313 Seven Hills Road, Seven Hills - Blacktown City Council...313 Seven Hills Road,Seven Hills 3m...
Transcript of 313 Seven Hills Road, Seven Hills - Blacktown City Council...313 Seven Hills Road,Seven Hills 3m...
SYDNEY A: 9 Sarah St Mascot NSW 2020 T: (02) 8339 8000 F: (02) 8338 8399
SYDNEY MELBOURNE BRISBANE CANBERRA LONDON DUBAI SINGAPORE GREECE
ABN: 11 068 954 343
The information in this document is the property of Acoustic Logic Consultancy Pty Ltd ABN 11 068 954 343 and shall be returned on demand. It is issued on the condition that, except with our written permission, it must not be reproduced, copied or communicated to any other party nor be used for any purpose other than that stated in particular enquiry, order or contract with which it is issued.
I:\Jobs\2017\20170549\20170549.1\20170512RLA_R0_DA Acoustic Assessment.docx 1
MANAGING DIRECTORS MATTHEW PALAVIDIS VICTOR FATTORETTO DIRECTORS MATTHEW SHIELDS BEN WHITE
MANAGING DIRECTORS
MATTHEW PALAVIDIS
VICTOR FATTORETTO
GENERAL MANAGER
MATTHEW SHIELDS
313 Seven Hills Road, Seven Hills
DA Acoustic Assessment
I:\Jobs\2017\20170549\20170549.1\20170512RLA_R0_DA Acoustic Assessment.docx 2
DOCUMENT CONTROL REGISTER
Project Number 20170549.1
Project Name 313 Seven Hills Road, Seven Hills
Document Title DA Acoustic Assessment
Document Reference 20170549.1/1205A/R0/RL
Issue Type Email
Attention To John Harrison
Revision Date Document Reference Prepared By
Checked By
Approved By
0 12/05/2017 20170549.1/1205A/R0/RL RL BW
I:\Jobs\2017\20170549\20170549.1\20170512RLA_R0_DA Acoustic Assessment.docx 3
TABLE OF CONTENTS
1 INTRODUCTION 4 2 SITE PROPOSAL 4 3 EXISTING ACOUSTIC ENVIRONMENT 6 4 TRAFFIC NOISE INTRUSION 7
4.1 TRAFFIC NOISE CRITERIA 7 4.1.1 Blacktown City Council DCP 7 4.1.2 Australian Standards AS2107-2016 7
4.2 TRAFFIC NOISE ASSESSMENT 7 4.2.1 Unattended noise monitoring 7 4.2.2 Attended noise measurements 7
4.3 RECOMMENDED CONSTRUCTIONS 8 4.3.1 Glazed Windows and Doors 8 4.3.2 Walls and Roofs 9
5 NOISE EMISSION ASSESSMENT 10 5.1 BACKGROUND NOISE MONITORING 10 5.2 ACOUSTIC CRITERIA 11
5.2.1 Blacktown City Council DCP 2013 11 5.2.2 NSW EPA Industrial Noise Policy 11
5.2.2.1 Intrusiveness Criterion 11 5.2.2.2 Amenity Criterion 12
5.2.3 Protection of the Environment Operations Act Regulation 13 5.3 NOISE EMISSION ASSESSMENT 13
5.3.1 Underground Carpark Entry 13 5.4 RECOMMENDATIONS 14
5.4.1 Mechanical Plant Items 14 5.4.2 Management controls 14
6 CONCLUSION 15 APPENDIX 1 - UNATTENDED NOISE MONITORING DATA 16
I:\Jobs\2017\20170549\20170549.1\20170512RLA_R0_DA Acoustic Assessment.docx 4
1 INTRODUCTION
Acoustic Logic Consultancy (ALC) have been engaged to conduct an acoustic assessment of potential noise impacts associated with the proposed residential development to be located at 313 Seven Hills Road, Seven Hills.
ALC have utilised the following documents and regulations in the assessment of noise emanating from the development:
Blacktown City Council DCP;
NSW EPA Industrial Noise Policy (INP);
Australian and New Zealand AS/NZS 2107:2016 ‘Recommended design sound levels and reverberation times for building interiors’.
ALC confirms that the development can comply with all of the aforementioned authorities and standards on the proviso that the acoustic treatments nominated in this report are adopted.
