afsc 2a6x6 aircraft electrical and environmental systems
Click here to load reader
Transcript of afsc 2a6x6 aircraft electrical and environmental systems
DEPARTMENT OF THE AIR FORCE CFETP 2A6X6Headquarters US Air Force Parts I and IIWashington, DC 20330-1030 October 2002
AFSC 2A6X6
AIRCRAFT ELECTRICAL ANDENVIRONMENTAL SYSTEMS
CAREER FIELD EDUCATIONAND TRAINING PLAN
CFETP 2A6X6, October 2002
1
CAREER FIELD EDUCATION AND TRAINING PLANAIRCRAFT ELECTRICAL & ENVIRONMENTAL SYSTEMS
AFSC 2A6X6, OCTOBER 2002
Table of ContentsPART I Page #Preface 2
Abbreviations/Terms Explained 3
Section A--General Information 5Purpose of the CFETPUse of the CFETPCoordination and Approval of the CFETP
Section B--Career Progression and Information 6Specialty DescriptionSkill/Career Progression
Apprentice Level (3)Journeyman Level (5)Craftsman Level (7)Superintendent Level (9)
Training DecisionsCommunity College of the Air ForceCareer Field PathBase/Unit Education and Training Manager Checklist
Section C--Skill Level Training Requirements 13PurposeTraining Requirements
Apprentice Level (3)Journeyman Level (5)Craftsman Level (7)Superintendent Level (9)
Section D--Resource Constraint 15
PART IISection A, Specialty Training Standard (STS) 15
Section B, Course Objective List 262
Section C, Support Material 263
Section D, Training Course Index 264
Section E, MAJCOM Unique Requirements 271
Supersedes: CFETP 2A6X6, Aug 2000 Certified by: HQ USAF/ILMM (CMSgt McMahan)Number of Printed Pages: 273OPR: 364 TRS/TRR (Dale Chitwood, GS-12)(DSN 736-2772/EMAIL [email protected])
CFETP 2A6X6, October 2002
2
AIRCRAFT ELECTRICAL AND ENVIRONMENTAL SYSTEMS SPECIALTYCAREER FIELD EDUCATION AND TRAINING PLAN
AFSC 2A6X6OCTOBER 2002
PART I
PREFACE
1. This Career Field Education and Training Plan (CFETP) is a comprehensive education and trainingdocument that identifies life-cycle education/training requirements, training support resources, and minimumcore task requirements for 2A6X6, Aircraft Electrical and Environmental Systems Specialty. The CFETP willprovide personnel a clear career path to success and instills rigor in all aspects of career field training. ThisCFETP supersedes 2A6X6 CFETP, August 2000.
NOTE: Civilians occupying associated positions will use Part II to support duty position qualification training.
2. The CFETP consists of two parts. Supervisors will use both parts to plan, manage, and control training .
2.1 Part I provides information necessary for overall management of the specialty. Section A explains howeveryone will use the plan. Section B identifies career field progression information, duties and responsibilities,training strategies, and career field path. Section C associates each level with specialty qualifications(knowledge, education, training, and other). Section D indicates resource constraints to accomplishing this plan,such as funds, manpower, equipment, and facilities. Section E identifies transition training guide requirementsfor SSgt through MSgt.
2.2 Part II includes the following: Section A identifies the Specialty Training Standard (STS) and includesduties, tasks, technical references to support training; Air Education and Training Command (AETC) conductedtraining, wartime course/core task and correspondence course requirements; Section B contains the courseobjective list/training standards supervisors will use to determine if airmen have satisfied training requirements;Section C identifies available support materials, such as Qualification Training Package (QTP) which may bedeveloped to support proficiency training. These packages are indexed in AFIND8, Numerical Index ofSpecialized Educational Training Publications; Section D identifies a training course index supervisors can useto determine if resources are available to support training. Included here are both mandatory and optionalcourses; Section E identifies MAJCOM unique training requirements supervisors can use to determineadditional training required for the associated qualification needs.
3. Using guidance provided in the CFETP will ensure individuals in this specialty receive effective and efficienttraining at the appropriate point in their career. This plan will enable us to train today’s work force fortomorrow’s jobs. At unit level, supervisors and trainers will use Part II to identify, plan, and conduct trainingcommensurate with the overall goals of this plan.
CFETP 2A6X6, October 2002
3
ABBREVIATIONS/TERMS EXPLAINED
Advanced Training. Formal course which provides individuals who are qualified in their Air Force Specialty(AFS) with additional skills/knowledge to enhance their expertise in the career field. Training is for selectedcareer airmen at the advanced level of an AFS.
Air Force Job Qualification Standard (AFJQS). A comprehensive task list that describes a particular jobtype or duty position. Supervisors use the AFJQS to document task qualifications. The tasks of AFJQS arecommon to all persons serving in the described duty position.
Career Field Education and Training Plan (CFETP). A CFETP is a comprehensive, multipurpose documentcovering the entire spectrum of education and training for a career field. It outlines a logical growth plan thatincludes training resources and is designed to make career field training identifiable, to eliminate duplication,and to ensure this training is budget defensible.
Continuation Training. This is additional training that exceeds minimum upgrade requirements and has anemphasis on present or future duty assignments.
Core Task. Tasks that the Air Force Career Field Manager (AFCFM) identifies as minimum qualificationrequirements within an Air Force Specialty. Only a percentage of critical tasks for each system are listed asmandatory core tasks. This gives units needed flexibility to manage their workforce training. Core tasksidentified with *R are optional for ANG and AFRC.
Course Objective List (COL). A publication identifying the tasks and knowledge requirements, and respectivestandards provided to achieve a 3-/7-level in this career field. Supervisors use the COL to assist in conductinggraduate evaluations in accordance with AFI 36-2201, Developing, Managing and Conducting TrainingPrograms
Enlisted Specialty Training (EST). A mix of formal training (technical school) and informal training (on-the-job) to qualify and upgrade airmen in each skill level of a specialty.
Exportable Training. Additional training via computer assisted, paper text, interactive video, or othernecessary means to supplement training.
Field Technical Training (Type 4). Special or regular on-site training conducted by a training detachment(TD) or by a mobile training team (MTT).
Initial Skills Training. A formal school course that results in the award of a 3-skill level AFSC.
Instructional System Development (ISD). A deliberate and orderly process for developing, validating, andreviewing instructional programs that ensures personnel are taught the knowledge and skills essential forsuccessful job performance.
Occupational Survey Report (OSR). A detailed report showing the results of an occupational survey of tasksperformed within a particular AFS.
On-the-Job Training (OJT). Hands-on, over-the-shoulder training at the duty location used to certifypersonnel for both skill level upgrade and duty position qualification.
CFETP 2A6X6, October 2002
4
Qualification Training (QT). Actual hands-on task performance training designed to qualify an airman in aspecific duty position. This training program occurs both during and after the upgrade training process. It isdesigned to provide the performance skill/knowledge training required to do the job.
Qualification Training Package (QTP). An instructional course designed for use at the unit to qualify or aidqualification in a duty position or program or on a piece of equipment. It may be printed, computer based, or inother audiovisual media.
Resource Constraints. Resource deficiencies, such as money, facilities, time, manpower, or equipment, thatprecludes desired training from being accomplished.
Specialty Training Standard (STS). An Air Force publication that describes an Air Force Specialty in termsof tasks and knowledge an airman may be expected to perform or to know on the job. It serves as a contractbetween AETC and the functional user to show which of the overall training requirements for an AFSC aretaught in formal schools, Career Development Courses, and exportable courses.
Training Setting. The type of forum in which training is provided (formal resident school, on-the-job, fieldtraining, mobile training team, self-study, etc.).
Upgrade Training. A mixture of mandatory courses, task qualification, QTPs, and CDCs required for award ofthe 3-, 5-, 7-, or 9-skill levels.
Utilization and Training Workshop (U&TW). A forum, co-chaired by the AFCFM and Training PipelineManager (TPM), of MAJCOM Air Force Specialty Code (AFSC) functional managers, Subject Matter Experts(SMEs), and AETC training personnel that determines career ladder training requirements.
CFETP 2A6X6, October 2002
5
SECTION A - GENERAL INFORMATION
1. Purpose of the CFETP. This CFETP provides the information necessary for Air Force Career FieldManager (AFCFM), MAJCOM functional managers (MFMs), commanders, training managers, supervisors, andtrainers to plan, develop, manage, and conduct an effective career field training program. This plan outlines thetraining that individuals in AFSC 2A6X6 should receive in order to develop and progress throughout theircareer. This CFETP identifies initial skill, upgrade, qualification, advanced, and proficiency training. Initialskills training is the AFS specific training an individual receives upon entry into the Air Force or upon retraininginto this specialty for award of the 3-skill level. This training is conducted by AETC at Sheppard AFB, TX.Upgrade training identifies the mandatory courses, task qualification requirements, and correspondence coursecompletion requirements for award of the 3-, 5-, 7-, 9-skill levels. Qualification training is actual hands-on taskperformance training designed to qualify an airman in a specific duty position. This training program occursboth during and after the upgrade training process. It is designed to provide the performance skills/knowledgerequired to do the job. Advanced training provides individuals who are qualified in their Air Force Specialty(AFS) with additional skills/knowledge to enhance their expertise in the career field. . Proficiency training isadditional training, either in-residence or exportable advanced training courses, or on-the-job training, providedto personnel to increase their skills and knowledge beyond the minimum required for upgrade. The CFETP hasseveral purposes, some are:
1.1. Serves as a management tool to plan, manage, conduct, and evaluate a career field training program. Also,it is used to help supervisors identify training at the appropriate point in an individual’s career.
1.2. Identifies tasks and knowledge training requirements for each skill level in the specialty and recommendseducation/training throughout each phase of an individual's career.
1.3. Lists training courses that are available in the specialty and identifies sources of training, and the trainingdelivery method.
1.4. Identifies major resource constraints which impact full implementation of the desired career field trainingprocess.
2. Use of the CFETP. This CFETP will be used by MFMs and supervisors at all levels to ensurecomprehensive and cohesive training programs are available for each individual in the specialty.
2.1. AETC training personnel will develop/revise formal resident, non-resident, Training Detachment (TD), andexportable training based upon requirements established by the users and documented in Part II of the CFETP.They will also work with the AFCFM to develop acquisition strategies for obtaining the resources needed toprovide the identified training.
2.2. MFMs will ensure their training programs complement the CFETP mandatory initial, upgrade, andproficiency requirements. OJT, resident training, contract training, or exportable courses can satisfy theseidentified requirements. MAJCOM developed training, to support this AFSC, must be identified for inclusionin this plan and must not duplicate other available training resources.
2.3. Each individual will complete the mandatory training requirements specified in this plan. The list ofcourses in Part II will be used as a reference to support training.
CFETP 2A6X6, October 2002
6
3. Coordination and Approval. The AFCFM is the approval authority. The using MAJCOM representativesand AETC training personnel will identify and coordinate on the career field training requirements. The AETCtraining manager for AFSC 2A6X6 will initiate an annual review of this document by AETC and MFM toensure currency and accuracy. Using the list of courses in Part II, they will eliminate duplicate training.
SECTION B - CAREER FIELD PROGRESSION AND INFORMATION
4. Specialty Descriptions.
4.1. Specialty Summary. The Aircraft Electrical & Environmental Specialist performs and supervises aircraftelectrical and environmental (E&E) functions and activities. Troubleshoots, inspects, removes, installs, repairs,modifies, overhauls, and operates aircraft E & E systems, components, and associated support equipment.Related DoD Occupational Subgroup: 602.
4.2. Duties and Responsibilities:4.2.1. Aircraft Electrical and Environmental Systems Apprentice and Journeyman: Inspects,troubleshoots, installs, and maintains aircraft power and air distribution systems, subsystems, components, andtest equipment using proper technical publications. Visually and operationally tests aircraft electrical andenvironmental systems and components. Systems maintained include direct and alternating current powersystems; aircraft landing, anti-skid, and steering systems; flight and fuel control systems; ignition and electronicengine controls; master caution and warning panels; fire and overheat warning systems; lighting systems; andstatic and rotary inverters. Also included are systems and components such as bleed air distribution systems; airconditioning, cabin pressurization, NESA glass, and anti-icing systems; oxygen systems; fire extinguishingsystems; and turbine drive engine starters; in-flight blade inspection system (IBIS); tail skid system; cargowinch/hoist. Repairs, modifies, and overhauls batteries; electrical and solid state voltage regulators; control,protection, caution, and warning panels; frequency and load, and NESA glass controllers; static and rotaryinverters; transformer rectifiers; generators; actuators; relays; timing and sensing devices; systems amplifiers;fire, audible warning, and asymmetry detectors; motors; lighting equipment; cryogenic containers; and otherspecial equipment. Uses electrical and electronic meters and test equipment such as: Manometers; cabinpressure leak and temperature control system testers; thermal switch testers; anti-G suit valve testers; air turbinemotor testers; liquid oxygen system testers; multimeters; and ammeters. Services, inspects, and overhauls liferaft inflation equipment. Replaces, fabricates, or modifies electrical wiring and connectors. Checks for andtreats corrosion. Inspects, services, and performs general aircraft handling procedures. Uses technical orders andschematic diagrams to isolate malfunctions. Maintains inspection and maintenance records. Records pertinentdata on equipment maintenance data collection (MDC) forms and/or enters data into automated maintenancedata systems. Recommends methods to improve equipment performance and maintenance procedures.Handles, labels, and disposes of hazardous materials and waste according to environmental standards.4.2.2. Aircraft Electrical and Environmental Systems Craftsman: Inspects, analyzes, troubleshoots, andmaintains aircraft electrical and environmental systems, associated components, subsystems, and testequipment. Advises on problems operating and maintaining aircraft electrical and environmental systems,associated electronic components, subsystems, and test equipment. Solves maintenance problems using wiringdiagrams, schematic diagrams, and technical publications by analyzing operating characteristics of electrical andenvironmental systems. Determines proper maintenance procedures to repair and return systems andcomponents to maximum efficiency. Diagnoses malfunctions and recommends corrective actions. Checksinstalled and repaired components to ensure compliance with technical publications and directives. Evaluatesrequirements and prepares quality deficiency reports. Supervises and evaluates job performance and
CFETP 2A6X6, October 2002
7
maintenance techniques used to interpret, operate, troubleshoot, remove, repair, service, overhaul, and installaircraft electrical and environmental systems and components. Provides training and task certification for skilllevel advancement. Ensures compliance with published safety guidelines. Ensures hazardous materials andwaste are handled, stored, and disposed of according to environmental standards.4.2.3. Maintenance Superintendent: Manages maintenance and staff functions on aircraft electrical andenvironmental, hydraulic, fuel, and aircrew egress systems. Interprets and evaluates directives and publications,inspection findings, records, and reports and recommends corrective actions. Determines operational status andevaluates operational effectiveness of aircraft and associated systems. Inspects and evaluates maintenanceactivities and resolves problems. Interprets and establishes safety and training guidelines. Plans, organizes,directs, and controls troubleshooting and repair activities of maintenance personnel. Establishes priorities forcompletion of maintenance tasks and provides assistance in solving maintenance, supply, and personnelproblems. Performs supervisory inspections of, and directs maintenance actions on aircraft systems andcomponents. Evaluates aircraft and system failures to determine need to submit quality deficiency reports.Controls resources, funds, and cost management. Manages handling, storing, and disposing of hazardous mate-rials and waste according to environmental standards.
5. Career Skill Progression. Adequate training and timely progression from the apprentice to thesuperintendent skill level play an important role in the Air Force's ability to accomplish its mission. It isessential that everyone involved in training do their part to plan, develop, manage, and conduct an effectivetraining program. The guidance provided in this part of the CFETP will ensure each individual receives viabletraining at appropriate points in their career
5.1. Apprentice (3-level): Upon completion of initial skills training, a trainee will work with a trainer toenhance their knowledge and skills. They will utilize the Career Development Course, Task QualificationTraining, and available exportable courses for continued advancement. Once task certified, a trainee mayperform the task unsupervised. Apprentices can be considered for appointment as unit trainers after completionof a formal trainer course.
5.2. Journeyman (5-level). Once upgraded to the 5-level, the journeyman will enter into continuation trainingto broaden their experience base by increasing their knowledge and skill in troubleshooting and solving morecomplex problems. Five-levels may be assigned job positions such as quality assurance and various staffpositions. After having 48 months in the Air Force, 5-levels will attend Airman Leadership School (ALS) toenhance their Professional Military Education (PME). Five-levels will be considered for appointment as unittrainers. Individuals will use their CDCs to prepare for Weight Airman Promotion testing. They should alsoconsider continuing their education toward a Community College of the Air Force (CCAF) degree.
5.3. Craftsman (7-level): A craftsman can expect to fill various supervisory and management positions suchas shift leader, element chief, expediter, section chief, and task certifier. They can also be assigned to work instaff positions. Craftsmen should take courses to obtain added knowledge on management of resources andpersonnel. Continued academic education through CCAF and higher degree programs is encouraged. Inaddition, when promoted to TSgt, individuals will complete the Noncommissioned Officer Academy.
5.4. Superintendent (9-level): A 9-level can be expected to fill positions such as flight chief, productionsupervisor, and various staff NCOIC jobs. Additional training in the areas of budget, manpower, resources, andpersonnel management should be pursued through continuing education. Individuals promoted to SMSgt willcomplete the Senior Noncommissioned Officer Academy. Additional higher education and completion ofcourses outside their career AFSC are also recommended.
CFETP 2A6X6, October 2002
8
6. Training Decisions: The CFETP uses a building block approach (simple to complex) to encompass theentire spectrum of training requirements for the Aircraft Electrical and Environmental Systems Career Field.The spectrum includes a strategy for when, where, and how to meet these training requirements. The strategymust ensure we develop affordable training, eliminate duplication, and prevent a fragmented approach totraining. The following training decisions were made by MAJCOM Functional Managers and Subject MatterExperts (SMEs) at the career field Utilization and Training Workshop held at Sheppard AFB, 3-7 December2001.
6.1. Initial Skills: The overall content of what is currently being taught in Course J3ABR2A636 008 isoutstanding. Recent GAS survey results indicate a 91% satisfaction rating by supervisors of new trainees. Athorough review of the course was accomplished to assess currency of proficiency codes, core tasks, resourceconstraints, and any other recommendations needed to improve the course. The course content basicallyremained the same. A few minor changes will be required in order to meet user needs. Those changes areinternal issues that will be addressed by the 364 Training Squadron. The establishment of new trainingrequirements created some equipment constraints. In order to eliminate/reduce those constraints, the followingequipment will be needed:
• 2 Wire Maintenance Kit• 1 New LOX Video• 2 Time Domain Reflectometer• 15 IETMs Laptops
6.2. Five-Level Upgrade Training: The following changes to the 2A656 Career Development Course areneeded:
• Volume 1 will require a supplement. A lesson on Interactive/Electronic Technical Manuals will need tobe developed and the lessons on processing and controlling material and funds management/depot levelreparable deleted.
• Volume 3 will require a rewrite. Lessons on Databus Channels/Principles operational fundamentals,troubleshooting an emergency generator system, and troubleshooting a single generator system willneed to be developed.
• Volume 5 will require a rewrite. The Oxygen cryotainer cart lesson needs draining and cleaningcomponents added, and a new lesson on Nitrogen cryotainer carts developed, that covers operationalfundamentals on a Libby or Zwick liquid cart. Removing and installing gaseous oxygen systemcomponents needs to be deleted
6.3. Seven-Level Upgrade Training.6.3.1 The following changes to the 2A676 Career Development Course are needed:
• Volume 1 will require a rewrite. A lesson on troubleshooting an emergency generator system will needto be developed. The current multi-generator lesson will be changed so as to utilized the C-17 multi-generator system. The lessons on using a Time domain reflectometer and elements of physics need to bedeleted
CFETP 2A6X6, October 2002
9
6.3.2. After reviewing Course J3ACR2A676 001, Aircraft Electrical & Environmental Systems Craftsman, thebelow deletions and additions need to be made. These changes will not reduce or added to the total time of 69hours. The changes made are as follows:
• Objective 1A ORM has been moved to objective 2A and expanded to include the 6 Steps and 7 Tools ina more in-depth explanation of the processes involved.
• Objective 2A, Explosive Safety, has been deleted. ORM has been added. Radiation Hazards has beenadded. Flight line safety during vehicle operation has been added.
• Objective 2B reflect changes from U&TW for implementation in the lesson plan. 623A documentationwhen, why and how to document has been added/
• Objective 2C, STS items A2.4.1, A2.4.2 are deleted from the course. A2.7.2, A2.7.3, A2.7.4, A2.7.5.1,A2.7.5.2, and A2.7.5.3 have been move to Objective 2D. This objective will now only include theMESL, A2.4.8, and will be reduced from 13 hours to 4 hours. Objective 2D (add) STS items A2.7.2,A2.7.3, A2.7.4, A2.7.5.1, A2.7.5.2 and A2.7.5.3 and delete A2.7.8 and A2.7.9. Increase lesson to 8hours.
• Objective 2E, Technical Order Improvement Report and Idea Program, A2.9.6 and change proficiencycode to 2b.
• Objective 3A, no changes.• Objective 3B change lesson to include 7-level students inspecting previous maintenance accomplished
by 3-level students in block 6. They will be required to brief the instructor of their findings. STS itemsA3.19.5 will change to a 3c and A3.22.1.4 will change to a 3c. The time will remain at 12 hours.
• Objective 3C, no change required.• An objective will be added covering personal accountability as a production inspector.
6.4. Proficiency Training. Any additional knowledge and skill requirements which were not taught throughinitial skills or upgrade training were assigned to continuation training. The purpose of the continuation trainingprogram is to provide additional training exceeding minimum upgrade training requirements with emphasis onpresent and future duty positions. MAJCOMSs must ensure individuals in Aircraft Electrical andEnvironmental Systems career field receive the necessary training at the appropriate point in their career.
7. Community College of the Air Force (CCAF) Academic Programs. Enrollment in CCAF occurs uponcompletion of basic military training (BMT). CCAF provides the opportunity to obtain an Associates inApplied Sciences Degree. In addition, CCAF offers the following:
7.1. Occupational Instructor Certification. Upon completion of instructor qualification training, consistingof the Basic Instructor Course (BIC) and supervised practice teaching, CCAF instructors who possess anassociates degree or higher may be nominated by their school commander/commandant for certification as anoccupational instructor.
7.2 Trade Skill Certification. When a CCAF student separates or retires, a trade skill certification is awardedfor the primary occupational specialty. The college uses a competency based assessment process for trade skillcertification at one of four proficiency levels; Apprentice, Journeyman, Craftsman/Supervisor, or MasterCraftsman/Manager. All are transcribed on the CCAF transcript.
CFETP 2A6X6, October 2002
10
7.3. Degree Requirements: All airmen are automatically entered into the CCAF program. Prior to completingan associate degree, the 5-level must be awarded and the following requirements must be met:
Semester HoursTechnical Education................................................................................................. 24Leadership, Management, and Military Studies......................................................... 6Physical Education ..................................................................................................... 4General Education .................................................................................................... 15Program Elective ...................................................................................................... 15 Technical Education; Leadership, Management, and Military Studies; or General EducationTotal ......................................................................................................................... 64
7.3.1. Technical Education (24 Semester Hours): Completion of the initial skills resident training atSheppard AFB satisfies all or part of the technical education requirement.7.3.2. Leadership, Management, and Military Studies (6 Semester Hours): Professional military educationand/or civilian management courses.7.3.3. Physical Education (4 Semester Hours): This requirement is satisfied by completion of Basic MilitaryTraining.7.3.4. General Education (15 Semester Hours): Courses must meet the definition of General Educationsubjects/courses as provided in the CCAF General Catalog.7.3.5. Program Elective (15 Semester Hours): Satisfied with applicable Technical Education; Leadership,Management, and Military Studies. Six semester hours of CCAF degree-applicable technical credit otherwisenot applicable to this program may be applied. See the CCAF General Catalog for details regarding theAssociates of Applied Science for this specialty. Additional off-duty education is a personal choice that isencouraged for all.
7.4. AETC Instructor Requirements. Individuals desiring to become an Air Education and TrainingCommand Instructor should be actively pursuing an associate's degree. It is necessary for instructors to have atleast an associate's degree so the Technical School can maintain accreditation through the Southern Associationof Colleges and Schools.
CFETP 2A6X6, October 2002
11
8. Career Field Path
8.1. Enlisted Career Path. Table 8.1 identifies career milestones for the 2A6X6 Air Force Specialty.
Table 8.1 Enlisted Career PathGrade Requirements
Education and Training Requirements Rank AverageSew-On
EarliestSew-On
High Year Of Tenure(HYT)
Basic Military Training SchoolApprentice Technical School (3-Skill Level) Amn
A1C6 months
16 monthsUpgrade To Journeyman (5-Skill Level)- Minimum 15 months on-the-job training.- Complete all 5-level core tasks on one MDS.- Complete appropriate CDC if/when available.
AmnA1CSrA
6 months16 months
3 years 28 months 10 Years
Airman Leadership School (ALS)- Must be a SrA with 48 months time in service
or be a SSgt Selectee.- Resident graduation is a prerequisite for SSgt
sew-on (Active Duty Only).Trainer
- Qualified and certified to perform the task tobe trained.
- Have attended the formal trainer’s course andappointed in writing by Commander.
Certifier- Be at least a 5-skill level SSgt; and qualified and certified
to perform the task being certified- Attend formal certifier course and appointed in writing by
Commander.- Be a person other than the trainer.
Upgrade To Craftsman (7-Skill Level)- Minimum rank of SSgt.- Complete all 5- and 7-level core tasks on one
mission design aircraft.- Complete appropriate CDC if/when available.- Advanced Technical School.- Minimum 12 months on-the-job training.
SSgt 7.5 years 3 years 20 Years
Noncommissioned Officer Academy (NCOA)- Must be a TSgt or TSgt Selectee.- Resident graduation is a prerequisite for MSgt
sew-on (Active Duty Only).
TSgt
MSgt
12.5 years
16 years
5 years
8 years
22 Years
24 YearsUSAF Senior NCO Academy (SNCOA)- Must be a SMSgt or SMSgt Selectee.- A percentage of top non-select (for promotion
to E-8) MSgts attend the SNCOA each year.- Resident or correspondence graduation is a
prerequisite for CMSgt sew-on.
SMSgt 19.2 years 11 years 26 Years
Upgrade To Superintendent (9-Skill Level)- Minimum rank of SMSgt.- Resident or correspondence graduate of
SNCOA.
CMSgt 21.5 years 14 years 30 Years
CFETP 2A6X6, October 2002
12
8.2. Base/Unit Education and Training Manager Checklist:
Table A8.2. Base/Unit Education and Training Manager ChecklistRequirements for Upgrade to: Y NJourneyman- Has the apprentice completed mandatory CDCs, if available?- Has the apprentice completed all appropriate 5-level core tasks identified in the CFETP?- Has the apprentice completed all other duty position tasks identified by the supervisor?- Has the apprentice completed 15 months training (9 months for retrainees) for award of the
5-skill level?- Has the apprentice met mandatory requirements listed in specialty description, AFMAN 36-2108
(Airman Classification), and CFETP?- Has the apprentice been recommended by their supervisor?Craftsman- Has the journeyman achieved the rank of SSgt?- Has the journeyman completed mandatory CDCs?- Has the journeyman completed all core tasks identified in the CFETP?- Has the journeyman completed all other duty position tasks identified by the supervisor?- Has the journeyman attended 7-skill level Craftsman Course?- Has the journeyman completed a minimum 12 months UGT for award of the 7-skill level?
TO: Squadron/CC
FROM: Squadron Training Manager
SUBJECT: Upgrade Trainee
Trainee is prepared to be upgraded and has completed all training requirements.
_______________________ _______________________ Training Manager Supervisor
CFETP 2A6X6, October 2002
13
SECTION C - SKILL LEVEL TRAINING REQUIREMENTS
9. Purpose. Skill level training requirements in this career field are defined in terms of tasks and knowledgerequirements. This section outlines the specialty qualification requirements for each skill level in general termsand establishes the mandatory requirements for entry, award, and retention of each skill level. The specifictasks and knowledge training requirements are identified in Part II, Section A, Specialty Training Standard(STS) and Section B of this CFETP.
10. Specialty Qualification Requirements. . The various skill levels in this career field are defined in termsof tasks and knowledge proficiency requirements for each skill level. They are stated in broad general terms andestablish the standards of performance. Unit work centers must develop a structured training program to ensurethe following requirements are met.
10.1. Apprentice Level Training.10.1.1. Specialty Qualification:10.1.1.1. Knowledge: Knowledge is mandatory of: electrical, electronic, and mechanical principles applying toaircraft E & E systems; concepts and application of maintenance directives; using and interpretation of wiringdiagrams, blueprints, and technical orders; and proper handling, use, and disposal of hazardous waste materials.Apprentices must be qualified to remove and install system components, perform operational checks, andtroubleshoot simple malfunctions using system schematics.10.1.1.2. Education: For entry into this specialty, completion of high school with courses in basic electronics,mathematics, general science and mechanics is desirable.10.1.1.3. Training: For award of AFSC 2A636, completion of a basic aircraft E&E systems maintenancecourse is mandatory.10.1.1.4. Experience: There is no experience necessary for entry into AFSC 2A636.10.1.1.5. Other: For entry into this specialty, normal color vision as defined in AFI 48-123 is mandatory.10.1.2. Training Sources. The initial skills course, J3ABR2A636 009, Aircraft Electrical and EnvironmentalSystems Apprentice will provide the required knowledge and qualifications. Initial skills training encompasseselectrical and environmental system theory and operation, electrical and electronic principles, systemcomponents, component removal and installation, introduction to maintenance concepts, general flight linemaintenance practices, use of technical publications, maintenance documentation, and support equipmentfamiliarization and use.10.1.3. Implementation. Upon graduation from Basic Military Training, airmen are assigned to the 82dTraining Wing for completion of Course J3ABR2A636 009, Aircraft Electrical and Environmental SystemsApprentice. Completion of this course will result in award of the 3-skill level.
10.2. Journeyman Level Training:10.2.1. Specialty Qualification:10.2.1.1. Knowledge: In addition to the 3-level qualifications, a 5-level must possess the knowledge and skillsnecessary to maintain electrical and environmental systems and associated subsystems. An individual must betask qualified on inspecting aircraft electrical and environmental systems and components, troubleshooting andcorrecting system malfunctions, and repairing and replacing system components. Journeymen performoperational checks, component repair, and use and maintenance of test and support equipment. Individuals canapply the proper handling, use, and disposal of hazardous waste and materials.10.2.1.2. Education: There are no formal education requirements for upgrade to 2A656.10.2.1.3. Training: Requirements for the Journeyman level require completion of the 5-level CDC andcompletion of the core tasks specified in the STS.
CFETP 2A6X6, October 2002
14
10.2.1.4. Experience. Qualification in and possession of AFS 2A636 and completion of all 5-level core taskson one MDS aircraft identified in the STS is mandatory.10.2.1.5. Other: Normal color vision as defined in AFI 48-123 is mandatory.10.2.2. Training Sources and Resources. The 5-level CDC provides the career knowledge training required.Qualification training and OJT will provide training and qualification on the core tasks identified in the STS, orAFJQS. The CDC is written to build from the trainee's current knowledge base, and provides more in-depthknowledge to support OJT requirements.10.2.3. Implementation. The units utilizing this STS, exportable courses, and CDCs perform training to the 5-level. Upgrade to the 5-level requires completion of the 2A655 CDC and 15 months upgrade training.
10.3. Craftsman Level Training:10.3.1. Specialty Qualification.10.3.1.1. Knowledge. In addition to the 5-level qualifications, an individual must possess advanced skills andknowledge of theory, concepts, principles and application of electrical and environmental systems. The 7-levelmust be able to supervise and train personnel to maintain electrical and environmental systems. They must beable to plan, schedule, and organize maintenance to ensure effective utilization of available resources.Qualification is required on advanced repair, inspection, troubleshooting, and diagnostic techniques. Historicaldocumentation analysis is also required for all 7-levels.10.3.1.2. Education. There are no additional education requirements beyond those defined for the apprenticelevel.10.3.1.3. Training. Completion of CDC 2A676, CDC 2AX7X, and the resident 7-level course, J3ACR2A676003, at Sheppard AFB TX is mandatory for upgrade to AFSC 2A676.10.3.1.4. Experience. Completion of all required 7-level core tasks as identified in the STS, and qualificationin and possession of AFSC 2A656. Also, experience performing or supervising functions such as installing,maintaining, or repairing aircraft E & E systems.10.3.1.5. Other. Normal color vision as defined in AFI 48-123 is mandatory.10.3.2. Training Sources and Resources. Seven-level upgrade training will be conducted by certified trainersusing AF core tasks, unit/MAJCOM specific courses, and the formal 7-level course, J3ACR2A676-000. The7-level CDC and resident courses are written to provide advanced system and management knowledge, andtroubleshooting skills.10.3.3. Implementation. The units utilizing the STS, and CDCs perform training to the 7-level. Upgrade tothe 7-level requires completion of CDC 2AX7X and CDC 2A675, completion of all core tasks, 12 monthsupgrade training, completion of the advanced (Craftsman) in-resident technical school, and promotion to E-5.
10.4. Superintendent Level Training (9-Level).10.4.1. Specialty Qualification.10.4.1.1. Knowledge. In addition to 7-level qualifications, an individual must possess advanced skills andknowledge of concepts and principles in the management of aircraft maintenance. The 9-level needs to be aneffective leader; must be able to forecast, budget and manage funds and other resources; and must beknowledgeable of all environmental standards and ensure adherence to the proper handling and disposal ofhazardous materials.10.4.1.2. Education. There are no additional requirements beyond those defined for the apprentice level.10.4.1.3. Training. For award of AFSC 2A690, completion of the Senior NCO Academy and promotion toSMSgt is mandatory10.4.1.4. Experience. Qualification in and possession of AFSC 2A676. Also, experience managing ordirecting repair activities for electrical and environmental systems and associated maintenance functions.10.4.1.5. Other. Normal color vision as defined in AFI 48-123 is mandatory.10.4.2. Training Sources and Resources. The Senior NCO Academy and unit OJT will be used for training.
CFETP 2A6X6, October 2002
15
10.4.3. Implementation. The 9-level will be awarded after completing MAJCOM requirements, unit OJT andpromotion to SMSgt. Individuals must attend the Senior NCO Academy in-residence or complete thecorrespondence course.
SECTION D - RESOURCE CONSTRAINTS
11. Purpose: This section of the CFETP identifies known resource constraints which precludeoptimum/desired training from being developed or conducted. Included is a narrative explanation of eachresource constraint, an impact statement describing the effect on training, the resources needed, and actionsrequired to satisfy the training requirements.
12. Apprentice Level Training.
12.1. Constraints. Two training requirements listed in Attachment 2 are constrained based on availability ofequipment at the 364 Training Squadron.
• A2.11.5 Use wire maintenance kit 2b/X• A2.9.3. Use interactive/electronic technical manuals 2b/X
12.2. Resources Required. Two wire maintenance kits are required to support training on item A2.11.5. Usewire maintenance kit. Fifteen laptop computer are required to support training on item A2.9.3. Useinteractive/electronic technical manuals.
13. Journeyman Level Training. No constraints noted.
14. Craftsman Level Training. No constaints noted.
PART II
SECTION A - SPECIALTY TRAINING STANDARD
1. Implementation. This STS will be used for technical training provided by Air Education and TrainingCommand (AETC) for classes beginning 03 Oct 2002.
2. Purpose. As prescribed in AFI 36-2201, this STS:
2.1. Lists in the column 1 (Task, Knowledge, and Technical Reference) the most common tasks, knowledge,and technical references (TR) necessary for airmen to perform duties in the 3-, 5-, and 7-skill level. An asterisk(*) before the number indicates a wartime course objective.
2.2. Identifies in column 2 (Core Tasks) by asterisk (*), specialty-wide training requirements for skill levelupgrade training. Core tasks identified with an *R are optional for the AFRC and the ANG. MAJCOMFunctional Managers, commanders, and supervisors may designate additional critical tasks as necessary. Whendesignated, certify these critical tasks using normal core task certification procedures. As a minimum,certification on all AFCFM directed core tasks applicable to the specialty must be completed for skill levelupgrade. Exemptions:
CFETP 2A6X6, October 2002
16
2.2.1. Core tasks which are not applicable to base assigned aircraft or equipment are not required for upgrade(units are not required to send personnel TDY for core task training)2.2.2. For units with more than one mission design (e.g. A-10) aircraft, upgrade trainees need only completecore tasks on a single mission design. MFMs, unit commanders, and/or supervisors may require trainees tocomplete core task training on additional mission design aircraft, if desired. If some of these core tasks involvetraining in another unit on base, trainees must still complete all core tasks relevant to at least one mission designaircraft. Flightline-assigned personnel must complete backshop core tasks and vice versa. All units are boundby the requirements in this CFETP and will accommodate core task trainees from other units.2.2.3. Units that use the GO81 maintenance data collection system do not need to complete Core AutomatedMaintenance System (CAMS) Computer Based Training (CBT) core tasks. However, these units must becapable of training CAMS related CBT core tasks for deployment preparation. This capability ensures GO81users are capable of operating CAMS prior to deploying to CAMS using units.
2.3. Provides certification for OJT. Column 3 is used to record completion of tasks and knowledge trainingrequirements. Use automated training management systems to document technician qualifications, if available.Task certification must show a certification completed date.
2.4. Shows formal training and correspondence course requirements. Column 4 shows the proficiency to bedemonstrated on the job by the graduate as result of training on the task/knowledge and the career knowledgeprovided by the correspondence course. When two codes are used in columns 4A and 4C(1) (e.g. 2b/b), the firstcode is the established requirement for resident training on the task/knowledge, and the second code indicatesthe level of training provided in the course due to equipment shortages or other resource constraints. SeeCADRE/AFSC/CDC listing maintained by the unit training manager for current CDC listing.
2.5. Qualitative Requirements. Attachment 1 contains the proficiency code key used to indicate the level oftraining and knowledge provided by resident training and career development courses.
2.6. Job Qualification Standard. Becomes a job qualification standard (JQS) for on-the-job training whenplaced in AF Form 623, On-The-Job Training Record, and used according to AFI 36-2201. For OJT, thetasks in column 1 are trained and qualified to the go/no go level. "Go" means the individual can perform the taskwithout assistance and meets local requirements for accuracy, timeliness, and correct procedures. When used asa JQS, the following requirements apply:2.6.1 Documentation. Document and certify completion of training IAW AFI 36-2201. Automated records,utilizing Core Automated Management System (CAMS) or Integrated Maintenance Data System (IMDS),reflecting this STS may be used and are highly encouraged. Use of attachments one, two and four aremandatory in individual training records along with CFETP Part I and Part II, Section A. Use of at least one ofattachments three, or five through fifteen is required. Identify duty position requirements by circling (in pencil)the subparagraph number next to the task statement. As a minimum, complete the following columns in Part 2of the CFETP: date training completed, trainee initials, trainer initials, and certifier initials (core tasks only).Trainers may sign off non-core and non-critical tasks by initialing the trainer's column; third party certificationis not required for non-core and non-critical tasks. There are no approved AFJQS for this AFSC.2.6.1.1. Converting from Old Document to CFETP. All AFJQSs and previous CFETPs are replaced by thisCFETP; therefore, conversion of all training records to this CFETP STS is mandatory. Use this CFETP STS (orautomated STS) to identify and certify all past and current qualifications.
CFETP 2A6X6, October 2002
17
2.6.1.1.1. For those core and critical tasks previously certified and required in the current duty position,evaluate current qualifications and when verified, recertify using current date as completion date, and entertrainee's and certifier's initials. Remember, during the transcription process no training is taking place.Therefore, the trainer's initials are not required.2.6.1.1.2. For non-core and non-critical tasks previously certified and required in the current duty position,evaluate current qualifications and when verified, recertify using current date as completion date, and entertrainee's and trainer's initials.2.6.1.1.3. When transcribing previous certification for tasks not required in the current duty position, carryforward only the previous completion date of certification (not the initials of another person). If and whentranscribed tasks become duty position requirements, recertify using standard certification procedures.2.6.1.1.4. The person whose initials appear in the trainer or certifier block during the transcription process mustmeet the requirements of their respective roles.2.6.1.1.5. Upon completion of the transcription process, give the old CFETP to the member.2.6.1.2. Documenting Career Knowledge. When a CDC is not available: the supervisor identifies CFETPPart II training references that the trainee requires for career knowledge and ensures, as a minimum, that traineescover the mandatory items in AFI 36-2108. For two-time CDC course exam failures: Supervisors identify allPart II items corresponding to the areas covered by the CDC. The trainee completes a study of references,undergoes evaluation by the task certifier, and receives certification on the CFETP Part II. Supervisors mustdocument successful completion of career knowledge prior to submission of a CDC waiver.2.6.1.3. Decertification and Recertification. When an airman is found to be unqualified on a task previouslycertified for his or her position, the supervisor lines through the previous certification or deletes previouscertification when using automated system. Appropriate remarks are entered on the AF Form 623A, On-The-Job Training Record Continuation Sheet, as to the reason for decertification. The individual is recertified (ifrequired) either by erasing the old entries and writing in the new or by using correction fluid/tape (if the entrieswere made in ink) over the previously certified entry.2.6.2. AF Form 797. When additional items not listed in the CFETP Part II are necessary in the current dutyassignment, enter them on the 797. Fill out the form IAW AFI 36-2201.2.6.3. Disposition of Training Records. Upon separation, retirement, commissioning, or promotion to MasterSergeant (unless otherwise directed by the AFCFM, MAJCOM, unit commander, or supervisor), give theindividual their training records. Also, give individuals outdated training records after transcribing records. Donot remove any training records that show past qualifications unless transcribed to a new CFETP/AFJQS. Forexample, an individual working in a tool crib must maintain documented career field qualifications in case theyreturn to duty on the flightline or in the shop. Supervisors must exercise good judgment when removingtraining records not needed in current duty positions.
2.7. Specialty Training Standard. Is a guide for development of promotion tests used in the WeightedAirman Promotion System (WAPS). Senior NCOs with extensive practical experience in their career fieldsdevelops Specialty Knowledge Tests (SKTs) at the USAF Occupational Measurement Squadron. The testssample knowledge of STS subject matter areas judged by test development team members as most appropriatefor promotion to higher grades. Questions are based upon study references listed in the WAPS catalog.Individual responsibilities are in chapter 4 of AFI 36-2502, Airman Promotion Program. WAPS is notapplicable to the Air National Guard or Air Force Reserve.
CFETP 2A6X6, October 2002
18
3. Recommendations. Report unsatisfactory performance of individual course graduates to the AETCTraining Manager at 364 TRS/TRR, 511 9th Ave. Suite 1, Sheppard AFB TX, 76311-2338, DSN 736-2772.Reference specific STS paragraphs. For a quick response to problems, call our customer service informationline, DSN 736-2574.
BY ORDER OF THE SECRETARY OF THE AIR FORCE
OFFICIAL MICHAEL E. ZETTLER, Lieutenant General, USAFDCS/Installations and Logistics
15 ATTACHMENTS1. Proficiency Code Key (Mandatory)2. Training Requirements, Fundamentals (Mandatory)3. Training Requirements, Generic (Mandatory, except as indicated in note 1)4. Training Requirements, CDC 2AX7X (Mandatory)5. Training Requirements, B-2 (Optional)6. Training Requirements, C-5 (Optional)7. Training Requirements, C-9 (Optional)8. Training Requirements, C-17 (Optional)9. Training Requirements, C-130 (Optional)10. Training Requirements, C-141 (Optional)11. Training Requirements, F-15 (Optional)12. Training Requirements, F-16 (Optional)13. Training Requirements, KC-10 (Optional)14. Training Requirements, KC-135 (Optional)15. Training Requirements, MH-53J (Optional)
FUNDAMENTAL TRAINING REQUIREMENTSSTS 2A6X6, October 2002
19Attachment 2
This Block Is For Identification Purposes OnlyName Of TraineePrinted Name (Last, First, Middle Initial) Initials (Written) SSAN
Printed Name Of Training/Certifying Official And Written InitialsN/I N/I
N/I N/I
N/I N/I
N/I N/I
N/I N/I
N/I N/I
N/I N/I
N/I N/I
QUALITATIVE REQUIREMENTS
Proficiency Code KeyScaleValue
Definition: The individual
1 IS EXTREMELY LIMITED (Can do simple parts of the task. Needs to be told or shown how to do mostof the task.)
Task 2 IS PARTIALLY PROFICIENT (Can do most parts of the task. Needs only help on hardest parts.)
Performance 3 IS COMPETENT (Can do all parts of the task. Needs only a spot check of completed work.)
Levels 4 IS HIGHLY PROFICIENT (Can do the complete task quickly and accurately. Can tell or show othershow to do the task.)
a KNOWS NOMENCLATURE (Can name parts, tools, and simple facts about the task. )
*Task b KNOWS PROCEDURES (Can determine step by step procedures for doing the task. )
Knowledge c KNOWS OPERATING PRINCIPLES (Can identify why and when the task must be done and why eachstep is needed.)
Levels d KNOWS ADVANCED THEORY (Can predict, isolate, and resolve problems about the task.)
A KNOWS FACTS (Can identify basic facts and terms about the subject.)
**Subject B KNOWS PRINCIPLES (Can identify relationship of basic facts and state general principles about thesubject.)
Knowledge C KNOWS ANALYSIS (Can analyze facts and principles and draw conclusions about the subject.)
Levels D KNOWS EVALUATION (Can evaluate conditions and make proper decisions about the subject.)
Explanations* A task knowledge scale value may be used alone or with a task performance scale value to define a level of knowledge for a specific task. (Example: b and 1b)
** A subject knowledge scale value is used alone to define a level of knowledge for a subject not directly related to any specific task, or for a subject common toseveral tasks.
- This mark is used alone instead of a scale value to show that no proficiency training is provided in the courses or CDC’s.
/ This mark is used in course columns to show that training is required but not given due to limitations in resources (3c/b, 2b/b etc.).
Note: Tasks and knowledge items shown with an asterisk (*) in column one are trained during war time.
FUNDAMENTAL TRAINING REQUIREMENTSSTS 2A6X6, October 2002
20Attachment 2
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
ATTACHMENT 2
NOTE 1: The tasks and knowledge listed in attachment 2 will be performed by all personnel in the Aircraft Electrical and Environmental System Specialty.
NOTE 2: Tasks and knowledge identified by an asterisk (*) in column 1 are trained in the resident wartime course.
NOTE 3: Users are responsible for annotating training references to identify current references pending STS revision.
NOTE 4: Items marked in columns 2a or 2b marked with a (*R) are optional core tasks for ANG and AFRC.
NOTE 5: Address comments and recommended changes through the MAJCOM Functional Managers to the AETC Training Manager, DSN 736-2772.
A2.1. SECURITY
A2.1.1. Communication Security (COMSEC)
TR: DOD 52001-R; AFP100-46
- - - -
A2.1.1.1. Information Security - - - -
*A2.1.2. Operations Security (OPSEC) specific vulnerabilities of AFSC 2A6X6
TR: 55-30
A - - -
A2.2. AF OCCUPATIONAL SAFETY AND HEALTH (AFOSH) PROGRAM
TR: AFIs 91-202, 91-302; Applicable OSHA and AFOSH standards
*A2.2.1. Hazards of AFSC 2A6X6 A B C -
*A2.2.2. AFOSH standards for AFSC 2A6X6 A B - -
A2.2.3. Use safety precautions
TR: AFI 21-101; AFOSH 91-66; TOs 00-25-234, 1-1A-14, 1-1A-15, 8D series, 11A series, 31-1-2, 32-1-101, 33C3; 15X-1-1series
*A2.2.3.1. With handtools 2b B - -
*A2.2.3.2. In shop 2b B - -
*A2.2.3.3. On flight line 2b B - -
A2.2.4. Nuclear safety/nuclear safety regulations
TR: AFRs 35-99,122-1, 122-4, 122-5
- A - -
*A2.2.5. Portable fire extinguishers
TR: AFOSH 91-56
A - - -
*A2.2.6. Initial Federal Hazard Communication Training Program (FHCTP)
TR: AFOSH TOs 48-21, 91-56, 91-66
A - - -
*A2.2.7. Explosive Safety Program
TR: AFMAN 91-201
A B - -
A2.3. HAZARDOUS MATERIALS AND WASTE HANDLING ACCORDING TO ENVIRONMENTAL STANDARDS
TR: AFI 23-504, EPA State Regulations
*A2.3.1. Types of hazardous material /fluids B B - -
*A2.3.2. Handling procedures B B - -
FUNDAMENTAL TRAINING REQUIREMENTSSTS 2A6X6, October 2002
21Attachment 2
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
*A2.3.3. Storage and labeling B B - -
*A2.3.4. Proper disposal B B - -
A2.4. MAINTENANCE MANAGEMENT
A2.4.1. Logistics/OPS Group Organizational Structure
TR: AFI 21-101, MAJCOM Instructions
- B - -
A2.4.2. Basic functions within the maintenance complex
TR: AFI 21-101, MAJCOM Instructions
- B - -
A2.4.3. Funds Management/depot level reparable (DLR)
TR: AFM 23-110, AFI23-111
- - C -
A2.4.4. Status reporting
TR: AFI21-103
- A - -
A2.4.5. Mission Essential System List (MESL)
TR: AFI21-103
- - B -
A2.5. MAINTENANCE AND INSPECTION
*A2.5.1. Maintenance systems
TR: AFI 21-101 TO 00 Series
B B - -
*A2.5.2. Inspection systems
TR: TOs 00-20 series, 8-1-1, 1-1A-14
B B - -
A2.5.2.1. Perform acceptance/transfer inspection on aircraft - - - -
A2.5.2.2. Perform isochronal/phase inspections (A,B,C checks)
- - - -
A2.5.2.3. Perform other scheduled maintenance inspections (e.g. HSC, refurb, etc.)
- - - -
*A2.5.3. Process deficiency reports
TR: TO 00-35D-54
* A B - -
A2.5.4. AFTO 781 series forms
TR: TOs 00-20 series
- - -
*A2.5.5. Use AFTO Form 781A
TR: TOs 00-20 series
* 2b B - -
*A2.5.6. Use AFTO Form 781H
TR: TOs 00-20 series
* B B - -
*A2.5.7. Use AFTO Form 781K
TR: TOs 00-20 series
* 2b B - -
A2.5.8. General Aircraft Procedures
TR: MAJCOM instructions, applicable aircraft TO/checklist
A2.5.8.1. Statically ground aircraft - - - -
A2.5.8.2. Open and close engine cowling - - - -
A2.5.8.3. Remove and install aircraft maintenance panels - - - -
FUNDAMENTAL TRAINING REQUIREMENTSSTS 2A6X6, October 2002
22Attachment 2
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A2.5.8.4. Use aircraft interphone system - - - -
A2.5.8.5. Perform aircraft egress - - - -
A2.5.8.6. Inspect/use ground maintenance stands - - - -
A2.5.8.7. Select/use restraint harness(e.g. Fall protection/prevention equipment)
- - - -
A2.5.8.8. Operate aircraft radios - - - -
A2.5.8.9 Jack Team member - - - -
A2.5.8.10 Marshall aircraft - - - -
A2.5.8.11 Tow Team member - - - -
A2.5.8.12 Refuel/defuel member - - - -
A2.6. USE AUTOMATED MAINTENANCE SYSTEM
A2.6.1. GO81
TR: AFM 66-267,66-278, TO 00-20
A2.6.1.1. Use GO81 - - - -
A2.6.1.2. 9050 - Open aircraft discrepancies - - - -
A2.6.1.3. 9010 - Close aircraft discrepancies - - - -
A2.6.1.4. 9099 - MDC/close aircraft discrepancies * - - - -
A2.6.1.5. 8063 - Jobs closed, no MDC taken - - - -
A2.6.1.6. 9032 - Generate aircraft flying forms - - - -
A2.6.1.7. 9128 - Build repairable item processing tag(AFTO Form 350)
- - - -
A2.6.1.8. 8044 - Supply information on a particular aircraft - - - -
A2.6.1.9. 8057 - Tail number bin (TNB) list - - - -
*A2.6.2. Use CAMS
TR: AFCSM 21-556
* 2b B - -
A2.6.2.1. Complete CBT course number J6ANU00066-043,CAMS for Flightline and Backshop
* - - - -
A2.7. SUPERVISION
A2.7.1. Orient new personnel
TR: AFIs 36-2108, 36-2202
- - - -
A2.7.2. Assign personnel to work crews
TR: AFI 21-101
- - C -
A2.7.3. Plan work assignments and priorities
TR: AFI 21-101
- - C -
A2.7.4. Schedule work assignments
TR: AFI 21-101
- - C -
A2.7.5. Establish
TR: AFI 21-101, 00-20 Series TOs
A2.7.5.1. Work methods - - C -
FUNDAMENTAL TRAINING REQUIREMENTSSTS 2A6X6, October 2002
23Attachment 2
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A2.7.5.2. Controls - - C -
A2.7.5.3. Performance standards - - C -
A2.7.5.4. Personal accountability - - C -
A2.7.6. Evaluate work performance of subordinate personnel
TR: Applicable aircraft/shop TOs
- - C -
A2.7.7. Resolve technical problems for subordinate personnel
TR: Applicable aircraft/shop TOs
- - - -
A2.7.8. Counsel personnel and resolve individual problems - - - -
A2.7.9. Initiate action to correct substandard performance by personnel
TR: AFIs 36-2503, 36-2907
- - - -
A2.8. TRAINING
TR: AFI 36-2201
A2.8.1. Career Field Education and Training Plan (CFETP)
A2.8.1.1. Maintain CFETP - - B -
A2.8.1.2. Interpret CFETP - - B -
A2.8.2. Management of training
TR: AFI 21-101, AFI 36-2201
- B - -
A2.8.3. Evaluate personnel to determine need for training - - - -
A2.8.4. Plan and supervise OJT
A2.8.4.1. Conduct training - - - -
A2.8.4.2. Counsel trainees on their progress - - - -
A2.8.4.3. Monitor effectiveness of training - - - -
A2.8.5. Evaluate effectiveness of training programs/trainingevaluation reports
- - - -
A2.8.6. OJT trainer requirements
A2.8.6.1. Prepare teaching outlines or tasks breakdowns - - - -
A2.8.6.2. Provide trainees theory and training on actual equipment
- - - -
A2.8.6.3. Provide feedback on training provided - - - -
A2.8.7. OJT task certifier requirements
A2.8.7.1. Provide supervisor and trainer feedback on results of training provided and trainee’s strengths/weaknesses
- - - -
A2.9. TECHNICAL PUBLICATIONS
*A2.9.1. Fundamentals of the technical order system
TR: TO 00-5 series
B B - -
*A2.9.2. Use technical manuals for specific equipment
TR: TO 00-5-1 (sec II and V)
* 2b B - -
FUNDAMENTAL TRAINING REQUIREMENTSSTS 2A6X6, October 2002
24Attachment 2
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
*A2.9.3. Use interactive/electronic technical manuals 2b/X A - -
*A2.9.4. Use abbreviated technical orders
TR: TO 00-5-1 (sec II)
* 2b B - -
*A2.9.5. Use methods and procedures technical orders
TR: TO 00-XX series
2b B - -
A2.9.6. Use standard publications
TR: AFI, AFMAN, AFPAM series
- B - -
*A2.9.7. Technical order improvement report
TR: TO 00-5-1 (sec VIII)
A B 2b -
*A2.9.8. Time compliance technical order
TR: TO 00-5-15
A B - -
A2.9.9. Maintain technical publications - - - -
A2.10. AF SUPPLY DISCIPLINE
TR: AFMAN 23-110, AFI 23-111, 21-101
A2.10.1. Research parts
TR: TO 00-20 series
- - - -
*A2.10.2. Property accountability A B C -
A2.10.3. Principles of supply - B - -
*A2.10.4. Issue and turn-in procedures A B - -
*A2.10.5 Use of issue and turn-in forms 2b B - -
*A2.10.6. Use Standard Base Supply System (SBSS)
TR: AFM 23-110
2b B - -
A2.10.7. Supply reports - - B -
A2.10.8. Utilize equipment allowance standards - - - -
A2.11. ELECTRICAL AND ENVIRONMENTALFUNDAMENTALS
TR: AFI 21-101; AFOSH 91-66; TOs 00-25-234,1-1A-8, 1-1A-14, 32-1-101
*A2.11.1. Composite toolkit (CTK) program A B - -
*A2.11.2. Use handtools 2b B - -
A3.11.3. Use duct reflanging/reforming tool - - - -
A2.11.4. Solder electrical connections
*A2.11.4.1. Conventional devices * 2b B - -
A2.11.4.2. Solid state devices - B - -
A2.11.4.3. Advanced soldering - - - B
*A2.11.5 Use wire maintenance kit 2b/X - - -
A2.11.6. Use solderless electrical connector devices
*A2.11.6.1. Connector plugs * 2b B - -
*A2.11.6.2. Splices * 2b B - -
FUNDAMENTAL TRAINING REQUIREMENTSSTS 2A6X6, October 2002
25Attachment 2
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
*A2.11.6.3. Terminals * 2b B - -
A2.11.6.4. Wire bundle
*A2.11.6.4.1. Remove 2b - - -
*A2.11.6.4.2. Repair 2b - - -
*A2.11.6.4.3. Install 2b - - -
A2.11.6.4.4. Modular blocks - - - -
*A2.11.7. Corrosion control A B - -
*A2.11.8. Use safetying devices * 2b B - -
A2.11.9. Use safety cables - - - -
*A2.11.10. Use appropriate hardware * 2b B - -
*A2.11.11. Special wiring: special purpose wire, compact wire bundle, electrical magnetic pulse (EMP) hardened cable
A B - -
A2.11.12. Engine wiring harness
A2.11.12.1. Inspect - - - -
A2.11.12.2. Repair - - - -
A2.11.13. Benchcheck - - - -
A2.11.14. Protect exposed electrical connectors, open pressure lines, and ducting
- - - -
A2.11.15. Remove
A2.11.15.1. Switches/protective devices - - - -
A2.11.15.2. Relay/socket - - - -
A2.11.15.3. Proximity sensors/switch - - - -
A2.11.15.4. Transformer/power supply - - - -
A2.11.15.5. Circuit cards - - - -
A2.11.15.6. Integration matrix box - - - -
A2.11.16. Install
A2.11.16.1. Switches/protective devices - - - -
A2.11.16.2. Relay/socket - - - -
A2.11.16.3. Proximity sensors/switch - - - -
A2.11.16.4. Transformer/power supply - - - -
A2.11.16.5 Circuit cards - - - -
A2.11.16.6. Integration matrix box - - - -
A2.11.17. Fabricate flexible conduits/wiring harness - - - -
A2.12. AIRCRAFT FAMILIARIZATION
TR: Applicable aircraft TOs
*A2.12.1. Principles of flight B - - -
*A2.12.2. Location of structural components A - - -
*A2.12.3. Location of system components A - - -
FUNDAMENTAL TRAINING REQUIREMENTSSTS 2A6X6, October 2002
26Attachment 2
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
*A2.12.4. Glass cockpit A - - -
A2.12.5. Operate malfunction display/mission computer display
- - - -
A2.12.6. Smoke and fire detection/suppression procedures - - - -
A2.12.7. Operate mission computer - - - -
A2.12.8. Operate maintenance monitor/interface (built-in test) panel
- - - -
*A2.12.9. Databus Channels/Principles A B - -
A2.13. ELECTRICAL/ELECTRONIC FUNDAMENTALS
TR: TO 00-25-234; 31-1-141 series; applicable aircraft TOs
*A2.13.1. DC fundamentals: Electron theory, magnetism, voltage generation, Kirchhoff’s law, Ohm’s law, resistance and power formulas, DC motors, control protective devices
B B - -
*A2.13.2. AC fundamentals: Inductors, capacitors, voltage generation, transformers, AC motors
B B - -
*A2.13.3. Electronic fundamentals: Solid state devices, power supplies, amplifiers circuits, electronic voltage regulators, logic gates
B B - -
*A2.13.4. Use wiring diagrams * 2b B - -
*A2.13.5. Use schematics * 2b B - -
*A2.13.6. Use troubleshooting techniques 1b B - C
*A2.13.7. Electrostatic discharge (ESD) A B - -
A2.14. ELEMENTS OF PHYSICS
TR: ???
*A2.14.1. Temperature B B - -
*A2.14.2. Pressure B B - -
*A2.14.3. Atmosphere B B - -
*A2.14.4. Air flow B B - -
A2.15. BATTERY SHOP
TR: AFOSH 91-66, TOs 8D2-2 series, 8D2-3 series,33C3 series
A2.15.1. Nickel-Cadmium
*A2.15.1.1. Battery fundamentals B B - -
A2.15.1.2. Operate charging equipment * - - - -
A2.15.1.3. Maintain charging equipment - - - -
A2.15.1.4. Service batteries * - B - -
A2.15.2. Lead acid
TR: TOs 8D2-1-31, 33A1 series
*A2.15.2.1. Battery fundamentals B B - -
A2.15.2.2. Operate charging equipment * - - - -
FUNDAMENTAL TRAINING REQUIREMENTSSTS 2A6X6, October 2002
27Attachment 2
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A2.15.2.3. Maintain charging equipment - - - -
A2.15.2.4. Service batteries * - B - -
A2.16. CRYOTAINER SYSTEM
TR: AFOSH standards; TOs 34Y5 series, 35D3 series, 35D29 series, 36G2 series, 37C2 series, 37C11-3-1, 15X-1-1
A2.16.1. Operational fundamentals
*A2.16.1.1. Oxygen B B - -
*A2.16.1.2. Nitrogen B B - -
A2.16.2. Oxygen cryotainer/cart
A2.16.2.1. Operational check *R - - - -
A2.16.2.2. Troubleshoot - B - -
A2.16.2.3. Drain - B - -
A2.16.2.4. Purge - B - -
A2.16.2.5. Evacuate - B - -
A2.16.2.6. Repair components - - - -
A2.16.2.7. Remove components *R - - - -
A2.16.2.8. Install components *R - - - -
A2.16.2.9. Leak check *R - B - -
A2.16.2.10. Inspect *R - B - -
A2.16.2.11. Clean components - B - -
A2.16.3. Nitrogen cryotainer/cart
A2.16.3.1. Operational check - - - -
A2.16.3.2. Troubleshoot - - - -
A2.16.3.3. Drain - - - -
A2.16.3.4. Purge - - - -
A2.16.3.5. Evacuate - - - -
A2.16.3.6. Repair components - - - -
A2.16.3.7. Remove components - - - -
A2.16.3.8. Install components - - - -
A2.16.3.9. Leak check - - - -
A2.16.3.10. Inspect - - - -
A2.16.4. LN2 GSU Truck
A2.16.4.1. Operational check - - - -
A2.16.4.2. Troubleshoot - - - -
A2.16.4.3. Drain - - - -
A2.16.4.4. Purge - - - -
A2.16.4.5. Evacuate - - - -
FUNDAMENTAL TRAINING REQUIREMENTSSTS 2A6X6, October 2002
28Attachment 2
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A2.16.4.6. Repair components - - - -
A2.16.4.7. Remove components - - - -
A2.16.4.8. Install components - - - -
A2.16.4.9. Leak check - - - -
A2.16.4.10. Inspect - - - -
A2.16.5. Gaseous nitrogen/ oxygen servicing carts
A2.16.5.1. Troubleshoot - - - -
A2.16.5.2. Inspect - - - -
A2.16.5.3. Remove components - - - -
A2.16.5.6 Install components - - - -
A2.16.5.7. Leak check - - - -
A2.16.5.8. Clean components - - - -
A2.16.6. Purge unit GSU 62/M
A2.16.6.1. Troubleshoot - - - -
A2.16.6.2. Inspect - - - -
A2.16.6.3. Remove components - - - -
A2.16.6.4. Install components - - - -
A2.17. METERS AND TESTERS
TR:: Applicable 33 series TOs
A2.17.1. Use insulation tester - B - -
A2.17.2. Use decade box - B - -
*A2.17.3. Use ECS tester 2b - - -
A2.17.4. Use electrical/pneumatic component testers - - - -
*A2.17.5. Use oxygen system regulator tester 2b B - -
*A2.17.6. Use sonic leak detector 2b B - -
A2.17.7. Use cockpit cabin pressure leakage tester - B - -
*A2.17.8. Use anti-skid tester 2b B - -
*A2.17.9. Use bonding meter A B - -
A2.17.10. Load Bank
A2.17.10.1. Use - B - -
A2.17.10.2. Troubleshoot - - - -
A2.17.10.3. Repair - - - -
*A2.17.11. Use multimeter * 2b B - -
*A2.17.12. Use igniter circuit tester a B - -
A2.17.13. Use oscilloscope - - - B
*A2.17.14. Use time domain reflectometer A B 2b -
A2.17.15. Perform periodic/inspections/pre-use inspections - - - -
A2.17.16. Maintenance/repair on test equipment - - - -
FUNDAMENTAL TRAINING REQUIREMENTSSTS 2A6X6, October 2002
29Attachment 2
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A2.17.17. Locally manufactured test equipment
A2.17.17.1. Use - - - -
A2.17.17.2. Troubleshoot - - - -
A2.17.17.3. Repair - - - -
A2.17.18. Bench check/repair air conditioning temperature control box tester
- - - -
A2.17.19. Use linear and rotary actuator test stand - - - -
A2.17.20. Troubleshoot/repair linear and rotary actuator teststand
- - - -
A2.17.21. Use flap/slat brake tester - - - -
A2.17.22. Constant speed drive/generator test stand
A2.17.22.1. Use - B - -
A2.17.22.2. Troubleshoot - - - -
A2.17.22.3. Repair - - - -
A2.17.23. Use frequency meters/counters - - - -
A2.17.24. Use fire system tester - - - -
A2.17.25. Use fire detection control unit tester - - - -
A2.17.26. Empenage de-ice controller tester
A2.17.26.1. Use - - - -
A2.17.26.2. Troubleshoot - - - -
A2.17.26.3. Repair - - - -
A2.17.27. K735 test set components
A2.17.27.1. Use - - - -
A2.17.27.2. Troubleshoot - - - -
A2.17.27.3. Repair - - - -
A2.17.28. Use TTU-205 - - - -
A2.17.29. Use micron gauge - - - -
A2.17.30. Use ultraviolet light - - - -
*A2.17.31. Operate wiring marking machines 2b - - -
A2.17.32. Use pneumatic system tester (electrical/nitrogen) - - - -
A2.17.33. Use windshield anti-ice system tester - - - -
A2.17.34. Use Jet-Cal tester - - - -
A2.17.35. Use Temp- Cal tester - - - -
A2.17.36. Use vacuum pump - - - -
A2.17.37 Use landing gear control panel tester- - - - -
A2.17.38 Use throttle quadrant tester - - - -
A2.18. Inspect/Repair Explosion Proof lights - - - -
FUNDAMENTAL TRAINING REQUIREMENTSSTS 2A6X6, October 2002
30Attachment 2
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A2.19. LIFE RAFT INFLATION EQUIPMENT
TR: AFOSH standards; TO 14S1 series, 8 series component TOs
A2.19.1. Operational fundamentals
A2.19.2. Life raft inflation equipment - B - -
A2.19.3. Slide inflation equipment - - - -
A2.19.4. Service Bottles - B - -
A2.19.5. Inspect System Components
A2.19.5.1.. Life raft inflation cylinder recharging equipment - - - -
A2.19.6. Repair
A2.19.6.1. Bottles - - - -
A2.19.6.2. Life raft inflation cylinder recharging equipment - - - -
A2.19.7. Service/leak check slide/raft bottles - - - -
GENERIC TRAINING REQUIREMENTSSTS 2A6X6, October 2002
31Attachment 3
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
ATTACHMENT 3
NOTE 1: In addition to attachment 2, the tasks and knowledge in attachment 3 will be performed by personnel assigned to maintain aircraft not listed in specificCFETP Attachments.
