hawkinsgraves.com 622-16-10 10 RIDE-ON TROWELS HD & HDX SERIES HYDRA-DRIVE SERIES All-Hydraulic...

HAWKINS-GRAVES

EST.

1966

CAT

C

13432 Wards RoadLynchburg, VA 245011-866-847-7703Fax: 434-847-7707www.hawkinsgraves.com

Hawkins-Graves13432 Wards Road • Lynchburg, VA 24501

1-866-847-7703www.hawkinsgraves.com

N

E

S

W

29��

��460

Lynchburg Rgn./Preston Glenn Fld.

29��

Wards

Rd.

��460

Lees

ville

Rd.

Co Rd. 738

Pine Lake

Airport Rd.

Airp

ortR

d.

CoRd

. 224

Wards

Rd.

Co Rd. 579

Ride-On TrowelsWalk-Behind Trowels

Concrete Screeds

Concrete PumpsTrowel Blades

Float PansConcrete Saws

Concrete BladesMasonry Saws

ScarifiersGrinders/ Accessories

Mortar MixersHoists

Concrete Vibrators / AccessoriesConcrete Buckets / Accessories

Masonry EquipmentMasonry Hand Tools

Concrete Finishing Tools

9

Concrete & Masonry 1

MP305

622-

16-1

0

10

RIDE-ON TROWELS

HD & HDX SERIES HYDRA-DRIVE SERIESAll-Hydraulic riders are the largest, most powerful and most reliable available.

MSP SERIESMECHANICAL-DRIVE SUPER PRO SERIESRiders are available in either hydraulic power or manual lever steering with both diesel and gasoline engine options.

MP SERIESMECHANICAL-DRIVE PRO SERIES Riders deliver value and versatility with manual lever steering and range of gasoline engine options.

MODEL HD560 HDX600Engine Turbo Charged Kubota Diesel 99 HP 44 HP Dimensions (L x W x H) 144" x 66" x 64" 108.5" x 50.5" x 56"Panning Path Width 139" 100"Rotors (Diameter) 60" 6-Bladed Spider 46.5" 5-Bladed SpiderMaximum Rotor Speed 135 RPM 135 RPMWeight 3,055 Lbs. 1,613 Lbs.Fuel Capacity 20 Gal. 11 Gal.

MODEL MSP460 MSP425 MSP415Engine 44 HP 34 HP 35 HP Vanguard Air-Cooled Gas

Turbo Charged Kubota Diesel Vanguard Liquid-Cooled Gas Vanguard Air-Cooled GasDimensions (L x W x H) 101.5" x 50.5" x 59.5" 100" x 50" x 57" 101.5" x 50.5" x 58" Panning Path Width 95" 95" 97.5"Rotors (Diameter) 46" 5-Bladed Spider 46" 5-Bladed Spider 46" 5-Bladed SpiderMaximum Rotor Speed 140 RPM 165 RPM 145 RPMWeight 1,450 Lbs. 1,132 Lbs. 1,047 Lbs.Steering Power Power ManualCruise Control Yes No NoFuel/Retardant Capacity 6 Gal. 6 Gal. 6 Gal.

MODEL MP305 MP205 MP225 EDGEREngine 24 or 27 HP 20, 24 or 27 HP 24 or 27 HP

Kohler Air-Cooled Gas Kohler Air-Cooled Gas Kohler Air-Cooled GasDimensions (L x W x H) 100" x 50" x 55" 84" x 41" x 55" 88" x 40" x 54" Panning Path Width 96" 74" 85"Rotors (Diameter) 46" 4-Bladed Spider 36" 4-Bladed Spider 36" 4-Bladed SpiderMaximum Rotor Speed 110-122 RPM 125-145 RPM 120-145 RPM Application Finishing and Light Duty Panning Finishing and Panning Edging, Finishing and PanningWeight Depending on Engine 819-826 Lbs. 702-744 Lbs. 762 Lbs. Fuel/Retardant Capacity 6 Gal. 6 Gal. 6 Gal.

HDX600

HD560

MP205

MSP460

622-

17-1

0

11

WALK-BEHIND TROWELS / BLADES / PANS

MODEL PRO446SHD PRO 446SD PRO 446 PRO & ECONOMY 436 PRO 436 EDGER PR 430 EDGEREngine: Honda or Subaru 13 HP 11 HP 9 or 11 HP 5.5, 6 or 9 HP 5.5 or 9 HP 5.5 HPDimensions (L x H) 89" x 39" 89" x 39" 89" x 39" 70" x 38" 84" x 38" 60" x 36"Rotor Diameter 46" 5-Blades 46" 4-Blades 46" 4-Blades 36" 4-Blades 36" 4-Blades 30" 4-BladesMaximum Rotor Speed 118 RPM 118 RPM 118 RPM 118 RPM 118 RPM 118 RPMWeight 390 Lbs. 233-285 Lbs. 252-273 Lbs. 186-222 Lbs. 196 Lbs. 223 Lbs. Trowel Arms and Spider Super Duty Super Duty Standard Duty Standard Duty or Standard Duty Standard Duty

(SHD Gearbox) Economy Gear Boxand Standard Duty Spider

COMPODISK®

Exclusive – and patented – Compodisk® is a new and exciting composite pan acoustically matched to the concrete to be processed. The Compodisk has acoustic impedance which matches the concrete, thereby imparting its energy into the concrete mass. This causes the concrete to set from the bottom of the slab to the top while maintaining an open surface, allowing the bleed water to escape during the finishing process. This new technology of floating disk is made from a composite material and is only available by Allen.

PANS / BLADESA complete line of finish blades, combination blades and clip-on float shoes for your walk-behind or ride-onpower trowel. We use high quality steel and high strengthrivets to maximize blade life. Premium finishing blades are manufactured to high tolerances to provide the highest F-Numbers possible. For the flattest floors, trust only Allen® Finishing Blades.Allen Engineering pioneered the use of floating discs (orpans) on riding trowels in 1989 and Allen® Pans remaintoday the finisher’s choice when high F-Numbers are spec-ified on a concrete floor. Allen’s flat pan tolerances cutbumps and fill low spots in the concrete floor.

WALK-BEHIND TROWELS

Economy 436 Pro 436 430 Edger

1. Fingertip throttle control.2. Safety switch.3. Stabilizer ring (on 446 Series).4. Wide range of engine options.5. Cast iron spiders,

pressure plates and lift levers are built to provide years of trouble-free service.

PRO SERIES STANDARD FEATURES6. Lifting bar.7. Lifting hook.8. Padded handle.9. Height adjustable handle.

1

622-

18-1

0

12

SCREEDS

Precision engineered, lightweight wet screed for single operator fast strike-off of concrete. Fast and easy to use, this high-frequency screed provides uniform distribution over the entire blade length, enhancing structural integrity of the concrete through consolidation.

MODEL HD7070Engine 4-Stroke, 1.5 HP, 35 ccHandles AdjustableWeight 30 Lbs.

MAGIC SCREED®

MODEL 12HD 12HED 12ECSFrame Construction Steel Steel AluminumVibration System Dual Air Eccentric Shaft Eccentric ShaftSection Lengths/Weights2 Ft: 37 Lbs. 37 Lbs. 24 Lbs.2.5 Ft: 47 Lbs. 46 Lbs. 34 Lbs.5 Ft: 93 Lbs. 90 Lbs. 60 Lbs.7.5 Ft: 138 Lbs. 135 Lbs. 90 Lbs.10 Ft: 186 Lbs. 180 Lbs. N/AMaximum Width 65 Ft. 65 Ft. 50 Ft.Blades - Galvanized Steel 10 Gauge 10 Gauge 12 Gauge

Air Vibration ScreedsOur air-driven screeds feature precision engi-neered naval bronze piston vibrators that arerust resistant, non-sticking and free-starting.

Engine-Driven ScreedsWith engine options ranging from 5.5 HP to 11 HP, there’s a steel screed for virtually everysize floor finishing operation.

1. Quick disconnect system.2. Replaceable greaseable bearings.3. Eccentric vibrator weights.4. Wide range of engine options.5. Triangular frame with vibration

proof welds.

6. Manual winch is standard.7. Bolt-on replaceable blades. 8. Low profile engine option (steel screed

only). Straddle mount engine standard on aluminum truss screed.

9. Convertible to air vibration version.10. Hydraulic winch option.

Bridge Deck FinishersOur Bridge Deck Finishers are quickly becoming the choice for high-volume bridge pours. Two models are available with many accessories,so there’s an Allen Paver for every bridge pour, and built to the highest tolerances for any jobs.

MODEL 4836B 6048B Console engine 25 Hp Kohler® 25 Hp Kohler®

air-cooled gas Paving carriage engine 25 Hp Kohler® 25 Hp Kohler®

air-cooled gasPaving rollers dual 48" (1219mm) 60" (1523mm) Augers dual adjustable 8" (203mm) 8" (203mm)Section widths available 3', 4', 6', 12', 15' 3', 4', 6', 12', 15'

(1, 1.2, 1.8, 3.7, 4.6m) (1, 1.2, 1.8, 3.7, 4.6m)Bogies-driver w/cupped wheels Two 36" (914mm) Two 48" (1219mm) Bogies-idler w/cupped wheels Two 36" (914mm) Two 48" (1219mm) Legs (w/solid leg plates) 4" (101mm) 6" (152 mm)

44" (1118mm) 44" (1118mm)vertical adj. vertical adj.

12HED Steel Screed

1. Quick-change screed blade.2. Anti-vibrating system.3. Carrying bars.4. Ergonomically designed grips.5. Smooth operating throttle.6. Lightweight but powerful engine.7. Tilt-up stand.

AVAILABE WIDTHS AND WEIGHTS (NO ENGINE):4 ft. 6 lbs., 6 ft. 10 lbs., 8 ft. 13 lbs., 10 ft. 16 lbs., 12 ft. 20 lbs., 14 ft. 23 lbs.

622-

19-1

0

13

ROLLER TUBES

MODEL 255CD 200C 150BEngine 44 HP Kubota® Diesel 34 HP Vanguard® Gasoline 27 HP GasolineWidths Available (2 ft. increments) 12-34 Ft. 12-32 Ft. 12-32 Ft.Weight at 22 Ft. 5,570 Lbs. 3,835 Lbs. 2,790 Lbs.Roller Tube Diameter 10" 8-5/8" 6-5/8"Tube Weight per Ft. 27 Lbs. 29 Lbs. 19 Lbs.Hydraulic Oil Reservoir 25 Gal. 13.5 Gal. 13.5 Gal.Hydraulic Spray System Standard Optional OptionalHydraulic Steering Leg Standard Standard Optional

HYDRAULIC DRIVE RTF• Drive unit features a Webster control valve.• 13.5 HP Subaru engine with electric start.• 4.5 GPM hydraulic system at 25000 PSI.• 50-foot Quick Disconnect Hose is standard.• Removable frame for maintenance.• Hydraulic cooling system with 12-volt fan.

Precision engineered tubes ensure the smoothest pavement possible. Powered by rugged gasoline or diesel engines, with easy-to-operate control systems, the Triple Roller Tube Paver can strike off concrete fast. And with our precision engineered and level-tested roller tubes,you can be assured of producing the flattest paving job possible. Three models available or customizable to your specifications.

ENGINE DRIVE ENGINEEngine 2.5 HP 4-cycle Honda

HYDRAULIC DRIVE HYDRAULICEngine 13.5hp Air-Cooled

AVAILABLE WIDTHS WEIGHT (tube)

6 Ft. 53 Lbs.8 Ft. 66 Lbs.10 Ft. 78 Lbs.12 Ft. 90 Lbs.14 Ft. 103 Lbs.16 Ft. 117 Lbs.18 Ft. 131 Lbs.20 Ft. 145 Lbs.22 Ft. 158 Lbs.24 Ft. 172 Lbs.26 Ft. 186 Lbs.

ROLLER TUBE FINISHERS

TRIPLE ROLLER TUBE PAVERS

ENGINE DRIVE RTF• 2.5 HP, 4-cycle Honda® Engine.• 18:1 gear ratio transmission.• Automatic centrifugal clutch.• Right angle drive gear box.• Wheel assembly.• Power unit storage box.

150B

255CD

1

622-

20-1

0

14

SPRAYERS / VIBRATORS

MODEL ELECTRIC GASOLINEEngine 115 Volt Grounded 4-cycleVibrations per Minute 11,000-12,000 11,000-12,000Flexible Shaft lengths 2-21 Ft. 2-21 Ft.Vibrator Heads Steel and Rubber Steel and Rubber

Powerful, reliable and durable sprayers are the preferred tool forapplying release agents and water-based sealants and curing compounds on concrete construction sites. The continuous recirculating system ensures your material is always well mixed and ready to spray. Available in barrel, cart or tow.

SPRAYERS

FLEX-SHAFT AND BACKPACK VIBRATORS

MODEL 9910 7560XLEngine 5.5 HP Gasoline Engine 4 HP Gasoline EngineMaximum Flow Rate 9.5 Gallons per Minute 7.5 Gallons per MinutePump Type Diaphragm Roller BallHose Type Hydraulic 3/8" Lock-OnWeight 134 Lbs. 106 Lbs.

• All materials must be thoroughly mixed before spraying.• Sprayers are intended for spraying Form Release Agents,

Water-based Sealants and Concrete Curing Compounds.• Allen sprayers are not intended for spraying any types of

asphalt sealants. Spraying of any type of asphalt sealers willcause damage to pump and will not be covered by warranty.

Available in electric or gasoline powered backpack models, these vibrators provide superior consolidationof concrete and feature interchangeable heads andshafts with our quick disconnect system.

Electric: Lightweight model features high VPM in an easy-to-carry size.Includes shoulder strap.

Gasoline: Go anywhere backpack version features“speed-up” transmission, allowing engine to run atlow RPM’s and still produce high VPM’s.

7560XL

Barrel mountconfigurationis standard.

Barrels notincluded.

9910Spray gun fan tip 4020 and50' (7.6m) of hose are standard on sprayers.

1930

-43-

10

RIDE-ON TROWELS

JWN24HTCSL

HHN31VTCSL5

STX55Y6

HYDROSTATIC RIDE-ON TROWEL

Model EngineEngineCooling HP

Bladesper

RotorRotorRPM

PathWidth

In. (cm)

Fuel TankCapacitygal. (ltr.)

Run Timegal./hr.(ltr./hr.)

L x W x Hin. (cm)

OperatingWeight

lbs. (kg) Wheel Kit

Hydrostatic SeriesTwin 60" Non-OverlappingSTX55Y6

YanmarTurbo Diesel

Liquid 60 6 10-130 117(297)

11(42)

2.81(10.93)

125 x 65 x 57(318 x 165 x 57)

2270(1030)

EMR3

Mechanical SeriesTwin 48" Non-OverlappingHHN31VTCSL5

Vanguard Liquid 31 5 40-160 91 (231)

4.4(17)

2.51(9.5)

95 x 48 x 46(241 x 122 x 117)

1120(508)

EMR2 orEMR3*

Twin 46" OverlappingHTO31VTCSL5

Vanguard Liquid 31 5 145 88(223.5)

5(19)

2.4 93 x 50 x 46(236 x 127 x 117)

1052(447.1)

Twin 36" Non-OverlappingJWN24HTCSL

Honda Air 20 4 36-180 75(191)

2.2(8)

1.71(6/47)

77 x 39 x 48(196 x 99 x 122)

685(209)

EMR2

*For current production units only. May not adapt to older models.

MECHANICAL RIDE-ON TROWELSHHN31VTCSL5Non Overlapping twin 48" 31-hp Vanguard gas

• Five blades per rotor, 91-inch path width.• A 31-hp Vanguard 3 Cyl liquid cooled gasoline engine. • Variable speed clutch. • Helical gearbox operates at 98% efficiency. • Twin-pitch control for simultaneous pitch control.

JWN24HTCSLNon-Overlapping twin 36" GX670 Honda

• Smooth responsive patented steering assist makes thisunit easy to control on any slab.

• Twin 36-inch non-overlapping rotors great for all stagesof finishing from panning to sealing.

• Equipped with a GX670 Honda V-Twin gasoline engineand construction grade driveline that enables rotor speedranges from 36-170 rpm.

HTO31VTCSL5Overlapping twin 46" 31-hp Vanguard

• Powerful 31-hp Vanguard 3-cylinder liquid-cooled gasoline engine meets the needs of the professional concrete contractor.

• Twin-overlapping rotors cover a path width of 88 inches wide using 5-blades per rotor.

• Heavy-duty worm-drive gearbox with large oil capacities and integral cooling fans to reduce heat buildup.

• Whiteman’s patented TwinPitch control and steeringassist come standard.

STX55Y6Non-overlapping twin 60" 60-HP Yanmar Turbo Diesel

• Hydraulic trowel eliminates gearboxes, clutches • Reliable, trouble-free design. • Path width of 117 inches. • Powered by a 60-hp Yanmar turbo diesel engine. • Six blades per rotor. • Rotor speeds up to 130 rpm.

1

15

WALK-BEHIND TROWELS

1930

-42-

10

TROWELS

C-Series

B-Series

J-Series HD-Series

Model HP (kw)* Motor Clutch RPM Operating Weight

lb. (kg)Handle Options

(see side)C-Series - 24-inch Rotating Guard RingCA4HC 3.5 (2.6) Honda Centrifugal 70-130 125 (57) STHAC; QPHAFC

J-Series - 36-inch Guard RingJ36H55 4.8 (3.6) Honda Centrifugal 60-115 150 (68) SXH; QXHB-Series - 46-inch Guard RingB46H90 8 (6.0) Honda Centrifugal 60-130 242 (110) SXH; QXH

HD Series - 48-inch Guard Ring

HDA48413H 11.1 (8.2) Honda Variable Speed 35-180 315 (143) SXHHD; QXHHD

Trowel Handle OptionsSTHAC – Standard knob

style pitch control forCA4HC (centrifugal clutch) model

QPHAFC – Folding Quick-Pitch control for CA4HC(centrifugal clutch) model

SXH – Standard knob stylepitch control for M-, J- and B-Series trowels

QXH – Quick-Pitch style control for M-, J- and B-Series trowels

SXHHD – Standard knobstyle pitch control for HD-Series trowelswith 2-inch diameter handle mount

QXHHD – Quick-Pitch stylecontrol for HD-Seriestrowels with 2-inch diameter handle mount

Improves productivity in confi ned areas or whenworking against walls, pipes and slab edges.

The C-Series trowel features a rotating guard ring to reducemanual labor while edging. It enables the operator to finishwithin #/16" of obstructions. The high capacity gearbox delivers big machine performance in a small package.

The J-Series incorporates amazing balance, improved serviceability, and your choice of a Standard or Quick-PitchHandle, providing contractors with the ideal machinefor residential and general construction work.

The favorite trowel of the construction industry.

These 46" (1170 mm) workhorses will handle the majority ofyour fi nishing requirements. The B-Series incorporates all ofour latest improvements, amazing balance and control, andimproved serviceability.

The HD48 is designed for jobs that require high speed burnishing — up to 180 RPM; with our HD gearbox andComet CVT Drive system this trowel can fi nish a slab surface rapidly under any condition.

16

1930

-41-

10

CONCRETE PUMPS

C30HD Small Line • Powerful engines – 68 HP Zenith gasoline or

32-HP Deutz diesel engines.Smoothest runningengines in the industry.

• Heavy-duty centrifugal clutch– for longer life

• Central lubrication system – enclosed lubrication box provides clean, positive piston lubrication.

• Remote controls – hardwired 125 ft. cable or an optional wireless remote control.

• All steel engine cover (hood) – rugged designresists abuse.

• Three-speed volume control – enables theoperator to control the flow.

• E-Z Open™ Manifold – hinged for quick accessto seats, cylinders and piston cups. Easy openreducer.

• Longer frame with fuel cell inside frame.• Full featured highway

light package.• Standard with each C30HD: Elbow – with

heavy-duty raised ends; 3" x 2" Reducer –with heavy-duty raised ends; Two 3" adjstablesnap couplings.

• Control box features engine hour meter, temperature warning light, battery warning light.

LS400 / LS500 Mid Range • Remixer/agitator hopper – standard.• Engine Cover (hood) – standard.• Versatility – handles low cement/sand mixes up

to 1-1/2" aggregate.• Easily removed hopper for quick maintenance.• Infinite volume control. • Extra heavy-duty main frame. • Solid state Digital Control Panel. • Reverse pumping for instant response and

smoother operation.• Hydraulic surge brakes.• Exclusive full-flow shuttle-tube concrete valve

– more efficient operation.• One-man operation – simple controls.

Options:• Wireless remote control.• Air or electric vibrators for hopper screen.• Hydraulic rear outriggers.

LS600 • Concrete piston face pressure –

1100 psi (69 bar).• Engine Cover (hood) – standard.• Versatility – handles low cement/sand mixes up

to 1-1/2" aggregate.• Remixer/agitator hopper – standard.• Easily removed hopper for quick maintenance.• Infinitely variable volume control – from 0

to 60 cubic yards per hour.• Heavy-duty Deutz 99 HP diesel engine.• True reverse pumping for instant response

and smoother operation.• Solid state Digital Control Panel. • Exclusive full-flow shuttle-tube concrete valve

– more efficient operation.• One-man operation – simple controls.

Options:• Wireless remote control.• Air or electric vibrators for hopper screen.• Hydraulic rear outriggers.

MODEL C30HD LS400 LS500 LS600PERFORMANCE

Volume output - yds.3./hr. (m3/hr.)* 25 (19) 0 to 40 (0 to 30) 0 to 50 (0 to 38) 0 to 60 () to 46)Maximum aggregate size - in. (mm) 1/2" (12) 1-1/2 (38) 1-1/2 (38) 1-1/2 (38)Vertical pumping distance - ft. (m)* Excess of 150 (46) 300 (91) 300 (91) 300 (91)Horizontal pumping distance - ft. (m)* 500 (152) 1,000 (305) 1,000 (305) 1,000 (305)Maximum concrete pressure - PSI (bar)* 500 1,100 (76) 1,100 (76) 1,100 (76)

ENGINEEngine, HP (kW) Deutz diesel F2L201-30 (22) or Deutz turbo diesel BF4L201F - Deutz turbo diesel BF4L201F - Deutz turbo diesel BF4L914F -

Nissan A15-51 (38) 79 (59) 79 (59) 99.5 (74)Concrete cylinders - in. (mm) 6 x 12 6 x 36 (152 x 915) 6 x 36 (152 x 915) 6 x 36 (152 x 915)Hydraulic cylinders - in. (mm) — 3 x 36 (76 x 915) 3 x 36 (76 x 915) 3 x 36 (76 x 915)Engine cover (hood) Standard Standard Standard StandardHydraulic oil capacity - gal. (liter) — 58 (219) 58 (219) 58 (219)Hydraulic oil cooler — Standard, with fan Standard, with fan Standard, with fanPump outlet - in. (mm) 3 (76) 5 (127) HD 5 (127) HD 5 (127) HDPump Reciprocating piston — —Hopper remixer — Standard Standard StandardHopper height - in. (mm) 52 (1321) 42 (1067) 42 (1067) 42 (1067)Hopper capacity - cu. ft. (liter) 6 (.17m3) 10 (283) 10 (283) 10 (283)Fuel tank capacity - gal. (liters) — 40 (151) 40 (151) 40 (151)Brakes Hydraulic surge Hydraulic surge Hydraulic surge

DIMENSIONSL x W x H - in. (cm) 144 x 59 x 64.5 172 x 67 x 54 172 x 67 x 54 172 x 67 x 54

(366 x 149 x 164) (437 x 170 x 137) (437 x 170 x 137) (437 x 170 x 137)Weight without fuel - lb. (kg) 2,910 (1320) 4,760 (2159) 4,760 (2159) 5,190 (2354)

LS-400

LS-500

LS-600

C30HD

* Pumping distances shownare to be used as a guide-line only. Maximum attain-able distances, maximumaggregate size and mini-mum slump are all depen-dent on the concrete mixdesign and pipeline diame-ter and other jobsite condi-tions. Maximum output anddistances cannot beachieved simultaneously.

17

1

ORIGINAL SILVERThe Industry Standard Power Trowel Blade

The Wagman Original Silver Blade was developed using ASW 80 CR2 Torque Flex Steel™, the longest lasting proprietary alloy tool steel available. Wagman’s heavy-duty construction makes it one of the most consistent wearing and longest lasting blades available.

• For use on walk-behind and ride-on power trowels.• Silver polished blade gives maximum flex to ensure a smooth, chatter-free finish.• Available in finish and combination blade types.• Full line of float blades also available.

Part # Blade Size Blade Type Blades per carton Wt. per Ctn. Lbs.

WX-614F 6 x 14 Finish 4 11

WX-8140 8 x 14 Combination 4 14

WX-1014FO 10 x 14 Float 4 21

WX-618F 6 x 18 Finish 4 14

WX-818F 8 x 18 Finish (8" Flat Finish w/Round Corners) 4 18

WX-8180 8 x 18 Combination 4 18

WX-1018HD 10 x 18 Float 4 30

GOLD PRO®

Pure Performance Blade for Ride-On Trowels

The Wagman Gold Pro® is a blade built tough to meet the punishing demands of ride-on power trowels or any other application where long lasting life is required.Construction from extra thick high-performance tool steel, the Gold Pro® is the longest lasting steel blade available. Since the Gold Pro Blade® is made from a heavier weight steel and tends to be a bit more stiff, Wagman suggests that the Gold Pro Blade® be used primarily on riding trowel machines.

• High chrome and carbon content increases abrasion resistance.• Field tested and proven to provide 25% to 50% longer life than most silver trowel blades.• Available in finish and combo blade styles only.

Part # Blade Size Blade Description Blades per Carton Wt. per Ctn. Lbs.

WX-614 PRO 6 x 14 Finish 4 14

WX-618 PRO 6 x 18 Finish 4 18

WX-8180 PRO 8 x 18 Combination 4 22

PRO FLOAT PAN®

The Longest Lasting Pan for the Flattest Floors

• STRENGTH – Float pan clips are mig welded on three sides ensuring maximum strength and preventing blades from jamming.

• PRECISION – Precise dish and flange design prevents “oil canning” and keeps the pan from digging into the concrete.

• HIGH-PERFORMANCE – Specialized float steel provides consistent wear for maximum performance.

RM Item # Brand Description Size Number of blades

WFP-24-E-4 Wagman Pro Float Pan Fits Terex, Bartell & Whiteman 2' 4

WFP-36-B-M-4 Wagman Pro Float Pan Fits Whiteman Rider 3' 4

WFP-36-M-4 Wagman Pro Float Pan Fits Wacker, Allen Rider 3' 4

WFP-45-M-4 Wagman Pro Float Pan Fits Whiteman, Allen Rider 4' 4

WFP-45-M-5 Wagman Pro Float Pan Fits Whiteman, Allen Rider 4' 5



WFP-60-M-6 Wagman Pro Float Pan Fits Whiteman Rider 5' 6

WFP-62-M-5 Wagman Pro Float Pan Fits Allen Rider 5' 5

1943

-7-1

0

TROWEL BLADES / FLOAT PANS

18

150

253-

1-10

CONCRETE SAWS

150D

Husqvarna Soff-Cut 150 / 150 D

Applications:

• Ultra Early Entry™ concrete cutting system to reduce random cracking. (150)

• Designed for residential and light commercial applicationssuch as driveways and parking lots.

• 150D is designed especially for the contractor who wants ano-hassle way to make decorative cuts.

Benefits:

• Gasoline saw with easy pull start engine.

• Patented low-noise and low-dust blade block enclosure.

• Mechanical blade depth control.

• Non-marking and non-stick polyurethane wheels.

• Retractable front guide system.(150)

• Self-aligning guide wheels guarantee proper bladealignment with the saw joint every time.(150 D)

• Folding handle.

• Patented safety arbor. (150)

• High strength single piece frame.

• Integrated weight block maintains proper weight balancefor a consistent cut. (150 D)

Applications:

• Ultra Early Entry™ concrete cutting system to reducerandom cracking.

• Handheld electric saw designed for finish cuts, scoring and decorative applications.

Benefits:

• Low-noise and low-dust blade block enclosure withdust extraction port.

• 12 amp 120 volt electric motor.

• Adjustable blade depth control 1/4" - 1" (6-25mm).

• Retractable front guide system.

• Rear guide.

• Curvilinear scoring at 2 ft. (.6m) minimum radius at1/2" (13mm) depth.

• Chase existing curvilinear saw cuts with 5 ft. (1.5m)minimum radius using ProEdge beveled blades.

• Patented safety arbor.

• Adjustable motor position for operator comfort.

• Cuts to < 1" (25mm) from the wall.

• Paddle switch allows multiple hand positions to ease operator fatigue.

• Spring retractable guide system.

Husqvarna Soff-Cut 50

Product Specifications Soff-Cut 150 / Soff-Cut 150 D Soff-Cut 50Item no. 966844801 / 966844803 966844701Maximum blade diameter, in. (mm) 6 (152) 5 (127)Maximum depth of cut, in. (mm) 1-3/16 (30) 1 (25.4)Maximum power, hp* 4.3Average bladeshaft, rpm 3,800 11,000Blade flanges, in. (mm) 3 (76) 1.5 (38.1)Power source Gasoline Electric 120/12Arbor Triangular TriangularBladeshaft diameter, in. (mm) 3/4 (19) .67 (17)Displacement, cu. in. (l) 7.69 (126)Bore/stroke, in. (mm) 2.9 (58)/1.9 (48)Cylinders/cycle 1/4Fuel capacity, gal. (l) 0.7 (2.7)Oil capacity, qt. (l) 0.63 (0.60)Air filter Dry type dual element with pre-cleanerStarter RecoilEngine cooling AirAxle front/rear, in. (mm) 3/4 (19)/3/4 (19)Wheels front, in. (mm) 3 x 3 (76 x 76 ); 1 eachWheels rear, in. (mm) 3 x 3 (76 x 76 ); 2 eachHandlebar adjustment Fixed FixedBlade guard type Enclosed EnclosedNumber of belts 1Blade depth control Manual ManualEngine manufacturer RobinEngine specifications EX13Maximum weight uncrated, lbs. (kg) 87 (39) / 102 (46) 9 (4)Maximum weight crated, lbs. (kg) 91 (41) / 108 (49) 9-1/2 (4.3)Dimensions uncrated, in. (mm) LxWxH 68 x 19 x 33-1/2 (1,727 x 483 x 851) 22 x 10 x 9-1/2 (559 x 254 x 241)

*As rated by the engine manufacturer.

50

19

1

750

2000

253-

2-10

CONCRETE SAWS

Husqvarna Soff-Cut 750 / 2000 / 4000

Applications:

• Ultra Early Entry™ concrete cutting system to reduce random cracking.

• Soff-Cut 750 is ideal for light to medium-duty usage oncommercial and industrial applications.

• Designed for heavy-duty usage on highways, runways,commercial and paving applications. (2000, 4000)

• Three blade widths can be used, allowing different jointwidths and crack control simultaneously. (2000, 4000)

Benefits:

• Self-propelled gasoline saw with hydrostatic transmission.


• Mechanical blade depth control. (750)

• Electric blade depth control. (4000)

• High strength single piece frame. (750)

• Center lifting handle.

• Distinctive roll cage style framework.

• Easy pull start engine. (750)

• Electronic key start. (4000)

• Electronic remote key start and choke. (2000)

• Patented dry-cut diamond blade, anti-ravel skid plate andsafety arbor.


Product Specifications Soff-Cut 2000 Soff-Cut 4000 Soff-Cut 750Item no. 966845301 966845101 966845101Maximum blade diameter, in. (mm) 10 (254) 13-1/2 (343) 8 (203)Maximum depth of cut, in. (mm) 1-1/2 (38) 3 (76) 1-3/16 (30)Maximum power, hp* 9 20 5.7Average bladeshaft, rpm 3,600 3,500 3,800Blade flanges, in. (mm) 4-1/4 (108) 5-7/8 (150) 4-1/4 (108)Power source Gasoline Gasoline GasolineArbor Triangular Triangular TriangularBladeshaft diameter, in. (mm) 1-1/4 (32) 1-1/2 (38) 1-1/4 (32)Displacement, cu. in. (l) 16.2 (265) 39.1 (640) 10.3 (169)Bore/stroke, in. (mm) 2.9 (75)/2.3 (60) 3.0 (77)/2.6 (67) 2.6 (66)/1.8 (46)Cylinders/cycle 1/4 2/4 1/4Fuel capacity, gal. (l) 1.59 (6.0) 4.34 (16.4) 0.95 (3.6)Oil capacity, qt. (l) 1.05 (1.0) 2 (1.9) 0.63 (0.60)Air filter Dry type dual element with pre-cleaner Heavy-duty canister Dry type dual element with pre-cleanerStarter Electric Electric RecoilEngine cooling Air Air AirAxle front/rear, in. (mm) 1 (25.4)/1 (25.4) 1 (25.4)/1 (25.4) 1 (25.4)/1 (25.4)Wheels front, in. (mm) 4 x 4 (102 x 102); 2 each 4 x 4 (102 x 102); 2 each 4 x 4 (102 x 102); 2 eachWheels rear, in. (mm) 10 x 3-5/8 (254 x 92); 1 each 10 x 3-5/8 (254 x 92); 1 each 8 x 2-3/16 (203 x 74); 1 eachHandlebar adjustment Fixed Fixed FixedBlade guard type Enclosed Enclosed EnclosedNumber of belts 2 (1 each banded 3VX) 3 (1 each banded 3VX) 2 (1 each banded 3VX)Blade depth control Manual Electric ManualEngine manufacturer Robin Kohler RobinEngine specifications EX27 CH20 EX17Maximum weight uncrated, lbs. (kg) 420 (191) 420 (191) 243 (110)Maximum weight crated, lbs. (kg) 518 (235) 518 (235) 293 (133)Dimensions uncrated, in. (mm) L x W x H 94 x 29 x 34 (2,388 x 737 x 864) 94 x 29x 34 (2,388 x 737 x 864) 67 x 19 x 38 (1,712 x 485 x 970)

4000

20

253-

6-10

CONCRETE SAWS

Husqvarna Soff-Cut 450

Applications:

• Ultra Early Entry™ concrete cutting system to reducerandom cracking.

• Designed for light to medium-duty usage on driveways,parking lots and residential applications.

Benefits:

• Mechanical remote engine throttle control.

• Flat folding handle.

• Remote engine choke control and engine shut-off switch.

• Easy pull start engine.

• Mechanical remote retractable guide arm.



Husqvarna Soff-Cut 390 Applications:

• Ultra Early Entry™ concrete cutting system toreduce random cracking.

• Electric saw designed for residential and lightcommercial applications.

Benefits:

• Accessible mechanical on/off safety switch.

• Aggregate adjustment system.

• Hour meter.

• 110 volt, 15 amp electric motor.

• Spring retractable guide system.

• Patented anti-ravel skid plate and safety arbor.

Product specifications. Soff-Cut 390 Item no. 966844901Maximum blade diameter, in. (mm) 5-1/2 (140)Maximum depth of cut, in. (mm) 1-1/8 (29)Average bladeshaft, rpm 5,800Voltage/amps 110/15Blade flanges, in. (mm) 1.5 (38.1)Power source ElectricArbor TriangularBladeshaft diameter, in. (mm) .67 (17)Wheels front, in. (mm) 2-1/2 (64); 1 eachWheels rear, in. (mm) 2-3/4 (70); 2 eachHandlebar adjustment Additional extensionsBlade guard type EnclosedBlade depth control ManualMaximum weight uncrated, lbs. (kg) 27 (12)Maximum weight crated, lbs. (kg) 74 (34)Dimensions uncrated, in. (mm) L x W x H 44-1/4 x 15 x 11-1/2 (1,124 x 381 x 292)

Product Specifications. Soff-Cut 450 Item no. 966845001Maximum blade diameter, in. (mm) 8 (203)Maximum depth of cut, in. (mm) 1-3/16 (30)Maximum power, hp* 5.7Average bladeshaft, rpm 3,800Blade flanges, in. (mm) 3-3/4 (95)Power source GasolineArbor TriangularBladeshaft diameter, in. (mm) 1 (25)Displacement, cu. in. (l) 10.3 (169)Bore/stroke, in. (mm) 2.6 (66)/1.8 (46)Cylinders/cycle 1/4Fuel capacity, gal. (l) 0.95 (3.6)Oil capacity, qt. (l) 0.63 (0.60)Air filter Dry type dual element with pre-cleanerStarter RecoilEngine cooling AirAxle front/rear, in. (mm) 3/4 (19)/1 (25.4)Wheels front, in. (mm) 3 x 3 (76 x 76); 2 eachWheels rear, in. (mm) 8 x 3 (203 x 76); 2 eachHandlebar adjustment 2 PositionBlade guard type EnclosedNumber of belts 2 (1 each 2 band 3VX)Blade depth control ManualEngine manufacturer RobinEngine specifications EX17Maximum weight uncrated, lbs. (kg) 143 (65)Maximum weight crated, lbs. (kg) 265 (120)Dimensions uncrated, in. (mm) L x W x H 60 x 18-3/4 x 38-1/2 (1,524 x 476 x 978)

*As reted by the engine manufacturer.

21

1

253-

3-10

CONCRETE SAWS

Husqvarna Soff-Cut 2500 / 4200 / 5000

Applications:

• Ultra Early Entry™ concrete cutting system to reduce random cracking.

• Ideal for medium to heavy-duty usage on highways, runways, commercial, industrial and paving applications.

• Multiple blade widths can be used, allowing different joint widths and crack control simultaneously.

Benefits:

• Self-propelled gasoline saw with positraction drive, hydrostatic transmission and travel speed indicator.

• Switch-activated electronic adjustable handle. (2500, 4200)

• Master switch control panel. (2500, 4200)

• Electronic remote key start and choke.

• High-strength, lightweight aluminum frame.

• 10 amp (2500), 20 amp (4200), 15 amp (5000) regulatedcharging systems.

• Switch-activated blade depth control and retractable guide.

• Mechanical depth gauge. (4200, 5000)



2500

4200

5000


Product Specifications Soff-Cut 2500 Soff-Cut 4200 Soff-Cut 5000 Item no. 966845401 966845601 966845701Maximum blade diameter, in. (mm) 10 (254) 13-1/2 (343) 14 (350)Maximum depth of cut, in. (mm) 1-1/2 (38) 3 (76) 4 (100)Net power, hp* 11 23 27Average bladeshaft, rpm 3,200 3,500 2,900Blade flanges, in. (mm) 4-1/4 (108) 5-7/8 (150) 4-3/4 (120)Power source Gasoline Gasoline GasolineArbor Triangular Triangular TriangularBladeshaft diameter, in. (mm) 1-1/4 (32) 1-1/2 (38) 1-1/2 (38)Displacement, cu. in. (l) 23.7 (389) 41.1 (674) 44 (725)Bore/stroke, in. (mm) 3.5 (88) 3.2 (80)/2.6 (67) 3.3 (83)/2.6 (67)Cylinders/cycle 1/4 2/4 2/4Fuel capacity, gal. (l) 1.6 (6.1) 3.16 (12) 3.16 (12)Oil capacity, qt. (l) 2.3 (1.1) 2 (1.9) 2 (1.9)Air filter Dry type dual element Heavy-duty canister Heavy-duty canisterStarter Electric Electric ElectricEngine cooling Air Air AirAxle front/rear, in. (mm) 3/4 (19)/1 (25.4) 1 (25.4)/1 (25.4) 1 (25.4)/1 (25.4)Wheels front, in. (mm) 4 x 3 (102 x 76); 2 ea. 4 x 4 (102 x 102); 2 ea./4 x 2 (102 x 51); 1 ea. 4 x 4 (102 x 102); 2 ea./4 x 2 (102 x 51); 1 ea.Wheels rear, in. (mm) 8 x 3 (203 x 76); 2 ea. 11 x 4 (279 x 102); 2 ea. 11 x 4 (279 x 102); 2 ea.Handlebar adjustment Electric Electric ElectricBlade guard type Enclosed Enclosed EnclosedNumber of belts 2 (1 each 2 band 3VX) 3 (1 each 3 band 3VX) 4 (1 each 4 band 3VX)Blade depth control Electric Electric ElectricEngine manufacturer Honda Kohler KohlerEngine specifications GX390 CH23 CH740Maximum weight uncrated, lbs. (kg) 347 (157) 488 (221) 495 (225)Maximum weight crated, lbs. (kg) 418 (190) 568 (258) 593 (269)Dimensions uncrated, in. (mm) L x W x H 76 x 23 x 36 (1,930 x 584 x 914) 89 x 30 x 40-1/4 (2,261 x 762 x 1,022) 95 x 30-1/2 x 41 (2,413 x 775 x 1,041)

22

253-

5a-1

0

CONCRETE SAW BLADES

Husqvarna Soff-Cut® color coded diamond blades and patented skid plates are designed and tested to meet all aggregateconditions. The blades are top quality and designed to work specifically with the Soff-Cut® system, the only true Ultra EarlyEntry™ system.

Chases existing standard saw cuts to bevel edges on 45° angle or round corners to 1/4" or 1/2" radius. Usethese decorative Soff-Cut Pro-Edge beveled blades to achieve a “Tooled Joint” look.

150/150D Saws XL6-V21 XL6-V23 XL6-V25 XL6-V38 XL6-V500 XL6-R250 XL6-R500

390 & 50 Saws XL5-V21 XL5-V25 XL5-V23 XL5-R250 XL5-R500

JOINT PROFILE BLADES• The Husqvarna ProEdge joint profile blades feature a unique triangular safety arbor configuration.• The V-Line and Radius Line blades bevel the cut, allowing for straighter joint lines, higher production and reduced labor

versus hand tooling.• These blades are ideal for residential and commercial applications, including driveways, sidewalks, hardscape, patios, pool

decks, parking garages and commercial sitework.• With the Soff-Cut® system, the ProEdge blades and model 390, 50, 150 and 150 D saws can be used to chase standard

joints for a beveled look the day after early entry dry-cut control joints are cut.

DIAMOND BLADES FOR ULTRA EARLY ENTRY™ SAWS

The Excel 1000 Series Purple is recommended for ultra hard aggregate, non-abrasive sand.The Excel 2000 Series Green is recommended for hard aggregate, non-abrasive sand.The Excel 3000 Series Red is recommended for medium to hard aggregate, medium abrasive sandThe Excel 4000 Series Orange is recommended for medium aggregate, medium abrasive sand.The Excel 5000 Series Yellow is recommended for medium to soft aggregate, abrasive sand.The Excel 6000 Series Black is recommended for soft aggregate, abrasive sand.The Excel Turbo is recommended for soft aggregate, soft manufactured sand (limestone).

Husqvarna Score Cutting Blade for 150 Saw.Score cuts 1/2" deep (maximum) in cured concrete.

Husqvarna Soff-Cut Excel Series Blades

Pro-Edge Beveled Blades

1

23

• Metal bond tools are used in the initial grinding and polishing stages. The Husqvarna metal bond diamond selection offers a wide choiceof bonds and grit sizes, all with the choice of double or single segments to suit the application and budget of the end user.

• The Husqvarna Redi Lock™ system eliminates the need for multiple sets of diamond holder discs for different sets of diamond tooling. Itremoves the necessity for the more time consuming and impractical screw-on-diamond systems as segments simply lock into the slotsand are ready for use. The system is available for a variety of machine manufacturers.

• Premium-quality resin-bond polishing pads can be chosenfor high-end polishing, with a grit range from 50 to 3000.Husqvarna resin pads are easy to attach to the PGmachinery range with a simple Velcro system and are alsoavailable for handheld machinery.

1067

-28-

10

SURFACE PREPARATION

24

Husqvarna PG 530TECHNICAL SPECIFICATIONSPower output 5 hpRated current 16AVoltage 220-240 VPhases 1, 3Grinding width 21"Weight 475 lbs.

Husqvarna PG 680TECHNICAL SPECIFICATIONSPower output 17 hpRated current 32 AVoltage 380 / 480 VPhases 3Grinding width 27"Weight 850 lbs.

Husqvarna DC 3300TECHNICAL SPECIFICATIONSPower output 4 hpRated current 16AVoltage 220 / 240 VPhases 1Air Flow 325 cfmMax. vacuum 4.35 psiWeight 214 lbs.

METAL BOND DIAMOND TOOLS

Husqvarna DC 5500TECHNICAL SPECIFICATIONSPower output 7.4 hpVoltage 380 / 480VRated current 32AAir Flow 350 cfmMax. Vacuum 4.35 psiWeight 474 lbs.

Husqvarna PG 820TECHNICAL SPECIFICATIONSPower output 17 hpRated current 32 AVoltage 380 / 480 VPhases 3Grinding width 32"Weight 970 lbs.

PG 820DC 5500

DC 3300

PG 680

PG 530

Switch entire sets ofdiamonds instantly.

97-7

-06

SAW / SCARIFIER

8" WALK BEHIND SCARIFIER

10" SELF-PROPELLED SCARIFIER

14" MASONRY SAWS

18" DOWNCUT - CONCRETE &ASPHALT SAWS

PRODUCTION RATE:8" Working Width will scarify approximately 350-500 Sq. ft. per hour at Depth Per Pass of 1/8"

Removes traffic lines at 800-1,000 lineal ft. per hour

PRODUCT NOTES:- Optional edger attachment

allows the CPM-8 to get within 1-3/4" of any vertical surface

IDEAL FOR:- Sidewalk trip hazard repair- Concrete and coatings removal- Floor cleaning and/

or preparation- Traffic line and markings removal- Creating non-slip surfaces

PRODUCT NOTES:- 14" blade capacity- Adjustable cutting head can be used

manually or locked in a fixed position- Gasoline units have a large capacity,

3-stage filter that protects the engine from wear

- Electric BB-14 unit has a totally enclosed fan-cooled motor

- Gasoline units include a belt driven connectable and disconnectable water pump

- Electric BB-14 unit includes a 115V submersible water pump with a water proof switch

IDEAL FOR:- Professional masons,

paver installers, paver manu-facturers, landscape suppliers, masonry suppliers and rental stores

PRODUCTION RATE: 10" working width will scarify approximately500-750 Sq. ft. per hour at Depth Per Pass of 1/8"

PRODUCT NOTES:- Upcut drum rotation- Optional Outrigger Axle Assembly enables the machine to

follow slab contours closely when working on uneven surfaces or when uniformsurface removal is critical

- Hydrostatic drive transmission pro-vides a smooth forward and reverse speed control

IDEAL FOR:- Parking deck and

road repairs- Factory floor cleaning

and/or preparation- Mall floor repairs

SPECIALTY SET-UPS:- Convertible hood design on CPU-10FC model

allows for multiple drum set-ups and provides easy accessfor quick drum changes

PRODUCT NOTES:- Wide “T”

handles with rubber grips

- Heavy-duty arbor shaft assembly with 18" blade capacity

- Heavy-duty, 7-gauge steel frame and under-carriage eliminates bending and vibration

- Dual blade arbor cutting capabilities- Easy turn, large diameter crank for lowering and raising blade

in and out of cut- Turn-to-lock throttle cable- Solid-steel handles and lifting bail for easy loading

and unloading- Heavy-duty, anti-vibration engine mount- Screw boot belt tensioner prevents frame damage

IDEAL FOR: - Short-run slab cutting, contraction joints, patch repairs

in asphalt, traffic loop installation and trenching

Numerous Cutter Drumsetups are available includingDiamond Blade Groovingsetups to achieve varioussurface profiles.

BB-14G

BB-14E

25

1

97-6

-10

GRINDERS / ACCESSORIES

10" TURBO GRINDER

PRODUCTION RATE: 10" Working Width will grind approximately 400-500 Sq. ft. per hour at 1/16" with an EDCO Diamond Disc

INCLUDES: 1–10" Diamond Disc and Standard Vacuum Port

REQUIRES: 1–10" Diamond Disc

RIGID HEAD ASSEMBLY IS IDEAL FOR:- Grinding uneven expansion joints,

high spots, joint curls and bridge decks

- Removing coatings- Grinding rough concrete surfaces

FLEX HEAD ASSEMBLY IS IDEAL FOR:- Preparing a smooth, flat floor to

receive a new coating- Removing coatings- Grinding rough concrete surfaces- Grinding surfaces 4 times faster than a traditional floor grinder

The TG-10, TURBO GRINDER, comesstandard with a rigid head assembly

PRODUCTION RATE: 7" Working Width will grind approximately 400-500 Lineal ft. per hour at 1/16" with an EDCO Diamond Cup Wheel

INCLUDES: 1–7" Diamond Cup Wheel andStandard Vacuum Port

REQUIRES: 1–7" Diamond Cup Wheel

OPTIONAL: 1–7" Scarifier Assembly with Solid Carbide Cutters*(*Must have rigid head assembly to use this accessory)

FLEX HEAD ASSEMBLY IS IDEAL FOR:- Grinding tightly against any vertical surface- Grind around columns or under tanks and

other tight areas- Removing coatings, build-ups, markings overlays or paints

RIGID HEAD ASSEMBLY IS IDEAL FOR:- Grinding uneven expansion joints, high spots, bridge decks or

removing coatings in small areas- Grinding curbs and gutters for proper flow trenching- Removing coatings, build-ups, markings overlays or paints

The TMC-7, TURBO EDGE GRINDER comesstandard with a flex head assembly. Anoptional rigid head assembly is available.

DUAL-DISC GRINDERPRODUCTION RATE: 22" Working Width will grind

approximately 400-500 Sq. ft. per hour at 1/32" with EDCO Dyma-Serts™

INCLUDES: 2–Multi-Accessory Disc, 2" Vacuum Port & Water Port Electric models have a 115/230 Voltage Selector Switch

REQUIRES: 6–Grinding Insert Accessories per loading

IDEAL FOR:- Smoothing concrete in

large and small areas- Light grinding or cleaning

of concrete surfaces- Removing mastics, thin-set,

sealers, epoxies and urethanes

7" TURBO GRINDER

7" TURBO GRINDER ACCESSORIES

7" DIAMOND CUP WHEELSDESCRIPTION: 17 SegmentT, dry cut grinding wheel40-50 GRIT – PART# 72030150 GRIT – PART# 72031

Cup wheels can be used with the rigid head or flexhead assembly on EDCO’S TMC-7.

10" DIAMOND DISCS

GENERAL PURPOSE DISCPART #19166General Purpose ConcreteMedium Bond (7 MATRIX)30-40 GRIT

ABRASIVE DISCPART #19165Green ConcreteHard Bond (9 MATRIX)30-40 GRIT

GENERAL PURPOSE/ABRASIVE DISCPART #19161Green/General Purpose ConcreteMedium-Hard Bond (7 MATRIX)30-40 GRIT

OTHER DIAMONDDISCS AVAILABLESoft Bond-Orange Disc30-40 GRIT DISC: PART # 19164Fine & Very Fine Discs80 GRIT DISC: PART #19164120 GRIT DISC: PART #19163

Dyma-Serts™ are diamond segments welded to a backing plate to improve grind-ing speed and remove tough coatings.

PRODUCTION RATE: 5 Times faster than grinding stones. Long lasting — up to 30,000 sq. ft. (2,800 square meters) of grinding action

IDEAL FOR: - Smoothing rough surfaces or trowel marks- Grinding concrete or Terrazzo- Repairing damaged concrete slabs- Removing epoxy thin-coats- Grinding sharp aggregates such as

flint and granite- Removing surface imperfections

from epoxy mortars- Removing thin mastics and thin-set- Leveling and smoothing uneven surfaces

7" SCARIFIER ASSEMBLYDESCRIPTION: Solid, 15-point carbide cutter discassemblyPART# 72040

Scarifier assembly discs can only be used with therigid head assembly on EDCO’S TMC-7

DYMA-SERTS™

For ConcreteEG-1, XGeneral Purpose – Part #19110EG-2X, Abrasive Concrete – Part #19130EG-3X, Epoxy Mortars – Part #19180

For TerrazzoEG-5X, 50 grit – Part #19250EG-7X, 80 grit – Part #19260EG-9X, 120 grit – Part #19270

26

1930

-44-

10

CONCRETE / MORTAR MIXERS

27

Mortar mixers for the professional!Choose from steel or EasyClean™ polyethylene drums.You choose.Available in 7, 9, and 12 cubic foot capacities, with your choice of power and drum materials.

EM70S (7 cu. ft.)

WM90P (9 cu. ft. Poly drum)

WM94S (9 cu. ft.)

WM94P (9 cu. ft.)

“The ultimate in heavy-duty concrete mixers.”

Available in 4-, 6- and 9-cubic foot capacities, with yourchoice of power and drum materials.*

* Whiteman 4-cubic foot models available with steel drums only.

12 cu. ft. HYDRAULIC DRIVE...• Mixes larger, stiffer loads — smooth and consistent.

Eliminates high wear components, V-belts, gears and clutches.• Hydraulic dump system — allows high production with minimal

operator fatigue (optional).• Greatly reduced maintenance.• Dual controls — mixing blades and optional hydraulic dump.• Rugged 14 gauge steel engine covers with punched ventilation

openings for increase cooling and added strength.• Built-in hydraulic safety relief system — immediately disengages

itself in case an object becomes wedged in the drum. Automaticallyresets when problem is corrected.

• Seal system — double-sealed bearings with spring-loadedgreasable shaft seals (on hydraulic mixers only).

12 cu. ft. MECHANICAL DRIVE...• Ideal for high production.• Reduced maintenance — hardened drive gear and

multiple disc clutch are immersed in oil and fully protectedfor long, trouble-free life.

• Elimination of high-wear components — V-belts, pulleys,and external gears.

• Easily accessible blade engagement lever.

7 cu. ft. 9 cu. ft. 12 cu. ft. 12 cu. ft. 4 cu. ft. 6 cu. ft. 9 cu. ft.Plaster/Mortar Steel Drum Models Concrete Mixers Steel DrumWhiteman WM70S WM90S WM120SM (mechanical) WM120SH (hydraulic) MC44S MC64S MC94SEssick EM70S EM90S EM120SM (mechanical)Plaster/Mortar Poly Drum Models Concrete Mixers Poly DrumWhiteman WM70S WM90S WM120SM (mechanical) WM120SH (hydraulic) – MC64P MC94PEssick EM70S EM90S EM120SM (mechanical)

1

1067

-26-

10

MASONRY SAW

Applications:• Large jobs for cutting block, brick or pavers.

Benefits:• Now available with 9 hp Subaru and

11 hp Honda engine.• High torque, continuous duty dual capacitor motors

make efficient use of horsepower and reduce cutting time.• New repaceable guide rails make alignment of the

cart easier.• Capable of cutting 8" x 8" x 16" block in one pass with a

20" blade.• Only two pivot points for reduced saw maintenance and

longer diamond blade life.• Height can be controlled with a convenient crank control

or foot pedal.• The Sta-level® blade guard keeps parallel to the cutting

table for accurate cuts.• Clutch available on 11 hp Honda model so blade does

not spin while idling.

Guardmatic® MS 510 and MS 510 G

28

TECHNICAL SPECIFICATIONS MS 510 MS 510 MS 510 MS 510 MS 510 MS 510 G MS 510 G Item no.Item no. 966006601 966006603 966006602 966006604 966606605 (230V-3P) 96606607 96606608

966006606 (460V-3P)Item no. with clutch 966006609Blade diameter - in. (mm) 14 (350) 14 (350) 20 (508) 20 (508) 20 (508) 20 (508) 20 (508) Bladeshaft rpm 3,090 3,090 2,317 2,317 2,317 3,500 2,202Maximum depth of cut - in. (mm) 5 (127) 5 (127) 8 (203) 8 (203) 8 (203) 8 (203) 8 (203)Arbor size - in. (mm) 1 (25.4) 1 (25.4) 1 (25.4) 1 (25.4) 1 (25.4) 1 (25.4) 1 (25.4)Bladeshaft bearings Ball bearings Ball bearings Ball bearings Ball bearings Ball bearings Ball bearings Ball bearingsNumber of belts 2 V-belts 2 V-belts 2 V-belts 2 V-belts 3 V-belts 3 V-belts 3 V-beltsBlade guard type, Sta-Level® One-piece steel One-piece steel One-piece steel One-piece steel One-piece steel One-piece steel One-piece steelConveyor cart Cast aluminum Cast aluminum Cast aluminum Cast aluminum Cast aluminum Cast aluminum Cast aluminumWater pump, high output Submersible Submersible Submersible Submersible Submersible Belt driven Belt drivenWeight - lbs. (kg) crated 360 (161) 361 (162) 360 (161) 361 (162) 368 (165) 495 (222) 495 (222)

uncrated 332 (149) 333 (150) 332 (149) 333 (150) 395 (177) 368 (165) 368 (165)Power source Electric Electric Electric Electric Electric Gasoline GasolineMotor/engine Baldor Baldor Baldor Baldor Baldor Honda HondaSpecifications T.E.F.C T.E.F.C T.E.F.C T.E.F.C T.E.F.C EX27X GX390Net horsepower* 3 5 3 5 7-1/2 9 11Voltage 208/230 208/230 208/230 208/230 230/460Cycle/current/phase 60/AC/1 60/AC/1 60/AC/1 60/AC/1 60/AC/3Full load amps 14.5/13 21.5/20 14.5/13 21.5/20 19.4/9.7Starting amps 188/95 149/139 188/95 149/139 166/83Starter Capacitor Capacitor Capacitor Capacitor Capacitor Recoil RecoilEngine cooling Air Air Air Air Air Air AirDisplacement - cu. in. (l) 16.5 (270) 23.7 (389)Bore - in. (mm) 3.0 (77) 3.5 (88)Stroke - in. (mm) 2.3 (58) 2.5 (64)Cylinders/stroke 1/4 1/4Fuel capacity - gal. (l) 1.4 (5.3) 1.6 (6.1)Oil capacity - qt. (l) 1.2 (1.1) 1.2 (1.1)Air Filter Dual Element Cyclone *As rated by the engine manufacturer.

Blade sold separately. DESCRIPTION Item No.Wheel-around kit† 034000Rip guide 030351Conveyor cart wheel kit 189041†For electric guardmatic models only. Includes handlesand drop-down wheels.

Accessories

1067

-27-

08

MASONRY SAW

Applications:• Smaller jobs for cutting brick, block or pavers.

Benefits:• New replaceable rails make alignment of cart easier.• New design has wider opening in back to allow larger

material to pass through.• Saw head comes preassembled to frame.• High torque continuous duty 110 or 220 volt electric

motors, a 4.8 hp Honda gas engine or the new 4.5 hpSubaru gas engine provide high power and long life.

• Only two pivot points for reduced saw maintenance andlonger diamond blade life.

• Plunge cut or lock the head and use with the rolling cart.• The optional foot pedal kit reduces operator fatigue when

plunge cutting.• Sta-level® bladeguard keeps parallel to the cutting table for

accurate cuts.• The side handles make moving the saw easier.• Pivot lock bar moved to front for convenient raise/lower

operation of blade.

Portasaw® MS 355 and MS 355 G

29

TECHNICAL SPECIFICATIONS MS 355 MS 355 MS 355 MS 355 MS 355 G MS 355 GItem no. 966006501 966006502 966006503 966006504 966006505 966006506Blade guard capacity - in. (mm) 14 (350) 14 (350) 14 (350) 14 (350) 14 (350) 14 (350)Bladeshaft rpm 2,150 2,509 2,509 2,509 3,800 2,950Maximum depth of cut - in. (mm) 5 (127) 5 (127) 5 (127) 5 (127) 5 (127) 5 (127)Arbor size - in. (mm) 1 (25.4) 1 (25.4) 1 (25.4) 1 (25.4) 1 (25.4) 1 (25.4)Bladeshaft bearings Ball bearings Ball bearings Ball bearings Ball bearings Ball bearings Ball bearingsNumber of belts 2 V-belts 2 V-belts 2 V-belts 2 V-belts 2 V-belts 2 V-beltsBlade guard type, Sta-Level® One-piece steel One-piece steel One-piece steel One-piece steel One-piece steel One-piece steelConveyor cart Cast aluminum Cast aluminum Cast aluminum Cast aluminum Cast aluminum Cast aluminumWater pump high output Submersible Submersible Submersible Submersible Belt driven Belt drivenWeight - lbs. (kg) crated 171 (77) 171 (77) 182 (82) 191 (86) 209 (95) 209 (95)

uncrated 160 (72) 160 (72) 169 (76) 181 (81) 198 (91) 198 (91)Power source Electric Electric Electric Electric Gasoline GasolineMotor/engine Baldor Baldor Baldor Baldor Robin HondaEngine Specifications T.E.F.C T.E.F.C T.E.F.C T.E.F.C EX13 GX160Net horsepower* 1-1/2 1-1/2 2 3 4.5 4.8Voltage 115 115/208-230 115/208-230 208-230Cycle/current/phase 60/AC/1 60/AC/1 60/AC/1 60/AC/1Full load amps 14.4 17.2/9.5-8.6 16.8/9.3-8.4 14.5/3Starting amps 79@115V 92@115V 63@230V 95@230VStarter Capacitor Capacitor Capacitor Capacitor Recoil RecoilEngine cooling Air Air Air Air Air AirAir filter Dual element Cyclonic*As rated by the engine manufacturer.

Blade and stand sold separately.

DESCRIPTION Item No.Folding stand 034040Skid kit 177401Foot pedal kit 034050Adapter cord - 20A twist to 15A straight 173120Handle carrying kit for all older Portasaw models 190056Conveyor cart complete, gas 177304Conveyor cart complete, electric 030343Rip guide 030350Conveyor cart wheel kit 189041

Accessories and Spare Parts

1

360-

9-10

HOISTS

RGC® PRO Platform HoistsAn RGC Platform Hoist is the most economical, safe and dependable way to raise materials to the roof on residential and commercial job sites. They are available in 200 lb. and 400 lb. lifting capacities, with gas or electric power drives, and 12 ft., 16 ft., 28 ft. or 44 ft. of track.

FEATURES AND BENEFITS:

• Easy transporting and no lifting required to mount the PRO Power Drive on track saves set up time and man power.

• Dual anchor points on 2nd and 3rd track cross ties with PRO Drive add to stability of system.

• Single handle control provides convenient, safe operation away from the load with minimal operator effort on the PRO Drive.

