Alveo U50 Data Center Accelerator Card Installation Guide

Alveo U50 Data CenterAccelerator Card InstallationGuide

UG1370 (v1.8) October 28, 2021

Xilinx is creating an environment where employees, customers, andpartners feel welcome and included. To that end, we’re removing non-inclusive language from our products and related collateral. We’velaunched an internal initiative to remove language that could excludepeople or reinforce historical biases, including terms embedded in oursoftware and IPs. You may still find examples of non-inclusivelanguage in our older products as we work to make these changes andalign with evolving industry standards. Follow this link for moreinformation.

https://www.xilinx.com

https://www.xilinx.com/content/dam/xilinx/publications/about/Inclusive-terminology.pdf

Revision HistoryThe following table shows the revision history for this document.

Section Revision Summary10/28/2021 Version 1.8

General Updates Removed U50DD related information.

Card Features Updated format and information.

XRT and Deployment Platform Installation Procedures onRedHat and CentOS

Updated installation steps for 2021.1 update.

XRT and Deployment Platform Installation Procedures onUbuntu

Updated installation steps for 2021.1 update.

Chapter 7: Troubleshooting Updated to direct users to more detailed troubleshootingand known issues content located in the Alveo Card DebugGuide and AR71752.

12/09/2020 Version 1.7

Chapter 1: Introduction Updated description for latest tools version.

Minimum System Requirements Updated supported operating system.


Updated installation procedure.


Updated installation procedure.

xbutil validate Removed note about XRT installation on Ubuntu.

Known Issues Updated to remove a known issue about XRT installation.

Generating the xbmgmt flash --update Command Updated output log.

Appendix A: Regulatory and Compliance Information Added appendix.

06/04/2020 Version 1.6

Chapter 1: Introduction Updated the information.

Card Features Added new section.

Card Interfaces and Details Added a caution.

Known Issues • Added a known issue about installing the U50 carddeployment package.

• Added a known issue about downgrading to a betaplatform.

Downgrading Packages Added information about downgrading to a beta platform.

02/27/2020 Version 1.5


Replaced steps 4, 6, 7, 8, and 9 to document the newinstallation steps for U50. Replaced all mentions of zip fileswith tar.gz.


Replaced steps 1, 2, 3, and the log file of step 6 to documentthe new installation steps for U50. Replaced all mentions ofzip files with tar.gz.

Running lspci Revised log file in step 2.

Running xbmgmt flash --scan Revised output, platform, and ID information in step 1.

Revision History

UG1370 (v1.8) October 28, 2021 www.xilinx.comAlveo U50 Data Center Accelerator Card Installation Guide 2Send Feedback

https://xilinx.github.io/Alveo-Cards/master/debugging/build/html/README.html


https://www.xilinx.com/support/answers/71752.html


https://www.xilinx.com/about/feedback/document-feedback.html?docType=User_Guides&docId=UG1370&Title=Alveo%20U50%20Data%20Center%20Accelerator%20Card%20Installation%20Guide&releaseVersion=1.8&docPage=2

Section Revision SummaryUpgrading Packages Updated step 1 to include a link to chapter 4; removed steps

2-6.

01/07/2020 Version 1.4

Installing the Card Updated to add notes about UL Listed Servers and cardhandling.

12/18/2019 Version 1.3

General Updated output logs.

Qualified Servers Updated the section and provided the web link to thequalified servers information.


Added a note about XRT installation.

10/31/2019 Version 1.2

General Updated to the Vitis™ unified software platform throughout.Updated outputs throughout the document.

Chapter 4: Installing the Deployment Software Replaced xbutil command with the new xbmgmtcommand for card flashing. Updated output logs.

Running xbmgmt flash --scan Replaced xbutil command with the new xbmgmtcommand when scanning card. Updated output logs.

Known Issues Added a link to Xilinx Answer Record 72766.Added a known issue.

Changing XRT and Target Platform Versions Replaced xbutil command with the new xbmgmtcommand for card flashing. Updated output logs.

09/18/2019 Version 1.1

General updates Updated sample outputs.

Card Interfaces and Details Added card interface related information and updatedimages.

Known Issues Included a link to Xilinx Answer Record 71752.Added information about power.

08/05/2019 Version 1.0

Initial release N/A

Revision History




Table of ContentsRevision History...............................................................................................................2

Chapter 1: Introduction.............................................................................................. 6

Chapter 2: Accelerator Card Overview............................................................... 7Card Features...............................................................................................................................7Minimum System Requirements............................................................................................... 8Qualified Servers......................................................................................................................... 8Card Interfaces and Details........................................................................................................8

Chapter 3: Card Installation Procedures......................................................... 10Safety Instructions.................................................................................................................... 10Before You Begin.......................................................................................................................12Installing the Card.....................................................................................................................13

Chapter 4: Installing the Deployment Software......................................... 15XRT and Deployment Platform Installation Procedures on RedHat and CentOS............. 16XRT and Deployment Platform Installation Procedures on Ubuntu...................................18

Chapter 5: Card Bring-Up and Validation........................................................21Environment Setup................................................................................................................... 21Running lspci............................................................................................................................. 22Confirm Firmware Installation ................................................................................................22Card Validation.......................................................................................................................... 23

Chapter 6: Next Steps.................................................................................................25

Chapter 7: Troubleshooting.................................................................................... 26

Appendix A: Regulatory and Compliance Information........................... 27Safety Compliance.....................................................................................................................27EMC Compliance........................................................................................................................27CE Directives.............................................................................................................................. 28




CE Standards..............................................................................................................................28Other Compliance Statements................................................................................................ 29Compliance Markings............................................................................................................... 32

Appendix B: Additional Resources and Legal Notices............................. 34Xilinx Resources.........................................................................................................................34Documentation Navigator and Design Hubs.........................................................................34References..................................................................................................................................35Please Read: Important Legal Notices................................................................................... 36




Chapter 1

IntroductionThis document provides hardware and software installation procedures for the half-height, half-length Xilinx® Alveo™ U50 data center accelerator card and applies to XRT 2021.1 and later. Forinstallation procedures using previous XRT versions, see v1.7 of Alveo U50 Data CenterAccelerator Card Installation Guide (UG1370).

If you encounter any issues during installation, see Chapter 7: Troubleshooting. For Alveo DataCenter accelerator card known issues and general information, see AR71752.

Different system configurations are available for running, developing, and debugging applicationson your Alveo accelerator cards:

• Running Applications: To configure a system to run accelerated applications, install an Alveocard into a system as described in Chapter 3: Card Installation Procedures along with therequired deployment software to support running applications as described in Chapter 4:Installing the Deployment Software.

• Developing Applications: To develop FPGA accelerated applications, it is necessary to installboth the deployment software and the development software. Development softwareinstallation, described in Chapter 6: Next Steps, consists of installing both a developmenttarget platform and the Vitis™ environment. This configuration does not have an Alveo cardinstalled and is used for development along with debugging in emulation modes.

• Running, Developing, and Debugging Applications: By installing the Alveo card along withboth the deployment and development software on a single machine, you can configure asystem for developing and running accelerated applications. With the card installed,developers can debug applications in both emulation modes and on the hardware.

