ALUMINIUM SYSTEMS OVERVIEW

VERSION 1.0

1300 374 253 www.himmel.com.au

A SERIES 104

A Series 104 provides a central line glazing with numerous configurations and design options offering a complete partition system for plasterboard and glazing.

A Series 104 has the following features:

• Standard profile size of 104mm x 25mm, 104mm x 35mm or 104mm x 50mm• Standard wall size based on 64mm steel stud with one layer of 13mm Gyprock

plaster board on each side• Can accommodate glass thicknesses between 6mm and 13mm• Door thicknesses between 35mm - 45mm can be used• Shadowline details optional

GLASS OPTIONS

Partition frame design

Many partition systems have removable beads and adequate pocket depth to get both the edge cover and edge clearance required. However some systems with fixed pockets on two or more sides require “shuffle” glazing and the edge clearance must be increased to install the glass. As the edge cover must be less than half the rebate depth in this system, this often decreases the edge cover below the allowable limits of the glass thickness. As illustrated in Details 1 & 2 the glass size cannot be more than the sight size plus the depth of one rebate, less a glazing clearance of 2mm-4mm (dependent on glass thickness, type, frame straightness and squareness). When installed, this glass is then centred in the frame. Therefore an 18mm rebate will only allow a maximum edge cover of 7mm or 8mm (1⁄2 rebate depth minus 1⁄2 of clearance) with the maximum glass thickness derived from Table 1 (below).

Glass thickness (mm) Minimum edge cover Minimum edge clearance Total rebate depth (mm)

