Stuc

co &

Pla

ster

All products conform to ASTM D1784 cell classification 13244C Stucco & Plaster Accessories

For More Information Call Toll Free 1-800-648-4695 or Visit www.vinylcorp.com 1-29

1538R-200V 3/8"

5" overall width,

perforatedflange

2" 20

1550R-200V 1/2" 2" 18

1558R-200V 5/8" 2" 18

1575R-200V 3/4" 2" 15

1578R-200V 7/8" 2" 12

15100R-200V 1" 2" 122" Soffit Vent – Continuous one piece combination design like a controljoint allowing movement of the plast with a 2" vent area. Vent clips areprovided to connect soffit vent. Vent are 8 sq. inches per lineal foot.

Caulk all intersections, butt joints, ends and corners at time of installation.

2'' Soffit Vent Control Joint Combination

NEW

PRODUCTNUMBER GROUND DIMENSIONS

VENTEDREVEAL

PIECESPER BOX

1538R-300V 3/8"

6" overall width,

perforatedflange

3" 15

1550R-300V 1/2" 3" 15

1558R-300V 5/8" 3" 12

1575R-300V 3/4" 3" 12

1578R-300V 7/8" 3" 10

15100R-300V 1" 3" 103" Soffit Vent – Continuous one piece combination design like a controljoint allowing movement of the plast with a 3" vent area. Vent clips areprovided to connect soffit vent. Vent are 15 sq. inches per lineal foot.

Caulk all intersections, butt joints, ends and corners at time of installation.

3'' Soffit Vent Control Joint Combination

NEW

PRODUCTNUMBER GROUND DIMENSIONS

VENTEDREVEAL

PIECESPER BOX

1538R-400V 3/8"

7" overall width,

perforatedflange

4" 12

1550R-400V 1/2" 4" 12

1558R-400V 5/8" 4" 10

1575R-400V 3/4" 4" 8

1578R-400V 7/8" 4" 8

15100R-400V 1" 4" 84" Soffit Vent – Continuous one piece combination design like a controljoint allowing movement of the plast with a 4" vent area. Vent clips areprovided to connect soffit vent. Vent are 16 sq. inches per lineal foot.

Caulk all intersections, butt joints, ends and corners at time of installation.

4'' Soffit Vent Control Joint Combination

NEW

PRODUCTNUMBER GROUND DIMENSIONS

VENTEDREVEAL

PIECESPER BOX

VinylCorp_Sec01_28-29:VinylCorp_2011 7/1/11 11:40 AM Page 1-29

JDF08/27/15

X

DIV 9 - Stucco - product data - #09220 - par. 1.3

PRODUCT DATA SHEET

Rinker® stucco cement PRODUCT DESCRIPTION CEMEX Rinker® stucco cement meets the requirements of ASTM C91 for masonry cement and ASTM C1328 plastic (stucco) cement for use in stucco mixtures. Basic Use Rinker stucco cement will produce a stucco designated “MS” or “FMS” as defined in ASTM C926 “Standard Specification for Application of Portland Cement-Based Plaster.” This product, when proportioned and mixed in accordance with ASTM C926, is designed to provide excellent workability and bond.

Limitations Rinker stucco cement contains a water-repellent agent which is interground with the cement during finish grinding. No other additives are necessary.

When stucco is to be applied to smooth, non-porous solid substrates, a quality bonding agent (or other approved method outlined in ASTM C926) is recommended to be used to ensure adequate adhesion.

Mixing Approximately two thirds of the water should be added to the mixer with one half of the sand followed by the Rinker stucco cement. Add the remaining sand and sufficient water to reach the desired consistency and mix for no less than five full minutes. A mixing time from five to ten minutes can increase the air content and yield. The plaster mortar may be hand or machine applied. The number of coats and the thickness of the stucco should be consistent with industry standards.

Proportioning The stucco should be produced with sand meeting the requirements of ASTM C897 or ASTM C926. The stucco cement shall be proportioned in accordance with Tables 2 and 3 of ASTM C926.

Table 1 presents the approximate amount of stucco cement and sand batched at a 1:3 ratio, respectively, to produce stucco to cover 100 square feet of surface area based on the application thickness.

*Estimation based on 1 cubic foot of damp loose sand containing 80 lbs. of dry sand. (No allowance for waste.)

Curing A light fogging with water two times a day for three days will preserve the appearance of the wall while minimizing drying shrinkage, cracking and its associated de-bonding. It is recommended that users adhere to the curing procedures provided in ASTM C926.

