DE5281 1

0$(6752 0$(6752

6 and 10 Zone Alarm Control Panel Installation Instructions

MAESTRO-600 / MAESTRO-1000 CONTROL PANEL

2 DE5281

Table Of Contents

1. INTRODUCTION................................................ 31.1 About This Manual ........................................................31.2 Features .......................................................................3

2. SPECIFICATIONS.............................................. 33. INSTALLATION ................................................. 3

3.1 Location & Mounting......................................................33.2 Earth Ground ................................................................33.3 Power ...........................................................................43.4 Telephone Line Connection............................................43.5 Bell (Siren) Output ........................................................43.6 Programmable Output (PGM).......................................43.7 Keypad & Keyswitch Connections..................................43.8 Keypad Zone Connections.............................................53.9 Single Zone Input Connections ......................................53.10 Advanced Technology Zone (ATZ) Connections...........63.11 Fire Circuit ..................................................................7

4. ACCESS CODES ............................................... 74.1 Installer Code................................................................74.2 Master & User Codes....................................................74.3 User / Access Code Length...........................................74.4 Duress..........................................................................84.5 Installer Lock.................................................................8

5. PROGRAMMING METHODS .............................85.1 Hexa Programming .......................................................85.2 Hexa Streamlined Programming ....................................85.3 Decimal Programming...................................................95.4 Feature Select Programming .........................................95.5 Key Access Programming .............................................9

6. PANEL SETTINGS FOR VISLOAD.................... 96.1 Panel Answer Options...................................................96.2 Panel Identifier ............................................................106.3 PC Password..............................................................106.4 Computer Telephone Number......................................106.5 Call Visload.................................................................106.6 Answer Visload ...........................................................106.7 Cancel Communication................................................106.8 Call Back ....................................................................106.9 Automatic Event Buffer Transmission ..........................10

7. ZONE DEFINITIONS........................................ 107.1 Zone Speed ................................................................107.2 Advanced Technology Zoning (ATZ) ............................117.3 Intellizones ..................................................................117.4 Silent Zones................................................................117.5 “24 Hour” & Fire Zones................................................117.6 Instant Zones ..............................................................117.7 Follow Zones...............................................................117.8 Entry Delay 1 ..............................................................117.9 Entry Delay 2 ..............................................................117.10 Partitioning (Maestro-1000 only) ................................137.11 Bypass Enabled Zones..............................................137.12 EOL Zones (Enabled/Disabled)..................................137.13 Keypad Zone 1 Supervision .......................................137.14 Keypad Zone 2 Supervision .......................................13

8. EVENT REPORTING ....................................... 138.1 Reporting Options .......................................................138.2 Central Station Telephone No. 1 ..................................158.3 Central Station Telephone NO. 2..................................158.4 System Account Codes ...............................................168.5 Communicator Formats ...............................................168.6 Reporting Event Codes................................................168.7 Auto Test Report.........................................................178.8 Manual Test Report.....................................................178.9 Power Failure Report Delay .........................................178.10 Recent Close Delay...................................................188.12 Report Code Disarming Options ................................18

9. ARM/DISARM & ALARM OPTIONS ................ 189.1 “Timed” Auto Arming ..................................................189.2 “No Movement” Auto Arming .......................................199.3 “One-Key” Regular Arming ..........................................199.4 “One-Key” Home / ”System A” Arming.........................199.5 Arming Using Keyswitch or Pushbutton .......................199.6 Bell Squawk ................................................................199.7 Exit Delay....................................................................199.8 Beep on Exit Delay ......................................................199.9 Alarm Transmission Delay...........................................199.10 Silent Zones & Silent Panics Option ...........................199.11 Bell Cut-Off Time.......................................................199.12 Code Priority .............................................................19

10. PGM (PROGRAMMABLE OUTPUTS )...................... 2010.1 PGM Types...............................................................2010.2 PGM Timer Setting....................................................2010.3 PGM Options ............................................................21

11. OTHER OPTIONS.......................................... 2111.1 Telephone Line Monitoring (TLM)...............................2111.2 Dialing Options..........................................................2111.3 Dialing Pulse Rates ...................................................2111.4 Keypad Panic Options ...............................................2111.5 Panel Time................................................................2111.6 Time Correction.........................................................2111.7 Tamper/Wire Fault Recognition Options.....................2111.8 Tamper Bypass Options ............................................2211.9 Installer Test Mode....................................................2211.10 Exclude Power Failure From Trouble Display............2211.11 Audible Trouble Warning .........................................2211.12 Power Down Reset..................................................22

12. USER/KEYPAD FUNCTIONS ........................ 2212.1 Programming Master & User Codes ..........................2212.2 Regular Arming .........................................................2212.3 Away Arming.............................................................2312.4 Home Arming............................................................2312.5 Arming/Disarming Partitions ......................................2312.6 System Disarming.....................................................2312.7 Alarm Memory...........................................................2412.8 Keyswitch or Pushbutton Arming / Disarming.............2412.9 Manual Zone Bypassing ............................................2412.10 Bypass Recall .........................................................2412.11 Keypad Chime Zones ..............................................2412.12 Trouble Display Monitoring.......................................24

DE5281 3

,1752'8&7,21 ,1752'8&7,21

Thank you for placing your trust in the MAESTRO-1000 andMAESTRO-600 control panels. You have chosen a sophisticated,user-friendly control panel designed to meet all of yourtechnological, performance and security requirements.The superior capabilities of the MAESTRO-1000 and MAESTRO-600control panels are driven by leading edge hardware and software.Use of the most powerful RISC processors on the market, withbuilt-in “analog-to-digital” converters and SMD technology, meansour control panel requires 30-40% less components than anyprevious generation.The reduced number of steps required to program these controlpanels increases the speed of installation and end-users canaccess most system features at the touch of just one key. A“streamlined programming” feature further simplifies theprogramming process, by saving data automatically and leading theinstaller through the programming addresses without the need toenter them manually.Important advances have been made in MAESTRO control paneltechnology, which guarantee exceptional levels of false alarmprotection. A full range of high-tech features dramatically reducesthe frequency of false alarms. These easy to use tools include“Intellizone” definition, “Auto Zone Shutdown”, “Beep On Exit Delay”,“Programmable Delay before Alarm Transmission” and “RecentClosing” report.Each control panel can be used to monitor two distinct securitysystems. Partitioning provides a practical and flexible solution insituations where combined systems are a necessity. Zones can beassigned to “System A”, “System B”, both systems or given nosystem assignment. MAESTRO panels can reduce set-up andreporting time by transmitting pre-programmed event codes andusing high-speed communicator formats. Almost any control panelcondition or event may be used to activate the MAESTRO’Sprogrammable output (PGM). Once a panel status mode is selectedfor the PGM to follow, the polarity and duration of the output mayalso be programmed.The MAESTRO-1000 control panel includes the AdvancedTechnology Zoning (ATZ) feature, which was developed to permitconnection of 2 zones on one zone input terminal, as well asproviding wire fault recognition on both zones.

ATZ simplifies the task of meeting the zone requirements of anyinstallation while reducing installation costs.

$ERXW 7KLV 0DQXDOThis manual will provide you with all the information you will need tounderstand panel operation, features and functions. Even if you arefamiliar with other security control panels, we recommend that youread this entire manual at least once to familiarize yourself withpanel features and programming. For your convenience a“Programming Guide” is included in order to keep track of whichaddresses were programmed and how.

)HDWXUHVMAESTRO-1000: 10 zones (4 onboard inputs w/ATZ = 8 zones + 2keypad zones)MAESTRO-600: 6 zones (4 onboard inputs + 2 keypad zones)Common features • Powerful 16-bit RISC processor with built-in analog to digital

converters.

• User-friendly programming

• “False Alarm Prevention” features such as: Intellizones, AutoZone Shutdown, Beep on Exit Delay, Programmable DelayBefore Alarm Transmission, and Recent Closing Report.

• 2 Flexible Partitions (MAESTRO-1000 only)

• High-Speed Pre-Programmed or Programmable CommunicationFormats

• 256 Event Buffer with time and date stamp

• Fully Programmable Output (PGM)

• 48 User Codes, 1 Master Code, 1 Installer Code

• Telephone Line Monitoring (TLM)

• 3 panic alarms, activated via the keypad

• Regular Arming, “Home” Arming, “Double Home” Arming,“Away” Arming, “One-Key Regular Arming”, “One-Key HomeArm”, “One-Key” Exit & Re-arm, “Timed Auto Arming”, “NoMovement Auto Arming”, Keyswitch or Pushbutton Arming

63(&,),&$7,216 63(&,),&$7,216

Battery Charger: 360mA with dynamic Battery test.Aux. Power: 400mA, Fuseless electronic shutdown at 1A,Automatic restoreBell Out : 1A, Fuseless electronic shutdown at 3A, Automaticrestore

AC input: 16.5 VAC, 40VA, 50 - 60HzPGM output: N.C. or N.O to ground, 50mA Max.Serial Data Output : (1200, 1, N) for use with accessory modules(not UL systems).

,167$//$7,21 ,167$//$7,21

/RFDWLRQ 0RXQWLQJBefore mounting the cabinet, push the five white nylon-mountingstuds into the back of the cabinet. The circuit board should not bemounted into the back of the cabinet, until all cables are pulled intothe cabinet and prepared for connection. Select an installation sitethat is not easily accessible to intruders. Leave at least 2” aroundthe panel box to permit adequate ventilation and heat dissipation.The installation site should be dry and close to an AC source,ground connection and telephone line connection.

(DUWK *URXQGConnect the zone and dialer ground terminals from the control panelto the cabinet and cold water pipe or grounding rod as per localelectrical codes.

4 DE5281

3RZHU

3.3.1 AC PowerNOTE: Initial setup andpower-on must be performedwhile AC power is connected.The system will not operatewith backup battery only, duringinitialization.Use a 16.5VAC (50-60Hz)transformer with a minimum40VA rating to provide sufficientAC power.

7UDQVIRUPHU

9$& 9$

$&

32:(5

$&

Do not use any switch-controlled outlets to power the transformer.Connect the transformer as shown in fig. 2. After applying power tothe control panel, it will perform a hardware verification. Once this iscompleted, the auxiliary power terminals will be enabled in order topower all accessories connected to its terminals, such as keypadsand motion detectors. The control panel will then perform a batterytest and re-instate the last system status (i.e. alarm, system armed,etc.). The control panel will then begin displaying the current systemstatus (i.e. open/closed zones, troubles, etc.)

Caution : Do not connect the transformer or the back-up batteryuntil all wiring is completed!

3.3.2 Back-up BatteryIn case of power loss, connect aback-up battery. Use a 12VDC7Ah rechargeable acid/lead or gelcell battery. Connect the back-upbattery after applying the ACpower. When installing verifyproper polarity, as reversedconnections will blow the batteryfuse. Connect the "RED" batterylead to the positive batteryterminal, and the "BLACK"battery lead to the negativebattery terminal of the controlpanel as shown in fig. 3.

3.3.3 Auxiliary Power TerminalsThe AUX+ and AUX- terminals on the control panel can provide amaximum of 400mA 12VDC. Use the auxiliary power supply topower the motion detectors, keypads and other accessories in yoursecurity system. Although, their combined current consumptionshould not exceed 400mA. The auxiliary supply ismicroprocessor-protected against current overload andautomatically shuts down if the current exceeds 1A. Auxiliary powerwill resume once the overload condition has restored and within1-60 seconds after performing the battery test.

3.3.4 Battery TestThe Control Panel conducts a dynamic battery test under load every60 seconds. If the battery is disconnected, or its capacity is too low,the trouble indicator will illuminate on the keypad (red “1” indicator).The red “1” indicator also comes “on” if the battery voltage drops to10.5 volts or less while the control panel is running on the back-upbattery (no AC). At 8.5 volts, the panel shuts down and there is nooutputs.

3.3.5 Keypad Function TestWe recommend conducting a "power-up" test on keypads installedfar from the control panel. To do so temporarily connect thekeypads close to the control panel and connect the transformer.After 10 seconds, begin entering random commands on the keypadand verify that the keypad "beeps" in response to these commands.Then open a zone to ensure that the keypad and the control panelare responding to these signals. If the keypad does not respond andindicator lights do not illuminate, verify that approximately 16VAC ispresent at the “AC” terminals. If AC is present, check the keypadwiring and verify there isn’t a short between the "black" and "red”keypad wires. If the keypad does not respond, please contact yourlocal distributor.

7HOHSKRQH /LQH &RQQHFWLRQConnect the incoming telephone company wires into the tip and ringconnections of the control panel. Then run the wires from t1 and r1to the telephone system as shown in figure 4.

%HOO 6LUHQ 2XWSXWThe BELL+ and BELL- terminals,power bells and/or other warningdevices requiring a steady voltageoutput during an alarm. The belloutput supplies 12VDC upon alarmand can support two 20-watt or two30-watt bells output.

Caution: The bell output is microprocessor-controlled and willautomatically shut down if the current exceeds 3A.

If the load on the bell terminals returns to normal (≤3A), the controlpanel will re-instate power to the bell terminals upon generation ofanother alarm. When connecting sirens (speakers with built-in sirendrivers) please verify correct polarity. Connect the positive lead tothe BELL+ terminal and the negative lead to the BELL- terminal ofthe control panel as shown in figure 5.

3URJUDPPDEOH 2XWSXW 3*0The Maestro Control Panel includes a programmable output. Whena specific event or condition occurs in the system, the PGM can beused to reset smoke detectors, activate strobe lights, open/closegarage doors and much more. The PGM provides a 50mA output .If the current draw on the PGM output is to exceed 50mA, werecommend the use of a relay as show in figure 6. Each PGM isprogrammable to toggle on and off from more than a thousanddifferent events. For example, PGM can open and close anautomatic garage door by pressing keys [1] and [2] simultaneouslyon keypad. For details on how to program the PGM, refer to section10 PGM (Programmable Outputs).

