1000 E. Butler Ave. Suite 102 Flagstaff, AZ 86001 Catalog.pdf · KDK Tools 1-800-397-0952 1000 E....
Transcript of 1000 E. Butler Ave. Suite 102 Flagstaff, AZ 86001 Catalog.pdf · KDK Tools 1-800-397-0952 1000 E....
KDK Tools1-800-397-0952
1000 E. Butler Ave.Suite 102
Flagstaff, AZ 86001
KDK Tools1-800-397-0952
CONVERT DOWN TIME TO PRODUCTION TIME
With KDK pre-set QUICK CHANGE TOOLS, you convert costly
set-up time into profitable production time. Short run, repeat
jobs are no longer a set-up time problem. Tools are
changed quickly . . . accurately. The bars are easy to
place on the dove tail from the top. The adjusting
screws for centering tools eliminates
shims underneath the tool bits. All
tools are heat treated and black
oxided to prevent rusting.
2
TOOL LOCKS WITH ATOUCH OF THE FINGER
Series
Recom-mended
LatheSwing
(inches)
CenterHeight
(inches)
LockDown
Bolt Dia.(inches)
Max.ToolBit
(inches)
Approx.Weight(lbs.)
IndividualTool Post
Price
CompleteSet
Price*
0 8 to 12 .750 & Up7/16 ⅜ 2¾ $278 $618
100 12 to 16 1.000 & Up7/16 ½ 5 $300 $716
150 15 to 18 1.250 & Up ⅝ ⅝ 6¼ $337 $854
200 18 to 24 1.500 & Up ¾ ¾(opt. 1”)
10½ $428 $1054
*Set includes Tool Post + 5 bars. (Standard Set pictured on page 3)
NOTE: The dovetail dimensions are the same on 0, 100, 150, and 200 Tool Posts which allowsbars from these series to be interchangeable. However, if using larger series tool holder onsmaller tool post, you must have enough center height.
00 .500 & Up5/16 ¼ 2 $268 $601
TOOL POSTS
COMPLETE SET—KDK TOOL POST PLUS 5 TOOL HOLDER BARS
KDK tool posts usually require a riser plate between the tool post and lathe compound to bring
tool to lathe center height. A blank T-nut and riser plate, up to 1⅛" thick, will be furnished FREE if
you specify lathe center height. See dimension "A" on page 10. Special riser plates thicker than
1⅛" furnished at time and material cost.
NOTE: For a machined T-Nut there is an additional charge. To insure correct size, furnish T-Slot
dimensions (see drawing on page 10).
STANDARD SET
September 2008
KDK Tools1-800-397-0952
EXTENSION TURNINGBAR COMBINATION
KDK TOOL POST
MASTER BAR FORBORING BARS OR OTHERROUND SHANKED TOOLSRISER PLATE
(If requested)
TURNING AND FACINGBAR COMBINATION
PARTINGBAR COMBINATION
THREADING AND FACINGBAR COMBINATION
STANDARD SET
3
T-NUT(Blank)
KDK Tools1-800-397-0952
Bar #Bit Capacity
(inches) Price
02 ⅜ $70
102 ½ $79
152 ⅝ $92
202 ¾ $114
202-1* 1 $145
THREADING & FACING BARCOMBINATION
002 ¼ $63
BARS
Bar #Bit Capacity
(inches) Price
01 ⅜ $72
101 ½ $83
151 ⅝ $96
201 ¾ $123
201-1* 1 $151
TURNING & FACING BARCOMBINATION
001 ¼ $63
Bar #Bit Capacity
(inches) Price
03 ⅜ $73
103 ½ $86
153 ⅝ $96
203 ¾ $113
203-1* 1 $145
EXTENSION TURNING BARCOMBINATION
003 ¼ $63
4*Not included in price of complete set.Must be ordered separately.
KDK Tools1-800-397-0952
BARS
Bar # BladeBit Capacity
(inches) Price
04 P2 3/32 x ½ $89
104 P3 ⅛ x 11/16 $96
154 P5X ⅛ x 7/8 $127
204 P8X ⅛ x 1⅛ $150
PARTING BAR COMBINATION
004 P2 1/8 x ½ $95
Bar #Bar Capacity
(inches) Price
05 ¾" Hole $88
105 1" Hole $96
155 1¼" Hole $133
205 1½" Hole $159
205-1¾* 1¾" Hole $197
205-2* 2" Hole $228
MASTER BAR FOR BORINGBARS
005 3/8 " Hole $95
4-POSITION BARCOMBINATION
Bar #Bit Capacity
(inches) Price
06* ⅜ $87
106* ½ $100
156* ⅝ $111
206* ¾ $128
206-1* 1 $158
006* ¼ $70
5
Also used for turningand facing.