Chapter 1: Introduction


https://www.xilinx.com/support/documentation/boards_and_kits/accelerator-cards/1_7/ug1370-u50-installation.pdf




Chapter 2

Accelerator Card Overview

Card FeaturesThe Alveo U50 data center accelerator card is PCIe® Gen3 x16 compliant and Gen4 x8compatible featuring the Xilinx 16 nm UltraScale+™ technology. It features 8 GB HBM to providehigh-performance, adaptable acceleration for memory-bound, compute-intensive applicationsincluding database, analytics, and machine learning inference.

The Alveo U50 accelerator card features are as follows.

Table 1: Alveo U50 Features

Card Component Alveo U50FPGA UltraScale+™ XCU50 FPGA

HBM 8 GB - two 4 gigabyte (GB) HBM memory stacks

Split into 32 256 MB channels

Network Interface 1x QSFP28

Supporting 100 GbE, 40 GbE, or 4x10/25 GbE

PCIe 16-lane PCI Express

PCIe Integrated Endpoint block connectivity

Gen1, 2, or 3 up to x16, Gen4 x8

Single or dual Gen4 x8

I2C Bus ✓Status LEDs ✓Power Management Power management with system management bus (SMBus)

voltage, current, and temperature monitoring

Electrical Design Power 75W PCIe slot functional with PCIe slot power only

Configuration Options 1 gigabit (Gb) Quad Serial Peripheral Interface (SPI) flashmemory

UltraScale+ device configurable over USB/JTAG and QuadSPI configuration flash memory

UART UART access through the maintenance connector

Chapter 2: Accelerator Card Overview




Note: The Alveo U50 card has separate power rails for FPGA fabric and HBM memory. Developers mustensure their designs do not draw too much power for each rail. The HBM rail is a 10W rail, and may limitHBM performance (see AR75222). For details on how to monitor power and temperature, see MonitorCard Power and Temperature.

Minimum System RequirementsThe minimum system requirements for running the Alveo™ U50 Data Center accelerator cardsare listed in the following table.

Table 2: Minimum System Requirements

Component RequirementMotherboard PCI Express® 3.0-compliant with one x16 slot.

System Power Supply 75W via PCI Express slot connection.

Operating System For the latest OS support see the Xilinx Runtime (XRT) Release Notes.

System Memory For deployment installations, a minimum of 16 GB plus application memoryrequirements is required.For development installations, a minimum of 64 GB of system memory isrequired, but 80 GB is recommended.

Internet Connection Required for downloading drivers and utilities.

Hard disk space Satisfy the minimum system requirements for your operating system.

Licensing None required for application deployment.For the application development environment, see Vitis Unified SoftwarePlatform Documentation: Application Acceleration Development (UG1393).

For details on the acceptable environmental conditions, see Alveo U50 Data Center AcceleratorCards Data Sheet (DS965).

Qualified ServersThe Xilinx Qualified Servers Catalog provides a list of servers that Alveo cards are fully qualified.

Card Interfaces and DetailsThe Alveo™ U50 accelerator card is available in a passive cooling configuration and is designedfor installation into a data center server where controlled air flow provides direct cooling to thecard. The card includes the following interfaces.



https://support.xilinx.com/s/article/75222?language=en_US

https://xilinx.github.io/Alveo-Cards/master/debugging/build/html/docs/common-steps.html#monitor-card-power-and-temperature

https://xilinx.github.io/Alveo-Cards/master/debugging/build/html/docs/common-steps.html#monitor-card-power-and-temperature

https://www.xilinx.com/support/documentation-navigation/see-all-versions.html?xlnxproducttypes=Design%20Tools&xlnxdocumentid=UG1451

https://www.xilinx.com/cgi-bin/docs/rdoc?v=latest;d=ug1393-vitis-application-acceleration.pdf

https://www.xilinx.com/cgi-bin/docs/ndoc?t=data_sheets;d=ds965-u50.pdf

https://www.xilinx.com/products/boards-and-kits/alveo/qualified-servers.html



• A PCI Express® card connector

• One QSFP28 connector supporting 100 GbE, 40 GbE, or 4x10/25 GbE

• Maintenance Connector

Used to program the card in RTL flow through the programming cable. For more informationsee the Alveo Programming Cable User Guide (UG1377).

Figure 1: Alveo U50 PQ Card with Half-Height Bracket

CAUTION! Alveo accelerator cards are designed to be installed into a data center server, where controlledair flow provides direct cooling. If the cooling enclosure is removed from the card and the card is powered-up, external fan cooling airflow MUST be applied to prevent over-temperature shut-down and possibledamage to the card electronics. Removing the cooling enclosure voids the board warranty.

For card specifications, dimensions, list of card features, and block diagram, see Alveo U50 DataCenter Accelerator Cards Data Sheet (DS965).



https://www.xilinx.com/cgi-bin/docs/bkdoc?k=accelerator-cards;d=ug1377-alveo-programming-cable-user-guide.pdf




Chapter 3

Card Installation ProceduresTo reduce the risk of fire, electric shock, or injury, always follow basic safety precautions.

CAUTION! You must always use an ESD strap or other antistatic device when handling hardware.

ATTENTION! Il est fortement recommandé d'utiliser un bracelet ESD ou autres dispositifs antistatiques.

VORSICHT! Beim Umgang mit Hardware müssen sie immer ein Erdungs Armband oder ein anderesantistatisches Gerät verwenden.

Safety InstructionsSafety Information

To ensure your personal safety and the safety of your equipment:

• Keep your work area and the computer/server clean and clear of debris.

• Before opening the computer/system cover, unplug the power cord.

Dispositif de Sécurité

Pour assurer votre sécurité personnelle et la sécurité de votre équipement:

• Maintenez votre zone de travail et l'ordinateur/serveur propre et dégagé de débris.

• Avant d'ouvrir le capot de l'ordinateur/système, débranchez le cordon d'alimentation.

Sicherheitsinformation

Um ihre persönliche Sicherheit und die Sicherheit ihrer Ausrüstung zu gewährleisten:

• Halten sie ihren Arbeitsbereich und den Computer / Server sauber und frei von Ablagerungen.

• Ziehen sie vor dem Öffnen der Computer / Systemabdeckung das Netzkabel ab.

Chapter 3: Card Installation Procedures




Electrostatic Discharge Caution

Electrostatic discharge (ESD) can damage electronic components when they are improperlyhandled, and can result in total or intermittent failures. Always follow ESD-prevention procedureswhen removing and replacing components.

To prevent ESD damage:

• Use an ESD wrist or ankle strap and ensure that it makes skin contact. Connect the equipmentend of the strap to an unpainted metal surface on the chassis.

• Avoid touching the card against your clothing. The wrist strap protects components from ESDon the body only.

• Handle the card by its bracket or edges only. Avoid touching the printed circuit board or theconnectors.

• Put the card down only on an antistatic surface such as the bag supplied in your kit.

• If you are returning the card to Xilinx Product Support, place it back in its antistatic bagimmediately.

