• All Weather Durable PVC• Won’t Dent, Rust, Rot or Mildew• Tall Walk In Shed• Never Needs Painting• 61 Inch Wide Double Doors• Easy Assembly• High Wind Tested• Snow Load Tested 20lbs/sq. foot• Pad Lock Ready (Lock not included)• Wooden or Cement Foundation Needed

Call us for any missing or damaged parts.Do not return to the store.

CustomerService Hotline(800) 483-4674www.uspolymersinc.com

Requires two people and takes about4-5 hours for Installation.

Your Total Solution To Maintenance Free Storage Sheds.

Available Kits• Foundation Kit Available• Modular 2.5 Ft Extension Kits Available• 10 Ft x 8 Ft Window Kits Available

Ver: 0.0

Building Dimensions :Approximate

SizeStorage Exterior Dimension Interior Dimension

10 Ft x 8 Ft 79 Sq. Ft 480 Cu.Ft

Roof Edge to EdgeBase Dimension Door Opening

3.2 m x 2.4 m 7.3 Sq.m 13.6 Cu.m

WidthDepthHeight

inch cm125 3/8 318.4

inch cm

94 1/4 239.3125 1/2 318.795 1/8 241.6

91 231.2

inch cm123 3/8 313.3

inch cm

92 1/4 234.360 5/8 154

71 1/2 181.673 185.5

Wall to WallArea Volume

OWNER’S MANUAL / Instructions for Assembly ‘10 Ft WoodSide’Size 10 Ft x 8 Ft / 3.2 m x 2.4 m (Approx.)

Vinyl Garden ShedVinyl Garden ShedA Product of

TM

A L L P U R P O S E V I N Y L G A R D E N S H E D S

Duramax Garden ShedLimited Fifteen Year Warranty

U.S. Polymer Inc. will send a replacement part free of charge, in the event of material defects and or workmanship for a period of fifteen years from the date of purchase.

This warranty is extended only to the original purchaser. A purchase receipt or other proof of date of original purchase will be required before warranty service is rendered. In no event shall we pay the cost of flooring, labor, installation or any other costs related thereto.

This warranty only covers failures due to defects in material or workmanship which occurs during normal use and does not extend to color change arising due to normal weathering or to damage resulting from misuse or neglect, commercial use, failure to follow assembly instructions and the owner’s manual (including proper anchoring of the shed), painting, forces of nature and other causes which is beyond our control.

Claims under this warranty must be made within the warranty period by calling 1-800-483-4674 or mail in a dated sales slip and clear photograph of the part to:

U.S. Polymers, Inc.1057 S. Vail Ave, Montebello, CA 90640.

We reserve the right to discontinue or change components. If a component has been discontinued or is not available,U.S. Polymers, Inc. reserves the right to substitute a component of equal quality as may be compatible.

Limits and Exclusions

There are no express warranties except as listed above. The warrantor shall not be liable for incidental or consequential damages resulting from the use of this product, or arising out of any breach of this warranty. All express warranties are limited to the warranty period set forth above . Some states do not allow the exclusion or limitation on how long an implied warranty lasts, so the above limitations may not apply to you.

This warranty gives you specific legal rights and you may also have other rights which vary from state to state or country to country.

1

2

SAFETY & PRECAUTIONS

Before You Begin...

1. Check your local building codes regarding footings, location, etc.

2. Select a site that allows enough working space around the shed.

3. Determine building foundation and anchor system.

4. Read and understand the Owner’s manual enclosed in the package.

5. Follow all directions and dimensions thoroughly.

6. Follow the steps given in the manual carefully for correct assembly.

7. Make sure all parts are present before you start assembling.

8. BE SAFE : Follow safety instructions and avoid injury. (See inside page).

9. GROUND MUST BE EVEN : Make sure the foundation frame lies flat on the ground. If the earth bed is uneven, remove sod and other debris andlevel it with a flat shoval.

10. Separate contents of the carton by the part number and review the list. Be sure you have all the necessary parts for your shed.Refer Owner’s manual for part list.

CAUTIONSharp Edges

3

SAFETY & PRECAUTIONSFor your own safety, please read and follow these instructions during the shed assembly.

