Castrol Marine has welcomed new guidance from Wärtsilä that undermines claims that mid-range base number (BN) oils represent a single cylinder oil solution for marine 2-stroke engines. The advice confirms Castrol’s long-held concerns that using mid-range BN cylinder oils with higher sulphur fuels when slow steaming could lead to cold corrosion.

The engine major has withdrawn approval for mid-range (50-60BN) cylinder oils when used with many marine engines running on Heavy Fuel Oil of above 2.5% sulphur content.

New ‘letters of no objection’ to suppliers limit use of mid-range BN oils on all “Wärtsilä RTA, RT-flex and W-X engines as well as Sulzer 2-stroke engines” to HFO whose sulphur content is “in the range 0.5<S<2.5 mass %”.

“Our concerns on catch-all, mid-range BNs for slow steaming were first prompted by our own field investigations and then confirmed by bench tests and further field trials,” says Paul Harrold, technology manager, Castrol Marine. “We have consistently argued that mid-range BN oils are not suitable for slow steaming operations on modern engines. The two leading OEMs in the market have now offered specific advice on this issue in line with our position.”

The Wärtsilä letters have been followed by key ‘single oil solution’ proponents acknowledging to customers that cylinder oils previously recommended for HFO with up to 4.5% sulphur content are now for restricted use only.

Castrol Marine was the first cylinder oil supplier to raise concerns on cold corrosion after a number of suppliers presented mid-range BN oils as suitable for slow steaming operations. It has consistently advised customers to use an accurate approach when making lubricant choices, based on engine type and operating conditions rather than simplicity and convenience alone.

In May 2013, Castrol reported case studies for in-service ships to the CIMAC Congress in Shanghai showing evidence of the harmful impacts of cylinder oils of inadequate BN in slow steaming regimes. Data supported the view that higher BN lubricants reduce corrosive wear in slow steaming engines and enable lower, more cost effective feed rates than mid-range BN oils.

Wärtsilä advice cONFirMs castrOl cONcerNs ON siNgle Oils

0º

30º

60º

90º

120º

150º

180º

95000699_CASTROL_PRESSRELEASE.indd 1 20/06/2013 10:35

Castrol Marine recommends Castrol Cyltech 80 AW in combination with its scavenge drain analysis service to achieve safe slow steaming operations that do not compromise engines or increase lube oil feed rates. The company has also recently responded to customer demand by increasing availability of its 80BN Cyltech 80 AW cylinder oil to 35 ports. Cyltech 80 AW is formulated for crosshead engine types operating on high sulphur residual fuel, typically above 2.5% content.

“MAN Diesel & Turbo has already excluded mid-range cylinder oils from its approved list for newer engines,” says David Goosey, Castrol Marine chief executive and sales director. “Some argued that MAN’s advice was only relevant for a small number of engines. Wärtsilä’s restriction effectively excludes the use of mid-range BN oils for about two thirds of the fuel used in the relevant engines outside ECAs.”

Notes to Editors:

Issued on behalf of the Castrol Marine Press Office by Hugh O’Mahony. For enquiries from the media, journalists and researchers only, please contact:

Hugh O’Mahony, PR Director, JLA Media Ltd, Windmill Suite, Wimbledon Village Business Centre, Thornton House, Thornton Road, Wimbledon, London SW19 4NG, UK

Telephone: +44 7949 708 679 E-mail: hugh.omahony@j-l-a.com

For more information relating to Castrol Marine’s products and services, visit www.castrol.com/marine

0º

30º

60º

90º

120º

150º

180º

95000699_CASTROL_PRESSRELEASE.indd 2 20/06/2013 10:35