Attention aux Décharge Électrostatique (ESD)

L'ESD peut endommager les composants électroniques lorsqu'ils sont mal manipulés, et peutentraîner des défaillances totales ou intermittentes. Suivez toujours les procédures de préventioncontre les ESD lors du retrait et remplacement des composants.

Pour prévenir les dommages dus aux ESD:

• Utilisez une sangle de poignet ou de cheville anti-ESD et assurez-vous qu'elle est en contactavec la peau. Branchez l'extrémité du cable de la sangle à une surface métallique non peintedu châssis et a la masse.

• Évitez de mettre en contact la carte de circuit imprimé ou les connecteurs avec vos vêtements.La sangle de poignet protège la carte ou connecteurs contre les ESD du corps seulement.

• Manipulez la carte uniquement par son support ou par ses bords. Évitez de toucher la carte decircuit imprimé ou les connecteurs.

• Ne posez la carte de circuit imprimé ou les connecteurs que sur une surface antistatique telleque le sac anti-statique fourni avec la carte.

• Si vous retournez la carte a Xilinx, remettez-la dans son sac antistatique immédiatement.

Vorsicht Elektrostatische Entladung

Elektrostatische Entladung (ESD) kann elektronische Bauteile beschädigen, wenn sieunsachgemäß behandelt werden, und es kann zu totalen oder zeitweiligen Ausfällen kommen.Befolgen sie beim Entfernen und Austauschen von Komponenten stets die ESD-Schutzmaßnahmen.





So verhindern sie ESD-Schäden:

• Verwenden sie einen ESD-Handgelenk-oder Knöchelriemen und stellen sie sicher, dass erHautkontakt hat. Verbinden sie das Ende des Riemens mit einer unlackierten Metalloberflächeam Gehäuse.

• Berühren sie die Karte nicht mit ihrer Kleidung. Der Riemen schützt Komponenten nur vorESD am Körper.

• Fassen sie die Karte nur an der Halterung oder an den Kanten an. Berühren sie nicht dieLeiterplatte oder die Anschlüsse.

• Legen sie die Karte nur auf einer antistatischen Oberfläche ab, z.B. dem antistatischen Beutelder mit dem Kit mitgeliefert wurde.

• Wenn sie die Karte an den Xilinx Product Support zurücksenden, legen Sie sie bitte sofortwieder in den antistatischen Beutel.

Before You BeginIMPORTANT! Alveo™ cards are delicate and sensitive electronic devices; equipment is to be installed by aqualified technician only. This equipment is intended for installation in a Restricted Access Location.

IMPORTANT! Les cartes Alveo™ sont des appareils électronique sensibles et fragiles; l'équipement doitêtre installé par un technicien certifié seulement. Cet équipement est destiné à être installé dans un lieud'accès restreint.

WICHTIG! Die Karten Alveo™ sind sensible und empfindliche elektronische Geräte. Das Gerät darf nurvon einem qualifizierten Techniker installiert werden. Dieses Gerät ist für die Installation an einem Ort mitbegrenztem Zugang vorgesehen.

• Verify that the minimum card space is available to install your card. Card specifications anddimensions can be found in Alveo U50 Data Center Accelerator Cards Data Sheet (DS965).

• Determine if a half or full height bracket is necessary for the installation. If the bracket needsto be changed, do this before following the installation steps.

• Check for card compatibility with the system. Also check for proper system requirements suchas power, bus type, and physical dimensions to support the card.

Related Information

Minimum System RequirementsQualified ServersReplacing the Bracket






Replacing the BracketThe Alveo U50 card can be used with either a full-height or half-height bracket. Depending onyour system, it may be necessary to switch between the full and half-height bracket on the card.The bracket is secured to the card with four screws, as shown in the figure below. To replace thebracket, follow the instructions below.

1. Remove screws 1 and 2 from the card.

2. Remove screws 3 and 4 from the card.

3. Remove the bracket from the card.

4. Place the new bracket on the card and align it with the card's connectors and screw locations.

5. Replace screws 1 and 2 on the new bracket.

6. Replace screws 3 and 4 on the new bracket.

Figure 2: Screw Locations on Bracket

1 2 3 4X25852-101221

Installing the CardThe following procedure is a guide for the Xilinx® Alveo™ U50 Data Center accelerator cardinstallation. Consult your computer documentation for additional information.





Note: For use with UL Listed Servers or ITE.

If you encounter any issues during installation, see Chapter 7: Troubleshooting.

1. Shut down the host computer and unplug the power cord.

2. Open your computer by removing the casing.

3. If necessary, remove the adjacent PCIe® slot cover corresponding to the PCIe slot in whichyou are installing the Alveo card.

4. Plug the Alveo card into the PCIe x16 slot on the motherboard.

5. Re-install the computer casing.

6. Connect the power cord and turn on the computer.

WARNING! Do not power-on a passively cooled card without adequate forced airflow across the cardwith proper air flow direction, otherwise the card can be damaged. This card can heat up after use inthe server. Use caution when handling. For more information, see Alveo U50 Data Center AcceleratorCards Data Sheet (DS965).

7. To verify that the device has been installed correctly, enter the following Linux command inthe terminal:

$ sudo lspci -vd 10ee:

If the card is successfully installed and found by the operating system, a message similar tothe one below will be displayed.

This is a sample output for an installed Alveo U50 card:

65:00.0 Processing accelerators: Xilinx Corporation Device D020 Subsystem: Xilinx Corporation Device 000e Flags: bus master, fast devsel, latency 0, IRQ 135 Memory at 38bffc000000 (64-bit, prefetchable) [size=32M] Memory at 38bffe000000 (64-bit, prefetchable) [size=128K] Capabilities: [40] Power Management version 3 Capabilities: [48] MSI: Enable- Count=1/1 Maskable- 64bit+ Capabilities: [70] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting Capabilities: [1c0] #19 Capabilities: [1f0] Virtual Channel Capabilities: [e00] Access Control Services Kernel driver in use: xclmgmt Kernel modules: xclmgmt

Note: If this card has previously been installed, the lspci output will be similar to the one shown in Running lspci.

If you do not see a similar message, see Chapter 7: Troubleshooting.






Chapter 4

Installing the Deployment SoftwareThis chapter details the procedures for installing deployment software on RedHat/CentOS andUbuntu operating systems. All software installations use standard Linux RPM and Linux DEBpackages and require root access.

The deployment software consists of the following software packages:

• Xilinx® runtime (XRT): XRT provides the libraries and drivers for an application to run onAlveo™ cards and also includes xbutil and xbmgmt utilities. Utility command line help canalways be obtained using the --help option.

• Deployment platform: The deployment platform provides the base firmware needed to runpre-compiled applications. It cannot be used to compile or create new applications. To createnew applications, install the development software detailed in Chapter 6: Next Steps. Whileyou can also install the development software on a machine with an installed card, doing so isnot necessary to run applications.

All installation packages can be downloaded from the Getting Started tab of the respective Alveocard landing page:

• Alveo U50 Product Page

If you encounter any issues during installation, see Chapter 7: Troubleshooting. For known issuesand general information, see AR71752.