1. Always wear work gloves, long sleeves and eye protection during assembly of the shed. Some pieces of the shed contain sharp edges and can cause injury.

2. Be cautious with the tools used for the assembly of the shed. Familiarize yourself with the operation of all the power tools.

3. Children and pets should be kept away from the assembly site to avoid any distractions and accidents.

4. When using a step ladder, make sure it is on even ground and fully open with the safety latch in place. Never concentrate your full weight on the roof or any part of the shed.

5. Do not attempt to assemble the shed on a windy day. Shed panels can be whipped across by the wind making the worksite difficult and dangerous.

4

IMPORTANTWear eye protection when using any form of power tools. Do not use voltage power tools in a wet or dampenviornment to avoid electric shock.

Do not use any part of the shed as a means of personal support while attaching componets during assembly.

The shed must be constructed on a solid base foundation. A concrete pad or a large size concrete patiostone squares is recommended for suitable floor base. Make sure it is firm and level and will allow drainageaway from the site. The base foundation should be at least 4 inches (100mm) larger than the shed dimensions.Please refer to the front page of your owner’s manual for the exterior dimensions of the shed. Manufacturer is not responsible for the choice and construction of the foundation.

For a concrete pad base, prepare a level bed for a firm footing layer of crushed stone. The concrete padshould then be poured to a thickness of 4 inches (100mm) to 5 inches (125mm). Allow to dry thoroughly for at least 48 hours

Your shed must be firmly anchored to the concrete pad or large concrete patio stone squares, to help protectagainst damage in high winds.

Care & MaintenanceAlthough this unit does not require any maintenance, care should be taken to prolong the life of your shed.

ROOF : Keep roof clean of leaves and snow with long handled, soft bristled broom. Heavy amountsof snow on the roof can damage the shed making it unsafe. Do not step on the roof.

WALLS : Do not rest any object against the wall panels of the shed.

DOORS : Keep doors closed to prevent wind damage.

FASTENERS : Regularly check your shed for loose screws, bolts, nuts, etc. And retighten them as necessary.

MOISTURE : With changing temperatures, condensation will accumulate inside the shed. Good ventilation will help in regulating and avoid moisture.

TIP : A noncorrosive caulking is helpful to seal the shed.

DO NOT store swimming pool chemicals in your building. Combustibles and corrosive must be stored in air tight containers

Parts List

Cordless Drill - Philips HeadHammer or Rubber malletCarpenters Square8’ Step LadderAdjustable pliersLevel - 3ft.Tape MeasureCaulk GunWaterproof Clear SiliconHand Gloves

Tools You Will Need

2. Maximum no. of Extension can be build upto 10’x13’ (ie. Two Extension).

Note

3. Shed with more than two extensions require Roof Super Support.Recomended Qty of Roof Super Support

For 10’x8’ Vinyl Shed - 2Nos.For additional each Extension - 1No.

1. Before starting installation, please refer Safety & Precautions.

5

B1LA, B1RA, B21,B22, B3LA, B3RA

CB1A, CB2A, CB3XA, CB4A, MJ

RS1A1, RS3H,RS3LH, RS8A1, RS9A1

RS5A1, RS6A1,RS7A1

RS2A, RS10A1, RS4XA, RS11A1,RS12A1

DSH1 RS14A

CDLA CDRA

CCA CMA

FDCL FDCR

FCB

FMC

FCCRJ EPSCBC

PIN PPG & PWS S1, S2, S7

CODE QTY

B1LA 1B1RA 1B21 2B22 2 B3LA 1B3RA 1 CB1A 2CB2A 2CB3XA 4CB4A 2RS1A1 4RS2A 4RS3LH 2RS3H 2RS4XA 4RS5A1 4RS6A1 2RS7A1 2RS13A1 8