• Sturdy steel frame around the PRO Drive protects it.

• 33% larger cable drum diameter promotes longer wire rope life on the PRO Drive.

• The Classic Power Drive is ideal for use on steeper landscapes because it mounts higher on the track.

• Dual anchor points on 3rd and 5th track cross ties with the Classic Drive add to stability of system.

• Dual handle controls provide convenient, safe operation away from the load with minimal operator effort on Classic Drives.

• Brake rope design allows safe, controlled platform descent without binding due to metal-to-metal contact as with band style braking systems.

• Location of controls keeps the operator safely to side of load, not under it.

• PRO and Classic Drives are available with a 4 hp Briggs & Stratton, 4 hp Honda or 1.5 hp Baldor motor.

• Pulleys with polymer sheaves prolong wire rope life and permit smooth platform movement.

• Quick and easy assembly without any special tools.

• Large, open platform with removable rollers on all models for exceptional versatility.

• Durable, long-lasting steel guide rollers on platform main frame contact track and provide exceptional wear resistance.

• Heavy cast aluminum shoes on base track section help stabilize hoist on both pavement and dirt with full 16 sq. in. contact area.

• Base track sections have cross tie support brackets thatadd rigidity and extra stability to system.

Platform Hoist SpecificationsModel 400 200Load Capacity 400 lbs. 200 lbs.Lift Speed 110 fpm 220 fpmPlatform Size 24 in x 24 in. 17 in. x 18 in.Track ( 3-3/4 in. Side Rail) 24 in. wide 17 in. wide

PRO POWER DRIVES• PRO DRIVE w/ 4 hp B&S Gas Engine• PRO DRIVE w/ 4 hp Honda Gas Engine• PRO DRIVE w/ 1-1/2 hp Baldor Electric Motor

CLASSIC POWER DRIVES• CLASSIC DRIVE w/ 4 hp B&S Gas Engine• CLASSIC DRIVE w/ 4 hp Honda Gas Engine• CLASSIC DRIVE w/ 1-1/2 hp Baldor Electric Motor.

PRO DRIVESWheels make PRO DRIVE transportation and assembly to the trackalmost effortless. The single control lever requires minimal operatoreffort, improves productivity and makes the hoist safe and easy to use.A large cable drum and polymer sheave in the pulleys improve wire ropelife. The brake rope design allows for feathering of the brake, resulting insmooth, controlled platform decent.

CLASSIC DRIVESThe CLASSIC DRIVE mounts to the 3rd and 5th track cross ties for convenient use on steep landscapes. The brake rope design allows forfeathering of the brake, resulting in smooth, controlled platform decent.The drive is easy to operate with minimal operator effort.

30

31

CONCRETE VIBRATOR / ACCESSORIES

SURE SPEED™New Electric Square Head™ Concrete Vibrator� Energy efficient system.� One motor – drives any combination of shaft and head size.� Uniform speed system – one vibrator performs in multiple mixes.� Ergonomic hand grip and adjustable shoulder strap.� Lightweight yet powerful.

ELECTRIC SQUARE HEAD™ CONCRETE VIBRATOR� Deliver more torque with less amps than other motors.� Retain speed under heavier loads.� Allow the use of longer flexible shaft and larger vibrator heads.� Operate at less than 65% of full load capacity under normal job conditions.� Provide 20-50% faster consolidation.

SQUARE HEAD™ CONCRETE VIBRATOR HEADS� Provides 22% more displacement than round heads.� More effective in low-slump concrete than round heads.� One-piece head housing with no threaded tip joint to wear through.� Hardened Square housing has more metal to protect against wear.� The Square Head comes in six standard head sizes: 13/16", 1",1-3/8" ,1-3/4", 2"

and 2-1/4". Optional polyurethane heads are also available.

SQUARE HEAD™ BACKPACK CONCRETE VIBRATOR� Compact, lightweight, durable 40.2cc, two stroke gas engine.� Uses diaphragm carburetor and no low oil shutoff.� Cast aluminum housing contains 2x internal gear speed

increaser, and a simple disconnect for easy storage.� Available with Square Head sizes 13/16", 1", 1-3/8", 1-3/4" and 2".� Adjustable speed allows operator to match vibrator speed to the mix.� Visual readout indicator displays engine speed and total operating hours.� Heavy-duty clutch.� Backpack unit only 20 pounds.� Swivel mounted, isolated frame.� Shafts available in 7', 10' and 14' lengths.

SQUARE HEAD™ EZ VIBE™� Compact, portable hand-held vibrator.� Adjustable speed allows operator to match vibrator speed to the mix.� 35cc air-cooled 4-cycle engine, no need to mix oil in fuel.� 1.6 hp., 0.65 liter fuel capacity motor.� Shaft length is 6 feet and includes a 1.38" head.� Uses a diaphragm carburetor.� Includes shoulder harness and weighs only 23 pounds.� Available with either a Robin or a Honda engine.

SQUARE HEAD™ HIGH CYCLE CONCRETE VIBRATOR� Creates powerful force for consolidation.� Compatible with 230 volt, 3-phase high cycle generators.� 25' power cord.� Maintains uniform speed/frequency under load.� Square Head performance.� Multi-speed capability when used with Select-Cycle converter.

BD PNEUMATIC CONCRETE VIBRATOR� Easy to handle.� Variable air flow rate with a twist grip throttle.� Quiet, smooth operation.� Built-in pneumatically driven motor which has only two moving parts, the vane and rotor.� Available in four head sizes 1-1/2", 2-1/4", 2-3/4", 3" and

hose lengths 10', 15' and 20' lengths. (1-1/2" is only offered in 10' lengths)

587-

9-10

1

608-

5-10

CONCRETE BUCKETS / ACCESSORIES

General Purpose Concrete BucketsGAR-BRO General Purpose or “G” Series Buckets are built for modern concrete requirements and general concrete work. Sturdy design and construction provide long life expectancy. All “G” series buckets feature the GAR-BRO patented Double Clamshell Gate with vertical center discharge. Standardgate size is 15 inches x 22 inches. Extension collars for increased capacity are available for all models

Rated Level Outside LoadingItem Capacity Capacity Diameter Height WeightNo. Cubic Yds. Cubic Ft. Inches Inches Pounds

442-G 1-1/2 42 64 55 795

“R” Series Lightweight Round-Gate Buckets with 16" Diameter GateThe GAR-BRO round gate or “R” series concrete bucket is 30% to 50% lighter than most standard steel buckets of the same capacity. The double clamshell 16" diameter gate featuring the patented GAR-BRO venturi throat is non-jamming, grout tight and self-closing. A variety of attachments are available for all “R” series buckets, including rubber accordion hoppers, side chutes, air-operated gate systems and extension collars.

Rated Level Loading InsideItem Capacity Capacity Height Diameter WeightNo. Cubic Yds. Cubic Ft. Inches Inches Pounds

410-R 1/3 10 34 36 237413-R 1/2 13.5 41 36 257420-R 3/4 20.3 44 45 330427-R 1 27.5 46 54 400440-R 1-1/2 40.5 53 60 500454-R 2 55 58 66 675483-R 3 83 72 66 760

Collection HoppersGAR-BRO Collection Hoppers are designed to facilitate transfer of concrete from the bucket or transit mix truck to restricted areas. Used in conjunction with a variety of chutes or elephanttrunk, the hoppers complete a versatile concrete placement system that will suit any job requirement. For most jobs, a center discharge collection hopper will be used as it is the mostversatile. Other shapes and sizes are also available.

Top DischargeItem Opening Height OpeningNo. Inches Inches Inches803 30 x 30 24 6, 8, 12, 16

Plastic Elephant TrunkElephant Trunk is normally used with collection hoppers for placing concrete into deep or narrow forms. Light and inexpensive polyvinyl chloride (PVC) synthetic, or a nylon reinforced plastic elephant trunk which is sturdy and flexible, yet strong and light. Available in 6-, 8- and 12-inch inside diameter sizes.

Item Inside For use with Rectangular Size Maximum Length WeightNo. Diameter Steel Collar Item No. Inches Feet Per Foot

913-B 8 907 - 908 3 -1/2 x 8-1/2 50 1 lb. 4 oz.

Steel Collars for Elephant TrunkSteel collars are used to support the elephant trunk and connect it to the hopper by chain linkage. Rectangular collars are used when poring into narrow forms. Round steel collars are available in 6-, 8-, 12- and 16-inch diameter sizes. Rectangular collars are available to fit all sizes of elephant trunk.

Item Use with Normal Size WeightNo. Item Number Inches Pounds

908* 913 8 Diam. 4 * Available with Lip for use with PVC Elephant Trunk.

Clamps for 6", 8" and 12" collars available.

Shown with optionalside chute.

32

1022

-8-1

0

MASONRY EQUIPMENT

Heavy-Duty Forklift Mortar Buggies• Durable 10-gauge steel construction.• Top edge of tub channel formed for strength.• Big 1-5/16" diameter tubular steel handle.• Both ends sloped for easy shoveling.• Bolted-on heavy-duty casters.• 2" x 8" high strength poly wheels.• Wheel brakes optional.

MORTAR BUGGIES

Model 106Model Capacity Dimensions Weight105 6 cu. ft. 50-1/2"L x 23-1/2"W x 28"H 165 lbs.106 10 cu. ft. 54"L x 23-1/2"W x 31"H 200 lbs.

Model 102

Model Capacity Dimensions Weight102 10 cu. ft. 48"L x 24"W x 22"H 155 lbs.103 6 cu. ft. 32"L x 24"W x 22"H 121 lbs.

Heavy-Duty Forklift Mortar Tubs• Durable 10-gauge steel construction.• Continuous welded seams.• Reinforced corners.• One end sloped for easy shoveling.

Crane Forks for Block, Brick & General Purpose• King post adjusts for load heights from 48" to 68".• Adjustable stop permits use of 36", 40" and 48" pallets.• Backstop helps stabilize load - 40" wide.• Forks spread up 40" wide (out to out).

CONCRETE RAKESModel 960 – w/60" handleModel 961 – w/48" handle• Contoured, fired ash handle.• 5" x 20" 14-gauge steel blade.

Model Capacity Dimensions Weight(Frame Only)

660 King Post Frame with backstop 300 lbs.(Tines Only)

660-01 6,000 lbs. Gen. Purpose - set of 2 (1½" x 4" x 46") Forged Forks 188 lbs.660-02 6,000 lbs. Block - set of 6 (1½" x 2" x 47") Forged Forks 258 lbs.660-03 4,500 lbs. Brick - set of 2 (1½" x 3" x 39") Forged Forks 110 lbs.

Model 660-02

Model 660-03

MORTAR TUBS

Shown with tines.

Shown with tines.

33

1

1022

-9-1

0

HEAVY-DUTYMASONRY EQUIPMENT

Model 203B

Deluxe Rough TerrainBrick & Block Cart• Tilt capacity – 1,000 lbs.• Accommodates any banded

block or brick package.• More fork adjustment holes

to accommodate banded block packages.

• 4 ply – wide high-float tires.• Heavy-duty 1" dia. axle with 3"

long roller bearings.• Spring loaded positioning wheels.• Overall width 29".• Weight 140 lbs.• Two pair 15" forks and

one pair 8" forks.

Model 202B

Rough Terrain Brick Cart• Tilt capacity – 600 lbs.• Accommodates any banded

brick package.• 4 ply – wide high-float tires.• Heavy-duty 1" dia. axle

w/3" roller bearings.• Overall width 29".• Weight 115 lbs.• One pair 8" forks.

BRICK AND BLOCK CARTS

VENEER SCAFFOLD

MASONRY STANDS

Model 401-03 Frame Only

Model 401-01 Leg w/pin

Adjustable 2-Level Scaffold• Strong but lightweight – 35 lbs.• Sets up fast – no braces needed.• Legs adjust for unlevel

ground conditions.• Mason’s platform adjusts from

26" to 50" high.• 1 frame, 2 legs and

2 pig-tail pins equal complete unit.

• Overall width 47-1/2".

Increase Mason’s Production – Reduce Labor Costs on..........Residential – Light commercial.Load bearing walls – Interior partitions.Any wall up to 9' high.

Model 302

30" Plaster and Masonry Stand• Use upright for 30" high stand

or turn on side for 20" height.• All ends capped to keep out dirt

and mortar.• No chain to clog.• Folds flat for storage and handling.• Weight 16 lbs.

Model 301

20" Mortar Board Stand• 1" square tubular steel.• Welded steel tab

eliminates chains.• Folds for storage and handling.• Weight 11 lbs.

34

2036

-35-

10

MASONRY HAND TOOLS

TUCK POINTERS, DURASOFT® HANDLE

• Forged from one piece of high carbon steel.• Resilient DuraSoft® handle provides a soft feel,

reduces fatigue, and offers excellent durability.• High shank and high lift give plenty of hand room.• Tapered for the required sturdiness and correct flexibility.• Integral finger guard protects against

calluses, heat and cold.

EDI Part # UPC# Size Box Case11311 503D 035965013116 6-1/2" x 1/4" 6 611317 506D 035965013178 6-3/4" x 1/2" 6 6

BRICK JOINTER

• Tooled joints are recommended for exterior applications because the jointer compacts the mortar to keep moisture from penetrating the joint.

• Made from one piece of high carbon steel.• Concave joint helps conceal small irregularities

in laying and emphasizes the pattern.• Brick jointers have a convex face for striking concave joints.• Each end is a different size for making different size joints.

EDI Part # UPC# Joint Size Length Box Case15522 80 035965055222 1/2" & 5/8" 10-1/2" 6 72

GRAPEVINE JOINTER, DOUBLE-ENDED

• Forged from high grade tool steel and heat treated.• Straight true bit makes a clean “colonial” joint.• Unique double-ended design gives twice the wear as other.• 8-1/2" length.

EDI Part # UPC# Joint Size Bit Size Box Case15529 84 035965055291 1/2" 1/8" 6 72

GRAPEVINE JOINTER

• Straight true bit makes clean “colonial” joint.• Fitted with a comfortable hardwood handle

and polished ferrule.• 3-1/2" blade length

EDI Part # UPC# Joint Size Bit Size Box Case15535 GJ840 035965055352 1/2" 1/8" 6 6

POINTING TROWEL-WOOD HANDLE

• Forged from a single piece of high carbon steel for unsurpassed strength.

• Hardwood handle

EDI Part # UPC# Size Box Case11128 45 6 035965011280 6" x 2-3/4" 6 6

WIDE LONDON PATTERN BRICK TROWELS, DURASOFT® HANDLE

• Resilient, durable DuraSoft® handle reduces fatigue.

EDI Part # UPC# Size Box Case10152 34 11FG 035965001526 11" x 5-3/4" 2 12

LONDON PATTERN BRICK TROWELS, DURASOFT® HANDLE

• Resilient, durable DuraSoft®

handle reduces fatigue.

EDI Part # UPC# Size Box Case10121 33 10FG 035965001212 10" x 4-5/8" 2 1210123 33 11FG 035965001236 11" x 4-7/8" 2 12

MARGIN TROWELS–WOOD HANDLE

• Forged from a single piece of high carbon steel.• Tempered, ground and polished from toe to heel.• Hardwood handle.

EDI Part # UPC# Size Box Case11202 52 035965012027 5" x 2" 6 611206 56 035965012065 6" x 2" 6 611208 58 035965012089 8" x 2" 6 6

SLED RUNNERS, HALF ROUND / “V” JOINT

• Both ends are turned up for use in either direction.• Heavy gauge steel mounting with DuraSoft® handle.• Half-round specifically designed for finishing

horizontal joints.• “V” pattern provides a line in the center of the

joint to emphasize the joint and conceal small irregularities. Sides are 3/4".• Popular for making half-round sunken or half-round rodded joints.

EDI Part # UPC# Size Box Case16561 611D 035965065610 15" x 1/2" Half Round 6 616565 615D 035965065658 15" x 3/4" ‘V’ 6 6

BRICK HAMMER

• Forged in one piece from high grade steel.• Perfectly balanced and securely fitted with a

comfortable hickory handle.• Designed for breaking, trimming and cleaning brick.• Not intended for striking chisels or metal.

EDI Part # UPC# Weight Length Box Case16560 600 035965065603 16 oz. 11" 4 24

JOINT RAKER

• Large 1-3/4" skate wheels.• Strong aluminum handle is contoured to fit the

hand and squared off at the end.• Hardened nail, adjustable to the proper depth,

can be securely tightened by slipping the nail in the eye of a spade bolt and twisting.

EDI Part # UPC# Size Box Case15502 89 035965055024 8-1/2" x 3" 12 12

JOINT RAKER

• Die-cut from 1/8" steel.• A 5/16" and 3/8" tab at either end rakes corners.

EDI Part # UPC# Size Box Case16193 93 035965061933 N/A 6 72

BLOCK TONGS

• Heavy-duty block tongs designed and built for long wear.

• Can be quickly adjusted to carry from six to ten bricks.

• Tongs are maintenance free.

EDI Part # UPC# Size Box Case16510 88 035965065108 16" 1 12

35

1

2036

-36-

06

MASONRY HAND TOOLS / CONCRETE FINISHING

RUB BRICKS

• Fluted silicon carbide stone.• 20-grit. Ideal for dressing down and removing form

marks from concrete or cleaning brick.

EDI Part # UPC# Size Box Case16440 840 035965064408 6" x 3" x 1" 1 516441 841 035965064415 8" x 3-1/2" x 1-1/2" 1 5

MASONRY BRUSH

• Bristles made of white tampico fiber.• 3-1/2" bristles are set securely in hardwood block.

EDI Part # UPC# Size Box Case16520 829 035965065207 6-1/2" x 2" 1 12

100% BRAIDED NYLON MASON’S LINE

• Made from nylon, size #18.• Will not unravel if struck by a trowel.

Not affected by extreme moisture or dryness.• Won’t mildew, and it stays taut.

EDI Part # UPC# Size Box Case16572 622 035965065726 250' white 1 4816573 623 035965065733 500' white 1 2410841 ML341 035965008419 500' Fl. Lime 1 2410838 ML338 035965008389 500' Fl. Orange 1 24

DURASOFT® HANDLE XTRALITE® FINISHING TROWELS

• Highest grade high carbon spring steel blade.• Aluminum alloy mounting is lightweight but very strong.• Resilient DuraSoft® handle provides a

soft feel, reduces fatigue, and offers excellent durability.

EDI Part # UPC# Size Box Case13207 MX62D 035965032070 12" x 4" 1 1213229 MXS64D 035965032292 14" x 4" 1 1213249 MXS66D 035965032490 16" x 4" 1 1213269 MXS81D 035965032698 18" x 4" 1 6

DURASOFT® HANDLE HIGH CARBON BLUE STEEL XTRALITE® TROWEL

• Highest grade tempered blue spring steel.• Aluminum alloy mounting is lightweight but very strong.• Resilient DuraSoft® handle provides a soft feel,

reduces fatigue and offers excellent durability.

EDI Part # UPC# Size Box Case13241 MXS57BD 035965032414 14" x 3" 1 12

DURASOFT® HANDLE PERMASHAPE® “BROKEN-IN” FINISHING TROWELS

• Highest grade high carbon spring steel.• Aluminum alloy mounting is lightweight but very strong.• PermaShape® process helps maintain

original broken-in shape.• Resilient DuraSoft® handle provides a soft feel,

reduces fatigue, and offers excellent durability.• Broken-in shape eliminates line and ripple marks right from the start.• Beveled work edges prevent surface aggregate popping.• Beginning finishers can do a better job and be more productive sooner.

EDI Part # UPC# Size Box Case13230 PB64D 035965032308 14" x 4" 1 1213247 PB66D 035965032476 16" x 4" 1 12

DURASOFT® HANDLE PERMASHAPE® “BROKEN-IN” GOLDEN STAINLESS XTRALITE® TROWELS

• Made from the highest grade stainless steel properly shaped and tempered to a golden finish.

• Resilient DuraSoft® handle provides a soft feel, reduces fatigue, and offers excellent durability.

• Aluminum alloy mounting is lightweight but very strong.• PermaShape® process helps maintain original broken-in shape.• Broken-in shape eliminates line and ripple marks right from the start.• Beveled work edges prevent surface aggregate popping.• Beginning finishers can do a better job and be more productive sooner.

EDI Part # UPC# Size Box Case13413 PB145GSD 035965034135 14" x 5" 1 1213439 PB165GSD 035965034395 16" x 5" 1 6

DURASOFT® HANDLE ROUNDED FRONT END XTRALITE® TROWEL

• Made from the highest grade spring steel, properly shaped and tempered.

• Aluminum alloy mounting is lightweight but very strong.• Resilient DuraSoft® handle provides a soft feel,

reduces fatigue, and offers excellent durability.

EDI Part # UPC# Size Box Case13511 MXS66RED 035965035118 16" x 4" 1 12

CURB TOOL

• Made of heavy gauge stainless steel.• 104° blade angle.• Resilient DuraSoft® handle.

EDI Part # UPC# Size Radius Box Case14270 4270D 035965042703 6" x 5" x 3-1/2" 2" 4 4

STAINLESS STEEL SAFETY STEP GROOVER

• Edges are angled up to use against a guide.• Used to cut six grooves, 3/4" apart, 1/4" deep.• Creates a safety tread effect on steps.• Cuts a groove with 1/8" radius.• Resilient DuraSoft® handle.

EDI Part # UPC# Size Box Case14282 4282D 035965042826 6" x 6" 6 6

HEAVY-DUTY ZINC HAND EDGER

• Made from high quality, long wearing zinc. • Resilient DuraSoft® handle.• Smooth finish allows for easier clean-up.• Dimensionally more consistent than bronze.• Longer lasting and heavier than steel edger.

EDI Part # UPC# Size Radius Lip Box Case14154 4154D 035965041546 6" x 2-3/16" 1/4" 5/8" 6 6

STRAIGHT END STEEL CONCRETE EDGER

• Made from carbon steel, with a sturdy mounting welded to the blade. Resilient DuraSoft® handle.

• Used to produce a radius at the edge of a concrete slab to help prevent the edge from chipping.

EDI Part # UPC# Size Radius Lip Box Case14152 120D 035965041522 8" x 6" 3/8" 1/2" 6 6

36

2036

-37-

10

CONCRETE FINISHING TOOLS

WOOD HANDLE

• Wood handles are fitted with a steel clevis.• For use with tools with a clevis-style bracket.

EDI Part # UPC# Size Diameter Box Case14842 10 035965048422 6' 1-1/2" 1 6

HEAVY-DUTY ZINC WALKING EDGER

• Made from high quality, long wearing zinc.• Dimensionally more consistent than bronze.• Longer lasting and heavier than steel edgers.• Use with our #10 handle.• Curved up at both ends for easy push/pull motion from either direction.• Helps eliminate bending when edging large areas of concrete.

EDI Part # UPC# Size Radius Lip Box Case14012 4012 035965040129 9" x 4" 1/4" 5/8" 1 1

CURVED END STEEL CONCRETE EDGER

• Curved ends help prevent edger from digging into wet concrete.• Made from carbon steel, with a sturdy mounting welded

to the blade. Resilient DuraSoft® handle.• Used to produce a radius at the edge of a concrete

slab to prevent chipping.

EDI Part # UPC# Size Radius Lip Box Case14146 136D 035965041461 6" x 3" 3/8" 1/2" 6 24

STAINLESS STEEL CONCRETE EDGERS

• Straight ends.

EDI Part # UPC# Size Radius Lip Box Case13918 CE519S 035965039185 8" x 4" 1/2" 5/8" 1 613920 CE520S 035965039208 8" x 4" 3/4" 7/8" 1 6

STAINLESS STEEL GROOVER

• Blade made of stainless steel. Resilient DuraSoft® handle.• Has a sturdy steel mounting.• Properly shaped bit and leading edge cut a sharp groove.• Radius of 1/4", width is 1/2", and depth is 1/2".


BLUE STEEL EDGER

• Straight ends.

EDI Part # UPC# Size Radius Lip Box Case13957 CE546B 035965039574 9" x 6" 3/8" 1/2" 1 12

CONCRETE EDGER

• Has a steel blade, steel mounting and mortised wood handle.• Both ends are slightly curved for working ease.• Used to produce a radius at the edge of a concrete slab

to help prevent the end from chipping off.

EDI Part # UPC# Size Radius Box Case16492 92 035965064927 6" x 2-3/4" 3/8 12 60

HEAVY-DUTY ZINC HAND GROOVERS

• Made from high quality long wearing zinc.• Smooth finish allows for easier clean-up.• Finely finished to cut sharp clean grooves.• Dimensionally more consistent than bronze.• Resilient DuraSoft® handle.

EDI Part # UPC# Size Radius Width Depth Box Case14105 833D 035965041058 6" x 4-3/8" 1/4" 3/8" 1/2" 1 614106 834D 035965041065 6" x 4-3/8" 1/4" 3/8" 3/4" 1 614107 835D 035965041072 6" x 4-3/8" 1/4" 3/8" 1" 1 6

HEAVY-DUTY ZINC WALKING GROOVER

• Made from high quality, long wearing zinc, harder than bronze.• Dimensionally more consistent than bronze.• Has the weight and finish to cut quickly and cleanly.• For use with our #10 handle.• Radius is 1/4".• Both ends turned up so it can be used in either direction.• Helps eliminate bending when working large areas of concrete.

EDI Part # UPC# Size Width Depth Box Case14108 836 035965041089 8" x 4-3/8" 3/8" 1" 1 12

BULL FLOAT GROOVER ATTACHMENT

• Made from durable hardened aluminum.• Slide easily over any magnesium bull float to

give the ability to form grooves or expansion joints.• Two thumbscrews are used to tighten the

attachment to the bull float.• Can also be used in combination to form

multiple grooves.

EDI Part # UPC# Radius Width Depth Box Case14712 4712 035965047128 1/4" 3/4" 1" 1 1

“BROKEN-IN” MAGNESIUM HAND FLOATS

• Pre-shaped across length and width of blade.• Front and back of blade won’t dig in, while sides

glide over surface.• Extruded from very hard, durable,

lightweight magnesium.• DuraSoft® handles are secured with torque pad screws that will not back out.• Assist the user in preparing the surface for troweling.• If a float (rough) finish is desired, floating is the final operation.• Recommended for use with air entrained concrete.• Magnesium floats produce a smoother finish than wood.• DuraSoft® handle, provides a soft feel, reduces fatigue, and offers excellent durability.

EDI Part # UPC# Size Box Case14617 Bl145D 035965046176 16" x 3-1/8" 6 614619 Bl146D 035965046190 20" x 3-1/8" 6 6

ROUND END MAGNESIUM FLOAT

• Extruded from very hard, durable, lightweight magnesium.

• Comfortable handle is positioned to give the tool perfect balance.

• Handles are secured with torque pad screws that will not back out.

• Assists the user in preparing the surface for troweling.• If a float (rough) finish is desired, floating is the final operation.• Magnesium floats produce a smoother finish than wood.• Fully rounded ends help prevent float marks.

EDI Part # UPC# Size Box Case14612 143D 035965046121 16" x 3-1/8" 6 6

37

1

2036

-38-

10

CONCRETE FINISHING TOOLS

CAST MAGNESIUM FLOAT

• Cast from the finest magnesium.• Placement of the handle gives the float perfect balance.• Designed with just the right broken-in shape.• Cast construction allows more knuckle clearance.• Handles are secured with torque pad screws that will not back out.


MAGNESIUM BULL FLOAT

• Made from the finest extruded magnesium available.• Square ends.• Comes with complete bracket assembly.• No other heavy-duty float outlasts this one.• Lightweight, long wearing and properly balanced to provide the finish you want.• Using several handle sections, the finisher can float a slab well beyond normal reach.

EDI Part # UPC# Size Box Case14704 B48 035965047043 48" x 8" 1 1

CHANNEL BULL FLOAT

• Using several handle sections, the finisher canfloat a slab well beyond his reach.

EDI Part # UPC# Size Box Case14729 CB60 035965047296 60" x 6" 1 1

ROUND END BULL FLOATS

• The round ends help eliminate finishing marks.• Made from the finest extruded magnesium alloy available.• Lightweight, long wearing and properly

balanced to provide the finish you want.• B48FR and B72FR come with complete

bracket assembly.

EDI Part # UPC# Size Box Case14720 B48FR 035965047203 48" x 8" 1 114721 B48FRB 035965047210 48" x 8" Blade Only 3 314741 B72FR 035965047418 72" x 8" 1 1

MAGNESIUM BULL FLOATS

• Extruded from magnesium alloy.• Lightweight, long wearing.• Comes with bracket assembly.

EDI Part # UPC# Size Box Case13865 MB42 035965038652 42" x 8" 1 113874 MB48 035965038744 48" x 8" 1 1

FRESNO TROWEL

• Comes with an all-angle swivel attachment.

EDI Part # UPC# Size Box Case13871 FR36R 035965038713 36" x 5" 1 6

CONCRETE BROOM• Long wearing 3" black polypropylene bristles

set solidly into a natural lacquered hardwood block • Threaded hole accepts any standard broom handle.• Ideal for applying non-slip finish to newly

finished concrete surfaces.


BLUE GLIDER

• Made of blue spring steel.• Round ends.• A c-channel runs the length of the glider to help

strengthen the blade.• Included with the gliders is a hardware package

that contains two bolts, two nuts, two lock washers and two flat washers.• Can be used with #RL6 RotaLeveler® or #AB4 AutoJust®.

EDI Part # UPC# Size Box Case13989 BG72 035965039895 72" x 12-3/8" 1 1

ROTALEVELER® BULL FLOAT BRACKET

• Fits any bull float without adapters.• Features easy control adjustment, smooth operation,

and a large protected grease reservoir.• Accepts most 1-3/4" and 1-3/8" push button handles

without adapters.• Easier to keep clean than most competitors’ units.

EDI Part # UPC# Size Box Case14801 RL6 035965048019 N/A 1 1

ALUMINUM HANDLE SECTIONS

• Lightweight, yet rigid tubular design.• The large thread can be combined with similar

handles made by others.• Warning: When using handle extensions,

always avoid contact with electrical power lines or any electrical source.

EDI Part # UPC# Size Diameter Box Case14804 B5 72 035965048040 6' 1-3/4" 6 6

PUSH BUTTON HANDLE SECTIONS

• Spring loaded button-type aluminum sections snap together quickly.

• Will not loosen during use.• Anodized.• Can be adapted for use with bull floats and other

construction tools requiring a long handle.• Warning: When using handle extensions, always avoid contact with electrical power

lines or any electrical source.

EDI Part # UPC# Size Diameter Box Case14807 PB72L 035965048071 6" 1-3/4"" 6 6

HORSEHAIR BROOM

• Features fine grey horsehair bristles.• Bristles are set in a hardwood block.• Used to apply a light texture while

finishing concrete.


ROUND HOLE CONCRETE TAMPER

• Reinforced round hole grill.• Built to take the pounding and stay flat.• Properly balanced handle with rubber grips

to ensure easy, safe handling.

EDI Part # UPC# Size Box Case14722 T48 035965047227 48" x 6-1/2" 1 1

38

2036

-39-

10

HAND TOOLS

PUSH BUTTON ADAPTER

• Features a threaded male end.• Modifies push button handle sections for use

with tools which require a threaded end; such as bull floats, concrete brooms and other tools.

• Can be used with our #PB72 handle and similar ones made by others.

EDI Part # UPC# Size Diameter Box Case14810 BF8 035965048101 9" 1-3/8"" 1 50

PUSH BUTTON HANDLE ADAPTERS

• Fits 1-3/8" and 1-3/4" push button handles.• Used with bull floats, fresnos, brooms, etc.

EDI Part # UPC# Description Box Case14819 4819 035965048194 Male Thread 1 614820 4820 035965048200 Female Thread 1 6

FRESNO ADAPTER

• Rugged aluminum casting.• Designed specifically to connect standard threaded handle

sections to a fresno, walking edger or groover, or any other tools that are equipped with similar attachment devices.

• Unique “wrench-flats” feature makes it easy to remove.


METAL SCREEDS

• Made from metal alloy, won’t rust or rot.• Ends capped to prevent concrete from getting inside.• Lightweight, long wearing and rigid.• Warning: When using screeds always avoid

contact with electrical power lines or any electrical source.

EDI Part # UPC# Size Box Case14746 4746 035965047463 6' x 1" x 4" 2 214752 4752 035965047524 8' x 2" x 4" 1 114723 822 035965047234 12' x 2" x 4" 1 114724 824 035965047241 14' x 2" x 4" 1 114735 4735 035965047357 16' x 1-1/2" x 3-1/2" 1 1

HIGH STRENGTH SCREEDS

• Premium high strength alloy, won’t rust or rot; more damage and warp resistant.

• End capped to prevent concrete from getting inside.• Lightweight, long wearing and rigid.• Length available in 6' - 24'.• Warning: When using handle extensions,

always avoid contact with electrical power lines or any electrical source.

EDI Part # UPC# Size Box Case14770 14770 035965047708 8' x 1-1/2" x 3-1/2" 1 114772 14772 035965047722 12' x 1-1/2" x 3-1/2" 1 114773 14773 035965047739 14' x 1-1/2" x 3-1/2" 1 114775 14775 035965047753 16' x 1-1/2" x 3-1/2" 1 114776 14776 035965047760 20' x 1-1/2" x 3-1/2" 1 114786 14786 035965047869 10' x 2" x 4" 1 114788 14788 035965047883 12' x 2" x 4" 1 1

STEEL SPRED-KRETE

• Blade of 12-gauge cold rolled steel.• Sturdy steel ferrule is welded securely to

the blade and holds the contoured handlefirmly in place.

• Superior to a jam type connector.

EDI Part # UPC# Size Box Case14726 826 035965047265 20" x 4" w/hook 6 6

MAGNESIUM ASPHALT LUTE

• Lightweight T section blade has blunt teeth which are designed to allow material to pass through without catching.

• Rugged formed steel pole connector prevents breakage and ensures rigidity.

• Handle sold separately.


ALUMINUM ASPHALT LUTE HANDLE

• Made of seamless aluminum alloy tubing for lightness and strength.

• For use with our #838 magnesiumasphalt lute.

EDI Part # UPC# Size Diameter Box Case16439 839 035965064392 6' 1-1/4" 1 12

RESIN FLOAT

• Made from 3/8" thick laminated canvas resin.• Extremely dense.• Works the slab like a wood float but it lasts

many times longer.• Resilient DuraSoft® handle.


WOOD FLOATS

• Made from 1/2" thick seasoned mahogany.• Have a very smooth finish.

EDI Part # UPC# Size Box Case14512 WF943 035965045124 12" x 3-1/2" 1 2414518 WF947 035965045186 18" x 3-1/2" 1 24

SCRATCHER TROWEL

• Blade made of the highest grade spring steel.• Aluminum alloy mounting fitted with a curved handle.• Blade is notched on three sides - 1/2 x 15/32 ‘V’.• Used for scoring plaster or stucco to form a good

bond between coats.• Resilient DuraSoft® handle provides a soft feel,

reduces fatigue, and offers excellent durability.

EDI Part # UPC# Size Box Case15650 714SD 035965056502 16" x 4-1/2" 4 4

39

1

2036

-40-

10

HAND TOOLS

REBAR BENDER/CUTTER

• Cuts and bends rebar up to 5/8" diameter.• Mounted on wood board.• Rugged cast iron construction.• 54" steel handle.

EDI Part # UPC# Size Box Case14730 14730 035965047302 66" x 7-1/2" 1 1

DURASOFT® II BLUE STEEL TAPING KNIFE

• Premium tempered blue steel blade with rigid alloy backer.

• Blade is tapered so you can run corners faster and easier.

• Narrow profile DuraSoft® handle moves hand forward to help improve blade control.

• Ergonomic contours for improved comfort.• One of the most lightweight knives on the market.


DURASOFT® HANDLE PUTTY AND JOINT KNIVES

• Blade of high carbon steel, tempered then polished to a mirror finish.

• Full length tang goes through the resilient DuraSoft® handle.

• 9-in-1 Paint Tool can be used as: a scraper, spreader, roller cleaner, crack cleaner, paint can opener and closer, nail puller, concave and convex scraper.

EDI Part # UPC# Description Box Case16697 PK200FD 035965066976 2" Flex Putty Knife 6 2416711 JK400FD 035965067119 4" Joint Knife 6 2416717 PT901D 035965067171 9-in-1 Paint Tool 6 24

HELI - ARC MUD PAN

• Made from heavy gauge stainless steel.• Corners are heli-arc welded to form smooth,

seamless inside corners that leave no place for the mud to collect.


RUBBER FLOATS

• Has a 5/8" thick red rubber pad specially bonded tothe aluminum backing plate for long wear.

• Frequently used by plasterers and other finishers for rough and/or textured finishes.

• Available with a fine or a coarse pad.

EDI Part # UPC# Size Box Case14404 38 035965044042 9" x 4" - Fine 1 2414406 39 035965044066 9" x 4" - Coarse 1 24

DURANOTCH™ TROWELS

• DuraNotch™ teeth are hard chrome plated for extra wear sothey keep their shape longer than regular notched trowels.

• Tempered steel blade.• Cast aluminum mounting.• Blade size is 11 x 4-1/2.

EDI Part # UPC# Size Notch Style Box Case15848 716SDDN 035965058483 1/4" x 3/8" x 1/4" ‘U’ 1 1215846 775SDDN 035965058469 1/2" x 1/2" x 1/2" SQ 1 1215842 780SDDN 035965058421 1/4" x 3/16" ‘V’ 1 12

CRESCENT® TILE NIPPERS, FORMERLY DIAMOND®

• 5/8" jaws with carbide tips.• Unique plastic grip handle design for added comfort.• Handle stops to protect tips.• Center spring returns jaws to open position.• Warning: Always wear safety goggles

when using tile nippers.

EDI Part # UPC# Size Box Case15350 GT28C 043127150289 N/A 1 1

CHALK

• 8 oz. refill bottles.

EDI Part # UPC# Color Box Case15426 64901 024721500076 Blue 6 2415424 64902 024721500120 Red 6 24

CHALK BOX

• Aluminum housing.• Easy-to-hold, sure-grip shape.• Easy to fill by simply sliding the nylon cover open.• Self-locking handle and plated anchor ring.• Cotton line is highly absorbent for positive

marking, and is replaceable.• Can also be used as a plumb bob.

EDI Part # UPC# Size Box Case15422 64110 024721500069 100' 6 6

CANVAS TOOL BAG

• Made of heavy-duty canvas with lock stitched seams.• Waterproof masonite bottom with four metal studs.• Built on a 12-gauge steel frame.• Handles, billets and buckles are riveted to frame.• Inside pocket to prevent small tools from being lost.

EDI Part # UPC# Size Box Case16431 831 035965064316 20" x 15" 1 12

NEOLITE KNEE PADS

• Tough construction to stand up under hard wear.• Neolite pads are felt lined and shaped to fit your knee.• One leather strap holds them in place.• Strap will not slip or bind.


HEAVY-DUTY FITTED KNEE PADS

• Cordura nylon fabric with a large, non-marring plastic cap.

• Contour fitted.• Offer improved weight distribution and

better protection.• Have wide Velcro® straps.• Heavy pad provides maximum protection.• Water and abrasion resistant.

EDI Part # UPC# Size Box Case16448 KP48 035965164481 N/A 1 12

40

63

Hydraulic CuttersElectric Cutters

Gas CuttersPower Packs

Concrete SawsAbrasive Wheels

Grinding DiscsCore Drill Rigs

Diamond Core BitsWire Saws

Saw BladesRing Saw Blades & Chains

Chainsaws

Hydraulic Power UnitsHydraulic Pumps

Hydraulic BreakersHydraulic Hammers

Air CompressorsTampers & Chippers

Rock DrillsPower ToolsCarbide Bits

Concrete Cutting & Demolition 3

Tamco, Inc.

1067

-23-

10

POWER CUTTERS

The Husqvarna K750 has a modern, compact appearance. To make operation even easier it features a larger front handle providing a more comfortable grip.

K750

64

Blade sold separately.

TECHNICAL SPECIFICATIONSEngine Air-cooled 2 stroke engineDisplacement 74 ccPower - hp (kW) 5 (3.7)Maximum RPM (no load) 5,400Fuel capacity - qt. (l) .95 (.9)Blade diameter - in. (mm) 12/14 (300/350)Cutting depth - in. (mm) 4/5 (100/127)Weight w/o fuel and cutting equip. - lbs. (kg) 21.8 (9.7) K750

OilGuard is a synthetic blend designed for power cutters and any other 2-cycle equipment used in tough, dirty conditions. OilGuard oil lowersengine operating temperatures and reduces smoke. OilGuard’s unique yellow color is used to regulate Husqvarna’s patented OilGuard system inselected power cutter models to eliminate piston and cylinder failurescaused by lack of lubrication.

Applications:

• Cuts concrete and masonry in alteration, renovation and newconstruction work.

• Cuts smaller holes and adjusts window and door openings.

• Cuts curbstones and pavers in landscaping.

• Pipe cutting in installation work.

• Asphalt cutting in roadwork and pre-cutting in pipe trenches.

• Metal cutting.

Benefits:

• Prevents engine failures from raw gas or improper mixing.

• OilGuard is a quality oil developed specifically for dusty environments like construction sites.

• Oil Guard oil is ideal for all air-cooled two-stroke engines.

• You can use standard two-stroke oil in a K750 OilGuard machine;simply pull out the OilGuard button by the rear handle.

K750 OilGuard


K750 12" K750 14"Item no. 965141901 965142201

Applications:

• Cuts concrete and masonry in alteration, renovation and new con-struction work.

• Cuts smaller holes and adjusts window and door openings.

• Cuts curbstones and pavers in landscaping.

• Pipe cutting in installation work.

• Asphalt cutting in roadwork and pre-cutting in pipe trenches.

• Metal cutting.

Benefits:

• Active Air Filtration, centrifugal air cleaning in three stages, forextended product life and longer service intervals.

• Engine with X-Torq produces more power, higher torque and 70%fewer emissions.

• SmartCarb, built-in automatic filter compensation, maintains highpower and lowers fuel consumption.

• DuraStarter, the dust-sealed starter, and the durable starter cordreduce the risk of downtime and increase reliability and service life.

TECHNICAL SPECIFICATIONSEngine Air-cooled 2 stroke engineDisplacement 74 ccPower - hp (kW) 5 (3.7)Maximum RPM (no load) 5,400Fuel capacity - qt. (l) .95 (.9)Blade diameter - in. (mm) 12/14 (300/350)Cutting depth - in. (mm) 4/5 (100/127)Weight w/o fuel and cutting equip. - lbs. (kg) 21.4, (9.7) K750 OilGuard

K750 OilGuard 12" K750 Oil Guard 14"Item no. 965180901 965181201

1067

-24-

10

POWER CUTTERS

Applications:

• Cuts holes in alteration, renovation and new construction work.

• Adjustment of window and door openings.

• Pipe cutting for installation work.

Benefits:

• Cutting depth of 10", twice the depth of a traditional power cutter.

• Active Air Filtration™, centrifugal air cleaning in three stages, extendsproduct life and service intervals.

• Engine with X-Torq® produces more power, higher torque and greatlyreduced emissions.

• SmartCarb™, a built-in automatic filter compensation, maintains highpower and lowers fuel consumption.

• EasyStart™ provides 50% easier starts.

• DuraStarter™, a dust-sealed starter, and the durable starter cord reducethe risk of downtime and increase reliability and service life.

• The Poly V-belt provides better power transmission, less retensioningand increased product life.

• Efficient vibration and sound dampening make the machine more convenient to use.

K 960 Ring

65


TECHNICAL SPECIFICATIONS K 960 RingItem no. 966851601Engine Air-cooled 2 stroke engineDisplacement cu. in. (cc) 5.7 (94)Maximum horsepower - hp (kW) 6.1 (4.5)Ring blade diameter - in. (mm) 14 (350)Cutting depth - in. (mm) 10 (260)Weight w/o fuel and cutting equip. - lbs. (kg) 28.8 (13.1)

Item No.PXR 45 (Blue) 531100739ELR 20 (Yellow) 531108058ELR 45 (Blue) 531108059ELR 70 (Blue-Red) 531100708SLR 45 (Blue) 531100745ELR 20 (Yellow) .220" wide 531101098Ringblade II 531156042All ring blades include a drive disk.

Applications:

• Perfect for small and irregularly shaped openings.

• An excellent complement to a wall saw, it helps avoid overcutting at the corners.

• Cuts small holes and adjusts window and door openings.

Benefits:

• Make up to 15" deep cuts from one side.

• Active Air Filtration™, centrifugal air cleaning in three stages, extendsproduct life and service intervals.

• Engine with X-Torq® produces more power, higher torque and greatlyreduced emissions.

• SmartCarb™, a built-in automatic filter compensation, maintains highpower and lowers fuel consumption.

• DuraStarter™, a dust-sealed starter, and the durable starter cord reducethe risk of downtime and increase reliability and service life.

• Efficient vibration and sound dampening.

K 960 Chain

14" bar included.Chain sold separately.

We have developed a special series of dia-mond chains for the K960 Chain. They areavailable in a variety of hardnesses, for dif-ferent types of cuttings jobs, and aredesigned for high-power, tough operation.Fitting the saw bar and chain is easy, and thechain is tensioned without any tools.

TECHNICAL SPECIFICATIONS K 960 ChainItem no. 966850602Engine Air-cooled 2 stroke engineDisplacement cu. in. (cc) 5.7 (94)Power - hp (kW) 6.1 (4.5)Bar - in. (mm) 14 (350)Cutting depth - in. (mm) 15 (381)Weight w/o fuel and cutting equip. - lbs. (kg) 20.7 (9.4)

Ring Saw Blades

Item No.PXC 45 531101185ELC 45 531101187ELC 70 531101186SLC 45 53110118414" bar 506346214

Diamond Chains Feature: Fast cutting with depths to 15"; 32 segments/ 64 drive linksTotal segment height: .200" diamond depth

Feature: Fast cutting with depths to 10"Total segment height: .200" diamond depth

3

1067

-25-

10

POWER CUTTERS / POWER PACKS

Applications:

• For cutting indoors and outdoors.

• Ideal for quick and easy cutting of building block, pipe,reinforcement bar, supports, etc.

• Easily adjusts between cutting different materials.

Benefits:

• One of the market’s most powerful and versatile electricpower cutters.

• Considerable distance between handles for safe controland reduced load.

• Elgard™, the advanced electronic overload protectionsystem, varies the rotation speed to warn of anapproaching overload.

• Electronic Softstart™ provides starting with normal,slow-acting fuses.

• Quick-locking of the spindle and a large outlet in theblade guard simplifies blade changes.

• Generously dimensioned miter gear provides highdurability, minimal power loss and low noise levels.

K 3000 Electric / K 3000 Wet

66


Hydraulic Power Pack PP 418

Electro-Hydraulic Power Pack PP 325 E

• This simple and efficient, yet versatile, cart-mounted power packincludes a tubular frame which protects components.

• The PP 325 E can be easily transported and operated by one person.

Applications:

• Can power any hydraulic tool requiring 5,8 or 10 gpm flow at 2,000 psi.

• Ideally suited to provide power forHusqvarna K2500 power cutter, K3600MK II ring saw and other power cutters.

• Power for Husqvarna DM 406 H andother core drills.

• Perfect for diamond chain saws.• Use with Husqvarna WS 325 and other

small wall saws.

• Also for breakers, tampers, drivers, chippers, drills, earth augers and more.

Benefits:

• Unique hydrostatic pump system doesnot use engine rpm to regulate flow, providing more consistent and accurateflow at 5, 8 and 10 gpm.

• Electronic engine controller maintainsconstant engine speed under load toensure maximum power at all flow settings.

• Automatic power-on-demand saves fuel and has a five second delay forsmoother tool operation during intermittent cutting conditions.

K 3000 Electric

TECHNICAL SPECIFICATIONS K 3000 ELECTRIC 12 K 3000 ELECTRIC 14 K 3000 WET 14Item no. 968375401 968376401 968378401Electric motor - volt 120 120 120Rated output - watt 1,800 1,800 1,800 Blade diameter - in. (mm) 12 (305) 14 (350) 14 (350)Cutting depth - in. (mm) 4 (100) 5 (127) 5 (127)Weight without blades - lbs. (kg) 16.3 (7.4) 16.8 (7.6) 17.4 (7.9)

TECHNICAL SPECIFICATIONS PP 418 PP 325 EItem no. 966947201 965156406Engine/motor Gas twin cylinder OHV, air-cooled electric start ElectricSpecifications Briggs & Stratton 480V, 16 amp, 60 Hz, 3 PHPressure - psi (bar) 2,000 (140) 2,000 (140)Flow - gal./min. 5, 8, 10 10

(l/min.) (20, 30, 40) (40)Output - hp (kW) 18 (13.5) 12.5 (9)Weight including oil - lbs. (kg) 298 (135) 205 (93)

1067

-18-

10

CONCRETE SAW

The FS 6600 D 3-speed gearbox saw is a professional saw for large andmid-size jobs. The addition of the 3-speed gearbox extends the range ofapplications for an already versatile and powerful production saw.

Applications:

• Large jobs such as airports, highways, larger service workand other applications where production is a concern.

• Ideal for mid-size and smaller jobs that require highproduction rates.

Benefits:• Tier 3/Interim Tier 4 emissions compliant.

• The FS 6600 D 3-speed gearbox is one of the mostpowerful flat saws in its range.

• Patented power transmission system transmits morepower to the bladeshaft (60 hp) with optimum torque.

• Bladeshaft tachometer helps operator identify correctbladeshaft rpm for selected blade size.

• Optional electric tracking system allows operator tomake tracking adjustments with a touch of a switchwhile cutting.

• Patented IntelliSeal bladeshaft system allows for aminimum 500-hour service interval and eliminates dailygreasing of bearings.

• Patented variable positioning handlebars easily adjustto individual operator's preference which increasesoperator comfort and reduces operator fatigue.

FS 6600 D 3-Speed Gearbox

67

TECHNICAL SPECIFICATIONS FS 6600 D 3 SP 26 FS 6600 D 3 SP 30 FS 6600 D 3 SP 36 FS 6600 D 3 SP 42Front pivot item no. 965885419 965885421 965885423 965885425Front pivot electric tracking item no. 965885420 965885422 965885424 965885426Maximum blade diameter, in. (mm) 26 (660) 30 (762) 36 (914) 42 (1,067)Maximum depth of cut, in. (mm) 10-1/2 (267) 12 (305) 15 (381) 17-1/2 (445)Average bladeshaft, rpm 3,070/2,160/1,860 2,670/1,880/1,610 2,300/1,620/1,390 1,620/1,390/1,180Blade range, in. (mm) 14/18/26 (350/450/660) 18/26/30 (450/660/762) 20/30/36 (508/762/914) 30/36/42 (762/914/1,067)Blade flanges, in. (mm) 5 (127) 5 (127) 6 (152) 7 (178)Power at bladeshaft, hp 60Arbor size, in. (mm) 1 (25.4), single drive pinBladeshaft diameter, in. (mm) 2 (51)Axle front/rear, in. (mm) 1 (25.4)/4-bolt hub mountWheels front, in. (mm) 8 x 3 (203 x 76)Wheels rear, in. (mm) 10 x 3 (254 x 76)Handlebar adjustment Variable positioningTransmission type Dual motor hydrostatic driveTransmission speeds, fpm 0 - 300Electric tracking (optional) Electric switch operatedBlade guard type Slip-on Bolt-onNumber of belts 16 (4 each 4 band 3VX)Blade depth control Electrohydraulic raise and lowerMaximum weight uncrated, lbs. (kg) 1,871 (849) 1,892 (858) 1,948 (884) 2,013 (869)Maximum weight crated, lbs. (kg) 1,968 (893) 1,989 (902) 2,020 (916) 2,045 (297)Dimensions uncrated, in (mm) LxWxH 67 x 38 x 57 (1,701 x 965 x 1,448)

Power source..........................................................DieselEngine ............................................................John DeereSpecifications.................................................4024HF295Horsepower..................................................................66Displacement - cu. in. (l) ................................146.5 (2.4)Bore/stroke - in. (mm)...................3.39 (86) / 4.13 (105)Cylinders/stroke ..........................................................4/4Fuel capacity - gal. (l) ........................................9.75 (37)Oil Capacity - qt. (l) .............................................8.45 (8)Air filter.......................................Dual element radial sealStarter...................................................................ElectricEngine cooling...................................................Liquid/air


3

1067

-19-

10

CONCRETE SAW

The FS 4800 D 3-speed gearbox saw is a professional saw for large andmid-size jobs. The addition of the 3-speed gearbox extends the range ofapplications for an already versatile and powerful mid-range saw.

Applications:

• For jobs such as airports, highways, service work andother applications where production is a concern.

• Ideal for mid-size to small jobs that require highproduction rates when cutting depth is no more than 15".

Benefits:

• Tier 3/Interim Tier 4 emissions compliant.

• The FS 4800 D 3-speed gearbox is one of the mostpowerful flat saws in its range.

• Patented power transmission system transmits more powerto the bladeshaft (42 hp) with optimum torque.

• Bladeshaft tachometer helps operator identify correctbladeshaft rpm for selected blade size.

• Front pivot model has an optional electric tracking system thatallows the operator to make tracking adjustments with a touch ofa switch while cutting.

• Rear pivot model is recommended when maneuverability is key forroad repair and service work.

• Patented IntelliSeal bladeshaft system allows for a minimum of 500-hour service interval and eliminates daily greasing of bearings.

FS 4800 D 3-Speed Gearbox

68

TECHNICAL SPECIFICATIONS FS 4800 D 3 SP 26 FS 4800 D 3 SP 30 FS 4800 D 3 SP 36Front pivot item no. 965165237 965165227 965165229Front pivot, electric tracking item no. 965165226 965165228 965165230Rear pivot item no. 965165235Maximum blade diameter, in. (mm) 26 (660) 30 (762) 36 (914)Maximum depth of cut, in. (mm) 10-1/2 (267) 12 (305) 15 (381)Average bladeshaft, rpm 3,100/2,180/1,870 2,660/1,800/1,570 2,260/1,580/1,360Blade range, in. (mm) 14/18/26 (350/450/650) 18/26/30 (450/650/750) 20/30/36 (500/750/900)Blade flanges, in. (mm) 5 (127) 5 (127) 6 (152)Power at bladeshaft, hp 42Arbor size, in. (mm) 1 (25.4), single drive pinBladeshaft diameter, in. (mm) 2 (51)Axle front/rear, in. (mm) 1 (25.4)/4-bolt hub mountWheels front, in. (mm) 6 x 2 (152 x 51)Wheels rear, in. (mm) 10 x 3 (254 x 76)Handlebar adjustment Variable positioningTransmission type Dual motor hydrostatic driveTransmission speeds, rear pivot, fpm 0 - 200 differential locked, 0 - 100 unlockedTransmission speeds, front pivot, fpm 0 - 200 differential lockedElectric tracking (optional) Electric switch operatedBlade guard type Slip-onNumber of belts 12 (4 each 3 band 3VX)Blade depth control Electrohydraulic raise and lowerMaximum weight uncrated, lbs. (kg) 1,420 (644) 1,440 (653) 1,460 (662)Maximum weight crated, lbs. (kg) 1,493 (677) 1,513 (694) 1,533 (695)Dimensions uncrated, in (mm) LxWxH 56 x 33-1/4 x 51 (1,422 x 845 x 1,295)

Power source..........................................................DieselEngine ..................................................................YanmarSpecifications ......................................................4TNV88Horsepower..................................................................48Displacement - cu. in. (l) .................................133 (2.19)Bore/stroke - in. (mm).....................3.46 (88) / 3.54 (90)Cylinders/stroke ..........................................................4/4Fuel capacity - gal. (l) .......................................7.8 (29.5)Oil Capacity - qt. (l) ............................................7.8 (7.4)Air filter.......................................Dual element radial sealStarter...................................................................ElectricEngine cooling...................................................Liquid/air


1067

-20-

10

CONCRETE SAW

The Husqvarna FS 400 is a robust, convenient all-around flat saw. The adjustable handle ensures low vibrations and an ergonomic workingposition. Perfect weight distribution means excellent stability while sawing. Ideal for small jobs.

Applications:

• Ideal for small road repair jobs in concrete or asphalt.

• Cutting trenches for pipe laying.

• Making expansion joints in concrete floors.

• Cutting channels for impedance loop fittings or cable laying.

Benefits:

• Productive saw with excellent weight distribution and stability.

• Adjustable, low-vibration handlebar for operator comfort.

• Patented gas-assisted raise/lower system.

• Easy to transport and lift.

• Optimum power transmission to the blade due to the Poly V-belt.

• Large integrated water tank is standard.

FS 400

69

TECHNICAL SPECIFICATIONS FS 400 Item no. 965148208Maximum blade diameter, in. (mm) 18 (450)Maximum depth of cut, in. (mm) 6-5/8 (168)Average bladeshaft, rpm 2,800Blade flanges, in, (mm) 4-1/2 (114)Arbor size, in. (mm) 1 (25.4), drive pinBladeshaft diameter, in. (mm) 13/16 (21.5)Axle front/rear, in. (mm) 3/4 (19)/3/4 (19)Wheels front, in. (mm) 5 x 1-1/2 x 5/8 (125 x 38 x 16)Wheels rear, in. (mm) 8 x 1-1/2 x 5/8 (203 x 38 x 16)Handlebar adjustment YesBlade guard type BoltedNumber of belts 12 rib Poly V-beltBlade depth control Screw feedMaximum weight uncrated, lbs. (kg) 219 (99)Maximum weight crated, lbs. (kg) 276 (125)Dimensions uncrated, in. (mm) LxWxH 42 x 20 x 30 (1,067 x 508 x 991)

Power source......................................................GasolineEngine ....................................................................HondaSpecifications ........................................................GX390Net horsepower (rated by engine mfg.) .......................11Displacement - cu. in. (l) .................................23.7 (389)Bore/stroke - in. (mm).........................3.5 (88) / 2.5 (64)Cylinders/stroke ..........................................................1/4Fuel capacity - gal. (l) .........................................1.6 (6.1)Oil Capacity - qt. (l) ............................................2.3 (1.1)Air filter...........................Dry type dual element, cyclonicStarter.....................................................................RecoilEngine cooling .............................................................Air

Central lift bail foreasy loading andunloading.

3

1067

-21-

10

CONCRETE SAWACCESSORIES

FS 4800 D

Husqvarna FS 6600 D 3-Speed, FS 6600 D,FS 4800 3-Speed, FS 4800 D Accessories

70

FS 3500

DESCRIPTION ITEM NO.Water pump kit (electric) 183416Deluxe spotlight kit (dual lens) 167656Tie down kit 167568Outer flange kit (15/16" joint sawing) 176292Blade wrench 043650Parking brake kit 183995Extra slip-on blade guards18" blade guard slip-on 54219877826" blade guard slip-on 54220326630" blade guard slip-on 54220330514" narrow blade guard 16749226" narrow blade guard 167498

FS 500

Husqvarna FS 500 Series Accessories

DESCRIPTION ITEM NO.Bladeshaft wrench 542202292Water tank kit (6.6 gal.) 541208286Extra blade guards18" blade guard 54220236020" blade guard 54220408924" blade guard 542204187

Husqvarna FS 413 Accessories

DESCRIPTION ITEM NO.Bladeshaft wrench 542202292Water tank kit (6.6 gal.) 541208286Extra blade guard18" blade guard 542202360

FS 413


DESCRIPTION ITEM NO.Bladeshaft wrench 543045904Water tank kit (7.9 gal.) 543049899Front cutting guide 504069201Extra blade guard18" blade guard (1-piece only) 502082901

FS 400


DESCRIPTION ITEM NO.Bladeshaft wrench 543045904Water tank kit complete 543084137Extra blade guard14" blade guard 505424601

FS 309

Husqvarna MG 8, MG 10 Accessories

DESCRIPTION ITEM NO.Replacement blade wrench - 1" open end 172378Replacement blade wrench - 9/16" hex 170562

MG 8

DESCRIPTION ITEM NO.Weight kit, 1 bar - 35 lbs. (FS 6600 D) 542196171Weight kit, 2 bar - 70 lbs. (FS 6600 D) 542196172Dual work light kit 181117Water pump kit (FS 6600 D) 542199626Water pump kit (FS 4800 D) 542206672Extra blade guards14" blade guard slip-on 54120836618" blade guard slip-on 54220327920" blade guard slip-on 50485770126" blade guard slip-on 54220326630" blade guard slip-on 54220330536" blade guard slip-on 54220331842" blade guard bolt-on (FS 6600 D) 54219963142" blade guard slip-on (FS 6600 D) 50401940142" blade guard slip-on with mount kit 504558301Bladeshaft plunge kit 20" (FS 6600 D) 516026601Catalytic converter kit (FS 4800 D)* 504611202*Not intended for indoor use.

FS 6600 D

Husqvarna FS 3500 E Accessories

639-

37-1

0

SAW BLADES

High-Speed Segmented Diamond Blades• Application All-purpose. • For Equipment Type High Speed, • Cutting Type Wet or Dry Cutting. Small Walk-behind, and Masonry saws. HI5® (Super Premium) is for fast cutting of a wide variety of materials on the first pass, such as curedconcrete and brick. The HI5 is the only all-purpose diamond blade with aggressive notched segmentswhich grab and grind material for a rapid “first cut.” Total Segment Height: .475" (.375" diamond depth; .100" segment base) EH5 for general purpose cutting of concrete, masonry and stone. EH8 for use on a wide range of abrasive materials such as soft brick, abrasive block and green concrete or cured concrete with soft aggregate. Extreme EH10 slightly harder bond for longer life when cutting a wide range ofabrasive materials such as soft brick, abrasive block and green concrete.

Grinding Cup Wheels - General Purpose Wheels Red C16ST silicon carbide specification wheel is used for general purpose work; concrete and masonry products, cast iron, ductile iron and titanium.Blue A16ST aluminum oxide specification wheel is for general purpose work on mild steels, stainless steel, alloys and cast steels.

