Leader: Liu Du Kai Ying Member: Nicholas Lim Dexter Kuah Dexter Kuah.
1 Amos Dexter, on behalf of Roger M. Jones, Carl Beard, Ian Shinton Wake-fields in the Main...
-
date post
20-Jan-2016 -
Category
Documents
-
view
216 -
download
2
Transcript of 1 Amos Dexter, on behalf of Roger M. Jones, Carl Beard, Ian Shinton Wake-fields in the Main...
1Amos Dexter, on behalf of Roger M. Jones, Carl Beard, Ian Shinton
Wake-fields in the Main Superconducting L-Band
Linacs of the ILC
Amos DexterThe University of Lancaster; Cockcroft Institute, Daresbury, UK
2Amos Dexter, on behalf of Roger M. Jones, Carl Beard, Ian Shinton
Overview of WP 3.1• Physics issues of mode coupling and means to ameliorate beam
instabilities –Scientific excellence/fundamental physics
• Knowledge transfer lays in the re-designs that will be required to reduce the impact of the damaging wakefields. UK industry may gain some inroads on the fabrication of 153,000 cells.
• Clear potential for the UK to be a lead player in the main linacs of the international linear collider.
• Beam dynamics are an outstanding issues raised by the ILC R&D board.
• Past experience (SLAC) has shown that beam instabilities are a serious issue that can readily make the collider unusable. We must anticipate these instabilities using simulations taking into account realistic statistics on likely fabrication errors
ILC main cell designs currently under R&D
Potentially trapped HOM (Higher Order Mode)
3Amos Dexter, on behalf of Roger M. Jones, Carl Beard, Ian Shinton
Overview of WP 3.2• A) Beam-based experiments will take place on the ERLP at Daresbury and the
FLASH/TTF2 (5 x 8-cavity modules) facility at DESY.• Aim at understanding 1) beam-based and 2) cavity alignment based on radiation from
HOM couplers.
• Should it prove a feasible technique all (or significant fraction) 17,000 cavities will be instrumented with these diagnostic tools. Immense value to the ILC community.
• B) Bench-top passive experiments: thin wire stretched through cavity takes place of beam.
• Will allow rapid characterisation of cavities. More economically viable.• Several fundamental physics issues regarding trapped modes have to be understood. -
Scientific excellence/fundamental physics.
FLASH user facility at DESY
Proposed wire measurement of higher order modes in L-band superconducting cavity
Earlier wire measurement on X-band room temperature cavity (R.M. Jones et al, SLAC, 2005)
4Amos Dexter, on behalf of Roger M. Jones, Carl Beard, Ian Shinton
ILC GDE Linac Member Comments
…I understand that your new study programs are very important for realization of the ILC. Especially important is to understandwhat will happen in mass production stage and to control the production suited for obtaining the required beam properties.
To this end, we at KEK will make actual cavities and you analyse them from both theoretical approach and experimental one.The latter should include the beam study at DESY or even at KEK and the studies using low power model by applying various approach such as a wire method which you proposed.
I am sure these new studies plays a very important role in L-band ILC.
Hoping your proposed activities be realilzed soon,
-Toshiyasu Higo, ILC R& D Board, KEK, Japan.
..The program you propose of both computational and experimental study of cavity wakefields is imperative for the ILC. Currently, there is little understanding of what causes the frequency variation of the cavity dipole modes and their polarization splitting. Creating a model that matches the cavity data at DESY is very important as this model can then be used to look for trapped modes in higher order dipole bands (4-8 GHz). This is one area that has not been fully explored at DESY, and yet poses a large risk for multi-bunch operation at both the XFEL and ILC. Approaching this both experimentally and theoretically, which I believe you are well suited to do, offers the best chance to resolve this issue, and I hope that this effort goes forward. -Chris AdolphsenSLAC / ILC Linac Area Leader
…Your program sounds very important. Both Cornell and KEK are developingnew geometries for the Alternate Design Configuration. Wakefields and HOMs for these new geometries need to be carefully studied before theChange Control Board can consider accepting a change from the BaselineDesign. Both monopole and dipole modes are important. ...