TECHNICAL DATA Applicable Standards The following standards apply to the use of CEMEX Rinker stucco cement: ASTM C91, Standard Specification for Masonry Cements ASTM 1328, Standard Specification for Plastic (Stucco) Cement ASTM C926, Standard Specification for Application of Portland Cement-Based Plaster ASTM C897, Standard Specification for Aggregate for Job-Mixed Portland Cement-Based Plasters Water All water should be clean and free from organic material and deleterious amounts of dissolved acids, alkalies and salts. Precautions Freshly mixed cement, mortar, grout or concrete may cause minor skin irritations. Avoid direct contact with skin and eyes and if contacted, wash exposed areas promptly with water. Refer to the applicable CEMEX product MSDS prior to use which may be obtained by calling 1-800-99-CEMEX (1-800-992-3639).

Availability

CEMEX Rinker stucco cement is available in both bulk and/or 79 pound moisture resistant bags in some market areas, and can be ordered by contacting CEMEX Sales at 1-800-99-CEMEX (1-800-992-3639).

Table 1: Materials required to produce 100 square feet of surface area using a 1:3 mixture *

Thickness (inches) Rinker stucco cement bags

Volume of sand

(cubic feet) 1/2 2.0 6.0 5/8 2.5 7.5 3/4 3.0 9.0 1 3.5 10.5

Warranty CEMEX warrants that the products identified are in accordance with the appropriate current ASTM and Federal Specifications. No one is authorized to make any modifications or addition to this warranty. CEMEX makes no warranty or representation, either expressed or implied with respect to this product and disclaims any implied warranty of merchantability or fitness for a particular purpose.

As CEMEX has no control over the other ingredients mixed with this product or the final application, CEMEX does not and cannot warrant the finished work.

In no event shall CEMEX be liable for direct, indirect, special, incidental or consequential damages arising out of the use of this product, even if advised of the possibility of such damages. In no case shall CEMEX’s liability exceed the purchase price of this product.

TECHNICAL SERVICES CEMEX personnel are available to provide technical assistance by contacting 1-800-99-CEMEX (1-800-992-3639) CEMEX, Inc. U.S. OPERATIONS HEADQUARTERS 929 Gessner Rd., Suite 1900 HOUSTON, TEXAS 77024 (713) 650-6200, (800) 999-8529 www.cemexusa.com

amico-lath.com ALABAMA METAL INDUSTRIES CORPORATION 800/366-2642

3/8” Rib Lath (High Rib)

4

Refer to ASTM C1063 for support spacing, lath selection, fastener selection and further information regarding the proper installation of metal lath.ASTM and most codes require hot dipped galvanized lath for all exterior applications.AMICO recommends the use of zinc or vinyl beads for all exterior applications.

Application of “Brown” Coat over“Scratch” Coat

3/8” Rib Lath and scratch coat withbrown coat

Rib Lath provides an excellent plaster base for ceilingapplications

3/8” High Rib Lathis intended for horizontal applications with its seven longitudinal ribs,each 3/8 inch deep and eight small flat ribs to provide additional rigidity.The herringbone mesh pattern provides excellent bonding of the stuccoto the lath for ceiling and soffit installations. The 1/8” flat ribs at the outeredge of the sheet allows for a smooth overlap reducing plaster cracks atthe laps. For these reasons plus the fact that this product will span up to24” o.c. makes High Rib an excellent lath for horizontal installations.

High Rib LathWeights per Square Yard

Type Finish Sheet SizePieces

per BundleSquare Yardsper Bundle

3.4 lbs. Galvanized 27" x 96" 10 20

4.0 lbs. Galvanized 27" x 96" 10 20

50 Bundles per pallet equals 1000 square yards

BONDING AGENTCB–900 • CB-901

PROFESSIONAL GRADE CONCRETE BONDER 31% Solids

(Meets ASTM C-631 & C-932)

PRODUCT DESCRIPTION: A high solids concrete adhesive and fortifier for interior or exterior use, to

bond new concrete to old without the laborious scarification process whichis usually necessary. Stronger than most concrete, this powerful bondingagent will retain plasticity and never become brittle. It withstands humidityand temperatures from –40ºF to 300ºF (-40˚C to 149˚C); can be applied overdamp or dry surfaces and is not affected by alkalinity of lime plaster orPortland cement. Available in white or blue.

BASIC USES: To provide a permanent bond between structurally sound substrates such aswood, concrete, wallboard, acoustical tile and lime plaster.

PRODUCT ADVANTAGES: * Water resistant * 31% solids

* Excellent coverage * Safe to use* Water cleanup * Excellent bond strength* Non-flammable * Does not contain harmful solvents* Fast-drying

TECHNICAL DATA

Percent Solids: 31.00 ± 1% by weight Color: White (CB-900)28.00 ± 1% by volume Blue (CB-901)

Weight / Gallon: 8.78 ± 0.5 lbs. Viscosity: 2,600 – 2,700 cps.

Flash Point: Non-flammable Thinning: Water

Specific Gravity: 1.05 Coverage: 320 sq. ft./gal

Type of Emulsion: Vinyl acetate homopolymer pH: 8.5 ± 0.5

Drying Time: 20 minutes Sizes: 55 gallons5 gallons

Application Instruction: Satisfactory bonding can be obtainedby using the following procedure:(1) Stir contents of container thoroughly before use.

