45568954 Evolution A9100 BTS Outdoor Installation Manual

Alcatel BSS

Outdoor Evolution A9100 BTS

Installation Manual

BTS Document

Installation & Dismantling Manual

3BK 17137 0009 RJZZA Ed.08

Status RELEASED

Short title INS

All rights reserved. Passing on and copying of this document, useand communication of its contents not permitted without writtenauthorization from Alcatel/Evolium.

BLANK PAGE BREAK

2 / 86 3BK 17137 0009 RJZZA Ed.08

Contents

Contents

Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1 General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71.1 Hardware Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

1.1.1 Racks Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81.1.2 Weight and Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

1.2 Restrictions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91.3 Prerequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101.4 Initial State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101.5 Final State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111.6 Operating Principle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131.7 Time Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141.8 Information equired . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

2 Preliminary Checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

2.1 Before Leaving for the Site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182.2 Before Starting (On Arrival at the Site) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

3 Rack Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

3.1 Rack Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 203.2 Racks Dismantling (If Necessary for Transport) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

3.2.1 Cables Disconnecting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 213.2.2 Mechanical Dismantling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 243.2.3 Batteries Dismantling (If Necessary for Transport) . . . . . . . . . . . . . . . . . . . . . . . . . 25

3.3 Rack Transportation on Final Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 273.3.1 Manual Transportation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 273.3.2 Crane Transportation With Pallet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 273.3.3 Crane Transportation With Craning Bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

3.4 Rack Positioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 293.4.1 Case of Steel Construction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 293.4.2 Case of Concrete Foundation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 303.4.3 Case of Space Constraint at Right of BTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 313.4.4 Finishing Assembly (If Rack Dismantled) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

4 Power Supply and Earth Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

4.1 Cables Installation in the Cable Way . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 344.2 Cables Entry in BTS Plinth Cover Plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 354.3 Protective Earth Cable Connection (GND) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 364.4 AC 230 V Mains Power Supply Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 374.5 Batteries Installation (If Dismantled On Site) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 394.6 AC Power Supply Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

5 PCM Cables Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 455.1 Cable Installation in the Cable Way . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 465.2 Cables Passing at BTS Side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 475.3 Cables Connection at BTS Side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 495.4 Case of L907/ 4 - 120 Ohm Cable (Alcatel Kits) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 515.5 PCM Cables Other as L907 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 525.6 Case of FLEX3 75 Ohm Cables (Alcatel Kits) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

6 Antenna Jumpers Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 576.1 Antenna Connection General Scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 586.2 Jumper Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 596.3 Connection to the Head of Feeders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 616.4 Connect to the BTS Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

7 Alarm Cables Installation (Option) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 657.1 Cable Installation in the Cable Way (Option) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

3BK 17137 0009 RJZZA Ed.08 3 / 86

Contents

7.2 Installing Alarm Cables at BTS Side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 677.3 L907/4 Alcatel Cable Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

8 Synchronization Clock Installation (Option) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

8.1 Configuration of Cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 748.1.1 A9100 / G2 BTS Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 748.1.2 A9100 / A9100 Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

8.2 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

9 Finishing Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

Appendix A : Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

Appendix B : List of Kits and Consumable Supplies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83

Appendix C : List of Documents and Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

4 / 86 3BK 17137 0009 RJZZA Ed.08

Preface

Preface

Purpose This document describes how to install an outdoor Evolution A9100 BTSof ALCATEL BSS.

What’s New In Edition 08Update for document type, category and mnemonic.

In Edition 07DDF label reference change.

In Edition 06Updating for platform naming.

In Edition 05Editorial correction.

In Edition 04Removing of Compact BTS CPT1.

In Edition 03Modification of AC power cables wires color.

In Edition 02Adding Compact BTS (CPT1 & CPT2).

In Edition 01Creation.

Audience This document is intended for:

Installers

Site administrators

Supervisors

3BK 17137 0009 RJZZA Ed.08 5 / 86

Preface

Project managers

Field service technicians

Occasional users.

Assumed Knowledge You must have a basic understanding of the following:

Basic knowledge of Alcatel BSS equipment

Experience of electrical installation and cabling.

6 / 86 3BK 17137 0009 RJZZA Ed.08

1 General Information


This chapter provides general information about the principle of the operationand requirements for the procedure:

Hardware description

Restrictions

Prerequisite

Initial state

Final state

Operating principle

Time schedule

Information required.

3BK 17137 0009 RJZZA Ed.08 7 / 86


1.1 Hardware Description

1.1.1 Racks Configuration

Plinth Plinth

radio subrack

radio subrack

radio subrack

roof

radio subrack

Battery unit

ADAM

AC Switch unit

roof

OUTC

radiosubrack

AC Connection

Figure 1: CPT 2

Plinth Plinth

radio subrack

radio subrack

radio subrack

top roof top roof

Side compartment BTS

Battery unit

ADAM

Battery unit

Options

COAR

Batteryswitchs

AC Connection

AC Switch unit

Figure 2: MINI

8 / 86 3BK 17137 0009 RJZZA Ed.08


Plinth Plinth Plinth

radio subrack

radio subrack

radio subrackradio subrack

radio subrack

radio subrack

top roof top roof top roof

Side compartment BTS 1 BTS 2

Battery unit

ADAM

Battery unit

Options

COAR

Batteryswitchs

AC Connection

AC Switch unit

Figure 3: MEDI

1.1.2 Weight and Dimensions

Dimensions (mm) Average Weight (kg)

CPT 2 without option/without battery H = 1500

W = 1200

D = 700

380

MINI without option/without battery H = 1500

W = 1200

D = 700

300

MEDI without option/without battery H = 1500

W = 1800

D = 700

500

BTS2 Extension rack for MINI BTS H = 1500

W = 600

D = 700

200

Battery BU 41 (4 batteries) - 50

Battery BU 100 (4 batteries) - 120

1.2 RestrictionsNone.

3BK 17137 0009 RJZZA Ed.08 9 / 86


1.3 Prerequisites

The site conforms to the “Safety rules” of General Wiring Handbook

The site is ready to receive the rack, according to the SPP42

The equipment is delivered packed on site with associated kits

The following equipment are not mandatory installed before starting:Antenna feeders

1.4 Initial StateThe rack and installation kits are packed and delivered on site.

Figure 4: Concrete Foundation

10 / 86 3BK 17137 0009 RJZZA Ed.08


Figure 5: Street Construction

1.5 Final State

The rack is ready for commissioning

The rack is not powered up.

