5.00 Section 5 cover 151117
Transcript of 5.00 Section 5 cover 151117
Options Available• Flanged connections • Magnetic starter and circuit breaker• Explosion Proof to Class 1, Div.2, Group D • Lower noise fan assembly option• NEMA 4X stainless steel control enclosure • Horizontal unit mount configuration • Automatic-on starts fan automatically on liquid introduction• Electric or gas-fired defrost• Designs for power other than standard 480/400/240V• Stainless steel or Monel liner available for Electronics Industry and service to 6000 psi (414g)
HAF-816-FHAF-825-FKAF-825-FHAF-836-FKAF-836-FHAF-864-FKAF-864-FHAF-899-FKAF-899-FBAF-899-F
UAF-880-FL35UAF-1280-FL35
20,00030,00036,00045,00054,00080,00095,000125,000140,000175,000280,000400,000
5257909451185142021052500329036854600740010500
2.22.22.23.73.77.57.57.57.57.51616
ModelOxygen Rating PowerSCFH Nm³ / hr kW
Performance Data
Dimensions
HAF-816-FHAF-825-FHAF-836-FHAF-864-FHAF-899-FBAF-899-f
UAF-880-FL35UAF-1280-FL35
inches193193193205226286505505
mm4900490049005200575072651282712827
inches3745526985859292
mm9001150130017502150215023302330
inches506067841001009797
Lbs2200250031004300550080001600020000
kg10001135140519502495360064009000
mm12501500170021502550255024642464
ModelHeight Width Depth Weight
Fan Assisted Series HAF and KAF
DISTRIBUTED BY:5.01
CRYOGENIC PRODUCTS
Cryoquip fan-assisted units provide maximum heat exchange and high vaporization rates of liquid oxygen, nitrogen, argon, LNG and other cryogenic fluids. The heat exchange elements are 8 inches (200 mm) aluminum construction from tip to tip, with internal fins providing additional surface for a maximum performance. The KAF and BAF series elements are taller than the HAF and can therefore provide more capacity. The UAF model is Cryoquip’s high efficiency Uniflo fan ambient vaporizer. The UAF is the most efficient high capacity vaporizer in the industry. The 100% counter flow design provides for the greatest heat transfer efficiency and structurally the most reliable design. In many instances, fan units may provide an economic advantage over natural draft vaporizers, especially at higher capacity where electric power is available and high capacity are required in small plot spaces. Multiple units can be used to suit a wide range of performance requirements.• These vaporizers offer ample exchange surface to permit substantial short-term accumulation
of ice not blown off by the forced air flow. Brief periods of no load operation at temperatures above freezing also allow the unit to begin shedding accumulated ice. All models consist of Cryoquip’s Alpine 800 extended height heat transfer elements with a direct drive fan assembly at the top to force air downward through the heat exchange array. The standard fan assembly includes a hot dip galvanized venture motor mount assembly, and fan intake safety screens.
• These units include integral magnetic motor starters with circuit breakers and NEMA 4 electri-cal cabinet with door interlock. Other options include flanged connections, an “automatic-on” feature which permits the fan to start automatically when liquid is introduced, stainless steel or monel liner for service to 6000 psi (414 bar), multiple unit switching controls for continuous operation, and Cryoquip’s HEXAD electrical or gas-fired defrost system for colder climates.
Lower noise fan options are also available.
• Ratings are for 8 hours at 70ºF (21ºC) and 70% relative humidity and are based on saturated liquid oxygen inlet with a 30ºF (17ºC) approach to ambient temperature.
• Standard units have maximum allowable working pressure up to 500 psig (34.5 barg). Pressure drop is typically 15 psi (1 bar) depending on model size, when operated at 175 psig (12 barg) discharge. Standard electrical power is 480/400/240 Volts 3 phase 50/60 hertz.
HAI812SXX**HAI816SXXHAI820SXXHAI824SXXHAI830SXXHAI836SXXHAI848SXX
41 x 3241 x 4141 x 5041 x 6050 x 6060 x 6078 x 60
500065008300
10,00012,50015,00020,000
450 sq. ft.600 sq. ft.750 sq. ft.900 sq. ft.1125 sq. ft.1350 sq. ft.1800 sq. ft.