NOTE 2: Tasks and knowledge identified by an asterisk (*) in column 1 are trained in the resident wartime course.
NOTE 3: Users are responsible for annotating training references to identify current references pending STS revision.
NOTE 4: Items marked in columns 2a or 2b marked with a (*R) are optional core tasks for ANG and AFRC.
NOTE 5: Address comments and recommended changes through the MAJCOM Functional Managers to the AETC Training Manager, DSN 736-2772.
A3.1. AC POWER SYSTEM
TR: Applicable aircraft TOs, 8 series component TOs
*A3.1.1. Operational fundamentals B B - -
A3.1.2. Operational check
A3.1.2.1. 60 Hertz system - - - -
A3.1.2.2. Co-pilot instrument power system - - - -
A3.1.2.3. BPCU interrogation/bite check - - - -
A3.1.2.4. Main generator System
*A3.1.2.5. Single generator 2b - - -
A3.1.2.6. Multi-generator - - - -
*A3.1.2.7. Emergency generator System 2b - - -
A3.1.3. Troubleshoot
A3.1.3.1. 60 Hertz system - - - -
A3.1.3.2. Co-pilot instrument power system - - - -
A3.1.3.3. BPCU interrogation/bite check - - - -
A3.1.3.4 Main generator System
*A3.1.3.5 Single generator 2b B - -
A3.1.3.6 Multi-generator - B - C
*A3.1.3.7 Emergency generator System 2b B - C
A3.1.4. Inspect system components * - - - -
A3.1.5. Remove components
A3.1.5.1. AC generator control units - - - -
A3.1.5.2. CSD - - - -
A3.1.5.3. AC generators - - - -
A3.1.5.4. Generator/bus protection panels - - - -
A3.1.5.5. Generator voltage regulators - - - -
A3.1.5.6. Generator frequency load controllers - - - -
A3.1.5.7. Frequency control unit - - - -
A3.1.5.8. Bus tie/generator line contactor - - - -
A3.1.5.9. Inverter - - - -
A3.1.5.10. Circuit breaker panels - - - -
GENERIC TRAINING REQUIREMENTSSTS 2A6X6, October 2002
32Attachment 3
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A3.1.5.11. Relays - - - -
A3.1.5.12. Survivability/vulnerability (S/V) box - - - -
A3.1.5.13. CSD/IDG Filters - - - -
A3.1.5.14. Current transformer - - - -
A3.1.6. Repair components
A3.1.6.1. AC generator control units - - - -
A3.1.6.2. CSD - - - -
A3.1.6.3 AC generators - - - -
A3.1.6.4. Generator/bus protection panels - - - -
A3.1.6.5. Generator voltage regulators - - - -
A3.1.6.6. Generator frequency load controllers - - - -
A3.1.6.7. Frequency control unit - - -
A3.1.6.8. Bus tie/generator line contactor - - - -
A3.1.6.9. Inverter - - - -
A3.1.6.10. Circuit breaker panels - - - -
A3.1.7. Install components
A3.1.7.1. AC generator control units - - - -
A3.1.7.2. CSD - - - -
A3.1.7.3. AC generators - - - -
A3.1.7.4. Generator/bus protection panels - - - -
A3.1.7.5. Generator voltage regulators - - - -
A3.1.7.6. Generator frequency load controllers - - - -
A3.1.7.7 Frequency control unit - - - -
A3.1.7.8. Bus tie/generator line contactor - - - -
A3.1.7.9. Relays - - - -
A3.1.7.10.. Survivability/vulnerability (S/V) box - - - -
A3.1.7.11. CSD/IDG Filters - - - -
A3.1.7.12. Current transformer - - - -
A3.1.7. 13. Inverter - - - -
A3.1.7. 14. Circuit breaker panels - - - -A3.1.8. Bench check
A3.1.8.1. AC generator control units - - - -
A3.1.8.2. CSD - - - -
A3.1.8.3. AC generators - - - -
A3.1.8.4. Generator/bus protection panels - - - -
A3.1.8.5. Generator voltage regulators - - - -
A3.1.8.6. Generator frequency load controllers - - - -
A3.1.8.7. Frequency control unit - - - -
GENERIC TRAINING REQUIREMENTSSTS 2A6X6, October 2002
33Attachment 3
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A3.1.8.8. Bus tie/generator line contactor - - - -
A3.1.8.9. Relays - - - -
A3.1.8.10. Inverter - - - -
A3.1.8.11. Circuit breaker panels - - - -
A3.2. DC POWER SYSTEM
TR: Applicable aircraft TOs, 8 series component TOs
*A3.2.1. Operational fundamentals B B - -
*A3.2.2. Operational check * 2b - - -
*A3.2.3. Troubleshoot 2b B - C
A3.2.4. Inspect system components * - - - -
A3.2.5. Remove components
A3.2.5.1. Battery - - - -
A3.2.5.2. Battery charger - - - -
A3.2.5.3. Transformer rectifier - - - -
A3.2.5.4. Reverse current relays - - - -
A3.2.5.5. Circuit breaker panels - - - -
A3.2.6. Repair components
A3.2.6.1. Battery charger - - - -
A3.2.6.2. Transformer rectifier - - - -
A3.2.6.3. Reverse current relays - - - -
A3.2.6.4. Circuit breaker panels - - - -
A3.2.7. Install components
A3.27.1. Battery - - - -
A3.2.7.2 Battery charger - - - -
A3.2.7.3 Transformer rectifier - - - -
A3.2.7.4. Reverse current relays - - - -
A3.2.7.5. Circuit breaker panels - - - -
A3.2.8. Bench check components
A3.2.8.1. Battery charger - - - -
A3.2.8.2. Transformer rectifier - - - -
A3.2.8.3. Reverse current relays - - - -
A3.2.8.4. Circuit breaker panels - - - -
A3.3. EXTERNAL POWER SYSTEM
TR: Applicable aircraft TOs, 8 series component TOs
*A3.3.1. Operational fundamentals B B - -
*A3.3.2. Operational check * 2b - - -
*A3.3.3. Troubleshoot 2b B - B
A3.3.4. Inspect system components * - - - -
GENERIC TRAINING REQUIREMENTSSTS 2A6X6, October 2002
34Attachment 3
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A3.3.5. Remove components
A3.3.5.1. External power receptacle - - - -
A3.3.5.2. External power monitor - - - -
A3.3.5.3. Line contactor - - - -
A3.3.6. Install components
A3.3.6.1. External power receptacle - - - -
A3.3.6.2. External power monitor - - - -
A3.3.6.3. Line contactor - - - -
A3.3.7. APU power system
A3.3.7.1. Operational check * - - - -
A3.3.7.2. Troubleshoot - - - -
A3.3.7.3. Inspect system components * - - - -
A3.3.7.4. Remove components
A3.3.7.4.1. Generator - - - -
A3.3.7.4.2. Generator control unit - - - -
A3.3.7.4.3. Line contactor - - - -
A3.3.7.4.4. Electronic control unit - - - -
A3.3.7.5. Repair components
A3.3.7.5.1. Generator - - - -
A3.3.7.5.2. Generator control unit - - - -
A3.3.7.6. Install components
A3.3.7.6.1. Generator - - - -
A3.3.7.6.2. Generator control unit - - - -
A3.3.7.6.3. Line contactor - - - -
A3.3.7.6.4. Electronic control unit - - - -
A3.4. LIGHTING SYSTEM
TR: Applicable aircraft TOs, 8 series component TOs
A3.4.1. Operational fundamentals
*A3.4.1.1. Interior B B - -
*A3.4.1.2. Exterior B B - -
*A3.4.1.3. Emergency B B - -
A3.4.1.4. UARRSI/AR receptacle - - - -
A3.4.2. Operational check
*A3.4.2.1. Interior * 2b - - -
*A3.4.2.2. Exterior * 2b - - -
*A3.4.2.3. Emergency * 2b - - -
A3.4.2.4. UARRSI/AR receptacle * - - - -
A3.4.3. Troubleshoot
GENERIC TRAINING REQUIREMENTSSTS 2A6X6, October 2002
35Attachment 3
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
*A3.4.3.1. Interior 2b - - -
*A3.4.3.2. Exterior 2b - - -
*A3.4.3.3. Emergency 2b - - -
A3.4.3.4. UARRSI/AR receptacle - - - -
A3.4.4. Inspect
A3.4.4.1. Interior * - - - -
A3.4.4.2. Exterior * - - C -
A3.4.4.3. Emergency * - - - -
A3.4.4.4. UARRSI/AR receptacle * - - - -
A3.4.5. Remove components
A3.4.5.1. Interior *
A3.4.5.1.1. Control panel - - - -
A3.4.5.1.2. Dimmers/transformer - - - -
A3.4.5.1.3. Control box - - - -
A3.4.5.1.4. Light assemblies - - - -
A3.4.5.1.5. Power supply - - - -
A3.4.5.2. Exterior
A3.4.5.2.1.. Navigation/formation - - - -
A3.4.5.2.2. Anti-collision - - - -
A3.4.5.2.3. Strobe - - - -
A3.4.5.2.4. Surge suppressor - - - -
A3.4.5.2.5.. Strobe light power supply - - - -
A3.4.5.2.6. Landing light - - - -
A3.4.5.2.7. Taxi light - - - -
A3.4.5.2.8. Terrain clearance lights - - - -
A3.4.5.3. Emergency
A3.4.5.3.1. Emergency exit lights - - - -
A3.4.5.3.2. Control box - - - -
A3.4.5.3.3. Power supply - - - -
A3.4.5.3.4. UARRSI/AR receptacle - - - -
A3.4.5.3.5. Slipway lights - - - -
A3.4.5.3.6. Area lights - - - -
A3.4.6. Repair components
A3.4.6.1. Interior
A3.4.6.1.1. Control panel - - - -
A3.4.6.1.2. Control box - - - -
A3.4.6.1.3. Light assemblies - - - -
A3.4.6.2. Exterior
GENERIC TRAINING REQUIREMENTSSTS 2A6X6, October 2002
36Attachment 3
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A3.4.6.2.1. Navigation/formation - - - -
A3.4.6.2.2. Anti-collision - - - -
A3.4.6.2.3. Strobe - - - -
A3.4.6.2.4. Landing light - - - -
A3.4.6.2.5. Taxi light - - - -
A3.4.6.2.6. Terrain clearance lights - - - -
A3.4.6.3. Emergency exit lights - - - -
A3.4.7. Install components
A3.4.7.1. Interior *
A3.4.7.1.1. Control panel - - - -
A3.4.7.1.2. Dimmers/transformer - - - -
A3.4.7.1.3. Control box - - - -
A3.4.7.1.4. Light assemblies - - - -
A3.4.7.1.5. Power supply - - - -
A3.4.7.2. Exterior
A3.4.7.2.1. Navigation/formation - - - -
A3.4.7.2.2. Anti-collision - - - -
A3.4.7.2.3. Strobe - - - -
A3.4.7.2.4. Surge suppressor - - - -
A3.4.7.2.5. Strobe light power supply - - - -
A3.4.7.2.6. Landing light - - - -
A3.4.7.2.7. Taxi light - - - -
A3.4.7.2.8. Terrain clearance lights - - - -
A3.4.7.3. Emergency
A3.4.7.3.1. Emergency exit lights - - - -
A3.4.7.3.2. Control box - - - -
A3.4.7.3.3. Power supply - - - -
A3.4.7.3.4. UARRSI/AR receptacle - - - -
A3.4.7.3.5. Slipway lights - - - -
A3.4.7.3.6. Area lights - - - -
A3.4.8. Bench check components
A3.4.8.1. Interior
A3.4.8.1.1. Control panel - - - -
A3.4.8.1.2. Control box - - - -
A3.4.8.1.3. Light assemblies - - - -
A3.4.8.2. Exterior
A3.4.8.2.1. Navigation/formation - - - -
A3.4.8.2.2. Anti-collision - - - -
GENERIC TRAINING REQUIREMENTSSTS 2A6X6, October 2002
37Attachment 3
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A3.4.8.2.3. Strobe - - - -
A3.4.8.2.4. Landing light - - - -
A3.4.8.2.5. Taxi light - - - -
A3.4.8.2.6. Terrain clearance lights - - - -
A3.4.8.3. Emergency exit lights - - - -
A3.5. LANDING GEAR SYSTEM
TR: Applicable aircraft TOs, 8 series component TOs
A3.5.1. Operational fundamentals
*A3.5.1.1. Control B B - -
*A3.5.1.2. Warning and indication B B - -
A3.5.2. Operational check
*A3.5.2.1. Control 2b - - -
A3.5.2.2. Position A - - - -
A3.5.2.3. Position B - - - -
A3.5.2.4. Position C - - - -
*A3.5.2.5. Warning and indication 2b - - -
A3.5.2.6. Crosswind crab system - - - -
A3.5.2.7. Interrogate proximity interference unit - - - -
A3.5.3. Troubleshoot
*A3.5.3.1. Control * 2b B - C
*A3.5.3.2. Warning and indication * 2b B - C
A3.5.3.3. Crosswind crab system - - - -
A3.5.4. Inspect system components * - - - -
A3.5.5. Remove components
A3.5.5.1. Landing gear control panel - - - -
A3.5.5.2. Landing gear control relay box - - - -
A3.5.5.3. Junction box - - - -
A3.5.5.4. Audible warning control - - - -
A3.5.5.5. Warning horn - - - -
A3.5.6. Repair components
A3.5.6.1. Landing gear control panel - - - -
A3.5.6.2. Landing gear control relay box - - - -
A3.5.6.3. Junction box - - - -
A3.5.6.4. Warning horn - - - -
A3.5.7. Install components
A3.5.7.1. Landing gear control panel - - - -
A3.5.7.2. Landing gear control relay box - - - -
A3.5.7.3. Junction box - - - -
GENERIC TRAINING REQUIREMENTSSTS 2A6X6, October 2002
38Attachment 3
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A3.5.7.4. Audible warning control - - - -
A3.5.7.5. Warning horn - - - -
A3.5.8. Bench check components
A3.5.8.1. Landing gear control panel - - - -
A3.5.8.2. Landing gear control relay box - - - -
A3.5.8.3. Junction box - - - -
A3.5.8.4. Warning horn - - - -
A3.6. ANTI-SKID SYSTEM
TR: Applicable aircraft TOs, 8 series component TOs
*A3.6.1. Operational fundamentals B B - -
*A3.6.2. Operational check 2b - - -
*A3.6.3. Troubleshoot * 2b B - -
A3.6.4. Inspect system components * - - - -
A3.6.5. Remove components
A3.6.5.1. Anti-skid control box - - - -
A3.6.5.2. Anti-skid transducer - - - -
A3.6.5.3. Spin-up control box - - - -
A3.6.6. Install components
A3.6.6.1. Anti-skid control box - - - -
A3.6.6.2. Anti-skid transducer - - - -
A3.6.6.3. Spin-up control box - - - -
A3.7. BRAKE TEMPERATURE INDICATING SYSTEM
TR: Applicable aircraft TOs, 8 series component TOs
A3.7.1. Operational Fundamentals - - - -
A3.7.2. Operational Check - - - -
A3.7.3. Troubleshoot - - - -
A3.7.4. Inspect System components - - - -
A3.7.5. Remove components
A3.7.5.1. Temperature control unit - - - -
A3.7.5.2. Temperature sensor - - - -
A3.7.6. Install components
A3.7.6.1. Temperature control unit - - - -
A3.7.6.2. Temperature sensor - - - -
A3.8. NOSE GEAR STEERING SYSTEM
TR: Applicable aircraft TOs, 8 series component TOs
*A3.8.1. Operational fundamentals B B - -
*A3.8.2. Operational check 2b - - -
*A3.8.3. Troubleshoot 2b B - -
GENERIC TRAINING REQUIREMENTSSTS 2A6X6, October 2002
39Attachment 3
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A3.8.4. Inspect System Components - - - -
A3.8.5. Remove components
A3.8.5.1. Control unit - - - -
A3.8.5.2. Transducer - - - -
A3.8.6. Repair transducer - - - -
A3.8.7. Install components
A3.8.7.1. Control unit - - - -
A3.8.7.2. Transducer - - - -
A3.9. PRIMARY FLIGHT CONTROL SYSTEM
TR: Applicable aircraft TOs, 8 series component TOs
*A3.9.1. Operational fundamentals B B - -
A3.9.2. Operational check
A3.9.2.1. Control system - - - -
A3.9.2.2. Trim/indication system - - - -
A3.9.3. Troubleshoot
A3.9.3.1. Control system - - - -
A3.9.3.2. Trim/indication system - B - -
A3.9.4. Inspect System Components - - - -
A3.10. SECONDARY FLIGHT CONTROL SYSTEM
TR: Applicable aircraft TOs, 8 series component TOs
*A3.10.1. Operational fundamentals B B - -
A3.10.2. Operational check
*A3.10.2.1. Flaps 2b - - -
A3.10.2.2. Trim - - - -
*A3.10.2.3. Speed brakes 2b - - -
A3.10.2.4. Spoilers - - - -
A3.10.3. Troubleshoot
*A3.10.3.1. Flaps 2b B - -
A3.10.3.2. Trim - - - -
*A3.10.3.3. Speed brakes 2b B - -
A3.10.3.4. Spoilers - - - -
A3.10.4. Inspect System Components - - - -
A3.10.5. Remove components
A3.10.5.1. Emergency Flight Control Panel - - - -
A3.10.5.2. Speed brake Cam limit switch - - - -
A3.10.5.3. Flap position control unit - - - -
A3.10.5.4 Flight control relay box - - - -
A3.10.6. Repair components
GENERIC TRAINING REQUIREMENTSSTS 2A6X6, October 2002
40Attachment 3
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A3.10.6.1. Emergency Flight Control Panel - - - -
A3.10.6.2. Flight control relay box - - - -
A3.10.7. Install components
A3.10.7.1. Emergency Flight Control Panel - - - -
A3.10.7.2. Speed brake Cam limit switch - - - -
A3.10.7.3. Flap position control unit - - - -
A3.10.7.4. Flight control relay box - - - -
A3.11. OVERHEAT/FIRE WARNING SYSTEM
TR: Applicable aircraft TOs, 8 series component TOs
A3.11.1. Operational fundamentals
*A3.11.1.1. Engine/pylon B B - -
A3.11.1.2. Smoke detection - - - -
A3.11.1.3. APU - - - -
A3.11.1.4. Bleed air overheat - - - -
A3.11.1.5. Wing overheat - - - -
A3.11.2. Operational check
*A3.11.2.1. Engine/pylon 2b - - -
A3.11.2.2. Smoke detection - - - -
A3.11.2.3. APU - - - -
A3.11.2.4. Bleed air overheat - - - -
A3.11.2.5. Wing overheat - - - -
A3.11.3. Troubleshoot
*A3.11.3.1. Engine/pylon 2b B - -
A3.11.3.2. Smoke detection - - - -
A3.11.3.3. APU - - - -
A3.11.3.4. Bleed air overheat - - - -
A3.11.3.5. Wing overheat - - - -
A3.11.4. Inspect System Components * - - - -
A3.11.5. Remove components
A3.11.5.1. Sensing elements - - - -
A3.11.5.2. Smoke detectors - - - -
A3.11.5.3. Bleed air overheat control box - - - -
A3.11.5.4. Fire/overheat detectors - - - -
A3.11.5.5. Flasher control unit - - - -
A3.11.6. Adjust fire/overheat detectors - - - -
A3.11.7. Install components
A3.11.7.1. Sensing elements - - - -
A3.11.7.2. Smoke detectors - - - -
GENERIC TRAINING REQUIREMENTSSTS 2A6X6, October 2002
41Attachment 3
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A3.11.7.3. Bleed air overheat control box - - - -
A3.11.7.4. Fire/overheat detectors - - - -
A3.11.7.5. Flasher control unit - - - -
A3.11.8. Bench check fire/overheat detectors - - - -
A3.12. FIRE EXTINGUISHING SYSTEM
TR: Applicable aircraft TOs, 8 series component TOs
A3.12.1. Operational fundamentals
*A3.12.1.1. Engine B B - -
A3.12.1.2. APU - - - -
A3.12.1.3. Wing - - - -
A3.12.2. Operational check
*A3.12.2.1. Engine 2b - -
A3.12.2.2. APU - - - -
A3.12.2.3. Wing - - - -
A3.12.2.4. Fire doors - - - -
A3.12.3. Troubleshoot
*A3.12.3.1. Engine 2b B - -
A3.12.3.2. APU - - - -
A3.12.3.3. Wing - - - -
A3.12.3.4.. Fire doors - - - -
A3.12.4. Inspect System Components - - - -
A3.12.5. Remove components
A3.12.5.1. Engine fire bottle - - - -
A3.12.5.2. APU fire bottle - - - -
*A3.12.5.3. Squib/cartridge * a - - -
A3.12.5.4. Wing fire bottle - - - -
A3.12.5.5 Resistor box - - - -
A3.12.5.6 T handle assembly - - - -
A3.12.5.7 Suppressor - - - -
A3.12.6. Repair components
A3.12.6.1. Resistor box - - - -
A3.12.6.2. T handle assembly - - - -
A3.12.7. Install components
A3.12.7.1.. Engine fire bottle - - - -
A3.12.7.2. APU fire bottle - - - -
*A3.12.7.3. Squib/cartridge * a - - -
A3.12.7.4. Wing fire bottle - - - -
A3.12.7.5. Resistor box - - - -
GENERIC TRAINING REQUIREMENTSSTS 2A6X6, October 2002
42Attachment 3
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A3.12.7.6. T handle assembly - - - -
A3.12.7.7. Suppressor - - - -
A3.12.8. Bench check components
A3.12.8.1. Resistor box - - - -
A3.12.8.2. T handle assembly - - - -
A3.13. TAKEOFF WARNING SYSTEM
TR: Applicable aircraft TOs, 8 series component TOs
A3.13.1. Operational fundamentals - B - -
A3.13.2. Operational check - - - -
A3.13.3. Troubleshoot - B - -
A3.13.4. Inspect system components - - - -
A3.13.5. Components location - - - -
A3.13.6. Adjust position switches - - - -
A3.14. MASTER CAUTION/WARNING SYSTEM
TR: Applicable aircraft TOs, 8 series component TOs
*A3.14.1. Operational fundamentals B B - -
*A3.14.2. Operational check * 2b - - -
*A3.14.3. Troubleshoot 2b B - -
A3.14.4. Inspect System Components - - - -
A3.14.5. Remove components
A3.14.5.1. Controller - - - -
A3.14.5.2. Flasher - - - -
A3.14.5.3. Annunciator panel - - - -
A3.14.5.4. Light assembly - - - -
A3.14.6. Repair components
A3.14.6.1. Controller - - - -
A3.14.6.2. Annunciator panel - - - -
A3.14.7. Install components
A3.14.7.1. Controller - - - -
A3.14.7.2. Flasher - - - -
A3.14.7.3. Annunciator panel - - - -
A3.14.7.4. Light assembly - - - -
A3.14.8. Bench check components
A3.14.8.1. Controller - - - -
A3.14.8.2. Annunciator panel - - - -
A3.15. DOOR CONTROL AND WARNING SYSTEM
TR: Applicable aircraft TOs, 8 series component TOs
A3.15.1. Cargo doors
GENERIC TRAINING REQUIREMENTSSTS 2A6X6, October 2002
43Attachment 3
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
*A3.15.1.1. Operational fundamentals B B - -
*A3.15.1.2. Troubleshoot Cargo door control and warning system b B - -
A3.15.2 Weapons doors
A3.15.2.1 Operational fundamentals - - - -
A3.15.2.2. Operational check - - - -
A3.15.2.3 Troubleshoot - - - -
A3.15.2.4 Inspect System Components - - - -
A3.15.3 Adjust switches - - - -
A3.16. FUEL WARNING AND CONTROL SYSTEM
TR: Applicable aircraft TOs, 8 series component TOs
A3.16.1. Operational fundamentals - B - -
A3.16.2. Operational check
A3.16.2.1. Fuel warning and control system - - - -
A3.16.2.2. In-flight refueling (IFR)/Universal aerial refueling receptacle slip way installation (UARRSI) system
- - - -
A3.16.2.3. Ground refuel system - - - -
A3.16.3. Troubleshoot
A3.16.3.1. Fuel warning and control system - B - -
A3.16.3.2. In-flight refueling (IFR)/Universal aerial refueling receptacle slipway installation (UARRSI) system
- - - -
A3.16.3.3. Ground refuel system - - - -
A3.16.4. Inspect System Components - - - -
A3.16.5. Remove components
A3.16.5.1. Fuel management switches - - - -
A3.16.5.2. Single point refueling panel - - - -
A3.16.5.3. Fuel management panel - - - -
A3.16.5.4. Fuel & engine control relay box - - - -
A3.16.6. Repair components
A3.16.6.1. Single point refueling panel - - - -
A3.16.6.2. Fuel management panel - - - -
A3.16.6.3. Fuel & engine control relay box - - - -
A3.16.7. Install components
A3.16.7.1. Fuel management switches - - - -
A3.16.7.2. Single point refueling panel - - - -
A3.16.7.3. Fuel management panel - - - -
A3.16.7.4. Fuel & engine control relay box - - - -
A3.16.8. Bench check components
A3.16.8.1. Single point refueling panel - - - -
GENERIC TRAINING REQUIREMENTSSTS 2A6X6, October 2002
44Attachment 3
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A3.16.8.2. Fuel management panel - - - -
A3.16.8.3. Fuel & engine control relay box - - - -
A3.17. START AND IGNITION SYSTEM
TR: Applicable aircraft TOs, 8 series component TOs
A3.17.1. Operational fundamentals - B - -
A3.17.2. Operational check
A3.17.2.1. Jet engine - - - -
A3.17.2.2. APU - - - -
A3.17.2.3. Cartridge start - - - -
A3.17.3. Troubleshoot
A3.17.3.1 Engine - B - -
A3.17.3.2 APU - B - -
A3.17.3.2. Cartridge start - - - -
A3.17.4. Inspect System Components - - - -
A3.17.5. Repair components
A3.17.5.1. Centrifugal switch - - - -
A3.17.5.2. Breech cap - - - -
A3.17.5.3. Throttle quadrant - - - -
A3.17.6. Bench check components
A3.17.6.1. Breech cap - - - -
A3.17.6.2. Throttle quadrant - - - -
A3.17.7. Components location - - - -
A3.18. NESA ANTI-ICING SYSTEM
TR: Applicable aircraft TOs, 8 series component TOs
*A3.18.1. Operational fundamentals B B - -
*A3.18.2. Operational check 2b - - -
*A3.18.3. Troubleshoot 2b B - -
A3.18.4. Inspect System Components - - - -
A3.18.5. Remove components
A3.18.5.1. Temperature controller - - - -
A3.18.5.2. Windshield heat control box - - - -
A3.18.5.3. Thermal snap switch - - - -
A3.18.5.4. Transformers - - - -
A3.18.6. Install components
A3.18.6.1. Temperature controller - - - -
A3.18.6.2. Windshield heat control box - - - -
A3.18.6.3. Thermal snap switch - - - -
A3.18.6.4. Transformers - - - -
GENERIC TRAINING REQUIREMENTSSTS 2A6X6, October 2002
45Attachment 3
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A3.19. BLEED AIR DISTRIBUTION SYSTEM
TR: Applicable aircraft TOs, 8 series component TOs
*A3.19.1. Operational fundamentals B B - -
*A3.19.2. Operational check * 2b - -
*A3.19.3. Troubleshoot * 2b B - C
A3.19.4. Inspect System Components - - - -
A3.19.5. Remove components
*A3.19.5.1. Ducts 2b - - -
A3.19.5.2. Insulation blankets - - - -
*A3.19.5.3. Check valve 2b - - -
*A3.19.5.4. Pressure regulator/shutoff valve 2b - - -
A3.19.5.5. Engine bleed air distribution valve - - - -
A3.19.5.6. Ejector valve - - - -
A3.19.5.7. By-pass valve - - - -
A3.19.5.8. Pre-cooler - - - -
A3.19.5.9. Pre-cooler temperature control valve - - - -
A3.19.5.10. Pre-cooler temperature control box - - - -
A3.19.5.11. Temperature sensor - - - -
A3.19.5.12. Pressure sensor - - - -
A3.19.6. Install components
*A3.19.6.1. Ducts 2b - - -
A3.19.6.2. Insulation blankets - - - -
*A3.19.6.3. Check valve 2b - - -
*A3.19.6.4. Pressure regulator/shutoff valve 2b - - -
A3.19.6.5. Engine bleed air distribution valve - - - -
A3.19.6.6. Ejector valve - - - -
A3.19.6.7. By-pass valve - - - -
A3.19.6.8. Pre-cooler - - - -
A3.19.6.9. Pre-cooler temperature control valve - - - -
A3.19.6.10. Pre-cooler temperature control box - - - -
A3.19.6.11. Temperature sensor - - - -
A3.19.6.12. Pressure sensor - - - -
*A3.19.7. Perform leakage checks * 2b B - -
A3.19.8. Perform leak check with nitrogen cart - - - -
A3.19.9. Perform duct hydrostatic check - - - -
A3.20. AIR CONDITIONING SYSTEM
TR: Applicable aircraft TOs, 8 series component TOs
*A3.20.1. Operational fundamentals B B - -
GENERIC TRAINING REQUIREMENTSSTS 2A6X6, October 2002
46Attachment 3
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A3.20.2. Subsystem fundamentals
*A3.20.2.1. Anti-G suit system B B - -
*A3.20.2.2. Defogging system B B - -
*A3.20.2.3. Rain removal system B B - -
A3.20.2.4. Primary heat exchanger - - - -
A3.20.2.5. Secondary heat exchanger - - - -
A3.20.2.6. Temperature control - - - -
A3.20.2.7. Low limit 35°control - - - -
A3.20.2.8. Avionics/equipment cooling - - - -
A3.20.2.9. Ram air - - - -
A3.20.3. Operational check
*A3.20.3.1. Air conditioning systems 2b - - -
A3.20.3.2. Anti-G suit system - - - -
A3.20.3.3. Defogging system - - - -
A3.20.3.4. Rain removal system - - - -
A3.20.3.5. Primary heat exchanger - - - -
A3.20.3.6. Secondary heat exchanger - - - -
A3.20.3.7. Temperature control - - - -
A3.20.3.8. Low limit 35°control - - - -
A3.20.3.9. Avionics/equipment cooling - - - -
A3.20.3.10. Ram air - - - -
A3.20.3.11. Cabin heat control - - - -
A3.20.3.12. Interrogate environmental control system controller - - - -
A3.20.4. Troubleshoot
*A3.20.4.1. Air conditioning systems * 2b B - C
A3.20.4.2. Anti-G suit system - - - -
A3.20.4.3. Defogging system - - - -
A3.20.4.4. Rain removal system - - - -
A3.20.4.5. Primary heat exchanger - - - -
A3.20.4.6. Secondary heat exchanger - - - -
A3.20.4.7. Temperature control - - - -
A3.20.4.8. Low limit 34°control - - - -
A3.20.4.9. Avionics/equipment cooling - - - -
A3.20.4.10. Ram air - - -
A3.20.4.11. Cabin heat control - - - -
A3.20.5. Inspect System Components - - 3c -
A3.20.6. Remove components
A3.20.6.1. Water separator - - - -
GENERIC TRAINING REQUIREMENTSSTS 2A6X6, October 2002
47Attachment 3
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
*A3.20.6.1. Water separator coalescer * 2b - - -
A3.20.6.2. Air conditioning pack - - - -
A3.20.6.3. Catalytic filter - - - -
A3.20.6.4. ECS over pressure switch - - - -
A3.20.6.5. ECS pressure regulator valve - - - -
A3.20.6.6. Temperature control box - - - -
A3.20.6.7. Primary heat exchanger - - - -
A3.20.6.8. Secondary heat exchanger - - - -
A3.20.6.9. Temperature sensor - - - -
A3.20.6.10. ECS control panel - - - -
A3.20.6.11 Cabin duct heater - - - -
A3.20.6.12. Ejector valve - - - -
A3.20.6.13. Ram air plenum - - - -
A3.20.6.14. Ram air valve - - - -
A3.20.6.15. Turbines - - - -
A3.20.6.16. Pack Anti-ice valve - - - -
A3.20.6.17. Temperature control valve - - - -
A3.20.6.18. Stores cooling valve - - - -
A3.20.6.19. CTCS controller - - - -
A3.20.6.20. ACS/MCS controller - - - -
A3.20.6.21. Anti-G suit valve/hose - - - -
A3.20.6.22. Defog valve - - - -
A3.20.6.23. Rain removal valve - - - -
A3.20.6.24. Air conditioning control switch - - - -
A3.20.6.25. Ducts - - - -
A3.20.6.26. Recirculation/electric/electronic cooling/vanaxial fan
- - - -
A3.20.7. Repair components
A3.20.7.1. Water separator - - - -
A3.20.7.2. ECS control panel - - - -
A3.20.7.3. Ducts - - - -
A3.20.7.4. Catalytic filter - - - -
A3.20.7.5. Recirculation/electric/electronic cooling/vanaxialfan
- - - -
A3.20.8. Install components
A3.20.8.1. Water separator - - - -
*A3.20.8.2. Water separator coalescer * 2b - - -
A3.20.8.3. Air conditioning pack - - - -
GENERIC TRAINING REQUIREMENTSSTS 2A6X6, October 2002
48Attachment 3
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A3.20.8.4. Catalytic filter - - - -
A3.20.8.5. ECS over pressure switch - - - -
A3.20.8.6. ECS pressure regulator valve - - - -
A3.20.8.7. Temperature control box - - - -
A3.20.8.8. Primary heat exchanger - - - -
A3.20.8.9. Secondary heat exchanger - - - -
A3.20.8.10. Temperature sensor - - - -
A3.20.8.11. ECS control panel - - - -
A3.20.8.12. Cabin duct heater - - - -
A3.20.8.13. Ejector valve - - - -
A3.20.8.14. Ram air plenum - - - -
A3.20.8.15. Ram air valve - - - -
A3.20.8.16. Turbines - - - -
A3.20.8.17. Pack Anti-ice valve - - - -
A3.20.8.18. Temperature control valve - - - -
A3.20.8.19. Stores cooling valve - - - -
A3.20.8.20. CTCS controller - - - -
A3.20.8.21. ACS/MCS controller - - - -
A3.20.8.22. Anti-G suit valve/hose - - - -
A3.20.8.23. Defog valve - - - -
A3.20.8.24. Rain removal valve - - - -
A3.20.8.25. Air conditioning control switch - - - -
A3.20.8.26. Ducts - - - -
A3.20.8.27. Recirculation/electric/electronic cooling/vanaxial fan
- - - -
*A3.20.9. Perform leakage checks * 1b B - -
A3.20.10 Bench check fans - - - -
A3.20.11 Perform duct hydrostatic test - - - -
.A3.20.12. Service turbine - - - -
A3.21. PRESSURIZATION SYSTEM
TR: Applicable aircraft TOs, 8 series component TOs
A3.21.1. Operational fundamentals
*A3.21.1.1. Aircraft pressurization system B B - -
*A3.21.1.2. Canopy seal system B B - -
A3.21.1.3. Fuel tank pressurization - - - -
A3.21.2. Operational check
*A3.21.2.1. Pressurization system *R 2b - - -
A3.21.2.2. Canopy seal system - - - -
GENERIC TRAINING REQUIREMENTSSTS 2A6X6, October 2002
49Attachment 3
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A3.21.2.3. Fuel tank pressurization - - - -
A3.21.3. Troubleshoot
*A3.21.3.1. Pressurization system * 2b B - C
A3.21.3.2. Canopy seal system - - - -
A3.21.3.3. Fuel tank pressurization - - - -
A3.21.4. Inspect System Components - - - -
A3.21.5. Remove components
A3.21.5.1. Cabin pressure regulator/controller - - - -
A3.21.5.2. Cabin safety valve - - - -
A3.21.5.3. Outflow valve - - - -
A3.21.5.4. Pneumatic relay - - - -
A3.21.5.5. Canopy seal regulator - - - -
A3.21.5.6. Canopy seal - - - -
A3.21.5.7. Cabin pressure altimeter - - - -
A3.21.5.8. Central equipment bay regulator - - - -
A3.21.5.9. Forward equipment bay regulator - - - -
A3.21.5.10. Aft equipment bay regulator - - - -
A3.21.5.11. Low altitude switch - - - -
A3.21.5.12. High altitude switch - - - -
A3.21.5.13. Check valve - - - -
A3.21.5.14. Filters - - - -
A3.21.6. Install components
A3.21.6.1. Cabin pressure regulator/controller - - - -
A3.21.6.2. Cabin safety valve - - - -
A3.21.6.3. Outflow valve - - - -
A3.21.6.4. Pneumatic relay - - - -
A3.21.6.5. Canopy seal regulator - - - -
A3.21.6.6. Canopy seal - - - -
A3.21.6.7. Cabin pressure altimeter - - - -
A3.21.6.8. Central equipment bay regulator - - - -
A3.21.6.9. Forward equipment bay regulator - - - -
A3.21.6.10. Aft equipment bay regulator - - - -
A3.21.6.11. Low altitude switch - - - -
A3.21.6.12. High altitude switch - - - -
A3.21.6.13. Check valve - - - -
A3.21.6.14. Filters - - - -
A3.22. LIQUID COOLANT SYSTEM
TR: Applicable aircraft TOs, 8 series component TOs
GENERIC TRAINING REQUIREMENTSSTS 2A6X6, October 2002
50Attachment 3
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
*A3.22.1. Operational fundamentals B B - -
A3.22.2. Troubleshoot - - - -
A3.22.3. Inspect System Components - - - -
A3.22.4. Remove components
A3.22.4.1. Pump - - - -
A3.22.4.2. Heat exchanger - - - -
A3.22.4.3. Reservoir - - - -
A3.22.4.4. Filter - - - -
A3.22.4.5. Pressure regulator - - - -
A3.22.4.6. Test control panel - - - -
A3.22.4.7. Pressure/temperature Sensors - - - -
A3.22.5. Install components
A3.22.5.1. Pump - - - -
A3.22.5.2. Heat exchanger - - - -
A3.22.5.3. Reservoir - - - -
A3.22.5.4. Filter - - - -
A3.22.5.5. Pressure regulator - - - -
A3.22.5.6. Test control panel - - - -
A3.22.5.7. Pressure/temperature Sensors - - - -
A3.22.6. Service and recovery - - - -
A3.23. OXYGEN SYSTEMS
TR: AFOSH standards; TOs 15X1-1, 42B5-1-2, 42E1-1-1, applicable aircraft TOs, 8 series component TOs
A3.23.1. Liquid oxygen system
*A3.23.1.1. Operational fundamentals B B - -
A3.23.1.2. Operational check
*A3.23.1.2.1. Crew 2b - - -
*A3.23.1.2.2. LOX indicating 2b - - -
A3.23.1.2.3. Oxygen regulator - - - -
A3.23.1.3. Troubleshoot
*A3.23.1.3.1. Crew 2b - - -
A3.23.1.3.2. PT LOX - - - -
A3.23.1.3.3. LOX indicating - - - -
A3.23.1.4. Inspect System Components * - B 3c -
A3.23.1.5. Purge system
*A3.23.1.5.1. Purge converter 2b B - -
A3.23.1.6. Remove components
GENERIC TRAINING REQUIREMENTSSTS 2A6X6, October 2002
51Attachment 3
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A3.23.1.6.1. Converter - - - -
A3.23.1.6.2. Build-up/fill and vent valve - - - -
A3.23.1.6.3. Check valves - - - -
A3.23.1.6.4. Indicator/totalizer - - - -
A3.23.1.6.5. Distribution tubing/hoses - - - -
A3.23.1.6.6. Heat exchanger - - - -
*A3.23.1.6.7. Oxygen regulator * 2b B - -
A3.23.1.7. Repair components
A3.23.1.7.1. Converter - - - -
A3.23.1.7.2. PT LOX converter - - - -
A3.23.1.8. Install components
A3.23.1.8.1. Converter - - - -
A3.23.1.8.2. Build-up/fill and vent valve - - - -
A3.23.1.8.3. Check valves - - - -
A3.23.1.8.4. Indicator/totalizer - - - -
A3.23.1.8.5. Distribution tubing/hoses - - - -
A3.23.1.8.6. Heat exchanger - - - -
*A3.23.1.8.7. Oxygen regulator * 2b B - -
*A3.23.1.9. Perform leak check * 2b B - -
*A3.23.1.10. Clean components & tools * B - - -
A3.23.1.11. Drain system
A3.23.1.11.1. Converter - - - -
A3.23.1.11.2. PT LOX converter - - - -
A3.23.1.12. Service system
A3.23.1.12.1. Converter - - - -
A3.23.1.12.2. PT LOX converter - - - -
A3.23.2. Gaseous oxygen system
*A3.23.2.1. Operational fundamentals B B - -
A3.23.2.2. Operational check
A3.23.2.2.1. Back-up oxygen system - - - -
A3.23.2.2.2. Oxygen Regulator - - - -
A3.23.2.2.3. Selector Flow switch - - - -
*A3.23.2.2.4. High/Low pressure systems 2b - - -
A3.23.2.3. Troubleshoot
A3.23.2.3.1. Back-up oxygen system - - - -
A3.23.2.3.2. Oxygen Regulator - - - -
A3.23.2.3.3. Selector Flow switch - - - -
A3.23.2.3.4. High/Low pressure systems - B - -
GENERIC TRAINING REQUIREMENTSSTS 2A6X6, October 2002
52Attachment 3
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A3.23.2.4. Inspect System Components - B - -
A3.23.2.5. Purge system - B - -
A3.23.2.6. Remove components - - - -
A3.23.2.6.1. Bottle - - - -
A3.23.2.6.2. Service/drain valve - - - -
A3.23.2.6.3. Regulator - - - -
A3.23.2.6.4. Check valve - - - -
A3.23.2.6.5. Shutoff valve - - - -
A3.23.2.6.6. Low pressure switch - - - -
A3.23.2.6.7. Distribution tubing/hoses - - - -
A3.23.2.6.8. Walk around bottle regulator - - - -
A3.23.2.6.9. Selector flow switch - - - -
A3.23.2.7. Repair bail out bottle - - - -
A3.23.2.8. Install components
A3.23.2.8.1. Bottle - - - -
A3.23.2.8.2. Service/drain valve - - - -
A3.23.2.8.3. Regulator - - - -
A3.23.2.8.4. Check valve - - - -
A3.23.2.8.5. Shutoff valve - - - -
A3.23.2.8.6. Low pressure switch - - - -
A3.23.2.8.7. Distribution tubing/hoses - - - -
A3.23.2.8.8. Walk around bottle regulator - - - -
A3.23.2.8.9. Selector flow switch - - - -
*A3.23.2.9. Perform leak check 2b - - -
A3.23.2.10. Clean components and tools * - - - -
A3.23.2.11. Purge system - - - -
A3.23.2.12. Drain system - - - -
A3.23.2.13. Service system - - - -
A3.23.3. Self-generating oxygen system
*A3.23.3.1. Operational fundamentals B B - -
A3.23.3.2. Operational check - - - -
A3.23.3.3. Troubleshoot - - - -
A3.23.3.4. Inspect System Components * - - - -
A3.23.3.5. Purge system - - - -
A3.23.3.6. Remove components
A3.23.3.6.1. Concentrator - - - -
A3.23.3.6.2. Partial filter - - - -
A3.23.3.6.3. Controller - - - -
GENERIC TRAINING REQUIREMENTSSTS 2A6X6, October 2002
53Attachment 3
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A3.23.3.7. Install components
A3.23.3.7.1. Concentrator - - - -
A3.23.3.7.2. Partial filter - - - -
A3.23.3.7.3. Controller - - - -
A3.23.3.8. Perform leak check - - - -
A3.23.3.9. Clean components and tools * - - - -
A3.24. OBIGGS
TR: Applicable aircraft TOs, 8 series component TOs
A3.24.1. Operational fundamentals - - - -
A3.24.2. Operational check - - - -
A3.24.3. Troubleshoot - - - -
A3.24.4. Inspect Concentrator - - - -
A3.24.5. Remove Concentrator - - - -
A3.24.6. Install Concentrator - - - -
A3.24.7. Perform leakage checks - - - -
A3.25. MISCELLANEOUS SYSTEMS
TR: Applicable aircraft/equipment TOs, 8 series component TOs
A3.25.1. Operational fundamentals
A3.25.1.1. Aircrew eye respiratory protection system (AERP) - - - -
A3.25.1.2. Thermal flash/protection power sources - - - -
A3.25.1.3. Windshield/wiper - - - -
A3.25.1.4. Windshield Wash System - - - -
*A3.25.1.5. Wing anti-icing system B B - -
A3.25.1.6. Cowl/Nacelle anti-ice - - - -
A3.25.1.7. Engine anti-ice - - - -
A3.25.1.8. De-icing - - - -
A3.25.2. Operational check
A3.25.2.1. Aircrew eye respiratory protection system (AERP) - - - -
A3.25.2.2. Thermal flash/protection power sources - - - -
A3.25.2.3.. Windshield/wiper - - - -
A3.25.2.4.. Windshield Wash System - - - -
A3.25.2.5.. Wing anti-icing system * - - - -
A3.25.2.6... Cowl/Nacelle anti-ice - - - -
A3.25.2.7.. Engine anti-ice - - - -
A3.25.2.8.. De-icing - - - -
A3.25.3. Troubleshoot
A3.25.3.1.. Aircrew eye respiratory protection system (AERP) - - - -
GENERIC TRAINING REQUIREMENTSSTS 2A6X6, October 2002
54Attachment 3
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A3.25.3.2. Thermal flash/protection power sources - - - -
A3.25.3.3. Windshield/wiper - - - -
A3.25.3.4. Windshield Wash System - - - -
A3.25.3.5. Wing anti-icing system - - - -
A3.25.3.6. Cowl/Nacelle anti-ice - - - -
A3.25.3.7. Engine anti-ice - - - -
A3.25.3.8. De-icing - - - -
A3.25.4. Inspect System Components - - - -
A3.25.5. Remove Components
A3.25.5.1. AERP control box - - - -
A3.25.5.2. Thermal Flash Conditioner - - - -
A3.25.5.3. Windshield wash control valve - - - -
A3.25.5.4. Windshield wash purge valve - - - -
A3.25.5.5. Windshield wash reservoir - - - -
A3.25.5.6. Miscellaneous relay box - - - -
A3.25.5.7. Cowl/Nacelle anti-ice
A3.25.5.7.1. Modulation/shutoff valve - - - -
A3.25.5.7.2. Temp Sensor/thermal switch - - - -
A3.25.5.7.3. Controller - - - -
A3.25.5.8. De-ice
A3.25.5.8.1. Boots - - - -
A3.25.5.8.2. Sequence Valve - - - -
A3.25.6. Repair components
A3.25.6.1. Windshield wash reservoir - - - -
A3.25.6.2. Miscellaneous relay box - - - -
A3.25.7. Install components
A3.25.7.1. AERP control box - - - -
A3.25.7.2. Thermal Flash Conditioner - - - -
A3.25.7.3. Windshield wash control valve - - - -
A3.25.7.4. Windshield wash purge valve - - - -
A3.25.7.5. Windshield wash reservoir - - - -
A3.25.7.6. Miscellaneous relay box - - - -
A3.25.7.7. Cowl/Nacelle anti-ice
A3.25.7.7.1. Modulation/shutoff valve - - - -
A3.25.7.7.2. Temp Sensor/thermal switch - - - -
A3.25.7.7.3. Controller - - - -
A3.25.7.8 De-ice
A3.25.7.8.1. Boots - - - -
GENERIC TRAINING REQUIREMENTSSTS 2A6X6, October 2002
55Attachment 3
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A3.25.7.8.2. Sequence Valve - - - -
A3.25.7.8.3. Bench Check Miscellaneous Relay Box - - - -
CDC 2AX7X TRAINING REQUIREMENTSSTS 2A6X6, October 2002
56Attachment 4
2. Core Tasks
3. Certification For OJT 4. Proficiency Codes Used To IndicateTraining/Information Provided
(See Attachment 1)1. Tasks, Knowledge And Technical References A B C D E A
3 LevelB
5 LevelC
7 Level5 7 Tng
StartTng
CompleteTraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
ATTACHMENT 4:
NOTE 1: Users are responsible for annotating training references to identify current references pending STS revision.
NOTE 2: This attachment is to be used in conjunction with other attachments in applicable CFETPs.
NOTE 3: Personnel must complete CDC requirements on all MDSs/attachments.
NOTE 4: This attachment is to be used as a correlation document for the 2AX7X 7-level Aerospace Maintenance Craftsman CDC’s.
NOTE 5: All items are SUBJECT KNOWLEDGE LEVELS only and require no certification on this STS.
A4.1. MANAGEMENT WITHIN THE MAINTENANCE COMPLEX
TR: AFI 21-101, AFI 21-118 and specific MAJCOM guidance
A4.1.1. Functions of the Maintenance Complex - - - B
A4.1.2. Operations / Logistics Group Commander Responsibilities
TR: AFI 38-101, AFPD 38-1
- - - B
A4.1.3. Accountability and Core Values - - - B
A4.1.4. Aircraft Maintenance Management Information Systems
- - - B
A4.1.5. Aircraft Monitoring - - - B
A4.1.6. Compliance and Standardization Requirements Listings
- - - A
A4.1.7. Maintenance Quality Performance Measures 8(QPM) Relationships
- - - B
A4.1.8. Health-of-the-Fleet Metrics - - - B
A4.1.9. Foreign Object Damage (FOD) Program Manager
TR: AFI 21-101
- - - A
A4.1.10. Joint Oil Analysis Program
TR: T.O. 33-1-37-1
- - - B
A4.1.11. Mobility - - - A
A4.1.12. Hazard Declarations for Mobility Packages
TR: AFMAN 24-204
- - - A
A4.1.13. Hazardous Material Handling Procedures
TR: AFJMAN 24-204, AFI 91-301, AFI 24-202, AFMAN 23-110
- - - B
A4.1.14. Production Supervisor, Flight Chief and Expediter Duties and Responsibilities
- - - B
A4.1.15. Special Certification Rosters - - - B
A4.1.16. Maintenance Incident Investigation and Prevention
TR: AFI 91-204
- - - B
A4.1.17. Aircraft Impoundment
TR: AFI 91-204
- - - A
CDC 2AX7X TRAINING REQUIREMENTSSTS 2A6X6, October 2002
57Attachment 4
2. Core Tasks
3. Certification For OJT 4. Proficiency Codes Used To IndicateTraining/Information Provided
(See Attachment 1)1. Tasks, Knowledge And Technical References A B C D E A
3 LevelB
5 LevelC
7 Level5 7 Tng
StartTng
CompleteTraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A4.1.18. Operational Risk Management (ORM)
TR: AFPD 90-9, AFI 90-901, AFPAM 90-902,
- - - B
A4.1.19. Restricted Maintenance Areas - - - A
A4.1.20. Force Protection
TR: AFDD 2-4.1
- - - A
A4.1.21. Classification Info, Access to Classified, COMSEC, OPSEC, COMPUSEC
TR: AFI 33-211, AFI 10-1101, AFI 33-202
- - - B
A4.1.22. Proper Handling of Classified Assets
TR: AFI 31-101
- - - A
A4.1.23. Aircraft Inspection Concepts
TR: TO 00-20-5
- - - B
A4.2. ENLISTED SPECIALTY TRAINING
TR: AFI 36-2201 and MAJCOM directives
A4.2.1. Training Management and
Records
- - - B
A4.2.2. Automated Training Records - - - B
A4.2.3. Career Field Education and Training Plan (CFETP) - - - B
A4.2.4. Specialty Training Standard (STS) - - - B
A4.2.5. Occupational Survey Report (OSR) - - - B
A4.2.6. Utilization and Training Workshop (U&TW) - - - B
A4.2.7. Training Forecast / Request - - - A
A4.2.8. Training Waiver Process - - - B
A4.2.9. Field Evaluation Questionnaire (FEQ) and Graduate Assessment Survey
- - - A
A4.3. ACCOUNTABILITY FOR RECORDS, REPORTS, AND FORMS
TR: AFI 21-109, TO 00-35D-54, TO 00-20 Seriesand applicable MAJCOM guidance
A4.3.1. Historical Records - - - B
A4.3.2. Minimum Essential Configuration Management (MESL)
- - - B
A4.3.3. Automated Maintenance Systems - - - A
A4.3.4. Reliability Availability, Maintainability, Logistics Engineering Support System for Electronic Attack Pods and Integrated Systems (RAMPOD), Core Automated Maintenance System for Airlift (GO 81)
- - - A
A4.3.5. Core Automated Maintenance System (CAMS)
TR: AFM 66-279 Vol. I-XXVII, T.O. 00-20-2
- - - B
A4.3.6. Job Data Documentation (JDD) - - - B
A4.3.7. Air Force Technical Order (AFTO) Forms 781 and 244 / 245
- - - B
CDC 2AX7X TRAINING REQUIREMENTSSTS 2A6X6, October 2002
58Attachment 4
2. Core Tasks
3. Certification For OJT 4. Proficiency Codes Used To IndicateTraining/Information Provided
(See Attachment 1)1. Tasks, Knowledge And Technical References A B C D E A
3 LevelB
5 LevelC
7 Level5 7 Tng
StartTng
CompleteTraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A4.3.8. Configuration Management - - - B
A4.3.9. Aircraft / Equipment Modifications - - - B
A4.3.10. Nuclear Surety
TR: AFI 91-101
- - - B
A4.3.11. Dull Sword Reporting
TR: AFI 91-204
- - - B
A4.4. SUPPLY MANAGEMENT
TR: DOD 7200-10, AFM 67-1, AFMAN 23-220, AFMAN 23-110 and applicable MAJCOM guidance
A4.4.1. Maintenance Supply Concept
TR: AFMAN 23-110
- - - B
A4.4.2. Supply Documents Management - - - B
A4.4.3. Precious Metal Program
TR: AFMAN 23-110
- - - A
A4.4.4. Bench Stock - - - A
A4.4.5. Air Force Technical Order (AFTO) 375 - - - A
A4.4.6. Quick Reference List (QRL) - - - A
A4.4.7. Standard Base Supply System (SBSS)
TR: AFMAN 23-110
- - - B
A4.4.8. Integrated Logistic System-Supply (ILS-S) and Global Combat Support System (GCSS)
TR: AFMAN 23-110
- - - A
A4.4.9. Priority Systems - - - B
A4.4.10. Repair Cycle Assets - - - B
A4.4.11. Report of Survey, Statement of Charges - - - B
A4.4.12. Equipment Account Management - - - B
A4.4.13. Custodian Authorization/Custody Receipt Listing (CA/CRL)
- - - A
A4.4.14. Precision Measurement Equipment Laboratory (PMEL)
- - - A
A4.4.15. Computer System Management
TR: AFI 33-112
- - - A
A4.4.16. Special Purpose Recoverable Authorized Maintenance(SPRAM)
TR: AFMAN 23-110
- - - A
A4.4.17. Air Force Management System (AFEMS) - - - A
A4.4.18. Status of Resources and Training (SORTS) - - - A
A4.4.19. Land Mobile Radios, Pagers, Cell Phones
TR: AFI 33-106
- - - A
CDC 2AX7X TRAINING REQUIREMENTSSTS 2A6X6, October 2002
59Attachment 4
2. Core Tasks
3. Certification For OJT 4. Proficiency Codes Used To IndicateTraining/Information Provided
(See Attachment 1)1. Tasks, Knowledge And Technical References A B C D E A
3 LevelB
5 LevelC
7 Level5 7 Tng
StartTng
CompleteTraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A4.4.20. Shelf Life Program
TR: AFMAN 23-110
- - - A
A4.4.21. Hazardous Materials (HAZMAT)
TR: Applicable AFOSH STD’s, AFI’s and MAJCOM guidance
- - - B
A4.4.22. Qualified Products Listing - - - B
A4.5. LOGISTICS AND RESOURCE MANAGEMENT
AFPD 21-1
A4.5.1. Logistics Management - - - B
A4.5.2. Agile Logistics - - - A
A4.5.3. Two-Level Maintenance (2LM) - - - A
A4.5.4. Execution and Prioritization of Repair System (EXPRESS)
- - - A
A4.5.5. Readiness Based Leveling (RBL)
TR: AFMAN 23-110
- - - A
A4.5.6. Resource Management - - - B
A4.5.7. Air Force Government-Wide Purchase Card Program and Air Force Form 9
TR: AFI 67-117
- - - A
A4.5.8. Air Force Enhancement Program (AFREP)
TR: AFI 21-123
- - - A
A4.5.9. Financial Plan (FIN Plan) - - - A
A4.5.10. Appropriation (APPN) 3400 and 3080 Budgeting - - - A
A4.5.11. Budget Line 3010 - - - A
A4.5.12. Air Force Material Command (AFMC) Responsibilities
- - - A
A4.5.13. Developmental Test and Evaluation (DT&E) Operational Test and Evaluation (OT&E)
- - - A
A4.5.14. Defense Logistics Agency - - - A
A4.5.15. Special Experience Identifier (SEI)
TR: AFMAN 36-2108
- - - B
A4.5.16. Unit Manpower Document (UMD) and Unit Management Personnel Roster (UMPR)
- - - A
A4.5.17. Manning Standards, and Logistics Composite Model (LCOM)
TR: AFI 38-201, AFMAN 38-208
- - - A
A4.5.18. Technical Order Management - - - B
A4.5.19. Technical Order Distribution Office (TODO), Technical Order Distribution Account (TODA), Technical Order Distribution Control Activity (TODCA), Technical Order Review Board (TORB)
TR: TO 00-5-1, TO 00-5-2
- - - A
CDC 2AX7X TRAINING REQUIREMENTSSTS 2A6X6, October 2002
60Attachment 4
2. Core Tasks
3. Certification For OJT 4. Proficiency Codes Used To IndicateTraining/Information Provided
(See Attachment 1)1. Tasks, Knowledge And Technical References A B C D E A
3 LevelB
5 LevelC
7 Level5 7 Tng
StartTng
CompleteTraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A4.5.20. Air Force Technical Order Forms 22, 27, 110, 158 - - - A
A4.5.21. Automated Technical Order Management System (ATOMS)
TR: TO 00-5-2
- - - A
A4.5.22. Time Compliance Technical Orders (TCTO)
TR: TO 00-5-15
- - - A
A4.5.23. Centralized Technical Order Management Organization (CTOM)
TR: TO 00-5-1
- - - A
A4.5.24. Joint Computer –aided Acquisition and Logistic Support (JCALS)
- - - A
A4.5.25. Electronic Technical Orders - - - A
A4.5.26. Deficiency Reporting (Hardware and Software)Product Quality Deficiency Reporting System (PQDR)
TR: TO 00-35D-54
- - - B
A4.5.27. Reporting of Deficiency (ROD) - - - B
A4.5.28. Bad Actor Program
TR: TO 00-20-1, TO 00-35D-54
- - - A
A4.5.29. Technical Improvement Product Working Group (TIPWG), System Training Plan (STP), Program Management Review (PMR)
- - - A
A4.5.30. Corrosion Prevention Advisory Board (CPAB)
TR: AFI 21-105
- - - A
A4.6. COMPUTER APPLICATION
A4.6.1. Using Applications - - - B
A4.6.2. Form Flow - - - B
A4.6.3. Air Force Electronic Publishing Library (AFEPL) - - - B
A4.6.4. World Wide Web (www), Internet - - - B
A4.6.5. Local Area Networks (LAN) - - - B
B-2 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
61Attachment 5
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
ATTACHMENT 5
NOTE 1: In addition to attachment 2, the tasks and knowledge in attachment 6 will be performed by personnel assigned to maintain B-2 aircraft.
NOTE 2: Users are responsible for annotating training references to identify current references pending STS revision.
NOTE 3: Items marked in columns 2a or 2b marked with a (*R) are optional core tasks for ANG and AFRC.