This assessment has been conducted using the architectural drawings submitted to ALC by Cristina Gomes Architecture and Design and dated April 2017.
2 SITE PROPOSAL
The subject site is located on Seven Hills Road which is a four-lane road with medium to high traffic volumes.
It is proposed to construct ten two-storey townhouses with a basement level for car parking.
The site is bounded by Seven Hills Road to the north-west, by residential properties to the southeast and southwest, and by the Seven Hills North Public School to the northeast.
Refer to Figure 1 below, which is an aerial photo of the existing development.
I:\Jobs\2017\20170549\20170549.1\20170512RLA_R0_DA Acoustic Assessment.docx 5
Figure 1: Site Survey and Monitoring Location
Unattended noise measurement location Attended noise measurement location Subject site Potentially affected residential properties Seven Hills North Public School
I:\Jobs\2017\20170549\20170549.1\20170512RLA_R0_DA Acoustic Assessment.docx 6
3 EXISTING ACOUSTIC ENVIRONMENT
The existing acoustic environment is categorised by traffic noise levels from Seven Hills Road.
Traffic noise constantly varies in level, due to fluctuations in traffic speed, vehicle types, road conditions and traffic densities. Accordingly, it is not possible to accurately determine prevailing traffic noise conditions by measuring a single, instantaneous noise level. To accurately determine the effects of traffic noise a 15-20 minute measurement interval is utilised. Over this period, noise levels are monitored on a continuous basis and statistical and integrating techniques are used to determine noise description parameters. These parameters are used to measure how much annoyance would be caused by a particular noise source.
In the case of environmental noise three principle measurement parameters are used, namely L10, L90 and Leq.
The L10 and L90 measurement parameters are statistical levels that represent the average maximum and average minimum noise levels respectively, over the measurement intervals.
The L10 parameter is commonly used to measure noise produced by a particular intrusive noise source since it represents the average of the loudest noise levels produced by the source.
Conversely, the L90 level (which is commonly referred to as the background noise level) represents the noise level heard in the quieter periods during a measurement interval. The L90 parameter is used to set the allowable noise level for new, potentially intrusive noise sources since the disturbance caused by the new source will depend on how audible it is above the pre-existing noise environment, particularly during quiet periods, as represented by the L90 level.
The Leq parameter represents the average noise energy during a measurement period. This parameter is derived by integrating the noise levels measured over the measurement period. Leq is important in the assessment of traffic noise impact as it closely corresponds with human perception of a changing noise environment; such is the character of traffic noise.
Current practice favours the Leq parameter as a means of measuring traffic noise, whereas the L10 parameter has been used in the past and is still incorporated in some codes. For the reasons outlined above, the L90 parameter is not used to assess traffic noise intrusion.
I:\Jobs\2017\20170549\20170549.1\20170512RLA_R0_DA Acoustic Assessment.docx 7
4 TRAFFIC NOISE INTRUSION
Traffic noise criteria has been assessed in accordance with the requirements of Blacktown City Council and the Australian Standard AS2107-2016 “Recommended Design Sound Levels and Reverberation Times for Building Interiors”.
4.1 TRAFFIC NOISE CRITERIA
4.1.1 Blacktown City Council DCP
Blacktown City Council DCP does not have specific acoustic requirements with regards to traffic noise intrusion.
4.1.2 Australian Standards AS2107-2016
The Australian Standard AS2107-2016 “Recommended Design Sound Levels and Reverberation Times for Building Interiors” recommends maximum design sound levels for different areas of occupancy in the residential development while AS 3671 -1989 “Road Traffic Noise Intrusion - Building Siting and Construction” recommends that an appropriate Leq or L10 traffic noise descriptor be used for the occupancy being assessed. Traffic noise criteria for AS2107-2016 is presented in the table below, based on developments near minor roadways.
Table 1 - Australian Standard AS2107-2000 criteria
Space/Activity Type Noise Level dB(A)Leq
Bedrooms 35
Living Areas 40
4.2 TRAFFIC NOISE ASSESSMENT
4.2.1 Unattended noise monitoring
Unattended long term monitoring was conducted by this office, to measure the existing ambient noise environment at the site. The unattended noise monitor was installed approximately 30 meters from the curb, with a restricted view of Seven Hills Road. Monitoring was conducted using an Acoustic Research Laboratories noise monitor set to A-weighted fast response. The monitor was calibrated at the start and end of the monitoring period using a Rion NC-73 calibrator. No significant drift was noted. The noise logging was conducted between the 13th January 2016 and 19th January 2016.