CODE QTY

FDCL 1FDCR 1FCC 4FMC 7 FCB 4RJ 4 EPS 4CBC 3L 1R 1VC 2VCP 4PPG 80PIN 80S1 254S2 12S3 32S7 16

CODE QTY

RS8A1 4RS9A1 4MJ 7RS10A1 2RS11A1 2RS12A1 2RS14A 12DSH1 1CMA 7CCA 4CDLA 1CDRA 1SP 12FPLA1 2 FPRA1 2RPA1 6RRS1 3DL 1DR 1

PARTS ACCESSORIES

S3

VC VCP

R

L

R

Exploded View

CB4A

CB1A

B1LA

B1RA

B21

B22

B22

B21

B3LA

B3RA

6

FPLA1

FPRA1

FPLA1

RS3LH

RS3HMJ

RS3LH

RS3H

MJDSH1

RS1A1

RS8A1

RS9A1

RS2A

RS4XA

RS2A

RS4XA

RS13A1

RS7A1

RS12A1

RS10A1RS11A1

RS2A

RS1A1

RS2A

RS5A1

RS13A1

CMA

CMA

CMA

CMA

CMA

CMA

CMA

CCA

CCA

CCA

CCA

CDLA

CDRA

CB3XA

CB2A

MJ

CB3XA

MJCB2A

CB3XA

MJ

CB3XA

CB1A

CB4A

RS1A1

RS9A1

DL

DR

RRS1

RRS1

RRS1

RPA1

RPA1

RPA1

RPA1

RPA1

RPA1

FPRA1

SP

SP

SP

SP

SP

SP

SP

SP

SP

SP

SP

SP

RS6A1

RS13A1

RS13A1RS6A1

RS5A1

A. Foundation

7

1. Use pressure treated wood studs 2 x 4 (Actual size 2” x 3 1/2”, 50mm x 88.9mm) to create a platform frame that has an outside dimension of 96” x 127” (2438.4mm x 3225.8mm).

DuraMax must be installed on a level wooden platform or a level concrete foundation.

2. Using exterior grade CDX 3/4” (19mm) plywood, cut and fit together the sheets to form solid foundation as shown. Foundation must be square and level.

The following are the list of lumber and sizesyou will need.

Wooden Platform (Not Included)

Pressure Treated - Wood Studs:2ea 2” x 3 1/2” x 127” (50mm x 88.9mm x 3225.8 mm)6ea 2” x 3 1/2” x 89” (50mm x 88.9mm x 2260.6 mm)

Exterior Grade (CDX) - 3/4” (19mm) plywood2ea 3/4” x 48” x 96” (19mm x 1219.2mm x 2438.4mm)1ea 3/4” x 31” x 96” (19mm x 787.4mm x 2438.4mm)

L-Brackets: 4ea

The shed must be constructed on a solid base foundation. A concrete pad or a large size concrete patio stone squares is recommended for suitable floor base. Make sure it is firm and level and will allow drainage away from the site. The base foundation should be at least 4 inches(100mm)larger than the shed dimensions. Please refer to the front page of your owner’s manual for the exterior dimensions of the shed. Manufacturer is not responsible for the choice and construction of the foundation

Concrete Platform

Note For a concrete pad base, prepare a level bed for a firm footing layer of crushed stone. The concrete pad should then be poured to a thickness of 4 inches (100mm) to 5 inches (125mm). Allow to dry thoroughly for at least 48 hours

If the shed is assembled with wooden foundation on soil, use the soil anchor kit.

Note31”787.4mm.

48”1219.2mm.

48”1219.2mm.

96”

2438.4mm.

Note : If you have DURAMAX Foundation, please follow instruction manual in that package. If not, follow below wooden platform instruction.

Lay 2 x 4(Actual size 2”x 3 1/2”, 50mm x 88.9mm)

Note

50m

m (2

”)

88.9mm (3 1/2”)

31”787.4mm.24”609.6mm. 24”609.6mm. 24”609.6mm. 24”609.6mm.

96”

2438.4mm.

127”3225.8mm.

L- BRACKET

8

Parts Needed:B. Base Frame

Code Qty

B1LA 1B1RA 1B3LA 1B3RA 1B21 2B22 2S1 32

Note

S1

B22B1RA

90O

Using a carpenter square, line up corners. Align base bars, mark the concrete at the holes in the base and drill concrete with 1/2” (dia. 12.5mm) concrete bit to accept anchor bolts to a 1 3/4” (44mm) depth. Replace base and secure with 1/4” x 1 1/2” (M6 x 40mm) anchor bolts (Qty - 32Nos. not provided).