NOTE 4: Address comments and recommended changes through Unit Training Managers to the MAJCOM Maintenance Training Manager @ HQ AMC/LGMMT, 402 SUnit 2A2, Scott AFB, IL 62225-5308; or call DSN 576-4787. MAJCOM Training and Functional Managers forward inputs to the AETC Training Manager, DSN 736-27
A5.1. AIRCRAFT FAMILIARIZATION
TR: 1B-2A-2-00GV-00-1, 1B-2A-2-01JG SERIES, 1B-2A-2-05GS-00-1, 1B-2A-2-05JG SERIES
A5.1.1. Engine Air Intake and Exhaust - - - -
A5.1.2. High Intensity Sound - - - -
A5.1.3. Turbine Plane of Rotation - - - -
A5.1.4. Antenna Radiation - - - -
A5.1.5. Ground Handling of Aircraft - - - -
A5.1.6. Hot Brakes - - - -
A5.1.7. Hardness Critical Procedures * - - - -
A5.1.8. Observable Critical Procedures - - - -
A5.1.9. Operate Crew Entry Door - - - -
A5.1.10. Operate Aft Equipment Bay Door - - - -
A5.1.11. Operate Weapons Bay Doors - - - -
A5.1.12. Open / Close Engine AMAD Bay Doors - - - -
A5.1.13. Open / Close Hyd / ECS Bay Doors - - - -
A5.1.14. Apply / Remove External Electrical Power * - - - -
A5.1.15. Apply / Remove Cooling Air * - - - -
A5.1.16. Apply / Remove External Bleed Air * - - - -
A5.2.17. Ensure Aircraft Safe for Maintenance * - - - -
A5.2. ENVIRONMENTAL CONTROL SYSTEM
TR: 1B-2A-2-21GS-00-1, 1B-2A-2-21JG SERIES, and 1B-2A-2-40JG SEIRES
A5.2.1. Operational Fundamentals - - - -
A5.2.2. Inspect - - - -
A5.2.3. Troubleshoot - - - -
A5.2.4. Component Location - - - -
A5.2.5. Perform ECS Operational Check * - - - -
A5.2.6. Perform ECS Leak Checks - - - -
A5.2.7. Perform ECS Power Up / Power Down * - - - -
A5.2.8. EGW Tank - - - -
A5.2.9. Display Cooling Fan Operational Check - - - -
B-2 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
62Attachment 5
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A5.2.10. Crew Compartment Pressure Test and Leak Check * - - - -
A5.2.11. ECS Ground Readiness Test
A5.2.12. ECS Special Maintenance Requirements
TR: 1B-2A-2-21GS-00-1
A5.2.12.1. ECS Valve Thawing - - - -
A5.2.12.2. AFT Avionics Cooling Fan Power ContactorMaintenance
- - - -
A5.2.12.3. Purge EGW Wetted Parts - - - -
A5.2.12.4. Outflow Valve Switch Adjustment - - - -
A5.2.13. Remove ECS Control Components
TR: 1B-2A-2-21JG-10-1
A5.2.13.1. System Controller - - - -
A5.2.13.2. ECS Control Panel - - - -
A5.2.14. Install ECS Control Components
TR: 1B-2A-2-21JG-10-1
A5.2.14.1. System Controller - - - -
A5.2.14.2. ECS Control Panel - - - -
A5.2.15. Remove ECS Recirculated Air Sub-System Components
TR: 1B-2A-2-21JG-20-1, -2
A5.2.15.1. Ground Air Inlets - - - -
A5.2.15.2. Ground Air Outlets - - - -
A5.2.15.3. Check Valves - - - -
A5.2.15.4. Avionics Cooling Fan - - - -
A5.2.15.5. Avionics Cooling Fan Assembly Filter - - - -
A5.2.15.6. Avionics Emergency Cooling Valve - - - -
A5.2.15.7. Avionics Pressure Rise Sensor - - - -
A5.2.15.8. Avionics Low Pressure Sensor - - - -
A5.2.15.9. Avionics Air Over temperature Sensor - - - -
A5.2.16. Install ECS Recirculated Air Sub-System Components
TR: 1B-2A-2-21JG-20-1, -2
A5.2.16.1. Ground Air Inlets - - - -
A5.2.16.2. Ground Air Outlets - - - -
A5.2.16.3. Check Valves - - - -
A5.2.16.4. Avionics Cooling Fan - - - -
A5.2.16.5. Avionics Cooling Fan Assembly Filter - - - -
A5.2.16.6. Avionics Emergency Cooling Valve - - - -
A5.2.16.7. Avionics Pressure Rise Sensor - - - -
B-2 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
63Attachment 5
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A5.2.16.8. Avionics Low Pressure Sensor - - - -
A5.2.16.9. Avionics Air Over temperature Sensor - - - -
A5.2.17. Remove ECS Pressurization Sub-System Components
TR: 1B-2A-2-21JG-30-1
A5.2.17.1. Crew Compartment Outflow Valves - - - -
A5.2.17.2. Crew Compartment Safety Valve - - - -
A5.2.17.3. Outflow Valve Control - - - -
A5.2.18. Install ECS Pressurization Components
TR: 1B-2A-2-21JG-30-1
A5.2.18.1. Crew Compartment Outflow Valves - - - -
A5.2.18.2. Crew Compartment Safety Valve - - - -
A5.2.18.3. Outflow Valve Control - - - -
A5.2.19. Remove ECS Warm Air Sub-System Components
TR: 1B-2A-2-21JG-40-1
A5.2.19.1. Check Valves - - - -
A5.2.19.2. Temp Control Valve - - - -
A5.2.19.3. Crossover Valve - - - -
A5.2.19.4. Precooler Assembly - - - -
A5.2.19.5. Temp Sensor - - - -
A5.2.19.6. Defog Diverter Valve - - - -
A5.2.19.7. Defog Heat Exchanger - - - -
A5.2.19.8. Defog Temp Control Valve - - - -
A5.2.20. Install ECS Warm Air Sub-System Components
TR: 1B-2A-2-21JG-40-1
A5.2.20.1. Check Valves - - - -
A5.2.20.2. Temp Control Valve - - - -
A5.2.20.3. Crossover Valve - - - -
A5.2.20.4. Precooler Assembly - - - -
A5.2.20.5. Temp Sensor - - - -
A5.2.20.6. Defog Diverter Valve - - - -
A5.2.20.7. Defog Heat Exchanger - - - -
A5.2.20.8. Defog Temp Control Valve - - - -
A5.2.21. Remove ECS Cooling Sub-System Components
TR: 1B-2A-2-21JG-50-1, -2
A5.2.21.1. Weapons Air Flow Control Valve - - - -
A5.2.21.2. Check Valves - - - -
A5.2.21.3. Conditioned Air Intercooler Assembly - - - -
B-2 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
64Attachment 5
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A5.2.21.4. Conditioned Air Cycle Pack - - - -
A5.2.21.5. Conditioned Air Cycle Machine - - - -
A5.2.21.6. Conditioned Air Water Extractor - - - -
A5.2.21.7. Conditioned Air Temp Control Valve - - - -
A5.2.21.8. Conditioned Air Condenser Relief Valve - - - -
A5.2.21.9. Conditioned Air Filter - - - -
A5.2.21.10. Conditioned Air Flow Control Valve - - - -
A5.2.21.11. Conditioned Air Flow Distribution Valve - - - -
A5.2.21.12. Conditioned Air Flow Sensor - - - -
A5.2.21.13. Foot Warmer Diffuser - - - -
A5.2.21.14. Equipment Air Cycle Pack - - - -
A5.2.21.15. Equipment Air Flow Control Valve - - - -
A5.2.21.16. Equipment Air Cycle Machine - - - -
A5.2.21.17. Equipment Air Bypass Valve - - - -
A5.2.21.18. Equipment Air Sink Heat Exchanger - - - -
A5.2.22. Install ECS Cooling Sub-System Components
TR: 1B-2A-2-22JG-50-1, -2
A5.2.22.1. Weapons Air Flow Control Valve - - - -
A5.2.22.2. Check Valves - - - -
A5.2.22.3. Conditioned Air Intercooler Assembly - - - -
A5.2.22.4 Conditioned Air Cycle Pack - - - -
A5.2.22.5. Conditioned Air Cycle Machine - - - -
A5.2.22.6. Conditioned Air Water Extractor - - - -
A5.2.22.7. Conditioned Air Temp Control Valve - - - -
A5.2.22.8. Conditioned Air Condenser Relief Valve - - - -
A5.2.22.9. Conditioned Air Filter - - - -
A5.2.22.10. Conditioned Air Flow Control Valve - - - -
A5.2.22.11. Conditioned Air Flow Distribution Valve - - - -
A5.2.22.12. Conditioned Air Flow Sensor - - - -
A5.2.22.13. Foot Warmer Diffuser - - - -
A5.2.22.14. Equipment Air Cycle Pack - - - -
A5.2.22.15. Equipment Air Flow Control Valve - - - -
A5.2.22.16. Equipment Air Cycle Machine - - - -
A5.2.22.17. Equipment Air Bypass Valve - - - -
A5.2.22.18. Equipment Air Sink Heat Exchanger - - - -
A5.2.23. ECS Liquid Cooling Checks
TR:1B-2A-2-21JG-80-1, -2, -3, -4
A5.2.23.1. LCS Fluid Replacement and Leak Check - - - -
B-2 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
65Attachment 5
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A5.2.23.2. LCS Fluid Sampling - - - -
A5.2.23.3. LCS Fluid Air Entrapment Check - - - -
A5.2.23.4. EGW Fluid Replacement and Leak Check - - - -
A5.2.23.5. EGW Fluid Sampling - - - -
A5.2.23.6. Sink Heat Exchanger and Air Cycle Pack EGW Fluid Replacement and Leak Check
- - - -
A5.2.23.7. EWG Fluid Air Entrapment Check - - - -
A5.2.23.8. DMS Fluid Replacement and Leak Check - - - -
A5.2.23.9. DMS Fluid Sampling - - - -
A5.2.23.10. DMS Fluid Air Entrapment Check - - - -
A5.2.24. Remove ECS Liquid Cooling Sub-System Components
TR:1B-2A-2-21JG-80-1, -2, -3, -4
A5.2.24.1. LCS Pump Package - - - -
A5.2.24.2. LCS Heat Exchanger - - - -
A5.2.24.3. LCS Coolant Pressure Relief Valve - - - -
A5.2.24.4. LCS Overboard Pressure Relief Valve - - - -
A5.2.24.5. LCS Coolant Overflow Container - - - -
A5.2.24.6. EGW Pump Package - - - -
A5.2.24.7. FWD EGW Heat Exchanger - - - -
A5.2.24.8. CTB EGW Heat Exchanger - - - -
A5.2.24.9. Aft EGW Heat Exchanger - - - -
A5.2.24.10. DMS Pump Package - - - -
A5.2.24.11. DMS Heat Exchange - - - -
A5.2.25. Install ECS Liquid Cooling Sub-System Components
TR:1B-2A-2-21JG-80-1, -2, -3, -4
A5.2.25.1. LCS Pump Package - - - -
A5.2.25.2. LCS Heat Exchanger - - - -
A5.2.25.3. LCS Coolant Pressure Relief Valve - - - -
A5.2.25.4. LCS Overboard Pressure Relief Valve - - - -
A5.2.25.5. LCS Coolant Overflow Container - - - -
A5.2.25.6. EGW Pump Package - - - -
A5.2.25.7. FWD EGW Heat Exchanger - - - -
A5.2.25.8. CTB EGW Heat Exchanger - - - -
A5.2.25.9. Aft EGW Heat Exchanger - - - -
A5.2.25.10. DMS Pump Package - - - -
A5.2.25.11. DMS Heat Exchange - - - -
A5.2.26. Repair / Overhaul / Bench Check Components
TR:8C, 8D, and 15A SERIES
B-2 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
66Attachment 5
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A5.2.26.1. ECS Control Panel - - - -
A5.2.26.2. Air Conditioning Air Cycle Pack - - - -
A5.2.26.3. Liquid Media Cooling Switch Panels - - - -
A5.2.26.4. Conditioned Air Filter - - - -
A5.2.26.5. Desiccant Filter - - - -
A5.2.26.6. Conditioned Air Exhaust Port - - - -
A5.2.26.7. Emergency Cooling Air Valve - - - -
A5.2.26.8. Outflow Valve - - - -
A5.3. ELECTRICAL POWER SYSTEM
TR: 1B-2A-2-24GS-00-1, 1B-2A-2-24JG SERIES
A5.3.1. Operational Fundamentals - - - -
A5.3.2. AC Operational Check - - - -
A5.3.3. DC Operational Check Inspect - - - -
A5.3.4. External Power Operational Check - - - -
A5.3.5. Chip Detector Checkout - - - -
A5.3.7. Inspect - - - -
A5.3.8. Troubleshoot - - - -
A5.3.9. Component Location - - - -
A5.3.10. Electrical System Special MaintenanceRequirements
TR:1B-2A-2-24GS-00-1
A5.3.10.1. Circuit Breaker Panel Maintenance * - - - -
A5.3.10.2. AC CB Panel Differential Protection Current Transformer Assembly (DPCTA) Maintenance
- - - -
A5.3.10.3. Diode Panel Maintenance - - - -
A5.3.10.4. Power Contactor Maintenance - - - -
A5.3.10.5. Bus Diode Maintenance - - - -
A5.3.10.6. MUX Bus Coupler Maintenance - - - -
A5.3.10.7. Converter Regulator (CR) Support Assembly Maintenance
- - - -
A5.3.11. Remove AC System Components
TR:1B-2A-2-24JG-20-1
A5.3.11.1. IDG - - - -
A5.3.11.2. Generator Control Unit - - - -
A5.3.11.3. Line Contactor - - - -
A5.3.11.4. Bus Contactor - - - -
A5.3.11.5. Current Control Transformer Assembly (CCTA) - - - -
A5.3.11.6. Differential Protection Current Transformer Assembly (DPCTA)
- - - -
B-2 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
67Attachment 5
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A5.3.11.7. IDG Chip Detector - - - -
A5.3.11.8. Bus Control Unit - - - -
A5.3.12. Install AC System Components
TR:1B-2A-2-24JG-20-1
A5.3.12.1. IDG - - - -
A5.3.12.2. Generator Control Unit - - - -
A5.3.12.3. Line Contactor - - - -
A5.3.12.4. Bus Contactor - - - -
A5.3.12.5. Current Control Transformer Assembly (CCTA) - - - -
A5.3.12.6. Differential Protection Current TransformerAssembly (DPCTA)
- - - -
A5.3.12.7. IDG Chip Detector - - - -
A5.3.12.8. Bus Control Unit - - - -
A5.3.13. Remove DC System Components
TR:1B-2A-2-24JG-30-1
A5.3.13.1. Transformer Rectifier - - - -
A5.3.13.2. Battery - - - -
A5.3.13.3. Battery Charger - - - -
A5.3.13.4. Battery Circuit Breaker - - - -
A5.3.13.5. DC Bus Fuse - - - -
A5.3.13.6. APU Generator Control Unit - - - -
A5.3.13.7. APU Permanent Magnet Generator - - - -
A5.3.13.8. Converter Regulator - - - -
A5.3.13.9. AMAD Permanent Magnet Generator - - - -
A5.3.14. Install DC System Components
TR:1B-2A-2-24JG-30-1
A5.3.14.1. Transformer Rectifier - - - -
A5.3.14.2. Battery - - - -
A5.3.14.3. Battery Charger - - - -
A5.3.14.4. Battery Circuit Breaker - - - -
A5.3.14.5. DC Bus Fuse - - - -
A5.3.14.6. APU Generator Control Unit - - - -
A5.3.14.7. APU Permanent Magnet Generator - - - -
A5.3.14.8. Converter Regulator - - - -
A5.3.14.9. AMAD Permanent Magnet Generator - - - -
A5.3.15. Remove External Power System Components
TR:1B-2A-2-24JG-40-1
A5.3.15.1. External Power DPCTA - - - -
B-2 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
68Attachment 5
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A5.3.15.2. External Power Contactor - - - -
A5.3.15.3. External Power Receptacle - - - -
A5.3.16. Install External Power System Components
TR:1B-2A-2-24JG-40-1
A5.3.16.1. External Power DPCTA - - - -
A5.3.16.2. External Power Contactor - - - -
A5.3.16.3. External Power Receptacle - - - -
A5.3.17. Remove Electrical Load Distribution SystemComponents
TR:1B-2A-2-24JG-50-1
A5.3.17.1. DC Bus Tie Relay - - - -
A5.3.17.2. Electrical Power Control Panel - - - -
A5.3.17.3. Ground Power Control Panel - - - -
A5.3.17.4. Air Undercool Sensor - - - -
A5.3.17.5. Undercool Warning Bell - - - -
A5.3.17.6. Power Control Unit - - - -
A5.3.17.7. Processor Control Panel - - - -
A5.3.18. Install Electrical Load Distribution System Components
TR:1B-2A-2-24JG-50-1
A5.3.18.1. DC Bus Tie Relay - - - -
A5.3.18.2. Electrical Power Control Panel - - - -
A5.3.18.3. Ground Power Control Panel - - - -
A5.3.18.4. Air Undercool Sensor - - - -
A5.3.18.5. Undercool Warning Bell - - - -
A5.3.18.6. Power Control Unit - - - -
A5.3.18.7. Processor Control Panel - - - -
A5.3.19. Repair / Overhaul / Bench Check Components
TR:8C, and 8D SERIES
A5.3.19.1. Electrical Power Control Panel - - - -
A5.3.19.2. Ground Power Control Panel - - - -
A5.3.19.3. Transformer Rectifier - - - -
A5.3.19.4. Diode Panel - - - -
A5.3.19.5. Battery - - - -
A5.4. Repair / Overhaul / Bench Check Equipment/Furnishings System Components
TR: 8D, and 13A SERIES
A5.4.1. Crew Entry Hatch Control Panel - - - -
A5.4.2. Sustenance Container - - - -
B-2 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
69Attachment 5
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A5.5. FIRE PROTECTION SYSTEM
TR:1B-2A-2-26GS-00-1, 1B-2A-2-26JG SERIES
A5.5.1. Operational Fundamental - - - -
A5.5.2. Fire Protection Operational Checkout - - - -
A5.5.3. Extinguishing Operational Checkout * - - - -
A5.5.4. Inspect - - - -
A5.5.5. Troubleshoot - - - -
A5.5.6. Component Location - - - -
A5.5.7. Fire Protection Special Maintenance Requirements
TR:1B-2A-2-26GS-00-1
A5.5.7.1. Fire and Overheat Connector Removal / Installation - - - -
A5.5.8. Remove Fire Protection System Components
TR:1B-2A-2-26JG-10-1
A5.5.8.1. Fire Master Switch - - - -
A5.5.8.2. Fire Warning Leak Detection Terminal Protection Device
- - - -
A5.5.8.3. Leak Detector Controller - - - -
A5.5.8.4. Fire and Aft Tailpipe O/H Sensor - - - -
A5.5.8.5. Leak Detector - - - -
A5.5.9. Install Fire Protection System Components
TR:1B-2A-2-26JG-10-1
A5.5.9.1. Fire Master Switch - - - -
A5.5.9.2. Fire Warning Leak Detection Terminal Protection Device
- - - -
A5.5.9.3. Leak Detector Controller - - - -
A5.5.9.4. Fire and Aft Tailpipe O/H Sensor - - - -
A5.5.9.5. Leak Detector - - - -
A5.5.10. Remove Fire Extinguishing System Components
TR:1B-2A-2-26JG-20-1, -2, -3
A5.5.10.1. Fire Extinguishing Bottle - - - -
A5.5.10.2. Engine Fire Extinguishing Head and BottleDischargeCartridge
- - - -
A5.5.10.3. Agent Discharge Switch - - - -
A5.5.10.4. Ground Alert Horn - - - -
A5.5.10.5. ENG/APU Fire Switch - - - -
A5.5.10.6. Initiator - - - -
A5.5.10.7. Fire Extinguishing Relay Panel - - - -
A5.5.10.8. APU Discharge Head and APU Discharge Cartridge - - - -
A5.5.10.9 Butterfly Valve - - - -
B-2 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
70Attachment 5
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A5.5.11. Install Fire Extinguishing System Components
TR:1B-2A-2-26JG-20-1, -2, -3
A5.5.11.1. Fire Extinguishing Bottle - - - -
A5.5.11.2. Engine Fire Extinguishing Head and Bottle Discharge Cartridge
- - - -
A5.5.11.3. Agent Discharge Switch - - - -
A5.5.11.4. Ground Alert Horn - - - -
A5.5.11.5. ENG/APU Fire Switch - - - -
A5.5.11.6. Initiator - - - -
A5.5.11.7. Fire Extinguishing Relay Panel - - - -
A5.5.11.8. APU Discharge Head and APU Discharge Cartridge - - - -
A5.5.11.9. Butterfly Valve - - - -
A5.5.12. Repair / Overhaul / Bench Check Components
TR:8D, and 15A SERIES
A5.5.12.1. Fire Extinguisher Relay Panel - - - -
A5.5.12.2. Terminal Protection Device Housing Assembly - - - -
A5.6. Repair / Overhaul / Bench Check Flight Control System Components
TR:8D SERIES
A5.6.1. Flight Control Panel - - - -
A5.7. ICE AND RAIN PROTECTION SYSTEM
TR:1B-2A-2-30GS-00-1, 1B-2A-2-30JG SERIES
A5.7.1. Operational Fundamentals - - - -
A5.7.2. Windshield AI/RR Operational Checkout - - - -
A5.7.3. Windshield AI/RR Leak Check - - - -
A5.7.4. Inspect - - - -
A5.7.5. Troubleshoot - - - -
A5.7.6. Component Location - - - -
A5.7.7. Remove Ice and Rain Protection System Components
TR:1B-2A-2-30JG-40-1
A5.7.7.1. Air Pressure Regulator Shutoff Valve - - - -
A5.7.7.2. Air Overtemp Shutoff Valve - - - -
A5.7.7.3. Nozzle - - - -
A5.7.7.4. Air Temp Sensor - - - -
A5.7.8. Install Ice and Rain Protection System Components
TR:1B-2A-2-30JG-40-1
A5.7.8.1. Air Pressure Regulator Shutoff Valve - - - -
A5.7.8.2. Air Overtemp Shutoff Valve - - - -
B-2 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
71Attachment 5
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A5.7.8.3. Nozzle - - - -
A5.7.8.4. Air Temp Sensor - - - -
A5.8. CONTROL AND DISPLAY SYSTEM
TR: 1B-2A-2-31JG-10-1
A5.8.1. Remove/Install Disk Cartridge * - - - -
A5.9. LANDING GEAR SYSTEM
TR:1B-2A-2-32GS-00-1
A5.9.1. Operational Fundamentals - - - -
A5.9.2. Inspect - - - -
A5.9.3. Troubleshoot - - - -
A5.9.4. Component Location - - - -
A5.9.5. Remove Landing Gear System Components
TR: 1B-2A-2-32JG SERIES
A5.9.5.1. Landing Gear Control Assembly - - - -
A5.9.5.2. Proximity Sensors - - - -
A5.9.5.3. Proximity Sensor Logic Unit - - - -
A5.9.6. Install Landing Gear System Components
TR: 1B-2A-2-32JG SERIES
A5.9.6.1. Landing Gear Control Assembly - - - -
A5.9.6.2. Proximity Sensors - - - -
A5.9.6.3. Proximity Sensor Logic Unit - - - -
A5.9.7. Repair / Overhaul / Bench Check Landing Gear System Components
TR:8C, 8D, 9H, and 16W SERIES
A5.9.7.1. Landing Gear Control Panel - - - -
A5.9.7.2. Emergency Landing Gear Control Panel - - - -
A5.9.7.3. Door Lock Selector Valve - - - -
A5.9.7.4. Isolation Valve Selector - - - -
A5.9.7.5. Accumulator Service Crew Entry/Brake Panel - - - -
A5.10. LIGHTING SYSTEM
TR:1B-2-33GS-00-1, 1B-2A-2-33JG SERIES
A5.10.1. Operational Fundamentals - - - -
A5.10.2. Crew Compartment Lighting Operational Checkout - - - -
A5.10.3. Service Lighting Operational Checkouts - - - -
A5.10.4. Exterior Lighting Operational Checkout - - - -
A5.10.5. Emergency Lighting Operational Checkout - - - -
A5.10.6. Inspect - - - -
A5.10.7. Troubleshoot - - - -
B-2 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
72Attachment 5
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A5.10.8. Component Location - - - -
A5.10.9. Remove Crew Compartment Lighting Components
TR:1B-2A-2-33JG-10-1, -2
A5.10.9.1. Warning Caution Advisory Panel - - - -
A5.10.9.2. Master Warning/Master Caution Switch - - - -
A5.10.9.3. Floodlights - - - -
A5.10.9.4. Utility Lights - - - -
A5.10.9.5. Dimmers - - - -
A5.10.10. Install Crew Compartment Lighting Components
TR:1B-2A-2-33JG-10-1, -2
A5.10.10.1. Warning Caution Advisory Panel - - - -
A5.10.10.2. Master Warning/Master Caution Switch - - - -
A5.10.10.3. Floodlights - - - -
A5.10.10.4. Utility Lights - - - -
A5.10.10.5. Dimmers - - - -
A5.10.10.6. Lighting Control Panels - - - -
A5.10.10.7. Entry Light Switch - - - -
A5.10.10.8. Time Delay Relay Panel - - - -
A5.10.10.9. Standby Instrument Transfer Relay Panel - - - -
A5.10.11. Remove Service Lighting Components
TR: 1B-2A-2-33JG-30-1
A5.10.11.1. Weapons Bay Lights - - - -
A5.10.11.2. Main/Nose Wheel Well Lights - - - -
A5.10.11.3. Aft Equipment Bay Light - - - -
A5.10.11.4. Right Radar Bay Light - - - -
A5.10.12. Install Service Lighting Components
TR: 1B-2A-2-33JG-30-1
A5.10.12.1. Weapons Bay Lights - - - -
A5.10.12.2. Main/Nose Wheel Well Lights - - - -
A5.10.12.3. Aft Equipment Bay Light - - - -
A5.10.12.4. Right Radar Bay Light - - - -
A5.10.13. Remove Exterior Lighting Components
TR:1B-2A-2-33JG-40-1
A5.10.13.1. Landing-Taxi Light - - - -
A5.10.13.2. A/R Lead-In Floodlight - - - -
A5.10.13.3. Inlet Floodlight - - - -
A5.10.13.4. Nacelle Floodlight - - - -
A5.10.13.6. Wing Tip Light - - - -
B-2 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
73Attachment 5
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A5.10.13.7. Wing Tip Power Supply - - - -
A5.10.14. Install Exterior Lighting Components
TR:1B-2A-2-33JG-40-1
A5.10.14.1. Landing-Taxi Light - - - -
A5.10.14.2. A/R Lead-In Floodlight - - - -
A5.10.14.3. Inlet Floodlight - - - -
A5.10.14.4. Nacelle Floodlight - - - -
A5.10.14.5. Dimmer - - - -
A5.10.14.6. Wing Tip Light - - - -
A5.10.14.7. Wing Tip Power Supply - - - -
A5.10.15. Remove/ Install Emergency Lighting Components
TR:1B-2A-2-33JG-50-1
A5.10.15.1. Emergency Light - - - -
A5.10.16. Repair / Overhaul / Bench Check Components
TR:8A SERIES
A5.10.16.1. Power Supply Wing Tip Lighting - - - -
A5.10.16.2. Light Assembly A/C Position and Strobe - - - -
A5.10.16.3. Pilots Lighting Control Panel - - - -
A5.10.16.4. Overhead Lighting Control Panel - - - -
A5.11. OXYGEN SYSTEM
TR:1B-2A-2-35GS-00-1, 1B-2A-2-35JG, and 1B-2A-2-40JG SERIES
A5.11.1. Operational Fundamentals - - - -
A5.11.2. Primary Oxygen Operational Checkout * - - - -
A5.11.3. Back-up Oxygen System Operational Checkout - - - -
A5.11.4. Oxygen System Purge - - - -
A5.11.5. BOS Cylinder Assembly Depressurization - - - -
A5.11.6. Oxygen System Selective GRT - - - -
A5.11.7. Inspect - - - -
A5.11.8. Troubleshoot - - - -
A5.11.9. Component Location - - - -
A5.11.10. Oxygen System Special Maintenance Requirements
TR:1B-2A-2-35GS-00-1
A5.11.10.1. EOS Cylinder Assembly Servicing (OFF AIRCRAFT) - - - -
A5.11.11. Remove Oxygen System Components
TR:1B-2A-2-35JG-10-1, -2
A5.11.11.1. Oxygen Concentrator - - - -
A5.11.11.2. Inlet Filter - - - -
B-2 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
74Attachment 5
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A5.11.11.3. Outlet Filter - - - -
A5.11.11.4. Electronic Control Unit - - - -
A5.11.11.5. Composition Monitor - - - -
A5.11.11.6. OGADS Heater Control Unit - - - -
A5.11.11.7. OGADS Sample Filter - - - -
A5.11.11.8. Oxygen Breathing Regulator - - - -
A5.11.11.9. Oxygen Control Panel - - - -
A5.11.11.10 BOS Cylinder Assembly - - - -
A5.11.11.11. BOS Release Valve - - - -
A5.11.11.12 .EOS Cylinder - - - -
A5.11.12. Install Oxygen System Components
TR:1B-2A-2-35JG-10-1, -2
A5.11.12.1. Oxygen Concentrator - - - -
A5.11.12.2. Inlet Filter - - - -
A5.11.12.3 Outlet Filter - - - -
A5.11.12.4. Electronic Control Unit - - - -
A5.11.12.5. Composition Monitor - - - -
A5.11.12.6. OGADS Heater Control Unit - - - -
A5.11.12.7. OGADS Sample Filter - - - -
A5.11.12.8. Oxygen Breathing Regulator - - - -
A5.11.12.9. Oxygen Control Panel - - - -
A5.11.12.10. BOS Cylinder Assembly - - - -
A5.11.12.11. BOS Release Valve - - - -
A5.11.12.12. EOS Cylinder - - - -
A5.11.13. Repair / Overhaul / Bench Check Components
TR: 15X SERIES
A5.11.13.1. Oxygen System Control Panel - - - -
A5.12. PNEUMATIC SYSTEM
TR:1B-2A-2-36GS-00-1, 1B-2A-2-36JG SERIES
A5.12.1. Operational Fundamentals - - - -
A5.12.2. Bleed Air Control Panel Checkout - - - -
A5.12.3. Inspect - - - -
A5.12.4. Troubleshoot - - - -
A5.12.5. Component Location - - - -
A5.12.6. Pneumatic System Special Maintenance Requirements
TR:1B-2A-2-36GS-00-1
A5.12.6.1. 5TH AND 9TH Primary Pressure Regulator Switch Checkout
- - - -
B-2 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
75Attachment 5
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A5.12.7. Remove Pneumatic System Components
TR:1B-2A-2-36JG-10-1, 36JG-20-1
A5.12.7.1. 5TH Primary Pressure Regulator Valve - - - -
A5.12.7.2. Bleed Air Check Valve - - - -
A5.12.7.3. Isolation Valve - - - -
A5.12.7.4. Ejector Valve - - - -
A5.12.7.5. Bleed Air Control Panel - - - -
A5.12.7.6. 9th Primary Pressure Regulator - - - -
A5.12.8.7. Secondary Pressure Regulator - - - -
A5.12.8.8. Bleed Air Pressure Sensor - - - -
A5.12.9. Repair / Overhaul / Bench Check Components
TR:8D, and 9P SERIES
A5.12.9.1. Bleed Air Control Panel - - - -
A5.12.9.2. Valves - - - -
A5.13. Electrical/Electronic and Multipurpose System Components
TR: 1B-2A-A-39GS-00-1, and 39JG SERIES
A5.13.1. Operational Fundamentals - - - -
A5.13.2. Inspect - - - -
A5.13.3. Troubleshoot - - - -
A5.13.4. Component Location - - - -
A5.13.5. Remove Electrical/Electronic Panels
TR:1B-2A-2-39JG-40-1, 40-2
A5.13.5.1. Relay Panels - - - -
A5.13.5.2. APU/Engine Start Control Panel - - - -
A5.13.5.3. Alert Switch Control Panel - - - -
A5.13.5.4. Brake/Landing Light Control Panel - - - -
A5.13.5.5. Diode Panel - - - -
A5.13.5.6. Relay Power Panel - - - -
A5.13.6. Install Electrical/Electronic Panels
TR:1B-2A-2-39JG-40-1, 40-2
A5.13.6.1. Relay Panels - - - -
A5.13.6.2. APU/Engine Start Control Panel - - - -
A5.13.6.3. Alert Switch Control Panel - - - -
A5.13.6.4. Alert Switch Control Panel - - - -
A5.13.6.5. Brake/Landing Light Control Panel - - - -
A5.13.6.6. Diode Panel - - - -
A5.13.6.7. Relay Power Panel - - - -
B-2 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
76Attachment 5
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A5.13.7. Repair / Overhaul / Bench Check Components
TR:8A, 8D, and 8R SERIES
A5.13.7.1. Relay Panels - - - -
A5.13.7.2. Alert Switch Control Panel - - - -
A5.13.7.3. APU/Engine Start Control Panel - - - -
A5.13.7.4. Brake/Landing Light Control Panel - - - -
A5.13.7.5. Diode Panel - - - -
A5.13.7.6. Relay Power Panel - - - -
A5.14. Repair / Overhaul / Bench Check Auxiliary Power System Components
TR:8D, and 9P SERIES
A5.14.1. Check Valves - - - -
A5.14.2. APU Maintenance Panel - - - -
A5.14.3. Alert Arm Control Panel - - - -
A5.15. Repair / Overhaul / Bench Check Power Plant System Components
TR: 8D SERIES
A5.15.1. Engine Auxiliary Inlet Doors Control Panel - - - -
A5.16. Repair / Overhaul / Bench Check Engine AirSystem Components
TR: 15E SERIES
A5.16.1. Ice Detector - - - -
A5.17. Repair / Overhaul / Bench Check Engine ControlSystem Components
TR: 5E, and 8C SERIES
A5.17.1. Throttle Quadrant/Grips - - - -
A5.17.2. Alternate Throttle Panel - - - -
A5.18. Repair / Overhaul / Bench Check Accessory GearboxSystem Components
TR: 5L, and 8D SERIES
A5.18.1. AMAD Oil Readout Panel - - - -
A5.18.2. Accessory Drive Control Panel - - - -
A5.18.3. Chip Detector Power Module - - - -
A5.18.4. Fan/Duct Assembly - - - -
A5.19. Repair / Overhaul / Bench Check Crew Escape andSafety System Components
TR: 8D SERIES
A5.19.1. Seat Adjustment Control Panel Assembly - - - -
A5.20. Center Wing Skin/Panels
TR:1B-2A-2-53JG-30-2
B-2 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
77Attachment 5
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A5.20.1. Remove/Install Crew Station Liners - - - -
A5.21. Power supplies
TR:Applicable T. O.
A5.21.1. Operate DC power supply - - - -
A5.21.2. Operate AC power supply - - - -
C-5 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
78Attachment 6
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
ATTACHMENT 6
NOTE 1: In addition to attachment 2, the tasks and knowledge in attachment 6 will be performed by personnel assigned to maintain C-5 aircraft.
NOTE 2: Users are responsible for annotating training references to identify current references pending STS revision.
NOTE 3: Items marked in columns 2a or 2b marked with a (*R) are optional core tasks for ANG and AFRC.
NOTE 4: Address comments and recommended changes through Unit Training Managers to the MAJCOM Maintenance Training Manager @ HQ AMC/LGMMT,402 Scott Drive Unit 2A2, Scott AFB, IL 62225-5308; or call DSN 576-4787. MAJCOM Training and Functional Managers forward inputs to the AETC TrainingManager, DSN 736-2772.
A6.1 AC POWER SYSTEM TR:
A6.1.1. Operational fundamentals - - - -
A6.1.2. Operational check system
A6.1.2.1 Main AC generator system - - - -
A6.1.2.2 Emergency generator system - - - -
A6.1.2.3. APU - - - -
A6.1.2.4 60 Hertz system - - - -
A6.1.3. Troubleshoot system
A6.1.3.1. Main AC power generator - - - -
A6.1.3.2. Emergency generator system - - - -
A6.1.3.3. APU - - - -
A6.1.4. Inspect System components
A6.1.4.1. AC Power Generator * - - - -
A6.1.4.2. Emergency Generator * - - - -
A6.1.4.3. APU * - - - -
A6.1.4.4. 60 Hertz * - - - -
A6.1.5. Remove components
A6.1.5.1. CSD - - - -
A6.1.5.2. Generator - - - -
A6.1.5.3. Emergency Generator - - - -
A6.1.5.4. GCU - - - -
A6.1.5.5. Bus Protection Panels - - - -
A6.1.5.6. Load Controllers - - - -
A6.1.5.7. Bus Tie/Generator Line Contactors - - - -
A6.1.5.8. Power Contactors - - - -
A6.1.5.9. Current transformer - - - -
A6.1.5.10. Power Transfer Relays - - - -
A6.1.6. Repair components
A6.1.6.1. CSD - - - -
A6.1.6.2. AC Generator - - - -
A6.1.6.3. Emergency Generator - - - -
A6.1.6.4. GCU - - - -
C-5 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
79Attachment 6
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A6.1.6.5. Bus Protection Panels - - - -
A6.1.6.6. Load Controllers - - - -
A6.1.6.7. Bus Tie/Generator Line Contactors - - - -
A6.1.6.8. Power Contactors - - - -
A6.1.6.9. Power Transfer Relays - - - -
A6.1.7. Install components
A6.1.7.1. CSD - - - -
A6.1.7.2. AC Generator - - - -
A6.1.7.3. Emergency Generator - - - -
A6.1.7.4. GCU - - - -
A6.1.7.5. Bus Protection Panels - - - -
A6.1.7.6. Load Controllers - - - -
A6.1.7.7. Bus Tie/Generator Line Contactors - - - -
A6.1.7.8. Power Contactors - - - -
A6.1.7.9. Current transformer - - - -
A6.1.7.10. Power Transfer Relays - - - -
A6.1.8. Bench check
A6.1.8.1. CSD - - - -
A6.1.8.2. AC Generator - - - -
A6.1.8.3. Emergency Generator - - - -
A6.1.8.4. GCU - - - -
A6.1.8.5. Bus Protection Panels - - - -
A6.1.8.6. Load Controllers - - - -
A6.1.8.7. Bus Tie/Generator Line Contactors - - - -
A6.1.8.8. Power Contactors - - - -
A6.1.8.9. Power Transfer Relays - - - -
A6.2. DC POWER SYSTEM TR:
A6.2.1. Operational fundamentals - - - -
A6.2.2. Operational Check System - - - -
A6.2.3. Troubleshoot System * - - - -
A6.2.4. Inspect System Components * - - - -
A6.2.5. Remove components
A6.2.5.1. Battery - - - -
A6.2.5.2. Transformer rectifier - - - -
A6.2.5.3. Gauges - - - -
A6.2.5.4. Reverse current relays - - - -
A6.2.5.5. Bus relays - - - -
A6.2.5.6. Panels - - - -
C-5 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
80Attachment 6
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A6.2.6. Repair components
A6.2.6.1. Transformer rectifier - - - -
A6.2.6.2. Bus relays - - - -
A6.2.6.3. Panels - - - -
A6.2.6.4. Reverse current relays - - - -
A6.2.7. Install components
A6.2.7.1. Battery - - - -
A6.2.7.2. Transformer rectifier - - - -
A6.2.7.3. Gauges - - - -
A6.2.7.4. Reverse current relays - - - -
A6.2.7.5. Bus relays - - - -
A6.2.7.6. Panels - - - -
A6.2.8. Bench check
A6.2.8.1. Transformer rectifier - - - -
A6.2.8.2. Reverse current relays - - - -
A6.2.8.3. Bus relays - - - -
A6.2.8.4. Panels - - - -
A6.3. EXTERNAL POWER SYSTEM TR:
A6.3.1. Operational fundamentals - - - -
A6.3.2. Operational Check System - - - -
A6.3.3. Troubleshoot System * - - - -
A6.3.4. Inspect System Components * - - - -
A6.3.5. Remove components
A6.3.5.1. Line contactors - - - -
A6.3.5.2. Ext power receptacle - - - -
A6.3.5.3. Current transformer - - - -
A6.3.6. Install components
A6.3.6.1. Line contactors - - - -
A6.3.6.2. Ext power receptacle - - - -
A6.3.6.3. Current transformer - - - -
A6.3.7. Bench Ck/Repair Line Contactors - - - -
A6.4. APU power system
A6.4.1. Operational fundamentals - - - -
A6.4.2. Operational Check System - - - -
A6.4.3. Service Auxiliary Power Unit (APU) with oil
TR: TO 1C-5A-2-1
- - - -
A6.4.4. Troubleshoot System - - - -
A6.4.5. Inspect System Components - - - -
C-5 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
81Attachment 6
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A6.4.6. Remove APU GCU - - - -
A6.4.7. Install APU GCU - - - -
A6.4.8. Bench Ck/Repair APU GCU - - - -
A6.5. LIGHTING SYSTEM TR:
A6.5.1. Operational fundamentals - - - -
A6.5.2. Operational Check System
A6.5.2.1. Interior - - - -
A6.5.2.2. Exterior - - - -
A6.5.2.3. Emergency - - - -
A6.5.3. Troubleshoot system
A6.5.3.1. Interior - - - -
A6.5.3.2. Exterior - - - -
A6.5.3.3. Emergency - - - -
A6.5.4. Inspect System Components
A6.5.4.1. Interior - - - -
A6.5.4.2. Exterior - - - -
A6.5.4.3. Emergency - - - -
A6.5.5. Remove Components
A6.5.5.1. Strobe light - - - -
A6.5.5.2. Navigation/formation - - - -
A6.5.5.3. Anti-collision - - - -
A6.5.5.4. Retractable landing light - - - -
A6.5.5.5. Taxi light - - - -
A6.5.5.6. Map/chart holder - - - -
A6.5.5.7. Emergency exit light - - - -
A6.5.5.8. Controllers - - - -
A6.5.5.9. Transformers - - - -
A6.5.5.10. Leading edge light - - - -
A6.5.5.11. Advisory lights - - - -
A6.5.5.12. Flood lights - - - -
A6.5.5.13. Power supply - - - -
A6.5.5.14. Light cards - - - -
A6.5.5.15. Relays - - - -
A6.5.5.16. IFR/Slipway light - - - -
A6.5.6. Repair Components
A6.5.6.1. Strobe light - - - -
A6.5.6.2. Navigation/formation - - - -
A6.5.6.3. Anti-collision - - - -
C-5 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
82Attachment 6
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A6.5.6.4. Retractable landing light - - - -
A6.5.6.5. Taxi light - - - -
A6.5.6.6. Map/chart holder - - - -
A6.5.6.7. Emergency exit light - - - -
A6.5.6.8. Leading edge light - - - -
A6.5.6.9. Advisory lights - - - -
A6.5.6.10. Power supply - - - -
A6.5.7. Install Components
A6.5.7.1. Strobe light - - - -
A6.5.7.2. Navigation/formation - - - -
A6.5.7.3. Anti-collision - - - -
A6.5.7.4. Retractable landing light - - - -
A6.5.7.5. Taxi light - - - -
A6.5.7.6. Map/chart holder - - - -
A6.5.7.7. Emergency exit light - - - -
A6.5.7.8. Controllers - - - -
A6.5.7.9. Transformers - - - -
A6.5.7.10. Leading edge light - - - -
A6.5.7.11. Advisory lights - - - -
A6.5.7.12. Flood lights - - - -
A6.5.7.13. Power supply - - - -
A6.5.7.14. Light cards - - - -
A6.5.7.15. Relays - - - -
A6.5.7.16. IFR/Slipway light - - - -
A6.5.8. Bench check
A6.5.8.1. Strobe light - - - -
A6.5.8.2. Navigation/formation - - - -
A6.5.8.3. Anti-collision - - - -
A6.5.8.4. 125Retractable landing light - - - -
A6.5.8.5. Taxi light - - - -
A6.5.8.6. Map/chart holder - - - -
A6.5.8.7. Emergency exit light - - - -
A6.5.8.8. Leading edge light - - - -
A6.5.8.9. Advisory lights - - - -
A6.5.8.10. Power supply - - - -
A6.6. LANDING GEAR/KNEELING SYSTEM
TR:
A6.6.1. Operational fundamentals - - - -
C-5 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
83Attachment 6
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A6.6.2. Troubleshoot System * - - - -
A6.6.3. Inspect System Components * - - - -
A6.6.4. Remove components
A6.6.4.1. Control handle - - - -
A6.6.4.2. Sequence panel - - - -
A6.6.4.3. Sensors - - - -
A6.6.4.4. Switches - - - -
A6.6.4.5. Junction boxes - - - -
A6.6.4.6. Switch cards - - - -
A6.6.4.7. Relays - - - -
A6.6.4.8. Diodes - - - -
A6.6.5. Repair components
A6.6.5.1. Control handle - - - -
A6.6.5.2. Control panels - - - -
A6.6.6. Install components
A6.6.6.1. Control handle - - - -
A6.6.6.2. Sequence panel - - - -
A6.6.6.3. Sensors - - - -
A6.6.6.4. Switches - - - -
A6.6.6.5. Junction boxes - - - -
A6.6.6.6. Switch cards - - - -
A6.6.6.7. Relays - - - -
A6.6.6.8. Diodes - - - -
A6.6.7. Bench check
A6.6.7.1. Control handle - - - -
A6.6.7.2. Control panels - - - -
A6.7. ANTI-SKID SYSTEM
TR:
A6.7.1. Operational fundamentals - - - -
A6.7.2. Operational Check System* * - - - -
A6.7.3.. Troubleshoot System * - - - -
A6.7.4. .Inspect System Components * - - - -
A6.7.5. Remove components
A6.7.5.1. Detector and deflation valve - - - -
A6.7.5.2. Anti-skid Control box - - - -
A6.7.5.3. Control panel - - - -
A6.7.6. Repair components
A6.7.6.1. Anti-skid control box - - - -
C-5 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
84Attachment 6
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A6.7.6.2. Control panel - - - -
A6.7.7. Install components - - - -
A6.7.7.1. Detector and deflation valve - - - -
A6.7.7.2. Anti-skid Control box - - - -
A6.7.7.3. Control panel - - - -
A6.7.8. Bench check
A6.7.8.1. Anti-skid control box - - - -
A6.7.8.2. Control panel - - - -
A6.8. NOSE GEAR STEERING/KNEELING SYSTEM
TR:
A6.8.1. Operational fundamentals - - - -
A6.8.2. Troubleshoot System - - - -
A6.8.3. Inspect System Components - - - -
A6.8.4. Remove components
A6.8.4.1. Indicator - - - -
A6.8.4.2. Sensors/switches - - - -
A6.8.5. Install components
A6.8.5.1. Indicator - - - -
A6.8.5.2. Sensors/switches - - - -
A6.9. PRIMARY FLIGHT CONTROL SYSTEM
TR:
A6.9.1. Operational fundamentals - - - -
A6.9.2. Operational check System
A6.9.2.1. Primary flight control - - - -
A6.9.2.2. Trim and indication - - - -
A6.9.3. Troubleshoot System
A6.9.3.1. Primary flight control - - - -
A6.9.3.2. Trim and indication - - - -
A6.9.4. Inspect System Components - - - -
A6.10. SECONDARY FLIGHT CONTROL SYSTEM
TR:
A6.10.1. Operational fundamentals - - - -
A6.10.2. Operational check System
A6.10.2.1. Secondary flight control - - - -
A6.10.2.2. Trim and indication - - - -
A6.10.3. Troubleshoot System
A6.10.3.1. Secondary flight control - - - -
A6.10.3.2. Trim and indication - - - -
C-5 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
85Attachment 6
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A6.10.4. Inspect System Components - - - -
A6.10.5. Remove components
A6.10.5.1. Flap/slate transmitters - - - -
A6.10.5.2. Asymmetry/Proximity control box - - - -
A6.10.5.3. Diodes - - - -
A6.10.5.4. Relays - - - -
A6.10.5.5. Proximity sensors
TR: TO 1C-5A-2-9JG-3-1
- - - -
A6.10.6. Install components
A6.10.6.1. Flap/slate transmitters - - - -
A6.10.6.2. Asymmetry/Proximity control box - - - -
A6.10.6.3. Diodes - - - -
A6.10.6.4. Relays - - - -
A6.10.6.5. Proximity sensors
TR: TO 1C-5A-2-9JG-3-1
- - - -
A6.10.7. Bench Ck/Repair Asymmetry/Proximity Control Box - - - -
A6.10.8. Null flaps and slat brake transmitter
TR: TO 1C-5A-2-9JG-3-1
- - - -
A6.11. OVERHEAT/FIRE WARNING SYSTEM
TR:
A6.11.1. Operational fundamentals - - - -
A6.11.2. Operational Check System - - - -
A6.11.3. Troubleshoot System * - - - -
A6.11.4. Inspect System Components * - - - -
A6.11.5. Remove components
A6.11.5.1. Smoke detector - - - -
A6.11.5.2. Control box - - - -
A6.11.5.3. Flame detector - - - -
A6.11.5.4. Sensors/sensing elements - - - -
A6.11.6. Repair components
A6.11.6.1. Smoke detector - - - -
A6.11.6.2. Control box - - - -
A6.11.7. Install components
A6.11.7.1. Smoke detector - - - -
A6.11.7.2. Control box - - - -
A6.11.7.3. Flame detector - - - -
A6.11.7.4. Sensors/sensing elements - - - -
A6.11.8. Bench check
C-5 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
86Attachment 6
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A6.11.8.1. Smoke detector - - - -
A6.11.8.2. Control box - - - -
A6.12. FIRE EXTINGUISHING SYSTEM
A6.12.1. Operational fundamentals - - - -
A6.12.2. Operational check System
A6.12.2.1. Engine fire ext. system - - - -
A6.12.2.2. APU fire ext. system - - - -
A6.12.3. Troubleshoot system - - - -
A6.12.4. Inspect system Components * - - - -
A6.12.5. Remove components
A6.12.5.1. Fire bottles - - - -
A6.12.5.2. Plumbing - - - -
A6.12.5.3. Squib - - - -
A6.12.5.4. Panels - - - -
A6.12.6. Install components
A6.12.6.1. Fire bottles - - - -
A6.12.6.2. Plumbing - - - -
A6.12.6.3. Squib - - - -
A6.12.6.4. Panels - - - -
A6.12.7. Perform ignition ck of squibs - - - -
A6.12.8. Bench Ck/Repair Panels - - - -
A6.13. FIRE SUPPRESSION/FUEL INERTING AND PRESSURIZATION
TR:
A6.13.1. Operational fundamentals - - - -
A6.13.2. Operational check system - - - -
A6.13.3. Troubleshoot system - - - -
A6.13.4. Inspect System Components * - - - -
A6.13.5. Remove components
A6.13.5.1. CPU - - - -
A6.13.5.2. CTS loops - - - -
A6.13.5.3. Dewar assembly - - - -
A6.13.5.4. Plumbing - - - -
A6.13.5.5. Main FSS panel - - - -
A6.13.5.6. Cargo FSS panel - - - -
A6.13.5.7. Nose FSS panel - - - -
A6.13.5.8. FSS LN2 service panel - - - -
A6.13.5.9. FSS LN2 valves and regulators - - - -
C-5 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
87Attachment 6
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A6.13.5.10. Signal Conditioner - - - -
A6.13.6. Repair components
A6.13.6.1. CPU - - - -
A6.13.6.2. Dewar assembly - - - -
A6.13.6.3. Main FSS panel - - - -
A6.13.6.4. Cargo FSS panel - - - -
A6.13.6.5. Nose FSS panel - - - -
A6.13.6.6. FSS LN2 service panel - - - -
A6.13.6.7. FSS LN2 valves and regulators - - - -
A6.13.6.8. Signal Conditioner - - - -
A6.13.7. Install components
A6.13.7.1. CPU - - - -
A6.13.7.2. CTS loops - - - -
A6.13.7.3. Dewar assembly - - - -
A6.13.7.4. Plumbing - - - -
A6.13.7.5. Main FSS panel - - - -
A6.13.7.6. Cargo FSS panel - - - -
A6.13.7.7. Nose FSS panel - - - -
A6.13.7.8. FSS LN2 service panel - - - -
A6.13.7.9. FSS LN2 valves and regulators - - - -
A6.13.7.10. Signal Conditioner - - - -
A6.13.8. Bench check
A6.13.8.1. CPU - - - -
A6.13.8.2. Dewar assembly - - - -
A6.13.8.3. Main FSS panel - - - -
A6.13.8.4. Cargo FSS panel - - - -
A6.13.8.5. Nose FSS panel - - - -
A6.13.8.6. FSS LN2 service panel - - - -
A6.13.8.7. FSS LN2 valves and regulators - - - -
A6.13.8.8. Signal Conditioner - - - -
A6.13.9. Activate/deactivate FSS - - - -
A6.13.10. Purge Dewar - - - -
A6.14. MASTER CAUTION/WARNING SYSTEM
TR:
A6.14.1. Operational fundamentals - - - -
A6.14.2. Operational Check System - - - -
A6.14.3. Troubleshoot system * - - - -
A6.14.4. Inspect system Components * - - - -
C-5 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
88Attachment 6
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A6.14.5. Remove components
A6.14.5.1. Annunciator assembly - - - -
A6.14.5.2. Control box - - - -
A6.14.5.3. Light cards - - - -
A6.14.6. Repair components
A6.14.6.1. Annunciator assembly - - - -
A6.14.6.2. Control box - - - -
A6.14.7. Install components
A6.14.7.1. Annunciator assembly - - - -
A6.14.7.2. Control box - - - -
A6.14.7.3. Light cards - - - -
A6.14.8. Bench check
A6.14.8.1. Annunciator assembly - - - -
A6.14.8.2 Control box - - - -
A6.15. DOOR CONTROL AND WARNING SYSTEM
TR:
A6.15.1. Operational fundamentals - - - -
A6.15.2. Operational Check System - - - -
A6.15.3. Troubleshoot system * - - - -
A6.15.4. Inspect system Components * - - - -
A6.15.5. Remove components
A6.15.5.1. Sensors - - - -
A6.15.5.2. Switches - - - -
A6.15.5.3. Control panels - - - -
A6.15.6. Install components
A6.15.6.1. Sensors - - - -
A6.15.6.2. Switches - - - -
A6.15.6.3. Control panels - - - -
A6.15.7. Bench Ck/Repair control panels - - - -
A6.16. FUEL WARNING AND CONTROL SYSTEM
TR:
A6.16.1. Operational fundamentals - - - -
A6.16.2. Operational Check System - - - -
A6.16.3. Troubleshoot System * - - - -
A6.16.4. Inspect System Components * - - - -
A6.17. INFLIGHT REFUELING SYSTEM
A6.17.1. Operational fundamentals - - - -
A6.17.2. Operational Check System - - - -
C-5 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
89Attachment 6
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A6.17.3. Troubleshoot System - - - -
A6.17.4. Inspect System Components - - - -
A6.18. START AND IGNITION SYSTEM
TR:
A6.18.1. Operational fundamentals - - - -
A6.18.2. Operational Check System - - - -
A6.18.3. Troubleshoot System * - - - -
A6.18.4. Inspect System Components * - - - -
A6.19. NESA ANTI-ICING SYSTEM
TR:
A6.19.1. Operational fundamentals - - - -
A6.19.2. Operational Check System - - - -
A6.19.3. Troubleshoot system * - - - -
A6.19.4. Inspect System Components * - - - -
A6.19.5. Remove components
A6.19.5.1. Windshield Heat control box - - - -
A6.19.5.2. Transformers - - - -
A6.19.6. Install components
A6.19.6.1. Windshield Heat control box - - - -
A6.19.6.2. Transformers - - - -
A6.19.7. Bench Ck/Repair windshield heat control box - - - -
A6.20. BLEED AIR DISTRIBUTION SYSTEM
TR:
A6.20.1. Operational fundamentals - - - -
A6.20.2. Operational check System - - - -
A6.20.3. Troubleshoot system * - - - -
A6.20.4. Inspect system Components * - - - -
A6.20.5. Remove components
A6.20.5.1. Valves - - - -
A6.20.5.2. Sensors - - - -
A6.20.5.3. Ducts - - - -
A6.20.5.4. Switches - - - -
A6.20.6. Install components
A6.20.6.1. Valves - - - -
A6.20.6.2. Sensors - - - -
A6.20.6.3. Ducts - - - -
A6.20.6.4. Switches - - - -
A6.20.7. Perform leakage test using high pressure air source - - - -
C-5 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
90Attachment 6
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A6.20.8. Perform leakage test using APU's - - - -
A6.20.9. Repair Compensator Ducts - - - -
A6.21. BLEED AIR OVERHEAT SYSTEM
A6.21.1. Operational fundamentals - - - -
A6.21.2. Operational check System - - - -
A6.21.3. Troubleshoot system *R - - - -
A6.21.4. Inspect system Components * - - - -
A6.21.5. Remove components
A6.21.5.1. Sensing elements - - - -
A6.21.5.2. Locator relay - - - -
A6.21.5.3. Control box - - - -
A6.21.6. Install components
A6.21.6.1. Sensing elements - - - -
A6.21.6.2. Locator relay - - - -
A6.21.6.3. Control box - - - -
A6.21.7. Bench Ck/Repair control box - - - -
A6.21.8. Calibrate locator relay * - - - -
A6.22. AIR CONDITIONING SYSTEM
TR:
A6.22.1. Operational fundamentals - - - -
A6.22.2. Operational Check System - - - -
A6.22.3. Troubleshoot system * - - - -
A6.22.4. Inspect system Components * - - - -
A6.22.5. Remove components
A6.22.5.1. Valves - - - -
A6.22.5.2. Sensors - - - -
A6.22.5.3. Switches - - - -
A6.22.5.4. Temp cont. boxes - - - -
A6.22.5.5. Ducts - - - -
A6.22.5.6. Cooling Turbine - - - -
A6.22.5.7. Water separator - - - -
A6.22.5.8. Heat exchanger - - - -
A6.22.5.9. Fan and sensor - - - -
A6.22.5.10. Van axial Fan assembly - - - -
A6.22.5.11. Mixing chamber - - - -
A6.22.5.12. Air Exit Valve Assembly - - - -
A6.22.6. Repair components
A6.22.6.1. Valves - - - -
C-5 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
91Attachment 6
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A6.22.6.2. Temp cont. boxes - - - -
A6.22.6.3. Water separator - - - -
A6.22.6.4. Fan and sensor - - - -
A6.22.6.5. Van axial Fan assembly - - - -
A6.22.6.6. Air Exit Valve Assembly - - - -
A6.22.7. Install components
A6.22.7.1. Valves - - - -
A6.22.7.2. Sensors - - - -
A6.22.7.3. Switches - - - -
A6.22.7.4. Temp cont. boxes - - - -
A6.22.7.5. Ducts - - - -
A6.22.7.6. Cooling Turbine - - - -
A6.22.7.7. Water separator - - - -
A6.22.7.8. Heat exchanger - - - -
A6.22.7.9. Fan and sensor - - - -
A6.22.7.10. Van axial Fan assembly - - - -
A6.22.7.11. Mixing chamber - - - -
A6.22.7.12. Air Exit Valve Assembly - - - -
A6.22.8. Bench check
A6.22.8.1. Valves - - - -
A6.22.8.2. Temp cont. boxes - - - -
A6.22.8.3. Heat exchanger - - - -
A6.22.8.4. Fan and sensor - - - -
A6.22.8.5. Van axial Fan assembly - - - -
A6.22.8.6. Air Exit Valve Assembly - - - -
A6.22.9. Perform leakage checks - - - -
A6.23. PRESSURIZATION SYSTEM
TR:
A6.23.1. Operational fundamentals - - - -
A6.23.2. Operational Check System - - - -
A6.23.3. Troubleshoot system * - - - -
A6.23.4. Inspect system Components * - - - -
A6.23.5. Remove components
A6.23.5.1. Thrust recovery actuator - - - -
A6.23.5.2. Auto press. Cont. box - - - -
A6.23.5.3. Outflow valve - - - -
A6.23.5.4. Indicators - - - -
A6.23.5.5. Switches - - - -
C-5 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
92Attachment 6
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A6.23.5.6. Panels - - - -
A6.23.5.7. Safety relief valve - - - -
A6.23.5.8. Potentiometer - - - -
A6.23.6. Repair components
A6.23.6.1. Panels - - - -
A6.23.6.2. Safety Valves - - - -
A6.23.7. Install components
A6.23.7.1. Thrust recovery actuator - - - -
A6.23.7.2. Auto press. Cont. box - - - -
A6.23.7.3. Outflow valve - - - -
A6.23.7.4. Indicators - - - -
A6.23.7.5. Switches - - - -
A6.23.7.6. Panels - - - -
A6.23.7.7. Safety relief valve - - - -
A6.23.7.8. Potentiometer - - - -
A6.23.8. Bench check
A6.23.8.1. Panels - - - -
A6.23.8.2. Safety Valves - - - -
A6.23.9. Perform Built-In Test (BITE) of Automatic Pressurization System
- - - -
A6.23.10. Rig Outflow valve actuator * - - - -
A6.24. OXYGEN SYSTEM
TR: 15X-1-1
A6.24.1. Operational fundamentals - - - -
A6.24.2. Operational check System
A6.24.2.1. Crew - - - -
A6.24.2.2. Troop and passenger - - - -
A6.24.2.3. Lox indicating - - - -
A6.24.3. Troubleshoot system * - - - -
A6.24.4. Inspect system Components * - - - -
A6.24.5. Remove components
A6.24.5.1. Buildup/vent valve - - - -
A6.24.5.2. Drain/fill valve - - - -
A6.24.5.3. Press. Demand Regulators - - - -
A6.24.5.4. Cont. flow regulators - - - -
A6.24.5.5. Drop down masks - - - -
A6.24.5.6. Heat exchanger - - - -
A6.24.5.7. Recharge hose - - - -
C-5 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
93Attachment 6
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A6.24.5.8. Converters - - - -
A6.24.5.9. Indicators - - - -
A6.24.5.10. Plumbing - - - -
A6.24.5.11. Walk around bottle - - - -
A6.24.5.12. Regulator Hose assembly - - - -
A6.24.6. Install components
A6.24.6.1. Buildup/vent valve - - - -
A6.24.6.2. Drain/fill valve - - - -
A6.24.6.3. Press. Demand Regulators - - - -
A6.24.6.4. Cont. flow regulators - - - -
A6.24.6.5. Drop down masks - - - -
A6.24.6.6. Heat exchanger - - - -
A6.24.6.7. Recharge hose - - - -
A6.24.6.8. Converters - - - -
A6.24.6.9. Indicators - - - -
A6.24.6.10. Plumbing - - - -
A6.24.6.11. Walk around bottle - - - -
A6.24.6.12. Regulator Hose assembly - - - -
A6.24.7. Perform leakage check - - - -
A6.24.8. Purge system - - - -
A6.24.9. Service/drain system - - - -
A6.24.10. Bench Ck/Repair Walk around Bottle - - - -
A6.24.11. Connect/Disconnect Cryogenic vent plugs/tubes, and equipment to vent ports TR: TO 1C-5A-2-2 and applicable equipment Technical Orders
- - - -
A6.25. Windshield wiper system
A6.25.1 Operational fundamentals - - - -
A6.25.2. Operational Check System - - - -
A6.25.3. Troubleshoot system - - - -
A6.25.4. Inspect system Components - - - -
A6.25.5. Repair windshield wiper motor - - - -
A6.25.6. Bench Check windshield motor - - - -
A6.26. GALLEY/BUFFET
A6.26.1. Operational fundamentals - - - -
A6.26.2. Operational Check System - - - -
A6.26.3. Troubleshoot system - - - -
A6.26.4. Inspect system Components - - - -
A6.26.5. Repair components
A6.26.5.1. Oven - - - -
C-5 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
94Attachment 6
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A6.26.5.2. Refrigerator - - - -
A6.26.5.3. Coffee brewer - - - -
A6.26.6. Bench ck components
A6.26.6.1. Oven - - - -
A6.26.6.2. Refrigerator - - - -
A6.26.6.3. Coffee brewer - - - -
A6.27. HYDRAULIC CONTROL/INDICATION WARNING CIRCUITS
A6.27.1. Operational fundamentals - - - -
A6.27.2. Operational Check System - - - -
A6.27.3. Troubleshoot system - - - -
A6.27.4. Inspect system Components - - - -
A6.28. AIR TURBINE MOTOR
A6.28.1. Operational fundamentals - - - -
A6.28.2. Operational Check System - - - -
A6.28.3. Troubleshoot system - - - -
A6.28.4. Inspect System Components - - - -
A6.28.5. Remove components
A6.28.5.1. ATM assembly - - - -
A6.28.5.2. Filters - - - -
A6.28.5.3. Exhaust duct - - - -
A6.28.6. Install
A6.28.6.1. ATM assembly - - - -
A6.28.6.2. Filters - - - -
A6.28.6.3. Exhaust duct - - - -
A6-28.7. Service ATM with oil - - - -
A6.29. ENGINE THRUST REVERSER INDICATING SYSTEM
TR: 1C-5A-2-4
A6.29.1. Operational fundamentals - - - -
A6.29.2. Operational check system - - - -
A6.29.3. Troubleshoot system - - - -
A6.29.4. Inspect System Components - - - -
A6.30. AIRCREW EYE RESPIRATORY PROTECTION SYSTEM (AERP)
A6.30.1. Operational fundamentals - - - -
A6.30.2. Operational check system - - - -
A6.30.3. Troubleshoot system - - - -
A6.30.4. Inspect System Components - - - -
C-5 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
95Attachment 6
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A6.31. COMMON MAINTENANCE PRACTICES
TR:
A6.31.1. Perform duties of Concurrent Servicing Supervisor (CSS) for fuel service operations
TR: TO 1C-5A-2-1, 00-25-172
- - - -
A6.31.2. Perform duties of Concurrent Servicing Supervisor(CSS) for liquid oxygen (LOX) servicing operations
TR: TO 1C-5A-2-1, 00-25-172
- - - -
A6.31.3. Operate FMS/GPS-800 control head for communication (UHF/VHF)
TR: TO 1C-5A-2-8-2S-34
- - - -
A6.31.4. Operate Auxiliary Power Unit (APU) and Air TurbineMotor (ATM)
TR: TO 1C-5A-2-4, 1C-5A-2-4CL-1
- - - -
A6.31.5. Operate C-5B MADAR II System
TR: 1C-5A-102, 1C-5A-102-1
- - - -
A6.31.6. Bench ck/repair linear and rotary actuators - - - -
A6.31.7. Inspect/troubleshoot RAT - - - -
A6.31.8. Inspect/Repair explosion proof lights - - - -
C-9 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
96Attachment 7
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
ATTACHMENT 7
NOTE 1: In addition to attachment 2, the tasks and knowledge in attachment 6 will be performed by personnel assigned to maintain C-9 aircraft.
NOTE 2: Users are responsible for annotating training references to identify current references pending STS revision.
NOTE 3: Items marked in columns 2a or 2b marked with a (*R) are optional core tasks for ANG and AFRC.