IMPORTANT! Root access is required for all software and firmware installations.

IMPORTANT! L'accès Root est requis pour toutes les installations logicielles et firmware.

WICHTIG! Root-Zugriff ist für alle Software- und Firmware-Installationen erforderlich.

Chapter 4: Installing the Deployment Software


https://xilinx.github.io/XRT/master/html/xbutil.html

https://xilinx.github.io/XRT/master/html/xbmgmt.html

https://www.xilinx.com/products/boards-and-kits/u50.html




XRT and Deployment Platform InstallationProcedures on RedHat and CentOS

Use the following steps to download and install the XRT and deployment platform using a .rpminstallation package.

For details on upgrading or downgrading the XRT and deployment platform, see Changing XRTand Target Platform Versions .

1. XRT installation requires Extra Packages for Enterprise Linux (EPEL) and a related repository.If not already installed, install EPEL on your system by following the steps provided in XRTInstallation.

2. Run the following commands to install kernel headers and kernel development packages.Ensure that uname is surrounded by backticks ( `) and not single quotes (').

$ sudo yum install kernel-headers-`uname -r` $ sudo yum install kernel-devel-`uname -r`

3. After the previous command completes, warm boot your machine.

4. From the Getting Started tab of the Alveo U50 Product page, use the selection tool to displayand download the Xilinx® runtime (XRT) and deployment target platform installationpackages.

Download the packages by clicking on the displayed package names.

5. Install the XRT installation package by running the following command from within thedirectory where the installation packages reside. <version> is the latter part of theinstallation package file name.

$ sudo yum install ./xrt_<version>.rpm

This will install the XRT and its necessary dependencies. Follow the instructions whenprompted throughout the installation.

6. Unpack the deployment target platform tar.gz file into a single directory. The location ofthe directory is not important, however the directory should not contain any other files.

7. Install the deployment packages. From within the directory where the installation packageswere unpacked, run the following command. This will install all deployment packages.

sudo yum install ./*.rpm

8. Flash the platform firmware on the card. After installing the deployment packages in theprevious step, the following message is displayed:

Partition package installed successfully.Please flash card manually by running below command:$ sudo /opt/xilinx/xrt/bin/xbmgmt flash --update --shell <shell_name>



https://xilinx.github.io/Alveo-Cards/master/debugging/build/html/docs/modifying-xrt-platform.html


https://xilinx.github.io/XRT/master/html/install.html#install-xrt-pre-requests-on-deployment-server


https://www.xilinx.com/products/boards-and-kits/alveo/u50.html#gettingStarted



With XRT 2021.1 or greater, it is necessary to use the following new command to flash thecard rather than the one displayed in the above message. It assumes only one deploymentplatform is installed on the card. If more than one platform is installed the --image optionneeds to be added. See xbmgmt documentation for details.

$ sudo /opt/xilinx/xrt/bin/xbmgmt program --base --device <management BDF>

Where management BDF is the card to be programmed. See Displaying Card BDF Values toobtain the device management BDF.

Flashing can take several minutes.

IMPORTANT! Do not enter Ctrl + c in the terminal while the firmware is flashing as this can cause thecard to become inoperable.

IMPORTANT! N'entrez pas Ctrl + c dans le terminal lorsque le micrologiciel clignote, car cela pourraitrendre la carte inutilisable.

WICHTIG! Geben Sie im Terminal nicht Strg + c ein, während die Firmware blinkt, da dies dazu führenkann, dass die Karte nicht mehr funktioniert.

IMPORTANT! If you have multiple cards installed in the system, you must run the above xbmgmtprogram command separately for each card.

A message similar to the following will be displayed after successfully flashing the card:

1 device(s) flashed successfully.****************************************************Cold reboot machine to load the new image on device(s).****************************************************

If the card has been flashed with the current platform firmware, you will see a messagesimilar to the following.

Device(s) up-to-date and do not need to be flashed.

9. Cold boot the machine to load the new firmware image on the FPGA.

IMPORTANT! Be sure to fully power off the machine and then power it on again. The image will notboot from flash if the machine is only rebooted.

IMPORTANT! Assurez-vous d'éteindre complètement la machine, puis de la rallumer. L'image flash nedémarrera pas si la machine n'est pas redémarrée.

WICHTIG! Schalten Sie das Gerät vollständig aus und wieder ein. Das Image startet nicht von Flash,wenn der Computer nur neu gestartet wird.

10. Update the SC firmware on the card. Run the following command to update the SC firmwareon the card. It is the identical command used to flash the platform firmware on the card.





https://xilinx.github.io/Alveo-Cards/master/debugging/build/html/docs/common-steps.html#displaying-card-bdf-values



Where management BDF is the card requiring SC firmware update. See Displaying Card BDFValues to obtain the device management BDF.

Updating the SC firmware can take several minutes.

IMPORTANT! If you have multiple cards installed in the system, you must run the above xbmgmtprogram command separately for each card.

A message similar to the following will be displayed after a successful SC firmware update,where the device management BDF is given in square brackets.

Report [0000:af:00.0] : Successfully flashed1 device(s) flashed successfully.******************************************************************Warm reboot is required to recognize new SC image on the device.******************************************************************

If the card already has the current firmware, a message similar to the following is displayedand no additional installation steps are necessary.


11. Warm boot the system for XRT to recognize the new SC image.

The installation for deployment is now complete. Chapter 5: Card Bring-Up and Validationprovides steps to validate the card has been installed successfully.

XRT and Deployment Platform InstallationProcedures on Ubuntu

Use the following steps to download and install the XRT and deployment platform using a .debinstallation package.

For details on upgrading or downgrading the XRT and deployment platform, see Changing XRTand Target Platform Versions.

1. From the Getting Started tab of the Alveo U50 Product Page, use the selection tool to displaythe desired Xilinx runtime (XRT) and deployment target installation package.

Download the packages by clicking on the displayed package names.

2. Install the XRT installation package by running the following command from within thedirectory where the installation packages reside. <version> is the latter part of theinstallation package file name.

$ sudo apt install ./xrt_<version>.deb

This will install the XRT along with any necessary dependencies. Follow the instructionswhen prompted throughout the installation.







https://www.xilinx.com/products/boards-and-kits/alveo/u50.html#gettingStarted



3. Unpack the tar.gz file into a single directory. The location of the directory is not important,however the directory should not contain any other files.

4. Install the deployment packages. From within the directory where the installation packageswere unpacked, run the following command. This will install all deployment packages.

sudo apt install ./*.deb

5. Flash the platform firmware on the card. After installing the deployment packages in theprevious step, the following message is displayed:

Partition package installed successfully. Please flash card manually by running below command:$ sudo /opt/xilinx/xrt/bin/xbmgmt flash --update --shell <shell_name>

With XRT 2021.1 or greater, it is necessary to use the new command below to flash the cardrather than the one displayed in the above message. It assumes only one deploymentplatform is installed on the card. If more than one platform is installed the --image optionneeds to be added. See xbmgmt documentation for details.


Where management BDF is the card to be programmed. See Displaying Card BDF Values toobtain the device management BDF.

Flashing can take several minutes.