Assembly on concrete foundation

Note Measure in all direction as shown in figure to make the base channel assembly in a perfect.

1

M6 Anchor Bolt

Base ‘U’ Channel

Concrete

1. It is important that these instructions are followed step by step. 2. All parts are clearly marked and care should be taken to use the correct one.3. Don’t install under windy conditions.4. If you are building the shed against a wall, build it 2.5 ft. away then slide it in.

S1

123 3/8” 3133mm.

123 3/8” 3133mm.

92 1/4”

2343mm.

92 1/4”

2343mm.

61 1/4” 1556mm.

B1RAB22

B21

B3RA

B3LAB22

B21

B1LA

9

C. Wall & Columns

1

Front

Fig.3

Fig.1

CDRA

Fig.2

CDRA

B1RARight

Back Left

1

2&3

B1RA

CDRA

B1LA

B1RA

CDRA

S1

Parts Needed:Code Qty

CMA 7CCA 4CDLA 1CDRA 1CB1A 2CB2A 2CB3XA 4MJ 3CB4A 2FCB 4CBC 3SP 12S1 63S2 4

All parts are clearly marked and care should be taken to use the correct one.

Note

10

Check the stamped label on top of all panels inside.Note

SP

2

B1RA

CDRA

Fig.1

SP

Fig.2

CCA

B1RAB22

Fig.1

CCA

SP

Fig.3

CCA

S1

SP

S2

CCA

FCB

4

1

Fig.1

Do not tighten the screw. Leave it looseNote

Front

SP

CDRA

1

CCASP

1

2&3

B1RAB22

3

CCA

Fig.3

CB4A

CB1A

EPS

11

S1

CB1A

CDRA

Fig.2

5

6

2CB1A

CDRA

1

Fig.1

CB1A

S1

FCB

CB4A

B1RA

CDRA

1

2&3

CB4A

B1RA

Fig.1

S1

CB4ACDRA

Fig.2

S1

CB3XA

CB3XACB2A

S1

MJ

7

S1

CB2A

CB3XA

CB3XA

CB2A

S1

S1

CB3XA

CB3XA

MJ

MJ

MJ

12

Right Wall

S1

SPCMASP

CMA

B22

B21

8

Fig.3

Fig.1

CB3XA

FCBS1

CB3XA

S1

CMA

1&2

3

9

CB3XA CB1A

S1Fig.2

CMA

SP

CMA

B21Fig.3

CMACB3XA

S1

CB2A

Fig.4

CBCCB2A

CB3XACMA

SPCMA

S1

2

3&4

10

Fig.1 Fig.2

1

1

2Fig.1 Fig.2

CB3XA

CB2A

CMA

SPCCA

13

Right Wall

SP

CCA

B212&3

B3RA

SP

CCA

Fig.1

B3RA

B21

CCA

Fig.2

Fig.3

B3RA

CCA

S1

1

CCA

Fig.1

FCB

CCA

S2

Do not tighten the screw. Leave it loose.Note

CB2A

S1

FCB

CCA

Fig.1

1

1

11

12

13

CB2A

14

Back Wall

SP

CMASPCMA

B3RA

B3RA

2Fig.2

Back Wall

CMA

3

1&2

Fig.1 Fig.2

CB3XA

FCBS1

CB3XACB3A

S1

CB3XA

S1

CMA

Fig.3

Fig.3 Fig.4

SPCMA

S1

Fig.2

2

3&4CMA

CB3XA

S1

CB3XA

CBC

CB3XACMA

CB3XA B3RA

14

15

16

SP

CMA

Fig.1

1

S1

1

Fig.1

CB3XA

CB3XA

CB3XA

SPCCA

CMA

B22

B3LA

CCA

Fig.2 Fig.3S1

B22

CCA

SP

CCA

15

Back Wall

SP

CMA

2

SPCMA

S1

Fig.2

CB3XA

S1

CMA

Fig.3 B3LA

3

Fig.1

CCA SP

B3LA

1

2&3

CCA

FCB

CCA

S2

Do not tighten the screw. Leave it loose.Note

1

17

18

19

1

Fig.1

CB3XA

CMA

16

Back Wall

CB3XA

S1

FCB

CCA

Fig.11

CB3XA

Left Wall

SPCMA

S1

Fig.2

SP

CMA

CMA

Fig.1

CB2A

FCBS1

CB2A CB3XA

S1 Fig.2

Fig.3 Fig.4

CMACB2A

S1

CB3XA

CBC

CB2ACMA

CB3XA

3&4

1&2

Left Wall

B22

B21

20

21

22

Fig.1

1

2

CB3XA

CB2A

SPCCA

17

Do not tighten the screw. Leave it looseNote

Left Wall

S1

SPCMA

Fig.2

CB3XA

S1

CMA

Fig.3

CMA SP

3

2

SP

CCA

B22

B21

B1LA

B21

CCA

Fig.2 Fig.3S1

B1LA

CCA

SP

CCA

Fig.1

B1LA

Left Wall

2&3

1

FCB

CCA

S2

Fig.1

1

23

24

25

Fig.1

1

CMA

CB3XA

18

CCA

CB3XA

S1

FCB

Fig.1

CDLA

SP

Fig.1 Fig.2

CDLA

CDLA

B1LA

S1

SP

B1LA

Fig.1

CB1A

FCBS1

Fig.3

Fig.2

After completing the center band assembly, fully tighten the four center band fittings (FCB) to the corner column (CCA).

Note

1

1

2

CDLA

CB1A

1&3

2

CB1A

CDLA

S1

CB1A CB3XA

S1

CCA

26

27

28

Front

CB3XA

CDLA

CB4A

B1LA S1 CDLACB4A

S1Fig.1 Fig.2

Fig.3

CB4A

CB1A

EPS

CB4A

B1LA

2&3

1

61 1/4” 1556mm.