NOTE 4: Address comments and recommended changes through Unit Training Managers to the MAJCOM Maintenance Training Manager @ HQ AMC/LGMMT, 402 SUnit 2A2, Scott AFB, IL 62225-5308; or call DSN 576-4787. MAJCOM Training and Functional Managers forward inputs to the AETC Training Manager, DSN 736-27
A7.1. AC POWER SYSTEM
TR: APPLICABLE AIRCRAFT TO’S
A7.1.1. Operational fundamentals - - - -
A7.1.2. Operational Check System * - - - -
A7.1.3. Troubleshoot System * - - - -
A7.1.4. Inspect System Components * - - - -
A7.1.5. Remove components
A7.1.5.1. Engine driven generator - - - -
A7.1.5.2. AC generator control panel - - - -
A7.1.5.3. AC bus control panel - - - -
A7.1.5.4. AC voltage regulator - - - -
A7.1.5.5. AC bus power relays - - - -
A7.1.5.6. 60 cycle converter - - - -
A7.1.6. Repair components - - - -
A7.1.7. Install components
A7.1.7.1. Engine driven generator - - - -
A7.1.7.2. AC generator control panel - - - -
A7.1.7.3. AC bus control panel - - - -
A7.1.7.4. AC voltage regulator - - - -
A7.1.7.5. AC bus power relays - - - -
A7.1.7.6. 60 cycle converter - - - -
A7.2. DC POWER SYSTEM
TR: APPLICABLE AIRCRAFT TO’S
A7.2.1. Operational fundamentals - - - -
A7.2.2. Operational Check System * - - - -
A7.2.3. Troubleshoot System * - - - -
A7.2.4. Inspect System Components * - - - -
A7.2.5. Remove components
A7.2.5.1. DC aircraft batteries - - - -
A7.2.5.2. Battery charger - - - -
A7.2.5.3. Transformer rectifiers - - - -
A7.2.6. Repair components - - - -
C-9 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
97Attachment 7
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A7.2.7. Install components
A7.2.7.1. DC aircraft batteries - - - -
A7.2.7.2. Battery charger - - - -
A7.2.7.3. Transformer rectifiers - - - -
A7.3. EXTERNAL POWER SYSTEM
TR: APPLICABLE AIRCRAFT TO’S
A7.3.1. Operational fundamentals - - - -
A7.3.2. Operational Check System * - - - -
A7.3.3. Troubleshoot System * - - - -
A7.3.4. Inspect System Components * - - - -
A7.3.5. Remove and install components - - - -
A7.3.6. Repair components - - - -
A7.4. LIGHTING SYSTEM
TR: APPLICABLE AIRCRAFT TO’S
A7.4.1. Operational fundamentals - - - -
A7.4.2. Operational Check System * - - - -
A7.4.3. Troubleshoot System * - - - -
A7.4.4 .Inspect System Components * - - - -
A7.4.5. Remove components
A7.4.5.1. Light plates * - - - -
A7.4.5.2. Lighting control panels - - - -
A7.4.6. Repair components - - - -
A7.4.7. Remove and install components
A7.4.7.1. Light plates * - - - -
A7.4.7.2. Lighting control panels - - - -
A7.5. LANDING GEAR SYSTEM
TR: APPLICABLE AIRCRAFT TO’S
A7.5.1. Operational fundamentals - - - -
A7.5.2. Operational Check System * - - - -
A7.5.3. Troubleshoot System * - - - -
A7.5.4. Inspect System Components * - - - -
A7.5.5. Remove and install components
A7.5.5.1. Landing gear proximity switches - - - -
A7.5.5.2. Landing gear mechanical switches * - - - -
A7.5.6. Remove and install components
A7.5.6.1. Landing gear proximity switches - - - -
A7.5.6.2. Landing gear mechanical switches * - - - -
- - - -
C-9 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
98Attachment 7
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A7.6. ANTI-SKID SYSTEM
TR: APPLICABLE AIRCRAFT TO’S
A7.6.1. Operational fundamentals - - - -
A7.6.2. Operational check System * - - - -
A7.6.2.1. Servo valve - - - -
A7.6.2.2. Anti-skid control computer - - - -
A7.6.2.3. Ground control relay - - - -
A7.6.3. Troubleshoot System * - - - -
A7.6.4. Inspect System Components * - - - -
A7.6.5. Remove wheel speed transducer - - - -
A7.6.6. Repair components - - - -
A7.6.7. Install wheel speed transducer - - - -
A7.7. NOSE GEAR SYSTEM
TR: APPLICABLE AIRCRAFT TO’S
A7.7.1. Operational fundamentals - - - -
A7.7.2. Operational Check System * - - - -
A7.7.3. Troubleshoot System * - - - -
A7.7.4. Inspect System Components * - - - -
A7.7.5. Remove and install components - - - -
A7.7.6. Repair components - - - -
A7.8. PRIMARY FLIGHT CONTROL SYSTEM
TR: APPLICABLE AIRCRAFT TO’S
A7.8.1. Operational fundamentals - - - -
A7.8.2. Operational check System * - - - -
A7.8.3. Troubleshoot System * - - - -
A7.8.4. Inspect System Components * - - - -
A7.8.5. Remove components
A7.8.5.1. Slat disagreement switch * - - - -
A7.8.5.2. Rudder travel unrestricted switch - - - -
A7.8.5.3. Rudder throw limiter stop switch - - - -
A7.8.5.4. Flap rudder position switch - - - -
A7.8.6. Repair components - - - -
A7.8.7. Install components
A7.8.7.1. Slat disagreement switch * - - - -
A7.8.7.2. Rudder travel unrestricted switch - - - -
A7.8.7.3. Rudder throw limiter stop switch - - - -
A7.8.7.4. Flap rudder position switch - - - -
- - - -
C-9 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
99Attachment 7
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A7.9. OVERHEAT/FIRE WARNING SYSTEM
TR: APPLICABLE AIRCRAFT TO’S
A7.9.1. Operational fundamentals - - - -
A7.9.2. Operational Check System * - - - -
A7.9.3. Troubleshoot System * - - - -
A7.9.4. Inspect System Components * - - - -
A7.9.5. Remove and install components - - - -
A7.9.6. Repair components - - - -
A7.10. FIRE EXTINGUISHING SYSTEM
TR: APPLICABLE AIRCRAFT TO’S
A7.10.1. Operational fundamentals - - - -
A7.10.2. Operational Check System - - - -
A7.10.2.1. Fire warning horn * - - - -
A7.10.2.2. Aft accessory compartment overheat system - - - -
A7.10.3. Troubleshoot System * - - - -
A7.10.4. Inspect System Components * - - - -
A7.10.5. Remove components
A7.10.5.1. Engine fire detector loop * - - - -
A7.10.5.2. APU fire detector loop - - - -
A7.10.5.3. Fire detector control unit - - - -
A7.10.5.4. Extinguisher explosive cartridges * - - - -
A7.10.6. Repair components - - - -
A7.10.7. Install components
A7.10.7.1. Engine fire detector loop * - - - -
A7.10.7.2. APU fire detector loop - - - -
A7.10.7.3. Fire detector control unit - - - -
A7.10.7.4. Extinguisher explosive cartridges * - - - -
A7.11. FLIGHT CONTROL TAKEOFF WARNING SYSTEM
TR: APPLICABLE AIRCRAFT TO’S
A7.11.1. Operational fundamentals - - - -
A7.11.2. Operational Check System * - - - -
A7.11.3. Troubleshoot System * - - - -
A7.11.4. Inspect System Components * - - - -
A7.11.5. Remove and install components - - - -
A7.11.6. Repair components - - - -
A7.12. MASTER CAUTION/WARNING SYSTEM
TR: APPLICABLE AIRCRAFT TO’S
C-9 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
100Attachment 7
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A7.12.1. Operational fundamentals - - - -
A7.12.2. Operational Check System * - - - -
A7.12.3. Troubleshoot System * - - - -
A7.12.4. Inspect System Components * - - - -
A7.12.5. Remove and install components - - - -
A7.12.6. Repair components - - - -
A7.13. DOOR CONTROL AND WARNING SYSTEM
TR: APPLICABLE AIRCRAFT TO’S
A7.13.1. Operational fundamentals - - - -
A7.13.2. Operational Check System - - - -
A7.13.3. Troubleshoot System - - - -
A7.13.4. Inspect System Components - - - -
A7.13.5. Remove and install components - - - -
A7.13.6. Repair components - - - -
A7.14. FUEL WARNING AND CONTROL SYSTEM
TR: APPLICABLE AIRCRAFT TO’S
A7.14.1. Operational fundamentals - - - -
A7.14.2. Operational Check System - - - -
A7.14.3. Troubleshoot System - - - -
A7.14.4. Inspect System Components - - - -
A7.14.5. Remove and install components - - - -
A7.14.6. Repair components - - - -
A7.15. START AND IGNITION SYSTEM
TR: APPLICABLE AIRCRAFT TO’S
A7.15.1. Operational fundamentals - - - -
A7.15.2. Operational Check System - - - -
A7.15.3. Troubleshoot System - - - -
A7.15.4. Inspect System Components - - - -
A7.15.5. Remove and install components - - - -
A7.15.6. Repair components - - - -
A7.16. ANTI-ICING SYSTEM
TR: APPLICABLE AIRCRAFT TO’S
A7.16.1. Operational fundamentals - - - -
A7.16.2. Operational Check System * - - - -
A7.16.2.1. Airfoil ice protection system - - - -
A7.16.2.2. Windows and windshield anti-icing/anti-fogging - - - -
A7.16.2.3. ICE protection control anticipator - - - -
A7.16.2.4 .ICE protection control thermostat - - - -
C-9 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
101Attachment 7
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A7.16.3. Troubleshoot System - - - -
A7.16.4. Inspect System Components - - - -
A7.16.5. Remove components
A7.16.5.1. Augmentation valve - - - -
A7.16.5.2. Pneumatic pilot pressure regulator - - - -
A7.16.6. Repair components - - - -
A7.16.7. Iinstall components
A7.16.7.1. Augmentation valve - - - -
A7.16.7.2. Pneumatic pilot pressure regulator - - - -
A7.17. BLEED AIR DISTRIBUTION SYSTEM
TR: APPLICABLE AIRCRAFT TO’S
A7.17.1. Operational fundamentals - - - -
A7.17.2. Operational Check System * - - - -
A7.17.3. Troubleshoot System * - - - -
A7.17.4. Inspect System Components * - - - -
A7.17.5. Remove and install components - - - -
A7.17.6. Repair components - - - -
A7.18. AIR CONDITIONING SYSTEM
TR: APPLICABLE AIRCRAFT TO’S
A7.18.1. Operational fundamentals - - - -
A7.18.2. Operational Check System * - - - -
A7.18.3. Troubleshoot System * - - - -
A7.18.4. Inspect System Components * - - - -
A7.18.5. Remove components
A7.18.5.1. Air conditioning water separator * - - - -
A7.18.5.2. Heat exchanger cooling air fan - - - -
A7.18.5.3. Air conditioning pressure regulator valve - - - -
A7.18.5.4. Cooling turbine - - - -
A7.18.5.5. Primary heat exchanger - - - -
A7.18.5.6. Secondary heat exchanger - - - -
A7.18.5.7. Instrument cooling fan * - - - -
A7.18.5.8. Radio rack cooling fan - - - -
A7.18.5.9. Temperature control valve and position indicator - - - -
A7.18.6. Repair components - - - -
A7.18.7. Iinstall components
A7.18.7.1. Air conditioning water separator * - - - -
A7.18.7.2. Heat exchanger cooling air fan - - - -
A7.18.7.3. Air conditioning pressure regulator valve - - - -
C-9 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
102Attachment 7
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A7.18.7.4. Cooling turbine - - - -
A7.18.7.5. Primary heat exchanger - - - -
A7.18.7.6. Secondary heat exchanger - - - -
A7.18.7.7. Instrument cooling fan * - - - -
A7.18.7.8. Radio rack cooling fan - - - -
A7.18.7.9. Temperature control valve and position indicator - - - -
A7.19. PRESSURIZATION SYSTEM
TR: APPLICABLE AIRCRAFT TO’S
A7.19.1 Operational fundamentals - - - -
A7.19.2. Operational Check System * - - - -
A7.19.3. Troubleshoot System * - - - -
A7.19.4. Inspect System Components * - - - -
A7.19.5. Remove components
A7.19.5.1. Cabin pressure safety valve - - - -
A7.19.5.2. Cabin pressure controller - - - -
A7.19.5.3. Pneumatic pressure transmitter - - - -
A7.19.6. Repair components - - - -
A7.19.7. Iinstall components
A7.19.7.1. Cabin pressure safety valve - - - -
A7.19.7.2. Cabin pressure controller - - - -
A7.19.7.3. Pneumatic pressure transmitter - - - -
A7.20. LIQUID COOLANT SYSTEM
TR: APPLICABLE AIRCRAFT TO’S
A7.20.1. Operational fundamentals - - - -
A7.20.2. Operational Check System - - - -
A7.20.3. Troubleshoot System - - - -
A7.20.4. Inspect System Components - - - -
A7.20.5. Remove and install components - - - -
A7.20.6. Repair components - - - -
A7.21. OXYGEN SYSTEM
TR: APPLICABLE AIRCRAFT TO’S; 15X-1-
A7.21.1. Operational fundamentals - - - -
A7.21.2. Operational Check System - - - -
A7.21.2.1. Crew Oxygen System * - - - -
A7.21.2.2 Patient Oxygen System * - - - -
A7.21.2.3 Therapeutic Oxygen system * - - - -
A7.21.3. Troubleshoot System - - - -
A7.21.3.1 Crew Oxygen System - - - -
C-9 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
103Attachment 7
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A7.21.3.2 Patient Oxygen System - - - -
A7.21.3.3 Therapeutic Oxygen system - - - -
A7.21.4 .Inspect System Components - - - -
A7.21.5. Remove components
A7.21.5.1. Build up and vent valve * - - - -
A7.21.5.2. Passenger converter - - - -
A7.21.5.3. Crew converter - - - -
A7.21.5.4. Diluter-demand regulator - - - -
A7.21.6. Repair components - - - -
A7.21.7. Iinstall components
A7.21.7.1. Build up and vent valve * - - - -
A7.21.7.2. Passenger converter - - - -
A7.21.7.3. Crew converter - - - -
A7.21.7.4. Diluter-demand regulator - - - -
A7.22. MISCELLANEOUS SYSTEMS
TR: APPLICABLE AIRCRAFT TO’S
A7.22.1. Operational fundamentals - - - -
A7.22.2. Operational check - - - -
A7.22.2.1. Fresh water service panel heat element - - - -
A7.22.2.2. Gallery waste water drain mast heater - - - -
A7.22.3. Troubleshoot System - - - -
A7.22.4. Inspect System Components - - - -
A7.22.5. Remove vacuum pump * - - - -
A7.22.6. Repair components - - - -
A7.22.7. Install vacuum pump * - - - -
C-17 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
104Attachment 8
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
ATTACHMENT 8
NOTE 1: In addition to attachment 2, the tasks and knowledge in attachment 8 will be performed by personnel assigned to maintain C-17 aircraft.
NOTE 2: Users are responsible for annotating training references to identify current references pending STS revision.
NOTE 3: Items marked in columns 2a or 2b marked with a (*R) are optional core tasks for ANG and AFRC.
NOTE 4: Address comments and recommended changes through Unit Training Managers to the MAJCOM Maintenance Training Manager @ HQ AMC/LGMMT, 402 SUnit 2A2, Scott AFB, IL 62225-5308; or call DSN 576-4787. MAJCOM Training and Functional Managers forward inputs to the AETC Training Manager, DSN 736-27
A8.1 AC POWER SYSTEM
TR: APPLICABLE AIRCRAFT TO’S
A8.1.1. Operational fundamentals - - - -
A8.1.2. Operational check - - - -
A8.1.2.1. Generating and control system
TR: 1C-17A-2-24JG series
* - - - -
A8.1.2.2 .Interrogation of APU/EPCU
TR: 1C-17A-2-24JG series
*R - - - -
A8.1.2.3. APU generation and control system
TR: 1C-17A-2-24JG series
* - - - -
A8.1.2.4. Tie controls system
TR: 1C-17A-2-24JG series
- - - -
A8.1.3. Troubleshoot
A8.1.3.1. Electrical sys using FI manual
TR: 1C-17A-2-24FI-00-1
*R - - - -
A8.1.4 .Inspect System Components *R - - - -
A8.1.5. Remove components
A8.1.5.1. Current transformer
TR: 1C-17A-2-24JG series
- - - -
A8.1.5.2. Remote power controller
TR: 1C-17A-2-24JG series
- - - -
A8.1.5.3. Remote control circuit breaker
TR: 1C-17A-2-24JG series
- - - -
A8.1.5.4. Electrical light transmitting indicating panel
TR: 1C-17A-2-24JG series
- - - -
A8.1.5.5. Electrical control panel
TR: 1C-17A-2-24JG series
*R - - - -
A8.1.5.6. Generator control unit
TR: 1C-17A-2-24JG series
- - - -
A8.1.5.7. APU/EPCU
TR: 1C-17A-2-24JG series
*R - - - -
A8.1.5.8. Frequency converter
TR: 1C-17A-2-24JG series
- - - -
C-17 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
105Attachment 8
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A8.1.6. Repair components - - - -
A8.1.7. Install components - - - -
A8.1.7.1. Current transformer
TR: 1C-17A-2-24JG series
A8.1.7.2. Remote power controller
TR: 1C-17A-2-24JG series
- - - -
A8.1.7.3. Remote control circuit breaker
TR: 1C-17A-2-24JG series
- - - -
A8.1.7.4. Electrical Light Transmitting Indicating Panel
TR: 1C-17A-2-24JG series
- - - -
A8.1.7.5. Electrical control panel
TR: 1C-17A-2-24JG series
* - - - -
A8.1.7.6. Generator control unit
TR: 1C-17A-2-24JG series
- - - -
A8.1.7.7. APU/EPCU
TR: 1C-17A-2-24JG series
* - - - -
A8.1.7.8. Frequency converter
TR: 1C-17A-2-24JG series
- - - -
A8.1.8 Bench check - - - -
A8.2. DC POWER SYSTEM
TR: APPLICABLE AIRCRAFT TO’S
A8.2.1. Operational fundamentals - - - -
A8.2.2. Operational check - - - -
A8.2.2.1 Power and control system (DC)
TR: 1C-17A-2-24JG series
* - - - -
A8.2.2.2. Batteries system
TR: 1C-17A-2-24JG series
- - - -
A8.2.2.3. Instrument power System
TR: 1C-17A-2-24JG series
- - - -
A8.2.2.4 Electrical outlet system
TR: 1C-17A-2-24JG series
- - - -
A8.2.2.5. Emergency power system
TR: 1C-17A-2-24JG series
- - - -
A8.2.2.6. Electrical protection system
TR: 1C-17A-2-24JG series
- - - -
A8.2.3. Troubleshoot - - - -
A8.2.4. Inspect System Components * - - - -
A8.2.5. Remove components
C-17 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
106Attachment 8
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A8.2.5.1. Transformer rectifier
TR: 1C-17A-2-24JG series
- - - -
A8.2.5.2. Four-wire electric plug on batteries
TR: 1C-17A-2-24JG series
- - - -
A8.2.5.3. Main battery
TR: 1C-17A-2-24JG series
- - - -
A8.2.5.4. Battery charger
TR: 1C-17A-2-24JG series
- - - -
A8.2.5.5. Electrical outlet panel assembly
TR: 1C-17A-2-24JG series
- - - -
A8.2.5.6. Electrical outlet power receptacle
TR: 1C-17A-2-24JG series
- - - -
A8.2.5.7. Static inverter
TR: 1C-17A-2-24JG series
- - - -
A8.2.5.8. Electrical grounding receptacle Connectors
TR: 1C-17A-2-24JG series
- - - -
A8.2.6. Repair components - - - -
A8.2.7. Install components
A8.2.7.1. Transformer rectifier
TR: 1C-17A-2-24JG series
- - - -
A8.2.7.2. Four-wire electric plug on batteries
TR: 1C-17A-2-24JG series
- - - -
A8.2.7.3 .Main battery
TR: 1C-17A-2-24JG series
- - - -
A8.2.7.4. Battery charger
TR: 1C-17A-2-24JG series
- - - -
A8.2.7.5. Electrical outlet panel assembly
TR: 1C-17A-2-24JG series
- - - -
A8.2.7.6. Electrical outlet power receptacle
TR: 1C-17A-2-24JG series
- - - -
A8.2.7.7. Static inverter
TR: 1C-17A-2-24JG series
- - - -
A8.2.7.8. Electrical grounding receptacle connectors
TR: 1C-17A-2-24JG series
- - - -
A8.2.8. Bench check - - - -
A8.2.9. Connect/disconnect main battery
TR: 1C-17A-2-12JG series
* - - - -
- - - -
C-17 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
107Attachment 8
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A8.3. EXTERNAL POWER SYSTEM
TR: APPLICABLE AIRCRAFT TO’S
A8.3.1. Operational fundamentals - - - -
A8.3.2. Operational check
A8.3.2.1. APU system operation
TR: 1C-C17A-2-49JG-00-1
* - - - -
A8.3.2.2. APU inlet door actuation system operational checkout
TR: 1C-C17A-2-49JG-10-1
- - - -
A8.3.3. Troubleshoot
A8.3.3.1. APU systems using FI manual
TR: 1C-C17A-2-49FI-00-1
*R - - - -
A8.3.4. Inspect System Components *R - - - -
A8.3.5. Remove components
A8.3.5.1. External electrical power receptacle connector
TR: 1C-17A-2-24JG series
- - - -
A8.3.5.2. APU inlet door open proximity sensor
TR: 1C-C17A-2-49JG-10-1
- - - -
A8.3.5.3. APU inlet door closed proximity sensor
TR: 1C-C17A-2-49JG-10-1
- - - -
A8.3.5.4. APU start and control panel
TR: 1C-C17A-2-49JG-60-1
- - - -
A8.3.5.5. APU boost voltage regulator
TR: 1C-C17A-2-49JG-60-1
- - - -
A8.3.5.6. APU hourmeter
TR: 1C-C17A-2-49JG-70-1
- - - -
A8.3.6. Repair components - - - -
A8.3.7. Install components
A8.3.7.1. External electrical power receptacle connector
TR: 1C-17A-2-24JG series
- - - -
A8.3.7.2. APU inlet door open proximity sensor
TR: 1C-C17A-2-49JG-10-1
- - - -
A8.3.7.3. APU inlet door closed proximity sensor
TR: 1C-C17A-2-49JG-10-1
- - - -
A8.3.7.4. APU start and control panel
TR: 1C-C17A-2-49JG-60-1
- - - -
A8.3.7.5. APU boost voltage regulator
TR: 1C-C17A-2-49JG-60-1
- - - -
- - - -
C-17 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
108Attachment 8
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A8.3.7.6. APU hourmeter
TR: 1C-C17A-2-49JG-70-1
- - - -
A8.3.8. Bench check - - - -
A8.3.9. Connect/disconnect ext elect. power
TR: 1C-17A-2-10JG series
* - - - -
A8.4. LIGHTING SYSTEM
TR: APPLICABLE AIRCRAFT TO’S
A8.4.1. Operational fundamentals - - - -
A8.4.2. Operational check
A8.4.2.1. Instrument and panel system
TR: 1C-17A-2-33JG series
- - - -
A8.4.2.2. Main instr, t-storm/emer backup and nvg lighting control
TR: 1C-17A-2-33JG series
- - - -
A8.4.2.3. Glareshield floodlight
TR: 1C-17A-2-33JG series
- - - -
A8.4.2.4. Overhead panel floodlight
TR: 1C-17A-2-33JG series
- - - -
A8.4.2.5. Pedestal floodlight
TR: 1C-17A-2-33JG series
- - - -
A8.4.2.6. EPC floodlight assembly
TR: 1C-17A-2-33JG series
- - - -
A8.4.2.7. Pilot t-storm light
TR: 1C-17A-2-33JG series
- - - -
A8.4.2.8. Cockpit dome light
TR: 1C-17A-2-33JG series
- - - -
A8.4.2.9. EPC maintenance light
TR: 1C-17A-2-33JG series
- - - -
A8.4.2.10. Portable cockpit utility light assembly
TR: 1C-17A-2-33JG series
- - - -
A8.4.2.11. Flt compartment reading light
TR: 1C-17A-2-33JG series
- - - -
A8.4.2.12. Floor light assembly
TR: 1C-17A-2-33JG series
- - - -
A8.4.2.13. Crew rest area flood light
TR: 1C-17A-2-33JG series
- - - -
A8.4.2.14. Flight deck stairway light
TR: 1C-17A-2-33JG series
- - - -
A8.4.2.15. Crew rest area reading light - - - -
C-17 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
109Attachment 8
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
TR: 1C-17A-2-33JG series
A8.4.2.16. Bunk area reading light
TR: 1C-17A-2-33JG series
- - - -
A8.4.2.17. Lav lights
TR: 1C-17A-2-33JG series
- - - -
A8.4.2.18. Lav emergency call
TR: 1C-17A-2-33JG series
- - - -
A8.4.2.19. Galley table floodlight
TR: 1C-17A-2-33JG series
- - - -
A8.4.2.20. Aisle system
TR: 1C-17A-2-33JG series
- - - -
A8.4.2.21. Passenger warning sign
TR: 1C-17A-2-33JG series
- - - -
A8.4.2.22. Aeromedical lightning/call system
TR: 1C-17A-2-33JG series
- - - -
A8.4.2.23. Cargo and service compartments system
TR: 1C-17A-2-33JG series
- - - -
A8.4.2.24. Cargo incandescent light assembly
TR: 1C-17A-2-33JG series
- - - -
A8.4.2.25. Fluorescent light assembly
TR: 1C-17A-2-33JG series
- - - -
A8.4.2.26. Wheelwell service light
TR: 1C-17A-2-33JG series
- - - -
A8.4.2.27. Nose landing gear lock spot light
TR: 1C-17A-2-33JG series
- - - -
A8.4.2.28. Service/inspection light
TR: 1C-17A-2-33JG series
- - - -
A8.4.2.29. External power panel light assembly
TR: 1C-17A-2-33JG series
- - - -
A8.4.2.30. Vertical stabilizer flood service light
TR: 1C-17A-2-33JG series
- - - -
A8.4.2.31. Loadmaster instrument and control panel system
TR: 1C-17A-2-33JG series
- - - -
A8.4.2.32. Loadmaster station fluorescent desk light
TR: 1C-17A-2-33JG series
- - - -
A8.4.2.33. Forward loadmaster panel illuminating light assembly
TR: 1C-17A-2-33JG series
- - - -
A8.4.2.34. Aft loadmaster panel illuminating light assembly - - - -
C-17 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
110Attachment 8
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
TR: 1C-17A-2-33JG series
A8.4.2.35. Evaluator/instructor reading light assembly
TR: 1C-17A-2-33JG series
- - - -
A8.4.2.36. Curb light
TR: 1C-17A-2-33JG series
- - - -
A8.4.2.37. Portable inspection light
TR: 1C-17A-2-33JG series
- - - -
A8.4.2.38. Landing system
TR: 1C-17A-2-33JG series
- - - -
A8.4.2.39. Nose retractable landing light assembly
TR: 1C-17A-2-33JG series
- - - -
A8.4.2.40. Cargo staging floodlight
TR: 1C-17A-2-33JG series
- - - -
A8.4.2.41. Navigation system
TR: 1C-17A-2-33JG series
- - - -
A8.4.2.42. Anti-collision system
TR: 1C-17A-2-33JG series
- - - -
A8.4.2.43. Wing and engine nacelle scan system
TR: 1C-17A-2-33JG series
- - - -
A8.4.2.44. High intensity recognition system
TR: 1C-17A-2-33JG series
- - - -
A8.4.2.45. Formation system
TR: 1C-17A-2-33JG series
- - - -
A8.4.2.46. Aerial refueling light
TR: 1C-17A-2-33JG series
- - - -
A8.4.2.47. UARRSI perimeter illuminating panel
TR: 1C-17A-2-33JG series
- - - -
A8.4.2.48. Emergency lighting and power system
TR: 1C-17A-2-33JG series
* - - - -
A8.4.2.49. Refuel lighting system
TR: 1C-17A-2-33JG series
- - - -
A8.4.3. Troubleshoot
A8.4.3.1. Lighting system using FI manual
TR: 1C-17A-2-33FI-00-1
* - - - -
A8.4.4. Inspect System Components * - - - -
A8.4.5. Remove components
A8.4.5.1. Instrument and panel transmitting and indicating panels
TR: 1C-17A-2-33JG series
- - - -
C-17 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
111Attachment 8
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A8.4.5.2. Annunciator dimming unit
TR: 1C-17A-2-33JG series
*R - - - -
A8.4.5.3. Pilot ,copilot, and pedestal light transmitting panels
TR: 1C-17A-2-33JG series
- - - -
A8.4.5.4. Stairway light transmitting indicating panel
TR: 1C-17A-2-33JG series
- - - -
A8.4.5.5. Personnel warning light transmitting indicating panel
TR: 1C-17A-2-33JG series
- - - -
A8.4.5.6. Aeromedical light transmitting indicating panel
TR: 1C-17A-2-33JG series
- - - -
A8.4.5.7. External power panel light assembly
TR: 1C-17A-2-33JG series
- - - -
A8.4.5.8. Loadmaster instrument and control panel system components
TR: 1C-17A-2-33JG series
- - - -
A8.4.5.9. Loadmaster instrument and control panel annunciator dimming unit
TR: 1C-17A-2-33JG series
- - - -
A8.4.5.10. Anti-collision light power supply
TR: 1C-17A-2-33JG series
- - - -
A8.4.5.11. Recognition light power supply
TR: 1C-17A-2-33JG series
- - - -
A8.4.5.12. UARRSI perimeter illuminating panel
TR: 1C-17A-2-33JG series
- - - -
A8.4.5.13. Emergency battery
TR: 1C-17A-2-33JG series
* - - - -
A8.4.5.14. UARRSI lamp
TR: 1C-17A-2-33JG series
- - - -
A8.4.6. Repair components - - - -
A8.4.7. Install components
A8.4.7.1. Instrument and panel transmitting and indicating panels
TR: 1C-17A-2-33JG series
- - - -
A8.4.7.2. Annunciator dimming unit
TR: 1C-17A-2-33JG series
*R - - - -
- - - -
A8.4.7.3. Pilot ,copilot, and pedestal light transmitting panels
TR: 1C-17A-2-33JG series
- - - -
A8.4.7.4. Stairway light transmitting indicating panel - - - -
C-17 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
112Attachment 8
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
TR: 1C-17A-2-33JG series
A8.4.7.5. Personnel warning light transmitting indicating panel
TR: 1C-17A-2-33JG series
- - - -
A8.4.7.6. Aeromedical Light Transmitting indicating panel
TR: 1C-17A-2-33JG Series
- - - -
A8.4.7.7. External power panel light assembly
TR: 1C-17A-2-33JG series
- - - -
A8.4.7.8. Loadmaster instrument and control panel system components
TR: 1C-17A-2-33JG series
- - - -
A8.4.7.9. Loadmaster instrument and control panel annunciator dimming unit
TR: 1C-17A-2-33JG series
*R - - - -
A8.4.7.10. Anti-collision light power supply
TR: 1C-17A-2-33JG series
- - - -
A8.4.7.11. Recognition light power supply
TR: 1C-17A-2-33JG series
- - - -
A8.4.7.12. UARRSI perimeter illuminating panel
TR: 1C-17A-2-33JG series
- - - -
A8.4.7.13. Emergency battery
TR: 1C-17A-2-33JG series
* - - - -
A8.4.7.14. UARRSI lamp
TR: 1C-17A-2-33JG series
- - - -
A8.4.8. Bench check
A8.5. LANDING GEAR SYSTEM
TR:
- - - -
A8.5.1. Operational fundamentals - - - -
A8.5.2. Operational check
A8.5.2.1. MLG normal sys
TR: 1C-17A-2-32JG series
- - - -
A8.5.2.2. NLG normal sys
TR: 1C-17A-2-32JG series
- - - -
A8.5.2.3. Gear handle electrical interlock system
TR: 1C-17A-2-32JG series
- - - -
- - - -
- - - -
A8.5.3. Troubleshoot
A8.5.3.1. Landing gear sys. using FI manual
TR: 1C-17A-2-32FI-00-1
* - - - -
C-17 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
113Attachment 8
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A8.5.4. Inspect System Components * - - - -
A8.5.5. Remove components
A8.5.5.1. Weight-on-wheels (WOW) proximity sensor
TR: 1C-17A-2-32JG series
- - - -
A8.5.5.2. LG control/indication pnl
TR: 1C-17A-2-32JG series
* - - - -
A8.5.5.3 .Main landing gear downlock proximity sensor
TR: 1C-17A-2-32JG series
- - - -
A8.5.5.4. Main landing gear uplock proximity sensor
TR: 1C-17A-2-32JG series
- - - -
A8.5.5.5. Nose landing gear down proximity sensor
TR: 1C-17A-2-32JG series
- - - -
A8.5.5.6. Nose landing lock proximity sensor
TR: 1C-17A-2-32JG series
- - - -
A8.5.6. Repair components - - - -
A8.5.7. Install components
A8.5.7.1. Weight-on-wheels (WOW) proximity sensor
TR: 1C-17A-2-32JG series
- - - -
A8.5.7.2. LG control/indication pnl
TR: 1C-17A-2-32JG series
* - - - -
A8.5.7.3. Main landing gear downlock proximity sensor
TR: 1C-17A-2-32JG series
- - - -
A8.5.7.4. Main landing gear uplock proximity sensor
TR: 1C-17A-2-32JG series
- - - -
A8.5.7.5. Nose landing gear down proximity sensor
TR: 1C-17A-2-32JG series
- - - -
A8.5.7.6. Nose landing lock proximity sensor
TR: 1C-17A-2-32JG series
- - - -
A8.5.8. Bench check - - - -
A8.6. ANTI-SKID SYSTEM
TR: APPLICABLE AIRCRAFT TO’S
A8.6.1. Operational fundamentals - - - -
A8.6.2. Operational check
A8.6.2.1. Anti-skid sys
TR: 1C-17A-2-32JG series
*R - - - -
A8.6.2.2. Brake pressure indicator
TR: 1C-17A-2-32JG series
- - - -
A8.6.3. Troubleshoot System * - - - -
C-17 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
114Attachment 8
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A8.6.4. Inspect System Components * - - - -
A8.6.5. Remove components
A8.6.5.1. Wheel speed transducer adapter assembly
TR: 1C-17A-2-32JG series
- - - -
A8.6.5.2. Proximity sensor
TR: 1C-17A-2-32JG series
- - - -
A8.6.5.3. Anti-skid/brake temp monitor control unit
TR: 1C-17A-2-32JG series
*R - - - -
A8.6.5.4. Wheel speed transducer
TR: 1C-17A-2-32JG series
* - - - -
A8.6.5.5. Brake temp sensor
TR: 1C-17A-2-32JG series
* - - - -
A8.6.5.6. Brake temp data acquisition unit
TR: 1C-17A-2-32JG series
- - - -
A8.6.5.7. Brake sys pressure gage
TR: 1C-17A-2-32JG series
- - - -
A8.6.5.8. Brake pressure indicator
TR: 1C-17A-2-32JG series
- - - -
A8.6.6. Repair components - - - -
A8.6.7. Install components
A8.6.7.1. Wheel speed transducer adapter assembly
TR: 1C-17A-2-32JG series
- - - -
A8.6.7.2. Proximity sensor
TR: 1C-17A-2-32JG series
- - - -
A8.6.7.3. Anti-skid/brake temp monitor control unit
TR: 1C-17A-2-32JG series
* - - - -
A8.6.7.4. Wheel speed transducer
TR: 1C-17A-2-32JG series
* - - - -
A8.6.7.5. Brake temp sensor
TR: 1C-17A-2-32JG series
* - - - -
A8.6.7.6. Brake temp data acquisition unit
TR: 1C-17A-2-32JG series
- - - -
A8.6.7.7. Brake sys pressure gage
TR: 1C-17A-2-32JG series
- - - -
- - - -
A8.6.7.8. Brake pressure indicator
TR: 1C-17A-2-32JG series
- - - -
A8.6.8. Bench check - - - -
C-17 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
115Attachment 8
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A8.7. PRIMARY FLIGHT CONTROL SYSTEM
A8.7.1. Operational fundamentals - - - -
A8.7.2. Operational check - - - -
A8.7.3. Troubleshoot System - - - -
A8.7.4 .Inspect System Components - - - -
A8.7.5. Remove components - - - -
A8.7.6. Repair components - - - -
A8.7.7. Install components - - - -
A8.7.8. Bench check - - - -
A8.8. SECONDARY FLIGHT CONTROL SYSTEM
TR: APPLICABLE AIRCRAFT TO’S
A8.8.1. Operational fundamentals - - - -
A8.8.2. Operational check - - - -
A8.8.3. Troubleshoot System - - - -
A8.8.4. Inspect System Components - - - -
A8.8.5. Remove components - - - -
A8.8.6. Repair components - - - -
A8.8.7. Install components - - - -
A8.8.8. Bench check - - - -
A8.9. OVERHEAT/FIRE WARNING SYSTEM
TR: APPLICABLE AIRCRAFT TO’S
A8.9.1. Operational fundamentals - - - -
A8.9.2. Operational check
A8.9.2.1. Engine fire system
TR: 1C-17A-2-26JG series
*R - - - -
A8.9.2.2. Accessory compt fire detection assembly
TR: 1C-17A-2-26JG series
- - - -
A8.9.2.3. Firing capability test of APU fire control panel
TR: 1C-17A-2-26JG series
- - - -
A8.9.2.4. Continuity test of APU fire control panel
TR: 1C-17A-2-26JG series
- - - -
A8.9.2.5. Agent low press indicating test of APU fire control panel
TR: 1C-17A-2-26JG series
- - - -
A8.9.2.6. Horn silencing test of APU fire control panel
TR: 1C-17A-2-26JG series
- - - -
A8.9.2.7. Underfloor APU fire warning horn
TR: 1C-17A-2-26JG series
- - - -
C-17 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
116Attachment 8
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A8.9.2.8. Smoke detection sys
TR: 1C-17A-2-26JG series
*R - - - -
A8.9.2.9. Engine firing capability test
TR: 1C-17A-2-26JG series
- - - -
A8.9.2.10. Engine fire continuity test
TR: 1C-17A-2-26JG series
- - - -
A8.9.2.11. Engine fire agent low pressure indicating test
TR: 1C-17A-2-26JG series
- - - -
A8.9.2.12. Firing capability test for APU panels
TR: 1C-17A-2-26JG series
- - - -
A8.9.2.13. Continuity test for APU panels
TR: 1C-17A-2-26JG series
- - - -
A8.9.2.14. Agent low pressure indicating - - - -
A8.9.2.15. Test for APU panel
TR: 1C-17A-2-26JG series
- - - -
A8.9.3. Troubleshoot
A8.9.3.1. Fire protection sys. using FI manual
TR: 1C-17A-2-26FI-00-1
* - - - -
A8.9.4. Inspect System Components * - - - -
A8.9.5. Remove components
A8.9.5.1. Engine fire detector controller
TR: 1C-17A-2-26JG series
*R - - - -
A8.9.5.2. Accessory compartment fire detection assembly
TR: 1C-17A-2-26JG series
- - - -
A8.9.5.3. Eng accessory compt fire detector sensor
TR: 1C-17A-2-26JG series
- - - -
A8.9.5.4. Core compt fire detection assembly
TR: 1C-17A-2-26JG series
- - - -
A8.9.5.5. Eng core compt fire detector Sensor
TR: 1C-17A-2-26JG series
- - - -
A8.9.5.6. Fire control switch handle
TR: 1C-17A-2-26JG series
- - - -
A8.9.5.7. Fire handle incandescent lamp
TR: 1C-17A-2-26JG series
- - - -
A8.9.5.8. APU fire control panel
TR: 1C-17A-2-26JG series
- - - -
A8.9.5.9. Underfloor APU electric fire warning horn
TR: 1C-17A-2-26JG series
- - - -
C-17 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
117Attachment 8
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A8.9.5.10. APU fire detector controller
TR: 1C-17A-2-26JG series
* - - - -
A8.9.5.11. APU fire detection assembly
TR: 1C-17A-2-26JG series
- - - -
A8.9.5.12. Fire detector sensor on APU
TR: 1C-17A-2-26JG series
- - - -
A8.9.5.13. Cargo floor smoke detector indicator panel
TR: 1C-17A-2-26JG series
* - - - -
A8.9.5.14. Cargo compt curb smoke detectors (opaque particle)
TR: 1C-17A-2-26JG series
*R - - - -
A8.9.5.15. Cargo compt ceiling smoke detectors
TR: 1C-17A-2-26JG series
*R - - - -
A8.9.5.16. Lavatory smoke detector
TR: 1C-17A-2-26JG series
*R - - - -
A8.9.5.17. Crew rest smoke detector
TR: 1C-17A-2-26JG series
*R - - - -
A8.9.5.18. Avionics compt smoke detector
TR: 1C-17A-2-26JG series
*R - - - -
A8.9.5.19. Lower avionics rack inertial ref unit smoke detector
TR: 1C-17A-2-26JG series
*R - - - -
A8.9.5.20 Inertial ref unit rack smoke detector
TR: 1C-17A-2-26JG series
*R - - - -
A8.9.5.21. Engine fire ext discharge cartridge
TR: 1C-17A-2-26JG series
*R - - - -
A8.9.5.22. Engine fire extinguisher container
TR: 1C-17A-2-26JG series
- - - -
A8.9.5.23. Engine fire extinguisher discharge head
TR: 1C-17A-2-26JG series
- - - -
A8.9.5.24. Engine fire fuel shutoff gate valve
TR: 1C-17A-2-26JG series
- - - -
A8.9.5.25. Engine fire fuel shutoff gate valve actuator
TR: 1C-17A-2-26JG series
- - - -
A8.9.5.26. Engine hydraulic shutoff ball valve
TR: 1C-17A-2-26JG series
- - - -
A8.9.5.27. APU fire ext discharge cartridge
TR: 1C-17A-2-26JG series
*R - - - -
A8.9.5.28. APU fire extinguisher container
TR: 1C-17A-2-26JG series
- - - -
C-17 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
118Attachment 8
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A8.9.5.29. Portable fire extinguisher
TR: 1C-17A-2-26JG series
- - - -
A8.9.6. Repair components - - - -
A8.9.7. Install components
A8.9.7.1. Engine fire detector controller
TR: 1C-17A-2-26JG series
*R - - - -
A8.9.7.2 .Accessory compartment fire detection assembly
TR: 1C-17A-2-26JG series
- - - -
A8.9.7.3. Eng accessory compt fire detector sensor
TR: 1C-17A-2-26JG series
- - - -
A8.9.7.4. Core compt fire detection assembly
TR: 1C-17A-2-26JG series
- - - -
A8.9.7.5. Eng core compt fire detector sensor
TR: 1C-17A-2-26JG series
- - - -
A8.9.7.6. Fire control switch handle
TR: 1C-17A-2-26JG series
- - - -
A8.9.7.7. Fire handle incandescent lamp
TR: 1C-17A-2-26JG series
- - - -
A8.9.7.8. APU fire control panel
TR: 1C-17A-2-26JG series
- - - -
A8.9.7.9. Underfloor APU electric fire warning horn
TR: 1C-17A-2-26JG series
- - - -
A8.9.7.10. APU fire detector controller
TR: 1C-17A-2-26JG series
* - - - -
A8.9.7.11. APU fire detection assembly
TR: 1C-17A-2-26JG series
- - - -
A8.9.7.12. Fire detector sensor on APU
TR: 1C-17A-2-26JG series
- - - -
A8.9.7.13. Cargo floor smoke detector indicator panel
TR: 1C-17A-2-26JG series
* - - - -
A8.9.7.14. Cargo compt curb smoke detectors (opaque particle)
TR: 1C-17A-2-26JG series
*R - - - -
A8.9.7.15. Cargo compt ceiling smoke detectors
TR: 1C-17A-2-26JG series
*R - - - -
A8.9.7.16. Lavatory smoke detector
TR: 1C-17A-2-26JG series
*R - - - -
A8.9.7.17. Crew rest smoke detector
TR: 1C-17A-2-26JG series
*R - - - -
C-17 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
119Attachment 8
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A8.9.7.18. Avionics compt smoke detector
TR: 1C-17A-2-26JG series
*R - - - -
A8.9.7.19. Lower avionics rack inertial ref unit smoke detector
TR: 1C-17A-2-26JG series
*R - - - -
A8.9.7.20. Inertial ref unit rack smoke detector
TR: 1C-17A-2-26JG series
*R - - - -
A8.9.7.21. Engine fire ext discharge cartridge
TR: 1C-17A-2-26JG series
*R - - - -
A8.9.7.22. Engine fire extinguisher container
TR: 1C-17A-2-26JG series
- - - -
A8.9.7.23. Engine fire extinguisher discharge head
TR: 1C-17A-2-26JG series
- - - -
A8.9.7.24. Engine fire fuel shutoff gate valve
TR: 1C-17A-2-26JG series
- - - -
A8.9.7.25. Engine fire fuel shutoff gate valve actuator
TR: 1C-17A-2-26JG series
- - - -
A8.9.7.26. Engine hydraulic shutoff ball valve
TR: 1C-17A-2-26JG series
- - - -
A8.9.7.27. APU fire ext discharge cartridge
TR: 1C-17A-2-26JG series
*R - - - -
A8.9.7.28. APU fire extinguisher container
TR: 1C-17A-2-26JG series
- - - -
A8.9.7.29. Portable fire extinguisher
TR: 1C-17A-2-26JG series
- - - -
A8.9.8. Bench check - - - -
A8.10 ICE AND RAIN PROTECTION SYSTEM
TR: 1C-17A-2-30 SERIES
A8.10.1. Operational fundamentals - - - -
A8.10.2. Operational check
A8.10.2.1. Airfoil and air intakes
TR: 1C-17A-2-30JG series
- - - -
A8.10.2.2. Windows and windshield
TR: 1C-17A-2-30JG series
*R - - - -
A8.10.3. Troubleshoot
A8.10.3.1. Ice & rain protection sys. using FI manual
TR: 1C-17A-2-30FI-00-1
* - - - -
A8.10.4. Inspect System Components * - - - -
A8.10.5. Remove components
C-17 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
120Attachment 8
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A8.10.5.1. Anti-ice control panel assembly
TR: 1C-17A-2-30JG series
- - - -
A8.10.5.2. Wing anti-ice shutoff valve
TR: 1C-17A-2-30JG series
- - - -
A8.10.5.3. Wing slat number two anti-ice telescopic duct
TR: 1C-17A-2-30JG series
- - - -
A8.10.5.4. Wing slat number three anti-ice telescopic duct
TR: 1C-17A-2-30JG series
- - - -
A8.10.5.5. Wing slat number four anti-ice telescopic duct
TR: 1C-17A-2-30JG series
- - - -
A8.10.5.6. Wing anti-ice low temperature sensor
TR: 1C-17A-2-30JG series
- - - -
A8.10.5.7. XFS 853 to 896 leading edge slat 4 anti ice duct assembly
TR: 1C-17A-2-30JG series
- - - -
A8.10.5.8. XFS 818 to 853 leading edge slat outbd anti-ice ductassembly
TR: 1C-17A-2-30JG series
- - - -
A8.10.5.9. XFS 772 to 818 leading edge slat outbd wing anti-ice duct assembly
TR: 1C-17A-2-30JG series
- - - -
A8.10.5.10. XFS 730 to 772 leading edge slat outbd wing anti-iceduct assembly
TR: 1C-17A-2-30JG series
- - - -
A8.10.5.11. XFS 692 to 730 leading edge slat outbd wing anti-iceduct assembly
TR: 1C-17A-2-30JG series
- - - -
A8.10.5.12. XFS 651 to 682 leading edge anti-ice elbow duct assembly
TR: 1C-17A-2-30JG series
- - - -
A8.10.5.13. XFS 620 to 651 leading edge anti-ice flexible duct assembly
TR: 1C-17A-2-30JG series
- - - -
A8.10.5.14. XFS 602 to 651 leading edge anti-ice tee duct assembly
TR: 1C-17A-2-30JG series
- - - -
A8.10.5.15. XFS 569 to 609 leading edge anti-ice flexible elbow duct assembly
TR: 1C-17A-2-30JG series
- - - -
A8.10.5.16. XFS 576 to 597 leading edge anti-ice venturi duct assembly
TR: 1C-17A-2-30JG series
- - - -
C-17 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
121Attachment 8
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A8.10.5.17. XFS 510 to 569 leading edge slat number 2 outbd anti-ice duct
TR: 1C-17A-2-30JG series
- - - -
A8.10.5.18. XFS 477 to 510 anti-ice duct assembly
TR: 1C-17A-2-30JG series
- - - -
A8.10.5.19. 430 to 477 leading edge eng wing bleed air duct assembly
TR: 1C-17A-2-30JG series
- - - -
A8.10.5.20. 416 to 430 slat 2 leading edge anti-ice duct assembly
TR: 1C-17A-2-30JG series
- - - -
A8.10.5.21. Engine cowl anti-ice low temperature sensor
TR: 1C-17A-2-30JG series
- - - -
A8.10.5.22. Engine cowl anti-ice venturi duct assembly
TR: 1C-17A-2-30JG series
- - - -
A8.10.5.23. Windshield anti-ice controller
TR: 1C-17A-2-30JG series
*R - - - -
A8.10.5.24. Window defog controller
TR: 1C-17A-2-30JG series
*R - - - -
A8.10.6. Repair components - - - -
A8.10.7. Install components
A8.10.7.1. Anti-ice control panel assembly
TR: 1C-17A-2-30JG series
- - - -
A8.10.7.2. Wing anti-ice shutoff valve
TR: 1C-17A-2-30JG series
- - - -
A8.10.7.3. Wing slat number two anti-ice telescopic duct
TR: 1C-17A-2-30JG series
- - - -
A8.10.7.4. Wing slat number three anti-ice telescopic duct
TR: 1C-17A-2-30JG series
- - - -
A8.10.7.5. Wing slat number four anti-ice telescopic duct
TR: 1C-17A-2-30JG series
- - - -
A8.10.7.6. Wing anti-ice low temperature sensor
TR: 1C-17A-2-30JG series
- - - -
A8.10.7.7. XFS 853 to 896 leading edge slat 4 anti ice duct assembly
TR: 1C-17A-2-30JG series
- - - -
A8.10.7.8. XFS 818 to 853 leading edge slat outbd anti-ice duct assembly
TR: 1C-17A-2-30JG series
- - - -
A8.10.7.9. XFS 772 to 818 leading edge slat outbd wing anti-ice duct assembly
- - - -
C-17 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
122Attachment 8
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
TR: 1C-17A-2-30JG series
A8.10.7.10. XFS 730 to 772 leading edge slat outbd wing anti-iceduct assembly
TR: 1C-17A-2-30JG series
- - - -
A8.10.7.11. XFS 692 to 730 leading edge slat outbd wing anti-ice duct assembly
TR: 1C-17A-2-30JG series
- - - -
A8.10.7.12. XFS 651 to 682 leading edge anti-ice elbow duct assembly
TR: 1C-17A-2-30JG series
- - - -
A8.10.7.13. XFS 620 to 651 leading edge edge anti-ice flexibleduct assembly
TR: 1C-17A-2-30JG series
- - - -
A8.10.7.14. XFS 602 to 651 leading edge anti-ice tee duct assembly
TR: 1C-17A-2-30JG series
- - - -
A8.10.7.15. XFS 569 to 609 leading edge edge anti-ice flexible elbow duct assembly
TR: 1C-17A-2-30JG series
- - - -
A8.10.7.16. XFS 576 to 597 leading edge edge anti-ice venturiduct assembly
TR: 1C-17A-2-30JG series
- - - -
A8.10.7.17. XFS 510 to 569 leading edge slat number 2 outbd anti-ice duct
TR: 1C-17A-2-30JG series
- - - -
A8.10.7.18. XFS 477 to 510 anti-ice duct assembly
TR: 1C-17A-2-30JG series
- - - -
A8.10.7.19. 430 to 477 leading edge eng wing bleed air duct assembly
TR: 1C-17A-2-30JG series
- - - -
A8.10.7.20. 416 to 430 slat 2 leading edge anti-ice duct assembly
TR: 1C-17A-2-30JG series
- - - -
A8.10.7.21. Engine cowl edge anti-ice low temperature sensor
TR: 1C-17A-2-30JG series
- - - -
A8.10.7.22. Engine cowl anti-ice venturi duct assembly
TR: 1C-17A-2-30JG series
- - - -
A8.10.7.23. Windshield anti-ice controller
TR: 1C-17A-2-30JG series
*R - - - -
A8.10.7.24. Window defog controller
TR: 1C-17A-2-30JG series
*R - - - -
A8.10.8. Bench check - - - -
A8.11. ONBOARD INERT GAS GENERATION SYSTEM
C-17 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
123Attachment 8
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
(OBIGGS)
TR: 1C-17A-2-47 SERIES
A8.11.1. Operational fundamentals - - - -
A8.11.2. Operational check
A8.11.2.1. Onboard inert gas generation system
TR: 1C-C17A-2-47JG-00-1
* - - - -
A8.11.2.2 .Interrogation onboard inert gas generation system
TR: 1C-C17A-2-47JG-00-1
* - - - -
A8.11.2.3 .Air separation module
TR: 1C-C17A-2-47JG-10-1
- - - -
A8.11.2.4. Crossfeed bleed air shutoff valve
TR: 1C-C17A-2-47JG-10-1
- - - -
A8.11.2.5. APU bleed air shutoff valve
TR: 1C-C17A-2-47JG-10-1
- - - -
A8.11.2.6. Distribution crossfeed valve
TR: 1C-C17A-2-47JG-20-1
- - - -
A8.11.3. Troubleshoot
A8.11.3.1 .Inert (OBIGGS) sys using FI manual
TR: 1C-C17A-2-47FI-00-1
* - - - -
A8.11.4. Inspect System Components * - - - -
A8.11.5. Remove components
A8.11.5.1. Inflow check valve
TR: 1C-C17A-2-47JG-10-1
- - - -
A8.11.5.2. Ducts associated with overheat sensing elements
TR: 1C-C17A-2-47JG-10-1
- - - -
A8.11.5.3. Precooler
TR: 1C-C17A-2-47JG-10-1
- - - -
A8.11.5.4. Air separation module
TR: 1C-C17A-2-47JG-10-1
* - - - -
A8.11.5.5. Air separation module air filter
TR: 1C-C17A-2-47JG-10-1
*R - - - -
A8.11.5.6. Air compressor
TR: 1C-C17A-2-47JG-10-1
* - - - -
A8.11.5.7. Air compressor air filter
TR: 1C-C17A-2-47JG-10-1
- - - -
A8.11.5.8. Air compressor filter element
TR: 1C-C17A-2-47JG-10-1
- - - -
A8.11.5.9. Bleed air pressure regulator valve *R - - - -
C-17 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
124Attachment 8
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
TR: 1C-C17A-2-47JG-10-1
A8.11.5.10. Bleed air overpressure valve
TR: 1C-C17A-2-47JG-10-1
*R - - - -
A8.11.5.11. Cooling air control valve
TR: 1C-C17A-2-47JG-10-1
- - - -
A8.11.5.12. Bleed air check valve
TR: 1C-C17A-2-47JG-10-1
- - - -
A8.11.5.13. Crossfeed bleed air shutoff valve
TR: 1C-C17A-2-47JG-10-1
- - - -
A8.11.5.14. Supply shutoff valve
TR: 1C-C17A-2-47JG-10-1
- - - -
A8.11.5.15. Fluid purity controller
TR: 1C-C17A-2-47JG-10-1
* - - - -
A8.11.5.16. Heat exchanger
TR: 1C-C17A-2-47JG-10-1
- - - -
A8.11.5.17. Heat exchanger bypass valve
TR: 1C-C17A-2-47JG-10-1
- - - -
A8.11.5.18. Temperature sensitive element
TR: 1C-C17A-2-47JG-10-1
- - - -
A8.11.5.19. Remote mount solenoid pilot valve unit
TR: 1C-C17A-2-47JG-10-1
- - - -
A8.11.5.20. Wheel pod temperature sensitive element
TR: 1C-C17A-2-47JG-10-1
- - - -
A8.11.5.21. Pressure transmitter
TR: 1C-C17A-2-47JG-10-1
- - - -
A8.11.5.22. Distribution crossfeed valve
TR: 1C-C17A-2-47JG-20-1
- - - -
A8.11.5.23. High pressure regulating valve
TR: 1C-C17A-2-47JG-20-1
- - - -
A8.11.5.24. Low pressure regulating valve
TR: 1C-C17A-2-47JG-20-1
- - - -
A8.11.5.25. Double relief valve
TR: 1C-C17A-2-47JG-20-1
- - - -
A8.11.5.26. High pressure relief valve
TR: 1C-C17A-2-47JG-20-1
- - - -
A8.11.5.27. Rupture disk
TR: 1C-C17A-2-47JG-20-1
- - - -
A8.11.5.28. Nitrogen storage tank pressure gauge - - - -
C-17 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
125Attachment 8
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
TR: 1C-C17A-2-47JG-40-1
A8.11.5.29. Overheat detector sensing element
TR: 1C-C17A-2-47JG-40-1
- - - -
A8.11.5.30. OBIGGS system precooler outlet grille
TR: 1C-C17A-2-54JG-60-1
- - - -
A8.11.5.31. Pressure transmitter
TR: 1C-C17A-2-47JG-40-1
- - - -
A8.11.6. Repair components - - - -
A8.11.7. Install components
A8.11.7.1. Inflow check valve
TR: 1C-C17A-2-47JG-10-1
- - - -
A8.11.7.2. Ducts associated with overheat sensing elements
TR: 1C-C17A-2-47JG-10-1
- - - -
A8.11.7.3. Precooler
TR: 1C-C17A-2-47JG-10-1
- - - -
A8.11.7.4. Air separation module
TR: 1C-C17A-2-47JG-10-1
* - - - -
A8.11.7.5. Air separation module air filter
TR: 1C-C17A-2-47JG-10-1
*R - - - -
A8.11.7.6. Air compressor
TR: 1C-C17A-2-47JG-10-1
* - - - -
A8.11.7.7. Air compressor air filter
TR: 1C-C17A-2-47JG-10-1
- - - -
A8.11.7.8. Air compressor filter element
TR: 1C-C17A-2-47JG-10-1
- - - -
A8.11.7.9. Bleed air pressure regulator valve
TR: 1C-C17A-2-47JG-10-1
* - - - -
A8.11.7.10. Bleed air overpressure valve
TR: 1C-C17A-2-47JG-10-1
*R - - - -
A8.11.7.11. Cooling air control valve
TR: 1C-C17A-2-47JG-10-1
- - - -
A8.11.7.12. Bleed air check valve
TR: 1C-C17A-2-47JG-10-1
- - - -
A8.11.7.13. Crossfeed bleed air shutoff valve
TR: 1C-C17A-2-47JG-10-1
- - - -
A8.11.7.14. Supply shutoff valve
TR: 1C-C17A-2-47JG-10-1
- - - -
A8.11.7.15. Fluid purity controller * - - - -
C-17 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
126Attachment 8
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
TR: 1C-C17A-2-47JG-10-1
A8.11.7.16. Heat exchanger
TR: 1C-C17A-2-47JG-10-1
- - - -
A8.11.7.17. Heat exchanger bypass valve
TR: 1C-C17A-2-47JG-10-1
- - - -
A8.11.7.18. Temperature sensitive element
TR: 1C-C17A-2-47JG-10-1
- - - -
A8.11.7.19. Remote mount solenoid pilot valve unit
TR: 1C-C17A-2-47JG-10-1
- - - -
A8.11.7.20. Wheel pod temperature sensitive element
TR: 1C-C17A-2-47JG-10-1
- - - -
A8.11.7.21. Pressure transmitter
TR: 1C-C17A-2-47JG-10-1
- - - -
A8.11.7.22. Distribution crossfeed valve
TR: 1C-C17A-2-47JG-20-1
- - - -
A8.11.7.23. High pressure regulating valve
TR: 1C-C17A-2-47JG-20-1
- - - -
A8.11.7.24. Low pressure regulating valve
TR: 1C-C17A-2-47JG-20-1
- - - -
A8.11.7.25. Double relief valve
TR: 1C-C17A-2-47JG-20-1
- - - -
A8.11.7.26. High pressure relief valve
TR: 1C-C17A-2-47JG-20-1
- - - -
A8.11.7.27. Rupture disk
TR: 1C-C17A-2-47JG-20-1
- - - -
A8.11.7.28. Nitrogen storage tank pressure gauge
TR: 1C-C17A-2-47JG-40-1
- - - -
A8.11.7.29. Overheat detector sensing element
TR: 1C-C17A-2-47JG-40-1
- - - -
A8.11.7.30. OBIGGS system precooler outlet grille
TR: 1C-C17A-2-54JG-60-1
- - - -
A8.11.7.31. Pressure transmitter
TR: 1C-C17A-2-47JG-40-1
- - - -
A8.11.8. Bench check - - - -
A8.11.9. Drain OBIGGS Sys.
TR: 1C-17A-2-12JG series
* - - - -
A8.11.10. Service OBIGGS Sys.
