› wp-content › uploads › ... · Euphoria warrants any products purchased in the U.S.A. from...
Transcript of › wp-content › uploads › ... · Euphoria warrants any products purchased in the U.S.A. from...
LIMITED WARRANTY
Euphoria warrants any products purchased in the U.S.A. from an authorized Euphoria dealer. All products are warranted to be free from defects in material and workmanship under normal use and service for a period of two (2) years when the unit is installed by an authorized Euphoria dealer. Non-authorized dealer installed products carry a one (1) year parts and labor limit-ed warranty. This warranty applies to the original purchase only.
Euphoria will either repair or replace (as its option) any unit that had been found to be defective and under warranty provided the defect occurs within:
Two (2) years, if purchased through an authorized Euphoria dealer with original proof of purchase.
This limited warranty periods do not extend to units having been subjected to misuse, abuse, neglect, or accident. Products that in Euphoria’s judgment shows evidence of having been altered, modified, or serviced without Euphoria’s authorization, will be ineligible under this warranty.
To obtain warranty services please contact your retailer or visit our website at www.euphoriacaraudio.com for more details.
USER MANUALInstallation Instructions | Owners Manual
Due to continuous improvement of the product, specifications are subject to change without notice.www.euphoriacaraudio.com
F475 : F4100M750 : M1500 : M2250 : M2750
www.euphoriacaraudio.com
Low Impedance Stability
F475 - 2 Ohm Stereo (4 Channel)F4100 - 2 Ohm Stereo (4 Channel)M750 - 1 Ohm MonoM1500 - 1 Ohm MonoM2250 - 1 Ohm MonoM2750 - 1 Ohm Mono
Bass Boost
The DB Drive Euphoria Mono amplifiers feature a variable Bass Boost gain centered at 45Hz thatenables the user to adjust the amount of bass boost needed to achieve the desired amount of lowend response from the subwoofer system.
The DB Drive Euphoria 4 channel amplifiers (F475 & F4100) feature a variable 12dB slope High Pass crossover for channels 1 and 2. Channels 3 and 4 feature a selectable 3 way 12dB Variable crossover that enable the user to select High Pass, Band Pass or Low Pass settings.
M750, M1500, M2250 and M2750
M750 - M1500 - M2250 - M2750
F475 - F4100 (M750 – M1500 – M2250 – M2750)
( Mono: M750, M1500, M2250, M2750)( 4 Channel: F475, F4100 )
The M750, M1500, M2250 and M2750 are equipped with a variable 24db slope Lowpass crossover network and a 24db slope subsonic lter. The mono amps also feature a variable Bass Boost EQ is set at 45Hz.
In some subwoofer enclosure installations it may necessary to use the Phase Shift feature. The Phase Shift button sets the Subwoofer signal between 0 degree setting and 180 degree settings. This will also allow you to ne tune the subwoofer enclosure depending on vehicle location.
The DB Drive Euphoria 4 channel ampliers (F475 and F4100) feature a 12db Slope crossover network. Channels 1 and 2 can be used in the High pass setting or full range and channels 3 and 4 feature a selectable 3 way crossover system that can be used in High pass, Bandpass or low pass settings.
Adjustments and SettingsThe F475 and F4100 ampliers are equipped with a variable crossover network that allows you to select the crossover mode (Highpass—Full Range) and desired crossover point for channels 1 and 2. With a High Pass range between 50Hz and 4 KHz, channels 1 and 2 can be used with a component tweeter or any type of full range speaker requiring High Pass ltering. Channels 3 and 4 allow you to select between a 3 way completely variable High pass Bandpass or Low pass setting that can be congured in many dierent ways allowing the user set up the perfect audio system.
For example if you wish to drive a pair of subwoofers on channels 3 and 4 in the bridged mode, you can select the LP switch settings on the amplier to lter out the high frequencies. You will then need to adjust the Lowpass control to the desired frequency setting. This will only send low frequencies to your subwoofers. If you wish to use the Bandpass crossover lter you must set the x-over push button switch settings to BP. Once the BP switch setting is selected you will use both the Lowpass and Highpass controls to lter out the unwanted low and high frequencies to create the desired Bandpass lter. (The Bandpass crossover is available on only channels 3 and 4) To use the Highpass lter select the x-over push button switches to the HP setting, this will lter out any unwanted low frequencies.