5HOD\ IRUP &

.H\SDG .H\VZLWFK &RQQHFWLRQVConnect the four keypad connections labeled red, black, green andyellow to the corresponding color terminals on the control panel asindicated in figure 7. Connect the keyswitch, in series with 220 ohmresistor, to the GRN/BLK terminals of the control panel as shown infigure 7. Refer to sections Arming Using Keyswitch and keyswitchor Pushbutton Arming (section 12.8) for more information onkeyswitches.

DE5281 5

RKP

.H\SDG =RQH &RQQHFWLRQVEach keypad comes with one zone input terminal, allowing you toconnect one detector or door contact directly to the keypad.

Example: A door contact located at the entry point of anestablishment can be wired directly to the zone input terminal ofthe entry point keypad instead of wiring the door contact all theway to the control panel.

The keypad will communicate the status of the zone to the controlpanel as though the input was on the control panel. Therefore,adding one or two zones to your security system. Regardless of thenumber of keypads in the system, the control panel supports amaximum of two keypad zones.

Example: A security installation is comprised of four keypads. Ofthese four keypads only two can have their zone input terminalsenabled (see figure 9). The other two keypads must have theirzone input terminals disabled as described below.

Keypad’s whose zone input terminals are not being used, must bedisabled. To disable the Maestro-601 keypad zone, connect a 1KΩresistor short between the ZONE and BLK terminals of the keypad.On the other hand, if you are using the keypad zones, you mustdefine them as either Keypad Zone 1 or Keypad Zone 2 asdescribed below.Note : if using two keypad zones, one keypad must be defined askeypad zone 1 while the other must be defined as keypad zone 2.The control panel will recognize these added zones as shown intable 1.Once the keypad zones have been defined, you must enable“Keypad Zone Supervision” in the control panel (see section 7.13and 7.14.). Figures 8 and 9 demonstrate typical keypad zone inputinstallations. Note that keypad zones always use a 1KΩ EOLresistor.

Figure 10 describes the keypad tamper switch connections.NOTE: The standard KP-601 does not include a tamper switch. In caseyour version includes a tamper switch, see figure 10 for wiringinstructions.

Table 1 – Keypad Zone Recognition

Zone Select Jumper “OFF” = Keypad Zone 1Zone Select Jumper “ON” = Keypad Zone 2

Note: If the zone select jumper is changed, the control panel will onlyrecognize the change when the keypad is disconnected and re-connected.

MAESTRO-1000 MAESTRO-600

(ATZ Disabled) (ATZ Enabled)

Kpd Zone 1 = Zone “5” Kpd Zone 1 = Zone “9” Kpd Zone 1 = Zone “5”

Kpd Zone 2 = Zone “6” Kpd Zone 2 = Zone “10” Kpd Zone 2 = Zone “6

6LQJOH =RQH ,QSXW &RQQHFWLRQVThe system hardware recognizes the following single zone inputterminal connections. For more information on programming theoptions mentioned below refer to ZONE DEFINITIONS, section 7.

6 DE5281

3.9.1 N.C. Contacts, Without EOL ResistorIf your security installation does not require tamper or wire faultdetection, connect the detection devices and program the controlpanel as shown in figure 11. This setup will communicate an openor closed zone to the control panel, illuminating the correspondingindicator on the keypad when the zone is open. Do not use deviceswith normally open contacts in this setup, as this will cause thecontrol panel to remain in alarm.

3.9.2 N.O. and N.C. Contacts, With EOL ResistorIf your security installation does not require tamper or wire faultrecognition but requires the use of normally open and normallyclosed contacts, connect all detection devices with a 1KΩ end ofline (EOL) resistor and program the control panel as shown infigures 12 and 13. This setup will communicate an open or closedzone to the control panel, illuminating the corresponding indicator onthe keypad when the zone is open.

3.9.3 N.C. Contacts, Without EOL Resistor, WithTamper RecognitionIf your security installation requires tamper recognition, all detectiondevices must use normally closed contacts. Connect the devicesand program the control panel as shown in figure 14. This setup willcommunicate an open or closed zone to the control panel,illuminating the corresponding indicator on the keypad when thezone is open. The control panel will also communicate any detectedtampers (cuts) as Tamper/Wire Fault Recognition Options (seesection 11.7).

3.9.4 N.C. Contacts, With EOL Resistor, WithTamper and Wire Fault RecognitionIf your security installation requires tamper (cut) and wire fault(short) recognition, all detection devices must use normally closedcontacts. Connect the devices and program the control panel asshown in figure 15. This setup will communicate an open or closedzone to the control panel, illuminating the corresponding key on thekeypad when the zone is open. The control panel will alsocommunicate any detected tampers (cuts) and/or wire faults (short)as per Tamper/Wire Fault Recognition Options (see section 11.7).

$GYDQFHG 7HFKQRORJ\ =RQH $7=

&RQQHFWLRQVEnabling the ATZ feature (see section 7.2) allows you to install twodetection devices per input terminal, therefore, doubling zonecapacity of the control panel. Advanced Technology Zoning is asoftware-oriented feature, there is no need for extra modules, simplyinstall the devices as shown in figures 17 to 19. The control panelwill recognize and display the status of the installed devices asshown in figure 16. The extra zones, function exactly like any otherzone, displaying zone status on the keypad and sending separatealarm codes for each zone. For more information on programmingthe options mentioned in the following sections refer to ZoneDefinitions section.NOTE: This feature is not available on the MAESTRO-600 ControlPanel!

3.10.1 ATZ N.C. Contacts, Without EOL ResistorIf your security installation does not require tamper or wire faultrecognition but requires the use of two zones per input, connect thedetection devices and program the control panel as shown in figure17. Do not use devices with normally open contacts, as this willcause the system to remain in alarm. This setup will communicatethe status of each device to the control panel (see figure 16), wherean open zone will illuminate the corresponding LED indicator on thekeypad.

3.10.2 ATZ N.C. Contacts, Without EOL Resistor,With Tamper RecognitionIf your security installation requires tamper recognition and twozones per input terminal, connect the detection devices and

DE5281 7

program the control panel as shown in figure 18. Do not use deviceswith normally open contacts, as this will cause the zone to remainopen. This setup will communicate the status of each zone to thecontrol panel (see figure 16), where an open zone will illuminate thecorresponding LED indicator on the keypad. The control panel willalso communicate any detected tampers (cuts) on the system asper Tamper/Wire Fault Recognition Options (see section 11.7).

3.10.3 ATZ N.C. Contacts, With EOL Resistor, WithTamper & Wire Fault RecognitionIf your system requires tamper (cut) and wire fault (short)recognition, connect the two detection devices to one input terminalwith a 1KΩ end of line (EOL) resistor and program the control panelas shown in figure 19. Do not use devices with normally opencontacts, as this will cause the zone to remain open. This setup willcommunicate the status of each zone to the control panel (seefigure 16), where an open zone will illuminate the correspondingLED indicator on the keypad. Any tampers (cuts) and/or wire faults(shorts) detected on the system are communicated as perTamper/Wire Fault Recognition Options (see section 11.7).

)LUH &LUFXLWIf your security installation requires the use of smoke detectors, youmust define zone 3 as a “24-hour fire” zone; please refer to section7.5.

3.11.1 Standard InstallationConnect the smoke detectors to zone 3 as shown in figure 20. Notethat a fire zone must use a 1KΩ EOL resistor. If there is a line shortor if the smoke detector becomes active, whether the system isarmed or disarmed the control panel will generate an

alarm. If the line is "open", the control panel will send a "fire loop"trouble report to the central station and illuminate the “TRBL”indicator on the keypad.

3.11.2 Supervised 4-Wire, Latched, Smoke DetectorInstallationTo reset (unlatch) the smokedetectors after an alarm,momentarily interrupt power tothe detectors. To do so, verifythat the negative (-) of the smokedetectors are connected to thePGM.To supervise the power supply,install an “end of line” relay (relayform “C”). Connect the smokedetectors and relay as shown infigure 21. In the event power isinterrupted the relay will cause afire trouble report (see section7.5, “24 Hour” & Fire Zones.)

Set the PGM for “Timed N.C.” (normally closed), and program thePGM to “open” when any two keys on the keypad are pressedsimultaneously. For more information on programming the PGMrefer to section 10 PGM (Programmable Outputs)

EXAMPLE:To program the PGM to conduct a smoke detector reset whenthe [ CLR] and [ENT] keys are pressed at the same time.Address 039 = [ BYPASS] [2ND]Address 040 = [5] [0]Address 042 = [2 ND] [6]Address 056 = [0] [0] [4]

$&&(66 &2'(6 $&&(66 &2'(6

,QVWDOOHU &RGHStreamline (for description, see Programming Guide) - Section 00Î Hexa Programming - Addresses 000-002Default = 1111Only the installer code provides you with access to program allsettings in the control panel. Only the Master and User accesscodes can not be programmed using the installer code. To programany setting in the control panel you must enter the programmingmode by pressing the [ENT] key followed by the Installer Code. Theinstaller code contains six digits and each digit can be any valuefrom 0 to 9. When programming the installer code, always enter sixdigits.[ENT] + [INSTALLER CODE] + [0] [0] [0] + First 2 digits + [0] [0] [1] +Next 2 digits + [0] [0] [2] + Final 2 digits + [ENT]

0DVWHU 8VHU &RGHVDefault Master Code: 0000Please note you can not use the Installer Code to program theMaster and User codes. Only the Master and User 1 Codes canprogram these codes. For details on Programming Master & UserCodes go to section 12.1.

8VHU $FFHVV &RGH /HQJWKFeature Select Programming Î Address 088, key [9].Default: 4-digit Access Codes.When entering an access code into the control panel, the controlpanel can grant access after entering all six digits or after enteringthe first four digits of the code.

8 DE5281

LED “9” off: 4-digit Access CodesLED “9” on: 6-digit Access Codes[ENT] + [installer code] + [0] [8] [8] + “9” On/Off + [ENT] + [ENT]

'XUHVVFeature Select Programming Î Address 090, key [0]Default: Duress DisabledWhen unwillingly forced to disarm a system, entering User Code#48 instead of the usual code, will disarm the system and send asilent alert (Duress Code) to the Central Station.LED “10” off: Duress Disabled

LED “10” on: Duress Enabled[ENT] + [installer code] + [0] [9] [0] + “10” On/Off + [ENT] + [ENT]

,QVWDOOHU /RFNDecimal Programming Î Address 058Default: Address EmptyProgram 147 into address 058 to enable the installer lock. Hence, ahardware reset (see section Power Down Reset) will not affect thecurrent settings. To remove the installer lock, enter any value otherthan 147.[ENT] + [installer code] + [0] [5] [8] + [1] [4] [7] + [ENT]

352*5$00,1* 0(7+2'6 352*5$00,1* 0(7+2'6

When programming, use the supplied “Programming Guide” to keeptrack of which addresses were programmed and how. Before youbegin programming the control panel, we recommend you readsections 5 through 11 of this manual in order to acquire a goodunderstanding of the control panel and its many features. Whenprogramming with the keypad, certain addresses are programmedusing different methods. These methods are described in detailbelow. Each section in this manual will reference the appropriateprogramming method.

+H[D 3URJUDPPLQJAddresses 000 to 043 and 300 to 527 are programmed using theHexa Programming method. In this mode, you can enter anyhexa-digit from 0-F where keys [1] to [9] represent digits 1 to 9respectively; the other keys represent hexa digits A to F as shownin figure 22. To program using the Hexa Programming method: 1 . Press [ENT] + [installer code] 2 . The red “PRG” indicator will flash indicating you are in

programming mode

3 . Enter the desired [3-digit address] and the red “PRG” indicatorwill remain illuminated.

4 . The keypad will display the 2-digit data currently saved at thisaddress as described in figure 23

5 . Enter [2-digit data]; after entering data you do not need to press[ENT], the software will automatically save the data into theselected address.

6 . Return to step 2 to continue programming or press [CLR] to exitprogramming mode.

+H[D 6WUHDPOLQHG 3URJUDPPLQJThis is an alternate method to Hexa Programming. The addresses(000-043 and 300-527) programmed in the Hexa Programmingmethod are grouped into 67 sections where each section containsfour addresses (i.e. section 11 = addresses 300-303). Using thismethod allows you to program 8 digits (4 addresses) without havingto exit and re-enter addresses. When entering the final digit, thesoftware will automatically advance to the next section.Example: If you complete the “Programming Guide” with thedesired data, you can program the 67 sections by entering all 567digits without pressing [ENT] or entering any other addresses.

This makes for quicker programming.Note, the keypad will not display the current data in the HexaStreamlined Programming method. To program using the HexaStreamlined Section method: 1 . Press [ENT] + [installer code] + [7].

2 . The red “PRG” and “2nd” LED indicators will flash to indicateyou are in programming mode.

3 . Enter [2-digit section] (00-67)

4 . The red “PRG” indicator will remain on and “2nd” LED indicator willturn off.

5 . Enter [8-digit data] to program the section. 6 . The keypad will sound a confirmation “beep” to indicate that the

section has been programmed, data is saved and that thesoftware has advanced to the next section.

7 . Return to step 5 to continue programming at the next address orpress [CLR] to exit the programming mode.

DE5281 9

'HFLPDO 3URJUDPPLQJAddresses 044 to 061 are programmed using the DecimalProgramming method. Values entered must contain three digitsfrom 000 to 255.To program using the Decimal Programming method: 1 . Press [ENT] + [installer code] 2 . The red “PRG” indicator will flash to indicate you are in

programming mode 3 . Enter [3-digit address] (044-061) and the “PRG” indicator will

remain on

4 . The keypad will now display the 3-digit data currently saved atthis address as described in figure 24

5 . Enter [3-digit data] (000-255); after entering data you do notneed to press [ENT], the software will automatically save thedata into the selected address.

