11

Coolants

Tom Birch

Jim Halderman

2

Introductions: Tom Birch

• Retired instructor from Yuba College, Marysville, CA.

• Author of many automotive textbooks

• Former officer in CAT and NACAT Board Member

3

Jim Halderman

Former flat-rate technician and instructor and a business owner. Author of many automotive books and lives in Dayton, Ohio.http://jameshalderman.com

4

Topics to be Discussed

Engine coolants- Purpose and function Water (1/2 of the coolant)Coolant TypesCooling system testingCooling system service

55

What is Coolant?

Coolant is a mixture of: 1. Water (50%)

2. Anti-Freeze (ethylene glycol-about 93%)

3. Corrosion inhibitors (additives)

Water: 50%

Ethylene Glycol: 47%

Additives: About 3%

Coolant

Need to know

66

Water

Water is the principal ingredient and:

1. Is inexpensive 2. Is a very efficient heat exchange fluid 3. Has excellent thermal conductivity 4. Has a good specific heat 5. Freezes at 32°F (0°C) 6. Boils at 212°F (100°C)The water used in coolant must be clean &

pure.

Need to know

77

Good Water

The American Society for Testing and Materials (ASTM) standards for water quality include:

Chloride <40 ppm Sulfate <100

ppm Calcium <100 ppm Magnesium <100 ppm Total Hardness <170 ppm pH Range: 5.5—9.0 Iron <1 ppm

Nice to know

88

Freeze and Boil

Pure Water 50/50 Anti-Freeze/Water

70/30 Anti-Freeze/Water

Freezing Point

0° C (32° F) -37° C (-35° F) -55° C (-67° F)

Boiling Point 100° C (212° F) 106° C (223° F) 113° C (235° F)

Need to know

9

Ethylene Glycol (EG)

Ethylene glycol is the base antifreeze used in every OEM factory fill. The additive package will vary.

Need to know

10

Propylene Glycol (PG)

• Only sold to the aftermarket

• Not recommended for use by vehicle manufacturers

• More expensive than EG, Increased cost is $/gallon

• Still toxic but is not as sweet as EG

Need to know

11

Embittered Coolant

Embittered = tastes awful

Embittering agent is required (denatonium benzoate, 30 ppm) Required in California and Oregon since 2004 but not included on the label.Need to know

Bittered States

At this time, 7/20/10, 12 states require antifreeze with a bittering agent: dentonium benzoate. They are:

4 states: Illinois, Massachusetts, New Hampshire, and Ohio are working on a similar rule.

13

OAT=DEX-COOL is one brand

Nice to know

14

HOAT=Red; Pink; Yellow or Blue

Nice to know

15

Replacement Antifreeze

The best choice is to follow the vehicle manufacturer’s recommendations.

OR, you can follow the recommendations of reliable antifreeze manufacturers (next slide).

Need to know

16

Coolant Summary • Ethylene glycol - Most ethylene glycol coolant is any color and contains about 93% ethylene glycol

plus water and additives.

• Propylene glycol - less harmful to pets and animals because it is not sweet tasting, although it is still harmful if swallowed.

• Organic acid technology (OAT) antifreeze coolant – This type is ethylene glycol based but it does not contain silicates or phosphates. It is usually orange. DEXCOOL is an OAT coolant.

• • Hybrid organic acid technology (HOAT) – This orange, green, red, blue or yellow coolant is an

ethylene glycol based coolant similar to the OAT- type antifreeze as it uses additives (a low amount of silicate)

• VW/Audi pink - Most of these coolants are HOAT (ethylene glycol-based with some silicate and contain an organic acid) and are phosphate free.

• Asian red – This coolant is ethylene glycol-based and is silicate-free, yet contains phosphate.

• Mercedes and Ford yellow – This conventional ethylene glycol coolant has low amounts of silicate and no phosphates.

• Mercedes Lifetime – Very expensive, can be drained, filtered and reused.• Korean or European blue – This conventional ethylene glycol coolant has low amounts of silicate

and no phosphates.

Nice to know

17

pH Tests

pH can be measure using test strips or a meter.