TR: 1C-17A-2-12JG series
*R - - - -
C-17 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
127Attachment 8
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A8.12. INDICATING & RECORDING SYSTEM
TR: 1C-17A-2-31 SERIES
A8.12.1. Operational fundamentals - - - -
A8.12.2. Operational check
A8.12.2.1. Proximity sensing system
TR: 1C-17A-2-31JG series
- - - -
A8.12.2.2. Sensor signal interface unit to view/erase faults
TR: 1C-17A-2-31JG series
* - - - -
A8.12.2.3. Aural warning sys
TR: 1C-17A-2-31JG series
- - - -
A8.12.2.4. Visual warning & caution sys
TR: 1C-17A-2-31JG series
- - - -
A8.12.2.5. Multifunction display sys (MFD)
TR: 1C-17A-2-31JG series
*R - - - -
A8.12.3. Troubleshoot
A8.12.3.1. Indicating & recording sys. using FI manual
TR: 1C-17A-2-31FI-00-1
*R - - - -
A8.12.4 .Inspect System Components *R - - - -
A8.12.5. Remove components
A8.12.5.1. Warning & caution computer (WACC)
TR: 1C-17A-2-31JG series
* - - - -
A8.12.5.2. Warning & caution annunciator panel (WAP)
TR: 1C-17A-2-31JG series
*R - - - -
A8.12.5.3. Sensor signal interface Unit
TR: 1C-17A-2-31JG series
* - - - -
A8.12.6. Repair components
A8.12.6.1. Warning & caution annunciator panel (WAP)
TR: 1C-17A-2-31JG series
- - - -
A8.12.6.2 WCC Data bus line - - - -
A8.12.7. Install components
A8.12.7.1. Warning & caution computer (WACC)
TR: 1C-17A-2-31JG series
* - - - -
A8.12.7.2. Warning & caution annunciator panel (WAP)
TR: 1C-17A-2-31JG series
*R - - - -
A8.12.7.3. Sensor signal interface unit
TR: 1C-17A-2-31JG series
* - - - -
A8.12.8. Bench check - - - -
A8.13. DOOR CONTROL AND WARNING SYSTEM
C-17 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
128Attachment 8
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
TR: 1C-17A-2-52JG SERIES
A8.13.1. Operational fundamentals - - - -
A8.13.2. Operational check
A8.13.2.1. Door actuating & indicating sys
TR: 1C-17A-2-28JG series
- - - -
A8.13.2.2. Open/close cargo ramp/door automatically
TR: 1C-C17A-2-52JG-30-1
- - - -
A8.13.2.3. Open/close cargo ramp/door manually
TR: 1C-C17A-2-52JG-30-1
- - - -
A8.13.3. Troubleshoot
A8.13.3.1. Door sys using FI manual
TR: 1C-C17A-2-52FI-00-1
* - - - -
A8.13.4. Inspect System Components * - - - -
A8.13.5. Remove components
A8.13.5.1. Cargo door uplock prox sensor
TR: 1C-C17A-2-52JG-30-1
- - - -
A8.13.5.2. Cargo door position transmitter
TR: 1C-C17A-2-52JG-30-1
- - - -
A8.13.5.3. Cargo ramp up limit prox sensor
TR: 1C-C17A-2-52JG-30-1
- - - -
A8.13.5.4. ADS link prox sensor
TR: 1C-C17A-2-52JG-30-1
- - - -
A8.13.5.5. Cargo ramp prox sensor
TR: 1C-C17A-2-52JG-30-1
- - - -
A8.13.5.6. Cargo ramp actuating cylinder
TR: 1C-C17A-2-52JG-30-1
- - - -
A8.13.5.7. Door/status pnl
TR: 1C-C17A-2-52JG-70-1
- - - -
A8.13.5.8. Crew door prox sensor
TR: 1C-C17A-2-52JG-70-1
- - - -
A8.13.5.9. Crew door down/locked prox sensor
TR: 1C-C17A-2-52JG-70-1
- - - -
A8.13.5.10. Emergency exit door prox sensor
TR: 1C-C17A-2-52JG-70-1
- - - -
A8.13.5.11. Maint/ditch access door prox sensor
TR: 1C-C17A-2-52JG-70-1
- - - -
A8.13.5.12. Maint (tunnel) access door prox sensor
TR: 1C-C17A-2-52JG-70-1
- - - -
C-17 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
129Attachment 8
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A8.13.5.13. Side equipment access door prox sensor
TR: 1C-C17A-2-52JG-70-1
- - - -
A8.13.5.14. Vert stab (tunnel) access door prox sensor
TR: 1C-C17A-2-52JG-70-1
- - - -
A8.13.5.15. Horizontal stab access door prox sensor
TR: 1C-C17A-2-52JG-70-1
- - - -
A8.13.5.16. Ram air turbine door prox sensor
TR: 1C-C17A-2-52JG-70-1
- - - -
A8.13.5.17. Cargo ramp locked prox sensor
TR: 1C-C17A-2-52JG-70-1
- - - -
A8.13.5.18. Troop door air deflector prox sensor
TR: 1C-C17A-2-52JG-70-1
- - - -
A8.13.5.19. Troop door prox sensor
TR: 1C-C17A-2-52JG-70-1
- - - -
A8.13.6. Repair components - - - -
A8.13.7. Install components
A8.13.7.1. Cargo door uplock prox sensor
TR: 1C-C17A-2-52JG-30-1
- - - -
A8.13.7.2. Cargo door position transmitter
TR: 1C-C17A-2-52JG-30-1
- - - -
A8.13.7.3. Cargo ramp up limit prox sensor
TR: 1C-C17A-2-52JG-30-1
- - - -
A8.13.7.4. ADS link prox sensor
TR: 1C-C17A-2-52JG-30-1
- - - -
A8.13.7.5. Cargo ramp prox sensor
TR: 1C-C17A-2-52JG-30-1
- - - -
A8.13.7.6. Cargo ramp actuating cylinder
TR: 1C-C17A-2-52JG-30-1
- - - -
A8.13.7.7. Door/status pnl
TR: 1C-C17A-2-52JG-70-1
- - - -
A8.13.7.8. Crew door prox sensor
TR: 1C-C17A-2-52JG-70-1
- - - -
A8.13.7.9. Crew door down/locked prox sensor
TR: 1C-C17A-2-52JG-70-1
- - - -
A8.13.7.10. Emergency exit door prox sensor
TR: 1C-C17A-2-52JG-70-1
- - - -
A8.13.7.11. Maint/ditch access door prox sensor
TR: 1C-C17A-2-52JG-70-1
- - - -
C-17 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
130Attachment 8
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A8.13.7.12. Maint (tunnel) access door prox sensor
TR: 1C-C17A-2-52JG-70-1
- - - -
A8.13.7.13. Side equipment access door prox sensor
TR: 1C-C17A-2-52JG-70-1
- - - -
A8.13.7.14. Vert stab (tunnel) access door prox sensor
TR: 1C-C17A-2-52JG-70-1
- - - -
A8.13.7.15. Horizontal stab access door prox sensor
TR: 1C-C17A-2-52JG-70-1
- - - -
A8.13.7.16. Ram air turbine door prox sensor
TR: 1C-C17A-2-52JG-70-1
- - - -
A8.13.7.17. Cargo ramp locked prox sensor
TR: 1C-C17A-2-52JG-70-1
- - - -
A8.13.7.18. Troop door air deflector prox sensor
TR: 1C-C17A-2-52JG-70-1
- - - -
A8.13.7.19. Troop door prox sensor
TR: 1C-C17A-2-52JG-70-1
- - - -
A8.13.8. Bench check - - - -
A8.14. CARGO HANDLING/MISSION SYSTEM
TR: 1C-17A-2-41 SERIES
A8.14.1. Operational fundamentals - - - -
A8.14.2. Operational check
A8.14.2.1. Door actuating & indicating sys
TR: 1C-17A-2-28JG series
- - - -
A8.14.2.2. Ads locks control pnl
TR: 1C-C17A-2-41JG-10-1
- - - -
A8.14.2.3. Variable restraint assembly
TR: 1C-C17A-2-41JG-10-1
- - - -
A8.14.2.4. Cargo compartment logistic pallet control pnl
TR: 1C-C17A-2-41JG-10-1
- - - -
A8.14.2.5. Support/stab strut sys
TR: 1C-C17A-2-41JG-20-1
- - - -
A8.14.2.6. Cargo winch sys
TR: 1C-C17A-2-41JG-20-1
- - - -
A8.14.2.7. CDS sys
TR: 1C-C17A-2-41JG-30-1
- - - -
A8.14.2.8. Tow release mechanism
TR: 1C-C17A-2-41JG-30-1
- - - -
A8.14.2.9. Parachute deployment mechanism - - - -
C-17 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
131Attachment 8
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
TR: 1C-C17A-2-41JG-30-1
A8.14.2.10. ADS control panel
TR: 1C-C17A-2-41JG-50-1
- - - -
A8.14.2.11. Forward loadmaster control panel
TR: 1C-C17A-2-41JG-50-1
- - - -
A8.14.2.12. ADS backup control panel
TR: 1C-C17A-2-41JG-50-1
- - - -
A8.14.2.13. Aft loadmaster control panel
TR: 1C-C17A-2-41JG-50-1
- - - -
A8.14.2.14. ADS controller
TR: 1C-C17A-2-41JG-50-1
- - - -
A8.14.2.15. Operate support/stab strut for maint
TR: 1C-C17A-2-41JG-20-1
- - - -
A8.14.2.16. Operate parachute deployment automatic
TR: 1C-C17A-2-41JG-30-1
- - - -
A8.14.2.17. Operate support/stab strut for cargo
TR: 1C-C17A-2-41JG-20-1
- - - -
A8.14.3. Troubleshoot
A8.14.3.1. Cargo handling/mission sys using FI manual
TR: 1C-C17A-2-41FI-00-1
*R - - - -
A8.14.4. Inspect System Components *R - - - -
A8.14.5. Remove components
A8.14.5.1. ADS locks control pnl
TR: 1C-C17A-2-41JG-10-1
- - - -
A8.14.5.2. Cargo compartment logistic pallet control pnl
TR: 1C-C17A-2-41JG-10-1
- - - -
A8.14.5.3. Target switch
TR: 1C-C17A-2-41JG-20-1
- - - -
A8.14.5.4. Up prox sensor
TR: 1C-C17A-2-41JG-20-1
- - - -
A8.14.5.5. Vertical prox sensor
TR: 1C-C17A-2-41JG-20-1
- - - -
A8.14.5.6. Stab strut door actuator plunger switch
TR: 1C-C17A-2-41JG-20-1
- - - -
A8.14.5.7. Tow plate armed prox sensor
TR: 1C-C17A-2-41JG-30-1
- - - -
A8.14.5.8. Drogue chute deployed prox sensor
TR: 1C-C17A-2-41JG-30-1
- - - -
C-17 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
132Attachment 8
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A8.14.5.9. Pendant control
TR: 1C-C17A-2-41JG-40-1
- - - -
A8.14.5.10. Pilot/copilot ADS control panel assembly
TR: 1C-C17A-2-41JG-50-1
- - - -
A8.14.5.11. Forward loadmaster control panel assembly
TR: 1C-C17A-2-41JG-50-1
- - - -
A8.14.5.12. ADS backup control panel assembly
TR: 1C-C17A-2-41JG-50-1
- - - -
A8.14.5.13. Aft loadmaster control panel assembly
TR: 1C-C17A-2-41JG-50-1
- - - -
A8.14.5.14. Forward loadmaster winch control panel
TR: 1C-C17A-2-41JG-50-1
- - - -
A8.14.5.15. Aft loadmaster winch control panel
TR: 1C-C17A-2-41JG-50-1
- - - -
A8.14.5.16. ADS controller
TR: 1C-C17A-2-41JG-50-1
- - - -
A8.14.5.17. ADS controller cooling fan
TR: 1C-C17A-2-41JG-50-1
- - - -
A8.14.5.18. Patient monitoring panel
TR: 1C-C17A-2-41JG-60-1
- - - -
A8.14.5.19. Tow severance assembly * - - - -
A8.14.6. Repair components
A8.14.7. Install components
A8.14.7.1. ADS locks control pnl
TR: 1C-C17A-2-41JG-10-1
- - - -
A8.14.7.2. Cargo compartment logistic pallet control pnl
TR: 1C-C17A-2-41JG-10-1
- - - -
A8.14.7.3. Target switch
TR: 1C-C17A-2-41JG-20-1
- - - -
A8.14.7.4. Up prox sensor
TR: 1C-C17A-2-41JG-20-1
- - - -
A8.14.7.5. Vertical prox sensor
TR: 1C-C17A-2-41JG-20-1
- - - -
A8.14.7.6. Stab strut door actuator plunger switch
TR: 1C-C17A-2-41JG-20-1
- - - -
A8.14.7.7. Tow plate armed prox sensor
TR: 1C-C17A-2-41JG-30-1
- - - -
A8.14.7.8. Drogue chute deployed prox sensor - - - -
C-17 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
133Attachment 8
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
TR: 1C-C17A-2-41JG-30-1
A8.14.7.9. Pendant control
TR: 1C-C17A-2-41JG-40-1
- - - -
A8.14.7.10. Pilot/copilot ADS control panel assembly
TR: 1C-C17A-2-41JG-50-1
- - - -
A8.14.7.11. Forward loadmaster control panel assembly
TR: 1C-C17A-2-41JG-50-1
- - - -
A8.14.7.12. ADS backup control panel assembly
TR: 1C-C17A-2-41JG-50-1
- - - -
A8.14.7.13. Aft loadmaster control panel assembly
TR: 1C-C17A-2-41JG-50-1
- - - -
A8.14.7.14. Forward loadmaster winch control panel
TR: 1C-C17A-2-41JG-50-1
- - - -
A8.14.7.15. Aft loadmaster winch control panel
TR: 1C-C17A-2-41JG-50-1
- - - -
A8.14.7.16. ADS controller
TR: 1C-C17A-2-41JG-50-1
- - - -
A8.14.7.17. ADS controller cooling fan
TR: 1C-C17A-2-41JG-50-1
- - - -
A8.14.7.18. Patient monitoring panel
TR: 1C-C17A-2-41JG-60-1
- - - -
A8.14.7.19. Tow severance assembly * - - - -
A8.14.8. Bench check - - - -
A8.15. FUEL WARNING AND CONTROL SYSTEM
TR: APPLICABLE AIRCRAFT TO’S
A8.15.1. Operational fundamentals - - - -
A8.15.2. Operational check
A8.15.2.1. Inert control panel
TR: 1C-17A-2-28JG series
- - - -
A8.15.2.2. Refueling & defueling sys
TR: 1C-17A-2-28JG series
- - - -
A8.15.2.3. Ground refueling control panel
TR: 1C-17A-2-28JG series
- - - -
A8.15.2.4. Engine start fuel sys control panel
TR: 1C-17A-2-28JG series
- - - -
A8.15.2.5. APU fuel fire shutoff valve
TR: 1C-17A-2-28JG series
- - - -
A8.15.3. Troubleshoot
C-17 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
134Attachment 8
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A8.15.3.1. Fuel Sys using FI manual
TR: 1C-17A2-28FI-00-1
*R - - - -
A8.15.4. Inspect System Components *R - - - -
A8.15.5. Remove components
A8.15.5.1. Check inert control panel
TR: 1C-17A-2-28JG series
- - - -
A8.15.5.2. Ground refueling control panel
TR: 1C-17A-2-28JG series
- - - -
A8.15.5.3. Engine start fuel sys control panel
TR: 1C-17A-2-28JG series
*R - - - -
A8.15.6. Repair components - - - -
A8.15.7. Install components
A8.15.7.1. Check inert control panel
TR: 1C-17A-2-28JG series
- - - -
A8.15.7.2. Ground refueling control panel
TR: 1C-17A-2-28JG series
- - - -
A8.15.7.3. Engine start fuel sys control panel
TR: 1C-17A-2-28JG series
*R - - - -
A8.15.8. Bench check - - - -
A8.16. START AND IGNITION SYSTEM
TR: APPLICABLE AIRCRAFT TO’S
A8.16.1. Operational fundamentals - - - -
A8.16.2. Operational check - - - -
A8.16.3. Troubleshoot
A8.16.3.1. Powerplant start system using FI manual
TR: 1C-C17A-2-80FI-00-1
*R - - - -
A8.16.4. Inspect System Components *R - - - -
A8.16.5. Remove components - - - -
A8.16.6. Repair components - - - -
A8.16.7. Install components - - - -
A8.16.8. Bench check - - - -
A8.17. BLEED AIR DISTRIBUTION SYSTEM
TR: APPLICABLE AIRCRAFT TO’S
A8.17.1 Operational fundamentals - - - -
A8.17.2. Operational check
A8.17.2.1. Interrogation of manifold failure detection controller
TR: 1C-C17A-2-36JG-20-1
* - - - -
A8.17.3. Troubleshoot
C-17 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
135Attachment 8
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A8.17.3.1. Pneumatic sys. using FI manual
TR: 1C-17A-2-36FI-00-1
* - - - -
A8.17.4. Inspect System Components * - - - -
A8.17.5. Remove components
A8.17.5.1. High stage valve inlet pressure sensor
TR: 1C-17A-2-36FI-00-1
- - - -
A8.17.5.2. Precooler inlet temperature sensor
TR: 1C-17A-2-36FI-00-1
- - - -
A8.17.5.3. Mid stage check valve
TR: 1C-17A-2-36FI-00-1
- - - -
A8.17.5.4. High stage regulator pilot valve
TR: 1C-17A-2-36FI-00-1
- - - -
A8.17.5.5. High stage butterfly valve
TR: 1C-17A-2-36FI-00-1
- - - -
A8.17.5.6. Pneumatic high stage manifold
TR: 1C-17A-2-36FI-00-1
- - - -
A8.17.5.7. Pneumatic ducting
TR: 1C-17A-2-36FI-00-1
- - - -
A8.17.5.8. High stage valve exit pressure sensor
TR: 1C-17A-2-36FI-00-1
- - - -
A8.17.5.9. Pylon pressure regulator butterfly valve
TR: 1C-17A-2-36FI-00-1
- - - -
A8.17.5.10. Pylon regulator pilot valve
TR: 1C-17A-2-36FI-00-1
- - - -
A8.17.5.11. Pylon pressure regulator sensor
TR: 1C-17A-2-36FI-00-1
- - - -
A8.17.5.12. Pylon overpressure shutoff valve
TR: 1C-17A-2-36FI-00-1
- - - -
A8.17.5.13. Precooler differential pressure sensor
TR: 1C-17A-2-36FI-00-1
- - - -
A8.17.5.14. Fan air valve
TR: 1C-17A-2-36FI-00-1
- - - -
A8.17.5.15. Precooler
TR: 1C-17A-2-36FI-00-1
- - - -
A8.17.5.16. Precooler exit temperature sensor
TR: 1C-17A-2-36FI-00-1
- - - -
A8.17.5.17. Pneumatic ground service connector
TR: 1C-17A-2-36FI-00-1
- - - -
C-17 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
136Attachment 8
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A8.17.5.18. Engine fan air seal ring
TR: 1C-17A-2-36FI-00-1
- - - -
A8.17.5.19. Center fuselage isolation valve
TR: 1C-17A-2-36FI-00-1
- - - -
A8.17.5.20. APU check valve
TR: 1C-17A-2-36FI-00-1
- - - -
A8.17.5.21. Wing manifold pressure sensor
TR: 1C-C17A-2-36JG-20-1
- - - -
A8.17.5.22. Overheat detector sensing element of MFD system
TR: 1C-C17A-2-36JG-20-1
- - - -
A8.17.5.23. Manifold failure detection controller
TR: 1C-C17A-2-36JG-20-1
* - - - -
A8.17.5.24. Wing differential pressure switch
TR: 1C-C17A-2-36JG-20-1
- - - -
A8.17.5.25. Engine cowl differential pressure switch
TR: 1C-C17A-2-36JG-20-1
- - - -
A8.17.6. Repair components
A8.17.6.1. Pneumatic duct by sealing insulation cover
TR: 1C-17A-2-36FI-00-1
- - - -
A8.17.6.2. Pneumatic duct by patching insulation cover
TR: 1C-17A-2-36FI-00-
- - - -
A8.17.7. Install components
A8.17.7.1. High stage valve inlet pressure sensor
TR: 1C-17A-2-36FI-00-1
- - - -
A8.17.7.2. Precooler inlet temperature sensor
TR: 1C-17A-2-36FI-00-1
- - - -
A8.17.7.3. Mid stage check valve
TR: 1C-17A-2-36FI-00-1
- - - -
A8.17.7.4. High stage regulator pilot valve
TR: 1C-17A-2-36FI-00-1
- - - -
A8.17.7.5. High stage butterfly valve
TR: 1C-17A-2-36FI-00-1
- - - -
A8.17.7.6. Pneumatic high stage manifold
TR: 1C-17A-2-36FI-00-1
- - - -
A8.17.7.7. Pneumatic ducting
TR: 1C-17A-2-36FI-00-1
- - - -
A8.17.7.8. High stage valve exit pressure Sensor
TR: 1C-17A-2-36FI-00-1
- - - -
C-17 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
137Attachment 8
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A8.17.7.9. Pylon pressure regulator butterfly valve
TR: 1C-17A-2-36FI-00-1
- - - -
A8.17.7.10. Pylon regulator pilot valve
TR: 1C-17A-2-36FI-00-1
- - - -
A8.17.7.11. Pylon pressure regulator sensor
TR: 1C-17A-2-36FI-00-1
- - - -
A8.17.7.12. Pylon overpressure shutoff valve
TR: 1C-17A-2-36FI-00-1
- - - -
A8.17.7.13. Precooler differential pressure sensor
TR: 1C-17A-2-36FI-00-1
- - - -
A8.17.7.14. Fan air valve
TR: 1C-17A-2-36FI-00-1
- - - -
A8.17.7.15. Precooler
TR: 1C-17A-2-36FI-00-1
- - - -
A8.17.7.16. Precooler exit temperature sensor
TR: 1C-17A-2-36FI-00-1
- - - -
A8.17.7.17. Pneumatic ground service connector
TR: 1C-17A-2-36FI-00-1
- - - -
A8.17.7.18. Engine fan air seal ring
TR: 1C-17A-2-36FI-00-1
- - - -
A8.17.7.19. Center fuselage isolation valve
TR: 1C-17A-2-36FI-00-1
- - - -
A8.17.7.20. APU check valve
TR: 1C-17A-2-36FI-00-1
- - - -
A8.17.7.21. Wing manifold pressure sensor
TR: 1C-C17A-2-36JG-20-1
- - - -
A8.17.7.22. Overheat detector sensing element of MFD system
TR: 1C-C17A-2-36JG-20-1
- - - -
A8.17.7.23. Manifold failure detection controller
TR: 1C-C17A-2-36JG-20-1
* - - - -
A8.17.7.24. Wing differential pressure switch
TR: 1C-C17A-2-36JG-20-1
- - - -
A8.17.7.25. Engine cowl differential pressure switch
TR: 1C-C17A-2-36JG-20-1
- - - -
A8.17.8. Bench check - - - -
A8.18. AIR CONDITIONING SYSTEM
TR: APPLICABLE AIRCRAFT TO’S
A8.18.1. Operational fundamentals - - - -
C-17 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
138Attachment 8
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A8.18.2. Operational check
A8.18.2.1. Air conditioning system
TR: 1C-17A-2-21JG series
* - - - -
A8.18.2.2. Interrogation of air conditioning system
TR: 1C-17A-2-21JG series
* - - - -
A8.18.2.3. Cargo compt circulation fan
TR: 1C-17A-2-21JG series
- - - -
A8.18.2.4. Avionics equip inlet temperature sensor
TR: 1C-17A-2-21JG series
- - - -
A8.18.2.5. Avionics flow sensors
TR: 1C-17A-2-21JG series
- - - -
A8.18.2.6. Cargo compt ground ventilation fan
TR: 1C-17A-2-21JG series
- - - -
A8.18.2.7. Cargo air shutoff valve
TR: 1C-17A-2-21JG series
- - - -
A8.18.2.8. Temperature control panel
TR: 1C-17A-2-21JG series
- - - -
A8.18.2.9. Ram air ventilation valve
TR: 1C-17A-2-21JG series
- - - -
A8.18.2.10. Cargo floor heater strip
TR: 1C-17A-2-21JG series
- - - -
A8.18.2.11. Ramp floor heating system
TR: 1C-17A-2-21JG series
- - - -
A8.18.2.12. Environmental control system controller
TR: 1C-17A-2-21JG series
* - - - -
A8.18.3. Troubleshoot
A8.18.3.1. Air conditioning sys using FI manual
TR: 1C-17A-2-21FI-00-1
* - - - -
A8.18.4. Inspect System Components * - - - -
A8.18.5. Remove components
A8.18.5.1. Conditioned air check valve
TR: 1C-17A-2-21JG series
- - - -
A8.18.5.2. Conditioned air duct relief valve
TR: 1C-17A-2-21JG series
- - - -
A8.18.5.3. Flow distribution mix chamber
TR: 1C-17A-2-21JG series
- - - -
A8.18.5.4. Environmental control panel assembly
TR: 1C-17A-2-21JG series
*R - - - -
C-17 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
139Attachment 8
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A8.18.5.5. Flow distribution mix chamber
TR: 1C-17A-2-21JG series
- - - -
A8.18.5.6. Cargo compartment recirculation check Valve
TR: 1C-17A-2-21JG series
- - - -
A8.18.5.7. Cargo compartment circulation fan
TR: 1C-17A-2-21JG series
- - - -
A8.18.5.8. Filter element for cargo compt circulation fan
TR: 1C-17A-2-21JG series
- - - -
A8.18.5.9. Ground conditioned air check valve
TR: 1C-17A-2-21JG series
- - - -
A8.18.5.10. Crew air shutoff valve
TR: 1C-17A-2-21JG series
- - - -
A8.18.5.11. Manual globe air valve
TR: 1C-17A-2-21JG series
- - - -
A8.18.5.12. Avionics cooling fan
TR: 1C-17A-2-21JG series
- - - -
A8.18.5.13. Avionics cooling fan check valve
TR: 1C-17A-2-21JG series
- - - -
A8.18.5.14. Avionics cooling outflow valve
TR: 1C-17A-2-21JG series
- - - -
A8.18.5.15. Augmentation Valve
TR: 1C-17A-2-21JG series
- - - -
A8.18.5.16. Cooling avionics heat exchanger bypass valve
TR: 1C-17A-2-21JG series
- - - -
A8.18.5.17. Backup avionics outflow valve
TR: 1C-17A-2-21JG series
- - - -
A8.18.5.18. Ground inlet shutoff valve
TR: 1C-17A-2-21JG series
- - - -
A8.18.5.19. Avionics equipment inlet temperature sensors
TR: 1C-17A-2-21JG series
- - - -
A8.18.5.20. Avionics cooling shutoff valve
TR: 1C-17A-2-21JG series
- - - -
A8.18.5.21. Avionics flow sensor
TR: 1C-17A-2-21JG series
- - - -
A8.18.5.22. Cargo compt ground ventilation fan
TR: 1C-17A-2-21JG series
- - - -
A8.18.5.23. Cargo air shutoff valve
TR: 1C-17A-2-21JG series
- - - -
C-17 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
140Attachment 8
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A8.18.5.24. Temperature control panel
TR: 1C-17A-2-21JG series
- - - -
A8.18.5.25. Loadmaster station manual globe air valve
TR: 1C-17A-2-21JG series
- - - -
A8.18.5.26. Ram air ventilation valve
TR: 1C-17A-2-21JG series
- - - -
A8.18.5.27. Ram air vent valve actuator
TR: 1C-17A-2-21JG series
- - - -
A8.18.5.28. Cargo floor heater strip
TR: 1C-17A-2-21JG series
- - - -
A8.18.5.29. Ramp heater/blower
TR: 1C-17A-2-21JG series
- - - -
A8.18.5.30. Ramp floor thermostat
TR: 1C-17A-2-21JG series
- - - -
A8.18.5.31 .Flow control valve
TR: 1C-17A-2-21JG series
- - - -
A8.18.5.32. Pack discharge thermostat
TR: 1C-17A-2-21JG series
- - - -
A8.18.5.33. Water separator pack discharge temp sensor
TR: 1C-17A-2-21JG series
- - - -
A8.18.5.34. Refrigeration Unit
TR: 1C-17A-2-21JG series
- - - -
A8.18.5.35. Ram air plenum
TR: 1C-17A-2-21JG series
- - - -
A8.18.5.36. Pack anti-ice valve
TR: 1C-17A-2-21JG series
- - - -
A8.18.5.37. Turbine bypass valve
TR: 1C-17A-2-21JG series
- - - -
A8.18.5.38. Air conditioning heat exchanger
TR: 1C-17A-2-21JG series
- - - -
A8.18.5.39. Air cycle machine
TR: 1C-17A-2-21JG series
- - - -
A8.18.5.40. Compressor discharge overtemp fusible plug on ACM
TR: 1C-17A-2-21JG series
- - - -
A8.18.5.41. Turbine inlet overtemp fusible plug on ACM
TR: 1C-17A-2-21JG series
- - - -
A8.18.5.42. Water injector nozzle
TR: 1C-17A-2-21JG series
- - - -
C-17 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
141Attachment 8
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A8.18.5.43. Water separator assembly
TR: 1C-17A-2-21JG series
- - - -
A8.18.5.44. Coalescer bag on water separator
TR: 1C-17A-2-21JG series
* - - - -
A8.18.5.45. Bypass valve on water separator
TR: 1C-17A-2-21JG series
- - - -
A8.18.5.46. Pressure sensor on water separator
TR: 1C-17A-2-21JG series
- - - -
A8.18.5.47. Ram air inlet scoop assembly
TR: 1C-17A-2-21JG series
- - - -
A8.18.5.48. Linear ram air electro-mechanical actuator
TR: 1C-17A-2-21JG series
- - - -
A8.18.5.49. Ram air exhaust valve assembly
TR: 1C-17A-2-21JG series
- - - -
A8.18.5.50. Ram air inlet duct assembly
TR: 1C-17A-2-21JG series
- - - -
A8.18.5.51. Trim air regulator valve
TR: 1C-17A-2-21JG series
- - - -
A8.18.5.52. Trim air check valve
TR: 1C-17A-2-21JG series
- - - -
A8.18.5.53. Trim air delta pressure sensor
TR: 1C-17A-2-21JG series
- - - -
A8.18.5.54. Cockpit air temperature sensing ejector assembly
TR: 1C-17A-2-21JG series
- - - -
A8.18.5.55. Temp sensor on cockpit air temp ejector assembly
TR: 1C-17A-2-21JG series
- - - -
A8.18.5.56. Cockpit trim air valve
TR: 1C-17A-2-21JG series
- - - -
A8.18.5.57. Cockpit zone inlet air temperature sensor
TR: 1C-17A-2-21JG series
- - - -
A8.18.5.58. Cargo compt trim air valve
TR: 1C-17A-2-21JG series
- - - -
A8.18.5.59. Cargo compt air temp sensing ejector assembly
TR: 1C-17A-2-21JG series
- - - -
A8.18.5.60. Temp sensor on cargo compt air temp sensing ejector assembly
TR: 1C-17A-2-21JG series
- - - -
A8.18.5.61. Cargo compt zone inlet air temp sensor
TR: 1C-17A-2-21JG series
- - - -
C-17 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
142Attachment 8
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A8.18.5.62. Crew rest trim valve
TR: 1C-17A-2-21JG series
- - - -
A8.18.5.63. Crew rest air temp sensing ejector assembly
TR: 1C-17A-2-21JG series
- - - -
A8.18.5.64. Temp sensor on crew rest air temp ejector assembly
TR: 1C-17A-2-21JG series
- - - -
A8.18.5.65. Crew rest zone inlet air temp sensor
TR: 1C-17A-2-21JG series
- - - -
A8.18.5.66. Environmental control system controller
TR: 1C-17A-2-21JG series
* - - - -
A8.18.6. Repair components
A8.18.6.1. Adjust ram air inlet scoop assembly
TR: 1C-17A-2-21JG series
- - - -
A8.18.7. Install components
A8.18.7.1. Conditioned air check valve
TR: 1C-17A-2-21JG series
- - - -
A8.18.7.2. Conditioned air duct relief valve
TR: 1C-17A-2-21JG series
- - - -
A8.18.7.3. Flow distribution mix chamber
TR: 1C-17A-2-21JG series
- - - -
A8.18.7.4. Environmental control panel assembly
TR: 1C-17A-2-21JG series
* - - - -
A8.18.7.5. Flow distribution mix chamber
TR: 1C-17A-2-21JG series
- - - -
A8.18.7.6. Cargo compartment recirculation check valve
TR: 1C-17A-2-21JG series
- - - -
A8.18.7.7. Cargo compartment circulation fan
TR: 1C-17A-2-21JG series
- - - -
A8.18.7.8. Filter element for cargo compt circulation fan
TR: 1C-17A-2-21JG series
- - - -
A8.18.7.9. Ground conditioned air check valve
TR: 1C-17A-2-21JG series
- - - -
A8.18.7.10. Crew air shutoff valve
TR: 1C-17A-2-21JG series
- - - -
A8.18.7.11. Manual globe air valve
TR: 1C-17A-2-21JG series
- - - -
A8.18.7.12. Avionics cooling fan
TR: 1C-17A-2-21JG series
- - - -
C-17 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
143Attachment 8
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A8.18.7.13. Avionics cooling fan check valve
TR: 1C-17A-2-21JG series
- - - -
A8.18.7.14. Avionics cooling outflow valve
TR: 1C-17A-2-21JG series
- - - -
A8.18.7.15. Augmentation valve
TR: 1C-17A-2-21JG series
- - - -
A8.18.7.16. Cooling avionics heat exchanger bypass valve
TR: 1C-17A-2-21JG series
- - - -
A8.18.7.17. Backup avionics outflow valve
TR: 1C-17A-2-21JG series
- - - -
A8.18.7.18. Ground inlet shutoff valve
TR: 1C-17A-2-21JG series
- - - -
A8.18.7.19. Avionics equipment inlet temperature sensors
TR: 1C-17A-2-21JG series
- - - -
A8.18.7.20. Avionics cooling shutoff valve
TR: 1C-17A-2-21JG series
- - - -
A8.18.7.21. Avionics flow sensor
TR: 1C-17A-2-21JG series
- - - -
A8.18.7.22. Cargo compt ground ventilation Fan
TR: 1C-17A-2-21JG series
- - - -
A8.18.7.23. Cargo air shutoff valve
TR: 1C-17A-2-21JG series
- - - -
A8.18.7.24. Temperature control panel
TR: 1C-17A-2-21JG series
- - - -
A8.18.7.25. Loadmaster station manual globe air valve
TR: 1C-17A-2-21JG series
- - - -
A8.18.7.26. Ram air ventilation valve
TR: 1C-17A-2-21JG series
- - - -
A8.18.7.27. Ram air vent valve actuator
TR: 1C-17A-2-21JG series
- - - -
A8.18.7.28. Cargo floor heater strip
TR: 1C-17A-2-21JG series
- - - -
A8.18.7.29. Ramp heater/blower
TR: 1C-17A-2-21JG series
- - - -
A8.18.7.30. Ramp floor thermostat
TR: 1C-17A-2-21JG series
- - - -
A8.18.7.31. Flow control valve
TR: 1C-17A-2-21JG series
- - - -
C-17 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
144Attachment 8
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A8.18.7.32. Pack discharge thermostat
TR: 1C-17A-2-21JG series
- - - -
A8.18.7.33. Water separator pack discharge temp sensor
TR: 1C-17A-2-21JG series
- - - -
A8.18.7.34. Refrigeration unit
TR: 1C-17A-2-21JG series
- - - -
A8.18.7.35. Ram air plenum
TR: 1C-17A-2-21JG series
- - - -
A8.18.7.36. Pack anti-ice valve
TR: 1C-17A-2-21JG series
- - - -
A8.18.7.37. Turbine bypass valve
TR: 1C-17A-2-21JG series
- - - -
A8.18.7.38. Air conditioning heat exchanger
TR: 1C-17A-2-21JG series
- - - -
A8.18.7.39. Air cycle machine
TR: 1C-17A-2-21JG series
- - - -
A8.18.7.40. Compressor discharge overtemp fusible plug on AMC
TR: 1C-17A-2-21JG series
- - - -
A8.18.7.41. Turbine inlet overtemp fusible plug on ACM
TR: 1C-17A-2-21JG series
- - - -
A8.18.7.42. Water injector nozzle
TR: 1C-17A-2-21JG series
- - - -
A8.18.7.43. Water separator assembly
TR: 1C-17A-2-21JG series
- - - -
A8.18.7.44. Coalescer bag on water separator
TR: 1C-17A-2-21JG series
* - - - -
A8.18.7.45. Bypass valve on water separator
TR: 1C-17A-2-21JG series
- - - -
A8.18.7.46. Pressure sensor on water separator
TR: 1C-17A-2-21JG series
- - - -
A8.18.7.47. Ram air inlet scoop assembly
TR: 1C-17A-2-21JG series
- - - -
A8.18.7.48. Linear ram air electro-mechanical actuator
TR: 1C-17A-2-21JG series
- - - -
A8.18.7.49. Ram air exhaust valve assembly
TR: 1C-17A-2-21JG series
- - - -
A8.18.7.50. Ram air inlet duct assembly
TR: 1C-17A-2-21JG series
- - - -
C-17 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
145Attachment 8
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A8.18.7.51. Trim air regulator valve
TR: 1C-17A-2-21JG series
- - - -
A8.18.7.52. Trim air check valve
TR: 1C-17A-2-21JG series
- - - -
A8.18.7.53. Trim air delta pressure sensor
TR: 1C-17A-2-21JG series
- - - -
A8.18.7.54. Cockpit air temperature sensing ejector assembly
TR: 1C-17A-2-21JG series
- - - -
A8.18.7.55. Temp sensor on cockpit air temp ejector assembly
TR: 1C-17A-2-21JG series
- - - -
A8.18.7.56. Cockpit trim air valve
TR: 1C-17A-2-21JG series
- - - -
A8.18.7.57. Cockpit zone inlet air temperature sensor
TR: 1C-17A-2-21JG series
- - - -
A8.18.7.58. Cargo compt trim air valve
TR: 1C-17A-2-21JG series
- - - -
A8.18.7.59. Cargo compt air temp sensing ejector assembly
TR: 1C-17A-2-21JG series
- - - -
A8.18.7.60. Temp sensor on cargo compt air temp sensing ejectorassembly
TR: 1C-17A-2-21JG series
- - - -
A8.18.7.61. Cargo compt zone inlet air temp sensor
TR: 1C-17A-2-21JG series
- - - -
A8.18.7.62. Crew rest trim valve
TR: 1C-17A-2-21JG series
- - - -
A8.18.7.63. Crew rest air temp sensing ejector assembly
TR: 1C-17A-2-21JG series
- - - -
A8.18.7.64. Temp sensor on crew rest air temp ejector assembly
TR: 1C-17A-2-21JG series
- - - -
A8.18.7.65. Crew rest zone inlet air temp sensor
TR: 1C-17A-2-21JG series
- - - -
A8.18.7.66. Environmental control system controller
TR: 1C-17A-2-21JG series
* - - - -
A8.19. PRESSURIZATION SYSTEM
TR: APPLICABLE AIRCRAFT TO’S
A8.19.1. Operational fundamentals - - - -
A8.19.2 Operational check
A8.19.2.1. Pressurization system
TR: 1C-17A-2-21JG series
*R - - - -
C-17 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
146Attachment 8
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A8.19.3. Troubleshoot System *R - - - -
A8.19.4. Inspect System Components *R - - - -
A8.19.5. Remove components
A8.19.5.1. Automatic cabin pressure controller
TR: 1C-17A-2-21JG series
* - - - -
A8.19.5.2. Cabin pressure outflow valve body
TR: 1C-17A-2-21JG series
- - - -
A8.19.5.3. Cabin pressure selector panel
TR: 1C-17A-2-21JG series
- - - -
A8.19.5.4. Cabin pressure transducer
TR: 1C-17A-2-21JG series
- - - -
A8.19.5.5. Alternating current motor
TR: 1C-17A-2-21JG series
- - - -
A8.19.5.6. Direct current motor
TR: 1C-17A-2-21JG series
- - - -
A8.19.5.7. Cabin pressure indication panel assembly
TR: 1C-17A-2-21JG series
- - - -
A8.19.5.8. Cabin pressure indicator
TR: 1C-17A-2-21JG series
- - - -
A8.19.5.9. Cabin 10,000 foot pressure aneroid switch
TR: 1C-17A-2-21JG series
- - - -
A8.19.5.10. Cabin positive press and temperature relief valve
TR: 1C-17A-2-21JG series
- - - -
A8.19.6. Repair components - - - -
A8.19.7. Install components
A8.19.7.1. Automatic cabin pressure controller
TR: 1C-17A-2-21JG series
* - - - -
A8.19.7.2. Cabin pressure outflow valve body
TR: 1C-17A-2-21JG series
- - - -
A8.19.7.3. Cabin pressure selector panel
TR: 1C-17A-2-21JG series
- - - -
A8.19.7.4. Cabin pressure transducer
TR: 1C-17A-2-21JG series
- - - -
A8.19.7.5. Alternating current motor
TR: 1C-17A-2-21JG series
- - - -
A8.19.7.6. Direct current motor
TR: 1C-17A-2-21JG series
- - - -
A8.19.7.7. Cabin pressure indication panel assembly - - - -
C-17 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
147Attachment 8
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
TR: 1C-17A-2-21JG series
A8.19.7.8. Cabin pressure indicator
TR: 1C-17A-2-21JG series
- - - -
A8.19.7.9. Cabin 10,000 foot pressure aneroid switch
TR: 1C-17A-2-21JG series
- - - -
A8.19.7.10. Cabin positive press and temperature relief Valve
TR: 1C-17A-2-21JG series
- - - -
A8.19.8. Bench check - - - -
A8.20. OXYGEN SYSTEM
TR: APPLICABLE AIRCRAFT TO’S
A8.20.1. Operational fundamentals - - - -
A8.20.2. Operational check
A8.20.2.1. Panel-mounted diluter demand o2 regulator
TR: 1C-17A-2-35JG series
* - - - -
A8.20.2.2. O2 quick don mask
TR: 1C-17A-2-35JG series
- - - -
A8.20.2.3. Crew portable oxy cylinder recharger assembly
TR: 1C-17A-2-35JG series
- - - -
A8.20.2.4. LOX converter
TR: 1C-17A-2-35JG series
- - - -
A8.20.2.5. Emer sys pass sidewall seat and aeromed sw
TR: 1C-17A-2-35JG series
- - - -
A8.20.2.6. Emer sys pass sidewall seat and manual mode
TR: 1C-17A-2-35JG series
- - - -
A8.20.2.7. Halo therapeutic dial ind pressure gauge
TR: 1C-17A-2-35JG series
- - - -
A8.20.2.8. LOX quantity indicator
TR: 1C-17A-2-35JG series
- - - -
A8.20.2.9. Port O2 cylinder and regulator
TR: 1C-17A-2-35JG series
- - - -
A8.20.2.10. Port O2 cylinder and regulator
TR: 1C-17A-2-35JG series
- - - -
A8.20.2.11. Portable oxygen mask
TR: 1C-17A-2-35JG series
- - - -
A8.20.3. Troubleshoot
A8.20.3.1. Oxygen sys. using FI Manual
TR: 1C-17A-2-35FI-00-1
* - - - -
A8.20.4. Inspect System Components * - - - -
C-17 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
148Attachment 8
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A8.20.5. Remove components
A8.20.5.1. Liquid quantity indicator (totalizer)
TR: 1C-17A-2-28JG series
- - - -
A8.20.5.2. Crew liquid oxygen converter
TR: 1C-17A-2-35JG series
- - - -
A8.20.5.3. Crew relief valve
TR: 1C-17A-2-35JG series
- - - -
A8.20.5.4. Crew liquid oxygen drain valve
TR: 1C-17A-2-35JG series
- - - -
A8.20.5.5. Crew liquid oxygen fill valve
TR: 1C-17A-2-35JG series
- - - -
A8.20.5.6. Crew oxygen heat exchanger
TR: 1C-17A-2-35JG series
- - - -
A8.20.5.7. Crew oxygen check valve
TR: 1C-17A-2-35JG series
- - - -
A8.20.5.8. Oxygen shutoff crossfeed valve
TR: 1C-17A-2-35JG series
- - - -
A8.20.5.9. Panel mounted diluter demand oxygen regulator
TR: 1C-17A-2-35JG series
* - - - -
A8.20.5.10. Lavatory demand barometric oxygen regulator valve
TR: 1C-17A-2-35JG series
- - - -
A8.20.5.11. Crew liquid oxygen manual shutoff valve
TR: 1C-17A-2-35JG series
- - - -
A8.20.5.12. Oxygen quick don mask
TR: 1C-17A-2-35JG series
- - - -
A8.20.5.13. Lavatory emergency oxygen mask container assembly
TR: 1C-17A-2-35JG series
- - - -
A8.20.5.14. Door hinge on lav emer o2 mask container assembly
TR: 1C-17A-2-35JG series
- - - -
A8.20.5.15. Lav emer oxygen drop mask
TR: 1C-17A-2-35JG series
- - - -
A8.20.5.16. Lav emergency oxygen mask manifold
TR: 1C-17A-2-35JG series
- - - -
A8.20.5.17. Crew oxygen low pressure switch
TR: 1C-17A-2-35JG series
- - - -
A8.20.5.18. Crew liquid oxygen quantity indicator
TR: 1C-17A-2-35JG series
- - - -
A8.20.5.19. Crew portable oxy cylinder recharger assembly - - - -
C-17 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
149Attachment 8
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
TR: 1C-17A-2-35JG series
A8.20.5.20. Liquid oxygen converter
TR: 1C-17A-2-35JG series
- - - -
A8.20.5.21. Liquid oxygen drain valve
TR: 1C-17A-2-35JG series
- - - -
A8.20.5.22. Liquid oxygen fill valve
TR: 1C-17A-2-35JG series
- - - -
A8.20.5.23. Liquid oxygen manual shutoff valve
TR: 1C-17A-2-35JG series
- - - -
A8.20.5.24. Passenger oxygen heat exchanger
TR: 1C-17A-2-35JG series
- - - -
A8.20.5.25. Oxygen check valve
TR: 1C-17A-2-35JG series
- - - -
A8.20.5.26. 430 psi passenger oxygen relief valve
TR: 1C-17A-2-35JG series
- - - -
A8.20.5.27. Passenger dial indicating-oxygen pressure gauge
TR: 1C-17A-2-35JG series
- - - -
A8.20.5.28. Auxiliary oxygen heat exchanger
TR: 1C-17A-2-35JG series
- - - -
A8.20.5.29. Aft loadmaster panel mounted diluter demand O2 reg
TR: 1C-17A-2-35JG series
- - - -
A8.20.5.30. Centerline seat O2 supply hose on emer sys
TR: 1C-17A-2-35JG series
- - - -
A8.20.5.31. Pass barometric demand regulator
TR: 1C-17A-2-35JG series
- - - -
A8.20.5.32. Emergency oxygen mask container
TR: 1C-17A-2-35JG series
- - - -
A8.20.5.33. Emer O2 mask container with switch
TR: 1C-17A-2-35JG series
- - - -
A8.20.5.34. Litter emergency O2 mask container
TR: 1C-17A-2-35JG series
- - - -
A8.20.5.35. Emergency oxygen manifold
TR: 1C-17A-2-35JG series
- - - -
A8.20.5.36. 50 psi halo therapeutic regulator
TR: 1C-17A-2-35JG series
- - - -
A8.20.5.37. Dial indicating-halo therapeutic pressure gauge
TR: 1C-17A-2-35JG series
- - - -
A8.20.5.38. Emergency oxygen mask - - - -
C-17 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
150Attachment 8
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
TR: 1C-17A-2-35JG series
A8.20.5.39. Oxygen low pressure switch
TR: 1C-17A-2-35JG series
- - - -
A8.20.5.40. Liquid oxygen quantity indicator
TR: 1C-17A-2-35JG series
- - - -
A8.20.5.41. Pass O2 cyl port quick-disc recharger assembly
TR: 1C-17A-2-35JG series
- - - -
A8.20.5.42. Portable O2 cylinder and regulator
TR: 1C-17A-2-35JG series
- - - -
A8.20.5.43. Portable O2 mask
TR: 1C-17A-2-35JG series
- - - -
A8.20.6. Repair components - - - -
A8.20.7. Install components
A8.20.7.1. Liquid quantity indicator (totalizer)
TR: 1C-17A-2-28JG series
- - - -
A8.20.7.2. Crew liquid oxygen converter
TR: 1C-17A-2-35JG series
- - - -
A8.20.7.3. Crew relief valve
TR: 1C-17A-2-35JG series
- - - -
A8.20.7.4. Crew liquid oxygen drain valve
TR: 1C-17A-2-35JG series
- - - -
A8.20.7.5. Crew liquid oxygen fill valve
TR: 1C-17A-2-35JG series
- - - -
A8.20.7.6. Crew oxygen heat exchanger
TR: 1C-17A-2-35JG series
- - - -
A8.20.7.7. Crew oxygen check valve
TR: 1C-17A-2-35JG series
- - - -
A8.20.7.8. Oxygen shutoff crossfeed valve
TR: 1C-17A-2-35JG series
- - - -
A8.20.7.9. Panel mounted diluter demand oxygen regulator
TR: 1C-17A-2-35JG series
* - - - -
A8.20.7.10. Lavatory demand barometric oxygen regulator valve
TR: 1C-17A-2-35JG series
- - - -
A8.20.7.11. Crew liquid oxygen manual shutoff valve
TR: 1C-17A-2-35JG series
- - - -
A8.20.7.12. Oxygen quick don mask
TR: 1C-17A-2-35JG series
- - - -
A8.20.7.13. Lavatory emergency oxygen mask container assembly - - - -
C-17 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
151Attachment 8
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
TR: 1C-17A-2-35JG series
A8.20.7.14. Door hinge on lav emer o2 mask container assembly
TR: 1C-17A-2-35JG series
- - - -
A8.20.7.15. Lav emer oxygen drop mask
TR: 1C-17A-2-35JG series
- - - -
A8.20.7.16. Lav emergency oxygen mask manifold
TR: 1C-17A-2-35JG series
- - - -
A8.20.7.17. Crew oxygen low pressure switch
TR: 1C-17A-2-35JG series
- - - -
A8.20.7.18. Crew liquid oxygen quantity indicator
TR: 1C-17A-2-35JG series
- - - -
A8.20.7.19. Crew portable oxy cylinder recharger assembly
TR: 1C-17A-2-35JG series
- - - -
A8.20.7.20. Liquid oxygen converter
TR: 1C-17A-2-35JG series
- - - -
A8.20.7.21. Liquid oxygen drain valve
TR: 1C-17A-2-35JG series
- - - -
A8.20.7.22. Liquid oxygen fill valve
TR: 1C-17A-2-35JG series
- - - -
A8.20.7.23. Liquid oxygen manual shutoff valve
TR: 1C-17A-2-35JG series
- - - -
A8.20.7.24. Passenger oxygen heat exchanger
TR: 1C-17A-2-35JG series
- - - -
A8.20.7.25. Oxygen check valve
TR: 1C-17A-2-35JG series
- - - -
A8.20.7.26. 430 psi passenger oxygen relief valve
TR: 1C-17A-2-35JG series
- - - -
A8.20.7.27. Passenger dial indicating-oxygen pressure gauge
TR: 1C-17A-2-35JG series
- - - -
A8.20.7.28. Auxiliary oxygen heat exchanger
TR: 1C-17A-2-35JG series
- - - -
A8.20.7.29. Aft loadmaster panel mounted diluter demand O2 reg
TR: 1C-17A-2-35JG series
- - - -
A8.20.7.30. Centerline seat O2 supply hose on emer sys
TR: 1C-17A-2-35JG series
- - - -
A8.20.7.31. Pass barometric demand regulator
TR: 1C-17A-2-35JG series
- - - -
A8.20.7.32. Emergency oxygen mask container - - - -
C-17 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
152Attachment 8
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
TR: 1C-17A-2-35JG series
A8.20.7.33. Emer O2 mask container with switch
TR: 1C-17A-2-35JG series
- - - -
A8.20.7.34. Litter emergency O2 mask container
TR: 1C-17A-2-35JG series
- - - -
A8.20.7.35. Emergency oxygen manifold
TR: 1C-17A-2-35JG series
- - - -
A8.20.7.36. 50 psi halo therapeutic regulator
TR: 1C-17A-2-35JG series
- - - -
A8.20.7.37. Dial indicating-halo therapeutic pressure gauge
TR: 1C-17A-2-35JG series
- - - -
A8.20.7.38. Emergency oxygen mask
TR: 1C-17A-2-35JG series
- - - -
A8.20.7.39. Oxygen low pressure switch
TR: 1C-17A-2-35JG series
- - - -
A8.20.7.40. Liquid oxygen quantity indicator
TR: 1C-17A-2-35JG series
- - - -
A8.20.7.41. Pass O2 cyl port quick-disc recharger assembly
TR: 1C-17A-2-35JG series
- - - -
A8.20.7.42. Portable O2 cylinder and regulator
TR: 1C-17A-2-35JG series
- - - -
A8.20.7.43. Portable O2 mask
TR: 1C-17A-2-35JG series
- - - -
A8.20.8. Bench check - - - -
A8.20.9. Drain LOX converter
TR: 1C-17A-2-12JG series
- - - -
A8.20.10. Purge LOX converter
TR: 1C-17A-2-12JG series
- - - -
A8.20.11. Repack Crew oxygen mask
TR: 1C-17A-2-35JG series
- - - -
A8.20.12. Repack sidewall pass emergency O2 mask
TR: 1C-17A-2-35JG series
* - - - -
A8.20.13. Service LOX
TR: 1C-17A-2-12JG series
- - - -
A8.21. LIFE RAFT INFLATION EQUIPMENT
TR: Ref 14S series TO’s
A8.21.1. Operational fundamentals - - - -
A8.21.2. Operational check
C-17 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
153Attachment 8
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A8.21.2.1. Flotation equipment deployment system
TR: 1C-C17A-2-95JG-20-1
- - - -
A8.21.2.2. Ramp escape blowdown
TR: 1C-C17A-2-95JG-30-1
- - - -
A8.21.3. Troubleshoot
A8.21.3.1. Crew escape & safety sys using FI manual
TR: 1C-C17A-2-95FI-00-1
*R - - - -
A8.21.4. Inspect *R - - - -
A8.21.5. Remove components
A8.21.5.1. Fed arm control panel
TR: 1C-C17A-2-95JG-20-1
- - - -
A8.21.5.2. Arm fire initiator
TR: 1C-C17A-2-95JG-20-1
- - - -
A8.21.5.3. Retractor assembly
TR: 1C-C17A-2-95JG-20-1
- - - -
A8.21.5.4. Shaped charge assembly
TR: 1C-C17A-2-95JG-20-1
- - - -
A8.21.5.5. Shielded mild detonating cord
TR: 1C-C17A-2-95JG-20-1
- - - -
A8.21.5.6. Shielded mild detonating cord union
TR: 1C-C17A-2-95JG-20-1
- - - -
A8.21.5.7. 4 port manifold
TR: 1C-C17A-2-95JG-20-1
- - - -
A8.21.5.8. Port manifold
TR: 1C-C17A-2-95JG-20-1
- - - -
A8.21.5.9. Aft loadmaster ramp blowdown panel
TR: 1C-C17A-2-95JG-30-1
- - - -
A8.21.5.10. Forward loadmaster ramp blowdown panel
TR: 1C-C17A-2-95JG-30-1
- - - -
A8.21.5.11. Ramp emergency egress battery
TR: 1C-C17A-2-95JG-30-1
* - - - -
A8.21.5.12. Ramp door emergency exit sign
TR: 1C-C17A-2-95JG-30-1
- - - -
A8.21.6. Repair components - - - -
A8.21.7. Install components
A8.21.7.1. Fed arm control panel
TR: 1C-C17A-2-95JG-20-1
- - - -
A8.21.7.2. Arm fire initiator - - - -
C-17 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
154Attachment 8
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
TR: 1C-C17A-2-95JG-20-1
A8.21.7.3. Retractor assembly
TR: 1C-C17A-2-95JG-20-1
- - - -
A8.21.7.4. Shaped charge assembly
TR: 1C-C17A-2-95JG-20-1
- - - -
A8.21.7.5. Shielded mild detonating cord
TR: 1C-C17A-2-95JG-20-1
- - - -
A8.21.7.6. Shielded mild detonating cord union
TR: 1C-C17A-2-95JG-20-1
- - - -
A8.21.7.7. 4 port manifold
TR: 1C-C17A-2-95JG-20-1
- - - -
A8.21.7.8. Port manifold
TR: 1C-C17A-2-95JG-20-1
- - - -
A8.21.7.9. Aft loadmaster ramp blowdown panel
TR: 1C-C17A-2-95JG-30-1
- - - -
A8.21.7.10. Forward loadmaster ramp blowdown panel
TR: 1C-C17A-2-95JG-30-1
- - - -
A8.21.7.11. Ramp emergency egress battery
TR: 1C-C17A-2-95JG-30-1
* - - - -
A8.21.7.12. Ramp door emergency exit sign
TR: 1C-C17A-2-95JG-30-1
- - - -
A8.21.8. Bench check - - - -
A8.22. MISCELLANEOUS SYSTEMS
TR: APPLICABLE AIRCRAFT TO’S
A8.22.1. Operational fundamentals - - - -
A8.22.2. Operational check
A8.22.2.1. Hyd Pwr Sys
TR: 1C-17A-2-29JG series
- - - -
A8.22.2.2. Hyd Pwr Main Sys
TR: 1C-17A-2-29JG series
- - - -
A8.22.2.3. RAT System
TR: 1C-17A-2-29JG series
- - - -
A8.22.2.4. Potable water sys
TR: 1C-C17A-2-38JG-10-1
- - - -
A8.22.2.5. Electric water heater
TR: 1C-C17A-2-38JG-10-1
- - - -
A8.22.2.6. Waste disposal sys
TR: 1C-C17A-2-38JG-30-1
- - - -
C-17 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
155Attachment 8
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A8.22.2.7. Potable water remote fault display sys
TR: 1C-C17A-2-40JG-20-1
- - - -
A8.22.2.8. Lighted nav chart holder
TR: 1C-17A-2-25JG series
- - - -
A8.22.2.9. Galley module system
TR: 1C-17A-2-25JG series
- - - -
A8.22.3. Troubleshoot
A8.22.3.1. Hyd. sys using FI manual
TR: 1C-17A-2-29FI-00-1
*R - - - -
A8.22.3.2. Water/waste sys using FI manual
TR: 1C-C17A-2-38FI-00-1
* - - - -
A8.22.3.3. Potable water sys integration using FI manual
TR: 1C-C17A-2-40FI-00-1
* - - - -
A8.22.3.4. Equipment & furnishings using FI manual
TR: 1C-17A-2-25FI-00-1
*R - - - -
A8.22.4. Inspect System Components *R - - - -
A8.22.5. Remove components
A8.22.5.1. Hyd sys pnl assembly
TR: 1C-17A-2-29JG series
- - - -
A8.22.5.2. RAT uplock electro mech linear
TR: 1C-17A-2-29JG series
- - - -
A8.22.5.3. Maintenance monitor panel
TR: 1C-C17A-2-40JG-20-1
- - - -
A8.22.5.4. Potable water service panel assembly
TR: 1C-C17A-2-38JG-10-1
- - - -
A8.22.5.5. Electric water heater
TR: 1C-C17A-2-38JG-10-1
- - - -
A8.22.5.6. Crew toilet pump & motor assembly
TR: 1C-C17A-2-38JG-30-1
- - - -
A8.22.5.7. Fan thrust reverser actuator proximity sensor
TR: 1C-C17A-2-78JG-30-1
- - - -
A8.22.5.11. Lighted nav chart holder
TR: 1C-17A-2-25JG series
- - - -
A8.22.5.12. Lighted nav chart holder lens
TR: 1C-17A-2-25JG series
- - - -
A8.22.5.13. Flt. checklist holder
TR: 1C-17A-2-25JG series
- - - -
A8.22.5.14. Galley module hot cup timer - - - -
C-17 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
156Attachment 8
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
TR: 1C-17A-2-25JG series
A8.22.5.15. Lav shaver power supply
TR: 1C-17A-2-25JG series
- - - -
A8.22.6. Repair components
A8.22.6.1. Pressure sys by replacing potable water press switch
TR: 1C-C17A-2-38JG-40-1
- - - -
A8.22.7 .Install components
A8.22.7.1. Hyd sys pnl assembly
TR: 1C-17A-2-29JG series
- - - -
A8.22.7.2. RAT uplock electro mech linear
TR: 1C-17A-2-29JG series
- - - -
A8.22.7.3. Maintenance monitor panel
TR: 1C-C17A-2-40JG-20-1
- - - -
A8.22.7.4. Potable water service panel assembly
TR: 1C-C17A-2-38JG-10-1
- - - -
A8.22.7.5. Electric water heater
TR: 1C-C17A-2-38JG-10-1
- - - -
A8.22.7.6. Crew toilet pump & motor assembly
TR: 1C-C17A-2-38JG-30-1
- - - -
A8.22.7.7. Fan thrust reverser actuator proximity sensor
TR: 1C-C17A-2-78JG-30-1
- - - -
A8.22.7.11. Lighted nav chart holder
TR: 1C-17A-2-25JG series
- - - -
A8.22.7.12. Lighted nav chart holder lens
TR: 1C-17A-2-25JG series
- - - -
A8.22.7.13. Flt. checklist holder
TR: 1C-17A-2-25JG series
- - - -
A8.22.7.14. Galley module hot cup timer
TR: 1C-17A-2-25JG series
- - - -
A8.22.7.15. Lav shaver power supply
TR: 1C-17A-2-25JG series
- - - -
A8.22.8. Operate
A8.22.8.1. VHF system
TR: 1C-17A-2-23JG series
- - - -
A8.22.8.2. UHF system
TR: 1C-17A-2-23JG series
- - - -
A8.22.8.3. Cargo interphone system
TR: 1C-17A-2-23JG series
- - - -
C-17 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
157Attachment 8
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A8.22.8.4. Maintenance interphone system
TR: 1C-17A-2-23JG series
* - - - -
A8.22.8.5. Flight station interphone system
TR: 1C-17A-2-23JG series
- - - -
A8.22.8.6. IRMS
TR: 1C-17A-2-23JG series
- - - -
A8.22.8.7. Hyd sys controller
TR: 1C-17A-2-29JG series
- - - -
A8.22.8.8. Aux hyd sys
TR: 1C-17A-2-29JG series
- - - -
A8.22.8.9. Stow/deploy RAT assembly
TR: 1C-17A-2-29JG series
- - - -
A8.22.8.10. MMP using maintenance monitor mode to view faults
TR: 1C-C17A-2-40JG-20-1
* - - - -
A8.22.8.11. MMP using maintenance monitor mode to view & erase faults
TR: 1C-C17A-2-40JG-20-1
* - - - -
A8.23. COMMON MAINTENANCE PRACTICES
TR: APPLICABLE AIRCRAFT TO’S
A8.23.1. Inspect/operate portable external electrical power unit
- - - -
A8.23.2. Inspect/use ground maintenance stands - - - -
A8.23.3. Dropped Object Prevention Program (DOPP) - - - -
A8.23.4. Defensive Systems (DS) familiarization (on applicable aircraft)
- - - -
A8.23.5. Operate
A8.23.5.1.. Maint platform universal electric (scissors stand)
TR: 35A4-2-61-1
- - - -
A8.23.5.2. Platform servicing (Simmon)
TR: 35D34-31-1
- - - -
A8.23.5.3. Generator set, diesel (-86)
TR: 35C2-3-469-11
- - - -
A8.23.5.4. Air conditioner, diesel driven (MA-31)
TR: 35E9-9-61
- - - -
A8.23.5.5. Heater duct type, portable (diesel)
TR: 35E7-2-11-11
- - - -
A8.23.5.6. Floodlight set (NF-2)
TR: 35F5-5-11-61
- - - -
A8.23.5.7. Fuselage/wing access entry - - - -
C-17 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
158Attachment 8
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
TR: 1C-17A-2-00JG series
A8.23.5.8. Vert stab entry
TR: 1C-17A-2-00JG series
- - - -
A8.23.5.9. Horizontal stab entry
TR: 1C-17A-2-00JG series
- - - -
A8.23.5.10. Vert. stab exit
TR: 1C-17A-2-00JG series
- - - -
A8.23.5.11. Underfloor maint. tunnel entry
TR: 1C-17A-2-00JG series
- - - -
A8.23.5.12. Underfloor maint. tunnel exit
TR: 1C-17A-2-00JG series
- - - -
A8.23.5.13. Power off underfloor maint. tunnel entry
TR: 1C-17A-2-00JG series
- - - -
A8.23.5.14. Power off underfloor maint. tunnel exit
TR: 1C-17A-2-00JG series
- - - -
A8.23.5.15. Connect/disconnect grnd a/c unit
TR: 1C-17A-2-10JG series
- - - -
A8.23.5.16. Connect/disconnect ext. hyd. power
TR: 1C-17A-2-10JG series
- - - -
A8.23.5.17. Connect/disconnect ext. pneumatic air
TR: 1C-17A-2-10JG series
- - - -
C-130 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
159Attachment 9
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
ATTACHMENT 9
NOTE 1: In addition to attachment 2, the tasks and knowledge in attachment 9 will be performed by personnel assigned to maintain C-130 aircraft.
NOTE 2: Users are responsible for annotating training references to identify current references pending STS revision.
NOTE 3: Items marked in columns 2a or 2b marked with a (*R) are optional core tasks for ANG and AFRC.
NOTE 4: Address comments and recommended changes through Unit Training Managers to the MAJCOM Maintenance Training Manager @ HQAMC/LGMMT, 402 Scott Drive Unit 2A2, Scott AFB, IL 62225-5308; or call DSN 576-4787. MAJCOM Training and Functional Managers forward inputs tothe AETC Training Manager, DSN 736-2772.