385 lbs.500 lbs.630 lbs.815 lbs.940 lbs.1100 lbs.1450 lbs.
Model*LxW
Inches8 Hour
Rating SCFHExternal HeatTransfer Area
ApproximateModule Weight
* For other models to meet special requirements, consult factory.** SXX refers to model designations S30, S45, S60 with maximum pressure ratings of 3000 psig, 4500 psig, and 6000 psig, respectively.
DISTRIBUTED BY:5.02
CRYOGENIC PRODUCTS
HAI 800-SXX SeriesThe new HAI 800 high pressure series cryogenic fluid vaporizers have all the benefits of the original HA Series high pressure units for intermittent operation and for 8 hours of continuous service PLUS the following enhanced structural characteristics:• New, improved unitized construction yields the highest structural strength to cost ratio
available, and precludes the use of welds that cannot be heat treated, thereby maintaining the greatest structural integrity.
• Employs unique Cryoquip patented “spar” link design; a unique, efficient attachment method enhancing load carrying capability.
• Can be handled with a fork lift without the vaporizer sustaining damage.
Additionally the following features are still preserved:• Extra capacity. Each finned aluminum heat transfer element features eight fins which
measures 8 inches from tip to tip and provides high capacity performance and fast defrosting. Elements have approximately five square feet of external heat exchanger surface per foot of length.
Enhanced heat transfer. The pressure retaining liner for pressures up to 7500 psig is hydrostatically expanded into each finned element to provide a 100% metal to metal bond between the aluminum element and the stainless steel liner. This produces the highest possible effective heat transfer rate and eliminates inefficiency and potential sealing problems associated with the use of heat transfer fluids between the liner and the finned element, as well as inefficiency resulting from the air gaps characteristics of “clamp-on” or glued elements.
Module Overall Height 114 InchesCenterline Spacing 9.25 InchesGround Clearance 20 InchesWorking Pressure 3000 PSIG, 4500 PSIG 6000 PSIG Other Models in this Series available to 15,000 PSIG
End Connections Liner Material
Piping
Ratings
Other fluids
Ratings listed are for saturated oxygen at 2200 PSIG on 230ºF on 70ºF day with 70% relative humidity and a gas discharge temperature of 40ºF. Actual conditions may require a reduction in flow. The down rating is a matter of experience with the geographical location of unit and the duty associated with the application.
- Inlet and outlet ½” FPT. Other connections available on special order. - Type 304 Stainless Steel. Other metals such as 316 series or Monel are
available on special order.- Units are internally piped in a series configuration. Special piping with any
number of parallel passes are available on special order- The performance of ambient air vaporizers is subject to many fact. These
include flow, duty, cycle, outside temperature, relative humidity, altitude, wind, solar radiation, defrosting intervals, operation pressure and adjacent structures.
- For ratings on other fluids such as Hydrogen, LNG, Nitrogen, Carbon Dioxide Argon, Methane, Ethane, Propane, Carbon Monoxide, Propylene, Ethylene or other low-temperature gases, consult our Application
CRYOGENIC PRODUCTS
ModelOverall Length
SEB 1RSEB 2RSEB 3RSEB 4RSEB 6RSEB 8RSEB 10RSEB 12R
Inch2424324048648096
mm61061081010201220162520302440
DISTRIBUTED BY:5.03
SEB Series Trim HeaterCryoquip manufactures a new series of modular Trim Heaters. The new units are available for use with industrial gases such as Oxygen, Nitrogen, Argon, CO2 as well as other specialized gases.
Improved features include:• Removable and replaceable heater elements• Low pressure drop• Small footprint• Lightweight and portable
Electric Cryogen Trim Heater utilize high quality electric heating elements and stainless steel heat exchanger tubes. Heating elements and tubes are specially positioned in the highly conductive aluminum modules. Modules consist of multiple stainless steel tubes in parallel to provide low pressure drops. The electric trim heaters are made optionally for high purity applications which include electropolished tubing.
System Features• Solid state temperature controller.• Independent solid state auto resetting high-temperature switch controller.• A separate manual/auto resetting high limit shutdown controller. NEMA 4 electrical control
enclosure, door interlock handle.• Individual electrical components UL recognized. CSA certified, IEC approved and CE stamped.