Do not dilute to make volume. (2) Surface should be free of dust, sand or foreign matter. (3) Apply a uniform coat of LANCO® Bonding Agent to the

surface by brush, roller or spray gun. (4) Before applying the concrete plaster check surface for

uniformity of color. Areas that are irregular in shade indicate an insufficient amount of LANCO® Bonding Agenthas been applied.

(5) Allow at least two hours for LANCO® Bonding Agent to cure before applying concrete plaster.

(6) If cured 24 hours, apply an additional coat of LANCO®

Bonding Agent before applying concrete plaster. (7) Always maintain the proper level of water in the concrete

plaster mix. Do not apply if too dry. (8) When troweling the concrete plaster use a circular motion

follow through on all strokes. Never pull the trowel away perpendicular to the surface.

Mixing: Always mix thoroughly by hand or with a power agitator before application.

Cleanup: Clean all equipment immediately after use with warmsoapy water. Completely flush all spray equipment with this solu-tion.

Caution: Do not take internally. Close container after each use.Keep out of reach of children. Use only with adequate ventila-tion.

Notice: The technical data contained herein are true and accurateto the best of our knowledge. Published technical data andinstructions are subject to change without prior notice.

M.S.D.S.: Available upon request.

Submittal Form

PAPER BACKED SELF FURRING DIAMOND MESH LATH

1.75, 2.5, 3.4

www.PHILLIPSmfg.com Version 1.1 800.822.5055

©2007 Phillips Manufacturing Company

Product Benefits

Dimples raise lath for superior mechanical bond over solid surfaces

Easily shaped for curved or contoured surfaces Maintains consistent plaster depths V-Groove eliminates the need for added furring

strips Paper backing speeds application

Dimpled lath is manufactured with approximately 103, ¼” deep dimples per sheet. The uniformly staggered indentations are designed to hold the lath sheet away from the solid surface it is fastened to. This will allow the plaster or stucco to penetrate the lath and form a strong mechanical bond with the lath. This product is used over solid surfaces such as concrete, cement board, column fire proofing, and over old surfaces for a face lift. For the furring to be affective the fasteners must be applied in the dimples. V-Groove lath is manufactured with approximately ¼” deep grooves, five per sheet. This product is used over concrete, cement board, column fire proofing, and masonry and over old surfaces. To maintain the furring characteristics, fasteners must be applied in the v-groove cavity.

Available in: Available in 1.75, 2.5, and 3.4 pounds per square yard. Certification Phillips Paper Backed Self Furring Diamond Mesh Lath meets or exceeds the following: ASTM C847-88, A366, A525-87, C841-87, Federal Specification QQ-L-101C, Federal Specification UU-B-790a, Type 1, Grade “D”, Style 2 Barrier Paper. Storage Avoid bending or other damage and store in a dry protected area. Installation Recommendations Phillips recommends installation in accordance with applicable ASTM standards and prevalent industry standards. Reference materials include ASTM C841, and ASTM C1063. Made in the U.S.A. Phillips is proud that all of our products are made right here in the U.S.A.. Standard Weight Sheet Size Pieces / Bundle Bundles / Skid Yards per Skid

1.75 27” x 96” 10 25 500 2.5 27” x 96” 10 25 500 3.4 27” x 96” 10 25 500

Submittal Approvals:

Submittal Form

PAPER BACKED SELF FURRING DIAMOND MESH LATH

1.75, 2.5, 3.4

www.PHILLIPSmfg.com Version 1.1 800.822.5055

©2007 Phillips Manufacturing Company

Job Name: _________________________________________________________________ Contractor: __________________________________________ Date: _________________

The information and recommendations contained herein are, to the best of Phillips Manufacturing Company’s knowledge and belief , accurate and reliable as of the date issued. Phillips Manufacturing Company has no control over the conditions of handling and use, and makes no warranty regarding the results obtained from the use of this data. The information and recommendations are offered for the user’s consideration and examination, and it is the user’s responsibility to determine that they are suitable and complete for its particular use. Phillips reserves the right to make alterations and amendments to the detailed specifications at its discretion. Phillips disclaims responsibility for all actions, proceedings, liabilities, claims, damages, cost, losses, and expenses in relation to, or arising out of, incorrect utilization of this information.

DESCRIPTION:n Basecoat for Parex EIFSn Adhesive to laminate EPS to

listed substratesn Applied without the addition of

cementn Mixed on site with watern Excellent workability USES:n EPS adhesive for the following

substrates: - Exterior grade gypsum sheathing - Glass mat gypsum sheathing - Masonry, concrete and cement board - EPS - Parex USA WeatherSeal Spray &

Roll-On and WeatherSeal Trowel-On Water Resistive Barrier Coatings

n Basecoat for Parex Nu-Tech Stucco and other architectural coatings and finishes (ACF).

n Leveler and filler for masonry, concrete, stucco surfaces. For this application only, 121 Dry Bascoat & Adhesive can be built up to 1/4 in. (6 mm) thick in a single pass.

