13205 INSTAL TO IRUCS
Transcript of 13205 INSTAL TO IRUCS
MAKE: STYLE:
MIN.30
WARNING: NEVER EXCEED YOUR VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY
WEIGHT CARRYING:
INSTALLATION TIPS:
INSTALLATION REQUIRES:
VEHICLE PHOTO:
HITCH ILLUSTRATION:
REPRESENTATIVE PHOTO
MAKE SURE YOUR HITCH MATCHES
LEVEL OF DIFFICULTY: EASY
EASY CHALLENGINGMODERATE
1. BEFORE YOU BEGIN INSTALLATION, READ ALL
INSTRUCTIONS THOROUGHLY.
2. TO EASE INSTALLATION, 2 PEOPLE MAY BE
REQUIRED.
3. USING PROPER TOOLS WILL GREATLY IMPROVE
THE QUALITY OF THE INSTALL AND REDUCE THE
TIME REQUIRED.
4. NEED HELP OR HAVE SOME QUESTIONS?
CALL TECHNICAL SUPPORT AT 800.798.0813
Safety glasses should be worn at all times whileinstalling this product.
YEARS: 2015-PRESENT NISSAN MODEL: MURANO SUV
3500
350
TRAILER WEIGHT:
TONGUE WEIGHT:
13205 INSTALLATION INSTRUCTIONS
LBS.
LBS.
WARNING: WE RECOMMEND THE USE OF 18050 STABILIZING STRAPS FOR ALL NON-TRAILER (WHEEL-LESS) LOADS. PLEASE SEE THE CURT CATALOG OR VISIT US ONLINE AT WWW.CURTMFG.COM FOR FURTHER INFORMATION.
MIN.
MIN.45
IF YOU ARE HESITANT TO UNDERTAKE
THIS TASK ON YOUR OWN, CONTACT AN AUTHORIZED
CURT INSTALLER FOR ADDITIONAL ASSISTANCE.
NOVICE INSTALL TIME:
PRO INSTALL TIME:
SCAN FORMORE INFO
PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE ALL FASTENERS ARE TIGHT AND ALL STRUCTURAL COMPONENTS ARE SOUNDCURT Manufacturing LLC. warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective,CURT Manufacturing LLC. may repair or replace the product at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of this productvoids the warranty. CURT Manufacturing LLC.'s liability is limited to repair or replacement of products found to be defective, and specifically excludes liability for incidental or consequential loss or damage.
For more information log onto www.curtmfg.com, & for helpful towing tips log onto www.hitchinfo.com5/12/2020
PART REMOVAL
RATCHET SOCKET
16mm19mm
SOCKET
EXTENSION
10"
TORQUEWRENCH
SAFETYGLASSES
REMOVE TIE DOWN BRACKET (IF PRESENT)
NO DRILLING REQUIRED
(5) WELDNUTS MAY NEED TOBE CLEANED
Parts List
DESCRIPTIONPART NUMBERQTYITEM
HHCS,M12x1.25,30,CL10.9,YZ10-1041951
WASHER,S-CON,1/2,YZ30-0014952
INSTALLATION WALKTHROUGH:
For more information log onto www.curtmfg.com, & for helpful towing tips log onto www.hitchinfo.com
PASSENGER SIDEFRAME RAIL
DRIVER SIDEFRAME RAIL
EXISTING WELDNUTS
EXISTING WELDNUTS
2
1
1. If present, remove the (4) bolts holding the tie down bracket onto the vehicle and return to the owner. 2. Use a M12 - 1.25 tap to clean under coating from existing weldnuts if required.
3. Raise hitch into position between exhaust tip(s) and attach to vehicle using the supplied 12mm bolts and washers. 4. Torque all 12mm fasteners to 86 lb-ft.
Parts List
DESCRIPTIONPART NUMBERQTYITEM
HHCS,M12x1.25,30,CL10.9,YZ10-1041951
WASHER,S-CON,1/2,YZ30-0014952
GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH: LBS. TRAILER WEIGHT & LBS. TONGUE WEIGHT.
***DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY.***
WARNING: ALL NON-TRAILER LOADS APPLIED TO THIS PRODUCT MUST BE SUPPORTED BY 18050 STABILIZING STRAPS.
** FAILURE TO PROPERLY SUPPORT NON-TRAILER LOADS WILL VOID PRODUCT WARRANTY**
HAVING INSTALLATION QUESTIONS? CALL TECHNICAL SUPPORT AT 1-877-287-8634
HITCH WEIGHT: LBS.
INSTALL TIME
PROFESSIONAL: MINUTES
NOVICE (DIY): MINUTES
INSTALL NOTES:
INSTALLATION STEPS
PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE THAT ALL FASTENERS
ARE TIGHT AND THAT ALL STRUCTURAL COMPONENTS ARE SOUND.
CURT Manufacturing LLC., warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser.If the product is found to be defective, CURT Manufacturing LLC., may repair or replace the product, at their option, when the product is returned, prepaid,with proof of purchase. Alteration to, misuse of, or improper installation of this product voids the warranty. CURT Manufacturing LLC.'s liability is limited torepair or replacement of products found to be defective, and specifically excludes liability for incidental or consequential loss or damage.
3500 350
27
30
NISSAN MURANO
5/12/2020
13205
45
Scanfor moreinformation
PASSENGER SIDEFRAME RAIL
DRIVER SIDEFRAME RAIL
TOOLS REQUIRED
RATCHET
16mm SOCKET
19mm SOCKET
10" SOCKET EXTENSIONTORQUE WRENCH
- NO DRILLING REQUIRED- REMOVE TIE DOWN BRACKET (IF PRESENT)
1. If present, remove the (4) bolts holding the tie down bracket onto the vehicle and return to the owner. 2. Use a M12-1.25 tap to clean under coating from frame nuts if required. 3. Raise hitch into position between exhaust tip(s) and attach to vehicle using the supplied 12mm bolts and washers. 4. Torque all 12mm fasteners to 86 lb-ft.
2
1
FRAME WELD NUTS(BOTH SIDES)
TIE DOWN BRACKETATTACHMENT FRAME NUTS