6 6 4 10

8 8 5 13

10 8 5 13

12 9 6 15

Table 1

HAS017-35AS104 SNAP IN DOORSTOP

UP TO 35MM DOORS

2.8M C/A: 1550573.6M C/A: 1699782.8M BLK: 1602283.6M BLK: 180884

A SERIES 104

A SERIES 104

HAS009100MM SKIRTING

2.8M C/A: 1032823.6M C/A: 1032982.8M BLK: 1087733.6M BLK: 160218

HAS009-150150MM SKIRTING

2.8M C/A: 1032833.6M C/A: 1032992.8M BLK: 1602193.6M BLK: 160220

HAS010AS104 HEAD/SILL TRACK

2.8M C/A: 1032783.6M C/A: 1816802.8M BLK: 1602223.6M BLK: 181682

HAS010-AAS104 HEAD TRACK

2.8M C/A: 1976133.6M C/A: 1976332.8M BLK: 1976323.6M BLK: 197635

HAS010-A-50AS104 HAS010-A-50 COC TRANSOM

2.8M C/A: 1816323.6M C/A: 1816852.8M BLK: 1816343.6M BLK: 181687

HAS010-RAS104 REBATED HEAD TRACK

2.8M C/A: 4532423.6M C/A: 4532472.8M BLK: 4532463.6M BLK: 453249

100 15

0

25

104

25

104 104

35

104

HAS010-SHAS104 SHADOWLINE HEADTRACK

2.8M C/A: 1550643.6M C/A: 1816952.8M BLK: 1828283.6M BLK: 181697

104

HAS011AS104 HAS011 FLUSH FILLER

2.8M C/A: 1550593.6M C/A: 1815912.8M BLK: 1602263.6M BLK: 181593

HAS011-JPAS104 FLAT TERMINATION CAP

2.8M C/A: 1815663.6M C/A: 181590

98

104

64

HAS011-SHAS104 JOINTING PLATE

2.8M C/A: 1815703.6M C/A: 181596

HAS012-MAPAS104 MULLION ADAPTOR

2.8M C/A: 1550613.6M C/A: 1808862.8M BLK: 1602253.6M BLK: 180882

HAS014-AAS104 DEEP POCKET MULLION

2.8M C/A: 1976463.6M C/A: 1976492.8M BLK: 1976483.6M BLK: 197651

HAS014FMAS104 FINNED MULLION

2.8M C/A: 1550673.6M C/A: 1699792.8M BLK: 1602243.6M BLK: 181730

15

104

25

104

25

104

64

HAS014-50FM AS104 FINNED MULLION

2.8M C/A:455353 3.6M C/A: 455356 2.8M BLK: 455355 3.6M BLK: 455358

104

HAS014-35FMAS104 FINNED MULLION

2.8M C/A: 1976403.6M C/A: 1976432.8M BLK: 1976423.6M BLK: 197645

35

104

HAS015-25FLMAS104 FINLESS MULLION

2.8M C/A: 1550623.6M C/A: 1625832.8M BLK: 1602233.6M BLK: 181690

HAS015-35FLMAS104 FINLESS MULLION

2.8M C/A: 1976523.6M C/A: 1976552.8M BLK: 1976543.6M BLK: 197657

HAS015-50FLMFINLESS MULLION

2.8M C/A: 155066 3.6M C/A: 1817212.8M BLK: 160231 3.6M BLK: 170030

HAS016AS104 GLAZING ADAPTOR

2.8M C/A: 1550603.6M C/A: 1816112.8M BLK: 1602333.6M BLK: 181612

104

25

104

35

104

50

104

HAS018-45AS104 SNAP IN DOORSTOP

UP TO 45MM DOORS

2.8M C/A: 1550553.6M C/A: 1810842.8M BLK: 1602273.6M BLK: 181085

HAS019-50BAAS104 GLAZING BASE

2.8M C/A: 155065 3.6M C/A: 181717 2.8M BLK: 160232 3.6M BLK: 170031

50

HAS017-40AS104 SNAP IN DOORSTOP

UP TO 45MM DOORS

2.8M C/A: 1815163.6M C/A: 1815372.8M BLK: 1815183.6M BLK: 181539

85

25

HAS019BAAS104 GLAZING BASE

2.8M C/A: 1550633.6M C/A: 1625842.8M BLK: 1602293.6M BLK: 180883

HAS019-35BAAS104 GLAZING BASE

2.8M C/A: 1976583.6M C/A: 1976612.8M BLK: 1976603.6M BLK: 197663

85

35

HAS020-50AS104 GLAZING BEAD

2.8M C/A: 4553593.6M C/A: 4553622.8M BLK: 4553613.6M BLK: 455364

50

HAS020AS104 GLAZING BEAD

2.8M C/A: 1976643.6M C/A: 1976672.8M BLK: 1976663.6M BLK: 197669

HAS020-35AS104 GLAZING BEAD

2.8M C/A: 1976703.6M C/A: 1976732.8M BLK: 1976723.6M BLK: 197675

44

25

44

35

104

36

HAS021-AAS104 GLAZING TRANSOM

2.8M C/A: 4532603.6M C/A: 4532632.8M BLK: 4532623.6M BLK: 453265

101

HAS021-BAS104 GLAZING TRANSOM

2.8M C/A: 1976763.6M C/A: 1976792.8M BLK: 1976783.6M BLK: 197681

HAS022AS104 GLAZING BEAD

2.8M C/A: 1550563.6M C/A: 1625972.8M BLK: 1602303.6M BLK: 170032

44

HAS023AS104 FILLTER PLATE

2.8M C/A: 1550073.6M C/A: 1815102.8M BLK: 1815023.6M BLK: 181512

HAS024-CPAS104 CORNER POST

2.8M C/A: 1550703.6M C/A: 1817492.8M BLK: 1602343.6M BLK: 181751

HAS024-FCPAS104 FLUSH CORNER POST

2.8M C/A: 1976823.6M C/A: 1976852.8M BLK: 1976843.6M BLK: 197687

104

104

111

111

104

50

A SERIES 132

A Series 132 provides a central line glazing with numerous configurations and design options, offering a complete partition system for plasterboard and glazing.

A Series 132 has the following features:

• Standard profile size of 132mm x 25mm, 132mm x 35mm, 132mm x 50mm• Standard wall size based around 92mm steel stud with one layer of 13mm

Gyprock plaster board on each side• Can accommodate glass thicknesses between 6mm and 13mm• Door thicknesses between 35mm and 45mm can be used• Shadowline details optional

Note: Edge cover is defined as fully supporting the glass – glazing gasket or wedge extending beyond the frame backing should not be considered as part of the edge cover.

Internal cleated corners can also reduce the pocket depths and make it impossible for the glass to comply.