COMPOSITION:n Binder base: Copolymer compatible

with portland cementn Water base: VOC-Compliantn Color: Light gray

WORKING TIME: Pot life is 1–2 hours after water has been added. Open time is affected by humidity and temperature.

DRYING TIME: Full adhesive bond strength is reached after 1–4 days, depending on humidity and temperature. Dries within 24 hours under normal drying conditions [70ºF (21ºC), 50% RH]. Cold and/or humid weather may extend drying time. Parex USA Accel-Pak may be added to decrease drying time. See Data sheet for more information.

CLEAN-UP: Water-soluble prior to drying. Clean tools and containers with water before mixture sets.

121 Dry Basecoat & Adhesive

FacilitiesFrench Camp, CANorth Hollywood, CARiverside, CAColorado Springs, COHaines City, FL

Corporate OfficeParex USA, Inc.4125 E. La Palma Ave., Suite 250Anaheim, CA 92807(866) 516-0061Tech Support: (800) 226-2424

Duluth, GARedan, GAAlbuquerque, NMAllentown, PASan Antonio, TX

121 Dry Basecoat & Adhesive mixture with a trowel until the reinforcing mesh is fully embedded and the basecoat thickness is approximately 1/16 in. (1.5mm). The color of the reinforcing mesh should not be visible at the surface of the 121 Dry Basecoat & Adhesive material. A slight pattern of the mesh is acceptable, due to shrinkage of the cementitious Basecoat upon drying.

n As a leveler or filler: Apply Parex 121 Dry Basecoat & Adhesive and trowel to a smooth, uniform surface. Maximum thickness in a single application should be no more than 1/4 in. (6 mm).

LIMITATIONS:n Ambient and surface temperature

must be 40°F (4°C) or higher during application and curing time. Provide supplemental heat and protection from precipitation as needed.

n Use only on surfaces that are sound, clean, dry, unpainted (10% or less) and free from any residue which may affect the ability of the 121 Dry Basecoat & Adhesive to bond to the surface.

n Application in direct sunlight in hot weather will significantly reduce open time for embedding Parex reinforcing mesh and smoothing the surface.

n Do not use as a leveler for EPS. Rasp EPS level.

WARNING:n Read complete warning information

printed on product container prior to use. For medical emergency information, call 1-800-424-9300.

n For more information on handling this product refer to its Material Safety Data Sheet (MSDS). The most current MSDS and Product Data Sheet (PDS) can be found on our website.

n This Product Data Sheet has been prepared in good faith on the basis of information available at the time of publication. It is intended to provide users with information about the guidelines for the proper use and application of the covered product(s) under normal environmental and working conditions. Because each project is different, Parex USA, Inc. cannot be responsible for the consequences of variations in such conditions, or for unforeseen conditions.

COVERAGE:Depending on the condition of the substrate and method of application, approximate coverages per bag are:n As an adhesive:

5/16 in. (8mm) notched trowel: 130-140 ft2 (12-13 m2) 5/8 in. (16mm) notched trowel: 92-100 ft2 (8-9 m2)

n WaterMaster 1/2 in. (12.7mm) notched trowel:

113-120 ft2 (10.5 - 11.2 m2)n As a basecoat to embed 355 Parex

USA Standard Mesh: 75-95 ft2 (7-9 m2)

n As a double-layer basecoat to embed 355 Parex USA Standard Mesh and 358.20 Ultra High Impact Mesh: 35-55 ft2 (3.3-5.1 sq. m2)

n As a leveler, coverage depends upon the thickness applied.

CONTAINER:50 lbs. (22.7 kgs) net weight in multiwall moisture-resistant bags.n Storage: Store off the ground and

protect from sun and moisturen Shelf life: 12 months if properly stored

in the original unopened container.

SURFACE PREPARATION:n Planar irregularities are limited to

1/4 in. (6mm) or less in a 4 ft. (1.22 m) radius. Surface irregularities are limited to 1/4 in. (6mm) or less for masonry and concrete and 1/8 in. (3mm) or less for sheathing.

n Irregular and uneven surface should be filled with any Parex 121 Basecoat & Adhesive.

n Remove surface contaminants such as dust or dirt without damaging the substrate.

n Painted substrates must have the paint removed with methods that result in no more than 10% of the remaining surface having paint.

n For additional options for surface preparation, contact Parex USA Technical Services Department.