Resinoid cup grinding wheels for fast, efficient grinding and long life; all Husqvarna grinding cup wheels include steel backs for increased safety.Size Inches (mm) Red Blue

C16St A16St4 (102) x 2 x 5/8 - 11 22984 40S0015 (127) x 2 x 5/8 - 11 40S006 40S0046 (152) x 2 x 5/8 - 11 40S10 40S007

MILLENIUM® F770A/F780A/F785A.ASPHALT BLADES, 30 - 120 HPF770A blade is used to cut non-abrasive aggregate or rounded non-abrasive sand.F780A blade is for general purpose asphalt cutting.F875A blade cuts asphalt with soft aggregates or very abrasive sand.• 14" - 18" narrow notch diameter blades have vertical insert

`undercut protection.• Blades 20" in diameter or larger have recessed segment undercut protec-

tion.• All wide notched blades have both vertical insert and recessed segment

undercut protection.• Total segment height is .390" (.315" diamond depth; .075" segment base).

* Brazed items.

Size Inches (mm) H15 EH5 EH8 EH10

12 (305) x .125 x 1DP - 20mm B 542774540 542775594 542775596 542775599

14 (356) x .125 x 1DP - 20mm B 542774541 542778735 542775597 542775600

16 (400) x .140 x 1DP - 20mm B 542774542 542775595 542775598 542775601

Size - in. (mm)Narrow notch

F710C (C1-315)

F720C (C2-315)

F730C (C3-315)

F740C (C4-315)

20 (508) x .125 x 1 DP 542758616 542758662 542758754 542758800 20 (508) x .140 x 1 DP 542758617 542758663 542758755 542758801 20 (508) x .165 x 1 DP 542758619 542758665 542758757 542758803 24 (600) x .165 x 1 DP 542758623 542758669 542758761 542758807 24 (600) x .187 x 1 DP 542758624 542758670 542758762 542758808 24 (600) x .220 x 1 DP 542758625 542758671 542758763 542758809 26 (660) x .165 x 1 DP 542758627 542758673 542758765 542758811 26 (660) x .187 x 1 DP 542758628 542758674 542758766 542758812 26 (660) x .220 x 1 DP 542758629 542758675 542758767 542758813 Wide notch26 (660) x .165 x 1 DP 542758637 542758683 542758775 542758821 26 (660) x .187 x 1 DP 542758638 542758684 542758776 542758822

MILLENIUM® F710C/F720C/F730C/F740C.315" Series Cured Concrete Blades, 35-120 HPF710C blade is used to cut flint aggregate, river gravel and concrete with heavy steel reinforcement.F720C blade can cut concrete with a medium steel reinforcement and river gravel.F730C blade is perfect for cutting hard limestone to granite as well as concrete with light steel reinforcement.F740C blade cuts limestone, abrasive sand aggregate and some asphalt overlay.• 48" deep set recommendation: 18 x .250", 26 x .220", 36 x .220", 48 x .220".• All narrow notch blades 24" in diameter or larger have recessed segment

undercut protection.• Total segment height is .390" (.315" diamond depth; .075" segment base).

Size - In. (mm) Narrow notch F770A* (A1) F780A (A2) F785A* (A3)20 (508) x .140 x 1 DP 542759328 542759362 542759396 20 (508) x .165 x 1 DP 542759569 542759570 542759571 24 (600) x .165 x 1 DP 542759329 542759363 542759397 24 (600) x .187 x 1 DP 542759330 542759364 542759398 26 (660) x .165 x 1 DP 542759331 542759365 542759399 26 (660) x .187 x 1 DP 542759332 542759366 542759400 Wide notch26 (660) x .165 x 1 DP 542759346 542759380 542759414 26 (660) x .187 x 1 DP 542759347 542759381 542759415

71

3

639-

44-1

0

72

BLADES

HARD CONCRETE, GENERAL PURPOSE, GREEN CONCRETE, ASPHALT BLADES, 5-65HP

Gold 150B blade can cut hard to critically hard aggregate with light to medium steel reinforcing.

Blue 200B blade is a general purpose blade used to cut soft to medium-hard aggregate with light steel reinforcing.

Blue 300B blades cuts soft to medium-soft aggregate and can also be used for cured joint widening.

Red 450B-R blade is used for cutting green concrete, asphalt over concrete or asphalt with hard aggregate. Undercut protection is standard on this blade.

Black 500B-R blade has extra extra long life when cutting abrasive asphalt. Undercut protection is standard on this blade.

Job Size: Medium to largeHorsepower Range: 5-65 HP concrete sawsFeature: Higher production, low cost per footTotal Segment Height: .390" (.315" diamon depth;

.075" segment base)

Banner Line®

Narrow notch Gold 150B Blue 200B Blue 300B Red 450B-R Black 500B-R

18 (450) x .125 x 1 DP 773245 773248 773251 773255 773259

20 (508) x .125 x 1 DP 581730 773289 773252 773256 773260

24 (600) x .155 x 1 DP 773292 773264 581819 773273 773278

24 (600) x .175 x 1 DP 773261 773265 773269 773274 773279

Wide Notch

26 (660) x .155 x 1 DP 773262 773266 773270 773275 773280

30 (762) x .175 x 1 DP 773263 773267 773271 773276 773281

36 (914) x .175 x 1 DP - 773268 773272 773277 773282

FAST REMOVALGW1 is for fast removal (single rim) on concrete, masonry, stone and similar materials.SMOOTH FINISHGW2 is for long life and smooth finish (double rim) on concrete, masonry, stone and similar materials.GWTurbo is for a faster and smoother finish (segmented turbo) on concrete, masonry, stone and similar materials.

Total Segment Height: .200" diamond segment

FAST REMOVALLW1 is for fast removal (single rim) on concrete, masonry, stone and similar materials.SMOOTH FINISHLW2 is for long life and smooth finish (double rim) on concrete, masonry, stone and similar materials.LWTurbo is for a faster and smoother finish (segmented turbo) on concrete, masonry, stone and similar materials.

Total Segment Height: .200" diamond segment

Size Inches4 (102) x 5/8 - 11 THD4 (102) x 5/8 - 11 THD4 (102) x 5/8 - 11 THD7 (178) x 5/8 - 11 THD7 (178) x 5/8 - 11 THD7 (178) x 5/8 - 11 THD

639-

42-1

0

GRINDING DISCS

GW Dri Disc®

LW Dri Disc®

Size Inches4 (102) x 5/8 - 11 THD4 (102) x 5/8 - 11 THD4 (102) x 5/8 - 11 THD4 (102) x 7/8 - 5/8 B4 (102) x 7/8 - 5/8 B4 (102) x 7/8 - 5/8 B5 (127) x 5/8 - 11 THD5 (127) x 5/8 - 11 THD5 (127) x 5/8 - 11 THD

5 (127) x 7/8 - 5/8 B5 (127) x 7/8 - 5/8 B7 (178) x 5/8 - 11 THD7 (178) x 5/8 - 11 THD7 (178) x 5/8 - 11 THD7 (178) x 7/8 - 5/8 B7 (178) x 7/8 - 5/8 B7 (178) x 7/8 - 5/8 B

3

73

2434

-16-

10

CUT-OFF SAWS

Professional User

There are no easy jobs in the construction and demolition business, butwhen it comes to cutting performance there is one easy choice: the 14"TS 420 STIHL Cutquik® cut-off machine.

Introducing the TS 420 STIHL Cutquik® cut-off machine, one of the bestwe’ve ever built.

We’ve followed up the legendary and number one worldwide-selling TS 400 with a cut-off machine that is even better. This new TS machinecan help you work longer, and keep on schedule, thanks to patentedadvancements in technology and renowned STIHL innovation.

With the TS 420 STIHL Cutquik® cut-off machine, you can work longerand more comfortably, and get the job done right. The fact is that noother cut-off machine delivers this unique blend of performance, comfort and efficiency.

Standard Features • X2 low maintenance air filtration system.• Filters can last up to 1 year.• No need to clean filters.• Newly designed anti-vibration system reduces vibration up

to 43% over previous models.• Powerful and fuel-efficient stratified charge engine.• Emissions reduced up to 44% compared to TS 400.• IntelliCarb™ compensating carburetor.• Lightweight and well balanced compact top handle design.• ElastoStart™ starter handle and decompression valve.• Semi-automatic belt tensioner.• Reversible cutting arm for inboard or outboard cutting.• Able to be mounted on cart with adapter kit.• Integrated water attachment.

IMPORTANT INFORMATION: Improper use of any power tool may cause serious or fatal injury. Read, understand and follow carefully the operating and safety instructions in yourowner’s manual before using these products.

WARNING! Never use carbide-tipped, wood cutting or circular saw blades on cut-off machines. They can cause severe personal injury or death from reactive forces, blade contact orthrown tips. Never cut wood of any type.

74

TS 420 STIHL Cutquik®

• No need to waste time cleaning filters.• No messy, grimy and less efficient

oil-soaked foam filters to fool with.• Over twice the life of previous filtra-

tion systems. This filter can last up toone year, based on cutting conditions.

• Superior air filtration (99.96% clean-ing efficiency) leading to longerengine life.

• Manifold separation tunnels removeover 80% of dust before it ever reaches the filter.

• Standard in the TS 410, TS 420, TS 700 and TS 800.

• Easy access to the air filter X2 Air Filtration.

TS 410 TS 420 TS 460 TS 700 TS 800Displacement 66.7cc 66.7cc 72.4cc 98.5cc 98.5cc

(4.07 cu. in.) (4.07 cu. in.) (4.42 cu. in.) (6.0 cu. in.) (6.0 cu. in.)Engine Power 3.2kW 3.2kW 3.5kW 5.0kW 5.0kW

(4.4 bhp) (4.4 bhp) (4.75 bhp) (6.7 bhp) (6.7 bhp)Weight 9.4kg 9.6kg 10.65kg 11.6kg 13.2kg

(20.7 lbs.)* (21.2 lbs.)* (23.5 lbs.)* (25.6 lbs.)* (28.7 lbs.)*Fuel Capacity 770cc 770cc 960cc 1200cc 1200cc

(26 oz.) (26 oz.) (33.4 oz.) (40.6 oz.) (40.6 oz.)Engine Speed 9,500 rpm 9,500 rpm 9,500 rpm 9,800 rpm 9,000 rpm

(Elec. Gov.) (Elec. Gov.) (Elec. Gov.) (Elec. Gov.) (Elec. Gov.)Maximum Spindle Speed 5,350 rpm 5,350 rpm 5,350 rpm 5,350 rpm 4,600 rpmArbor Size 20mm 20mm 20mm 20mm 20mmMaximum Wheel Size 300mm 350mm 350mm 350mm 400mm

(12") (14") (14") (14") (16")Maximum Cutting Depth 100mm 125mm 125mm 125mm 143mm

(3.9") (4.9") (4.9") (4.9") (5.6")*Weight includes water attachment and guard.

Cut-off Machine Comparison Chart

2903

-1-1

0

ABRASIVE WHEELS

BONDED ABRASIVE BLADESFOR ALL HIGH SPEED GAS POWERED SAWS

High Speed Concrete Cut Off WheelsItem Number Dimensions Box Qty.

424-10612 12" x 1/8" x 1" 10424-11214 14" x 1/8" x 1" 10424-10212 12" x 1/8" x 20mm 10424-10814 14" x 1/8" x 20mm 10

High Speed Metal Cut Off WheelsItem Number Dimensions Box Qty.

424-15512 12" x 1/8" x 1" 10424-16114 14" x 1/8" x 1" 10424-15112 12" x 1/8" x 20mm 10424-15714 14" x 1/8" x 20mm 10

High Speed Ductile Iron Cut Off WheelsItem Number Dimensions Box Qty.

424-70512 12" x 1/8" x 1" 10424-11314 14" x 1/8" x 1" 10424-10312 12" x 1/8" x 20mm 10424-10914 14" x 1/8" x 20mm 10

Contractors demand superior performance and competitive prices on Cut-offWheels. That is why Virginia Abrasives bonded abrasives are the leadingchoice. Whether your customer is cutting metal, concrete or ductile iron, weoffer a product designed to keep them coming back. The fast delivery allowsyou to manage your inventory and provide excellent service. When it comesto bonded abrasives no one out-performs Virginia Abrasives.

Floor Grinding BlocksItem Number Dimensions Type

426-32402 2" x 2" x 4" 24-grit426-31202 2" x 2" x 4" 10-grit426-30802 2" x 2" x 4" 8-grit999-00007 Wooden Wedges

Flaring Cup Stones for ConcreteItem Number Dimensions

426-20205 5" x 2" x 5/8" - 11426-20406 6" x 2" x 5/8" - 11

75

3

1184

-6-1

0

76

ABRASIVE BLADES

Type 27 Depressed Center Grinding WheelsA 24 N - - - - Aluminum oxide general purpose wheel for grinding steel and other ferrous metals in normal working conditions.

High stock removal. Good wheel life.A 24 R - - - - Aluminum oxide general purpose wheel for heavier working conditions for steel and other ferrous metals. Good stock removal.

Longer wheel life.Small GrindersOrder # Size Spec. Application Max. RPM 655307000 4-1/2 x 1/4 x 5/8-11 A 24 R Steel 13,300Large Grinders616572000 9 x 1/4 x 7/8 A 24 N Steel 6,600

Type 1 “SLICER-PLUS” High - Performance Cutting WheelA 60 TX - - - - Coated aluminum oxide formulated to provide very long life and very aggressive cool cutting action on all metals.Small Grinders (Type 1)Order # Size Spec. Application Max. RPM 655998000 6 x 0.45 x 7/8 A 60 TX Stainless Steel 10,185

Type 1 “ORIGINAL SLICER” Cutting WheelA 60 TZ - - - - Aluminum oxide wheel for steel and other ferrous metals. Extremely fast rate of cut. Good wheel life.Small Grinders (Type 1)Order # Size Spec. Application Max. RPM 655331000 4-1/2 x 0.40 x 7/8 A 60 TZ Steel / Stainless Steel 15,000

Type 1 Cutting Wheels - High Speed SawsA 24 N - - - - Aluminum oxide general purpose wheels for cutting steel and other ferrous metals. Good wheel life.C 24 N - - - - Silicon carbide general purpose wheel for stone, concrete, cast iron, ductile iron,masonry materials, non-ferrous metals, brass,

bronze, plastic, etc. Fast rate of cut. Good wheel life.

Order # Size Spec. Application Max. RPM 616140000 14 x 1/8 x 20mm A 24 N Steel 5,460616160000 14 x 1/8 x 20mm C 24 N Masonry / Non-Ferrous 5,460

Type 11 Cup Wheel with Steel Back - Large GrindersA 16 Q - - - - Aluminum oxide general purpose wheel for grinding steel and other ferrous metals. High stock removal. Good wheel life.

Order # Size Spec. Application Max. RPM 616343119 5 x 4 x 2 x 5/8-11 A 16 Q Steel / Ferrous Metals 7,200

Type 27 Zirconia Alumina Flap DiscSpec. - - - - Zirconia alumina grain delivers extremely long life with very aggressive stock removal and excellent blending capabilities.

Use for steel, stainless steels, and non ferrous metals.Standard - - - - Long life with aggressive stock removal and good blending properties.

Order # Size / Spec.624248000 4-1/2 x 7/8 - ZA80

Flap Wheel - Mounted Style - 1/4 ShankStandard - - - - Aluminum oxide on resin fiber backing provides excellent stock removal on contoured steel shapes

and in confined areas.Order # Size Spec. Application Max. RPM 655374000 2 x 1 A 60 Steel / Stainless Steel 25,000

Wire Cup BrushSmall Air and Electric GrindersOrder # Dia. Thread Wire Max RPM Use on623796000 2-3/4" M14-2.0 0.014 carbon stl knotted 12,000 4"-6" grinders

Wire Wheel BrushSmall Air and Electric GrindersOrder # Dia. x Face Thread Wire Max RPM Use on656303000 4" x 3/16" M14-2.0 0.020 carbon stl knotted 20,000 4"-6" grinders

0º to 15º

Other sizes available.









Applications:• Handheld core drilling up to 4" in diameter.• Can be mounted on Husqvarna drill stand DS 150 for angle

drilling and holes up to 6".• For reinforced concrete, bricks and other building material.• Drills holes for ventilation, plumbing pipes, joints, electrical

sockets and telecom cables.

Benefits:• Equipped with Elgard™, which indicates via pulsation when

the machine is overloaded, provides a longer product life.• For a smooth start to drilling, the drill motor is equipped

with Softstart™.• For drilling in hard materials such as rebar, the drill motor is

equipped with Smartstart™.• The three-speed water-cooled gearbox provides optimal drilling

performance and longer service intervals.• Designed with a plastic housing which makes it more durable

against drops and daily wear.• The handle and the controls are designed and positioned to further

enhance ergonomics and user comfort.• The position of the pistol grip handle and the front handle provides

the operator good control of the drill bit torque.

1067

-22-

10

CORE DRILLING

Applications:• Drill holes up to 16" (extra spacer required).• 1" to 14" bit capacity standard. Spacers available for larger bit sizes.• 42" long, precision ground and plated 2-7/8" square column reduces flex

for more accurate drilling.

Benefits:• Reinforced base for added rigidity.• Optional control panel includes on/off switch, ammeter and two receptacles

for the motor and vacuum pump.• Jack screw is standard and provides stability for ceiling bracing.• Precision rack and pinion gear system for smoother operation.• Adjustable and replaceable brass shims inside carriage provide less flex,

promote precise head alignment and smooth feed travel.• Roller carriage option.

DS 800Core Drill Rig

77

DS 800 TECHNICAL SPECIFICATIONS DS 800/DM 280 HIGH SPEED DS 800/DM 280 E LOW SPEEDCombo base item no. 965177201 965177204Combo base w/ vac. assy. item no. 965177202 965177205Anchor base item no. 965177203 965177206Combo base, roller carriage item no. 965177213 965177216Combo base, roller carriage, vacuum assembly item no. 965177214 965177217Anchor base, roller carriage item no. 965177215 965177218

STANDS LESS MOTORS ITEM NO.DS 800 combo base stand less control panel 965176901DS 800 anchor base stand less control panel 965176902DS 800 combo base stand with control panel 965176903DS 800 anchor base stand with control panel 965176904DS 800 stand with roller carriage less control panel, combo base 965176905DS 800 stand with roller carriage less control panel, anchor base 965176906

DM 230Handheld Core Drill Motor

TECHNICAL SPECIFICATIONS DM 230 3-SpeedItem no. 968411301Power, watts / Voltage, volts 1,850 / 110Motor 1-phase, electricRated output, watts 1,100Rated current, amps 15Spindle speed idle high speed, rpm 900 / 2,150 / 4,500Spindle speed full load high speed, rpm 500 / 1,400 / 2,900Maximum bit diameter with stand/handheld, in. (mm) 6 (152)Mounting collar, in. (mm) 238 (60)Spindle thread, outer (inner) 1¼"-7 (5/8"-11)UNC water coupling G ¼"Sound pressure level, dB(A) 90Sound power level, dB(A) 94Weight, lbs. (kg) 12 (5.4)

TECHNICAL SPECIFICATIONSPower, watts 2,300Voltage/amperage 110/20Maximum bit diameter without spacer, in. (mm) 14 (350)Travel Length, in. (mm) 25-1/2 (648)Spindle speed full load high speed, rpm 350 / 780 / 1,340Spindle speed full load low speed, rpm 240 / 540 / 930Weight, lbs. (kg) 108 (49)

3

639-

43-1

0

DIAMOND CORE BITS

78

GENERAL PURPOSE, CONCRETE AND MASONRYBanner Line® bits are used for general purpose drilling of concrete, masonry and brick. This includes concrete with soft to hard aggregate and light to medium steel reinforcing and is also effective ongranite, marble and stone.Custom specs are available including open-end, spoke-back, non-standard length and threaded tubing for deep drilling. Our 3/8" to 1-1/2" bits have a 5/8" adapter. Bits 1-5/8" and above have a 1-1/4" - 7" thread adapter.

Total Segment Height: .300" (.200" diamond depth; .100" segment base)

Bit Diameter 3/8" - 14"

Bit Diameter Adapter Thread3/8" - 1-1/2" 5/8"1/2" - 5/8" 1/2" - 20"3/4" - 1-1/2" 5/8" - 11"1-5/8" + 1-1/4" - 7"

GENERAL PURPOSE, MASONRYDRI5 is designed for drilling brick when using an angle grinder. Also can be used for fast drilling of block, brick or soft aggregate concrete on angle grinders or hand held drills. Not recommended for hard concrete or steel.DRI8 is designed for long life drilling in lightweight block or concrete block materials on hand drills or angle grinders. Can also be used for long life drilling of brick on hand drills. Not recommended for cured concrete or steel.The specially designed barrel vents keep bits cool and provides fast removal of cuttings. Use these bits on core drilling machines or right angle grinders (mount bits directly onto standard 5/8"-11grinder spindles). These bits drill faster than conventional carbide-tipped percussion bits for a smoother finish and little patching.

Feature: High production; low cost with exceptional life.Total Segment Height: .280" (.220" diamond depth; .060" segment base)

Dri Bit SpecificationsOverall Length 10-1/2"Core Travel 10"Thread Size 5/8" - 11

Banner Line® Bits

Dri Bit™

395-

18-1

0

CORE DRILLING / WIRE SAW

CORE DRILLING RIGM-1 Complete Combination Rig• 1" to 10" bit capacity (14" with a spacer block). • Dual switch/outlet control panel & amp meter. • Slide handle allows drilling in tight areas. • Streamlined base and carriage. • 2-1/2" square column with black oxidized finish. • Quick changeover from vacuum to anchor base. • 6" wheels for better mobility.

Complete Combination Rig Includes:Anchor/vacuum base, mast, carriage,control panel, vacuum pump, ceiling jack,motor mount plate and your choice ofdrill motor: Core Bore, Milwaukee or Weka

PORTABLE DIAMOND WIRE SAWS

WS50 WIRE SAW• Articulating wheel for vertical and horizontal cuts. • Locking casters. Adjustable slide carriage. • Gear box makes it easy to change from vertical to

horizontal cutting. SPECIFICATIONSDimensions: 52" H x 32" W x 108" L Weight: 1,500 lbs. Drive Wheel: 36" dia. Tension Control Cylinder: 36" stroke Recommended Power Supply: 25 GPM @ 2500 PSI Wire Speed: 0-5,000 ft./min. infinitely variable, reversible Sawing Angle: Set up vertical or horizontal from same frame Options: Mount stand, Universal wire saw clamp, 10" wheel

HYDROSTRESS WIRE SAWThe Universal Wire Saw with Integrated Wire Storage

SB Wire Saw • Patented multiple roll

drive that makes it possible to start run-ning with minimum wire tension and complex cutting geometry.

• Cutting rate is 50% higher than conventional systems.

• Emission-free demolition. • Integrated water distribution valve. SPECIFICATIONS Wire storage capacity: Capable of cutting 33 ft.Wire required: Minimum 50 ft.Max. Wire Length: No limitMotor: 26CC/1.83 CIR for 12-18 gpm power packswithout case drain.Feed: Hydraulic motor, requires separate line.Dimensions: 25" L x 51" H x 26" WWeight: 375 lbs.

SK-B Wire Saw • Direct mounting together with a

patented multiple roll drive that guarantees easy installation and trouble-free start-up.

• Converts from drill rig to wire saw in minutes.

• Large storage capacity that cuts perimeters up to 19-1/2 ft.

SPECIFICATIONS Wire storage capacity: Capable of cutting 20 ft.Wire required: Minimum 25 ft.Max. Wire Length: No limitMotor: 26CC/1.83 CIR for 12-18 gpm power packs.Feed: Hydraulic motor, requires separate line.

Mobile Track Wire Saw • Twice the cutting speed of conventional wire saws,

infinitely variable speed, reversible drive. • Works well on rough terrain, inclines and where

conventional wire saws can’t operate. • Eliminates most of wire sawing set-up time. • Powerful V6 4.3L GM industrial engine. • Rubber tracks for superior movement. • Entire saw can be pulled back; pulling the wire through the cut. • 36" drive wheel with reversible rotation and

infinitely variable speed. • 12" idler wheels with grease bearings and replaceable liners.• Innovative tensioning spring for consistent wire tension.• Radio Remote Control has a range of up to 300 ft.

for safety and convenience.

SPECIFICATIONS: Fuel tank: 22 gallon Filtration system: Dual stage air filter Weight: 3,300 lbs. Length: 78" without idler Height: 68" with muffler Width: 48"

3

79

2171

-8-0

6

HYDRAULIC CHAINSAWS

ICS® 880F4 The new 880F4 cutting system offers the superior strength ofFORCE4™ technology in a package that meets industry standards ofdesign and ergonomics. Built for the hardcore cutter, this sleek pow-erhouse is packed with features designed to make it the hardestworking saw ICS® has ever made. You get the unique versatility of agenuine ICS® concrete cutting chainsaw, including the ability to cutsmall mechanical openings, deep plunge cuts. Cut perfect cornersand an endless variety of irregular shapes that are simply not possi-ble with circular saws. Available in both 8 gpm and 12 gpm models.

ADVANTAGES:• Fast, efficient, versatile and easy to use.• Cuts mechanical openings quickly and perfectly.• Narrow, straight plunge cuts up to 25 inches deep.• Perfect square corners.• Reliable and easy to maintain.• Low cost of operation.

FEATURES:• Safety operating trigger prevents accidental starting.• Automatic water valve integrated with hydraulic trigger

provides water on demand.• Built-in WallWalker® provides leverage advantage to make

cutting easier.• Modular design for easy service.• Ergonomic rear handle allows multiple hand positions.• Tough industrial finish on die-cast aluminum body for long

lasting durability.

880F4 SPECIFICATIONS:

Operating Speeds• 6100 rpm (8gpm) / 6400 rpm (12gpm)

Torque• 122 in.-lbs. (8gpm) / 172 in.-lbs. (12gpm)

Horsepower• 11.5 hp (8gpm) / 17.5 hp (12gpm)

Hydraulic Supply• 8 gpm (30 liters/min.) / 12 gpm (45 liters/min.)• 2500 psi (172.5 bar)

Noise Level• 88dB at 3 feet (approx. 1m)

Vibration Level• 4 meters/second2 (front handle)

Water Supply• Minimum 20 psi (1.5 bar)

Weight• 27.3 lbs. (12.4kg) with 15-inch bar and chain

Available bar lengths• 10 inches (25cm)• 15 inches (38cm)• 20 inches (50cm)• 25 inches (63cm)

ICS® 814PROFor all those times when you don’t really need a full-size concretesaw, for those tight places where a larger saw won’t fit or can’t cut asmall enough opening, ICS has the answer. The 814PRO is arugged, reliable tool designed for the rigors of construction, yet it’ssmaller and lighter than our other hydraulic tools. The 814PRO sawis a wet-cutting system which uses water for eliminating airbornedust and for cleaning and lubricating the moving parts of the dia-mond chain. Using ICS diamond chains with SealPro®, water can besupplied from an ordinary garden hose. Ideal for utility work, likeplumbing or electrical openings, the 814PRO saw will cut openingsas small as 3.5 x 3.5 inches. No construction site should be withoutat least one.

ADVANTAGES:• Extremely lightweight, under 15 pounds. • All the benefits of diamond chain technology in a compact,

easy to use size.- Perfect corners, without overcutting. - Plunge cuts up to 12-inches deep. - Very small openings (3.5 inches x 3.5 inches).

• Inexpensive.• Costs less than full size hydraulic saws. • Reliable and low maintenance. • Hydraulic system and integrated design extremely rugged

and easy to service. • Exclusive ICS® Stretch Reduction System (S.R.S.) maximizes

chain life, and reduces need for adjustments. • Quick and easy clean-up when used with TSS system.

814PRO SPECIFICATIONS:

Hydraulic Supply Flow (max):• 8 gpm (30 liters/min.) • Can be used with higher flow systems

ONLY with flow adapter (ICS part number 70350) Pressure (max):

• 2500 psi (172.5 bar)Valve:

• Open centerWater Supply

• Minimum 20 psi (1.5 bar)

Weight• 15 lbs. (6.8kg)

with 13-inch bar and chainAvailable Bar Lengths

• 13 inches (32cm)Chain Speed

• 4950 fpm (25m/s), free runningPigtails Dimensions

• 18 inch length • 18 inches (46cm) Length• 1/2 inch diameter • 10 inches (25cm) Height• 2,500 psi working pressure • 8 inches (20cm) WidthSprocket Connectors• 7 tooth rim with e-clip • HTMA 1/2-inch Flush-Face

Noise Level Vibration Level• 88dBA@ 3 feet (approx. 1m) • 3.5 meters/second2 (front handle)

TSS Total Slurry Solutions• The 814PRO Hydraulic Saw comes equipped to accept the ICS® TSS attachment.

This allows you to capture the slurry with a Hi-Lift Performance Vacuum System also available from ICS.

80

P95 POWER PACKThe ICS Multiflow Powerpack is a dependable self-contained source of hydraulic power that is easily transportable to any jobsite. You can set the flow rate to either 5 gpm or 8 gpm to powerthe ICS® 880F4, 814PRO hydraulic chainsaw, or a wide variety ofother hydraulically powered equipment.

FEATURES:• Self-Contained. • Superior Cooling • Easily Transportable. (5 hp heat rejection).• Versatile. • Auto-idle capable.• Adjustable. • Ergonomic design for ease of use. • Keyless Electric Starting. • Engine over-speed shut-down. • Large pneumatic tires. • Low oil shut-down. • Lifting handles and eyes. • Easier hydraulic tank removal.• Larger fuel capacity. • Easier fuel tank removal. • Tool circuit lock-out • Load compensating hydraulic flow.

during start-up.

SPECIFICATIONS:Multiflow Hydraulics

• 8 gpm (30 liters/min.) at 2,500 psi (172 bar)• 5 gpm (20 liters/min.) at 2,500 psi (172 bar)

Engine• 18 horsepower V-Twin, air cooled • Briggs & Stratton Model 350447008401• Gasoline, 85 Octane • Fuel Capacity: 7 gal. (27 liters)

Hydraulic System• Reservoir: 3 gal. (11 liters) • Relief valve setting: 2,100-2,300 psi (145 - 158 bar)• Full relief setting: 2,500 psi (172 bar) • Hydraulic oil: SAE 10WT

Dimensions• Length: 36 inches (91cm) • Width: 23 inches (58cm)• Height: 29.5 inches (75cm)

Weight • 330 lbs. (150kg)

Soft Abrasive/ Natural Stone Medium Concrete/ Hard Concrete/Brick Light Reinforcement Heavy Reinforcement

2171

-10-

10

POWER PACK / CHAINSAW ACCESSORIES

DIAMOND CHAINS AND GUIDEBARSAll ICS® diamond chains come with patented o-ring technologyinserted within each connecting link to minimize water and improve lifetime.

MAX SERIES DIAMOND CHAINS

Best value for the everyday user.

Patented bumper design for smooth cutting performance. MAXseries diamond chains are designed to be the best general purposechains for ICS® brand gas concrete saws.

PRO SERIES DIAMOND CHAINS

Maximum performance for the professional concrete cutter.

Engineered for the highest possible performance, these are thechains the PRO Cutters prefer.

GUIDEBARSGenuine ICS® guidebars, replacement parts and other accessorieskeep you cutting at peak efficiency.

DIAMOND CHAIN SELECTION CHART

PR

OF

OR

CE

4M

AX

SE

RIE

SS

ER

IES

SE

RIE

S

P95

TwinMAX™ � � �

TwinMAX™ Plus � � �

TwinMAX™ Abrasive �

ProFORCE™ � � �

ProFORCE™ L � � �

ProFORCE™ S � � �

ProFORCE™ Abrasive �

ProFORCE™ Corner* � � � �

TwinPRO™ � �

SoftPRO™ � �

PremiumPRO™ � � �

*For use by professional concrete cutters for chasing corners only.

3

81

360-

8-10

HYDRAULIC POWER UNITS /PUMPS / SAWS / BREAKERS

82

The HydraPakHydraPaks are powerful, portable hydraulic power units that operate more efficiently and with less noise than other types of power systems. HydraPaks are easily transported to the jobsite inthe back of a pickup truck or van. Compact, lightweight hydraulic power source for RGC Hydraulic tools. Easy maintenance and parts replacement. Detachable handles for easy transporting and storage.Lifting hook and 6-gallon oil reservoir. Controls easily accessible for safety and comfort. Cart mounted with large 16" pneumatic tires for easy transporting.

GAS HYDRAPAK FEATURES • Electric start and low oil shutdown on all models. • Powder-coated tubular steel frame protects unit from damage.• Heavy-duty 8-tube heat exchanger on most models.• HV1855, HV1858 and HV1810 are equipped with an 18 hp B & S

Vanguard gas engine with Performance Control™ electronic governor.

ELECTRIC HYDRAPAK FEATURES• Controls and handles located at

convenient height.• 10 hp, 60 hz

Baldor electric motor. Model HE 1058 and HE1010

Hydraulic BreakerOUTSTANDING FEATURES• Higher performance-to-weight ratio than other hydraulic and

pneumatic breakers. • Lighter weight and more portable than pneumatic systems.• New ergonomic handles are standard on HB37E, HB47E, HB70E and

HB89E to reduce operator fatigue and increase productivity.• Alternative noses available to accept different size tools.• Powered by the RGC® HydraPak or other compatible power source. • Superior distributor system in the HB47E, HB70E and HB89E

further improves efficiency and dependability.• Absence of noise and dust producing exhaust delivers cleaner,

quieter and more efficient operation. • Continuous component lubrication

reduces wear, minimizes maintenance and extends product life.

• Hose whips and moil points included.

HB70E HydraBreaker Weight Class: 70 lb.Weight: 69.4 lbs. (31.5 kg)Length: 29" (738 mm)Steel Size Standard: 1-1/4" x 6" (32 x 152 mm)Steel Size Optional: 1-1/4" x 6-1/4" (32 x 160 mm) Impact per Minute: 1270Impact Force: 81 ft.-lbs. (110 J)Maximum Flow: 5 gpm (20 lpm)*Pressure: 2000 psi (138 bar)Max. Back Pressure: 215 psi (15 bar) *Consult factory for optional 8 gpm flow.

Hydraulic Saw

FEATURES • 14", 16", 20" and 24" models available. • Cuts concrete, stone, brick, block, pipe, reinforced concrete, steel

beams and other aggregates quickly and cleanly. • Cutting depths of 5-1/4" to 9-1/2". • Lightweight, rugged steel tube construction is lighter than gas saws. • Heavy-duty protective guard meets ANSI standards. • Dual function trigger for automatic wet cutting. • Accepts Abrasive or Diamond blades.• HydraCart and SawCart models available.• Trigger lockout for operator protection.• Use inside or outside - No exhaust pollutants. • Heavy-duty hydraulic motor for constant cutting speed under load.• Can be used underwater.

Model S14Blade Size: 14 in. (35.5 cm)Cutting Depth: 5-1/4 in. (13.3 cm)Blade Speed (max.): 4100 rpmFlow: 5-8 gpm (20-30 lpm)Oil Pressure Range: 2000-2500 psi (138-172 bar)Weight: 28 lbs. (12.7 kg)

HydraPumps• Small overall size allows for use in very tight spaces.• Small hole strainer available for the S3T model.• Built-in lifting eye/handle provides method to

carry, lift and lower.• Proven, durable design

for years of use.• Cast aluminum pump body.• Self-lubricating design.• Totally submersible.• Self-priming.• Designed to consistently

pump large volumes of liquids, these compact units are ideal for pumpingout vaults, trenches, ditches, ponds, tanks,pools, etc.

Model: S2TCAL-2 S3TPump Capacity: 125 gpm (473 lpm) 390 gpm (1476 lpm)Pressure Max: 2500 psi (170 bar) 2500 psi (170 bar)Flow: 5 gpm (19 lpm) 8 gpm (30 lpm)Operation: Open Center Open CenterMax. Lift: 210 ft. (64 m) 75 ft. (22.9 m)Discharge Size: 2 in. NPT (female) 3 in. NPT (female)

5.8 cm Outlet 7.6 cm OutletPump Diameter: 9-3/8 in. (24 cm) 11-3/4 in. (30 cm)Max. Back Pressure: 200 psi (14 bar) 100 psi (7 bar)Semi-solids (Max.): 1 in. (2.5 cm) 2-1/2 in. (6.4 cm)Couplings: 1/2 in. HTMA Flush-Face 1/2 in. HTMA Flush-FaceWeight: 17 lbs. (7.7 kg) 34 lbs. (15.4 kg)

3092

-1-1

0

83

HYDRAULIC BREAKERS

FEATURES and BENEFITS:

Oil Regeneration SystemThe effective oil regeneration system on theBXR Series traps hydraulic oil used in thedownward stroke of the piston and uses thisoil to assist in lifting the piston for the nextblow. This design boosts blow speed withoutthe need for additional flow, resulting in higher production rates.

Manual High Speed SelectionBX8 to BX30 breakers are equipped with amanual high or low speed select located onthe breaker. Switching to high speed allowsfor improved production rates in softer mate-rial such as concrete. The BX40 is equippedwith a hydraulic pilot operated two speedcontrol which is operated from the parentcarrier by the operator.

Long / Short Stroke SelectionOperator controlled long or short strokeselection on the BXR Series maximizes production rates by selecting between highimpact (long stroke)and high frequency (short stroke) modes via hydraulic pilotedstroke control.

Consistent Blow EnergyThe high volume nitrogen chamber and extra long stroke piston design reduces pressure fluctuations in the hydraulic circuitproviding consistent blow energy and recoilenergy absorption.

Anti-Blank FireAn anti-blank fire interlock prevents the blank fire of the tool, thereby reducing shockloading to the retaining pins and front head.

Remote GreasingA remote located greasing port situated nearthe top of the breaker close to the mainhydraulic circuit provides a convenient inter-face to carrier-mounted remote greasing systems, the use of which contributes to breaker longevity.

Exceptional Silence and Structural IntegrityThe boxed section housing provides excellent strength, while remaining light-weight. The suspended boxed housingdesign reduces vibration to the carrier without metal-to-metal contact.

Narrow Front HeadThe narrow box-housing design is well suited to tight trenching conditions. The narrow profile allows optimum visibility and access when working in tight quarters.

BX & BXRBX & BXR SERIES

Hydraulic BreakerHydraulic Breakerss

BX4 BX6 BX8 BX10 BX15 BX20 BX30 BX40

Energy Class ft.-lbs. (Joules) 400 (542) 600 (814) 800 (1,085) 1,000 (1,356) 1,500 (2,034) 2,000 (2,712) 3,000 (4,068) 4,000 (5,423)

Operating Weight(including top bracket) lbs. (kg)

419 (190) 439 (199) 734 (333) 950 (431) 1,354 (614) 2,048 (929) 2,665 (1,209) 3,832 (1,738)

Overall Length (including top bracket) in. (mm)

53 (1,352) 54 (1,380) 63 (1,603) 71 (1,805) 78 (1,981) 88 (2,225) 97 (2,455) 109 (2,764)

Oil Flow Range gpm (lpm) 7-11 (25-40) 8-13 (30-50) 8-15 (30-55) 12-21 (45-80) 13-26 (50-100) 24-29 (90-110) 26-37 (100-140) 29-42 (110-160)

Working Pressure Range psi (bar) 1,280-1,707 (90-120)

1,280-1,707 (90-120)

1,422-1,991 (100-140)

1,422-1,991 (100-140)

1,422-1,991 (100-140)

1,707-2,276 (120-160)

1,707-2,418 (120-170)

1,849-2,418(130-170)

Blow Rate bpmHigh Speed bpm

550-950 n/a

400-1,000 n/a

350-900 450-1,000

350-900 450-1,000

300-700 550-950

350-550 500-750

350-550 500-850

350-500450-600

Tool Diameter in. (mm) 2.1 (53) 2.4 (62) 2.8 (70) 3.1 (78) 3.3 (85) 4.1 (105) 4.7 (120) 5.3 (135)

Recommended Carrier Weight ton (kg)

1.2-4 (2,650-8,800)

3-4.5 (6,600-9,900)

3-86,600-17,600)

5-8 (11,000-17,600)

6-9 (13,200-19,800)

10-15 (22,000-33,100)

16-20 (35,300-44,100)

18-25(39,700-55,100)

BXR50 BXR65 BXR85 BXR100 BXR120 BXR160

Energy Class ft.-lbs. (Joules) 5,000 (6,800) 6,500 (8,813) 8,500 (11,524) 10,000 (13,558) 12,000 (16,290) 16,000 (21,693)

Operating Weight(including top bracket) lbs. (kg)

4,200 (1,905) 4,860 (2,204) 6,500 (2,948) 7,800 (3,538) 9,050 (4,105) 12,400 (5,625)

Overall Length (including top bracket) in. (mm)

107 (2,704) 114 (2,903) 133 (3,368) 137 (3,481) 143 (3,618) 160 (4,059)

Oil Flow Range gpm (lpm) 38-54 (144-204) 42-60 (159-227) 53-75 (201-284) 63-90 (239-341) 74-105 (280-398) 85-120 (322-454)

Working Pressure Range psi (bar) 2,150-2,700 (150-190) 2,150-2,700 (150-190) 2,150-2,700 (150-190) 2,150-2,700 (150-190) 2,150-2,700 (150-190) 2,150-2,700 (150-190)

Blow Rate Long Stroke*Short Stroke*

374-531514-730

341-488454-649

334-473444-629

294-417368-521

294-480368-600

231-374298-484

Tool Diameter in. (mm) 5.5 (140) 5.9 (150) 6.3 (160) 6.7 (170) 7.1 (180) 7.9 (200)Recommended Carrier Weight ton (kg)

17-30(37,500-66,100)

19-40 (41,900-88,200)

28-50(61,730-110,225)

34-68(74,950-149,900)

42-81 (92,600-178,600)

55-100(121,300-220,500)

*Speeds can increase up to 20% with the oil regeneration system.

3

3093

-1-1

0

84

AIR COMPRESSORS

M50 / M57 / M64

M100 / M122 / M200 / M270

Standard Features:• Heavy-duty diesel engines that comply with

Tier 3 emission standards.• Heavy-duty steel chassis.• Fully galvanized enclosure.• Tool boxes for convenient storage.• Modulation control.• Available skid-mounted.

M270• Lockable access doors

and instrument panel.• Liquid cooled turbo-

charged diesel engine

Compressor M50 M57 M65 M100 M122 M200 M270

Free air delivery 185 cfm 210 cfm 225 cfm 375 cfm 400 cfm 750 cfm 950 cfm

Working pressure 100 psig 100 psig 100 psig 100 psig 100 psig 100 psig 100 psig

Diesel Engine Kubota V1505-T IDI Kubota V2403 Kubota V2403T Kubota V3800 Deutz TCD2012L4 Caterpillar C6.6 Acert Mercedes Benz OM501LA

Power at full load 41 hp 47.2 hp 58.8 hp 90 hp 104.5 hp 186.4 hp 313 hp

Full load speed 3000 rpm 2600 rpm 2700 rpm 2600 rpm 2300 rpm 1950 rpm 1700 rpm

Off load running speed 2200 rpm 1800 rpm 2000 rpm 1800 rpm 1600 rpm 1200 rpm 1200 rpm

Fuel tank capacity 21 gal. 28 gal. 28 gal 40 gal. 50 gal. 70 gal. 146 gal.

Weight, dry 1555 lbs 2260 lbs. 2300 lbs. 3225 lbs. 4135 lbs 7055 lbs. 9634 lbs.

Weight, wet 1643 lbs. 2480 lbs.

Sound Level Max 76 db(A) at 23' 73 db(A) at 23' 70 db(A) at 23' 76 db(A) at 23' 76 db(A) at 23' 72 db(A) at 23' 70 db(A) at 23'

Outlets (2) 3/4" - (1) 1" (3) 3/4" - (1) 1-1/2" (3) 3/4" - (1) 1-1/2" (3) 3/4" - (1) 2"

Dimensions L x W x H* 130" x 55" x 49" 139" x 68" x 60" 144" x 68" x 56" 159" x 70" x 59-1/2" 185" x 74" x 63" 234" x 82" x 82" 232" x 81" x 104"

* Includes tow bar

Standard Features:• Heavy-duty Kobota turbo diesel engines

that comply with Tier 4 emission standards.• Large fuel tank for extended operation.• Convenient tool box for storage.• Galvanized enclosure.• Available skid-mounted.

M200• Lockable access

doors and instrument panel.

M122• Modulation control.

M100• Spacious, weatherproof tool box.

M57• Large tool box

holds two 90 lb. breakers

M50

M64• Large tool box

holds two 90 lb. breakers

Toku Rock DrillsDrilling through rock, concrete or brick, Tamco offers a rock drill that will fit your distinct requirements. • TS-55 60 pound class rock drill features rugged construction and designed for larger diameter bits and deeper drilling jobs. • TJ-20 and TJ-15 are mid-sized rock drills. Great for road building, shaft sinking, quarrying, as well as general demolition or

construction work. Include removable inline oilers. • THD-1100N is a lightweight D-handled drills that is able to get into smaller spaces other drills cannot.• All tools feature replaceable chuck bushings, drop forged alloy steel construction, and forged latch retainers.

Mufflers are available for the TS-55, TJ-20 and TJ-15 models. TJ-20 and TJ-15 models include Clear-View inline oilers.

TS-55

989-

3-10

85

BREAKERS / TAMPERS / CHIPPERS / DEMOLITION HAMMERS

Toku Paving Breakers• 30, 40, 60 and 90 pound classes. • Rugged four bolt backhead, drop forged alloy steel construction,

forged latch retainers, replaceable chuck bushings and safety triggers. Optional mufflers are available.

• 30 and 40 pound hammers are the perfect size and weight forlight to medium construction. They work great for demolishingblacktop, masonry walls, bridge decks, or digging in frozen soil.

• Toku 60 and 90 pound breakers are designed with the larger demolition jobs in mind.

Paving Breakers PB-90 PB-60 PB-40 PB-30Shank Size 1-1/8" x 6",

1-1/4" x 6"1-1/8" x 6", 1-1/4" x 6"

1" x 4-1/4" 7/8" x 3-1/4", 7/8" x 4-1/4"1" x 4-1/4"

Stroke Length 6" 4" 5-3/4" 3-11/32" Piston Diameter 2-5/8" 2-1/4" 1-3/4" 1-3/4" Impact Rate B.P.M. 1,250 1,400 900 1,550 Weight 92.4 lbs 66 lbs. 39.6 lbs. 33 lbs. Overall Length 28-1/2" 25-3/8" 26" 22-1/4" Air Consumption 77 C.F.M. 70 C.F.M. 56 C.F.M. 49 C.F.M.Air Inlet 3/4" NPT 3/4" NPT 1/2" NPT 3/8" NPTHose Size 3/4" 3/4" 3/4" 1/2"

Toku Tamper• Features heat treated alloy steel

cylinder, innovative features and rugged construction.

• Optional steel or rubber heads are available for the Toku tamper.

Tamper Jet-06 Bore 1-1/2" Stroke Length 5-1/2" Length 49" Weight 39.6 lbs. Air Inlet 1/2"Butt Diameter 6"Air Consumption 35.2 C.F.M.

Toku Chipping Hammers• The AA-0S is small on size but big on power.• The Toku THA series of gooseneck chipping hammers are available in 1" through 4" stroke lengths. Saw

tooth connection between the handle and cylinder provides a more secure, positive fit. Alloy steel drop forged handles, replaceable bushings, heat treated cylinders, reliable ring valve design and exhaust deflectors.

• Rugged TCH series of "D-Handle" chipping hammers are available in 2" through 4" stroke lengths. Featuresdrop forged handles, replaceable bushings, heat treated alloy cylinders, and exhaust deflectors. A rock solidfour bolt handle for maximum reliability and durability which allows a sure grip in all conditions. Optionalquick connect retainers are available for all TCH chipping hammers.

PB-30

TJ-15

Tamco, Inc.

Chipping Hammer AA-OS THA-1B THA-2B THA-3B THA-4B TCH-2 TCH-3 TCH-4Shank SizeStroke Length 1.8" 1" 2-3/32" 2-17/32" 4-1/32" 2" 2-1/2" 4"Piston Diameter 0.88" 1-1/8" 1-1/8" 1-1/8" 1-1/8" 1-1/8" 1-1/8" 1-1/8" Impact Rate B.P.M. 3,000-3,200 2,500 2,300 2,200 1,800 2,600-2,800 2,000-2,200 1,600-1,800Weight 7.9 lbs. 13 lbs. 13.6 lbs. 15 lbs. 16.1 lbs. 18 lbs. 19 lbs. 20 lbs.Overall Length 12.8" 15-9/32" 16-1/4" 17-23/32" 18-29/32" 14-3/4" 16" 17"Air Consumption 22.95 C.F.M. 28 C.F.M. 29.75 C.F.M. 31.8 C.F.M. 33.25 C.F.M. 29.75 C.F.M. 31.5 C.F.M. 33.25 C.F.M.

Air Inlet 3/8" NPT 3/8" NPT 3/8" NPT 3/8" NPT 3/8" NPT7/8" x 24Threads/Inch

7/8" x 24Threads/Inch

7/8" x 24Threads/Inch

Hose Size 1/4" 1/2" 1/2" 1/2" 1/2" 1/2" 1/2" 1/2"

.580" Hex or .680" Round Shank

AA-OS

TCH-3

THA-3B

PB-60

Repair parts available.

Rock Drill TS-55 TJ-20 TJ-15 THD-1100N Shank Size 7/8" x 3-1/4", 7/8" x 4-1/4"

1" x 4-1/4"7/8" x 3-1/4", 7/8" x 4-1/4"

7/8" x 3-1/4", 7/8" x 4-1/4"

7/8" x 3-1/4"

Stroke Length 2-9/16" 1-15/16" 1-3/4" 1-7/32" Piston Diameter 2-5/8" 2-11/16" 2-1/8" 1-1/2" x 7/8" Impact Rate B.P.M. 1,800 2,400 2,450 3,200 Rotation 200 R.P.M. 200 R.P.M. 250 R.P.M. 350 R.P.M.Weight 59.4 lbs. 40.7 lbs. 30.8 lbs. 11.4 lbs. Overall Length 22-3/8" 24-1/32" 18-1/2" 16-17/32" Air Consumption 91.81 C.F.M. 87.5 C.F.M. 56 C.F.M. 28. C.F.M.Air Inlet 3/4" NPT 3/4" NPT 3/4" NPT 3/8" NPTHose Size 3/4" 3/4" 3/4" 1/2"

3

1923

-13-

10

86

POWER TOOLS

SPECIFICATIONS H55SCK H60MRV H90SBShank Hex SDS Max -Amps 10.4 12.5 12.2Impact Rate 1450 bpm - 850 bpmImpacts/Min (Full Load) - 930 - 1,650 -Impact Energy 11.8 ft./lbs. 5.2 - 19.2 ft./lbs. 40.6 ft./lbs.Side Handle - 360 Degree -Chisel Rotation N/A VLM, 12 Angles N/APower Input 1140W 1,350W 1330WTool Length 22-1/4" 22-43/64" 34-23/32"Tool Weight 24.3 lbs. 23.1 lbs. 70.4 lbs.

SPECIFICATIONS NR90AD NR90AE NR90GRFastener Type Clipped Head, Full Round Head, Full Round Head,

Paper Strip Collation Plastic Strip Collation Plastic Strip CollationMagazine Angle 35 Degrees 21 Degrees 20 DegreesFastener Length Capacity 2" - 3-1/2" 2" - 3-1/2" 2" - 3/12"Fastener Diameter Range 0.113" to 0.148" 0.113" to 0.148" 0.120 - .131"Magazine Capacity (0.131") 86 (0.131") 64 37-42 NailsMagazine Loading Rear Rear RearAir Inlet 3/8" NPT Thread 3/8" NPT Thread -Operating Pressure 70-120 psi 70-120 psi -Depth Setting Tool-less Tool-less Allen WrenchActuation Selective Selective -Length 18-3/8" 18-3/16" 14-1/4"Width 4-29/32" 4-29/32" 4-1/4"Height 12-11/16" 12-11/16" 13-29/32"Actual Weight 7 lbs. 7.5 lbs. 7.9 lbs.Battery - - 7.2VBattery Life - - 4,000 NailsFuel Rod Life - - 1,200 NailsFeeder - - 2-Step

SPECIFICATIONS CR13VAmps 10No-Load Speed 0-2,800 SPMStroke Length 1-1/8"Keyless Blade Clamp YesTool Length 17-1/8"Tool Weight 7.3 lbs.

SPECIFICATIONS C7BMRAmps 15No-Load Speed 5,800 rpmFull-Load Torque 1.72 ft./lbs.Cutting Depth - 90Degrees 2-3/8"Cutting Depth - 45 Degrees 1-27/32"Cutting Depth - 50 Degrees 1-11/16"Cutting Depth - 55 Degrees 1-17/32"Electric Brake YesBase Materials Aluminum Die-CastSoft Grip Handles YesBevel Adjustment LeverBevel Capacity 55 DegreesWeight 10.5 lbs.

SPECIFICATIONS G18MRPower Source AC Single Phase, 50 or 60HzVoltage and Power Input 120V, 15Amp, 2,400WPower Output 980WMax. Power Output 3,500WNo-Load Speed 6000 rpmType of Motor AC Single Phase CommutatorEnclosure IDI-Internal Double InsulationType of Switch TriggerNo-Load Noise Level 88dBSpindle Thread 5/8" x 11Spindle Lock YesLength 19-3/8"Weight 11.9 lbs.

C7BMR 7-1/4"

CR13V

DH38YE

DH40MR

DH50MB

G18MRwith IDT Technology

SPECIFICATIONS DH38YE DH40MR DH50MBShank Spline SDS Max SDS MaxChuck Size 1-1/2" 1-9/16" 2"No-Load Speed 380 rpm 240-480 rpm 120-250 rpmImpact Rate 2800 bpm 1320-2650 bpm 1200-2500 bpmImpact Energy 5.2 ft./lbs. 7.4 ft./lbs. 3.7-13.3 ft./lbs.Amps 8 9.2 12.8Capacity: Drill Bit 1-1/2" 1-9/16" 2"Capacity: Core Bit 4-1/8" 4-1/8" 6-1/4"Modes of Operation Hammer/Hammer & Drill Hammer/Hammer & Drill Hammer/Hammer & DrillSwitch Electronic EVS EVSRHandle Type D D DFull Load Vibration - 117 db -No-Load Noise Level - 79.5 db -Power Input 870W 950W 1400WTool Length 17-15/16" 17-1/8" 19-1/2"Tool Weight 17.0 lbs. 14.3 lbs. 21.6 lbs.

H90SB1-1/8" Hex Demo Hammer

H60MRVDemolition Hammer

H55SCK3/4" Hex Demolition Hammer

HAMMER DRILLS

7" GRINDER

RECIPROCATING SAW

CIRCULAR SAW

BREAKERS

NR90AD

We carry a full line of Hitachi power tools. These are just a few...

NR90AE NR90GR

NAILERS

1184

-5-1

0

87

GRINDERS / DRILLS

WP8-115 Quick4-1/2" Angle Grinder withNon-Locking paddle switch.

WEP14-150 Quick “Deadman”Electronic 6" Angle Grinder/Cut-offMachine with non-locking paddle switch.

SSD18 LT1/4" Hex Impact Driver

SB18 LT18V Hammer Drill/Driver

GRINDERSWP 8-115 Quick WEP 14-150 Quick

Grinding wheel 4-1/2" 6"Torque 19.5 in.-lbs. 31 in.-lbs.No-load speed 10,000 /min. 9,000 /min.Rated input power 800 W 1400 WSpindle thread 5/8" - 11 5/8" - 11 Weight 5.3 lbs. 6.1 lbs.

CORDLESS DRILLSSB 18 LT SSD 18 LT

Type of battery pack/Voltage Li-Ion/18 V Li-Ion/18 VCapacity of battery pack 2.6 Ah 2.6 AhMax. impact rate 28000 /min. level 1 / 2 / 3 1500/2700/3300 /min.Max. torque 239 in.-lbs. soft/ level 1 / 2 / 3 708/1106/

549 in.-lbs. hard 1416 in.-lbs.Drill diameter in - Concrete 1/2"- Steel 1/2"- Wood 1-3/16"

No-load speed 0 - 400 / 0 - 1400 /min level 1 0 - 1600 /min.level 2 0 - 2150 /min.level 3 0 - 2650 /min.

Drill spindle thread 1/2" -20 UNFBit retainer Hexagon recess 1/4" (6.35mm)Chuck capacity 1/2" –Weight (w/battery pack) 4.4 lbs. 4 lbs.

HAMMER DRILLSKHE-D 24 KHE-D 28 KHE 56

Torque 106 in.-lbs. 177 in.-lbs. 796 in.-lbs.Drill diameter in - in concrete w/solid bits 1" 1-1/8" 1-3/4"- in mild steel 1/2" 1/2" 1-1/8"- in softwood 1-3/16" 1-9/16" 2-9/16"- Concrete w/core bits – – 4"No-load speed 0 - 1000 /min. 0 - 1000 /min. 450 /min.Rated input watts 720 1010 1300Max. impact rate 4600 /min. 4600 /min. 2840 /min.Max. single impact energy 2.2 J 2.5 J 14 JWeight (without mains cable) 7.4 lbs. 8.1 lbs. 17.75 lbs.Length 16-3/4" 18" 18"

KHE 56

KHE-D 24

3

147-

17-1

0

88

UTILITY KNIVES / PIPE WRENCHES

ProTouch™ Retractable Knife• Quick change mechanism allows for easy blade removal without opening the knife.• Smooth, three-position slide provides increased durability for frequent use.• Easy tool-free entry with push button operation opens the knife and exposes

replacement blades.• Features inside storage for up to 5 blades.• Includes 3 IRWIN BLUE BLADE™ Bi-Metal Utility Blades.

ProTouch™ Fixed Knife• ProTouch™ ergonomic grip.• Optimized cutting angle for reduced fatigue.• Easy tool-free entry.• Features inside storage for up to 5 blades.• Includes 6 IRWIN BLUE BLADE™ Bi-Metal Utility Blades.

Standard Safety Knife• Self-retracting spring action returns blade safely into the housing when not in use.• Interlocking nose reduces blade wobble.• Ergonomic grip fits comfortably in the hand.• Two blade positions – 2mm extension for box cutting and full extension for general use.• Tool-free entry.

Item No. 2082200

Item No. 2081200

Item No. 2088600

Bi-Metal BLUE BLADE™ Utility Blades

Item No. 2084400 - 100-Pack IRWIN BLUE BLADE™ Bi-Metal Utility Blades

• Features patented Bi-Metal technology that sets new standards of performance.• UNBREAKABLE: Spring steel body delivers superior flexibility to prevent

breaking (under normal working conditions).• LASTS LONGER: High speed steel cutting edge stays sharp longer than

traditional carbon utility blades (tested on 20 lb. recycled paper).• Fits most utility knives.

• Constructed from the highest grade cast iron, forged and heat treated to ensure maximum durability.

• Unique hammer head design provides a flat surface for hammering.• Easy-spin adjusting nut is heat-treated for durability.• Wide I-beam handle design provides better weight distribution.• Drop-forged jaw is heat-treated to resist distortion or breakage.• Hardened teeth provide tremendous bite.• Housing constructed of heavy-duty cast iron.

Quick Adjusting Pipe Wrench• The Quick Adjusting Pipe Wrench is built with convenience and durability in mind.• One-handed operation enhances user’s speed and convenience. Ratchets quickly to

work surface.• Smooth release upon job completion.• Broached teeth are ideal for most surfaces including black, galvanized, PVC

and copper pipe, as well as nuts, bolts and couplings.• 43% less weight than standard 14" cast iron pipe wrenches.• Ergonomic handle ideal for heavy torque and maximum comfort.• Riveted to heat treated steel body.

Cast Aluminum Pipe Wrench• Heavy-duty cast aluminum housing is 40% lighter than cast iron and

easier to maneuver.• I-Beam handle and wide design provide better weight distribution.• Drop-forged jaw is heat-treated to resist distortion or breakage.• Easy-spin adjusting nut is heat-treated for durability.• Hammer head design provides a flat surface for hammering.• Features a Lifetime Guarantee.

Item No.Jaw

Capacity Length

274101 1-1/2" 10"

274102 2" 14"

274103 2-1/2" 18"

274104 3" 24"

274105 1" 8"

274106 2" 12"

274107 5" 36"

274108 6" 48"

Cast Iron Pipe Wrench

Item No.Pipe

Capacity Length 2074110 1-1/2" 10"

2074112 2" 12"

2074114 2" 14"

2074118 2-1/2" 18"

2074124 3" 24"

2074136 5" 36"

2074148 6" 48"

Item No.Jaw

Capacity Length274001 2-1/4" 11"

147-

18-1

0

89

PIPE CLAMP / METAL AND MASONRY DRILL BITS

Quick-Grip Pipe Clamps• Innovative clutch system eliminates the need for threaded pipe.• Larger feet offer more stability and clearance between handle and worktop.• Larger, more ergonomic handle offers easier clamping with reduced hand fatigue.• Larger clutch plates allow for easier release and increased durability and dependability.

Item # Throat Depth Pipe Size224212 1 1/2" (37 mm) 1/2" (12 mm)224134 1 7/8" (47 mm) 3/4" (19 mm)

Black & Gold HSS Fractional Straight Shank Jobber Length Drill Bits

• Laser-etched markings for easy identification.• High Speed Steel features a black shank and gold flute.• Heavy-duty web construction for strength and durability.• 135Â° split point begins drilling immediately, minimizing bit “walk.”• 3-Flatted shank on 3/16" and above for better chuck grip.• Provides accurate drilling without a center punch.

Black & Gold HSS Fractional 3/8" Reduced Shank Jobber Length Drill Bits

• High Speed Steel features a black shank and gold flute.• Heavy-duty web construction for strength and durability.• 135Â° split point begins drilling immediately, minimizing bit “walk.”• Accurate drilling without a center punch, for general metal drilling.