Detail 1. Shuffle Glazing Tolerances - 2 Or More Glass Panels

Detail 2. Shuffle Glazing Tolerances - 1 Glass Panel

HAS314-FM AS132 FINNED MULLION

2.8M C/A: 1817043.6M C/A: 1817412.8M BLK: 4526553.6M BLK: 452656

132

25

HAS311-SH AS132 SHADOW CAP

2.8M C/A: 4526483.6M C/A: 452650

132

A SERIES 132

A SERIES 132A SERIES 132

HAS310-R AS132 REBATED HEAD TRACK

2.8M C/A: 4526253.6M C/A: 4526282.8M BLK: 4526273.6M BLK: 452630

HAS310-SH AS132 SHADOWLINE HEAD TRACK

2.8M C/A: 1816473.6M C/A: 1817062.8M BLK: 4526423.6M BLK: 452644

HAS310-A AS132 HEAD TRACK

2.8M C/A: 4526333.6M C/A: 4526362.8M BLK: 4526353.6M BLK: 452638

HAS310 AS132 HEAD TRACK

2.8M C/A: 1816723.6M C/A: 1817242.8M BLK: 4526173.6M BLK: 452622

HAS009-150 150MM SKIRTING

2.8M C/A: 1032833.6M C/A: 1032992.8M BLK: 1602193.6M BLK: 160220

100 15

0

132132

132

35

132

25

HAS009-100100MM SKIRTING

2.8M C/A: 1032823.6M C/A: 1032982.8M BLK: 1087733.6M BLK: 160218

HAS312-MAP AS132 MULLION ADAPTOR

2.8M C/A: 1816443.6M C/A: 1817012.8M BLK: 4526523.6M BLK: 452654

HAS311-JP AS132 JOINTING PLATE

2.8M C/A: 1875753.6M C/A: 452646

HAS314-A AS132 DEEP POCKET MULLION

2.8M C/A: 4526573.6M C/A: 4526602.8M BLK: 4526593.6M BLK: 452662

132132

15126

HAS311-FF AS132 FLUSH FILLER

2.8M C/A: 1815883.6M C/A: 181606

132

HAS319-BA AS132 GLAZING BASE

2.8M C/A: 1816653.6M C/A: 1817202.8M BLK: 4526773.6M BLK: 452679

HAS318-45 AS132 CLIP IN 45MM

DOOR STOP

2.8M C/A: 4514723.6M C/A: 4514752.8M BLK: 4514743.6M BLK: 451477

HAS317-40 AS132 CLIP IN 40MM DOOR STOP

2.8M C/A: 1976983.6M C/A: 1977012.8M BLK: 1977003.6M BLK: 197703

HAS317-35 AS132 CLIP IN 35MM DOOR STOP

2.8M C/A: 1976923.6M C/A: 1976952.8M BLK: 1976943.6M BLK: 197697

HAS316-GAP AS132 GLAZING ADAPTOR

2.8M C/A: 1816213.6M C/A: 1816622.8M BLK: 4526733.6M BLK: 452675

HAS315-35FLM AS132 FINLESS MULLION

2.8M C/A: 4526673.6M C/A: 4526702.8M BLK: 4526693.6M BLK: 452672

25

132

132

35

HAS023 AS132 FILLER PLATE

2.8M C/A: 1550073.6M C/A: 1815102.8M BLK: 1815023.6M BLK: 181512

HAS322 AS132 GLAZING BEAD

2.8M C/A: 1815463.6M C/A: 1815612.8M BLK: 4526923.6M BLK: 452693

HAS321-B AS132 GLAZING TRANSOM

2.8M C/A: 4526863.6M C/A: 4526892.8M BLK: 4526883.6M BLK: 452691

HAS321-A AS132 GLAZING TRANSOM

2.8M C/A: 4533593.6M C/A: 4533722.8M BLK: 4533713.6M BLK: 453374

HAS320 AS132 GLAZING BEAD

2.8M C/A: 4526803.6M C/A: 4526832.8M BLK: 4526823.6M BLK: 452685

25

132

53

HAS324-FCP AS132 FLUSH CORNER POST

2.8M C/A: 4526983.6M C/A: 4527012.8M BLK: 4527003.6M BLK: 452703

HAS324-CP AS132 CORNER POST

2.8M C/A: 1817533.6M C/A: 4526952.8M BLK: 4526943.6M BLK: 452697

HAS313-A AS132 ADJUST MULTI TRACK

2.8M C/A: 4555273.6M C/A: 4555602.8M BLK: 4555293.6M BLK: 455562

HAS313-B AS132 ADJUST MULTI TRACK

2.8M C/A: 4555633.6M C/A: 4555662.8M BLK: 4555653.6M BLK: 455568

132132.5

C SERIES 45

C Series 45 is used as a commodity system when budget is a factor but can also be designed into the A Series for a slimmer look.