6 . Return to step 2 to continue programming or press [CLR] to exitprogramming mode

)HDWXUH 6HOHFW 3URJUDPPLQJAddresses 062 to 126 are programmed using the Feature SelectProgramming method. In this method, each key in every addressrepresents an option or feature. Pressing a key will illuminate thecorresponding LED indicator on the keypad and pressing the keyagain will extinguish the indicator. The On/Off status of each lightdetermines the selected features. To program using the FeatureSelect Programming method: 1 . Press [ENT] + [installer code] 2 . The red “PRG” indicator will flash to indicate you are in

programming mode

3 . Enter [3-digit address] (062-126) 4 . After entering the address, the keypad will display the feature

selection status. The On/Off status of the keypad LED indicatorsdetermines the selected features as described in the“Programming Guide” and in the appropriate sections of thismanual. Turn the LED indicators on/off by pressing thecorresponding key until the desired options are set. Then pressthe [ENT] key to accept, there will be a confirmation “beep”indicating the options have been accepted. The “PRG” indicatorwill flash to indicate that the software is awaiting the nextaddress entry

5 . Return to step 3 to continue programming or press [CLR] to exitprogramming mode

.H\ $FFHVV 3URJUDPPLQJThis method allows for quick programming of features withoutentering addresses or section numbers. The following features areprogrammed using the installer code as well as the master and user1 codes. • Auto Arm Time: for details see parag. 9.1.1 • Panel Time: for details see parag. 9.5 • Manual Test Report: for details see parag. 8.8

3$1(/ 6(77,1*6 )25 9,6/2$' 3$1(/ 6(77,1*6 )25 9,6/2$'

3DQHO $QVZHU 2SWLRQVStreamline - Section 00 Î Hexa Programming - Address 003Default: Answering Machine Override Disabled & Maximum 8 rings.The following two options will define how the control panels answeran incoming call from a computer using the Visload software.In order for the Visload software to remotely communicate with thecontrol panel, call the installation site twice using the VisloadSoftware. To do so, program the first digit in address 003 with anyvalue from 1-F (see table 2 at the end of this section), this valuerepresents the delay period the control panel will wait between thefirst and second call. Using the Visload software, call the installationsite and on the second ring press [enter] on the keyboard tohang-up. After hanging up, the Visload software will immediately callthe installation site back. If the installation site is called back withinthe programmed delay period, the control panel will override theanswering machine or service by picking-up on the first ring. Todisable this option program [2nd] or [1] as the first digit in address003.Example: A security installation is using an answering machine setto answer after 3 rings, the first digit at address 003 has beenprogrammed with [5] (40 sec.) and the second digit has beenprogrammed with 8. When you call the installation site with theVisload software the first time, wait two rings and press [enter] onthe keyboard. The Visload software will immediately call theinstallation site back. If the second call is made within 40 seconds,

the panel will pick up the line on the first ring. If it takes more than40 seconds, the panel will not answer on the first ring and theanswering machine will answer after three rings.[ENT] + [installer code] + [0] [0] [3] + 1st digit + 2nd digit (1-15rings) + [ENT]The second digit represents the number of rings the control panelwill wait before picking-up the line. If the line is not answered afterthe number of re-programmed rings, the control panel will answerthe call. Note the control panel resets the "ring" counter every 64seconds. Therefore, if someone or an answering machine answersa call before the number of pre-programmed rings has elapsed, thecontrol panel will keep the number of rings in memory for 64seconds. If you hang-up and call the installation site back within 64seconds, the control panel will continue to count the number of ringsfrom the first call. After reaching the total number of rings, thecontrol panel will answer the call. The number of rings can be setfrom 1-15 by programming the second digit at address 003 with anyhexa-digit from 1-F. Program the second digit with [2nd] to disablethis option.Example: Address 003 = [2nd] [8]. Using the Visload software, youcall an installation site where there is no answering machine orservice and no one is home. Since there is no one to answer thetelephone call, the control panel will pick-up the line on the eighthring. If someone happens to be home and answers the telephone,say, after three rings, the control panel will keep the three rings inmemory for 64 seconds. If you hang-up and call back the installation

10 DE5281

site within 64 seconds the control panel will answer the call on thefifth ring. If you call back after 64 seconds the "ring" counter willhave been reset and the control panel will answer the call on theeighth ring.NOTE: If you program four or less rings, the control panel willalways reset the counter!

Table 2 - Answering Machine Override Options[2nd] or [1] = Answering Machine Override disabled[2] = 16 sec. [4] = 32 sec. [6] = 48 sec. [8] to [TRBL] = 60 sec.[3] = 24 sec. [5] = 40 sec. [7] = 56 sec.

Note: for more details, refer to the Programming Guide -Streamline section “00” and “014”.

3DQHO ,GHQWLILHUStreamline - Section 01 Î Hexa Programming - Addresses004-005This four-digit code identifies the control panel to the Visloadsoftware before initiating upload. Program the same 4-digit code intothe control panel and the Visload software before attempting toestablish communication. If the codes do not match, the controlpanel will not establish communication. Enter any hexa digits from 0to F.[ENT] + [installer code] + [0] [0] [4] + First 2 digits + [0] [0] [5] +Final 2 digits + [ENT]

3& 3DVVZRUGStreamline - Section 01 Î Hexa Programming - Addresses006-007This four-digit download password identifies the PC to the panel,before beginning the download process. Enter the same passwordinto the Visload software and the control panel. If the passwords arenot the same, Visload will not establish communication. Enter anyhexa digits from 0 to F.[ENT] + [INSTALLER CODE] + [0] [0] [6] + First 2 digits + [0] [0] [7] +Final 2 digits + [ENT]

&RPSXWHU 7HOHSKRQH 1XPEHUStreamline Section 02 & 03 Î Hexa Programming - Address008-015The control panel will dial this telephone number when trying toinitiate communication with the PC (see section 6.5 Call Visload).There is no default telephone number and you can enter anynumber from 0-9 up to a maximum of 16 digits. If you would like toenter any special keys or functions refer to table 3 in section 8.3. Ifthe telephone number contains less than 16 digits, press the [TRBL]key to indicate the end of the telephone number.[ENT] + [INSTALLER CODE] + [7] + [0] [2] + Telephone Number (if<16 digits press [TRBL]) + [ENT]

&DOO 9LVORDGKey Access Programming Î key [TRBL]The control panel will dial the telephone number entered ataddresses 008-015 (see section 6.4) in order to communicate withthe Visload software. The control panel and the computer will verifythat the Panel Identifier and the PC Password match beforeestablishing communication (see sections 6.2 and 6.3).Press [ENT] + (Installer, Master, or User 1 Code) + [TRBL]

$QVZHU 9LVORDGKey Access Programming Î Key [AWAY]

By entering the code sequence listed below, you can manually forcethe control panel to answer any incoming calls from the Visloadsoftware. This option can also be used to perform an on-siteupload/download by connecting your computer directly to the controlpanel using an ADP-1 line adapter (ADP-1 is a module that can be used

to connect a modem directly to the panel without the phone line) andmanually answering Visload from the control panel. In Visload go to:Main Menu Î Program Setup Î Setup Î Modem & PrinterConfigurationSet "Dialing Condition" to "Blind Dial". Program the panel telephonenumber in Visload and follow the instructions on the ADP-1 adapter.When the computer has dialed press:[ENT] + (Installer, Master, or User 1 Code) + [AWAY]

&DQFHO &RPPXQLFDWLRQKey Access Programming Î key [HOME]Use the Installer Code to cancel all communication and erase anyunreported events in the buffer until the next reportable event. Usethe Master or User 1 code to cancel communication attempts withVisload.[ENT] + (Installer, Master & User 1 Code) + [HOME]

&DOO %DFNFeature Select Programming Î Address 086, key [4]Default: Call Back DisabledFor additional security, when a PC using the Visload softwareattempts to communicate with the control panel, the control panelcan hang-up and call the PC back in order to re-verify identificationcodes and re-establish communication. When the control panelanswers the call, it will verify if the Panel ID and PC Passwordsmatch and if they do, the control panel will hang-up and call theVisload software back. The Visload software will automatically gointo "wait for dial tone", ready to answer when the control panel callsback. Please note the Computer Telephone Number (see section6.4) must be programmed in order to use the "Call Back" feature.LED “4” off: Call Back DisabledLED “4” on: Call Back Enabled[ENT] + [INSTALLER CODE] + [0] [8] [6] + “4” On/Off + [ENT] + [ENT]

$XWRPDWLF (YHQW %XIIHU

7UDQVPLVVLRQFeature Select Programming Î Address 088, key [2nd]Default: Automatic Event Buffer Transmission DisabledWhen the event buffer reaches 50% capacity, the control panel willmake two attempts to establish communication with a PC. Thecontrol panel will call the Computer Telephone Number (see section6.4) programmed at addresses 008 to 015. The Visload softwaremust be in "wait for dial tone" mode. When the system establishescommunication, it will upload the contents of the event buffer to theVisload software. If communication is interrupted beforetransmission of the complete contents of the buffer, or if after twoattempts, communication is not established, the system will waituntil the event buffer is full before attempting to re-communicatewith Visload. When Event Buffer is full, each subsequent new eventwill erase the oldest event in the buffer.LED “2nd” off: Automatic Event Buffer Transmission DisabledLED “2nd” on: Automatic Event Buffer Transmission Enabled[ENT] + [INSTALLER CODE] + [0] [8] [8] + “2ND” On/Off + [ENT] + [ENT]

=21( '(),1,7,216 =21( '(),1,7,216

Note: When defining zones characteristics, refer to “zonedefinition” table, in the programming guide.

=RQH 6SHHGDecimal Programming Î Address 053Default: 600mS

The zone speed applies to all zones whether the system is armed ordisarmed. The zone speed defines how quickly the control panel willrespond to an open zone. The control panel will not display and/orrespond to an open zone until the programmed zone speed elapses.All other zone definitions and options do not come into effect untilthe zone speed has elapsed.

DE5281 11

Example: The system is armed and the zone speed is set for 1.2seconds. A zone opens and closes in less than 1.2 seconds, thecontrol panel will respond as though nothing happened (i.e. noreporting, no alarm and no display on keypad).The zone speed can be set from 15ms to 3.8s (001 to 255 X15ms). This feature prevents any momentary glitches in the systemfrom causing an alarm or unnecessary reporting.[ENT] + [installer code] + [0] [5] [3] + 3 digit decimal value (001-255)+ [ENT]

$GYDQFHG 7HFKQRORJ\ =RQLQJ

$7=Feature Select Programming Î Address 090, key [8]Default: ATZ DisabledNOTE: This feature is not available on the Maestro-600 ControlPanel!Enabling the ATZ feature allows you to install two detection devicesper zone input. Each detection device will have its own zone andeach will transmit a separate alarm code that will display on thekeypad. For information on how to connect the detection devicesand how the panel recognizes them, please refer to sectionAdvanced Technology Zone (ATZ) Connections .LED “8” off: ATZ DisabledLED “8” on: ATZ Enabled[ENT] + [installer code] + [0] [9] [0] + “8” On/Off + [ENT]

,QWHOOL]RQHVFeature Select Programming Î Address 092, keys [1] to [0]If an alarm condition occurs on a zone identified as Intellizone, thecontrol panel will not trigger an alarm until one of the followingconditions occurs within a specified period (see Intellizone TimeDelay, section 7.3.1): • An alarm condition occurs on another zone. • The zone that is in alarm has restored and re-occurred. • The zone that is in alarm remains in alarm the entire period.Note the Intellizone timer will only begin after the Zone Speed periodhas elapsed (see section 7.1).

CAUTION: Do not use the Intellizone feature on zonesprogrammed with any Entry Delay! An alarm may occur whendisarming the system.

7.3.1 Intellizone Time DelayDecimal Programming Î Address 057Default: 48 secondsYou can set the Intellizone Time Delay between 010 and 255seconds. This is the period specified for Intellizones to detect one ofthree conditions before generating an alarm (see Intellizones,section 7.3).[ENT] + [installer code] + [0] [5] [7] + 3-digit decimal value(010-255) + [ENT]

6LOHQW =RQHVFeature Select Programming Î Address 096, keys [1] to [0]Using the “Feature Select Programming Method”, identify or selectwhich zones will be defined as Silent Zones. If an alarm occurs on aSilent Zone, the control panel will report the alarm (see EventReporting on section 8) to the central station without triggering anybells. If zone 3 is defined as a 24 hour (fire zone), the control panelwill generate an audible alarm overriding a silent zone definition.

´ +RXUµ )LUH =RQHVFeature Select Programming Î Address 100, keys [1] to [0]Using the “Feature Select Programming Method”, identify or selectwhich zones will be defined as 24 hour zones. Whether the systemis armed or disarmed, open “24 hour” zones always generate analarm. However, if zone 3 is defined as “24 hour”, it becomes a“Fire Zone”. Connect the smoke detectors as described in sectionFire Circuit. An open “Fire Zone” will generate the following: • The control panel will send a fire loop trouble report (address

500) to the Central Station.

• A trouble indicator, “HOME”, and a fire zone indicator, “3”, willflash on the keypad.

• Alarms will generate an intermittent output signal asdemonstrated by the figure below, regardless of the system’scurrent arming status.

• Alarms are always audible, regardless of other settings.

%(// 287387 '85,1* ),5( $/$50

7.5.1 Zone 4 (Enable/Disable)Feature Select Programming Î Address 090, key [1]Default: Zone 4 EnabledIf the ATZ feature is enabled and zone 3 has been set as a firezone, zone 4 must be disabled if it is not going to be used.LED “1“ off: Zone 4 EnabledLED “1“ on: Zone 4 Disabled[ENT] + [installer code] + [0] [9] [0] + “1” On/Off + [ENT]

,QVWDQW =RQHVFeature Select Programming Î Address 104, keys [1] to [0]Using the “Feature Select Programming Method”, identify or selectwhich zones will be defined as Instant Zones. If an “Instant” zoneopens, the control panel will immediately generate an alarm after the“Zone Speed” has elapsed.