Item # Size Twist Length Overall Length 3019125B 25/64" 3-3/4" 5-1/8"3019126B 13/32" 3-7/8" 5-1/4"3019127B 27/64" 3-15/16" 5-3/8"3019128B 7/16" 4-1/16" 5-1/2"3019129B 29/64" 4-3/16" 5-5/8"3019130B 15/32" 4-5/16" 5-3/4"3019131B 31/64" 4-3/8" 5-7/8"3019132B 1/2" 4-1/2" 6"

Item # Size Twist Length Overall Length 3019003B 3/64" 3/4" 1-3/4"3019016B 1/4" 2-3/4" 4" 3019015B 15/64" 2-5/8" 3-7/8" 3019014B 7/32" 2-1/2" 3-3/4" 3019013B 13/64" 2-7/16" 3-5/8" 3019012B 3/16" 2-5/16" 3-1/2" 3019011B 11/64" 2-1/8" 3-1/4" 3019010B 5/32" 2" 3-1/8" 3019009B 9/64" 1-3/4" 2-7/8" 3019008B 1/8" 1-5/8" 2-3/4" 3019007B 7/64" 1-1/2" 2-5/8" 3019006B 3/32" 1-1/8" 1-1/4" 3019005B 5/64" 1" 2" 3019004B 1/16" 7/8" 1-7/8" 3019017B 17/64" 2-7/8" 4-1/8"3019018B 9/32" 2-15/16" 4-1/4"3019019B 19/64" 3-1/16" 4-3/8"3019020B 5/16" 3-3/16" 4-1/2"3019021B 21/64" 3-5/16" 4-5/8"3019022B 11/32" 3-7/16" 4-3/4"3019024B 3/8" 3-5/8" 5"3019025B 25/64" 3-3/4" 5-1/8"3019026B 13/32" 3-7/8" 5-1/4"3019027B 27/64" 3-15/16" 5-3/8"3019028B 7/16" 4-1/16" 5-1/2"3019029B 29/64" 4-3/16" 5-5/8"3019030B 15/32" 4-5/16" 5-3/4"3019031B 31/64" 4-3/8" 5-7/8"

Clay Spade

Moil Point

Flat Chisel

Scaling Chisel

Wide Scaling Chisel

Ground Rod Driver

Asphalt Cutter

Bush Tool - 1-Piece

Metal Drilling Bits

Masonry Drill Bits

3

147-

19-1

0

90

MASONRY DRILL BITS

• Patented flute design.• Patented carbide tip.• Short drill head.

Spline Standard / Multi-Cutter

• Fits all spline rotary hammers.• Patented flute geometry removes dust from the hole quicker for fast

drilling and long life.• Shot-peened, double-tempered finish reduces breakage.• Copper braze material gives high heat resistance for reduced tip loss.• All tips made to ANSI specifications.• Chrome vanadium shaft through-hardened to 50-53HrC.

SDS-max Standard / Multi-Cutter

• Fit all SDS-max and Hilti TE F/G and Y rotary hammers.• Patented flute geometry removes dust from the hole quicker for

fast drilling and long life.• Shot-peened, double-tempered finish reduces breakage.• Copper braze material gives high heat resistance for reduced

tip loss.• All tips made to ANSI specifications.• Chrome vanadium shaft through-hardened to 50-53HrC.

• 2X longer life than traditional masonry bits.• Maximized flute for faster, more efficient dust removal.• 2X more carbide in tip for 2X longer drilling life in

rebar-reinforced concrete.• Optimal groove design minimizes friction for increased speed

and longer life.• Blue power ring for easier identification in the toolbox.• Premium steel improves core strength for maximum durability

and extended life.

SDS-plus Standard / Hex Drive / Multi-Cutter

• Fits all SDS-plus and Hilti TE-C rotary hammers.• Reduced area above the flute prevents the drill bit from binding

while drilling – the full usable length can be utilized.• Chrome vanadium shaft through-hardened to 50-53HrC.• Patented tip and flute design removes dust more efficiently –

up to 25% faster than other bits.• Shot-peened, double-tempered finish reduces breakage.• Hot isostatically pressed to extend life and resist breakage.• Copper braze material gives high heat resistance for reduced

tip loss.• All tips made to ANSI specifications.

• Fit all spline rotary hammers.• Delivers power to the tips more efficiently than 2-piece designs.• Reduces breakage and other problems associated with

2-piece designs.• Maximum drilling depth is 2-5/8".

• Fits all hammer drills with 3-jaw or Jacobs chuck.• Chrome vanadium shaft through-hardened to 50-53HrC.• Patented flute geometry removes dust from the hole quicker for

fast drilling and long life.• Up to 150% faster than other competitive bits.• Shot-peened, double-tempered finish reduces breakage.• Hot isostatically pressed to extend life and resist breakage.• Copper braze material gives high heat resistance for reduced

tip loss.• All tips made to ANSI specifications.

Core Bit Spline Shank

Core Bit SDS-max Shank

• Fit all SDS-max and Hilti TE F/G and Y rotary hammers.• Delivers power to the tips more efficiently than 2-piece designs.• Reduces breakage and other problems associated with

2-piece designs.• Maximum drilling depth is 2-5/8".

Rotary Percussion - Straight Shank

Multi-Material Bits

• Designed to drill in multiple materials including brick, block, tile,metal, wood, plastic and marble.

Rotary Drill Bits

Glass and Tile Masonry Drill Bits

41

FormsTies & AccessoriesNail Stakes & Pins

Curb & Gutter FormsConcrete Texture Mats

Color Hardener Concrete Stain

Curing, Sealants and Form ReleaseJoint Filler

WaterproofingBar Supports

Bridge HangersLight Forming Accessories

Medium/Heavy Forming AccessoriesWire

Concrete Forming & Accessories 2

PRECISE FORMS, INC.PRECISE FORMS, INC.

CONCRETE ACCESSORIES

innovating concrete construction

®

2084

-10-

10

CONCRETE FORMING SYSTEM

UNI-PLY Multi-Purpose Handset Form System

UNI-PLY PANEL DETAILS PSI 1000 MAX

� Exact corner joints eliminate tolerance build-up over large areas.� Standard 220/220 Xact2form* Birch Plywood is riveted to the angle

struts. The mill quality system is certified according to the interna-tional standard ISO 9001, and meets or exceeds the following international standards: PSI-95 United States of America, BFU 100DIN 68705 Germany TU, 5512-002-002273235-95, STP 17-02-97Eastern Europe.

� Side and end rails are rolled form 55,000 psi steel and welded continuously at corners for maximum strength.

� Angle struts are spaced on 12" centers to provide strength,uniform concrete and minimize deflection.

� Handles are provided on panels for easy handling in settingand stripping forms.

� Two inch wide angle strut provides greatest frame andplywood strength on the market.

� Dado slots on face of form allow tie spacing at 12" on center.Rear, side and end rail dados are located at 6" on center to allowoptimum accessory location. Front-side and rear-side rail contactpoints prevent grout seepage and permit true form alignment withadjacent panels. Rated for a 1000 lb./ft.2 (psf) rating at a 2:1 safetyfactor. Metric forms available.

*Xact2form – Plywood panels are designed for superior performanceand appearance grade concrete forming. It is a 100% birch panel offering LONG and SHORT GRAIN face directional veneer in a multi-ply construction.

1

2

3

4

5

67

Description Width (inches) Height (feet)

Panels 24 3, 4, 5, 6, 8, 9, 10

Fillers 4 to 22 3, 4, 5, 6, 8, 9, 10

Metal Fillers 1, 1.5, 2 3, 4, 5, 6, 8, 9, 10

Inside Corner 6x6, 4x4 3, 4, 5, 6, 8, 9, 10

Outside Corner 3, 4, 5, 6, 8, 9, 10

Filler Angles 3, 4, 5, 6, 8, 9, 10

Pilaster Panels 3, 4, 5, 6, 8, 9, 10

Culvert Forms 3, 4, 5, 6, 8, 9, 10

Inside & Outside Bay Corners 3, 4, 5, 6, 8, 9, 10

Hinge Corners 3, 4, 5, 6, 8, 9, 10

UNI-PLY PANELS AND FILLERSAvailable in wood, steel and job-built options (for odd dimensions)

42

2084

-11-

10

CONCRETE FORMING SYSTEM

Universal offers a variety of Loop Ties andAccessories to use with your UNI-PLY PanelHandset System. Safety Factor on all ties: 2:1

HANDSET LOOP TIEStandard 1" breakback. Available in standard and heavy-duty load ratings.

GANG SET LOOP TIELonger in length. Standard 1” breakback. Available in standard and heavy-duty load rating.

COIL COMBINATION TIEAvailable with snap tie or loop tie ends. This tie has a one end as a tie and other ad a coil insert. Used for adding thickness to an already standing wall.Used with drop-in coil anchor.

BASE TIENo breakback. Used to span across the base to two opposite steel forms for the purpose of establishing the desire wall thickness.

WALER TIENo breakback, loop end. Used to tie a z-tie holder and double wales to thesteel forms when the wales are running vertically.

HANDSET FLAT TIEStandard 1/2" breakback. Available in standard and heavy-duty load ratings.

WATER RESISTANT NEOPRENE WASHEROptional part applied to ties to help prevent water leakage down the length of the tie.Special combination ties available upon request.

UNI-PLY ASSEMBLY ACCESSORIES

Basic Components

Also available through Universal:• Strongback ties and j-hooks• Gang form bolt• Short bolt• Gang waler rod and plate• Plywood brace attachment plates• Concrete hoppers and elephant trunks• Form stripping bars• Standard stakes and fence t-posts

One PieceWaler Clamp

“Z” TieHolder Bracket

Waler Brackets for alignment

“S” Wedge

Long BoltWedge Bolt

Scaffold Jack BracketMini BraceTurnbucklesStraight or bent plate

43

2

2313

-5-1

0

ALUMINUM FORMS

44

PRECISE FORMS, INC.PRECISE FORMS, INC.

Create fantastic lookingwalls every time with

Precise Smooth Aluminum.ExperiencedLeader

Precise Forms hasbeen the leader inproducing aluminumforms since 1967.

Our forms areused for:

BasementsRetaining WallsWarehousesApartmentsFactoriesBridgesCulvertsPrecastScreening WallsOfficesPumping StationsStorage TanksManure PitsLight Commercial... and much more!

• Light weight, a 36"x96" is approximately 75 lbs.• Corner gussets for support.• Full line of fillers.• Optional Set&Lok and Captive Pin.• Specially designed siderails.• Inset endrails.• State of the art robotic welding.

Precise Forms was the first company to introduce the 0.125 thickface sheet which has become the market standard. Our speciallydesigned side rail provides greater strength and durability to theform while protecting and supporting the face sheet.

Corner Gussets are used tostrengthen the corners as wellas to minimize concrete build-up thus providing a stronger,longer lasting form. Preciseuses a serrated 4" channelbracing on all of our 6-12 holepattern forms. This provides abetter gripping surface on thewider cross members.

Precise Forms produces an alu-minum form with an inset end railthat allows the sheet to inset. Thisinset end rail adds strength to theform and additional face sheetsupport without unsightly lines tothe vertical form joints.

3105

-1-1

0

45

FORMS

Barrier

Curbs

Flexible Curb and Gutter

Flexible Sidewalk

Specialty

Standard Paving

Straight Sidewalk

Super Curb and Gutter

Super Flat

Wide Base

Jaquith manufactures the high strength BMF Metal Forms or Metal Concrete Forms used to form concrete sidewalks, curbs and gutters, runways, roads, median barriers, bridge parapets and slabs for industrial, residential and commercial applications.

All BMF forms are sheared, punched, assembledand welded with maximum strength and rigidity

for easy setup, stripping and re-use-features that save a contractor money and greatly

reduce construction time.

CURB & GUTTER FORM

Curb Back Form

Taper Key

Gutter Form

Curb FaceForm

Full DivisionPlate

Flexible Curb and Gutter Form

Paving Forms

Adjustable Height Form

2

167-

4-10

NAIL STAKES & PINS /FLAT WORK FORMSCONCRETE ACCESSORIES

SteelFORMPINSforSTEELFORMS3/4" DIA. STANDARD STAKES

for general construction

7/8" DIA HEAVY DUTY STAKESfor heavy construction

LENGTHS:12", 18", 24", 30", 36", 42", 48"

& longer

The fastest wayto remove deeNail Stakeswithout damageis to use a deeStake Puller.

Featuresdee Nail Stakes have 12 spirally arranged nail-ing holes one inch on center, giving each stake24 prelocated nail entry points. No matter howthe dee stake rotates or angles, you’ll still findat least one hole that will allow you to firmlyanchor the stake to the form board. Further, thehole keeps the nail in place during alignment,leaving both hands free to bring the form boardto the line and hammer the nail.

Increase production – boost profitsEvery dee Nail Stake saves 3 minutes or morein form board installation. You can save 30¢with each dee Nail Stake you use. A 24" deeNail Stake will pay for itself in five uses or less.

Every dee Nail Stake has an average life ofmore than 200 uses, and their solid steelrigidity allows you greater stake spacing. deeNail Stakes do away with splitting, twisting andsplintering and require only one nail per stake,practically eliminating form board damage.

ESSENTIAL TOOLS FOR EVERY CONTRACTOR

STAKE PULLERS

FLAT WORK FORMS (4", 5", 6", 7" high – 10' long)Self-aligning steel forms that require no latching, locking or fitting, just slide the solid nose into the reinforced box end at anyangle, drive the form pin thru the pocket, sock the wedge home and forming is complete. Two men can completely set up1,000 feet of form, 500 feet of sidewalk, straight as a die, in two hours, ready for concrete.

255 - STRAIGHT FILLER FORM

559 - Male 560 - FemaleTRANSITION FORMStraight to Flexible

507 - FLEXIBLE FORM

259 - CORNER FORMSInside

322 - DIVISION PLATE

101 - COLD ROLLEDSOLID STEELNAIL STAKES

257 - CORNER FORMOutside

205 - STRAIGHT FORM

It’s as simple as ABC and dee®

Steel NAIL STAKES• FOOTERS• EDGE FORMS• CURBS & GUTTERS• FLATWORK

• SIDEWALKS• DRIVEWAYS• PATIOS

• FOOTERS• POOLS• LANDSCAPING

Corner forms provide the ability topour clean right angle corners forpatios, pads and walkways.

Filler forms provide the ability toconnect forms for odd size pours.

Radius forms prove the ability to pourserpentine walkways andcircular structures.

Slip-On Form Spreaders speed upform setting – they automaticallydimension the form. Just stake theforms to line on one side. To set theother side place a spreader at each endof a ten foot section, bring that form toline using the spreader as a template,lock it to the form pins and move thespreader ahead as forming continues.If Division plates are specified for coldjoints, they are spaced as required.4" to 12" high – any length

Flexible Forms are ideal for all typesof radius forming. Only dee FlexibleForms have 7 stake pockets andwedges to insure positive radius form-ing and to prevent flows between thepockets. Angles attached to the ends ofthe forms and locked with the clampskeep the forms properly aligned at thejoints. Forms 4" to 7" high have 7' sin-gle wedge pockets.

dee Transition Forms provide an ideal way to make a smooth transition fromstraight forms to flexible forms. Always order in pairs, male and female.

LOCKING CLAMP

FEMALEMALE

12"12"

Form Ht.Form Ht.

46

167-

5-10

STEEL FORMS,CURBS AND GUTTERSCONCRETE ACCESSORIES

STEEL FORMS – The most accurate method of forming for Curbs and Gutters

FLEXIBLE FORMS for RADIUS FORMINGfor step type curbs and gutters with a batter and radius

dee Steel Curb and Gutter Forms are the most modern forms now in use in the construction industry. They are self-aligning,making form assembly faster and easier. No latching, locking or fitting is required. The only moving parts are the heavy-dutywedges that securely lock the forms in place on the form pins and keep them to line regardless of subgrades. dee SteelCurb and Gutter Forms can be set up and stripped easier and faster than any other form on the market. Three men cancompletely set up 1,800 feet of forms in two hours, ready for concrete, equal to 300 feet of form per man hour.

Heavy duty pockets and wedgeswelded to the form securely lockthe forms to 3/4" or 7/8" stakes.

Intermediate braces are weldedto all forms to provide maximumstrength, eliminate form damage.

With the front and back flexi-ble forms in place the divi-sion plates are installed, thenthe flexible curb face formsare slipped into the clips andlocked to the division plates.End angles and lock clampslock the sections together tomaintain alignment at theform joints.

We suggest one full divisionplate and 5 skeleton divisionplates for each 10-foot sec-tion of form to insure themost accurate forming.

All you need for 100 L.F.

• 10 pcs Back Forms

• 10 pcs Gutter Forms

• 10 pcs Curb FaceForms

• 20 pcs TopSpreaders

• 11 pcs Full DivisionPlates

• 50 pcs 3/4" x 24"Form Pins

Hi-strength steel form pins willdrive thru any subgrade, willabsolutely hold the forms to line.

Heavy-duty noses slide into the box endsfor fast self-aligning form assembly withoutfitting, latching or locking.

Curb face forms slip into thehold down clips, no thread-ing, wedging or locking; rapidstripping.

Smooth rails and faces, no slots ornotches, concrete seepage is eliminated,fast easy finishing.

Top spreaders lock the curb faceform to the back face form.

Heavy steel angles welded atboth ends of all forms providea solid box end, completelyeliminate end damage.

4 bolt holes in each rail provide forrapid, easy attachment of variousforming accessories.

Slip-on division plates drop over therails at any position.

5 steel braces are welded to the curbface forms for maximum strength.

Double flanges top and bottomprovide greater rigidity, leave clearunobstructed working areas.

Battered Face

Battered Face with Single Radius

Battered Face with Double Radius

The only system of radius forming that cuts forming and finishing costs 80% or more since it provides a flexible curb faceform with a batter and a radius to conform to the exact profile of the straight curb and gutter – just lap the flexible forms atthe end of the straight forms and continue forming. This unique flexible curb face form consists of 1-foot segments thatrotate on a center rivet with free floating rods at the top and bottom to reinforce the forms and to insure inward or outwardcurvatures of the exact profile required.

FLEXIBLE CURB FACE FORMS10' long – 4", 5", 6", 7", 8" high

FLEXIBLE BACK AND FRONT FORMS10' long – 4" to 24" highMinimum radius – 18"

Hold DownClip

RotatingClip

CurbFace

47

2

PRODUCT PACKAGING COVERAGE

Achieve stunning detail and flawlessdesign with the complete line of Butterfield Color Decorative ConcreteProducts. At Butterfield Color we havedeveloped Decorative Concrete Stamping,Coloring and Staining Systems to meet the demands of our customers.

QUICK REFERENCE GUIDE

3014

-1-1

0

DECORATIVECONCRETE PRODUCTS

48

EEnnggiinneeeerreedd CCoonnccrreettee PPeerrffoorrmmaanncceeEEnnggiinneeeerreedd CCoonnccrreettee PPeerrffoorrmmaannccee

INTEGRAL COLORUni-Mix® Integral Color (5 Sack) Dissolvable Bag 1 Bag Per Cubic YardUni-Mix® Integral Color (6 Sack) Dissolvable Bag 1 Bag Per Cubic YardUni-Mix® Liquid Integral Color 1, 2, 3.5 gal. Pails Varies by WeightSelect Grade™ Integral Color Dissolvable Bag 1 Bag/2 cu. yd., 1 Bag/cu. yd., 2 Bag/cu. yd., 3 Bag/cu. yd.COLOR HARDENERPerma-Cast® Shake-on Color Hardener 60 lb. Square Pail Dark Colors: 100-125 SF, Light Colors: 80-100 SFRELEASE AGENTSPerma-Cast® Antiquing Release 30 lb. Pail 1,000-1,200 SFPerma-Cast® Antiquing Release Mini Pack 1 lb. Pack 30-40 SFClear Liquid Release 5 gal. Pail 750 SFSelect Grade™ Antiquing Release 30 lb. Pail 850-1000 SFSTAINPerma-Cast® Sierra Stain™ 1 gal. Jug 300 SF (mixed w/1 gal. Potable Water)Renovatio™ Concrete Stain 32 oz. Kit 500 SF (3 Part Kit mixed w/128 oz. Potable Water)Renovatio™ Concrete Stain 16 oz. Kit 250 SF (3 Part Kit mixed w/64 oz. Potable Water)Renovatio™ Concrete Stain 4 oz. Kit 62 SF (3 Part Kit mixed w/16 oz. Potable Water)Elements™ Transparent Stain 32 oz. Unit 200-400 SF (mixed w/96 oz. Potable Water)Elements™ Transparent Stain 4 oz. Unit 25-50 SF (mixed w/12 oz. Potable Water)VERTICAL WALL MIXCantera™ Vertical Wall Mix 35 lb. Bag Approx. 8 SF at 1" thicknessOVERLAY MATERIALST-1000™ Stampable Overlay (Cement Gray) 55 lb. Bag 16 SF @ 3/8" average depthT-1000™ Stampable Overlay (Cement White) 55 lb. Bag 16 SF @ 3/8" average depthT-1000™ Fine: Sprayable Application (Cement Gray) 55 lb. Bag 48 SF @ 1/8" average depthT-1000™ Fine: Sprayable Application (Cement White) 55 lb. Bag 48 SF @ 1/8" average depthT-1000™ Fine: Repair Application (Cement Gray) 55 lb. Bag 96 SF @ 1/16" average depthT-1000™ Fine: Repair Application (Cement White) 55 lb. Bag 96 SF @ 1/16" average depthT-1000™ Color Pack (Available in Uni-Mix Colors) Bag 1 Bag Per 1 Bag of T-1000T-1000™ Primer 1 gal. Jug 400 SF (mixed with water)STENCILSNon-Adhesive Stencils 1,000 SF Roll (4' x 250') 900 SF after cuttingAdhesive Stencils 500 SF Roll (3' x 167') 400 SF after cuttingNon-Adhesive Mini Roll Stencils 100 SF Roll 90 SF after cuttingNon-Adhesive Soldier Course Stencils 300' Roll 295 LF after cuttingAdhesive Soldier Course Stencils 300' Roll 295 LF after cuttingSURFACE RETARDERSSurfEtch™ Top Surface Retarder 1 gal., 5 gal. 35-60 SF/GAL, 175-300 SF/GALCURING & SEALING FINISHESClear Guard® Cure and Seal 1 gal., 5 gal., 55 gal. Curing: 200 SF/GAL Sealing: 200-400 SF/GALClear Guard® H2O Cure & Seal 1 gal., 5 gal. Curing: 200 SF/GAL Sealing: 200-400 SF/GALClear Guard® H2O Wet Look 1 gal., 5 gal. Sealing: 200-400 SF/GALColor Guard™ Solid Cure and Seal 1 gal., 5 gal. Curing: 200 SF/GAL Sealing: 200-400 SF/GALColor Guard™ Translucent Cure and Seal 1 gal., 5 gal. Curing: 200 SF/GAL Sealing: 200-400 SF/GALSharkGrip Non-Skid Additive 1 lb. 1 lb. Per 5 gal. of Clear Guard®

Flattening Paste 1 qt. 1 qt. Per 5 gal. of Clear Guard®

COUNTERTOP MIXFlat Out® Countertop Mix 55 lb. Bag 4.75 SF @ 1"Flat Out® Polymer 5 gal. Pail Approx. 3.25 Quarts per 55 lb. Bag of Flat Out® Countertop Mix

All Coverage Ratesmy vary depending on jobsite conditions.for actual coveragerates jobsite mock-upsmust be completed.

3014

-2-1

0


49

Clear Liquid ReleaseButterfield Color Clear Liquid Release is abond breaker used with stamping mats,texturing skins or texture rollers prior toimprinting concrete or cementitious overlays.It prevents the stamping or texturing tool fromsticking to the surface, enhances the transferof the detailed pattern and texture and pro-longs the surface life of the stamping mat ortexturing tool. Use on integrally colored oruncolored concrete, shake-on color hardenersand stampable cementitious overlays. It issuitable for outdoor and indoor use.Clear Liquid Release is particularly useful withoverlays since it will not contaminate the existing concrete substrateas readily as powdered releases. It evaporates quickly and requireslittle to no clean up prior to applying solvent based curing and sealingcompounds such as Clear Guard® Cure and Seal, or prior to chemicalstaining with Perma-Cast® Sierra Stain™. VOC content is less than450 g/L (3.75 lb./gallon).

Perma-Cast® Sierra Stain™Perma-Cast® Sierra Stain™ is a pene-trating, reactive stain that chemically

combines with cured concrete toproduce permanent, variegatedcoloring effects. Perma-Cast®

Sierra Stain™ is suitable forexterior hardscapes, artificial rockformations, interior floors, walls,statuary and counter tops. Expectwide color variations, mottling and

unevenness of the color. Each application ofPerma-Cast® Sierra Stain™ produces unique results. Apply to clean,sound concrete or cementitious overlays. Different stain colors may beused in combination for more coloration affects. In addition, many fauxfinishing techniques used with paints, can be utilized with chemicalstains. Introduce saw cuts to create patterns and graphics in thesubstrate before staining. For truly unique and creative concreteinstallations, use of Perma-Cast® Sierra Stain™ can be combinedwith other Butterfield Color products.

Perma-Cast® Antiquing ReleaseButterfield Color Perma-Cast® AntiquingRelease is a pigmented powder bondbreaker used with stamping mats, texturingskins and texture rollers. It also provides

accent colors that compliment or contrastwith the underlying concrete surface.Additionally, it enhances the transfer of thedetailed pattern and texture, and prolongsthe surface life of the stamping mat ortexturing tool. It is compatible with Uni-Mix®

Integrally colored concrete, Perma-Cast®

Shake-on color hardened concrete and T1000™Stampable cementitious overlays.

Perma-Cast® Antiquing Release is a finely ground, streak free powderthat is a blend of UV-resistant pigments and water repelling additives.It is broadcast over the concrete surface prior to placing the stampingor texturing tools. As the imprinting tool is pressed into the plasticconcrete surface, a portion of the Perma-Cast® Antiquing Releaseis embedded into the textured surface of the concrete.Perma-Cast® Shake-on Color Hardener

Perma-Cast® Shake-on Color Hardener is a dryshake color hardener that is applied to the sur-face of freshly placed concrete. It is a cementi-tious-based coloring material that may be usedto create abrasion resistant interior floors andfreeze-thaw stable exterior hardscapes.The time-tested formulation of Perma-Cast®

Shake-on Color Hardener creates anextremely dense surface that is resistantto foot and vehicular traffic and extremeweather. It is available in a wide range ofstreak free, uniform colors ranging fromsubtle pastels to deep, rich hues. It isused to uniformly color gray concrete, or provide random accents of color on concrete integrally colored with Uni-Mix®

Integral Colorant or Uni-Mix® Liquid.Perma-Cast® Shake-on Color Hardener is a precise blend of cement,silica quartz aggregates, synthetic iron oxides and plasticizer. Perma-Cast® Shake-on Color Hardener conforms to ASTM Standard C979for color stability.

EEnnggiinneeeerreedd CCoonnccrreettee PPeerrffoorrmmaanncceeUni-Mix® Integral ColorantUni-Mix® Integral Colorant is a premeasured admixture for integrally coloring ready mixedconcrete during batching. Conforming to ASTM Standard C979 (StandardSpecification for Pigments for Integrally Colored Concrete), it is a blend of non-fading, synthetic iron oxides and a water-reducer, which produce uniform, streak-free colors in concrete.The water-reducer in Uni-Mix® Integral Colorant allows the color to quickly and evenly disperse without additional water, thereby maintaining the strength and freeze/thawresistance of the cured concrete. This same component improves the finishing characteristics of the concrete, which contributes to color uniformity and surface durability. Superior quality control during manufacturing and packaging help to ensure your jobs will have uniform color from load-to-load. Uni-Mix® Integral Colorant is suitablefor all concrete flat work installations, interior floors and exterior hardscapes, as well as precast, tilt-up and cast-in-place applications.

Uni-Mix® Liquid Integral ColorantUni-Mix® Liquid is a preciseblend of concentrated syntheticiron oxide pigments, disper-sants, and stabilizing agents.By stocking only 4 or 5 basecolors, a wide range of colorsare possible with the press of a button. Benefits include offering color on demand while reducing inventory.With both batch plant and bucket dispensing systemsavailable, a Butterfield ColorUni-Mix® Liquid System easilyallows and quickly providesstandard and custom colors. Butterfield Color Uni-Mix® Liquid dispensing systems are pre-programmed with Butterfield Color formulas, as well as those of other major color manufacturers.New color formulations are available on a continuing basis.Butterfield Color’s Uni-Mix® Liquid Color offers a premium quality product, backed by unmatched customer service. From the initialmachine selection and start-up, to training and service, ButterfieldColor is here to assist each step of the way.

2

T1000™ Fine OverlayT1000™ Fine Overlay is a polymer modi-fied cementitious topping formulated forresurfacing structurally sound, non-moving concrete floors, walls and exterior hardscapes. The cured productcreates an abrasion resistant surface suitable for pedestrian and automobile traffic. It is an ideal system for restoringworn or color blemished concrete, or correcting construction errors. T1000™ FineOverlay is a precise blend of graded sand,cement and polymer, which allow for thin applications. It can besmooth troweled, broom finished or applied using a splatter brush orhopper gun for a knock down finish with Butterfield Color® Stencils.Application thickness ranges from 1/16 inch (1.5mm) to a maximum of3/16 inch (4.5mm). T1000™ Fine Overlay is pre-packaged in mediumgray or white.

Renovatio™ Concrete StainRenovatio™ Concrete Stain is a high performance, polymerizedcoloring stain. It is a concentrated, three-component system thatpenetrates and bonds within the porousconcrete substrate. It provides a uni-formly colored, no gloss, abrasionresistant surface, suitable for coloringexisting interior concrete floors andexterior concrete hardscapes. It canbe used to recolor unsealed decorativeconcrete or to renovate weatheredor discolored concrete surfaces. A com-panion product, Renovatio™ Translucent Accent Stain, createstranslucent variegated color or antiquing effects on stamped or tex-tured surfaces. Renovatio™ Clear Seal can be applied for additionalprotection or a gloss finish over Renovatio™ Concrete Stain andRenovatio™ Translucent Accent Stain. Renovatio™ products arebreathable and freeze/thaw resistant. They are low odor, water-based,environmentally and user-friendly concrete staining systems.

3014

-3-1

0


50

Cantera™ Vertical Wall MixCantera™ Vertical Wall Mix is a pre-pack-aged lightweight overlay system for verticalsurfaces. It can be trowel applied and thenstamped, textured or sculpted by hand tomimic natural stone construction.Application thickness ranges from 1/4 inch toa maximum of 1 inch in a single application.

Stamping ToolsButterfield Color® has built its reputation on quality and reliability. Allof our stamping and texturing tools have been designed and precision

manufactured to perform to the expectations that our40 years of field experience provides. Each stamping

tool is molded using the actual stone,brick or wood that it recreates. Withover 50 stamp patterns available,our tools are designed to minimizerepetition, surface cracking andblowouts along grout lines, thus pro-ducing realistic and natural appearing

installations, reducing the touch-up time, andincreasing production capabilities. The tools can beused on fresh concrete or cementitious overlays.

T1000™ Stampable OverlayT1000™ Stampable Overlay is a polymermodified cementitious topping formulatedfor resurfacing structurally sound,non-moving concrete floors and exterior hardscapes. The overlay provides adurable surface suitable for stamping withButterfield Color® Stamping Tools or textured with Butterfield Color® TextureRollers. The cured product creates an abrasion resistant surface suitable forpedestrian and automobile traffic. It is anideal system for restoring worn or color-blemished concrete, out of level surfaces or correcting construction errors.

Form & Step LinersForm and Step Linersby Butterfield Colorhave been designedfor efficiency andaesthetic appeal.The polyurethane formliners can be easilyattached and arecompatible withstandard 1-1/2 inchdimensional foam orform lumber. The Cut Stone Form Liner series of tools allows for thetransfer of a rough cut stone texture to tread edges, corners andrisers of cast in place steps. They can also be effectively used forcountertops, pool coping and wall caps.

Clear Guard® Cure & SealClear Guard® Cure & Seal is a solvent-based,VOC compliant, non-yellowing, curing andsealing compound for newly poured andexisting concrete surfaces. The product isformulated for curing and sealing uncoloredconcrete, integrally colored concrete and colorhardened concrete, stamped or stenciled con-crete and cementitious overlays. Clear Guard®

Cure & Seal visually enhances the concretecolor, protects the surface from dirt and stainingand minimizes the affects of deicing salts andexposure to gas or oil.

EEnnggiinneeeerreedd CCoonnccrreettee PPeerrffoorrmmaannccee

Elements™ Transparent Concrete StainElements™ Transparent Concrete Stainrepresents the latest in nanopigmenttechnology. It is formulated to readilypermeate the concrete surface andcreate translucent color variationssimilar to reactive acid stain. It is apenetrating, non-film forming stainfor existing concrete surfaces. It isresistant to fading from sunlight. Itcan be used on interior concretefloors and exterior concrete hardscapes.It may also be applied to concrete blocks,pavers and cementitious overlays.

2084

-30-

10

51

CHEMICALS

Form Release Agents and Treatments

Curing Compounds and Liquid Hardeners

Curing and Sealing Compounds

Maximum PlusA light, clean, odorless, chemically-reactive architectural form release agent. VOC compliant and formulated for use with a wide variety of forming materials.Coverage: 1200 to 2500 sq. ft. per gallon.

UnikoteForm Release

A general purpose, neutral barrier form release agent. VOC compliant and formulated tobe non-staining. Safe to use with secondary toppings or coatings, caulks and sealants.Coverage: 750 to 1750 sq. ft. per gallon.

Unikote Form Oil An economical, general use form oil. Economical cost basis and VOC compliant.Coverage: 1000 to 2000 sq. ft. per gallon.

UniWhiteCure WaxF

High performance, water-based, white pigmented wax curing compound. VOC compliant. ASTM C309, Type II, Class A, AASHTO M148.Coverage: 200 sq. ft. per gallon.

UniWhiteCure Wax DOTF

High solids, white pigmented, wax-based curing compound. VOC compliant. DOT specification for approved states. CRDC-300, ASTM C309, Type II, Class A, AASHTO M148. DOT specifications for approved states available.Coverage: 200 sq. ft. per gallon.

UniClearCure WaxF

High performance, clear, water-based wax curing compound. VOC compliant.ASTM C309, Type I, Class A, AASHTO M148. DOT specification for approved states.Coverage: 200 sq. ft. per gallon.

UniWhiteCure ResinF

Water emulsified, white pigmented, resin curing compound. VOC compliant. ASTM C309,Type II, Class A & B, AASHTO M148. Coverage: 200 sq. ft. per gallon.

UniResinCure WBF

A clear resin based membrane forming dissipating curing compound. ASTM C309 Type I(Type I-D available) Class A & B. Waterbased. DOT formula available.Coverage: 200 sq. ft. per gallon.

Cure HardF

An economical, silicate-based, ready-to-use, curing, hardening and dust proofing compound. VOC compliant. Ideal for preparing floors and / or base slabs to receive a secondary topping, coating or finish. Coverage: 200-500 sq. ft. per gallon.

UniCure & Seal WBF

A water-based clear acrylic curing and sealing compound. Cures, seals, hardens anddust-proofs freshly placed or aged concrete. VOC compliant. ASTM C309, Type 1, 1-D,Class A & B. Coverage: 200-600 sq. ft. per gallon.

UniCure & Seal 25

25% high solids, solvent-based clear acrylic curing and sealing compound. Cures, seals,dustproofs freshly placed concrete. VOC compliant. ASTM C309, Type 1, 1-D, Class A &B. ASTM C1315, Class A. Coverage: 200-600 sq. ft. per gallon.

UniCure & Seal 30

30% high solids, solvent-based clear acrylic curing and sealing compound. Cures, seals,dustproofs freshly placed concrete. VOC compliant. ASTM C309, Type 1, 1-D, Class A &B. ASTM C1315, Class A. Coverage: 200-600 sq. ft. per gallon.

UniCure & Seal 1315

High solids, solvent-based clear acrylic curing and sealing compound. Cures, seals, dustproofs freshly placed concrete. VOC compliant. ASTM C309, Type 1, 1-D, Class A &B. ASTM C1315, Class A. Coverage: 200-600 sq. ft. per gallon.

UniSealA 25% solids, transparent, high gloss sealer and curing compound. 100% acrylic-based,heavy-duty, non-yellowing solvent-based sealer. ASTM C1315, Class A. Interior and exterior applications. Coverage: 200-600 sq. ft. per gallon.

UniSeal TufA premium, transparent, high gloss sealer and curing compound. 100% acrylic-based,heavy-duty, non-yellowing solvent-based sealer. ASTM C1315, Class A. Interior and exterior applications. Ultra tough film. Coverage: 200-600 sq. ft. per gallon.

Concrete and Masonry Sealer

Silane Sealer WBF

A premium, water-based blend of silane and siloxane based waterproofing components.Prevents moisture and salt attack to concrete, masonry, blocks and bricks. VOC compliant.Coverage: 100-200 sq. ft. per gallon depending on application.

2

2084

-31-

10

52

CHEMICALS

Floor Hardeners / Toppings and Levelers

UniShake QuartzNatural

A natural quartz-silica mixture of finely graded aggregates, plasticizers and Portlandcement. Natural concrete gray color. Interior and exterior applications. Increases surfaceabrasion resistance two times over normal concrete mix designs.Coverage: 0.75 - 2.5 lb. per sq. ft.

KreatsealF A colorless, odorless, premium water-based reactive siliconate concrete sealer. VOC compliant. 10 and 20 year warranty. Coverage: 200-300 sq. ft. per gallon.

Uniflow Self-leveling, free flowing, cementitious, non-structural floor underlayment. All substratesmust be primed with Universal’s Uniprimer. Coverage: 24.4 sq. ft./bag at 1/4".

Microment FFSingle-component, cement-based, multipurpose, trowel-grade dressing, patch, underlayment and embossing agent. Micro-thin, skim coating repair product. Interior use.Coverage: for repairs: 3-5 sq. ft. per 1 lb. over 1/16", for surface skimming: 10-30 sq. ft.per 1 lb. depending on surface applied.

Cement Repair Mortars

UniPatch 5 Fast-setting, single-component, polymer modified, cement-based, trowel grade repair mortar. Vertical and horizontal applications.

UniPatch 20 Single-component, polymer modified, cement-based, trowel grade repair mortar.Vertical and horizontal applications.

UniRoad Repair DOT

Single-component, very rapid setting, chemical action, concrete repair mortar for highwayand heavy industrial repair jobs. Fast track and deep repairs. ASTM C928.

UniPatch VO Single-component, Portland cement-based, polymer modified, “non-sag” repair mortar forvertical and overhead applications.

UniPlugUniPlug Fast

Quick setting, high early strength generating, hydraulic cement for patching and repairingactive water leaks. Super fast-setting formula, UniPlug Fast available upon request.

Latex Bonding Agents

Epoxy Construction Adhesives

Non-Shrink Grouts

UniBondF

Water-based, bonding agent and admixture for cement mortars and cement-based repairmortars. Acrylic emulsion chemistry. Non-emulsifiable. VOC compliant.Coverage: 200-300 sq. ft. per gallon depending on application.

ProweldF

Water-based, bonding agent and admixture for cement mortars and cement-based repairmortars. PVA emulsion chemistry. Reemulsifiable. VOC compliant.Coverage: 200-400 sq. ft. per gallon depending on application.

UniBond LVFH100% solids, hi-mod, low viscosity, moisture insensitive, structural epoxy adhesive.Bonding, grouting and anchoring. ASTM C881-91, Type I, II, IV, V, Grade 1, Class C.VOC compliant.

UniBond MVFH100% solids, hi-mod, medium viscosity, moisture insensitive, structural epoxy adhesive.Bonding, grouting and anchoring. Mix with sand to produce mortar. ASTM C881-91, Type I, II, IV, V, Grade 2, Class C. VOC compliant.

UniBond RapidGel PasteFH

100% solids, hi-mod, gel-paste viscosity, moisture insensitive, structural epoxy adhesive.Rapid setting, horizontal anchoring of dowel bars. Bonding, grouting and anchoring. ASTMC881-91, Type I, II, IV, V, Grade 3, Class C. VOC compliant.

UniBinderFH

100% solids, lo-mod, low viscosity, moisture insensitive, structural epoxy adhesive.Bonding, grouting and anchoring. ASTM C881-91, Type I, II, IV, Grade 1, Class C.VOC compliant.

UniGroutNon-shrink, natural-aggregate, construction-grade grout. CRD C621 and ASTM C1107.Approximate Yield: .43 cu. ft. per 50 lb. bag.

UniGrout SuperNon-shrink, natural-aggregate, high performance, high precision grout. CRD C621 andASTM C1107. High flow and extended work time.Approximate Yield: .43 cu. ft. per 50 lb. bag.

2084

-14-

10

BAR SUPPORTS

TYPICAL WIRE SIZE & GEOMETRY

MINIMUM WIRE SIZE

TOP LEGS RUNNER

NO. 4 NO. 6 -

NO. 4 NO. 6 NO. 7

UP TO & INCLUDING 2"NO. 7 NO. 7 -

OVER 2" TO 5"NO. 4 NO. 4 -

UP TO & INCLUDING 2"NO. 7 NO. 7 NO. 7

OVER 2" TO 5"NO. 4 NO. 4 NO. 4

NO. 7 NO. 7 -

NO. 6 NO. 6 -

OVER 2" TO 5"NO. 4 NO. 4 -

OVER 5" TO 9"NO. 2 NO. 2 -

OVER 9"NO. 0 NO. 0 -

SAME AS HC -

NO. 2 SAME AS HC -

SAME AS CHC NO. 4

UP TO & INCLUDING 2"NO. 4 NO. 4 -NO. 2 NO. 2 -

OVER 2" TO 5"NO. 2 NO. 4 -

USUAL GEOMETRY(VARIATIONS OF PLUS OR MINUS 1/8")

3/4" TO 3" HEIGHTS IN 5-FOOT AND10-FOOT LENGTHS.

LEGS SPACED 5" ON CENTER, VERTICAL

SAME AS SB

3/4" TO 5" HEIGHTS IN INCREMENTS OF1/4" AND LENGTHS OF 5 FEET.

LEGS SPACED 2-1/2" ON CENTER.

SAME AS BB

3/4", 1", 1-1/4", 1-1/2" AND 1-3/4" HEIGHTS.

3/4", 1" AND 1-1/2" HEIGHTS.4", 5" AND 6" WIDTHS.

LEGS AT 20 DEGREES OR LESS WITHVERTICAL. WHEN HEIGHT EXCEEDS 12",LEGS ARE REINFORCED WITH WELDED

WIRES OR ENCIRCLING WIRES.HEIGHTS IN 1/4" INCREMENTS.

SAME AS HC. THE LONGEST LEG WILLGOVERN THE SIZE OF WIRE TO BE USED.

HEIGHTS IN INCREMENTS OF 1/4".

SAME AS HC IN 5-FOOT AND 10-FOOTLENGTHS. ALL LEGS ARE 8-1/4" ON

CENTER MAXIMUM, WITH LEGWITHIN 4" OF END OF CHAIR.

SAME AS CHC

UP TO 5" HEIGHTS IN INCREMENTS OF 1/4".WITH NO. 4 TOP WIRE, MAXIMUM

LEG SPACING IS 5" ON CENTER.WITH NO. 2 TOP WIRE, MAXIMUMLEG SPACING IS 10" ON CENTER.

SYMBOL

SB

SBU

BB

BBU

BC

JC

HC

HCM

CHC

CHCU

CHCM

BAR SUPPORT ILLUSTRATION

SLAB BOLSTER

SLAB BOLSTER UPPER

BEAM BOLSTER

BEAM BOLSTER UPPER

BAR CHAIR

JOIST CHAIR

HIGH CHAIR

HIGH CHAIR FOR METAL DECK

CONTINUOUS HIGH CHAIR

CONTINUOUS HIGH CHAIR UPPER

CONTINUOUS HIGH CHAIR FOR METAL DECK

ASK ABOUT OUR FULL LINE OF PLASTIC BAR SUPPORTS AND ACCESSORIES.

2

53

2084

-13-

10

BRIDGE HANGERS

BRIDGE DECK HANGERSType Part # Style SWL (lbs.)1 T1H 90 & 90 deg. 3,5001-A T1AH 90 & 45 deg. 3,5002 T2H 90 & 90 deg. 2,375

1" haunch2-A T2AH 90 & 45 deg. 2,5003 T3H 90 & 90 deg. 2,500

2-1/2" haunch4 T4H 90 & 90 deg. 6,0004-A T4AH 90 & 45 deg. 6,0001-1A CHT11A Comb. hangers 3,5001-4A CHT14A Comb. hangers 6,0007 T7H 90 & 90 deg. 2,375

1-1/2" haunch7-A T7AH 90 & 45 deg. 2,375

1-1/2" haunch8 T8H 15 & 15 deg. 3,0008-A T8AH 15 & 45 deg. 3,000

BRIDGE DECK HALF HANGERSType Style Part Strut Tail SWL

# Dia. Length (lbs.)

1-C 90 deg. BDHH1C 0.375 9" 3,0001-S 90 deg. BDHH1S 0.375 6" 3,0001-AC 45 deg. BDHH1AC 0.375 12" 3,0001-AS 45 deg. BDHH1AS 0.375 6" 3,0004-AC 45 deg. BDHH4AC 0.440 12" 6,0004-AS 45 deg. BDHH4AS 0.440 6" 6,0004-C 90 deg. BDH4C 0.440 9" 6,0004-S 90 deg. BDH4S 0.440 6" 6,0002-C 1" haun. BDH2C 0.375 9" 2,3752-S 1" haun. BDH2S 0.375 6" 2,3757-S 2½" haun. BDH7S 0.375 6" 2,3758-C 15 deg. BDH8C 0.375 9" 2,3758-S 15 deg. BDH8S 0.375 6" 2,3754-AP 45 deg. PSHH4APR 0.440 6"x4"x2" 3,3004-AP-P 45 deg. PSHH4APRP 0.440 6"x4"x2" 3,300

with plateOne 1/2" coil nut included with each hanger.Flange Width (in.): 8, 9, 10, 11, 12, 13, 14, 15,

16, 17, 18, 19, 20, 21 & 22. (Add width to Part #)

1/2" hex coil nuts provided with each hanger.Designed for use with 1/2" diameter bolts only.

Type Part # SWL (lbs.)BDH-1 TBDH1 4,500BDH-2 TBDH2 4,500BDH-3 TBDH3 4,500

Size (in.): 24, 25, 26, 27, 28, 29, 30, 31, 32, 33, 34,35, 36, 37, 38, 39, 40, 41, 42, 43, 44, 45, 46, 47,48, 49, 50, 51, 52, 53 and 54. (Add size to Part #)

FILLET HANGERLength: 22" Part #FH

FILLET CLIPSize: 3/4" thru 4" Part #FCCoil nut and bolt not included.

HOOK HANGERSType Part # Style SWL (lbs.)1-B T1BH 90 deg. 3,5001-AB T1AB 45 deg. 3,5002-B T2B 90 deg. 2,3754-AB T4AB 45 deg. 5,000

Flange Width (in.): 8, 9, 10, 11, 12, 13, 14, 15,16, 17, 18, 19, 20, 21 & 22. (Add width to Part #)1/2" hex coil nuts provided with each hanger.

OVERHANG BRACKETSSTANDARD OVERHANG BRACKET

PART #SOHBOverhang Bracket Conversion Kit converts standardoverhang bracket to adjustable overhang bracketusing contractor owned horizontal member.

Standard Kit Part #SOBSHeavy Duty Kit Part #SOBHD

ADJUSTABLE OVERHANG BRACKETPart #BOBPart #BOBD

HEAVY-DUTY ADJUSTABLE OVERHANG BRACKETPart #BOBHD

GUARD RAIL RECEPTACLESize: 2 x 4 Part #BOBGRR24Size: 2 x 6 Part #BOBGRR26

Includes 2 ea. 1/2" N.C. bolts with nuts.

BRIDGE OVERHANG BRACKET EXTENDER

Part #BOBEXTIncludes 2 ea. 1/2 N.C. bolts with nuts.

WALL PLATE ASSEMBLYAssembly Part #WPABOBAdjustment Plate Part #APWall Bracket Part #WPAWB

For adjustment bridge overhang bracket.For use with 3/4" diameter bolt.

WIRE BEAM SADDLE HANGERSLight forming up to 7½" slab thickness (1½:1) safety factor.Heavy forming over 7½ slab thickness (2:1) safety factor.Safe working loads (SWL) are for complete hangerType 1 and 2 may be obtained with safe work-ing loads of 2,500 lbs. (#8 Wire), 4,000 lbs. (#6Wire) and 6,000 lbs. (#4 Wire).

Wire Part # Part # Part # Part ##8 WBST18 WBST28#6 WBST16 WBST26#4 WBST14 WBST24 WBST34 WBST454

All (2:1) light forming and (2:1) heavy forming:1,875 lbs. (#8 Wire), 3,000 lbs. (#6 Wire) and 4,500 lbs.(#4 Wire).Type 3SWL (2:1) light forming = 3,000 lbs.SWL (2:1) heavy forming = 2,250 lbs.Type 4 and 5SWL (2:1) light forming = 1,000 lbs.SWL (2:1) heavy forming = 750 lbs.

PLATE SADDLE HANGER7-Ga. Wire (1000#) and 4 Ga. Wire (1500#)Size: Overall length to 18" (with 1¾" plate)

Longer sizes available3¾" plate availablePlates can be different sizesPlates can be set-back

SNAP TIE HANGERSType ISWL (2:1) = 1,500 lbs.Type IISWL (2:1) = 2,000 lbs.Overall dimensions measured from inside toinside of heads.

Type Description Part#I Standard STHT1II Heavy Duty STHT2

Overall dimensions (in.): Up to 30, 33, 36, 39, 42,45, 48, 51, 54, 57 and 60.Available with 1" large plastic cones or washers.

COIL HANGERSCOIL HANGER SADDLE TYPE

Diameter SWL (lbs.)1/2" 2,2503/4" 5,6251" 7,500

Overall Length Part #To 24" CH24To 30" CH30To 36" CH36To 42" CH42To 48 CH48

Overall length is total length of hanger frombottom of coil to bottom of coil.

ADJUSTABLE HALF HANGER

1 90 deg. Part #T1AHH1-A 45 deg. Part #T1AHH2 90 deg./1" haun. Part #T2AHH8 15 deg. Part #T2AHH

One clip and three nuts included.

HOOK DETAIL

BROACHED DECK HANGERS

54

531-

34-1

0

SNAPTIES

Meadow Burke can provide a full range of sizes and types of integral head snapties to suit your specific job needs. Availablein both plastic cone and metal washer designs, these ties can be provided from stock for common end and wall dimensions,or can be produced quickly for your special wall forming dimensions.

Over the years, the plastic cone design has proven to be the preferred spreader device over the metal washer design.Fabricated from high impact polystyrene material, the plastic cone provides positive spreader action, while at the same timecovering the breakback portion of the wire tie to insure that it will not adhere to the concrete, and will break back and removefrom the concrete easily. Plastic cones also provide a more desirable cone shaped cavity in the wall, which is better suited topatching or grouting.

1" x 1" Plastic Cone

Wall Thickness

Metal Washer

Breakback Breakback

Wall Thickness

®


RHWRCH EndEndEndEnd

STANDARD BREAKBACK IS 1". 1/2" AVAILABLE ON SPECIAL ORDER (RHW orders only).Stock ties sold in boxes of 100 only.RHW - round head with washer spreader.RHC - round head with cone spreader.For improved performance and guaranteed breakback results, specify plastic cones when ordering any snapties.Meadow Burke Products cannot guarantee breakback results when metal washers and wax coatings are specified.

SNAPTIE - STANDARD2,250 LBS. SWL

4-3/4" END (Lumber and Wedge) 8-1/4" END (Lumber and Wedge)

6" 311207 311210 23.57" 311401 311414 24.7

7-5/8" 311508 311511 25.48" 311605 311618 25.89" 311809 311812 26.910" 312002 312015 28.0

11-5/8" 312303 312316 29.912" 312400 312413 29.914" 312808 312811 32.615" 313001 313014 33.716" 313205 313218 34.818" 313603 313616 37.120" 314000 314013 39.324" 314806 314819 43.830" 316008 316011 50.636" 317201 317214 57.4

Product Product WeightWall Size Code Code Per 100

RHW RHC (LBS)

Product Product WeightWall Size Code Code Per 100

RHW RHC (LBS)

6" 321200 321213 31.87" 321404 321417 32.9

7-5/8" 321501 321514 33.68" 321608 321611 34.09" 321802 321815 35.110" 322005 322018 36.3

11-5/8" 322306 322319 38.112" 322403 322416 38.514" 322801 322814 40.815" 323004 323017 41.916" 323208 323211 43.018" 323606 323619 45.320" 324003 324016 47.624" 324809 324812 52.130" 326001 326014 50.636" 327204 327217 59.3

STEEL WEDGE MB Item Number 400163Weight per 100 40 lbs.Safe working load 3,250 lbs.For standard or heavy snapties.

2

55

MB WeightSize Item Per 100

Number (lbs.)

6” 300406 268” 300408 30

10” 300410 3512” 300412 3914” 300414 4316” 300416 4818” 300418 5220” 300420 5724” 300424 6530” 300430 7936” 300436 92


Number (lbs.)

2” x 4” 270746 122” x 6” 270759 14


Number (lbs.)

6” 292598 258” 292600 27

10” 292602 2912” 292604 32

531-

35-1

0

LIGHT FORMING

PANEL TIE - STANDARDPANEL TIE - HEAVY


®

Panel TiesWall Size Standard Heavy

MB Item Weight MB Item Wt./100Number (lbs.) Number (lbs.)

6" 330013 17.5 380018 20.37" 330026 18.6 380021 21.68" 330039 19.7 380034 22.99" 330042 20.9 380047 24.210" 330055 22.0 380050 25.512" 330071 24.2 380076 28.214" 330097 26.6 380092 30.915" 330107 27.7 380102 32.016" 330110 28.9 380115 33.518" 330136 31.1 380131 36.120" 330152 33.5 380157 38.724" 330194 38.0 380199 43.9

STANDARDSafe Working Load = 2,250 lbs.Approximate Safety Factor = 2:1

HEAVYSafe Working Load = 3,000 lbs.Approximate Safety Factor = 2:1

FLAT TIE - STANDARD

BASE TIE

WALER TIE

STRONGBACK TIE MB WeightSize Item Per 100

Number (lbs.)

4" x 4" 270720 164" x 6" 270733 186" x 6" 270734 20

(Symons - Mod-U-Form)Standard breakback is 1/4".2,250 lbs. safe working load, approx. 2:1 safety factor.For other wall sizes - P.O.A.

1-5/32" 1-5/32"Wall Thickness

56

531-

36-1

0

LIGHT FORMINGinnovating concrete construction

®

MB Item Description Type WeightNumber Bolt Dia. Size Per 100

470009 1/2" 3" x 4" x 1/4" Standard 83470106 1/2" 4" x 5" x 1/4" Heavy 143470012 3/4" 3" x 4" x 1/4" Heavy 85470119 3/4" 4" x 6" x 1/4" Standard 141470151 3/4" 5" x 5" x 1/2" Heavy 347470178 1" 5" x 5" x 1/2" Standard 341470180 1" 7" x 7" x 3/4" Heavy 1,150470182 1-1/4" 6" x 6" x 1/2" Standard 330470184 1-1/4" 7" x 7" x 3/4" Heavy 1,150470187 1-1/2" 5" x 5" x 3/4" Standard 544470188 1-1/2" 7" x 7" x 3/4" Heavy 1,140

FORM BRACE ALIGNERMB WeightItem Per 100

Number (lbs.)

400503 8

WEDGE BOLT

PENCIL ROD TIGHTENER

PENCIL ROD (1/4") COILS OR STRAIGHT

FORM CLAMP

Packaging MB WeightUnits/ Item Per 100Bucket Number (lbs.)

500 270050 12

MB WeightSize Item Each

Number (lbs.)

#1 - 1/4" Rod 201016 1.5

#2 - 3/8" Rod 201029 2.7#3 - 1/2" Rod 201032 2.7

MB PackagingItem (LF/lbs.)

Number

400008 600 LF / 100

MB WeightSize Item Per 100 Package

Number (lbs.) Quantity

#1 - 1/4" Rod 600015 65 50#2 - 3/8" Rod 600031 125 25#3 - 1/2" Rod 600057 188 25

FLAT WASHER

Straightening and cutting available per 100 lbs.Available in 20' lengths.

For use with coil bolts and coil rod/nut(s).Washer sizes are designed to provide adequate bearing againstwood form members.

57

2

531-

37-1

0

MEDIUM/HEAVYFORMING innovating concrete construction

®

MB WeightItem Description Safe Work Per 100

Number Bolt Dia. Packaging Loads (lbs.) (lbs.)

207188 1/2" 1,000 4,500 6207191 3/4" 500 9,000 19207201 1" 150 18,000 41207214 1-1/4" 70 27,000 76207227 1-1/2" 50 40,000 119

COIL TIE - TWO STRUT

COIL NUT - STANDARD

Safety factors are 2:1.NOTE: Epoxy coating of coil ties may reduce inside

thread diameter.

1/2" 4.5M 1/2" 6.75M 3/4" 6.75M 3/4" 9M 1" 13.5MLength Weight Weight Weight Weight Weight

(lbs.) (lbs.) (lbs.) (lbs.) (lbs.)

to 8" 32 51 69 91 155over 8" to 9" 34 55 73 97 164

over 9" to 10" 36 59 77 103 173over 10" to 11" 39 63 81 110 182over 11" to 12" 42 67 85 116 191over 12" to 13" 44 71 89 122 200over 13" to 14" 47 75 93 128 209over 14" to 15" 49 80 98 135 218over 15" to 16" 51 84 102 141 227over 16" to 17" 54 88 106 147 236over 17" to 18" 56 92 110 153 245over 18" to 19" 58 96 114 160 254over 19" to 20" 60 100 118 166 263over 20" to 21" 63 105 123 172 272over 21" to 22" 65 109 127 178 281over 22" to 23" 67 113 131 185 290over 23" to 24" 70 117 135 191 299

Each 1" over 24 add 2 4 4 6 9Add for Cone-Fast 4 7 12 4 22Add for Water Seal 1 1 1 1 1

*2001 Welding Coil Tie Deduct 7 8 17 20 41

Weights per 100 pieces.

CONE FAST CONES MB WeightItem Description Per 100

Number Bolt Dia. Setback (lbs.)

205151 1/2" 1" 3.3205177 1/2" 1-1/2" 4.4205180 1/2" 2" 5.6205232 3/4" 1" 5.4205203 3/4" 2" 14.0205216 1" 2" 17.1205229 1-1/4" 2" 18.5

Screw-on plastic cone.

58

531-

38-1

0

FORMING ANDBRIDGE DECK HANGERSinnovating concrete construction

®

HANGER FRAME - STANDARD

CONTINUOUS COIL RODLOW-STRENGTHHI-STRENGTH

Low-Strength - 10 Ft. Hi-Strength - 12 Ft. WeightNominal MB Item Safe Work MB Item Safe Work PerDiameter Number Load (lbs.) Number Load (lbs.) 100 LF

1/2" 400201 9,000 400200 9,000 535/8" 400202 400203 12,000 853/4" 400204 12,000 400208 18,000 1201" 400212 24,000 400213 38,000 212

1-1/4" 207120 36,000 400221 55,000 3351-1/2" 207122 54,000 400224 68,000 601

SCREED HOLDER - HEAVY-DUTY MB WeightItem Type Length Per 100

Number (lbs.)

402350 No. 4 4-1/2" 162402351 No. 5 6-3/4" 246402352 No. 6 9-3/4" 299207201 Extra Coil Nuts 1" Dia. 41

Minimum coil penetration same as shown for coil bolts.Two (2) standard coil nuts or one (1) heavy coil nut must be used to develop the safe working load.Meadow Burke Products will not guarantee the safe working load of any high strength coil rod which has been field welded or bent.1/2" coil rod available only in high tensile material in either 10-foot or 12-foot lengths.1-1/4" not available in 10-foot lengths.

HANGER FRAME - HEAVY

Flange Width Wt. (lbs.)

Up to 10" 113Over 10" to 12" 119Over 12" to 14" 125Over 14" to 16" 131Over 16" to 18" 138Over 18" to 20" 144Over 20" to 22" 150Over 22" to 24" 158

Each 1" Over 24" Add 3.1

SWL - 3,000 lbs. SWL - 3,000 lbs.

SWL - 5,000 lbs.SWL - 5,000 lbs.

15º 15º

15º 15º

All above include two (2) 1/2" coil nuts per hanger.

All above include two (2) 1/2" coil nuts per hanger.

Flange Width Wt. (lbs.)

Up to 10" 113Over 10" to 12" 119Over 12" to 14" 125Over 14" to 16" 131Over 16" to 18" 138Over 18" to 20" 144Over 20" to 22" 150Over 22" to 24" 158

Each 1" Over 24" Add 3.1

Coil Nut Included. Specify type and O.D. of pipe.

59

2

531-

39-1

0

BRIDGE DECKHANGERSinnovating concrete construction

®

HALF HANGER - C FOR CONCRETE BEAM

HALF HANGER - STRAIGHT TAIL

MB WeightItem Angle Safe Work Wire (C) Per 100

Number Load (lbs.) Diameter Dimension (lbs.)

492470 90º 3,500 0.375 9" 43492476 45º 4,500 0.375 9" 50492480 15º 4,000 0.375 9" 58

HALF HANGER - S FOR STEEL BEAM

492470

492480

492476

One 1/2" hex coil nut included with each hanger.