19

29

30

CDLA

CDRA

D. Roof Structures

Parts Needed:Code Qty

RS1A1 4RS2A 4RS3LH 2RS3H 2RS4XA 4RS5A1 4RS6A1 2RS7A1 2RS8A1 4RS9A1 4RS13A1 8MJ 4

CMA

FMC

20

1

CMA

CMACMA

CMACMA

CMA

CMA

S1

CMA

FMC

Code Qty

RS10A1 2RS11A1 2RS12A1 2DSH1 1FDCL 1FDCR 1FCC 4FMC 7RJ 4S1 159S2 4S3 32S7 16

FCC

CCA

FCC

CCA

S1

Fig.1

1

Fig.2

CDLA

FDCL

S1

CDRA

FDCR

S1

CDRA

CDLA

2

21

2

3

CCA

CCA

CCA

CCA

Roof Structures Assembly

22

RS1A1

RS2A

RS9A1

RS8A1

RS8A1

RS9A1RS10A1

DSH1

RS2A

RS4XA

RS4XA

RS4XA

RS4XA

RS11A1

RS11A1

RS12A1

RS12A1

RS2A

RS2ARS10A1

RS3LH

RS3H

RS3LH

RS3H

RS5A1

RS5A1

RS5A1

MJ

MJ

RS8A1

RS9A1

RS6A1

RS6A1

RS9A1MJ

MJ

RS1A1

RS1A1

RS1A1

RS13A1

RS13A1

RS13A1

RS13A1

RS13A1

RS13A1

RS13A1

RS13A1

RS7A1 RS7A1

23

Front roof structure assembly

RS1A1

RS1A1

RS2A

S1

RS9A1

RS9A1

RS2ARS8A1

RS8A1

RS2A

RS2A

S1RS1A1

RS1A1

MJ

5

4

6

S1

RS9A1

RS8A1

RS9A1

RS1A1

RS1A1

Make sure these holes upRS8A1

24

Back roof structure assembly

RS1A1

RS1A1

S1RS1A1

RS1A1

MJ

Make sure these holes up

RS2A

RS2A

S1

RS8A1

RS8A1RS9A1

RS9A1

RS2A

7

8

9

RS8A1

RS8A1

RS9A1

RS9A1

RS1A1

S1

RS1A1

RS3LH

RS3HS1

MJ

S1

S1

RJ S1

25

10

11

RJ

RS3LH

RS3H

RJ

S1

RJ

S1

RS3LH

RJ

RS3LH

RS3HS1

RS3LH

RS3HS1

RS3LHRJ

RS3LH

RS3H

RJ

RJ

S1

RS3LH

RS5A1

S1

26

RS6A1

S3

S1

RS5A1

RS7A1

12

13

14

Make Two SetsNote

Make Two SetsNote

Make Two SetsNote

RS5A1

RS6A1

RS13A1

RS13A1

S3

1&2Fig.1 Fig.2

Fig.3 Fig.4

RS1A1

CDRA

RS1A1

S1FDCR

RS2A

RS1A1

RS1A1

CDLA

3&4

CDRA

CDLA

S1FDCL

RS1A1

Front

27

15

16

Make Two SetsNote

RS5A1

RS7A1

RS13A1

RS13A1

RS1A1

DSH1

S1

DSH1

RS1A1

S1

RS1A1

1&2

3

DSH1

Back

CMA

RS1A1

CMA

CMA

Fig.1 Fig.2

Fig.3

28

17

18

Front

DSH1

S1

CMA

RS1A1

FMC

S1

1,2,3&4

RS1A1

RJ

S1 RJ

RS1A1

RJFCC

S2

RS2A

S1

RS3LH

Fig.1 Fig.2

Fig.3 Fig.4