Standard Options Available• Low temperature solenoid shut-off valve • NEMA 4x electrical control enclosure.• ANSI, Mueller four-bolt or DIN Flange end connections.
Design Data• Standard maximum working pressure 450 psig (30 barg) : working pressures to 10,000 psig
(690 barg) available.• Pressure drops are based on 100 psig (6.9 barg) inlet
Units available in multiple voltages (575V, 480V, 415V, 400V, 380V, 240V). Power requirements may vary slightly with each specific model. Consult factory for pricing and delivery.
Pressure Drop
Flow rate
SCFH/Nm³/hr5,000/13010,000/260
15,000,395
20,000/525
25,000/657
30,000/790
40,000/1050
Temp-rise
ºF / Cº125/70125/7063/35125/7084/4742/23125/7094/5263/35100/5575/4250/28125/70104/5884/4763/35125/7094/5263/35
2/0.1
SEB-2R-8T6-10-X
SEB 3R-12T6-15-X
SEB 5R-20T6-25-X
5/0.4SEB 1R-4T6-5-X
SEB 1 R-4T6-5-X
SEB 3R-12T6-15-X
SEB 2R-8T6-20-X
SEB 2R-8T6-10-X
SEB 3R-12T6-30-X
SEB 3R-12T6-30-X
SEB 4R-16T6-20-X
SEB 4R-16T6-40-X
SEB 4R-16T6-20-X
10/0.7
SEB 1R-4T6-10-XSEB 1 R-4T6-5-X
SEB 2R-8T6-20-XSEB 2R-8T6-10-X
SEB 2R-8T6-20-X
SEB 3R-12T6-30-X
SCFH/Nm³/hr80,000/2100
100,000/2630
60,000/1580
70,000/1840
50,000/1315
ºF / Cº125/7094/5263/357/26
125/70100/5563/3550/28125/70105/5863/3552/29140/78108/6072/4054/30125/70100/5563/3550/28
5/0/4SEB 8R 32T6 80 X
SEB 8R 32T6 40 X
SEB 10R 40T6 100 X
SEB 10R 40T6 50 XSEB 6R-24T6-60-X
SEB 6R-24T6-60-XSEB 8R-32T6-80-X
SEB 8R-32T6-40-X
SEB 5R-20T6-50-X
SEB 5R 20T6-25-X
10/0.7
SEB 6R 24T6 60X
SEB 6R 24T6 30 X
SEB 8R 32T6 80X
SEB-5R-20T6-50-X
SEB 5R-20T6-25-X
SEB 6R-24T6-60-X
SEB 6R-24T6-30-X
SEB-4R-16T6-40-X
SEB-4R-16T6-20-X
Psi/bar Psi/bar Psi/bar Flow rateTemp-rise
Psi/bar Psi/bar
*US Patent #5,251,452
DISTRIBUTED BY:5.04
CRYOGENIC PRODUCTS
UFV Uniflo® SeriesCryoquip’s UFV Uniflo® Series ambient air vaporizer is an entirely new, patented* concept in high-flow natural draft vaporizers, designed for ambient air vaporization of cryogenic fluids. The Uniflo® vaporizer had significant advantages over conventional designs for high flow service. The heat transfer elements are connected in parallel, which eliminates the differential thermal gradients between extrusions.Counter flow heat exchange between the downward flow of air in natural convection and the upward flow of the cryogenic in the vaporizer improves the thermal performance substantially compared to conventional designs with the same surface area.Ice accumulates safely during continuous operation in the lower part of the vaporizer with ice free extrusions protruding out of the ice pack. The low ice build-up lowers the center of gravity and therefore, reduces structural requirements in meeting the Uniform Building Code (UBC).
DescriptionThe UFV series feature Cryoquip’s patented Uniflo® configuration of all parallel flow offering the following advantages:• Even thermal gradients.• High-flow, low pressure drop design.• Unique internal aid fluid distribution• Ice forms safely at bottom of vaporizer.• Better approach exit temperatures from pure counter flow design.