492500

492498

492497

492495

492492

492490

492485



492485 90º 3,500 0.375 9" 50492490 45º 3,500 0.375 12" 71492492 45º 5,000 0.440 12" 85492495 15º 3,500 0.375 9" 69492497 15º 4.000 0.440 9" 80492498 1" HH-90º 2,375 0.375 9" 55492500 1-1/2" HH-90º 2,000 0.375 9" 60



492501 90º 3,500 0.375 6" 40492502 45º 4,000 0.375 6" 54492506 45º 6,000 0.440 6" 62492503 15º 3,500 0.375 6" 60492507 15º 5.000 0.440 6" 68492504 1" HH-90º 2,375 0.375 6" 46492505 1-1/2" HH-90º 2,000 0.375 6" 51

492503

492506

492502

492501

492505

492504

492507



(C)

(C)

(C)

(C)

(C)

60

531-

40-1

0

MEDIUM/HEAVYFORMING innovating concrete construction

®

COIL BOLT

Bolt MB Item MB Item MB Item MB Item MB ItemLength Number Number Number Number Number1-1/2" 290995

2" 470203 470216 2913382-1/2" 470205 470218 291339

3" 470300 470313 4704223-1/2" 291026 291233

4" 470407 470410 470423 470436 4704395" 470504 470517 4705206" 470601 470614 470627 470630 4706437" 470708 470711 2913728" 470805 470807 470821 4708349" 470902 470915 470928

10" 471008 471011 471023 47103711" 471105 47111812" 471202 471215 471228 471231

ADJUSTABLE COIL BOLT

Bolts may be furnished with standard formed head or made with continuouscoil rod and hex nut welded on.

Min. Coil Penetration (see chart below)

1/2" Diameter 3/4" Diameter 1" Diameter 1-1/4" Diameter 1-1/2" Diameter

Safe Work Load Safe Work Load Safe Work Load Safe Work Load Safe Work Load4,500 / 6,750 lbs. 9,000 lbs. 18,000 lbs. 27,000 lbs. 40,000 lbs.

Min. Coil Penetration Min.Coil Penetration Min.Coil Penetration Min.Coil Penetration Min.Coil Penetration

Length

MB Description WeightItem Per 100

Number Diameter Length (lbs.)

473006 1/2" 12" 69473019 1/2" 18" 96473022 1/2" 24" 122473035 3/4" 12" 170473048 3/4" 18" 230473051 3/4" 24" 290

OVERHANG BRACKET - SUPER 96Lightweight: Easier handling, less labor, reduced

equipment demand.

High Strength: Design handles up to 10 kip in “best” condition.

Gang Ability: Gangs up to 24' - 0".

Full Engineering Services: Layout services with load and spacing design.

Quick, Easy Adjustment: Fully adjustable from the bridge deck.

Adjustable Handrail: Accommodates sloping or super-elevated overhangs.

Length: 96 inches.

61

2

531-

41-1

0

BRIDGE DECKOVERHANG PRODUCTSinnovating concrete construction

®

OVERHANG BRACKETOVERHANG BRACKET - LONG

OVERHANG GUARD RAIL ADAPTERBOLT ON / SLIP ON

Meadow Burke Products bridge overhang bracket safe work load depends on loading,spacing and the bridge overhang bracket geometry. Consult with Meadow Burkeengineers for specific design conditions and working loads along with the informationpublished in the bridge deck forming handbook.

OVERHANG EXTENDER

MB WeightItem Type each

Number (lbs.)

400258 4250 45400262 4260 50

4250 configuration accommodates vertical height adjustment of 30º to 50º.4260 configuration accommodates vertical height adjustment of 50º to 70º.

LONG CONVERSION KITOne long diagonal and vertical leg.

MB WeightItem each

Number (lbs.)

400259 10

OVERHANG WALL PLATE ASSEMBLY


Number (lbs.)

400265 4275 (2 x 4) 3.4400267 4280 (2 x 6) 4.4


Number (lbs.)

400263 4270 1.75400270 Adjustment Plate 0.41400271 Wall Bracket 1.34


Number (lbs.)

400269 4285 3.6

Includes two 1/2" x 1" bolts with nuts (UNC) for bolting to 4250 bridge overhangbracket.

4275 includes two 1/2" x 1" bolt with nuts (UNC) for attachment to bracket or extender.

For use with 3/4" diameter bolt.Wall Bracket

Adjustment Plate

4280Slip on Receptacle

Accepts 2 x 6

4275Bolt on Receptacle

Accepts 2 x 4

Lower VerticalLeg

LowerDiagonal Leg

UpperDiagonal Leg

Slide AssemblyBolt Holder Assy.

Upper Vertical Leg

54"

62

91

Skid LoadersTrack Loaders

Telescopic HandlersExcavators

Chippers & Stump GrindersPaving Equipment

AugersBuckets

GrapplesBackhoes & Trenchers

Landclearing AttachmentsHydraulic Compactors

Compaction EquipmentAsphalt & Trench Rollers

TampersMulchers

Straw BlowersHydroseeders

Construction LasersLevel-Transits

Skid Steer & Forklift Attachments

Excavating & Landscaping 4

David White

684-

13-1

0

SKID LOADERS

Models 4640E / 5240E / 5640E / 6640E / 7810E

• Narrow Widths –Model 4640E has a width of only 59.7" with optional wheel package to easily fit on sidewalks.

• Joystick Control option – Now an available option on models 4640E Turbo, 5240E, 5640E Turbo and 6640E

• Innovative acoustical materials – Newly-designed engine-related components to reduce sound levels, inside and out

• New higher operating load capacities – up to 2900 lbs. with optional counterweights

• Advanced high horsepower engines – with in-cylinder glow plugs to improve cold weather starting, and an auto-shutdown system

• Exceptional hydraulic power – for high breakout forces and outstanding attachment performance

Models 3640E / 4240E

• Compact, low-profile design – for maneuverability in narrow, low-clearance areas

• Powerful Yanmar diesel engines – for power and performance where it counts

• All-Tach® attachment mounting system – compatible with most attachments.

SERIES SKID LOADERS

92

684-

8-10

SKID LOADERS

E-SERIES SKID LOADERS

*Narrow width with new offset tire option.

All dimensions are in inches (millimeters) unless otherwise noted.

SPECIFICATIONS3640E 4240E 4640E 5240E 5640E 6640E 7810E

Overall Operating Height (fully raised) A 139.6 (3546) 141.1 (3584) 149 (3785) 154.2 (3917) 162 (4115) 168.3 (4113) 187.8" (4770)Height to Hinge Pin (fully raised) B 108.1 (2746) 110 (2794) 115.5 (2934) 120.7 (3066) 123 (3124) 124.3 (3157) 142" (3607)Overall Height w/ ROPS/FOPS Cab C 70.3 (1786) 71.9 (1826) 78.0 (1981) 78.0 (1981) 81.0 (2057) 82.0 (2082) 81.0" (2057)Ground Clearance D 6 (152) 8.3 (211) 7.5 (191) 7.5 (191) 8.0 (203) 9.1 (231) 9.1 (231)Overall Length E 114 (2896) 116.2 (2952) 122.8 (3119) 126.3 (3208) 131.0 (3327) 141.5 (3594) 161.0" (4089)

(w/55" bucket) (w/61" bucket) (w/66" bucket) (w/66" bucket) (w/70" bucket) (w/74" bucket) (w/84" bucket)Overall Length (less bucket) F 88.9 (2258) 91.1 (2314) 89.8 (2281) 94.2 (2393) 99.5 (2527) 105.8 (2687) 122.0" (3099) Wheelbase G 34.5 (876) 36.7 (932) 37.5 (953) 42 (1067) 42.5 (1080) 48.4 (1219) 55.0" (1397)Dump Reach (at full height) H 22.8 (579) 22.6 (574) 27.6 (701) 27.6 (701) 32.8 (833) 35.2 (894) 38.2" (970)Rollback at Ground I 29° 29° 27º 27º 28º 28º 28.5ºDump Angle J 42° 42° 40º 40º 37º 37º 38ºOverall Width K 48.4 (1229) 53/59 (1334/1483) 59.7*/62 (1516*/1575) 62/59.7 (1575/1516) 69 (1753) 72.5 (1841) 81.0" (2057)Bucket Width L 55.3 (1404) 60.6 (1539) 61.5-70 (1562-1778) 66-75 (1679-1905) 70-90 (1778-2286) 74-90 (1880-2286) 84" (2134)Clearance Circle (Rear) M 54.1 (1374) 58.4 (1484) 59.5 (1513) 61.5 (1562) 66.0 (1679) 69.0 (1753) 80.5" (2045)Clearance Circle (Front, less bucket) N 44.1 (1120) 43.4 (1102) 47 (1194) 48 (1219) 50.5 (1283) 54.0 (1372) 60.6" (1539)Clearance Circle (Front, w/bucket) O 69.4 (1763) 69.2 (1758) 74.5 (1892) 79.2 (2012) 82.0 (2083) 90.5 (2299) 101.7" (2583)Seat to Ground Height P 32.6 (828) 33.6 (853) 37.5 (953) 37.5 (953) 42.0 (1067) 43.3 (1100) 41.0" (1041)Rollback at Full Height Q 99° 99° 86º 86º 97º 97º 85ºDump Height R 84.5 (2146) 86.5 (2197) 89.5 (2273) 90.6 (2301) 93.5 (2375) 94.8 (2408) 107.0" (2718)Departure Angle S 26° 29° 25º 25º 26º 29º 21ºStandard Tire Size 27 x 8.5 x 15 HD 10.00 x 16.5 HD 10.00 x 16.5 HD 10.00 x 16.5 HD 12.00 x 16.5 HD 14.00 x 17.5 HD 14.00 x 17.5 HDENGINEMake Yanmar Yanmar Deutz Deutz Yanmar Yanmar CumminsModel 3TNV88 4TNV88 TD2009 TD2009 4TNV98T 4TNV98T B4.5T-99CNet Power (kW) @ RPM 35 hp (26) @2800 46 hp (34) @2800 62 hp (46) @2600 62 hp (46) @2600 84 hp (62.6) @2500 84 hp (62.6) @2500 99 hp (73.8) @2200Displacement (L) 100 cu. in. (1.64) 133 cu. in. (2.19) 140 cu. in. (2.3) 140 cu. in. (2.3) 202 cu. in. (3.3) 202 cu. in. (3.3) 275 cu. in. (4.5)HYDRAULIC SYSTEMAuxiliary Hyd. (L/min) 14.5 gpm (55) 16.5 gpm (62) 19 gpm (72) 19 gpm (72) 21.8 gpm (82.3) 21.8 gpm (82.3) 29 gpm (110)High-Flow Hyd.(L/min) – option N/A N/A 30 gpm (114) 30 gpm (114) 36.9 gpm (139.6) 36.9 gpm (139.6) 41 gpm (155)Filtration 4 micron 4 micron 4 micron 4 micron 4 micron 4 micron 3 micronReservoir Capacity 8 gal. (30.3) 8 gal. (30.3) 12 gal. (45) 12 gal. (45) 16 gal. (60) 16 gal. (60) 15 gal. (56.8)ELECTRICAL SYSTEMBattery 12-volt 12-volt 12-volt 12-volt 12-volt 12-volt 12-volt

(675 CCA) (675 CCA) (950 CCA) (950 CCA) (950 CCA) (950 CCA) (675 CCA)Starter (kW) 12-volt (2.3) 12-volt (2.3) 12-volt (2.0) 12-volt (3.0) 12-volt (3.0) 12-volt (3.0) 12-volt (2.3)Alternator 40-amp. 40-amp. 80-amp. 90-amp. 90-amp. 90-amp. 40-ampCAPACITIES / WEIGHTSRated Operating Load (kg) 1050 lbs. (476) 1350 lbs. (612) 1650 lbs. (748) 1900 lbs. (862) 2200 lbs. (998) 2600 lbs. (1179) 3850 lbs. (1747)Rated Operating Load 1175 lbs. (533) 1475 lbs. (669) 1800 lbs. (816) 2050 lbs. (930) 2500 lbs. (1134) 2900 lbs. (1315)Tipping Capacity (kg)*** 2100 lbs. (952) 2700 lbs. (1225) 3300 lbs. (1497) 3800 lbs. (1724) 4400 lbs. (1996) 5200 lbs. (2359)Fuel Tank (L) 10.3 gal. (38.9) 12.4 gal. (47) 15 gal. (56) 16 gal. (60) 19 gal. (72) 24 gal. (91) 30.5 gal. (115.4)Travel Speed - w/Joystick (km/h) N/A N/A 7.7 mph (12) 7.7 mph (12) 7.6 mph (12.2) 8.6 mph (13.8)with 2-speed drive opt. (km/h) N/A N/A 12.4 mph (20) 12.4 mph (20) 11.5 mph (18.5) 13.1 mph (21.1) 12.5 mph (20)Travel Speed - w/o Joystick (km/h) N/A N/A 7.7 mph (12) 7.7 mph (12) 8.1 mph (13) 9.2 mph (14.8)max. (km/h) 5.9 mph (9.5) 5.4 mph (8.7) 12.4 mph (20) 12.4 mph (20) 12.3 mph (19.8) 13.9 mph (22.4) 7.5 mph (12)Operating Weight (kg) - approx. 4000 lbs. (1814) 4600 lbs. (2087) 6200 lbs. (2812) 6700 lbs. (2764) 7880 lbs. (3574) 8140 lbs. (3692) 10,520 lbs. (4772)

93

4

684-

9-10

COMPACT TRACK LOADERS

CTL65 / CTL75 / CTL85Compact Track LoadersFeatures and Benefits• High-powered, 4-cylinder, liquid-cooled

and emission-certified diesel engines deliver up to 97 hp for exceptional performance. Two models are turbo-charged.

• Two-speed drive system utilizes high-torque, radial-piston motors with plane-tary final drives to match the application and speed of operations.

• SAHR (spring-applied, hydraulic release)multi-disc wet brakes respond quickly, holding the loader on any grade.

• Exceptional hydraulic power for dependable digging, especially in tough conditions.

• Hydraulic self-leveling lift action keeps loads balanced whenever the lift arm is raised.

• Elevated planetary final drives provide very efficient and durable transfer of power to the tracks.

• Tracks made of high strength rubber and steel reinforcement are designed to perform well on all types of terrain.

• Tracks roll on sealed steel rollers within the carriage and stand up in tough conditions.

• Dedicated undercarriage provides flotation needed for working in wet conditions and balanced traction neededfor excavating.

• Tilt-back ROPS structure quickly reveals internal components for maintenance and service.

• Lift arm can be locked in raised position for safety and improved access to service points.

• Engine cover and rear door protect components and open for easy access to engine, air cleaner and more.

• Rear hydraulic cooling system swings out of the way for excellent rear engine access.

SPECIFICATIONCTL65 CTL75 CTL85

ENGINEMake/Model Yanmar/4TNV98 Yanmar/4TNV98T Kubota/V3800 DI-TAspiration Natural Turbocharged TurbochargedDisplacement (L) /Cylinders 202.5 cu. in. (3.3) /4 202.5 cu. in. (3.3) /4 230 cu. in. (3.8) /4Horsepower (kW) @ rpm 67 hp (49) @ 2500 83 hp (62) @ 2500 92 hp (68.3) @ 2200Max. Torque (Nm) 179 ft.-lbs. (243) 219 ft.-lbs. (297) 240 ft.-lbs. (325)PERFORMANCETipping Capacity - SAE J732 (kg) 4630 lbs. (2100) 5952 lbs. (2700) 7056 lbs. (3200)Rated Operating Load (kg)SAE J818 @ 35% of tipping capacity 1620 lbs. (735) 2083 lbs. (945) 2470 lbs. (120)SAE J818 @ 50% of tipping capacity 2315 lbs. (1050) 2976 lbs. (1350) 3528 lbs. (1600)Breakout Force (kN)

Bucket 6724 lbs. (30.0) 7401 lbs. (32.9) 8669 lbs. (38.5)Lift Arm 6709 lbs. (29.8) 7425 lbs. (33) 8547 lbs. (38.0)

ELECTRICALBattery / CCA 12 volt / 660 12 volt / 660 12 volt / 800Alternator 40 amp 50 amp 80 ampUNDERCARRIAGETraction Pump / Traction Drive Piston / Planetary Piston / Planetary Piston / PlanetaryTraction Braking Hydraulic Hydraulic HydraulicDrawbar Pull (kN) 9,918 lbs. (40.5) 11,067 lbs. (50) 13,766 lbs. (61.2)Roller Type / Track Rollers ea. side Steel / 4 Steel / 4 Steel / 5Track Width 12.6" (320) 18.0" (457) 18.0" (457)Track Contact Length 55" (1389) 59.0" (1496) 63" (1598)Ground Pressure (kg/cm2) 4.9 psi (0.34) 4.3 psi (0.29) 4.5 psi (0.31)Travel Speed (km/h)

Low 0-4.5 mph (0-7.2) 0-4.7 mph (0-7.6) 0-4.8 mph (0-7.8)High 0-6.8 mph (0-10.9) 0-7.2 mph (0-11.6) 0-7.5 mph (0-12.0)

HYDRAULIC SYSTEMOperating Pressure (bar) 2988 psi (206) 2988 psi (206) 2988 psi (206)Auxiliary Hyd. Flow (L/min) 18.4 gpm (68.5) 19.8 gpm (74.9) 23.4 gpm (88.6)Auxiliary Hyd. High-Flow - option (L/min.) N/A 36.3 gpm (137.5) 40 gpm (151.7)CAPACITIESFuel (L) 19.8 gal. (75) 23.8 gal. (90.1) 28.5 gal. (107.9)Hydraulic Reservoirs (L) 10.2 gal (38.6) 12.8 gal. (48.5) 15.9 gal. (60.1)Engine Oil (L) 10.8 qt. (10.2) 10.8 qt. (10.2) 14.0 qt. (13.2)Engine Coolant (L) 17.4 qt. (16.5) 17.4 qt. (16.5) 17.4 qt. (16.5)DIMENSIONS & WEIGHTOperating Weight (kg) - approx. 8014 lbs. (3635) 9700 lbs. (4400) 11,244 lbs. (5090)Max. Lift Height to Bucket Pin (mm) A 119.3" (3030) 122.9" (3120) 126.1" (3203)Dump Height (mm) B 93.3" (2370) 94.8" (2405) 95.7" (2430)Reach @ Max. Lift (mm) C 28.8" (730) 34.4" (874) 38.8" (985)Dump Angle D 37° 38.5° 37°Bucket Roll Back @ Ground Level E 35° 31° 30°Length - w/o bucket (mm) F 109" (2756) 117.3" (2980) 123.5" (3135)Length - w/bucket (mm) G 140" (3543) 147.2" (3740) 156.9" (3985)Ground Clearance (mm) H 12.1" (310) 12.8" (325) 13.5" (345)Angle of Departure I 26 30° 30°Height - to top of ROPS J 84" (2123) 85" (2167) 91.3" (2320)Width -w/o bucket (mm) K 62.2" (1580) 70" (1770) 73.2" (1860)Overall Width - w/bucket (mm) L 70" (1778) 74" (1880) 86" (2134)Rear Clearance Radius (mm) M 61" (1549) 66" (1666) 72" (1816)Front Clearance Radius -w/bucket N 93" (2362) 90" (2294) 106.0" (2692)BUCKETMounting Universal quick-attach Yes Yes YesCapacity - SAE heaped (m3) 15.3cu. ft. (0.44) 17.0 cu. ft. (0.48) 22.0 cu. ft. (0.57)

94

684-

11-1

0

TELESCOPIC HANDLERS

SPECIFICATIONSRS6-34 RS6-42 RS8-42/44

CAPACITIESLift Capacity (kg) 6,000 lbs. (2722) 6,600 lbs. (2944) 8,000 lbs. (3629)Max. Lift Height (m) 34'3" (10.4) 42' (12.8) 42'/44' (12.8/13.4)Capacity at Max. Lift Height (kg) 4,000 lbs. (1814) 6,600 lbs. (29442) 7,000 lbs. (3178)Max. Forward Reach (m) 23'3" (7.0) 28'3" (8.6) 28'3"/30'5' (8.6/9.3)Capacity at Max. Reach (kg) 900 lbs. (408) 1,000 lbs. (454)* 1,000 lbs. (454)*Max. Reach below Grade (mm) 24" (610) 14" (356) 14"/16" (356/406)*with outriggers upENGINEManufacturer John Deere John Deere John DeerePower (kW) Std. 99 hp (74) Std. 99 hp (74) Std. 115 hp (86)

Opt. 115 hp (86)Aspiration Turbo Charged Turbo Charged Turbo ChargedModel 4045T 4045T 4045TRated Speed (rpm) 2500 2500 2500COMPONENTSTransmission Dana 3-Speed Power Shift Dana 3-speed Power Shift Dana 3-speed Power ShiftMax. Travel Speed (km/h) 20.2 mph (32.5) 18.8 mph (30.3) 18.8 mph (30.3)Steering 4-Wheel 4-Wheel 4-Wheel

2-Wheel 2-Wheel 2-WheelCrab Crab Crab

Brakes Internal Wet Disc Internal Wet Disc Internal Wet Disc4-wheel Hydraulic 4-wheel Hydraulic 4-wheel Hydraulic

Parking Brake SAHR (Spring-Applied, SAHR (Spring-Applied, SAHR (Spring-Applied,Hydraulic-Released) Hydraulic-Released) Hydraulic-Released)

Axle Manufacturer Dana Dana DanaHYDRAULIC SYSTEMPump Type Gear Gear GearTotal Capacity (L/min) 29 gpm (110) 40 gpm (151) 40 gpm (151)System Pressure (bar) 3000 psi (207) 3000 psi (207) 3000 psi (207)Hydraulic Tank Capacity (L) 35 gal. (133) 45 gal. (170) 45 gal. (170)GENERAL SPECIFICATIONSApproximate Weight (kg) 15,100 lbs. (6850) 22,000 lbs. (9979) 23,350/23,500 lbs.

(10,591/10,659)Length - Less Forks (m) 16' (4.9) 19'1" (5.8) 19'1"/19'10" (5.8/6.1)Width (m) 7'10" (2.4) 8' (2.4) 8' (2.4)Ground Clearance (mm) 14" (350) 16" (400) 16" (400)Wheelbase (m) 9'2" (2.8) 10' (3) 10' (3)Turning Radius (m) 12'6" (3.8) 13'8" (4.2) 13'8" (4.2)Overall Height (m) 7'10" (2.4) 7'10" (2.4) 7'10" (2.4)Frame Leveling 10° 10° 10°Fuel Capacity (L) 29 gal. (110) 47 gal. (178) 47 gal. (178)SPECIAL FEATURESQuick-Attach Bracket Dynattach std. Dynattach std. Dynattach std.TIRE OPTIONSRS6-34 RS6/815.00 x 19.5/12 PR 13.00 x 24/12 PR15.00 x 19.5/12 PR - Foam-Filled 13.00 x 24/12 PR - Foam-Filled15.00 x 19.5 Solid Rubber 13.00 x 24/12 PR - Rock

13.00 x 24 Solid Rubber

RS SeriesTelescopic HandlersThe Gehl RS Series Telescopic Handlers havemore lift height than ever before. . . up to 44'on the RS8. A true “4-story machine.” Allmachines offer excellent visibility, superior loadcapacity, tight turning radius plus a great returnon your investment.

They feature:• Extended lift heights on the RS6 and RS8,

ranging from 42 to 44 feet, making them true“4-story machines.”

• Redesigned ROPS canopy and enclosed cabfor easy operator access to controls.

• Pilot-assisted hydraulic controls for boom,forks, frame, auxiliary and outriggers.

• Optional Personnel Work Platform (PWP) System.

• Increased load capacity on the RS6to 6,600 lbs.

RS Series Telescopic Handlers

95

4

684-

12-1

0

TELESCOPIC HANDLERS

SPECIFICATIONSDL7-44 DL9-44 DL11-44 DL11-55 DL12-40

DIMENSIONS, MEASURES & WEIGHTSOverall Length – less forks (m) 20'7" (6.3) 20'7" (6.3) 20'7" (6.3) 20'10" (6.4) 19'4' (5.9) Overall Height (m) 7'11" (2.4 7'11' (2.4) 7'11" (2.4) 7'11" (2.4) 7'11" (2.4) Overall Width (m) 8'1' (2.5) 8'3' (2.5) 8'3" (2.5 8'3" (2.5) 8'3" (2.5) Ground Clearance (mm) 16" (400) 16" (400) 16" (400) 16" (400) 16" (400) Outside Turning Radius (m) 12'2" (3.7 12'2" (3.7) 12'2" (3.7) 12'2" (3.7) 12'2" (3.7) Wheel Base (m) 10'8" (3.3) 10'8" (3.3) 10'8" (3.3) 10'8" (3.3) 10'8" (3.3) Fuel Capacity (L) 30 gal. (114) 30 gal. (114) 30 gal. (114) 30 gal. (114) 30 gal. (114) Hydraulic Oil Reservoir Capacity (L) 45 gal. (170) 45 gal. (170) 45 gal. (170) 45 gal. (170) 45 gal. (170) Operating Weight lbs. (kg) 23,250 (10,546) 24,650 (11,181) 25,400 (11,521) 28,460 (12,909) 25,300 (11,475) LIFT PERFORMANCERated Lift Capacity lbs. (kg) 11,000 (4999) 9,000 (4082) 11,000 (4990) 11,000 (4990) 12,000 (5443) Boom Length 44' 55' 40'Maximum Lift Height (m) 44'4" (13.5) 44'4' (13.5) 44'4' (13.5) 55'1" (16.8) 40'4" (12.3) Max. Lift Capacity @ Max. Lift Ht. lbs. (kg) 6,000 (2722) 7,000 (3175) 8,000 (3628) 5,000/ 5,500 (2268/2495)* 10,000 (4536) Maximum Forward Reach (m) 30'6" (9.2) 30'6" (9.2) 30'6" (9.2) 40'9" (12.2) 26'4" (8.0) Max. Lift Capacity @ Max. Fwd. Reach lbs. (kg) 1,000 (454) 1,500 (680) 2,000 (907) 2,000 (907) 2,000 (907) LOADER PERFORMANCEBreakout Force lbf. (kN) 11,000 (48.9) 12,500 (55.6) 14,000 (62.2) NA 14,000 (62.2) Maximum Dump Height (m) 42'11' (13.1) 42'11' (13.1) 42'11' (13.1) NA 39' (11.9) Max. Forward Reach @ 45° Dump Angle (m) 14’3” (4.3) 14’3” (4.3) 14’3” (4.3) NA 11"10" (3.6) Dump Angle @ Max. Dump Height 24° 24° 24° NA 24° Maximum Loadover Height (m) 44'2" (13.4) 44'2" (13.4) 43'11" (13.4) NA 40'3" (12.3) Max. Dump Height @ 45° Dump Angle (m) 34' (10.4) 34' (10.4) 34' (10.4) NA 30'9" (9.4) Max. Forward Reach @ Max. Dump Ht. (m) 2' 3" (686) 2' 3" (686) 2' 3" (686) NA 1'2" (356) Rollback @ Ground Level 30° 30° 30° NA 30° Total Degrees of Bucket Rotation 132° 132° 132° NA 132° ENGINEEngine: John Deere 4045T Yes Yes Yes Yes YesTransmission: 4-Speed / Power-Shift Yes Yes Yes Yes YesPower (kW) 115 hp (86) 115 hp (86) 115 hp (86) 115 hp (86) 115 hp (86)Max. Travel Speed (km/hr.) 22 mph (35.4) 22.8 mph (36.7) 22.8 mph (36.7) 22.8 mph (36.7) 22.8 mph(36.7) Steering 2-Wheel • 4-Wheel • CrabBrake Oil-Immersed, Disc-typeParking Brake Hydraulic Release Spring-Applied

FEATURES AND BENEFITS• Industry-leading turning radius of 12' 2" offers excellent

maneuverability in confined spaces. • Low-profile design allows it to easily pass under 8' doorways.• All Dynalift Telescopic Handlers have 4-wheel, 2-wheel drive

and 4-wheel crab-type steering.• Side-mount engine design for easy maintenance access.• Hydraulic frame leveling.• Pilot assist multi-function joy stick.• Automatic rear axle stabilization.• Tight turning radius.• Spacious, ergonomically designed operator station.• Personnel Work Platform System.• Standard 115 hp turbo charged engine.

DL Series Dynalift®

*With outriggers down.

• Maximum load capacities range from 7,000 to 12,000 pounds.

• Choice of low or high boom profiles.

• Boom length options with maximum lifts of 40', 42', 44' and 55'.

• Choice of lift- or loader-oriented tools.

96

2865

-1-1

0

CARRIER/WHEEL LOADER

THE ULTIMATE OFF ROAD CARRIERFor safe operation on slopes, soft terrain and other potentially hazardous jobsites, the distinctive features on the Yanmar Carriers reduce risk and improve safety. Yanmar offers 3 Track Carriers with maximum payload rated at 2,540 lbs., 5,510 lbs. and 8,380 lbs. The compact model C12R offersoptional 3-way dumping with a 0.48 heaped dump body capacity.The newest C30R-US is powered by a 3 cylinder 32.9 hp Yanmardiesel with travel speeds up to 6.8 mph. And the larger C50R featuresOne-Touch Reversible Seat; creeper gearing and a powerful 91 hpYanmar 4 cylinder EPA Compliant TNV diesel engine.

The C12R Carrier Compact• Versatile.• Smooth HST Transmission.• Only 38" wide for work in close quarters.• Carry up to 0.48 cu. yd. heaped load.• Loaded ground pressure of just 5.83 psi.• Soft ground will love the C12R.

COMPACT WHEEL LOADERClass Leading Lift CapacitiesYanmar offers two sizes of articulated wheel loaders - the .52 cu. yd.and the .65 cu. yd. Each model offers the same high performance, comfort and quality features that experienced contractors require.

• Class leading lift capacities V3 - 6,030 lbs., V4 - 6,945 lbs.

• Ultra smooth hydraulic performance.• Single lever operation with automatic

bucket leveling.• Two-Mode control; choose fully automatic

shifting or fixed speed mode.• Rear Axle Oscillation transverse and

delivers smooth power over uneven terrain.• Powerful Yanmar 3 cylinder TNV EPA

Compliant Diesel power.

C12R

97

4

2865

-2-1

0

EXCAVATORS

ViO17 ViO20-3 ViO27-5B ViO35-5B ViO45-5B ViO55-5B ViO75-C

Operating Weight (Canopy) lbs. 3,836 4910 4910 7,850 10,275 11,532 17,530

Operating Weight (Cabin) lbs. 8,140 10,562 11,819 17,640

Yanmar Engine/ModelHP (net) HP (gross)

3TNV7013.5 hp/2200 rpm

3TNV7619.2 hp/2400 rpm20.1 hp/1400 rpm

3TNV7619.2 hp/2400 rpm20.1 hp/1400 rpm

3TNV8828.0 hp/2300 rpm

4TNV8839.5 hp/2400 rpm39.5 hp/2400 rpm

4TNV8839.5 hp/2400 rpm39.5 hp/2400 rpm

4TNV9858.2 hp/2000 rpm59.6 hp/2000 rpm

Digging Force (Bucket) lbs.(Arm) lbs.

3,417 1,918

3,987 3,057

4,6783,057

7,220 4,410

6,7224,995

7,5985,062

13,8597,284

Hydraulic Pump Type 2 x Piston, 2 x Gear

3 x Piston,1 x Gear

3 x Piston,1 x Gear

2 x Piston, 2 x Gear




Pump Capacity gpm 15.3 20.2 20.2 30.6 34.9 55.7

Auxiliary Flow gpm 8.1 11.3 11.3 17.4 19.7 21.3 33.8

Main Relief Set Pressure psi 2417 2988 2988 3200 3133 3553 3,553

Travel Speed (Low/High) mph 1.3/2.7 1.4/2.7 1.4/2.7 1.7 mph/2.9 mph 1.4/2.8 mph 1.4 mph/2.7 mph 1.7 mph/2.9 mph

Traction Force/ Draw Bar Pull lbs. 4,183 4,851 4,851 7,894 9,107 12,039 13,406

Fuel Tank Capacity gal. 5.3 7.5 7.5 11.1 16.9 16.9 26.4

Hydraulic Tank Capacity gal. 4.4 7.9 7.9 11.1 15.1 Ground Contact

Pressure psi 4.1 4.0 4.0 47/4.68(cabin/canopy)

4.31/4.19(cabin/canopy)



Lifting Capacity lbs.(Ground Level at MAX)

859 at 8'3" - 1,157 at 6'7" - 1,631

1,180 at 8'2" - 1,808 at 6'7" - 2,488

1,180 at 8'2" - 1,808 at 6'7" - 2,488

1,799 at 11'6" - 2,520 at 9'10" - 3,104 at 8'2" - 4,006

2,115 at 13'2" - 2,564 at 9'10" - 3,638 at 8'2" - 4,494

2,209 lbs.at 13'2" - 3,111at 9'10" - 4,494at 8'2" - 5,585

3,682 lbs.at 16'5"-3,682 at 13'1"-5,722

at 9'10" - 7,927

YANMAR Vio SeriesTrue Zero Tail Swing Excavators

98

2865

-3-1

0

EXCAVATORS

A B C D E F G H I JVio17 7'3" (2200) 7'7" (2310) 6'8" (1850) 12'2" (3710) 11'4" (3450) 5'0" (1525) 12'1" (3690) 8'8" (2630) 5'0" (1535) 7'7" (2300)

Vio20-3 8' (2440) 8'7" (2620) 6'3" (1900) 13'8" (4160) 12'10"(3915) 6'2" (1890) 13'1" (4000) 8' (2450) 6'7" (2010) 7'10" (2400)

Vio27-5B 9' (2750) 9'6" (2900) 7'9" (2350) 15'1" (4590) 13'9" (4190) 6'7" (2010) 15'2" (4620) 9'7" (2910) 6'11" (2120) 8'3" (2510)

Vio35-5B 10'10" (3300) 11'4" (3450) 9'4" (2850) 17'2" (5220) 15'1" (4610) 6'11" (2112) 17'5" (5300) 11'8" (3550) 7'1" (2150) 8'3" (2510)

Vio45-5B 12'1" (3680) 12'8" (3850) 8'10" (2700) 19'1" (5820) 17'3" (5260) 8'7" (2620) 19'6" (5950) 12'10" (3910) 7'8" (2340) 8'7" (2620)

Vio55-5B 13'1" (3980) 13'8" (4160) 9'6" (2900) 20'4" (6200) 18'3" (5560) 8'7" (2620) 21'2" (6440) 14'5" (4400) 7'7" (2320) 8'7" (2620)

Vio75-C 12'1" (3680) 12'8" (3850) 8'10" (2700) 19'1" (5820) 17'3" (5260) 8'7" (2620) 19'6" (5950) 12'10" (3910) 7'8" (2340) 8'7" (2620)

K L M N O P Q R SVio17

10" (260)3'1" (950)4'1" (1280) 9" (230) 7" (175) 5" (125) 2'01" (640) 1'04" (400) 3" (85) 2'1" (R640)

Vio20-3 1'13" (360) 4'6" (1380) 10" (250) 11" (280) 8" (200) 2'4" (700) 1'7" (485) 4" (95) R2'3" (690)

Vio27-5B 1'2" (350) 5'1" (1550) 10" (260) 1'1" (317) 6" (165) 2'9" (835) 1'7" (490) 4" (100) R2'7" (R775)

Vio35-5B 1'5" (435) 5'1" (1550) 1'0" (300) 1'1" (319) 8" (215) 2'9" (835) 1'7" (490) 6" (150) R2'7" (R775)

Vio45-5B 1'8" (500) 6'5" (1950) 1'2" (360) 1'2" (360) 2" (40) 2'7" (795) 2'2" (650) 5" (130) R3'2" (R975)

Vio55-5B 1'8" (500) 6'6" (1990) 1'4" (400) 1'2" (360) 2" (45) 2'7" (795) 2'2" (650) 5" (130) R3'3" (R995)ViO75-C 1'6" (460) 7'5" (2270) 1'6" (450) 1'3" (380) 7" (180) 2'6" (770) 1'10" (550) 1" (30) 3'8" (1130)

Dimensions Unit: ft. in. (mm)

Easy and Comfortable Operation of True Zero Tail SwingCommon Zero Tail models kept the overhang duringturning to within just 10 percent of the crawler’s width.VIO Series achieves the ultimate goal of no overhang atall. Since the counterweight and the front corners neverextend beyond the machines’ width, there is not anyconcerns even on jobsites which are right up against a wall.

The Equal Performance of Stability withConventional ModelsThe wide spacing of the distinctive YANMAR OffsetTracks achieves a good grip on the ground. The out-standing balance is further enhanced by the large counterweight. VIO Series also has VICTAS (VIO CrawlerTechnology By Advanced Stability) which provides anexpanded track gauge for more stability.

Fast and Easy Bucket Attachment ChangingThe Quick Coupler makes the once troublesome task ofchanging buckets fast and easy without even gettingyour hands dirty. It’s all performed by switch operationwhile you remain seated, except for fitting and removalof the safety lock pin. It can also use attachments madeby other companies, thereby reducing storage costs andsaving space.

Environmental Clean and Silent YANMARDiesel EngineEquiped YANMAR Clean and Silent Diesel Engine withEGR system, in full compliance to Stage III A EC (EU)and the I - Tier 3 EPA (U.S.A.) regulations with cleanexhaust and powerful output.

99

4

2996

-1-1

0

COMPACT UTILITY LOADERS

100

Boxer 300 Series Compact Utility Loaders

• Tip capacity of 1,250 lbs.• Operating capacity: 625 lbs. at 50% tip load.• Operating capacity: 438 lbs. at 35% tip load.• Under 35" wide, fits through standard gate.• Dedicated oil cooler to better manage hydraulic heat generation.• Stand-On Platform for operator safety and comfort.• Well balanced and stable, excellent ground speed and skid steer style controls.

Boxer 400 Series Compact Utility Loaders• Tip capacity of 1,800 lbs.• Operating capacity: 900 lbs. at 50% tip load.• Operating capacity: 600 lbs. at 35% tip load.• Variable flow hydraulics.• Dedicated oil cooler to better manage hydraulic heat generation. • Stand-On Platform for operator safety and comfort.• Well balanced and stable, excellent ground speed and skid steer style controls.

Boxer 500 Series Compact Utility Loaders• Tip capacity of 2,100 lbs. (526DX), 1,650 lbs. (530X)• Operating capacity: 1,050 lbs. (526DX), 825 lbs. (530X) at 50% tip load.• Operating capacity: 735 lbs. (526DX), 578 lbs. (530X) at 35% tip load.• Variable flow hydraulics.• Variable track widening system.• Dedicated oil cooler to better manage hydraulic heat generation. • Stand-On Platform for operator safety and comfort.• Well balanced and stable, excellent ground speed and skid steer style controls.

Specifications Model #320 Model #322D Model #427 Model #427W Model #532DX Model #530XEngine Power: 20 HP 22 HP 27 HP 27 HP 32 HP 30 HPEngine Manufacturer: Kohler Kubota Kohler Kohler Kubota Kohler Engine Description: Command Pro Gas D2902 Diesel Command Pro Gas Command Pro Gas D1105TD Diesel Command Pro Tip Capacity: 1250 lbs. 1325 lbs. 1800 lbs. 1800 lbs. 2100 lbs. 1650 lbs. Hydraulic Pressure: 3000 psi 3000 psi 3000 psi 3000 psi 3000 psi 3000 psiDump Height: 54" 54" 55.5" 55.5" 60" 60"Travel Speed: 3.4 mph 3.4 mph 3.5 mph 3.5 mph 3.7 mph 3.7 mph Ground Clearance: 5" 5" 7" 7" 5" 5" Ground Pressure: 3.2 psi 3.3 psi 3.6 psi 3.6 psi 3.4 psi Overall Length (without bucket): 68" 68" 70" 69.75" 77" 77" Operating Capacity, 35% of tip load: 438 lbs. 464 lbs. 600 lbs. 600 lbs. 735 lbs. 578 lbs. Operating Capacity, 50% of tip load: 625 lbs. 663 lbs. 900 lbs. 900 lbs. 1050 lbs. 825 lbs. Hydraulic Auxiliary Flow: 8 gpm 9.4 gpm 12.6 gpm 12.6 gpm 14.5 gpm 14.5 gpm Flow Ground Drive: 3 gpm 9.4 gpm 0-12.6 gpm 0-12.6 gpm 0-14.5 gpm 0-14.5 gpmOverall Width (fully extended): 34.5" 34.5" 43.5" 43.5" 35-43.5" 35-43.5" Overall Operating Height (fully raised): 92" 92" 93" 93.25" 98" 98" Weight (without bucket): 1740 lbs. 1900 lbs. 2354 lbs. 2354 lbs. 2671 lbs. 2445 lbs. Hinge Pin Height (fully raised): 70" 70" 70" 70" 76" 76"Track Width: 7" 7" 9" 9" 9" 9"

2996

-3-1

0

COMPACT UTILITY LOADERATTACHMENTS

101

Standard Bucket100 lbs.4.0 cu. ft. w/ straight edge 44" W x 27" L (Bolt on tooth bar available)

Hydraulic 4-in-1 Bucket250 lbs. / 4.0 cu. ft. 20" H x 42.5" W x 27.5" L

Cement Bowl75 lbs.2.2 cu. ft. attaches to auger power head 20" H x 25.5" W x 22.5" L

Angle Blade - 48"300 lbs.Backfilling or grading, snow removal 22" H x 48" W x 29" L

Power Rake350 lbs.Manual anglingPrepares soil for seeding or sodding24" H x 58" W x 35.5" L

Rotary Angle Broom492 lbs.For sweeping sidewalks or snow removal29.6" H x 51.25" W x 43" L

Eliminator240 lbs.For scarifying and debris removal 18" H x 42" W x 22" L

McCullough Cover-up100 lbs.For backfilling trenches42"/56.5" W x 27" L

Heavy-DutyGrapple Fork250 lbs.Grabs limbs and rocks for removal 32" H x 42" W x 32" L

Tiller250 lbs.6" digging depth20" H x 40" W x 24" L

Plate Compactor510 lbs.Plate: 43" x 48"24" H x 43" W x 33" L / 1900 VPM

Backhoe – 863 lbs.Comes with 12" bucket w/ Upfit Kit 69" H x 42" W x 116" L

Hydraulic Sod Layer100 lbs.Handles up to a half roll of sod10.5" H x 38" W x 50" L

Adjustable Forks162 lbs.Complete unit30" H x 32" L

Turf Cutter180 lbs.12" cutting width

4' - 5' rods, 1-3/4" mole, 2-1/2" reamer(Rod & Reamer Kit sold separately)

Bore Drive Head andRod & Reamer Kit200 lbs. (bore drive head)120 lbs. (kit)

Concrete Breaker320 lbs.Impact rate 550-950 bpm10.5" H x 25" W x 55.5" L

Rubble Bucket200 lbs.Removes rocks from tilled or loose soil18.5" H x 48" W x 22" L tines

Standard Trencher450 lbs.36" digging depth / 6" combo chain24" H x 46" W x 36" L

Hydraulic Tree Forks170 lbs.Open to 30" Wide12.5" H x 25" W x 47" L

High Torque Auger Power Head170 lbs.Auger drive unit14" H x 24" W x 27.5" L

Leveler/Carry-All134 lbs.16" H x 48" W x 24" LFor grading, backfilling trenches and

carrying materials

Grapple Bucket260 lbs.32" H x 44" W x 32" L

Augers – 6" - 36" diameter auger bits available42" long / 2-9/16" round hub / 24" auger extension available separately

Multi-Purpose Tool (Tow ball not included) – 120 lbs.11.5" H x 24" W / Rippers, tree broom, tow hitch

4

574-

11-1

0

102

STUMP GRINDERS

With different models, sizes,options and durable designs,Morbark has the right stumpgrinder to fit any application.

MorbarkMorbark®® D 76 TD 76 Trackrack

MorbarkMorbark®® D 52 SPHD 52 SPH

EQUIPMENT HIGHLIGHTS

• Patent-pending cutter arm system with long boom technologyand hydrostatic drive.

• Piloted flange cutter head bearings increase bearing life and minimize exposure to dirt and debris.

• Stationary engine design maintains a low center of gravityand increases stability.

• Tail mounted operator’s control station allows maximum visibility of grinding area. (D 52 SPH, D 76 SP 4 x 4)

• Hydrostatic motor with gear pump and hydrostatic transmission.

Morbark stump grinders offer the widestboom swing arc radius in the business.

D 52 SPH......................................52"D 76 SP 4 x 4 / D 76 Track ..........76"D 86 Track ....................................86"

SPECIFICATION D 52 SPH D 76 SP 4 x 4 D 76 Track D 86 Track

Length 123"-139" 144"-160" 144"-160" 174"-190"

Width 35" 35"-52" 35"-47" 35"-47"

Height 66" 60" 62" 70"

Weight 1,720 lbs. 3,680 lbs. 4,880 lbs. 5,760 lbs.

Engine Kubota Caterpillar or Perkins Kubota Kubota

Horsepower 34-44 HP 62 HP 66-84 HP 84-99 HP

Fuel capacity 10 gallons 10 gallons 23 gallons 23 gallons

Hydraulic oil capacity 15 gallons 30 gallons 43 gallons 43 gallons

Boom arc swing 52" 76" 76" 86"

Boom travel up 19" 19" 19" 12"

Boom travel down 12" 14" 14" 19"

Tires / Track Tires (4) 5.70-8 Tires (6) 20 x 8.0-10 Tracks 72" L x 9" W Tracks 72" L x 9" W

Primary drive Hydrostatic Hydrostatic Hydrostatic Hydrostatic

Secondary drive Poly belt Poly belt Poly belt Poly belt

Cutter wheel speed 1,200 RPM 1,200 RPM 1,200 RPM 1,250 RPM

Fully machined boom pivot assembly pivots on heavy-duty king pins within a lubricated assembly designed toreduce component flux and provide years of trouble-free service.

574-

12-1

0

103

CHIPPERS

MorbarkMorbark®® Beever™ M8DBeever™ M8DMorbarkMorbark®®Beever™ M18RBeever™ M18R

SPECIFICATIONS M12R TRACK M12R M14R M15R M20R TRACK M20RLength 14' 8" 15' 9" 15' 6" 16' 2" 17' 2" (w/o infeed deck)

21' 4" (with infeed deck) 19' 1"

Height 8'-9' 8' 5" 8' 10" 8' 11" 9'-10' 9' 2"

Width 6' 3" 5' 11" 6' 11" 7' 1" 8' 2" 8' 5½"

Gross weight 6,414 lbs. 5,500 lbs. 6,050 lbs. 7,500 lbs. 18,240 lbs. 13,900 lbs.

Chipping capacity 12" 12" 14" 15" 20" 20"

Horsepower 84-115 HP 84-115 HP 115-125 HP 140-170 HP 325-350 HP 325-350 HP

SPECIFICATIONS M6R M8DOperating length 12' 8" 15'

Transport length 11' 6" 12' 7"

Height 6' 2" 7' 4"

Width 4' 8" 5' 3"

Gross weight 1,770 lbs. 2,150-2,750 lbs.

Chipping capacity 6" 8"

Horsepower 27 HP 35-44 HP

SPECIFICATIONS M18RLength (single axle)

(tandem axle)17' 8"18' 7½"

Height 9' 6"

Width (single/tandem axle)(single axle dual wheel)

7' 7"8' 5"

Gross weight 10,200 - 12,200 lbs.Chipping capacity 18"Horsepower 140-275 HP

EQUIPMENT HIGHLIGHTS• Direct Drive.• Single top feed wheel compression system with spring

assisted down pressure.• Automatic feed system.• Folding infeed tray.

EQUIPMENT HIGHLIGHTS• 2" x 6", fully boxed, extended steel frame.• Patent pending Variable Force™ hydraulic down pressure

system with 700 lbs. of perpetual down pressure.• Reversing automatic feed system.• Patented 36" diameter staggered knife pocket drum with (4) 10-

1/2" long chipping knives, removable knife holders and 36" diameter, 8-blade, chambered air impeller system.

• B-loc chipper drum bushings provide secure shaft mounting and eliminate “drum walking” associated with taper lock bushings.

• Additional 1000 lbs. of yoke down pressure at valve handle.

EQUIPMENT HIGHLIGHTSMorbark® Beever™ M12R Track• 72" long x 9" wide rubber track drive system.• Multi-function radio remote control with

tethered back-up system.• 1612 in.2 infeed opening with 180 in.2

throat opening.• Steel guard enclosing valve bank components.

Morbark® Beever™ M12R• 18" top feed wheel with combination serrated

teeth and knife bars.• Drive belt inspection cover provides ease of

drive system maintenance.• Hydra-Lift Compression system with spring

assisted down pressure.• 360º manual crank swivel discharge.

Morbark® Beever™ M14R / M15R• TorqMax™ Top Feed Wheel Compression

System with 3:1 torque amplification.• 21" diameter, 8-blade,

chambered air-impeller system.

• 360º manual crank swivel discharge with infinite rotation.

• Reliable and proven Twin Disc friction clutch.

• Reversing Automatic Feed System reduces wear and increases knife life.

• Variable Force™ Hydraulic Down PressureSystem creates 600 lbs. of perpetual down pressure. (M15R)

M20R Track• Caterpillar 312B track drive system.• 15-function radio remote control with tethered

back-up system.• 28" wide infeed opening provides straight, flow

through material passage.• Bearing style pivot assembly contours the

radius of the drum.

M20R• TorqMax™ Plus Top Feed Wheel Compression

System with 2:1 torque amplification.• 36" diameter, 6-knife staggered knife pocket

drum with chambered, 4-blade air impeller system

• Reversing Automatic Feed system withPDCJ1939 Auto Sense™ controller reduceswear and increases knife life.

• Variable Force™ Hydraulic Down PressureSystem creates 450 lbs. of perpetual down pressure.

MorbarkMorbark®® Beever™ M14RBeever™ M14R

4

2962

-1-1

0

AUGERS

104

AUGERSEDGE Planetary Drive The gear reduction drive units are designed for heavy-duty use in commercial and industrial applications. Planetary drive features high torque, easy hookup and heat treateddrive shafts.

Model Hydraulic Requirement Max. Auger Bit Size Theo torque @ 2500 psi Average SpeedPA-225EU 15-30 gpm (56-113Lpm) 36" (914mm) 2531 lbs.ft. - 3431 Nm 49 rpm @ 20 gpm

2-9/16" STANDARD DUTY AUGER BITS – Feature a reinforced fabricated boring head and doublewrapped flighting, heat treated teeth and “fishtail” center point. They are approximately 50" in overall length and availablefor round or hex drive augers.

Part No. Description Bit Size No. of Teeth Overall Length Wgt. lbs. 501208 4" (102mm) Auger Bit - Round 4" 2 50" 41502565 6" SQ (152mm) Auger Bit - Round 6" 2 50" 55502566 9" SQ (229mm) Auger Bit - Round 9" 4 50" 89502567 12" SQ (305mm) Auger Bit - Round 12" 4 50" 110502568 15" SQ (381mm) Auger Bit - Round 15" 6 50" 126502569 18" SQ (457mm) Auger Bit - Round 18" 6 50" 163502570 20" SQ (508mm) Auger Bit - Round 20" 7 50" 180502571 24" SQ (610mm) Auger Bit - Round 24" 9 50" 200502572 30" SQ (762mm) Auger Bit - Round 30" 11 50" 260502573 36" SQ (914mm) Auger Bit - Round 36" 13 50" 340

Part Number Description Weight501854 PA225EU Planetary Round Auger Drive (does NOT include mount, hoses or couplers) 370 lbs.

2-9/16" Round

Auger Mounts are available for Case, Caterpillar, Ford, Gehl/Mustang, John Deere, Kobelco, Komatsu, Kubota, IHI, Scat Trak, Takeuchi,Terex, Thomas and Volvo excavators in numerous different models.

AUGER MOUNTS

2-9/16" TREE AND SHRUB AUGER BITS – Are designed with smaller diameter auger flighting atthe bottom, which leaves a space for root balls, fertilizer or mulch.

Part No. Description Bit Size No. of Teeth Overall Length Wgt. lbs.502574 TSQ 18" (457mm) Tree & Shrub Auger Bit - Round 18" 8 42" 117502575 TSQ 24" (610mm) Tree & Shrub Auger Bit - Round 24" 9 42" 160502576 TSQ 30" (762mm) Tree & Shrub Auger Bit - Round 30" 12 42" 270502577 TSQ 36" (914mm) Tree & Shrub Auger Bit - Round 36" 14 42" 348

2-9/16" STANDARD ROCK AUGER BITS – Feature a reinforced fabricated boring head, doublewrapped flighting, conical carbide teeth and a standard “fishtail” center point. These bits are not intended for use in concrete or asphalt applications.

Part No. Description Wgt. lbs.500877 6" (152mm) Rock Auger Bit with Standard Point - Round 75501158 24" (610mm) Rock Auger Bit with Standard Point - Round 178501159 36" (914mm) Rock Auger Bit with Standard Point - Round 286

2-9/16" CONICAL ROCK AUGER BITS – Feature a reinforced fabricated boring head, double wrapped flighting, conical carbide teeth and a conical “bullet-tooth” center point. These bits are not intended for use in concrete or asphalt applications.They are available in 9", 12", 15", 18" and 24" bit sizes.

2962

-2-1

0

BUCKETS / GRAPPLES

105

BUCKETSCEAttachments offers more than 60 skid-steer dedicatedbuckets to choose from. Options include: dirt/constructionbuckets, low profile, bulk material/snow buckets andgeneral purpose buckets.

EDGE® Dirt/Construction BucketsEDGE dirt buckets have a back height of 20.5" (20.75" for heavy-duty dirt buckets) and front to back depth of 37". Often used inheavy digging conditions or in grading. Bolt-on edges and tooth-bars are common accessories for these buckets.

Part No. Description Wgt. lbs.501383 60' Extended dirt bucket 3/4" x 6" edge 460501361 60" Extended dirt bucker w/6 weld-on teeth 495501384 66" Extended dirt bucket, bolt-on edge 490501362 66" Extended dirt bucket w/7 weld-on teeth 531501385 72" Extended dirt bucket, bolt-on edge 575501976 72" Heavy-duty dirt bucket w/8 weld-on teeth 747501640 72" Heavy-duty dirt bucket, bolt-on edge 700501363 72" Extended dirt bucket w/8 weld-on teeth 622501724 78" Extended dirt bucket w/9 weld-on teeth 673501606 78" Extended dirt bucket, bolt-on edge 620502508 78" Heavy-duty dirt bucket, bolt-on edge 735501884 78" Heavy-duty dirt bucket w/9 weld-on teeth 788501605 84" Extended dirt bucket, bolt-on edge 655501569 84" Heavy-duty dirt bucket w/9 weld-on teeth 828501639 84" Heavy-duty dirt bucket no bolt-on edge 775502506 84" Extended dirt bucket w/10 weld-on teeth 714501300 90" Heavy-duty dirt bucket w/10 weld-on teeth 869501882 92" Heavy-duty dirt bucket no bolt-on edge 810502509 96" Heavy-duty dirt bucket no bolt-on edge 845502510 96" Heavy-duty dirt bucket w/11 weld-on teeth 909

Dirt buckets offer the greatest breakout force, excellent visibility to the cutting edge, and lowest capacity. They are used for construction, landscaping or other heavy-duty applications.

GRAPPLESDesigned for handling awkward materials such as logs, treestumps, brush or other loose materials. Full featured grapples include hardened pin, cushioned cylinder kit andcylinder hose guard.

BRUSH ROOT RAKE – HEAVY-DUTY BTRPart No. Description Wgt. lbs.

502604 BTR 78" (1981mm) Brush/Trash/ 993Root Rake with Grapple –Full Feature Universal Mount

Model Open Height No. of Tines CylinderBTR 78" HD 44.9" 8 Cushioned

GRAPPLE BUCKET– Standard-DutyPart No. Description Wgt. lbs.

502675 GB66U: 66" (1727mm) Standard- 847Duty Grapple Bucket Universal Mount - includes hosesand couplers

Model Width Opening Height End Plates

GB 66 66" 51" Not available

The grapple bucket attachment’s basic design allows it to load and grapple large and/or uneven objects as well as clean up thesmallest debris. Our grapple buckets feature enclosed cylindersand hoses to protect against debris and stray limbs. 4

2962

-4-1

0

BACKHOE / TRENCHER

106

BACKHOESThe backhoe attachment gives you the power to handleexcavation jobs with your skid steer loader, dig utilitytrenches and septic tanks quicker.Metered spools on the control valves produce smooth andprecise control of the backhoe movement. The operatorplatform has a tapered console for increased foot area andgreater operator comfort.

EDGE® BACKHOES, SKID STEER

Model Dig Depth Optimum Performance With: Dig Force Stabilizers/WidthBH509 9'8" 8-12gpm (36-55Lpm) Hydraulic Systems 5676 lbs. (25.2kN) Fold-Down 7'11"

MAIN FRAME:Part No. Description Wgt. lbs.500324 BH509 Backhoe Base Unit (add backhoe and loader half mounts and bucket) 1425502536 BH609 Backhoe Base Unit with vertical stabilizer (add backhoe and loader half

mounts and bucket) 1460

OPTIONS:500814 Rubber Stabilizer Pad Set for 509 Backhoe 70

TRENCHERSFeatures of these trenchers include a 50,000 lb. (22,680kg)digging chain, removable double-flighted spoil auger andsealed, tapered roller bearings in the nose. Includeshoses and couplers.

MODEL XR-14 – 48" Depth Model Hydraulic Requirement Hydraulic System Cutting Width Cutting DepthXR14 10-20 gpm (38-75 Lpm) Standard Flow 6", 8", 10", 12" 48"

Universal Mount

48" DepthPart No. Description Wgt. lbs.502541 XR-14 Trencher 48" x 6" width, with half rock and frost, Gehl ’25 series mount 750502539 XR-14 Trencher 48" depth x 6" width, single standard chain, Universal mount 800502540 XR-14 Trencher 48" depth x 6" width, double standard chain, (ABF) Universal 1035

2962

-6-1

0

LAND CLEARING ATTACHMENTS

107

Rakes

EDGE® Hopper Brooms

Model Hydraulic Requirement Picks up: No. of Teeth Bucket Capacity

FP66 10-25 gpm (37-94 Lpm) @2300 psi Rocks 1"-20" diameter 300 10.32 c.f. struck

Collect rocks and debris and till compacted soil to create theperfect seedbed. (Preparator is a registered trademark ofFFC/Sweepster, Inc.). Includes hoses and flat-faced couplers.

EDGE® Rotary Brush MowerBrush mowers from CEA feature a direct drive hydraulic motorrequiring 14-25 gpm. It is designed to cut through the thickestbrush and glide over the roughest terrain. Features a heavy-dutystump jumper and includes hoses and flat-faced couplers.

The bi-directional hopper broom is ideal for material pickup, roadmaintenance and jobsite cleanup. There is no caster wheel – soyou can get right up next to objects and have better contact withthe sweeping surface. Complete with hoses and couplers.

PREPARATOR®

Part No. Description Wgt. lbs.

500339 Universal Mount FP66U 66" (1676mm) Preparator 1340

502118 FP66U 66" (1676mm) Preparator for Gehl ’25 Series 1270

502220 FP66 66" (1676mm) Preparator for Gehl 4615 1270

Model Part No. Description Hydraulic Flow Wgt. lbs.

60S 501308 Universal Mount 60" (1524mm) Rotary Brush Mower 14-25 gpm 875

60S 501785 Mustang single pin 60" (1524mm) Rotary Brush Mower 14-25 gpm 875

Model Hydraulic Requirement Overall Width Brush Diameter Cubic Feet Heaped

RHB 72 14-25 gpm (53-94 Lpm) 77.8 (1976mm) 26" (660mm) 16.8

Part No. Description Wgt. lbs.

501657 RHB72: 72" (1828mm) Hopper Broom, Universal Mount 910

501821 RHB72: 72" (1828mm) Hopper Broom with Gehl ’25 Series 910

4

2962

-7-1

0

SKID STEER ATTACHMENTS

108

HARD SHOE TRACKS

Pallet Forks

Hard Tracks

Better traction can mean better performance. Surfacesmade slippery due to sand, snow, mud and rain may meanchallenges, but not excuses. Tracks from CEA provide protection and reduce tire wear in abrasive conditions.

CEA has every set of tracks for every skid steer loader, for10.00, 12.00, 14.00, 33-15.5-16.5 tires.

We can provide Ladder Style - Grouser, Hard Pad Style -Grouser, Soft Pad Style - Grouser, Ladder Style to fit yourmodel of skid loader.

Your Hawkins-Graves representative has charts to give you the Part No. for your required tracks as well as anyaccessories needed.

EDGE® Pallet Forks

Part Number Description Wgt. lbs.502287 Grouser hard shoe tracks to fit 12.00 tires - 48 pads (24 per side) 1055

will accommodate 38" to 40.5" wheelbase

Example:

Hydraulically controlled pallet fork rotation right from thecab of your skid steer loader. Tines are manually adjustable.

Part No. Description Capacity Degree of Rotation Length of Tines Wgt. lbs.501942 Rotating Pallet Fork 3700 lb. 180 Degrees 48" 700

Rotating Pallet Forks

Sliding Tine Pallet Forks

Side Shift Pallet Forks

Part No. Description Capacity Length of Tines Wgt. lbs.501731 Pallet Fork with sliding tines 3700 lb. 48" 560

Part No. Description Capacity Travel Length of Tines Wgt. lbs.501781 Side Shift Pallet Fork frame 3700 lb. 8" Right or Left 48" 790

2962

-9-1

0

THUMBS /EXCAVATOR BUCKETS

109

THUMBS

Hydraulic Thumb

Specifically designed to aid in handling or loading irregularshaped objects that a bucket alone can’t handle. Because it easilyretracts back against the dipper, it can be left on the machine during normal excavation.

RIGID, DUAL-TINE THUMBWhen ordering, please specify machine model number.

HYDRAULIC, DUAL-TINE THUMBHydraulic thumbs feature a cylinder to adjust thumb placement. These skid steer loader thumbs are available for Bobcat,Gehl/Mustang, Komatsu, Kubota, Scat Trak, Takeuchi, Terex,Thomas and Yanmar. Contact your Hawkins-Graves representative and when ordering, please specify machine model,bucket model and quick coupler used. Does not include hoses or hydraulic couplers

HEAVY-DUTY BUCKETS, EXCAVATORHeavy-duty buckets are designed for tough clay with rock scattered through the soil. They are not designed for the pryingrequired to dig solid rock. Extra heavy-duty buckets aredesigned for shot rock and demolition.

These excavator buckets are available for Bobcat, Gehl/Mustang,Daewoo, JCB, John Deere, Kobelco, Komatsu, Kubota, Nagano,Scat Trak, Takeuchi, Terex, Thomas, Volvo and Yanmar. Contactyour Hawkins-Graves representative with your machine model.