Unattended noise logging data is attached in Appendix 1.
4.2.2 Attended noise measurements
An attended short term measurement of traffic and ambient noise was also undertaken by this office, to supplement the unattended noise monitoring. These measurements were undertaken on the 13th January 2016 at 12.00pm. Measurements were conducted using a Norsonic 140 Sound
I:\Jobs\2017\20170549\20170549.1\20170512RLA_R0_DA Acoustic Assessment.docx 8
Analyser. The analyser was set to fast response and calibrated before and after the measurements using a Norsonic Sound Calibrator type 1251. No significant drift was noted.
Measured ambient noise levels at the monitoring location are listed in the table below:
Table 2 – Measured Existing Traffic Noise Levels
Location
Measured Traffic Noise Level
Daytime (7am-10pm)
dB(A) LAeq (15 hour)
Night time (10pm-7am)
dB(A) LAeq (9 hour)
313 Seven Hills Road, Seven Hills
3m from curb 67 dB(A)Leq(15 hour) 63 dB(A)Leq(9 hour)
4.3 RECOMMENDED CONSTRUCTIONS
Traffic noise intrusion into the proposed development was assessed using the measured external noise levels reported above as a basis.
Calculations were performed taking into account the orientation of windows, the total area of glazing, facade transmission loss and room sound absorption characteristics. In this way the likely interior noise levels can be predicted.
Internal noise levels will primarily be as a result of noise transfer through the windows and doors as these are relatively light building elements that offer less resistance to the transmission of sound. Noise transfer through the masonry elements will not be significant and need not be considered further.
The constructions necessary to achieve the noise levels are detailed below. The predicted noise levels have been based on the expected level and spectral characteristics of the external noise, the area of building elements exposed to traffic noise, the absorption characteristics of the rooms and the noise reduction performance of the building elements.
4.3.1 Glazed Windows and Doors
The following constructions are recommended to comply with the traffic noise objectives stated in Section 4.1. Aluminium framed/sliding glass doors and windows will be satisfactory provided they meet the following criteria listed below.
Thicker glazing may be required for structural, safety or other purposes. Where it is required to use thicker glazing than scheduled, this will also be acoustically acceptable. Glazing to bedrooms or living areas not nominated in the Table are to be minimum 4mm float with acoustic seals.
I:\Jobs\2017\20170549\20170549.1\20170512RLA_R0_DA Acoustic Assessment.docx 9
Table 3 - Recommended Glazing Constructions
Townhouse Room Glazing Seals
T1, T2, T3, T4 Bedrooms 6.38mm laminated Yes
Living rooms 6.38mm laminated Yes
T5, T6, T7, T8, T9, T10 Bedrooms 6.38mm laminated Yes
Living rooms 6mm float Yes
The proposed glazing thickness will satisfy all acoustic requirements of Section 4.1. Thicker glazing may be required for structural, safety or other purposes. Where it is required to use thicker glazing than scheduled, this will also be acoustically acceptable.
In addition to complying with the minimum scheduled glazing thickness, the STC rating of the glazing fitted into openable frames and fixed into the building opening should not be lower than the values listed in Table 4 for all rooms. Where nominated, this will require the use of acoustic seals around the full perimeter of openable frames and the frame will need to be sealed into the building opening using a flexible sealant. Note that all these windows are assumed as aluminium awning windows and mohair seals in windows and doors are not acceptable where acoustic seals are required.
Table 4 - Minimum STC of Glazing
Glazing Assembly Acoustic Seals Minimum STC of Installed
Window
6mm float Yes 29
6.38mm laminated Yes 29
4.3.2 Walls and Roofs
Noise intrusion through the external masonry walls and roofs will be negligible and will not contribute to internal noise levels so no further acoustic treatment is required.
Any penetration in external walls must be acoustically treated and sealed gap free with a flexible sealant.
I:\Jobs\2017\20170549\20170549.1\20170512RLA_R0_DA Acoustic Assessment.docx 10
5 NOISE EMISSION ASSESSMENT
Noise emissions from the subject development should be assessed to ensure that the amenity of nearby land users is not adversely affected.