The system has the following options available:

• Standard glazing profile of 45mm wide x 25mm high• Standard wall size based around 64mm or 92mm steel stud with one layer of

plaster board each side• Can accommodate glass thicknesses between 6mm - 12.38mm max• Door thicknesses between 38mm - 50mm max can be used• Can be fixed to standard openings or fixed to 104 or 132 series head/sill track

GLASS VIEWING REQUIREMENTS

Glass quality is defined by AS/NZS 4667:2000 Quality Requirements for cut-to-size and processed glass, which sets out the allowable tolerances for thickness, size, squareness, flatness, bow, surface imperfections and internal imperfections. 1. Clean with proprietary glass cleaner2. Stand 3m from the glass and at 90 Degrees (Square On) to the glass (AS/NZS

4667:2000 states to stand a distance of > 2m)3. View in normal daylight conditions – there should be no visible imperfections4. If faults are evident, clean the surface again to see if they can be removed5. Re-examine and mark any remaining faults6. Glass quality also identifies items that may occur as a result of manufacture and may not

be considered a defect

Anodised Aluminium Viewing Visual inspection of anodising after manufacture should be done from a distance of not less than 2m in daylight, but not direct sunlight. It is sometimes possible to observe, on close inspection or from certain viewing angles, variations in brightness, banding, streaming and other visual effects on the significant surfaces. These seldom impair the performance of anodised aluminium and should not be grounds for rejecting the product on a performance basis. View Powder coated Aluminium Powder coating surface finishing – appearance in situ gives the following criteria when assessing finish quality. View powder-coated aluminium from a minimum distance of 2m away. Further distance may be allowed depending on the use of the product and its in situ viewing distances. A significant defect is one that is visible from 2m and has an outside diameter of more than 1.5mm. From 2m, the coating on the primary visible internal and external surfaces shall be of uniform appearance, colour, texture and be free from significant defects. However, the coating may contain one minor defect as defined for every 1m of extruded length. A minor defect may be visible from 2m and has an outside diameter of up to and including 1.5mm.

HAS004-P120 CS45 GLAZING POST

2.8M C/A: 4538383.6M C/A: 4539712.8M BLK: 4539703.6M BLK: 453973

104

259

C SERIES 45

C SERIES 45

HAS600-A35 SOHO75 GLAZING A-FRAME

3.6M C/A: 4546803.6M BLK: 454681

HAS601-F35 SOHO75 GLAZING FLAT BAR

3.6M C/A: 4546833.6M BLK: 454684

HAS011 AS104 FLUSH FILLER

2.8M C/A: 1550593.6M C/A: 1815912.8M BLK: 1602263.6M BLK: 181593

HAS010-R AS104 REBATED HEAD TRACK

2.8M C/A: 4532423.6M C/A: 4532472.8M BLK: 4532463.6M BLK: 453249

HAS006 CS45 GLAZING COVER

2.8M C/A: 1550543.6M C/A: 1815202.8M BLK: 1602123.6M BLK: 181522

HAS005 CS45 GLAZING BEAD

2.8M C/A: 1032503.6M C/A: 1678952.8M BLK: 1602113.6M BLK: 181529

HAS004-GP70CS45 GLAZING POST

2.8M C/A: 4502453.6M C/A: 4502482.8M BLK: 4502473.6M BLK: 450270

HAS004CS45 GLAZING BASE

2.8M C/A: 1032753.6M C/A: 1678942.8M BLK: 1601733.6M BLK: 181573

HAS001CS45 GLAZING FRAME

2.8M C/A: 1769043.6M C/A: 1815812.8M BLK: 1815633.6M BLK: 181583

HAS009-150CS45 150MM SKIRTING

2.8M C/A: 1032833.6M C/A: 1032992.8M BLK: 1602193.6M BLK: 160220

HAS009-100CS45 100MM SKIRTING

2.8M C/A: 1032823.6M C/A: 1032982.8M BLK: 1087733.6M BLK: 160218

HAS008CS45 DOORJAMB SUITS DOORS TO 40-45MM THICK

2.8M C/A: 1032723.6M C/A: 1816022.8M BLK: 1602153.6M BLK: 181604

HAS007CS45 DOORJAMB SUITS DOORS TO 35MM THICK

2.8M C/A: 1032713.6M C/A: 1678972.8M BLK: 1602133.6M BLK: 181586

HAS010-SH AS104 SHADOWLINE HEADTRACK

2.8M C/A: 1550643.6M C/A: 1816952.8M BLK: 1816973.6M BLK: 182829

45

120

HAS010-FH AS104 HEAD/SILL TRACK

2.8M C/A: 1032783.6M C/A: 1816802.8M BLK: 1602223.6M BLK: 181682

35

3510410

104

64

25

104

25

13

20

45

25

45

25

45

8

10054

23

45

23

45

70

150

D SERIES 45

Doors + Sliders has the following features:

• Designed to fit with Himmel Aluminium Systems• Available in 45mm thick doors only• Stiles and rail sizes 60mm, 66mm, 83mm and 114mm• Can accommodate glass thicknesses of 13mm laminated glass

GLASS OPTIONS

Glass Information For more information on all glass types consult with our partners Viridian Glass or the Australian Glazing Associations. Glass Thickness Typical to all Himmel Aluminium Systems, the glass thickness range the suites can accommodate is 6mm - 13mm maximum for laminated glass. For more information on glass thickness and compliance with the Australia Building Code requirements, refer tothe “Human Impact Safety Requirements”. Glass Weight Generally 2mm Glass thickness per m2 = 5kg, ie 6mm glass = 15kg/m2

Glass to Metal Contact Glass should be installed without glass-to-metal contact, as thermal movement created by the different coefficients of expansion between glass and metal can cause breakage, particularly in annealed and laminated glass.Himmel Aluminium Systems provide backing seals (ACE Captive Wedge) and glazing tapes. Where possible, these gaskets should be pre-installed. Although some systems can be double wedged, it is a more costly glazing procedure and not recommended by gasket/wedge suppliers nor glass companies.

8mm 20kg SQM

10mm 25kg SQM

12mm 30kg SQM

D SERIES 45

D SERIES 45

HAS554 DS45 130 TOP

ROLLER PELMET CAP

3M C/A: 4503563M BLK: 450357

HAS551 DS45 130 TOP ROLLER PELMET

5M C/A: 4503505M BLK: 450351

HAS510 DS45 BOTTOM ROLLER

TOP GUIDE FRAME

5M C/A: 4503295M BLK: 450330

HAS509 DS45 SLIDING DOOR

LOCATING FRAME

2.8M C/A: 4503233.6M C/A: 4503262.8M BLK: 4503243.6M BLK: 450327

HAS508-B DS45 BOTTOM ROLLER TRACK B

5M C/A: 1976895M BLK: 197690

HAS508-A DS45 BOTTOM

ROLLER TRACK A

5M MILL: 197688

HAS506 DS45 SLIDING DOOR PICK UP

3.0M C/A: 4568633.0M BLK: 456864

HAS535 DS45 114MM PLAIN STILE

2.8M C/A: 1781096.5M C/A: 1821622.8M BLK: 1821063.6M BLK: 182164

HAS507 DS45 T-ROLLER INTERNAL GUIDE

3M MILL: 453556

HAS552 DS45 130 TOP ROLLER MAIN FRAME

5M C/A: 4503535M BLK: 450354

HAS550 DS45 130 TOP ROLLER BASE FRAME

5M C/A: 4503475M BLK: 450348

HAS549 DS45 DOOR LOCATING FRAME

2.8M C/A: 4503413.6M C/A: 4503442.8M BLK: 4503423.6M BLK: 450345

HAS553 DS45 200T ROLLER TRACK

5M C/A: 453269

HAS525F DS45 130 TOP RAIL 68MM

3M C/A: 4532663M BLK: 453268

HAS512 DS45 BOTTOM ROLLER 1 PC

TOP GUIDE FRAME

5M C/A: 4503355M BLK: 450336

HAS511 DS45 BOTTOM ROLLER TOP

GUIDE CAP

5M C/A: 4503325M BLK: 450333

HAS534 DS45 114MM

FINGER PULL STILE

2.8M C/A: 1821012.8M BLK: 1821036.5M C/A: 1821586.5M BLK: 182160

HAS526 DS45 115MM BOTTOM RAIL

2.8M C/A: 1820823.6M C/A: 1821122.8M BLK: 1820843.6M BLK: 182114

HAS525 DS45 83MM TOP RAIL

2.8M C/A: 1820623.6M C/A: 1820862.8M BLK: 1820643.6M BLK: 182088

HAS528 DS45 DOOR RAIL BEAD

2.8M C/A: 1815063.6M C/A: 1815242.8M BLK: 1815073.6M BLK: 181526

HAS524 DS45 60MM HINGE STILE

2.8M C/A: 1820506.5M C/A: 1821242.8M BLK: 1820526.5M BLK: 182126

HAS523 DS45 66M SLIDE BACK STILE

2.8M C/A: 1820746.5M C/A: 1821402.8M BLK: 1820766.5M BLK: 182142

HAS522 DS45 60MM LOCK STILE

2.8M C/A: 1820586.5M C/A: 1821282.8M BLK: 1820606.5M BLK: 182130

HAS521 DS45 66MM PIVOT STILE

2.8M C/A: 1820782.8M BLK: 182080

HAS520 DS45 60MM PLAIN STILE

2.8M C/A: 4535603.6M C/A: 4535632.8M BLK: 4535623.6M BLK: 453565