Figure 6: Field Installation on Concrete Foundation (Example MINI or CPT2)

3BK 17137 0009 RJZZA Ed.08 11 / 86


Figure 7: Building Installation on Steel Construction (Example MEDI)

12 / 86 3BK 17137 0009 RJZZA Ed.08


1.6 Operating Principle

Preparation before leaving for the site

Preparation on arrival at the site

Rack installation

Option: Rack dismantling for transport

Install the power supply and earth cables

Install PCM cables

Install antenna jumpers

Option: Install alarm cables

Option: Install synchronizatoin cables

Finish installation

... ... ...

... ... ...

To be done by Alcatel installation team

Can be done by the customer. If not, it is be acomplished by the installation team

OPTION:

LEGEND

According to customer demands,can be provided or not

3BK 17137 0009 RJZZA Ed.08 13 / 86


1.7 Time Schedule

Task Duration (mn)

1st person

Duration (mn)

2nd person

Before going on site (at base) 60 -

Preliminary tasks on site

- Packages unwrapping

- General checking

- Rack transportation on final location (1)

20

not included

20

not included

Installation with rack disassembling (2) 30 30

Installation without rack disassembling (2) 15 15

Battery removal and installation (option) 30 30

Installation of earth and power supply cables 30 30

Installation of PCM cables 15 -

Installation of antenna jumpers 30 30

Installation of alarm cables (option) 15 -

Installation of synchronization cables (option) - 15

Finishing installation 15 15

Total 260 185

(1) : Transportation time to final location depending of the site

(2) : Tasks where two persons are mandatory for execution

Mandatory 4 persons for manual transport of disassembled equipment

The given duration is based on :

Basic installation without options (alarm, synchronization, ...)

Technical constraint, not taking into account the safety parameter

14 / 86 3BK 17137 0009 RJZZA Ed.08


1.8 Information equiredSite

Address and access to the site (key holder)

Grounding plate location (GND)

Customer power supply cabinet location

Fuse breakers location in customer power supply cabinet

Antenna feeders connection and information (AZIMUTH, Sectors,...)

Rack precise location

Number of alarms to be connected (if the case)

Alarm terminal block location (if the case)

Rack

Type of BTS rack to be installed

Type of batteries (BU41, BU100)

Rack fixing (steel construction, concrete foundation)

Kits

PCM connection type

PCM cables impedance (120 ohm, 75 ohm)

Synchronization configuration (if the case)

3BK 17137 0009 RJZZA Ed.08 15 / 86


16 / 86 3BK 17137 0009 RJZZA Ed.08

2 Preliminary Checks


This chapter describes the preparation of the operation in two steps:

At base

On arrival at the site.

3BK 17137 0009 RJZZA Ed.08 17 / 86


2.1 Before Leaving for the Site

Check prerequisites fulfillment See Prerequisites (Section 1.3).

Check availability of informationrequired

See Information equired (Section 1.8) .

Check availability of documentation See List of Necessary Documents (in section C).

Check availability of tools See Installation Kits (in section B), refer to the ” Toolscatalogue ” for content checking.

Check availability of supplies See Consumable Supplies (in section B).

2.2 Before Starting (On Arrival at the Site)

Check applicable notification list andOperation Instructions

Refer to ITL “Applicable notifications list” for checking ifnotifications have to applied during the operation.

Refer to IO “Applicable operation instructions list” for checkingif operation instructions have to applied.

Check that safety instructions areapplied

Refer to “ General Wiring Handbook “ for checking that safetyprecautions have been taken into accordance with safetyinstructions.

Read instructions to be applied in caseof anomaly

Refer to “ General Wiring Handbook “ for instructions.

Fulfill premises inspection form andcompletion check list

Refer to CEL “ Premises inspection form “.

Fulfill completion check list Complete header field of the CCL

The CCL is completed as each installation instruction iscarried out.

Check availability of Alcatel kits See Installation Kits (in section B).

18 / 86 3BK 17137 0009 RJZZA Ed.08

3 Rack Installation

3 Rack Installation

This chapter describes how to:

Unpack the BTS rack

Dismantle the BTS rack (if necessary for transport)

Transport the rack

Position the BTS rack.

3BK 17137 0009 RJZZA Ed.08 19 / 86

3 Rack Installation

3.1 Rack Unpacking

1. Unpack the equipment

2. Check the delivery and report any damage to the carrier delivery note

3. Verify the type of rack and serial number

4. Locate the final location.

20 / 86 3BK 17137 0009 RJZZA Ed.08

3 Rack Installation

3.2 Racks Dismantling (If Necessary for Transport)

3.2.1 Cables Disconnecting

If case CPT2 : cables must be disconnected in rack 1 and rack 2

If case MINI : cables must be disconnected in BTS 1

If case MEDI : cables must be disconnected in BTS 1 and in BTS2

BTS1 Disconnecting for

MINI or MEDI

1. Disconnect Heating 230V (See Figure 8)

2. Disconnect 230V Service + light

3. Disconnect Alarms

4. Disconnect COAR power supply

5. Disconnect -48V Busbar power supply

6. Disconnect 0V Busbar power supply

7. Disconnect Earth (in side compartment)

8. Disconnect Abis to SUMP

9. Disconnect SUMP flat cable

COAR

A

BI

H

EF

G

C

D

Figure 8: MINI or MEDI Connection Between SIDE COMPARTMENT andBTS 1 (View From BTS 1)