)ROORZ =RQHVFeature Select Programming Î Address 108, keys [1] to [0]Using the “Feature Select Programming Method”, identify or selectwhich zones will be defined as Follow Zones. Follow zones functionas follows: • If a follow zone opens and no entry delay zones have been

triggered, the control panel will generate an alarm immediatelyafter the zone speed has elapsed.

• If a follow zone opens during another zone's entry delay period,the control panel will wait until the end of the entry delay periodbefore generating an alarm.

• If a follow zone opens when more than one entry delay zone hasbeen triggered, the control panel will wait until end of the entrydelay zone that opened first, before generating an alarm.

(QWU\ 'HOD\ Decimal Programming Î Address 050Default: 45 secondsAny zone that has not been identified as Instant Zones, FollowZones, Entry Delay 2 or “24 Hour” & Fire Zones will automaticallydefault to Delay 1. You can program the Delay 1 period between001 and 255 seconds into address 050. If a zone defined as Delay 1opens in an armed system, the control panel will wait theprogrammed period before generating an alarm. This allows timefor users to disarm the system when entering the protected area.[ENT] + [installer code] + [0] [5] [0] + 3-digit decimal value(001-255) + [ENT]

(QWU\ 'HOD\ Feature Select Programming Î Address 112, keys [1] to [0]Using the “Feature Select Programming Method”, identify or selectwhich zones will be defined as Entry Delay 2 Zones. If a zonedefined as Delay 2 opens in an armed system, the control panel willwait the Entry Time Delay 2 (see section 7.9.1) period beforegenerating an alarm. This allows time for users to disarm thesystem when entering the protected area.

12 DE5281

Figure 25 - Zone Related Features

Sec. 7.8

Sec. 7.8

Sec. 7.9

Sec. 7.9.1

Sec. 7.7

Sec. 7.6

Sec. 7.13and 7.14

Sec. 7.4

Sec. 7.11.1

Sec. 7.3.1

Sec. 7

Sec. 7.3

Sec. 7.11

Sec. 7.10

Sec. 7.10.2

Sec. 7.10.1

Sec. 7.1

Sec. 7.12

Sec. 7.2

DE5281 13

7.9.1 Entry Time Delay 2Decimal Programming Î Address 051Default: 45 secondsThis applies to all zones defined as Delay 2 (see Entry Delay 2above). You can program the Delay 2 between 001 and 255seconds (default 45 seconds).[ENT] + [installer code] + [0] [5] [1] + 3-digit decimal value(001-255) + [ENT]

3DUWLWLRQLQJ 0DHVWUR RQO\Feature Select Programming Î Address 086, key [8]This feature divides the alarm system into two distinct systems,identified as “System A” and “System B”. You can assign eachzone to System A, System B, both systems, or neither system.Partitioning works as follows: • Zones assigned to System A, will arm/disarm when the system is

“System A Armed/Disarmed”. • Zones assigned to System B, will arm/disarm when the system is

“System B Armed/Disarmed”. • Zones assigned to both systems (“dual area”) will arm when the

system is either “System A Armed”, “System B Armed” or whenboth systems are armed and will disarm only when both systemsdisarm.

• Zones not identified to any system (“common area”) will arm onlywhen the system is both “System A Armed” and “System BArmed” and will only disarm when at least one of the two systemsdisarms.

For more information on arming and disarming partitions, seesection 12.5, Arming/Disarming Partitions. Also, refer to CodePriority in section 9.12.

7.10.1 “System A”/Home ZonesFeature Select Programming Î Address 116, keys [1] to [0]Using the “Feature Select Programming Method”, select whichzones will be assigned to “System A” or if the system isn’tpartitioned the zones will be identified as Home Zones. For detailson “System A” zones refer to Partitioning above. For details onHome Arming (see section 12.4).

7.10.2 “System B” ZonesFeature Select Programming Î Address 120, keys [1] to [0]Using the “Feature Select Programming Method”, select whichzones will be assigned to “System B”. For details on “System B”zones refer to Partitioning above.

%\SDVV (QDEOHG =RQHVFeature Select Programming Î Address 124, keys [1] to [0]Using the “Feature Select Programming Method”, select whichzones will be defined as Bypass Enabled. Only zones defined asbypass enabled can be used for Manual Zone Bypassing (seesection 12.9, Manual Zone Bypassing) or during Auto ZoneShutdown (see section 7.11.1).

7.11.1 Auto Zone ShutdownFeature Select Programming Î Address 086 key [TRBL]Default: DisabledThe control panel will automatically bypass any “Bypass EnabledZones” which initiate 5 consecutive alarms in the same-armedperiod. Therefore, the zone will no longer generate an alarm. Afterthe control panel has bypassed a zone, it will report an event codeto the Central Station if programmed at addresses 448-461 (seeReporting Event Codes, section 8.6).This feature is a function of the Report Zone Restore Options (seesection Report Zone Restore Options). If this option is set forReport zone restore on bell cut-off, the zone will only be bypassedafter the bell or siren has cut-off 5 consecutive times in the samearmed period. While if the option is set for report zone on zoneclosure, the zone will be bypassed when the zone has opened andclosed 5 consecutive times in one armed period.LED “TRBL” off: Auto Zone Shutdown DisabledLED “TRBL” on: Auto Zone Shutdown Enabled[ENT] + [installer code] + [0] [8] [6] + “TRBL” On/Off + [ENT]

(2/ =RQHV (QDEOHG'LVDEOHGFeature Select Programming Î Address 088; key [MEM]Default: EOL input enabled

If the system is using 1KΩ end of line resistors on zone inputterminals, enable this feature (see Zone Connections in section 3.8).LED “MEM” off: Input Zones use EOL ResistorsLED “MEM” on: Input Zones do not use EOL Resistors[ENT] + [installer code] + [0] [8] [8] + “MEM” On/Off + [ENT]

.H\SDG =RQH 6XSHUYLVLRQFeature Select Programming Î Address 090, key [home]Default: DisabledIf using a keypad zone defined as keypad zone 1, enable thisfeature. When enabled, the control panel will verify for the presenceof a keypad and the keypad zone. For more information, seeKeypad Zone Connections in section Keypad Zone Connections insection 3.8.LED “HOME” off: Keypad Zone 1 DisabledLED “HOME” on: Keypad Zone 1 Enabled[ENT] + [installer code] + [0] [9] [0] + “HOME” On/Off + [ENT]

.H\SDG =RQH 6XSHUYLVLRQFeature Select Programming Î Address 090, key [away]Default: DisabledIf using a keypad zone defined as keypad zone 2, enable thisfeature. When enabled, the control panel will verify for the presenceof a keypad and the keypad zone. For more information, seeKeypad Zone Connections in section 3.8.LED “AWAY” off: Keypad Zone 2 DisabledLED “AWAY” on: Keypad Zone 2 Enabled[ENT] + [installer code] + [0] [9] [0] + “AWAY” On/Off + [ENT]

(9(17 5(3257,1* (9(17 5(3257,1*

5HSRUWLQJ 2SWLRQVFeature Select Programming Î Address 086, key [HOME] & [AWAY]Default: Reporting DisabledWhen a specific event occurs in the system, the control panel willattempt to report the appropriate event code to the Central Station.The Reporting Options define where the event codes are reported.In order to establish communication with the Central Station, thecontrol panel will first access a telephone line and wait a maximumof eight seconds for a dial tone. If a dial tone is recognized or if aftereight seconds there is no dial tone, the control panel will dial theappropriate Central Station Telephone Number as defined by theReporting Options listed in the table below. Once communication isestablished, the control panel will transmit the events in the eventbuffer to the Central Station. If communication fails during

transmission, the control panel will dial the next central stationtelephone number, as defined by the reporting options and reportonly those events not reported during the interrupted attempt. Formore information on Reporting Event Codes (see section 8.6).[ENT] + [installer code] + [0] [8] [6] + “HOME” & “AWAY” On/Off +[ENT]

“HOME”

“AWAY”

Reporting Feature

OFF OFF Reporting Disabled

OFF ON Regular Reporting

ON OFF Split Reporting

ON ON Double Reporting

14 DE5281

Sec. 8.5.3

Sec. 8

Sec. 8.3

Sec. 8.2

Sec. 8.5.4

Sec. 8.5.2

Sec. 8.5.1Sec. 8.5

Sec. 8.1

Sec. 8.1.3

Sec. 8.1.4

Sec. 8.1.2

Sec. 8.1.1

Sec. 8.4

DE5281 15

8.1.1 Reporting DisabledThe Control Panel will never transmit any event codes to the centralstation.

8.1.2 Regular ReportingUsing regular reporting the event codes are reported to the centralstation using either telephone number 1 or 2. The control panel willbegin by dialing central station telephone number 1. Ifcommunication fails, the dialer will hang up, wait a pre-determinedperiod and dial central station telephone number 2. This sequencewill repeat 4 times, switching back and forth between the 1st and2nd number (see figure 27) until communication is established.After eight unsuccessful dialing attempts, the redial sequence endsand a "communicator report failure" will appear in the keypad’strouble display (LED “7” on). When the next event occurs(reportable or non-reportable), the control panel will begin the dialingsequence again.

8.1.3 Split ReportingWhen the system is not in alarm, the control panel will report allEvent Codes to Central Station Telephone 2. If communication fails,the dialer will hang-up, wait a pre-determined period and dial thenumber again. The control panel will dial the number eight timesuntil communication is established (see figure 27). After eightunsuccessful dialing attempts, the redial sequence ends and a"communicator report failure" will appear in the keypad’s troubledisplay (LED “7” on). When the next event

occurs (reportable or non-reportable), the control panel will beginthe dialing sequence again.When the system is in alarm, the control panel will report all EventCodes to Central Station Telephone 1. Any ongoing communicationwill stop immediately and the panel will dial Telephone 1. Ifcommunication fails, the dialer will hang-up, wait a pre-determinedperiod and dial the number again. The control panel will dial thenumber eight times until communication is established (see figure27). After eight unsuccessful dialing attempts, the redial sequenceends and a "communicator report failure" will appear in the keypad’strouble display (LED “7” on). When the next event occurs(reportable or non-reportable), the control panel will begin the dialingsequence again.

8.1.4 Double ReportingIn double reporting, the control panel will report each event code toboth central station telephone numbers. The control panel will beginby attempting communication with central station telephone 1 and ifcommunication fails, the dialer will hang-up, wait a pre-determinedperiod and dial the number again. The control panel will dial thenumber eight times until communication is established (see figure27). After eight unsuccessful dialing attempts, the redial sequenceends and a "communicator report failure" will appear in the keypad’strouble display (key [7] "on"). If communication has beenestablished and the event codes transmitted or if after eightattempts communication has not been established, the control panelwill report the same Event Codes to Central Station Telephone 2.

&HQWUDO 6WDWLRQ 7HOHSKRQH 1R Streamline - Section 04 & 05 Î Hexa Programming - Addresses016-023The control panel will dial the programmed telephone number whenreporting an event code to the central station computer (seeReporting Options in section 8.1). For example, if the alarmsystem is armed and a zone with a motion detector opens, thecontrol panel will dial the telephone number in order to send theprogrammed event code to the central station computer. There is nodefault telephone number and you can enter any number from 0-9up to a maximum of 16 digits. If you would like to enter any specialkeys or functions, refer to table 3 below. If the telephone numbercontains less than 16 digits, press the [TRBL] key to indicate theend of the telephone number.[ENT] + [installer code] + [7] + [0] [4] + Telephone Number + [ENT]or [TRBL] if number <16 digits then [ENT].

&HQWUDO 6WDWLRQ 7HOHSKRQH 12 Streamline - Section 06 & 07 Î Hexa Programming - Addresses024-031The control panel can communicate with two central stationnumbers depending on the selected Reporting Options in section8.1. If the central station does not have a second number, enter thesame number as the first. There is no default telephone number andyou can enter any number from 0-9 up to a maximum of 16 digits. Ifyou would like to enter any special keys or functions, refer to table 3below. If the telephone number contains less than 16 digits, pressthe [TRBL] key to indicate the end of the telephone number.[ENT] + [installer code] + [7] + [0] [6] + Telephone Number + [ENT]or [TRBL] if number <16 digits then [ENT].

Caution: Both Central Station Telephone Numbers must beprogrammed in order for event reporting to function properly!