HAS533 DS45 60MM MEETING STILE

3.25M C/A: 1882563.25M BLK: 188258

6M C/A: 1821366M BLK: 182138

HAS532 DS45 45MM MID-RAIL

6.5M C/A: 1821106.5M BLK: 182111

HAS531 DS45 114MM DOOR HINGE STILE

2.8M C/A: 1820906.5M C/A: 1821502.8M BLK: 1820916.5M BLK: 182152

HAS530 DS45 114MM LOCK STILE

2.8M C/A: 1820976.5M C/A: 1821542.8M BLK: 1820996.5M BLK: 182156

HAS529 DS45 114MM SLIDING STILE

2.8M C/A: 1781106.5M C/A: 1821662.8M BLK: 1821083.6M BLK: 182168

HAS527 DS45 124MM MID-RAIL

6.5M C/A: 1828696.5M C/A: 182871

104

42

5956 60

42

45

60

45

114

45

114

45

114

42

124

45

114

42

115

42

83

42

60

45

66

45

60

45

60

45

66

59 59 104

59

114

130

130

99

68

E SERIES 104

E Series 104 provides an edgeline glazing and twin glazing design with clean lines giving a clean look to your partition system. E Series 104 gives a standard detail of 104mm x 25mm, 104mm x 35mm, 104mm x 50mm.

E Series 104 has the following features:• Can accommodate glass thicknesses between 6mm and 13mm• Door thicknesses of 35mm - 45mm can be used• Standard wall size based around 64mm steel stud with one layer of 13mm

Gyprock plaster board on each side

Figure 33 Acoustic Twin Glazing Source Himmel Aluminium Systems

Figure 34 Acoustic Twin Glazing Source Himmel Aluminium Systems

Figure 35 Illustrates Sound As It Travels Through The Dissimilar Glasses

HIGH PERFORMANCE SOLUTIONS

A variety of high performance solutions can be tailored for different applications. For specific or high level noise, an acoustic engineer can provide a solution. They will assess the level and types of noise affecting the building and specifiy the appropriate solution. A common misunderstanding is that double glazing is effective at attenuating noise. Studies have shown that ordinary double glazing with a standard gap of about 12mm does not substantially improve acoustic performance, as the gap is too small to provide any real benefit. The most effective solution is to increase the gap to at least 100mm. This is most commonly referred to as secondary glazing, as it involves two separate window frames. Another solution is to use two pieces of glass (either in an IGU or Laminate) with each a different thickness. For instance, one pane might be 4mm and the other 6mm. Each pane in a dissimilar glass unit will block different sound frequencies.

The thicker pane targets lower frequency sounds like a neighbour’s stereo or traffic noise. The thinner pane targets higher frequency sounds like screaming and jet aircraft. This leads to a reduction in amplitude (loudness) across a wider spectrum of frequencies and the result is a much higher acoustic rating than for a window with standard glazing. The thicker glass should be about 40% thicker than the thinner glass to have the most benefit. Recent advances in the manufacture of the interlayer of laminated glass have provided an improvement in acoustic performance. Acoustic laminates have a thicker (0.52mm) specialised interlayer than is commonly used and provide some improvement over standard laminates. These interlayers are most effective when used with dissimilar glass thicknesses.

NOISE REDUCTION BY GLASS TYPETable 3 shows the indicative noise reduction for various options compared to 3mm glass.