3BK 17137 0009 RJZZA Ed.08 21 / 86

3 Rack Installation

BTS2 disconnecting for

MEDI only

1. Disconnect Subrack 6 power supply (See Figure 9)

2. Disconnect Subrack 5 power supply

3. Disconnect Subrack 4 power supply

4. Disconnect Heating 220V

5. Disconnect Door alarm

6. Disconnect Logic flat cable

7. Disconnect HEX2 (BTS2)

BTS1 BTS2A

B

C

E

F

D

G

Figure 9: MEDI Connection Between BTS 1 and BTS 2 (Front View)

Rack 2 Disconnecting

for CPT 2 Only

1. Disconnect Heating 230V (See Figure 10)

2. Disconnect 230V Service + light

3. Disconnect -48V blue wires

4. Disconnect 0V black wires

5. Disconnect internal alarm cable (15 pin male connector) (See Figure 11)

6. Disconnect Logic flat cable

22 / 86 3BK 17137 0009 RJZZA Ed.08

3 Rack Installation

A

B

C

D

Figure 10: CPT 2 Connection Between Rack 1 and Rack 2 (View From Rack 2)

OUTC

F

E

Figure 11: CPT 2Connection Between Rack 1 and Rack 2 onOUTC Board (View From Rack 1)

3BK 17137 0009 RJZZA Ed.08 23 / 86

3 Rack Installation

3.2.2 Mechanical Dismantling

Nr Materials Reference Kit

1 Dismantling tool 3BK 08898 AA Installation kit

1 2

34

5 6

1. Remove the 3 vandalismproof caps with screwdriver and the 3 screws withsupplied special tool (in document holder)

2. Remove the side panel by removing the 4 internal screws with spanner of 13

3. Roof removing of BTS2 (MEDI) or BTS1 (MINI)

4. Unscrew the BTS1 roof and remove it (MEDI)

5. Using specific tool, unscrew the racks (top view)

6. Disassemble the rack.

24 / 86 3BK 17137 0009 RJZZA Ed.08

3 Rack Installation

3.2.3 Batteries Dismantling (If Necessary for Transport)

F1

F2BAT BAT BATBAT

BAT BAT BAT BAT WARNING

!

TEMPERATURE +

−

Sensor

TEMPERATURE

12

34

5

3BK 17137 0009 RJZZA Ed.08 25 / 86

3 Rack Installation

1. Switch off F1 (and F2)

2. Take precaution against short circuit current when handling charged batteries

3. Disconnect cables

4. Sensor connection details

5. Dismantle exhausting hoses

6. Unfit the batteries.

26 / 86 3BK 17137 0009 RJZZA Ed.08

3 Rack Installation

3.3 Rack Transportation on Final Location

3.3.1 Manual Transportation

1 2

3

1. Manual transportation for a very short distance (see general safetyinstructions)

2. Rack transportation with pallet handling

3. MINI or CPT2 transportation with pallet handling.

3.3.2 Crane Transportation With Pallet

1 2

1. Handle by crane with straps. Leave the pallet to avoid doors damages

2. Handle by crane with straps (MEDI).

3BK 17137 0009 RJZZA Ed.08 27 / 86

3 Rack Installation

3.3.3 Crane Transportation With Craning Bar

Insert belts or slings before inserting rods bar into eyebolts - belts with 4 pointfastening should be used as a loading harnessCheck that max. tensile load per eyebolt is not exceeded: direction of pull a =45� to the screw axis 240 kg/eyebolt

Respect transport regulations:

single cabinet: fasten transport belts to all 4 eyebolts

MINI or MEDI cabinet: insert rods through eyebolts and attach to cranehook at minimum of 4 points

The bar and the fixing points are specified by Alcatel.The choice of straps (slings), hooks and crane are under responsibility ofcraning subcontractor.

1 2

3

12345671234567

12345671234567

12345671234567

12345671234567

12345671234567

4 5

1. Roof removing of BTS2 (MEDI) or BTS1 (MINI)

28 / 86 3BK 17137 0009 RJZZA Ed.08

3 Rack Installation

2. Unscrew the BTS1 roof and remove it (MEDI)

3. Bar and split pin 3BK 08804 AA

4. Crane connection and fixing points (MINI or CPT2)

5. Crane connection and fixing points (MEDI).

3.4 Rack Positioning

3.4.1 Case of Steel Construction


3 Bolt M12x80 1AD 00050 0123

5 Washer 12.4x24x1.6 1AD 00236 0006

6 Nut M12 1AD 00197 0008

Basic kit

(BKG3O)

12341234

12341234

1

2

123456789123456789

123412341234

1212

3

5

6

Figure 12: Leveling and Fixing on Steel Construction

Procedure 1. Assemble the racks using same principle of dismantling

2. Position the BTS

3. Level the racks using spanner of 19 (1 of figure 12)

4. Block the leveling feet nuts using spanner of 19 (2 of figure 12)

5. Fix the racks to the concrete foundation (3- 4 - 5 - 6 of figure 12)

3BK 17137 0009 RJZZA Ed.08 29 / 86

3 Rack Installation

3.4.2 Case of Concrete Foundation


3 Wall plug 1AD 01847 0003

4 Bolt M12x80 1AD 00050 0123

5 Washer 12.4x24x1.6 1AD 00236 0006

Basic kit

(BKG3O)