MIXING:n Use clean equipment for mixing

and preparation.n Add 5-6 quarts (4.7-5.7 L) of cool

clean potable water to a 5 gal pail. Add half of the amount of 121 Dry Basecoat & Adhesive and mix to a

homogenous consistency using a heavy-duty 1/2 in. (13 mm) drill with a rust-free paddle at 400-500 rpm. Then add the remaining half and mix until consistent.

n Small amounts of cool clean potable water may be added to adjust workability.

n Let the mixture stand for five minutes after initial mixing, then stir again, adding small amounts of water for workability once only.

n Parex 121 Dry Basecoat & Adhesive should be used immediately after mixing.

n Half batches may be mixed for convenience.

n Only Parex USA approved additives can be added to this product.

APPLICATION:n Read the entire label before using

this product.n Adhesive Application: Apply the

121 Dry Basecoat & Adhesive to the entire surface on one face of the insulation board, using a 5/8 in. (16mm) notched trowel for masonry and concrete, or a 1/2-in. notched trowel for the Standard WaterMaster System, or a 5/16 in. (8mm) notched trowel for sheathing. The adhesive ribbons should be of uniform thickness, run vertically when positioned on the wall (parallel to the 2 ft. [61 cm] board dimension), and reach the perimeter of the insulation board. To ensure high initial grab and uniform adhesive contact, apply insulation board to the wall with firm pressure to the entire surface. Apply sufficient pressure to flatten adhesive ridges. Glass mat sheathing requires extra pressure.

n Basecoat Application: Rasp EPS board after 24 hours and when adhesive has fully cured and bonded. Using a stainless steel trowel, apply the 121 Dry Basecoat & Adhesive mixture to the rasped surface of the insulation board to a uniform thickness of 1/16 - 3/32 in. (1.5 - 2.4mm). Embed the Parex reinforcing mesh immediately in the wet 121 Dry Basecoat & Adhesive mixture. Smooth the surface of the

© Parex USA, Inc. June 2012 • P121DDS

DESCRIPTION USES

Reinforcing Meshes

355 Standard MeshStandard reinforcement of Parex USA EIFS walls for impact resistance and used in Parex USA Stucco Krak-Shield assemblies.

4.5 oz fiberglass 38 in. (96.5cm) wide mesh. Highly flexible for full walls or details. Alkali-resistant.

356 Short Detail MeshBackwrapping , corners, reveals and trim.4.5 oz fiberglass mesh 9.5 in. (24cm)

wide. Highly flexible for details. Alkali-resistant.

352 Adhesive MeshComplex architectural details only.4.5 oz fiberglass mesh. Self-adhesive,

facilitates the wrapping of complex contours. Highly flexible for details. Alkali-resistant.

358.10 Intermediate Impact MeshUse with Parex USA EIFS to achieve EIMA/ASTM medium-impact strength classification. Used in Parex USA Stucco Krak-Shield assemblies.

12 oz fiberglass 38 in. (96.5cm) wide mesh. Intermediate strength to enhance impact and abuse resistance. Alkali-resistant.

358.14 High Impact MeshUse with Parex USA EIFS to achieve EIMA/ASTM high-impact strength classification.

15 oz fiberglass 38 in. (96.5cm) wide mesh. High strength to enhance impact and abuse resistance. Alkali resistant.

358.20 Ultra High Impact MeshUse with Parex USA EIFS to achieve EIMA/ASTM ultra-high impact strength classification. 355 Standard Mesh must be used in combination with 358.14 High Impact Mesh for Impact Resistance

20 oz fiberglass 38 in. (96.5cm) wide mesh. Ultra high strength to enhance impact and abuse resistance. Alkali-resistant.

Parex USA Reinforcing Meshes have been tested within the Parex USA EIFS Systems for compliance to Chapter 26 of the International Building Code.

Alkali resistant is defined as 120 pli (21 dN/cm) retained tensile strength per ASTM E 098 after 28 days soaked in 5% sodium hydroxide solution.

357 Corner MeshCorner reinforcement, required with 358.20 Ultra High Impact Mesh. 355 Standard Mesh must be used in combination with 358.20 High Impact Mesh for Impact Resistance of corners.

7.2 oz fiberglass 9.5 in (24cm) wide mesh. Heavy duty. Factory pre-bent to fold uniformly around corners. Designed to enhance impact and abuse resistance at corners. Alkali-resistant.

355.48 Long Standard MeshStandard reinforcement of Parex USA EIFS walls for impact resistance and used in Parex USA Stucco Krak-Shield assemblies.

4.5 oz fiberglass mesh 48 in (121.9cm) wide. Highly flexible for details. Alkali-resistant.