16 DE5281

Table 3 - Telephone # Special InstructionsEnter special instructions in the telephone numbers using thesekeys:

[BYPASS] = switch from pulse to tone while dialing[HOME] = * [MEM] = pause 4 seconds[AWAY] = # [TRBL] = end of telephone number

6\VWHP $FFRXQW &RGHVStreamline - Section 08 Î Hexa Programming - Addresses032-035All report codes are preceded by a 3 or 4-digit system account codeto ensure correct identification to the central station. For example, ifa zone opens, the control panel will first send the account codefollowed by the appropriate report code. In a partitioned system, thecontrol panel can send a separate account code for each system.This will identify to the central station from which system the reportcode originated. To do so, program a different number into eachaccount code. Where account code #1 will represent System “A”and account code #2 will represent System “B”.NOTE: If partitioning is disabled, program the same value forboth account numbers.There are no defaults and you can enter any hexa digit from 0 to F.The first 4 digits entered represent System Account Code #1. Thefinal 4 digits entered represent System Account Code #2. Pleasenote if required, system account codes can have 3 digits. To do so,press the [2nd] key followed by the 3-digit account number.[ENT] + [installer code] + [7] + [0] [8] + 4-digit Account Code #1 +4-digit Account Code #2 + [ENT]or[ENT] + [installer code] + [7] + [0] [8] + [2nd] + 3-digit AccountCode #1 + [2nd] 3-digit Account Code #2 + [ENT]

&RPPXQLFDWRU )RUPDWVStreamline - Section 09 Î Hexa Programming - Addresses 038Default: Ademco Slow for both numbersThe following option will determine which format the control panelwill use to communicate with the Central Station. Using table 4below, select the appropriate communication format for each CentralStation Telephone Number. The first digit will represent theCommunication Format for Central Station Telephone Number 1and the second digit will represent the Communication Format forCentral Station Telephone Number 2. Below you will find a briefdescription of all available Communicator Formats.[ENT] + [ INSTALLER CODE] + [0] [3] [8] + First digit = CentralStation Telephone #1 + Second digit = Central Station Telephone#2 + [ENT]

8.5.1 Ademco Contact ID (all codes)Table 5 - Contact ID Event Codes

System Event Event Code Contact ID Contact ID

Alarms / Restores 400 to 447 Burglary Zone # 130

Alarms / Restores on Zone 402, 426 Fire Alarm 110

Arm / Disarm 301 to 349 / Open / Close by user # 401

Zone Shutdown 448 to 471 Burglary Bypass # 573

Zone Tamper 472 to 495 Sensor Tamper 383

Zone Tamper Reset 510 Sensor Tamper 383

Auxiliary Power Trouble 496 & 504 System Trouble 300

Bell Disconnect / Max 497 & 505 Bell 1 Trouble 321

Low Battery 498 & 506 Low System Battery 302

AC fail 499 & 507 AC loss 301

Fire Loop Trouble 500 & 508 Fire Loop Trouble 373

Timer Loss / Timer 501 & 509 Time/Date Reset 625

TLM Trouble Restore 511 Telco 1 Fault 351

Test Report 512 Periodic Test 602

Panic #1 (1+3) 513 Panic Alarm 120

Panic #2 (4+6) 514 Medical 100

Panic #3 (7+9) 515 Fire Alarm 110

Duress 520 Duress 121

Late Close or No 516 & 517 Late to Open/Close 404

Partial Arming 518 Bypass 570

Recent Close 519 Open/Close 400

Program Change 525 Program Changed 306

Please note this format must use a 4-digit system account code(see section 8.4, System Account Codes). Ademco Contact ID is afast communicator format that uses tone dialing instead of pulsedialing. This communicator format also uses a pre-defined list ofindustry standard messages and event codes that should suit mostof your basic installation needs. The control panel will automaticallygenerate the Contact ID event codes for every event in addresses300 to 527 (see table 5). Therefore, you do not have to programaddresses 300 to 527.

8.5.2 Ademco Contact ID (programmable codes)Please note this format must use a 4-digit system account code(see System Account Codes, section 8.4). Ademco Contact ID is afast communicator format that uses tone dialing instead of pulsedialing. Use the Ademco Contact ID event list of industry standardmessages and event codes in the programming guide to programthe desired event codes into addresses 300 to 527.

8.5.3 Ademco ExpressThis high-speed reporting format communicates 2-digit (00 to FF)events programmed at addresses 300 to 527 at a speed of 2seconds per event. Unlike the other Ademco formats, the ContactID Event Codes are not used. Please note this format must use a4-digit system account code (see section 8.4)

8.5.4 DTMF – no handshakeThis format is the same as the Ademco contact ID (programmablecodes) except there is no verification of the report code sent (nohandshake). Use this format in reporting situations where a centralstation receiver is not connected to the telephone number. It is alsouseful for personal reporting where a "handshake" is not required.For example, in "double reporting" mode, the first central stationnumber can be connected to a receiver, while the second can beused for personal reporting using "no handshake" format. The panelwill make two attempts to call the "no handshake" number. Please notethis format must use a 4-digit system account code (see section 8.4).

8.5.5 Standard Pulse FormatsThe control panel supports the following pulse reporting formats(see table 4): Ademco slow, Silent Knight, Sescoa, and Radionics.

5HSRUWLQJ (YHQW &RGHVStreamline - Sections 11 to 67 Î Hexa Programming - Addresses300-527.An Event Code is a 2-digit hexadecimal value, consisting ofnumbers from 00-FF. Each address between 300 and 527represents a specific event, as described below and in the“Programming Guide”. When an event occurs in the system, thecontrol panel will send the 2-digit Event Code programmed at thecorresponding address to the central station. The method of EventCode transmission is dependent on the Communicator Formats(see section 8.5) and the Reporting Options (see section 8.1). Ifusing the Ademco Contact I.D. (all codes) format, you do not haveto program any addresses. If you plan to program most of the eventcode addresses, we suggest you use the Hexa StreamlinedProgramming Method as described in section 5.2. Otherwise, usethe Hexa Programming Method as described in section 5.1.

8.6.1 Arming CodesStreamline - Sections 11 to 23 Î Hexa Programming - Addresses300-349.

DE5281 17

Whenever the system is armed, the control panel will send theprogrammed event code to the Central Station identifying who orhow the system was armed.

8.6.2 Disarm ing CodesStreamline - Sections 23 to 35 Î Hexa Programming - Addresses350-399Whenever the system is disarmed, the control panel will send theprogrammed event code to the Central Station identifying whodisarmed the system. Also refer to section 8.12

8.6.3 Alarm CodesStreamline - Section 36 to 41 Î Hexa Programming - Addresses400-423Whenever a zone opens while the system is armed, the controlpanel will send the programmed event code to the Central Stationidentifying which zone generated an alarm.

8.6.4 Restore CodesStreamline - Sections 42 to 47 Î Hexa Programming - Addresses424-447The control panel will send the programmed event code to theCentral Station as soon as the zone closes after generating analarm or as soon as the zone closes after bell cut-off. For moreinformation, please see Report Zone Restore Options in section8.11.

8.6.5 Shutdown CodesStreamline - Sections 48 to 53 Î Hexa Programming - Addresses448-471If the Auto Zone Shutdown feature is enabled (see section 7.11),the control panel will send the programmed event code to theCentral Station identifying which zones were shutdown.

8.6.6 Tamper/Trouble CodesStreamline - Sections 54 to 59 Î Hexa Programming - Addresses472-495If the Tamper/Wire Fault Recognition Options are disabled (seesection 11.7), the control panel will never transmit these eventcodes. Otherwise, whenever a tamper occurs on a zone, the controlpanel will send the programmed Event Code to the Central Stationwhere Tamper 1 to Tamper 4 represent tamper report codes forcontrol panel inputs 1 through 4. With Advanced Technology Zoning(ATZ) enabled (see section 7.2) each Tamper Code address willrepresent two zones (as shown below). The control panel will sendthe programmed Event Code when a tamper occurs on either zone.

472 – Tamper 1 = Input 1 / Zones 1 & 2474 – Tamper 2 = Input 2 / Zones 3 & 4476 – Tamper 3 = Input 3 / Zones 5 & 6478 – Tamper 4 = Input 4 / Zones 7 & 8

8.6.7 Trouble/ Restore CodesStreamline or Hexa Programming Î Section 60 to 63 - Addresses496-511Each of the addresses represents a specific trouble condition. Thecontrol panel will report the appropriate event code to the centralstation when one of the following conditions occurs or after thecondition has returned to normal.

496 - Max. Auxiliary Current: is ≥ 1A.

504 - Max. Auxiliary Current Restore

497 - Bell Disconnect/Max. Bell Current: Bell is disconnected or bellcurrent is ≥ 3A.505 - Bell Disconnect Restore: No restore code for bell current

498 - Battery Disconnect/Low Voltage: Battery disconnected or batteryvoltage ≤ 10.5V.506 - Battery Disconnect/Low Voltage Restore

499 - Power Failure: Voltage on AC input is ≤ 12.5V. (Also refer tosection 8.9)507 - Power Failure Restore500 - Fire Loop Trouble: A tamper occurs on a fire zone (Zone3/24hr.).508 - Fire Loop Trouble Restore

501 - Timer Loss: The control panel detects a loss in the paneltimer.509 - Timer Programmed

502 to 503 - Reserved for Future Use

510 - All Tamper/Trouble Codes (see section 8.6.6) have returnedto "normal".511 - TLM Trouble Restore: Telephone line has restored after theTLM (see section 11.1) has detected the loss of a telephone line.

8.6.8 Special CodesStreamline or Hexa Programming Î Section 64 to 67 - Addresses512-527Each of the addresses represents a special condition in the system.When one of these special conditions occur, the control panel willreport the event code associated with the address. 512 – Test Report: The test report has been activated eithermanually (see section 8.8, Manual Test Report or automatically (seesection 8.7, Auto Test Report).513 – Panic 1: A User presses keys [1] and [3] to activate a Panic 1alarm514 – Panic 2: A User presses keys [4] and [6] to activate a Panic 2alarm515 – Panic 3: A User presses keys [7] and [9] to activate a Panic 3alarm.For more information on Keypad Panic Options see section 9.4.516 – Late To Close: “Timed” Auto Arming is enabled (seesection 9.1) and the system has not automatically armed itself at thespecified time.517 – No Movement: “No Movement” Auto Arming is enabled(see section 9.2) and no movement has occurred for the designatedamount of time.518 – Partial Arming: Whenever the system is “Away” armed,“Home” armed, or armed while one or more zones are bypassed.519 – Recent Close: An alarm occurs shortly after the system hasbeen armed (see section 8.10, Recent Close Delay).520 – Duress: The Duress feature is enabled (see section 4.4) anda User disarms the system using the User Code #48.521 to 523 – Reserved for Future Use525 – Program Change: The installer code is used to enter theprogramming mode.526 to 527 – Reserved for Future Use

$XWR 7HVW 5HSRUWDecimal Programming Î Addresses 046-048Default: Auto Test Report DisabledThe report code programmed at address 512 will be reported to thecentral station after the number of days programmed at address046 have elapsed and at the time programmed at address 047(hours) and 048 (minutes). To disable this feature, program 000 ataddress 046. Also note that if [2nd][2nd] is programmed at address512 nothing will be reported.[ENT] + [installer code] + [0] [4] [6] + 2 digits (days) + [0] [4] [7] + 2digits (hours) + [0] [4] [8] + 2 digits (minutes) + [ENT]

0DQXDO 7HVW 5HSRUWKey Access Programming Î key [BYPASS]Activating the manual test report will send the Event Codeprogrammed at address 512 to the Central Station.[ENT] + [Installer, Master, or User 1 Code] + [BYPASS]

3RZHU )DLOXUH 5HSRUW 'HOD\Decimal Programming Î Addresses 054Default: 30 minutesAfter a power failure, the control panel will delay transmission of theevent code programmed at address 499 by the period programmedat this address (001 to 255 minutes).[ENT] + [installer code]+ [0] [5] [4] + 3-digit decimal value (001-255)+ [ENT]

18 DE5281

5HFHQW &ORVH 'HOD\Decimal Programming Î Addresses 060Default: DisabledThe system will transmit the recent close event code programmedat address 519 if after arming the system, an alarm occurs withinthe period programmed at this address (001 to 255 minutes).Program 000 into address 060 to disable this feature.[ENT] + [installer code] + [0] [6] [0] + 3-digit decimal value(001-255) + [ENT]8.11 Report Zone Restore OptionsFeature Select Programming Î Address 088; key [bypass]Default: Zone Restore Codes Transmit on Bell Cut-OffWith the “Bypass” indicator off, the report codes programmed ataddresses 424-447 (see Restore Codes in section 8.6.4) will onlytransmit if the zone has returned to normal upon bell cut-off (seesection 9.11). With the “bypass” indicator on, the codes will

transmit as soon as the zone returns to normal (zone closure).LED “bypass” off: Report Zone Restore on Bell Cut-OffLED “bypass” off: Report Zone Restore on Zone Closure[ENT] + [installer code] + [0] [8] [8] + “bypass” On/Off + [ENT]

5HSRUW &RGH 'LVDUPLQJ 2SWLRQVFeature Select Programming Î Address 088; key [TRBL]Default: Disarming Codes Transmit on User DisarmingWith the “TRBL” indicator off, the report codes programmed ataddresses 350-399 (see Disarming Codes in section 8.6.2) willtransmit whenever a User disarms the system. With the “TRBL”indicator on, the control panel will transmit these codes when a Userdisarms a system in alarm.LED “TRBL” off: Always Report DisarmLED “TRBL” on: Report Disarm only after alarm[ENT] + [installer code] + [0] [8] [8] + “TRBL” On/Off + [ENT]

$50 $50',6$50 $/$50 237,216',6$50 $/$50 237,216

´7LPHGµ $XWR $UPLQJFeature Select Programming Î Address 086, key [5]Default: DisabledThe alarm system will automatically arm itself at a specified timeeveryday. Note, as with regular arming, the system will not arm if azone is open and will report a “late to close” to the central station. Ifthis occurs, the system will not arm until the next day. The type ofarming is dependent on the Auto Arming Options (see below).Program the Auto Arm Time as described below.

9.1.1 Auto Arm TimeThe control panel will automatically arm itself at the specified time if “Timed” Auto Arming (see above) is enabled. The time isprogrammed using the 24-hour clock (i.e. 8:00PM = 20:00). Thereare two methods of programming the “Auto Arm Time” as describedbelow.