RS3LH

RS3H

RS3LH

RS3H

RS3LH

S1FMC

29

19

20

Fig.1

Fig.2

Fig.1

Fig.2

30

21

22

RS5A1

RS6A1

RS5A1

RS7A1

1

2

RS6A1

RS5A1

RS5A1

RS7A1

1

2

RS8A1

S1

RS8A1

RS6A1

RS7A1

RS8A1RS8A1

RS5A1RS5A1

S1

S1RS9A1

RS5A1

S1

RS9A1

RS6A1

S1

RS4XA

RS3LH

Fig.1 Fig.2

Fig.3

Fig.1 Fig.2

Fig.3

Note Make sure the hole in (RS10A1) facing outward on both sides.

31

24

23

1

2

3

1

2

RS4XA

RS4XA

RS4XA

RS4XA

2

13

3

RS10A1

RS11A1

RS11A1

RS10A1

S1

RS10A1

RS5A1

S1

RS10A1

RS6A1

RS7A1

RS5A1

RS5A1

S1

RS11A1

RS4XA

RS5A1

S7

RS4XA

RS4XA

RS5A1

S7

RS5A1

32

25

RS12A1

RS5A1 RS7A1

RS5A1

RS6A1

RS12A1

RS5A1RS12A1

S1

D. Roof Panels

Parts Needed:Code Qty

RPA1 6FPLA1 2FPRA1 2RRS1 3PPG 80PIN 80RS14A 12

33

Insert roof plugs into Facia Panelonly as indicated.

FPRA1

1

Front

PPGPIN

Front

2

FPLA1

PPGPIN

FPRA1

Back

3

PPGPIN

4

Back

FPLA1

PPGPIN

FPRA1

PPG PIN

Note Use the same colour Plugs & Pins (PPG & PIN) to fix the Roof Panels & Facia Panels .

Note

1. Use a screw driver to align the holes.Note 2. Insert roof plugs into roof panels only as indicated.

Apply silicone around the roof plugs. This is optional and should be done for heavy rain areas if needed.

PPG

Back

34

10

Silicone

6

PPG

RRS1

7 Roof Panel installation by using ladder from inside at missing Panels.

Note

RPA1

Note

PPGPIN

8

RPA1

PPGPIN

PIN

5PPGPIN

RPA1

Front

9Back

RPA1

PPGPIN

35

11

RPA1 PPGPIN

Front

13

RPA1

PPGPIN

RRS1

PPG

12PIN

14

PPG

RRS1

PIN

Outside View Inside View

15

RS14A

RS14A

RS14A

RS14A

RS5A1

E. Door

36

1

2

Fig.1 Fig.2

Parts Needed:Code Qty

DL 1DR 1L 1R 1S2 4

1

2

DL

DR

Fig.1

Fig.2

S2

R

DR

S2

DL

L

R

R

L

Apply silicone around the perimeter of the base ‘U’ channel. Seal the corners, joints and base of door column. This is optional and should be done for heavy rain areas if needed.