123451234

1

2

3

4

5

Figure 13: Leveling Feet and Concrete Foundation Fixing

Procedure 1. Assemble the racks using same principle of dismantling

2. Mark the position of fixing points on the foundation (See Figure 14)

3. Drill fixing holes (4 holes)

4. Insert wall plugs with screws into the holes (See Figure 13)

5. Tighten a little and remove the screws

6. Position the BTS

7. Level the racks using spanner of 19 (1 of Figure 13)

8. Block the leveling feet wit nuts with spanner of 19 (2 of Figure 13)

9. Fix the racks to the concrete foundation (3 - 4 - 5 of Figure 13)

30 / 86 3BK 17137 0009 RJZZA Ed.08

3 Rack Installation

1150 mm

1750 mm

500 mm

500 mm

22.5 mm

625 mm

72.5mm

1150 mm

500 mm

22.5 mm

72.5 mm

85 mm

20 mm

MINI or MEDI

CPT 2

Figure 14: Mark Position on Foundation

3.4.3 Case of Space Constraint at Right of BTS

If there is no place between right BTS compartment and the wall, it is necessaryto use specific tools :

ratchet + short tool : 3BK 08899 AA

long extension + socket : 3BK 08898 AA (can be left in the BTS cabinet)

3BK 17137 0009 RJZZA Ed.08 31 / 86

3 Rack Installation

100 mm

12121212121212121212121212121212121212

123456789012345612345678901234561234567890123456123456789012345612345678901234561111111111111111111111234567890123456123456789012345612345678901234561234567890123456

121212121212121212121212121212121212121212

12341234123412341234

1234123412341234

Clearanceconstraint

Guide

Guide

BTS

123456789012345678901234567123456789012345678901234567123456789012345678901234567123456789012345678901234567123456789012345678901234567123456789012345678901234567123456789012345678901234567123456789012345678901234567123456789012345678901234567123456789012345678901234567123456789012345678901234567123456789012345678901234567123456789012345678901234567123456789012345678901234567123456789012345678901234567123456789012345678901234567123456789012345678901234567123456789012345678901234567123456789012345678901234567123456789012345678901234567123456789012345678901234567123456789012345678901234567123456789012345678901234567123456789012345678901234567123456789012345678901234567123456789012345678901234567123456789012345678901234567123456789012345678901234567123456789012345678901234567123456789012345678901234567123456789012345678901234567123456789012345678901234567123456789012345678901234567123456789012345678901234567123456789012345678901234567123456789012345678901234567123456789012345678901234567123456789012345678901234567123456789012345678901234567123456789012345678901234567

Figure 15: Specific Rack Assembling Tools

3.4.4 Finishing Assembly (If Rack Dismantled)

To finish the assembly:

1. Connect all cables as reverse method of disconnecting

2. Assemble batteries (if dismantled).

32 / 86 3BK 17137 0009 RJZZA Ed.08

4 Power Supply and Earth Installation


This chapter describes the procedure to:

Install power cables in the cable tray

Connect protective earth cable (GND)

Connect the 230 V mains power supply cables

Install the batteries

Test the power supply installation.

Before making any electrical connections to the rack, ensure that the safetyinstructions are applied.

It is essential that:

the electrical power supply is disconnected. Ensure that all switches or fuses

devoted to the new RACK into the site connection box are switched OFF

due to the high leakage current, the protective EARTH must be connectedto the equipment before AC or DC power cable connection.

3BK 17137 0009 RJZZA Ed.08 33 / 86


4.1 Cables Installation in the Cable Way


1 Tie wraps 1AD 00698 0001 Consumable supplies

2 GND cable Y/G 1 x 16 mm2 3BK 08957 xx

3 AC 230V power cable:

- 2 x 4 mm2 (1 phase system)

- 5 x 6 mm2 (3 phase system)

-

3BK 08943 xx

3BK 08944 xx

Installation kit

1m

1 2

3 4

1. Install yellow / green cable in power compartment of cable tray

2. Install AC power cable in power compartment of cable tray

3. Attach cable with plastic tie wraps

4. Cut the cables at good length.

34 / 86 3BK 17137 0009 RJZZA Ed.08


4.2 Cables Entry in BTS Plinth Cover Plate


1 Tie wraps 1AD 00689 0001

2 Shrink sleeves 1AC00057 0102

Consumable supplies

1 2

AC GND

3

4

1. Install cover plate (with holes) in front of cable tray

2. Insert 20 cm of 40/13 shrink sleeve on cables

3. Pass cables through cover plate

4. Heat the shrink sleeve.

3BK 17137 0009 RJZZA Ed.08 35 / 86


4.3 Protective Earth Cable Connection (GND)


1 Lug ring crimp ∅ 8 /50 mm2 1AB 03205 0071

2 Tie wraps 1AD 00698 0001

Consumable supplies

3 GND cable Y/G 1x50 mm2 3BK 08961 xx Installation kit

+−

123456789012345678123456789012345678123456789012345678123456789012345678123456789012345678123456789012345678123456789012345678123456789012345678123456789012345678123456789012345678123456789012345678123456789012345678123456789012345678

GND

1 2

3 4

1. Crimp a ∅ 8 terminal lug at BTS side and crimp an adapted lug at siteextremity of GND cable

2. Connect the GND cable to the site earth plate

3. Connect earth cable to the stud in the plinth (8mm)

4. Detail of GND cable connection.

36 / 86 3BK 17137 0009 RJZZA Ed.08


4.4 AC 230 V Mains Power Supply Connection


1 Set of wire terminal 1AB 05067 0004 Basic kit


+−

AC filter BOX

Figure 16: AC Filter Box Position

Procedure 1. Cut the cable at good length and prepare head of cable

2. Cut 3 cm of external insulation at cable gland passage

3. Pass cable trough cable gland

4. Put a shrink sleeve on cable at end of external insulation

5. Fit a wire terminal on each wire

6. Connect cables to clamp bridge in the AC filter box

7. Close the cover of AC filter box

3BK 17137 0009 RJZZA Ed.08 37 / 86


Figure 17: Fit Wire Terminal

Earth (GND) Yellow / Green

Neutral (N) (L1) Blue

Phase 1 Black

Phase 2 (L2) Brown

Phase 3 (L3) Red

121212

L1L2L3

NPE

LIG

HT

NIN

G P

RO

TE

CT

ION

L1L2

L3N

AC 230V FILTERS

Figure 18: MINI / MEDI / CPT 2 : 3 Phase System – Remove Bridge ( If Present )

