimum) at 20 hours rating.
5.7.1 Battery MountingThe batteries shall be mounted at a convenient place
in a metal box, provided with hold down device and
shall be located so as to provide easy access for
servicing proper cushion shall be provided for battery
seat.
6.Exhaust SystemThe truck should be equipped with heavy duty muffler.
The exhaust pipe shall be preferably vertically located
in such a manner that it will not interfere with the
opening and closing of the cab doors. And the exhaust
pipe shall have adequate insulation and be shielded so as
to prevent burring, charring or damage in any way of the
electrical wiring, fuel supply or other components of the
truck.
7.ClutchThe clutch shall of the heavy duty of adequate size and
plate capacity to assure long life under severe operating
conditions as described under service requirement. The
input torque capacity for the clutch as rated by the
manufacture shall not be less than 10% in excess of that
the maximum net torque developed by the engine.
-
8/22/2019 Amhara Water Works Enterprise Compliance
15/24
8.TransmissionThe transmission shall be heavy duty of
manual/automatic and shall have a minimum of six speed
forward and one reverse speed and shall be a
combination of constant mesh synchromesh typepreferably fully synchromesh in all speeds. The maximum
road speed of the vehicle shall preferably be within the
rant of 50-75 KM/hr.
Final Reduction and Grade ability
The final reduction ratio shall enable the vehicle to
negotiate approximately 50% gradient on road at
altitude of 1000m above sea level in first gear, at
maximum torque and permissible GVW without evidence
of overloading the engine.
9.SteeringThe truck shall be equipped with left hand steering.
Hydraulic power assisted steering system is required. In
event of hydraulic failure, truck shall be safety
controlled by manual effort. Means shall be provided for
easy adjustment of lost motion in the steering gear.
Power steering pump shall be gear drive directly
mounted to the engine.
10. CabThe cab shall be all steel construction with dust, heat
and weather proof windows and clear view windows and
clear view window of toughened glass, with
accommodation for the driver and two passengers.
The cab shall be of all steel welded construction of the
manufacturers standard material, forward control type.
It shall be equipped with heater/defroster, ashtray,
cigar lighter and radio cassette player. Conventional cab
will not be accepted.
-
8/22/2019 Amhara Water Works Enterprise Compliance
16/24
10.1 Instrument panel and controlInstrument panel and control shall include but not
limited to:-
Panel lighting Speedometer with odometer calibrated in
kilometer/hr Tachometer Water temperature gauge/indicator (audible
warning light for engine over heating)
Ammeter or charging indicator light Lighting switches Oil filter element clogging indicator Fuel gauge Air cleaner restriction gauge/indicator Oil pressure gauge with warning signal Cab safety lock hatch indicator Windshield wiper control Engine over running warning device Inter axle lock switch Air pressure gauge/low air pressure warning
signal and other required accessories for
proper and efficient operation of truck.
10.2 SeatsDrivers seat shall be of spring suspension type, cloth
covered with water repellent, and shall be with fore
and after adjustment and CO-drivers seat shall also
be upholstered and cushioned. Seat belts shall be
installed.
10.3 Door LocksBoth doors shall locked from inside and at least one
shall locked from the outside preferably with same
key as used in the staring switch.
10.4 GlassAll glass in the cab for windshields and windows shall
be of the laminated plate type known as safety glass
and shall be free from the imperfections or obvious
distortions.
-
8/22/2019 Amhara Water Works Enterprise Compliance
17/24
10.5 Sun VisorsTwo or three adjustable interior sun visors shall be
installed in the cab in accordance to the
manufacturers practice.
10.6 MirrorsLarge articulated external rear view mirrors shall be
installed on both left and rights hand side of the
vehicle. They shall be properly located as to give the
driver a clear view of the high way though each mirror
for a distance at least sixty meters.
11.FrameThe chassis frame shall be of heavy duty construction
and capable of with standing the strain of rigorous on
and off the road surface and shall provide worth
adequate number of cross members, so designed and
constructed as to support the GVW of the vehicle with
its evenly distributed load. Chassis frame tails shall not
project beyond the rear end of the mounted dump body.