A9.1. AC POWER SYSTEM
TR: Applicable C-130 TOs, 8 series component TOs
A9.1.1. Operational fundamentals - - - -
A9.1.2. Operational check * - - - -
A9.1.3. Troubleshoot - - - -
A9.1.3.1 AC Power System - - - -
A9.1.3.2 Bearing Fail System - - - -
A9.1.4. Inspect System Components * - - - -
A9.1.5. Remove components
A9.1.5.1. Generator control panel - - - -
A9.1.5.2. Voltage regulator - - - -
A9.1.5.3. Frequency-sensitive relay - - - -
A9.1.5.4. Inverter - - - -
A9.1.5.5. Bus tie contactor - - - -
A9.1.5.6. Generator control unit - - - -
A9.1.5.7. Bus switching system components - - - -
A9.1.5.8. Engine generator - - - -
A9.1.5.9. Other system components - - - -
A9.1.6. Repair components - - - -
A9.1.7. Install components
A9.1.7.1. Generator control panel - - - -
A9.1.7.2. Voltage regulator - - - -
A9.1.7.3. Frequency-sensitive relay - - - -
A9.1.7.4. Inverter - - - -
A9.1.7.5. Bus tie contactor - - - -
A9.1.7.6. Generator control unit - - - -
A9.1.7.7. Bus switching system components - - - -
A9.1.7.8. Generator, engine - - - -
A9.1.7.9. Other system components - - - -
A9.1.8. Component location - - - -
A9.1.9. Bench check components - - - -
C-130 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
160Attachment 9
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A9.2. DC POWER SYSTEM
TR: Applicable C-130 TOs, 8 series component TOs
A9.2.1. Operational fundamentals - - - -
A9.2.2. Operational check * - - - -
A9.2.3. Troubleshoot - - - -
A9.2.4. Inspect System Components * - - - -
A9.2.5. Remove components
A9.2.5.1. Transformer rectifier unit - - - -
A9.2.5.2. Reverse current relay - - - -
A9.2.5.3. Battery system components - - - -
A9.2.5.4. Other system components - - - -
A9.2.6. Install components
A9.2.6.1. Transformer rectifier - - - -
A9.2.6.2. Reverse current relay - - - -
A9.2.6.3. Battery system components - - - -
A9.2.6.4. Other system components - - - -
A9.3. EXTERNAL POWER SYSTEM
TR: Applicable C-130 TOs, 8 series component TOs
A9.3.1. Operational fundamentals - - - -
A9.3.2. Operational check - - - -
A9.3.3. Apply external power - - - -
A9.3.4. Troubleshoot System - - - -
A9.3.5. Inspect System Components * - - - -
A9.3.6. Remove components
A9.3.6.1. External power receptacle - - - -
A9.3.6.2. External power contactor - - - -
A9.3.6.3. Other system components - - - -
A9.3.7. Repair components - - - -
A9.3.8. Install components
A9.3.8.1. External power receptacle - - - -
A9.3.8.2. External power contactor - - - -
A9.3.8.3. Other system components - - - -
A9.3.9. Component location - - - -
A9.3.10. Bench check components - - - -
A9.4. APU/GTC POWER SYSTEM
TR: Applicable C-130 TO’s
A9.4.1. Operational fundamentals - - - -
C-130 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
161Attachment 9
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A9.4.2. Operational check - - - -
A9.4.3. Troubleshoot - - - -
A9.4.4. Inspect System Components - - - -
A9.4.5. Remove components - - - -
A9.4.6. Repair components - - - -
A9.4.7. Install components - - - -
A9.5. AIR TURBINE SYSTEM (ATM)
A9.5.1. Operational fundamentals - - - -
A9.5.2. System Operational check - - - -
A9.5.2.1. Bus off warning operational check - - - -
A9.5.3. Troubleshoot - - - -
A9.5.4. Inspect System Components * - - - -
A9.5.5. Remove components
A9.5.5.1. ATM assembly - - - -
A9.5.5.2. ATM/APU generator - - - -
A9.5.5.3. Shutoff valve - - - -
A9.5.5.4. Modulation valve - - - -
A9.5.5.5. Cooling fan - - - -
A9.5.5.6. Solenoid - - - -
A9.5.5.7. Filter - - - -
A9.5.5.8. Bus tie/generator line contactor - - - -
A9.5.5.9. Bus off warning relay - - - -
A9.5.6. Repair components - - - -
A9.5.7. Install components
A9.5.7.1. ATM assembly - - - -
A9.5.7.2. ATM/APU generator - - - -
A9.5.7.3. Shutoff valve - - - -
A9.5.7.4. Modulation valve - - - -
A9.5.7.5. Cooling fan - - - -
A9.5.7.6. Solenoid - - - -
A9.5.7.7. Filter - - - -
A9.5.7.8. Bus tie/generator line contactor - - - -
A9.5.7.9. Bus off warning relay - - - -
A9.5.7.10. Drain and service oil - - - -
A9.6. LIGHTING SYSTEM
TR: Applicable C-130 TOs, 8 series component TOs
A9.6.1. Operational fundamentals - - - -
C-130 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
162Attachment 9
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A9.6.2. Operational check
A9.6.2.1. External lighting * - - - -
A9.6.2.2. Internal lighting - - - -
A9.6.2.2.1. Flight-deck lighting - - - -
A9.6.2.2.2. Cargo compartment lighting - - - -
A9.6.2.2.3. Other internal lighting - - - -
A9.6.3. Troubleshoot Lighting Systems - - - -
A9.6.4. Inspect Lighting Systems * - - - -
A9.6.5. Remove components
A9.6.5.1. Loading light - - - -
A9.6.5.2. Instrument panel eyebrow light - - - -
A9.6.5.3. Wingtip light - - - -
A9.6.5.4. Variable AC light transformer - - - -
A9.6.5.5. DC light rheostat - - - -
A9.6.5.6. NVG Light Assemblies - - - -
A9.6.5.7. NVIS Receptacle - - - -
A9.6.5.8. NVG Transfer Unit - - - -
A9.6.5.9. NVG Lighting Control Box - - - -
A9.6.6. Repair components - - - -
A9.6.7. Install components
A9.6.7.1. Loading light - - - -
A9.6.7.2. Instrument panel eyebrow light - - - -
A9.6.7.3. Wingtip light - - - -
A9.6.7.4. Variable AC light transformer - - - -
A9.6.7.5. DC light rheostat - - - -
A9.6.7.6. NVG Light Assemblies - - - -
A9.6.7.7. NVIS Receptacle - - - -
A9.6.7.8. NVG Transfer Unit - - - -
A9.6.7.9. NVG Lighting Control Box - - - -
A9.7. LANDING GEAR SYSTEM
TR: Applicable C-130 TOs, 8 series component TOs
A9.7.1. Operational fundamentals - - - -
A9.7.2. Operational check - - - -
A9.7.3. Troubleshoot System * - - - -
A9.7.4. Inspect System Components * - - - -
A9.7.5. Remove components - - - -
A9.7.6. Install components - - - -
C-130 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
163Attachment 9
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A9.8. ANTI-SKID SYSTEM
TR: Applicable C-130 TOs, 8 series component TOs
A9.8.1. Operational fundamentals - - - -
A9.8.2. Operational check - - - -
A9.8.3. Troubleshoot System * - - - -
A9.8.4. Inspect System Components * - - - -
A9.8.5. Remove components
A9.8.5.1. Anti-skid control box * - - - -
A9.8.5.2. Wheel transducer - - - -
A9.8.5.3. Other system components - - - -
A9.8.7. Install components
A9.8.7.1. Anti-skid control box * - - - -
A9.8.7.2. Wheel transducer - - - -
A9.8.7.3. Other system components - - - -
A9.9. PRIMARY FLIGHT CONTROL SYSTEM
TR: Applicable C-130 TOs, 8 series component TOs
A9.9.1. Operational fundamentals - - - -
A9.9.2. Operational check
A9.9.2.1. Aileron/Rudder Trim - - - -
A9.9.2.2. Elevator Trim - - - -
A9.9.3. Troubleshoot - - - -
A9.9.4. Inspect System Components - - - -
A9.9.5. Remove components
A9.9.5.1. Elevator trim yoke switch - - - -
A9.9.5.2. Elevator trim selector switch - - - -
A9.9.5.3. Rudder/aileron trim switch - - - -
A9.9.5.4. Other system components - - - -
A9.9.6. Install components
A9.9.6.1. Elevator trim yoke switch - - - -
A9.9.6.2. Elevator trim selector switch - - - -
A9.9.6.3. Rudder/aileron trim switch - - - -
A9.9.6.4. Other system components - - - -
A9.10. SECONDARY FLIGHT CONTROL SYSTEM
TR: Applicable C-130 TOs, 8 series component TOs
A9.10.1. Operational fundamentals - - - -
A9.10.2. Operational check flaps - - - -
C-130 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
164Attachment 9
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A9.10.3. Troubleshoot flaps - - - -
A9.10.4. Inspect System Components - - - -
A9.10.5. Remove components
A9.10.5.1. Flap assemetry brake switches - - - -
A9.10.5.2. Flap motor limit switches - - - -
A9.10.5.3. Flap motor warning switches - - - -
A9.10.5.4. Flap position warning switches - - - -
A9.10.6. Repair components - - - -
A9.10.7. Install components
A9.10.7.1. Flap assemetry brake switches - - - -
A9.10.7.2. Flap motor limit switches - - - -
A9.10.7.3. Flap motor warning switches - - - -
A9.10.7.4. Flap position warning switches - - - -
A9.11. OVERHEAT/FIRE WARNING SYSTEM
TR: Applicable C-130 Tos, 8 series component TOs
A9.11.1. Operational fundamentals - - - -
A9.11.2. Operational check
A9.11.2.1. Engine overheat/fire warning * - - - -
A9.11.2.2. GTC/APU/overheat/fire warning * - - - -
A9.11.2.3. Nacelle overheat * - - - -
A9.11.2.4. Turbine overheat * - - - -
A9.11.3. Troubleshoot
A9.11.3.1. Overheat/fire warning * - - - -
A9.11.3.2. Turbine overheat * - - - -
A9.11.3.3. Nacelle overheat * - - - -
A9.11.4. Inspect System Components * - - - -
A9.11.5. Remove components
A9.11.5.1. Thermostat - - - -
A9.11.5.2. Fire/Overheat loop - - - -
A9.11.5.3. Fire Warning Control Box - - - -
A9.11.5.4. Overheat detectors - - - -
A9.11.5.5. Turbine overheat wiring harness - - - -
A9.11.6. Repair components - - - -
A9.11.7. Install components
A9.11.7.1. Thermostat - - - -
A9.11.7.2. Fire/Overheat loop - - - -
A9.11.7.3. Fire Warning Control Box - - - -
C-130 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
165Attachment 9
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A9.11.7.4. Overheat detectors - - - -
A9.11.7.5. Turbine overheat wiring harness - - - -
A9.11.8. Bench check components - - - -
A9.12. FIRE EXTINGUISHING SYSTEM
TR: Applicable C-130 TOs, 8 series component TOs
A9.12.1. Operational fundamentals - - - -
A9.12.2. Operational check - - - -
A9.12.3. Troubleshoot Systems - - - -
A9.12.4. Inspect System Components * - - - -
A9.12.5. Remove components
A9.12.5.1. Squib * - - - -
A9.12.5.2. Agent bottle - - - -
A9.12.5.3. Directional control valves - - - -
A9.12.5.4. System plumbing - - - -
A9.12.6. Install components
A9.12.6.1. Squib - - - -
A9.12.6.2. Agent bottle - - - -
A9.12.6.3. Directional control valves - - - -
A9.12.6.4. System plumbing - - - -
A9.12.7. Bench check components - - - -
A9.13. MASTER CAUTION/WARNING SYSTEM
TR: Applicable C-130 TOs, 8 series component TOs
A9.13.1. Operational fundamentals - - - -
A9.13.2. Operational check of Panel Assembly - - - -
A9.13.3. Troubleshoot - - - -
A9.13.4. Inspect System Components - - - -
A9.13.5. Remove components
A9.13.5.1 Dimmer Unit - - - -
A9.13.5.2 Control Box - - - -
A9.13.5.3 Light Assembly - - - -
A9.13.6. Install components
A9.13.6.1 Dimmer Unit - - - -
A9.13.6.2 Control Box - - - -
A9.13.6.3 Light Assembly - - - -
A9.14. CARGO DOOR CONTROL AND WARNING SYSTEM
TR: Applicable C-130 TOs, 8 series component
C-130 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
166Attachment 9
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
TOs
A9.14.1. Operational fundamentals - - - -
A9.14.2. Operational check
A9.14.2.1. Cargo Ramp/Door * - - - -
A9.14.2.2. ADS - - - -
A9.14.3. Troubleshoot System - - - -
A9.14.4. Inspect System Components - - - -
A9.14.5. Remove components
A9.14.5.1. Ramp switch - - - -
A9.14.5.2. Door switch - - - -
A9.14.6. Install components
A9.14.6.1. Ramp switch - - - -
A9.14.6.2. Door switch - - - -
A9.14.7. Adjust switches
A9.14.7.1. Ramp Switch - - - -
A9.14.7.2. Door Switch - - - -
A9.15. START AND IGNITION SYSTEM
TR: Applicable C-130 TOs, 8 series component TOs
A9.15.1. Operational fundamentals - - - -
A9.15.2. Operational check - - - -
A9.15.3. Auxiliary generator - - - -
A9.15.4. Troubleshoot System - - - -
A9.15.5. Inspect System Components - - - -
A9.15.6. Remove components
A9.15.6.1. Starter control switch - - - -
A9.15.6.2. Throttle ignition switch - - - -
A9.15.6.3. Low speed ground idle switch - - - -
A9.15.7. Install components
A9.15.7.1. Starter control switch - - - -
A9.15.7.2. Throttle ignition switch - - - -
A9.15.7.3. Low speed ground idle switch - - - -
A9.16. FUEL WARNING AND CONTROL SYSTEM
TR: Applicable C-130 TOs; 8 series component TOs
A9.16.1. Operational fundamentals - - - -
A9.16.2. Operational check - - - -
A9.16.3. Troubleshoot System - - - -
A9.16.4. Inspect System Components - - - -
C-130 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
167Attachment 9
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A9.16.5. Remove components - - - -
A9.16.6. Repair components - - - -
A9.16.7. Install components - - - -
A9.16.8. Bench check components - - - -
A9.17. NESA ANTI-ICING SYSTEM
TR: Applicable C-130 TOs; 8 series component TOs
A9.17.1. Operational fundamentals - - - -
A9.17.2. Operational check - - - -
A9.17.3. Attach wire to taps on transformer * - - - -
A9.17.4. Troubleshoot System - - - -
A9.17.5. Inspect System Components * - - - -
A9.17.6. Remove components
A9.17.6.1. Power transformer - - - -
A9.17.6.2. NESA window leads and hardware - - - -
A9.17.7. Install components
A9.17.7.1. Power transformer - - - -
A9.17.7.2. NESA window leads and hardware - - - -
A9.18. BLEED AIR DISTRIBUTION SYSTEM
TR: Applicable C-130 TOs, 8 series component TOs
A9.18.1. Operational fundamentals - - - -
A9.18.2. Operational check * - - - -
A9.18.3. Troubleshoot System * - - - -
A9.18.4. Inspect System Components - - - -
A9.18.5. Remove components
A9.18.5.1. Engine shutoff valve - - - -
A9.18.5.2. Wing anti-ice valve - - - -
A9.18.5.3. Bleed air ducts and clamps - - - -
A9.18.5.4. Thermostat - - - -
A9.18.5.5. Other system components - - - -
A9.18.6. Install components
A9.18.6.1. Engine shutoff valve - - - -
A9.18.6.2. Wing anti-ice valve - - - -
A9.18.6.3. Bleed air duct and clamp - - - -
A9.18.6.4. Thermostat - - - -
A9.18.6.5. Other system components - - - -
A9.18.7. Perform leakage checks * - - - -
A9.18.8. Perform bleed air decay check * - - - -
C-130 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
168Attachment 9
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A9.19. RADOME ANTI-ICING SYSTEM
TR: Applicable C-130 TOs, 8 series component TOs
A9.19.1. Operational fundamentals - - - -
A9.19.2. Operational check - - - -
A9.19.3. Troubleshoot System - - - -
A9.19.4. Troubleshoot Monitoring System - - - -
A9.19.5. Inspect System Components - - - -
A9.19.6. Remove components
A9.19.6.1. Anti-ice valve - - - -
A9.19.6.2. Thermal-switches - - - -
A9.19.6.3. Anti-ice solenoid - - - -
A9.19.6.4. Anti-ice regulator - - - -
A9.19.6.5. Glycol tank components - - - -
A9.19.6.6. Monitor Indicators - - - -
A9.19.6.7. Pressure Transducer - - - -
A9.19.6.8. Resistance Temperature Detector - - - -
A9.19.7. Install components
A9.19.7.1. Anti-ice valve - - - -
A9.19.7.2. Thermoswitches - - - -
A9.19.7.3. Radome anti-ice solenoid - - - -
A9.19.7.4. Radome anti-ice regulator - - - -
A9.19.7.5. Glycol tank components - - - -
A9.19.7.6. Monitor Indicators - - - -
A9.19.7.7. Pressure Transducer - - - -
A9.19.7.8. Resistance Temperature Detector - - - -
A9.19.8 Calibrate System - - - -
A9.20. WING AND EMPENNAGE ANTI-ICING SYSTEM
TR: Applicable C-130 TOs, 8 series components TOs
A9.20.1. Operational fundamentals - - - -
A9.20.2. Operational check * - - - -
A9.20.3. Troubleshoot System - - - -
A9.20.4. Inspect System Component - - - -
A9.20.5. Remove components - - - -
A9.20.6. Install components - - - -
A9.21. ICE DETECTION SYSTEM
TR: Applicable C-130 TOs, 8 series components
C-130 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
169Attachment 9
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
TOs
A9.21.1. Operational fundamentals - - - -
A9.21.2. Operational check - - - -
A9.21.3. Troubleshoot System - - - -
A9.21.4. Inspect System Components - - - -
A9.21.5. Remove components
A9.21.5.1. Ice detector - - - -
A9.21.5.2. Interpreter - - - -
A9.21.5.3. Propeller de-ice timer - - - -
A9.21.5.4. Other System Components - - - -
A9.21.6. Install components
A9.21.6.1. Ice detector - - - -
A9.21.6.2. Interpreter - - - -
A9.21.6.3. Propeller de-ice timer - - - -
A9.21.5.4. Other System Components - - - -
A9.22. UNDERFLOOR HEAT SYSTEM
TR: Applicable C-130 TOs, 8 series components TOs
A9.22.1. Operational fundamentals - - - -
A9.22.2. Operational check - - - -
A9.22.3. Troubleshoot System - - - -
A9.22.4. Inspect System Components - - - -
A9.22.5. Remove components
A9.22.5.1. Shutoff valve - - - -
A9.22.5.2. Diverter valve - - - -
A9.22.5.3. Thermostat - - - -
A9.22.5.4. Recirculating fan - - - -
A.9.20.5.5 Other System Components - - - -
A9.22.6. Install components
A9.22.6.1. Shutoff valve - - - -
A9.22.6.2. Diverter valve - - - -
A9.22.6.3. Thermostat - - - -
A9.22.6.4. Recirculating fan - - - -
A.9.20.6.5 Other System Components - - - -
A9.23. AIR CONDITIONING SYSTEM
TR: Applicable C-130 TOs; 8 series component TOs
A9.23.1. Operational fundamentals - - - -
A9.23.2. Operational check * - - - -
C-130 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
170Attachment 9
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A9.23.3. Troubleshoot System * - - - -
A9.23.4. Inspect System Components * - - - -
A9.23.5. Remove components
A9.23.5.1. Flow control valve - - - -
A9.23.5.2. Diverter valve pressure controller - - - -
A9.23.5.3. Water separator sock * - - - -
A9.23.5.4. Temperature control valve - - - -
A9.23.5.5. Water separator - - - -
A9.23.5.6. Water separator anti-ice valve - - - -
A9.23.5.7. Auxiliary vent valve - - - -
A9.23.5.8. Cooling turbine - - - -
A9.23.5.9. Heat exchanger - - - -
A9.23.5.10. Ram air duct - - - -
A9.23.5.11. Refrigeration unit - - - -
A9.23.5.12. Temperature control boxes - - - -
A.9.21.5.13 Other system components - - - -
A9.23.6. Repair components - - - -
A9.23.7. Install components
A9.23.7.1. Flow control valve - - - -
A9.23.7.2. Diverter valve pressure controller - - - -
A9.23.7.3. Water separator sock * - - - -
A9.23.7.4. Temperature control valve - - - -
A9.23.7.5. Water separator - - - -
A9.23.7.6. Water separator anti-ice valve - - - -
A9.23.7.7. Auxiliary vent valve - - - -
A9.23.7.8. Cooling turbine - - - -
A9.23.7.9. Heat exchanger - - - -
A9.23.7.10. Ram air duct - - - -
A9.23.7.11. Refrigeration unit - - - -
A9.23.7.12. Temperature control boxes - - - -
A.9.23.7.13 Other system components - - - -
A9.23.8. Perform leakage checks * - - - -
A9.23.9. Bench check components - - - -
A9.23.10. Service cooling turbine - - - -
A9.23.11. Adjust flight deck flow valve cabin assembly - - - -
A9.24. PRESSURIZATION SYSTEM
TR: Applicable C-130 TOs; 8 series component TOs
C-130 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
171Attachment 9
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A9.24.1. Operational fundamentals - - - -
A9.24.2. Operational check *R - - - -
A9.24.3. Troubleshoot
A9.24.3.1 Pressurization System * - - - -
A9.24.3.2 Overboard Vent System * - - - -
A9.24.4. Inspect System Components * - - - -
A9.24.5. Remove components
A9.24.5.1. Pressure controller - - - -
A9.24.5.2. Outflow valve - - - -
A9.24.5.3. Pneumatic relay - - - -
A9.24.5.4. Safety valve - - - -
A9.24.5.5. Overboard Vent outflow valve - - - -
A9.24.5.6. Overboard vent vacuum regulator - - - -
A9.24.5.7. Overboard Vent pneumatic relay - - - -
A9.24.5.8. Filters - - - -
A9.24.6. Repair components - - - -
A9.24.7. Install components
A9.24.7.1. Pressure controller - - - -
A9.24.7.2. Outflow valve - - - -
A9.24.7.3. Pneumatic relay - - - -
A9.24.7.4. Safety valve - - - -
A9.24.7.5. Overboard Vent outflow valve - - - -
A9.24.7.6. Overboard vent vacuum regulator - - - -
A9.24.7.7. Overboard Vent pneumatic relay - - - -
A9.24.7.8. Filters - - - -
A9.24.8. Bench check components - - - -
A9.24.9. Perform pressure decay check * - - - -
A9.25. LIQUID OXYGEN SYSTEM
TR: AFOSH standards; TOs 15X1-1, 42B5-1-2,42E1-1-1, Applicable C-130 TOs
A9.25.1. Operational fundamentals - - - -
A9.25.2. Operational check * - - - -
A9.25.3. Troubleshoot System - - - -
A9.25.4. Inspect System Components * - - - -
A9.25.5. Purge system * - - - -
A9.25.6. Remove components
A9.25.6.1. Oxygen regulator * - - - -
A9.25.6.2. Converter - - - -
C-130 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
172Attachment 9
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A9.25.6.3. Buildup/vent valve - - - -
A9.25.6.4. Shutoff drain valve - - - -
A9.25.6.5. Heat Exchanger - - - -
A9.25.7. Install components
A9.25.7.1. Oxygen regulator * - - - -
A9.25.7.2. Converter - - - -
A9.25.7.3. Buildup/vent valve - - - -
A9.25.7.4. Shutoff drain valve - - - -
A9.25.7.5. Heat Exchanger - - - -
A9.25.8. Perform leak check * - - - -
A9.25.9. Clean components * - - - -
A9.26. MISCELLANEOUS SYSTEMS
TR: Applicable C-130 TOs, 8 series component TOs
A9.26.1. Propeller feather electrical
A9.26.1.1. Operational check - - - -
A9.26.1.2. Troubleshoot System - - - -
A9.26.1.3. Inspect System Components - - - -
A9.26.1.4. Remove Feather button - - - -
A9.26.1.5. Install Feather button - - - -
A9.26.2. Static line retriever system
A9.26.2.1. Operational check - - - -
A9.26.2.2. Troubleshoot System - - - -
A9.26.2.3. Inspect System Components - - - -
A9.26.2.4. Remove components
A9.26.2.4.1. Static line current limiter - - - -
A9.26.2.4.2. Static line switches - - - -
A9.26.2.5. Repair components - - - -
A9.26.2.6. Install components
A9.26.2.6.1. Static line current limiter - - - -
A9.26.2.6.2. Static line switches - - - -
A9.26.2.7 Bench Check Components - - - -
A9.26.3. Radar Wave guide SystemTR: Applicable Acft TO’s
A9.26.3.1. Perform System Pressure check - - - -
A9.26.3.2 Remove pressure regulator - - - -
A9.26.3.3 Install pressure regulator - - - -
A9.26.4 URRASI
TR: Applicable TO’s
C-130 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
173Attachment 9
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A9.26.4.1 Operational Fundamentals - - - -
A9.26.4.2 Operational Check - - - -
A9.26.4.3 Troubleshoot System - - - -
A9.26.4.4 Inspect System Components - - - -
A9.26.4.5 Remove Components - - - -
A9.26.4.6 Install Components - - - -
A26.5. Aerial Refueling System
TR: Applicable TO’s
A9.26.5.1 Operational Fundamentals - - - -
A9.26.5.2 Operational Check - - - -
A9.26.5.3 Troubleshoot System - - - -
A9.26.5.4 Inspect System Components - - - -
A9.26.5.5 Remove Components - - - -
A9.26.5.6 Install Components - - - -
A9.27. COMMON MAINTENANCE PRACTICES
TR:
A9.27.1 Dropped Object Program (DOPP) - - - -
A9.27.2 Defensive System (DS) familiarization (on applicable aircraft)
- - - -
A9.27.3 Team communications - - - -
A9.28. C-130 J Model Applicable Task
TR: Applicable TO’s
A9.28.1. AC POWER SYSTEM
A9.28.1.1. Operational Fundamentals - - - -
A9.28.1.2. Operational Check of AC Power System using Communication Navigation Identification Management Unit (CNI-MU)
- - - -
A9.28.2 Remove Components
A9.28.2.1 Overhead Electrical Control Panel - - - -
A9.28.2.2 Engine Generator Magnetic Indicator Plug - - - -
A9.28.2.3 Bulkhead Battery Panel Assembly - - - -
A9.28.3 Install Components
A9.28.3.1 Overhead Electrical Control Panel - - - -
A9.28.3.2 Engine Generator Magnetic Indicator Plug - - - -
A9.28.3.3 Bulkhead Battery Panel Assembly - - - -
A9.29 DC POWER SYSTEM
A9.29.1 Operational Fundamentals - - - -
A9.29.2 Remove components
A9.29.2.1 Low Voltage Power Supply (LVPS) - - - -
C-130 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
174Attachment 9
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A9.29.2.2 Power Panel Distribution Unit (PPDU) - - - -
A9.29.2.3 DC Power Diodes - - - -
A9.29.3. Install Components
A9.29.3.1 Low Voltage Power Supply (LVPS) - - - -
A9.29.3.2 Power Panel Distribution Unit (PPDU) - - - -
A9.29.3.3 DC Power Diodes - - - -
A9.29.4. Load Electronic C/B Unit (ECBU) Software * - - - -
A9.29.5. Perform ECBU IBIT * - - - -
A9.29.6. Manipulate ECB’s using AMU (Avionics Management Unit)
* - - - -
A9.29.7. Manipulate ECB’s using CNI-MU * - - - -
A9.29.8. Manipulate ECB’s using Portable Maintenance Aid (PMA)
- - - -
A9.30 EXTERNAL POWER SYSTEM
A9.30.1 Operational Fundamentals - - - -
A9.30.2 Load Operational Maintenance Program (OMP) with external power
* - - - -
A9.30.3 Load Operational Maintenance Program (OMP) with battery power
- - - -
A9.31 APU POWER SYSTEM
A9.31.1 Operational fundamentals - - - -
A9.31.2 Operational check using CNI-MU - - - -
A9.32 LIGHTING SYSTEM
A9.32.1 Operational Fundamentals - - - -
A9.32.2 Operate Copilots lighting using CNI-MU - - - -
A9.32.3 Operate Pilots lighting using CNI-MU - - - -
A9.32.4 Operate External lighting using CNI-MU - - - -
A9.32.5 Operate Lighting control using AMU and HDD - - - -
A9.32.6 Operational Check of Emergency Exit Lighting System
- - - -
A9.32.7 Remove Component
A9.32.7.1 Multi-Channel Dimming Unit(MCDU) - - - -
A9.32.7.2 Dome Light Dimming Unit (DLDU) - - - -
A9.32.7.3 Emergency Exit Light Inertia Switch - - - -
A9.32.7.4 Emergency Exit Light Batteries - - - -
A9.32.8 Install Component
A9.32.8.1 Multi-Channel Dimming Unit(MCDU) - - - -
A9.32.8.2 Dome Light Dimming Unit (DLDU) - - - -
A9.32.8.3 Emergency Exit Light Inertia Switch - - - -
A9.32.8.4 Emergency Exit Light Batteries - - - -
C-130 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
175Attachment 9
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A9.33 LANDING GEAR SYSTEM
A9.33.1 Operational Fundamentals - - - -
A9.33.2 Operational Check using CNI-MU - - - -
A9.34 ANTI-SKID SYSTEM/WHEEL BRAKE SYSTEM
A9.34.1 Operational Fundamentals - - - -
A9.34.2 Operational Check using CNI-MU - - - -
A9.34.3 Perform IBIT of system - - - -
A9.35 PRIMARY FLIGHT CONTROL SYSTEM
A9.35.1 Operational Fundamentals - - - -
A9.35.2 Troubleshoot - - - -
A9.36 SECONDARY FLIGHT CONTROL SYSTEM
A9.36.1 Operational Fundamentals - - - -
A9.36.2 Troubleshoot - - - -
A9.37. OVERHEAT/FIRE WARNING SYSTEM
A9.37.1 Operational Fundamentals - - - -
A9.37.2 Operational Check of Fire Overheat Controller (FODS)
* - - - -
A9.37.3 Perform IBIT of FODS Controller - - - -
A9.38 SMOKE DETECTION SYSTEM
A9.38.1 Operational Fundamentals - - - -
A9.38.2 Operational Check using AMU - - - -
A9.38.3 Remove Smoke Detector - - - -
A9.38.4 Install Smoke Detector - - - -
A.9.39 FIRE EXTINGUISHING SYSTEM
A.9.39.1 Operational Fundamentals - - - -
A9.40 SYSTEM INTEGRATION AND DISPLAY
A9.40.1 Operational Fundamentals - - - -
A9.40.2 Operational Check of BAU (Type I or II) - - - -
A9.40.3 Remove Component
A9.40.3.1 Bus Adapter Unit (BAU) - - - -
A9.40.3.2 Bus Interface Unit (BIU) - - - -
A9.40.4 Install Component
A9.40.4.1 Bus Adapter Unit (BAU) - - - -
A9.40.4.2 Bus Interface Unit (BIU) - - - -
A9.41 CARGO DOOR CONTROLAND WARNING SYSTEM
A9.41.1 Operational Fundamentals - - - -
A9.41.2 Operational Check using CNI-MU - - - -
C-130 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
176Attachment 9
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A9.42 BLEED AIR ENVIRONMENTAL CONTROL SYSTEM (BAECS)
A9.42.1 Operational Fundamentals - - - -
A9.42.2 Operational Check of Bleed Air EnvironmentalController
- - - -
A9.42.3 Operational Check of Wing/Empennage Anti-ice System
- - - -
A9.42.4 Operate Bleed Air Valves using CNI-MU - - - -
A9.42.5 Perform IBIT of BAECS Anti-Ice System - - - -
A9.42.6 Remove
A9.42.6.1 BAECS CONTROLLER - - - -
A9.42.6.2 Pneumatic Controller - - - -
A9.42.6.3 Temperature Sensor - - - -
A9.42.6.4 Pressure Sensor - - - -
A9.42.7 Install
A9.42.7.1 BAECS CONTROLLER - - - -
A9.42.7.2 Pneumatic Controller - - - -
A9.42.7.3 Temperature Sensor - - - -
A9.42.7.4 Pressure Sensor - - - -
A9.43 ICE PROTECTION
A9.43.1 Operational Fundamentals - - - -
A9.43.2 Operational check of De-Ice Boot - - - -
A9.43.3 Calibrate De-ice Timer Unit (DITU) - - - -
A9.43.4 Operate Ice Protection System using CNI-MU (NESA, WING/EMP, PROP)
- - - -
A9.44 AIR CONDITIONING SYSTEM
A9.44.1 Operational Fundamentals - - - -
A9.44.2 Operational Check using CNI-MU - - - -
A9.45 PRESSURIZATION
A9.45.1 Operational Fundamentals - - - -
A9.45.2 Operational Check using CNI-MU * - - - -
A9.45.3. Remove Components
A9.45.3.1. Pressurization Control Panel - - - -
A9.45.3.2. Cabin Pressure Controller - - - -
A9.45.3.3. Outflow Valve Servo - - - -
A9.45.3.4. Cabin Pressure Transducer - - - -
A.9.45.4. Install Components
A.9.45.4.1. Pressurization Control Panel - - - -
A.9.45.4.2. Cabin Pressure Controller - - - -
C-130 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
177Attachment 9
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A.9.45.4.3. Outflow Valve Servo - - - -
A.9.45.4.4. Cabin Pressure Transducer - - - -
A.9.45.5. Cabin Pressure Controller IBIT - - - -
A9.46 COMMON MAINTENACE PRACTICES
A9.46.1 Access maintenance messages using AMU/HDD * - - - -
A9.46.2 Operate Portable Maintenance Aid (PMA) * - - - -
A9.46.3 Interpret Fault Isolation codes using Ground Maintenance System (GMS)
* - - - -
A9.46.4 Perform Data Bus Test Points (DBTP) using PMA * - - - -
A9.46.5 Removal and Installation Fundamentals
A9.46.5.1 Type 1 Line Replaceable Units - - - -
A9.46.5.2 Type 2 Line Replaceable Units - - - -
A9.46.5.3 Type 3 Line Replaceable Units - - - -
A9.46.5.4 Type 4 Line Replaceable Units - - - -
A9.46.5.5 Type 5 Line Replaceable Units - - - -
A.9.46.6 ENHANCED CARGO HANDLING SYSTEM
A.9.46.6.1. Operational Fundamentals - - - -
A.9.46.6.2. Operational Check of ECHS - - - -
A.9.46.7. Remove Component
A.9.46.7.1. Pallet Lock Control Unit (PLCU) - - - -
A.9.46.7.2. Multi-Function Color Display (MFCD) - - - -
A.9.46.8. Install Component
A.9.46.8.1. Pallet Lock Control Unit (PLCU) - - - -
A.9.46.8.2. Multi-Function Color Display (MFCD) - - - -
C-141 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
178Attachment 10
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
ATTACHMENT 10
NOTE 1: In addition to attachment 2, the tasks and knowledge in attachment 6 will be performed by personnel assigned to maintain C-141 aircraft.
NOTE 2: Users are responsible for annotating training references to identify current references pending STS revision.
NOTE 3: Items marked in columns 2a or 2b marked with a (*R) are optional core tasks for ANG and AFRC.
NOTE 4: Address comments and recommended changes through Unit Training Managers to the MAJCOM Maintenance Training Manager @ HQ AMC/LGMMT, 40Drive Unit 2A2, Scott AFB, IL 62225-5308; or call DSN 576-4787. MAJCOM Training and Functional Managers forward inputs to the AETC Training Manager,
DSN 736-2772.
A10.1. METERS AND TESTERS
TR: Applicable 33 series TOs
A10.1.1. Use ECS tester - - - -
A10.2. AC POWER SYSTEM
TR: Applicable C-141 TOs, 8 series component TOs
A10.2.1. Operational fundamentals - - - -
A10.2.2. Operational check * - - - -
A10.2.3. Troubleshoot - - - -
A10.2.4. Inspect * - - - -
A10.2.5. Remove components
A10.2.5.1. Generator control unit * - - - -
A10.2.5.2. Load controller * - - - -
A10.2.5.3. Bus tie contactor * - - - -
A10.2.5.4. Bus off indication relay * - - - -
A10.2.5.5. Other system components - - - -
A10.2.6. Repair components - - - -
A10.2.7. Install components
A10.2.7.1. Generator control unit * - - - -
A10.2.7.2. Load controller * - - - -
A10.2.7.3. Bus tie contactor * - - - -
A10.2.7.4. Bus off indication relay * - - - -
A10.2.7.5. Other system components - - - -
A10.2.8. Component location - - - -
A10.2.9. Bench check components - - - -
A10.3. DC POWER SYSTEM
TR: Applicable C-141 TOs, 8 series component TOs
A10.3.1. Operational fundamentals - - - -
A10.3.2. Operational check - - - -
A10.3.3. Troubleshoot - - - -
A10.3.4. Inspect - - - -
A10.3.5. Remove components
C-141 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
179Attachment 10
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A10.3.5.1. Transformer rectifer * - - - -
A10.3.5.2. Battery relay * - - - -
A10.3.5.3. Other system componetns - - - -
A10.3.6. Repair components - - - -
A10.3.7. Install components
A10.3.7.1. Transformer rectifer * - - - -
A10.3.7.2. Battery relay * - - - -
A10.3.7.3. Other system componetns - - - -
A10.3.8. Component location - - - -
A10.3.9. Bench check components - - - -
A10.4. EXTERNAL POWER SYSTEM
TR: Applicable C-141 TOs, 8 series component TOs
A10.4.1. Operational fundamentals - - - -
A10.4.2. Operational check - - - -
A10.4.3. Apply external power - - - -
A10.4.4. Troubleshoot - - - -
A10.4.5. Inspect - - - -
A10.4.6. Remove components
A10.4.6.1. Bus protection panel * - - - -
A10.4.6.2. Other system componetns - - - -
A10.4.7. Repair components - - - -
A10.4.8. Install components
A10.4.8.1. Bus protection panel * - - - -
A10.4.8.2. Other system componetns - - - -
A10.4.9. Component location - - - -
A10.4.10. Bench check components - - - -
A10.5. LIGHTING SYSTEM
TR: Applicable C-141 TOs, 8 series component TOs
A10.5.1. Operational fundamentals - - - -
A10.5.2. Operational check
A10.5.2.1. External - - - -
A10.5.2.2. Internal - - - -
A10.5.2.2.1. Cargo dome lights - - - -
A10.5.2.2.2. Other internal lighting systems - - - -
A10.5.3. Troubleshoot
A10.5.4. Inspect - - - -
A10.5.5. Remove components
C-141 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
180Attachment 10
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A10.5.5.1. External strobe light power supply * - - - -
A10.5.5.2. Autotransformer * - - - -
A10.5.5.3. Other system components - - - -
A10.5.6. Repair components - - - -
A10.5.7. Install components
A10.5.7.1. External strobe light power supply * - - - -
A10.5.7.2. Autotransformer * - - - -
A10.5.7.3. Other system components - - - -
A10.5.8. Repair components - - - -
A10.5.9. Component location - - - -
A10.5.10. Bench check components - - - -
A10.6. LANDING GEAR SYSTEM
TR: Applicable C-141 TOs, 8 series component TOs
A10.6.1. Operational fundamentals - - - -
A10.6.2. Operational check - - - -
A10.6.3. Troubleshoot * - - - -
A10.6.4. Inspect - - - -
A10.6.5. Remove components
A10.6.5.1. Up limit switch * - - - -
A10.6.5.2. Other system components - - - -
A10.6.6. Repair components - - - -
A10.6.7. Install components
A10.6.7.1. Up limit switch * - - - -
A10.6.7.2. Other system components - - - -
A10.6.8. Component location - - - -
A10.6.9. Bench check components - - - -
A10.7. ANTI-SKID SYSTEM
TR: Applicable C-141 TOs, 8 series component TOs
A10.7.1. Operational fundamentals - - - -
A10.7.2. Operational check - - - -
A10.7.3. Troubleshoot - - - -
A10.7.4. Inspect - - - -
A10.7.5. Remove components
A10.7.5.1. Anti-skid box * - - - -
A10.7.5.2. Anti-skid detector * - - - -
A10.7.5.3. Other system components - - - -
A10.7.6. Repair components - - - -
C-141 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
181Attachment 10
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A10.7.7. Install components
A10.7.7.1. Anti-skid box * - - - -
A10.7.7.2. Anti-skid detector * - - - -
A10.7.7.3. Other system components - - - -
A10.7.8. Component location - - - -
A10.7.9. Bench check components - - - -
A10.8. PRIMARY FLIGHT CONTROL SYSTEM
TR: Applicable C-141 TOs, 8 series component TOs
A10.8.1. Operational fundamentals - - - -
A10.8.2. Operational check
A10.8.2.1 Trim systems - - - -
A10.8.2.2. Aileron tab operable - - - -
A10.8.3. Troubleshoot - - - -
A10.8.4. Inspect - - - -
A10.8.5. Remove components - - - -
A10.8.6. Repair components - - - -
A10.8.7. Install components - - - -
A10.8.8. Component location - - - -
A10.8.9. Bench check components - - - -
A10.9. SECONDARY FLIGHT CONTROL SYSTEM
TR: Applicable C-141 TOs, 8 series component TOs
A10.9.1. Operational fundamentals - - - -
A10.9.2. Operational check
A10.9.2.1. Flaps - - - -
A10.9.2.2. Pitch trim - - - -
A10.9.2.3. Test ground spoiler reject take-off (RTOmode) - - - -
A10.9.3. Troubleshoot - - - -
A10.9.4. Inspect - - - -
A10.9.5. Remove components
A10.9.5.1. Flap transmitter - - - -
A10.9.5.2. Other system components - - - -
A10.9.6. Repair components - - - -
A10.9.7. Install components
A10.9.7.1. Flap transmitter - - - -
A10.9.7.2. Other system components - - - -
A10.9.8. Null flap transmitters - - - -
A10.9.9. Component location - - - -
C-141 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
182Attachment 10
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A10.9.10. Bench check components - - - -
A10.10. OVERHEAT/FIRE WARNING SYSTEM
TR: Applicable C-141 TOs, 8 series component TOs
A10.10.1. Operational fundamentals - - - -
A10.10.2. Operational check
A10.10.2.1. Engine - - - -
A10.10.2.2. Auxiliary Power Unit * - - - -
A10.10.3. Troubleshoot - - - -
A10.10.4. Inspect - - - -
A10.10.5. Remove components
A10.10.5.1. Engine fire control box * - - - -
A10.10.5.2. Engine fire loop * - - - -
A10.10.5.3. Other system components - - - -
A10.10.6. Repair components - - - -
A10.10.7. Install components
A10.10.7.1. Engine fire control box * - - - -
A10.10.7.2. Engine fire loop * - - - -
A10.10.7.3. Other system components - - - -
A10.10.8. Component location - - - -
A10.10.9. Bench check components - - - -
A10.11. FIRE EXTINGUISHING SYSTEM
TR: Applicable C-141 TOs, 8 series component TOs
A10.11.1. Operational fundamentals - - - -
A10.11.2. Operational check - - - -
A10.11.3. Troubleshoot - - - -
A10.11.4. Inspect - - - -
A10.11.5. Remove components
A10.11.5.1. Squib * - - - -
A10.11.5.2. Other system components - - - -
A10.11.6. Repair components - - - -
A10.11.7. Install components
A10.11.7.1. Squib * - - - -
A10.11.7.2. Other system components - - - -
A10.11.8. Component location - - - -
A10.11.9. Bench check components - - - -
- - - -
- - - -
C-141 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
183Attachment 10
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A10.12. TAKEOFF WARNING SYSTEM
TR: Applicable C-141 TOs, 8 series component TOs
A10.12.1. Operational fundamentals - - - -
A10.12.2. Operational check * - - - -
A10.12.3. Troubleshoot - - - -
A10.12.4. Inspect - - - -
A10.12.5. Remove components
A10.12.5.1. Touchdown relay #9 - - - -
A10.12.5.2. Other system components - - - -
A10.12.6. Repair components - - - -
A10.12.7. Install components
A10.12.7.1. Touchdown relay #9 - - - -
A10.12.7.2. Other system components - - - -
A10.12.8. Component location - - - -
A10.12.9. Bench check components - - - -
A10.13. MASTER CAUTION/WARNING SYSTEM
TR: Applicable C-141 TOs, 8 series component TOs
A10.13.1. Operational fundamentals - - - -
A10.13.2. Operational check - - - -
A10.13.3. Troubleshoot - - - -
A10.13.4. Inspect - - - -
A10.13.5. Remove components - - - -
A10.13.6. Repair components - - - -
A10.13.7. Install components - - - -
A10.13.8. Component location - - - -
A10.13.9. Bench check components - - - -
A10.14. FUEL WARNING AND CONTROL SYSTEM
TR: Applicable C-141 TOs, 8 series component TOs
A10.14.1. Operational fundamentals - - - -
A10.14.2. Operational check - - - -
A10.14.3. Troubleshoot - - - -
A10.14.4. Inspect - - - -
A10.14.5. Remove components - - - -
A10.14.6. Repair components - - - -
A10.14.7. Install components - - - -
A10.14.8. Component location - - - -
C-141 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
184Attachment 10
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A10.14.9. Bench check components - - - -
A10.15. CARGO DOOR CONTROL AND WARNING SYSTEM
TR: Applicable C-141 TOs, 8 series component TOs
A10.15.1. Operational fundamentals - - - -
A10.15.2. Operational check - - - -
A10.15.3. Troubleshoot - - - -
A10.15.4. Inspect - - - -
A10.15.5. Remove components - - - -
A10.15.6. Repair components - - - -
A10.15.7. Install components - - - -
A10.15.8. Component location - - - -
A10.15.9. Bench check components - - - -
A10.16. START AND IGNITION SYSTEM
TR: Applicable C-141 TOs, 8 series component TOs
A10.16.1. Operational fundamentals - - - -
A10.16.2. Operational check - - - -
A10.16.3. Troubleshoot - - - -
A10.16.3.1. Jet engine - - - -
A10.16.3.2. Auxiliary power unit - - - -
A10.16.4. Inspect - - - -
A10.16.5. Remove components - - - -
A10.16.6. Repair components - - - -
A10.16.7. Install components - - - -
A10.16.8. Component location - - - -
A10.16.9. Bench check components - - - -
A10.17. NESA ANTI-ICING SYSTEM
TR: Applicable C-141 TOs, 8 series component TOs
A10.17.1. Operational fundamentals - - - -
A10.17.2. Operational check - - - -
A10.17.3. Troubleshoot - - - -
A10.17.4. Inspect - - - -
A10.17.5. Remove components
A10.17.5.1. Transformer - - - -
A10.17.5.2. Other system components - - - -
A10.17.6. Repair components - - - -
C-141 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
185Attachment 10
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A10.17.7. Install components
A10.17.7.1. Transformer - - - -
A10.17.7.2. Other system components - - - -
A10.17.8. Component location - - - -
A10.17.9. Bench check components - - - -
A10.18. BLEED AIR DISTRIBUTION SYSTEM
TR: Applicable C-141 TOs, 8 series component TOs
A10.18.1. Operational fundamentals - - - -
A10.18.2. Operational check - - - -
A10.18.3. Bleed down check - - - -
A10.18.4. Perform leakage check - - - -
A10.18.5. Troubleshoot - - - -
A10.18.6. Inspect - - - -
A10.18.7. Remove components
A10.18.7.1. Engine bleed air shutoff valve * - - - -
A10.18.7.2. Other system components - - - -
A10.18.8. Repair components - - - -
A10.18.9. Install components
A10.18.9.1. Engine bleed air shutoff valve * - - - -
A10.18.9.2. Other system components - - - -
A10.18.10. Component location - - - -
A10.18.11. Bench check components - - - -
A10.19. AIR CONDITIONING SYSTEM
TR: Applicable C-141 TOs, 8 series component TOs
A10.19.1. Operational fundamentals - - - -
A10.19.2. Subsystem fundamentals
A10.19.2.1. Rain removal system - - - -
A10.19.2.2. Anti-icing system - - - -
A10.19.2.3. Floor heat system - - - -
A10.19.2.4. Equipment cooling system - - - -
A10.19.3. Operational check * - - - -
A10.19.4. Perform leakage checks * - - - -
A10.19.5. Troubleshoot - - - -
A10.19.6. Inspect - - - -
A10.19.7. Remove components
A10.19.7.1. Water separator - - - -
A10.19.7.2. Other system components - - - -
C-141 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
186Attachment 10
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A10.19.8. Repair components - - - -
A10.19.9. Install components
A10.19.9.1. Water separator coalescer - - - -
A10.19.9.2. Other system components - - - -
A10.19.10. Component location - - - -
A10.19.11. Bench check components - - - -
A10.20. PRESSURIZATION SYSTEM
TR: Applicable C-141 TOs, 8 series component TOs
A10.20.1. Operational fundamentals - - - -
A10.20.2. Operational check * - - - -
A10.20.3. Troubleshoot - - - -
A10.20.4. Inspect - - - -
A10.20.5. Remove components * - - - -
A10.20.6. Repair components - - - -
A10.20.7. Install components * - - - -
A10.20.8. Component location - - - -
A10.20.9. Bench check components - - - -
A10.21. LIQUID OXYGEN SYSTEM
TR: AFOSH standards; TOs 15X1-1, 42B5-1-2, 42E1-1-1, Applicable C-141 Tos
A10.21.1. Operational fundamentals - - - -
A10.21.2. Operational check * - - - -
A10.21.3. Troubleshoot - - - -
A10.21.4. Inspect * - - - -
A10.21.5. Purge system * - - - -
A10.21.6. Remove components
A10.21.6.1. Oxygen regulator - - - -
A10.21.6.2. Other system components - - - -
A10.21.7. Repair components - - - -
A10.21.8. Install components
A10.21.8.1. Oxygen regulator - - - -
A10.21.8.2. Other system components - - - -
A10.21.9. Perform leak check - - - -
A10.21.10. Clean components - - - -
A10.21.11. Procedures for cleaning components - - - -
A10.21.12. Component location - - - -
A10.21.13. Bench check components - - - -
A10.22. LIFE RAFT INFLATION SYSTEM
C-141 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
187Attachment 10
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
TR: Applicable C-141 TOs, 8 series component TOs
A10.22.1. Operational fundamentals - - - -
A10.22.2. Operational check - - - -
A10.22.3. Troubleshoot - - - -
A10.22.4. Inspect - - - -
A10.22.5. Remove components - - - -
A10.22.6. Repair components - - - -
A10.22.7. Install components - - - -
A10.22.8. Component location - - - -
A10.22.9. Bench check components - - - -
F-15 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
188Attachment 11
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
Attachment 11
NOTE 1: In addition to attachment 2, the tasks and knowledge in attachment 5 will be performed by personnel assigned to maintain F-15 aircraft.
NOTE 2: Users are responsible for annotating training references to identify current references pending STS revision.
NOTE 3: Items marked in columns 2a or 2b marked with a (*R) are optional core tasks for ANG and AFRC.
NOTE 4: Address comments and recommended changes through the MAJCOM Functional Managers to the AETC Training Manager, DSN 736-2772.
A11.1. AC POWER SYSTEM
TR: Applicable F-15 TOs, 8 series component TOs
A11.1.1. Operational fundamentals - - - -
A11.1.2. Operational check
A11.1.2.1. Main Generator System * - - - -
A11.1.2.2. Emergency Power System - - - -
A11.1.3. Troubleshoot
A11.1.3.1. Main Generator System - - - -
A11.1.3.2. Emergency Power System - - - -
A11.1.4. Inspect System Components * - - - -
A11.1.5. Remove components
A11.2.5.1. IDG * - - - -
A11.2.5.2. GCU * - - - -
A11.2.5.3. Power contactor * - - - -
A11.2.5.4. IDG Filters - - - -
A11.2.5.5. Relay Panels - - - -
A11.2.5.6. Circuit Breaker Panels - - - -
A11.2.6. Repair components
A11.2.6.1. Generator - - - -
A11.2.6.2. CSD - - - -
A11.2.6.3. Assemble IDG - - - -
A11.2.6.4. Disassemble IDG - - - -
A11.2.6.5. Relay Panels - - - -
A11.2.6.6. Circuit Breaker Panels - - - -
A11.2.7. Install components
A11.2.7.1. IDG * - - - -
A11.2.7.2. GCU * - - - -
A11.2.7.3. Power contactor * - - - -
A11.2.7.4. IDG Filters - - - -
A11.2.7.5. Relay Panels - - - -
A11.2.7.6. Circuit Breaker Panels - - - -
A11.2.8. Component location - - - -
A11.2.9. Bench check
F-15 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
189Attachment 11
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A11.2.9.1. Generator - - - -
A11.2.9.2. CSD - - - -
A11.2.9.3. Relay Panels - - - -
A11.2.9.4. Circuit Breaker Panels - - - -
A11.2.10 Service IDG * - - - -
A11.3. DC POWER SYSTEM
TR: Applicable F-15 TOs, 8 series component TOs
A11.3.1. Operational fundamentals - - - -
A11.3.2. Operational check * - - - -
A11.3.3. Troubleshoot - - - -
A11.3.4. Inspect System Components * - - - -
A11.3.5. Remove components
A11.3.5.1. DC Power Contactor - - - -
A11.3.5.2. Transformer Rectifier - - - -
A11.3.5.3. Circuit Breaker Panels - - - -
A11.3.5.4. Relay Panels - - - -
A11.3.6. Repair components
A11.3.6.1. Circuit Breaker Panels - - - -
A11.3.6.2. Relay Panels - - - -
A11.3.7. Install components
A11.3.7.1. DC Power Contactor - - - -
A11.3.7.2. Transformer Rectifier - - - -
A11.3.7.3. Circuit Breaker Panels - - - -
A11.3.7.4. Relay Panels - - - -
A11.3.8. Bench check components
A11.3.8.1. Circuit Breaker Panels - - - -
A11.3.8.2. Relay Panels - - - -
A11.4. EXTERNAL POWER SYSTEM
TR: Applicable F-15 TOs, 8 series component TOs
A11.4.1. Operational fundamentals - - - -
A11.4.2. Operational check * - - - -
A11.4.3. Apply external power - - - -
A11.4.4. Troubleshoot - - - -
A11.4.5. Inspect System Components * - - - -
A11.4.6. Remove components
A11.4.6.1. External Power Receptacle - - - -
A11.4.6.2. External Power Monitor - - - -
A11.4.6.3. External Power Contactor - - - -
F-15 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
190Attachment 11
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A11.4.7. Install components
A11.4.7.1. External Power Receptacle - - - -
A11.4.7.2. External Power Monitor - - - -
A11.4.7.3. External Power Contactor - - - -
A11.5. LIGHTING SYSTEM
TR: Applicable F-15 TOs, 8 series component TOs
A11.5.1. Operational fundamentals
A11.5.1.1. Exterior - - - -
A11.5.1.2. Interior - - - -
A11.5.1.3. Emergency - - - -
A11.5.2. Operational check
A11.5.2.1. Exterior * - - - -
A11.5.2.2. Interior * - - - -
A11.5.2.3. Emergency * - - - -
A11.5.3. Troubleshoot
A11.5.3.1. Exterior - - - -
A11.5.3.2. Interior - - - -
A11.5.3.3. Emergency - - - -
A11.5.4. Inspect System Components
A11.5.4.1 Exterior * - - - -
A11.5.4.2 Interior * - - - -
A11.5.4.3 Emergency * - - - -
A11.5.5. Remove components *
A11.5.5.1. Position Lights - - - -
A11.5.5.2. Anti-Collision Lights * - - - -
A11.5.5.3. Formation Lights - - - -
A11.5.5.4. Tail Flood Lights - - - -
A11.5.5.5. IFR Flood Light - - - -
A11.5.5.6. IFR Slipway Lights - - - -
A11.5.5.7. Flasher assembly - - - -
A11.5.5.8. Lighting Control Panel * - - - -
A11.5.5.9. Lights Trim Panel * - - - -
A11.5.5.10. Light Assemblies - - - -
A11.5.5.11. Power Supply - - - -
A11.5.5.12. Map Light * - - - -
A11.5.5.13. Flood Lights - - - -
A11.5.6. Repair components
A11.5.6.1. Position Lights - - - -
F-15 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
191Attachment 11
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A11.5.6.2. Anti-Collision Lights - - - -
A11.5.6.3. Taxi Light - - - -
A11.5.6.4. Landing Light - - - -
A11.5.6.5. IFR Flood Light - - - -
A11.5.6.6. Lighting Control Panel - - - -
A11.5.6.7. Lights Trim Panel - - - -
A11.5.6.8. Light Assemblies - - - -
A11.5.6.9. Power Supply - - - -
A11.5.6.10. Map Light - - - -
A11.5.7. Install components
A11.5.7.1. Position Lights - - - -
A11.5.7.2. Anti-Collision Lights * - - - -
A11.5.7.3. Formation Lights - - - -
A11.5.7.4. Tail Flood Lights - - - -
A11.5.7.5. IFR Flood Light - - - -
A11.5.7.6. IFR Slipway Lights - - - -
A11.5.7.7. Flasher assembly - - - -
A11.5.7.8. Lighting Control Panel * - - - -
A11.5.7.9. Lights Trim Panel * - - - -
A11.5.7.10. Light Assemblies - - - -
A11.5.7.11. Power Supply - - - -
A11.5.7.12. Map Light * - - - -
A11.5.7.13. Flood Lights - - - -
A11.5.8. Component location
A11.5.8.1. Exterior - - - -
A11.5.8.2. Interior - - - -
A11.5.8.3. Emergency - - - -
A11.5.9. Bench check components
A11.5.9.1. Position Lights - - - -
A11.5.9.2. Anti-Collision Lights - - - -
A11.5.9.3 Taxi Light - - - -
A11.5.9.4. Landing Light - - - -
A11.5.9.5. IFR Flood Light - - - -
A11.5.9.6. Lighting Control Panel - - - -
A11.5.9.7. Lights Trim Panel - - - -
A11.5.9.8. Light Assemblies - - - -
A11.5.9.9. Power Supply - - - -
A11.5.9.10. Map Light - - - -
F-15 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
192Attachment 11
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A11.6. LANDING GEAR SYSTEM
TR: Applicable F-15 TOs, 6 series component TOs
A11.6.1. Operational fundamentals - - - -
A11.6.2. Operational check * - - - -
A11.6.3. Troubleshoot - - - -
A11.6.4. Inspect System Components * - - - -
A11.6.5. Remove components
A11.6.5.1. Landing Gear Control Handle * - - - -
A11.6.5.2. Control Switches - - - -
A11.6.6. Install components
A11.6.6.1. Landing Gear Control Handle * - - - -
A11.6.6.2. Control Switches - - - -
A11.6.7. Component location - - - -
A11.6.8. Adjust switches - - - -
A11.7. ARRESTING HOOK INDICATION AND WARNING SYSTEM
TR: Applicable F-15 TOs, 8 series component TOs
A11.7.1. Operational fundamentals - - - -
A11.7.2. Operational check - - - -
A11.7.3. Troubleshoot - - - -
A11.7.4. Inspect System Components - - - -
A11.7.5. Remove components
A11.7.5.1. Control switches - - - -
A11.7.5.1. Uplimit switches - - - -
A11.7.5.1. Safety interlock switches - - - -
A11.7.6. Install components
A11.7.6.1. Control switches - - - -
A11.7.6.2. Uplimit switches - - - -
A11.7.6.3. Safety interlock switches - - - -
A11.7.7. Adjust switches - - - -
A11.8. CANOPY INDICATION AND WARNING SYSTEM
TR: Applicable F-15 TOs, 8 series component TOs
A11.8.1. Operational fundamentals - - - -
A11.8.2. Operational check - - - -
A11.8.3. Troubleshoot - - - -
A11.8.4. Inspect System Components - - - -
A11.8.5. Remove components
A11.8.5.1. Canopy position switch - - - -
F-15 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
193Attachment 11
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A11.8.5.2. Canopy lock position switch - - - -
A11.8.5.3. Warning lights - - - -
A11.8.6. Install components
A11.8.6.1. Canopy position switch - - - -
A11.8.6.2. Canopy lock position switch - - - -
A11.8.6.3. Warning lights - - - -
A11.8.7. Adjust switches - - - -
A11.9. ANTI-SKID SYSTEM
TR: Applicable F-15 TOs, 8 series component TOs
A11.9.1. Operational fundamentals - - - -
A11.9.2. Operational check - - - -
A11.9.3. Troubleshoot - - - -
A11.9.4. Inspect System Components * - - - -
A11.9.5. Remove components
A11.9.5.1. Control Box * - - - -
A11.9.5.2. Control Panel - - - -
A11.9.5.3. Brake Pulsar Unit - - - -
A11.9.5.4. Transducer - - - -
A11.9.6. Repair control panel - - - -
A11.9.7. Install components
A11.9.7.1. Control Box * - - - -
A11.9.7.2. Control Panel - - - -
A11.9.7.3. Brake Pulsar Unit - - - -
A11.9.7.4. Transducer - - - -
A11.9.8. Component location - - - -
A11.9.9. Bench check control panel - - - -
A11.10. BRAKE HOLDING SYSTEM
TR: Applicable F-15 TOs, 8 series component TOs
A11.10.1. Operational Fundamentals - - - -
A11.10.2. Operational Check * - - - -
A11.10.3. Troubleshoot - - - -
A11.10.4. Inspect System Components * - - - -
A11.10.5. Remove Brake Hold Switch * - - - -
A11.10.6. Repair Throttle Quadrant - - - -
A11.10.7. Install Brake Hold Switch * - - - -
A11.10.8. Component Location - - - -
A11.10.9. Bench check throttle quadrant - - - -
A11.11. NOSE GEAR STEERING SYSTEM
F-15 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
194Attachment 11
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
TR: Applicable F-15 TOs, 8 series component TOs
A11.11.1. Operational fundamentals - - - -
A11.11.2. Operational check - - - -
A11.11.3. Troubleshoot - - - -
A11.11.4. Inspect System Components - - - -
A11.11.5. Remove range limit switch - - - -
A11.11.6. Install range limit switch - - - -
A11.11.7. Component location - - - -
A11.12. SECONDARY FLIGHT CONTROL SYSTEM
TR: Applicable F-15 TOs, 8 series component TOs
A11.12.1. Operational fundamentals - - - -
A11.12.2. Operational check
A11.12.2.1. Flaps - - - -
A11.12.2.2. Speed brake - - - -
A11.12.3. Troubleshoot
A11.12.3.1. Flaps - - - -
A11.12.3.2. Speed brake - - - -
A11.12.4. Inspect System Components - - - -
A11.12.5. Remove flap airspeed switch - - - -
A11.12.6. Install flap airspeed switch - - - -
A11.12.7. Component location - - - -
A11.13. OVERHEAT/FIRE WARNING SYSTEM
TR: Applicable F-15 TOs, 8 series component TOs
A11.13.1. Operational fundamentals
A11.13.1.1. Engine - - - -
A11.13.1.2. Bleed Air Leak Detection - - - -
A11.13.2. Operational check
A11.13.2.1. Engine * - - - -
A11.13.2.2. Bleed Air Leak Detection * - - - -
A11.13.3. Troubleshoot
A11.13.3.1. Engine - - - -
A11.13.3.2. Bleed Air Leak Detection - - - -
A11.13.4. Inspect System Components * - - - -
A11.13.5. Remove components
A11.13.5.1. Sensing Elements * - - - -
A11.13.5.2. Control Box - - - -
A11.13.5.3. Control Panel - - - -
A11.13.6. Repair components
F-15 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
195Attachment 11
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A11.13.6.1. Control Box - - - -
A11.13.6.2. Control Panel - - - -
A11.13.7. Install components
A11.13.7.1. Sensing Elements * - - - -
A11.13.7.2. Control Box - - - -
A11.13.7.3. Control Panel - - - -
A11.13.8. Bench check components
A11.13.8.1. Control Box - - - -
A11.13.8.2. Control Panel - - - -
A11.14. FIRE EXTINGUISHING SYSTEM
TR: Applicable F-15 TOs, 8 series component TOs
A11.14.1. Operational fundamentals - - - -
A11.14.2. Operational check - - - -
A11.14.3. Troubleshoot - - - -
A11.14.4. Inspect System Components * - - - -
A11.14.5. Remove components
A11.14.5.1. Squib * - - - -
A11.14.5.2. Fire bottle - - - -
A11.14.6. Install components
A11.14.6.1. Squib * - - - -
A11.14.6.2. Fire bottle - - - -
A11.14.7. Component location - - - -
A11.15. MASTER CAUTION/WARNING SYSTEM
TR: Applicable F-15 TOs, 8 series component TOs
A11.15.1. Operational fundamentals - - - -
A11.15.2. Operational check * - - - -
A11.15.3. Troubleshoot - - - -
A11.15.4. Inspect System Components * - - - -
A11.15.5. Remove components
A11.15.5.1. Master Caution Light Assembly - - - -
A11.15.5.2. Warning Lights Assembly - - - -
A11.15.6. Install components
A11.15.6.1. Master Caution Light Assembly - - - -
A11.15.6.2. Warning Lights Assembly - - - -
A11.16. FUEL WARNING AND CONTROL SYSTEM
TR: Applicable F-15 TOs, 8 series component TOs
A11.16.1. Operational fundamentals - - - -
A11.16.2. Operational check - - - -
F-15 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
196Attachment 11
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A11.16.3. Troubleshoot - - - -
A11.16.4. Inspect System Components - - - -
A11.16.5. Remove fuel system ground preflight test panel - - - -
A11.16.6. Repair fuel system ground preflight test panel - - - -
A11.16.7. Install fuel system ground preflight test panel - - - -
A11.16.8. Component location - - - -
A11.16.9. Bench check fuel system ground preflight test panel - - - -
A11.17. START AND IGNITION SYSTEM
TR: Applicable F-17 TOs, 8 series component TOs
A11.17.1. Operational fundamentals - - - -
A11.17.2. Operational check - - - -
A11.17.3. Troubleshoot - - - -
A11.17.4. Inspect wiring - - - -
A11.17.5. Component location - - - -
A11.18. BLEED AIR DISTRIBUTION SYSTEM
TR: Applicable F-15 TOs, 8 series component TOs
A11.18.1. Operational fundamentals - - - -
A11.18.2. Operational check * - - - -
A11.18.3. Troubleshoot - - - -
A11.18.4. Inspect System Components * - - - -
A11.18.5. Remove components
A11.18.5.1. Backup valve * - - - -
A11.18.5.2. Final stage valve * - - - -
A11.18.5.3. Final stage valve solonoid - - - -
A11.18.5.4. Final stage valve filter - - - -
A11.18.5.5. Ejector valve - - - -
A11.18.5.6. Bypass valve - - - -
A11.18.5.7. Sensors - - - -
A11.18.5.8. Ducts - - - -
A11.18.5.9. Tubing - - - -
A11.18.6. Repair bypass valve - - - -
A11.18.7. Install components
A11.18.7.1. Backup valve * - - - -
A11.18.7.2. Final stage valve * - - - -
A11.18.7.3. Final stage valve solonoid - - - -
A11.18.7.4. Final stage valve filter - - - -
A11.18.7.5. Ejector valve - - - -
A11.18.7.6. Bypass valve - - - -
F-15 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
197Attachment 11
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A11.18.7.7. Sensors - - - -
A11.18.7.8. Ducts - - - -
A11.18.7.9. Tubing - - - -
A11.18.8. Perform leakage checks * - - - -
A11.18.9. Component location - - - -
A11.19. AIR CONDITIONING SYSTEM
TR: Applicable F-15 TOs, 8 series component TOs
A11.19.1. Operational fundamentals
A11.19.1.1. High pressure air conditioning system - - - -
A11.19.1.2. Air cycle air conditioning system - - - -
A11.19.1.3. Cabin temperature control - - - -
A11.19.1.4. Avionics temperature control - - - -
A11.19.1.5. Low pressure air conditioning system - - - -
A11.19.2. Subsystem Fundamentals
A11.19.2.1. Anti-G suit system - - - -
A11.19.2.2. Defogging system - - - -
A11.19.3. Operational check
A11.19.3.1. Air conditioning systems * - - - -
A11.19.3.2. Cabin Temperature Control - - - -
A11.19.3.3. Avionics Temperature Control - - - -
A11.19.3.4. Anti-G suit system - - - -
A11.19.3.5. Defogging system - - - -
A11.19.4. Troubleshoot
A11.19.4.1. Air conditioning systems * - - - -
A11.19.4.2. Cabin Temperature Control - - - -
A11.19.4.3. Avionics Temperature Control - - - -
A11.19.4.4. Anti-G suit system - - - -
A11.19.4.5. Defogging system - - - -
A11.19.5. Inspect system components * - - - -
A11.19.6. Remove components
A11.19.6.1. Condenser/Liquid Coolant Heat Exchanger - - - -
A11.19.6.2. High pressure water separator modulating valve - - - -
A11.19.6.3. Regenerative heat exchanger - - - -
A11.19.6.4. Regenerative heat exchanger modulating valve - - - -
A11.19.6.5. Reheater heat exchanger - - - -
A11.19.6.6. Primary heat exchanger - - - -
A11.19.6.7. Secondary heat exchanger - - - -
A11.19.6.8. Secondary heat exchanger ejector valve - - - -
F-15 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
198Attachment 11
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A11.19.6.9. Secondary heat exchanger ejector - - - -
A11.19.6.10. Fuel pressurization heat exchanger - - - -
A11.19.6.11. Turbine/Compressor - - - -
A11.19.6.12. Turbine compressor bypass valve - - - -
A11.19.6.13. Turbine compressor modulating bypass valve - - - -
A11.19.6.14. Turbine compressor modulating shutoff valve * - - - -
A11.19.6.15. Water extractor/separator - - - -
A11.19.6.16. Anti fog heat exchanger - - - -
A11.19.6.17. Anti fog modulating valve - - - -
A11.19.6.18. Anti ice valve - - - -
A11.19.6.19. Check valve - - - -
A11.19.6.20. Cabin air circuit controller - - - -
A11.19.6.21. Cabin hot air valve - - - -
A11.19.6.22. Cabin inlet modulating/shutoff valve - - - -
A11.19.6.23. Cabin ram air valve - - - -
A11.19.6.24. Cabin ram air valve limit switch - - - -
A11.19.6.25. Cabin water separator - - - -
A11.19.6.26. Air conditioning control panel - - - -
A11.19.6.27. Avionics air circuit controller - - - -
A11.19.6.28. Avionics equipment hot air valve - - - -
A11.19.6.29. Avionics cold air modulating valve - - - -
A11.19.6.30. Avionics cooling monitor unit - - - -
A11.19.6.31. Avionics flow control modulating valve - - - -
A11.19.6.32. Displays cooling differential pressure switch - - - -
A11.19.6.33. ICMS cooling control valve - - - -
A11.19.6.34. Sensors - - - -
A11.19.6.35. Ducting - - - -
A11.19.6.36. Anti-G valve - - - -
A11.19.7. Repair air conditioning control panel - - - -
A11.19.8. Install components
A11.19.8.1. Condenser/Liquid Coolant Heat Exchanger - - - -
A11.19.8.2. High pressure water separator modulating valve - - - -
A11.19.8.3. Regenerative heat exchanger - - - -
A11.19.8.4. Regenerative heat exchanger modulating valve - - - -
A11.19.8.5. Reheater heat exchanger - - - -
A11.19.8.6. Primary heat exchanger - - - -
A11.19.8.7. Secondary heat exchanger - - - -
A11.19.8.8. Secondary heat exchanger ejector valve - - - -
F-15 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
199Attachment 11
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A11.19.8.9. Secondary heat exchanger ejector - - - -
A11.19.8.10. Fuel pressurization heat exchanger - - - -
A11.19.8.11. Turbine/Compressor - - - -
A11.19.8.12. Turbine compressor bypass valve - - - -
A11.19.8.13. Turbine compressor modulating bypass valve - - - -
A11.19.8.14. Turbine compressor modulating shutoff valve * - - - -
A11.19.8.15. Water extractor/separator - - - -
A11.19.8.16. Anti fog heat exchanger - - - -
A11.19.8.17. Anti fog modulating valve - - - -
A11.19.8.18. Anti ice valve - - - -
A11.19.8.19. Check valve - - - -
A11.19.8.20. Cabin air circuit controller - - - -
A11.19.8.21. Cabin hot air valve - - - -
A11.19.8.22. Cabin inlet modulating/shutoff valve - - - -
A11.19.8.23. Cabin ram air valve - - - -
A11.19.8.24. Cabin ram air valve limit switch - - - -
A11.19.8.25. Cabin water separator - - - -
A11.19.8.26. Air conditioning control panel - - - -
A11.19.8.27. Avionics air circuit controller - - - -
A11.19.8.28. Avionics equipment hot air valve - - - -
A11.19.8.29. Avionics cold air modulating valve - - - -
A11.19.8.30. Avionics cooling monitor unit - - - -
A11.19.8.31. Avionics flow control modulating valve - - - -
A11.19.8.32. Displays cooling differential pressure switch - - - -
A11.19.8.33. ICMS cooling control valve - - - -
A11.19.8.34. Sensors - - - -
A11.19.8.35. Ducting - - - -
A11.19.8.36. Anti-G valve - - - -
A11.19.9. Perform leakage checks * - - - -
A11.19.10. Service turbine - - - -
A11.19.11. Bench check air conditioning control panel - - - -
A11.20. PRESSURIZATION SYSTEM
TR: Applicable F-15 TOs, 8 series component TOs
A11.20.1. Operational fundamentals
A11.20.1.1. Aircraft pressurization system - - - -
A11.20.1.2. Canopy seal pressurization system - - - -
A11.20.2. Operational check
A11.20.2.1. Aircraft Pressurization system * - - - -
F-15 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
200Attachment 11
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A11.20.2.2. Canopy seal pressurization system - - - -
A11.20.3. Troubleshoot
A11.20.3.1. Aircraft pressurization system * - - - -
A11.20.3.2. Canopy seal pressurization system - - - -
A11.20.4. Inspect system components * - - - -
A11.20.5. Remove components
A11.20.5.1. Safety valve - - - -
A11.20.5.2. Cabin pressure controller - - - -
A11.20.5.3. Canopy seal - - - -
A11.20.5.4. Canopy seal pressure regulator - - - -
A11.20.6. Install components
A11.20.6.1. Safety valve - - - -
A11.20.6.2. Cabin pressure controller - - - -
A11.20.6.3. Canopy seal - - - -
A11.20.6.4. Canopy seal pressure regulator - - - -
A11.21. LIQUID COOLANT SYSTEM
TR: Applicable F-15 TOs, 8 series component TOs
A11.21.1. Operational fundamentals - - - -
A11.21.2. Troubleshoot - - - -
A11.21.3. Inspect system components * - - - -
A11.21.4. Remove LCS pump - - - -
A11.21.5. Install LCS pump - - - -
A11.21.6. Component location - - - -
A11.21.7. Service - - - -
A11.22. LIQUID OXYGEN SYSTEM
TR: AFOSH standards; TOs 15X1-1, 42B5-1-2,42E1-1-1, Applicable F-15 TOs, 8 seriescomponent TOs
A11.22.1. Operational fundamentals - - - -
A11.22.2. Operational check * - - - -
A11.22.3. Troubleshoot - - - -
A11.22.4. Inspect system components * - - - -
A11.22.5. Purge
A11.22.5.1. System * - - - -
A11.22.5.2. Converter * - - - -
A11.22.6. Remove components
A11.22.6.1. Converter * - - - -
A11.22.6.2. Oxygen gauge * - - - -
A11.22.6.3. Oxygen regulator * - - - -
F-15 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
201Attachment 11
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A11.22.7. Repair Converter - - - -
A11.22.8. Install components
A11.22.8.1. Converter * - - - -
A11.22.8.2. Oxygen gauge * - - - -
A11.22.8.3. Oxygen regulator * - - - -
A11.22.9. Perform leak check * - - - -
A11.22.10. Clean components and tools * - - - -
A11.22.11. Drain Converter - - - -
A11.22.12.. Service Converter - - - -
A11.23. Molecular Seive Oxygen Generating System
TR: Applicable F-15 TOs, 8 series component TOs
A11.23.1. Operational fundamentals - - - -
A11.23.2. Operational check * - - - -
A11.23.3. Troubleshoot - - - -
A11.23.4. Inspect system components * - - - -
A11.23.5. Remove components
A11.23.5.1. Concentrator * - - - -
A11.23.5.2. Oxygen Regulator * - - - -
A11.23.5.3. Tubing - - - -
A11.23.5.4. Bit Panel - - - -
A11.23.6. Install components
A11.23.6.1. Concentrator * - - - -
A11.23.6.2. Oxygen Regulator * - - - -
A11.23.6.3. Tubing - - - -
A11.23.6.4. Bit Panel - - - -
F-16 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
202Attachment 12
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
ATTACHMENT 12
NOTE 1: In addition to attachment 2, the tasks and knowledge in attachment 4 will be performed by assigned to maintain F-16 aircraft
NOTE 2: Users are responsible for annotating training references to identify current references pending STS revision.