38 / 86 3BK 17137 0009 RJZZA Ed.08


121212

L1L2L3

NPE

LIG

HT

NIN

G P

RO

TE

CT

ION

L1L2

L3N

BRIDGE

AC 230V FILTERS

Figure 19: MINI / MEDI / CPT 2 : 1 Phase System– connect bridge between L1, L2, and L3– insulate the unused wires ( do not cut them off )

4.5 Batteries Installation (If Dismantled On Site)The BTS can be equipped by factory either with BU41 or BU100 batteries. Thisprocedure is only applied after site dismantling (because transportation).

The weight of each element of battery BU100 is 30 kg. Apply safety rules

to carry it

Use insulated tools when connecting

Batteries are delivered in fully charged status.

Procedure 1. Put the batteries in the compartment at bottom of rack (See Figure 16)

2. Put spacers between batteries

3. Fix the batteries to the rack with strap (See Figure 20)

4. Connect the cables between the elements of batteries (See Figure 21or Figure 22)

5. Connect positive and negative cables to the battery pack

6. Connect the temperature sensor to the positive of battery pack

7. Use protective covers to insulate terminals.

3BK 17137 0009 RJZZA Ed.08 39 / 86


121211212111212

BuckleStrap

Batteries

1211111

12121212

Figure 20: Strap Installing

Sensor

Figure 21: BU41 Cabling

40 / 86 3BK 17137 0009 RJZZA Ed.08


123456789012345678901234567123456789012345678901234567123456789012345678901234567

RED

1212

Fixing straps

6 spacers

Nut M6

M6 terminal stud

4 x cap

4 x cap3 x battery connector

Springwasher M6

Washer M6

M8−M6terminal stud

M6 terminal studHex screwM8 x 15

Spring washer M8

Washer M8

Battery connector

Sensor

Figure 22: BU100 Cabling

3BK 17137 0009 RJZZA Ed.08 41 / 86


4.6 AC Power Supply Testing

N P

AC230V

N P

N P

V

N P

V

7

65

43

21

1. At site power cabinet: check if 230 V fuse breakers are switched off

2. At rack side: using an ohmmeter, check that there is no short circuit betweenphase and neutral

3. At rack side: do the same test between protective earth (green / yellowwire) and each 230 V wire

42 / 86 3BK 17137 0009 RJZZA Ed.08


4. At site power cabinet: switch on the 230 V fuse breakers

5. At rack side: check that the 230 V voltage between phase and neutralis present

6. At rack side: using phase tester, check that the phase wire is connectedat good connection point

7. At site power cabinet: switch off the fuse breakers.

3BK 17137 0009 RJZZA Ed.08 43 / 86


44 / 86 3BK 17137 0009 RJZZA Ed.08

5 PCM Cables Installation


This chapter describes the procedure to:

Install PCM cables in the site cable tray

Connect PCM cables to the connection area of the rack.

3BK 17137 0009 RJZZA Ed.08 45 / 86


5.1 Cable Installation in the Cable Way


1 Label 3BK 08062 ABAA Basic kit


3 PCM cable:

- either L907/ 8 (120 - ohm)

- or FLEX3/ 8 (75 - ohm)

-

3BK 08942 xx

3BK 25240 xx

Installation kit

1m

Abis 2

Abis 1

1 2

34

1. Install cables in PCM compartment

2. Attach cables with plastic cable ties

3. Mark cables with a marker

4. Label cable with supplied labels.

46 / 86 3BK 17137 0009 RJZZA Ed.08


5.2 Cables Passing at BTS Side


1 Shrink sleeve 40 / 13 1AC 00057 0102 Consumable supplies

2 Shrink sleeve 16 / 5 8BC180023528

3 Reduction 32 / 13 8BC180027133 Basic kit

3BK 17137 0009 RJZZA Ed.08 47 / 86


6 7

1. Pass 20 cm of 40 / 13 and 16 / 5 shrink sleeves then the plastic reductionon the cables

2. Pass cables through plinth cover plate

3. Strip the cable at cable gland level

4. Pass the cable trough the cable gland

5. Pass PCM cables trough cable gland on BTS bottom plate

6. Fit plastic reduction then 40 / 13 shrink sleeve then heat the shrink sleeve

7. Fit and heat the 16 / 5 shrink sleeve.

48 / 86 3BK 17137 0009 RJZZA Ed.08


5.3 Cables Connection at BTS Side

Abis KRONE(inserting)

Abis (screwing)

Figure 23: MEDI or MINI COAR Board

3BK 17137 0009 RJZZA Ed.08 49 / 86


Abis KRONE(inserting)

Abis (screwing)

Figure 24: CPT 2 OUTC Board

50 / 86 3BK 17137 0009 RJZZA Ed.08


5.4 Case of L907/ 4 - 120 Ohm Cable (Alcatel Kits)Only one cable is used to carry Abis1 & Abis2 signals.

Color KRONE

inserting connector

Signal

Quad 1 white 8 Abis 1 / TX

(output high grey 8 Abis 1 / TX

level signal) blue 6 Abis 2 / TX

violet 6 Abis 2 / TX

Quad 2 yellow 7 Abis 1 / RX

(input low level grey 7 Abis 1 / RX

signal going brown 5 Abis 2 / RX

toward BSC) violet 5 Abis 2 / RX

A

B

E

F

G

D L 9 0 7

1 A C 0 1 3 2 8 0 0 0 4

ML

100 mm

10 mm123123

1

A : String

B : Cable drain (GND)

D : Cable

E : Cable braid

F : Transparent film

G : Aluminium foil

3BK 17137 0009 RJZZA Ed.08 51 / 86


87

65

4

RX

TX

RX

TX 8

1

1

8

2 3

Figure 25: Connection Detail

1. Prepare head of cable

2. Remove the lightning protection before cabling. Insert it after wiresconnection

3. Using inserting tool connect to the KRONE connector:

Braid must be squeezed in the bridge

3 jumpers must be removed from Abis 1 and Abis 2 green connectors(they are used only in 75-ohm connection)

5.5 PCM Cables Other as L907If cables are not Alcatel L907/4, then the wires must have right specificationsfor inserting in the KRONE connector. If not, the wires have to be connected tothe screwing connectors of board.