Fairly accurate and costs pennies/test.

Need to know

18

Metal Corrosion

This iron tube has been ruined by rust.

Need to know

19

Diesel Wet Sleeve Cavitation

The sleeve can vibrate during the combustion stroke producing the pressure drop, bubbles, and metal erosion. Heavy duty coolants contain supplemental coolant additives (SCA) to help prevent this.

Need to know

20

Bi-Metal Corrosion

Ions move from more active metals to less active metal through the coolant which acts like the electrolyteNice to know

21

Radiator Voltage

Connect the negative voltmeter lead to a good ground (this radiator has a plastic filler neck), and immerse the positive lead into the coolant. A reading of 0.300 V or greater indicates corrosion is probably occurring.

Need to know

22

Refractometer Image

The image will show the amount of freeze protection and is read at the scale at the bottom edge of the shadow. This unit can check EG and PG antifreeze freeze protection and battery specific gravity.

Shadow

Read Here

Need to know

23

Universal Coolant

• Arctic Blend

• Recycool

•Prestone Prime

coolants that have been formulated to be used in any vehicle

Nice to know

2424

Additives

The major additives:

1. Reduce corrosion

2. Buffer (control) pH

3. Add color (dye)

Need to know

25Need to

know 25

IAT

Inorganic Additive Technology (IAT) is the traditional green coolant used in most older vehicles. This solution offers fast-acting corrosion protection, but the additives are quickly consumed, exposing the cooling system to possible corrosion problems if not changed regularly.

2626

IAT (Usually Green in Color)

Inorganic Additive Technology (IAT) antifreeze can contain:

• Silicates (possible abrasive dropouts)

• Phosphates• Borates

Need to know

IAT is considered obsolete and can cause early failure of ceramic-phenolic seals used in newer water pumps.

2727

OAT (Usually Orange)

The downside of OAT is it is not compatible with other types of coolant (IAT and HOAT). In fact, Ford, Chrysler and others say to not use this type of coolant in their newer models.

Organic Acid Technology (OAT) is the formula found in DEX-COOL®, and is usually the antifreeze/coolant of choice for GM, VW, and many Japanese/Asian vehicles. This formula is engineered to offer long-life corrosion protection.

Need to know

28

OAT-continued

NAPS=nitrates, amines, phosphate and silicate free

Nice to know

29

OAT=DEX-COOL is one brand

Nice to know

30

DEX-COOL Concerns

• Root cause= air entering system

• Check cap replace cap

• Air causes ‘Brown Gunk’

• Rust then causes blockages

Need to know

31

Rust in Engine

• DEX-COOL + Air= rust orDEX-COOL + core sand = Brown gunk

Need to know

32

GM DEX-COOL Problems

Class action suit; GM may have to pay for intake gaskets on V-6s (V-8s still being determined)

Brown Gunk on radiator cap

Need to know

33

DEX-COOL’s Unique Formulation

• DEX-COOL uses Ethylhexanoic Acid (2-EH) as a corrosive inhibitor

• 2-EH is prone to damage plastics like Nylon 6.6 used in intake manifold gaskets and radiators

• G30 OAT and Peak Global OAT do NOT use 2-EH

Nice to know

3434

HOAT (Many colors)

Hybrid Organic Acid Technology (HOAT) is found in newer Ford, Chrysler and Mercedes vehicles. Said to use the very best aspects of both IAT and OAT, HOAT is a very protective, long-life coolant.

Need to know

35

HOAT=Red; Pink; Yellow or Blue

Nice to know

POAT Coolant

• Phosphated Organic Acid Technology (POAT)

• Dark Green in color• Used in Mazda-based

Fords (2008+)• same as Mazda FL-

22 • $34.95 per gallon

Ford Motor Company & E-OAT

37

The E = European, low silicate and phosphate free

•Ford of Europe has validated Dex-Cool and uses it with no problems.

•Ford of U.S. has reengineered all of their new engines (No- Cavitation water pumps and no-silicone rubber or Nylon 66) to work with this formula.