Built-in Crossover
12
Dimensions
F475F4100M750M1500M2250M2750
Height
2.28" / 58mm
2.28" / 58mm2.28" / 58mm
Width
7" / 178mm
7" / 178mm7" / 178mm
7" / 178mm
Length
10" / 254mm2.28" / 58mm2.28" / 58mm
7" / 178mm10.8" / 274mm7.6"/ 193mm9.2" / 234mm10.8" / 274mm
2.28" / 58mm 7" / 178mm13" / 330mm
Power (RMS) @ 14.4 VDC , THD .04% 4Ω:Power (RMS) @ 14.4 VDC , THD 1% 2Ω:
Power (RMS) @ 14.4 VDC , THD 1% 4Ω Bridgeable:Power Supply Input Voltage:
THD (1kHz @ 4Ω):Bandwidth (-3 dB):
Damping Factor (1kHz @ 4Ω):S/N Ratio (as weighted @ 1 Volt):
Input Sensitivity:Minimum Load Impedance:
Input:Channel 1-2 Filter Slope:
Channel 1-2 Filter Range:
Channel 3-4 Filter Slope:Channel 3-4 Filter Range:0Hz)
4 x 75W4 x 95W2 x 300W11VDC to 15VDC0.04%18Hz - 22KHz10099db.20MV - 7.0V RMS2ΩPre In RCA12dB(FR = Un-filtered)(HP = 50Hz - 4KHz)HP @ 12db St. , LP/BP @ 12dB St.(HP = 50Hz ~ 4KHz) (BP = 32Hz ~ 4KHz)(LP = 32Hz ~ 250Hz)
Power (RMS) @ 14.4 VDC , THD .04% 1Ω:Power (RMS) @ 14.4 VDC , THD 1% 2Ω:
Power Supply Input Voltage:THD (1kHz @ 4Ω):
Bandwidth (-3 dB):Damping Factor (1kHz @ 4Ω):
S/N Ratio (as weighted @ 1 Volt):Input Sensitivity:
Minimum Load Impedance:Input:
Output:Mono Low Pass Filter Slope:
Low Pass Filter Range:Sub-sonic Filter Slope:
Sub-sonic Filter Range:Bass Boost @45Hz:
1 x 750W1 x 325W11VDC to 15VDC0.04%10Hz - 220Hz12699db.20MV - 7.0V RMS1ΩPre In RCAPre out RCA Full Range12dB40Hz ~ 200Hz12dB10Hz ~ 40Hz0 ~ 12db
Power (RMS) @ 14.4 VDC , THD .04% 1Ω:Power (RMS) @ 14.4 VDC , THD 1% 2Ω:
Power Supply Input Voltage:THD (1kHz @ 4Ω):
Bandwidth (-3 dB):Damping Factor (1kHz @ 4Ω):
S/N Ratio (as weighted @ 1 Volt):Input Sensitivity:
Minimum Load Impedance:Input:
Output:Mono Low Pass Filter Slope:
Low Pass Filter Range:Sub-sonic Filter Slope:
Sub-sonic Filter Range:Bass Boost @45Hz:
1 x 2250W1 x 1125W11VDC to 15VDC0.04%10Hz - 220Hz12699db.20MV - 7.0V RMS1ΩPre In RCAPre out RCA Full Range12dB40Hz ~ 200Hz12dB10Hz ~ 40Hz0 ~ 12db
4 x 100W4 x 150W2 x 400 W11VDC to 15VDC0.04%18Hz - 22KHz10099db.20MV - 7.0V RMS2ΩPre In RCA12dB(FR = Un-filtered)(HP = 50Hz - 4KHz)HP @ 12db St. , LP/BP @ 12dB St.(HP = 50Hz ~ 4KHz) (BP = 32Hz ~ 4KHz)(LP = 32Hz ~ 250Hz)
1 x 1500W1 x 750W11VDC to 15VDC0.04%10Hz - 220Hz12699db.20MV - 7.0V RMS1ΩPre In RCAPre out RCA Full Range12dB40Hz ~ 200Hz12dB10Hz ~ 40Hz0 ~ 12db
1 x 2750W1 x 1375W11VDC to 15VDC0.04%10Hz - 220Hz12699db.20MV - 7.0V RMS1ΩPre In RCAPre out RCA Full Range12dB40Hz ~ 200Hz12dB10Hz ~ 40Hz0 ~ 12db
M2250 M2750
M1500
F4100F475
M750
PROBLEM LOOK FOR SOLUTION
No Output Blown fuse Replace Bad RCA Cable(s) Replace +12V at power terminal Check connection +12V at remote terminal Check connection Grounding point are clean and tight Check for ground w/meter Head unit’s fader not in center position Set to center position Master and slave settings Confirm correct setting
Low Output Check level adjustments
Re-adjust Bad RCA cable(s) Replace Improper level matching Re-adjust Master and slave settings Confirm correct settings
Engine Noise Grounding points are clean and tight Check for ground w/meter Ground all components at same point Ground at same point Try different grounding point Change for better ground Bad RCA cable(s) Replace Use high quality shielded RCA cables Rejects inducted noise Low vehicle charging system and/or battery Fix and/or replace Red protection L.E.D. illumintaed Speaker short Check speakers connection for short circuit Speaker grounding out Make sure speaker wires do not touch chassis ground Impedance too low Check speaker impedance Overheating Check mounting location for adequate air circulation. Speaker impedance too low