52 / 86 3BK 17137 0009 RJZZA Ed.08


AB

IS1

AB

IS2

11

TX

R

XT

X

RX

88

Figure 26: Example : connection to screwing connectors of COAR or OUTCboard. The 3 jumpers must be removed from the connectors (they are usedonly in 75-ohm connection)

1 GND braid earthing clamp

2 TX

3 TX

BTS output signal

going toward BSC

4 GND drain wires

5 RX

6 RX

BTS input signal

coming from BSC

7 R200 (not used)

8 GND braid earthing clamp

Table 1: Screwing Connector Pin Assignment

3BK 17137 0009 RJZZA Ed.08 53 / 86


5.6 Case of FLEX3 75 Ohm Cables (Alcatel Kits)

BG

D

K

A

F

H

E

I

C

J

50 mm

10 mm123123

1

A : Transparency film

B : DRAIN of cable

C : Braid of coaxial

D : Multi-coaxial cable

E : Braid of cable

F : DRAIN of coaxial

G : Aluminium

H : Core of coaxial

I : Skin of coaxial

J : Core insulation

K : Number of coaxial

12

34

56

7

123123

1234567812345671234567

2

1. Prepare head of FLEX 3 cable

2. Mount the earthing clamp.

54 / 86 3BK 17137 0009 RJZZA Ed.08


Coaxial Connector Pin Remarks

1 Abis 1 (TX) 2

3

braid

inner conductor

2 Abis 1 (RX) 5

6

braid

inner conductor

3 Abis 2 (TX) 2

3

braid

inner conductor

4 Abis 2 (RX) 5

6

braid

inner conductor

For each connector:

- wire bridge from pin 1 to pin 2



3BK 17137 0009 RJZZA Ed.08 55 / 86


56 / 86 3BK 17137 0009 RJZZA Ed.08

6 Antenna Jumpers Installation


This chapter describes how to connect the antenna jumpers between feedersand BTS rack.

3BK 17137 0009 RJZZA Ed.08 57 / 86


6.1 Antenna Connection General Scheme

Label:

Label:

Ant A

Ant A

Ant AAnt B

Ant B

Ant B

230

90

45

A B A A BB

NORTH

ANT BAZIMUTH

125

SECT: NANT A

MBS

AB B BAA

A A AB BB

N QPANX ANXANX

Figure 27: Example of Antenna Cabling and Labeling (3 Sectors)

58 / 86 3BK 17137 0009 RJZZA Ed.08


6.2 Jumper Installation


1 Labels 3BK 08062 ABAA Basic kit

2 Tie wraps 1AD 00698 0001

3 Shrink sleeve 40/13 1AC 00057 0102

4 Shrink sleeve 63/19 1AC 00057 0103

Consumable supplies

5 Plastic reduction 55/32 8BC 18002 7134 Basic kit

6 Antenna jumper cable 3BK 05360 xx Installation kit

Figure 28: General View of Jumper Mounting

3BK 17137 0009 RJZZA Ed.08 59 / 86


NAnt A

Azimut 30°Ant 1

Jumper labelFeeder label

Jumpers

N P Q

A

B

40

55/32

1363 19

Jumper

1 2

3 4

56

1. Label the jumpers

2. Plinth cover with cable bushes

3. Put 20 cm of 63 / 19 and 40 / 13 shrink sleeves and the reduction oneach jumper

4. Fit and heat the 40 / 13 shrink sleeve on the jumper

5. Fit and heat 63 / 19 shrink sleeve

6. Passing detail.

60 / 86 3BK 17137 0009 RJZZA Ed.08


6.3 Connection to the Head of Feeders

If the feeders are not labeled:

Inform the customer

Don’t connect the jumpers

Fulfill the CCL.


1 Vinyl electrical tape 1AC 01556 0001

2 Tie wrap 1AB 00414 0006

3 Tape “auto-vulcanisant” 1AC 01595 0001

Basic kit

(BKGO)

123123123121234561234123412 123412 1212312 12312 121212

1234123412 1234123 1234123 1231234 123121234 12312345

123451234123412345 12312345 123412341231231234123412 1212345 12312345 123

112345 12123456 12312 12312 12312 12312341234

12345612345612 12312 1212312 121231234123412345612345612312123123

1 23Feeder Jumper

Figure 29: Water Proof the Connections

Procedure 1. Connect the antenna jumpers to the feeders, start by the most difficultconnector to access (See Figure 28)

2. Verify the connectors

3. Screw connector male with connector female

4. Tighten the screw manually then shake cables a little

5. Using Alcatel tightening tool tighten with firmness

6. Fit the “Auto-vulcanisant” rubber tape (3) (See Figure 29)

7. Fit the vinyl electrical tape over the “auto-vulcanisant” tape (1)

8. Secure with tie wraps to avoid tape removing (2)

3BK 17137 0009 RJZZA Ed.08 61 / 86


6.4 Connect to the BTS Rack


1 Tie wraps with braid 1AD 00698 0001 Consumable supplies

BTS1 / BTS2

Pant A

Pant B

Qant A

Qant B

Nant A

Nant B

Figure 30: MINI or MEDI Bottom of BTS Cabinet

Antennas

Back of rack

AC Filterand

connection box

Batteries

Figure 31: CPT 2 Bottom of Rack 1

Procedure 1. Ensure that the radius of each cable is at least 3 cm

2. Refer to Information equired (Section 1.8) for cable connections (SeeFigure 30)

3. Fit connector male with connector female

62 / 86 3BK 17137 0009 RJZZA Ed.08


4. Tighten the screw manually then shake cables a little

5. Using tightening tool, tighten with firmness

6. Use tie wraps to bundle the jumpers together

3BK 17137 0009 RJZZA Ed.08 63 / 86


64 / 86 3BK 17137 0009 RJZZA Ed.08

7 Alarm Cables Installation (Option)


This chapter describes how to:

Install alarm cables in the cable way

Connect alarm cables to the rack.