IMPORTANT! Do not enter Ctrl + c in the terminal while the firmware is flashing as this can cause thecard to become inoperable.

IMPORTANT! N'entrez pas Ctrl + c dans le terminal lorsque le micrologiciel clignote, car cela pourraitrendre la carte inutilisable.

WICHTIG! Geben Sie im Terminal nicht Strg + c ein, während die Firmware blinkt, da dies dazu führenkann, dass die Karte nicht mehr funktioniert.

IMPORTANT! If you have multiple cards installed in the system, you must run the above xbmgmtprogram  command separately for each card.

A message similar to the following will be displayed after successfully flashing the card:

1 device(s) flashed successfully.****************************************************Cold reboot machine to load the new image on device(s).****************************************************

If the card has been flashed with the current platform firmware, you will see a messagesimilar to the following.


6. Cold boot the machine to load the new firmware image on the FPGA.







IMPORTANT! Be sure to perform a cold boot to fully power off the machine and then power it onagain. The image will not boot from flash if the machine is only rebooted.

IMPORTANT! Initier un démarrage a froid en appuyant sur le bouton d’alimentation de la machine,puis rallumer la machine. L’image flash ne démarrera pas sans un démarrage a froid.

WICHTIG! Führen Sie einen Kaltstart aus, indem Sie das Gerät vollständig aus und wiedereinschalten. Das Image startet nicht von Flash, wenn der Computer nur neu gestartet wird.

7. Update the SC firmware on the card. Run the following command to update the SC firmwareon the card. It is the identical command used to flash the platform firmware on the card.


Where management BDF is the card requiring SC firmware update. See Displaying Card BDFValues to obtain the device management BDF.

Updating the SC firmware can take several minutes.

IMPORTANT! If you have multiple cards installed in the system, you must run the above xbmgmtprogram  command separately for each card.

A message similar to the following will be displayed after a successful SC firmware update,where the device management BDF is given in square brackets.

Report [0000:af:00.0] : Successfully flashed

1 device(s) flashed successfully.******************************************************************Warm reboot is required to recognize new SC image on the device.******************************************************************

If the card already has the current firmware, a message similar to the following is displayedand no additional installation steps are necessary.


8. Warm boot the system for XRT to recognize the new SC image.

The installation for deployment is now complete. Chapter 5: Card Bring-Up and Validationprovides steps to validate the card has been installed successfully.







Chapter 5

Card Bring-Up and ValidationAfter installing the XRT and deployment platform, the card installation can be verified using thefollowing commands, which are explained in more detail below.

• lspci

• xbmgmt examine

• xbutil validate

The lspci Linux command is used to confirm the card is seen by the OS.

The additional commands are used to validate and identify the installed card(s) and reportadditional card details including memory, PCIe®, platform name, and system information. See xbutil and xbmgmt

Note: Utility command line help can always be obtained using the --help option.

Related Information

Installing the Card

Environment SetupSet the environment to use the utilities by running the following command. Note that thecommand is dependent on the command shell you are using.

Use the following command in csh shell:

$ source /opt/xilinx/xrt/setup.csh

Use the following command in bash shell:

$ source /opt/xilinx/xrt/setup.sh

Chapter 5: Card Bring-Up and Validation






Running lspci1. Enter the following command:

$ sudo lspci -vd 10ee:

2. If the card is successfully installed and found by the operating system, you will see a messagesimilar to the following. Note that for each card, there will be two physical functions found:one for management and one for user. See XRT and Vitis™ Platform Overview for additionaldetails.

65:00.0 Processing accelerators: Xilinx Corporation Device 5020 Subsystem: Xilinx Corporation Device 000e Flags: bus master, fast devsel, latency 0 Memory at 38bff2000000 (64-bit, prefetchable) [size=32M] Memory at 38bff4020000 (64-bit, prefetchable) [size=128K] Capabilities: [40] Power Management version 3 Capabilities: [60] MSI-X: Enable+ Count=32 Masked- Capabilities: [70] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting Capabilities: [1c0] #19 Capabilities: [e00] Access Control Services Capabilities: [e10] #15 Capabilities: [e80] Vendor Specific Information: ID=0020 Rev=0 Len=010 <?> Kernel driver in use: xclmgmt Kernel modules: xclmgmt65:00.1 Processing accelerators: Xilinx Corporation Device 5021 Subsystem: Xilinx Corporation Device 000e Flags: bus master, fast devsel, latency 0, IRQ 183 Memory at 38bff0000000 (64-bit, prefetchable) [size=32M] Memory at 38bff4000000 (64-bit, prefetchable) [size=128K] Memory at 38bfe0000000 (64-bit, prefetchable) [size=256M] Capabilities: [40] Power Management version 3 Capabilities: [60] MSI-X: Enable+ Count=32 Masked- Capabilities: [70] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting Capabilities: [e00] Access Control Services Capabilities: [e10] #15 Capabilities: [e80] Vendor Specific Information: ID=0020 Rev=0 Len=010 <?> Kernel driver in use: xocl Kernel modules: xocl

Confirm Firmware InstallationWhen a card has successfully been installed and the firmware has been updated, both entries forPlatform and SC version installed on the card and the system must match. If they do notmatch, the system will be unable to correctly run applications on your card.



https://xilinx.github.io/XRT/master/html/platforms.html



To confirm they match, run the following command and visually compare the 'Platform' and 'SCVersion' entries under Flashable partitions running on FPGA and Flashablepartitions installed in system match. See Displaying Card BDF Values to obtain thedevice management BDF.

$ sudo /opt/xilinx/xrt/bin/xbmgmt examine --device <management BDF>

In the following example output, the Platform (xilinx_u50_gen3x16_xdma_201920_3) and SCVersion (5.2.6) displayed under Flashable partitions running on FPGA andFlashable partitions installed in system both match.

------------------------------------------------------1/1 [0000:af:00.0] : xilinx_u50_gen3x16_xdma_201920_3------------------------------------------------------Flash properties Type : spi Serial Number : XFL13K1ZFSI3

Device properties Type : u50 Name : ALVEO U50 PQ Config Mode : 7 Max Power : 75W

Flashable partitions running on FPGA Platform : xilinx_u50_gen3x16_xdma_201920_3 SC Version : 5.2.6 Platform UUID : F465B0A3-AE8C-64F6-19BC-150384ACE69B Interface UUID : 862C7020-A250-293E-3203-6F19956669E5

Flashable partitions installed in system Platform : xilinx_u50_gen3x16_xdma_201920_3 SC Version : 5.2.6 Platform UUID : F465B0A3-AE8C-64F6-19BC-150384ACE69B Mac Address : 00:0A:35:0A:40:71 : 00:0A:35:0A:40:72 : 00:0A:35:0A:40:73 : 00:0A:35:0A:40:74

Card ValidationCard installation can be validated using the xbutil validate command. This commandperforms various tests and checks on the card including PCIe link status, SC version status,memory and bandwidth tests and auxiliary power connection where applicable. Full commanddetails can be found in xbutil documentation. Depending on the card tested, not all tests are validor may require the function to be enabled (i.e., Peer-2-Peer).