Features• High thermal efficiency• Advanced integral design• Manufactured in the USA• Cleaned for oxygen service• Patented Spar Link© construction• Proven Cryoquip heat transfer design• Designed in accordance with the UBC and ASCE• Seismic zone 4,100+mph wind available• MAWP up to 580 psig (40 bar-g) standard• Flow rates up to 304,000 SCFH (8,000 Nm³/hr)
Model
UFV-856-XXL40UFV-864-XXL40
UFV-1264-XXL40UFV-1272-XXL40UFV-1280-XXL40UFV-1290-XXL40
Inch90989887101101
mm228624892489221025652565
Inch799090827887
mm200722862286208319812210
Inch525525525525525525
mm133351333513335133351333513335
Dimension A (Length) Dimension B (Width) Dimension C (Height)
UFV 856(XX)L40
UFV 864(XX) L40
UFV 1264(XX)L40
UFV 1272(XX)L40
UFV 1280(XX)L40
UFV 1290(XX)L40
11200
12800
19000
21300
23700
26700
1040
1250
1775
2000
2220
2500
116600
133200
190200
213100
235900
266300
3065
3500
5000
5600
6200
7000
108300
123700
140800
156000
175000
197900
2845
3250
3700
4100
4600
5200
99900
114200
127500
140800
156000
178800
2625
3000
3350
3700
4100
4700
85100
97100
108500
121800
133200
152200
2235
2550
2850
3200
3500
4000
76700
87500
97100
106600
121800
137000
2015
2300
2550
2800
3200
3600
70000
79900
87500
95200
106600
121800
1840
2100
2300
2500
2800
3200
Capacities
Modelft² m² SCFH Nm³/hr SCFH Nm³/hr SCFH Nm³/hr SCFH Nm³/hr SCFH Nm³/hr SCFH Nm³/hr
Surface Area 8 hr Capacity 12 hr Capacity 16 hr Capacity 24 hr Capacity 48 hr Capacity 72 hr Capacity
5.05
CRYOGENIC PRODUCTS
Wide Space Ambient Air Vaporizers SeriesNew, improved unitized construction yields the highest structural to cost ratio available, and precludes the use of welds that cannot be heat treated, thereby maintaining the greatest structural integrity.• Employs the unique Cryoquip “spar” link design; an efficient attachment method that
enhances load carrying capability, which maintains the highest level of structural integrity available in the industry, during all modes of transportations.
• Can be deployed or redeployed with ease since these units are capable of resting on a flat bed trailer without the need for added shipping pallets, support blocks, or other shipping pieces.
• Can be handled with a fork lift without the vaporizer sustaining damage.• Can be tied down on a trailer without any additional crating provisions.• Lifting eyes are provided to facilitate handling.• Designed in accordance with the Uniform Building Code (UBC) and applicable sections of
ANSI A 58.1. Units available for seismic zone 4, and 100 mph (160 km/h) conditions with normal frost loading.
• Continuous service rating is permitted for operating periods 5 to 7 days, or longer under certain conditions, with greater frost/ice loading for freeze periods.
YEW C
HEONG (A
SIAPA
C) PTE L
TD
YEW C
HEONG (A
SIAPA
C) PTE L
TD
YEW C
HEONG (A
SIAPA
C) PTE L
TD
YEW C
HEONG (A
SIAPA
C) PTE L
TD
YEW C
HEONG (A
SIAPA
C) PTE L
TD
YEW C
HEONG (A
SIAPA
C) PTE L
TD
YEW C
HEONG (A
SIAPA
C) PTE L
TD
YEW C
HEONG (A
SIAPA
C) PTE L
TD
YEW C
HEONG (A
SIAPA
C) PTE L
TD
YEW C
HEONG (A
SIAPA
C) PTE L
TD
YEW C
HEONG (A
SIAPA
C) PTE L
TD
YEW C
HEONG (A
SIAPA
C) PTE L
TD
YEW C
HEONG (A
SIAPA
C) PTE L
TD
VAI 804 FVAI 806 FL 10VAI 806 FL 12VAI 812 FVAI 812 FL 12VAI 812 FL 15VAI 816 FL 10VAI 820 FL 12VAI 824 FL 12VAI 830 FL 12VAI 836 FL 12VAI 836 FL 15VAI 836 FL 18VAI 836 FL 20VAI 848 FL 12VAI 848 FL 15VAI 848 FL 18VAI 848 FL 20VAI 856 FL 12VAI 856 FL 15VAI 856 FL 18VAI 864 FL 15VAI 864 FL 18VAI 864 FL 20VAI 872 FL 20VAI 872 FL 23
1503003604507209008001200144018802160270032403600280036004320480033604200504048005760640072008280
14283342678474112134167201251301334268334401446312390468446535595669769
884004404706507807001200135017502100250028003100250032003600400030003750480048005500620070007900
4025096817514301716410264061079595011351270140511351450163018151360170021752175249528101540017380