*Not included in price of complete set.Must be ordered separately.
KDK Tools1-800-397-0952
5-B BORING BAR HOLDER(¼ to ½" Boring Bar Capacity)
By turning plate with groove over to flatside you can go down to ¼" diameter
Fits on 0, 100, 150, and 200 series KDKTool Posts.
Price…$104
RIGHT ANGLE TURNING BAR
Minimum tool overhang
Permits larger turning diameter.
Greater rigidity
Able to hold form tools to plunge on face of work
Bar #Bit Capacity
(inches) Price
020 ⅜ $89
1020 ½ $103
1520 ⅝ $115
2020 ¾ $135
2020-1 1 $166
NOTE: A larger series bar may be used on a similarseries tool post, but not the smaller bar on a larger seriespost.
5C COLLET BAR NO. 119
For Lathes having 1" Center Height orMore.
For use on No. 0, 100, 150 and 200KDK Tool Posts
Makes boring easier, allows instantchange to threading, internal grooving,drilling! Quick change from center drillingto tapping. Accuracy as good as yourmachine. Eliminates need for bushings.Assures the simplicity of KDK PresetQuick Change Tools to all 5C collet jobs!
CUTTINGTOOL ANDCOLLET NOTINCLUDED
BARS
6
KDK Part #
119Includes Spanner Wrench
and Lock Ring
Price
$129
119– 1Lock Ring
$18
119-2Spanner Wrench
$19
LockRing
SpannerWrench
KDK Tools1-800-397-0952
SWIVEL BAR FOR VARIED ANGLES
Bar #Bit Capacity
(inches) Price
118 ½ $117
1518 ⅝ $135
218 ¾ $154
7
BARS
DIAMOND KNURLS
FINE MED. COARSE
107
(40pi) (25pi) (16pi)
GKR-240GKL-240
GKR-225GKL-225
GKR-216GKL-216
(33pi) (21pi) (14pi)
KPR-233KPL-233
KPR-221KPL-221
KPR-214KPL-214
NOTE: Knurl Heads come standard withone pair each of Fine, Medium and CoarseDiamond Pattern Knurls. Straight Knurlsavailable upon request.
207
KNURLING BAR
KnurlingBar
with Headand 3 Pr.Knurls
Knurling Barwithout Head
RecommendedLathe Swing
(inches)
107-1 107 8 TO 16
$224 $115
207-1 207
$268 $145
15 TO 24
KNURLING HEAD AND KNURLS
Knurling Headfor Knurling Bar
and KnurlsKnurling Headwithout knurls Knurls (pair)
Knurl Size(inches)
1073K0-3 3K-0 107 KNURL (pair) 5/8 DIA x 5/16
$126 $58 $29
3K1-3 3K-1 207 KNURL (pair) 3/4 DIA x 3/8
$143 $65 $32207
KDK Tools1-800-397-0952
BARS
TOOL HOLDERS FOR TOP NOTCH®*THREADING AND GROOVING INSERTS
Rugged bridge clamp fits into a notch molded into the insert; thisallows precision threading. Features also include full formthreading, 60° vee, a complete series of grooving inserts, acmeand buttress.
Bar # Price Gage InsertClampScrew Price Clamp Price
KDK-NG-3 $170 NG-3 For ref. only,not available through
KDK
$2.50 CM-72 $13
KDK-NG-3 L.H.¹ $194
KDK-NG-4 $214 NG-4 For ref. only,not available through
KDKKDK-NG-4 L.H.¹ $237
Holders are designed to locate insert inclined 3° to provide back clearance down open side.*TOP NOTCH and KENDEX are registered Trademarks of Kennametal Inc. ¹Left Hand
60° Vee (NT, NTC, NTF, NF) These Inserts are designedfor cutting American Standard Unified 60° Vee Threads.They are furnished with a flat, radius, or a full form.