Potential noise sources which should be assessed include:
Noise generated by future mechanical plant and equipment servicing the proposed development.
Noise from use of the underground car park entry.
5.1 BACKGROUND NOISE MONITORING
Background noise levels at the site have been measured based on the unattended noise logging undertaken by this office as outlined in section 4.2.1.
Measured background noise levels are presented below. Refer to Appendix 1 for unattended noise monitoring data.
Table 5 - Measured Background Noise Levels
Location
Background noise level dB(A)L90(period)
Daytime
(7am – 6pm)
Evening
(6pm – 10pm)
Night (10pm – 7am)
Monitor Location 48 47 37
I:\Jobs\2017\20170549\20170549.1\20170512RLA_R0_DA Acoustic Assessment.docx 11
5.2 ACOUSTIC CRITERIA
5.2.1 Blacktown City Council DCP 2013
Blacktown DCP has the following with reference to noise emissions of residential properties;
Section 6.9.3 – Visual and Acoustic Privacy
“No electrical, mechanical or hydraulic plant or equipment shall generate a noise level greater than 5dB(A) above the ambient L90 sound level at the boundaries of any allotment at any time of day.”
5.2.2 NSW EPA Industrial Noise Policy
The NSW Industrial Noise Policy has two criteria which need to be satisfied namely Intrusiveness and Amenity. These are described below:
Intrusiveness Criteria - This guideline is intended to limit the audibility of noise emissions at residential receivers and requires that noise emissions measured using the Leq descriptor do not exceed the background noise level by more than 5 dB(A). Where applicable, the intrusive noise level should be penalised (increased) to account for any annoying characteristics such as tonality.
Amenity Criteria - This guideline is intended to limit the absolute noise level from all “industrial” noise sources such as mechanical plant to a level that is consistent with the general environment.
The NSW Industrial Noise Policy sets out acceptable noise levels for various localities. Table 2.1 on page 16 of the policy indicates 4 categories to distinguish different residential areas. They are rural, suburban, urban and urban/industrial interface.
Noise levels are to be assessed at the property boundary or nearby dwelling, or at the balcony or façade of an apartment.
5.2.2.1 Intrusiveness Criterion
The guideline is intended to limit the audibility of noise emissions at residential receivers and requires that noise emissions measured using the Leq descriptor do not exceed the background noise level by more than 5dB(A). Where applicable, the intrusive noise level should be penalised (increased) to account for any annoying characteristics such as tonality.
Background noise levels adopted are presented in Section 5.1. Noise emissions from the site should comply with the noise levels presented below when measured at nearby property boundary.
I:\Jobs\2017\20170549\20170549.1\20170512RLA_R0_DA Acoustic Assessment.docx 12
Table 6 – Intrusiveness Noise Emission Goals
Location Period/Time Measured
Background dB(A)L90,15min
Intrusiveness Noise Emission Goal dB(A) Leq(15min)
Nearby Residences
Day (7am-6pm) 48 53
Evening (6pm-10pm) 47 52
Night (10pm-7am) 37 42
5.2.2.2 Amenity Criterion
The guideline is intended to limit the absolute noise level from all noise sources to a level that is consistent with the general environment.
The NSW Industrial noise policy sets out acceptable noise levels for various localities. Table 2.1 on page 16 of the policy indicates 4 categories to distinguish different residential areas. They are rural, suburban, urban and urban/industrial interface. This site is categorised by the residential receivers as suburban.
For the purposes of this condition:
Day is defined as the period from 7am to 6pm Monday to Saturday and 8am to 6pm Sundays and Public Holidays;
Evening is defined as the period from 6pm to 10pm.
Night is defined as the period from 10pm to 7am Monday to Saturday and 10pm to 8am Sunday and public holidays.
Table 7 – Amenity Noise Emission Goals
Location Period/Time
Amenity Noise Emission Goal dB(A) Leq(Period)
Acceptable Maximum
Nearby Residences
Day (7am-6pm) 55 60
Evening(6pm-10pm) 45 50
Night(10pm-7am) 40 45
I:\Jobs\2017\20170549\20170549.1\20170512RLA_R0_DA Acoustic Assessment.docx 13
5.2.3 Protection of the Environment Operations Act Regulation
Protection of the Environmental Operations regulation limits the noise levels associated within the operation of domestic air conditioning criteria during night time periods which is presented below:
Protection of the Environmental Operations (Noise Control) Regulation 2000-Sect 52
52 Air Conditioners
(1) A person must not cause or permit an air conditioner to be used on residential premises in such a manner that it emits noise that can be heard within a habitable room in any other residential premises (regardless of weather any door or window to that room is open):
(a) before 8 am or after 10 pm on any Saturday, Sunday or public holiday, or
(b) before 7 am or after 10 pm on any other day.