3BK 17137 0009 RJZZA Ed.08 65 / 86


7.1 Cable Installation in the Cable Way (Option)



2 Labels 3BK08062ABAA Basic kit

3 PCM cable L907 / 4 3BK 08942xx Installation kit

1m

Alarm

1

1 2

3 4

1. Install cables in special compartment of cable tray

2. Attach cables with plastic tie wraps

3. Mark cables with a marker

4. Label cable with supplied labels.

66 / 86 3BK 17137 0009 RJZZA Ed.08


7.2 Installing Alarm Cables at BTS Side


1 Shrink sleeve 40 / 13 1AC 00057 0102

2 Shrink sleeve 16 / 5 8BC 18002 3528

Consumable supplies

3 Reduction 32 / 13 8BC 18002 7133 Basic kit

3BK 17137 0009 RJZZA Ed.08 67 / 86


AB

IS 1

AB

IS 2

EXT − ALARMS

Alarms

18

7

12

45

67

8 Alarm n°10Alarm n°13

Alarm n°14

1 : GND (braid earthing clamp)

2 : ALM1 GND

3 : ALM 1 (external alarm nr 10)

4 : ALM 2 GND


6 : ALM 3 GND

68 / 86 3BK 17137 0009 RJZZA Ed.08



8 : GND (braid earthing clamp)

Figure 32: Connector Pin Assignment

8 9

10 11

1. Pass 20 cm of 40 / 13 and 16 / 5 shrink sleeves then the plastic reductionon the cables

2. Pass cables through plinth cover plate

3. Strip the cable at cable gland level

4. Pass the cable trough the cable gland

5. Pass cable trough cable gland on BTS bottom plate

6. Prepare head of cable

7. Connect cable on COAR board

8. Example with 3 cables for 3 alarms

9. Example with 1 cable for 3 alarms

10. Fit reduction 32 / 13 and the 40 / 13 shrink sleeve then heat shrink sleeve

11. Fit and heat the 16 / 5 shrink sleeve.

3BK 17137 0009 RJZZA Ed.08 69 / 86


40

Reduction32/13 13 16 5

Cable

Figure 33: Cross Section

7.3 L907/4 Alcatel Cable Description

A

B

E

F

G

D L 9 0 7

1 A C 0 1 3 2 8 0 0 0 4

Pair 2

Pair 1

Pair 2

Pair 1

I

H

brown

violet

yellow

grey

blue

violet

white

grey

Quad2

Quad1

ML

A : String

B : Cable DRAIN (earth)

D : Cable

E : Braid of cable

F : Transparency film

G : Aluminium

H : Quad of wires Number 1

I : Quad of wires Number 2

Figure 34: Prepare Head of Cable

70 / 86 3BK 17137 0009 RJZZA Ed.08


Pair Alarm No Color

1 Alarm 1 white

grey

Quad 1

2 Alarm 2 blue

violet

3 Alarm 3 yellow

grey

Quad 2

4 not used brown

violet

3BK 17137 0009 RJZZA Ed.08 71 / 86


72 / 86 3BK 17137 0009 RJZZA Ed.08

8 Synchronization Clock Installation (Option)


This chapter describes how to install and connect the synchronization cablesbetween the new rack and the other BTS on site (option).

3BK 17137 0009 RJZZA Ed.08 73 / 86


8.1 Configuration of Cabling

8.1.1 A9100 / G2 BTS Connection

G3/G4 COARXCLC 1 out

Master Slave

CLK inSTSE viaCOB2

G2

G3/G4COARXCLC 1 in

Master Slave

CLK out MBSR via COB2

G2

74 / 86 3BK 17137 0009 RJZZA Ed.08


59

4

8

3

7

2

6

P1

59

4

8

3

7

2

6

P2

screen

screen

white

brown

green

yellow

grey

pink

blue

red

COAR COB2

OCC23 3BK 08303 AAFigure 35: Synchronization Cables for A9100 Evolution / G2 BTS Connection

8.1.2 A9100 / A9100 Connection

G3/G4 COARXCLC 1 out

Master Slave

G3/G4COARXCLK 1 in

3BK 17137 0009 RJZZA Ed.08 75 / 86


59

4

8

3

7

2

6

P1

59

4

8

3

7

2

6

P2

screen

screen

white

brown

green

yellow

grey

pink

blue

red

COAR 1 COAR 2

OCC33 3BK 08304 AAFigure 36: Synchronization Cables for A9100 / A9100 BTS Connection

8.2 Installation


1 Labels 3BK08062AB Basic kit

2 Cable for clock synchronization:

∇ A9100/G2-BTS (10 m)

∇ A9100/A9100 (10 m)