Ford/Mercury Coolant

38

The 1999—2001 Cougar used a OAT Dex-Cool clone, but had issues with water pump cavitation.

Pre 1999 99—01 2002 2003 2004

Dex-Cool & OAT that meets GM Spec.

39

Prestone markets an OAT antifreeze (Extended Life)

“compatible with ANY antifreeze/ coolant”) that meets the GM Dex-Cool spec.

it is less expensive than Dex-Cool-labeled products because of no-royalty cost.

40

Passivation

• Passivation= is a chemical reaction the takes place between coolant additives and the metal that it protects

• Takes a few days or few weeks • It creates barrier between the metal and corrosion•  Each chemical package does its own passivation • if you change chemical packages, passivation has to

start over  • It boils down to: DO NOT CHANGE PACKAGES.

Nice to know

41

“G” Designations

• G= Glysantin –trade name of BASF. Valvoline (Zerex) in the US.

• G30, G33, G34= non-silicate and phosphate free (DEX-COOL replacement)

• G05 = Phosphate free-low silicates (Asian formula and Chrysler HOAT)

Nice to know

42

“G” Designations-continued

• G11=Blue VW used before 1997

• G12=Pink/Red VW 1997+

• G12=Purple VW 2003+

• HOAT formulation; phosphate free

?

43

“G” Designations-continued

• G48=Low Silicate and Phosphate free

• Blue Color

• NAP =nitrates, amines, phosphate free

• BMW

?

44

Replacement Antifreeze

The best choice is to follow the vehicle manufacturer’s recommendations.

OR, you can follow the recommendations of reliable antifreeze manufacturers (next slide).

Need to know

4545

Color

The color helps us identify a coolant leak. It also helps us identify the additive package.

Should not be used as an indicator what to use-some Chrysler vehicles used HOAT coolant that was green

Need to know

46

47

Coolant Summary • Ethylene glycol - Most ethylene glycol coolant is any color and contains about 93% ethylene glycol

plus water and additives.

• Propylene glycol - less harmful to pets and animals because it is not sweet tasting, although it is still harmful if swallowed.

• Organic acid technology (OAT) antifreeze coolant – This type is ethylene glycol based but it does not contain silicates or phosphates. It is usually orange. DEXCOOL is an OAT coolant.

• • Hybrid organic acid technology (HOAT) – This orange, green, red, blue or yellow coolant is an

ethylene glycol based coolant similar to the OAT- type antifreeze as it uses additives (a low amount of silicate)

• VW/Audi pink - Most of these coolants are HOAT (ethylene glycol-based with some silicate and contain an organic acid) and are phosphate free.

• Asian red – This coolant is ethylene glycol-based and is silicate-free, yet contains phosphate.

• Mercedes and Ford yellow – This conventional ethylene glycol coolant has low amounts of silicate and no phosphates.

• Mercedes Lifetime – Very expensive, can be drained, filtered and reused.• Korean or European blue – This conventional ethylene glycol coolant has low amounts of silicate

and no phosphates.

Nice to know

48

Depletion Rate of Additives

Need to know

4949

pH

Substance pH

Hydrochloric acid -1.0

Battery acid 0.5

Lemon juice 2.4

Cola 2.5

Vinegar 2.9

Orange or Apple juice 3.5

Acid Rain <5.0

Tea or healthy skin 5.5

Milk 6.5

Pure water 7.0

Healthy human saliva 6.5 – 7.4

Blood 7.34 – 7.45

Sea water 7.7 – 8.3

Hand soap 9.0 – 10.0

Household ammonia 11.5

Bleach 12.5

Household lye 13.5

Caustic Soda 13.9

pH is a measure of acidity or alkalinity of a solution. Less than 7 is considered acidic. Greater than 7 is considered alkaline.

Alkaline

Acid

Nice to know

5050

pH Effects

Fresh antifreeze pH= 9 and 11

Used coolant pH= 7.5 and 10

It can also increase electrolysis

( the dissimilar metals in contact with an electrolyte can produce a simple battery)

Need to know

51

pH of various coolants

• IAT= 9.0-10.5 new

• OAT= 7.5-8.5 new (G30 and G34 designation)

• HOAT= 7.5-8.5 new (G05,G48,G11 or G12 designation)

Need to know

52

Desired pH

Need to know

53

pH Tests

pH can be measure using test strips or a meter.