12.Dump Body and Tipping Attachments12.1 CapacityThe dump body shall have a minimum of 20m3 struck
capacity. When handling up to 1600kg/m3 material
density.
12.2 Construction
The dump body shall be constructed of high tensilesteel of if not provide detail specification of body
constructed, material type, by specifying yields point,
tensile strength etc). A minimum thickness of 26mm
floor, 14mm sides and preferably a min. of 16mm
front. The quarry dump truck should be designed for
handling rock or wet sand, wet gravel and clay as well
-
8/22/2019 Amhara Water Works Enterprise Compliance
18/24
as blasted rock and crushed aggregates of basalt and
granite. The dump body shall dump at the rear of the
truck only, with a minimum dumping angle of 50
degrees. The dump body shall have lateral
supports/brackets to prevent twisting off the body
during dumping operations.
12.3 Cab ProtectorDump body shall have reinforced steel cab protector
at least 8mm thickness to extend over the cab. The
cab protector shall be mounted on the dump body by a
full ribbon weld and shall be reinforced.
12.4 HoistThe dump body shall be raised and lowered by one or
two hydraulic hoist of adequate size and strength to
raise, hold and safely lower the fully loaded dump
body under all normal working conditions.
12.5 Hoist ControlsPower take off, pump and valve shall be
manufacturers standard for the hoist model
furnished. Valve and power take off controls shall be
located in the cab. A mechanical safety look shall be
permanently fixed to the body to provide positive
retention in the up position for servicing and repair.
13. Axles and Suspension13.1 AxlesThe truck shall be equipped with heavy duty front and
rear axles. The axle capacity ratings shall be at least
to the gross load imposed at the ground when the
vehicles in evenly loaded to its rated G.V.W.
13.1.1 Front AxleThe front axle shall be manufacturers standard, but
heavy duty construction mounted on heavy duty
-
8/22/2019 Amhara Water Works Enterprise Compliance
19/24
springs with extra heavy duty shock absorbers. All
spindles, kingpins thrust bearings and wheel bearings
shall be properly shall be properly sized and matched
with this axle rating.
13.1.2 Rear AxleThe rear axle shall be of the fully oscillating and full
floating type with hub reduction. The torque input
capacity of this shall exceed the total engine torque
developed through the lowest intervening gear
reduction.
13.2 SuspensionHeavy duty semi elliptical front springs and extra
heavy duty rear springs with adequate number of
leaves to sustain smooth operation of the fully loaded
truck shall be provided.
13.3 Shock AbsorbersManufacturers standard heavy duty double acting,
telescopic shock absorber (if equipped with) of
adequate size and capacity shall be mounted at each
side of the chassis.
14. BumpersManufacturers standard heavy duty steel bumper shall
be installed on the front chassis. The bumper shall span
the complete width of the chassis frame.
-
8/22/2019 Amhara Water Works Enterprise Compliance
20/24
15. Wheel Base15.1 WheelsThe truck shall be equipped with single front and dual
rear, preferably trilex type wheels. All wheels and
rims shall be interchangeable and compatible with thetire size.
15.2 TireTires shall be manufacturers standard but heavy duty
on off highway type, with heavy duty tubes and flaps
shall be provided and shall be mounted on each wheel.
All tires shall be of the same size, type and load
range. A spare tire, tube and wheel shall be furnished
and shall be installed on a strong lockable carrier.
16. Mud GuardsThe tandem wheel base shall be grater than 1300mm.
17. Towing DeviceHeavy duty steel mudguards with rubber flaps, on both
sides of the tandem axle and on the rear size of the
front shall be furnished.
18. Towing DeviceThe vehicle shall be equipped with two towing device
hook ups at front and rear of the chassis mounted with
frame reinforcement as required for proper mounting.
19. Brake SystemThe service brakes shall be capable of controlling and
holding the full loaded truck on a 20% grade and shall be
consistently brining the fully loaded truck to a complete
stop within 12 meters from a speed of 32km/hr on hard,
-
8/22/2019 Amhara Water Works Enterprise Compliance
21/24
dry level road free from loose material.