NOTE 3: Items marked in columns 2a or 2b marked with a (*R) are optional core tasks for ANG and AFRC.
NOTE 4: Address comments and recommended changes through the MAJCOM Functional Managers to the AETC Training Manager, DSN 736-2772.
A12.1. METERS AND TESTERS
TR: Applicable 33 series TOs
A12.1.1. Use ECS tester - - - -
A12.1.2. Use sonic leak detector - - - -
A12.1.3. Use cockpit cabin pressure leakage tester - - - -
A12.1.4. Use anti-skid tester - - - -
A12.1.5. Use bonding meter - - - -
A12.1.6. Use USM-128 - - - -
A12.1.7. Use EPU maintenance test set - - - -
A12.1.8. Use Enhanced Diagnostics Unit (EDNA) - - - -
A12.1.9. Use Oxygen Regulator Tester - - - -
A12.2. AIR CONDITIONING SYSTEM, COMPRESSION
TR: Applicable F-16 TOs, 8 series and 15 series component TOs
A12.2.1. Operational fundamentals - - - -
A12.2.2. Operational check - - - -
A12.2.3. Troubleshoot - - - -
A12.2.4. Inspect - - - -
A12.2.5. Remove components
A12.2.5.1. Low stage valve - - - -
A12.2.5.2. High stage valve - - - -
A12.2.5.3. Bleed air check valve - - - -
A12.2.5.4. VAPR - - - -
A12.2.5.5. Environmental Control Sensor - - - -
A12.2.5.6. Servo Air Filter Element - - - -
A12.2.5.7. Other system components - - - -
A12.2.6. Repair Components - - - -
A12.2.7. Install components
A12.2.7.1. Low stage valve - - - -
A12.2.7.2. High stage valve - - - -
A12.2.7.3. Bleed air check valve - - - -
A12.2.7.4. VAPR - - - -
A12.2.7.5. Environmental Control Sensor - - - -
F-16 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
203Attachment 12
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A12.2.7.6. Servo air filter element - - - -
A12.2.7.7. Other system components - - - -
A12.2.8. Perform Leak Checks - - - -
A12.2.9. Bench check components - - - -
A12.3. AIR CONDITIONING SYSTEM, DISTRIBUTION
TR: Applicable F-16 Tos
A12.3.1. Operational fundamentals - - - -
A12.3.2. Operational check - - - -
A12.3.3. Troubleshoot - - - -
A12.3.4. Inspect - - - -
A12.3.5 Remove Components
A12.3.5.1. Electronic Equipment sensors controller - - - -
A12.3.5.2. Priority Valve - - - -
A12.3.5.3. Electronic cooling mod valve - - - -
A12.3.5.4. Cold air shutoff drive valve - - - -
A12.3.5.5. Radar cooling shutoff valve - - - -
A12.3.5.6. Other system components - - - -
A12.3.6. Install Components
A12.3.6.1. Electronic Equipment sensors controller - - - -
A12.3.6.2. Priority Valve - - - -
A12.3.6.3. Electronic cooling mod valve - - - -
A12.3.6.4. Cold air shutoff drive valve - - - -
A12.3.6.5. Radar cooling shutoff valve - - - -
A12.3.6.6. Other system components - - - -
A12.3.7. Perform leakage checks - - - -
A12.3.8. Component Location - - - -
A12.4. AIR CONDITIONING SYSTEM, PRESSURIZATION
TR: Applicable F-16 TOs, 15 series component Tos
A12.4.1. Operational fundamentals
A12.4.1.1. Aircraft Pressurization System - - - -
A12.4.1.2. Canopy Seal Pressurization System - - - -
A12.4.1.3. Anti-G Suit System - - - -
A12.4.2. Operational Check
A12.4.2.1. Pressurization system - - - -
A12.4.2.2. Seal System - - - -
A12.4.2.3. Anti-G - - - -
A12.4.2.4. Other system components - - - -
F-16 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
204Attachment 12
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A12.4.3. Troubleshoot - - - -
A12.4.4. Inspect - - - -
A12.4.5. Remove components
A12.4.5.1. Canopy Seal Filter Element - - - -
A12.4.5.2. Canopy seal regulator - - - -
A12.4.5.3. Anti-G valve - - - -
A12.4.5.4. Cabin pressure regulator - - - -
A12.4.5.5. Cabin pressure relief and dump valve - - - -
A12.4.5.6. Other system components - - - -
A12.4.6. Repair Components - - - -
A12.4.7. Install components
A12.4.7.1. Canopy Seal Filter Element - - - -
A12.4.7.2. Canopy seal regulator - - - -
A12.4.7.3. Anti-G valve - - - -
A12.4.7.4. Cabin pressure regulator - - - -
A12.4.7.5. Cabin pressure relief and dump valve - - - -
A12.4.7.6. Other system components - - - -
A12.4.8. Perform Leakage checks - - - -
A12.4.9. Component location - - - -
A12.4.10. Bench check components - - - -
A12.5. AIR CONDITIONING SYSTEM, COOLING
TR: Applicable F-16 TOs
A12.5.1. Operational fundamentals - - - -
A12.5.2. Operational check - - - -
A12.5.3. Troubleshoot - - - -
A12.5.4. Inspect - - - -
A12.5.5. Remove components
A12.5.5.1. Water Separator Coalescer - - - -
A12.5.5.2. Cooling Air Turbine compressor - - - -
A12.5.5.3. Regenerative heat exchanger - - - -
A12.5.5.4. Primary and secondary heat exchanger - - - -
A12.5.5.5. Water separator anti-ice modulating valve - - - -
A12.5.5.6. Hot air sensor controller - - - -
A12.5.5.7. Hot air control valve - - - -
A12.5.5.8. Other Components - - - -
A12.5.6. Repair components - - - -
A12.5.7. Install components
A12.5.7.1. Water Separator Coalescer - - - -
F-16 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
205Attachment 12
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A12.5.7.2. Cooling Air Turbine compressor - - - -
A12.5.7.3. Regenerative heat exchanger - - - -
A12.5.7.4. Primary and secondary heat exchanger - - - -
A12.5.7.5. Water separator anti-ice modulating valve - - - -
A12.5.7.6. Hot air sensor controller - - - -
A12.5.7.7. Hot air control valve - - - -
A12.5.7.8. Other Components - - - -
A12.5.8. Perform Leakage checks - - - -
A12.5.9. Component location - - - -
A12.6. AIR CONDITIONING SYSTEM, TEMPERATURECONTROL
TR: Applicable F-16 TOs, 8 series component TOs
A12.6.1. Operational fundamentals - - - -
A12.6.2. Operational check - - - -
A12.6.3. Troubleshoot - - - -
A12.6.4. Inspect - - - -
A12.6.5. Remove components
A12.6.5.1. Cabin temperature sensor/controller - - - -
A12.6.5.2. Cabin temperature control valve - - - -
A12.6.5.3. Air conditioning control panel - - - -
A12.6.5.4. Cabin temperature sensor fan - - - -
A12.6.5.5. Cabin temperature sensor - - - -
A12.6.5.6. Defog switches - - - -
A12.6.5.7. Other system components - - - -
A12.6.6. Repair components - - - -
A12.6.7. Install components
A12.6.7.1. Cabin temperature sensor/controller - - - -
A12.6.7.2. Cabin temperature control valve - - - -
A12.6.7.3. Air conditioning control panel - - - -
A12.6.7.4. Cabin temperature sensor fan - - - -
A12.6.7.5. Cabin temperature sensor - - - -
A12.6.7.6. Defog switches - - - -
A12.6.7.7 Other system components - - - -
A12.6.8. Component location - - - -
A12.6.9. Bench check components - - - -
A12.7. AC ELECTRICAL POWER SYSTEM
TR: Applicable F-16 TOs, 8 series and 16 series component TOs
A12.7.1. Operational fundamentals - - - -
F-16 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
206Attachment 12
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A12.7.2. Operational check - - - -
A12.7.3. Troubleshoot - - - -
A12.7.4. Inspect - - - -
A12.7.5. Remove components
A12.7.5.1. CSD/GEN - - - -
A12.7.5.2. Main GCU - - - -
A12.7.5.3. Standby Generator - - - -
A12.7.5.4. Standby GCU - - - -
A12.7.5.5. Standby generator converter - - - -
A12.7.5.6. Overcurrent protection panels - - - -
A12.7.5.7. Main bus power contactors - - - -
A12.7.5.8. Other system components - - - -
A12.7.6. Repair components - - - -
A12.7.7. Install components
A12.7.7.1. CSD/GEN - - - -
A12.7.7.2. Main GCU - - - -
A12.7.7.3. Standby Generator - - - -
A12.7.7.4. Standby GCU - - - -
A12.7.7.5. Standby generator converter - - - -
A12.7.7.6. Overcurrent protection panels - - - -
A12.7.7.7. Main bus power contactors - - - -
A12.7.7.8. Other system components - - - -
A12.7.8. Component location - - - -
A12.7.9. Bench check components - - - -
A12.8. DC ELECTRICAL POWER SYSTEM
TR: Applicable F-16 TOs, 8 series component TOs
A12.8.1. Operational fundamentals - - - -
A12.8.2. Operational check
A12.8.2.1. DC Power Generation - - - -
A12.8.2.2. Other systems - - - -
A12.8.3. Troubleshoot - - - -
A12.8.4. Inspect - - - -
A12.8.5. Remove components
A12.8.5.1. DC Converters - - - -
A12.8.5.2. Battery control relay assembly - - - -
A12.8.5.3. Aircraft battery - - - -
A12.8.6 Repair comoponents - - - -
A12.8.7. Install components
F-16 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
207Attachment 12
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A12.8.7.1. DC Converters - - - -
A12.8.7.2. Battery control relay assembly - - - -
A12.8.7.3. Aircraft battery - - - -
A12.8.8. Component Location - - - -
A12.8.9. Bench check components - - - -
A12.9. EXTERNAL ELECTRICAL POWER SYSTEM
TR: Applicable F-16 TOs, 8 series component TOs
A12.9.1. Operational fundamentals - - - -
A12.9.2. Operational check - - - -
A12.9.3. Troubleshoot - - - -
A12.9.4. Inspect - - - -
A12.9.5. Remove components
A12.9.5.1. External power receptacle - - - -
A12.9.5.2. External power monitor - - - -
A12.9.6. Repair components - - - -
A12.9.7. Install components
A12.9.7.1. External power receptacle - - - -
A12.9.7.2. External power monitor - - - -
A12.9.8. Apply external Power - - - -
A12.9.9. Remove external power - - - -
A12.9.10. Lubricate external power receptacle - - - -
A12.9.11. Component location - - - -
A12.9.12. Bench check components - - - -
A12.10. ELECTRICAL POWER SYSTEM, DISTRIBUTION
TR: Applicable F-16 TOs
A12.10.1. Operational fundamentals - - - -
A12.10.2. Operational check - - - -
A12.10.3. Troubleshoot - - - -
A12.10.4. Inspect - - - -
A12.10.5. Remove components - - - -
A12.10.6. Install components - - - -
A12.10.7. Component location - - - -
A12.11. OVERHEAT/FIRE WARNING SYSTEM
TR: Applicable F-16 Tos and 8 series component TOs
A12.11.1. Operational fundamentals - - - -
A12.11.2. Operational check - - - -
A12.11.3. Troubleshoot - - - -
F-16 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
208Attachment 12
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A12.11.4. Inspect - - - -
A12.11.5. Remove components
A12.11.5.1. Fire detection set control unit - - - -
A12.11.5.2. Overheat detection set control unit - - - -
A12.11.5.3. Fire and overheat sensing elements - - - -
A12.11.6. Repair components - - - -
A12.11.7. Install components
A12.11.7.1. Fire detection set control unit - - - -
A12.11.7.2. Overheat detection set control unit - - - -
A12.11.7.3. Fire and overheat sensing elements - - - -
A12.12. FUEL INERTING SYSTEM
TR: Applicable F-16 TOs, 8 series component Tos, and TO 6J14-4-9-2
A12.12.1. Operational fundamentals - - - -
A12.12.2. Operational check - - - -
A12.12.3. Troubleshoot - - - -
A12.12.4. Inspect - - - -
A12.12.5. Remove components - - - -
A12.12.6. Repair components - - - -
A12.12.7. Install components - - - -
A12.12.8. Service Halon Bottle
A12.12.8.1. Service with nitrogen - - - -
A12.12.8.2. Service with halon - - - -
A12.12.9. Component location - - - -
A12.12.10. Bench check components - - - -
A12.13. FLIGHT CONTROL SYSTEMS, SPEEDBRAKES
TR: Applicable F-16 TOs
A12.13.1. Operational fundamentals - - - -
A12.13.2. Operational check - - - -
A12.13.3. Troubleshoot - - - -
A12.13.4. Inspect - - - -
A12.13.5. Remove components
A12.13.5.1. 43-degree switch - - - -
A12.13.5.2. Speed brake close position switch - - - -
A12.13.6. Install components
A12.13.6.1. 43-degree switch - - - -
A12.13.6.2. Speed brake close position switch - - - -
A12.13.7. Component location - - - -
F-16 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
209Attachment 12
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A12.14. FUEL SYSTEM, DISTRIBUTION
TR: Applicable F-16 Tos, 8 series component Tos
A12.14.1. Operational fundamentals
A12.14.1.1. Aerial Refuel System - - - -
A12.14.1.2. Engine Fuel Shutoff - - - -
A12.14.1.3. Fuel Distribution - - - -
A12.14.2. Operational check
A12.14.2.1. Fuel shutoff valve - - - -
A12.14.2.2. Other system components - - - -
A12.14.3. Troubleshoot - - - -
A12.14.4. Inspect - - - -
A12.14.5. Remove components - - - -
A12.14.6. Repair components - - - -
A12.14.7. Install components - - - -
A12.14.8. Component location - - - -
A12.14.9. Bench check components - - - -
A12.15. LANDING GEAR EXTENTION AND RETRACTION
TR: Applicable F-16 Tos, 16 series component Tos
A12.15.1. Operational fundamentals - - - -
A12.15.2. Operational check - - - -
A12.15.3. Troubleshoot - - - -
A12.15.4. Inspect - - - -
A12.15.5. Remove components
A12.15.5.1. Landing gear control handle - - - -
A12.15.5.2. Landing gear control panel - - - -
A12.15.5.3. Other system components - - - -
A12.15.6. Repair components - - - -
A12.15.7. Install components
A12.15.7.1. Landing gear control handle - - - -
A12.15.7.2. Landing gear control panel - - - -
A12.15.7.3. Other system components - - - -
A12.15.8. Component location - - - -
A12.15.9. Bench check components - - - -
A12.16. LANDING GEAR WHEELS AND BRAKES
TR: Applicable F-16 TOs, 8 series component TOs
A12.16.1. Operational fundamentals - - - -
A12.16.2. Operational check - - - -
F-16 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
210Attachment 12
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A12.16.3. Troubleshoot - - - -
A12.16.4. Inspect - - - -
A12.16.5. Remove components
A12.16.5.1. Brake control/anti-skid assembly - - - -
A12.16.5.2. Main weight on wheel switch - - - -
A12.16.5.3. Wheel speed sensor - - - -
A12.16.5.4. Other system components - - - -
A12.16.6. Install components
A12.16.6.1. Brake control/anti-skid assembly - - - -
A12.16.6.2. Main weight on wheel switch - - - -
A12.16.6.3. Wheel speed sensor - - - -
A12.16.6.4. Other system components - - - -
A12.16.7. Component location - - - -
A12.17. NOSE WHEEL STEERING SYSTEM
TR: Applicable F-16 TOs
A12.17.1. Operational fundamentals - - - -
A12.17.2. Operational check - - - -
A12.17.3. Troubleshoot - - - -
A12.17.4. Inspect - - - -
A12.17.5. Remove components
A12.17.5.1. Feedback potentiometer - - - -
A12.17.5.2. Command potentiometer - - - -
A12.17.5.3. Steering control box - - - -
A12.17.5.4. Nose landing gear weight-on-wheel switch - - - -
A12.17.5.5. Other system components - - - -
A12.17.6. Install components
A12.17.6.1. Feedback potentiometer - - - -
A12.17.6.2. Command potentiometer - - - -
A12.17.6.3. Steering control box - - - -
A12.17.6.4. Nose landing gear weight-on-wheel switch - - - -
A12.17.6.5. Other system components - - - -
A12.17.7. Adjust feedback potentiometer - - - -
A12.17.8. Component location - - - -
A12.18. LANDING GEAR POSITION AND WARNING
TR: Applicable F-16 Tos, 8 series component TOs
A12.18.1. Operational fundamentals - - - -
A12.18.2. Operational check - - - -
A12.18.3. Troubleshoot - - - -
F-16 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
211Attachment 12
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A12.18.4. Inspect - - - -
A12.18.5. Remove components
A12.18.5.1. MLG door actuator - - - -
A12.18.5.2. NLG door actuator - - - -
A12.18.5.3. MLG downlock switch - - - -
A12.18.5.4. NLG downlock switch - - - -
A12.18.5.5. MLG uplock switch - - - -
A12.18.6. Repair components - - - -
A12.18.7. Install components
A12.18.7.1. MLG door actuator - - - -
A12.18.7.2. NLG door actuator - - - -
A12.18.7.3. MLG downlock switch - - - -
A12.18.7.4. NLG downlock switch - - - -
A12.18.7.5. MLG uplock switch - - - -
A12.18.8. Component location - - - -
A12.18.9. Bench check components - - - -
A12.19. ARRESTING HOOK
TR: Applicable F-16 TOs
A12.19.1. Operational fundamentals - - - -
A12.19.2. Operational check - - - -
A12.19.3. Troubleshoot - - - -
A12.19.4. Inspect - - - -
A12.19.5. Remove components
A12.19.5.1. Uplock switch - - - -
A12.19.6. Install components
A12.19.6.1. Uplock switch - - - -
A12.19.7. Component location - - - -
A12.20. INTERNAL LIGHTING SYSTEM
TR: Applicable F-16 Tos, 8 series and 16 series TOs
A12.20.1. Operational fundamentals
A12.20.1.1. Internal cockpit lighting system - - - -
A12.20.1.2. Master caution/warning system - - - -
A12.20.2. Operational check - - - -
A12.20.3. Troubleshoot - - - -
A12.20.4. Inspect - - - -
A12.20.5. Remove components - - - -
A12.20.6. Repair components - - - -
A12.20.7. Install components - - - -
F-16 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
212Attachment 12
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A12.20.8. Component location - - - -
A12.20.9. Bench check components - - - -
A12.21. EXTERNAL LIGHTING SYSTEM
TR: Applicable F-16 TOs, 8 series component TOs
A12.21.1. Operational fundamentals - - - -
A12.21.2. Operational check - - - -
A12.21.3. Troubleshoot - - - -
A12.21.4. Inspect - - - -
A12.21.5. Remove components - - - -
A12.21.6. Repair components - - - -
A12.21.7. Install components - - - -
A12.21.8. Component location - - - -
A12.21.9. Bench check components - - - -
A12.22. OXYGEN SYSTEM
TR: Applicable F-16 TOs, AFOSH Standards, and TO 15X-1-1
A12.22.1. Operational fundamentals - - - -
A12.22.2. Operational check
A12.22.2.1. 60/180 day oxygen regulator - - - -
A12.22.2.2. Oxygen system tubing purge - - - -
A12.22.2.3. Hot purge liquid oxygen converter - - - -
A12.22.2.4. Other system operational checks - - - -
A12.22.3. Troubleshoot - - - -
A12.22.4. Inspect - - - -
A12.22.5. Remove components
A12.22.5.1. Converter - - - -
A12.22.5.2. Oxygen regulator - - - -
A12.22.5.3. Other system components - - - -
A12.22.6. Install components
A12.22.6.1. Converter - - - -
A12.22.6.2. Oxygen regulator - - - -
A12.22.6.3. Other system components - - - -
A12.22.7. Perform leak checks - - - -
A12.22.8. Clean components - - - -
A12.22.9. Component location - - - -
A12.22.10. Bench check components - - - -
A12.23. ELECTRICAL PANELS AND MULTIPURPOSECOMPONENTS
TR: Applicable F-16 TOs, 16 series component TOs
F-16 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
213Attachment 12
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A12.23.1. Operational check - - - -
A12.23.2. Troubleshoot - - - -
A12.23.3. Inspect - - - -
A12.23.4. Remove components - - - -
A12.23.5. Repair components - - - -
A12.23.6. Install components - - - -
A12.23.7. Component location - - - -
A12.23.8 Bench check components - - - -
A12.24. EMERGENCY POWER SYSTEM
TR: Applicable F-16 TOs, 8 series component TOs
A12.24.1. Operational fundamentals - - - -
A12.24.2. Operational check
A12.24.2.1. EPU auto manual start signal checkout - - - -
A12.24.2.2. EPU mono-propellant mode checkout - - - -
A12.24.2.3. EPU bleed air mode checkout - - - -
A12.24.2.4. Other systems - - - -
A12.24.3. Troubleshoot - - - -
A12.24.4. Inspect - - - -
A12.24.5. Remove components
A12.24.5.1. EPU speed controller - - - -
A12.24.5.2. EPU bleed air shutoff valve - - - -
A12.24.5.3. Other system components - - - -
A12.24.6. Repair components - - - -
A12.24.7. Install components
A12.24.7.1. EPU speed controller - - - -
A12.24.7.2. EPU bleed air shutoff valve - - - -
A12.24.7.3. Other system components - - - -
A12.24.8. EPU safety - - - -
A12.24.9. Hydrazine safety - - - -
A12.24.10. Component location - - - -
A12.24.11. Bench check components - - - -
A12.25. ENGINE STARTING SYSTEM
TR: Applicable F-16 TOs, 6 & 8 series component TOs
A12.25.1. Operational fundamentals - - - -
A12.25.2. Operational check
A12.25.2.1. Jet fuel starter weight-on-wheels - - - -
A12.25.2.2. Other system operational checks - - - -
F-16 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
214Attachment 12
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A12.25.3. Troubleshoot - - - -
A12.25.4. Inspect - - - -
A12.25.5. Remove components - - - -
A12.25.6. Repair components - - - -
A12.25.7. Install components - - - -
A12.25.8. Component location - - - -
A12.25.9. Bench check components - - - -
A12.26. CANOPY SYSTEM
TR: Applicable F-16 TO
A12.26.1. Operational fundamentals - - - -
A12.26.2. Operational check - - - -
A12.26.3. Troubleshoot - - - -
A12.26.4. Inspect - - - -
A12.26.5. Remove components - - - -
A12.26.7. Install components - - - -
A12.26.8. Component location - - - -
KC-10 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
215Attachment 13
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
ATTACHMENT 13
NOTE 1: In addition to attachment 2, the tasks and knowledge in attachment 11 will be performed by personnel assigned to maintain KC-10 aircraft.
NOTE 2: Users are responsible for annotating training references to identify current references pending STS revision.
NOTE 3: Items marked in columns 2a or 2b marked with a (*R) are optional core tasks for ANG and AFRC.
NOTE 4: Address comments and recommended changes through Unit Training Managers to the MAJCOM Maintenance Training Manager @ HQAMC/LGMMT, 402 Scott Drive Unit 2A2, Scott AFB, IL 62225-5308; or call DSN 576-4787. MAJCOM Training and Functional Managers forward inputs tothe AETC Training Manager, DSN 736-2772.
A13.1. AC POWER SYSTEM
A13.1.1. Operational fundamentals
A13.1.1.1. 400 Hertz AC generator system operational fundamentals
TR: TO 1C-10(K)A-2-24-00
- - - -
A13.1.1.2. Emergency AC power operational fundamentals
TR: TO 1C-10(K)A-2-24-20
- - - -
A13.1.2. Operational check
A13.1.2.1. AC generator system operational checkout
TR: TO 1C-10(K)A-2-24-20
* - - - -
A13.1.2.2. Emergency AC power operational checkout
TR: TO 1C-10(K)A-2-24-24
* - - - -
A13.1.3. Troubleshoot - - - -
A13.1.4. Inspect
A13.1.4.1. Generator control unit/bus control unit
TR: TO 1C-10(K)A-2-24-21
* - - - -
A13.1.4.2. AC power relays (generator, bus tie, aux. power, ground service and ext. power)
TR: TO 1C-10(K)A-2-24-21
* - - - -
A13.1.4.3. Remote control circuit breakers
TR: TO 1C-10(K)A-2-24-50
- - - -
A13.1.4.4. 1200 VA static inverter
TR: TO 1C-10(K)A-2-24-24
- - - -
A13.1.4.5. CSD load controller - - - -
A13.1.5. Remove components
A13.1.5.1. Generator control unit/bus control unit
TR: TO 1C-10(K)A-2-24-21
- - - -
A13.1.5.2. AC power relays (generator, bus tie, aux power, ground service and ext power)
TR: TO 1C-10(K)A-2-24-21
- - - -
A13.1.5.3. Remote control circuit breakers
TR: TO 1C-10(K)A-2-24-50
- - - -
- - - -
KC-10 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
216Attachment 13
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A13.1.5.4. 1200 VA static inverter
TR: TO 1C-10(K)A-2-24-24
- - - -
A13.1.5.5. CSD load controller - - - -
A13.1.6. Repair components - - - -
A13.1.7. Install components
A13.1.7.1. Generator control unit/bus control unit
TR: TO 1C-10(K)A-2-24-21
- - - -
A13.1.7.2. AC power relays (generator, bus tie, aux power, ground service and ext power)
TR: TO 1C-10(K)A-2-24-21
- - - -
A13.1.7.3. Remote control circuit breakers
TR: TO 1C-10(K)A-2-24-50
- - - -
A13.1.7.4. 1200 VA static inverter
TR: TO 1C-10(K)A-2-24-24
- - - -
A13.1.7.5. CSD load controller - - - -
A13.1.8. Bench check
A13.1.8.1. Adjust Constant Speed Drive (CSD) basic speed
TR: TO 1C-10(K)A-2-24-10
- - - -
A13.2. DC POWER SYSTEM
A13.2.1. Operational fundamentals
A13.2.1.1. DC power cross tie operational fundamentals
TR: TO 1C-10(K)A-2-24-30
- - - -
A13.2.2. Operational check
A13.2.2.1. Aircraft battery charging system operational checkout
TR: TO 1C-10(K)A-2-24-30
* - - - -
A13.2.2.2. DC power cross tie operational checkout
TR: TO 1C-10(K)A-2-24-30
- - - -
A13.2.3. Troubleshoot
A13.2.3.1. Aircraft battery charging system troubleshooting
TR: TO 1C-10(K)A-2-24-TAFI
- - - -
A13.2.4. Inspect
A13.2.4.1. Transformer rectifier unit
TR: TO 1C-10(K)A-2-24-31
* - - - -
A13.2.4.2. Charger
TR: TO 1C-10(K)A-2-24
- - - -
A13.2.5. Remove components
A13.2.5.1. Transformer rectifier unit
TR: TO 1C-10(K)A-2-24-31
- - - -
KC-10 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
217Attachment 13
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A13.2.5.2. Charger
TR: TO 1C-10(K)A-2-24
- - - -
A13.2.6. Repair components
A13.2.7. Install components - - - -
A13.2.7.1. Transformer rectifier unit
TR: TO 1C-10(K)A-2-24-31
- - - -
A13.2.7.2. Charger
TR: TO 1C-10(K)A-2-24
- - - -
A13.2.7.3. Aircraft batteries
TR: TO 1C-10(K)A-2-24
- - - -
A13.2.8. Bench check - - - -
A13.3. EXTERNAL POWER SYSTEM
A13.3.1. Operational fundamentals - - - -
A13.3.2. Operational check * - - - -
A13.3.3. Troubleshoot - - - -
A13.3.4. Inspect System Components * - - - -
A13.3.5. Remove components - - - -
A13.3.6. Repair components - - - -
A13.3.7. Install components - - - -
A13.3.8. Bench check - - - -
A13.4. LIGHTING SYSTEM
A13.4.1. Operational fundamentals - - - -
A13.4.1.1. Emergency lighting operational fundamentals
TR: TO 1C-10(K)A-2-33-51
- - - -
A13.4.2. Operational check
A13.4.2.1. Emergency lighting operational checkout
TR: TO 1C-10(K)A-2-33-51
* - - - -
A13.4.3. Troubleshoot - - - -
A13.4.4. Inspect
A13.4.4.1. Solid state dimmer
TR: TO 1C-10(K)A-2-33-49
- - - -
A13.4.4.2. Anti collision light power supply
TR: TO 1C-10(K)A-2-33-45
- - - -
A13.4.4.3. High intensity light controller
TR: TO 1C-10(K)A-2-33-47
- - - -
A13.4.4.4. Emergency lights battery power supply
TR: TO 1C-10(K)A-2-233-51
- - - -
A13.4.5. Remove components
KC-10 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
218Attachment 13
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A13.4.5.1. Solid state dimmer
TR: TO 1C-10(K)A-2-33-49
- - - -
A13.4.5.2. Anti collision light power supply
TR: TO 1C-10(K)A-2-33-45
- - - -
A13.4.5.3. High intensity light controller
TR: TO 1C-10(K)A-2-33-47
- - - -
A13.4.5.4. Emergency lights battery power supply
TR: TO 1C-10(K)A-2-233-51
- - - -
A13.4.5.5. Light bulbs
TR: TO 1C-10(K)A-2-33
- - - -
A13.4.6. Repair components - - - -
A13.4.7. Install components
A13.4.7.1. Solid state dimmer
TR: TO 1C-10(K)A-2-33-49
- - - -
A13.4.7.2. Anti collision light power supply
TR: TO 1C-10(K)A-2-33-45
- - - -
A13.4.7.3. High intensity light controller
TR: TO 1C-10(K)A-2-33-47
- - - -
A13.4.7.4. Emergency lights battery power supply
TR: TO 1C-10(K)A-2-233-51
- - - -
A13.4.7.5. Light bulbs
TR: TO 1C-10(K)A-2-33
- - - -
A13.4.8. Bench check
A13.4.8.1. Operate lighting systems
TR: TO 1C-10(K)A-2-33
- - - -
A13.5. LANDING GEAR SYSTEM
A13.5.1. Operational fundamentals - - - -
A13.5.2. Operational check
A13.5.2.1. Perform BITE check of proximity electronics unit
TR: TO 1C-10(K)A-2-32-61
- - - -
A13.5.2.2. Brake assembly
TR: TO 1C-10(K)A-2-32-40
- - - -
A13.5.3. Troubleshoot Landing gear Systems * - - - -
A13.5.4. Inspect Landing Gear Systems * - - - -
A13.5.5. Remove components
A13.5.5.1. Main Landing Gear Wheel and the Assembly
TR: TO 1C-10(K)A-2-32-41
- - - -
A13.5.5.2. Centerline Landing Gear Wheel and Tire Assembly - - - -
KC-10 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
219Attachment 13
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
TR: TO 1C-10(K)A-2-32-41
A13.5.5.3. Centerline Landing Gear Wheel and Tire Assembly Alternate procedure No. 1
- - - -
A13.5.5.4. Brake assembly
TR: TO 1C-10(K)A-2-32-43
- - - -
A13.5.5.5. Landing gear position and warning proximity electronics unit
TR: 1C-10(K)A-2-32-61
- - - -
A13.5.5.6. Landing gear position indicator
TR: TO 1C-10(K)A-2-32-61
- - - -
A13.5.5.7. Proximity sensors/position switches
TR: TO 1C-10(K)A-2-32-61
- - - -
A13.5.6. Repair components
A13.5.6.1. Centerline landing gear extension and retraction (supervisor)
TR: TO 1C-10(K)A-2-32-38
- - - -
A13.5.7. Install components
A13.5.7.1. Main Landing Gear Wheel and the Assembly
TR: TO 1C-10(K)A-2-32-41
- - - -
A13.5.7.2. Centerline Landing Gear Wheel and Tire Assembly
TR: TO 1C-10(K)A-2-32-41
- - - -
A13.5.7.3. Centerline Landing Gear Wheel and Tire Assembly Alternate procedure No. 1
- - - -
A13.5.7.4. Brake assembly
TR: TO 1C-10(K)A-2-32-43
- - - -
A13.5.7.5. Landing gear position warning proximity electronics unit
TR: 1C-10(K)A-2-32-61
- - - -
A13.5.7.6. Landing gear position indicator
TR: TO 1C-10(K)A-2-32-61
- - - -
A13.5.7.7. Proximity sensors/position switches
TR: TO 1C-10(K)A-2-32-61
- - - -
A13.5.8. Bench check
A13.5.8.1. Centerline landing gear extension and retraction (supervisor)
TR: TO 1C-10(K)A-2-32-38
- - - -
A13.6. ANTI-SKID SYSTEM
A13.6.1. Operational fundamentals - - - -
A13.6.2. Operational check
A13.6.2.1. Perform BITE test of anti-skid control box
TR: TO 1C-10(K)A-2-32-45
- - - -
KC-10 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
220Attachment 13
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A13.6.3. Troubleshoot * - - - -
A13.6.4. Inspect
A13.6.4.1. Anti-skid control box
TR: TO 1C-10(K)A-2-232-45
- - - -
A13.6.4.2. Anti-skid wheel speed transducer
TR: TO 1C-10(K)A-2-32-45
* - - - -
A13.6.5. Remove components
A13.6.5.1. Anti-skid control box
TR: TO 1C-10(K)A-2-232-45
- - - -
A13.6.5.2. Anti-skid wheel speed transducer
TR: TO 1C-10(K)A-2-32-45
- - - -
A13.6.6. Repair components - - - -
A13.6.7. Install components
A13.6.7.1. Anti-skid control box
TR: TO 1C-10(K)A-2-232-45
- - - -
A13.6.7.2. Anti-skid wheel speed transducer
TR: TO 1C-10(K)A-2-32-45
- - - -
A13.6.8. Bench check - - - -
A13.7. NOSE GEAR SYSTEM
A13.7.1. Operational fundamentals - - - -
A13.7.2. Operational check - - - -
A13.7.3. Troubleshoot - - - -
A13.7.4. Inspect
A13.7.4.1. Nose Landing Gear Wheel and Tire Assembly
TR: TO 1C-10(K)A-2-32-41
- - - -
A13.7.5. Remove components
A13.7.5.1. Nose Landing Gear Wheel and Tire Assembly
TR: TO 1C-10(K)A-2-32-41
- - - -
A13.7.6. Repair components - - - -
A13.7.7. Install components
A13.7.7.1. Nose Landing Gear Wheel and Tire Assembly
TR: TO 1C-10(K)A-2-32-41
- - - -
A13.7.8. Bench check
A13.7.8.1. Nose and main landing gear extension and retraction (supervisor)
TR: TO 1C-10(K)A-2-32-30
- - - -
A13.7.8.2. Nose and main landing gear extension and retraction (handle operator)
TR: TO 1C-10(K)A-2-32-30
- - - -
KC-10 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
221Attachment 13
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A13.8. PRIMARY AND SECONDARY FLIGHT CONTROL SYSTEMS
A13.8.1. Operational fundamentals
A13.8.1.1. Auto-spoiler system operational fundamentals
TR: TO 1C-10(K)A-2-27-60
- - - -
A13.8.2. Auto-spoiler system operational checkout
TR: TO 1C-10(K)A-2-27-63
* - - - -
A13.8.3. Troubleshoot Auto-spoiler system
TR: TO 1C-10(K)A-2-27-60-TAFI
- - - -
A13.8.4. Inspect
TR: 1C-10(K)A-6-WC-1, 1C-10(K)A-3-1, 1C-10(K)A-3-2 and 1C-10(K)A-3-3
A13.8.4.1. Aileron - - - -
A13.8.4.2. Rudder - - - -
A13.8.4.3. Elevator - - - -
A13.8.4.4. Flaps - - - -
A13.8.4.5. Slats - - - -
A13.8.4.6. Spoilers - - - -
A13.8.4.7. Auto-spoiler control box
TR: TO 1C-10(K)A-2-27-63
- - - -
A13.8.4.8. Spoiler electric actuator
TR: TO 1C-10(K)A-2-227-63
- - - -
A13.8.4.9. Horizontal stabilizer - - - -
A13.8.5. Remove components
A13.8.5.1. Auto-spoiler control box
TR: TO 1C-10(K)A-2-27-63
- - - -
A13.8.5.2. Spoiler electric actuator
TR: TO 1C-10(K)A-2-227-63
- - - -
A13.8.6. Repair components - - - -
A13.8.7. Install components
A13.8.7.1. Auto-spoiler control box
TR: TO 1C-10(K)A-2-27-63
- - - -
A13.8.7.2. Spoiler electric actuator
TR: TO 1C-10(K)A-2-227-63
- - - -
A13.8.8. Bench check - - - -
A13.9. OVERHEAT/FIRE WARNING SYSTEM
A13.9.1 Operational fundamentals - - - -
A13.9.2. Operational check * - - - -
A13.9.3. Troubleshoot - - - -
KC-10 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
222Attachment 13
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A13.9.4. Inspect System Components * - - - -
A13.9.5. Remove components - - - -
A13.9.6. Repair components - - - -
A13.9.7. Install components - - - -
A13.9.8. Bench check - - - -
A13.9.9. Operate smoke detection system
TR: TO 1C-10(K)A-2-26
- - - -
A13.9.10. Operate fire detection system (A and B loops)
TR: TO 1C-10(K)A-2-26
- - - -
A13.10. FIRE EXTINGUISHING SYSTEM
A13.10.1. Operational fundamentals - - - -
A13.10.2. Operational check - - - -
A13.10.3. Troubleshoot - - - -
A13.10.4. Inspect System Components * - - - -
A13.10.5. Remove components - - - -
A13.10.6. Repair components - - - -
A13.10.7. Install components - - - -
A13.10.8. Bench check - - - -
A13.11. TAKEOFF WARNING SYSTEM
A13.11.1. Operational fundamentals - - - -
A13.11.2. Operational check - - - -
A13.11.3. Troubleshoot - - - -
A13.11.4. Inspect System Components - - - -
A13.11.5. Remove components - - - -
A13.11.6. Repair components - - - -
A13.11.7. Install components - - - -
A13.11.8. Bench check - - - -
A13.11.9. Component location - - - -
A13.12. MASTER CAUTION/WARNING SYSTEM
A13.12.1. Operational fundamentals - - - -
A13.12.2. Operational check * - - - -
A13.12.3. Troubleshoot - - - -
A13.12.4. Inspect
A13.12.4.1. Master warning and caution controller
TR: TO 1C-10(K)A-2-33-15
- - - -
A13.12.4.2. Aux warning and caution controller
TR: TO 1C-10(K)A-2-33-15
- - - -
A13.12.4.3. Pilot/co-pilot overheat annunciator panel - - - -
KC-10 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
223Attachment 13
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
TR: TO 1C-10(K)A-2-33-15
A13.12.4.4. Landing gear position and warning proximity electronics unit
TR: 1C-10(K)A-2-32-61
- - - -
A13.12.5. Remove components
A13.12.5.1. Master warning and caution controller
TR: TO 1C-10(K)A-2-33-15
- - - -
A13.12.5.2. Aux warning and caution controller
TR: TO 1C-10(K)A-2-33-15
- - - -
A13.12.5.3. Pilot/co-pilot overheat annunciator panel
TR: TO 1C-10(K)A-2-33-15
- - - -
A13.12.6. Repair components - - - -
A13.12.7. Install components
A13.12.7.1. Master warning and caution controller
TR: TO 1C-10(K)A-2-33-15
- - - -
A13.12.7.2. Aux warning and caution controller
TR: TO 1C-10(K)A-2-33-15
- - - -
A13.12.7.3. Pilot/co-pilot overheat annunciator panel
TR: TO 1C-10(K)A-2-33-15
- - - -
A13.12.8. Bench check - - - -
A13.12.9. Operate warning and indicator lights
TR: TO 1C-10(K)A-2-33
- - - -
A13.13. DOOR CONTROL AND WARNING SYSTEM
A13.13.1. Operational fundamentals - - - -
A13.13.2. Operational check - - - -
A13.13.3. Troubleshoot - - - -
A13.13.4. Inspect System Components - - - -
A13.13.5. Remove components - - - -
A13.13.6. Repair components - - - -
A13.13.7. Install components - - - -
A13.13.8. Bench check - - - -
A13.13.9. Operate passenger doors
TR: TO 1C-10(K)A-2-52
- - - -
A13.13.10. Operate cargo door
TR: TO 1C-10(K)A-2-52
- - - -
A13.13.11. Raise/lower to/from maintenance position air refueling operators door
TR: TO 1C-10(K)A-2-52
- - - -
A13.14. FUEL WARNING AND CONTROL SYSTEM
KC-10 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
224Attachment 13
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A13.14.1. Operational fundamentals - - - -
A13.14.2. Operational check - - - -
A13.14.3. Troubleshoot - - - -
A13.14.4. Inspect System Components - - - -
A13.14.5. Remove components
A13.14.5.1. Flight engineers fuel panel switches
TR: TO 1C-10(K)A-2-110-28
- - - -
A13.14.6. Repair components
A13.14.6.1. Flight engineers fuel panel switches
TR: TO 1C-10(K)A-2-110-28
- - - -
A13.14.7. Install components
A13.14.7.1. Flight engineers fuel panel switches
TR: TO 1C-10(K)A-2-110-28
- - - -
A13.14.8. Bench check - - - -
A13.15. START AND IGNITION SYSTEM
A13.15.1. Operational fundamentals - - - -
A13.15.2. Operational check - - - -
A13.15.3. Troubleshoot - - - -
A13.15.4. Inspect System Components - - - -
A13.15.5. Remove components - - - -
A13.15.6. Repair components - - - -
A13.15.7. Install components - - - -
A13.15.8. Bench check - - - -
A13.16. NESA ANTI-ICING SYSTEM
A13.16.1. Operational fundamentals - - - -
A13.16.2. Operational check - - - -
A13.16.3. Troubleshoot - - - -
A13.16.4. Inspect System Components - - - -
A13.16.5. Remove components - - - -
A13.16.6. Repair components - - - -
A13.16.7. Install components - - - -
A13.16.8. Bench check - - - -
A13.17. BLEED AIR DISTRIBUTION SYSTEM
A13.17.1. Operational fundamentals
A13.17.1.1. Manifold failure detection operational fundamentals
TR: 1C-10(K)A-2-36-23
- - - -
A13.17.1.2. Manifold isolation operational fundamentals
TR: TO 1C-10(K)A-2-36-15
- - - -
KC-10 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
225Attachment 13
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A13.17.2. Operational check
A13.17.2.1. Perform BITE test of pneumatic system
TR: TO 1C-10(K)A-2-36-00
- - - -
A13.17.2.2. Operate AV-102 Pneumatic System tester with engines operating
TR: TO 1C-10(K)A-2-36-TAFI
- - - -
A13.17.2.3. Manifold failure detection system operational checkout
TR: TO 1C-10(K)A-2-36-23
* - - - -
A13.17.3. Troubleshoot * - - - -
A13.17.4. Inspect
A13.17.4.1. Pneumatic system controller
TR: TO 1C-10(K)A-2-36-27
- - - -
A13.17.4.2. Pressure regulator valve
TR: TO 1C-10(K)A-2-236-12
- - - -
A13.17.4.3. High pressure bleed valve
TR: TO 1C-10(K)A-2-36-11
- - - -
A13.17.4.4. Fan air valve
TR: TO 1C-10(K)A-2-36-13
- - - -
A13.17.4.5. Over pressure valve
TR: TO 1C-10(K)A-2-36-12
- - - -
A13.17.4.6. Pre-cooler assembly
TR: TO 1C-10(K)A-2-36-13
- - - -
A13.17.4.7. Regulated pressure sensor
TR: TO 1C-10(K)A-2-36-27
- - - -
A13.17.4.8. High stage temperature sensor
TR: TO 1C-10(K)A-2-36-11
- - - -
A13.17.4.9. Manifold failure detector controller
TR: TO 1C-10(K)A-2-36-23
- - - -
A13.17.4.10. Manifold fail press to test switch
TR: TO 1C-10(K)A-2-23
- - - -
A13.17.4.12. Manifold isolation valves
TR: TO 1C-10(K)A-2-36-15
- - - -
A13.17.4.13. Manifold fail pressure switch
TR: TO 1C-10(K)A-2-36-23
- - - -
A13.17.4.14. Manifold fail thermal switch
TR: TO 1C-10(K)A-2-236-23
- - - -
A13.17.4.15. Manifold failure detector loop elements
TR: TO 1C-10(K)A-2-36-23
- - - -
KC-10 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
226Attachment 13
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A13.17.5. Remove components
A13.17.5.1. Pneumatic system controller
TR: TO 1C-10(K)A-2-36-27
- - - -
A13.17.5.2. Pressure regulator valve
TR: TO 1C-10(K)A-2-236-12
- - - -
A13.17.5.3. High pressure bleed valve
TR: TO 1C-10(K)A-2-36-11
- - - -
A13.17.5.4. Fan air valve
TR: TO 1C-10(K)A-2-36-13
- - - -
A13.17.5.5. Over pressure valve
TR: TO 1C-10(K)A-2-36-12
- - - -
A13.17.5.6. Pre-cooler assembly
TR: TO 1C-10(K)A-2-36-13
- - - -
A13.17.5.7. Regulated pressure sensor
TR: TO 1C-10(K)A-2-36-27
- - - -
A13.17.5.8. High stage temperature sensor
TR: TO 1C-10(K)A-2-36-11
- - - -
A13.17.5.9. Manifold failure detector controller
TR: TO 1C-10(K)A-2-36-23
- - - -
A13.17.5.10. Manifold fail press to test switch
TR: TO 1C-10(K)A-2-23
- - - -
A13.17.5.11. Manifold isolation valves
TR: TO 1C-10(K)A-2-36-15
- - - -
A13.17.5.12. Manifold fail pressure switch
TR: TO 1C-10(K)A-2-36-23
- - - -
A13.17.5.13. Manifold fail thermal switch
TR: TO 1C-10(K)A-2-236-23
- - - -
A13.17.5.14. Manifold failure detector loop elements
TR: TO 1C-10(K)A-2-36-23
- - - -
A13.17.6. Repair components - - - -
A13.17.7. Install components
A13.17.7.1. Pneumatic system controller
TR: TO 1C-10(K)A-2-36-27
- - - -
A13.17.7.2. Pressure regulator valve
TR: TO 1C-10(K)A-2-236-12
- - - -
A13.17.7.3. High pressure bleed valve
TR: TO 1C-10(K)A-2-36-11
- - - -
A13.17.7.4. Fan air valve - - - -
KC-10 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
227Attachment 13
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
TR: TO 1C-10(K)A-2-36-13
A13.17.7.5. Over pressure valve
TR: TO 1C-10(K)A-2-36-12
- - - -
A13.17.7.6. Pre-cooler assembly
TR: TO 1C-10(K)A-2-36-13
- - - -
A13.17.7.7. Regulated pressure sensor
TR: TO 1C-10(K)A-2-36-27
- - - -
A13.17.7.8. High stage temperature sensor
TR: TO 1C-10(K)A-2-36-11
- - - -
A13.17.7.9. Manifold failure detector controller
TR: TO 1C-10(K)A-2-36-23
- - - -
A13.17.7.10 Manifold fail press to test switch
TR: TO 1C-10(K)A-2-23
- - - -
A13.17.7.11. Manifold isolation valves
TR: TO 1C-10(K)A-2-36-15
- - - -
A13.17.7.12. Manifold fail pressure switch
TR: TO 1C-10(K)A-2-36-23
- - - -
A13.17.7.13. Manifold fail thermal switch
TR: TO 1C-10(K)A-2-236-23
- - - -
A13.17.7.14. Manifold failure detector loop elements
TR: TO 1C-10(K)A-2-36-23
- - - -
A13.17.8. Bench check - - - -
A13.17.9. Operate bleed air system
TR: TO 1C-10(K)A-2-36
* - - - -
A13.18. AIR CONDITIONING SYSTEM
A13.18.1. Operational fundamentals - - - -
A13.18.2. Operational check
A13.18.2.1. Pack condition indication system operational checkout
TR: TO 1C-10(K)A-2-221-50
- - - -
A13.18.2.2. Trim air system operational checkout
TR: TO 1C-10(K)A-2-21-21
- - - -
A13.18.2.3. Perform BITE test of air conditioning system
TR: TO 1C-10(K)A-2-21-60
- - - -
A13.18.3. Troubleshoot - - - -
A13.18.4. Inspect
A13.18.4.1. Trim air valve
TR: TO 1C-10(K)A-2-21-62
- - - -
A13.18.4.2. APU and pack demand temperature controller - - - -
KC-10 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
228Attachment 13
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
TR: 1C-10(K)A-2-21-60
A13.18.4.3. Zone temperature controller
TR: TO 1C-10(K)A-2-21-62
- - - -
A13.18.4.4. Pack temperature controller
TR: TO 1C-10(K)A-2-221-62
- - - -
A13.18.4.5. Zone and duct temperature sensors
TR: TO 1C-10(K)A-2-21-64
- - - -
A13.18.4.6. Ram air plenum
TR: TO 1C-10(K)A-2-21-53
- - - -
A13.18.4.7. Pack heat exchanger
TR: TO 1C-10(K)A-2-21-53
- - - -
A13.18.4.8. Rate of flow control valve
TR: TO 1C-10(K)A-2-21-51
- - - -
A13.18.4.9. Control valve
TR: TO 1C-10(K)A-2-21-51
- - - -
A13.18.4.10. Turbine by-pass valve
TR: TO 1C-10(K)A-2-221-62
- - - -
A13.18.4.11. Turbine by-pass valve/pack inlet and exhaust door actuator
TR: TO 1C-10(K)A-2-21-62
- - - -
A13.18.4.12. Anti-ice valve
TR: TO 1C-10(K)A-2-21-53
- - - -
A13.18.4.13. Pack overheat thermostat
TR: TO 1C-10(K)A-2-21-53
- - - -
A13.18.4.14. Equipment Cooling - - - -
A13.18.4.15. Center Accessory Compartment (CAC) fan
TR: TO 1C-10(K)A-2-21-26
- - - -
A13.18.4.16. CAC flow detector
TR: TO 1C-10(K)A-2-21-26
- - - -
A13.18.4.17. Radio rack fan
TR: TO 1C-10(K)A-2-21-26
- - - -
A13.18.4.18. Radio rack fan flow detector
TR: TO 1C-10(K)A-2-21-26
- - - -
A13.18.4.19. Inertial navigation (1NU) fan
TR: TO 1C-10(K)A-2-21-26
- - - -
A13.18.4.20. (INU) fan start capacitor
TR: TO 1C-10(K)A-2-110-21 and 1-1A-14
- - - -
A13.18.4.21. (INU) fan flow detector
TR: TO 1C-10(K)A-2-21-26
- - - -
KC-10 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
229Attachment 13
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A13.18.4.22. Center instrument panel fan
TR: TO 1C-10(K)A-2-21-28
- - - -
A13.18.4.23. Center instrument panel fan filter
TR: TO 1C-10(K)A-2-28
- - - -
A13.18.5. Remove components
A13.18.5.1. Trim air valve
TR: TO 1C-10(K)A-2-21-62
- - - -
A13.18.5.2. APU and pack demand temperature controller
TR: 1C-10(K)A-2-21-60
- - - -
A13.18.5.3. Zone temperature controller
TR: TO 1C-10(K)A-2-21-62
- - - -
A13.18.5.4. Pack temperature controller
TR: TO 1C-10(K)A-2-221-62
- - - -
A13.18.5.5. Zone and duct temperature sensors
TR: TO 1C-10(K)A-2-21-64
- - - -
A13.18.5.6. Ram air plenum
TR: TO 1C-10(K)A-2-21-53
- - - -
A13.18.5.7. Pack heat exchanger
TR: TO 1C-10(K)A-2-21-53
- - - -
A13.18.5.8. Rate of flow control valve
TR: TO 1C-10(K)A-2-21-51
- - - -
A13.18.5.9. Control valve
TR: TO 1C-10(K)A-2-21-51
- - - -
A13.18.5.10. Turbine by-pass valve
TR: TO 1C-10(K)A-2-221-62
- - - -
A13.18.5.11. Turbine by-pass valve/pack inlet and exhaust door actuator
TR: TO 1C-10(K)A-2-21-62
- - - -
A13.18.5.12. Anti-ice valve
TR: TO 1C-10(K)A-2-21-53
- - - -
A13.18.5.13. Pack overheat thermostat
TR: TO 1C-10(K)A-2-21-53
- - - -
A13.18.5.14. Equipment Cooling - - - -
A13.18.5.15. Center Accessory Compartment (CAC) fan
TR: TO 1C-10(K)A-2-21-26
- - - -
A13.18.5.16. CAC flow detector
TR: TO 1C-10(K)A-2-21-26
- - - -
A13.18.5.17. Radio rack fan
TR: TO 1C-10(K)A-2-21-26
- - - -
KC-10 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
230Attachment 13
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A13.18.5.18. Radio rack fan flow detector
TR: TO 1C-10(K)A-2-21-26
- - - -
A13.18.5.19. Inertial navigation (1NU) fan
TR: TO 1C-10(K)A-2-21-26
- - - -
A13.18.5.20. (INU) fan start capacitor
TR: TO 1C-10(K)A-2-110-21 and 1-1A-14
- - - -
A13.18.5.21. (INU) fan flow detector
TR: TO 1C-10(K)A-2-21-26
- - - -
A13.18.5.22. Center instrument panel fan
TR: TO 1C-10(K)A-2-21-28
- - - -
A13.18.6. Repair components - - - -
A13.18.7. Install components
A13.18.7.1. Trim air valve
TR: TO 1C-10(K)A-2-21-62
- - - -
A13.18.7.2. APU and pack demand temperature controller
TR: TO 1C-10(K)A-2-21-60
- - - -
A13.18.7.3. Zone temperature controller
TR: TO 1C-10(K)A-2-21-62
- - - -
A13.18.7.4. Pack temperature controller
TR: TO 1C-10(K)A-2-221-62
- - - -
A13.18.7.5. Zone and duct temperature sensors
TR: TO 1C-10(K)A-2-21-64
- - - -
A13.18.7.6. Ram air plenum
TR: TO 1C-10(K)A-2-21-53
- - - -
A13.18.7.7. Pack heat exchanger
TR: TO 1C-10(K)A-2-21-53
- - - -
A13.18.7.8. Rate of flow control valve
TR: TO 1C-10(K)A-2-21-51
- - - -
A13.18.7.9. Control valve
TR: TO 1C-10(K)A-2-21-51
- - - -
A13.18.7.10 Turbine by-pass valve
TR: TO 1C-10(K)A-2-221-62
- - - -
A13.18.7.11. Turbine by-pass valve/pack inlet and exhaust door actuator
TR: TO 1C-10(K)A-2-21-62
- - - -
A13.18.7.12. Anti-ice valve
TR: TO 1C-10(K)A-2-21-53
- - - -
A13.18.7.13. Pack overheat thermostat
TR: TO 1C-10(K)A-2-21-53
- - - -
KC-10 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
231Attachment 13
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A13.18.7.14. Equipment Cooling - - - -
A13.18.7.15. Center Accessory Compartment (CAC) fan
TR: TO 1C-10(K)A-2-21-26
- - - -
A13.18.7.16. CAC flow detector
TR: TO 1C-10(K)A-2-21-26
- - - -
A13.18.7.17. Radio rack fan
TR: TO 1C-10(K)A-2-21-26
- - - -
A13.18.7.18. Radio rack fan flow detector
TR: TO 1C-10(K)A-2-21-26
- - - -
A13.18.7.19. Inertial navigation (1NU) fan
TR: TO 1C-10(K)A-2-21-26
- - - -
A13.18.7.20. (INU) fan start capacitor
TR: TO 1C-10(K)A-2-110-21 and 1-1A-14
- - - -
A13.18.7.21. (INU) fan flow detector
TR: TO 1C-10(K)A-2-21-26
- - - -
A13.18.7.22. Center instrument panel fan
TR: TO 1C-10(K)A-2-21-28
- - - -
A13.18.8. Bench check - - - -
A13.19. PRESSURIZATION SYSTEM
A13.19.1. Operational fundamentals - - - -
A13.19.2. Operational check
A13.19.2.1. Perform BITE test of cabin pressurization system
TR: TO 1C-10(K)A-2-21-31
- - - -
A13.19.3. Troubleshoot * - - - -
A13.19.4. Inspect - - - -
A13.19.4.1. Cabin pressure controller
TR: TO 1C-10(K)A-2-221-31
- - - -
A13.19.4.2. Cabin altitude rate selector
TR: TO 1C-10(K)A-2-21-31
- - - -
A13.19.4.3. Cabin pressure indicator
TR: TO 1C-10(K)A-2-21-31
- - - -
- - - -
A13.19.4.4. Thrust recovery valve actuator
TR: TO 1C-10(K)A-2-21-31
- - - -
A13.19.5. Remove components
A13.19.5.1. Cabin pressure controller
TR: TO 1C-10(K)A-2-221-31
- - - -
A13.19.5.2. Cabin altitude rate selector - - - -
KC-10 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
232Attachment 13
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
TR: TO 1C-10(K)A-2-21-31
A13.19.5.3. Cabin pressure indicator
TR: TO 1C-10(K)A-2-21-31
- - - -
A13.19.5.4. Thrust recovery valve actuator
TR: TO 1C-10(K)A-2-21-31
- - - -
A13.19.6. Repair components - - - -
A13.19.7. Install components
A13.19.7.1. Cabin pressure controller
TR: TO 1C-10(K)A-2-221-31
- - - -
A13.19.7.2. Cabin altitude rate selector
TR: TO 1C-10(K)A-2-21-31
- - - -
A13.19.7.3. Cabin pressure indicator
TR: TO 1C-10(K)A-2-21-31
- - - -
A13.19.7.4. Thrust recovery valve actuator
TR: TO 1C-10(K)A-2-21-31
- - - -
A13.19.8. Bench check - - - -
A13.20. LIQUID COOLANT SYSTEM
A13.20.1. Operational fundamentals - - - -
A13.20.2. Operational check - - - -
A13.20.3. Troubleshoot System - - - -
A13.20.4. Inspect System Components - - - -
A13.20.5. Remove components - - - -
A13.20.6. Repair components - - - -
A13.20.7. Install components - - - -
A13.20.8. Bench check - - - -
A13.21. OXYGEN SYSTEM
A13.21.1. Operational fundamentals
TR: TO 1C-10(K)A-2-235-00
- - - -
A13.21.2. Operational check of oxygen system pressure regulator
TR: TO 1-10(K)A-2-35-12
* - - - -
A13.21.3. Troubleshoot System - - - -
A13.21.4. Inspect System Components * - - - -
A13.21.5. Remove components
A13.21.5.1. Oxygen regulator
TR: TO 1C-10(K)A-2-35-12
- - - -
A13.21.5.2. Oxygen cylinder regulator/re-fill valve
TR: TO 1C-10(K)A-2-235-12
- - - -
KC-10 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
233Attachment 13
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A13.21.5.3. Oxygen cylinders
TR: TO 1C-10K)A-2-35-30
- - - -
A13.21.5.4. Quantity indicator transducer
TR: TO 1C-10(K)A-35-14
- - - -
A13.21.6. Repair components - - - -
A13.21.7. Install components
A13.21.7.1. Oxygen regulator
TR: TO 1C-10(K)A-2-35-12
- - - -
A13.21.7.2. Oxygen cylinder regulator/re-fill valve
TR: TO 1C-10(K)A-2-235-12
- - - -
A13.21.7.3. Oxygen cylinders
TR: TO 1C-10K)A-2-35-30
- - - -
A13.21.7.4. Quantity indicator transducer
TR: TO 1C-10(K)A-35-14
- - - -
A13.21.8. Bench check - - - -
A13.21.9. Operate oxygen system
TR: TO 1C-10(K)A-2-35
- - - -
A13.22. AERIAL REFUELING SYSTEM
A13.22.1. Operational fundamentals - - - -
A13.22.2. Operational check - - - -
A13.22.3. Troubleshoot System components - - - -
A13.22.4. Inspect System components * - - - -
A13.22.5. Remove components - - - -
A13.22.6. Repair components - - - -
A13.22.7. Install components - - - -
A13.22.8. Bench check - - - -
A13.22.9. Boom
A13.22.9.1. Boom Operation : raise lower
TR: TO 1C-10(K)A-2-28 Part III and 1C-10(K)A-2-28CL-1
- - - -
A13.22.9.2. Boom Operation : extend/retract
TR: TO 1C-10(K)A-2-28 Part III and 1C-10(K)A-2-28CL-1
- - - -
- - - -
A13.22.9.3. Operation of ARO Status Test Panel (STP)
TR: TO 1C-10(K)A-2-28-79 (Part II)
- - - -
A13.22.9.4. Service boom Independent Disconnect System (IDS)
TR: TO 1C-10(K)A-2-28-79 (Part II)
- - - -
KC-10 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
234Attachment 13
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A13.22.9.5. Service surge boot
TR: TO 1C-10(K)A-2-28-71-09
- - - -
A13.22.9.6. Clean boom signal coil
TR: TO 1C-10(K)A-2-28-76
- - - -
A13.22.9.7. Deploy boom (swing)
TR: TO 1C-10(K)A-2-28 (Part II) and 1C-10(K)A-2-CL-1
- - - -
A13.22.10. Hose and Drogue
A13.22.10.1. Deploy centerline hose and drogue
TR: TO 1C-10(K)A-2-CL-1
- - - -
A13.22.10.2. Stow centerline hose and drogue
TR: TO 1C-10(K)A-2-CL-1
- - - -
A13.22.10.3. Deploy wing hose and drogue
TR: TO 1C-10(K)A-2-28
- - - -
A13.22.10.4. Stow wing hose and drogue
TR: TO 1C-10(K)A-2-28
- - - -
A13.22.10.5. USARRSI (Universal Air Refueling Receptacle Slipway Installation)
- - - -
A13.22.10.6. Clean UARRSI Signal Coil
TR: TO 1C-10(K)A-2-28-91 (Part II)
- - - -
A13.23. MISCELLANEOUS SYSTEMS
TR:
A13.23.1. Operational fundamentals - - - -
A13.23.2. Operational check - - - -
A13.23.3. Troubleshoot - - - -
A13.23.4. Inspect
A13.23.4.1. Windows/windshield
TR: TO 1C-10(K)A-2-56
- - - -
A13.23.4.2. Rain removal system
TR: TO 1C-10(K)A-2-30
- - - -
A13.23.4.3. Accumulators
TR: TO 1C-10(K)A-2-29 and 1C-10(K)A-2-32
- - - -
A13.23.4.4. Hydraulic system
TR: TO 1C-10(K)A-2-12 and 1C-10(K)A-2-12-2
- - - -
A13.23.5. Remove components
A13.23.5.1. IAW exit sign
TR: TO 1C-10(K)A-2-25-53-05
- - - -
A13.23.5.2. Rain repellant bottle
TR: TO 1C-10(K)A-2-30
- - - -
KC-10 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
235Attachment 13
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A13.23.5.3. Aircrew bunks
TR: TO 1C-10(K)A-2-53-01 and 25-53-03
- - - -
A13.23.5.4. Increased Accommodation Unit (IAU)
TR: 1C-10(K)A-2-25-21
- - - -
A13.23.5.5. IAU passenger oxygen
TR: TO 1C-10(K)A-2-25-53-06
- - - -
A13.23.5.6. IAU seat pallets
TR: 1C-10(K)A-2-25-53-09
- - - -
A13.23.5.7. Cargo Barrier Net
TR: TO 1C-10(K)A-2-25-53-01 and 25-53-03
- - - -
A13.23.5.8. IAU "Z" lav/storage cabinet
TR: TO 1C-10(K)A-2-25-53-07 and 25-53-08
- - - -
A13.23.5.9. Environmental Curtain
TR: TO 1C-10(K)A-2-25-53-01 and 25-53-03
- - - -
A13.23.6. Repair components - - - -
A13.23.7. Install components
A13.23.7.1. IAW exit sign
TR: TO 1C-10(K)A-2-25-53-05
- - - -
A13.23.7.2. Rain repellant bottle
TR: TO 1C-10(K)A-2-30
- - - -
A13.23.7.3. Aircrew bunks
TR: TO 1C-10(K)A-2-53-01 and 25-53-03
- - - -
A13.23.7.4. Increased Accommodation Unit (IAU)
TR: 1C-10(K)A-2-25-21
- - - -
A13.23.7.5. IAU passenger oxygen
TR: TO 1C-10(K)A-2-25-53-06
- - - -
A13.23.7.6. IAU seat pallets
TR: 1C-10(K)A-2-25-53-09
- - - -
A13.23.7.7. Cargo Barrier Net
TR: TO 1C-10(K)A-2-25-53-01 and 25-53-03
- - - -
A13.23.7.8. IAU "Z" lav/storage cabinet
TR: TO 1C-10(K)A-2-25-53-07 and 25-53-08
- - - -
A13.23.7.9. Environmental Curtain
TR: TO 1C-10(K)A-2-25-53-01 and 25-53-03
- - - -
A13.23.8. Bench check - - - -
A13.23.9. Operate rain removal system
TR: TO 1C-10(K)A-2-30
- - - -
A13.23.10. Operate crew member electrically operated/manual seats
- - - -
KC-10 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
236Attachment 13
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
TR: TO 1C-10(K)A-2-25-11-03 thru 25-11-10
A13.23.11. Operate aerial refueling operators station manual seats
TR: TO 1C-10(K)A-2-25-11-11 thru 25-91-04
- - - -
A13.23.12. Operate hydraulic system using auxiliary and reversible pumps
TR: TO 1C-10(K)A-2-29
- - - -
A13.23.13. Raise/lower tail cone
TR: TO 1C-10(K)A-2-53
- - - -
A13.23.14. Operate nose radome
TR: TO 1C-10(K)A-2-52
- - - -
A13.24. COMMON MAINTENANCE PRACTICES
A13.24.1 Inspect/operate portable external electrical power unit
- - - -
A13.24.2 Inspect/use ground maintenance stands - - - -
A13.24.3. Dropped Object Prevention Program (DOPP) - - - -
A13.24.4. Defensive Systems (DS) familiarization (on applicable aircraft)
- - - -
A13.24.5 Apply/disconnect external electrical power unit - - - -
A13.24.6 Perform wing/tail walker duties - - - -
A13.24.7. Team communications - - - -
A13.24.8 Connect/Disconnect External Pneumatics
TR: TO 1C-10(K)A-2-36
- - - -
A13.24.9 Service engine, CSD and APU oil systems (pressure cart method)
TR: TO 1C-10(K)A-2-12 and 1C-10(K)A-2-12-5
- - - -
A13.24.10 Service engine, CSD and APU oil systems(gravity fill method)
TR: TO 1C-10(K)A-2-12 and 1C-10(K)A-2-12-5
- - - -
A13.24.11 Service hydraulic system
TR: TO 1C-10(K)A-2-12 and 1C-10(K)A-2-12-2
- - - -
A13.24.12 Service accumulators
TR: TO 1C-10(K)A-2-28, 1C-10(K)A-2-28 and 1C-10(K)A-2-32
- - - -
A13.24.13 Service gaseous nitrogen
TR: TO 1C-10(K)A-2-28 and 1C-10(K)A-2-32
- - - -
KC-135 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
237Attachment 14
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
ATTACHMENT 14
NOTE 1: In addition to attachment 2, the tasks and knowledge in attachment 8 will be performed by personnel assigned to maintain KC-135 aircraft.