21x2131x2131x2143x3243x3243x3246x4658x4669x4658x6969x6969x6969x6969x6991x6991x6991x6991x6978x9178x9178x9191x9191x9191x91102x91102x91
650x650850x650787x533850x11501092x8131092x8131150x11501473x11681750x11501450x17501750x17501750x17501750x17501750x17502300x17502300x17502300x17502300x17502000x23002000x23002000x23002300x23002300x23002300x23002591x23112591x2311
1.53.04.04.27.810.08.012.014.519.523.029.536.040.531.039.548.054.037.047.557.054.066.073.585.0100.0
367910510820526321031538051560577594510658151040126514209751250150014201735193522342629
1.02.02.93.25.77.26.09.011.014.017.021.526.529.522.529.035.539.527.035.042.039.548.053.560.067.0
285376821491891582372903704455656957755907659351040710920110510401265140515771761
0.81.52.12.54.35.44.56.88.510.513.016.520.022.017.021.526.529.520.026.031.029.536.040.045.050.0
21395563113142118179225275340435525580445565695775535683820775945105011831314
0.71.31.72.13.4.43.55.67.08.510.513.516.018.014.018.021.524.017.022.026.024.029.032.537.041.0
1834455392116921471852252753554204753704755656304455706856307658559731078
ft² m² lbs kg inches mm 8-hours 1-day 3-days 5-7 day
ModelExternal HeatTransfer Area
Approx Weight
L x WRatings
KSCFH (Nm³/hr)
Dimensions Performance Data
DISTRIBUTED BY:5.06
CRYOGENIC PRODUCTS
• Increase ground clearance further enhances heat transfer by natural convection.• Extra capacity. Each finned aluminum heat transfer element features eight fins which measure 8 inches (200 mm) from tip to tip and
provide high capacity performance and fast defrosting. Elements have approximately 5 square feet per foot length (1.5 square meters per meter length) of external heat-exchanger surface area.
• Low pressure drop, full-bore passages in the elements provides more flow cross section. Internal fins promote heat transfer with additional surface area.
• Heat transfer elements of heights to 23ft (7,010 mm) are available to meet a range of process demands. Common assembly configurations and ratings are shown on the reverse side.
• New, larger bore fluid pages are available to maintain ultra low pressure drops on high flow rate multiple element units.
For models to meet special requirements including other models for greatly extended operating periods; for low pressure drop requirements for these vaporizers and others; for pressure drops for 8 hour ratings- consult Cryoquip. Pressure drop is less than 10% for the 1 day rating, based on 150 psig (10.3 bar) inlet pressure for all models except the L-18 and L-20 series. The performance of ambient air vaporizers is subject to many factors. These include flow, duty cycle, ambient temperature, relative humidity, freeze period, altitude, wind, solar radiation, operating pressure and proximity to adjacent structures. The effects of average solar and wind conditions are not included in the above ratings. Ratings are based on mean ambient conditions of 70ºF (21ºC) and 70% relative humidity. Special conditions may vary considerably for a particular application, thereby affecting performance.
SpecificationModule overall Heights; End Connections L-10:163” (4150mm), L-12:185” (4700mm), L-15:220”(5600mm) Standard: four bolt flange L-18:255” (6450mm), L-20:291”(7400mm),L-23:327”(8300mm) Optional: four bolt mates Working Pressure- Up to 500 psig (34.5bar) 1,1½, and 2 inch (All Aluminum Units)
Options AvailableSpecial end connections available on special order.Stainless Steel or Monel lined for services up to 15,000psig (1,034bar) and for semiconductor industry applications. Complete piping module assembly packages for complete vaporizer/piping installation.
VEC/VEB Series Electric Vaporizer
Cryoquip manufactures a new series of NEMA 4 modular Electric vaporizers. The new units are available for use with industrial gases such as Oxygen, Nitrogen, Argon (model VEB), and Carbon Dioxide (model VEC) as well as other special fluids.