Use the following command to run the card validation test:

$ /opt/xilinx/xrt/bin/xbutil validate --device <user BDF>




https://xilinx.github.io/XRT/master/html/xbutil.html#xbutil-validate



where user BDF is the card to be validated. See Displaying Card BDF Values to obtain the userBDF value.

If the card was installed and validated successfully, a message similar to the following will bedisplayed. Review the Validation Summary section at the end of the output and confirm thedevice validated successfully. Additional validation details are displayed by appending the --verbose option to the command. See Card Validation within the Alveo Card Debug Guide forsupport.

Starting validation for 1 devices Validate Device : [0000:af:00.1] Platform : xilinx_u50_gen3x16_xdma_201920_3 SC Version : 5.2.6 Platform ID : 0x0----------------------------------------------------------------------------Test 1 [0000:af:00.1] : PCIE link Test Status : [PASSED]----------------------------------------------------------------------------Test 2 [0000:af:00.1] : SC version Test Status : [PASSED]----------------------------------------------------------------------------Test 3 [0000:af:00.1] : Verify kernel Test Status : [PASSED]----------------------------------------------------------------------------Test 4 [0000:af:00.1] : DMA Details : Host -> PCIe -> FPGA write bandwidth = 11904.208324 MB/s Host <- PCIe <- FPGA read bandwidth = 11400.578936 MB/s Test Status : [PASSED]----------------------------------------------------------------------------Test 5 [0000:af:00.1] : iops Details : IOPS: 37278 (hello) Test Status : [PASSED]----------------------------------------------------------------------------Test 6 [0000:af:00.1] : Bandwidth kernel Details : Maximum throughput: 43855 MB/s Test Status : [PASSED]----------------------------------------------------------------------------Test 7 [0000:af:00.1] : vcuValidation completed. Please run the command '--verbose' option for more details Validation Summary------------------1 device(s) evaluated1 device(s) validated successfully0 device(s) had exceptions during validation Validated successfully [1 device(s)] - [0000:af:00.1] : xilinx_u50_gen3x16_xdma_201920_3 Validation Exceptions [0 device(s)] Warnings produced during test [0 device(s)] (Note: The given test successfully validated)




https://xilinx.github.io/Alveo-Cards/master/debugging/build/html/docs/card-validation.html

https://xilinx.github.io/Alveo-Cards/master/debugging/README.html



Chapter 6

Next StepsWhat you have done so far allows you to deploy and run accelerated applications on yoursystem. Alveo™ Accelerated Solutions page provides information and links to available Xilinx andthird-party accelerated applications. These include video processing, financial computing,machine learning, and data analytics.

If you are an application developer who wants to develop and deliver accelerated applications,install the Vitis™ software platform. It allows you to develop, debug, and optimize acceleratedapplications for Alveo cards. Installation instructions can be found in Vitis Unified SoftwarePlatform Documentation: Application Acceleration Development (UG1393).

For an overview of developing accelerated applications with Alveo™ with accompanying guidedexamples, see Get Moving with Alveo: Acceleration Basics.

For complete details on the development flow and getting started in Vitis, see Vitis UnifiedSoftware Platform Documentation: Embedded Software Development (UG1400). For an introductionto Vitis methodology, see Vitis Unified Software Platform Documentation (UG1416).

Chapter 6: Next Steps


https://www.xilinx.com/products/acceleration-solutions.html

https://www.xilinx.com/cgi-bin/docs/rdoc?v=2021.2;d=ug1393-vitis-application-acceleration.pdf

https://developer.xilinx.com/en/articles/acceleration-basics.html

https://www.xilinx.com/cgi-bin/docs/rdoc?v=latest;d=ug1400-vitis-embedded.pdf

https://www.xilinx.com/cgi-bin/docs/rdoc?t=vitis+doc;v=latest



Chapter 7

TroubleshootingFor card installation support, debugging information, and known issues, see the Alveo CardDebug Guide.

For known issues and general information, see AR71752.

Chapter 7: Troubleshooting







Appendix A

Regulatory and ComplianceInformation

This product is designed and tested to conform to the European Union directives and standardsdescribed in this section.

Safety ComplianceThe following table shows the safety standards that apply to the Alveo™ U50 card.

Table 3: Safety Standards

Safety Standard Alveo U50UL 60950-1, 2nd Edition, 2014-10-14 (Information Technology Equipment - Safety - Part 1: GeneralRequirements)

✓

CSA C22.2 No. 60950-1-07, 2nd Edition, 2014-10-14 (Information Technology Equipment - Safety - Part1: General Requirements)

✓

EN 60950-1:2006+A11:2009+A1:2012+A12:2011+A2:2013 (European Union) ✓IEC 60950-1:2005 (2nd Edition); Am 1:2009 (International) ✓EU LVD Directive 2014/35/EC ✓IEC 62368-1:2014 (Second Edition) ✓

EMC ComplianceThe following tables show the EMC standards that apply to the Alveo U50 card.

Class A Products

Table 4: EMC Standards

Standard Alveo U50FCC Part 15 – Radiated & Conducted Emissions (USA) ✓CAN ICES-3(A)/NMB-3(A) – Radiated & Conducted Emissions (Canada) ✓

Appendix A: Regulatory and Compliance Information




Table 4: EMC Standards (cont'd)

Standard Alveo U50CISPR 32 – Radiated & Conducted Emissions (International) ✓EN55032: 2015 – Radiated & Conducted Emissions (European Union) ✓EN55024: 2010 +A1:2001+A2:2003 – Immunity (European Union) ✓EMC Directive 2014/30/EC ✓VCCI (Class A)– Radiated & Conducted Emissions (Japan) ✓CNS13438 – Radiated & Conducted Emissions (Taiwan) ✓CNS 15663 - RoHS (Taiwan) ✓AS/NZS CISPR 32 – Radiated and Conducted Emissions (Australia/New Zealand) ✓Article 58-2 of Radio Waves Act, Clause 3 (Korea) ✓

Regulatory Compliance MarkingsThe following table shows the product certification markings that are provided, when required,with the Alveo U50 card.

Table 5: Product Certification Markings

Product Certification Markings Alveo U50UL Listed Accessories Mark for the USA and Canada ✓CE mark ✓FCC markings ✓VCCI marking ✓Australian C-Tick mark ✓Korea MSIP mark ✓Taiwan BSMI mark ✓

CE Directives2014/35/EC, Low Voltage Directive (LVD)

2014/30/EC, Electromagnetic Compatibility (EMC) Directive

CE StandardsEN standards are maintained by the European Committee for Electrotechnical Standardization(CENELEC). IEC standards are maintained by the International Electrotechnical Commission (IEC).





Electromagnetic CompatibilityEN:55032:2015, Information Technology Equipment Radio Disturbance Characteristics – Limits andMethods of Measurement

EN:55024:2015, Information Technology Equipment Immunity Characteristics – Limits and Methodsof Measurement

This is a Class A product. In a domestic environment, this product can cause radio interference, inwhich case the user might be required to take adequate measures.

Other Compliance StatementsThe following sections only apply to Alveo U50 cards.