Therefore I would encourage you strongly to pursue such studies
-Hasan Pasamdee, ILC R&D Board, Cornell Univ., USA.
5Amos Dexter, on behalf of Roger M. Jones, Carl Beard, Ian Shinton
A TESLA module
I. Shinton CI All-hands 30/03/07
6Amos Dexter, on behalf of Roger M. Jones, Carl Beard, Ian Shinton
Reasons for modelling entire ILC structure
Alignment and machining errors in real modules
Every TESLA cell will have some effect on its neighbours
Trapped modes in various parts of the structure
I. Shinton CI All-hands 30/03/07
7Amos Dexter, on behalf of Roger M. Jones, Carl Beard, Ian Shinton
Alignment errors and trapped modes...
Measurements Made to Date:
A trapped mode is a resonant
mode (HOM) which is non-
propagating and is strongly
localised in part of the
accelerating structure.
Alignment and machining errors
are simply a departure away
from the idealised geometry,
cause by incorrect alignment or
manufacture of a series of cells.
8Amos Dexter, on behalf of Roger M. Jones, Carl Beard, Ian Shinton
Computational simulations to date
Model the entire regionUse Parallel super
computers Model an idealised cavity
9Amos Dexter, on behalf of Roger M. Jones, Carl Beard, Ian Shinton
Cascading finite element schemes:
Simulation of large structures
10Amos Dexter, on behalf of Roger M. Jones, Carl Beard, Ian Shinton
Basic cascading techniques
G.L.James, IEEE Transactions on Magnetics Vol 30, no 2, pg 1059-1066
A.K.Hamid, Int. J. Electronics Vol 80, no 3, pg 471-477
All cascading techniques originate from the generalized scattering matrix technique: R.Mitra and S.W.Lee 'Analytical techniques in the theory of guided waves', Macmillan Comp, New York (1971)
Step junction cascading
Double step junction cascading
R.M.Jones, N. Baboi, S.G. Tantawi, Proceedings of the 2003 Particle accelerator conference, pg 1270-1272
References
11Amos Dexter, on behalf of Roger M. Jones, Carl Beard, Ian Shinton
HFSS cascading simulations
12Amos Dexter, on behalf of Roger M. Jones, Carl Beard, Ian Shinton
Build S matrix library
A generalized scattering matrix technique
Derive a Globalized S matrix for each Tesla cell with respect to each module
in the linac
Derive unit cell S matricesincluding variations in
geometry/ machining and alignment errors
13Amos Dexter, on behalf of Roger M. Jones, Carl Beard, Ian Shinton
Reasons for using HFSS HFSS uses an FEM rather than FD
FEM is more accurate than FD. If the amount of individual error is not minimised in the unit cell used in the cascading technique, then cascaded errors will grow...
FEM has adaptive meshing FEM convergence can readily be proved
HFSS uses edge elements – so the prospect of spurious solutions is eliminated.
14Amos Dexter, on behalf of Roger M. Jones, Carl Beard, Ian Shinton
Things to keep in mind when cascading....
Enough modes must be modelled in the chosen unit cell
A very accurate mesh should be used When applying a frequency sweep, to obtain
or gauge the resonant frequencies and shifts in these frequencies, both a fine enough choice in sweep step and mesh used in the sweep must be implemented; otherwise degeneracy may result....
Calibration lines or a very refined mesh must be used to prevent degeneracy.
15Amos Dexter, on behalf of Roger M. Jones, Carl Beard, Ian Shinton
Overall aims of the simulation effort
1.Provide a realistic simulation including machining and alignment errors, to which the effect of the passage of the beam and wake field effects can be determined
2.Be able to compare the realistic simulation to experiments
3.Provide a possible means by which the entire ILC structure can be accurately modelled.
4.Determine the shifts in the HOM in a real structure
5.Provide a means for evaluating determining positions of trapped modes, allowing couplers/cells in those regions to be tuned to avoid these modes.
16Amos Dexter, on behalf of Roger M. Jones, Carl Beard, Ian Shinton