ASTM E2486 Impact Classification (formerly EIMA 101.86)

A. Standard Impact Resistance, 25-49 in-lbs (2.8 - 5.6 J) Impact RangeB. Medium Impact Resistance, 50-89 in-lbs (5.7-10.1 J) Impact RangeC. High Impact Resistance, 90-150 in-lbs (10.2-17.0 J) Impact RangeD. Ultra High Impact Resistance, >150 in-lbs (> 17.0 J) Impact Range

© Parex USA, Inc. October 2012 • PUSARMDS

FacilitiesFrench Camp, CANorth Hollywood, CARiverside, CAColorado Springs, COHaines City, FL

Corporate OfficeParex USA, Inc.4125 E. La Palma Ave., Suite 250Anaheim, CA 92807(866) 516-0061Tech Support: (800) 226-2424

Duluth, GARedan, GAAlbuquerque, NMAllentown, PASan Antonio, TX

Product Nominal Weight Coverage Width Length Packaging

355 Standard Mesh 4.5 oz/yd² (153g/m²) 475 ft² (43.6 m²) 38 in (96.5cm) 150' 4 rolls/box

355.48 Long Standard Mesh 4.5 oz/yd² (153g/m²) 600 ft² (55.7 m²) 48 in (122cm) 150' 4 rolls/box

356 Short Detail Mesh 4.5 oz/yd² (153g/m²) 119 ft² (11 m²) 9.5 in (24cm) 150' 16 rolls/box

352 Adhesive Mesh 4.5 oz/yd² (153g/m²) 237 ft² (21.7m²) 19 in (48.2cm) 150' 8 rolls/box

Imp

act 358.10 Intermediate Impact Mesh 12 oz/yd² (407 g/m²) 237 ft² (21.7m²) 38 in (96.5cm) 75' 4 rolls/box

358.14 High Impact Mesh 15 oz/yd² (509g/m²) 237 ft² (21.7m²) 38 in (96.5cm) 75' 2 rolls/box

358.20 Ultra High Impact Mesh 20 oz/yd² (692g/m²) 237 ft² (21.7m²) 38 in (96.5cm) 75' 2 roll/box

Spec

ialt

y

357 Corner Mesh 7.2 oz/yd² (244g/m²) 119 ft² (11 m²) 9.5 in (24cm) 150' 4 rolls/box

Impact: Where mesh edges butt together, the joint has to be covered with a layer of Standard or Detail mesh with a minimum lap of 4 in. (102mm). For 358.14 High Impact Mesh and 358.20 Ultra High Impact Mesh, a second layer of 355 Standard Mesh must be applied on the whole surface.

n 357 Corner Mesh: The fiberglass mesh must be embedded into the wet base coat and be smoothed with a trowel until fully embedded with the mesh color not visible. A slight pattern of the mesh is acceptable, due to shrinkage of the cementitious basecoat. Tightly butt mesh edges but do not overlap them. Install mesh taking care to avoid wrinkles. Where mesh edges butt together, the joint has to be covered with a layer of Standard or Detail mesh with a minimum lap of 6 in. (152mm)

APPLICATION: n 354 Standard Mesh 4.8oz,

355 Standard, 355.48 Long Standard and 356 Short Detail Mesh: The fiberglass mesh must be embedded into a Parex USA basecoat and be smoothed with a trowel until mesh is fully embedded and the basecoat, thickness is approximately 1/16 in. (1.5mm). The color of the reinforcing mesh should not be visible at the surface of the Parex USA basecoat material. A slight pattern of the mesh is acceptable, due to shrinkage of the cementitious basecoat upon drying. Install mesh taking care to avoid wrinkles. The mesh must be continuous at all corners and must be lapped a minimum of 2-1/2 in. (63.5mm) at the mesh seams.

n 352 Adhesive Mesh: 352 Adhesive Mesh is adhered to the EPS board before the basecoat is applied. Apply the basecoat and smooth it with a trowel until the mesh color is not visible. A slight pattern of the mesh is acceptable, due to shrinkage of the cementitious basecoat. The mesh must be continuous at all corners and must be lapped a minimum of 2-1/2 in. (63.5 mm) at the mesh seams.

n 358.10 Intermediate Impact, 358.14 High Impact, and 358.20 Ultra High Impact Mesh: The fiberglass mesh must be embedded into the wet basecoat and be smoothed with a trowel until fully embedded with the mesh color not visible. Tightly butt mesh edges but do not overlap them. Install Parex USA 357 Corner Mesh at all edges. 358.10 Intermediate

Section: 09200

800.327.7077www.plasticomponents.com

November 2008

A-4inc.

TM Caulk all butt joints, intersections and ends.

Stucco and Plaster

Application:To be used in any area where a banding/pop out or “quoin”detail is desired. “T” bar design adds strength and willreduce “waving” with the extra thickness of the stucco.Specification:Casing Beads shall be Plastic Components, Inc.#________. All exterior accessories shall be ofPVC material conforming toASTM standards D1784, C1063and D4216. They shall be used where specified by thearchitect and installed per industry standards.

1-3/4"(44 m)

3/16"(5 mm)

“T” Bar

1-3/4"(44 mm)3/16"

(5 mm)

Application:Engineered for use at any area where thicker amounts ofstucco are specified, eg: “quoins”, bands, or popouts.Specification:Old Style Casing Bead shall be Plastic Components, Inc.#________. All exterior accessories shall be ofPVC material conforming to ASTM standards D1784, C1063and D4216. They shall be used where specified by the archi-tect and installed per industry standards.