Improved features include: • Removable and replaceable heater elements • Low pressure drop • Smaller footprint • Lightweight and portable
• Electric Cryogenic Vaporizer utilize high quality electric heating elements and stainless steel process tubes. Heating elements and tubes are specially positioned within the highly conductive aluminum wafer modules. Heat transfer is further enhance in vaporizer units by means of a spirovane turbulence promoter within each stainless tube, which also reduces fluid slugging and surging.
• Special Designs are available for low temperature gas exit vaporizers with controls to provide exit gas temperature near saturated vapor for special applications.
The new VEC/VEB Electric vaporizer SeriesVEC-Carbon Dioxide ServiceVEB-Oxygen, Nitrogen, Argon Service
VEx 1R 2T12VEx 2R 3T12VEx 2R 3T24VEx 3R 4T24VEx 4R 6T12VEx 6R 8T12VEx 10R 12T12
Model
28.5 (724)28.5 (724)28.5 (724)28.5 (724)28.5 (724)28.5 (724)34.5 (877)
24 (610)24 (610)24 (610)24 (610)30 (762)30 (762)30 (762)
A B
*Dimensions - Inch (mm)
Standard/ Options Available• Electronic digital controller• Wafer module insulation• Stainless steel enclosures• ANSI, Mueller four-bolt or DIN flange end connections• Explosion-proof Class 1, Div.2, Group D• Alarm dry contacts• ASME Code Certification
Design Data• Standard maximum working pressure 450 psig (31 barg); working pressures to 10,000 psig, (690 barg) available.• 10psi (.7 bar) pressure drop at rated flow and 150 psig (10 barg) working pressure, except T24 O2 units have higher pressure drops.
System Features• Easy dial thermostatic temperature controller.• Adjustable auto resetting over-temperature switch.• Adjustable manual resetting high limit shutdown switch.• NEMA 4 electrical control enclosure, door interlock handle.• Non-overheating design during no-flow.• Individual electrical components U.L. recognized, CSA certified and IEC approved.• Replaceable heating elements.
Units available for any voltage. Power requirements may vary slightly with each specific voltage.
• For pressure greater than 580 psig (40 barg) consult factory for proper model number. Specify operating pressure range.
DISTRIBUTED BY:5.07
CRYOGENIC PRODUCTS
Model Power N2/O2 Flow Capacity
(kW) SCFH Nm³/hr(240V/480V)*
Model Power CO2 Flow Capacity
VEB 1RVEB 1RVEB 1RVEB 2RVEB 4R VEB 4RVEB 4RVEB 6RVEB 6RVEB 10RVEB 10R
2T122T122T123T126T126T126T128T128T1212T1212T12
5(X)10(X)15(X)30(X)40(X)50(X)60(X)70(X)90(X)120(X)135(X)
51015304050607090
120135
306092184239300368421552736810
VEC 1RVEC 1RVEC 1RVEC 2RVEC 2RVEC 2RVEC 2RVEC 3RVEC 3R
2T122T122T123T123T243T243T244T244T24
5 (X)10 (X)15 (X)30 (X)40 (X)50 (X)60 (X)75 (X)90 (X)
51015304050607590
114228342684912
1,1401,3681,7102,052
52104155311415518622777933
1,1602,2803,5007,0009,100
11,40014,00016,00021,00028,00030,800
kg/hrlb/hr(240V/480V)*
*Note: (X) stands for either 240 or 480
(kW)
DISTRIBUTED BY:5.08
CRYOGENIC PRODUCTS
Vacuum Insulated PipeworkCryoquip is a world leader in Vacuum Insulated pipe work. Many users around the world refer these lines as SIVL (Super Insulated Vacuum Line) or VIP (Vacuum Insulated Pipe) or similar terms. Cryoquip can supply lines in all sizes up to 12" inner and in both tube and pipe sizes. Cryoquip builds these lines in easily transportable and installable individual spools. Each spool has its own vacuum jacket, with its own vacuum / relief port. The vacuum line spools may be connected either by our special low heat in-leak bayonet connec-tion or with sleeved butt weld connections. Our lines incorporate unique piping and bellows systems to ensure that internal pipe stresses are minimized and there is minimal heat inleak from external ambient heat sources.The outer jackets of the line are available in polished tube or mill finished scheduled pipe. The spools may be insulated in either multi layer insulation or aluminized mylar insulation. Each spool containers special "getter" material, which adsorb any gas molecules that may “out-gas” inside the annual space of the vacuum line.Every line is vacuumed individually to less than 1 x 10 - 4 Torr, and Helium mass spectrometry tested. The lines are then cold shocked and pressure tested to ensure they have the highest vacuum integrity.Cryoquip is the world leader in vacuum lines, and can provide cost competitive price for any vacuum insulated system.