Fairly accurate and costs pennies/test.

Need to know

54

pH Meter

This Milwaukee is probably more accurate and cost $30.00.

Need to know

5555

Corrosion

Corrosion is the “decomposition of metal”

(called rust or aluminum oxide, the whitish material that forms on aluminum components)

Oxide formation:

1. eats away at the parent material from the outside

2. forms an insulating barrier for heat transfer

Need to know

56

Metal Corrosion

This iron tube has been ruined by rust.

Need to know

5757

Corrosion

aluminum oxide, often found on coolant outlet/stat cover

Need to know

58

Corroded Water Pump

One of the reasons for the removal of silicates from coolant

Need to know

59

Corroded pump can cause:

• reduced coolant flowand an overheating

condition

Need to know

6060

Cavitation

Cavitation is the sudden formation and collapse of low-pressure bubbles. With gasoline engines, the pressure drop can occur at the inlet of the water pump. These bubbles produce a pitting of the solid metal .

Cavitation

Need to know

61

Cavitation Damage

The very low pressure can produce gas bubbles that implode next to a metal surface. The implosion blasts particles from the surface.

Need to know

62

Diesel Wet Sleeve Cavitation

The sleeve can vibrate during the combustion stroke producing the pressure drop, bubbles, and metal erosion. Heavy duty coolants contain supplemental coolant additives (SCA) to help prevent this.

Need to know

63

Galvanic action

• Galvanic activity does not require an outside source of voltage

• The higher the conductivity of the coolant, the greater the amount of corrosion

Need to know

64

Metals

Nice to know

65

Bi-Metal Corrosion

Ions move from more active metals to less active metal through the coolant which acts like the electrolyteNice to know

6666

Electrolysis

Electrolysis requires the use of an outside voltage source.

•When electrical ions move from metal to the coolant, they can take metal atoms with them

• This metal transfer can eat holes in a heater core or radiator.

•Electrolysis holes will usually start from the inside and have a dark coloration. Need to know

67

Testing Coolant with a Voltmeter

• This test gives variable and questionable results depending on many factors

• Galvanic=less than 200 mV

• Electrolysis= (engine running and accessories switched on and off)=less than 300 mV. This check can locate faulty ground connections

Need to know

68

Radiator Voltage

Connect the negative voltmeter lead to a good ground (this radiator has a plastic filler neck), and immerse the positive lead into the coolant. A reading of 0.300 V or greater indicates corrosion is probably occurring.

Need to know

69

Coolant Condition

This “green” antifreeze has a clean, bright appearance. The other types will have a different color but should also appear clean and bright.

A muddy brown or rust-reddish color indicates that corrosion is occurring.

Need to know

70

Freeze Protection, Refractometer

A few drops of coolant are placed under the sample window. The technician then holds the unit up to light and looks through the eye piece (right end).

Sample Window

Eye Piece

Need to know

71

Refractometer Image

The image will show the amount of freeze protection and is read at the scale at the bottom edge of the shadow. This unit can check EG and PG antifreeze freeze protection and battery specific gravity.

Shadow

Read Here

Need to know

7272

Freeze Protection, Test Strips

Test strips will change color when they are dipped into the coolant, and the color change is compared to the container.

Test strips are fairly accurate, easy to use, and inexpensive.

Need to know

73

Coolant Corrosion Protection

The new test strip color is compared to the color pads on the container to determine the amount of freeze protection and corrosion protection.

Need to know

74

Coolant Replacement

1. 15 to 20% remains in the system after it has been drained

2. Fill system with antifreeze first and top off with water

3. Be sure to use the specified coolant

(GM warns not to reuse coolant drained from the system)

(Mercedes has a lifetime coolant, drain, filter, & reuse)

Need to know

75

Coolant Replacement-#2

• Check the pressure cap and radiator for faults• Check all hoses and always use coolant hose

Need to know

76

Universal Coolant • Universal Gold =HOAT, extended life, low-

silicate, phosphate-free antifreeze/coolant.