FCC Class A User InformationThe Class A products listed above comply with Part 15 of the FCC Rules. Operation is subject tothe following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that may causeundesired operation.

IMPORTANT! This equipment has been tested and found to comply with the limits for a Class Adigital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonableprotection against harmful interference when the equipment is operated in a commercial environment.This equipment generates, uses, and can radiate radio frequency energy and, if not installed and usedin accordance with the instructions, may cause harmful interference to radio communications.Operation of this equipment in a residential area is likely to cause harmful interference, in which casethe user will be required to correct the interference at his or her own expense.

IMPORTANT! Cet équipement a été testé et jugé conforme à la Class A digital device, conformémentà la règle 15 du standard FCC. Ces limites sont conçues pour fournir des protections contre desinterférences nuisibles lorsque l'équipement est utilisé dans un environnement commercial. Cetéquipement génère, utilise et peut émettre des énergies de radio-fréquence et, s'il n'est pas installé etutilisé conformément aux instructions, peut nuire aux communications radio. L'exploitation de cetéquipement dans une zone résidentielle est susceptible de causer des interférences nuisibles, auquelcas l'utilisateur peut être tenu de prendre des mesures adéquates à ses propres frais.





WICHTIG! Dieses Gerät wurde getestet und entspricht den Grenzwerten für digitale Geräte derKlasse A gemäß Teil 15 der FCC-Bestimmungen. Diese Grenzwerte bieten einen angemessenen Schutzgegen schädliche Interferenzen, wenn das Gerät in einer gewerblichen Umgebung betrieben wird.Dieses Gerät erzeugt und verwendet Hochfrequenzenergie und kann diese abstrahlen. Wenn es nichtgemäß den Anweisungen installiert und verwendet wird, kann dies Funkstörungen verursachen. DerBetrieb dieses Geräts in einem Wohngebiet kann schädliche Interferenzen verursachen. In diesem Fallmuss der Benutzer die Interferenz auf eigene Kosten beheben.

CAUTION! If the device is changed or modified without permission from Xilinx, the user may void hisor her authority to operate the equipment.

ATTENTION! Si l'appareil est modifié sans l'autorisation de Xilinx, l'utilisateur peut annuler son abilitéà utiliser l'équipement.

VORSICHT! Wenn das Gerät ohne Erlaubnis von Xilinx geändert wird, kann der Benutzer seineBerechtigung zum Betrieb des Geräts verlieren.

Canadian Compliance (Industry Canada)CAN ICES-3(A)/NMB-3(A)

VCCI Class A Statement

KCC Notice Class A (Republic of Korea Only)

BSMI Class A Notice (Taiwan)





Manufacturer Declaration European Community

Manufacturer Declaration

Xilinx declares that the equipment described in this document is in conformance with therequirements of the European Council Directive listed below:

• Low Voltage Directive 2014/35/EU

• EMC Directive 2014/30/EU

• RoHS 3 Directive 2011/65/EU, 2015/863

These products follow the provisions of the European Directive 2014/53/EU.

Dette produkt er i overensstemmelse med det europæiske direktiv 2014/53/EU.

Dit product is in navolging van de bepalingen van Europees Directief 2014/53/EU.

Tämä tuote noudattaa EU-direktiivin 2014/53/EU määräyksiä.

Ce produit est conforme aux exigences de la Directive Européenne 2014/53/EU.

Dieses Produkt entspricht den Bestimmungen der Europäischen Richtlinie 2014/53/EU.

Þessi vara stenst reglugerð Evrópska Efnahags Bandalagsins númer 2014/53/EU.

Questo prodotto è conforme alla Direttiva Europea 2014/53/EU.

Dette produktet er i henhold til bestemmelsene i det europeiske direktivet 2014/53/EU.

Este produto cumpre com as normas da Diretiva Européia 2014/53/EU.

Este producto cumple con las normas del Directivo Europeo 2014/53/EU.

Denna produkt har tillverkats i enlighet med EG-direktiv 2014/53/EU.

This declaration is based upon compliance of the Class A products listed above to the followingstandards:

EN 55032 (CISPR 32 Class A) RF Emissions Control.EN 55024:2010 (CISPR 24) Immunity to Electromagnetic Disturbance.





EN 60950-1:2006/A11:2009A1:2010/A12:2011 Information Technology Equipment- Safety-Part 1: General Requirements.EN 50581:2012 - Technical documentation for the assessment of electrical and electronicproducts with respect to the restriction of hazardous substances.

CAUTION! In a domestic environment, Class A products may cause radio interference, in which case theuser may be required to take adequate measures.

ATTENTION! Dans un environnement domestique, les produits de Classe A peuvent causer desinterférences radio, auquel cas l'utilisateur peut être tenu de prendre des mesures adéquates.

VORSICHT! In einer häuslichen Umgebung können Produkte der Klasse A Funkstörungen verursachen. Indiesem Fall muss der Benutzer möglicherweise geeignete Maßnahmen ergreifen.

Responsible Party

Xilinx, Inc.2100 Logic Drive, San Jose, CA 95124United States of AmericaPhone: (408) 559-7778

Compliance MarkingsIn August of 2005, the European Union (EU) implemented the EU Waste Electricaland Electronic Equipment (WEEE) Directive 2002/96/EC and later the WEEE RecastDirective 2012/19/EU. These directives require Producers of electronic andelectrical equipment (EEE) to manage and finance the collection, reuse, recyclingand to appropriately treat WEEE that the Producer places on the EU market afterAugust 13, 2005. The goal of this directive is to minimize the volume of electricaland electronic waste disposal and to encourage re-use and recycling at the endof life.Xilinx has met its national obligations to the EU WEEE Directive by registering inthose countries to which Xilinx is an importer. Xilinx has also elected to join WEEECompliance Schemes in some countries to help manage customer returns atend-of-life.If you have purchased Xilinx-branded electrical or electronic products in the EUand are intending to discard these products at the end of their useful life, pleasedo not dispose of them with your other household or municipal waste. Xilinx haslabeled its branded electronic products with the WEEE Symbol to alert ourcustomers that products bearing this label should not be disposed of in a landfillor with municipal or household waste in the EU.





This product complies with Directive 2002/95/EC on the restriction of hazardoussubstances (RoHS) in electrical and electronic equipment.

This product complies with CE Directives 2006/95/EC, Low Voltage Directive (LVD)and 2004/108/EC, Electromagnetic Compatibility (EMC) Directive.





Appendix B

Additional Resources and LegalNotices

Xilinx ResourcesFor support resources such as Answers, Documentation, Downloads, and Forums, see XilinxSupport.

Documentation Navigator and Design HubsXilinx® Documentation Navigator (DocNav) provides access to Xilinx documents, videos, andsupport resources, which you can filter and search to find information. To open DocNav:

• From the Vivado® IDE, select Help → Documentation and Tutorials.

• On Windows, select Start → All Programs → Xilinx Design Tools → DocNav.

• At the Linux command prompt, enter docnav.

Xilinx Design Hubs provide links to documentation organized by design tasks and other topics,which you can use to learn key concepts and address frequently asked questions. To access theDesign Hubs:

• In DocNav, click the Design Hubs View tab.