Ditching buckets are specifically designed for ditch constructionand maintenance. They are also useful in grading and slopework. They do not have teeth and are not designed for toughdigging applications.

Cemetery buckets are designed with extra bucket rotation incor-porated to enable the operator to dig the straight vertical wallsas well as flat bottoms.These buckets are available for Bobcat, Caterpillar,Gehl/Mustang and John Deere.

CEMETERY BUCKETS

DITCHING BUCKETS

4

3092

-2-1

0

110

HYDRAULIC COMPACTORS

Specifications TTC51-L/FC TC51-H/FC TC71 TC71/FC TC92 TC152-L TC152-H TC301-L TC301-H

Minimum Carrier Sizelbs. (kg)

2,000 (907)

2,000 (907)

5,500 (2,494)

5,500 (2,494)

7,700 (3,492)

15,400(6,984)

15,400 (6,984)

14,500(6,576)

14,500(6,576)

Maximum Carrier Size lbs. (kg)

10,000(4,535)

10,000(4,535)

15,500(7,029)

15,500 (7,029)

25,300 (11,474)

48,400 (21,950 )

48,400 (21,950)

105,600 (47,891)

105,600(47,891)

Operating Weight1

lbs. (kg)295

(134)295

(134)610

(277)610

(277)1,130 (512)

1,820 (825)

1,825 (828)

2,150 (975)

2,155 (977)

Impulse Force @ Min. RPM lbs. (kg)

1,930 (875)

1,930 (875)

2,600 (1,179)

2,600 (1,179)

5,500 (2,494)

11,130(5,048)

11,130(5,048)

16,330 (7,406)

16,330 (7,406)

Impulse Force @ Max. RPM lbs. (kg)

3,000 (1,361)

3,000 (1,361)

5,000 (2,268)

5,000 (2,268)

8,200 (3,719)

16,630 (7,542)

16,630 (7,542)

24,400 (11,066)

24,400 (11,066)

Ground Pressure @ Min. RPMpsi (bar)

7(0.48)

7 (0.48)

7 (0.48)

7 (0.48)

9.2 (0.63)

11.2 (0.77)

11.2 (0.77)

13.4 (0.92)

13.4(0.92)

Ground Pressure @ Max. RPM psi (bar)

10.9 (0.75)

10.9 (0.75)

13.6 (0.94)

13.6 (0.94)

13.7 (0.94)

16.7 (1.15)

16.7 (1.15)

20 (1.38)

20(1.38)

Minimum Flow Rate US gpm (lpm)

7.2 (27.2)

10.7 (40.4)

11.7 (44.2)

11.7 (44.2)

20.6 (77.9)

26.7 (100.9)

37.4 (141.4)

37.4 (141.7)

53.5(202.2)

Maximum Flow Rate US gpm (lpm)

12 (45.4)

18 (68.0)

16.3 (61.6)

22 (83.2)

25.2 (95.3)

32.7 (123.6)

45.7 (172.7)

45.7 (172.7)

65.3(246.8)

RPM @ Minimum Flow RPM 1,800 1,800 1,800 1,800 1,800 1,800 1,800 1,800 1,800

RPM @ Maximum Flow RPM 2,240 2,240 2,500 2,500 2,200 2,200 2,200 2,200 2,200

Operating Pressure @ Min. Flow2 psi (bar)

920 (63)

700 (48)

820 (57)

920 (63)

970 (67)

1,600 (110)

1,190 (82)

1,480 (102)

1,080(74)

Operating Pressure @ Max. Flow2 psi (bar)

1,135 (78)

860 (59)

1,130 (78)

1,230 (85)

1,200 (83)

1,964 (135)

1,460 (101)

1,820 (126)

1,330(92)

Max. Relief Valve Setting psi (bar)

2,800 (193)

2,800 (193)

2,800 (193)

2,800 (193)

2,800(193)

2,800 (193)

2,800 (193)

2,800 (193)

2,300(159)

FEATURES and BENEFITS:High Performance, Low Maintenance – Motor design requires minimal oilflow leaving sufficient oil for effective boom movement. Optional high or lowflow motor configurations allow you to match the motor to your specifichydraulic requirements. Flow control valves, standard on the TC51 and optional on the TC71, protect the rotating group from over-speeding, ensuring optimum operating speeds by returning excess flow to the tank.High frequency operation and high ground pressure are standard to achievemaximum proctor densities and high lifts.Internal anti-cavitation valves permit the motor to slow down safely after shutting off the control valve, eliminating shock loading to the rotating group.

Oil Bath Lubrication ensures continuous bearing lubrication and eliminates the need for manual greasing.

Rubber Isolators prevent vibration in the upper structure, delivering maximum energy through the base plate and into the soil, providing excellent proctor densities.The TC92 and TC152 lattice design places the isolators in compression not in shear. This extreme duty lattice design excels in continuous compacting applications, helping to resist extreme downwardforce while providing optimum dampening.

Mounting Brackets range in variety of configurations, including dedicated, swivel and variable pin center (QA), to meet most interface requirements.

Swivel Top Mounts are available on the TC71, TC92 and TC152 compactors. Controlled compaction is achieved by locking the swivel mount in different positions of 45 degree increments. By removing the pin, the compactor can “free float.”

Universal Adjustable Boss – Both the QA Swivel and QA Non-swivel mounts come with BTI’s unique adjustable bossmounting system which allows adjustment of the pin spacing to accommodate quick-coupler installations on most common rubber tire backhoes.

TC TC SERIESSERIES

Hydraulic CompactorHydraulic Compactorss

2861

-1-1

0

COMPACTION EQUIPMENT

Standard Equipment BT60/4

�� Electronic Ignition.�� Oil Lubrication.�� Corrosion-free plastic fuel tank.�� Polyethylene shoe with steel wear plate.�� Centrifugal clutch.�� Infinitely variable frequency.�� Safe operation, anti-vibration

handle with shut-down switch.�� Large capacity air filter.�� Diaphragm carburetor.�� Recoil starter with integral guard.�� Narrow bellows.�� Engine protection guards.

Dimensions in inches (mm)B H L L1 W

BT60/4 13.8 37.8 28.9 13.2 11.0(350) (960) (735) (335) (280)

BT60/4 Vibratory Tamper

TECHNICAL DATA BT60/4

WeightsBasic weight........................................ lbs. (kg) 134 (61)Operating weight CECE ......................lbs. (kg) 137 (62)

Driving Characteristics (depending on site conditions)Working speed max. ..............ft./min. (m/min) 65.6 (20)Area coverage max. ....................sq.ft./h (m2/h) 3616 (336)

Drive Engine manufacturer ........................................ HondaType .................................................................. GX 100 (4-cycle)Cooling .............................................................. AirNumber of cylinders ........................................ 1Performance ISO 9249 ........................hp (kW) 3.4 (2.5)Displacement ......................................in3 (cm3) 6.0 (98)Speed ........................................................rpm 4200Fuel.................................................................... gasolineFuel consumption max. ..................gal./h (l/h) 0.2 (0.8)Starting device .................................................. recoil starter

Vibratory SystemDrive system .................................................... mechanicalFrequency ..........................................vpm (Hz) 540-708 (10-11.8)Jumping Height ..................................in. (mm) 2.4 (60)Impact force ......................................lbs. (kN) 3035 (13.5)Compaction depth max. ......................in. (cm) 21.7 (55)

CapacitiesFuel ........................................................gal. (l) 0.8 (3)Lubricating oil (tamper cylinder) ............gal. (l) 0.3 (1)

Standard Equipment

�� Honda engine with oil alert.�� Vibration isolated engine.�� Removable, foldable, vibration isolated

steering handle.�� Wear resistant base plate with reinforced sides.�� Self-cleaning base plate.�� Engine protection frame.�� Balanced lifting point.�� Carrying handles.�� Bolt on exciter housing.�� Centrifugal clutch.�� Fully enclosed V-belt.

Dimensions in inches (mm)H H1 L L1 W

BVP18/45 21.1 36.0 43.9 22.0 17.7 (535) (915) (1115) (558) (450)

TECHNICAL DATA BVP18/45

WeightsBasic weight ......................lbs. (kg) 198 (90)Operating weight ................lbs. (kg) 201 (91)Surface load ............lb./in.2 (kg/m2) 00.81 (570)

DimensionsWorking width....................in. (mm) 17.7 (450)

Driving Characteristics (depending on site conditions)Working speed max. ft./min. (m/min.) 82 (25)Max. gradeability ........................% 30

DriveEngine manufacturer ...................... HondaType ................................................ GX 160Cooling ............................................ AirNumber of cylinders ........................ 1Performance ISO 9249 .... hp (kW) 4.8 (3.6)Speed ........................................rpm 3600Drive system.................................... mechanicalFuel ................................................ gasoline

Vibratory systemFrequency..........................vpm (Hz) 5400 (90)Centrifugal force ................lbs. (kN) 4050 (18)CapacitiesFuel........................................gal. (l) 1.0 (3.6)Water ....................................gal. (l) 1.8 (7)

BVP10/36, BVP18/45 Vibratory Plates

111

4

RAISING THE BAR:THE 1648 Plus PAVER

• Its 8'5" widthrequires less trailer space, leaving more room for additional equipment.

• Two fully-adjustable screed options provide paving widths from 4*-13' (*with cut-off plates and baffles).

• Two-burner propane heating system.

• Dual-speed ground drive system provides infinite paving controlto a maximum of 130 FPM in high range.

• 48 hp Yanmar diesel engine runsquietly and provides 10% morehorsepower than competitive models.

• Redesigned hydraulic hose-routing system.

SETTING THE STANDARD:THE 1448 Plus PAVER

• Compact 8'5" size makes it easy to transport and perfect for smaller jobs.

• A single-speed drive with 0-160 FPM forquick, efficient paves.

• Operator station features a single-span platform.

• Exhaust- or propane-heated screed.

684-

14-1

0

112

FEATURES:

• Convenient dual-controls on the left and right sides for one- or two-person operation.

• Excellent hopper visibility, whichallows for a smooth and efficientpaving job.

• Exhaust diverter valve (available onthe 1448), allows the operator tochoose between exhaust through themuffler. Dual-burner propane heat isstandard on the 1648.

PowerBox® Asphalt Pavers deliverwhat professional pavers need most:consistent performance and a qualitypaving job, which lead to repeat business and referrals. Designed tohandle all kinds of commercial andmunicipal appllications, thesemachines really perform for the contractors who make their livingfrom the platform of a paver.

Asphalt Box PaverSpecifications

1448 Plus 1648 Plus DIMENSIONS, MEASURES & WEIGHTSOverall Height (mm) 6' 11" (2108) 7' 1" (2172) Transport Width (mm) 8' 5" (2565) 8' 6" (2591) Operating Width (mm) 10' 9" (3277) 10' 5" (3175) Length (mm) 7' 4" (2235) 9' 7" (2921) Truck Clearance (mm) 23" (584) 23" (584) Operating Weight (kg) 7775 lbs. (3527) 10,600 lbs. (4808)

ENGINE Model Yanmar / Diesel Yanmar / DieselNet Power (kW) @ RPM 36 hp (27) @ 3000 rpm 48 hp (35.4) @ 3000 rpm Fuel Tank 8 gal. (30) 12.5 gal. (47.3)

SCREEDFull Floating & Adjustable (mm) 8-12" (2438-3658) 8-13" (2438-3962) Vibratory 2500 vpm – maximum 3000 vpm – maximum Exhaust-Heated Standard N/A Propane-Heated Option Standard Hydraulic Extensions (mm) 24" (610) w/strike-off 30" (762) w/ 6" (152) wear plate Crown / Invert Adjustment (mm) Dual Lever, 0"- 2" (0 - 51) Single Lever, 0"- 3" (0 - 76)

MATERIAL FLOW Independent Hydraulic Operated Gates Standard Standard Gate Cut-Off Plates (mm) Option, 6"- 36" (152 - 915) Option, 6"- 36" (152 - 915) Gravity Flow Asphalt Hopper Capacity (kg) 4 tons (3629) 6 tons (5443) Independent Hydraulic Operating Augers Located on the Gate Located on the Gate or Screed Extension

DRIVE CONFIGURATIONSpeed (m/min) Single, 0 - 80 FPM (24) Single, 0 - 130 FPM (40) Self-Adjusting, Steel Track (mm) 12" x 3" (305 x 76) 12" x 3" (305 x 76) Counter-Rotating Standard Standard

OPERATOR STATION Platform Single-Span Isolated Dual-Span Controls Left and Right Sides Left and Right Sides Muffler w/Exhaust Diverter Valve Standard N/A Wash-Down Stations (L) Single, 5 gal. (18.9) Dual, 5.5 gal. (21)

HYDAULIC SYSTEMVariable Hydrostatic Drive Pump (L/min) 17.0 gpm (64.4) 37.0 gpm (140.0) Hydraulic Auger Drive Pump (L/min) 7.5 gpm (28.4) 10.9 gpm (41.3) Hydraulic Cylinder Pump (L/min) N/A 10.9 gpm (41.3) Hydraulic Oil Cooler Capacity (L/min) 12.0 gpm (45.4) 32.0 gpm (121.1) Hydraulic Reservoir (L) 18.0 gal. (68) 20 gal. (76)

ASPHALT PAVER

2861

-4-1

0

TANDEM VIBRATORY ROLLERS

TECHNICAL DATA BW90AD-2 BW900-2 BW100AD-4WeightsBasic Weight with ROPS ................lbs (kg) 3053 (1385) 2502 (1135) 4807 (2180)Operating Weight .......................... lbs (kg) 3351 (1520) 2923 (1326) 5291 (2400)Average axle load............................ lbs (kg) 1675 (760) 1462 (663) 2646 (1200)Average static linear load CECE. pli (kg/cm) 47.0 (8.4) 41.2 (7.36) 67.2 (12.0)DimensionsWorking width .............................. in (mm) 35.4 (900)Length with ROPS ..........................in (mm) 76.1 (1934) 81.9 (2080) 97.4 (2475)Track Radius, inner ........................in (mm) 77.6 (1970) 63.8 (1620) 107.0 (2720)Driving Characteristics (depending on site conditions)Speed (with vibration) ..............mph (km/h) 0-2.8 (0-4.5) 0-2.5 (0-4.0) 0-4.0 (0-6.5)Speed (for transport) ................mph (km/h) 0-5 (0-8) 0-4.4 (0-7.0) 0-7.5 (0-12)Max. gradeability without/with vibration. ..% 40/30 40/30 40/30DriveEngine manufacturer.................................... Kubota Honda KubotaType ............................................................ D 722 E3B GX620 D 1703 MCooling - cylinders ...................................... water air waterNumber of cylinders .................................... 3 2 3Performance ISO 9249 (max) ........hp (kW) 16.6 (12.4) 17.7 (13.2) 33.8 (25.2)Speed (max) ........................................ rpm 3000 3600 2600.................................................................... Throttle position 1 2200.................................................................... Throttle position 2 2600

Electric Equipment ....................................V 12 12 12Drive System................................................ hydrostatic hydrstatic -Drum Driven ................................................ front + rear front + rear (Series) -BrakesService brake .............................................. hydrostatic hydrostatic hydrostaticParking brake .............................................. SAHR SAHR SAHRSteeringSteering system .......................................... ----------------oscillating, articulating----------------------------Steering method .......................................... hydrostatic hydrostatic hydrostaticSteering angle ±...............................degrees 31 31 30Oscillating angle ± ..........................degrees 6 6 7Vibratory systemVibrating drum ............................................ front + rear front front + rearDrive system ................................................ hydrostatic hydrostatic hydrostaticFrequency......................................vpm (Hz) 3600 (60) 3900 (65) 3300/4200 (55/70)Amplitude........................................in (mm) 0.020 (0.5) 0.020 (0.5) 0.020 (0.5)Centrifugal force (each drum) ........lbs (kN) 3600 (16) 3150 (14) 5175 /8550 (23/38)Water Spray SystemType of water spray system ........................ pressurized gravity pressurizedCapacitiesFuel ....................................................gal (l) 6.1 (23) 9 (34) 10.6 (40)Water ..................................................gal (l) 26.4 (100) 50 (189) 58.1 (220)

Standard Equipment

�� Hydrostatic travel and vibration drives.

�� Bolt-on oscillating/articulation joint.�� Hydrostatic articulated steering.�� Spring-Applied, Hydraulically-

Released (SAHR) parking brakes on each drum.

�� Vibration control in travel lever.�� 2 scrapers per drum.�� Plastic water tank.�� Pressure sprinkler system with

interval timer.�� Control and warning indicator

lights for:- Engine oil pressure- Battery- Brakes

�� Hour meter / Fuel level indicator.�� Lockable engine cover.�� Vandal protected instrument panel.�� Transport lifting points - front,

central and rear.�� Emergency stop button.�� Rear drum vibration lock out.�� Corrosion and weather protected

ignition switch.�� ROPS with seat belt.�� Back-up alarm.

Dimensions in inches (mm)A B C D H H1 H2 K L O S W

BW90AD-2 50.5 37.6 18 22.8 58.3 90.6 9.8 73.3 1.1 0.5 35.4(1282) (956) (458) (580) (1482) (2300) - (250) (1862) (28) (12) (900)

BW900-2 45.0 37.6 18.0 22.0 63.8 92.1 - 14.3 81.9 1.1 0.31 35.4(1143) (956) (458) (560) (1620) (2340) - (363) (2080) (28) (8) (900)

BW100AD-4 68.0 42.4 18.7 27.6 - 70.9 97.4 10 97.4 1.5 0.5 39.4(1728) (1076) (475) (700) - (1800) (2475) (255) (2475) (38) (13) (1000)

113

4

2861

-5-1

0

TRENCH ROLLERS

TECHNICAL DATA BMP851 BMP8500

WeightsBasic weight........................................ lbs. (kg) 3395 (1540) 3583 (1625)Operating weight CECE ......................lbs. (kg) 3413 (1548) 3622 (1643)Average axle load CECE ......................lbs. (kg) 1706 (774) 1811 (822)

DimensionsWorking width ....................................in. (mm) 24.0/33.5 (610/850) 24/33.5 (610/850)

Driving Characteristics (depending on site conditions)Speed (1), forward/ reverse.......... mph (kmph) 0-0.7 (0-1.2) 0-0.8 (0-1.3)Speed (2), forward/reverse ..........mph (kmph) 0-1.7 (0-2.7) 0-1.6 (0-2.5)Max. gradeability without/with vibration ......% 55/45 55/45

Drive Engine manufacturer ........................................ Hatz KubotaType .................................................................. 2G 40 D1005Cooling .............................................................. Air WaterNumber of cylinders ........................................ 2 3Performance ISO 9249 ........................hp (kW) 18.8 (14) 19.4 (14.5)Speed ........................................................rpm 2,800 2,600Fuel.................................................................... diesel dieselDrive System .................................................... hydrostatic hydrostaticDrum Driven...................................................... 4 front and rear

Brakes Service Brake .................................................. hydrostatic hydrostaticParking Brake .................................................... SAHR SAHR

Vibratory SystemVibrating drum .................................................. central vibrator front and rearDrive system .................................................... hydrostatic hydrostaticFrequency ..........................................vpm (Hz) 1920 (32) 2520 (42)Amplitude ..........................................in. (mm) 0.083 (2.1) 0.022/0.044 (0.56/1.12)Centrifugal force ................................lbs. (kN) 18000 (80) 8000/16000 (36/72)

CapacitiesFuel ........................................................gal. (l) 5 (19) 6.3 (24)Hydraulic ................................................gal. (l) 10 (38) -Engine oil ..............................................gal. (l) 0.7 (2.5) -

SteeringSteering System ................................................ - articulatedSteering method................................................ - hydrostaticSteering angle +/- .............................................. - 32º

Dimensions in inches (mm)A D H K L S W W1

BMP851 32.3 19.7 47.2 9.4 69.3 .98 24.0 33.5(820) (500) (1200) (240) (1760) (25) (610) (850)

BMP851 Multi-Purpose Compactor

Standard Equipment BMP851 / BMP8500

�� Articulated steering. (BMP8500)�� Dual function cabled / radio remote

control box.�� Standard dual working widths of 24 and

33.5 inches.�� 1 inch padfoot.�� High centrifugal force and amplitude.�� Infinite speed control.�� Electric start. (BMP851)�� 2 travel speed ranges.�� Spring-Applied, Hydraulically-Released

(SAHR) parking brake.�� Balanced, hinged center lift point.�� Swing out/up covers.�� 2 scrapers per drum.�� Exciter directional change with

manual override. (BMP851)�� Two selectable amplitudes. (BMP8500)�� Double exciter system with direct vibration.

(BMP8500)�� Intelligent Vibration Control (IVC).

(BMP8500)�� Reversing protection bow. (BMP851)�� Diagnostic module with failure codes.

(BMP8500)�� Diesel filter with water separator. (BMP8500)

Dimensions in inches (mm)A D H K L S W W1

BMP8500 39.4 20.5 50.2 8.7 74.7 1.0 24.0 33.5(1000) (520) (1275) (222) (1897) (25) (610) (850)

BMP8500 Multi-Purpose Articulated Compactor

114

815-

4-10

TRENCH ROLLER

115

RT 82-SCVibratory Trench RollerItem Number 0009025

Smart trench rollers for tough compaction applicationsWacker Neuson’s articulated trench rollers feature adual joystick control box for easy steering. This “SmartControl” (SC) system uses an infrared signal with line-of-sight control for added safety. If the operator comeswithin 3.3 feet (1 meter) of the roller’s front or rearsensing eye with the control box, the unit will stop mov-ing and vibrating. A smart machine for any jobsite.

Standard Package includes operator’s manual, parts bookand CE certificate.

Features and Benefits • A patented below the axle exciter in each drum allows for

more efficient transfer of compaction energy to the soil forsuperior compaction results.

• The Engine Control Module (ECM) with diagnostic LEDsmonitors all the engine functions such as oil pressure,radiator fluid level, engine temperature, glow plug, battery,tip angle and air cleaner capacity for easy operation andtroubleshooting.

• Design patented RT rollers feature an easy to open hood

made from a heavy-duty molded material that is extremelydurable, rust-free and virtually dent-free.

• Removable fuel and hydraulic tanks along with hydraulicconnectors located on one side of the unit provide foreasy accessibility and improved overall serviceability.

• These trench rollers are ideally suited for the compactionof sub bases for foundations, roads and parking lots; thesheepsfoot drums and vibration speed also offer optimumcompaction of cohesive soils.

Technical Data

Description Metric Imperial

Operating weight 1.473kg 3,247 lb.Drum diameter 520mm 20.5 in.Drum width 820mm 32 in.Overall size l x w x h 1.855 x 820 x 1.230mm 73 x 32 x 48,5 in.Shipping weight (including packaging) 1.557kg 3,434 lb.Shipping size 2.260 x 890 x 1.385mm 89 x 35 x 54.5 in.Engine Type Lombardini, 3 cylinder liquid-cooled, electric start diesel Displacement 916cm3 56 in.3

Max. power output according to DIN-ISO 3046 15,6kW 21 hp Operating power according to DIN-ISO 3046 13,5kW 18 hp Operating speed 2.600 1/min. 2,600 rpm Fuel consumption 5,6 l/hr. 1.5 US gal./hr.Fuel tank capacity 24 l 6.3 US gal.Vibration frequency 41,7 Hz 2,500 vpm Dynamic (centrifugal) force total 34,2/68,4kN 7,700/15,400 lb.Static linear force per drum 9,6 N/mm 54.6 lb./in.Dynamic linear force per drum (max.) 45,3 N/mm 258 lb./in.Lift: soil up to 75cm up to 29.5 in.Low Speed 20 m/min. 66 ft./min.High Speed - forward only 40 m/min. 131 ft./min.Compacted area 972 m2/hr. 10,560 ft.2/hr.Gradeability without vibration 50 % 50 % Gradeability with vibration 45 % 45 % Turning radius - inside 1,6m 63 in.Infrared wireless battery capacity 8 hr. 8 hr.Battery recharge time 40 40 Max. distance for infrared control 14m 45 ft.

Specifications may change due to continuous product development.

4

3096

-3-1

0

116

HYDROGRASSER

HG-30GX3• 3500 gallon total slurry volume.• 99 HP emissions certified turbo diesel.• All iron ANSI centerline discharge pump

design minimizes maintenance requirements.• Exclusive fiber mulch grinder/blender system offers

fast loading of charged materials.• Anti siphoning fill assembly is standard.

HYDROGRASSERS

HG-20GX3• 2350 gallon total slurry volume.• 99 HP emissions certified turbo diesel.• All iron ANSI centerline discharge pump

design minimizes maintenance requirements.• Exclusive fiber mulch grinder/blender system.• Truck bed or chassis mount options.• Spray bar and hose reel options.• Anti siphoning fill assembly is standard.

HG-15GX3• 1850 gallon total slurry volume.• 66 HP emissions certified diesel.• All iron ANSI centerline discharge

pump design minimizes maintenance requirements.• Exclusive fiber mulch grinder/blender system offers fast loading

of charged materials.• Anti siphoning fill assembly is standard.

HG-13GX3• 1550 gallon total slurry volume.• Dual mixing/blender system.• 33.5 HP EC water cooled diesel engine.• Spray bar and hose reel options.• Truck bed or chassis mount options.• Exclusive fiber mulch grinder.• Anti siphoning fill assembly is standard.• Optional remote fill pump package.

HG-5GX3• 625 gallon total volume.• Variable speed hydraulic blender.• 20 HP air cooled Honda engine.• ANSI style centerline discharge pump.• Standard spray boom discharge.• Anti-siphoning fill assembly.• Truck mount (skid) or trailered versions.

HG-10GX3• 1250 gallon total volume.• Exclusive fiber mulch grinder.• Multi-flow blenders speed charging.• 33.5 HP EC water cooled diesel engine.• Truck bed mount or trailer options.• Spray bar and hose reel options.• Anti siphoning fill assembly is standard.• Optional remote fill pump package.

3096

-1-1

0

117

HYDROGRASSER

HYDROGRASSER FEATURESHYDROGRASSER MODEL 2P 2PA 5H3 5H3A 10GX3 10GX3A 13GX3 15GX3 20GX3 30GX3

CAPACITY

WORKING VOLUME (Water) 200(757 l)

200(757 l)

500(1895 l)

500(1895 l)

1000(3785 l)

1000(3785 l)

1300(4921 l)

1500(5678 l)

2000(7570 l)

3000(11356 l)

TANK VOLUME (Slurry)

250(900 l)

250(900 l)

625(2360 l)

625(2360 l)

1250(4750 l)

1250(4750 l)

1550(5900 l)

1850(7000 l)

2350(8900 l)

3500(13000 l)

GRANULARS (Max) Lbs. (kg)

80(40)

80(40)

800(400)

800(400)

2500(1100)

2500(1100)

3100(1400)

5000(2200)

6500(2900)

10000(4535)

FIBER MULCH (Max) Lbs. (kg)

100(45)

100(45)

250(110)

250(110)

500(200)

500(200)

650(290)

750(340)

1000(453)

1500(700)

EFFECTIVE RANGE

SPRAY BOOM Feet (m) 125 (38) 125 (38) 130 (40) 130 (40) 130 (40) 160 (49) 160 (49) 160 (49)

WITH EXTENSION HOSES*Feet (m)

180(54)

180(54)

250(76)

250(76)

400(121)

400(121)

400(121)

350(106)

350(106)

350(106)

*RATINGS OFFERED WITH OPTIONAL HOSE PACKAGE CARRYING CAPACITIES.

DIMENSIONS

LENGTH WIDTH HEIGHT

4'-2" 2'-9"3'-7"

11' 6'-8"5'-3"

8'-1" 4'-11"6'-7"

15'-0" 6'-10"8'-0"

12'-4" 6'-4"8'-0"

19'-6"7'-2"10'-2"

12'-3"7'-6"7'-10"

14'-6"7'-11"8'-2"

16'-7" 7'-11"8'-1"

18'-10"7'-11"8'-10"

WEIGHT

BASIC UNIT Lbs. (kg)FULLY CHARGED Lbs. (kg)

775(351.5) 2735

(1240.6)

1510(684.9)3470

(1573.9)

1750(793.8)7000

(3175.9)

3500(1587.6)

8500(3855.5)

3500(1587.6)14350

(6509.0)

5500(2494.8)16350

(7560.2)

3800(1723.8)17600

(7983.2)

6000(2723.6)23800

(10795.5)

7000(3175.2)29700

(13471.7)

8500(3855.5)43500

(19731.3)

POWER UNIT

STANDARD ENGINE BRIGGSI/H

BRIGGS I/H

HONDA GX670

HONDA GX670

KUBOTA V1505B1

KUBOTA V1505B1

KUBOTA V1505B1

JOHN DEERE

4024T270JOHN DEERE

5030T270JOHN DEERE

5030T270

HORSEPOWER (kw) 8 (6) 8 (6) 20 (14.9) 20 (14.9) 33.5 (25) 33.5 (25) 33.5 (25) 66 (50.7) 99 (74) 99 (74)

COOLING AIR AIR AIR AIR WATER WATER WATER WATER WATER WATER

PUMP

SIZE 3x3 3x4x7 3x4x8-1/4 4x6x10 4x6x10-7/8 4x6x10-5/8

GPM @ PSI 330 @ 30 250 @ 50 400 @ 70 650 @ 115 650 @ 115 750 @ 115

PARTICAL CLEARANCE 1-1/2" 1-1/8" 1-1/8" 1"

MATERIAL POLY ALL IRON ALL IRON ALL IRON

BEARING LUBRICATION OIL OIL OIL OIL OIL

SEAL MS DMS DMS DMS

FILL ASSEMBLY

ANTI-SIPHONING - Standard 2" 2" 2" 2" 2" 2" 2" 2" 2" 2"

(Air Gap) OPTIONAL 1-1/2" 1-1/2" 1-1/2" 1-1/2" 2" 2" 2" 2" 2" 2"

(Air Gap) OPTIONAL - - - - - - - 3" 3" 3"

MOUNTING SKID TRAILER SKID TRAILER SKID TRAILER SKID SKID SKID SKID

AXLE - SINGLE - SINGLE - TANDEM - - - -

STANDARD BRAKES - ELECTRIC - ELECTRIC - ELECTRIC - - - -

STANDARD HITCH - 2" BALL - LUNETTE - LUNETTE - - - -

TRUCK REQUIREMENTS

RECOMMENDED GVW (Min) 5,000 - 14,000 - 23,000 - 25,000 38,000 44,200 64,000

CAB TO AXLE DIMENSION - - - 72" - 102" 102" 120" 132" 144"

Tongue Weight EMPTY - 210 - 670 - 300 - - - -

Tongue Weight CHARGED - 300 - 1800 - 2700 - - - -

SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE.

4

3096

-2-1

0

118

MULCHERS

POWER MULCHERS

SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE.

POWER MULCHER MODEL TM-JR-H20 TM-35 TM-35X MT-2000 M-65 M-90

CAPACITY

TONS PER HOUR (Tonnes) 1½ to 2 (1.4-1.8) 4 to 5 (4.0-4.5) 5 to 7 (4.5-6.0) 10 (9.1) 20 (18.1)

SEED DISTRIBUTOR OPT 1.4 bu 2 bu. 2 bu. 2 bu. N/A

DISCHARGE RANGE Ft. (m)

STANDARD 35 (11) 60 (18) 65 (20) 85 (26) 100 (30)

W/ EXTENSION HOSES 125+ (38) 150+ (46) 150+ (46) 185+ (46) 200+ (46)

SUCTION 50 (15) 50 (15) 50 (15) - -

DIMENSIONS

LENGTHWIDTHHEIGHT

4'-3" (1.24m)2'-9" (.81m)3'-7" (1.05m)

6'-7" (2.1m)3'-8" (1.12m)

5'-4-1/2" (1.7m)

11'-10" (3.6m)7'-6" (2.4)

7'-2-1/2" (2.2m)

19'-6" (2.34m)7'-6" (2.4)

7'-2-1/2"* (2.2m)

11'-10" (3.6m)7'-11-1/2" (2.4)7'-2-1/2" (2.2m)

18'-3" (5.6m)6'-10" (2.1)

8'-10" (2.7m)* TM-35 INSTL

WEIGHT

STANDARD Lbs. (kg) 425 (193) 1200 (544) 1850 (839) 2700 (1225) 2400 (1090) 4400 (1995)

POWER UNIT

GASOLINE HONDA V-20 - - - - -

HORSEPOWER (Kw) 20 (14.9) - - - - -

COOLING AIR - - - - -

DIESEL -

KUBOTAV1505B1

KUBOTAV1505B1

KUBOTAV2403MT

DEERE4045H

HORSEPOWER (Kw) - 33.5 (25) 33.5 (25) 56 (41.8) 115 (85.7)

COOLING - WATER WATER WATER WATER

TM-JR-H20• 20 HP direct drive engine.• 120 bales per hour rating.• 35 ft. direct discharge in still air.• Discharge and suction hose options.• Dry granular broadcast option.• Optional FMVSS trailer adds versatility.• Exclusive two-year warranty.

TM-35• 33.5 HP EC diesel engine package.• 5 ton per hour mulch output.• Discharge 60 ft. in still air.• Discharge and suction hose options.• Dry granular broadcast option.• Exclusive two-year warranty.

MOUNTING SKID SKID TRAILER TRAILER TRAILER TRAILER

STANDARD AXLE - - SINGLE TANDEM SINGLE SINGLE

RATING (Per Axle) Lbs. - - 3500 3500 5200 5200

STANDARD BRAKE - - - ELECTRIC - -

STANDARD HITCH - - 2"BALL LUNETTE LUNETTE LUNETTE

MT-2000• Combination TM-35 power

mulcher and material trailer.• 14 ft. work deck area carries

up to 1 ton of material.• Discharge 65 ft. in still air.• Removable forward rail facilitates

material loading.• Heavy-duty tandem trailer package.• Exclusive two-year power

mulcher warranty.

M-65• 56 HP direct drive water cooled diesel.• Rated 10 tons per hour mulch output.• 85 ft. direct discharge in still air.• Discharge hose placement option.• FMVSS standards heavy-duty trailer.• Optional brake and hitch configurations.• Skid mount version minimizes

vehicle requirements.• Exclusive two-year warranty.

M-90• 115 HP direct drive turbo diesel.• Rated 20 tons per hour

mulch output.• Discharge up to

100 ft. in still air.• Automatic

bale segmenting.• Variable speed

hydraulic feed system.

• Exclusive two-year warranty.

LEVELS / TRANSITSDavid White

L6-20N Meridian Level • 22X Level-Transit

• 1/4-in.(6mm) at 100-ft.(30m) leveling accuracy

• Up to 200-ft.(60m) range

• Horizontal circle

• Lock and tangent screw

• Versatile- ideal for leveling foundations, driveways, patios, floors,sills, for grading streets, curbs, ditches; for alinging fences; or anyother light construction job

• Built-in sunshade- for clear sightings

LT6-900N Meridian Level-Transit A rugged instrument that handles horizontal and vertical work with ease and accuracy.• 22X Level-Transit

• 1/4-in.(6mm) at 100-ft.(30m) leveling accuracy


• Horizontal circle

• Lock level

• Vertical arc

• Clamp and tangent screws

• Ruggedly built and time-proven, handles both horizontal and verti-cal light construction jobs

LT8-300LP Universal Level-Transit • 26X Level-Transit

• ±3/16-in.(4.75mm) at 150-ft.(45m) leveling accuracy


• Horizontal circle, lock and tangent

• Vertical arc, lock and tangent

• 1:100 stadia with glass reticle

• Laser Plummet– Class 2M

LT8-300LTP Line Transfer Unit The LT8-300LTU with 360° telescope rotation allows you to see directly below the instrument for pipe laying applications.• 26X Level-Transit

• ±3/16-in.(4.75mm) at 150-ft.(45m) leveling accuracy

• Horizontal circle, lock and tangent

• Vertical arc, lock and tangent

• 1:100 stadia with glass reticle

• Laser plummet– Class 2M

DWT-10 Electronic DigitalTransite/Theodolite

• 30X Magnification

• 1/16-in.(1.5mm) at 100-ft.(30m) leveling accuracy

• Up to 400-ft.(120m)

• 5-second vertical and horizontal angular readout

• Dual LCD display

• Vertical angle measuring

• Optical plummet

• Zero resetting

• Built-in battery pack

1910

-13-

05

119

4

1151

-3-1

0

PIPE LASER

SANITARY & STORM SEWERS • PIPE JACKING • TUNNELING

GRADELIGHTSelf-Leveling Range +45% to -15%Grade Range +40% to -10%Grade Entry Rolling counter or digit selectGrade Display 0.001%Azimuth Range Total range: 20 ft. at 100 ft./ (6m at 30m)Accuracy ± 1/16" at 100'

(±5mm at 100m; ±10 sec.; ±.005%)

Cross Axis Leveling ManualBeam Type/Output Visible laser diode, 635nm, < 5mW, Class 3REnvironmental IP68; nitrogen purgedPower Supply 1) Rechargeable lithium ion battery pack

2) 110/230V AC converter (charge and runsimultaneously)

3) Spare battery compartment for 4 “D” alkaline batteries

4) Optional 12V power cord

Battery Life @ 32ºF/0ºC 40 hrs. Li-ion battery; 50 hrs. alkalineCharging Time 5 hrs. maximumMounting 5/8 x 11 (female mounting thread)Operating Temperature -4º to 122ºF (-20º to +50ºC)Storage Temperature -4º to 140ºF (-20º to +60ºC)Size Diameter: 5.5" (140mm),

Length: <10.5" (265mm)Weight 7.6 lbs. (3.5kg) with alkaline batteryWarranty 1 year (2/3 year optional warranties)REMOTE CONTROLOperating Range 600' (190m) front (through the pipe);

25' (7.6m) from rearbatteries 3 AA alkalineBattery LIfe 2,000 hrs. (1 year)Dimensions 4.7" x 2.35" x 1.2" (119 x 60 x 30mm)

Easy AligmentHigh Visibility LED Line Pivot Point is a fast reference for centering.Easily seen from outside the manhole.

Grade Reference Pointson both sides make it easyto set elevation.

Remote Control(Optional with Above Ground Package)Moves the beam left or right for line and putsthe laser in standby or locked modes.Press to quickly re-center adjustment range.

Large Display is Viewable from Outside Most Manholes• Line Indicator show the beam position relative to the adjustment range.• Status at-a-glance shows self-leveling staus, battery indicator,

electronic level vial showing cross axis level position and lock status of laser and remoter.

• Unique Dual Color Grade Display Color changes to denote Positive or Negative Grade (to .001% increments) to minimize costly input errors.

Set Up... The Way You Work

• In The Pipe

• Above Ground

• Open Cut

• Tight Pre-poured Inverts or

Small Manholes

• Flat Bottom Manholes

• Drop Manholes

SIMPLE Up +% Down -%

Left � Right � Operation• Enter Grade with a Rolling Counter or Digit Select Method

Press and hold a grade button for a few moments. Afterrelease, it will automatically increase (or decrease) until youpress the key again to stop. Grade can also be entered byselecting the digits using the ENT key.

• Press +% -% to reset to zero grade.

• Press � � to reset line adjust range.

GradeLight2700

120

EAGL 3000S, 2000, 1-Touch

1151

-6-1

0

LASER LEVELS

The EAGL H features:

• Brushless Motor Design that reduces wear and tear on the laser providing for longer product life, as well as providing unparalleled battery life of up to 160 hrs. on 2 standard flashlight batteries.

• Accuracy of ±3/32" @ 100 ft. and a working range of 1000 ft. in diameter.

• Dual Manual Grade of ± 10% in both the X and Y direction.

• The H.I. Alert system protects against erroneous reading by shutting down the laser and warning the user that the instrument has been moved from its original position.

System includes: EAGL H Laser,LS100 Detector, Alkaline Battery Tray,NiCad Battery, Charger, Manual andCarrying Case.

EAGL Laser LevelsHighly accurate instruments for today’s tight job requirements....and tough, easy-to-use construction tools

Applications:

• Establishing elevation and grade stakes.• Setting concrete forms and footings.• Sub base leveling.• Wet screeding concrete.• Excavating for foundations, footings, drain lines and

septic systems.• Machine control and topography applications.• Basically ALL Leveling applications.

EAGL H

SPECIFICATIONS

All EAGL modelshave a visible redbeam; rotationspeed is 600 rpm EAGL 3000S EAGL 2000 EAGL 1-Touch

Accuracy Better than 1/16" in 100 ft.± 4mm/100m; ± 8 arc secs.

Range (diameter) 3,000 ft. (900m) 2,000 ft. (600m) 1,500 ft. (450m)Horizontal Self-Leveling Range ± 7% (± 4º)Battery Life 100 hrs.

w/(4) “D” alkaline batteries:40 hrs. w/optional rechargeable pack

Matching Slope ± 6% manual slope in X axis;y axis is self-leveling

Hi Alert X X –Windy Mode X X –Operating Temperatures -4º to 122ºF (-20º to 66ºC)Environmental IP55 water and dust resistantSize 8" H x 6.5" W x 6" D

(20 x 16 c 15cm);5 lbs. (2.3kg)

Warranty 2 year drop 2 year 1 yearDetector / Rod Clamp Included LS100 LS100 LS50(rod and tripod sold separately)

SPECIFICATIONSWorking Range 1000 ft. with LS100 DetectorAccuracy ± 3/32" @ 100 ft.Self Leveling Range 0% (5.7 degrees)Grade Matching Yes, ± 10% in both X and Y AxisLaser Diode <5mW, Class 3R, 635nmPower 2 D-Cell and NiCad RechargeableBattery Life D-Cell: 120 hrs., NiCad: 40 hrs.Rotation Speeds 0, 90, 600 RPMBrushless Motor Design YesEnvironmental IP54 for water and dust resistance

121

4

1151

-8-1

0

CONSTRUCTION LASERS

EZ Dig ProThe EZ Dig Pro provides precise grade control for digging a fixed depth or a slope, without the expense of another person in the excavation to check depth. The machine stays productive! The calibrated system ensures consistent and accurate grade readings, saving time and money by reducing over-cutting. If you’ve been checking grade with a laser or optical instrument and grade rod, using this system will keep the machine and operator fully productive. If you’ve been using a machine-mounted laser receiver, there’s no need to stop digging to place the bucket and dipper stick in the same vertically plumb position each time you want an accurate reading.

Features:

• The EZ Dig Pro can be installed and calibrated in 45 minutes or less using its patent-pending software.

• Sensors are wireless; no cables at the pivot points.• No welding or wrenches needed.• Sensor solar panels maintain the charge of the built-in batteries

automatically throughout the day.• Strong rare earth magnets hold securely.• Displays Real-Time Depth throughout the whole digging process.

EZ DIG PRO SPECIFICATIONS

Accuracy ± 3/8" (1cm)

Slope Capability ± 300%

Environmental Sensor IP68; control box & display: IP64

Operating Temperature -4° to 158° F (-20° to +70° C)

Storage Temperature -22° to 176° F (-30° to +80° C)

Warranty: 1 year

GradoPlane 25Automatic Dual Grade Laser

Advanced Performance, Yet Easy and Efficient to Use

Fast Automatic Self-LevelingThe GradoPlane 25 levels up fast, even when inputting the maximum 25% grade. Saves time, especially when multiplegrade breaks are needed or when matching an existing slope.

Simple to Use, Even for Advanced FunctionsAfter turning the unit on, there are just four buttons that controlall laser functions. Easy, intuitive screen selections allow you toquickly set advanced functions or change the laser setup.

Two-Way Remote Speeds Setup and OperationMake grade changes from anywhere on the jobsite using thefull-function RF remote. Savestime when you’re balancing thepad -- use the wireless remote toadjust the laser’s grade from thecab and quickly finish the job.

• LCD display and grade andenter buttons are the same ason the laser.

• Automatic shut-off conservesbattery power.

• Can select backlit display.

GRADOPLANE 25 SPECIFICATIONS

Operating Range 2,500 ft. (750m) diameterSelf-leveling Accuracy ± 1/16" at 100 ft. (1.5mm at 30m, 10 arc secs.)Self-leveling Range ± 5° (also manual mode for special applications)Grade Capability -5 to +25% in either axis; (-5 to +15% in both axes)Rotation Speeds 300, 600, 900 and 1,200 rpmLaser Diode Infrared 780nm invisible, Class 1Battery Type “D” alkaline or NiMH rechargeableBattery Life 8 alkaline — Up to 130 hrs.

2 NiMH Packs —Up to 100 hrs.Operating Temperature -4° to 122°F (-20° to 50°C)Environmental Waterproof to IPX-7 standardDimensions 10.4" x 10.2" x 8" (265 x 260 x 200mm)Weight 11 Ibs. (5kg) without batteriesWarranty One year

REMOTE CONTROL SPECIFICATIONSDistance 200 ft. (60m) typicalBattery Type Four AAA alkalineSize 6" x 2.8" x 1.8" (155 x 70 x 45 mm); 14 oz. (410g)

GradoPlane 25 laser package includes:

• LS100 detector • Remote• 1 rechargeable battery pack • AC charger

Package also available without remote.Optional accessories: alignment scope,12V power cableand additional rechargeable battery pack.

Package Includes:1. Control box2. In-cab display 3. Pointer laser for

calibration setup4. 3 angle sensors

(one with a laser receiver)

5. 3 mounting plates (use is optional)

6. Removal tool for magnetically-attached sensors

7. Charger, to supplement solar charging

8. Option: 4th sensor for dual boom excavator or chassis

122

1151

-7-1

0

LASER ROD / BEAM DETECTOR

SmartRod• All-in-one: laser receiver, grade rod, digital measuring tape• Automatically calculates cut-and-fill• Makes work quicker and easier

Beam reception• Caption window is so much larger!

6.5" on the SmartRod vs. 2.5" on astandard detector (16.5cm vs. 6cm).

• Linear Receiving Technology (LRT):the beam only has to touch somepart of the window; it does not needto be in the center.SmartRod finds the center.It’s easy to find the beam, even down in a trench where you can’t see the laser!

Modes• Elevation reading.• Cut and fill.• Tape measure mode: measure

interior heights without a laser.

* At short range, below 3m, high output lasers can cause inconsistent readings. Please restrict use of SmartRod in short range.

** Depends on laser and distance

SPECIFICATIONSRange* ** >9'-10"/3m to working range of laserAccuracy ±3/32" / ±2.5mmRange of reading Elevations from 3.3 ft. to 13.2 ft. /1m to 4mUnits • Feet/10ths/100ths

• Feet/inches/16ths • MetricBeam capture angle 120° minimumLaser detection window 6.5" / 165mmDetectable laser beam 610nm to 780nmBattery life Control panel: 3 x AA, min 60 hrs.

Receiver: 3 x AA, min 3,000 measurementsStandby of capture mode 30 secondsAutomatic shut-off 5 minutesOperating temperature 14°F to 122°F / -10°C to + 50°CIP protection IP54Weight 8 lbs. / 3.6kgWarranty 1 year

Applications:• Checking elevations.• Cut-and-fill measurements.• Working to a fixed reference,

as for setting forms.• Creating benchmarks and offsets.• Height or length measurements

(electronic tape measure mode).

LS100 – Detector and Rod Clamp• Convenient front and rear displays.• Deadband choices: fine, medium, wide.• Display channels: 11 on LCD; 5 on LED.• LEDs for use in low light or above eye level,

or for long range jobs like slope match.• Bubble vial on clamp to plumb rod• Clamp also fits round or oval rods.

123

4

HB Series required with Gehl Dynacarrier, JCB QFit and Pettibone

1022

-5-1

0

SKID-STEER ANDFORKLIFT BUCKETS

HEAVY-DUTY SKID-STEER BUCKETS

“SLIP ON THE FORKS” FORKLIFT BUCKETS

QUICK-TACH FORKLIFT BUCKETSQuick-Tach bucket replaces forks and carriage.

SELF-DUMP BUCKETS(Turns a straight-mast forklift into a loader) Universal fit – “slip on the forks”

Model 1460 60" wide 0.8 cu. yd. capacityModel 1472 72" wide 1.0 cu. yd. capacityModel 1496 96" wide 1.25 cu. yd. capacityModel 1460HB 60" wide 1.0 cu. yd. capacityModel 1472HB 72" wide 1.25 cu. yd. capacityModel 1496HB 96" wide 1.65 cu. yd. capacityModel 1496HC 96" wide 2.0 cu. yd. capacity

All buckets available with bolt-onblade for longer life.

Increases bucket life up to 3 times or longer.

Model 1400B 60" wide 1.0 cu. yd. capacityModel 1406B 72" wide 1.2 cu. yd. capacityModel 1408B 95" wide 1.6 cu. yd. capacityModel 1408BHC 95" wide 2.0 cu. yd. capacity

MANUAL DUMP BUCKETSModel Width Capacity Weight1440SD 45" ID 0.25 cu. yd. 420 lbs.1445SD 45" ID 0.50 cu. yd. 445 lbs. 1472SD 72" ID 0.75 cu. yd. 710 lbs.

HYDRAULIC DUMP BUCKETS1445SDH 45" ID 0.50 cu. yd. 510 lbs. 1472SDH 72" wide 0.75 cu. yd. 710 lbs.

(Fits all extendible-reach forklifts)

Low Profile Utility Fertilizer Snow & Litter Light MaterialDirt

A size and style for every materialLow Profile DirtBucketsDesigned to let yousee the leading edgefrom the operator’sseat for better bucket control.

New Improved Bucket DesignSTRONGER AND BETTER

Star has the skid-steer buckets you need.Options include:

• Bolt-On-Blade.• Large series 23 pin-on teeth welded into bucket.

Built to fit yourspecific make andmodel perfectly

124

1022

-7-1

0

FORKLIFTATTACHMENTS

HANDLE TRASHUse on roof tear-off jobs, renovation projects oranywhere intermediate handling of trash is needed.

Model 1420 3' x 5' x 5' 2.7 cu. yd. cap.Model 1425 4' x 5' x 5' 3.7 cu. yd. cap.Model 1430 4' x 5' x 7' 5.0 cu. yd. cap.

Open in front for easy loading.

Universal fit – “slip on the forks”

Model 1805N 0.5 cu. yd. cap.Model 1810 1.0 cu. yd. cap.Model 1815 1.5 cu. yd. cap.Model 1820 2.0 cu. yd. cap.Model 1825 2.5 cu. yd. cap.

Universal fit – “slip on the forks”

Model 1820

Trash Hoppers

Self-dumping Hoppers

LIFT LONG FLEXIBLE MATERIAL

Model 1150

SPREADER BARS

Model 1150 5-8,000 lbs. cap. extends 8-12'Model 1160 8-16,000 lbs. cap. extends 12-20'Model 1190 9,000 lbs. cap. extends 22-38'Model 1195 15-20,000 lbs. cap. extends 20-30'

Universal fit - “slip on the forks”

Manual Dump

Model 1550 0.5 cu. yd. cap. Model 1575 0.75 cu. yd. cap.

Heavy-duty

CONCRETE HOPPERS

Places concrete in hardto reach areas, groutsmasonry walls. Savesthe cost of renting apump or crane.

EXTEND YOUR REACH

CONCRETE HOPPERS

QUICK-TACH TRUSS BOOMS

Model 1302 2' reach 10,000 lbs. capacityModel 1310 10' reach 2,000 lbs. capacity Model 1320 12' reach 2,000 lbs. capacityModel 1325 Wide 12' reach 2,000 lbs. capacityModel 1330 15' reach 2,000 lbs. capacityModel 1335 Wide 15' reach 2,000 lbs. capacity

Model 1360B 6,000 lbs. cap.

HEAVY-DUTY JIBExtends 7' to 12'

Casters optional

FORK LIFT ATTACHMENTS

Model 1550H 0.5 cu. yd. cap. Model 1575H 0.75 cu. yd. cap.

Hydraulic Dump

125

4

Model Capacity

120 1/2 cu. yd.125 3/4 cu. yd.

1022

-10-

10

SKID-STEER LOADER ATTACHMENTS

SKID-STEER FORKFRAMES with “ITA Style” Captive Forks

Place concrete in hard toreach areas for less cost.

CONCRETE PLACEMENT BUCKETS

Handle trash and loose material efficiently and easily.

Easy as 1, 2, 3:• Scoop up sand and gravel.• Tilt-up – add water and

cement, then mix.• Discharge thru side gate

or top opening.

ITA STYLE ForksITA Style Forks lock into position.Forks are “captive” and can’t swingout when a load of railroad ties orother loose material is dumped offthe end of the forks.

Model 120

Model 151

Model Capacity

151 1.0 cu. yd.152 1.5 cu. yd.153 1.75 cu. yd.

Model Capacity140 9 cu. ft.

SCOOP-N-MIX CONCRETE MIXER TRASH AND LOOSE MATERIAL HOPPERS

TELESCOPING CRANE JIBREACH FARTHER AND LIFT HIGHER

Turns a skid-steer into a mini-crane.

Model 130Telescopes 4'0" to 6'0"1,000 lb. lift capacity

Heavy-Duty Model 110FF-ITA• Extra heavy-duty - Toughest on the market.• Frame constructed of ½" x 3" flat bar.• Machined ITA Ffork carriage bars.• Big 5,500 lb. load capacity.

Economy Model 110EC-ITA• Economy ForkFrame.• “Clear View” of forks.• 3,700 lb. load capacity.• Good quality for low cost.• Weight 157 lbs.

Model (frame) Description Capacity Weight

110FF-ITA Heavy-duty - “ITA Style” forkframe 5,500 lbs. 232 lbs.110EC-ITA Economy - “ITA Style” forkframe 3,700 lbs. 157 lbs.Model (forks) Style Fork Dimension Capacity WeightF138x4x42CL2 Pallet 1-3/8" x 4" x 42" (set of 2) 3,700 lbs. 176 lbs.F138x4x48CL2 Pallet 1-3/8" x 4" x 48" (set of 2) 3,700 lbs. 194 lbs.F15x4x48CL2 Pallet 1-1/2" x 4" x 48" (set of 2) 5,500 lbs. 214 lbs.

MIX-N-PLACE • Mixer type -

rotating drum.• Hyd. requirements –

8 to 10 gpm.• Capacity - 6 cu. ft.• Empty weight -

298 lbs.

Model 135

126

127

GeneratorsMeasuring WheelsPressure Washers

Steam CleanersSubmersible Pumps

VacuumsAir Compressors

Tool BoxesTrash Pumps

Ventilation BlowersHopper Brooms

ScaffoldingForklift Platforms

SlingsPortable Light Towers

HeatersLifts

BoomsMessage Signs & Arrow Panels

LevelsHand Tools

WheelbarrowsSafety Glasses

Site Management 5

TPG3-4500HDXPowered by an 8 hp HondaOHV engine with low level oilalert system.

Automatic Idle Control.

Recoil Start. Large air filter for emissions control.

4.5 gallon fuel tank.

Rated load run time 8.5hours/half-load 14.2 hours

Noise level on a rated load is 68dB.

TPG3-3000HDXPowered by a 5.5 hp HondaOHV engine with low level oilalert system.

Recoil start. Large air filterfor emissions control.


Rated load run time 14.6hours/half-load 22 hours.


Automatic Idle Control not available on TPG3-3000HDX.

TPG3-6000HDXPowered by an 11 hp HondaOHV engine with low level oilalert system.


Rubber Vibration Pads isolatethe generator/engine setreducing vibration.

A large silent muffler withspark arrestor greatlyreduces noise.

Easy recoil start. Large air filter for emissions control.


Rated load run time 5.7hours/half-load 8.5 hours.


TPG3-7000HDX/HDXEAvailable in electric start* orrecoil start.

Powered by a 13 hp HondaOHV engine with low level oilalert system.




Large air filter for superioremissions control.

4.5 gallon fuel tank with fuel gauge.

Rated load run time 5.3hours/half-load 8.1 hours.


*Battery not included.

*Wheel kit and lifting bail are optional.

TPG-11000HDXEPowered by a 18 hp HondaOHV engine with low level oilalert system.




Large air filter for superioremissions control.



*Battery not included.

*Wheel kit is optional.

710-

4-10

128

GENERATORS

TPG-series generators are designed to withstand the severe conditions of construction jobsites orindustrial applications, especially where extra durability and dependable, stable power are required.

Ideal to supply the power to Tsurumi’s single-phase submersible pumps and all your electrical powertools such as drills, saws, lighting and heaters.

TPG3-4500HDX

TPG3-3000HDX

TPG3-6000HDX

TPG3-7000HDXETPG3-7000HDX

TPG-11000HDXE

Model Max/Rated

Current Voltage Engine ModelMax

HP/RPM Fuel TankCapacity

RunningTime

StartingSystem

Noise Level Weight lbs.

TPG3-4500HDX 4500/3600 120/240 Honda GX240U1EDT6 8.0/3600 6.6 12.5 Recoil 68dB 164 TPG3-3000HDX 2900/2400 120 Honda GX160U1VES6 5.5/3600 4.2 12.1 Recoil 64dB 110 TPG3-6000HDX 6000/5000 120/240 Honda GX340U1EDT6 11.0/3600 6.6 8.5 Recoil 72dB 186

TPG3-7000HDX(E) 7000/6000 120/240 Honda GX390U1EDT6 13.0/3600 6.6 7.6 Recoil/Electric 78dB 194/211 (Electric)TPG-11000HDXE 10500/9500 120/240 Honda GX620 18.1/3600 9.75 10.5 Recoil/Electric 75dB 423

PowerPro™ 25 PowerPro™ 45 PowerPro™ 65 PowerPro™ 100

541-

1-10

129

TOWABLE GENERATORS

GENERATOR SPECIFICATIONSGenerator Type Taiyo Taiyo Taiyo Taiyo

Armature Connection Star with Neutral/Zig Zag Star with Neutral/Zig Zag Star with Neutral/Zig Zag Star with Neutral/Zig Zag

Number of Poles 4-Pole 4-Pole 4-Pole 4-Pole

Insulation Class F Class F Class F Class F

Excitation Brushless with AVR Brushless with AVR Brushless with AVR Brushless with AVR

Voltage Regulation 0.5% 0.5% 0.5% 0.5%

Power Factor 0.8 0.8 0.8 0.8

Frequency 60 HZ 60 HZ 60 HZ 60 HZ

Standby Power 27.5kVA / 22kW 48.5kVA / 38.8kW 67kVA / 53.6kW 110kVA / 88kW

Prime Power 25kVA / 20kW 45kVA / 36kW 63kVA / 50kW 100kVA / 80kW

Voltage Single Phase 120V / 240V / 277V (Switchable) 120V / 240V / 277V (Switchable) 120V / 240V / 277V (Switchable) 120V / 240V / 277V (Switchable)

Voltage Three Phase 208V / 240V / 416V / 480V (Switchable) 208V / 240V / 416V / 480V (Switchable) 208V / 240V / 416V / 480V (Switchable) 208V / 240V / 416V / 480V (Switchable)

AMPERAGESingle Phase 120V / 240V 60 Amps (L1-N & L3-N) / 60 Amps 108 Amps (L1-N & L3-N) / 108 Amps 152 Amps (L1-N & L3-N) / 152 Amps 242 Amps (L1-N & L3-N) / 242 Amps

Three Phase 208V / 240V / 480V 65 Amps / 60 Amps / 30 Amps 119 Amps / 108 Amps / 54 Amps 167 Amps / 152 Amps / 76 Amps 264 Amps / 242 Amps / 120 Amps

ENGINE SPECIFICATIONSEngine Isuzu 4LE1, 4-cycle, water-cooled

swirl chambersIsuzu 4JJ1T, 4-cycle, water-cooled directinjection turbocharged

Isuzu 4JJ1X, 4-cycle, water-cooleddirect injection turbocharged intercooler

Isuzu 4HK1X, 4-cycle, water-cooled directinjection turbocharged intercooler

Number of Cylinders 4 4 4 4

EPA Emission Level Interim Tier 4 Interim Tier 4 Tier 3 Tier 3

Output @ Rated Speed (1800 rpm) 31.5 HP 57.0 HP 97.8 HP 152 HP

Governor Type Mechanical Electronic Electronic Electronic

Integral Fuel Tank Capacity 50 gallons 106 gallons 106 gallons 198 gallons

Fluid Containment 110% 110% 110% 110%

Lubricating Oil Capacity 2.1 gallon 4.0 gallon 4.0 gallon 5.4 gallon

Coolant Capacity 1.6 gallon 2.7 gallon 2.9 gallon 5.7 gallon

Battery 12V x1 12V System 12V x1 12V System 12V x1 12V System 12V x1 12V System

FUEL CONSUMPTIONFull / 75% / 50% Load 1.7 / 1.3 / 1 gal./hr. 2.6 / 2.1 / 1.5 gal./hr. 3.6 / 2.8 / 2 gal./hr. 5.9 / 4.7 / 3.2 gal./hr.

Run Time @ Full Load 29.4 hrs. 40.8 hrs. 29.4 hrs. 33.6 hrs.

WEIGHTS AND DIMENSIONSL x W x H wo/Trailer 67" x 28" x 50" 82" x 39" x 61" 82" x 39" x 61" 100" x 46" x 72"

Operating Weight (Wet) 1962 lbs. (890kg) 3530 lbs. (1600kg) 3660 lbs. (1660kg) 6063 lbs. (2750kg)

LYNXRITE TRAILERSL x W x H**** 119" x 54" x 62" 144" x 70" x 73" 144" x 70" x 73" 196" x 79" x 85"

Weight 625 lbs. (284kg) 1225 lbs. (556kg) 1225 lbs. (556kg) 1650 lbs. (748kg)

Note: SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE.****Height (H) is calculated from ground level to the top of the generator.

Mobile power that’s Tough..... Yet Quiet

5

2362

-5-1

0

130

LEVELS

ALWAYS TRUST – NEVER ADJUST™STABILA levels represent the perfect balance of accuracy and durability, technology and crafts-manship. For over a century, quality tradesmenhave trusted STABILA to be accurate 100% of the time.