• This product meets Ford WSS M97B51-A1 and Chrysler MS 9769 and other "global antifreeze" type specifications, as well as ASTM D3306, D4985 and D6210/11

Nice to know

77

Universal Coolant

• Arctic Blend

• Recycool

•Prestone Prime

coolants that have been formulated to be used in any vehicle

Nice to know

78

Coolant Recovery and Storage

Some shops recycle used antifreeze

Should be stored until picked up for recycling

Notice double containers to help avoid spills

Need to know

79

Flushing a Dirty System

1. Drain system 2. Fill system with clean water & chemical 3. Run system to operating temp. (Heater on) 4. Drain system & fill with clean water 5. Repeat until drain water runs clear Any remaining flush agent will upset pH. 6. Fill system with 50/50 antifreeze/water mix 7. Run system to operating temp. (Heater on) 8. Adjust coolant level

Need to know

Caution: If flushing a really dirty system, be prepared to repair some leaks.

80

Flushing

Some communities permit draining into sewer. EG and PG will biodegrade. There is a problem however if coolant is spilled on open ground.

Need to know

81

Be sure to clean the overflow/surge tank

It should empty if you start draining with the cap in place.

Need to know

82

Mix Coolant 50/50 or use premix

?

83

Coolant Exchange Machine

Most shops use machines like this.

Coolant drains have become fragile and hard to find.

Need to know

TECH TIP

• Check the freezing Point after service

• Should be -34 degrees F (proper 50/50 mix)

• If higher (i.e. -20 F) this means that there is too much water.

• If lower (i.e. -40 F) this means that there is too much antifreeze

85

Always check or replace the radiator pressure cap

The cap can be located on

1. the radiator

2. The coolant recovery reservoir

3. The upper radiator hose

Note the pressure.

Need to know

86

Cap has two seals

What will happen if the upper seal fails? What will happen if the lower seal fails?

Upper Seal

Filler Neck

Lower Seal

To CRR

Need to know

87

Never open when hot!

What can happen if the cap is removed from a hot system?

Need to know

1 psi will increase the coolant boiling point 2.7oF. A 15 lb. Cap will increase the BP 40.5oF.

88

Proper Fill

All of the air must be removed from the cooling system by one of these methods:

• Bleeder screw: lets air escape• Air Lift: evacuates system before fill• Spill-Free Funnel: Lisle #22150• Fluid Exchange: requires special equipment

Need to know

89

Bleeder Valves

• Use a clear hose attached to the bleeder valve and the other end in a “suitable” container

• Prevents coolant from getting on the engine and gives the technician a visual clue as to color of coolant

Need to know

90

Leak Detection

A good system holds pressure

Tracer dye and some antifreezes glow under UV light

Need to know

91

What should Technician's do?

• Check service information for the designated coolant and replacement interval

• Check the coolant appearance and level at every service

• Check the pressure cap appearance at every service• Check the appearance and pH for signs that the

coolant should be replaced before the regular service interval

• Check Freeze Point, pH, and Galvanic/Electrolysis

Need to know

92

Typical Questions/Answers

1. Are all green antifreezes the same?A. No-Chrysler used HOAT coolant that was green like IAT coolant

2. Can DEX-COOL be replaced with conventional green coolant?A. Yes, but then the coolant has be replaced every 24 months or 24,000 miles

93

Questions/Answers

3. Can coolants be mixed?A. No

4. Is DEX-COOL propylene glycol ?A. No. DEX-COOL and all other coolants are ethylene glycol except one labeled propylene glycol and is never used from the factory

94

Summary

• Not all coolants are the same• Not all tap water is OK to use• Premixed coolant usually produces good

results• Check the coolant freezing/boiling point• Check the coolant pH • Always check or replace the pressure cap,

especially on DEX-COOL vehicles

95

Resource materials

96

Contact Information

Tom Birchhttp://tombirch.com

Jim Halderman- jim@jameshalderman.com