19.1 Service BrakesService brakes shall be of the all wheel dual system
air type, with rake drums, located at each wheel, and
manually adjusted preferably be S-cam type brake
shoe; brake shall be of the air mechanical type. Brakediaphragm shall be mounted at each wheel in such
manner that no parts of the brake chamber or
diaphragm projects below the axles.
19.2 Parking BrakeThe parking brake shall be preferably hand/hydraulic
or pneumatic/operated mechanical type and capable
of holding the fully loaded truck in an either forward
or reverse on a 20% grade. Parking brakes should be
independent of the service brake. However, it may be
connected to the rear brake shoes through entirely
separated mechanical means.
19.3 Engine BrakeManufacturers standard an air operated engine brake
with an operating switch located within the drivers
reach shall be installed.
19.4 Warning DeviceAn audible and visual low air pressure warning device
shall be installed in the cab of the vehicle. The device
shall activate when the air pressure drops below the
limit specified by the manufacturer.
19.5 Under CoatingThe frame under structure of the truck and under
side of the hood shall be covered with suitable
undercoating to protect the vehicle against corrosion
and rust.
-
8/22/2019 Amhara Water Works Enterprise Compliance
22/24
20. ToolsSet of ordinary and special tools with lubrication fun;
filter wrenches. Wheel nut wrenches 20 tons hydraulic
jack shall be furnished with each machine in tool box.
Tools to supply should be listed.
21. Field Kits of Spare PartsThe following field kits of spare parts are to be
furnished with each machine and price shall be quoted
separately. Parts supplied shall be applicable to the unit
offered.
a) Two each set of all fan belts or other belts employedb) One each set of engine top overhaul gasketsc) One each set of all brake, air or fluid hosesd) Ten each sets of all oil filter elementse) Two each set of all hydraulic ram packing gaskets and
seal
f) One each set of all cooling hosesg) Three each set of all electrical fuses and bulbsh) Ten each set of all air cleaner elementsi) One each set of brake repair kitsj) Two each set of injector nozzles assy (enough for
complete engine)
k) One each set of all shock absorbersl) Two each sets of all brake liningm) One each set of air compressor repair kitsn) One each set of turbo charger repair kits
Please provide unit and total price of each of the items in
the field kits by indicating the description, individual part
number and each set required per each machine (quantity
per machine and total quantity to be supplied) in sequence
of the above.
-
8/22/2019 Amhara Water Works Enterprise Compliance
23/24
22. Essential Accessoriesa) Radiator guardb) Transmission guardc) Two front hooksd) Per cleaner (air)e) Lockable fuel capf) Tire inflation device including connectors charging
hoses reaching to all wheels
g) Inflation pressure gaugeh) One each multi-purpose fire extinguisher located at
easy reach of the operator
i) One each drinking water container with tap havingnot less than 10 liters capacity shall be included in
the supply. Container shall be galvanized
steel/aluminum material/stainless steel.
III. Fundamental Requirements Note that the fundamental requirements of the technical specification are
shown in the table below having the reference number of the technical
specification and corresponding title or sub titles and respective essential
requirements from which the bids should not deviate.
The bid will be determined as substantially responsive only and if only itcomplies with all the fundamental requirements.
Ref.
No.
Description of Parameters Compliance
II. General Requirements
Warranty
5 The warranty period shall be 12 months or 50,000km
whichever comes first from the date of formal
delivery of the machine
7 After sales service facility
Refer Item No. 7 of general specification
requirement
IV.Technical Requirement2 Engine
2.4 Horse Power
The engine shall deliver a minimum of 480 BHP
according to SAE J1349 net at rated RPM
-
8/22/2019 Amhara Water Works Enterprise Compliance
24/24
13 Chassis Frame
Ground Clearance
13.1 The ground clearance shall be a minimum of 500mm
when the vehicle is fully loaded and no other part of
the axle or other components shall protrude below
this clearance.
14 Dump body and tipping attachments
14.1 The dump body shall have a minimum of 20m3 at
struck when handling upto 1600kg/m3 material
density