TYPE 196

TYPE 96M

HEAVY-DUTY MAGNETIC LEVEL TYPE 96M• Strongest magnets, flush mounted –

Work hands-free.• Spring steel hairline indicators inside

the vials.• Certified level accuracy in top read position:

1/32" over 72".• Levels 59" and longer have a bridge over

the horizontal vial for uninterrupted scribingand increased frame strength.

• Patented, epoxy-locked vials never need adjusting.

• Removable rubber end caps for flush measuring in corners.

• Patented red pads on end caps grip wallsand flat surfaces. Prevents slipping on walls.

• Level accuracy guaranteed for life; vials willnever fog, leak or require adjustment.

• Readable in every direction with no changein accuracy tolerance.

HEAVY-DUTY LEVEL TYPE 196• Crystal clear vials readable in any

direction with no change in accuracy tolerance.

• Spring steel hairline indicators in vials.• Best frame strength-to-weight ratio.• Removable rubber end caps for scribing

in corners and for reading tight header and sill openings.

• Rubber end caps grip walls and do not leave marks.

• Metal hang hole for storing level on site.• Large comfortable rubber hand holes.• Fast and accurate installations.• Strong, wide frame.• Vials are guaranteed for life.

BENT LEVELS VOID WARRANTY.

PLATE LEVEL 2 TYPE 106T• Strong re-enforced frame.• Fully sealed solid rail (six

sided) extension eliminatesdeflection, and delivers the smoothest extensionmovement available.

• Removable 1-5/8" stand-offs reach around braces.

• Top plumb vial is permanently positioned at eye level.

• Frame side opposite the stand-offs is a level measuring surface andstraight edge.

• Scale on both sides of extension for FAST set-ups:8'-1", 9'-1", 10'-1", etc.

• Vials are guaranteed for life never to fog, leak orrequire adjustment.

• Certified accuracy in thetop read position: 1/32" over 72".

MASON’S LEVELTYPE 196K• Light weight and

strong frame.• Special plumb vial locations

to put the bubble in front ofyour eyes no matter whichcourse you are on.

• Wide open plumb vials for maximum visibility.

• Strike Zones – Blow shieldsare designed to be hit with a trowel.

• Centered hand holes (on 36" and 48" levels) for one-handed balance.

• Wide open horizontal vial – Less bending over, betterfor your body.

• Easy to clean vials andframe – smooth design forremoval of mortar.

• Removable and replaceable rubber end caps.

ELECTRONIC MAGNETIC TECH LEVEL TYPE 196-EM• Strongest rare

earth magnets – Work hands-free.

• Two displays – Top and side.

• 5 Construction languages – Units of Measure:

DegreesPercentagemm/MIn./Ft. in decimalIn./Ft. fractional

• Tone out – Level, plumb or any angle.

• Easy to calibrate.

TYPE 196K

TYPE 196-EM

Type 106T

1910

-15-

10

MEASURING WHEELS

MM-12 SERIESThis precision molded one-foot circumference wheel is designed for measuring on a smooth, hard surface. The MM-12 features a 5-digit, push button reset counter and a retractable twist-and-lock handle.

FEATURES / BENEFITS:• Lightweight and compact / Fits in a briefcase; easy to carry. • Wide, precision molded tire, stable grip on smooth, hard surfaces.• Molded polycarbonate 5-digit counter, records to 10,000 ft. or

1,000 meters with convenient push-button reset. • Safety-Green color, easy to locate at home or at the job site. • Telescoping handle / compactibility.

MM-12 TWIN SERIESThis dual precision molded one-foot circumferencewheel offers increased stability and accuracy whenmeasuring on a smooth, hard surface. The MM-12 Twin features a 5-digit, push button reset counterand a retractable twist-and-lock handle.

FEATURES / BENEFITS:• Dual wheel configuration, superb traction and stable control.• Wide, precision molded tires, firm, stable grip on smooth,

hard surfaces.• Molded polycarbonate 5-digit counter, records to 10,000 ft.

or 10,000 meters with convenient push-button reset.• Safety-Green color, easy to locate at home or

at the job site.• Brass axle bushings, free-spinning wheels

for easy rolling.• 3-piece telescoping handle compactibility.

MM-30 SERIESA money saving workhorse is the best way to describe the MM-30. From appraising, landscaping and construc-tion to fencing the MM-30 can easily handle the job. The MM-30 features a 5-digit, push button counter, a steel wheel, and a convenient flip up stand.

FEATURES / BENEFITS: • Silver powder coat steel wheel, lasting durability

and good looks.• Brass axle bushings, free-spinning wheel for easy rolling.• Molded polycarbonate 5-digit counter, records to

10,000 ft. or 10,000 meters with convenient push-button reset.

• Safety-Green color, high visibility means a safer work environment.

• 3-foot / 1-meter circumference, best all-around versatility.

• Insert-and-Lock handle, transport and storage is easy with the unique,Insert-and-Lock handle.

• Wheel stand keeps wheel upright when not in use.

ROLATAPE® PROFESSIONAL SERIES300 SERIESStandards of versatility and portability are set by the Rolatape® 300 Series. Real estate, landscaping, municipal and construction measuring needs are handled with ease by the 300 Series. Professionals rely on the smooth rolling, accurate 300 Series to perform on pavement, dirt and rough surfaces. Transport and storage is easy with the unique, Insert-and-Lock handle.

FEATURES / BENEFITS: • All steel construction, heavy-duty strength

and durability.• 5-digit ratchet counter measures up to 100,000 ft.,

yards or meters with convenient reset knob.• Calibrated wide rubber wheel, accurately measures

a wide variety of terrain including paved and unpaved surfaces.

• Safety-Glo color, easy to find in vehicle and on job site.

• Insert-and-Lock handle Transport and storageis easy with the unique, Insert-and-Lock handle.

• Available with or without stand, keeps wheel upright when not in use.

400 SeriesThe Rolatape® 400 is a tough, all purpose measuring wheel for heavy construction, utilities, cable, telecommunications, land surveying and other critical measuring applications. The 400 is the world’s #1 selling industrial measuring wheel,which features an automatic brake/mud scraper and a stand.

FEATURES / BENEFITS:• All steel construction, heavy-duty

strength and durability.• 5-digit counter.ª Records up to 100,000 ft. or

meters with convenient reset knob (Dual counters available).

• 4-foot circumference wheel.• Easier to measure accurately on

rough terrain.• Wheel stand keeps wheel upright when

not in use.• Wheel brake.• Transport to second site without losing existing measurement.

5

131

535-

6-10

PRESSURE WASHERS

COLD WATER PRESSURE WASHERSJCW SERIESPortable Gas Driven

MODEL JCW-3504-OMHB JCW-3504-OMRB JCW-3004-OMHBOperating Pressure (PSI) 3500 3500 3000Discharge Capacity (GPM) 3.7 3.7 3.5Engine Honda OHV Subaru OHV Honda OHVDisplacement 389cc 404cc 389ccDimension (LxWxH) 39.5x28.5x26 39.5x28.5x26 39.5x28.5x26Shipping Weight 245 245 243Net Weight 191 191 189

SPECIFICATIONS

JCW-3004-OMHB

JCW-3504-OMHB

These cold water pressure washers have beenspecifically designed for heavy-duty cleaning jobs,degreasing equipment, cleaning caked-on mud fromtools and removing dried cement from forms. Thesedurable pressure washers feature rugged compo-nents designed to keep them up and running, evenunder the most extreme conditions.

FEATURES:• Quick connect nozzles (0º, 15º, 25º and 40º).• Water filter with clear sleeve for screen inspection.• Professional grade insulated trigger gun with

safety lock-off.• Thermal relief valve.• 3500 psi models have a 48 inch lance and 3000 psi

models have a 36 inch lance.• Two-piece belt guard with 1/4-turn release for quick

access to belts.• Performance-proven engine with low-oil protection. • Belt drive triplex piston AR pump with

ceramic plungers. • Adjustable pressure. • Solid steel threaded axle for added strength.• Dual rubber isolators.• 50-foot x 3/8 inch non-marking hose with quick

connects, swivel and bend restrictors.• Stainless steel and brass unloader.• Dual cogged belt drive system to prevent slippage.• 1-1/4 inch powder coated steel tube handles.• Powder coated steel base plate with welded

reinforcement for reduced vibration.• Convenient hose wrap.• Gun/wand holder for convenient storage.• Pneumatic tires with tubes for longer life.

132

535-

7-10

PRESSURE WASHERS

COLD WATER PRESSURE WASHERSJCW SERIESPortable Gas Driven

MODEL JCW-3003-OMHB JCW-3003-OMRBOperating Pressure (PSI) 3000 3000Discharge Capacity (GPM) 3.0 3.0Engine Honda OHV Subaru OHCDisplacement 270cc 265ccDimension (LxWxH) 39.5x28.5x26 39.5x28.5x26Shipping Weight 232 232Net Weight 178 178

SPECIFICATIONS

JCW-3003-OMHB

Water filter withclear sleeve for screen inspection

Two-piece belt guardwith 1/4-turn releasefor quick access to belts

Solid steel threaded axle foradded strength

Dual cogged belt drive system to prevent slippage

Three (3) year warranty on all Honda and Subaru engines

One (1) year limited parts and labor warranty

Seven (7) year limited warranty on pump

Options available on Model JCW-3003:

• Insulated dual lance — Has both a high and low pressure tip that allows you to switch to the low pressure chemical injector without having to change tips.

• Low pressure detergent injection — Allowsthe user to apply the recommended detergents.

• High pressure detergent injection — High pressure water mixes with detergent to clean even the heaviest build-up.

• Puncture-proof tires — Tires are flat-free, maintenance free and non-marking, 13-inch, white hub, two tires.

133

5

2397

-2-1

0

PRESSURE WASHERS / STEAM CLEANERS

Unleash the POWER and PERFORMANCE of a SharkSGP-XL SeriesHot Water Pressure Washer• Gasoline Powered• Diesel or Fuel Oil Heated• Direct Drive PumpThe SGP-XL is Shark’s answer to meet thedemand for versatility and portability in a hotwater pressure washer. Mounted on an extra-durable all steel chassis and protected by arugged steel roll cage, the SGP-XL is easy tomove in all terrain with its four 13-inch tubedpneumatic tires. All four SGP-XL models fea-ture the ever-reliable Honda (9-13 HP)engines with low-noise muffler. The SGP-XLalso has a triplex, oil-bath Kächer pump withan enviable limited 7-year warranty and acold-rolled hot water coil. Two of the modelscome with electric start and all deliver cleaning power between 3000 and 3500 PSI.Available with STEAM CLEANING option.

BR SeriesCold Water Pressure Washer• Gasoline Powered• Belt Drive Pump• Roll Cage DesignThe BR is the heaviest-duty workhorse of theShark cold water family with cleaning powerof up to 5000 PSI. Six models are poweredby a variety of industrial-grade engines,including Honda and Vanguard, and all fea-ture a tri-plunger, oil-bath, belt-drive Kächerpump with an unmatched limited 7-year warranty, EZ start valve and an extra ruggedroll cage made of 1¼-inch steel tubing, pro-tected by an epoxy, powder coat finish and alimited lifetime warranty. The BR is alsounique with 13-inch tubed pneumatic tiresfor easy maneuvering in all terrain, and vari-able pressure wand for convenience in alter-ing the pressure with the twist of a handle.There is no other cold water pressure washerthat offers so much in cleaning effectiveness.

DG SeriesCold Water Pressure Washer• Gasoline Powered• Direct Drive Pump• PortableThe DG is a gasoline-powered direct-drive,cold water pressure washer with the cleaningpower of up to 3.8 GPM and 3500 PSI. Builton compact sturdy steel frames, each unitfeatures a dependable industrial-grade Hondaengine, a tri-plunger, oil-bath Kärcher pumpwith a limited 7-year warranty and EZ startvalve for convenience in pull starting theengine. DG models have a hose-and-gunrack, high-pressure hose rated for up to 4500PSI, detergent injector and 10-inch tubedpneumatic tires for easy maneuvering in allterrain. All DG models are ETL certified to therigid UL-1776 pressure washer safety stan-dards. Ideal for marinas and boats, cars andtrucks, home siding, plant maintenance,decks, butters, driveways and fences.

MODEL PSI GPM PUMP DRIVE PUMP ENGINE HP START BURNER BTU DIESEL TANK GAS TANKSGP-303037 3000 2.6 Direct Kächer/Crankcase Honda 9 Recoil 12V DC 280,000 6 gal. 1.5 gal.SGP-353037 3000 3.5 Direct Kächer/Crankcase Honda 11 Recoil 12V DC 326,000 6 gal. 1.5 gal.SGP-353037E 3000 3.5 Direct Kächer/Crankcase Honda 11 Electric 12V DC 326,000 6 gal. 1.5 gal.SGP-403537E 3500 3.5 Direct Kächer/Crankcase Honda 13 Electric* 12V DC 326,000 6 gal. 1.5 gal.

*Only model that ships with batteryMODEL PSI GPM PUMP DRIVE PUMP RPM ENGINE ENGINE HP FUEL START DIMENSIONSBR-353237 3200 3.5 Belt Kächer/Crankcase Honda GX 13 Gas Recoil 42"L x 26"W x 30"HBR-373537 3500 3.7 Belt Kächer/Crankcase Honda GX 13 Gas Recoil 42"L x 26"W x 30"HBR-404027* 4000 4.0 Belt Kächer/Crankcase Vanguard 16 Gas Recoil 42"L x 26"W x 36"HBR-343067E* 3000 3.4 Belt Kächer/Crankcase Kohler 10 Diesel Electric‡ 42"L x 26"W x 36"HBR-405037E* 5000 4.0 Belt Kächer/Crankcase Honda 20 Gas Electric‡ 42"L x 26"W x 36"HBR-455037E* 5000 4.5 Belt Kächer/Crankcase Honda 24 Gas Electric‡ 42"L x 26"W x 36"H

*Tandem-axle model ‡Battery not includedMODEL PSI GPM PUMP DRIVE PUMP PUMP RPM ENGINE ENGINE HP ENGINE RPM DIMENSIONSDG-232437 2400 2.3 Direct Kächer/Crankcase 3400 Honda GX 5.5 3400 35"Lx21"Wx24"HDG-252737 2700 2.5 Direct Kächer/Crankcase 3400 Honda GX 6.5 3400 35"Lx21"Wx24"HDG-303037 3000 3.0 Direct Kächer/Crankcase 3400 Honda GX 9.0 3400 35"Lx21"Wx24"HDG-383537 3500 3.8 Direct Kächer/Crankcase 3400 Honda GX 13 3400 35"Lx21"Wx24"H

134

535-

9-10

VACUUM

WET/DRY VACUUMWith unique air filtration and noise level features

LIFETIME WARRANTY ON CANISTER -ONE-YEAR LIMITED WARRANTY ON VACUUMFEATURES:

• Electrical system is double protected.• Wet and dry cartridge filter (no conversion necessary).• High impact poly construction canister.• Industrial grade polyolefin wheels with stainless

steel shafts.• Two-stage blower motor for longer life.• Self-cooling motor design.• Quiet operation.• Exhaust air ducting reduces the possibility of motor

contamination by dirt or moisture.• 25-foot electrical cord.• Electrical cord wrap.• Drain outlet.• Recessed wheels and clamps.• Stackable design for easy storage.• Filter efficiency 99.5% to 1.0 micron (optional HEPA

filter 99.7% efficient to 0.3 micron).• Eliminates airborne particles through exhaust.• CSA certified.

MODEL MV-1800-OMEVMotor 120V, Two-stage bypassHP 1.6CFM 120Waterlift 102 in.Capacity 18.0 gallonsWater Recovery 13.0 gallonsAMPS 8.3Dimension (LxWxH) 27 x 19 x 31Shipping Weight 55 lbs.Net Weight 44 lbs.

SPECIFICATIONS

MV-1800-OMEV

EACH UNIT INCLUDES:• 10-foot x 1½ inch crushproof hose.• 2-piece aluminum extension wand.• 14-inch commercial squeegee tool.• 12-inch combination floor tool.• 10¾-inch crevice tool.• 5-inch upholstery tool.• Cartridge filter.• 1 paper filter bag (replacement bags sold

in packs of ten).

EXCLUSIVE “HYDRO” FLOW FILTER (#19-0230)• Designed for continuous water pick-up.• Will not clog or deteriorate.• Retains maximum air flow.• Completely washable.• Water resistant.• 99.5% efficient to 1.0 micron.• 1.0 micron rating prevents drywall dust from

damaging motor and eliminates airborne dust.

+1.0 Micron

-1.0 Micron

Wet Pick-Up Dry Pick-Up

135

5

SPECIFICATIONS

535-

8-10

AIR COMPRESSORS

AIR COMPRESSORSElectric/Gasoline - Single Stage

AM1-PE15-08M ELECTRIC AIR COMPRESSOR

FEATURES:• 14-gauge powder coated two-piece belt guard

with 1/4-turn release for quick access to belts.• Industrial UL listed electric motor.• Auto start/stop (continuous run optional).• Industrial grade pressure switch.• Thermal overload motor protection.• Quality cast iron single stage compressor.• Stainless steel braided discharge hose.• Belt tightening system pulls engine straight to

ensure constant belt alignment.• Regulator and two gauges for tank and outlet pressure.

AM1-PH65-08M GASOLINE AIR COMPRESSOR

FEATURES:• Quality cast iron single stage compressor.• Stainless steel braided discharge hose.• Belt tightening system pulls engine straight to

ensure constant belt alignment.• Regulator and two gauges for tank and

outlet pressure.• Quality pilot valve unloader.• Pneumatic idle control to conserve fuel.• 14-gauge powder coated two-piece belt guard

with 1/4-turn release for quick access to belts.• Industrial OHV Honda engine.

MODEL AM1-PE15-08M AM1-PH65-08MMotor 120V, 13.2A Electric -Engine - Honda OHVHP/Displacement 1.5 hp 196ccCFM @ 100 PSI 6.5 13.1Plug Type Nema 5-15P -Pump Cast iron Cast ironDimension (LxWxH) 44.5 x 18.5 x 25 44.5 x 18.5 x 26Shipping Weight 190 200Net Weight 170 175

AM1-PE15-08M

AM1-PH65-08M

ADDITIONAL FEATURES:• Splash lubricated cast iron crankcase.• Aluminum head for heat dissipation.• Large canister intake filter.• Fly wheel for extra cooling and longer life.

(12 inch on Honda models and 10 inch on electric models)• Powder coated 8-gallon twin tank receivers.• Convenient lifting handles.• 7-gauge base plate to reduce vibration.• Pneumatic tire with tube and steel hub.• Manual drain valves for proper maintenance.

136

535-

10-1

0

JOBSITE BOXES

JOBSITE BOXES PROVIDE SUPERIOR PROTECTIONFOR TOOLS AND WORK GEAR

FEATURES:• Special tamper-proof armored locking system

for protection against break-ins.• Reinforced support skids for increased

protection and easy transporting.• Convenient, swing out handles for

additional mobility.• Special locking lid support locks the lid open

to prevent accidental closings.• Heavy-duty solid steel construction with full

arc welded seams.• Special powder coated finish for

extreme durability.• Full-length concealed hinges are riveted for

additional protection and strength.• Predrilled skids for easy caster installation.• Optional removable tool trays to assist

tool management.

SPECIFICATIONS

MB-3619

MB-4830

ACCESSORIES :

Casters: MX-4 (4-inch)MX-5 (5-inch)MX-6 (6-inch)

Tool Trays: MX-19 fits MB-3619MX-30 fits MB-4830

MODEL MB-3619 MB-4830

Cubic feet 6.33 25.00

Dim. (L x W x H) 36 x 19 x 16 48 x 30 x 30

Shipping Weight 83 lbs 174 lbs

Net Weight 81 lbs 168 lbs

137

5

710-

1-10

ELECTRIC SUBMERSIBLE PUMPS

LB GENERAL DEWATERING PUMPS

Compact and PowerfulPowerful pumps built with durable materials in an easy handling design.Top discharge provides maximum motor cooling efficiency allowing continuous duty operation at low water levels andextended dry-run capability.

Model LB-480A automatic submersible pump handles like the non-automatic version in every aspect of construction siteusage requiring a tough and durable pump.

LB-480 Features• Synthetic rubber wear parts and semi-

vortex impeller for maximum durability.• V-ring system protects the shaft seal

from abrasives.• Easy disassembly with one 12mm

box/socket wrench.• Vertical or horizontal discharge.• Patented oil lifter extends shaft seal life up

to 10 times.Optional Accessories• TS-301 Float Switch for automatic operation.

LB-480A Features• No control panel or float switches required.• Handles like the non-automatic pump - no special

installation procedures.• Requires very small space to operate - only 8-3/4" diameter.• Urethane, Semi Vortex Impeller and Wear Plates for

maximum durability and maintaining pump performance.• Double Inside Mechanical Seal with SiC faces provides

the longest operational life.• Oil Lifter provides lubrication of the seal faces.

(Patent Pending)• V-Ring Seal Protector protects mechanical

seal from abrasive particles.

Technical Features of EL-1 Relay Unit• Sensitive electrodes detect water to start

pump operation even when foreign materialsare present.

• Internal timer eliminates chattering operationin rough water to extend motor life.

• Relay sensor completely molded in resin andcovered by rubber case for protectionagainst rough handling.

• Jobsite tested for more than 30,000 on-offcycles without failure or damage.

LB-800 Features• Designed to fit an 8" pipe.• Up to 60' shut off head.• Lightweight, compact design.• Available in 220V single-phase for

lower amperage draw and longercable extensions.

Optional Accessories• Float switch for automatic operation

TS-302 for 110V, TS-303 for 220V.• 3-inch NPT coupling available

HS SAND/SOLIDS TRASH PUMP

Pump sand, solids and debris with minimal wear, clogging.

HS2.4S-62 Features• Built-in shaft mounted agitator suspends solids.• Urethane Semi Vortex Impeller for maximum durability and

maintaining pump performance.• Double inside mechanical seal with SiC faces provides the

longest operational life.• Oil Lifter provides lubrication of

the seal faces. (Patent Pending)• V-Ring Seal Protector protects

mechanical seal from abrasive particles.

Optional Accessories• TS-301 Float Switch for

automatic operation.• Vertical Discharge Coupling.• Residue Kit for 0.4 inch

pump down.

NK HEAVY-DUTY, HIGH HEAD PUMP

Capable of handling abrasive materials with minimal wear.

NK2-15 Features• Terminal board for voltage reconnect

(NK2-15 only).• Semi Vortex Impeller and Synthetic

Rubber Wear Plates for maximumdurability and maintaining pumpperformance.

• Double Inside Mechanical Seal with SiC faces provides the longestoperational life.

• Oil Lifter provides lubrication of theseal faces. (Patent Pending)

• V-Ring Seal protector protectsmechanical seal from abrasive particles.

Optional Accessories• TS-303 Float Switch for automatic

operation (220V only).• Sand kit to suspend solids and

prevent clogging.• 2-inch NPT coupling available.

138

710-

2-10

ELECTRIC SUBMERSIBLE PUMPS

ELECTRIC SUBMERSIBLE SPECIFICATIONS

HS2.4S-62 LB-480 LB-480A LB-800 NK2-15Sand/Solids Dewatering Automatic Operation SlimLine Pump Heavy-duty & High Head

FLUID Trash PumpMax. Capacity (GPM) 53 62.4 62.4 73 111Max. Head (ft.) 39 39.5 39.5 59 69Solids Dia. (in.) 3/8 1/4 1/4 1/4 1/3PUMPImpeller Type Semi-Vortex Semi-Vortex Semi-Vortex Semi-Vortex Semi-VortexImpeller Material Urethane Rubber Urethane Rubber Urethane Rubber Urethane Rubber Ductile Iron

CastingCasting Material Grey Iron Ethylene Propylene Ethylene Propylene Natural Rubber Ethylene Propylene

Casting Rubber Rubber RubberWear Plate Material (Integral part Urethane Urethane Natural Rubber (Integral part

of casing) Rubber Rubber of casing)Shaft Seal - Type / Material Double inside mechanical seal with Silicon Carbide on Silicon Carbide faces Silicon Carbide on Silicon

on lower seals and Carbon on Ceramic faces on upper seals. Carbide faces on upper andlower seals.

Seal Lubricant - Type SAE 10W/20W or Turbine Oil (ISO VG32)Seal Lubricant - Amount, oz. 5.4 6.1 6.1 5.2 9.1Seal Protection V-Ring & Oil Lifter V-Ring & Oil Lifter V-Ring & Oil Lifter Lip Seal V-Ring & Oil LifterDischarge Connection 2" NPT Coupling 2" NPT Coupling 2" NPT Coupling 2" NPT Coupling 3" NPT CouplingMOTORMotor Output (hp) 1/2 hp 2/3 hp 2/3 hp 1 hp 2 hpPhase Single Phase Single Phase Single Phase Single Phase Single PhaseVoltage 110V 110V 110V 110V or 220V 110V or 220VAmperage - Rated Current 5.4 6.1 6.1 11.5 - 110V 23.0 - 110V

6.5 - 220V 11.5 - 220VAmperage - Starting Current 12.5 12.5 12.5 43.0 - 110V 136 - 110V

25.5 - 220V 68.0 - 220VType Continuous duty, Air filled, 3600 RPM, 60 HzBearings Double shielded, Permanently lubricated, High-temp C3 with Double shielded,

B-10 life of 60,000 hours. Permanently lubricatedInsulation Class B E E E BMotor Protector (Built-in) Miniature Protector Miniature Protector Miniature Protector Circle Thermal Circle Thermal

Protector ProtectorPlug Configuration (Nema) 5-15P 5-15P 5-15P 5-15P (110V) No Plug

No Plug (220V)Cable - Conductors x AWG 3C x 16 AWG 3C x 16 AWG 3C x 16 AWG 3C x 14 AWG 3C x 12 AWGStd. Cable Length 20 feet 32 feet 32 feet 50 feet 32 feetMax. Cable Length 70 feet 62 feet 62 feet 53 ft. - 110V 46 ft. - 110V

187 ft. - 220V 185 ft. - 220VMin. Generator Cap. (Watts) 1300 1300 1300 3300 6000Optional Float Switch TS-301 TS-301 n/a TS-302 (110V) TS-303 (220V

TS-303 (220V) operation only)DIMENSIONMax. Diameter (in.) 10-1/16 7-3/8 8-3/4 7-1/2 9-7/16Max. Height (in.) 12-15/16 11-3/16 11-3/16 13-7/16 24-1/2Continuous Running

Water Level (in.) 3-1/2 2 4-1/2 3-1/8 3-1/4Pump Weight (lbs.) 30 28 30 35 81Shipping Weight (lbs.) 30 28 30 35 81

139

5

710-

3-10

TRASH PUMPS

EPT HEAVY-DUTY TRAILER MOUNTED

EPT2-100DD EPT2-150DD EPT3-150YD4" Heavy-duty Trash Pump 6" Heavy-duty Trash Pump 6" Heavy-duty Trash Pump

FLUIDMax. Capacity (GPM) 666 1400 1300Max. Capacity (GPH) 40000 84000 78000Max. Head (ft.) 94 86 120Max. Solids Diameter (in.) 2 3 3PUMPImpeller Type Semi-Open Semi-Open Semi-OpenImpeller (Diaphragm) Material Ductile Iron Ductile Iron Ductile IronVolute Casting Material Cast Iron Cast Iron Cast IronWear Plate Material Rubber Lined Cast Iron Rubber Lined Cast Iron (Integral part of volute)Pump Casting Material Cast Iron Cast Iron Cast IronShaft Seal Tungsten Carbide Mechanical Seal Tungsten Carbide Mechanical Seal Carbon/Chrome Mechanical SealSeal Lubricant Grease (Oil optional) Grease (Oil optional) GreaseDischarge Connection 4" NPT Coupling 6" NPT Coupling 6" NPT CouplingSuction Connection 4" NPT Coupling 6" NPT Coupling 6" NPT CouplingENGINEBrand DEUTZ DEUTZ YANMARModel F2L1011 F3L1011 3TNV88Type Air/Oil Cooled, 4-Cycle, Two Cylinder Air/Oil Cooled, 4-Cycle, Three Cylinder Air/Oil Cooled, 4-Cycle, Three Cylinder

with Temperature/Oil Sensor with Temperature/Oil Sensor with Temperature/Oil SensorOutput (hp) 24.5 hp 36 hp 30 hpRPM 2800 2800 3000Fuel Diesel Diesel DieselFuel Tank Capacity (US Gal.) 40 40 40Continuous Run Time

Per Tank (Hr.) 24 24 24Starting Method Electric, 12V Electric, 12V Electric, 12VDIMENSIONShipping Dimensions

Length (in.) 100 100 111Width (in.) 63-1/2 63-1/2 60Height (in.) 59 59 69Shipping Weight (lbs.) 1800 2100 1750

Trailer Mounted TrashPumps for Tough JobsDewatering to sewage, clean water to3-inch solids—our trash pumps do it all.

EPT2-100DD and EPT2-150DD Features• Heavy-duty Deutz diesel engine with electric start and

40 U.S. gallon fuel tank provides a minimum of24 hours run time per tank.

• Pass 3" solids (EPT2-150DD) or 2" solids(EPT2-100DD) with non-clog, wear resistant ductileiron impeller on 304 stainless steel shaft sleeve.

• Oil and abrasion resistant, rubber-lined front and rearwear plates.

• Long-life grease lubricated tungsten carbidemechanical seals (optional oil lubricatedseals available).

• Heavy-duty DOT road trailer with 15" 6-ply tires and2" ball hitch (optional pintle hitch available).

140

173-

3-10

VENTILATION BLOWEREQUIPMENT COMPANY

manufacturers of light constructionequipment

General®

NONHAZARDOUS LOCATION AIR VENTILATION BLOWERSGeneral’s line of portable air blowers can accommodate most nonhazardous confined space ventilationrequirements. Select from 8" or 12" diameter units with power choices of 12VDC or 115 VAC. Bothradial and axial housing configurations are available for the most demanding air flow applications.

Blowers are ideal for supplying fresh air around construction sites; removing toxic and noxiousatmospheres from confined work spaces; detecting sewer line leaks and providing fresh air whenworking in tanks and vaults. Proper ventilation increases safety and worker productivity rates whileconforming to tough federal and state OSHA regulations.

Each unit is designed to General’s highest quality standards for uncompromised utility and investmentreturn. There are no plastic parts to crack. Constructed with heavy-gauge aluminum and steel, all Generalblowers offer laboratory certified air flow rates from independent, third party, agency testing.

Breathe easier with a General blower on the jobsite...cost effective solutions to confined space ventilation.

MODEL EP8 EP8DC EP8DC15 EP8DC25 EP8AC EP8AC15 EP8AC25 EP12ACBLOW-R-PAC® BLOW-R-PAC® BLOW-R-PAC® BLOW-R-PAC®

POWER 1/3 HP(.23kw) 1/6 HP (.13 kw) 1/6 HP (.13 kw) 1/6 HP (.13 kw) 1/4 HP (.20 kw) 1/4 HP (.20 kw) 1/4 HP (.20 kw) 3/4 HP (.52kw)SOURCE 1725 RPM, 60 Hz 3450 RPM, 12 volts 3450 RPM, 12 volts 3450 RPM, 12volts 3200RPM, 60 Hz 3200 RPM, 60Hz 3200 RPM, 60HZ 3450 RPM,60 Hz

115 volts AC, capacitor 13 amperes, sleeve 13 amperes, sleeve 13 amperes, sleeve 115/230 volts, AC 115 volts AC, capacitor 115 volts AC, capacitor 115/230 volts AC, capacitorstart, 4.2 amperes, full bearing and thermal bearing and thermal bearing and thermal capacitor start, 2.5 start, 2.4 amperes full start, 25 amperes full start, 8.8/4.4 amperes fullload, ball bearing and protection equipped protection equipped protection equipped amperes full load, ball load, ball bearing and load, ball bearing and load, ball bearing and thermalthermal protection bearing and thermal thermal protection thermal protection protection equipped. Motor isequipped protection equipped equipped equipped factory wired for 115 volts

SPEEDCONTROL Single speed Single speed Single speed Single speed Single speed Single speed Single speed Single speed

BLOWERType Radial Axial Axial Axial Axial Axial Axial Axial

Material Cast aluminum Spun steel Spun steel Spun steel Formed steel Spun steel Spun steel Formed steel

Wheel Type Steel multivane Aluminum/plastic Aluminum/plastic Aluminum/plastic Aluminum/plastic Aluminum/plastic Aluminum/plastic Aluminum/plasticMultiWing® axial MultiWing® axial MultiWing® axial MultiWing® axial MultiWing® axial MultiWing® axial MultiWing® axial

Size 8" (203mm) nominal 8" (203mm) nominal 8" (203mm) diameter 8" (203mm) diameter 8" (203mm) nominal 8" (203mm) diameter 8" (203mm) diameter 12" (305mm) nominaldiameter inlet/outlet diameter outlet x 15' (4.5m) integral x 25' (7.6m) integral diameter inlet/outlet x 15' (4.5m) integral x 25' (7.6m) integral diameter inlet/outlet

duct duct duct duct

GENERALMounting Rubber Rubber Rubber Rubber Direct Rubber Rubber Rubber

Type Anti-vibration Anti-vibration Anti-vibration Anti-vibration Steel base Anti-vibration Anti-vibration Anti-vibration

Weight 53 lbs. (24kg) 26 lbs. (19kg) 47 lbs. (32kg) 57 lbs. (26kg) 23 lbs.(10.6kg) 43 lbs. (20kg) 53 lbs. (24kg) 65 lbs. (29.5kg)

DIMENSIONSHeight 19-3/4" (502mm) 13-1/2" (343mm) 13-1/2" (343mm) 13-1/2" (343mm) 11-1/2" (292mm) 13-1/2" (343mm) 13-1/2" (343mm) 15-1/2" (394mm)

Length 18-1/4" (464mm) 15-1/4" (387mm) 30-1/2" (775mm) 42-1/2" (1080mm) 18" (457mm) 30-1/2" (775mm) 42-1/2" (1080mm) 18-1/2" (470mm)

Width 14-1/2" (368mm) 11-3/4" (298mm) 11-3/4" (298mm) 11-3/4" (298mm) 8-1/8" (206mm) 11-3/4" (298mm) 11-3/4" (298mm) 12-5/8" (321mm)

Specifications

15 good reasons why your next electrically powered air ventilation blower should be a GENERAL Model EP8:• 11-gauge steel frame to better resist abuse and damage.• Watertight power cord strain relief fitting. Rigged and durable.• Flow thru ventilation. Helps motor run cooler and longer.• 1/3 HP electric motor with 1.5 service factor. Runs cooler.• Capacitor start electric motor required less amperage. Operates from a smaller generator.• Fuse protection guard, Helps prevent damage during transport.• Balanced carry handle. Comfortable and functional.• Permanently affixed aluminum data plates. More durable than a decal.• Durable inlet and exhaust screens meet CSA and OSHA requirements.• All flow rates tested and certified by an independent testing laboratory.• Cast aluminum blower housing. More durable than sheet metal. No seams or spotwelds to break.• All metal squirrel cage type blower wheel. No warping or cracking with use.• ON/OFF switch guard. Helps prevent damage during transport.• 14-3 AWG power cord material meets the more stringent CSA certification requirements.• Designed and manufactured to the more stringent Canadian StandardsAssociation (CSA) certification requirements.EP8

EP8

141

5

874-

3-10

LIGHT CONSTRUCTIONEQUIPMENT

The SB Hopper Broom is an excellent choice for heavy-dutyclean-up. It easily picks up asphalt milling spoils, gravel,construction debris and other heavy materials, moving thedebris into the larger hopper for disposal. To pick up dirtand lighter material, simply reverse the broom and thelighter material is collected in the hopper.

Applications:• Handles light and heavy-duty clean-up

in construction, industrial andmunicipal applications.

• Optional sprinkler kit with or without25-gallon tank.

• Fits skid-steers, backhoe-loaders, wheel loaders and utility loaders.

Features:• Bi-directional broom sweeps

forward to pick up dirt – reverses to collect asphalt millings, rock and construction debris.

• To dump, just lift and tilt – no chains.• Direct-drive brush motors eliminate

chains and sprockets.• No front caster wheel – works easily

next to walls, curbs and obstacles.• Replaceable bolt-on cutting edge

on bucket.• Available in three widths: 60", 72" and 84".

Factory-installed hydraulically powered vacuum attachment for Sweepster Collector Sweeping Models.Collects and filters out airborne particulate during sweeping operation for virtual dust-free sweeping without the need for water sprinkler systems.

Features:• Dust control without messy, bulky,

impractical water sprinkler systems to continually refill.

• Washable teflon-coated filter – works in dry or wet conditions.

• Virtually eliminates airborne particulateejection (above 10 micron) duringthe sweeper operation.

• Electrically operated operator-controlledvibration device cleans the filterbetween washings.

• Can be ordered as a factory-installedoption on any of the Sweepster Collector sweepers.

• Multiple valve packages availableto match attachment to SweepsterCollector sweeper models andcarrier specifications.

• Can be used in conjunction with GutterBroom option as well.

• Powder-coated all steel body forprotection and durability.

• 59"L x 27"W x 13"H. Weight: 175 lbs.

Pick-Up Sweeper VacuumAttachment

SB Hopper Broom

142

651-

7-10

SCAFFOLDS

PPrroo--JJaaxx UUttiilliittyy SSccaaffffoolldd PPaacckkaaggeess

GUARD RAIL & OUTRIGGER PACKAGESPart No. Description Set Wt.#

0127-149-06 6' Complete Guard Rail Pkg. (2 pcs.) 68

0127-150 Narrow Outrigger Package (4 pcs.) 32

NOTE: Guard railing is required by OSHA on all platforms 10' or higher.

MaximumWorkingHeight

OverallHeight

MaximumPlatformHeight**

MinimumPlatformHeight

Single Unit w/oGuard Railing

Single Unit w/Guard Railing

2 Single Units w/Guard Railing &

Narrow Outriggers

2 Single Units, 1-65" Add.Ht. Unit w/Guard Railing &

Wide Outriggers

When platform height exceeds 4', guard railing is recommended but not required.

0127-149-(06*)6' Complete Guard

Rail Pkg.(2 pieces)0127-(006*)-1

Single Unit w/Guard Railing

0127-(006*)-0Single Unit

HINGED PLATFORMS FOR INSIDEACCESS AVAILABLE.PACKAGES ARE AVAILABLE WITHEXPANDED METAL DECKS.

23' 6"

20' 6"

18'

15'

12' 6"

10' 6"

9' 6"

6'

2'

4'w/oG.R.

6'w/

G.R.

11' 6"w/

G.R.

17'w/

G.R.

PRO-JAX STEEL PACKAGESPart No. Length Platform Ht.Range Max.Wk.Ht. Overall Ht. Gd. Rail Outrig. Wt.#

0127-006-0 6' 2'4" 10'6" 6' No No 152

0127-006-1 6' 2'6" 12'6" 9'6" Yes No 240

Includes frames, braces, platform and casters. Outriggers and guard rails included where applicable.

143

5

651-

08-1

0

SCAFFOLD / ACCESSORIES

144

Hoist Arm / Well WheelPart No. Description Capacity Wt. lb.

0041-028 ST-65-HS Swivel Head Hoist Arm 100* 29

0082-0103 WP-65-W-10 10" Well Wheel 200* 13.5

*Rated to lift 100 lb. load using well wheel and rope.

Step Type Brackets

Hoist Arm / Well Wheell

Guard Rail Systems

Casters

Leveling Jacks

Diagonal Braces

Must Specify Tube & LockFrame Tube Size: 7 - 1-11/16"

_-0243_ 4' W x 3' H 22#_-0253_ 5' W x 3' H 24#

_-0244_ 4' W x 4' H 29.5#_-0254_ 5' W x 4' H 33#

_-0245_ 4' W x 5' H 35#_-0255_ 5' W x 5' H 39#

_-0246_ 4' W x 6' H 42#*7-0247_ 5' W x 6' 4" H 44#

_-0248_ 4' W x 6' 6" H 43#_-0256_ 5' W x 6' H 45#

*7-0257_ 5' W x 6' 4" H 54#_-0258_ 5' W x 6' 6" H 47#

Side BracketAngle Iron Hanger

Tube End0039-720

End BracketEnd and Side Hanger

Tube End0039-520

• Available in three stem sizes to fitthe three tube sizes offered.

• All Caster include 0068-061 - 2"snap pin for fastening caster toframe leg.

• Available in capacities from 250-500 pounds.

• All bil-jax casters include wheeland swivel bakes.

• Made from cold rolled steel with plated roll formedthreads for durability and long life. Plated finish.

0026-7_2w/Snap PIn

0026-9_2w/Snap PIn

Only use hole endguard rails.Type UC Post

Steel Toeboard

Guard Rail Posts

*NOTE: When ordering 6'6" H frameswith 1-11/16" tube size (7) , height offrame is 6' 4" (listed separately above).

Extension with retainer0034-08-_

Swivel0032-09-_

Rigid0032-08-_

Diagonal BracesPart No. Description Frame Spacing Wt. lb.

0010-02-07 ST-72-7H-24 24" lock spacing 7' Sp. 11.5

0010-03-07 ST-72-7H-36 36" lock spacing 7' Sp. 11.75

0010-04-07 ST-72-7H-48 48" lock spacing 7' Sp. 12

0010Hole End

Use with all otherbil-jax Lock Types

Well Wheel0082-0103

Hoist Arm0041-028

Swivel10"

549-

23-1

0

WORK PLATFORMS

WORK PLATFORMS FOR USE WITH STEEL SCAFFOLDS5300 SERIES — PLYWOOD DECKED ALUMA–PLANK®

Model 5307-19

Specifications:Duty Rating Side Rail Side Rail

Model No. /Sq. Ft. Width Length Depth Weight

5307-19 75 lbs. 19-1/16" 7' 3-1/2" 27 lbs.

Task-Master Aluminum Stages

On 5" or 6" depth stages, adouble row of rungs give extrarigidity and less deflection.Allows 30' spans with no trusses.

Double end rung feature onstages with 6" rails.

Individual slip-resistant deckingminimizes paint or materialbuild-up.

Side Rail Side Rail ShippingModel No. Length Width Depth Flange Weight

1-man 250 lbs. rated:2012 12' 12" 4" 1-3/8" 36.02016 16' 12" 4" 1-3/8" 48.02020 20' 12" 5" 1-3/8" 65.02024 24' 12" 5" 1-3/8" 78.0

2-man 500 lbs. rated:2330 30' 12" 6" 1-3/8" 140.02412 12' 14" 4" 1-3/8" 40.02416 16' 14" 5" 1-3/8" 58.02420 20' 14" 6" 1-3/8" 85.02424 24' 14" 6" 2" 109.02612 12' 24" 4" 1-3/8" 56.02616 16' 24" 5" 1-3/8" 81.02620 20' 24" 6" 1-3/8" 115.02624 24' 24" 6" 1-3/8" 138.02628 28' 24" 6" 2" 180.0

145

5

1022

-6-1

0

FORKLIFTWORK PLATFORM

Safety Work PlatformDesigned for rough terrain forklifts – provide an economical andsafe way to elevate personnel on all types of construction. Theseplatforms safely elevate personnel for maintenance work, painting,inventory, and lots more jobs around the warehouse or in the plant.

UNIVERSAL FIT “SLIP ON THE FORKS” MODELSModel Size Shipping Weight1204B 4 ft. x 4 ft. 310 lbs.1206B 4 ft. x 6 ft. 380 lbs.1208B 4 ft. x 8 ft. 425 lbs.1210B 4 ft. x 9 ft. 8 in. 505 lbs.

Specifications:• Full Perimeter Guard Rail System constructed of

1-1/2" square steel tubing and consisting of a 42" high top rail, a mid rail and 5-1/2" high intregel toeboards. Access gates with spring pin latches are provided at eachend. Entire Guard Rail System can be easily removed and laid flat inside platform for transportation.

• Deck consists of a strong but lightweight engineered steelframe with expanded metal deck.

• The Universal Fit “Slip on the Forks” design can be used with both Extendible Reach and Straight Mast forklifts. Forks slide into steel fork pockets and are secured with two heavy-duty steel pins behind the heel of the forks. They are designed for use with a 48" or wider carriage and 48" long forks up to 7" wide and 2-3/4" thick. Forks longer than 48" can be used, however, they will extend out past the front of the platform.

• The Quick-Tach models are built to fit specific makesand models of forklifts that are equipped with a Quick-Tach. The forks and carriage are removed and the platform attaches to the boom.

• All Models are rated at 1,000 lbs. load capacity. Rating applies to platform only and does not reflectcapacity of forklift.

“Slip on the Forks”style

OPTIONAL MAST PROTECTIONSCREEN (Model 1250) protectspersonnel from moving partsof forklift mast. Constructedof square steel tubing andexpanded metal, the screenmeasures 42" wide x 84" tall.It attaches to the back guardrailwith u-bolts. A mast protectionscreen should be used with allstraight mast forklifts and withany others where a mast posesa safety hazard.

ELEVATE PERSONNEL

Model 1203B 3' x 3'Model 1244B 4' x 4'

INDUSTRIAL WORK PLATFORM

“QUICK-TACH” MODELSModel Length Shipping Weight

1204BQT 4 ft. x 4 ft. ±460 lbs.1206BQT 4 ft. x 6 ft. ±530 lbs.1208BQT 4 ft. x 8 ft. ±575 lbs.1210BQT 4 ft. x 9 ft. 8 in. ±635 lbs.

• Heavy-duty construction - 1,000 lbs. capacity

• Secures to forks with simple “Positive Pin Locking System”

• Front mid rail raises for entrance - no gate to be left open

• Built-in 84" high MastProtection Screen (upper half removable for transportation and storage)

• Integral full perimeter toeboard

146

1101

-1-1

0

SLINGS

Types 1 and 2

Type 1 - Sling made with a triangle fitting on one end and a slottedtriangle choker fitting on the other end. It can be used in a vertical,basket or choker hitch.

Rated Capacities in Lbs. Type 1 Type 2** Vertical Choker Basket(TC) (TT)

TC1-802 TT1-802 3,200 2,500 6,400TC1-803 TT1-803 4,800 3,800 9,600TC1-804 TT1-804 6,400 5,000 12,800TC1-805 TT1-805 8,000 6,400 6,000TC1-806 TT1-806 9,600 7,700 19,200TC1-808 TT1-808 12,800 10,200 25,600TC1-810 TT1-810 16,000 12,800 32,000TC1-812 TT1-802 19,200 15,400 38,400TC1-816 TT1-816 25,500 20,400 51,000TC1-818 TT1-818 28,700 23,000 57,400TC1-820 TT1-820 32,000 25,600 64,000TC1-824 TT1-824 38,400 30,700 76,800 TC2-802 TT2-802 6,400 5,000 12,800TC2-803 TT2-803 8,600 6,900 17,200TC2-804 TT2-804 11,500 9,200 23,000TC2-805 TT2-805 14,000 11,200 28,000TC2-806 TT2-806 16,800 13,400 33,600TC2-808 TT2-808 22,400 17,900 44,800TC2-810 TT2-810 28,000 22,400 56,000TC2-812 TT2-812 33,600 26,800 67,200 TC2-816 TT2-816 44,800 35,800 89,600TC2-818 TT2-818 50,400 40,300 100,800TC2-820 TT2-820 56,000 44,800 112,000TC2-824 TT2-824 67,200 53,700 134,400

**TYPE 2 - Sling made with a triangle fitting on both ends. It can beused in a vertical or basket hitch only. This sling cannot be used ina choker hitch.

CAUTION DO NOT EXCEED RATED CAPACITIES.

TYPES 3 and 4

TYPE 3 - Sling made with a flat loop eye on each end with loop eyeopening on same plane as sling body. This type of sling is some-times called a flat eye and eye, eye and eye, double eye sling.

Twisted Rated Capacities in Lbs. Flat Eye EyeType 3 Vertical Choker Basket Type 4(EE) (EE)

EE1-801 1,600 1,250 3,200EE1-802 3,200 2,500 6,400EE1-803 4,800 3,800 9,600EE1-804 6,400 5,000 12,800EE1-805 8,000 6,400 16,000EE1-806 9,600 7,700 19,200EE1-808 12,800 10,200 25,600EE1-810 16,000 12,800 32,000EE1-812 19,200 15,400 38,400 EE2-801 3,200 2,500 6,400EE2-802 6,400 5,000 12,800EE2-803 8,600 6,900 17,200EE2-804 11,500 9,200 23,000EE2-805 13,600 10,900 27,200EE2-806 16,300 13,000 32,600EE2-808 19,200 15,400 38,400EE2-810 22,400 17,900 44,800EE2-812 26,900 21,500 53,800EE3-801 4,100 3,300 8,200EE3-802 8,300 6,600 16,600EE3-803 12,500 10,000 25,000

EE3-804 16,000 12,800 32,000EE3-805 19,200 15,400 38,400EE3-806 23,000 18,400 46,000EE3-808 30,700 24,500 61,400EE3-810 36,800 29,400 73,600EE3-812 44,000 35,200 88,000 EE4-801 5,000 4,000 10,000EE4-802 10,000 8,000 20,000EE4-803 14,900 11,900 29,800EE4-804 19,800 15,800 39,600EE4-805 24,800 19,800 49,600EE4-806 29,800 23,800 59,600EE4-808 39,700 31,700 79,400EE4-810 49,600 39,600 99,200EE4-812 59,500 47,600 119,000

**TYPE 4 - Sling made with both loop eyes formed as in Type III,except that the loop eyes are turned to form a loop eye which is at aright angle to the plane of the sling body. This type of sling is com-monly referred to as a twisted eye sling.CAUTION DO NOT EXCEED RATED CAPACITIES.

TYPES 5Type 5 - Endless sling, sometimes referred to as a grommet. It is acontinuous loop formed by joining the ends of the fabric togetherwith a splice.

Rated Capacities in Lbs.Type 5 Vertical Choker Basket (EN)

EN1-801 3,200 2,500 6,400EN1-802 6,400 5,000 12,800EN1-803 8,600 6,900 17,200EN1-804 11,500 9,200 23,000EN1-805 13,600 10,900 27,200EN1-806 16,300 13,000 32,600EN1-808 19,200 15,400 38,400EN1-810 22,400 17,900 44,800EN1-812 26,900 21,500 53,800EN2-801 6,200 4,900 12,400EN2-802 12,200 9,800 24,400EN2-803 16,300 13,000 32,600EN2-804 20,700 16,500 41,400EN2-805 24,500 19,600 49,000EN2-806 28,600 23,000 57,200EN2-808 30,700 24,500 61,400EN2-810 33,600 26,800 67,200EN2-812 37,600 30,000 75,200EN3-801 8,000 6,400 16,000EN3-802 16,000 12,800 32,000EN3-803 21,500 17,200 43,000EN3-804 28,700 23,000 57,400EN3-805 34,000 27,200 68,000EN3-806 40,700 32,500 81,400EN3-808 46,00 36,800 92,000EN3-810 51,500 41,200 103,000EN3-812 59,200 47,300 118,400EN4-801 10,000 8,000 20,000EN4-802 19,800 15,800 39,600EN4-803 26,700 21,300 53,400EN4-804 35,600 28,400 71,200EN4-805 42,200 33,700 84,400EN4-806 50,500 40,400 101,000EN4-808 57,600 46,000 115,200EN4-810 67,200 53,700 134,400EN4-812 80,700 64,500 161,400

CAUTION DO NOT EXCEED RATED CAPACITIES

147

5

1101

-2-1

0

SLINGS

TYPE 6 Type 6 - Return eye (reversed eye) sling is formed by using multiplewidths of webbing held edge to edge. A wear pad is attached onboth sides of the sling body and on both sides of the loop eyes toform a loop eye at each end which is at a right angle to the plane ofthe sling body.

Code No. Vertical Choker Basket Sling Width RE1-802 3,200 2,500 6,400 2RE1-804 6,400 5,000 12,800 4RE1-806 8,600 6,900 17,200 6 RE2-802 6,200 4,900 12,400 2RE2-804 12,200 9,800 24,400 4RE2-806 16,300 13,000 32,600 6RE3-804 16,000 12,800 32,000 4RE3-806 21,500 17,200 43,000 6RE4-806 26,700 21,200 53,400 6

Available in other widths.

CAUTION DO NOT EXCEED RATED CAPACITIES

Stone Handling Slings are made of woven nylon web reinforcedwith special abrasion-resistant facing yarns. This rugged material isdesigned expressly for lifting stone, concrete and building panels.Outstanding properties:• Facing made of abrasive resistant material.• Nylon-backed for strength• Natural untreated web for softness and no color rub-off.• Standard eye size is 12"Note: Stone handling slings available in 4" width only.

Specifications- - Rated Capacities in Lbs.

Type Code No. Vertical Choker Basket

1 SHTC1-704 5,400 4,000 10,800 1 SHTC2-704 9,400 7,000 18,800 2 SHTT1-704 5,400 - 10,800 2 SHTT2-704 9,400 - 18,800

3-4 SHEE1-704 5,400 4,000 10,800 3-4 SHEE2-704 9,400 7,000 18,800 5 SHEN1-704 8,000 6,000 16,000 5 *SHEN2-704 8,000 6,000 16,000

*Note: 2-ply Endless slings (SHEN2-704) have no lap. The ends are butted for freerolling over spreader. Capacities are the same as 1 ply, but both sides are faced withabrasive-resistant materials to give double use.

CAUTION DO NOT EXCEED RATED CAPACITIESSLINGS OR ASSEMBLIES ARE NOT TO BE USED FOR TRANSPORTING PERSONNEL.

Attached Eye Wide-Lift

Body Code Vertical Basket Eye EyeWidth Number Hitch Cap. in Lbs. Length Width

6" WLA1-806 3,000 10" 1" 6" WLA2-806 6,000 10" 1" 8" WLA1-808 3,000 10" 1" 8" WLA2-808 6,000 10" 1" 10" WLA1-810 3,000 12" 1" 10" WLA2-810 6,000 12" 1" 12" WLA1-812 3,000 12" 1" 12" WLA2-812 6,000 12" 1" 16" WLA1-816 5,000 12" 2" 16" WLA2-816 10,000 12" 2" 20" WLA1-820 5,000 18" 2" 20" WLA2-820 10,000 18" 2" 24" WLA1-824 5,000 18" 2" 24" WLA2-824 10,000 18" 2"

CAUTION DO NOT EXCEED RATED CAPACITIESSLINGS OR ASSEMBLIES ARE NOT TO BE USED FOR TRANSPORTING PERSONNEL

Continuous Eye Wide-Lift

Body Code Vertical Basket Eye EyeWidth Number Hitch Cap. in Lbs. Length

6" WL1-806 15,400 9" 1-1/2" 6" WL2-806 28,600 9" 1-1/2" 8" WL1-808 20,400 12" 2" 8" WL2-808 38,000 12" 2" 10" WL1-810 25,600 15" 2-1/2" 10" WL2-810 47,600 15" 2-1/2" 12" WL1-812 30,800 18" 3" 12" WL2-812 57,200 18" 3" 16" WL1-816 38,000 24" 4" 16" WL2-816 61,500 24" 4" 20" WL1-820 45,000 30" 5" 20" WL2-820 63,000 30" 5" 24" WL1-824 52,000 36" 6" 24" WL2-824 70,000 36" 6"

Note: Normal eye length is 1 1/2 times body width.

CAUTION DO NOT EXCEED RATED CAPACITIESSLINGS OR ASSEMBLIES ARE NOT TO BE USED FOR TRANSPORTING PERSONNEL

148

809-

2-10

PORTABLE LIGHT TOWER

The Night-Lite™ PRO features Allmand’s SHO-HD lightingsystem as standard equipment. Featuring 1,250-watt lampsand ballasts, it produces 150,000 lumens per lamps, a 36%increase over the industry standard of 1,000-watt lamps.

SHO-HD FIXTURESSHO-HD (super high output-high definition) parallel lamp fixtures provide over 50% more lumens per fixture than competitive llight towers. An optional Saf-T-Visor™attachement directs previously wasted light onto the worksite.

DimensionsHeight mast lowered . . . . . . . . . . .6 ft.1 in.(1.9m)Height mast raised . . . . . . . . . . . . . . .30 ft. (9.1m)Length with fixtures . . . . . . . . . .13 ft.6 in. (4.0m)Width . . . . . . . . . . . . . . . . . . . . .4 ft.1.5 in. (1.3m)Outrigger width . . . . . . . . . . . . .7 ft.9.5 in. (2.4m)Wheels and tires . . . . . . . . . . . . . . . .13 in. (33cm)

Engine - (Standard)Model . . . . . . . . . . .Kohler KDW 1003, 1,800 rpm

liquid cooled diesel with 12-volt electric startDisplacement . . . . . . . . . . . .54.86 cu. in. (898cc)Alternator . . . . . . . . . . . . . . . . . . .30 amp, 12-voltPower output . . . . . . . . . . . . . .13.4 hp continuousFuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .DieselFuel consumption . . . . . . . . .46 gal./hr. (1.70 L/hr)Fuel capacity . . . . . . . . . . . . . . . .30 gallon (114 L) Oil sump capacity . . . . . . . . . . .5.4 U.S.qt. (5.1 L)

Low oil pressure, high temperature automaticshutoff, glow plug cold start system.

LightingLamps . . .Four (4) 1250 watt metal halide fixtures . . . . . . . . . . . . . . . . . . .5000-watt lighting system

NIGHT-LITE PRO SPECIFICATIONS

ElectricalAlternator . . . . . .7.5kw alternator, 60 Hz, 1 phaseCircuits . . . . . . . . . . . . . . . . .Hard-wired electricalBallast .Easily serviceable, “componentized” assy.Ground rod . . . . . . . . . . . . . . . . . . . . . . .Standard120 volt convenience outlets . . . . . . . . . .Standard

TowerAssembly . . . .30 ft. hvy.-duty three section towerGuide pads . . . . .Self-lubricating nylon wear padsRotation . . . . . . . .360º rotatable from the ground

TrailerFrame . . . . . . . . . . . . . . . . . .Formed, welded steelEnclosure Heavy-duty with 10-gauge side panels,

12-gauge hood and lockable lift-up doorsFenders .Dent and rust resistant rotational moldedHitch . . . . . . . .Adjustable height, 2 in. ball couplerLights . . . . . . . . . . . . . . . . .Stop, turn and runningForklift pockets . . . . . . . . . . . . . . . . . . . .Standard

StabilizersThree-point outrigger designTower center-mounted between two retractable rear

outriggers and tongue jack Remains operational in wind gusts up to 65 mph

Available OptionsSaf-T-Visor™ Ground RodLSC100 auto light sequence Electric WinchSound attention package Arctic package220 VAC twist lock receptacle CSA models International models 8kw generator

CAPTIVE TOWER LATCHCaptive latch on tower support and outriggers eliminates potential for lost pins.

FORKLIFT POCKETSForklift pockets and lifting eye alloweasy loading and unloading of up to12 units on a flatbed truck.

HEAVY-DUTY ENCLOSURES30-gallon molded polyethylene fueltank reduces the chance of contamina-tion from rust and corrosion associat-ed with metal. Provides approximately65 hours of continuous operation.

ENGINE-GENERATOREngine-generator package includes an1,800-rpm liquid-cooled diesel enginecoupled to a 6kw generator.

149

5

1057

-2-1

0

HEATERS

TRADESMAN PFA HEATERS

L.B.WHITE TRADESMAN portable forced air (PFA) heaters offer the best value in economical, high-volumeconstruction heating.

All Tradesman and Tradesman Ultra PFA heaters are engineered to deliver high heat output with the ability tomove large volumes of air - plus solid state electronic ignition for sure starts, thermostatic controls and built-insafety features.

• Models ranging from 100,000 to 400,000 Btu/h.• 99.97%+ fuel efficient direct-fire design.• Solid state electronic ignition.• Weather resistant Tri-Shield finish.• Service Saver™ diagnostic monitoring (Ultra models).• Thermostatic control.• Propane or natural gas.• CSA Certification - United States.

Model Tradesman Tradesman Tradesman Tradesman Tradesman Tradesman Tradesman100 155 155 Ultra 155N 155N Ultra 400 400 Ultra

Heat RatingMax Input (Btu/h) 100,000 155,000 155,000 155,000 155,000 400,000 400,000Min. Input (variable)(Btu/h) 50,000 - - - - - -

Configurations AvailableIgnition Type Piezo Piezo Piezo Piezo Piezo Piezo Piezo

Heated Air OutputHeated Air Output (CFM) 350 625 625 625 625 1582 1582

Control SystemService Saver - - Yes - Yes - YesStandard Yes Yes Yes Yes Yes Yes Yes

Fuel Consumption (max)LPG (lbs./hr.) 2.3 to 4.6 7.2 7.2 - - 18.5 18.5NG (cu.ft./hr.) - - - 155.0 155.0 - -

Inlet Gas PressureLPG min/max (W.C.) 11.0 11.0 11.0 - - 111.0 111.0NG (W.C.) - - - 4.6 4.6 (4 PSIG) (4 PSIG)

Electrical SupplyAmps (Starting/cont.oper.) 2.0 2.4 2.4 2.4 2.4 3.0 3.0Electrical Requirements 115 / 115 / 115 / 115 / 115 / 115 / 115 /(Volts/Hz/Phase) 60 / 1 60 / 1 60 / 1 60 / 1 60 / 1 60 / 1 60 / 1

DimensionsHeight (in.) 14.0 14.0 14.0 14.0 14.0 18.5 18.5Length (in.) 25.3 28.3 28.3 28.3 28.3 33.3 33.3Width (in.) 9.8 11.0 11.0 11.0 11.0 13.5 13.5Net Weight (lbs.) 22.0 28.5 28.5 28.5 28.5 52.0 52.0Shipping Weight (lbs.) 32.0 38.0 38.0 38.0 38.0 68.0 68.0

Additional FeaturesGas Hose (10 ft. - U.S.) Std. Std. Std. Std. Std. Std. Std.Regulator Std. Std. Std. Std. Std. Std. Std.Thermostat (unit mount) - Std. Std. Std. Std. Std. Std.

150

HEATERS

TRADESMAN K KEROSENE HEATERS

For those times when gas may not be available, L.B. WhiteTradesman K Kerosene heaters offer the ultimate in efficient,portable construction heat.