-

3BK 08303 AA

3BK 08304 AA

Installation kit

Procedure 1. Choose the good configuration

2. Pass the synchronization cables in the site cable way

3. Label the cables with supplied labels

4. Dismantle SubD 9 connectors (write down the wire colors)

5. Pass the cables through the BTS bottom plate

6. Put back the SubD 9 connectors

7. Connect cables to the coreponding sockets of connection area (SeeFigure 37)

8. Fasten the connectors with knurled screws

76 / 86 3BK 17137 0009 RJZZA Ed.08


AB

IS 1

AB

IS 2

18

18

Synchro

18

18

Figure 37: Example : Synchronization Cables Connection to COAR

3BK 17137 0009 RJZZA Ed.08 77 / 86


78 / 86 3BK 17137 0009 RJZZA Ed.08

9 Finishing Installation


This chapter describes:

The labeling of the rack

Cleaning up

3BK 17137 0009 RJZZA Ed.08 79 / 86


BT S ST A TI ON 4

BTS STATION 4

1

2

3

4

1. Fit the "BTS STATION" and "N" labels at head of the BTS

2. Close unused ducts of plinth cover by using supplied caps

3. Clean the site

4. Give the key to the site responsible.

80 / 86 3BK 17137 0009 RJZZA Ed.08

Appendix A : Abbreviations

Appendix A: Abbreviations

Abis Link between BTS and BSC

AC Alternating Current

BATS Battery Small unit

BSC Base Station Controller

BSS Base Station Subsystem

BTS Base Transceiver Station

BU41 40 Amps battery unit

BU100 100 Amps battery unit

CCL Completion Check List

CEL Premises inspection form

DC Direct Current

EMS Cable clamp earthing and support assembly

FRD Failure report

GND Ground (earth)

GSM Global System for Mobile communication

ITL-PRO Procedure Technical and support information

IO Instruction Operation

MODEM MODulator - DEModulator

PCM Pulse Code Modulation

3BK 17137 0009 RJZZA Ed.08 81 / 86

Appendix A : Abbreviations

82 / 86 3BK 17137 0009 RJZZA Ed.08

Appendix B : List of Kits and Consumable Supplies

Appendix B: List of Kits and Consumable SuppliesInstallation Kits The following table is used to check, on site, the mandatory or optional delivery

item kits.

The used symbols are:

• mandatory kit

∇ technical choice kit

◊ customer option kit

Mandatory kits Mnemo Reference Qty

• Basic installation kit BKG3O 3BK 08107 AC 1

• Antenna jumpers cables BLF3 3BK 05360 DA 2/s

◊ 2 Mbits cables:

∇ 120 ohm - 4 pairs - L907/ 4 (roll 100 m)

∇ 75 ohm - 4 coax FLEX3/ 4 (roll 100 m)

-

CA120S4

CACOAX4

-

3BK 08942 xx

3BK 08940 xx

roll

◊ GND cable Y/ G 1 x 16 mm2 PC50YG1D 3BK08961 xx roll

◊ AC 230 Volts power cable

∇ 3 x 2.5 mm2 100 meters

∇ 5 x 6 mm2 250 meters

-

PC03G25

PC05B5

-

3BK25561 xx

3BK08944 xx

-

roll

roll

◊ Cable for clock synchronization

∇ A9100 / A9100 (10 m)

∇ A9100 / G2-BTS (10 m)

-

OCC33

OCC23

-

3BK 08304 AA

3BK 08303 AA

-

1

2

◊ Alarm cable 4 pairs - L907/ 4 CA120S4 3BK 08942 xx roll

◊ Dismantling tool - short part (left in cabinet) DISMSP 3BK 08898 AA 2

◊ Mechanical part for 24 terminal blocks MP24 1AD 02843 0001 1

◊ Label for 24 terminal blocks LAB 1AD 02853 0001 1

◊ CAD Alcatel terminal blocks JS10 1AD 06634 0011 4

◊ DDF fixing kit for wall FKW 1AD 02844 0001 1

◊ Jumpers for DDF

∇ 120 ohm 1 pair

∇ 75 ohm 1 coax FLEX3 (roll 100 m)

-

CA120S

CACOAX1

-

3BK 08941xx

3BK 08939 xx

-

4 m

4 m

3BK 17137 0009 RJZZA Ed.08 83 / 86

Appendix B : List of Kits and Consumable Supplies

Consumable Supplies The following table is used to check, at base, the availability of the installer’sconsumable supplies (not included in Alcatel kits).

Item Qty

Indelible markers 1

Set of rubber sleeves for all cables 1

Ruber tape 1/ jumper

Electrical scotch 2

Set of Shrink sleeves 1

Tie wraps 5 mm x 300 mm 100

84 / 86 3BK 17137 0009 RJZZA Ed.08

Appendix C : List of Documents and Tools

Appendix C: List of Documents and ToolsList of Necessary

Documents

The following table is used to check, at base, the availability of the necessarydocuments.

Applicable notification list (ITL-PRO) 3DF 00462 0004 AAAGA

Applicable operation instructions (IO) 3DF 00300 0004 UAZZA

General wiring handbook 3BK 17160 0001 RJZZA

Tools catalogue for field activity 3BK 20458 0001 RJZZA

Site premises inspection form (CEL) 8BL 00704 0015 DRBRA

Completion Check List (generic) (CCL) 3BK 17200 0002 QZZZA

Specification for site preparation (SPP42) 8BL 00704 0059 DRBRA

BSS site premises inspection, post handover 8BL 00704 0016 DRBRA

List of Necessary Tools The following table is used to check, at base, the availability of the necessarytools (See ” Tools catalogue ” for content checking).

Kit name Reference Calibration

Basic kit OUT 001 no

BTS specific tools OUT 003 no

A9100 outdoor FVBA / Evolution BTS specifictools

OUT 007 no

3BK 17137 0009 RJZZA Ed.08 85 / 86

Appendix C : List of Documents and Tools

BLANK PAGE BREAK

86 / 86 3BK 17137 0009 RJZZA Ed.08

45568954 Evolution A9100 BTS Outdoor Installation Manual

Documents

Transcript of 45568954 Evolution A9100 BTS Outdoor Installation Manual