Product Ground Dimensions/Descriptions PiecesNumber Per Box

1100 1" (25 mm) 50

1125 1-1/4" (32 mm) 50

1150 1-1/2" (38 mm) 50

1200 2" (51 mm) 40

“T” Bar Casing Bead

10' (3 m) Lengths

“T” bar casing bead,1-3/4" (44 mm) wideperforated flange.Designed for extrastrength.

Product Ground Dimensions/Descriptions PiecesNumber Per Box

1100-O 1" (25 mm) 50

1125-O 1-1/4" (32 mm) 50

1150-O 1-1/2" (38 mm) 50

1200-O 2" (51 mm) 40

Old Style Casing Bead

10' (3 m) LengthsAdd suffix “WP” to order with weep holes. Example: 1100-OWP

Old style casing bead,1-3/4" (44 mm) wideperforated flange.

Section: 09200

800.327.7077www.plasticomponents.com

September 2008

A-1inc.

TM

Stucco and Plaster

Caulk all butt joints, intersections and ends.

Application:Provides a rustproof, high-impact-resistant non-kinking corner.The design of the hole pattern in the flanges allows the stuccoto flow through forming a solid layer giving the corner extrastrength. Larger holes in the nailing flange make it easier toinstall when using stub nails.

Specification:Corner Bead shall be Plastic Components, Inc. #________.All exterior trim shall be of PVC material conforming to ASTMstandards D1784, C1063 and D4216. They shall be used wherespecified by the architect and installed per industry standards.

1A

1B

2

3

2-1/2"(64 mm)

2-3/4"(70 mm)

1-1/2"35 mm)

2-1/2"(64 mm)

1-1/2"(35 mm)

2-1/2"(64 mm)

2-1/2"(64 mm)

BN1A

Corner Bead

8' & 10' (2.5 m & 3 m) Lengths

Product Dimensions/Descriptions PiecesNumber Per Box

1A 2.5" (64 mm) x 2.5" (64 mm) 50

1B 1.5" (38 mm) x 1.5" (38 mm) 50

2 2.75" (70 mm) x 2.75" (70 mm) 50

3 2.5" (64 mm) x 1.5" (38 mm) 50

1A4 4" (102 mm) x 4" (102 mm) 30

1A135 2.5" (64 mm) x 2.5" (64 mm) angled flange 50

BN1A 2.5" (64 mm) x 2.5" (64 mm) bullnose flange 20

FACT-DATA

©

MANUFACTURER FORTA CORPORATION, 100 Forta Drive, Grove City, PA, U.S.A., 16127-6399

TELEPHONE: 1-800-245-0306, (724) 458-5221; FAX: (724) 458-8331; www.forta-ferro.com

GENERAL DESCRIPTION FORTA STUCCO-BOND® is an easy to apply and finish, fully oriented, 100% virgin homopolymer polypropylene monofilament fibrous reinforcement. This engineered fiber provides a mini-reinforcing system forming a more cohesive, inner-supported mix that functions as a plastic shrinkage reinforcement intended to reduce the formation of shrinkage cracks prior to initial set. FORTA STUCCO-BOND is non-corrosive, non-magnetic, chemically inert, and 100% Alkali Proof! APPLICATIONS FORTA STUCCO-BOND® is used in interior or exterior mortar and stucco applications to control plastic shrinkage cracking while improving basic durability properties. Requires No Mix Design or Placement Changes! INSTALLATION Recommended standard dosage rate of FORTA STUCCO-BOND® is 4 to 6 oz. per 100 pounds of stucco/ mortar added directly to the mixing system during, or after, the batching of the other ingredients and mixed at the time and speed recommended by the mixer manufacturer (usually four to five minutes). PHYSICAL PROPERTIES Materials………….….Virgin Homopolymer Polypropylene Color……………………..White Form………………….Monofilament Fiber Acid/Alkali Resistance….Excellent Specific Gravity……..0.91 Absorption ………………Nil Tensile Strength…….83-96 ksi. (570-660 MPa) Compliance………………A.S.T.M. C-1116 Length…………..…...1/2” (13mm) AVAILABILITY FORTA STUCCO-BOND® can be purchased from FORTA Corporation or an authorized FORTA® products distributor, dealer or representative. Orders are shipped within 24 hours by small package services, commercial carrier, or air freight. PACKAGING DOMESTIC INTERNATIONAL Bags……………………………….………..1.0 Pounds 0.6 kg. Cartons……………………………………..40 Bags 30 Bags Pallets………………………………………16 Cartons/640 Bags 12 Cartons/360 Bags WARRANTY FORTA® products are warranted to be free of defects in material and meet all quality control standards set by the manufacturer. FORTA Corporation specifically disclaims all other warranties, express or implied. The exclusive remedy for defective product shall be to replace the product or refund the purchase price. No agent or employee of this company is authorized to vary the terms of this warranty notice. FORTA Corporation has no control over the design, production, placement, or testing of the concrete products in which FORTA® products are incorporated, and therefore FORTA Corporation disclaims liability for the end product. FORTA Corporation’s technical recommendations regarding synthetic fiber characteristics are based on years of engineering research and scores of concrete projects. FORTA® has developed a simple “4-C’s” formula to help the specifier choose the right fiber for any concrete project application. By making a decision with each of the FORTA® “4-C’s” categories – Configuration, Chemistry, Contents, and Correct Length–specifiers are assured of obtaining the desired fiber performance level for a given project. The following 4-C’s Formula Specification has been prepared to accommodate the stated reinforcement objective for this FORTA® product grade.