• Decimal Programming Î Address 044 & 045 Program the “Auto Arm Time” in hours into address 044 and the

“Auto Arm Time” in minutes into address 045.[ENT] + [installer code] + [0] [4] [4] + 3-digit decimal value(hours) + [0] [4] [5] + 3-digit decimal value (minutes) + [ENT]

• Key Access Programming Î key [9] The User 1, Master, or Installer can program the “Auto Arm Time” using

this method.[ENT] + [Installer, Master, or User 1 Code] + [9] + 2 digitsrepresenting hours + 2 digits representing minutes + [ENT]

9.1.2 Auto Arming OptionsFeature Select Programming Î Address 090, key [2]Default: Regular ArmingThe “Auto Arm” feature will arm the system as described in thetable below.[ENT] + [installer code] + [0] [9] [0] + “2” On/Off + [ENT]

LED “2” Partitioning Option

Off Off “Regular Arming”

Off On “System A and B Arming”

On Off “Home Arming”

On On “System A Arming” Figure 28 - Arming/Di sarm ing Related Features

Auto Arm Time

Addresses 044 & 045

(sec. 9.1.1)

Timed Auto Arming

Addresse 086; [5]

(sec. 9.1)

Auto Arming Options

Address 090 [2]

(sec. 9.1.2) No Movement Auto

ArmingAddress 086; [6]

(sec. 9.2) No Movement TimeAddress 055(Sec. 9.2.1)

System “A”/HomeArm Priority

Addresses 062, 064& 066; all keys

Code Priority Definewhich users can

System “A”/HomeArm, arm System “B”

or Bypass Zones

(sec. 9.12)

System “B” ArmPriority

Addresses 068, 070& 072; all keys

Bypass AccessAddresses 074, 076

& 078; all keys

“One-Key” RegularArming

Address 088; [7](sec. 9.3)

“One-Key” System“A”/Home ArmingAddress 088; [8]

(sec. 9.4)

Keyswitch ArmingAddress 086;

[2] & [3] (sec. 9.5)

Bell SquawkAddress 086; [MEM]

(sec. 9.6)

“Beep” on Exit DelayAddress 088;

[AWAY](sec. 9.8)

Exit DelayAddress 049

(sec. 9.7)

Alarm TransmissionDelay

Address 059(sec. 9.9)

Bell Cut-Off TimeAddress 052(sec. 9.11)

Arm/DisarmRelatedFeatures

DE5281 19

´1R 0RYHPHQWµ $XWR $UPLQJFeature Select Programming Î Address 086, key [6]Default: DisabledIf the control panel does not detect any zone openings for aspecified period, the control panel will arm the system and transmitthe event code programmed at address 517. Note the type ofarming is dependent on the Auto Arming Options (seeabove). Program the “No Movement” Auto Arm as described below.LED “6“ off: No Movement Auto Arm DisabledLED “6” on: No Movement Auto Arm Enabled[ENT] + [installer code] + [0] [8] [6] + “6” On/Off + [ENT]

9.2.1 “No Movement” Auto Arm TimeDecimal Programming → Address 055Default: 8 hours000 = disabled; (001-255) X 15 minutesIf the “No Movement” Auto Arming (see above) feature is disabledand a time is programmed, the control panel will transmit the eventcode programmed at address 517 if no movement is detectedduring the programmed period.[ENT] + [INSTALLER CODE] + [0] [5] [5] + 3-digit decimal value(001-255) + [ENT]

´2QH.H\µ 5HJXODU $UPLQJFeature Select Programming → Address 088, key [7].Default: Disabled.A user can “regular” arm the system by pressing and holding the[QUICK] key for 2 seconds.LED “7” off: “One-Key” Regular Arming DisabledLED “7” on: “One-Key” Regular Arming Enabled[ENT] + [INSTALLER CODE] + [0] [8] [8] + “7” On/Off + [ENT]

´2QH.H\µ +RPH µ6\VWHP $µ

$UPLQJFeature Select Programming → Address 088, key [8].Default: Disabled.Press and hold the [HOME] key for 2 seconds to “Home” arm thesystem if partitioning is disabled. If the system is partitioned, thecontrol panel will arm “System A”.LED “8” off: “One-Key” Home/“System A” Arming DisabledLED “8” on: “One-Key” Home/“System A” Arming Enabled[ENT] + [INSTALLER CODE] + [0] [8] [8] + “8” On/Off + [ENT]

$UPLQJ 8VLQJ .H\VZLWFK RU

3XVKEXWWRQFeature Select Programming → Address 086, key [2] & [3].Default: Disabled.The user can use a keyswitch or pushbutton to “Home” and“Regular” arm/disarm the system. Refer to sections 3.7 & 12.8.[ENT] + [INSTALLER CODE] + [0] [8] [6] + “2” & “3” On/Off +[ENT]

Table 6 - Keyswitch Arming Table

LED “2” LED “3” FunctionOff Off Disabled

On Off Disabled

Off On “Regular” Arm

On On “Home” Arm

%HOO 6TXDZNFeature Select Programming Î Address 086; key [MEM]Default: DisabledWith this feature enabled, the bell or siren will sound a half-second“squawk” upon arming and two half-second “squawks” upondisarming.LED “MEM” off: Bell Squawk DisabledLED “MEM” on: Bell Squawk Enabled[ENT] + [INSTALLER CODE] + [0] [8] [6] + “MEM” On/Off + [ENT]

([LW 'HOD\Decimal Programming Î Address 049Default: 60 secondsThe Exit Delay applies to all zones. This option determines howmuch time the user has to leave the protected area before thesystem arms after entering a valid access code. You can programthe Exit Delay from 001 to 255 seconds.[ENT] + [installer code] + [0] [4] [9] + 3 digit decimal value (001-255)+ [ENT]

%HHS RQ ([LW 'HOD\Feature Select Programming Î Address 088, key [away]Default: DisabledWith this feature enabled, the keypad will sound an intermittent“beep” during exit delay (except when in “HOME” arming).Frequency of intermittent beeps increases during the last 10seconds of the exit delay period.LED “AWAY” off: Beep on Exit Delay DisabledLED “AWAY” on: Beep on Exit Delay Enabled[ENT] + [installer code] + [0] [8] [8] + “AWAY” On/Off + [ENT]

$ODUP 7UDQVPLVVLRQ 'HOD\Decimal Programming Î Address 059This time limit, set between 5 and 63 seconds, is the delay periodthe control panel will wait before reporting an alarm to the centralstation. During this period, disarming the system will cancel allpending alarms and send the restore codes. Programming 000-004disables this feature.[ENT] + [INSTALLER CODE] + [0] [5] [9] + 3-digit decimal value(005-063) + [ENT]

6LOHQW =RQHV 6LOHQW 3DQLFV

2SWLRQFeature Select Programming Î Address 086, key [9]If the “9” indicator is on, silent zones or silent panics only transmit areport to the central station. The system will not indicate an alarmand will not have to be disarmed, nor will the control panel activatethe PGM. If a keypad panic has been defined as audible, the controlpanel will override this option.LED “9” off: Silent Zones & Silent Panics generate a silent alarmLED “9” on: Silent Zones & Silent Panics generate a report only[ENT] + [installer code] + [0] [8] [6] + “9” On/Off + [ENT]

%HOO &XW2II 7LPHDecimal Programming Î Address 052Default: 5 minutesAfter an audible alarm, the bell or siren will stop after theprogrammed time has elapsed.[ENT] + [installer code] + [0] [5] [2] + 3-digit decimal value(001-255) minutes + [ENT]

&RGH 3ULRULW\Feature Select Programming Î Address 062-078, [all] keysIn order for a user to arm a partitioned system, to “Home” arm,“Away” arm or to manually bypass zones, the user must be givencode priority. Using the “Feature Select Programming Method”,identify which arming methods each can use. Users not given codepriority can only “regular” arm a non-partitioned system. For moreinformation on arming/disarming methods please refer to section 12,User/Keypad Functions. • Partitioning Disabled:

Addresses 062-066: Lit LEDs denote which user codes canactivate "Home" arming.

Addresses 068-072: Lit LEDs denote which user codes canactivate "Away” arming.

Addresses 074-078: Lit LEDs denote which user codes can"Bypass" zones.

20 DE5281

• Partitioning Enabled:Addresses 062-066: Lit LEDs denote which user codes canarm “System A".Addresses 068-072: Lit LEDs denote which user codes canarm “System B".Addresses 074-078: Lit LEDs denote which user codes can"bypass" zones.

3*0 SURJUDPPDEOH RXWSXWV 3*0 SURJUDPPDEOH RXWSXWV

3*0 7\SHVStreamline - Sections 09 Î Hexa Programming - Address 039The MAESTRO control panels have one programmable output(PGM). When a PGM closes, ground is supplied to activate anydevice or relay connected to it, providing up to a maximum of 50mA.When a PGM opens, the circuit is opened from ground, thereforenot providing any power to devices connected to it. To program aPGM you must define the PGM state (normally open or normallyclosed), the timing (regular or timed) and you must define the typeof logic (“OR”, “AND”, “EQUAL”). To do so, use table 7 to determinewhich hexa digit to program into address 039, where the first hexadigit programmed corresponds to the PGM.

• Regular N.O./N.C. A triggered PGM will switch to its opposite state (i.e. closed to

open or opened to closed). The PGM will return to its originalstate once the event(s) that triggered it have terminated.

• Timed N.O./N.C A triggered PGM will switch to its opposite state (i.e. closed to

open or opened to closed). The PGM will remain in itsopposite state for the period programmed at address 056. See“PGM Timer Setting” in section 10.2 for details. If the PGM istriggered again before the period has elapsed, the PGM willremain in its opposite state and the timer will be reset.

• “OR” Logic Will trigger a PGM when at least one event occurs from a

specific group of events (e.g. key [1] and/or [2] is pressed onthe keypad).

• “AND” Logic The “AND” logic will trigger a PGM when all events, or more,

occur from a specific group of events (e.g. Keys [1] and [2] arepressed simultaneously. Note that pressing those two keys inconjunction with any other key will also trigger the PGM).

• “EQUAL” LogicThe “EQUAL” logic will trigger a PGM only when the eventsfrom a specific group of events occur (e.g. Keys [1] and [2] arepressed). Note the PGM will only trigger when pressing keys[1] and [2] simultaneously, if any other key is pressed at thesame time (e.g. [1], [2] & [3]) the PGM will not trigger.

[ENT] + [INSTALLER CODE] + [0] [3] [9] + one digit from table 7 +[2ND] + [ENT]

3*0 7LPHU 6HWWLQJDecimal Programming Î Address 056Default: 5 secondsYou can program the PGM Timer from 1 to 127 seconds or 1 to 127minutes. To determine the 3-digit decimal value, do the following:

• To program in seconds, the required time is respective to thedecimal value1 second = 001, 55 seconds = 055, 127 seconds = 127.

• To program in minutes, add the desired minutes to 128:5 minutes: 128 + 5 = 133127 minutes: 128 +127 = 255

[ENT] + [ INSTALLER CODE] + [0] [5] [6] + 3-digit decimal value(001-255) + [ENT]

DE5281 21

3*0 2SWLRQVStreamline or Hexa Programming Î Section 10 - Addresses 040 &042

The PGM options define which sequence of events will trigger thePGM. The PGM options are virtually endless, therefore, to list themin the manual is impractical. Table 8, contains a list of the mostcommonly used PGM options with the required 2-digit data for eachaddress.

27+(5 237,216 27+(5 237,216

7HOHSKRQH /LQH 0RQLWRULQJ 7/0Feature Select Programming Î Address 086, key [2ND] & [1]Default: TLM DisabledWhen enabled, the system verifies the existence of a telephone lineevery 4 seconds. After each successful test, the dialer LED (greenlight) on the control panel flashes briefly. If the test fails the ledflashes on and off until the control panel detects the telephone lineagain. TLM will activate a trouble when less than 3 volts is detectedin four consecutive tests. Note, when the dialer detects a telephonering, the TLM test stops for 1 minute.There are three TLM options, which are set as indicated in tablenumber 9: 1 . OFF/ON: Line test failure will generate a trouble indication; “10”

indicator will illuminate on the keypad. 2 . ON/OFF: Line test failure will generate a trouble indication and

an alarm if the system is armed. 3 . ON/ON: Line test failure will generate a trouble indication and

cause a silent zone or a silent panic alarm to switch to audiblemode.

[ENT] + [ INSTALLER CODE]+ [0] [8] [6] + “2 ND" & “1” On/Off +[ENT]

'LDOLQJ 2SWLRQVFeature Select Programming Î Address 086, key [7]Default: Pulse DialingYou can program the control panel to use the pulse dialing ortone/DTMF dialing format.LED “7” off: Pulse DialingLED “7“ on: Tone/DTMF Dialing[ENT] + [INSTALLER CODE] + [0] [8] [6] + “7” On/Off + [ENT]

'LDOLQJ 3XOVH 5DWHVFeature Select Programming Î Address 086, key [0]Default: Pulse USA 1:1.5This selection reflects the ratio between “pulse” time and "quiet"time. Select Pulse Europe for a 1:2 ratio and select Pulse USA for1:1.5.LED “10” off: Pulse Europe 1:2LED “10” on: Pulse USA 1:1.5[ENT] + [INSTALLER CODE] + [0] [8] [6] + “10” On/Off + [ENT]

.H\SDG 3DQLF 2SWLRQVFeature Select Programming Address 088 keys [1] to [6]This feature will generate an alarm when the User presses twospecific keys on the keypad simultaneously for 2 seconds asdescribed below:LED “1” on = Panic 1 (keys [1] and [3]) enabledLED “2” on = Panic 2 (keys [4] and [6]) enabled

LED “3” on = Panic 3 (keys [7] and [9]) enabledKeypad panic options:LED “4” off = Panic 1 silentLED “4” on = Panic 1 audibleLED “5” off = Panic 2 silentLED “5” on = Panic 2 audibleLED “6” off = Panic 3 silentLED “6” on = Panic 3 fire alarmSilent operation:When using the panic keys, the control panel will sound a singleconfirmation beep. The control panel will transmit the event codesprogrammed at addresses 513, 514, and 515. The alarm will latch(no audible alarm) and the "armed" light on the keypad will flash untilthe system is disarmed by a valid User code.Audible operation:Same as silent operation, except the alarm output (bell/siren) willactivate until the system is disarmed by a valid User code or untilthe Bell Cut-Off Time (see section 9.11) elapses.Fire operation:Same as audible operation except that bell/siren output will bepulsed (intermittent "on"/"off").