Available in heat outputs from 70,000 to 600,000 Btu/h, allTradesman K portable heaters feature electronic ignition for sure starts, as well as thermostatic control for automatic operation and consistent temperature management.

Key features of the Tradesman K series include:

• Models ranging from 70,000 to 600,000 Btu/h.• 99.97%+ fuel efficient direct-fire design.• 250 to 3300 CFM heated air output.• Dependable, solid state electronic ignition.• Case Material — Baked enamel.• Standard Thermostatic control.

Model Tradesman Tradesman Tradesman TradesmanK 165 K 350 K 600 K 70

Heat RatingMax Input (Btu/h) 165,000 350,000 600,000 70,000

Configurations AvailableIgnition Type Hot Surface Hot Surface Hot Surface Hot Surface

Heated Air OutputHeated Air Output (CFM) 500 1350 3300 250

Fuel Consumption (max)Kerosene or #1 Fuel Oil (gal./hr.) 1.10 2.50 4.0 .52Operating Time / Tankful (hrs.) 12.2 12.0 9.0 9.6Tank Capacity (gal.) 11.25 30.0 36.0 5.0

Pump PressurePump Pressure (PSI) 5 100 110 4

Electrical SupplyAmps (Starting/cont.oper.) 6.0 / 4.5 22.0 / 7.1 22.0 / 11.0 8.0 / 2.5Electrical Requirements 120 / 120 / 120 / 120 /(Volts/Hz/Phase) 60 / 1 60 / 1 60 / 1 60 / 1Spark Plug Gap (in.) 0.075 0.075 0.075 0.055

DimensionsHeight (in.) 25.0 31.0 42.0 15.5Length (in.) 42.0 56.0 76.0 30.0Width (in.) 20.5 30.0 30.0 12.0Net Weight (lbs.) 56.0 180.0 285.0 32.0Shipping Weight (lbs.) 67.0 204.0 390.0 34.0

Additional FeaturesCord Caddy Std. - - -Fuel Gauge Std. - - Std.Handle Std. Std. Std. Std.On/Off Switch Std. Std. Std. Std.Thermostat Std. Std. Std. Std.Wheels Std. Std. Std. -

1057

-3-1

0

151

5

1057

-4-1

0

HEATERS

CONVECTION HEATERS

Ideal for new construction sites or situations whereelectrical power is not readily available, L. B. Whiteconvection heaters offer easy to use, highly efficientheat with no electricity needed.

L. B. White convection heaters include the lightweightWorkman series designed for maximum portability, as well as the heavy-duty Norseman models whichfeature cast iron burners and heavy-gauge steel for maximum durability. All feature a proven design,reliable pilot light ignition and quick componentaccess for easy operation and maintenance.

Key features include:

• Models ranging from 100,000 to 250,000 Btu/h.• 99.97%+ fuel efficient direct-fire design.• Dependable standard or piezo pilot ignition.• Case material — Heavy-gauge painted steel.• Burner type — Cast iron.• Variable Btu/h output.• Propane or natural gas models.• CSA Certification — United States.

Model Norseman Norseman Norseman200 Horizontal 200 Plus 250

Heat RatingMax Input (Btu/h) 200,000 200,000 250,000

Configurations AvailableIgnition Type Pilot Piezo Pilot Pilot

Heated Air OutputHeated Air Output (CFM) 834 850 1041

Fuel Consumption (max)LPG (lbs./hr.) 9.3 9.3 11.6NG (cu.ft./hr.) - - -

Inlet Gas PressureLPG (PSIG) 23.0 23.0 23.0NG (W.C.) - - -

DimensionsHeight (in.) 12.0 24.0 24.0Length (in.) 41.0 18.0 18.0Width (in.) 9.0 17.0 17.0Net Weight (lbs.) 26.0 30.0 32.0Shipping Weight (lbs.) 30.0 36.0 36.0

Additional features - optionsGas Hose 10 ft. - U.S. Std. Std. Std.Regulator Std. Std. Std.

Certifications:CSA - U.S. No Yes No

152

620-

1-10

MATERIAL LIFTS

153

SUPERLIFT™ ADVANTAGEThe Material Handlerwith the largest selection ofload handling attachmentsand accessories anywhere.

The Genie SuperLift Advantage is a package of options you select to designthe Superlift you need and want.....and you get more value for your money.It’s easy as one, two, three:

1. Choose the base and the mast – either Standard Base with five different lifting heights – or Straddle Base with three differentlifting heights.

2. Choose the load handling attachments you need.

Options and Accessories:• Interchangeable load handling attachments handle a large variety of work loads.• A safety brake is optional on all units.• Rear transport wheel assembly.

Standard Features:• One speed winch.• Patented telescoping mast system.• Heavy-duty design for compactness, safety, strength and rigidity.• Quick set-up requires no tools and is ready to work in seconds.• Easy to load.• In the stored position, roller wheels on the base of the legs allow the unit to be

easily pushed around.• Hold-down bar holds mast assembly in place during transport.

SUPERLIFT™ CONTRACTOR

GENIE® LOAD LIFTER™

GENIE LIFT™There is a Genie Lift™ for everyload. A manually operated material lift for construction and industrial applications.

The hand truck that lifts up to 200 pounds (91kg) to5 feet 7 inches (1.7m).

A manually operatedmaterial lift forconstruction andindustrial applications.An ideal tool forconstruction firms andevery other kind ofcontractor.

The Genie Lift’s improved design provides years of reliable service. It iseasily loaded in any size pickup truck to go wherever you need a lift. Withthree basic models to choose from, the Genie Lift is ideal for all your material handling needs.

Standard Features:• One person can safely and easily lift and move heavy loads.• Designed and constructed of durable yet lightweight aluminum.• Quiet high-speed reversible winch quickly lifts heavy loads.• High strength aircraft quality cable prevents corrosion and fraying.• Cushioned neoprene hand grip for easy handling.• Corrosion resistant – won’t rust.• Beveled aluminum platform for easy loading and unloading.• Accessories are easy to install.• Portable – folds for compact storage and easy transport.• 8-inch non-marking rear wheels are standard.• All models include stair glides for easy handling on stairs.

Options and Accessories:• Load platform.• Boom.• Aluminum ladder – Standard and Straddle Base.• Pneumatic rear wheels - Standard and Straddle Base.• Foot-release brake – Standard and Straddle Base.• Caster Options.

Standard Features:• Durable steel forks.• Hold-down mechanism secures carriage during transport.• Reversible winch handle for easy storage.• Winch operates while ladder is in use or stowed.• Loads easily into a pickup truck for transporting.

These are a few of the thousands of applications:• Shipping/receiving. • Record storage and retrieval.• Transporting appliances. • HVAC installation and repair.• Lifting heavy materials to or • Lifting equipment/computer products

from shelves. in retail stores.• Moving office equipment. • Handling cement bags.• Installing ceiling/wall appliances. • Lifting and moving automotive parts.

Options and Accessories:• Fixed front caster option.• Stabilizer set (standard on SLC-18 and SLC-24).

Options and Accessories:• Pneumatic 8-inch rear wheels for rough terrain.• Field-installed foot brake.• 2-inch non-marking front swivel casters for easy maneuvering with heavy loads.

Standard Features:• Heavy-duty design, yet lightweight and portable.• Quick set-up requires no tools.• Loads easily into a pickup truck for transporting.• Rear transport wheel assembly.• 4-inch front casters and 5-inch rear casters with side brakes are standard.• Hold-down bar holds mast assembly in place during transport.

5

620-

2-10

PERSONNEL LIFTS

154

GENIE AWP™ SUPER SERIES™(Aerial Work Platform)

GENIE RUNABOUT™ GR

GENIE IWP™ SUPER SERIES™(Industrial Work Platform)

Genie Portable Aerial Work Platforms safely reach workingheights of up to 46 ft. 3 in. (14.1m). Choose from compact,rough terrain, standard or wide base models and modelsthat lift one person. All offer quick set-up and excellentmaneuverability. Numerous options include an outreachpackage, power wheel assist, multiple platform options andAC, DC or Airmotor power.

Model AWP Super SeriesPlatform Height 20 ft. 1 in. – 40 ft. 3 in. (6.1 – 12.3m)Lift Capacity 300 – 350 lb. (136 – 159kg)Power AC, DC or AirmotorWeight 655 – 1,130 lb. (297 – 513kg)

The Genie Aerial Work Platform AWP™ can safely lift one personto working heights of up to 46 ft. 3 in. (14.1m). Easilymaneuverable, offers durability and the convenience of quickset-up and operation.

Model IWP Super SeriesPlatform Height 20 ft. 6 in. – 29 ft. 6 in. (6.22 – 9m)Lift Capacity 350 lb. (159kg)Power AC or DC Weight 1,245 - 1,530 lb. (565 - 694kg)

The Genie Industrial Work Platform IWP™ utilizes a revolutionarydesign to provide stable working heights of up to 35 ft. 6 in.(10.8m) without outriggers. Outreach and power wheel assistoptions available.

Model Runabout™ GRPlatform Height 11 ft. 5 in. - 19 ft. 11 in. (3.48 - 6.07m)Lift Capacity 350 - 500 lb. (159 - 227kg)Power DC Weight 1,581 - 2,451 lb. (717 - 1,112kg)

The Genie Runabout™ fits in tight work areas without outriggers.Elevates to a working height of up to 25 ft. 11 in. (8.07m).Extension deck platform option available.

AWP™GR™

IWP™

620-

5-10

TELESCOPIC STICK BOOMS

Self-Propelled Telescopic Booms

Genie® Telescopic S™ Stick Booms set the industry standard for personnel lifts. With working heights from 46 to 131 feet (14 to 39.9m), articulated jibs on the S-45, S-65, S-85, S-105 and S-125 models, and options including two- and four-wheeldrive, rough terrain packages and multi-power capabilities, we give you just the lift you need.

Specifications

Specifications

Model S™-40 S™-45 S™-60X S™-65Working height 46' 51' 66' 71' Platform height 40' 45' 60' 65' Height - stowed 8' 2" 8' 2" 8' 11" 8' 11"Length - stowed 24' 3" 27' 10" 27' 11" 31' 2"Width 7' 6" 7' 6" 8' 2" 8' 2"Wheelbase 7' 3" 7' 3" 8' 2.5" 8' 2.5"Ground clearance 1' 0.5" 1' 0.5" 1' 2.5" 1' 2.5"Platform length (6'/8') 30"/36" 30"/36" 30"/36" 30"/36"Platform width (6'/8') 72"/96" 72"/96" 72"/96" 72"/96"Horizontal reach 31' 8" 36' 8" 50' 10" 56' 2"Lift capacity 500 lb. 500 lb. 500 - 1000 lb. 500 lb.Turning radius (outside) 15' 8" 15' 8" 18' 2" 18' 2"Turning radius (inside) 6' 8" 6' 8" 7' 9" 7' 9"Turntable rotation 360º 360º 360º 360ºTurntable tailswing 34" 34" 4' 4'Power source Ford DSG 423 4 cylinder gas/LPG 75 hp (56kW)

Deutz D2011L03i 3 cylinder 46 hp (34.3kW)Perkins 404D-22 4 4 cylinder diesel 51 hp (38kw)

Hydraulic tank capacity 45 gal. 45 gal. 45 gal. 45 gal.Fuel tank capacity 20 gal. 20 gal. 40 gal. 40 gal.Weight 12,300 lb. 15,200 lb. 20,570 lb. 22,100 lb.

Model S™-80X S™-85 S™-100 S™-105 S™-120 S™-125Working height 86' 91' 106' 111' 126' 131' 2"Platform height 80' 85' 100' 105' 120' 125' 2"Height - stowed 9' 2" 9' 2" 10' 1" 10' 1" 10' 1" 10' 1"Length - stowed 36' 6" 40' 42' 8" 46' 42' 8" 46' 9" Width 8' 2" 8' 2" 8' 2" 8' 2" 8' 2" 8' 2"Wheelbase 9' 4" 9' 4" 12' 12' 12' 12'Ground clearance 13" 13" 1' 5.5" 1' 5.5" 1' 5.5" 1' 5.5"Platform length (6'/8') 30"/36" 30"/36" 30"/36" 30"/36" 30"/36" 30"/36"Platform width (6'/8') 72"/96" 72"/96" 72"/96" 72"/96" 72"/96" 72"/96"Horizontal reach 71' 6" 76' 6" 75' 80' 75' 80'Lift capacity 500 - 1000 lb. 500 lb. 750 lb. 500 lb. 750 lb. 500 lb.Turning radius (outside) 21' 6" 21' 6" 21' 7" 21' 7" 22' 2" 22' 2"Turning radius (inside) 12' 12' 13' 7" 13' 7" 13' 2" 13' 2"Turntable rotation 360º 360º 360º 360º 360º 360ºTurntable tailswing 4'8" 4'8" 5' 6" 5' 6" 5' 6" 5' 6"Power source Deutz TD2011 LO4i 4 cylinder turbo Cummins B3.3T 4 cylinder turbo diesel 80 hp (60kW)

diesel 74 hp (55kW) Deutz TD 2011 L04i 4 cylinder turbo diesel 74 hp (55kW)Perkins 804D-33 4 63 hp (47kw) Perkins 804-33T 4 cylinder turbo diesel 83 hp (62kW) Continental TME27 4 cylinder gas/LPG

74 hp (55kW)Hydraulic tank capacity 40 gal. 40 gal. 55 gal. 55 gal. 55 gal. 55 gal.Fuel tank capacity 35 gal. 35 gal. 40 gal. 40 gal. 40 gal. 40 gal.Weight 2WD/4WD 35,460/35,560 lb. 37,900/38,000 lb. 39,700 lb. 40,000 lb. 44,340 lb. 44,640 lb.

155

5

Model Z-45/25 RT Z-45/25J RT Z-60/34 Z-80/60Working height 51' 11" 52' 2" 66' 4" 84'

Platform height 45' 11" 46' 2" 60' 4" 78'

Height - stowed 6' 11" 6' 11" 8' 10" 9' 10"Length - stowed 18' 3" 22' 5" 26' 9" 37'Length - transport 30'Width 7' 6" 7' 6" 8' 1" 8' 2"Wheelbase 6' 8" 6' 8" 8' 3" 9' 4'Ground clearance 1' 3.5" 1' 3.5" 1' 4" 12"Platform length (6'/8' platform) 30" 30" 30"/36" 30"/36"Platform width (6'/8' platform) 72" 72" 72"/96" 72"/96"Horizontal reach 25' 25' 1" 36' 3" 60'Up and over clearance 23' 6" 24' 2" 27' 29'Lift capacity 500 lb. 500 lb. 500 lb. 500 lb.Turning radius

Outside (4WS/2WS) 14' 9" 14' 9" 19' 11" 15'/24' 6"Inside (4WS/2WS) 5' 6" 5' 6" 10' 7'/15'

Turntable rotation 355º non-continuous 355º non-continuous 360º continuous 360º continuousTailswing zero zero zero 3' 10" (elevated position)Power source Ford DSG-423 4 cylinder gas/LPG 75 hp (56kW) Deutz TD 2011 L04i 4 cylinder

Deutz D2011L03i 3 cylinder diesel 48 hp (35.8kW diesel 78 hp (58kW) Perkins 404D-22 4 cylinder diesel 51 hp (38kW) Perkins 804D-33 4 cylinder

diesel 63 hp (47kW)Continental TME27 4 cylinder

gas/LPG 74 hp (55kW) Drive speed - stowed 5.0 mph 5.0 mph 3.0 mph 3.0 mphDrive speed - raised 0.61 mph 0.61 mph 0.68 mph 0.68 mphLift speed to full height 45 sec 45 sec 76 secControls 12V DC proportional 12V DC proportional 12V DC proportional 12V DC proportionalAuxiliary power unit 12V DC 12V DC 12V DC 12V DCPlatform rotations 180º 160º 180º 160ºTires 355/55 D625 355/55 D625 385/65 D19.5, 12 ply 18-625 NHSGradeability (2WD/4WD) 30%/45% 30%/45% 25%/40% 30%/45%Hydraulic tank capacity 24 gal. 24 gal. 45 gal. 45 gal.Fuel tank capacity 17 gal. 17 gal. 20 gal. 35 gal.Weight (2WD/4WD) 13,675 lb./13,875 lb. 14,300 lb./14,500 lb. 22,520 lb. 35,900 lb./37,500 lb.

620-

6-10

ARTICULATING BOOMS

Genie® Articulating Z TM

Booms provide the ultimatein lifting versatility, withup, out and over positioningcapabilities. Many optionsare available, including:two- and four-wheel drive; a rough terrain package;narrow access models thatroll through standard double doorways; gas/LPG,diesel, electric and bi-fuelcapabilities. Choose frommodels with workingheights from 52' 2" to 86';horizontal reach from25' to 60'.

Specifications

156

620-

7-10

TRAILER MOUNTED BOOMS

For over 30 years Genie® hasbeen dedicated to designingand manufacturing the bestlifting equipment in the industry. Our Trailer MountedZ-Booms demonstrate thisdedication by setting newstandards for quality, valueand innovation in the trailermounted boom market.

TZ™-34/20 TZ™-50

Model TZ™™-34/20Working height 40'Platform height 34'Height - stowed 76.5"Length - stowed 18' 5"Width - stowed 4' 9.1"Ground clearance 9.5"Platform length 26.8"Platform width 44"Entry height - extended 6.4"Outreach - working 18' 4"Outrigger footprint - length 8' 4"Outrigger footprint - width 9' 4"Leveling capability

hydraulic outriggers 11ºLift capacity - ANSI, CSA

standard platform 500 lb.platform rotation option 460 lb.

Turntable rotation 359º non-continuousTowing speed rating 60 mphPower sources 24V DCAC wiring to platform standardTongue weight 315 lb.Tire size ST 205x75 R15Surge brakes standardParking brake standardWeight 3,155 lb.

SpecificationsModel TZ™™-50Working height 55' 6"Platform height 49' 6"Height - stowed 82"Length - stowed 23' 6"Width - stowed 5' 6"Ground clearance 10"Platform length 26.8"Platform width 44"Entry height - extended 1' 8"Outreach - working 29' 2"Outrigger footprint - length 14' 4"Outrigger footprint - width 14' 4"Leveling capability

hydraulic outriggers 10ºLift capacity - ANSI, CSA

standard platform 500 lb.platform rotation option 500 lb.

Turntable rotation 359º non-continuousTowing speed rating 60 mphPower sources 24V DC four 6V 225 Ah batteriesAC wiring to platform standardTongue weight 400 lb.Tire size 215 R14CSurge brakes standardParking brake standardWeight (ANSI, CE/CSA) 4,400 lb./4,464 lb.

Specifications

157

5

386-

2-10

MESSAGE SIGNS / ARROW PANELS

Silent Sentinel Silent Messenger II Silent Messenger IIIArrow Panels Dynamic Message Signs Dynamic Message Signs15 or 25 Lamps 92" x 54" Sign Panel 70" x 42" Sign Panel

Size C Panel (96" x 48") (234cm x 137cm) (178cm x 107cm)(122cm x 244cm) Full Matrix Display Full Matrix Display

Size B Panel (60" x 30") (48 x 27 pixels) (48 x 27 pixels)(76cm x 152cm)

• Three sizes to suit your requirements and applications.• On screen prompts in English, French, Spanish, German and Dutch.• Full matrix display with graphics capability.• Built-in weatherproof control console.• Pre-wired for cellular remote control.• Polyethylene fenders and battery compartments.• Automatic fault detection and error correction.• Torsion-type axle for a smooth, stable ride.• Advanced solar energy management and control system.

SILENT SENTINEL SPECIFICATIONSLength Overall ...........100 in. (254cm) Operating Voltage ....................12 Volts DCWidth Overall ..............96 in. (244cm) Number of Batteries .......................Two (2)*Height Operating .......134 in. (340cm) Battery Bank Capacity ......300 Amp Hours*Weight.....................1180 lbs. (535kg) *Upgradable to 4 batteries (600 Amp hours)

Silent Sentinel MODELS: AB-0515 AB-0715

AB-0525 AB-072515 or 25 Lamp Arrow Panel50 or 75 Watt Solar Array

SILENT MESSENGER SPECIFICATIONSLength Overall .........180 in. (457cm) Operating Voltage .........................12 Volts DCWidth Overall.............92 in. (234cm) Number of Batteries .........................Eight (8)*Height Operating .....162 in. (412cm) Battery Bank Capacity ........1200 Amp Hours*Weight.................2690 lbs. (1220kg) *Upgradable to12 batteries (1800 Amp Hours)

• Two sizes to suit your requirements and applications.• Built-in weatherproof control console.• Pre-wired for cellular remote control.• Polyethylene fenders and battery compartments.• Automatic fault detection and error correction.• Torsion-type axle for a smooth, stable ride.• Advanced solar energy management and control system.

SILENT MESSENGER – Portable, Changeable Message Signs – Solar Powered

Silent MessengerMODELS: MB-2248 225 Watt

MB-3048 300 WattMB-3748 375 WattMB-4048 450 Watt

SILENT SENTINEL – Arrow Boards – Solar Powered

Truck Mounted Message Signs and Arrow Boards also available

158

1953

-12-

10

HAND TOOLS / WHEELBARROWS

A

Handle Head / Pk. /Key Item No. Brand Length Blade Size Cube Wt. Lbs. DescriptionA BMTLR Jackson 48" 9-1/2" x 12" 3.54 6/26 Round Point Shovel • 48" Long Handle • Roll Back StepB BMTLS Jackson 48" 10' x 12" 3.05 6/24.3 Square Point shovel • 48" Long Handle • Roll Back Step

Blade Size Pk. /Key Item No. Brand Head Width Cube Wt. Lbs. Description

C 1880600 Pony® 17-7/8" 2.7 6/27.6 Heavy-duty road rake. 14 teeth. 66" handle.D 1935900 Kodiak® 22" 2.2 12/30.0 22-tine spring brace rake. 54" handle.

Handle Head Eye Pk. /Key Item No. Brand Length Weight Size Wt. Lbs. DescriptionE 1199100 Jackson 32"/36" Hickory 10 lb. 1' x1-3/8" 2/22.5 10 lb. Double face sledge hammer.

Pk. /Key Item No. Brand Capacity Cube Wt. Lbs. Description

F M11T22 Jackson 6 cu. ft. 9.2 1/63.0 Contractor Wheelborrow. Folded Seamless steel tray with wire reinforced trim makes the strongest wheelbarrow avaialble. Steel front tray braces, “H” brace, cross strips and leg stabilizers. 16" wheel assembly with pneumatic 2-ply tire with oilube bearing.

G M11FFBB Jackson 5-3/4 cu. ft. 6.0 1/65 Folded steel tray. H-brace, steel cross strips and leg stabilizers. 16" wheel assembly with solid tire and ball bearings. Extra-large, moisture-resistant, strong hardwood handles for heavy use.

Pk. /Key Item No. Brand Cube Wt. Lbs. DescriptionH FFTCC True-Temper 0.59 3/24.0 Flat-Free solid tire.I FFTKBCC Jackson 0.59 3/24.0 Solid knobby tire, flat-free.

F

I

D

C

B

G

E

H

159

5

1996

-10-

10

160

SAFETY GLASSES

Meets the requirements of ANSI Z87.1Ultra-cool and ultra-lightweight polycarbonate frames ensure worker acceptance

Wraparound design fits snugly for total optical protection. Lens offers 99% UV protectionFeatures a 9.75-base spherical polycarbonate lens

THE ORIGINAL ECONOMY Same great style and fit withan uncoated lens. Provides agreat low cost alternative.

• Lightweight contemporary design• 6.75 base curve single lens• Convenient spectacle strap included

• Wraparound design for optimal coverage• High-gloss finish• 9.5 base curve single lens

• Frameless lightweight design• No-brow design increases upward and peripheral vision• 7 base single lens• Rubber tip temple for extra hold• Adjustable nose pad for comfortable fit

• Frameless wraparound design• 6.5 base curve single lens• Adjustable nose pad for comfortable fit

Lens Hard Coating Protective coating on lens that is resistant to scratches in abrasive environments to extend lens lifeCoatings Anti-Fog Coating Provides resistance to moisture in high humidity environments and occurrences of temperature shiftsGuide: UV Protection Absorbs more than 99% of harmful ultraviolet radiation.

• All ERB Safety Eyewear is manufactured under the ISO 9001/2000 Quality System• All ERB Eyewear is protected with a hardcoat finish to provide scratch resistance unless otherwise stated• All ERB Safety Eyewear meet the requirements of ANSI Z87.1 - High Impact• All ERB Eyewear have polycarbonate lenses that offer 99% UV protection

Item # Temple Frame Lens15280 Smoke Smoke Smoke15282 Smoke Silver Silver Mirror15286 Smoke Gold Gold Mirror15284 Clear Clear Clear15285 Amber Amber Amber15287 Blue Blue Blue Mirror

Item # Temple Frame Lens15301 Smoke Smoke Smoke15300 Clear Clear Clear

Available in 2 choices:

Item # Frame Lens16855 Black Clear16856 Black Smoke

Item # Temple Frame Lens16501 Pewter Pewter Smoke16500 Blue Blue Smoke16505 Smoke Pewter Silver Mirror16504 Smoke Silver In/Out Mirror16506 Smoke Blue Blue Mirror

Item # Temple Lens16651 Black Smoke

Item # Temple Lens15420 Black/Silver Clear15423 Black/Silver Silver Mirror15422 Black/Silver Amber

2863

-1-1

0

SAFETY HARNESS /LANYARD / LIFELINE

3M™ Safewaze™ HARNESSES

SAFELIGHT LANYARDS • Polyester web.• SafeStop Shock Absorber with clear UV Resistant Plastic.

• Lightweight for improved work function and comfort.

209510 - 3FT. SHOCK LANYARD 209512 - 6FT. SHOCK LANYARD 209550 - DOUBLE 6FT SHOCK WEB

LANYARD 100% TIE-OFF

3M™ Safewaze™ LIFELINE

3M™ Safewaze™ LANYARDS

209512

209550

1711

APACHE • Must be used in conjunctionwith the 400 lb. ShockAbsorbing Lanyard.

• Full body harness to support larger workers.

• 4" stationary back pad andshoulder pads.

• Back D-ring. 1710 - APACHE HARNESS -

(S, M, L, XL, XXL, XXXL) 1711 - APACHE HARNESS -

(S, M, L, XL, XXL, XXXL)WAIST D-RINGS

EVOLUTION • Back D-ring, side D-ring.• All quick connect connectors.

7511 - AIRFLEX COMFORT - (S, M, L, XL, XXL)

7511

WORKSAFE with BACK PAD • Specially designed for positioning applications.

1311 - BODY HARNESS W/ BACK PAD - (S, M, L, XL, XXL)

SAFELIGHT • Universal size.• Back D-ring and optional front D-ring.10910 - UNIVERSAL HARNESS10950 - UNIVERSAL HARNESS -

GROMMET LEG STRAPS (XS ECONOMY ALSO AVAILABLE)

10951 - UNIVERSAL HARNESS -GROMMET LEG STRAPS AND WAIST D-RINGS (XS ECONOMY ALSO AVAILABLE)

5/8" LIFELINE with LOCKING SNAP HOOK

• Double-locking snaphook on one end. and back spliced on the other end.

• Constructed of 5/8" SafeCom Polydac blended rope.• 100' length.• Low Elasticity. 0221-100 - 5/8" LIFELINE W/ LOCKING SNAP

10910

10950

1311

Compliant fall protection and emergency rescue systems helpprevent serious injury during fall arrest. Users must read andunderstand the User Instructions provided with the productand be properly trained by their employer prior to use perOSHA 1910.66 and 1926.503 or applicable local standards.Misuse or failure to follow warnings and instructions mayresult in serious personal injury or death. For proper use, see supervisor, User Instructions, or call Technical Serviceat 1-800-560-1094.

! WARNING Fall Protection Products

161

5

V7-

05

USEFUL INFORMATION

English standard measures of lengthMEASURES OF LENGTH

1 mile = 1760 yards = 5280 feet.1 yard = 3 feet = 36 inches.1 foot = 12 inches.The following measures of length are also used occasionally:1 mil=0.001 inch. 1 fathom = 2 yards = 6 feet1 rod = 5.5 yards = 16.5 feet. 1 hand = 4 inches. 1 span = 9 inches

SURVEYOR’S MEASURE1 mile = 8 furlongs = 80 chains.1 furlong = 10 chains = 220 yards.1 chain = 4 rods = 22 yards = 66 feet = 100 links.1 link = 7.92 inches.

SQUARE MEASURE1 square mile = 640 acres = 6400 square chains.1 acre = 10 square chains = 4840 square yards = 43,560 square feet.1 square chain = 16 square rods = 484 square yards = 4356 square feet.1 square rod = 30.25 square yards = 272.25 square feet = 625 square links.1 square yard = 9 square feet.1 square foot = 144 square inches.An acre is equal to a square, the side of which is 208.7 feet.

English standard measures of volumeCUBIC MEASURE

1 cubic yard = 27 cubic feet.1 cubic foot = 1728 cubic inches.The following measures are also used for wood and masonry:1 cord of wood = 4 x 4 x 8 feet = 128 cubic feet.1 perch of masonry = 16½ x 1½ x 1 foot = 24¾ cubic feet.

DRY MEASURE1 bushel (U.S. or Winchester struck bushel) = 1.2445 cubic foot = 2150.42

cubic inches.1 bushel = 4 pecks = 32 quarts = 64 pints.1 peck = 8 quarts = 16 pints.1 quart = 2 pints.1 heaped bushel = 1¼ struck bushels.1 cubic foot = 0.8036 struck bushel.1 British Imperial bushel = 8 Imperial gallons = 1.2837 cubic foot = 2218.19

cubic inches.LIQUID MEASURE

1 U.S.gallon = 0.1337 cubic foot = 231 cubic inches = 4 quarts = 8 pints.1 quart = 2 pints = 8 gills.1 pint = 4 gills.1 British Imperial gallon = 1.2003 U.S. gallon = 277.27 cubic inches.1 cubic foot = 7.48 U.S. gallons.

English standard measures of weightAVOIRDUPOIS OR COMMERCIAL WEIGHT

1 gross or long ton = 2240 pounds.1 net or short ton = 2000 pounds.1 pound = 16 ounces = 7000 grains.1 ounce = 16 drachms = 437.5 grains.

CIRCULAR AND ANGULAR MEASURE60 seconds (��) = 1 minute (�)60 minutes = 1 degree (°)360 degrees = 1 circumference (C).

Metric system of measurementsMEASURES OF LENGTH

10 millimeters (mm) = 1 centimeter (cm.).10 centimeters = 1 decimeter (dm.).10 decimeters = 1 meter (m)1000 meters = 1 kilometer (Km.)

SQUARE MEASURE1000 square millimeters (mm.²) = 1 square centimeter (cm.²).100 square centimeters = 1 square decimeter (dm.²).100 square decimeters = 1 square meter (m.²).

SURVEYOR’S SQUARE MEASURE100 square meters (m.²) = 1 are (ar.).100 ares = 1 hectare (har.).100 hectares = 1 square kilometer (Km.²).

CUBIC MEASURE1000 cubic millimeters (mm.³) = 1 cubic centimeter (cm.³).1000 cubic centimeters = 1 cubic decimeter (dm.³).1000 cubic decimeters = 1 cubic meter m.³).

DRY AND LIQUID MEASURE10 millimeters (ml.) = 1 centiliter (cL.).10 centiliters = 1 deciliter (dL.).10 deciliters = 1 liter (L.).100 liters = 1 hectoliter (HL.).1 liter = 1 cubic decimeter = The volume of 1 kilogram of pure water at

a temperature of 39.2 degrees F.

MEASURES OF WEIGHT10 milligrams (mg.) = 1 centigram (cg.).10 centigrams = 1 decigram (dg.).10 decigrams = 1 gram (g.).10 grams = 1 decagram (Dg.).10 decagrams = 1 hectogram (Hg.).10 hectograms = 1 kilogram (Kg.).1000 kilograms = 1 (metric) ton (T.).

Miscellaneous informationTo find the diameter of a circle multiply the circumference by .31831.To find the circumference of a circle multiply the diameter by 3.1416.To find the area of a circle multiply the square of the diameter by .7854.To find the surface of a ball multiply the square of the diameter

by 3.1416.To find the side of an equal square multiply the diameter by .8862.To find the cubic inches in a ball multiply the cube of the dia. by .5236.To double the diameter of a pipe increase its capacity four times.Double riveting is from 16 to 20 per cent stronger than single.One cubic foot of anthracite coal weighs about 53 pounds.One cubic foot of bituminous coal weighs from 47 to 50 pounds.One ton of coal is equivalent to two cords of wood for

steam purposes.A gallon of water (U. S. standard) weighs 8-1/3 pounds and contains

231 cubic inches.A standard or Winchester bushel contains 2150.4 cubic inches.There are 9 square feet of heating surface to each square foot of

grate surface.A cubic foot of water contains 7½ gallons, 1728 cubic inches and

weighs 62½ pounds.Each nominal horse power of a boiler requires 30 to 35 pounds of

water per hour.A horse power is equivalent to raising 33,000 pounds 1-foot per

minute or 550 pounds 1-foot per second.The average consumption of coal for steam boilers is 12 pounds per

hour for each square foot of grate surface.To find the pressure in pounds per square inch of a column of

water multiply the height of the column in feet by .434.Steam rising from water at its boiling point (212 degrees) has a

pressure equal to the atmosphere (14.7 pounds to the square inch).To evaporate one cubic foot of water requires the consumption of

7½ pounds of ordinary coal, or about 1-pound of coal to 1-gallon of water.The right amount of water for cement mixtures of varying strength is

shown in the following table:Correct amount of water Water perCement Sand Gravel Sack of Cement1 sack 1¼ cu.ft. 2½ cu.ft. 5 to 5½ gal.1 sack 1½ cu.ft. 3 cu.ft. 5½ to 6 gal.1 sack 2 cu.ft. 3 cu.ft. 5¾ to 6¼ gal.1 sack 2 cu.ft. 4 cu.ft. 6 to 6½ gal.1 sack 2½ cu.ft. 5 cu.ft. 7¼ to 7¾ gal.1 sack 3 cu.ft. 6 cu.ft. 8¼ to 8¾ gal.

Below is a table which shows that improper quantities of water wastesthe strength of cement.Not enough water

10% too little water wastes 27% of the cement strength.6% too little water wastes 10% of the cement strength.

Too much water.7% too much water wastes 10% of the current strength.

12% too much water wastes 20% of the cement strength.18% too much water wastes 30% of the cement strength.25% too much water wastes 40% of the cement strength.31% too much water wastes 50% of the cement strength.42% too much water wastes 60% of the cement strength.63% too much water wastes 70% of the cement strength.

Properties of circlesDiameter being given, to find the circumference, multiply diameter

by 3.1416.Diameter given, to find area, square the diameter and multiply the

product by .7854, or multiply ½ the diameter by ½ the circumference.Area given, to find the diameter, divide the area by .7854 and extract

the square root of the quotient.Diameter given, to find side of a square containing same area,

multiply the diameter by .8862.

162

163

ExcavatorsWheel LoadersMotor Graders

Crawler DozersTrack Loaders

Articulating TrucksCompactors

Ground Engagement ToolsSign Stands

Safety ConesTrench Boxes

Heavy Equipment 6

Incorporating the Virginia Track & Equipment platformallows us to offer a full range of heavy equipment rentals,

sales, services and parts to complement our existing compact construction equipment

and supply business.

1928

-2-1

0

164

EXCAVATORS

PC200-8PC200LC-8HORSEPOWERGross: 155 HP (116kW) @ 2000 rpmNet:148 HP (110kW) @ 2000 rpmOPERATING WEIGHTPC200-8: 43,540– 44,110 lbs. (19750– 20010kg)PC200LC-8:46,080– 47,260 lbs. (20900– 21437kg)

PC228USLC-3With Tier 3 EngineFLYWHEEL HORSEPOWER148 HP (110kW) @ 2000 rpmOPERATING WEIGHT49,900–51,110 lbs. (22630–23180kg)BUCKET CAPACITY0.66–1.57 yd.3 (0.50–1.2m3)

PC200LC-8Thumb SpecificationNET HORSEPOWER148 HP (110kW) @ 2000 rpmOPERATING WEIGHT51,199 – 53,115 lbs. (23220 – 24090kg)BUCKET CAPACITY0.66-1.57 yd.3 (0.50-1.20m3)

PC130-8NET HORSEPOWER92 HP (68kW) @ 2200 rpmOPERATING WEIGHT27,700 lbs. (12560kg)BUCKET CAPACITY0.24–0.78 yd.3 (0.18–0.6m3)

PC160LC-8NET HORSEPOWER115 HP (86kW) @ 2200 rpmOPERATING WEIGHT36,770–37,740 lbs. (16680–17120kg)BUCKET CAPACITY0.48–1.24 yd.3 (0.37–0.95m3)

PC160LC-7With Tier 3 EngineFLYWHEEL HORSEPOWER115 HP (86kW) @ 2200 rpmOPERATING WEIGHT36,640– 37,790 lbs. (16620– 17140kg)BUCKET CAPACITY0.48–1.24 yd.3 (0.37–0.95m3)

EXCAVATORS12 METRIC TONS

to

30 METRIC TONS

1928

-1-1

0

165

WHEEL LOADERS

FULL SIZE

WHEEL LOADERS

AND

TOOL CARRIERS

WA200-6NET HORSEPOWER126 HP (94kW) @ 2000 rpmOPERATING WEIGHT23,160 - 23,733 lbs. (10505 - 10765kg)BUCKET CAPACITY2.2 - 3.1 yd.3 (1.7 - 2.4m3)

WA200PZ-6NET HORSEPOWER126 HP (94kW) @ 2000 rpmOPERATING WEIGHT25,275 - 25,420 lbs. (11465 - 11530kg)BUCKET CAPACITY2.5 - 2.75 yd.3 (1.9 - 2.1m3)

WA250PZ-6NET HORSEPOWER138 HP (103kW) @ 2000 rpmOPERATING WEIGHT26,808 - 27,778 lbs. (12160 - 12600kg)BUCKET CAPACITY2.5 - 3.0 yd.3 (1.9 - 2.3m3)

WA250-6NET HORSEPOWER138 HP (103kW) @ 2000 rpmOPERATING WEIGHT25,441 - 25,904 lbs. (11540 - 11750kg)BUCKET CAPACITY2.5 - 3.5 yd 3 (1.9 - 2.7m3)

WA320-6NET HORSEPOWER 167 HP (125kW) @ 2000 rpmOPERATING WEIGHT31,590- 32,080 lbs. (14330 - 14550kg)BUCKET CAPACITY3.0-4.2 yd.3 (2.3–3.2m3)

WA320PZ-6NET HORSEPOWER167 HP (125kW) @ 2000 rpmOPERATING WEIGHT32,480- 33,900 lbs. (14730- 15380kg)BUCKET CAPACITY3.25 - 3.50 yd.3 (2.5 - 2.7m3)

6

Dimensions 12H 120H 140H

1101

-4-1

0

166

MOTOR GRADERS

12HOperating weights (approximate)

on front wheels 7,702 lbs.on rear wheels 21,128 lbs.total machine 28,830 lbs.

120HOperating weights (approximate)

on front wheels 6,976 lbs.on rear wheels 18,064 lbs.total machine 25,040 lbs.

140HGross vehicle weight

bass 29,878 lbs.max. 32,321 lbs.

A

B

C E

F

G

H I

D

A. Width -tire center lines 6' 10" 6'9" 6'9"B. Width - outside front tires 7'11" 7'11" 8'1"C. Width - outside rear tires 8'0" 8'0" 8'0"D. Height - top of cab 10'2" 10'2" 10'3"E. Length - counterweight to ripper 32'10" 31'8" 32'10"F. Length - front tire to rear of machine 27'9" 26'9" 27'10"G. Length - front axle to mid tandem 20'0" 19'3" 20'11"H. Length - between tandem axles 5'0" 4'11" 5'0"I. Length - front axle to moldboard 8'5" 8'6" 9'5"

D3 Net power (SAE J1349) 74 hpWeightsOperating weight – XL 17,185 lbs.Operating weight – LGP 17,842 lbs.

D4 Net power (SAE J1349) 84 hpWeightsOperating weight – XL 17,961 lbs.Operating weight – LGP 18,742 lbs.

D5 Net power (SAE J1349) 96 hpWeightsOperating weight – XL

20,741 lbs.Operating weight – LGP

21,347 lbs.

Dimensions D3K D4K D5K

Dimensions D6K XL LGP

1101

-5-1

0

167

CRAWLER DOZERS

Small and Medium Dozers

A

B

C

5

F

G

HI

D

1J

K

AB

C

E

6

G

H

ID

F

A Track gauge 70 in. 79 in.

B Width of tractor with the following attachments:Standard shoes without blade Standard shoes with VPAT blade angled 25° Standard shoes with foldable blade in transport position

92 in. 111 in. 92 in.

109 in. 123 in. 109 in.

C Machine height from tip of grouser with the following equipment:ROPS canopy ROPS cab

116 in. 116 in.

116 in. 116 in.

D Drawbar height (center of clevis) from ground face of shoes 19 in. 19 in.

E Length of track on ground 104 in. 104 in.

F Length of basic tractor (with C-Frame) With the following attachments, add to basic tractor length:

Drawbar Ripper PA50 winch VPAT blades, straight VPAT blade, angled 25°

166 in.

13 in. 45 in. 25 in. 18 in. 44 in.

166 in.

13 in. 45 in. 25 in. 18 in. 46 in.

G Height over stack from tip of grouser 115 in. 115 in.

H Height of grouser 2 in. 2 in.

I Ground clearance from ground face of shoe (per SAE J1234) 14 in. 14 in.

XL LGP XL LGP XL LGP LGP w/ 30" shoes

A Track gauge 58.9" 67.9" 61" 67.9" 63" 68.9" 73.2"B Width of tractor (std shoes, no blade) 74.8" 92.9" 79.1" 92.9" 83.1" 94.9" 103.5"C Overall length (w/blade) 168" 167.6" 168.3" 168" 170.1" 169.1" 169.1"D Length of basic tractor (w/o blade) 128.9" 128.9" 128.9" 128.9" 128.5" 128.5" 128.5"E Tractor height 108.8" 108.8" 108.8" 108.8" 109" 109" 109"F Ground clearance 13" 13" 13" 13" 13" 13" 13"BLADE XL Intermediate LGP XL Intermediate LGP XL Intermediate LGPG Blade width 104.2" 115" 124" 109.5" (115" 123.9" 109.5" 115" 126.7"H Blade height 35.8" 33.9" 33.8" 39.8" 33.9" 35.8" 42.2" 39.8" 39.8I Blade lift height 28.7" 29.3" 28.7" 29.3" 29.3" 27.9" 30.2" 30.2" 30.2"J Digging depth 22.5" 22.5" 22.5" 22.5" 23.2" 23.2" 23.1" 22.5" 22.5"K Blade cutting edge angle, adjustable

Maximum tilt Maximum angle (either side) Blade width at maximum angle Blade capacity (SAE)

52° to 58° 14.5"

25°95.2"

1.99 yd.3

52° to 58° 17.7"

25°105.1"

1.96 yd.3

52° to 58° 17.2"

25°113.1"

2.17 yd.3

52° to 58°15.2"

25°100.1"

2.59 yd.3

52° to 58°17.6"

25°105.1"

1.96 yd.3

52° to 58°17.2"

25°113.1"

2.42 yd.3

52° to 58°15.8"

25°103.8"

2.86 yd.3

52° to 58°17.6"

25°101.1"

2.73 yd.3

52° to 58°17.6"

25°115.8"

2.73 yd.3

Grouser Height: 1.9"

EngineFlywheel Power 125 hpWeightsOperating Weight – XL 28,409 lbs.Operating Weight – LGP 29,690 lbs.

6

1101

-3-1

0

168

TRACK LOADERS

Q R

D

EG

H

F

I

K

P

O

L

N

M

J

Medium Track LoadersFlywheel Power 148 hp (110kW)Operating Weight 34381 lbs. (15595kg)Capacity - General Purpose 2.42 yd.3 (1.85m3)

Large Track LoadersFlywheel Power 189 hp (141kW)Operating Weight 44,577 lbs. (20220kg)Capacity - General Purpose 3.2 yd.3 (2.45m3)

*With general purpose bucket and extra duty teeth.Dimensions vary with bucket. Refer to Operating Specifcations chart.

953 963

A Overall machine width without bucket:with standard tracks with narrow tracks

89.7"85.8"

89.7"85.8"

B Ground clearance 16.3" 18.5"

C Machine height to top of cab 122.2" 131.3"

D Length to front of track 171.7" 187

E Overall machine length* 246.1" 273.3"

F Carry position approach angle 15° 15°

G Digging depth* 5.5" 5.4"

H Maximum rollback at ground 41° 43°

I Maximum rollback at carry position 48° 50°

J Bucket height in carry position 21.6" 18"

K Reach at full lift height and 45° dump* 47" 54"

L Clearance at full lift height and 45° dump* 106" 114.8"

M Maximum rollback, fully raised 56° 52°

N Maximum dump, fully raised Grading angle

55°74°

53°63°

O Height to bucket hinge pin 142.1" 155.1"

P Overall machine height, bucket fully raised 192.2" 212.7"

Q Height to top of seat with headrest 100.7" 109.8"

R Height to top of stack 109.6" 116.3"

A

B

C

222-

22-1

0

169

ARTICULATING TRUCK

25 Ton Articulating Truck

Volvo’s Unique Self-compensatingHydro-mechanical Steering• Powerful and accurate steering for safe

operation and high productivity.Excellent Operator Environment• A spacious and comfortable cab with centrally positioned

operator contributes to high productivity throughout the shift.• Ergonomically positioned controls, air-conditioning, air sus-

pension seat with tilt/telescopic steering wheel, wide angleforward view for reduced operator fatigue and high safety.

Heavy-Duty Axles• Purpose built with 100% dog

clutch type diff-lock.

Exhaust Brake and Retarders• Easy to operate powerful

retardation systemreduces wear and operating cost.

6x4 and 6x6 with Five Operating Modes• Easy to use drive combinations

for every type of operating condition, reduces fuel consumption,driveline and tire wear and increases off-road mobility.

• Automatic Traction Control (ATC) simplifies operation, promoteslonger tire life and reduced fuel consumption.

Volvo Drive Train• Correctly matched Volvo-designed components,

specifically developed for hauler applications. Lowpower losses and long service life.

• 6-speed transmission gives smooth shifting and highpower at all times.

State-of-the-Art Hydraulic System• Variable displacement piston pumps

consume power only when required.

Purpose-built dropbox• Proven in-line drop-box provides excellent ground

clearance, gives stability and low internal power losses.

Serviceability• No daily or weekly greasing.

Swing Down FrontService Platform• Grouped engine fil-

ters and remotemounted drainsreduce service time.Contronic Systemelectronicallymonitors fluid levels and systems for ease of serviceand troubleshooting.

Maintenance Free Suspensions• The straddle mounted bogie beam gives large

wheel movement and low frame stress. Lowpivot point enhances stability.

• Front axle has independent wheel movementvia a 3-point mounting system.

Frames and Chassis• Box type design frames provides strong, weight optimized,

high quality frames for long service life.• Rotating hitch and articulated steering provides good

off-road mobility and less stress on the frames in toughapplications. High positioned hitch provides high groundclearance and stability.

High strength steel 400 HB body• High chute and tipping joint with 70º or greater dump angle

promotes load retention and ejection.

High-Capacity Cooling System• Power and fuel saving, hydraulically driven, side mounted variable

speed fan consumes power only when needed.SpeedA25D Forward1 5.0 mph (8km/h) 2 7.5 mph (12km/h) 3 13.6 mph (22km/h) 4 19.3 mph (31km/h) 5 24.8 mph (40km/h) 6 32.9 mph (53km/h) Reverse1 5.0 mph (8km/h) 2 8.1 mph (13km/h)

Load capacityA25D Standard BodyLoad capacity 26.5 sh. tn. (24000kg) Body, struck 15.3 yd.3 (11.7m3) Body, heaped 19.6 yd.3 (15,0m3)With underhung tailgateBody, struck 15.7 yd.3 (12.0m3)Body, heaped 20 yd.3 (15.3m3) With overhung tailgateBody, struck 15.8 yd.3 (12.1m3)Body, heaped 20.4 yd.3 (15.6m3)With over- and underhung tailgateBody, struck 15.8 yd.3 (12.1m3)Body, heaped 20.4 yd.3 (15.6m3)

6

222-

21-1

0

170

COMPACTORS

Soil Compactors

High performance, seven-ton compactorThe SD Series vibratory soil compactors with 66 inch (1676mm) and 84 inch (2134mm) vibratory drums offer many innovative features thatprovide excellent drum performance, serviceability, reliability and a safe,comfortable and productive environment for the operator. The SD-77DX/SD-122DX smooth drums and SD-77F padfoot drum are engineered toefficiently and effectively compact all types of soils — granular, mixed or cohesive.

SD-77DXOperating Weight ...............16,350 lbs. (7415kg)Drum Width..................................66" (1676mm)Drum Diameter.............................48" (1219mm)

SD-77FOperating Weight ...............17,780 lbs. (8063kg)Drum Width..................................66" (1676mm)Drum Diameter.............................48" (1219mm)

SD-122DXOperating Weight ...........26459.9 lbs. (12002kg)Drum Width..................................84" (2134mm)Drum Diameter..........................58.7" (1490mm)

KEY FEATURES

• Audible and visual warning light for engine oil pressure,coolant temperature, hydraulic oil temperature and air cleaner restriction.

• Battery master switch. • Centrally located remote-mounted hydraulic oil filters and

hydraulic test ports with quick disconnect fittings.• Control console also includes cup holder, storage and

power outlet.• Easily accessible battery protected behind hinged steps.• Gauges for coolant temperature, fuel, hour meter

and tachometer.• Heavy-duty axle with No-Spin® differential.• Hydraulic and eccentric oil level sight gauges.• Inside drum scraper bar.• Lockable control panel, engine cover and fill caps.• Premium 6-way adjustable suspension seat, including swivel

feature and arm rest.• Premium shock mounts for operator platform.• Rear-mounted cooling system, easy access for cleaning.• ROPS/FOPS with seat belts.• Safety features include skid-resistant deck with foot rest,

dual deck rails, hand rails, seat switch, back-up alarm, hornand emergency stop.

• Single control for direction and speed with on/off vibration switch.

• Tilt steering column with console.• Warning lights for battery discharge and parking brake.• Work lights (two front and two rear) mounted on

ROPS/FOPS.

Spring-loaded sign stands / Roll-up Signs• Spring-loaded sign stands display

36" and 48" roll-up panels a minimum of 14" off the ground.

• Patented spring design incorporates anti-rotational device and positive stops to prevent spring over-stress.

• Exclusive base, spring and leg design eliminates the need for sandbags and absorbs winds up to 50 mph.

• Unique kicklock release lever allows easy leg unfolding and adjusting to uneven terrain.

• Quick lock mast allows for easy panel set-up / take-down. Velcro strap-on mast prevents panel from windmilling when wrapped around vertical fiberglass rib.

• Durable, lightweight and corrosion-resistant aluminumlegs provide longer service life and easier handling without sacrificing strength.

• Four steel L-shaped brackets reinforce legs to base. Telescoping aluminum legs provide maximum stability.

1101

-6-1

0

171

CRASH TRUCK

CCRRAASSHH TTRRUUCCKK

Hawkins Graves own portable roadhazard, directional alert systemtruck equiped with arrow boardsand attenuators.

6

3103

-1-1

0

172

GROUND ENGAGEMENT TOOLS

Hensley is proud to offer the Dura® line, a high quality, low cost alternative to our proprietaryproducts that delivers outstanding performance and value in a wide range of applications.Dura covers all popular Cat, H&L and Hensley Parabolic style adapters and teeth, andincludes a complete inventory of the latest design shapes. You can use this ever-expandingline with confidence, knowing that it carries the same warranty coverage as Hensley brand products.

Direct Replacement PartsThe Hensley line of ground engaging tools for construction and mining also includes a wide selection of DirectReplacement Parts for OEMs. These custom-engineered products can be used with Hensley loaders and excavator buckets, and most other bucket brands.

The line features replacements for:Amsco style teeth, pins and rubber plugs Ateco style ripper teeth and fasteners Bofors style teeth Bucyrus-Erie style teeth and fasteners Case/Drott style backhoe and 4-in-1 bucket teeth, adapters and pins Caterpillar® teeth, adapters, ripper shanks, edge segments, shank guards,

compactor feet, side cutters, end bits, heel plates and fasteners John Deere style teeth and pinsErie-Strayer style clamshell teeth ESCO® style teeth, adapters, sidecutters, wear edges and pins Fiat Allis style teeth, adapters and pins Ford style backhoe teeth, adapters and pins Galion style scarifier shanks, tips and pins H&L style teeth, adapters and pins Hendrix style dragline and excavator teeth, and fasteners Komatsu style ripper teeth, excavator teeth, adapters, shank guards and fasteners O&K style teeth and fasteners Page style teeth and fasteners Preco style teeth, ripper shanks and fasteners Wearpact style teeth and fasteners.

3104

-1-1

0

173

TRENCH SAFETY

TuffGuy™ Aluminum / Pinless / Modular

• WHAT’S SO TUFF? – Robust-modular aluminum sidewalls and your choice of full-length steel or aluminum panel connectors allow this shield to drivewith the strength of a steel box and patented “pinless design.”

• STEEL PANEL CONNECTORS – increase the boxes overall strength and durability, allowing it to go deeper. Designed to feel and work like a steeltrenchbox, these connectors hold thick double walled aluminum panels[strong and lightweight], with the bottom spreaders positioned in a primelocation to install pipe.

• ALUMINUM PANEL CONNECTORS – aluminum panel connectors allowspreaders to vertically adjust (within depth rating limits).

V-Panel™ Flexible / Modular / Aluminum

• ADJUSTABLE PANELS – V-Panels are vertically adjustable to work around pre-existing lines - just lift a panel and lock. The bottom of each panel features a steel knife edge. The top of each panel features a durable pounding pad so you can push each panel in tough dirt without damaging the box. For jobs needing higher pipe clearence raise walers and lock.

• PINLESS DESIGN – other then spreader pins, everything on the V-Panel secerly bolts together. To adjust a panel, unscrew 2 bolts (one for each waler)position and tighten.

• DROP ‘ONS – attach to spreaders. For wider applications add panels toincrease drop ’on width. For narrow applications, remove panels.

• TELESCOPING SPREADERS – for adjustable width -OR- hydraulic struts with external pump bucket to pump out box and shore up the ditch.

Hydraulic Jacks Simple / Hydraulic / Kits

• FEATURES and BENEFITS –+ Heavier-duty high-strength rails + Rotatable finger guards+ Simple pin-on extensions + Factory certified repairs+ Overnight shipping on stocked parts + Zinc coated pins for easy assembly

and more....• MINIMAL STORAGE SPACE – isn’t the only benefit when it comes to

hydraulic jacks. These ultra-lite units can be grouped together and transported(safely) in a pickup. What’s better is the simple “one-man-installation.”

• KITS – come with four hydraulic systems, release and removal hooks, and a triple-seal pump bucket. Rails and cylinders ship partially assembled at reduced rates.

ShoreLite Lite™ Aluminum / Pinless / Modular

• QUICK / EASY and LIGHT – Aluminum design is built strong, light enough to assemble, install and disassemble, on site - by hand.

• PATENTED PINLESS DESIGN – that gives quicker assembly and disassemblies times. Spreader pins are the only pins found on this shield.

• ADJUSTABLE SPREADERS – This shield has a perfect design to be placedinside a narrow ditch to perform repairs. By attaching spreader adjustersusers gain the ability to widen this unit an additional 2' - giving more flexibility in the ditch.

• LIFTING and STORAGE – Single 2.5" wide panels come 3' high and stack one-on-top of each other. Lifting lugs are attached to the inside panel for easyrigging. Out of the ditch, a disassembled SSL requires limited storage space.

Lightweight Aluminum Modular trench safety systems such as SAFEGUARD SERIES are PE Certified, store and transport easily. The SafeGuard trench safety systems are design for repair and maintenancework for plumbers, utility companies, general industry and governmentagencies with underground maintenance departments.

V-Panel™

TuffGuy™Aluminum

TuffGuy™Steel

HydraulicJacks

ShoreLite Lite™

6

TITAN UTILITY

3104

-2-1

0

174

TRENCH SAFETY

TITAN BASIC SERIES TRENCH BOXES“Standard No Frills” affordable trench safety equipment. Simple, affordable, lowers your occasional use cost.

Also available the Basic 5Primary Uses: Occasional Mainline workProduction Depth: 14' to 17'Side Wall: 5"

Basic 6Primary Uses: Occasional Mainline workProduction Depth: 15' to 17'Side Wall: 6"

Basic 8Primary Uses: Occasional Mainline workProduction Depth: 12' to 15'Side Wall: 8"

The Basic 3 All Steel Trench BoxThe Basic 3 model is a series of shields for small excavators as well as rubber tired backhoes. Built with high standards to provide reliability in the field. This box is built tough and priced right. Anexcellent range of sizes is provided for the B3 model. This is a great model for municipalities, plumbersand industrial maintenance crews. Great shield for spot repairs, taps, minor mainline work.

Basic 3 Features• Tamping Blocks• Lifting Lugs• Forged

Spreader Pins• Solid Welded

Accessories• 12" X 12" Cut Out• Stacking Rings• Tandum Connectors• Lite Sling• Drop Ons

TITAN BEDDING BOX

KEEP YOU LOADER WORKING

At the most convenient time...your loader fills the bedding box easy and fast in between its majorfunctions of back filling, clean up and material movement.

When your ready to lay pipe...the excavator scoops the beddingmaterial out of the bedding box easily. When needed lays a bed of gravel evenly in the trench eliminating delays and costly labor.

The by-product of better production...is safety on the job, by eliminatingdelays and the loaders putting excess pressure on the trench walls.

FUNCTIONAL DESIGN

Walk Bar & Drag BarEASY movement on the jobReinforcedNO BULGE side and long lifeEasy Fill DesignFunnel like design for quickeasy bucket fill

9 Cubic Yard B

edding Box

TITAN RAP-O-ROUND

Rap-O-Round• 3" Side Walls with

Production Depth 8' to 16'• 5" Side Walls with

Production Depth 12' to 30'

Features• 24" Knife Edge Taper• 1/2" x 3" Cutting Bar• 3" and 5" (X) Strong Pipe Sockets• 3/4" and 1" Thick Pounding Pads• 2" and 2-1/2" Solid Stacking Lug Bar

Common featuresP.E. CertifiedO.S.H.A. CompliantTabulated Data1/2" x 3" Cutting Bar

Kundel goes beyond...Formed Steel DesignContinuous Steel Members12” and 18” High Tapered Knife EdgeInternal Pounding MembersReinforced Knife EdgeInternal Stacking SystemEasy Slide Outside EdgeOne C Soil Depth RatingVertical Reinforced Pounding AreaReinforced Through Wall Sockets

Common featuresP.E. CertifiedO.S.H.A. CompliantTabulated Data1/2" x 3" Cutting Bar

Kundel goes beyond...Formed Steel DesignContinuous Steel Members24” High Tapered Knife EdgeInternal Pounding MembersReinforced Knife EdgeInternal Stacking SystemEasy Slide Outside EdgeOne C Soil Depth RatingVertical Reinforced Pounding AreaReinforced Through Wall Sockets

Titan Utility• 3-1/2" Side Walls with

Production Depth 8' to 16'or Production Depth 12' to 20'

• 5" Side Walls withProduction Depth 12' to 24'

• 6-3/4" Side Walls withProduction Depth 17' to 30'

Features• 12" and 18" Knife Edge Tapers• 1/2" x 3" Cutting Bar• 3" and 5" (X) Strong Pipe Sockets• 3/4" and 1-1/2" Thick Pounding Pads• 2", 2-1/2" and 3" Solid Stacking

Lug Bars

Date:

Company or Individual Name:

Address: City: State: Zip:

MailingAddress: City: State: Zip:

Telephone: Fax: Cell:

Contact Person: Years in Business:

The following information MUST be filled out in full. All information will be held in the strictest confidence.

We are a (please check one): Corporation: Fed ID #:

Partnership: SS #:

Sole Proprietorship: SS #:

Other: ID #:

OWNERSHIP:

Name & Title: Telephone:

Home Address:


Home Address:


Home Address:

Trade References: FAX NUMBER MUST ALSO BE COMPLETED

Company Name: Telephone: Fax:

Address:


Address:


Address:

P.O. Box 11675 (24506)13432 Wards Rd.Lynchburg, VA 24501

www.hawkinsgraves.com

(434) 847-7703toll free (866) 847-7703

fax (434) 847-7707

(Over)

CREDIT APPLICATION

Bank Information:Primary Bank Name: Contact:

Branch: Telephone: Fax:

Notice: Please read the following terms and conditions before signing this agreement:

If HAWKINS-GRAVES, INC. opens an account for us we agree to the following:

1: We will pay each invoice within 30 days of its date.2. We will pay a service charge of 1½% per month on any invoice 31 days or older.3. We will pay attorneys’ fees and costs in the event that collection efforts become

necessary on any delinquent invoices.4. This agreement shall remain in effect as long as the undersigned shall remain

indebted to HAWKINS-GRAVES, INC.

We certify that the above information is true and correct, and that we can comply with the termsspecified in this document.

Signature & Title Date

Signature & Title Date

Hawkins-Graves Office Use Only:

References Checked By: Date:

Credit Approved By: Date:

Credit Refused By: Date:

Customer Contacted By: Date:

P.O. Box 11675 (24506)13432 Wards Rd.Lynchburg, VA 24501 www.hawkinsgraves.com

(434) 847-7703toll free (866) 847-7703

fax (434) 847-7707

hawkinsgraves.com 622-16-10 10 RIDE-ON TROWELS HD & HDX SERIES HYDRA-DRIVE SERIES All-Hydraulic...

Documents

Transcript of hawkinsgraves.com 622-16-10 10 RIDE-ON TROWELS HD & HDX SERIES HYDRA-DRIVE SERIES All-Hydraulic...