• On the Xilinx website, see the Design Hubs page.

Note: For more information on DocNav, see the Documentation Navigator page on the Xilinx website.

Appendix B: Additional Resources and Legal Notices


https://www.xilinx.com/support

https://www.xilinx.com/support

https://www.xilinx.com/cgi-bin/docs/ndoc?t=design+hubs

https://www.xilinx.com/cgi-bin/docs/rdoc?t=docnav



ReferencesVitis Documents

These documents provide supplemental material useful with this guide:

1. Vitis Unified Software Platform Documentation: Application Acceleration Development (UG1393)

2. Vitis Unified Software Platform Documentation (UG1416)

3. Vitis Unified Software Platform Documentation: Embedded Software Development (UG1400)

4. Vitis Application Acceleration Development Flow Tutorials (GitHub)

Alveo Documents

1. Alveo U50 Data Center Accelerator Cards Data Sheet (DS965)

2. Alveo Card Debug Guide (XD027)

3. Alveo Data Center Accelerator Card Platforms User Guide (UG1120)

4. Alveo Programming Cable User Guide (UG1377)

Additional Xilinx Resources

1. Alveo Data Center Accelerator Card - Known Issues and General Information (AR71752)

2. xbutil

3. xbmgmt

4. Xilinx Runtime for Alveo Data Center Accelerator Cards - Master Release Notes and Known Issues

5. Xilinx Runtime (XRT) Installation

6. Xilinx XRT Release Notes

7. Xilinx licensing website: https://www.xilinx.com/getproduct

8. Vitis Developer Zone: https://www.xilinx.com/products/design-tools/vitis/vitis-platform.html

9. Xilinx Community Forums: https://forums.xilinx.com

10. Xilinx Third-Party End User License Agreement

11. End-User License Agreement



https://www.xilinx.com/cgi-bin/docs/rdoc?v=2021.2;d=ug1393-vitis-application-acceleration.pdf

https://www.xilinx.com/cgi-bin/docs/rdoc?t=vitis+doc;v=latest

https://www.xilinx.com/cgi-bin/docs/rdoc?v=2021.2;d=ug1400-vitis-embedded.pdf

https://github.com/Xilinx/Vitis-Tutorials


https://xilinx.github.io/Alveo-Cards/master/debugging/README.html

https://www.xilinx.com/cgi-bin/docs/bkdoc?k=accelerator-cards;d=ug1120-alveo-platforms.pdf

https://www.xilinx.com/cgi-bin/docs/bkdoc?k=accelerator-cards;d=ug1377-alveo-programming-cable-user-guide.pdf




https://support.xilinx.com/s/article/71628


https://www.xilinx.com/support/documentation-navigation/see-all-versions.html?xlnxproducttypes=Design%20Tools&xlnxdocumentid=UG1451

https://www.xilinx.com/getproduct

https://www.xilinx.com/products/design-tools/vitis/vitis-platform.html

https://forums.xilinx.com

https://www.xilinx.com/cgi-bin/docs/rdoc?v=latest;d=ug763_tplg.pdf

https://www.xilinx.com/cgi-bin/docs/rdoc?v=latest;d=end-user-license-agreement.pdf



Please Read: Important Legal NoticesThe information disclosed to you hereunder (the "Materials") is provided solely for the selectionand use of Xilinx products. To the maximum extent permitted by applicable law: (1) Materials aremade available "AS IS" and with all faults, Xilinx hereby DISCLAIMS ALL WARRANTIES ANDCONDITIONS, EXPRESS, IMPLIED, OR STATUTORY, INCLUDING BUT NOT LIMITED TOWARRANTIES OF MERCHANTABILITY, NON-INFRINGEMENT, OR FITNESS FOR ANYPARTICULAR PURPOSE; and (2) Xilinx shall not be liable (whether in contract or tort, includingnegligence, or under any other theory of liability) for any loss or damage of any kind or naturerelated to, arising under, or in connection with, the Materials (including your use of theMaterials), including for any direct, indirect, special, incidental, or consequential loss or damage(including loss of data, profits, goodwill, or any type of loss or damage suffered as a result of anyaction brought by a third party) even if such damage or loss was reasonably foreseeable or Xilinxhad been advised of the possibility of the same. Xilinx assumes no obligation to correct anyerrors contained in the Materials or to notify you of updates to the Materials or to productspecifications. You may not reproduce, modify, distribute, or publicly display the Materialswithout prior written consent. Certain products are subject to the terms and conditions ofXilinx's limited warranty, please refer to Xilinx's Terms of Sale which can be viewed at https://www.xilinx.com/legal.htm#tos; IP cores may be subject to warranty and support terms containedin a license issued to you by Xilinx. Xilinx products are not designed or intended to be fail-safe orfor use in any application requiring fail-safe performance; you assume sole risk and liability foruse of Xilinx products in such critical applications, please refer to Xilinx's Terms of Sale which canbe viewed at https://www.xilinx.com/legal.htm#tos.

AUTOMOTIVE APPLICATIONS DISCLAIMER

AUTOMOTIVE PRODUCTS (IDENTIFIED AS "XA" IN THE PART NUMBER) ARE NOTWARRANTED FOR USE IN THE DEPLOYMENT OF AIRBAGS OR FOR USE IN APPLICATIONSTHAT AFFECT CONTROL OF A VEHICLE ("SAFETY APPLICATION") UNLESS THERE IS ASAFETY CONCEPT OR REDUNDANCY FEATURE CONSISTENT WITH THE ISO 26262AUTOMOTIVE SAFETY STANDARD ("SAFETY DESIGN"). CUSTOMER SHALL, PRIOR TO USINGOR DISTRIBUTING ANY SYSTEMS THAT INCORPORATE PRODUCTS, THOROUGHLY TESTSUCH SYSTEMS FOR SAFETY PURPOSES. USE OF PRODUCTS IN A SAFETY APPLICATIONWITHOUT A SAFETY DESIGN IS FULLY AT THE RISK OF CUSTOMER, SUBJECT ONLY TOAPPLICABLE LAWS AND REGULATIONS GOVERNING LIMITATIONS ON PRODUCTLIABILITY.



https://www.xilinx.com/legal.htm#tos





Copyright

© Copyright 2019-2021 Xilinx, Inc. Xilinx, the Xilinx logo, Alveo, Artix, Kintex, Kria, Spartan,Versal, Vitis, Virtex, Vivado, Zynq, and other designated brands included herein are trademarks ofXilinx in the United States and other countries. OpenCL and the OpenCL logo are trademarks ofApple Inc. used by permission by Khronos. PCI, PCIe, and PCI Express are trademarks of PCI-SIGand used under license. AMBA, AMBA Designer, Arm, ARM1176JZ-S, CoreSight, Cortex,PrimeCell, Mali, and MPCore are trademarks of Arm Limited in the EU and other countries. Allother trademarks are the property of their respective owners.





Alveo U50 Data Center Accelerator Card Installation Guide

Documents

Transcript of Alveo U50 Data Center Accelerator Card Installation Guide