3DQHO 7LPHKey Access Programming Î key [MEM]To program the current time into the control panel press:[ENT] + [Installer, Master, or User 1 Code] + [MEM] + 2 digitsrepresenting hours (00-23) + 2 digits representing minutes (00-59)

7LPH &RUUHFWLRQStreamline - Section 09 Î Hexa Programming - Address 037If you notice a gain or loss in the control panel time, calculate theaverage gain or loss per day and select the “opposite” amount fromthe Time Correction table in order to automatically correct the timesetting every 24 hours.Example: The control panel loses 4 minutes per month,representing an average loss of 8 seconds per day. Therefore,program [2] (plus 8 seconds) as the second digit in address 037 tocompensate for the 8-second loss.

Table 2 - Answering Machine Override Options[2nd] or [1] = Answering Machine Override disabled[2] = 16 sec. [4] = 32 sec. [6] = 48 sec. [8] to [TRBL] = 60 sec.[3] = 24 sec. [5] = 40 sec. [7] = 56 sec.

Table 10 - Time Correction

(address 037 second digit)

[2nd] - No adjustment [8] - Minus 4 seconds

[1] - Plus 4 seconds [9] - Minus 8 seconds

[2] - Plus 8 seconds [0] - Minus 12 seconds

[3] - Plus 12 seconds [HOME] - Minus 16 seconds

[4] - Plus 16 seconds [AWAY] - Minus 20 seconds

[5] - Plus 20 seconds [BYPASS] - Minus 24 seconds

[6] - Plus 24 seconds [MEM] - Minus 28 seconds

[7] - Plus 28 seconds [TRBL] - Minus 32 seconds

7DPSHU:LUH )DXOW 5HFRJQLWLRQ

2SWLRQVFeature Select Programming Î Address 088, keys [0] and [HOME]When the control panel detects an open or a short on a zone, it willreport this in the following manner. When the system is armed ,regardless of the tamper/wire settings it will always generate an

22 DE5281

alarm and trouble indicator (LED “9” ). Alarms will be audible orsilent depending on individual zone definitions. If an open or shortoccurs on a disarmed system, the control panel will generate anincident depending on the following settings:

“10” “HOME” Tamper Recognition Option

OFF OFF Tamper/Wire Fault Disabled

OFF ON Trouble Enabled

ON OFF Silent Alarm Enabled

ON ON Audible Alarm Enabled

Tamper/Wire Fault Disabled:Tamper/wiring failure recognition is disabled.Trouble Enabled:Tamper/wiring failure will generate a trouble indicator (LED “9”) anda trouble report code (see Tamper/Trouble Codes , in section 8.6.6)when the system is disarmed.Silent Alarm Enabled Tamper/wiring failure will generate a trouble indicator (LED “9”), atrouble report code (see Tamper/Trouble Codes, in section 8.6.6 )and a silent alarm (no bells/sirens)Audible Alarm Enabled:Tamper/wiring failure will generate a trouble indicator (LED “9”), atrouble report code (see Tamper/Trouble Codes , in section 8.6.6)and an audible alarm.NOTE: When the zone definition is "24 hour", the tamper definitionfollows the audible/silent alarm definition of the "24 hour" zone.

7DPSHU %\SDVV 2SWLRQVFeature Select Programming Î Address 090, key [6]With this option enabled (LED “6” on), the control panel will notgenerate an alarm if a tamper is detected on a bypassed zone whilethe system is armed. With the option disabled, the control panel willgenerate an alarm if a tamper or wire fault is detected on bypassedzone when the system is armed.LED “6“ off: Alarm if Tamper on Bypassed ZoneLED “6” on: No Alarm if Tamper on Bypassed Zone[ENT] + [INSTALLER CODE] + [0] [9] [0] + “6” On/Off + [ENT]

,QVWDOOHU 7HVW 0RGHKey Access Programming Î key [8]The “Installer Test Mode” will allow you to perform walk tests wherethe bell or siren will squawk to indicate opened zones. To enter orexit the control panel “Test Mode” press:[ENT] + [INSTALLER CODE] + [8] to enable; press [8] again to disable

([FOXGH 3RZHU )DLOXUH )URP

7URXEOH 'LVSOD\Feature Select Programming Î Address 090, key [2nd]Default: disabledExcludes the Power Failure, LED “2”, from the Trouble Display (seesection 12.12.2).

$XGLEOH 7URXEOH :DUQLQJFeature Select Programming Address 090, key [9]Default: DisabledTrouble conditions will sound an intermittent “beep” on the keypad.To silence the trouble warning, press the [TRBL] key.

3RZHU 'RZQ 5HVHWPerforming a power down reset will set the installer and mastercodes to factory default. Values entered at addresses 008-043,062-126, 300-527, as well as all the user codes, will be erased([2ND], [2ND]). Programmed values of all other addresses do notchange. Note to perform a reset the installer lock must be disabled.To perform a power down reset perform the following: 1 . Make sure the installer lock is disabled (see section 4.5) 2 . Remove the battery and AC power from the control panel. 3 . Set the “reset” jumper to on. Place a jumper on the “reset” pins

of the control panel. 4 . Re-connect the AC power and the battery to the control panel. 5 . Wait 10 seconds and remove the jumper.

86(5 86(5.(<3$' )81&7,216.(<3$' )81&7,216

The innovative Maestro keypad takes a new approach to securityfeatures and functions. Each LED indicator from 1 to 10 on thekeypad, respectively, represents each zone on the control panel.When zone indicator is “off”, the status in the protected zone isnormal. If the zone indicator is “on”, this means the zone is open.The green “READY” indicator on the keypad will illuminate when thestatus of all the zones is normal (zones are closed). Therefore, allwindows and doors must be closed and motion detectors must notdetect any movement except those zones that have been bypassed.Confirmation Beep: an intermittent series of beeps(“beep-beep-beep”) indicating a successful keypad entry or systemoperation.End/Rejection Beep: one long tone (“beeeeeeep”) indicatingincorrect keypad entry or unsuccessful system operation.

3URJUDPPLQJ 0DVWHU 8VHU

&RGHVThe Maestro control panels have one Master (00) code and up to 48User (01-48) codes. The default Master code is 0000. The Mastercode can arm the system using any arming method, cancreate/modify user codes and can perform Key AccessProgramming (see section 12.13). The User 1 code cancreate/modify access codes and perform key access programming.The access code consists of either 4 or 6-digits and each digit canbe any value from 0 to 9. Note, do not enter [2nd] whenprogramming the master code as this will invalidate the mastercode.[ENT] + [Master or User 1 Code] + 2-digit code number (00-48) + 4or 6-digit access code + [ENT]

5HJXODU $UPLQJ “READY” indicator on + [valid access code]This method, commonly used for day-to-day arming, will arm all thezones in the system. To do so, the keypad’s green “READY” lightmust be illuminated, indicating that all zones are closed. All doorsand windows must be closed, and there can be no movement inareas monitored by motion detectors. Once the “READY” light is on,a valid user access code must be entered. If a mistake is madeentering the code or if the “READY” indicator is not on when thecode was entered, the keypad will sound a “rejection beep”(beeeeeeeep).When the correct user access code is entered, the keypad willsound a “confirmation beep” (beep-beep-beep) and the red "arm"indicator will illuminate. The “READY” light will flash and the keypadwill "beep" during the exit delay period (see section9.7). During thefinal 10 seconds of the exit delay, the keypad will “beep” and the“READY” indicator will flash at a faster rate. At the end of the exitdelay, the keypad will sound a “confirmation beep”, the green“READY” indicator will extinguish and the red “ ARM” indicator willremain illuminated to indicate that the system is armed.

12.2.1 “One-Key” Re gular Arming“ready” indicator on + hold the [quick] key for 2 secondsTo use this feature, enable the “One-Key” Regular Arming option(see section “One-Key” Regular Arming). When the green "ready"light is on, pressing and holding the [quick] key for 2 seconds willarm all zones in the system. This feature can be used to allowspecific individuals like service personnel (i.e. cleaners,maintenance) to arm the system when leaving the protected area,without giving them access to any other control panel operations.

DE5281 23

The use of a valid access code is still required to disarm thesystem. For details on “Regular Arming”, refer to section 12.2.

$ZD\ $UPLQJ[away] + [valid access code]To rapidly arm the system without having to wait for the green“ready” indicator, simply press the [away] key followed by a validaccess code. Once the exit delay expires, any open zones will beconsidered “deactivated” by the control panel. Therefore, thesezones will not generate an alarm. If during this period a “deactivated”zone is closed, the control panel will revert that zone to “active”status, hence, will generate an alarm if breached.If a mistake is made entering the code, the keypad will sound a“rejection beep” (beeeeeeeep). When the correct user code isentered, the keypad will sound a “confirmation beep”(beep-beep-beep) and the red "arm" indicator will illuminate. The"ready" light will flash and the keypad will "beep" during the exitdelay period (see section 9.8). During the final 10 seconds of theexit delay, the keypad will “beep” and the “ READY” indicator willflash at a faster rate. At the end of the exit delay, the green“ READY” indicator will stop flashing and the red “ ARM” indicator willremain illuminated. If programmed at address 518, the control panelwill send a “partial arm” report code to the central station. Note, touse this method the user must have “AWAY” arming priority, seeCode Priority in section 9.12.

+RPH $UPLQJ[home] + [valid access code]“Home” arming allows the user to remain in the protected area whilepartially arming the system. This means that they can stay in andmove around the establishment, while certain designated zones arearmed. For example, entry/exit points like doors or windows, thebasement, or perhaps all the zones on the perimeter of theestablishment may be armed when going to sleep at night, while theother zones remain deactivated. To program which zones will beactivated when “home arming” the system refer to “SystemA”/Home Zones in section 7.10.1. Also note that fire zones must beprogrammed as “home zones”; they can not be bypassed.Unlike regular arming, the green “ READY” indicator does not have tobe illuminated. Only doors and windows programmed as “homezones” must be closed, and there can be no movement in areasmonitored by motion detectors in “home zones”. To “HOME” armthe system, press the [home] key followed by a valid access code. Ifa mistake is made entering the code or if a “home zone” is openwhen entering the code, the keypad will sound a “rejection beep”(beeeeeeeep). After entering the correct user access code, thekeypad will sound a “confirmation beep” (beep-beep-beep), the red“HOME” and "arm" indicators will illuminate and the green "ready"indicator will flash during the exit delay period. During the final 10seconds of the exit delay, the “ready” indicator will flash at a fasterrate. At the end of the exit delay, the keypad will sound a“confirmation beep”, the “ready” indicator will stop flashing and thered “HOME” and “arm” indicators will remain illuminated. Note, touse this method the user must be given “HOME” arming priority,see Code Priority in section 9.12.

12.4.1 “One-Key” Home Arminghold the [home] key for 2 secondsTo use this feature, enable the “One-Key” Home/System Armingoption (see section “One-Key” Home/System Arming). When all“homes zones” are closed, pressing and holding the [home] key for2 seconds will arm only zones programmed as “home zones”. Fordetails on “Home Arming”, refer to section 12.4.

12.4.2 “One-Key” D ouble Home ArmingAfter having “HOME” armed the system (see section 12.4), pressand hold the [home] key for 2 seconds during the exit delay, untilyou hear a single “beep”. This will switch all “entry delay” zones to“instant” zones (see section 7.6). Therefore, any entry delay zonethat is breached will immediately generate an alarm instead ofwaiting a pre-determined period.

12.4.3 Fast ExitThis feature is only available when the system is “Home” armed(see section 12.4). This feature will allow you to exit the already

armed premises and keep the system armed.This can be done one of two ways: • With the system already “HOME” armed, press and hold the

[HOME] key for 2 seconds. The system will switch to exit delaymode (green “ READY” indicator flashes). At the end of the exitdelay period, the system will return to “HOME” arm mode.

• With the system already “HOME” armed, press and hold the[QUICK] key for 2 seconds. The system will switch to exit delaymode (green “ READY” indicator flashes). At the end of the exitdelay period, the system will “regular” arm the system (seesection 12.2).

$UPLQJ'LVDUPLQJ 3DUWLWLRQV • Thanks to Maestro’s partitioning feature, two distinct systems

(A and B) can be created and controlled by the control panel.Partitioning can be used in installations where shared securitysystems are more practical, such as office/warehouse buildings,or apartment/condominium complexes. Each zone can beassigned to System A, System B, both systems or given nosystem assignment. User access codes can also beprogrammed to arm/disarm one system or both systemssimultaneously (see Code Priority in section 9.12). Unlikeregular arming, the green “ready” indicator does not have to beilluminated. All doors and windows pertaining to the desiredsystem must be closed, and there can be no movement in areasmonitored by motion detectors in the desired system.

1 . If a user is not given any code priorities, the user will never beable to arm or disarm the system when partitioned.

2 . If a user is given code priority to one of the two systems,entering the correct access code will arm or disarm thesystem to which the user was given priority.

3 . If a user is given code priority to arm/disarm both systems A & B,it will function as follows: • If the User enters the correct access code when

systems "A" and "B" are disarmed, it will completely armboth systems.

• If the User enters the correct access code whensystems "A" and "B" are armed, it will completely disarmboth systems.

• When the system is partially armed, (i.e. only System "A"or only System "B" is armed) entering the correct accesscode will arm the other system.

• To arm/disarm each system separately, do the following: • Press [HOME] + [VALID ACCESS CODE] to arm/disarm

"System A". • Press [AWAY] + [VALID ACCESS CODE] to arm/disarm

"System B".If a mistake is made entering the code or if a zone in the desiredsystem is open when entering the code, the keypad will sound a“rejection beep” (beeeeeeeep). When the access code is correctlyentered, the keypad will sound a “confirmation beep”(beep-beep-beep). The keypad can display the status of bothsystems. When “System A” is armed, the red “HOME” and “arm”indicators will remain on. If System B is armed, the red “AWAY” and“arm” indicators will remain on. When both systems are armed, allthree lights will remain on.