Trailer Pumps
Pump
Type
Applications
Liquid Pumped
Flow Rate
Differential Head
Top
Jackshaft or Hydraulic
Trailer off load/Boost
N2, O2, Ar
25-290 gpm/ 95-1,100 lpm
100-2,3200 ft/ 31-670 m
TC 21 HD
Jackshaft or Hydraulic
Trailer off load
N2, O2, Ar
25-225 gpm/ 95-852 lpm
100-1,200 ft/ 31-666 m
CP 160/180
Gearbox/Close-coupled
Trailer/Transfer
N2, O2, Ar, CO2, N2O
25-180 gpm/ 95-684 lpm
49-1,476 ft/ 14-450 m
Submerged/Sealess Pump
Pump
Applications
Liquid Pumped
Flow Rate
Differential Head
AC/TC-34
Transfer, LNG Filling
N2, Methane (LNG), Ar
15-115 gpm/ 56-435 lpm
50-1,600 ft/ 15-488 m
AC-32
LNG refueling/Loading
Methane (LNG)
4-500 gpm/ 15-1893 lpm
21-1,625 ft/ 6.4-207 m
Cylinder Filling Pumps
Pump
Duty
Liquid Pumped
Flow Rate
Discharge
Pressure
NDPD
Light/Medium
N2, O2, Ar
up to 2.7 gpm/
10.4 lpm
up to 4,000 psi/
267 bar
WDPD
Intermittent
N2, O2, Ar
1.6, 1.9, 2.2 gpm/
6.0, 7.2, 8.4 lpm
3,000 psi/
207 bar
P2K
Medium/Heavy
N2, O2, Ar, Methane
(LNG), Ethylene
up to 6.6 gpm/
25 lpm
up to 6,090 psi/
420 bar
RPSA 40
Intermittent
CO2, N2O, Halon
3.5 & 6.34 gpm/
14.5 & 24 lpm
1,740 psi/
120 bar
P 1100
Intermittent
CO2, N2O
5.8 gpm/
21.9 lpm
1,200 psi/
82.7 bar
DISTRIBUTED BY:5.09
CRYOGENIC PRODUCTS
Oil Well Service
Pump
Applications
Liquid Pumped
Flow Rate
Discharge
Pressure
Rod Load
Stroke
Cold Ends
3-GUPD/SG
Oil well service/Heavy Duty
N2, O2, Ar
up to 48 gpm / 183 lpm
to 17,000 psi/
1,172 bar
20,800 Lbs (9,435 Kg)
1.3” (33mm)
1.25, 1.625, 2.0
Storage Filling Pump
Pump
Lubrication Type
Liquid Pumped
Flow Rate
Discharged
Pressure
Modular Design
X9
Splash-Oil
N2, O2, Ar, H2, Methane (LNG)
0.94-37.1 gpm/ 3.57-140.1 lpm
up to 10,000 psi/
690 bar
Yes - 1, 2, or 3 cylinder
SGV
Forced-oil, Integral pump
N2, O2, Ar, H2, Methane (LNG)
0.94-26 gpm/ 3.6-98.8 lpm
up to 10,000 psi/
690 bar
Yes - 1, 2, or 3 cylinder
Mechanical and Labyrinth Pumps
Pump
Type
Applications
Liquid Pumped
Flow Rate
Differential Head
3-SLS
Oil well service/Heavy Duty
N2, Methane (LNG)
up to 200 gpm / 760 lpm
to 18,000 psi/
1,241 bar
58,000 Lbs (26,308 Kg)
2.25” (57.15mm)
2.0, 2.5, 2.7, 2.875, 3.25
3 HD 4
Oil well service/Heavy Duty
N2, Methane (LNG)
up to 220 gpm / 835 lpm
to 18,000 psi/
1,241 bar
65,000 Lbs (29,484 Kg)
4.0” (101.6mm)
2.0, 2.875, 3.25
AC-14
Gearbox
Trailer /
Transfer
N2, O2, Ar
10-250 gpm/
35-950 lpm
100-1,050ft/
30-320m
AC-48
Gearbox
Pipeline backup
High Pressure
Transfer
N2, O2, Ar
30-390 gpm/
114-1,475 lpm
400-2,000ft/
120-610 m
AC-18
Hydraulic
Boost
N2,
5-250 gpm/
20-950 lpm
40-600ft/
12-183m
AC/TC-21
Beltbox
Transfer /
Liquid fill
N2, O2, Ar
10-180 gpm/
35-680 lpm
100-1,100ft/
30-335m
TC-30
Close-coupled
Transfer /