Note

Base ‘U’channel

Silicone

Column

1

2

Fig.1

Silicone

Base ‘U’channel

Fig.2

37

F. Ventilation Kit

Parts Needed:Code Qty

VC 2VCP 4

Ventilation kits can be installed on any of the wall panels or Facia panels.

TOOLS YOU WILL NEED

Power DrillDia 5/32” (4.2mm) drill bitDia 1/2” (12.5mm) drill bit

VC VCP

4.2mm.(5/32”)

12.5mm.(1/2”)

Outside

Note

VC

SP

VC

VCP

SP

SP SP

38

1 2 3

4

Follow the same steps 1- 4for installing ventilation kit on Facia panels.

Note

5

VCVCP

Note: To ensure that your shed withstands high winds,you will need the following reinforcement.

High wind area installation instructions

Parts needed (not included) :

CODE DESCRIPTION QTY

S4 Dia. 4.2 x 16mm. (5/32” x 5/8”)Sheet Metal Screw 48

S5 M6 x 40mm. (1/4” x 1 1/2”)Anchor Bolt 32

Shed or shed foundation should be placed on concrete footing by use of anchor bolt. Using a carpenter square, line up corners. Align base bars, mark the concrete at the holes in the base and drill concrete with 1/2” (dia. 12.5mm) concrete bit to accept anchor bolts to a 1 3/4” (44mm) depth. Replace base and secure with 1/4” x 1 1/2” (M6 x 40mm) anchor bolts.

M6 Anchor Bolt

Base ‘U’ Channel

Concrete

Attach each side panel (SP ) on the bottom to the Base U-channel. Using a dia. 3mm (1/8”) drillwith a power drill, make two equal distance holeson the Base U-channel through the Side Panel.Drive a self tapping screw (S4) through the BaseU-channel to the Side Panel. Repeat this for every Side Panel. See blowup.

S4

SP

Base U-channel

SP

39

1

2

3.0mm.(1/8”)

Attach each Side Panel (SP ) on top to the Roof Structure (RS1A1, RS3LH & RS3H). Using a dia. 3mm (1/8”) drill with a power drill, make two equal distance holes on the Side Panel through the Roof Structure. Drive a self tapping screw (S4) through the Side Panel to the Roof Structure. Repeat this for every Side Panel. See blowup.

RS3H

RS1A1

S4

SP

RS1A1

Side Panel

Roof Structures

S4

Base U-channel

S4

The ‘DURAMAX’ shed has been tested and passed wind loads of up to 115 mph in a controlled laboratory environment. Natural high wind areas create wind at unpredictable speeds that are very difficult to capture accurately by location. As such we cannot guarantee the performance of the shed in these extreme situations.

Important Warranty Information

“We recommend to clear snow from the Roof top after each Snowfall.”40

3

3.0mm.(1/8”)

SP

RS1A1

41

ADDITIONAL ACCESSORIES AVAILABLEThese accessories are required in case of heavy snow or high wind areas. Please choose relevant accessories according to your needs.

SUPER SUPPORT KIT

Extra roof beams for added protection against heavy snow accumulation.For heavy snow area.

ANCHOR KIT (Soil)

Wire rope with twist augers for sheds installed with foundation (Wood / Metal) on soil.For heavy wind area.

ANCHOR KIT (Concrete)Eye bolt with wire rope for sheds installed with foundation (Wood / Metal) on concrete.For heavy wind area.

ANCHOR KIT (Foundation)Strap clamping for shed assembly with foundation(Wood / Metal) on concrete.To prevent shed from displacement.

SHELF KITEasy mounting system on the middle column. 6 inch wide reinforced PVC shelf with end caps.

SKY LIGHT KITTo illuminate your shed with natural light.

U.S. Polymers, Inc.1057 S. Vail Ave Montebello, CA 90640,United States of America English