5.3 NOISE EMISSION ASSESSMENT
5.3.1 Underground Carpark Entry
This section will present the assessment of the underground car park entry ramp, accessible from Seven Hills Road. The nearest potentially affected receivers are the adjacent residential dwellings located at 315 Seven Hills Road.
Noise emissions from vehicles using the car park will be predicted at the property boundary. They will be predicted based on the following assumptions:
1 movement per carpark space (capacity of 15 cars in the underground car park) during AM and PM peak hours;
The typical sound power level of a light vehicle at 10km/hour speed is 84dB(A) (noise data from similar projects by this office).
Mitigation treatments and management controls detailed in Section 5.4 are implemented.
The predicted noise level at the nearest receivers’ boundary is presented below.
Table 8 - Predicted Noise Level from underground Car Park ramp
Receiver Location Period Predicted Level –
dB(A)Leq(15min) Criteria -
dB(A)Leq(15min) Complies
315 Seven Hills Road Residential receivers
Daytime (7am-6pm) Up to 42
53 Yes
Evening (6pm-10pm) 52 Yes
I:\Jobs\2017\20170549\20170549.1\20170512RLA_R0_DA Acoustic Assessment.docx 14
5.4 RECOMMENDATIONS
5.4.1 Mechanical Plant Items
Mechanical plant items are not typically selected at DA stage.
Detailed review of all external mechanical plant should be undertaken at construction certificate stage (once plant selections and locations are finalised). Acoustic treatments should be determined in order to control plant noise emissions to the levels set out in section 5.2 of this report.
All plant can be satisfactorily attenuated to levels complying with noise emission criteria through appropriate location and (if necessary) standard acoustic treatments such as noise screens, enclosures, in-duct treatments (silencers/lined ducting) or similar.
5.4.2 Management controls
The following engineering controls are required for compliance with the project noise emission goals:
A solid and imperforated 1.8m high fence (9mm FC, 19mm plywood or the like) should be installed between the car park ramp and the property at 315 Seven Hills Road.
I:\Jobs\2017\20170549\20170549.1\20170512RLA_R0_DA Acoustic Assessment.docx 15
6 CONCLUSION
This report presents the assessment of noise impacts associated with the proposed residential development to be located at 313 Seven Hills Road, Seven Hills.
ALC confirm that acoustic treatments have been formulated to ensure that internal noise levels comply with the requirements of Blacktown City Council DCP and Australian and New Zealand AS/NZS 2107:2016.
Mechanical plant servicing the development should be assessed at the construction certificate stage to ensure compliance with the noise emission requirements of Blacktown City Council DCP and NSW EPA Industrial Noise Policy.
We trust this information is satisfactory. Please contact us should you have any further queries.
Yours faithfully,
Remi Larmandieu
I:\Jobs\2017\20170549\20170549.1\20170512RLA_R0_DA Acoustic Assessment.docx 16
APPENDIX 1 - UNATTENDED NOISE MONITORING DATA
I:\Jobs\2017\20170549\20170549.1\20170512RLA_R0_DA Acoustic Assessment.docx 17
I:\Jobs\2017\20170549\20170549.1\20170512RLA_R0_DA Acoustic Assessment.docx 18
I:\Jobs\2017\20170549\20170549.1\20170512RLA_R0_DA Acoustic Assessment.docx 19
I:\Jobs\2017\20170549\20170549.1\20170512RLA_R0_DA Acoustic Assessment.docx 20
I:\Jobs\2017\20170549\20170549.1\20170512RLA_R0_DA Acoustic Assessment.docx 21
I:\Jobs\2017\20170549\20170549.1\20170512RLA_R0_DA Acoustic Assessment.docx 22
I:\Jobs\2017\20170549\20170549.1\20170512RLA_R0_DA Acoustic Assessment.docx 23
7