Process (Laby)
N2, O2, Ar
16-630 gpm/
60-2,350 lpm
20-700ft/
6-210m
AC-48
Beltbox
Transfer,
Pipeline backup
N2, O2, Ar
20-200 gpm/
75-750 lpm
200-1,500ft/
60-455 m
DISTRIBUTED BY:5.10
CRYOGENIC PRODUCTS
Super Insulated Vacuum LineCryoquip has been a highly specialized manufacturer and installer of “static” Super Insulated Vacuum Line for handling low temperature fluids since 1986. The vacuum insulated piping comprises of an inner tube & outer jacket for transfer of mainly cryogenic fluids. The inner tube holds, the outer tube maintain the vacuum insulation and bears the external loads.The SIVL is divided into sections that are fully fabricated and tested in the factory prior to shipment. The vacuum lines are available in both Bayonet Or Butt-Weld connections. The sectionscan be rigid, flexible or a combination of both. Cryoquip piping utilizes vacuum insulation to virtually eliminate heat loss by conduction, convention and laminar radiation shielding to greatlyminimize radiated heat influx.
Features and Benefits: • Specifically designed to minimize any potential leak • Provide a quick & efficient installation at site, with no requirement for hot work • Incorporates multilayer insulation in an ultra high vacuum with a “getter” absorbing materials to prevent any out-gassing • Liquid savings • Extremely long life & minimum maintenance • Incorporates a permanent vacuum and does not require any vacuum pumps to maintain the vacuum integrity
Technical CharacteristicsDesign Pressure : 10 bar - 30 barDesign Temperature : -196 C / +65CInner Material : 316/304 SS Seamless Tube to ASTM A269/A213Outer Jacket : 304 or 316 Stainless Steel As Welded Polish TubeConnection Type : Bayonet Connection or Welded ConnectionCode : ASTM B31.3 Piping CodeVacuum Level Maintained : < 10 micronsFiller Insulation Material : MYLAR or Multi-Layer
Male Seal Ring
Inner
Teflon Nose Seal
Ring Flange
350
Expansion Bellows
Locating Bush
Outer185
MYLAR, MolecularSieve & Insulation
Pump Out Plug
Pump Out Port
Female Seal Ring
Ring Flange
Dimension
Inner TubeOuter Jacket
Unit
mmmm
Line Nominal Dimension3/4”
OD19.05 x 1.65OD76.2 x 1.65
1”OD25.4 x 1.65OD76.2 x 1.65
1-1/2”OD38.1 x 1.65OD101.6 x 1.65
2”OD50.8x 1.65
OD101.6 x 1.65
3”OD88.9 x 2.11OD152.4x 1.65
Note: Larger sizes available on request
Thermal Performance Data
Inner TubeSize
3/4” VIP1” VIP
1-1/2” VIP2” VIP3” VIP
Cool DownLosses, kJ/m
37.0655.0980.98
101.94188.61
Heat Leak,W/m0.310.430.540.720.98
Bayonet HeatLeak, W
1.92.73.96.19.0
Welded FieldJoint Leak, W
1.71.72.53.44.9
Note: Cool down losses & heat leaks from ambient temperature to 80K
DISTRIBUTED BY:5.11
CRYOGENIC PRODUCTS