REINFORCEMENT OBJECTIVE: To inhibit concrete cracking caused by plastic shrinkage that occurs prior to initial set. DIVISION – CONCRETE SECTION – CONCRETE REINFORCEMENT SUB-SECTION – SYNTHETIC FIBROUS REINFORCEMENT Synthetic fibrous reinforcement shall be used in the areas denoted in plans, and shall comply with the following fiber characteristics:

1. Configuration – Fiber shall be in monofilament form. 2. Chemistry – Fiber shall be made of 100% virgin materials in the form of fully-oriented

polypropylene. 3. Contents – Fiber shall be used at a minimum dosage rate of 4 to 6 oz. per 100 pounds of

stucco/mortar. 4. Correct Length – Fiber Length shall be 1/2” (13mm).

Compliance: Fibers shall comply with A.S.T.M. C-1116 “Standard Specification for Fiber Reinforced

Concrete and Shotcrete” and applicable national building code. The approved product is FORTA

STUCCO-BOND® as manufactured by FORTA Corporation, Grove City, PA, U.S.A. Phone: 1-800-245-0306

or 1-724-458-5221; Fax: 1-724-458-8331.

FORTA Corporation 100 Forta Drive, Grove City, PA 16127-6399 U.S.A.

1-800-245-0306 or 1-724-458-5221 Fax: 1-724-458-8331 www.forta-ferro.com

FORTA®, STUCCO-BOND®, and are registered trademarks of FORTA Corporation.

6638L 3/8"

2-1/2" flange widthperforated flange

75

6650L 1/2" 75

6658L 5/8" 75

6675L 3/4" 50

6678L 7/8" 50

66100L 1" 50Long Flange Casing Beads – Terminate stucco & plaster againstdoors, windows and other dissimilar materials. Used in thoseconditions that require a longer flange.

Caulk all intersections, butt joints, ends and corners at time of installation.

66100 “T” 1"

1-3/4" flange widthperforated flange

75

66125 1-1/4" 50

66150 1-1/2" 50

66175 1-3/4" 40

66200 2" 40“Bandmaker™ Series” Casing Beads – Designed with a reinforcing rib toassist in keying heavy material fills, when “Bands” are used in architecturaldesigns.

Caulk all intersections, butt joints, ends and corners at time of installation.

Stucco & Plaster

Stucco & Plaster Accessories All products conform to ASTM D1784 cell classification 13244C

For More Information Call Toll Free 1-800-648-4695 or Visit www.vinylcorp.com1-8

Long Flange Casing Beads/Plaster Stops PRODUCTNUMBER GROUND DIMENSIONS

PIECESPER BOX

Bandmaker™ Series Casing Beads PRODUCTNUMBER GROUND DIMENSIONS

PIECESPER BOX

6650XL 1/2"

5" flange widthperforated flange

40

6658XL 5/8" 40

6675XL 3/4" 40

6678XL 7/8" 40

66100XL 1" 25

66125XL 1-1/4" 25

66150XL 1-1/2" 20

66175XL 1-3/4" 20

66200XL 2" 20XL Long Flange Casing Beads – Same as our Long Flange CasingBeads with wider perforated flange.

Caulk all intersections, butt joints, ends and corners at time of installation.

XL Long Flange Casing Beads/Plaster Stops PRODUCTNUMBER GROUND DIMENSIONS

PIECESPER BOX

6625 1/4"

1-3/4" flange widthperforated flange

100

6638 3/8" 100

6650 1/2" 100

6658 5/8" 100

6675 3/4" 75

6678 7/8" 75

66100 1" 75Casing Beads – Terminate stucco & plaster against doors, windows anddissimilar materials.

Caulk all intersections, butt joints, ends and corners at time of installation.

Casing Beads/Plaster Stops PRODUCTNUMBER GROUND DIMENSIONS

PIECESPER BOX

VinylCorp_Sec01_08-09:VinylCorp_2011 7/1/11 11:39 AM Page 1-8