FLOOR LEVEL

GLAZING PANEL

ACE CAPTIVEWEDGE

HAS310-AAS132 CAPPINGHEAD/FRAME

OWA CEILING LEVEL

GLAZING WEDGE

HAS339ES132 TWIN GLAZINGSNAP IN POCKET

HAS033ES104 EDGEGLAZING FRAME

HAS336ES132 TWIN GLAZINGBEAD

GLAZING PANEL

HAS005CS45 GLAZING BEAD

GLAZING PANEL

ACE CAPTIVEWEDGE

TM

I NTERIOR SYSTEMS

SCALE ISSUED DATESHEETWWW.HIMMEL.COM.AUSUBJECT TO CHANGE WITHOUT NOTICE

HIMMEL ALUMINIUM SYSTEMS

1 : 2 @ A4 11/07/198.2.3

E SERIES 132 - TWIN GLAZING WALL CROSS SECTION

FLOOR LEVEL

GLAZING PANEL

ACE CAPTIVEWEDGE

HAS010-AAS104 CAPPINGHEAD/FRAME OWA CEILING LEVEL

HAS033ES104 EDGEGLAZING FRAME

HAS039ES104 TWIN GLAZINGSNAP IN POCKET

GLAZING PANEL

HAS005CS45 GLAZING BEAD

GLAZING PANEL

HAS036ES104 TWIN GLAZINGBEAD

GLAZING PANEL

GLAZING WEDGE

GLAZING WEDGE

ACE CAPTIVEWEDGE

TM

I NTERIOR SYSTEMS

SCALE ISSUED DATESHEETWWW.HIMMEL.COM.AUSUBJECT TO CHANGE WITHOUT NOTICE

HIMMEL ALUMINIUM SYSTEMS

1 : 2 @ A4 15/07/196.2.3

E SERIES 104 - DOUBLE GLAZING WALL CROSS SECTION

Voice Noise Reduction % Traffic Noise Reduction %

6.38mm laminated glass 13 6.38mm laminated glass 24

10mm glass 24 10mm glass 38

10.38mm laminated glass 29 10.38mm laminated glass 43

4mm/12mm gap / 6mm 19 4mm/12mm gap / 6.38mm laminated glass 46

10mm/12mm gap / 6mm 34 6mm / 100mm gap / 4mm 57

6.38mm laminated / 8mm / 4mm gap 46

E SERIES 104

E SERIES 104

HAS044 ES104 EDGE GLAZING TRANSOM CAP

2.8M C/A: 4527853.6M C/A: 4527882.8M BLK: 4527863.6M BLK: 452789

HAS042 ES104 TWIN GLAZE TRANSOM CAP

2.8M C/A: 4527733.6M C/A: 4527762.8M BLK: 4527743.6M BLK: 452777

HAS041 ES104 TWIN GLAZING TRANSOM BAR

2.8M C/A: 4534383.6M C/A: 4534412.8M BLK: 4534393.6M BLK: 453442

HAS040 ES104 TWIN GLAZING FRAME

2.8M C/A: 4534323.6M C/A: 4534352.8M BLK: 4534333.6M BLK: 453436

HAS039 ES104 TWIN GLAZING SNAP IN POCKET

2.8M C/A: 4534263.6M C/A: 4534292.8M BLK: 4534273.6M BLK: 453430

HAS038 ES104 EDGE GLAZING SNAP IN POCKET

2.8M C/A: 4534203.6M C/A: 4534242.8M BLK: 4534213.6M BLK: 453424

HAS036 ES104 TWIN GLAZING BEAD

2.8M C/A: 4534143.6M C/A: 4534172.8M BLK: 4534153.6M BLK: 453418

HAS035 ES104 TWIN GLAZING MULLION FRAME

2.8M C/A: 4534083.6M C/A: 4534112.8M BLK: 4534093.6M BLK: 453412

HAS034 ES104 EDGE GLAZING BEAD

2.8M C/A: 4534023.6M C/A: 4534052.8M BLK: 4534033.6M BLK: 453406

HAS033 ES104 EDGE GLAZING FRAME

2.8M C/A: 4533963.6M C/A: 4533992.8M BLK: 4533973.6M BLK: 453400

HAS032 ES104 EDGE POCKET CAPPING

2.8M C/A: 4533903.6M C/A: 4533932.8M BLK: 4533913.6M BLK: 453394

HAS043 ES104 TWIN GLAZE TWO PCE MULLION

2.8M C/A: 4527793.6M C/A: 4527822.8M BLK: 4527803.6M BLK: 452783

104

104

104

25

2525

104

25

104

35

E SERIES 132

REGULATORY REQUIREMENTS

The NCC covers the internal acoustic considerations in Volume 1 for multiple dwellings Class 2, 3 and 9c buildings, but does not provide specific guidance for other building types. In some circumstances, such as near main roads and airports, additional requirements may be required. These are generally covered by Local Government authorities.AS/NZS 2107 contains recommendations for the internal sound levels that should be achieved for various rooms based on their intended use. While the standard is not called up in the NCC, it does provide guidance for building designers and planning authorities.