NOTE 2: Users are responsible for annotating training references to identify current references pending STS revision.
NOTE 3: Items marked in columns 2a or 2b marked with a (*R) are optional core tasks for ANG and AFRC.
NOTE 4: Address comments and recommended changes through Unit Training Managers to the MAJCOM Maintenance Training Manager @ HQ AMC/LGMMT, 402Drive Unit 2A2, Scott AFB, IL 62225-5308; or call DSN 576-4787. MAJCOM Training and Functional Managers forward inputs to the AETC Training Manager, DSNA14.1. METERS AND TESTERS TR: Applicable 33
series TOsA14.1.1. Use decade box - - - -
A14.1.2. Use anti-skid tester - - - -
A14.1.3. Use transformer-rectifier load bank - - - -
A14.1.4. Use wheatstone bridge - - - -
A14.2. AC POWER SYSTEM TR: Applicable KC-135TOs, 8 series component TOs
A14.2.1. Operational fundamentals - - - -
A14.2.2. Operational check System * - - - -
A14.2.3. Troubleshoot System - - - -
A14.2.4. Inspect System Components * - - - -
A14.2.5. Operate Load Bank * - - - -
A14.2.6 Remove components
A14.2.6.1. Generator breaker - - - -
A14.2.6.2. IDG - - - -
A14.2.6.3 BPCU - - - -
A14.2.6.4 Bus-Tie Circuit Breaker - - - -
A14.2.6.5 GCU - - - -
A14.2.6.6 Current Transformer - - - -
A14.2.6.7 S/V box - - - -
A14.2.6.8 Copilot instrument generator - - - -
A14.2.6.9 Other system components - - - -
A14.2.7 Repair components - - - -
A14.2.8 Install Components
A14.2.8.1. Generator breaker - - - -
A14.2.8.2. IDG - - - -
A14.2.8.3 BPCU - - - -
A14.2.8.4 Bus-Tie Circuit Breaker - - - -
A14.2.8.5 GCU - - - -
A14.2.8.6 Current Transformer - - - -
A14.2.8.7 S/V box - - - -
A14.2.8.8 Copilot instrument generator - - - -
KC-135 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
238Attachment 14
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A14.2.8.9 Other system components - - - -
A14.2.9. Bench check components - - - -
A14.3. DC POWER SYSTEM TR: Applicable KC-135TOs, 8 series component TOs
A14.3.1. Operational fundamentals - - - -
A14.3.2. Operational check (use load bank) * - - - -
A14.3.3. Troubleshoot System - - - -
A14.3.4. Inspect System Components * - - - -
A14.3.5. Remove components
A14.3.5.1. Transformer rectifier - - - -
A14.3.5.2. Other system components - - - -
A14.3.6. Repair components - - - -
A14.3.5. Install components
A14.3.7.1 Transformer rectifier - - - -
A14.3.7.2. Other system components - - - -
A14.3.8. Bench check components - - - -
A14.4. EXTERNAL POWER SYSTEM TR: ApplicableKC-135 TOs, 8 series component TOs
A14.4.1. Operational fundamentals - - - -
A14.4.2. Operational Check System * - - - -
A14.4.3. Troubleshoot System - - - -
A14.4.4. Inspect System Components * - - - -
A14.4.5. Remove components - - - -
A14.4.6. Repair components - - - -
A14.4.7. Install components - - - -
A14.4.8. Bench check components - - - -
A14.5. LIGHTING SYSTEM TR: Applicable KC-135TOs,8 series component TOs
A14.5.1. Operational fundamentals - - - -
A14.5.2. Operational check
A14.5.2.1. External * - - - -
A14.5.2.2. Internal * - - - -
A14.5.3. Troubleshoot - - - -
A14.5.4. Inspect * - - - -
A14.5.5. Remove components
A14.5.5.1. Pilot director lights - - - -
A14.5.5.2. Boom/drogue lights - - - -
A14.5.5.3. Light Assembly - - - -
A14.5.5.4. Power Supply - - - -
A14.5.5.5. Dimmer Control Unit - - - -
KC-135 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
239Attachment 14
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A14.5.5.6. Flasher Assembly - - - -
A14.5.6. Repair components - - - -
A14.5.7. Install components
A14.5.7.1. Pilot director lights - - - -
A14.5.7.2. Boom/drogue lights - - - -
A14.5.7.3. Light Assembly - - - -
A14.5.7.4. Power Supply - - - -
A14.5.7.5. Dimmer Control Unit - - - -
A14.5.7.6. Flasher Assembly - - - -
A14.5.8. Bench check components - - - -
A14.6. LANDING GEAR SYSTEM TR: Applicable KC-135 TOs, 8 series component TOs
A14.6.1. Operational fundamentals - - - -
A14.6.2. Operational check
A14.6.2.1. Landing Gear System */R
- - - -
A14.6.2.2. Safety switch - - - -
A14.6.2.3. Truck leveling switch - - - -
A14.6.2.4. Position A/B */R
- - - -
A14.6.3. Troubleshoot * - - - -
A14.6.4. Inspect System Components * - - - -
A14.6.5. Lever lock solenoid circuit checkout - - - -
A14.6.6. Remove components
A14.6.6.1. Safety switch * - - - -
A14.6.6.2. Lever lock solenoid - - - -
A14.6.7. Repair components - - - -
A14.6.8. Install components
A14.6.8.1. Safety switch * - - - -
A14.6.8.2. Lever lock solenoid - - - -
A14.6.9. Bench check components - - - -
A14.7. ANTI-SKID SYSTEM TR: Applicable KC-135TOs, 8 series component TOs
A14.7.1. Operational fundamentals - - - -
A14.7.2. Operational check * - - - -
A14.7.3. Troubleshoot * - - - -
A14.7.4. Inspect System Components * - - - -
A14.7.5. Remove components
A14.7.5.1. Anti-skid detector * - - - -
A14.7.5.1. Anti-skid Shield - - - -
KC-135 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
240Attachment 14
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A14.7.5.2. Other system components - - - -
A14.7.6. Repair components - - - -
A14.7.7. Install components
A14.7.7.1. Anti-skid detector * - - - -
A14.7.7.1. Anti-skid Shield - - - -
A14.7.7.2. Other system components - - - -
A14.7.8. Bench check components - - - -
A14.8. NOSE GEAR STEERING SYSTEM TR:Applicable KC-135 TOs, 8 series component TOs
A14.8.1. Operational fundamentals - - - -
A14.8.2. Operational check - - - -
A14.8.3. Troubleshoot * - - - -
A14.8.4. Inspect System Components * - - - -
A14.8.5. Remove Components
A14.8.5.1 Linear Actuator - - - -
A14.8.5.2. Other components - - - -
A14.8.6. Repair components - - - -
A14.8.7. Install Components
A14.8.7.1 Linear Actuator - - - -
A14.8.7.2 Other components - - - -
A14.8.8. Bench check components - - - -
A14.9. PRIMARY FLIGHT CONTROL SYSTEM TR:Applicable KC-135 TOs, 8 series component TOs
A14.9.1. Operational fundamentals - - - -
A14.9.2. Operational Check System */R
- - - -
A14.9.3. Troubleshoot System * - - - -
A14.9.4. Inspect System Components * - - - -
A14.9.5. Remove Stab trim control switch * - - - -A14.9.6 Install Stab trim control switch * - - - -
A14.9.7. Repair components - - - -
A14.9.8. Bench check components - - - -
A14.10. SECONDARY FLIGHT CONTROL SYSTEM TR:Applicable KC-135 TOs, 8 series component TOs
A14.10.1. Operational fundamentals - - - -
A14.10.2. Operational check
A14.10.2.1. Flaps - - - -
A14.10.2.2. Other system components - - - -
A14.10.3. Troubleshoot
A14.10.3.1. Flaps - - - -
KC-135 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
241Attachment 14
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A14.10.3.2. Other System components - - - -
A14.10.4. Inspect System components * - - - -
A14.10.5. Remove components - - - -
A14.10.6. Install components - - - -
A14.10.7. Repair components - - - -
A14.10.8. Bench check components - - - -
A14.11. OVERHEAT/FIRE WARNING SYSTEM TR:Applicable KC-135 TOs, 8 series component TOs
A14.11.1. Operational fundamentals - - - -
A14.11.2. Operational check System * - - - -
A14.11.3. Troubleshoot System * - - - -
A14.11.4. Inspect System Components * - - - -
A14.11.5. Remove components
A14.11.5.1 Fire Detection Control Unit - - - -
A14.11.5.2 Fire Handle - - - -
A14.11.5.3 Overheat Detectors - - - -
A14.11.5.4 Sensing Elements - - - -
A14.11.5.5 Other System Components - - - -
A14.11.6. Repair components - - - -
A14.11.7. Install components
A14.11.7.1 Fire Detection Control Unit - - - -
A14.11.7.2 Fire Handle - - - -
A14.11.7.3 Overheat Detectors - - - -
A14.11.7.4 Sensing Elements - - - -
A14.11.7.5 Other System Components - - - -
A14.11.8 Bench check components - - - -
A14.12 FIRE EXTINGUISHING SYSTEM TR:
A14.12.1 Operational fundamentals - - - -A14.12.1.1 Engine System - - - -
A14.12.1.2 APU System - - - -
A14.12.1.3 Other fire extinguishing system - - - -
A14.12.2 Operational/continuity check
A14.12.2.1 Engine System - - - -
A14.12.2.2 APU System - - - -
A14.12.2.3 Squib/cartridge electrical circuit * - - - -
A14.12.2.4 Other fire extinguishing system - - - -
A14.12.3 Troubleshoot
A14.12.3.1 Engine System - - - -
KC-135 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
242Attachment 14
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A14.12.3.2 APU System - - - -
A14.12.3.2 Other fire extinguishing system - - - -
A14.12.4 Inspect Fire extinguishing system
A14.12.4.1 Engine System - - - -
A14.12.4.2 APU System - - - -
A14.12.4.3 Squib/Cartridge * - - - -
A14.12.4.4 Other fire extinguishing system - - - -
A14.12.5 Remove components
A14.12.5.1 Engine fire bottle - - - -
A14.12.5.2 APU fire bottle - - - -
A14.12.5.3 Squib/cartridge electrical circuit * - - - -
A14.12.5.4 Other fire extinguishing system - - - -
A14.12.6 Install components
A14.12.6.1 Engine fire bottle - - - -
A14.12.6.2 APU fire bottle - - - -
A14.12.6.3 Squib/cartridge electrical circuit * - - - -
A14.12.6.4 Other fire extinguishing system - - - -
A14.13 TAKEOFF WARNING SYSTEM TR: ApplicableKC-135 TOs, 8 series component TOs
A14.13.1 Operational fundamentals - - - -
A14.13.2 Operational Check System - - - -
A14.13.3 Troubleshoot System * - - - -
A14.13.4 Inspect System Components * - - - -
A14.13.5 Remove components - - - -
A14.13.6 Repair components - - - -
A14.13.7 Install components - - - -
A14.13.8 Bench check components - - - -
A14.14 FUEL WARNING AND CONTROL SYSTEM TR:Applicable KC-135 TOs, 8 series component TOs
A14.14.1 Operational fundamentals - - - -
A14.14.2 Operational check System */R
- - - -
A14.14.3 Troubleshoot System * - - - -
A14.14.4 Inspect System Components * - - - -
A14.14.5 Remove components
A14.14.5.1 Fuel management switch - - - -
A14.14.5.2 Other system components - - - -
A14.14.6 Repair components - - - -
A14.14.7 Install components
A14.14.7.1 Fuel management switch - - - -
KC-135 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
243Attachment 14
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A14.14.7.2 Other system components - - - -
A14.14.8 Bench check components - - - -
A14.15 CARGO DOOR CONTROL AND WARNINGSYSTEM TR: Applicable KC-135 TOs, 8 seriescomponent TOs
A14.15.1 Operational fundamentals - - - -
A14.15.2 Operational check System - - - -
A14.15.3 Troubleshoot System * - - - -
A14.15.4 Inspect System Components * - - - -
A14.15.5 Remove components - - - -
A14.15.6 Repair components - - - -
A14.15.7 Install components - - - -
A14.15.8 Bench check components - - - -
A14.16 START AND IGNITION SYSTEM TR: ApplicableKC-135 TOs, 8 series component TOs
A14.16.1 Operational fundamentals - - - -
A14.16.2 Troubleshoot
A14.16.2.1 Jet engine - - - -
A14.16.2.2 Auxiliary power unit - - - -
A14.16.3 Inspect System Components - - - -
A14.16.4 Remove components - - - -
A14.16.5 Repair components - - - -
A14.16.6 Install components - - - -
A14.16.7 Bench check components - - - -
A14.17 NESA ANTI-ICING SYSTEM TR: Applicable KC-135 TOs, 8 series component TOs
A14.17.1 Operational fundamentals - - - -
A14.17.2 Operational Check System (includes resistancecheck)
* - - - -
A14.17.3 Troubleshoot System * - - - -
A14.17.4 Inspect System Components * - - - -
A14.17.5 Remove components
A14.17.5.1 Transformer - - - -
A14.17.5.2 Controller - - - -
A14.17.5.3 Thermal Switch - - - -
A14.17.5.4 Other System Components - - - -
A14.17.6 Repair components - - - -
A14.17.7 Install components
A14.17.7.1 Transformer - - - -
A14.17.7.2 Controller - - - -
A14.17.7.3 Thermal Switch - - - -
KC-135 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
244Attachment 14
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A14.17.7.4 Other System Components - - - -
A14.17.8 Bench check components - - - -
A14.18. BLEED AIR DISTRIBUTION SYSTEM TR:Applicable KC-135 TOs, 8 series component TOs
A14.18.1 Operational fundamentals - - - -
A14.18.2 Operational check System * - - - -
A14.18.3 Perform leakage checks * - - - -
A14.18.4 Troubleshoot System * - - - -
A14.18.5 Inspect System Components * - - - -
A14.18.6 Remove components
A14.18.6.1 Bleed air duct * - - - -
A14.18.6.2 Bleed air shutoff valve - - - -
A14.18.6.3 Engine Pre-cooler - - - -
A14.18.6.4 Check Valves - - - -
A14.18.6.5 Manifold Valve - - - -
A14.18.6.6 Pressure Regulator - - - -A14.18.6.7 Filters - - - -A14.18.6.8 Other System Components - - - -
A14.18.7 Repair components - - - -
A14.18.8 Hydrostatic Check Ducts - - - -
A14.18.9 Install components
A14.18.9.1 Bleed air duct * - - - -
A14.18.9.2 Bleed air shutoff valve - - - -
A14.18.9.3 Engine Pre-cooler - - - -
A14.18.9.4 Check Valves - - - -
A14.18.9.5 Manifold Valve - - - -
A14.18.9.6 Pressure Regulator - - - -A14.18.9.7 Filters - - - -A14.18.9.8 Other System Components - - - -
A14.18.10 Bench check components - - - -
A14.19. AIR CONDITIONING SYSTEM TR: ApplicableKC-135 TOs, 8 series component TOs
A14.19.1 Operational fundamentals - - - -
A14.19.2 Operational Check System * - - - -
A14.19.3 Perform System Leakage checks * - - - -
A14.19.4 Troubleshoot System * - - - -
A14.19.5 Inspect System Components * - - - -
A14.19.6 Remove components
A14.19.6.1 Water separator coalescer * - - - -
KC-135 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
245Attachment 14
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A14.19.6.2 Water separator - - - -
A14.19.6.3 Flow control valve - - - -
A14.19.6.4 Auxiliary heat valve - - - -
A14.19.6.5 Air cycle machine - - - -
A14.19.6.6 Primary heat exchanger - - - -
A14.19.6.7 Secondary heat exchanger - - - -
A14.19.6.8 Bypass Valve - - - -
A14.19.6.9 Temp Sensor - - - -
A14.19.6.10 35 Degree Control Valve - - - -A14.19.6.11 Ejector Valve - - - -
A14.19.6.12 Ram Air Valve - - - -
A14.19.6.13 Filters - - - -
A14.19.6.14 Other System Components - - - -
A14.19.7 Repair Components - - - -
A14.19.8 Remove and install components
A14.19.8.1 Water separator coalescer * - - - -
A14.19.8.2 Water separator - - - -
A14.19.8.3 Flow control valve - - - -
A14.19.8.4 Auxiliary heat valve - - - -
A14.19.8.5 Air cycle machine - - - -
A14.19.8.6 Primary heat exchanger - - - -
A14.19.8.7 Secondary heat exchanger - - - -
A14.19.8.8 Bypass Valve - - - -
A14.19.8.9 Temp Sensor - - - -
A14.19.8.10 35 Degree Control Valve - - - -A14.19.8.11 Ejector Valve - - - -
A14.19.8.12 Ram Air Valve - - - -
A14.19.8.13 Filters - - - -
A14.19.8.14 Other System Components - - - -
A14.19.9 Bench check components - - - -
A14.20. PRESSURIZATION SYSTEM TR: Applicable KC-135 TOs, 8 series component TOs
A14.20.1 Operational fundamentals - - - -
A14.20.1.2 Pressurization Safety */R
- - - -
A14.20.2 Operational Check System */R
- - - -
A14.20.3 Troubleshoot System * - - - -
A14.20.4 Inspect System Components * - - - -
A14.20.5 Remove components
KC-135 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
246Attachment 14
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A14.20.5.1 Outflow valve - - - -
A14.20.5.2 Pneumatic relay - - - -
A14.20.5.3 Auto pressure controller - - - -
A14.20.5.4 Filters - - - -
A14.20.5.5 Other system components - - - -
A14.20.6 Repair components - - - -
A14.20.7 Install components
A14.20.7.1 Outflow valve - - - -
A14.20.7.2 Pneumatic relay - - - -
A14.20.7.3 Auto pressure controller - - - -
A14.20.7.4 Filters - - - -
A14.20.7.5 Other system components - - - -
A14.20.8 Perform Pressure Decay Check * - - - -A14.20.9 Bench check components - - - -
A14.21 OXYGEN SYSTEM TR: AFOSH standards; TOs15X1-1, 42B5-1-2,42E1-1-1, Applicable KC-135TOs
A14.21.1 Operational fundamentals - - - -
A14.21.2 Operational check System * - - - -
A14.21.3 Troubleshoot System - - - -
A14.21.4 Inspect System Components * - - - -
A14.21.5 Purge system * - - - -
A14.21.6 Remove components
A14.21.6.1 Oxygen regulator * - - - -
A14.21.6.2 GOX Bottle - - - -
A14.21.6.3 Filler Valve - - - -
A14.21.6.4 Check Valve - - - -A14.21.6.5 Shutoff Valve - - - -
A14.21.6.6 Distribution Tubes/Hoses - - - -
A14.21.6.7 Indicator - - - -
A14.21.6.8 GOX Rack Assembly - - - -
A14.21.7 Install components
A14.21.7.1 Oxygen regulator * - - - -
A14.21.7.2 GOX Bottle - - - -
A14.21.7.3 Filler Valve - - - -
A14.21.7.4 Check Valve - - - -A14.21.7.5 Shutoff Valve - - - -
A14.21.7.6 Distribution Tubes/Hoses - - - -
KC-135 TRAINING REQUIREMENTSSTS 2A6X6, October 2002
247Attachment 14
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A14.21.7.7 Indicator - - - -
A14.21.7.8 GOX Rack Assembly - - - -
A14.21.8 Perform System leak check * - - - -
A14.21.9 Procedures for cleaning components - - - -
MH-53J TRAINING REQUIREMENTSSTS 2A6X6, October 2002
248Attachment 15
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
ATTACHMENT 15
NOTE 1: In addition to attachment 2, the tasks and knowledge in attachment 6 will be performed by personnel assigned to maintain MH-53J aircraft.
NOTE 2: Users are responsible for annotating training references to identify current references pending STS revision.
NOTE 3: Items marked in columns 2a or 2b marked with a (*R) are optional core tasks for ANG and AFRC.
NOTE 4: Address comments and recommended changes through the MAJCOM Functional Managers to the AETC Training Manager, DSN 736-2772
A15.1 AC POWER SYSTEM
TR: 1H-53(M)J-2-6
A15.1.1. Operational fundamentals - - - -
A15.1.2. Operational check * - - - -
A15.1.3. Troubleshoot System - - - -
A15.1.4. Remove components
A15.1.4.1. AC Generators - - - -
A15.1.4.2. VRSP - - - -
A15.1.5. Install components
A15.1.5.1. AC Generators - - - -
A15.1.5.2. VRSP - - - -
A15.1.6. Inspect System Components * - - - -
A15.2. DC POWER SYSTEMS
TR: 1H-53(M)J-2-6
A15.2.1. Operational Fundamentals - - - -
A15.2.2. Operational Check - - - -
A15.2.3. Troubleshoot System - - - -
A15.2.4. Remove components
A15.2.4.1. Transformer Rectifier Unit - - - -
A15.2.4.2. Battery Charger - - - -
A15.2.5. Install components
A15.2.5.1. Transformer Rectifier Unit - - - -
A15.2.5.2. Battery Charger - - - -
A15.2.6. Inspect System Components - - - -
A15.3. EXTERNAL POWER SYSTEM
TR: 1H-53(M)J-2-6
A15.3.1. Operational fundamentals - - - -
A15.3.2. Operational check * - - - -
A15.3.3. Troubleshoot System - - - -
A15.3.4. Remove components
A15.3.4.1. External Power Monitor Panel - - - -
A15.3.4.2. External power receptacle - - - -
A15.3.5. Install components
MH-53J TRAINING REQUIREMENTSSTS 2A6X6, October 2002
249Attachment 15
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A15.3.5.1. External Power Monitor Panel - - - -
A15.3.5.2. External power receptacle - - - -
A15.3.6. Inspect System Components * - - - -
A15.4. LIGHTING SYSTEMS
TR: 1H-53(M)J-2-6
A15.4.1. Operational Fundamentals
A15.4.1.1. Interior - - - -
A15.4.1.2. Exterior * - - - -
A15.4.1.3. Emergency - - - -
A15.4.2. Operational checks
A15.4.2.1. Interior - - - -
A15.4.2.2. Exterior * - - - -
A15.4.2.3. Emergency - - - -
A15.4.3. Troubleshoot
A15.4.3.1. Interior - - - -
A15.4.3.2. Exterior * - - - -
A15.4.3.3. Emergency - - - -
A15.4.4. Inspect System Components *
A15.4.4.1. Remove Components - - - -
A15.4.4.2. Emergency Exit Lights - - - -
A15.4.4.3. Heels Light Tube - - - -
A15.4.4.4. PMG control Box - - - -
A15.4.4.5. Heels Battery - - - -
A15.4.4.6. Controllable Spotlight Assembly - - - -
A15.4.4.7. Slime Lights (Formation Lights) - - - -
A15.4.4.8. Strobe light - - - -
A15.4.4.9. NVG Segment lights - - - -
A15.4.4.10. SX-5 Light Assembly - - - -
A15.4.4.11. Lighting Control panels - - - -
A15.4.4.12. Dimmer Control Panels - - - -
A15.4.5. Install components - - - -
A15.4.5.1. Emergency Exit Lights - - - -
A15.4.5.2. Heels Light Tube - - - -
A15.4.5.3. PMG control Box - - - -
A15.4.5.4. Heels Battery - - - -
A15.4.5.5. Controllable Spotlight Assembly - - - -
A15.4.5.6. Slime Lights (Formation Lights) - - - -
A15.4.5.7. Strobe light - - - -
MH-53J TRAINING REQUIREMENTSSTS 2A6X6, October 2002
250Attachment 15
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A15.4.5.8. NVG Segment lights - - - -
A15.4.5.9. SX-5 Light Assembly - - - -
A15.4.5.10. Lighting Control panels - - - -
A15.4.5.11. Dimmer Control Panels - - - -
A15.4.6. Repair System Component - - - -
A15.4.7. Bench Check Components - - - -
A15.5. LANDING GEAR SYSTEM
TR: 1H-53(M)J-2-1, 1H-53(M)J-2-6
A15.1. Operational Fundamentals
A15.1.1. Control - - - -
A15.1.2. Warning and indication - - - -
A15.2. Operational check
A15.2.1. Control - - - -
A15.2.2. Warning and indication - - - -
A15.3. Troubleshoot
A15.3.1. Control - - - -
A15.3.2. Warning and indication - - - -
A15.4. Inspect System Components - - - -
A15.5. Remove components
A15.5.1. Landing Gear Control Panel - - - -
A15.5.2. Indicator - - - -
A15.6. Install components
A15.6.1. Landing Gear Control Panel
A15.6.2. Indicator
A15.7. FIRE WARNING SYSTEM
TR: 1H-53(M)J-2-1
A15.7.1. Operational fundamentals
A15.7.1.1. Engine pylon - - - -
A15.7.1.2. Aux power plant (APP) and Heater - - - -
A15.7.2. Operational check
A15.7.2.1. Engine pylon - - - -
A15.7.2.2. Aux power plant (APP) and Heater - - - -
A15.7.3. Troubleshoot
A15.7.3.1. Engine pylon - - - -
A15.7.3.2. Aux power plant And Heater - - - -
A15.7.4. Inspect System Components
A15.7.4.1. Engine pylon - - - -
A15.7.4.2. Aux power plant (APP) - - - -
MH-53J TRAINING REQUIREMENTSSTS 2A6X6, October 2002
251Attachment 15
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A15.7.5. Remove components
A15.7.5.1. Detector - - - -
A15.7.5.2. Control Amps. - - - -
A15.7.5.3. Fire Warning Relay Assembly - - - -
A15.7.5.4. Fire Warning Control Panel - - - -
A15.7.6. Install components
A15.7.6.1. Detector - - - -
A15.7.6.2. Control Amps. - - - -
A15.7.6.3. Fire Warning Relay Assembly - - - -
A15.7.6.4. Fire Warning Control Panel - - - -
A15.7.7. Repair System Components
A15.7.8. Bench Check System Components - - - -
A15.8. FIRE EXTINGUISHING SYSTEM
TR: Applicable T.O.s
A15.8.1. Operational Fundamentals - - - -
A15.8.2. Operational Check
A15.8.2.1. Engine - - - -
A15.8.2.2. Aux Power Plant (APP) - - - -
A15.8.3. Troubleshoot
A15.8.3.1. Engine - - - -
A15.8.3.2. Aux power plant (APP) - - - -
A15.8.4. Remove components
A15.8.4.1. Engine Fire Bottle - - - -
A15.8.4.2. Aux power plant (APP) Fire Bottle - - - -
A15.8.4.3. Squib / cartridge * - - - -
A15.8.4.4. Emergency Control Panel - - - -
A15.8.5. Install components
A15.8.5.1. Engine Fire Bottle - - - -
A15.8.5.2. Aux power plant (APP) Fire Bottle - - - -
A15.8.5.3. Squib/ cartridge * - - - -
A15.8.5.4. Emergency Fire Control Panel - - - -
A15.8.6. Repair System Components - - - -
A15.8.7. Bench Check System Components - - - -
A15.9. MASTER CAUTION/WARNING SYSTEM
TR: 1H-53(M)J-2-6
A15.9.1. Operational fundamentals - - - -
A15.9.2. Operational check - - - -
A15.9.3. Troubleshoot System - - - -
MH-53J TRAINING REQUIREMENTSSTS 2A6X6, October 2002
252Attachment 15
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A15.9.4. Remove components
A15.9.4.1. Master Caution Panel - - - -
A15.9.4.2. Advisory Panel - - - -
A15.9.4.3. Master Caution Reset Light - - - -
A15.9.5. Install components
A15.9.5.1. Master Caution Panel - - - -
A15.9.5.2. Advisory Panel - - - -
A15.9.5.3. Master Caution Reset Light - - - -
A15.9.6. Inspect System Components - - - -
A15.9.7. Repair System Components - - - -
A15.9.8. Bench Check System Components - - - -
A15.10. FUEL SYSTEMS
TR: 1H-53(M)J-2-6
A15.10.1. Operational fundamentals
A15.10.1.1. In flight refueling (IFR) - - - -
A15.10.1.2. Ground Refuel and Transfer System - - - -
A15.10.1.3. Fuel Dump - - - -
A15.10.1.4. Aux Tank Jettison System - - - -
A15.10.2. Troubleshoot
A15.10.2.1. In flight Refueling (IFR) - - - -
A15.10.2.2. Ground Refuel and Transfer System - - - -
A15.10.2.3. Fuel Dump - - - -
A15.10.3. Remove components
A15.10.3.1. Refuel Control Panel - - - -
A15.10.3.2. Extend Harness - - - -
A15.10.3.3. Retract Harness - - - -
A15.10.3.4. Bleed Air Selector Valve - - - -
A15.10.3.5. Emergency Control Panel - - - -
A15.10.3.6. Dimming Control Unit - - - -
A15.10.4. Install components
A15.10.4.1. Refuel Control Panel - - - -
A15.10.4.2. Extend Harness - - - -
A15.10.4.3. Retract Harness - - - -
A15.10.4.4. Bleed Air Selector Valve - - - -
A15.10.4.5. Emergency Control Panel - - - -
A15.10.4.6. Dimming Control Unit - - - -
A15.10.5. Inspect System Components - - - -
A15.10.6. Repair System Components - - - -
MH-53J TRAINING REQUIREMENTSSTS 2A6X6, October 2002
253Attachment 15
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A15.10.7. Bench Check System Components - - - -
A15.11. START AND IGNITION SYSTEM
TR: 1H-53(M)J-2-6
A15.11.1. Operational fundamentals - - - -
A15.11.2. Operational check
A15.11.2.1. Jet engine System - - - -
A15.11.3. Troubleshoot System
A15.11.3.1. Jet engine system - - - -
A15.11.4. Remove components - - - -
A15.11.5. Install components - - - -
A15.11.6. Inspect System Components - - - -
A15.12. NESA ANTI-ICING SYSTEM
TR: 1H-53(M)J-2-6
A15.12.1. Operation Fundamentals - - - -
A15.12.2. Operational Check - - - -
A15.12.3. Troubleshoot System - - - -
A15.12.4. Remove components
A15.12.4.1. Control Panel - - - -
A15.12.4.2. Anti-ice Controller - - - -
A15.12.5. Install components
A15.12.5.1. Control Panel - - - -
A15.12.5.2. Anti-ice controller - - - -
A15.12.6. Inspect System Components - - - -
A15.12.7. Repair System Components - - - -
A15.12.8. Bench Check System Components - - - -
A15.13. WINDSHIELD WIPER SYSTEMS
TR: 1H-53(M)J-2-6
A15.13.1. Operational fundamentals - - - -
A15.13.2. Operational check - - - -
A15.13.3. Troubleshoot System - - - -
A15.14. AUXILIARY POWER PLANT (APP) SYSTEM
TR: 1H-53(M)J-2-2, 1H-53(M)J-2-6
A15.14.1. Operational Fundamentals - - - -
A15.14.2. Operational check - - - -
A15.14.3. Troubleshoot System - - - -
A15.14.4. Remove components
A15.14.4.1. APP control panel - - - -
A15.14.4.2. Volt Sensing Relay - - - -
MH-53J TRAINING REQUIREMENTSSTS 2A6X6, October 2002
254Attachment 15
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A15.14.4.3. Voltage Regulator - - - -
A15.14.5. Install components
A15.14.5.1. APP control panel - - - -
A15.14.5.2. Volt Sensing Relay - - - -
A15.14.5.3. Voltage Regulator - - - -
A15.14.6. Inspect System Components - - - -
A15.14.7. Repair System Components - - - -
A15.14.8. Bench Check System Components - - - -
A15.15. BLADE/PYLON FOLD SYSTEM
TR: 1H-53(M)J-2-4, 1H-53(M)J-2-6
A15.15.1. Operational Fundamentals - - - -
A15.15.2. Operational check - - - -
A15.15.3. Troubleshoot System - - - -
A15.15.4. Remove components
A15.15.4.1. Logic Unit - - - -
A15.15.4.2. Blade Fold Relay Panel - - - -
A15.15.4.3. Slip Ring - - - -
A15.15.4.4. Proximity Harness - - - -
A15.15.4.5. Tail Rotor Head Actuator - - - -
A15.15.4.6. Blade /Fold Control Panel - - - -
A15.15.4.7. Interrupt Panel - - - -
A15.15.4.8. Dimming Control Unit - - - -
A15.15.5. Install components
A15.15.5.1. Logic Unit - - - -
A15.15.5.2. Blade Fold Relay Panel - - - -
A15.15.5.3. Slip Ring - - - -
A15.15.5.4. Proximity Harness - - - -
A15.15.5.5. Tail Rotor Head Actuator - - - -
A15.15.5.6. Blade /Fold Control Panel - - - -
A15.15.5.7. Interrupt Panel - - - -
A15.15.5.8. Dimming Control Unit - - - -
A15.15.6. Inspect System Components - - - -
A15.15.7. Repair System Components - - - -
A15.15.8. Bench Check System Components - - - -
A15.16. COMBUSTION HEATER SYSTEM
TR: 1H-53(M)J-2-1, 1H-53(M)J-2-6
A15.16.1. Operational Fundamentals - - - -
A15.16.2. Operational check - - - -
MH-53J TRAINING REQUIREMENTSSTS 2A6X6, October 2002
255Attachment 15
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A15.16.3. Troubleshoot System - - - -
A15.16.4. Remove components
A15.16.4.1. Cabin Heater Control Panel - - - -
A15.16.4.2. Heater Relay Panel - - - -
A15.16.4.3. Heater Fuel Control - - - -
A15.16.4.4. Heater Can - - - -
A15.16.4.5. Pressure Switch - - - -
A15.16.4.6. Vent Blower - - - -
A15.16.4.7. Combustion Blower - - - -
A15.16.4.8. Ignition Unit - - - -
A15.16.5. Install components
A15.16.5.1. Cabin Heater Control Panel - - - -
A15.16.5.2. Heater Relay Panel - - - -
A15.16.5.3. Heater Fuel Control - - - -
A15.16.5.4. Heater Can - - - -
A15.16.5.5. Pressure Switch - - - -
A15.16.5.6. Vent Blower - - - -
A15.16.5.7. Combustion Blower - - - -
A15.16.5.8. Ignition Unit - - - -
A15.16.6. Inspect System Components - - - -
A15.16.7. Repair System Components - - - -
A15.16.8. Bench Check System Components - - - -
A15.16.9. Perform carbon monoxide check - - - -
A15.17. PARKING BRAKE SYSTEM
TR: 1H-53(M)J-2-4, 1H-53(M)J-2-6
A15.17.1. Operational Fundamentals - - - -
A15.17.2. Operational check - - - -
A15.17.3. Troubleshoot System - - - -
A15.17.4. Remove limit Switches - - - -
A15.17.5. Install Limit Switches - - - -
A15.17.6. Inspect System Components - - - -
A15.18. TAIL SKID SYSTEM
TR: 1H-53(M)J-2-6
A15.18.1. Operational Fundamentals - - - -
A15.18.2. Operational Check - - - -
A15.18.3. Troubleshoot System - - - -
A15.18.4. Remove Components
A15.18.4.1. Tail Skid Relay panel - - - -
MH-53J TRAINING REQUIREMENTSSTS 2A6X6, October 2002
256Attachment 15
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A15.18.4.2. Actuator - - - -
A15.18.5. Install components
A15.18.5.1. Tail Skid Relay panel - - - -
A15.18.5.2. Actuator - - - -
A15.18.6. Inspect System Components - - - -
A15.18.7. Repair System Components - - - -
A15.18.8. Bench Check System Components - - - -
A15.19. IN-FLIGHT BLADE INSPECTION SYSTEM
TR: 1H-53(M)J-2-1, 1H-53(M)J-2-6
A15.19.1. Operational Fundamentals - - - -
A15.19.2. Operational check - - - -
A15.19.3. Troubleshoot System - - - -
A15.19.4. Remove components
A15.19.4.1. Detector Assembly - - - -
A15.19.4.2. Signal Processor Assembly - - - -
A15.19.5. Install components
A15.19.5.1. Detector Assembly - - - -
A15.19.5.2. Signal Processor Assembly - - - -
A15.19.6. Inspect System Components - - - -
A15.19.7. Repair System Components - - - -
A15.19.8. Bench Check System Components - - - -
A15.20. ENGINE ANTI-ICE SYTEM
TR: 1H-53(M)J-2-2, 1H-53(M)J-2-6
A15.20.1. Operational Fundamentals - - - -
A15.20.2. Operational check - - - -
A15.20.3. Troubleshoot System - - - -
A15.20.4. Remove components
A15.20.4.1. Control Panel - - - -
A15.20.4.2. Solenoid Sensing Relay - - - -
A15.20.5. Install components
A15.20.5.1. Control Panel - - - -
A15.20.5.2. Solenoid Sensing Relay - - - -
A15.20.6. Inspect System Components - - - -
A15.20.7. Repair System Components - - - -
A15.20.8. Bench Check System Components - - - -
A15.21. ENGINE OVERSPEED SYSTEM
TR: 1H-53(M)J-2-2, 1H-53(M)J-2-6
A15.21.1. Operational fundamentals - - - -
MH-53J TRAINING REQUIREMENTSSTS 2A6X6, October 2002
257Attachment 15
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A15.21.2. Operational Check - - - -
A15.21.3. Troubleshoot System - - - -
A15.21.4. Remove Harness - - - -
A15.21.5. Install Harness - - - -
A15.21.6. Inspect System Components - - - -
A15.22. ENGINE OIL SYSTEM
TR: 1H-53(M)J-2-2, 1H –53(M)J-2-6
A15.22.1. Operational fundamentals - - - -
A15.22.2. Operational Check
A15.22.2.1. Oil Level System - - - -
A15.22.2.2. Oil Pressure System - - - -
A15.22.3. Troubleshoot System
A15.22.3.1. Oil Level System - - - -
A15.22.3.2. Oil Pressure System - - - -
A15.23. ENGINE AIR PARTICLE SEPERATOR (EAPS) SYSTEM
TR: 1H-53(M)J-2-1, 1H-53(M)J-2-6
A15.23.1. Operational Fundamentals - - - -
A15.23.2. Operational check - - - -
A15.23.3. Troubleshoot System - - - -
A15.23.4. Remove components
A15.23.4.1. Blower - - - -
A15.23.4.2. Actuator - - - -
A15.23.5. Install components
A15.23.5.1. Blower - - - -
A15.23.5.2. Actuator - - - -
A15.23.6. Inspect System Components - - - -
A15.23.7. Repair System Components - - - -
A15.23.8. Bench Check System Components - - - -
A15.24. ROTOR BRAKE SYSTEM
TR: 1H-53(M)J-2-4, 1H-53(M)J-2-6
A15.24.1. Operational Fundamentals - - - -
A15.24.2. Operational check * - - - -
A15.24.3. Troubleshoot System - - - -
A15.24.4. Remove Master Switch Control Panel - - - -
A15.24.5. Install Master Switch Control Panel - - - -
A15.24.6. Inspect System Components * - - - -
A15.24.7. Repair System Components - - - -
MH-53J TRAINING REQUIREMENTSSTS 2A6X6, October 2002
258Attachment 15
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A15.24.8. Bench Check Components - - - -
A15.25. CHIP DETECTOR SYSTEM
TR: 1H-53(M)J-2-4, 1H-53(M)J-2-6
A15.25.1. Operational Fundamentals - - - -
A15.25.2. Operational check * - - - -
A15.25.3. Troubleshoot System - - - -
A15.25.4. Remove components
A15.25.4.1. Relay Panel - - - -
A15.25.4.2. Chip Locator Panel Assembly - - - -
A15.25.4.3. Chip Detector Locator Panel - - - -
A15.25.4.4. Power Module - - - -
A15.25.5. Install components
A15.25.5.1. Relay Panel - - - -
A15.25.5.2. Chip Locator Panel Assembly - - - -
A15.25.5.3. Chip Detector Locator Panel - - - -
A15.25.5.4. Power Module - - - -
A15.25.6. Inspect System Components * - - - -
A15.25.7. Repair System Components - - - -
A15.25.8. Bench Check System Components - - - -
A15.26. HYDRAULIC PRESSURE WARNING SYSTEM
TR: 1H-53(M)J-2-4, 1H-53(M)J-2-6
A15.26.1. Operational Fundamentals - - - -
A15.26.2. Operational check - - - -
A15.26.3. Troubleshoot System - - - -
A15.26.4. Remove components
A15.26.4.1. Servo Fail Relay Panel - - - -
A15.26.4.2. Servo Fail Advisory Panel - - - -
A15.26.5. Install components
A15.26.5.1. Servo Fail Relay Panel - - - -
A15.26.5.2. Servo Fail Advisory Panel - - - -
A15.26.6 Inspect System Components - - - -
A15.26.7. Repair System Components - - - -
A15.26.8. Bench Check System Components - - - -
A15.27. RESCUE HOIST SYSTEM
TR: Applicable T.O.s
A15.27.1. Operational Fundamentals - - - -
A15.27.2. Operational Check - - - -
A15.27.3. Troubleshoot System - - - -
MH-53J TRAINING REQUIREMENTSSTS 2A6X6, October 2002
259Attachment 15
2. CoreTasks
3. Certification For OJT 4. Proficiency Codes Used To Indicate Training/Information Provided (See Attachment 1)
1. Tasks, Knowledge And Technical References A B C D E A3 Level
B5 Level
C7 Level
5 7 TngStart
TngComplete
TraineeInitials
TrainerInitials
CertifierInitials Course CDC
(1)Course
(2)CDC
A15.27.4. Inspect System Components - - - -
A15.28. VIBRATION MONITORING SYSTEM
TR: Applicable T.O.s
A15.28.1. Operational Fundamentals - - - -
A15.28.2. Operational Check - - - -
A15.28.3. Troubleshoot System - - - -
A15.28.4. Inspect System Components - - - -
CFETP 2A6X6 October 2002
260
SECTION B - COURSE OBJECTIVE LIST
4. Measurement. Each proficiency coded STS task or knowledge item taught at the technical school ismeasured through the use of an objective. An objective is a written instruction for the student so he or sheknows what is expected of them to successfully complete training on each task. Each objective is compressedof a condition, behavior, and standard which states what is expected of the student for each task. The conditionis the setting in which the training takes place (i.e. TOs, type of equipment, etc). The behavior is the observableportion of the objective (i.e. perform an operational check). The standard is the level of performance that ismeasured to ensure the STS proficiency code level is attained. Each objective uses letter codes(s) to identifyhow it is measured. All objectives use the PC code which indicates a progress check is used to measure subjector task knowledge. W indicates a comprehensive written test and is used to measure the subject or taskknowledge at the end of a block of instruction. PC/W indicates a subject or task knowledge progress check anda separate measurement of both knowledge and performance elements using a written test.
5. Standard. The standard of written examinations is 70% to 76%, depending on the number of questions onthe test. Standards for performance objectives are indicated in the objective and are also indicated on theindividual progress check checklist. The checklist is used by the instructor to document each student's progresson each task. Instructor assistance is provided as needed during the progress check, and students may berequired to repeat all or part of the behavior until satisfactory performance is attained. Students mustsatisfactorily complete al progress checks prior to taking the written test.
6. Proficiency Level. Review column 4A of the STS to determine the proficiency level of a particular task orknowledge item. Review the course objective list to determine which STS item the objective supports. Reviewthe proficiency code key in Part II, Section A of this CFETP for an explanation of the proficiency codes. Mosttask performance is taught to the ‘2b’ proficiency level which means the students can do most parts of the task,but does need assistance on the hardest parts of the task (partially proficient). The student can also determinestep-by-step procedures for doing the task
7. Course Objective List. A detailed listing of initial skills or craftsman course objectives may be obtained bysubmitting a written request to the school house Training Manager, 364 TRS/TRR, 511 9th Ave STE 1,Sheppard AFB TX, 76311-2338.
CFETP 2A6X6 October 2002
261
SECTION C - SUPPORT MATERIAL
8. The following list of support materials is not all-inclusive; however, it covers the most frequently referencedareas. For further information on the following courses, contact the OPR at:
333 TRS/TTCQS 782 TRG601 D Street 826 Avenue G Suite 4Keesler AFB, MS 39534-2229 Sheppard AFB, TX 76311-2867DSN 597-5893 DSN 736-2568
COURSE NUMBER COURSE TITLE DEVELOPER
*AFQTP 2EXXX-201L Workcenter Managers Handbook 333 TRS
*AFQTP 2EXXX-201LB C-E Managers Handbook 333 TRS
ECI Specialized Course 1200 Air Force Technical Orders 782 TRG
*AFQTP 2EXXX-201G Maintenance Support 333 TRS
*AFQTP 2EXXX-201P TMDE Management 333 TRS
*AFQTP 2EXXX-201J Maintenance Training Program 333 TRS*Courses can be downloaded from 333 TRS home page at: http://qflight.kee.aetc.af.mil
CFETP 2A6X6 October 2002
262
SECTION D - TRAINING COURSE INDEX
9. Purpose. This section of the CFETP identifies training courses available for the Electrical andEnvironmental Systems Specialty and shows how the courses are used by each MAJCOM in their career fieldtraining programs. For further information on the following courses, contact the OPR at:
364 TRS/TRR511 9th Ave STE 1Sheppard AFB, TX 76311-2338DSN 736-2772
10. Air Force In-Resident Courses.
COURSE NO. COURSE TITLE LOCATION USER
J3ABR2A636 008 Aircraft Electrical andEnvironmental Systems Apprentice
Sheppard AFB AF, FMS,ANGRC, AFRC
J3ACR2A676 000 Aircraft Electrical andEnvironmental Systems Craftsman
Sheppard AFB AF, ANGRC,AFRC
COURSE NO. COURSE TITLE LOCATION USER
J4AST2A6X6 061 Liquid Oxygen/Nitrogen StorageTanks
VariousLocations
AF, ANGRC,AFRC
11. Extension Course Institute (ECI) Courses.
364 TRS/TTMAS511 9th Ave STE 1Sheppard AFB, TX 76311-2338DSN 736-2772
COURSE NO. COURSE TITLE USER
CDC 2A656 Aircraft Electrical and Environmental Systems Journeyman AF
CDC 2A676 Aircraft Electrical and Environmental Systems Craftsman AF
CDC 2AX7X Aerospace Maintenance Craftsman AF
CFETP 2A6X6 October 2002
263
12. Exportable Courses.
For further information on the following exportable courses, contact the OPRs at:
367 TRSS 362 TRS6058 Aspen Ave 613 10th AveHill AFB, UT 84056-5805 Sheppard AFB, TX 76311-2352DSN 777-7830/8741 DSN 736-5206
The Hill AFB course catalog can be ordered from DSN 777-0160.
COURSE NO. COURSE TITLE OPR User
00TVT0000 FOD Prevention (VHS tape) 367 TRSS AF
00TVT0001 Safety and Radio Frequency (RF) Radiation(VHS tape)
367 TRSS AF
00TVT0001V1 Troubleshooting Techniques (ICW) 367 TRSS AF
00TTV0002 Aerospace Ground Equipment Training (ICW) 367 TRSS AF
00TCB0002V1 Multimeter Familiarization (ICW) 367 TRSS AF
00TIV0007 Potential Hazards of Oxygen EnrichedEnvironments (VHS tape)
367 TRSS AF
00CIV0008 Use and Care of Type III Torque Wrenches(ICW)
367 TRSS AF
00CVT0009 Torque Wrench, Use and Care (VHS tape) 367 TRSS AF
00TVT0011 Cold Weather Indoctrination (VHS tape) 367 TRSS AF
00CVT0012 Manual Acft Snow Removal (VHS tape) 367 TRSS AF
00TVT0017V1 General Aircraft Corrosion Control (VHS tape) 367 TRSS AF
00TIV1000 Aircraft Marshaling (ICW) 367 TRSS AF
01SIV8971V5.1.1 -86 Diesel Power Unit Operation (ICW) 367 TRSS AF
00SIV8972 MA-3D Air Conditioner Operation (ICW) 367 TRSS AF
00TVT0015 Installation of Aircraft Switch Guards 367 TRSS AF
01CIV0016 B-1B Emergency Ground Egress 367 TRSS AF
01CIV0051 B-1B Command Aircraft Systems Training(CAST) General Airplane Information
367 TRSS AF
01CIV0052 B-1B Hazardous Zones 367 TRSS AF
01CIV1001 B-1B Safe for Maintenance 367 TRSS AF
01CIV1615 B-1B Egress System Safety 367 TRSS AF
CFETP 2A6X6 October 2002
264
COURSE NO. COURSE TITLE OPR User
01JIV0001 B-1B General Electrical Maintenance, part 1 367 TRSS AF
01JIV0002 B-1B General Electrical Maintenance, part 2 367 TRSS AF
01JIV0003 B-1B General Electrical Maintenance, part 3 367 TRSS AF
01JIV0005 B-1B CITS Parameter Monitor Codes (PMC) 367 TRSS AF
01JIV0006 B-1B CITS Maintenance Codes 367 TRSS AF
01JIV0038 B-1B Hardness Critical Procedures (HCP)Check
367 TRSS AF
01JIV1100 B-1B Panel Types, Location, and Construction 367 TRSS AF
01JIV1101 B-1B Panel and Secondary Structure Inspection 367 TRSS AF
01JIV1103 B-1B Forward Equipment Bay (FEB) Panels 367 TRSS AF
01JIV1134 B-1B Fasteners/Related Hardware 367 TRSS AF
01JIV2301 B-1B CAST Aircraft Systems and Power Plant 367 TRSS AF
01JIV4300 B-1B EMUX 367 TRSS AF
01JIV5500 B-1B CAST CITS/EMUX 367 TRSS AF
01JIV5501 B-1B Ground Readiness Tests (GRT) 367 TRSS AF
01SIV1005 B-1B Proximity Switch (Cover/Uncover)Simulated Airborne Conditions
367 TRSS AF
01SIV2400 B-1B Auxiliary Power Unit Operation 367 TRSS AF
05IIV2401 C-5 Fire Warning and Overheat System 367 TRSS AF
05IIV3201 C-5 Anti-Skid Detection System 367 TRSS AF
05TIV1300 C-5 Landing Gear T/S and Maintenance 367 TRSS AF
05TIV1301 C-5 Landing Gear Rigging 367 TRSS AF
10CVT0001 KC-10 Emergency Ground Egress 367 TRSS AF
10TIV4600 KC-10 Air Refueling System T/S andMaintenance
367 TRSS AF
15AIV1301 F-15 Landing Gear T/S and Maintenance 367 TRSS AF
15AIV2400 F-15 Secondary Power T/S and Maintenance 367 TRSS AF
15AIV2401 F-15 Secondary Power System Advanced T/S 367 TRSS AF
15MIV23KC F-15E Engine Ignition System 367 TRSS AF
15TIV23K1 F-100 Engine Ignition System T/S 367 TRSS AF
CFETP 2A6X6 October 2002
265
COURSE NO. COURSE TITLE OPR User
16AIV1301 F-16 C/D Landing Gear System T/S andMaintenance
367 TRSS AF
16AIV1302 F-16 C/D Block 50 Landing Gear System T/Sand Maintenance
367 TRSS AF
16AIV1401 F-16 C/D Block 40 Advanced Flight ControlSystem T/S
367 TRSS AF
16AIV24A1 F-16 C/D Emergency Power Unit System T/Sand Maintenance
367 TRSS AF
16AIV24D0 F-16 C/D Engine Start System T/S 367 TRSS AF
16GIV1401 F-16 C/D Block 40 Digital Flight ControlSystem T/S
367 TRSS AF
16GIV2400 F-16 C/D Electrical System T/S andMaintenance
367 TRSS AF
16GIV2402 F-16 C/D Block 50 Electrical System T/S andMaintenance
367 TRSS AF
16GIV4101 F-16 C/D ECS T/S and Maintenance 367 TRSS AF
16TIV1402 F-16 C/D Block 50 Advanced Flight ControlSystem T/S
367 TRSS AF
16TIV1403 F-16 C/D Block 50 Digital Flight ControlSystem T/S
367 TRSS AF
16TIV24A2 F-16 C/D Block 50 Emergency Power UnitSystem T/S and Maintenance
367 TRSS AF
16TIV24D0 F-16 C/D Block 50 Engine Start System T/S 367 TRSS AF
16TIV3202 F-16 C/D Block 50 Anti-Skid and Brake SystemT/S
367 TRSS AF
16TIV4102 F-16 C/D Block 50 ECS T/S and Maintenance 367 TRSS AF
30TIT0001 C-130 Emergency Escape 367 TRSS AF
30TIV0001 C-130 Safe For Maintenance 367 TRSS AF
35CVT0001 C-135 Emergency Ground Egress Procedures 367 TRSS AF
35TIV4100 KC-135R Bleed Air 367 TRSS AF
35TIV4670 KC-135R Air Refueling System 367 TRSS AF
41TIV1410V1 C-141B Secondary Flight Controls System(Flaps and Spoilers)
367 TRSS AF
41UIV11B1 C-141 Cargo Doors and Ramp Operation 367 TRSS AF
52CVT0003 B-52H Emergency Ground Egress 367 TRSS AF
52TVT1202 B-52H Seat Safety 367 TRSS AF
J6AZU2E066 038 Air Force Technical Order (T.O.) System (Gen) 362 TRS AF
J6AZU2E066 039 Air Force Technical Order (T.O.) System (Gen)(Adv)
362 TRS AF
CFETP 2A6X6 October 2002
266
COURSE NO. COURSE TITLE OPR User
J6ANU00066 043 CAMS For Flightline and Backshop 362 TRS AF
CFETP 2A6X6 October 2002
267
13. Training Detachment (TD) Courses.
For further information on the TD courses, contact the OPRs at:
372 TRS 373 TRS912 I Ave Suite 3 912 I Ave Suite 4Sheppard AFB, TX 76311-2361 Sheppard AFB, TX 76311-2362DSN 736-4801 DSN 736-4679
COURSE NO.
J4AMF/ASF/AST:
COURSE TITLE OPR USER
2A6X6-001 Acft Elect Systems Spec (E-3) 373 TRS AF
2A6X6-004 A-10A Acft Elect Systems 372 TRS AF
2A6X6-005 C-5 Elect Systems Tech (Primary) 373 TRS AF
2A6X6-006 C-5 Elect Systems Technicians (Airframe Systems) 373 TRS AF
2A6X6-007 F-16 Tactical E & E System Technician (ElectricalOnly, C/D/Difference)
372 TRS AF
2A6X6-008 F-16 Tactical E & E System Technician(Environmental Only, C/D/Difference)
372 TRS AF
2A6X6-011 F-16 Tactical E & E System Technician (C/DEnvironmental Only)
372 TRS AF
2A6X6-012 F-16 Tactical E & E System Technician (C/DElectrical Only)
372 TRS AF
2A6X6-014 H-60 Elect Systems Technician (O Maint) 373 TRS AF
2A6X6-015 B-52 G/H Acft E & E Systems Craftsman 373 TRS AF
2A6X6-017 F-15 Tactical Acft E & E SystemsJourneyman/Craftsman (Electrics Only)
372 TRS AF
2A6X6-018 F-15 Acft E & E Systems Craftsman (ECS Only) 372 TRS AF
2A6X6-019 Acft Environmental Systems O Maintenance (E-3) 373 TRS AF
2A6X6-020 A-10A ECS 372 TRS AF
2A6X6-021 T-37 E & E Technician 372 TRS AF
2A6X6-022 T-38 E & E Systems Technician 372 TRS AF
2A6X6-024 T-1A E & E Systems 372 TRS AF
2A6X6-026 KC-135R E & E Technician 373 TRS AF
2A6X6-028 KC-10A E & E Systems Technician 373 TRS AF
CFETP 2A6X6 October 2002
268
COURSE NO.
J4AMF/ASF/AST:
COURSE TITLE OPR USER
2A6X6-031 U-2R Strategic E & E Systems 373 TRS AF
2A6X6-032 B-2 Acft Environmental Systems Craftsman 373 TRS AF
2A6X6-033 RC-135( ) E & E Technician 373 TRS AF
2A6X6-034 EC-135C/J E & E Technician 373 TRS AF
2A6X6-035 EC-130H Special Sys Air Conditioning System 373 TRS AF
2A6X6-036 H-53 Helicopter Electrical Repair Technician 373 TRS AF
2A6X6-037 C-141 Acft Electrical System Technician (OMaintenance)
373 TRS AF
2A6X6-038 C-141 Environmental Systems Technician 373 TRS AF
2A6X6-039 C-5 Environmental Systems Technician (Bleed AirAnd Oxygen System)
373 TRS AF
2A6X6-040 C-130B/E/H Electrical Systems Technician 373 TRS AF
2A6X6-041 C-130B/E/H Environmental Systems Technician 373 TRS AF
2A6X6-044 C-17A E&E System Technician 373 TRS AF
2A6X6-045 C-130 (SOF) E & E Systems Technician 373 TRS AF
2A6X6-046 KC-135 E & E Technician 373 TRS AF
2A6X6-052 C-5 Environmental System Technician (FireSuppression System)
373 TRS AF
2A6X6-058 B-1B E & E Systems Craftsman 373 TRS AF
2A6X6-059 F-15E Tactical Acft E&E System Maintenance(Electrics only)
372 TRS AF
2A6X6-060 F-15E Tactical Acft E&E System Maintenance(ECS only)
372 TRS AF
2A6X6-062 C-17A Flotation Deployment System (FEDS) 373 TRS AF
2A6X6-063 F-117A Acft E&E System Journeyman 372 TRS AF
2A6X6-064 B-2 Acft E&E System Craftsman 373 TRS AF
2A6X6-066 E-8C E&E Technician 373 TRS AF
2A6X6-067 C-5 Electrical System (Utility) 373 TRS AF
14. Courses Under Development/Revision. N/A
CFETP 2A6X6 October 2002
269
SECTION E - MAJCOM UNIQUE REQUIREMENTS.
15. MAJCOM Courses. Contact the course OPRs at:
HQ ACC LSG / OL-CA6058 AspenHill AFB, UT 84056-5805DSN 777-4278
COURSE NO. COURSE TITLE OPR USER
Y140009 ACC Production Superintendent HQACC/LSG
ACC
Y140015 ACC Maintenance Instructor HQACC/LSG
ACC
Y140020 ACC Maintenance Training Management HQACC/LSG
ACC