Grooving (NG, NO, NV, NR, NU) A completeline of Top Notch®* Grooving Inserts are avail-able for external and internal work. All NG In-serts are furnished with chamfered corners. Thesame holders and bars can be used for boththreading and grooving.
API Inserts (NDC, NDE, ND) For threading casings, tubing,line pipe and rotary joints. Full form 8 and 10 Rd, V038-40-50 Series.
Acme-Buttress (NA, NAS, NTB-A, NTB-B) 29°
S-412
CM-73¹
CM-72
CM-73¹
$13
$13
$13
S-412
S-412
S-412
$2.50
$2.50
$2.50
8
CARBIDE CUT-OFF TOOL HOLDER SYSTEM
KDKPart #
KDK ToolBodies
Tool Will FitFits BladesNumbers
Blade Size
DimensionFrom BottomOf Holder ToTop Of Insert Price(Inch) Metric
010 0,100,150 19-2 ¾ 19 MM 0.835 $120
1010 100, 150 26-2 THRU 26-6 11/32 26 MM 1.040 $133
1510 150, 200 32-2 THRU 32-6 1¼ 32 MM 1.312 $143
Carbide Cut-Off Tool Holder System will hold the “self grip” typecut-off blades (i.e.: Newcomer, Iscar, Carboloy, Kennametal, etc.)see the chart above for information on which holder will fit yourblade size.
DESIGNED TO GIVE YOU GREATER CHATTER-FREERIGIDITY UNDER HEAVY DUTY REQUIREMENTS
Cut-off bladenot included
Right HandShown
KDK Tools1-800-397-0952
SPARE PARTS
9
(OLD STYLE)
No. 0Tool Post
No. 100Tool Post
No. 150Tool Post
No. 200 ToolPost
Part Name Part No. Part No. Part No. Part No.
Shoe (new style)For use on tool posts
purchased prior to 2001specify “O” after part no.
A-0-1 A-100-1 A-150-1 A-200-1
$55 $61 $61 $64
Cam A-0-2 A-100-2 A-100-2 A-100-2
$64 $73 $73 $73
Handle, Assy. Right Hand A-0-4 A-100-4 A-150-4 A-150-4
$37 $43 $47 $47
Knob A-0-5 A-0-5 A-0-5 A-0-5
$4.75 $4.75 $4.75 $4.75
Nylok Button-Head Screw A-0-6 A-0-6 A-0-6 A-0-6
$2.50 $2.50 $2.50 $2.50
Half Dog Point Screw A-0-7 A-0-7 A-0-7 A-0-7
$1.50 $1.50 $1.50 $1.50
Dowel Pin A-0-8 A-0-8 A-150-8 A-150-8
$1.50 $1.50 $1.50 $1.50
Lock Down Bolt A-0-9 A-100-9 A-150-9 A-200-9
$4.75 $5.75 $7.75 $12.50
Spring Washer A-0-11 A-100-11 A-100-11 A-100-11
$2.50 $2.50 $2.50 $2.50
04-1 104-1 154-1 204-1
$28 $30 $32 $38
Clamp Block with Screwsfor Parting Bar
No. 00Tool Post
Part No.
A-00-1
$41
A-00-2
$63
A-00-4
$28
A-00-5
$3.25
A-00-6
$1.75
A-00-7
$1.00
A-00-8
$1.00
A-00-9
$3.50
A-00-11
$1.25
004-1
$25
KDK Tools1-800-397-0952
KDK TOOL POST DIMENSIONS
TOOL POST NUMBER
0 100 150 200
F 3.00" 3.50" 4.37" 5.00"
G 2.25" 2.50" 2.50" 2.87"
H 1.62" 2.25" 2.25" 3.00"
I .312" .312" .312" .312"
J 1.750" 1.750" 1.750" 1.750"
K 1.875" 2.125" 2.125" 2.125"
L .687" .687" .687" .687"
M 7/16" 7/16" 5/8" 3/4"
N 30° 30° 30° 30°
O .312" .331" .331" .331"
P 1/4" 1/4" 5/16" 5/16"
Q .687" .875" 2.312" 2.562"
R 1.343" 1.375" 1.250" 1.437"
00
2.00”
1.62”
1.12”
.187”
1.00”
1.30”
.375”
5/16”
45°
.171”
1/8”
1.00”
.937”
10
ORDERINGINFORMATION
DIMENSIONS NEEDED TO FIT KDK TOOL POSTS TO YOURLATHE
KDK tool posts usually require a riser plate between the tool post and lathe
compound to bring tool to lathe center height. A riser plate, up to 1⅛" thick,
will be furnished FREE if you specity make and model of lathe or furnish
lathe center height. See dimension ‘A’ below. Special riser plates thicker
than 1⅛" furnished at time and material.