12.5.1 One-Key “System A” ArmingThis feature allows the user to arm “System A” without the use of anaccess code. To use this feature, enable the “One-Key”Home/”System A” option (see section“ One-Key” Home/”SystemA”). When all the zones in “System A” are closed, press and holdthe [home] key for 2 seconds to arm “System A”. This feature canbe used to allow specific individuals like service personnel (i.e.cleaners, maintenance) to arm the system when leaving theprotected area, without giving them access to any other controlpanel operations. For “System A” Arming details refer to sec. 12.5.

6\VWHP 'LVDUPLQJThe user must enter the protected area through a designatedentry/exit point. The keypad will "beep" during the entry delayreminding the user to disarm the system. Upon entry of a validaccess code, the red "arm" indicator will extinguish and the keypad

24 DE5281

will sound a confirmation "beep" (beep-beep-beep) denoting thesystem has been disarmed. If an incorrect access code is entered,the keypad will sound a rejection "beep" (beeeeeeeep). Press the[CLR] key at any time to clear data and re-enter another accesscode. If an alarm was generated from a fire or 24-hour zone whilethe system was armed, entering a valid user code will silence thesiren. However, you should then check the zone and eliminate thecause of the alarm. 24-hour zones that restore and re-alarm willcause another alarm 30 seconds after an access code is entered tosilence the alarm. If you are unable to pinpoint the reason for thealarm, call your installer.

$ODUP 0HPRU\If an alarm situation occurs when the system is armed, the “MEM”indicator on the keypad will illuminate. A record of all alarmsituations that occur is stored in memory. After disarming thesystem, pressing once on the [MEM] key will display which zoneswere open during the alarm period by illuminating the correspondingzone indicator(s). Please note that if the [MEM] key is pressedagain you will enter the event display which can not decoded. To exitalarm memory display, press the [CLR] key.

.H\VZLWFK RU 3XVKEXWWRQ $UPLQJ

'LVDUPLQJA keyswitch or push button can be used to “Home” (section 12.4) or“Regular” (section Regular Arming) arm/disarm the system. If thesystem is ready and the button is pressed, the system will arm.Pressing the button again will disarm the system. If a “Home” armedsystem is in entry delay or if an alarm has been generated while“Home” armed, the keyswitch or push button can not be used todisarm the system. In this case, only a keypad can disarm thesystem. In a partitioned system the keyswitch or push button willarm/disarm “System A” regardless of the “System B” status. Toenable this feature and set the options (home or regular arming)refer to Arming Using Keyswitch in section 9.5.

0DQXDO =RQH %\SDVVLQJ[bypass] + [valid access code] + [zones to bypass] + [ENT]When a zone is bypassed it will no longer be monitored by thecontrol panel, hence, will not generate an alarm. A user may wish tobypass certain zones when, for example, workers are renovatingpart of their establishment or if a component in their system isdamaged. Manual bypass arming instructs the control panel toignore (“deactivate”) specified zones in order to arm the remainderof the system. In order for a user to bypass any zones, verify thatthe following options are set in the control panel: • You must first define which zones are Bypass Enabled Zones

(see section 7.11). Zones not identified as Bypass Enabled cannot be bypassed.

• Only users with Code Priority (see section 9.12) can bypasszones.

• Please note, the control panel can not bypass fire zones.To bypass zones, press the [bypass] key followed by a valid accesscode. If the wrong code was entered or a code without bypasspriority, the keypad will sound a “rejection beep” (beeeeeeep). If thecorrect code is entered, the yellow “bypass” light will flash toindicate that you are now in “bypass mode”. If there are anycurrently bypassed zones, their respective zone indicators will turnon. Press the key corresponding to the zone you wish to bypassuntil their respective zone indicator turns on. For example, press the[1] key until the red “1” indicator turns on, indicating that zone 1 isbypassed. If the zone you wish to bypass has not beenprogrammed as “bypass enabled”, the corresponding zone indicatorwill never illuminate. Press the [CLR] key to erase the current zonebypass entries and exit the “bypass mode”. If you have entered thecorrect bypass entries, press the [ENT] key to accept these entries.The yellow “bypass” indicator will remain on, denoting that zones inthe system are currently bypassed, hence, the next time the systemis armed, certain zones will be bypassed.

%\SDVV 5HFDOOThis feature permits users to reinstate the last zone bypass entriessaved in memory. When the system is disarmed, the bypass entries

will be erased. By using the “bypass recall” feature, you canreinstate the previous bypass entries saved in memory. While in the“bypass mode”, press the [bypass] + [ENT] keys and the previousbypass status will be re-established. This eliminates the need tore-enter the bypass entries every time the system is armed. If auser is in the process of entering new bypass entries on thekeypad, pressing the [bypass] key will override new information andreinstate previous bypass entries.

.H\SDG &KLPH =RQHVA chimed zone "advises" you when a zone is opened by creating arapid intermittent beep tone (beep-beep-beep). Up to six zones plusthe local keypad zone can be programmed as chime zones. To turnon the "chime zone" feature, press and hold the key correspondingto the desired zone ([1] to [6]) for three seconds until the intermittentchime beep is heard. This means that the chime feature has beenactivated. If a continuous beep is heard, this means that the chimebeep has been deactivated. To enable the chime feature on thekeypad zone, press and hold the [8] key for three seconds. To mutethe keypad’s alarm sounder, press and hold the [9] key for threeseconds until the intermittent chime beep is heard. This means thatthe muting feature has been activated. If a continuous beep isheard, this means that the muting feature has been deactivated. Toenable chiming when there is no AC power (orange “power” LEDoff) press and hold the [7] key for 3 seconds until the intermittentchime beep is heard. If there is more than 1 keypad in the system,please "chime" program each keypad separately. Keypad chimesmust be reprogrammed if the panel suffers a total power loss.Key [1]-[6]: Turns chime "on" or "off" in zones numbered 1-6Key [7]: Turns chime “on” or “off” when there is no AC power(orange “power” LED off)Key [8]: Turns chime "on" and "off" for the local keypad zoneKey [9]: Turns the keypad’s alarm sounder muting "on" or "off"

7URXEOH 'LVSOD\ 0RQLWRULQJTrouble conditions are continuously monitored by the control panelwhich are displayed on the keypad. When a trouble conditionoccurs, the “TRBL” indicator will illuminate and the keypad willsound an intermittent beep if the Audible Trouble Warning (seesection 11.11) is enabled. Press the [trbl] key to switch to “troubledisplay” mode. The “TRBL” indicator will flash and any illuminatedkeys correspond to a trouble condition as described below. Pressany key to exit “trouble display” mode.

12.12.1 No Battery/Low Batt ery – “1”The control panel conducts a dynamic battery test under load every60 seconds. The illumination of the “1” indicator denotes that theback-up battery is disconnected or that the battery should bereplaced, as it will not provide adequate back-up current in case ofAC loss. If the control panel is currently running on battery power,the illumination of the “1” indicator denotes that the battery voltagehas dropped to 10.5 VDC or lower.

12.12.2 Power Failure – Key “2”The control panel conducts a dynamic battery test under load every60 seconds. The control panel will detect a power loss if acontinuous loss of AC (≤12.5VAC) has occurred during the periodbetween two AC power tests (64 to 116 seconds). If a power lossremains present throughout the Power Failure Report Delay (seesection 8.9), the control panel will transmit the report codeprogrammed at address 507 and the “TRBL” indicator will flashrapidly indicating a power failure. The trouble indicator is restored ifAC is detected during the dynamic battery test. You can remove thepower failure trouble indicator from the trouble display by enablingthe Exclude Power Failure From Trouble Display option (see section11.10).

12.12.3 Bell Disconnected – “4”The illumination of the “4” indicator denotes that there is no bell orsiren connected to the bell output terminals of the control panel.Please note that when connecting a bell or siren to an optional relayoutput the trouble indicator will always be on. To avoid this, connecta 1KΩ resistor across the bell output. The control panel onlyrecognizes bells or siren connected directly to the bell output of thecontrol panel not those connected through a relay.

DE5281 25

12.12.4 Maximum Bell current – “5”The bell output is microprocessor controlled and will automaticallyshutdown when the current exceeds 3A upon alarm. If this occurs,the “5” indicator will illuminate. After opening the short or reducingthe load, the bell current is restored upon the following alarmgeneration.

12.12.5 Maximum Auxiliary Current – “6”The illumination of the “6” indicator denotes that the auxiliary currenthas exceeded 1A. This will cause automatic shutdown of theauxiliary output. After opening the short or reducing the load, thecontrol panel will restore power to the auxiliary output following thedynamic battery test (approximately 60 seconds).

12.12.6 Communicator Report Failure – “7”If the control panel was unsuccessful at attempting communicationwith the central station computer, the “7” indicator will illuminate.

12.12.7 Timer Loss – “8”The illumination of the “8” indicator denotes that the timer must bere-programmed. To re-program the timer press:[ENT] + [Installer, Master or User 1 Code] + [MEM] + 2 digits (00 to23) representing hours + 2 digits (00 to 59) representing minutes.

12.12.8 Tamper/Zone Wiring Failure – “9”If the Tamper/Wire Fault Recognition Options (see section 11.7) areenabled, the “9” indicator will illuminate to indicate a short or cut ona zone input. In order to provide line short recognition the zone

connections must use EOL resistors (see section 3.9, Zone InputTerminal Connections).

12.12.9 Telephone Line Monitoring – “10”If the Telephone Line Monitoring (TLM) feature (see section 11.1) isenabled, the “10” indicator will illuminate to indicate that the controlpanel has not detected the presence of a telephone line for 30seconds.

12.12.10 Fire Trouble – “HOME”The illumination of the “HOME” indicator denotes a tamper on zone3, if identified as a fire zone (see section 7.5, “24 Hour” & FireZones).

12.13 Key Access ProgrammingThis method allows for quick programming of features withoutentering addresses or section numbers. The following features areprogrammed using the installer code as well as the master code anduser 1 codes.Auto Arm Time: for details see page section 9.1.1Panel Time: for details see page section 11.5Manual Test Report: for details see page section 8.8Installer Test Mode: for details see page section 11.9Cancel Communication Attempts:To cancel communication attempts until the next reportable eventpress: [ENT] + [INSTALLER CODE] + [HOME]

:$55$17<:$55$17<

Visonic Ltd. and/or its subsidiaries and its affiliates ("the Manufacturer") warrants itsproducts hereinafter referred to as "the Product" or "Products" to be in conformance withits own plans and specifications and to be free of defects in materials and workmanshipunder normal use and service for a period of twelve months from the date of shipment bythe Manufacturer. The Manufacturer's obligations shall be limited within the warrantyperiod, at its option, to repair or replace the product or any part thereof. The Manufacturershall not be responsible for dismantling and/or reinstallation charges. To exercise thewarranty the product must be returned to the Manufacturer freight prepaid and insured.This warranty does not apply in the following cases: improper installation, misuse,failure to follow installation and operating instructions, alteration, abuse, accident ortampering, and repair by anyone other than the Manufacturer.

This warranty is exclusive and expressly in lieu of all other warranties, obligations orliabilities, whether written, oral, express or implied, including any warranty ofmerchantability or fitness for a particular purpose, or otherwise. In no case shall theManufacturer be liable to anyone for any consequential or incidental damages for breachof this warranty or any other warranties whatsoever, as aforesaid.

This warranty shall not be modified, varied or extended, and the Manufacturer does notauthorize any person to act on its behalf in the modification, variation or extension of thiswarranty. This warranty shall apply to the Product only. All products, accessories orattachments of others used in conjunction with the Product, including batteries, shall becovered solely by their own warranty, if any. The Manufacturer shall not be liable for anydamage or loss whatsoever, whether directly, indirectly, incidentally, consequentially orotherwise, caused by the malfunction of the Product due to products, accessories, orattachments of others, including batteries, used in conjunction with the Products.

The Manufacturer does not represent that its Product may not be compromised and/orcircumvented, or that the Product will prevent any death, personal and/or bodily injuryand/or damage to property resulting from burglary, robbery, fire or otherwise, or that theProduct will in all cases provide adequate warning or protection. User understands that aproperly installed and maintained alarm may only reduce the risk of events such asburglary, robbery, and fire without warning, but it is not insurance or a guarantee thatsuch will not occur or that there will be no death, personal damage and/or damage toproperty as a result.

The Manufacturer shall have no liability for any death, personal and/or bodily injuryand/or damage to property or other loss whether direct, indirect, incidental,consequential or otherwise, based on a claim that the Product failed to function. However, if the Manufacturer is held liable, whether directly or indirectly, for any loss ordamage arising under this limited warranty or otherwise, regardless of cause or origin,the Manufacturer's maximum liability shall not in any case exceed the purchase price ofthe Product, which shall be fixed as liquidated damages and not as a penalty, and shallbe the complete and exclusive remedy against the Manufacturer.

Warning: The user should follow the installation and operation instructions and amongother things test the Product and the whole system at least once a week. For variousreasons, including, but not limited to, changes in environmental conditions, electric orelectronic disruptions and tampering, the Product may not perform as expected. Theuser is advised to take all necessary precautions for his /her safety and the protection ofhis/her property.

6/91

VISONIC LTD. (ISRAEL): P.O.B 22020 TEL-AVIV 61220 ISRAEL. PHONE: (972-3) 645-6789, FAX: (972-3) 645-6788VISONIC INC. (U.S.A.): 10 NORTHWOOD DRIVE, BLOOMFIELD CT. 06002-1911. PHONE: (860) 243-0833, (800) 223-0020 FAX: (860) 242-8094VISONIC LTD. (UK): UNIT 1, STRATTON PARK, DUNTON LANE, BIGGLESWADE, BEDS. SG18 8QS. PHONE: (01767) 600857 FAX: (01767) 601098

VISONIC LTD. 1998 MAESTRO-600, MAESTRO-1000 DE5281- (REV. 0, 8/98)