ACOUSTIC PERFORMANCE OF GLASS

Generally speaking, thicker glass performs better in attenuating noise. However, different glass thicknesses perform differently at different frequencies. At the lower frequencies, 12mm glass is much more effective than 4mm or 6mm while there is little difference at the higher frequencies. Where the noise problem is traffic and other low frequency noises, a thicker glass will provide the most benefit.The graph lines in Figure 31 rise and then suddenly dip. This happens when the glass vibrates in unison with the frequency of the sound. This is called the ‘coincidence dip’. Laminated glass performs slightly better than monolithic glass of the same thickness, especially at higher frequencies.The graph, Figure 32, compares 6mm laminated glass with 6mm float glass. Note the coincidence dip in the float glass at 2000Hz compared with a smaller dip for the laminated glass.

E Series 132 provides an edgeline glazing and twin-glazing design with clean lines to provide a clean look to your partition system. E Series 132 gives a standard detail of 132mm x 25mm, 132mm x 35mm or 132mm x 50mm.

E Series 132 has the following features:• Can accommodate glass thicknesses between 6mm and 13mm• Door thicknesses of 35mm – 45mm can be used• Standard wall size based around 92mm steel stud with one layer of 13mm

Gyprock plaster board on each side

E SERIES 132

E SERIES 132

HAS044 ES104 EDGE GLAZING TRANSOM CAP

2.8M C/A: 4527853.6M C/A: 4527882.8M BLK: 4527863.6M BLK: 452789

HAS343 ES132 TWIN GLAZE TWO PCE MULLION

2.8M C/A: 4527673.6M C/A: 4527702.8M BLK: 4527683.6M BLK: 452771

HAS042 ES104 TWIN GLAZE TRANSOM CAP

2.8M C/A: 4527733.6M C/A: 4527762.8M BLK: 4527743.6M BLK: 452777

HAS336 ES132 TWIN GLAZING BEAD

2.8M C/A: 4527373.6M C/A: 4527402.8M BLK: 4527383.6M BLK: 452741

HAS335 ES132 TWIN GLAZING MULLION FRAME

2.8M C/A: 4527313.6M C/A: 4527342.8M BLK: 4527323.6M BLK: 452735

HAS334 ES132 EDGE GLAZING BEAD

2.8M C/A: 4527253.6M C/A: 4527282.8M BLK: 4527263.6M BLK: 452729

HAS033 ES104 EDGE GLAZING FRAME

2.8M C/A: 4533963.6M C/A: 4533992.8M BLK: 4533973.6M BLK: 453406

HAS332 AS132 EDGE POCKET CAPPING

2.8M C/A: 4534443.6M C/A: 4534472.8M BLK: 4534453.6M BLK: 453448

HAS341 ES132 TWIN GLAZING TRANSOM BAR

2.8M C/A: 4527613.6M C/A: 4527642.8M BLK: 4527623.6M BLK: 452765

HAS340 ES132 TWIN GLAZING FRAME

2.8M C/A: 4527553.6M C/A: 4527582.8M BLK: 4527563.6M BLK: 452759

HAS339 ES132 TWIN GLAZING SNAP IN POCKET

2.8M C/A: 4527493.6M C/A: 4527522.8M BLK: 4527503.6M BLK: 452753

HAS338 ES132 EDGE GLAZING SNAP IN POCKET

2.8M C/A: 4527433.6M C/A: 4527462.8M BLK: 4527443.6M BLK: 452747

132

132

132

25 25 25

132

25

132

35

ACCESSORIES

HAS STAKE 1103322

HAS STAKE 10456994

HAS ACE CAPTIVE WEDGE457855

HAS JAMBSEAL INFILL/ MOHAIR170661187312

PASACC 009BLACK/GREY SKIRTING INFILL

103248103249

HAS GLAZING POST SPIGOT451912451911

HAS STAKE 3103321

HAS STAKE 6450932

HAS STAKE 7450933

HAS STAKE 8450934

HAS STAKE 9456993

www.himmel.com.au