NOTE: T-Nuts are not standard for all lathes. To insure correct size, furnish
T-Slot dimensions A, B, C, D, and E (see drawing below), and specify make
and model of lathe.
T-SLOT DIMENSIONS
1-800-397-0952
KDK Tools1-800-397-0952
11
SALES POLICY:SALES TAX:KDK Tools is required to charge applicable State and local sales tax on every item for which a sales tax exemption certificate hasnot been provided. When ordering, please indicate clearly which items are or are not taxable.
RETURNED GOODS:Our authorization to return materials is required. To expedite the issuance of credit, please furnish our invoice number and date ofinvoice. Materials returned due to our error will be promptly credited in full provided they are returned within 30 days and arereceived in original saleable condition. All other returns are subject to charges for inspection or restocking. We cannot acceptmaterials which have been in any way damaged or altered.
SPECIAL GOODS:Orders for nonstandard material/design, special order, or altered at your request cannot be cancelled or returned unlessproduction has not yet begun. If cancelled, customer will be charged for any work done before production is stopped.
CANCELLATIONS:Our permission in writing is required to cancel orders placed with us and are subject to a cancellation charge. Such permissioncan only be granted on the merit of each case.
WARRANTY POLICY:LIMITATION OF REMEDY:Any liability for consequential and incidental damages is expressly disclaimed. The liability of KDK Tools in all events is limited to,and shall not exceed, the purchase price paid.
DELAYS BEYOND SELLER’S CONTROL:Seller shall not be responsible for delays in performance caused by delays in manufacturing, transportation or due to strikes, fires,floods, storms, war, insurrections, riots, any governmental regulation, order, act or instruction, or any circumstances beyond theSeller’s reasonable control. Buyer’s acceptance of goods and/or services shall constitute a waiver of any claims for damages dueto delay. Under no circumstances shall the Seller be liable for any loss or use by Buyer or for any indirect or consequentialdamages arising from such delays.
ERRORS:Clerical and Statistical errors are subject to correction.
LIMITED WARRANTY TO ORIGINAL PURCHASER
KDK Tools warrants all KDK products against defects in material and workmanship to the original purchaser for a period of oneyear from the date the product is delivered to the original purchaser. KDK Tools will repair or replace, at its option, at no charge,any KDK product found to be defective during the warranty period. Such repair or replacements shall not include the costs ofdisassembly, removal, or reinstallation or any other services involved, which costs are the responsibility of the purchaser. Thewarranty repairs must be performed at KDK.
OBLIGATION OF THE ORIGINAL PURCHASER
1. The original dated contract of sale for the KDK product must be retained as proof of purchase and must be presented to theKDK service center.
2. Transportation of the KDK product to and from the service center is the responsibility of the original purchaser who mustprepay transportation and insurance costs.
EXCLUSIONS OF THE WARRANTY
This warranty covers all KDK products under normal use and service and does not cover accident, misuse, fire, flood, other acts ofGod, negligence, alteration, abuse, improper or unauthorized repair and customer adjustments.This warranty is not transferable, is limited to the original purchaser, and is valid only on products purchased, installed and used inthe United States of America.
CONDITIONS:GENERAL:Prices & Discounts are subject to change without notice.
TERMS:2% discount if paid within 10 days of invoice date - NET 30 days. Terms valid on approved credit only.
KDK Tools Reserves the right to delete products, make product improvements, changes, or modifications to all productsmanufactured or sold without incurring any liabilities to incorporate these changes in any part or component - past, present, orfuture.
Every effort has been made to insure that the specifications listed in this catalog are correct. However, KDK Tools does notguarantee the accuracy or correctness of such information listed in this catalog.
The design guidelines & prints in this catalog serve as a reference only.
WARRANTY
KDK Tools1-800-397-0952
Toll Free: 1-800-397-0952Phone: (928) 774-8715
Fax: (800) 779-8188
BULLETIN 6100